Safety 1st MultiFit 3-in-1 car seat User manual

4358-6751
6.4.15
MultiFit
3-in-1 Car Seat
rear-facing child restraint
5-40 lb (2.3-18 kg) and 19-40 in. (48-101.6 cm)
forward-facing child restraint
22-40 lb (10.1-18 kg) and 29-43 in.
(73.6-110.1 cm) and at least 2 years old
booster seat
40-100 lb (18.1-45.4 kg) and
43-52 in. (110.1-132.1 cm)
and at least 4 years old
KEEP INSTRUCTIONS FOR
FUTURE USE.
Read all instructions
before using this
child restraint.
To see installation videos, scan the QR Code
or visit www.safety1st.com
Failure to follow the warnings on the labels and in the
instruction manual can result in serious injury or death
to your child.
©2015 Dorel Juvenile.
4358-6751 MultiFit 3-in-1.indd 1-2
6/4/15 10:23 AM
Important Symbols
Vehicle Belts
See pages 29-30 for vehicle belt information.
LATCH
See page 28 for LATCH information and storage
location.
Choosing Rear Facing, Forward Facing, or
Booster Seat
Your child’s height, weight, and age determine how your child
restraint should be placed in the vehicle.
Tether
See page 42 for Tether information.
Instruction Manual Storage
See page 2 for storage location.
To help you recognize instructions which are most
critical to your child’s safety, we use this symbol.
Failure to follow these warnings can result in the
serious injury or death of your child.
WARNING: Verify your child’s weight and height (do
not guess) before choosing the child restraint’s position.
LATCH Install Page 33
REAR FACING
5-40 lb (2.3-18 kg)
19-40 in. (48-101.6 cm)
FORWARD FACING
22-40 lb (10.1-18 kg)
29-43 in. (73.6-110.1 cm)
At least 2 years old
Vehicle Belt Install Page 38
See page 3 to
adjust internal
harness system
+
LATCH Install Page 43
+
Vehicle Belt Install Page 47
BOOSTER SEAT
40-100 lb (18.1-45.4 kg)
43-52 in. (110.1-132.1 cm)
At least 4 years old
4358-6751 MultiFit 3-in-1.indd 3-4
See page 15 to
store internal
harness system
Lap and Shoulder Belt
Install Page 50
6/4/15 10:23 AM
Table of Contents
Getting Started..................................... 1
Parts of the Child Restraint....................................... 1
Prepare Child Restraint to Fit Your Child .................... 3
How Does Your Child Fit? ......................................... 5
Changing Position of Buckle ..................................... 6
Adjusting Headrest/Harness Height ............................ 8
Harness System Adjustments for Smaller Infants ........ 9
Securing Child in Child Restraint ............................... 12
General Use ........................................... 14
Reclining Child Restraint .......................................... 14
Storing Harness System ........................................... 15
Removing Seat Pad for Cleaning ............................... 18
Installing Harness System ........................................ 21
Accessories on Select Models .................................. 24
Safety Information ............................... 25
Rear Facing ........................................... 32
LATCH Installation ............................................. 33
Vehicle Belt Installation ..................................... 38
Forward Facing .................................... 41
Tether Use ........................................................ 42
LATCH Installation ............................................. 43
Vehicle Belt Installation ..................................... 47
Booster Seat ......................................... 49
Lap and Shoulder Belt Installation ...................... 50
Important Information ........................ 52
Using a Locking Clip ................................................ 52
Troubleshooting... .................................................... 54
Dorel Juvenile Group Information... ........................... 54
Registration and Safety Notices ................................ 55
Replacement Parts Order Form ................................. 56
Warranty................................................................. 58
Child Restraint Use .................................................. 25
Installation in Vehicle ............................................... 25
Vehicle Seating Position ........................................... 26
Vehicle Information ............................. 27
Understanding Your Vehicle ...................................... 27
Choosing LATCH or Vehicle Belts .............................. 28
Knowing Your Vehicle Belts ....................................... 29
Aircraft Information ................................................. 31
4358-6751 MultiFit 3-in-1.indd 5-6
6/4/15 10:23 AM
Parts of the Child Restraint
Front View
Side View
A
J
B
C
K
L
M
N
O
P
G
D
Harness System Detail
Back View
H
Q
E
P
F
I
R
S
T
U
L
X
Y
A. Headrest/Harness
Adjustment Levers
B. Adjustable Headrest
C. Shoulder Belt-Positioning
Guide (behind headrest pad)
D. Removable Cup Holder
(see page 24)
1
4358-6751 MultiFit 3-in-1.indd 7-8
E. Harness Release Lever
(under flap)
F. Recline Handle
G. Easy Out Harness Holders
H. Body Pillow (see page 24)
I. Harness Adjustment Strap
J. Rear-Facing Level Line
K. Forward-Facing Belt
Path
L. LATCH Attachment for
Storage
M. Shell (child restraint)
N. Base
O. Rear-Facing Belt Path
P. LATCH (see page 28)
Q. Upper Shoulder Harness
Slots
L
V
W
R. Chest Clip
S. Lower Shoulder Harness
Slots for Smaller Infants
T. Harness Straps
U. Buckle
V. Splitter Plate
W. Instruction Manual Storage
(in bottom of base)
X. Tether (see page 42)
Y. Tether Attachment for
Storage
2
6/4/15 10:23 AM
Prepare Child Restraint to Fit Your Child
2. Or the buckle tongues can be
placed into the slots in the harness
holders as shown.
1. Fully Loosen Harness
Straps
Push down on harness release
lever (under flap on front of seat
pad) while pulling out on harness
straps as shown.
2. Unbuckle Harness
Press in towards the top of the red
button.
Pull buckle tongues out.
3. Release Chest Clip
Press on chest clip release button
and pull apart.
1
3
4358-6751 MultiFit 3-in-1.indd 9-10
4. Place Harness Straps
Out of Way
The Easy Out Harness Holders can
be used two ways.
1. You can secure the harness
straps around them as shown.
2
5. Place Child in
Child Restraint to
Determine Proper
Harness Fit
The child’s bottom and back
should be flat against the child
restraint.
See page 5 for fit guidelines.
4
6/4/15 10:23 AM
How Does Your Child Fit?
Use the guidelines below to determine if the buckle and harness
strap are in the right place for your child.
REAR FACING
1
2
Start in the 1st slot and adjust outward as your
child grows. Buckle should be used in the slot
closest to your child but not underneath or behind
your child. 1st or 2nd slot MUST be used.
Always choose the shoulder harness slots that are
closest to your child’s shoulder height. Harness
strap MUST be at or slightly below shoulders.
If the lower shoulder harness slots for smaller
infants are above the child’s shoulders with the
headrest in the lowest position, do not use this child restraint.
Changing Position of Buckle
1. Unbuckle Harness
Press in towards the top of the red
button.
Pull buckle tongues out.
2. Fully Recline the Child
Restraint
Pull out on recline handle and push
top of child restraint back.
FORWARD FACING
1
2
3
Start in the 1st slot and adjust outward as your
child grows. Buckle should be used in the slot
closest to your child but not underneath or behind
your child. Any slot can be used.
Always choose the shoulder harness slots that are
closest to your child’s shoulder height. Harness
strap MUST be at or slightly above shoulders.
If the upper shoulder harness slots are below the
child’s shoulders with the headrest in the highest
position and the child weighs at least 40 lb (18 kg) and is at least 4
years old, you must convert the child restraint to a booster seat.
To change buckle position, see pages 6-7.
To adjust headrest/harness height, see page 8.
To make adjustments for smaller infants, see pages 9-11.
5
4358-6751 MultiFit 3-in-1.indd 11-12
3. Locate Buckle’s Metal
Retainer
Reach under the seat between the
base and shell and through the
recline handle.
4. Rotate Metal Retainer
and Push It Up Through
Shell and Pad
continued on next page
6
6/4/15 10:23 AM
Adjusting Headrest/Harness Height
5. From Top of Seat,
Pull Buckle Out of Shell
and Pad
1
2
3
6. Insert Buckle’s Metal
Retainer into Slot
Closest to Child
Buckle MUST face out. You MUST
use the 1st or 2nd buckle slots
when child restraint is used rear
facing. Any slot can be used when
forward facing.
7. Reach Under the Seat
Between Base and Shell
and Through Recline
Handle
Pull metal retainer completely
through pad and shell.
8. Check Buckle
Pull up on buckle to make sure it
is secured. The buckle MUST not
pull out.
WARNING: Failure to place buckle’s metal retainer
completely through pad and shell can result in serious
injury or death.
7
4358-6751 MultiFit 3-in-1.indd 13-14
1. Fully Loosen Harness
Straps
Push down on harness release
lever (under flap on front of seat
pad) while pulling out on harness
straps as shown.
2. To Adjust Headrest/
Harness Height
Rotate headrest/harness
adjustment levers inward.
Move the headrest up or down to
the proper height for your child.
See page 5 for fit guidelines.
Release it into slot to lock. Make
sure it is securely locked into
place.
WARNINGS: Make sure that the harness height is
correct for your child’s size.
Do not use this child restraint rear facing unless
the top of your child’s head is at least 1 in. (2.5
cm) below the top of the child restraint’s headrest.
Do not use this child restraint forward facing if the
the tops of your child’s ears are above the top of
the child restraint’s headrest in its highest
position.
Failure to follow these steps can result in serious injury
or death.
8
6/4/15 10:23 AM
Harness System Adjustments for
Smaller Infants
When using the lower shoulder harness slots for smaller infants,
you MUST use the body pillow and the headrest MUST be in the
lowest position.
1. With Buckle in the 1st Slot,
Fully Recline the Seat
If you need to move the buckle to the 1st
slot, see page 6.
2. Lift Pad Off of Front of
Child Restraint
3. From Bottom of Seat, Pull
Metal Retainer Down and
Push It Up into Middle Slot
As Shown
4. From Top of Seat, Lay the
Metal Retainer Flat Against
the Shell As Shown
5. Replace Pad and Check
Buckle
Pull up on buckle to make sure it is
secured. The buckle MUST not pull out.
6. Adjust the Headrest to the
Lowest Position
The headrest MUST be in the lowest
position.
7. Fully Loosen Harness
Straps
Push down on harness release lever
(under flap on front of seat pad) while
pulling out on harness straps as shown.
8. From Back, Remove Harness
Strap Loops From Splitter
Plate
9. Pull Harness Straps Out of
Upper Shoulder Harness
Slots
10. Pull Body Pillow Forward
Away from Seat
Thread harness straps through slots in
pillow.
You MUST use the body pillow.
9
4358-6751 MultiFit 3-in-1.indd 15-16
continued on next page
10
6/4/15 10:24 AM
Securing Child in Child Restraint
11. Pull Bottom of Headrest
Pad Off of Headrest
Thread harness straps through slots in
headrest pad.
Thread harness straps through lower
shoulder harness slots in headrest and
through the slots in seat back (shell).
12. From the Back, Pull
Harness Straps Through
Shell
Harness straps MUST be in shoulder
harness slots BELOW the metal bar as
shown. DO NOT twist harness straps.
13. Attach 2nd Harness Strap
Loops to Splitter Plate As
Shown
Sewn ends of the harness strap loops
MUST face towards you.
DO NOT twist harness straps or harness
adjustment strap.
1. Place Child in Child
Restraint
The child’s bottom and back should
be flat against the child restraint.
Position harness strap over child’s
shoulders and thighs.
2. Buckle Harness
Push buckle tongues into buckle
until you hear them “click.”
Pull up on harness strap to make
sure buckle is locked.
3. Close Chest Clip
Insert right half of chest clip into
left half and snap together.
Make sure the same harness strap loops
are fitted COMPLETELY ON both sides
of the splitter plate.
sewn
end
Replace headrest pad around bottom
of headrest.
Correct
WARNINGS: Harness system must be installed correctly.
The harness strap must be returned to the upper shoulder
harness slots as your child grows.
Failure to follow these steps can result in serious injury or
death.
11
4358-6751 MultiFit 3-in-1.indd 17-18
4. Tighten Harness
Pull on harness adjustment strap
to tighten harness snugly.
continued on next page
12
6/4/15 10:24 AM
Reclining Child Restraint
5. Position Chest Clip
The chest clip must be placed at
mid-chest (even with armpits) and
away from the child’s neck.
6. Check Harness Tightness
Try to pinch the harness at the
shoulders vertically between index
finger and thumb as shown.
If your fingers slip off, the harness is
tight enough.
If you can pinch the harness strap, tighten more. The harness
straps should be snug throughout their length.
WARNINGS: Failure to fasten and tighten the harness
system correctly may allow the child to be ejected from
the child restraint in a crash or sudden stop causing
serious injury or death.
Do not mistake comfort for safety. Harness system must
be snugly adjusted.
Snug harness straps should not allow any slack. They lay in
a relatively straight line without sagging. They do not press
on the child’s flesh or push the child’s body into an unnatural
position.
1
2
3
This child restraint has 3 positions:
Rear Facing - 2 and 3
For children who cannot sit up
unassisted, the level line on shell
MUST be parallel with the ground.
For children who can sit up
unassisted, you may rotate the
child restraint to be more upright in
position 2.
Forward Facing - 1 Upright
Booster Seat - 1 Upright
NOTE: When forward facing, the reclined positions are to be
used only to install the child restraint and booster seat flush
against the vehicle seat back. Vehicle seat back must be
upright.
To recline, pull out on recline handle
and push top of child restraint back.
For upright, pull out on recline
handle and pull top of child restraint
forward.
To Remove Child From Child Restraint:
1. Loosen Harness Strap
2. Unbuckle Harness
3. Release Chest Clip
4. Remove Child
13
4358-6751 MultiFit 3-in-1.indd 19-20
14
6/4/15 10:24 AM
Storing Harness System
Only store the harness system when converting child
restraint into a booster seat.
To remove accessories see page 24.
1. Fully Loosen Harness
Straps
Push down on harness release
lever (under flap on front of seat
pad) while pulling out on harness
straps as shown.
5. Adjust the Headrest
to the Highest Position
6. Undo Fasteners on
Headrest Pad As Shown
2. Unbuckle Harness
Press in towards the top of the red
button.
Pull buckle tongues out.
3. Locate Buckle’s Metal
Retainer
Fully recline the child restraint and
reach under the seat between the
base and shell and through the recline handle. Rotate metal retainer
and push it up through shell and
pad.
4. From Top of Seat,
Pull Buckle of Shell and
Pad
Store the buckle in a safe place for
future use.
15
4358-6751 MultiFit 3-in-1.indd 21-22
7. Pull Headrest Pad Off
Bottom of Headrest
As Shown
8. Undo Fasteners on Seat
Pad As Shown
continued on next page
16
6/4/15 10:24 AM
Removing Seat Pad for Cleaning
9. Thread Harness Straps
into Slots on Sides of
Headrest As Shown
10. Place Chest Clip,
Harness Straps, and
Buckle Tongues Behind
Headrest and Seat Pad
As Shown
Push chest clip up so it is behind
the headrest.
You DO NOT need to remove the harness system to remove
the pad from the shell.
To remove accessories see page 24.
1. Unbuckle Harness
Press in towards the top of the red
button.
Pull buckle tongues out.
2. Adjust the Headrest
to the Highest Position
3. Undo Fasteners on
Headrest Pad As Shown
11. Tighten Harness
Pull on harness adjustment strap
to remove any slack from the
harness system.
12. Pull Headrest Pad Down
and Wrap Around
Bottom of Headrest
Attach fasteners on headrest pad
and seat pad.
17
4358-6751 MultiFit 3-in-1.indd 23-24
4. Pull Elastic Straps
on Headrest Pad Over
Headrest/Harness
Adjustment Levers As
Shown
continued on next page
18
6/4/15 10:24 AM
5. Pull Headrest Pad Off
Bottom of Headrest
As Shown
Remove headrest pad from shell.
9. Pull Pad Down and
Off Bottom of
Harness Holders
Pull up to remove completely.
6. Undo Fasteners on Seat
Pad As Shown
10. From the Top, Pull Pad
Off of Shell
7. Remove Cupholder
See page 24.
WARNINGS: Do not use child restraint without the
seat pad. Failure to do this can result in serious injury or
death.
Cleaning Pad and Accessories
Machine wash all pieces separately with cold water on a gentle cycle.
Do not use bleach. Tumble dry separately for 10-12 minutes on low
heat. Remove immediately.
The cupholder is dishwasher safe.
8. Pull Pad Off Sides and
Bottom of Shell
Cleaning Harness Strap
Spot clean using warm sudsy water and damp cloth.
Replacing Pad
Adjust the headrest to the highest position. Starting from the bottom,
gently pull headrest pad onto headrest. Place elastic straps on headrest pad around headrest/harness adjustment levers. Slide harness
straps into slots in pad. Attach fasteners.
19
4358-6751 MultiFit 3-in-1.indd 25-26
Starting from bottom of child restraint, slip pad on shell. Pull harness
adjustment strap through pad. Wrap pad around bottom and sides
of shell. Push harness holders through slots in pad. Push pad behind
headrest. Wrap around the top of shell. Slide harness straps into slots
in pad. Attach fasteners. Attach cupholder.
20
6/4/15 10:24 AM
Installing Harness System
1. Fully Recline the Child
Restraint
Pull out on recline handle and push
top of child restraint back.
2. Insert Buckle’s Metal
Retainer into Slot
Closest to Child
1
2
3
Buckle MUST face out. You MUST
use the 1st or 2nd buckle slots
when child restraint is used rear
facing. Any slot can be used when
forward facing.
3. Reach Under Seat
Between Base and Shell
and Through Recline
Handle
Pull metal retainer completely
through pad and shell.
4. Check Buckle
Pull up on buckle to make sure it
is secured. The buckle MUST not
pull out.
21
4358-6751 MultiFit 3-in-1.indd 27-28
5. Adjust the Headrest
to the Highest Position
6. Undo Fasteners on Seat
and Headrest Pad and
Pull Headrest Pad Off
Bottom of Headrest
Unthread harness straps from slots
on side of headrest.
Loosen harness straps.
Pull chest clip, harness straps, and
buckle tongues out from behind
the headrest and seat pad.
Slide harness straps into slots in
headrest pad and in seat pad.
Attach fasteners.
If you have removed the harness straps from the
splitter plate, and the buckle tongues and chest
clip have been unthreaded from the harness
straps, follow the steps below to rethread them.
1. Thread Buckle and
Chest Clip
Harness strap ends go through
the back of buckle tongues and
through the chest clip front to
back as shown.
continued on next page
22
6/4/15 10:24 AM
Accessories on Select Models
2. Thread Harness Straps
into Shoulder Harness
Slots
If you will be using the lower
shoulder harness slots for smaller
infants, see pages 9-11.
3. From Back, Thread
Harness Straps OVER
Metal Bar
Removable Cupholder
To remove cupholder, twist the cupholder
counterclockwise.
Pull out of slot in shell.
The cupholder is dishwasher safe.
To install cupholder, align tabs on bottom
of cupholder with slots in shell. Twist clockwise to lock in place.
DO NOT twist harness straps.
4. Attach 1st Harness Strap
Loops to Splitter Plate
As Shown
Sewn ends of the harness strap
loops MUST face towards you.
DO NOT twist harness strap or
harness adjustment strap.
Make sure the same harness
strap loops are fitted
COMPLETELY ON both sides of
the splitter plate.
sewn
end
Correct
WARNINGS: Harness system must be installed
correctly. Failure to follow these steps can result in serious
injury or death.
23
4358-6751 MultiFit 3-in-1.indd 29-30
Body Pillow
When using the lower shoulder harness
slots for smaller infants, you MUST use
the body pillow.
To remove body pillow, slide pillow out
from behind the harness straps.
Or from the back of seat, remove harness
strap loops from splitter plate. From the
front, pull harness straps out of shell and
body pillow.
Rethread harness straps: For lower
shoulder harness slots for smaller
infants, see pages 9-11. For upper
shoulder harness slots, see page 23.
24
6/4/15 10:24 AM
Child Restraint Use
Do not use this child restraint unless the child is 5-100 lb
(2.3-45.4 kg) and 19-52 in. (48-132.1 cm).
Never take your child out of the child restraint while the
vehicle is moving.
Never leave child unattended.
Placing your child in a hot child restraint may result in
burns.
Do not use a child restraint with damaged or missing parts.
Do not use cut, frayed, or damaged harnesses.
Do not substitute parts or try to modify the child restraint in
any way.
Do not lubricate buckles and fasteners.
Do not use any child restraint accessory except those approved by Dorel Juvenile Group.
Never allow any child to play with this child restraint; it is
not a toy.
Do not remove or cover up any of the warning labels or
other labels on the child restraint.
Read all instructions for additional warnings.
On the side of the child restraint there is a date of manufacture label. Do not use this child restraint more than 10 years
after the date of manufacture.
Installation in Vehicle
Check the vehicle belt or LATCH belt before each use. Use
only if the belt is tightened properly and locked securely in
place.
This child restraint should be securely belted in the vehicle
even when not in use. In a crash or sudden stop, an unsecured child restraint could injure occupants.
Do not use a child restraint that has been in a crash. You
must get a new child restraint.
25
4358-6751 MultiFit 3-in-1.indd 31-32
Vehicle Seating Position
Never place a child rear facing in a seating
position with an active frontal air bag.
Check the vehicle owner’s manual for more information about air bag/child restraint use.
Use the child restraint only on vehicle seats
that face forward.
Do not use on seats that face the sides or
rear of the vehicle.
Use the center seating position if possible.
For vehicles without a back seat, refer to your vehicle
owner’s manual.
If you are not sure where to place the child restraint in your vehicle,
consult your vehicle owner’s manual, contact Dorel Juvenile Group
Consumer Relations Department, or visit your local Child Passenger
Inspection Station. Go to http://www.safercar.gov/cpsApp/cps/index.
htm to find your closest station.
Children are safer when properly
restrained in rear seating
positions than in the front
seating positions.
According to National Highway Traffic Safety Administration
information, children in rear seating positions are statistically safer, whether you have air bags, advanced air bags, or
no air bags at all.
To avoid your child being seriously burned, take the following precautions:
1. Park in the shade or where sun does not directly hit the child
restraint.
2. Cover the child restraint with a sheet or blanket when not in use.
3. Check for hot seat and buckles before placing child in child
restraint.
To help protect your vehicle seat’s upholstery from damage, use a
single layer towel underneath and behind child restraint.
26
6/4/15 10:24 AM
Understanding Your Vehicle
Your vehicle’s features may be considerably different
than those pictured here.
Choosing LATCH or Vehicle Belts
LATCH Anchor
Bars
Adjuster
LATCH Hooks
Seat Bight
Consult your vehicle owner’s manual to help identify your
vehicle’s specific features and locations.
Air Bags
LATCH Storage
LATCH Anchors
Located in the seat bight
Tether Anchors
For Tether Strap
(Forward Facing with Internal Harness Only)
Vehicle Seat Belts
27
4358-6751 MultiFit 3-in-1.indd 33-34
The LATCH System
LATCH (Lower Anchors and Tethers for
CHildren) is a universal system for installing child restraints without using vehicle
seat belts.
The LATCH system can ONLY be used in
vehicles that have the LATCH anchor bars
installed and designated LATCH seating
positions. Most vehicles manufactured
after September 2002 are equipped
with LATCH. Check your vehicle owner’s
manual to see which seating positions
may be equipped with the LATCH system.
When installing this child restraint
with vehicle belts or when using as
a booster seat, the LATCH hooks and
belt MUST be properly stored. To store
LATCH on this child restraint: Thread
LATCH belt through rear-facing belt path.
Then attach hooks to storage attachments
as shown. Gently pull free end of belt to
remove slack.
Vehicle Belts
If LATCH is not an option, you must use the
vehicle seat belt system to install the child
restraint.
There are some vehicle belts that will not
work with a child restraint or will require
special attention. Check your vehicle
owner’s manual for specific instructions.
WARNINGS: When used correctly the LATCH or vehicle
belts are equally safe. Do not use both the LATCH belt and
vehicle belt at the same time.
28
6/4/15 10:24 AM
Knowing Your Vehicle Belts
29
Review your vehicle owner’s manual for vehicle seat belt use with
child restraints. This is your best source for information concerning
your vehicle.
Not all vehicle belts will work with this child restraint. This child
restraint must be tightly locked in place at all times. You must
determine if your vehicle’s belts are compatible with this child
restraint.
Vehicle Belts
• Automatic/Passive vehicle seat belts
You MUST have a lap belt to install any child
restraint. An automatic (passive) shoulder belt
may or may not have a separate lap belt.
• Do not use with inflatable seat belts
You may need to move the child restraint to another seating location or use LATCH belts only.
• Vehicle belts in center of the door or side panel
You must move the child restraint to another seating location.
• Vehicle belts that are in front of the seat
bight
You may need to move the child restraint to
another seating location.
• ELR (Emergency Locking Retractor) vehicle belts
These belts only lock in a sudden stop or crash, and do not properly secure a child restraint alone.
To determine if you have this type of belt,
gently pull the belt all the way out of the retractor
(spool), let it return several inches, then pull on
it again. If it moves freely, it is an ELR belt. If it is
locked and will not allow any more belt to come out, it is a switchable retractor.
If you have an ELR lap and shoulder belt, review the “Vehicle Latch
Plate” section on page 30 to see if you need a locking clip.
WARNING: ELR lap-only belts MUST NOT be used with
this child restraint.
4358-6751 MultiFit 3-in-1.indd 35-36
• Switchable Retractor
These belts switch from ELR to ALR (Automatic Locking Retractor).
You MUST have the vehicle belts in the locking mode to use them.
With a switchable retractor, pull the shoulder belt all the way out to
switch the retractor into the ALR mode before tightening.
Feed the slack back into the retractor while tightening.
• ALR (Automatic Locking Retractor)
These belts lock after pulling the webbing out and letting the belt
go back into the retractor an inch or two.
With an ALR belt, pull the belt all the way out before threading
through the child restraint.
Vehicle Latch Plates
• Check Latch Plates
Grasp the tongue portion of the
latch plate (the part that goes
Locking Latch
inside the buckle) and pull straight
Plate
out, in line with the lap belt.
If the latch plate does not slide
Sliding Latch
up and down the vehicle belt, you
Plate
have a locking latch plate. You
should not need to use a locking
clip.
Check your vehicle owner’s manual to determine the best way to
lock a child restraint in place and whether the latch plate or retractor will accomplish this. If the latch plate slides up and down on
the belt, and you have an ELR retractor, you MUST use a locking
clip to install the child restraint. See pages 52-53.
You may not need to use the locking clip with a switchable or ALR
retractor.
30
6/4/15 10:24 AM
Aircraft Information
This restraint is certified for aircraft use when used with the
internal harness.
This child restraint is not certified for use in aircraft when
used as a booster seat because aircraft seats do not have
shoulder belts.
Install the child restraint in a window seat to avoid blocking the
aisle. If the aircraft lap belt is too short, ask the flight attendant for
a belt extender.
Use only on forward facing aircraft seats.
Contact the airline for their specific policies.
Some airlines may ask to see a label stating
that this child restraint is certified for aircraft
use.
There is an airplane certification label located
on the side of this child restraint as shown.
WARNING: Store LATCH belts and tether strap when
using the aircraft belts.
Rear Facing
5-40 lb (2.3-18 kg)
19-40 in. (48-101.6 cm)
LATCH Belt
Lap/Shoulder Belt
Rear Facing Aircraft Installation
For rear facing installation follow pages
38-40.
Lap Belt
Forward Facing Aircraft Installation
For forward facing installation follow
pages 47-48.
31
4358-6751 MultiFit 3-in-1.indd 37-38
WARNINGS: Never install a rear facing child
restraint in the front seat of a vehicle equipped
with an active frontal airbag.
This child restraint MUST always face the rear of the
vehicle when the child is less than two years old.
32
6/4/15 10:24 AM
LATCH Installation
3. Route LATCH Belt
Through Rear-Facing
Belt Path
Do not twist belt.
LATCH adjuster can be on either
side.
Safety Tips
Make sure harness and buckle fit your child correctly before
installing the child restraint. See pages 3-5.
Experts agree that children should remain rear facing as long
as possible. In this child restraint, your child can remain rear
facing up to 40 lb (18 kg) and up to 40 in. (101.6 cm).
WARNINGS: Do not use LATCH belt along with the
vehicle lap or lap/shoulder belt.
Check LATCH belt before each use. Use only if the belt can
be tightened properly and securely.
Do not fasten both LATCH hooks on same LATCH anchor
bar in the vehicle.
Secure the tether hook when used rear
facing. Attach the tether hook to storage attachment as shown and gently
tighten to remove slack.
Failure to follow these warnings can
result in serious injury or death.
1
2
4. Reach Under Pad and
Pull Hook Across to
Opposite Side
Do not twist belt.
Belt MUST be in front of buckle
strap.
You MUST use the 1st or 2nd
buckle slot. Do not place belt
over child’s legs.
5. Finished LATCH Routing
Review your vehicle owner’s manual for LATCH belt use and
LATCH locations.
1. Remove LATCH from
Storage Location
Or remove from forward-facing belt
path if LATCH was used forward
facing.
33
4358-6751 MultiFit 3-in-1.indd 39-40
6. Fully Recline the Child
Restraint
Pull out on recline handle and push
top of child restraint back.
continued on next page
34
6/4/15 10:24 AM
7. Place Child Restraint
Rear Facing in Back
Seat
For children who cannot sit up
unassisted, the level line on shell
MUST be parallel with the ground.
For children who can sit up
unassisted, you may rotate the
child restraint to be more upright
in position 2.
8. Hook LATCH to Vehicle
Anchor
9. Tighten Belt
Place hand in child restraint.
Firmly push child restraint down
and back towards the vehicle seat
back while pulling free end of belt
to tighten.
It may be easier to pull pad away
from shell and tighten the belt
through the belt path opening as
shown.
35
4358-6751 MultiFit 3-in-1.indd 41-42
10. Check Belt Tightness
Hold child restraint at the belt
path with your weakest hand.
Push and pull from side to side.
If it moves more than 1 in. (2.5
cm), try pulling the belt tighter,
try reinstalling the child restraint,
try another seating location, or
switch to using the vehicle belts.
11. Secure Child in Child
Restraint
Recheck level line.
Repeat steps 7-10 if not reclined
correctly.
NOTE: You may need to place
a large rolled towel(s) or foam
pool noodle(s) under front of
child restraint to help achieve the
correct recline angle.
Check often to be sure padding is
still in place and the belt is tight.
continued on next page
36
6/4/15 10:24 AM
Vehicle Belt Installation
To Release LATCH
Remove child from child restraint.
Remove tension from LATCH belt
by pushing down on side of child
restraint with LATCH adjuster. Then
press adjuster button to loosen belt.
Unhook LATCH from bar by squeezing
spring lever, pushing hook back into
the seat bight and twisting. Then pull
it out of the vehicle seat.
Store LATCH when not in use. See
page 28.
Safety Tips
Make sure harness and buckle fit your child correctly before
installing the child restraint. See pages 3-5.
Experts agree that children should remain rear facing as long
as possible. In this child restraint, your child can remain rear
facing up to 40 lb (18 kg) and up to 40 in. (101.6 cm).
WARNINGS: Do not use LATCH belt
along with the vehicle lap or lap/
shoulder belt. Secure LATCH to storage
attachments as shown when installing
with vehicle belts.
Secure the tether hook when used rear
facing. Attach the tether hook to
storage attachment as shown and
gently tighten to remove slack.
Check vehicle belt before each use.
Use only if the belt can be tightened
properly and locked securely in place.
Failure to follow these warnings can
result in serious injury or death.
1. Fully Recline the Child
Restraint
Pull out on recline handle and push
top of child restraint back.
37
4358-6751 MultiFit 3-in-1.indd 43-44
continued on next page
38
6/4/15 10:24 AM
2. Place Child Restraint
Rear Facing in Back
Seat
For children who cannot sit up
unassisted, the level line on shell
MUST be parallel with the ground.
For children who can sit up
unassisted, you may rotate the
child restraint to be more upright
in position 2.
3. Route Vehicle Lap
or Lap/Shoulder Belt
Through RearFacing Belt Path
Review pages 29-30 and your
vehicle owner’s manual to
determine what kind of vehicle
belts you have and how to lock a
child restraint in place.
1
2
39
4358-6751 MultiFit 3-in-1.indd 45-46
4. Reach Under Pad and
Pull Vehicle Belt Across
the Shell
Do not twist belt. Belt MUST be
in front of buckle strap.
You MUST use the 1st or 2nd
buckle slot. Do not place belt over
child’s legs. Buckle vehicle belt.
5. Tighten Belt
Place hand in child restraint.
Firmly push child restraint down
and back towards the vehicle seat
back while pulling free end of belt
to tighten.
6. Check Belt Tightness
Hold child restraint at the belt path
with your weakest hand.
Push and pull from side to side.
If it moves more than 1 in.
(2.5 cm), try pulling the belt
tighter, try reinstalling the child
restraint, try another seating location, or switch to using the
LATCH belt if available.
7. Secure Child in Child
Restraint
Recheck the level line.
Repeat steps 2-6 if not
reclined correctly.
NOTE: You may need to place
a large rolled towel(s) or foam
pool noodle(s) under front of
child restraint to help achieve the
correct recline angle.
Check often to be sure
padding is still in place and the
belt is tight.
40
6/4/15 10:24 AM
Forward Facing
22-40 lb (10.1-18 kg)
29-43 in. (73.6-110.1 cm)
At least 2 years old
LATCH Belt
with Tether
Tether Use
Always attach, adjust, and secure the top anchorage
(tether) strap when installing the child restraint forward
facing. Tethers improve the installation and stability of child
restraints and reduce the risk of injury.
Attach the tether hook to the tether anchor designated by
your vehicle manufacturer for that seating position. Check
your vehicle owner’s manual for more information.
If the seating position does not have a tether anchor, use a
different seating position or see your dealer or a qualified
mechanic and have one installed. The tether can greatly
improve the performance of this child restraint.
To Adjust Tether Strap:
Lap/Shoulder Belt
with Tether
Lap Belt with
Tether
Pull free
end to
tighten
To tighten: After the child restraint
is locked into place with LATCH or
vehicle belt, push down on child
restraint and gently pull on free end
of tether.
Lift up to
loosen
To loosen: Lift up on tether lock
adjuster and push it towards tether
hook.
WARNINGS: In this child restraint your child MUST be
at least 2 years old before they sit forward facing.
Safety Tip
Experts agree that children should remain rear facing as long
as possible. In this child restraint, your child can remain rear
facing up to 40 lb (18 kg) and up to 40 in. (101.6 cm).
41
4358-6751 MultiFit 3-in-1.indd 47-48
42
6/4/15 10:24 AM
LATCH Installation
Safety Tips
Make sure harness and buckle fit your child correctly before
installing the child restraint. See pages 3-5.
Experts agree that children should remain rear facing as long
as possible. In this child restraint, your child can remain rear
facing up to 40 lb (18 kg) and up to 40 in. (101.6 cm).
2. Route LATCH Belt
Through ForwardFacing Belt Path
Do not twist belt.
LATCH adjuster can be on either
side.
3. Finished LATCH Routing
WARNINGS: Do not use LATCH belt along with the
vehicle lap or lap/shoulder belt.
Check LATCH belt before each use. Use only if the belt can
be tightened properly and securely.
Do not fasten both LATCH hooks on same LATCH anchor
bar in the vehicle.
Failure to follow these warnings can result in serious
injury or death.
Review your vehicle owner’s manual for LATCH belt use
and LATCH locations.
1. Remove LATCH from
Storage Location
4. Place Child Restraint
Forward Facing Flush
Against Vehicle Seat
Back
Do not use any recline positions
except to make the child restraint
flush against the vehicle seat back.
Vehicle seat back must be upright.
5. Loosely Attach Tether
Hook
Check vehicle owner’s manual for
specific location.
43
4358-6751 MultiFit 3-in-1.indd 49-50
continued on next page
44
6/4/15 10:24 AM
6. Hook LATCH to Vehicle
Anchor
7. Tighten Belt
Place knee in child restraint.
Firmly push down while pulling
free end of belt to tighten.
It may be easier to pull pad away
from shell and tighten the belt
through the belt path opening as
shown.
8. Tighten Tether
With knee still in child restraint,
push firmly on the back of the seat
and tighten tether strap.
45
4358-6751 MultiFit 3-in-1.indd 51-52
9. Check Belt Tightness
Hold child restraint at the belt
path with your weakest hand.
Push and pull from side to side.
If it moves more than 1 in. (2.5
cm), try pulling the belt tighter,
try reinstalling the child restraint,
try another seating location, or
switch to using the vehicle belts.
To Release LATCH
Remove child from child restraint.
Remove tension from LATCH belt
by pushing down on side of child
restraint with LATCH adjuster. Then
press adjuster button to loosen belt.
Unhook LATCH from bar by
squeezing spring lever, pushing hook
back into the seat bight and twisting.
Then pull it out of the vehicle seat.
Store LATCH when not in use. See
page 28.
46
6/4/15 10:24 AM
Vehicle Belt Installation
Safety Tips
Make sure harness and buckle fit your child correctly before
installing the child restraint. See pages 3-5.
Experts agree that children should remain rear facing as long
as possible. In this child restraint, your child can remain rear
facing up to 40 lb (18 kg) and up to 40 in. (101.6 cm).
WARNINGS: Do not use LATCH
belt along with the vehicle lap or lap/
shoulder belt. Secure LATCH to storage
attachments as shown when installing
with vehicle belts.
Check vehicle belt before each use.
Use only if the belt can be tightened
properly and securely.
Failure to follow these warnings can
result in serious injury or death.
1. Place Child Restraint
Forward Facing Flush
Against Vehicle Seat Back
Do not use any recline positions
except to make the child restraint
flush against the vehicle seat back.
Vehicle seat back must be upright.
2. Loosely Attach Tether
Hook
Check vehicle owner’s manual for
specific location.
47
4358-6751 MultiFit 3-in-1.indd 53-54
3. Route Vehicle Lap or
Lap/Shoulder Belt
Through ForwardFacing Belt Path
Review pages 29-30 and your vehicle
owner’s manual to determine what
kind of vehicle belts you have
and how to lock a child restraint in place. Do not twist belt.
Buckle vehicle belt.
4. Tighten Belt
Place knee in child restraint.
Firmly push down while pulling
shoulder belt or free end of lap belt to
tighten.
5. Tighten Tether
With knee still in child restraint,
push firmly on the back of the seat
and tighten tether strap.
6. Check Belt Tightness
Hold child restraint at the belt path
with your weakest hand.
Push and pull from side to side.
If it moves more than 1 in. (2.5 cm),
try pulling the belt tighter, try
reinstalling the child restraint, try another seating location, or
switch to using the LATCH belt if available.
48
6/4/15 10:24 AM
Booster Seat
Lap and Shoulder Belt Installation
40-100 lb (18.1-45.4 kg)
43-52 in. (110.1-132.1 cm)
At least 4 years old
Lap/Shoulder Belt
You MUST store the harness system (see pages 15-17) and remove
accessories, except cupholder, (see page 24) to use as a booster seat.
WARNINGS: Do not use the harness system when using
as a booster seat.
Do not use this booster seat if the tops of
your child’s ears are above the top of the
booster seat’s headrest.
Use only the vehicle’s lap and shoulder belt
system when restraining the child in this
booster seat.
Do not use only the lap belt when using
this seat as a booster seat.
The shoulder belt must always be adjusted
snugly across the child’s chest. NEVER
place the shoulder belt under the child’s
arms.
Do not use the LATCH belts or tether strap
when using as a booster seat. Secure both
LATCH and tether strap to their storage
locations.
Failure to follow these warnings can result
in serious injury or death.
49
4358-6751 MultiFit 3-in-1.indd 55-56
1. Place Booster Seat
Forward Facing Flush
Against Vehicle Seat
Back
Do not use any recline position
except to make the booster seat
flush against the vehicle seat back.
Vehicle seat back must be upright.
2. Place Child in Booster
Seat
Tops of child’s ears should be at
the midpoint of the headrest.
Adjust headrest if needed, see
page 8.
3. Position Lap Belt on
Child
Route the lap belt portion of
vehicle belt through the booster
belt path as shown.
The lap belt should lay snugly
across the child’s upper thighs and
not on the stomach.
continued on next page
50
6/4/15 10:24 AM
Using a Locking Clip
4. Buckle Vehicle Belt
5. Position Shoulder Belt
on Child
Slide the shoulder belt under
bottom of the Easy Out Harness
Holder as shown.
Pull up on shoulder belt to tighten.
The shoulder belt should lay
snugly across the center of the
child’s shoulder and across the
chest and not on their face or
neck.
To help position the shoulder
belt, you may need to secure the
shoulder belt in one of the two
shoulder belt-positioning guides
behind headrest pad.
NOTE: Use the shoulder beltpositioning guide only if necessary
to correctly position the shoulder
belt on the child.
Check periodically to make sure
your child has not moved out of
position and loosened the shoulder
belt.
51
4358-6751 MultiFit 3-in-1.indd 57-58
You will rarely need to use a locking clip except in some older
vehicles. Built-in child restraint locking systems have been required
in vehicles since 1996, and many vehicles had these features even
earlier. Review pages 29-30 and your vehicle owner’s manual to
determine if your vehicle belts require a locking clip.
If you need a locking clip immediately, they are likely available at an
auto dealership, an auto store, or where you purchased this child
restraint. You can also email us at [email protected] or call
us at 1-800-544-1108 for one.
A locking clip will not fix all types of seat belt problems. You MUST
have a lap and shoulder belt to use a locking clip. Do not use the
locking clip when using this seat as a booster seat.
For Rear Facing installation, follow pages 38-40 Warnings and
Steps 1-5 before starting locking clip installation.
For Forward Facing installation, follow pages 47-48 Warnings
and Steps 1-4 before starting locking clip installation.
1. Determine Locking Clip Position
Grasp both vehicle belts together just
behind the latch plate to mark the
position for locking clip.
Unbuckle the belt.
NOTE: If the latch plate ends up just
at the belt path opening so you
cannot grasp the vehicle belt at the latch plate, grasp the vehicle
belts on the opposite side of the child restraint, as close to the
latch plate as possible.
2. Attach Locking Clip
Thread both portions of the vehicle
belt onto the locking clip, as close
to the latch plate as possible.
continued on next page
52
6/4/15 10:24 AM
Troubleshooting
3. Position Locking Clip
It should be about 1 in. (2.5 cm)
from vehicle belt’s latch plate.
n. )
1 i5 cm
.
(2
4. Rebuckle Vehicle Belt
1. Locate a Child Safety Seat Inspection Station for hands on
training on how to use your child restraint: Visit your local Child
Passenger Inspection Station or go to http://www.safercar.gov/cpsApp/
cps/index.htm to find your closest station.
2. If the child restraint buckle or harness release lever sticks
or you cannot get the straps tight enough around child: DO
NOT LUBRICATE. Check around lever and retractor for dropped food,
sticky spilled drinks, dirt, leaves, etc. Clean with warm water and/or
remove object with tweezers. If you cannot get the harness to adjust
and remain tight with the buckle securely locked, do not use the child
restraint.
3. If you cannot insert the buckle tongues into buckle, switch
sides and try again.
4. If your harness twists: Straighten the harness each time you
put your child in the child restraint to help prevent twisting. Lock the
buckle and tighten harness so it will be ready for next use.
Dorel Juvenile Group Information
5. Check Belt Tightness
Hold child restraint at the belt path
with your weakest hand.
Push and pull from side to side.
If it moves more than 1 in. (2.5 cm),
try reinstalling the child restraint or
try another seating location.
When installed rear facing,
recheck the level line.
When installed forward facing,
make sure to tighten the tether
strap.
Remove the locking clip when
the seat belt is not being used
with a child restraint.
53
4358-6751 MultiFit 3-in-1.indd 59-60
Thank you for choosing this child restraint. The DJG family is committed to creating child restraints with the most comfort and convenience
available today.
Remember, parents are a child’s first teachers and examples. If you
always buckle your seat belt, your child will think it is the natural thing
to do. Make it a firm rule that the vehicle does not go until everyone is
buckled up. Make no exceptions.
No one can predict if use of a child restraint will prevent injury or death
in a particular crash. However, when combined with careful driving,
proper use of a child restraint can lower a child’s risk of injury or death
in most crashes.
Your child’s safety is worth the time it will take to read and follow these
instructions. After reading, if you still have questions or have any concerns with this child restraint, please contact our Consumer Relations
Department at:
Website: www.safety1st.com
Email: [email protected]
Telephone: 1-800-544-1108
M-TH from 8 A.M. to 6 P.M. EST
FRI from 8 A.M. to 4:30 P.M. EST
Mailing Address:
Dorel Juvenile Group, Inc.
Consumer Relations Department
P.O. Box 2609
Columbus, IN 47202-2609
Fax: 1-800-207-8182
54
6/4/15 10:24 AM
Registration and Safety Notices
Replacement Parts Order Form
Please complete the postage-paid registration card that came
with your child restraint, and send it to us. Child restraints could
be recalled for safety reasons. You must register this restraint to
be reached in a recall. Send your name, address, email address
if available, the restraint’s model number, and manufacturing
date to:
Dorel Juvenile Group, Inc.
Consumer Relations Department
PO Box 2609
Columbus, IN 47202-2609
or call 1-800-544-1108 or register online at www.djgusa.com/
registration/carseat/us.
For recall information, call the U.S. Government’s Vehicle Safety
Hotline at 1–888–327–4236 (TTY: 1–800–424–9153), or go
to http://www.NHTSA.gov.
Complete the form. Your model number and manufacturer date
code MUST be included on the form to ensure proper replacement
parts. The codes can be found on a label on side of child restraint.
Payment in U.S. dollars must accompany your order. Choose parts
needed from the list on the next page. Return the form with payment to:
Dorel Juvenile Group, Inc.
Consumer Relations Department
P.O. Box 2609
Columbus, IN 47202-2609
Fax orders to: 1-800-207-8182
Please make money orders payable to Dorel Juvenile Group, Inc. Fill
in the area on the next page to charge credit card. (Visa or MasterCard only). We do not accept cash, personal checks, or other credit
cards. All outside of U.S. and Canada MUST use credit card.
Ship To: (Please Print)
Name:_______________________________________
Model
Number
Line
Code
Manufacture
Date
Address:_____________________________________
City:_________________________________________
State/Province:_______________Zip:_______________
Telephone: ___________________________________
Example of model number, manufacture date, and line code.
If you don’t have the card or if your
address changes, you will find the model
number, manufacture date, and line code
on the label located on side of shell.
55
4358-6751 MultiFit 3-in-1.indd 61-62
Email Address: ________________________________
We MUST have this information:
Model Number (8 to 9 characters):_________________
Manufacture Date (mm/dd/yyyy):__________________
56
6/4/15 10:24 AM
Replacement Parts List
Warranty
NOTE: If requested color is not available, similar color will be
substituted. Prices are subject to change.
Part
Cost
Qty
Total Cost
Buckle Assembly .............................. $7.99 .... ___ ........ $_______
Seat Pad Set ............................. $99.00 .... ___ ........ $_______
Chest Clip ................................... $1.50 .... ___ ........ $_______
Tether ......................................... $6.00 .... ___ ........ $_______
LATCH.........................................$7.99 .... ___ ........ $_______
Instructions................................. $0.00 .... ___ ........ $_______
Locking Clip ................................ $2.50 .... ___ ........ $_______
Dorel Juvenile Group, Inc. (DJG) warrants this product to the original
retail purchaser as follows:
This product is warranted against defective materials or workmanship for one year from the date of original purchase. An original
receipt is required to validate your warranty. DJG will, at
its option, provide replacement parts or replace this product.
DJG reserves the right to substitute if the part or model has been
discontinued.
To make a claim under this warranty you may email us at
[email protected]; fax us at 1-800-207-8182 24 hours a
day; write to DJG, Consumer Relations Department, P. O. Box 2609,
Columbus, IN 47202-2609; or call 1-800-544-1108 from 8:00
a.m. to 6:00 p.m. EST Monday through Thursday and from 8:00
a.m. to 4:30 p.m. on Friday.
Proof of purchase is required and shipping charges are the
responsibility of the consumer.
Warranty Limitations: This warranty does not include damages
which arise from misuse or abuse of this product.
Limitation of Damages: The warranty and remedies as set forth
are exclusive and in lieu of all others, oral or written, expressed or
implied. In no event will DJG or the dealer selling this product be
liable to you for any damages, including incidental or consequential
damages, arising out of the use or inability to use this product.
Limitation of warranties and other warranty terms and state
law rights:
Any implied warranties, including implied warranties of the
merchantability and fitness for a particular purpose, shall be limited
to the duration and terms of the express written warranty. Some
states do not allow limitations as to how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you.
This warranty gives you specific legal rights, and you may have
other rights, which vary from state to state. Neither DJG nor the
dealer selling this product authorized any person to create for it any
other warranty, obligation, or liability in connection with this product.
Merchandise Total: .............................................. $_______
Up to $25.00 ..................... $5.95
$25.01 to $50.00 .............. $6.95
$50.01 to $75.00 .............. $8.95
$75.01 to $100.00 ............ $9.95
$100.01 to $150.00 .......... $10.95
$150.01 to $200.00 .......... $11.95
$200.01 and up................. $13.95
Outside Continental USA.....$10.00
Sales Tax ............................................................... $_______
(Arizona, California, Georgia, Indiana, Missouri, South Carolina, and Texas
residents add applicable sales tax.)
Grand Total............................................................ $_______
No shipping and handling on instructions for quantities under 6. Add $.50 for each
instruction over 6, then add applicable shipping and handling.
Fill Out For Credit Card
q Visa q MasterCard
Card Exp. Date:
___________________________________________
Cardholder’s Name:
___________________________________________
Card Number:
___________________________________________
Signature:
___________________________________________
57
4358-6751 MultiFit 3-in-1.indd 63-64
CUT ON DOTTED LINE
Shipping and handling:........................................ $_______
58
6/4/15 10:24 AM
">