Mac Tools MDT 10 Operator's Manual
Add to My manuals119 Pages
Mac Tools MDT 10 is a professional scan tool built into a durable AndroidTM tablet. Up to four hours of battery run time. Extremely fast boot time and Swift On function. Wi-Fi and web browser allow full internet access. Built-in training videos to learn scan tool and vehicle test procedures. AutoDetectTM alerts technician when repair information is available. Auto IDTM. Automatically identifies CAN vehicles to quickly set up year, make, model, and engine. Deep Link In-session to Direct-HitTM for identifix® subscribers. Get the most out of your vehicle repairs with Mac Tools MDT 10.
advertisement
ET7200
WARNING
To reduce the risk of injury, read and understand these safety warnings and instructions before using the tool.
Keep these instructions with the tool for future reference. If you have any questions, contact your
MAC TOOLS representative or distributor.
Scan Tool
MDT 10
Operators Manual
TABLE OF CONTENTS
INTRODUCTION ........................................ 3
WARRANTY .............................................. 3
SAFETY DEFINITIONS ................................ 4
SAFETY PRECAUTIONS ............................. 4
GENERAL INFORMATION ............................ 6
Introduction ........................................... 6
Handset ................................................ 7
Handset Ports ........................................ 8
Handset Back ........................................ 9
Vehicle Communication Interface (VCI) .... 10
Add-on Hardware Modules (Optional) ...... 11
Software Descriptions ............................ 11
SETUP .................................................... 12
Docking Station ..................................... 12
Battery Charging ................................... 13
Using the handset ................................. 13
REGISTRATION ........................................ 14
30 Day Trial .......................................... 18
Demo ................................................... 18
Provide Power to VCI ............................. 19
Test Startup and Vehicle Connection ....... 23
Adjust Settings ..................................... 23
GLOBAL OBDII APPLICATIONS ................... 30
Overview ............................................... 30
Diagnostic Functions ............................. 30
Data Stream.......................................... 32
DTCs Modes.......................................... 35
Oxygen (O2) Sensors .............................. 38
Special Tests......................................... 40
Vehicle Info .......................................... 42
SELECTING VEHICLE ................................ 44
Auto ID ................................................ 44
Manual Entry ........................................ 47
Recent ................................................. 50
Favorites............................................... 53
OBD-II ................................................. 55
Heavy Duty ........................................... 56
READ DTCS ............................................. 60
Overview ............................................... 60
Ford/Lincoln/Mercury ............................. 62
GM/GMC............................................... 63
DATA STREAM ......................................... 68
Overview ............................................... 68
SPECIAL TESTS ....................................... 78
Overview ............................................... 78
DIAGNOSTIC INFORMATION ...................... 82
Overview ............................................... 82
MAINTENANCE TESTS ............................. 94
ALL SYSTEM DTC SCAN ........................... 98
Overview ............................................... 98
Browser ............................................... 102
Overview .............................................. 102
AUTOMATED SYSTEM TEST ..................... 104
Overview .............................................. 104
VIEW SAVED TESTS ................................ 111
Overview .............................................. 111
VIEW DATA STREAM RECORDINGS ........... 114
Overview .............................................. 114
SYSTEM WIRING DIAGRAMS ................... 116
Overview .............................................. 116
CUSTOMER SUPPORT ............................. 118
Technical Support ............................... 118
Order Information ................................ 118
Repair Service ..................................... 118
CUSTOMER SERVICE .............................. 119
2
MACTOOLS.COM
INTRODUCTION
The Mac Tools™ MDT 10 is a professional scan tool built into a durable AndroidTM tablet. Up to four hours of battery run time. Extremely fast boot time and Swift On function. Wi-Fi and web browser allow full internet access. Built-in training videos to learn scan tool and vehicle test procedures. AutoDetectTM alerts technician when repair information is available. Auto IDTM. Automatically identifies CAN vehicles to quickly set up year, make, model, and engine. Deep Link In-session to Direct-HitTM for identifix® subscribers. NOTE: Additional safety measures may be required because of your particular application of the tool. Contact your Mac Tools representative or distributor with any questions concerning the tool and its use.
Mac Tools
505 North Cleveland Avenue
Suite 200
Westerville, Ohio 43082
WARRANTY
We warrant that this tool shall be free from manufacturing defects for a period of TWO YEARS from the original purchase date. Our obligation to the original purchaser shall be limited to repairing or replacing, at our expense
(not including shipping charges) a defective tool if returned by the original purchaser within two years from the date of purchase, all incoming shipping charges prepaid. THIS WARRANTY DOES NOT COVER DEFECTS OR
DAMAGES TO THE TOOL (i) after the warranty period expires; (ii) resulting from misuse or abnormal operation;
(iii) resulting from a failure to properly lubricate, maintain or operate the tool; or (iv) resulting from any repair or maintenance services performed by any party other than Mac Tools.
800.MACTOOLS
3
SAFETY DEFINITIONS
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
SAFETY PRECAUTIONS
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD READ AND UNDERSTAND THIS MANUAL AND FOLLOW ALL
SAFETY WARNINGS AND INSTRUCTIONS.
KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, CONTACT YOUR
MAC REPRESENTATIVE OR DISTRIBUTOR.
DANGER:
When an engine is operating, keep the service area well ventilated or attach a building exhaust removal system to the engine exhaust system. Engines produce carbon monoxide, an odorless, poisonous gas that causes slower reaction time and can lead to death or serious personal injury.
WARNING:
• When working with hydraulic or fuel lines, be careful that liquids under pressure do not escape and create a dangerous condition. Use adequate ventilation and make sure there are no sparks or possibility of sparks that may ignite any vapor.
• Wear an American National Standards Institute (ANSI) Z87.1 approved eye shield when testing or repairing vehicles.
• Objects propelled by whirling engine components or pressurized liquids escaping may cause personal injury.
• Set the parking brake and block the wheels before testing or repairing a vehicle. It is especially important to block the wheels on front-wheel drive vehicles because the parking brake does not hold the drive wheels.
• Do not drive the vehicle and operate the software at the same time. Any distractions may cause an accident. Have one person operate the software as another person drives the vehicle.
• Maintain adequate clearance around moving components or belts during testing.
• Moving components and belts can catch loose clothing, body parts, or test equipment and cause serious personal injury or tool damage.
• Automotive batteries contain sulfuric acid and produce explosive gases that can result in serious injury ignition of gases, keep lit cigarettes, sparks, flames, and other ignition sources away from the battery at all times.
• Refer to the service manual for the vehicle being serviced. Adhere to all diagnostic procedures and precautions
Failure to do so could result in personal injury or otherwise unneeded repairs.
• Use only specially designed replacement parts (brake hoses and lines) for ABS equipped vehicles.
4
MACTOOLS.COM
• After bleeding the brake system, check the brake pedal for excessive travel or a ”spongy” feel. Bleed again if either condition is present.
• When installing transmitting devices (Citizen Band radio, telephone, etc) on ABS-equipped vehicles, do not locate the antenna near the ABS control unit or any other control unit.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• To reduce risk of injury, charge only Mac Tools rechargeable batteries for the handset product with the supplied charger. Other types of batteries may burst causing injury to persons and damage.
• Use of an attachment not recommended or sold by the battery charger manufacturer may result in fire, electric shock, or personal injury.
• Do not operate the tool with a damaged cord or connector. Replace damaged cords and connectors immediately.
• Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take the charger to a qualified service person.
• Do not disassemble the charger. Take the charger to a qualified service person if service or repair is necessary.
Incorrect reassembly may result in electric shock or fire Unplug charger before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
• To prevent possible hearing damage, avoid using the tool at high volume levels for long periods.
• Do not expose tool or charger to rain, moisture, or snow.
• Verify that cords are located where they will not be stepped on, tripped over, or otherwise become a safety hazard or subjected to damage or stress.
• Use only batteries that are approved for use with this tool. Use of other types may increase the risk of fire or explosion.
• Do not carry a battery in your pocket, purse, or other container where metal objects (such as car keys or paper clips) could short-circuit the battery terminals. The resulting excessive current flow can cause extremely high temperatures and may result in damage to the battery pack or cause fire or burns.
• The battery poses a burn hazard if you handle it improperly. Do not disassemble it. Handle a damaged or leaking battery with extreme care. If the battery is damaged, electrolyte may leak from the cells and may cause personal injury.
• Keep the battery away from children.
• Do not store or leave your tool or battery near a heat source such as a radiator, replace, stove, electric heater, or other heat-generating appliance or otherwise expose it to temperatures in excess of 60ºC (140ºF). When heated to excessive temperatures, battery cells could explode or vent, causing personal injury or risk of fire.
• Do not dispose of your tool’s battery in a fire or with normal household waste. Battery cells may explode. Discard a used battery according to the manufacturer’s instructions or contact your local waste disposal agency for disposal instructions. Dispose of a spent or damaged battery promptly.
CAUTION:
• To avoid damage or generation of false data, make sure the vehicle battery is fully charged and the connection to the vehicle Data Link Connector (DLC) is clean and secure.
• Do not place the tool on the distributor of a vehicle. Strong electromagnetic interference can damage the tool.
• Never disconnect or reconnect any electrical connector while the ignition is on. Powertrain Control Module (PCM) damage may result.
800.MACTOOLS
5
GENERAL INFORMATION
Introduction
ss02588
1
2
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
BMW
2013
BMW
335I (E92/E93)
xDrive3.0
TIRE PRESSURE
MONITOR
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
3
2:59
4
5
6
7
12 11 10 9 8
Handset Front
1. Vehicle Identification Window
• Where vehicle selections can be made and modified.
2. Camera
• Front facing camera is 5MP.
3. Microphone
• Front facing microphone.
4. Ambient Light Sensor
5. Home Screen Functions
• Read DTCs allows reading, clearing, and printing of vehicle DTCs.
• Data Stream shows live sensor and solenoid data streaming from the vehicle ECU.
• Special Tests Available dependent upon the vehicle and controller selected.
• Diagnostic Information provides diagnostic, repair, and reset information for the selected vehicle.
• Maintenance Tests common scan resets after vehicle service.
• All System DTC Scan will scan all available controllers on the selected vehicle for DTCs.
• Browser Fast Touch™ sites and internet.
• Settings change settings of the tool.
• Automated System Test is a comprehensive vehicle scan containing all DTCs on the vehicle and available OBDII Data.
• View Saved Tests allows the user to view previously ran and saved DTC reads, All System DTC scan, and Automated System Test scans.
• View Data Stream Recordings allows the user to view previously saved data stream recordings.
6
MACTOOLS.COM
• System Wiring Diagrams provides OEM specific, Full color, Full system diagrams.
6. Android Applications Button
• Displays the Apps screen.
7. Camera Button
• Opens the camera application.
8. Screen Shot Button
• Press to take a picture of the current screen.
9. VCI Connection Manager Button
• Opens the VCI Manager.
10. Recent apps button
• Opens a list of thumbnail images of currently running apps.
11. Home Button
• Displays the central home screen.
12. Back Button
• Returns to the previous screen or option.
Handset
The handset is a ruggedized touchscreen tablet equipped with the Android operating system. The power button is located on the top right of the Handset next to the connector panel.
ss02585
Handset Power Button
Power Button Functions
The power button has four functions a. ON: Press the power button to turn the handset on.
b. OFF: Press and release the power button. A pop up window will appear to shut down the handset.
c. ON: If the screen times out or is in standby mode, press and release the power button to wake up the handset. Turn ON: With tool off, press to turn ON d. OFF: Press the power button and hold for 5 seconds to turn the handset off completely (not recommended).
800.MACTOOLS
7
Handset Ports
ss02587 1 2 3 4 5 6 7 8
1. Mini USB
2. VCI Port
3. Ethernet Connector
4. Audio port
5. USB Type “A” port
6. HDMI Port
7. Power port
8. Power Button
9. Speakers
10. Docking Station Port
9 10
Handset Ports
9
8
MACTOOLS.COM
Handset Back
ss02589
1
2
3
1. Light
• The light has two functions
• Camera Flash mode
2. Camera
• Flash Light mode
• Rear Facing Camera is 5MP.
3. Microphone
• Rear Facing Microphone.
Handset Back
800.MACTOOLS
9
Vehicle Communication Interface (VCI)
The Vehicle Communication Interface (VCI) translates vehicle diagnostic data link information for the handset using Wi-Fi wireless technology or a linked cable. The wireless capability of the tool is designed to communicate with the VCI when it is within a range of roughly 30 feet, even though it is possible to go farther. Every shop has different noise that can interfere and hamper the distance of a wireless network. Some types of noise include cordless phones, certain lighting, other wireless networks in the area, and other signals.
ss02586
1
2
3
4
5
6
VCI
1. Power port (used when necessary)
2. DLC/OBDII cable port
3. Power
• Indicates the VCI has received power.
4. PC Connection
• Indicates the VCI is communicating with the PC.
5. Vehicle Connection
• Indicates the VCI is communicating with vehicle by wireless Wi-Fi or USB
6. USB “B” Port
10
MACTOOLS.COM
Add-on Hardware Modules (Optional)
TPMS Tire Pressure Reset (TPR) Tool
The Tire Pressure Reset (TPR) is a fast, simple, easy-touse TPMS activation tool that can be used with the handset or as a stand-alone tool. It works on vehicle TPMS sensors and automatically adjusts activation output power to eliminate cross-activation of near sensors.
ss01533
SELECT
TPMS
TIRE PRESSURE
RESET
TPR
Software Descriptions
Handset Software
The handset comes with the diagnostic software pre-loaded. Set up Docking Station, attach power supply provided with kit and charge battery before use.
The first time the handset is powered up, the user needs to accept the license agreement and review opportunities to provide input that will help improve the handset. Then, the user will have three choices:
• Register Now: Unlocks all functions of handset.
• Trial mode: Unlocks all functions for 30 days.
• Demo Mode: Displays what functions may look like.
Periodically, updates will become available and the user will be notified by an icon on the screen. To update the handset, there must be Wi-Fi or Ethernet connection available.
Software Applications Overview
The handset allows users to diagnose problems on a wide variety of vehicles (from electric to heavy duty vehicles). Users are able to perform common service procedures, maintenance tests, and special tests to find deficiencies with vehicle systems or components.
800.MACTOOLS
11
The handset will display DTCs from OBDI or OBDII systems. Real-time sensor data can be viewed in data stream mode. The user can also obtain diagnostic information regarding repairs.
With the purchase of the Tech-Scope, the user is able to test sensors and systems for proper function. Browser mode allows the user to connect to the internet to find websites that may help with the repair of the vehicle.
The handset comes with wireless communication for ease of use and on-screen help when desired.
SETUP
Docking Station
ss02593
2
1
3
Docking Station
1. Handset
2. Docking Station
3. LED
The Docking Station can be used to store the Handset when not in use. The Docking station can also charge the handset.
There is a storage bin at the rear of the Docking Station to store the VCI/OBD-II Cable when the handset is charging.
The LED state shall be as follows:
• Off indicates no power connected
• Green flashing indicates charging handset
• Green steady indicates charged handset
Note: LED shall flash momentarily even if the handset is completely charged when the handset is first attached to the charging station to indicate contact has been made.
12
MACTOOLS.COM
Battery Charging
Connect the handset to AC power and fully charge the battery.
ss02584
1
2
Power Port
1. Handset
2. AC Power cord
When the handset is turned on, the level of battery charge is indicated in the upper right corner of the screen.
NOTE: The tool can be used while charging. The battery can also be charged using the 18 volt power supply provided with the kit.
Using the handset
There are three options for use.
• Register Now: It is recommended to register for full functionality of tool and tech support.
• Trial Mode: This allows use of the handset for 30 days before it must be registered. If the 30 day trial period is over before it is registered, the handset functions will be locked out. At that time, registered mode or demo mode will need to be entered.
• Demo Mode: This mode demonstrates the functions by displaying random data.
ss02585
1. Press the power button to turn on the handset.
800.MACTOOLS
13
ss02386
You’ve got the right tool!
English Español French
2. Select a language.
REGISTRATION
It is important to register the handset right away. To register, it will need a Wi-Fi internet connection. To connect to Wi-Fi, refer to steps 2 through 6. Register now enables the unit. Register later causes the device to go into a
30-day trial mode. Demo Mode is for training and demonstration purposes only, it cannot communicate with a vehicle. Demo Mode will use sample data.
1. Select Register my Device Now.
2. Read and accept the user agreement.
ss02387
You’ve got the right tool!
Register my Device Now
Quick Setup
Register my Device Later
1) Read & agree to the EULA.
End User License Agreement
Software Product License Agreement
Copyright (c) 2014-2015, Bosch Automotive Service Solutions Inc. All
Rights Reserved
Demo Mode
2) Setup Wi-Fi.
SOFTWARE PRODUCT LICENSE AGREEMENT
3) Activate your warranty
IMPORTANT: Do not continue until you have read this Software
Product License Agreement (”Agreement”). By clicking the I Accept button (or authorizing any other person to do so), you accept this
Agreement and are bound by its terms. If you are not sure that you are authorized by your employer to accept this Agreement, take this package to a principal in your firm before proceeding. This Agreement is a legally binding document setting forth the manner by which you may use the Bosch Automotive Service Solutions Inc. (”Bosch”) software, and any associated media, printed materials and electronic documentation (collectively “Software Product”). Carefully read the terms and conditions of this Agreement before using this Software
Product. Use of this Software product indicates your acceptance of the following terms and conditions.
1. OWNERSHIP. The Software Product is licensed (not sold) to you.
The Software Product shall remain the property of Bosch. Bosch
I Agree
Note: Wi-Fi Must be ON. If Wi-Fi is OFF slide the Wi-Fi switch to the ON position and follow the prompts on the screen.
14
MACTOOLS.COM
ss02388
You’ve got the right tool!
Register my Device Now
Register my Device Later
Setup Wi-Fi
Add Wi-Fi Network
This is needed for networks that do not broadcast their SSID
Demo Mode
Wi-Fi is not enabled
Please enable Wi-Fi
OK
Wi-Fi OFF
3. Enable Wi-Fi and select Next ss02389
You’ve got the right tool!
Register my Device Now
Setup Wi-Fi
Add Wi-Fi Network
Register my Device Later This is needed for networks that do not broadcast their SSID
Demo Mode
Next: Your Name
Wi-Fi OFF
4. Select a network and select Next ss02390
You’ve got the right tool!
Register my Device Now
Setup Wi-Fi
Shop
Register my Device Later
Secured with WPA2
Demo Mode
Office
Secured with WPA2
Add Wi-Fi Network
This is needed for networks that do not broadcast their SSID
Next: Your Name
Wi-Fi ON
Next: Your Name
5. If a Network password is required the Android Wi-Fi screen will be displayed. Follow the prompts on the screen.
800.MACTOOLS
15
ss02391
Select Wi-Fi
On
Shop
Connected
Office
Saved
BACK NEXT
6. If an internet connection could not be established, follow the prompts on the screen and try again.
ss02392
You’ve got the right tool!
Setup Wi-Fi
Register my Device Now
Shop
Register my Device Later Secured with WPA2
Demo Mode
Office
Secured with WPA2
Internet Sync Required
Could not establish connection. Please ensure connection to
Internet is stable and try again!
OK
Wi-Fi ON
7. Enter your Name . Follow the prompts on the screen to activate warranty.
ss02393
You’ve got the right tool!
Register my Device Now
Activate Warranty
Register my Device Later
Demo Mode
John
Smith
City Service Center
City Service Center
Next: Your Name
Set Clock
8. Enter contact information. Follow the prompts on the screen.
Next: Contact Info
16
MACTOOLS.COM
ss02394
You’ve got the right tool!
Active Warranty
Register my Device Now [email protected]
Register my Device Later
3135551234
Demo Mode
1234 Main St.
Address 2 (optional)
Detroit MI
United States
492032
Confirm Info
9. Confirm information. Follow the prompts on the screen.
ss02395
You’ve got the right tool!
Active Warranty
Register my Device Now
Register my Device Later
John
Smith
Demo Mode
City Service Center
City Service Center
1/1/2016 [email protected]
3135551234
1234 Main St.
Detroit, MI 48202
United States
10. MDT 10 is ready to use.
ss02396
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
No Vehicle Selected
Maintenance Tests
All System DTC
Scan
Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
Activate Now
2:59
800.MACTOOLS
17
30 Day Trial
1. Select Register my Device Later for 30 days of full use of the tool before registration is required. If the handset is not registered within the 30 day trial period, after 30 days it will only function in Demo Mode.
ss02397
You’ve got the right tool!
Register my Device Now
Start a 30 Day Use
Register my Device Later
1) Read & agree to the EULA.
End User License Agreement
Software Product License Agreement
Copyright (c) 2014-2015, Bosch Automotive Service Solutions Inc. All
Rights Reserved
Demo Mode
2) Setup Wi-Fi.
SOFTWARE PRODUCT LICENSE AGREEMENT
Enabling 30 day use allows time to register. The tool can be used live on-car. At the end of the 30 days, only
Demo Mode will be available until the tool is registered.
IMPORTANT: Do not continue until you have read this Software
Product License Agreement (”Agreement”). By clicking the I Accept button (or authorizing any other person to do so), you accept this
Agreement and are bound by its terms. If you are not sure that you are authorized by your employer to accept this Agreement, take this package to a principal in your firm before proceeding. This Agreement is a legally binding document setting forth the manner by which you may use the Bosch Automotive Service Solutions Inc. (”Bosch”) software, and any associated media, printed materials and electronic documentation (collectively “Software Product”). Carefully read the terms and conditions of this Agreement before using this Software
Product. Use of this Software product indicates your acceptance of the following terms and conditions.
1. OWNERSHIP. The Software Product is licensed (not sold) to you.
The Software Product shall remain the property of Bosch. Bosch
I Agree
2. MDT 10 is ready to use.
ss02398
2:59
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
No Vehicle Selected
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
Demo
1. Select Demo mode ss02399
You’ve got the right tool!
Register my Device Now
Register my Device Later
Enter Demo Mode
1) Read & agree to the EULA.
End User License Agreement
Software Product License Agreement
Copyright (c) 2014-2015, Bosch Automotive Service Solutions Inc. All
Rights Reserved
Demo Mode
Demo Mode can be used for training and tool familiarization. You can select various vehicles and review the tool’s features and functions. Demo Mode does not allow communication to a car.
SOFTWARE PRODUCT LICENSE AGREEMENT
IMPORTANT: Do not continue until you have read this Software
Product License Agreement (”Agreement”). By clicking the I Accept button (or authorizing any other person to do so), you accept this
Agreement and are bound by its terms. If you are not sure that you are authorized by your employer to accept this Agreement, take this package to a principal in your firm before proceeding. This Agreement is a legally binding document setting forth the manner by which you may use the Bosch Automotive Service Solutions Inc. (”Bosch”) software, and any associated media, printed materials and electronic documentation (collectively “Software Product”). Carefully read the terms and conditions of this Agreement before using this Software
Product. Use of this Software product indicates your acceptance of the following terms and conditions.
1. OWNERSHIP. The Software Product is licensed (not sold) to you.
The Software Product shall remain the property of Bosch. Bosch
I Agree
18
MACTOOLS.COM
2. MDT 10 is ready to use.
ss02400
Demo
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
No Vehicle Selected
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
Provide Power to VCI
ss02590
2
2:59
1
VCI Cable Connections
1. VCI
2. OBDII/DLC cable
1. Connect the OBDII/DLC cable to the VCI.
2. Connect the OBDII/DLC cable to the DLC on vehicle (typically located on the driver’s side within 18 inches
(45.7 cm) of the steering wheel).
3. Turn ignition ON.
• Power indicator illuminates when the VCI is receiving power.
• PC connection illuminates when the VCI is connected to handset.
• Vehicle connection illuminates when the VCI is communicating with the handset and vehicle.
800.MACTOOLS
19
ss02591
2
1
3
VCI Connected to Vehicle
1. OBDII/DLC Cable
2. DLC
3. VCI
Manual Pairing
The first use will automatically pair.
1. Connect the VCI to the vehicle DLC.
2. Turn on handset and wait for it to display the home screen.
3. Select the VCI Connection Manager icon.
ss02401
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream
BMW
2013
BMW
335I (E92/E93)
xDrive3.0
TIRE PRESSURE
MONITOR
Maintenance Tests
All System DTC
Scan
Special Tests
Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
2:59
20
MACTOOLS.COM
VCI Connection Manager icon
VCI Connection Manager Icon Definitions
No VCI is paired with the handset.
VCI is paired on the hardware level, but software check had failed. VCI cannot be used without software update.
VCI is connected via Wi-Fi. Software check is successful, VCI is ready for use, but Wi-Fi signal is degraded.
VCI is connected via USB. Software check is successful, VCI is ready for use.
VCI is connected via Wi-Fi. Software check is successful, VCI is ready for use.
4. Once VCI Connection Manager icon is selected, VCI Connection Manager dialog is displayed, displaying discovered VCIs. Select Refresh to rediscover available VCIs if needed.
5. Select “Connect” next to desired VCI. VCI Connection Manager dialog will refresh to show successful connection.
ss02401
2:59
Active
Search Google for ...
CHECK
1001
101001
0101
Read DTCs Data Stream Special Tests
Diagnostic
Information
BMW
2013
BMW
335I (E92/E93)
xDrive3.0
TIRE PRESSURE
MONITOR
Maintenance Tests
All System DTC
Scan
Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
At this point the icon will change from “No VCI is paired with the handset” to VCI is connected via Wi-Fi
The handset is now paired to a VCI. To use a different VCI in the future, repeat the steps for manually pairing the VCI.
800.MACTOOLS
21
Restarting the tool:
ss02585
1. Press and release the power button.
ss02403
Active
No Vehicle Selected
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
Power off
Diagnostic Tool will shut down.
Maintenance Tests
All System DTC
Scan Browser
CANCEL OK
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
Settings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
2:59
2. Select OK. The tool will now shutdown and restart automatically.
When switching vehicles, it is best to return to the home screen before disconnecting the VCI from the vehicle to avoid communication errors.
Automatic Pairing
Automatic pairing will reconnect the last paired VCI to the handset during the start up process, as well as after unplugging and plugging the VCI back into an OBDII/DLC connector.
NOTE: After booting the handset, automatic pairing works immediately and ready when tool is booted. If it does not pair within a minute, repeat the manual VCI pairing procedure for that VCI. Typical connection time after
Connect to VCI message is displayed is 5-15 seconds. If this happens, reboot the handset and allow it to autopair. If it still fails to auto-pair then repeat the manual VCI pairing procedure.
VCI connection status icon will typically take 10-20 seconds to update after pairing the VCI to the handset.
When connection is lost, the VCI connection status Icon will typically take 10-20 seconds to update.
Cable connection
Connect the VCI OBDII/DLC cable into the vehicle. Using the Using the VCI Communication cable provided in the kit, plug the appropriate end (B) of the cable into the VCI, then the opposite end into a USB VCI port on the handset. VCI Connection Manger will switch icons to the USB icon.
22
MACTOOLS.COM
The same principle applies to switching vehicles as it did for wireless. Return to the home screen and then unplug and switch.
ss02592
2
3
4
1
Active
Search Google for ...
CHECK
Read DTCs
101001
0101
Data Stream
BMW
2013
BMW
Special Tests
OBD-II
Select Vehicle
Maintenance Tests
CHECK
Automated System
Test
All System DTC
Scan
Browser
Veiw Saved Tests View Data Stream
Recordings
Tue, 10 May 2016
Settings
2:59
USB Cable
1. OBDII/DLC Cable
2. DLC Connector
3. USB Cable
4. Handset
Wireless Range
The wireless internet capability of the tool is designed to communicate with the router when it is within a range of roughly 90 feet, depending on the shop environment, even though it is possible to go farther. Every shop has different noise that can interfere and hamper the distance of a wireless network, such as cordless phones, certain lighting, other wireless networks in the area, and other signals.
Test Startup and Vehicle Connection
1. Turn ON the handset.
2. Connect the OBDII/DLC cable to the VCI.
3. Connect the OBDII/DLC cable to the DLC on the vehicle.
4. Turn the ignition ON, but keep the engine OFF (KOEO).
5. Select vehicle from the Home screen.
6. Enter the vehicle information one of two ways:
• Auto ID
• Manual entry
7. From the home screen, select any diagnostic function.
Adjust Settings
Settings allow the user to make adjustments to the following:
• Applications
• Software information
• Software update
• Subscriptions
• User Detail
• Language
• Direct-Hit
800.MACTOOLS
23
ss02404
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
2:59
No Vehicle Selected
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
1. Select Settings from the home screen.
Application Settings
From the Settings screen select Application Settings. Follow the prompts on the screen to make changes to the following.
• Demo Mode
• Turn Demo mode ON or OFF
NOTE: Select/deselect demo mode can be switched from the home screen as well.
• Units of measure
• Switch between Standard or Metric
• Use TPR
• Enable TPR
• Data Stream Scroll Options
• Select scrolling options ss02405
Current
Settings
2005
Chevrolet
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Language
Direct-Hit®
Service
Demo Mode
Units of Measure
Use TPR
Data Stream Scroll Options
Standard
Ask during test
Always Ask
ON
24
MACTOOLS.COM
Software Information
From the Settings screen select Software Information. The current software versions will be displayed.
Select View Open Source Software Details to view more in-depth information.
ss02406
Current
Settings
2005
Chevrolet
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Language
Direct-Hit®
Service
CoreManager 2.5.0.98
Windows DBCoordinatorAPI 2.5.0.98
DBCoordinatorCore 2.5.0.98
Database Schema 61
Database Publication Date 2016-01-15
Diagnostic API WSI 2.6.2
Launcher Version 1.0.0.0
Serial Number 00HTOW0316000007OT
Release Version: 1.0.0.0
View Open Source Sofware Details Release Notes
Software Update
From the Settings screen select Software Update.
• Manually check for updates
• Set update strategy
• Automatic download
NOTE: Active internet connection is required for this function.
If an update is available follow the prompts on the screen to update the handset.
Installing the software can take up to 45 minutes depending on Wi-Fi connection speed and quality.
ss02405
Current
Settings
2005
Chevrolet
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Language
Direct-Hit®
Service
Demo Mode
Units of Measure
Use TPR
Data Stream Scroll Options
Standard
Ask during test
Always Ask
ON
800.MACTOOLS
25
Subscription
The tool must be registered to see this tab.
1. From the Settings screen select Subscription.
• Heavy duty vehicle function is locked and must be unlocked.
• Need to obtain subscription code.
• After one year, the user will be required to renew the subscriptions to receive product updates.
ss02408
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Langauge
Direct-Hit®
Service
All Coverage Subscription: Expires 3/9/2017
Enter Subscription Code Reload Subscriptions
2. Select Enter Subscription Code.
ss02409
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
Enter Subscription Code
All Coverage Subscription: Expires 3/9/2017
OK Cancel
q
1 a w
2 s e
3 d r
4 f
Z X C t
5 g
V y
6 h b u
7 n j
?123
,
3. Enter Subscription Code and select OK.
ss02410
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Langauge
Direct-Hit®
Service
All Coverage Subscription: Expires 3/9/2017
Subscription Successfully Activated
Enter Subscription Code Reload Subscriptions
i
8 k m o
9
!
l p
0
?
26
MACTOOLS.COM
User Details
1. From the Settings screen select User Details.
ss02411
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Langauge
Direct-Hit®
Service
Owner’s First Name
Owner’s Last Name
Distributor Name
Phone
Address 1
Address 2 (optional)
City
State/Province
Postal Code
Country
John
Smith
Dealership [email protected]
3135551234
1234 Main St
Detroit
Michigan
48235
United States
Save
2. Select field to modify.
ss02412
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
Z X
Owner’s First Name
Owner’s Last Name
Distributor Name
Phone q
1 a w
2 s e
3 d r
4 f
C
John
Smith
Dealership [email protected]
3135551234 t
5 g
V y
6 h b u
7 n j i
8 k m o
9
!
l p
0
?
?123
,
Note: The information saved in User Details will also update registration information.
!
800.MACTOOLS
27
Language
1. From the Settings screen select Language
2. Follow the prompts on the screen
• English
• Spanish
• French (when available) ss02413
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Langauge
Direct-Hit®
Service
English
Direct-Hit®
Identifix® Direct-Hit® provides:
• OEM specific information
• Wiring diagrams
• Technical Service Bulletins (TSBs)
• Diagnostic procedures
• Past reported fixes
Subscription is required to access Identifix®. To obtain username and password, select Identifix® link and subscribe.
1. From the Settings screen select Direct-Hit®
2. Follow the prompts on the screen ss02414
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Langauge
Direct-Hit®
Service
User Name
Password
Reset
Direct-Hit®
Save
28
MACTOOLS.COM
Service
1. From the Settings screen select Service
2. Select Restart Communications ss02415
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Langauge
Direct-Hit®
Service
3. Handset will Restart Communications ss02416
Current
Settings
2004
Subaru
Application Settings
Software Information
Software Update
Subscriptions
User Details
Contact Us
Langauge
Direct-Hit®
Service
Initializing Communication
Restart Communications
Restart Communications
800.MACTOOLS
29
GLOBAL OBDII APPLICATIONS
Overview
Global OBDII (also referred to as Generic OBDII) provides limited engine control and monitors the diagnostic control network of the vehicle. When a fault in the control network occurs, a DTC is recorded in the vehicle computer. This system is not vehicle specific so it is NOT necessary to select the vehicle to run a generic test.
NOTE: Global OBDII may be selected as a controller for a more specific General test.
Diagnostic Functions
ss02417
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
No Vehicle Selected
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
1. Select OBD-II from the home screen.
2. Follow the prompts on the screen.
Readiness Monitors
Mode 1 displays available monitor information.
The OBDII system has a series of systems that run self-tests. These systems or components have to be made ready by either turning on the ignition or manipulating the system in some other manner. This is called drive cycle.
Each system requires specific vehicle drive cycle and operating requirements to take place before the monitor self-check will run. OBDII systems require one monitor for current systems, or two monitors for older systems, are ready before testing can begin.
If the system is ready, no further action is required.
If the system is not ready, a drive cycle may need to be performed for that system.
Use the following procedure to verify the system is ready to be monitored.
30
MACTOOLS.COM
ss02418
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
Readiness (Mode 1)
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
Monitor Description
Catalyst Monitor
Misfire Monitor
2nd Air Monitor
Evaporative Emissions Monitor
Comprehensive Component Monitor
Fuel System Monitor
Heated Catalyst Monitor
A/C System Refrigerant Monitor
Status
Ready
Not Supported
Ready
Ready
Ready
Not Supported
Not Supported
Not Supported
Oxygen Sensor Monitor Ready
1. View the readiness table to verify system status.
• Ready: No further action is required.
• Not ready: Further action is required. Drive Cycle needs to be performed.
• Monitor not supported: Data is not supported on vehicle.
NOTE: A vehicle must be selected before diagnostic Information becomes available. Refer to diagnostic hub,
Start New Section.
Readiness Mode Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to more buttons.
View Help
Selecting View Help will open an online operators manual.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
800.MACTOOLS
31
Data Stream
Mode 1 views live vehicle sensor data.
The data stream function shows live sensor and solenoid data streaming from the vehicle’s ECU (electronic control unit).
ss02419
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
TAP ‘DATA STREAM MODE 1’ TO REOPEN
1. Select Data Stream Mode 1 from the Generic OBDII screen ss02420
Scroll Options
Please select how you would like to scroll between pages. This setting can also be changed from Settings tab
Touch here to use Vertical Scrolling
Touch here to use Horizontal Scrolling
32 seconds Checking for available data items. Please wait...
Don’t show this again
2. Select scrolling preference.
ss02421
Current
1001
101001
0101
Data Stream
for Global ODBII
Engine Coolant Temperature
Fuel Rail Pressure Gauge
Fuel Rail Pressure Relative To Manifold Vacuum
Catalyst Temperature Bank 1 Sensor 1
Catalyst Temperature Bank 1 Sensor 2
Ambient Air Temperature Degrees
Intake Air Temperature
Manifold Absolute Pressure
4251 °F
25.8 psi
89.6 psi
266 °F
3677 °F
1450 °F
4811 °F
263.84 inHg
A
Z
Distance Since DTC Clear
Distance MIL Active
Evaporative Emissions System Vapor Pressure
Catalyst Temperature Bank 2 Sensor 1
Catalyst Temperature Bank 2 Sensor 2
Vehicle Speed
Fuel Rail Pressure Gauge
Manifold Absolute Pressure
545 miles
618 miles
17.04 inH2O
2741 °F
4723 °F
867 mph
343.8 psi
62.92 inHg
51 / 200 frames
1 of 2
BUFFERING DATA..
3. Follow the prompts on the screen.
32
MACTOOLS.COM
A
Z
Data Stream Button Definitions
Enlarge Screen View Function
To view the data in the enlarge view, press the
Enlarge button.
Select Function:
1. Choose only the data you want to view by checking the box in front of each desired data item.
2. Select the Sort button.
Sort Function
• Select Sort to sort data items.
• Data may be sorted alphabetically, by graph, or by selection (checkbox checked).
• Sorting data items will reset the timeline frame counter, so sort these items before recording data. If sorting data while recording the recording will have a period of time where there is no data available.
Recording
• Select Recordings to view previously recorded data streams.
• Recordings are listed from newest to oldest.
When the folder is full, the newest recording pushes the oldest one out of the list.
Currently, there is no way to manually delete recordings.
• To view recordings, select the Recordings button near the top of the display.
• Select the desired recording.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to more buttons.
Erase All Recordings
800.MACTOOLS
Clear All Data
Select Clear Data to clear displayed data stream.
This function will reset the timeline frame counter and clear graphed data.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units
33
Data Stream Button Definitions
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
Freeze Frame
Mode 2 views data captured when a fault occurred. Freeze frame shows a data stream snapshot that was automatically recorded by the ECU when one or more DTCs occurred.
ss02422
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
Mode 2 Freeze Frames
Engine Coolant
Temperature
81
°F
Distance MIL Active
19894 miles
Barometric Pressure
7 inHg
Fuel Rail Pressure
Relative To Manifold
Vacuum
749.9 psi
Distance Since DTC Clear Fuel Rail Pressure Gauge
20657 miles
107.9 psi
Evaporative Emissions
System Vapor Pressure
-1762.05 iHg
Catalyst Temperature
Bank 1 Sensor 1
3317
°F
Catalyst Temperature
Bank 2 Sensor 1
Catalyst Temperature
Bank 1 Sensor 2
Catalyst Temperature
Bank 2 Sensor 2
8686
°F
7290
°F
671
°F
Freeze frame records each sensor’s current information at the time a DTC sets. This feature could be used when diagnosing an intermittent condition that requires certain conditions are met before the fault is active.
NOTE: DTCs are not always stored in Mode 2 freeze frame.
Freeze Frame Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to more buttons.
View Help
Selecting View Help will open an online operators manual.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
34
MACTOOLS.COM
DTCs Modes
Modes 3, 4, 7, and A read and clear DTCs.
ss02423
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
TAP ‘DTCs MODES 3, 4, 7, A’ TO REOPEN
1. Select DTCs Modes from the Generic OBDII screen ss02424
Current
CHECK
Diagnostic Trouble Codes
for Global OBDII
B0001
Driver Frontal Stage 1
Deployment Control (Subfault)
B0002
Driver Frontal Stage 2
Deployment Control (Subfault)
B0003
Driver Frontal Stage 3
Deployment Control (Subfault)
OBDII CURRENT CODES
B0003
Driver Frontal Stage 3
Deployment Control (Subfault)
OBDII PENDING CODES
OBDII CURRENT CODES
B0001
Driver Frontal Stage 1
Deployment Control (Subfault)
OBDII PERMANENT CODES
OBDII CURRENT CODES
B0002
Driver Frontal Stage 2
Deployment Control (Subfault)
OBDII PERMANENT CODES
B0001
Driver Frontal Stage 1
Deployment Control (Subfault)
B0002
Driver Frontal Stage 2
Deployment Control (Subfault)
OBDII PENDING CODES OBDII PENDING CODES
B0003
Driver Frontal Stage 3
Deployment Control (Subfault)
OBDII PERMANENT CODES
2. Use the buttons and follow the prompts on the screen.
800.MACTOOLS
35
OBDII DTC Nomenclature
ss01521
P-0102
Fault (00-99)
1 - Fuel & Air Metering
2 - Fuel & Air Metering (Injector Circuit)
3 - Ignition Systems or Misfire
4 - Auxilary Emission Control
5 - Vehicle Speed Control and
idle Control System
6 - Computer Output Circuit
7 - Transmission
8 - Transmission
0 - SAE
1 - MFG
B - Body
C - Chassis
P - Power Train
U - Network
Example: P0102 Mass Air Flow Performance
36
MACTOOLS.COM
DTCs Modes 3, 4, 5, A Button Definitions
Clear DTCs Button
The Clear DTCs button is used to clear codes and remove all but permanent DTCs on the selected controller. To clear codes, complete the following:
NOTE:
Clearing DTCs will erase current Mode 1 Readiness monitor information and require the user go through necessary drive cycles over again. So, if Mode 1 information needs to be reviewed, be sure to view it before clearing codes.
If a code will not clear, turn the ignition o for at least 10 seconds; turn it back on to KOEO, then retry. Some controllers will go to sleep after a period of inactivity and prevent clearing DTCs.
This key cycle may be needed when attempting to communicate with other controllers after a period of time on a different controller.
Refresh DTCs Button
Tapping the Refresh button initiates a fresh scan of DTCs from the vehicle.
Share DTCs Button
Tapping the Share button opens the app and initiates one of two options, share by email or
Bluetooth email concontaining a list of all the
DTCs set.
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to help content related to reading DTCs.
Note: an active internet connection will be required.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
800.MACTOOLS
37
Oxygen (O2) Sensors
Mode 5 views O2 sensor monitor test results.
ss02425
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
FREEZE FRAME MODE 2
Oxygen Sensor Tests (Mode 5)
Description
Bank 1 Sensor 1
Min Value Max Units
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
High Sensor Voltage For Switch Time Calculation
Lean To Rich Sensor Switch Time
Lean To Rich Sensor Threshold Voltage
Low Sensor Voltage For Switch Time Calculation
Maximum Sensor Voltage For Test Cycle
Minimum Sensor Voltage For Test Cycle
Rich To Lean Sensor Switch Time
0.000
0.000
0.000
0.000
0.000
0.000
0.000
0.003
0.002
0.003
0.003
0.003
0.003
0.002
1.275
1.020
1.275
1.275
1.275
1.275
1.020
V
V
V sec
V
V sec
Rich To Lean Sensor Threshold Voltage 0.000
0.003
1.275
V
Mode 5 displays the average of the O2 sensor monitor test results measured over a period of time. The parameters of this measurement vary between manufacturers. It may be necessary to run the vehicle for a period of time to allow the O2 sensors to fully warm up and begin operating as intended.
Oxygen (O2) Sensors Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to more buttons.
View Help
Selecting View Help will open an online operators manual.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
38
MACTOOLS.COM
Non-Continuous Tests
Mode 6 views onboard monitoring test results for noncontinuous monitor systems.
ss02425
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
Oxygen Sensor Tests (Mode 5)
Component parameters may not be valid if Readiness Status is ‘Not
Ready’.
CANCEL OK
1. Select Non-Continuous Tests from the Generic OBDII screen
2. Follow the prompts on the screen.
ss02427
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
Non-Continuously Monitored Tests
(Mode 6)
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
ECU: ENGINE
TID 1
CID 1
N/A
MIN
TID 1
TID 1
TID 2
CID 2
N/A
MIN
TID 2
TID 2
62038
VALUE
3776
MAX
Failed
N/A
UNITS
Passed
3073
VALUE
21587
MAX
N/A
UNITS
TID 3
CID 3
N/A
MIN
TID 3
TID 3
55785
VALUE
27062
MAX
Failed
N/A
UNITS
Non-Continuous Monitor Tests (Mode 6) are a pass/fail test. Some examples are certain EVAP tests, catalyst, and EGR. The following information is reported:
• ECU.
• TID (test identification) which indicates the system monitor.
• CID (component identification) which indicates the component tested and its test value.
• Minimum value, maximum value, and current value for each non-continuous monitor supported.
• Pass or fail test results.
Each vehicle manufacturer assigns a code number to their system monitors and components. Refer to the vehicle manufacturers Mode 6 code chart to determine the failure indicated by the TID and CID. If this chart is not available, run an automated system test (AST) from the DTC screen and select Mode 6. See Read DTCs section for more information regarding steps to complete that action.
800.MACTOOLS
39
Non-Continuous Tests Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to more buttons.
View Help
Selecting View Help will open an online operators manual.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
Special Tests
Mode 8 controls the operation of an onboard system, test, or component which is typically the EVAP system or diesel particulate filter (DPF) test.
ss02428
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
Vehicle Informationation (Mode 9)
TAP ‘SPECIAL TESTS MODE 8’ TO REOPEN
1. Select Special Tests from the Generic OBDII screen.
40
MACTOOLS.COM
ss02429
Current
SPECIAL TESTS
ALL TESTS
DPF TESTS
EVAP TESTS
All Special Tests
Search All Special Tests
DPF Tests
Diesel Particulate Filter Regeneration
EVAP Tests
Evaporative System Leak Check
When available, this selection will automatically take the user to the special test screen where the test group menu will be displayed. Make a selection to enter the test, then follow the on-screen prompts. Mode 8 will not be supported on all vehicles. If you wish to run an EVAP test on a vehicle that does not support Mode 8, enter vehicle specific mode and refer to the Special Tests section on how to run a special test.
Special Tests Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to more buttons.
View Help
Selecting View Help will open an online operators manual.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
800.MACTOOLS
41
Vehicle Info
Mode 9 views Vehicle Identification Numbers (VINs), calibration ID(s), and verification number(s).
ss02430
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
Vehicle Informationation (Mode 9)
Make sure the key is ON and the Engine is OFF.
CANCEL OK
1. Select Vehicle Info from the Generic OBDII screen.
2. Follow the prompts on the screen.
ss02431
Current
Generic OBDII
READINESS MODE 1
DATA STREAM MODE 1
Vehicle Informationation (Mode 9)
FREEZE FRAME MODE 2
DTC’s MODES 3,4,7,A
O2 SENSORS MODE 5
NON-CONTINUOUS TESTS
MODE 6
SPECIAL TESTS MODE 8
VEHICLE INFO MODE 9
Vehicle Identification Number
Controller
ENGINE
Calibration Identification Number
Controller
ENGINE
Calibration Verification Number
Controller
ENGINE
Counters
Vehicle Identification Number
1G6DM57N530102274
Calibration Identification Number
BOSCHA1037366956
Calibration Identification Number
4EF7033C
The 17 digit VIN provides information on the vehicle including year of manufacture, engine and possibly transmission type, vehicle body style, and color.
Mode 9 is not supported on older vehicles, so a visual check of the VIN through the windshield or on the door sticker would be required to obtain that VIN. Mode 9 is used on the tool to Auto ID the vehicle and for calibration verification to see if a newer calibration is available for re-flashing the ECU.
42
MACTOOLS.COM
Vehicle Info Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to more buttons.
View Help
Selecting View Help will open an online operators manual.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
800.MACTOOLS
43
SELECTING VEHICLE
WARNING
Before performing any diagnostic functions, refer to the Safety Precautions and the warnings provided by the vehicle manufacturer. In addition, follow any warnings and instructions provided on the handset.
Note: Select Demo to generate simulated data for demonstration purposes.
ss02432
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
No Vehicle Selected
Maintenance Tests
All System DTC
Scan
Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
1. Select, Select Vehicle to manually choose the vehicle, AutoID to automatically identify the vehicle or enter the VIN.
2. Select the vehicle specification options on each screen until the complete vehicle information is entered.
Auto ID
Auto ID uses the vehicle’s Mode 9 VIN information, when available. Most vehicles from 2004 and newer support Auto ID, but some other older vehicles may support Mode 9 too.
Auto ID Operation:
1. Handset must be on and and paired with the VCI which is connected to a vehicle.
ss02433
VEHICLE BAY
RECENT FAVORITES
SEARCH BY VIN
Enter New Vehicle
Start AutoID
2008 Chrysler
Crossfire
Limited 3.2
ENGINE
2015 Acura
ILX
Base 2.0
TRANSMISSION
1999 Chevrolet
C2500 2WD
LS 5.7
PCM
2003 Cadillac
CTS
Luxury Sport 3.2
ENGINE
?
OBD-II
Heavy Duty
Demo Mode ON
2. Select Start Auto ID
3. Once selected the handset will begin communicating with the vehicle.
44
MACTOOLS.COM
ss02434
VEHICLE BAY
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
RECENT FAVORITES
Start Auto ID
Make sure the key is ON and the Engine is OFF.
OK Cancel
SEARCH BY VIN
Demo Mode
ON
4. The vehicle must have the key on, engine off (KOEO).
ss02435
VEHICLE BAY
RECENT FAVORITES
Enter New Vehicle
Start AutoID
2006 Honda
Accord
EX 2.4
ENGINE
?
OBD-II
Heavy Duty
Reading OBDII Mode-9 VIN
SEARCH BY VIN
Demo Mode ON
5. Once the VIN is retrieved it is compared to the vehicle database.
6. If a match is found the vehicle selection information will be displayed on the screen.
7. Wait for Auto ID to finish ss02436
VEHICLE BAY
RECENT FAVORITES
VIN Match Results (3)
SEARCH BY VIN
1G6DM57N530102274
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
CADILLAC
2003 Cadillac
CTS
Luxury Sport
3.2, GAS,-, Naturally Aspirated, DOHC
CADILLAC
2003 Cadillac
CTS
Base
3.2, GAS,-, Naturally Aspirated, DOHC
CADILLAC
Demo Mode
ON
8. Select the desired vehicle from the list.
2003 Cadillac
CTS
Luxury
3.2, GAS,-, Naturally Aspirated, DOHC
800.MACTOOLS
45
ss02437
YEAR MAKE
MAINTENANCE
TESTS
ABS
CABIN COMP NODE
HEAT VENT A/C
MODEL SUBMODEL ENGINE CONTROLLER
ENGINE
WIRELESS CTRL
MODULE (TPMS)
DRIVERS DOOR
MODULE
HEATED SEAT
MODULE
GLOBAL OBDII
ELECTRONIC
SHIFTER
OCCUPANT
RESTRAINT
CONTROL
ELECTRIC
OVERHEAD
MODULE
FINAL DRIVE
CONTROL MODULE
FCM CENTRAL
GATEWAY
MEMORY SEAT
PASSENGER DOOR
MODULE
TRANSMISSION
AUDIO
HANDS FREE
MODULE
RADIO
Selected
2003 Cadillac
CTS (Base) 3.2 Gas
9. Select the desired vehicle controller.
ss02438
YEAR MAKE MODEL
MAINTENANCE
TESTS
AIRBAG (15)
AIR FUEL TANK
(58)
PARK ASSIST (76)
SUBMODEL ENGINE CONTROLLER
ENGINE (01) GLOBAL OBDII
ALL W
CD
CONVE
OEM Warnings
Improper installation of aftermarket radio or
Volkswagen/Audi radio not produced for use in 1998 model year and newer vehicles can cause severe damage to scan tools.
Is the vehicle equipped with this style radio
(if unsure select “Yes”)?
AUTO
TRANSMISSION
(02)
C (08)
ENTS
Yes
RA
No
STEM
Cancel
ABS (03)
AUTO ROOF (25)
NAVIGATION (37)
STEERING WHEEL
(16)
Selected
2003 Cadillac
CTS (Base) 3.2 Gas
10. OEM warnings or qualifiers may pop up. Answer appropriately.
SS02439
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
CADILLAC
2003
CADILLAC
CTS (Base)
3.2 Gas
ENGINE
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
Cancel
2:59
11. At this point vehicle entry will disappear and the user will be able to begin using diagnostic functions on the vehicle.
46
MACTOOLS.COM
Manual Entry
The handset must be turned on, be paired with the VCI which is connected to the vehicle and currently displaying the home screen. Once those conditions are met, complete the following: ss02432
2:59
Active
Search Google for ...
CHECK
1001
101001
0101
Read DTCs Data Stream Special Tests
Diagnostic
Information
No Vehicle Selected
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
1. Select “Select Vehicle” ss02440
VEHICLE BAY
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
RECENT
2008 Chrysler
Crossfire
Limited 3.2
ENGINE
FAVORITES
2015 Acura
ILX
Base 2.0
TRANSMISSION
1999 Chevrolet
C2500 2WD
LS 5.7
PCM
SEARCH BY VIN
2003 Cadillac
CTS
Luxury Sport 3.2
ENGINE
Demo Mode
ON
2. From the Vehicle Bay, select Enter New Vehicle.
ss02441
MODEL SUBMODEL ENGINE YEAR MAKE
To confirm via VIN, use the tenth digit
‘15
VIN F
‘14
VIN E
CONTROLLER
‘13
VIN D
‘10
VIN A
‘05
VIN 5
‘00
VIN Y
‘09
VIN 9
‘04
VIN 4
‘99
VIN X
‘08
VIN 8
‘03
VIN 3
‘98
VIN W
Selected
3. Select the model year of the vehicle.
800.MACTOOLS
‘12
VIN C
‘07
VIN 7
‘02
VIN 2
‘97
VIN V
‘11
VIN B
‘06
VIN 6
‘01
VIN 1
‘96
VIN T
Cancel
47
ss02442
YEAR MAKE
ACURA
MODEL SUBMODEL ENGINE CONTROLLER
ACURA ALFA ROMEO
CHEVROLET
FORD
CHRYSLER
GMC
DODGE
HONDA
INFINITI JEEP KIA
Selected
4. Select the make of vehicle.
ss02443
YEAR MAKE
2015
MODEL SUBMODEL ENGINE CONTROLLER
ILX MDX RDX
BUICK
FIAT
HONDA
LEXUS
RLX
CADILLAC
FORD
HYUNDAI
LEXUS
Cancel
TLX
2015 Acura
Selected
5. Select the model.
ss02444
YEAR MAKE MODEL SUBMODEL ENGINE CONTROLLER
BASE SH-AWD
Cancel
Selected
2015 Acura
MDX
6. Select the sub-model (trim level).
48
Cancel
MACTOOLS.COM
ss02445
YEAR MAKE
To confirm via VIN, use the digit
3.5, GAS, J35Y4,
Naturally Aspirated,
SOHC
VIN-
MODEL SUBMODEL
3.5, GAS, J35Y4,
Naturally Aspirated,
SOHC
VIN-
ENGINE CONTROLLER
Selected
2015 Acura
MDX Base
7. Select the engine.
Note: Some vehicles may not require this selection.
ss02446
YEAR MAKE MODEL SUBMODEL ENGINE CONTROLLER
MAINTENANCE
TESTS
ENGINE GLOBAL OBDII
ABS
WIRELESS CTRL
MODULE (TPMS)
CABIN COMP NODE
DRIVERS DOOR
MODULE
OCCUPANT
RESTRAINT
CONTROL
ELECTRIC
OVERHEAD
MODULE
ELECTRONIC
SHIFTER
FINAL DRIVE
CONTROL MODULE
FCM CENTRAL
GATEWAY
HEAT VENT A/C
HEATED SEAT
MODULE
MEMORY SEAT
PASSENGER DOOR
MODULE
Cancel
TRANSMISSION
AUDIO
HANDS FREE
MODULE
RADIO
Selected
2015 Acura
MDX (Base) 3.5 Gas
Cancel
8. Select the desired vehicle controller.
The following information may be necessary to identify the vehicle or inform the user of special conditions:
• Transmission type
• With or without TPMS
• ABS may be disabled during this test.
800.MACTOOLS
49
ss02447
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
ACURA
2015
ACURA
MDX (Base)
3.5 Gas
ENGINE
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
2:59
9. At this point vehicle entry will disappear and the user will be able to begin using diagnostic functions on the vehicle.
Recent
ss02432
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
2:59
No Vehicle Selected
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
1. Select, Select Vehicle.
50
MACTOOLS.COM
ss02448
VEHICLE BAY
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
RECENT
2008 Chrysler
Crossfire
Limited 3.2
ENGINE
FAVORITES
2015 Acura
ILX
Base 2.0
TRANSMISSION
1999 Chevrolet
C2500 2WD
LS 5.7
PCM
SEARCH BY VIN
2003 Cadillac
CTS
Luxury Sport 3.2
ENGINE
Demo Mode
ON
2. The Recent tab will show the most recent vehicles selected.
ss02449
VEHICLE BAY
RECENT FAVORITES
Enter New Vehicle
Start AutoID
2008 Chrysler
Crossfire
Limited 3.2
ENGINE
2015 Acura
ILX
Base 2.0
TRANSMISSION
1999 Chevrolet
C2500 2WD
LS 5.7
PCM
SEARCH BY VIN
2003 Cadillac
CTS
Luxury Sport 3.2
ENGINE
?
OBD-II
Set as current vehicle
Heavy Duty
Mark as favorite
Delete from recents
Demo Mode
ON
3. Press and hold a recent vehicle tile and select one of three choices:
• Set as current vehicle
• Mark as favorite
• Delete from recents
4. Select Set as current vehicle or just tap on the recent vehicle tile.
800.MACTOOLS
51
ss02450
YEAR MAKE
MAINTENANCE
TESTS
ABS
CABIN COMP NODE
HEAT VENT A/C
MODEL SUBMODEL ENGINE CONTROLLER
ENGINE
WIRELESS CTRL
MODULE (TPMS)
DRIVERS DOOR
MODULE
HEATED SEAT
MODULE
GLOBAL OBDII
ELECTRONIC
SHIFTER
OCCUPANT
RESTRAINT
CONTROL
ELECTRIC
OVERHEAD
MODULE
FINAL DRIVE
CONTROL MODULE
FCM CENTRAL
GATEWAY
MEMORY SEAT
PASSENGER DOOR
MODULE
TRANSMISSION
AUDIO
HANDS FREE
MODULE
RADIO
Selected
1999 Chevrolet
C2500 2WD LS 5.7
Cancel
5. Select the desired vehicle controller.
The following information may be necessary to identify the vehicle or inform the user of special conditions:
• Transmission type
• With or without TPMS
• ABS may be disabled during this test.
ss02451
2:59
Active
Search Google for ...
CHECK
1001
101001
0101
Read DTCs Data Stream Special Tests
Diagnostic
Information
CHEVROLET
1999
CHEVROLET
C2500 2WD
LS 5.7
ENGINE
Maintenance Tests
All System DTC
Scan Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
6. At this point vehicle entry will disappear and the user will be able to begin using diagnostic functions on the vehicle.
52
MACTOOLS.COM
Favorites
ss02432
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
No Vehicle Selected
Maintenance Tests
All System DTC
Scan
Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
1. Select, Select Vehicle.
ss02452
VEHICLE BAY
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
RECENT FAVORITES
2008 Chrysler
Crossfire
Limited 3.2
ENGINE
SEARCH BY VIN
2:59
Demo Mode
ON
2. Select Favorites tab.
ss02453
VEHICLE BAY
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
RECENT FAVORITES
2008 Chrysler
Crossfire
Limited 3.2
ENGINE
SEARCH BY VIN
3. Select a vehicle.
Demo Mode
ON
800.MACTOOLS
53
ss02454
YEAR MAKE
MAINTENANCE
TESTS
MODEL SUBMODEL ENGINE CONTROLLER
ENGINE GLOBAL OBDII
ABS
WIRELESS CTRL
MODULE (TPMS)
CABIN COMP NODE
DRIVERS DOOR
MODULE
OCCUPANT
RESTRAINT
CONTROL
ELECTRIC
OVERHEAD
MODULE
ELECTRONIC
SHIFTER
FINAL DRIVE
CONTROL MODULE
FCM CENTRAL
GATEWAY
HEAT VENT A/C
HEATED SEAT
MODULE
MEMORY SEAT
PASSENGER DOOR
MODULE
TRANSMISSION
AUDIO
HANDS FREE
MODULE
RADIO
Selected
2008 Chrysler
Crossfire limited 3.2
4. Select the desired vehicle controller.
The following information may be necessary to identify the vehicle or inform the user of special conditions:
• Transmission type
• With or without TPMS
• ABS may be disabled during this test.
ss02455
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
CHRYSLER
2008
CHRYSLER
Crossfire
Limited 3.2
ENGINE
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
Cancel
2:59
5. At this point vehicle entry will disappear and the user will be able to begin using diagnostic functions on the vehicle.
54
MACTOOLS.COM
OBD-II
ss02432
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
No Vehicle Selected
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
1. Select, Select Vehicle.
ss02456
VEHICLE BAY
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
RECENT FAVORITES
2008 Chrysler
Crossfire
Limited 3.2
ENGINE
SEARCH BY VIN
2:59
Demo Mode
ON
2. Select OBD-II
Note: For more information refer to the Global OBDII section.
800.MACTOOLS
55
Heavy Duty
ss02432
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Diagnostic
Information
No Vehicle Selected
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
1. Select, Select Vehicle.
ss02457
VEHICLE BAY
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
RECENT FAVORITES
2008 Chrysler
Crossfire
Limited 3.2
ENGINE
SEARCH BY VIN
2:59
Demo Mode
ON
2. Select Heavy Duty.
Note: You need to have a Heavy Duty subscription in order for Heavy Duty to be selectable.
ss02458
VEHICLE BAY
SEARCH BY VIN
Enter New Vehicle
RECENT FAVORITES
Select Cable
Looks lik
You can always use the
Vehicle Identification Number.
Start AutoID
?
OBD-II
3893-05
Heavy Duty
3825-30 3893-05 3825-35
Connect to Scan Tool
3825-29 3893-05 3825-35
Connect to Scan Tool
3. Select a Cable.
56
Demo Mode
ON
MACTOOLS.COM
ss02459
VEHICLE BAY
Enter New Vehicle
Start AutoID
?
OBD-II
Heavy Duty
RECENT FAVORITES
Select Option
Looks lik
Engine J1939
Engine MID 128 J1587/1708
Transmission MID: 130 J1587/1708
Brake MID: 136 J1587/1708
Instrument Cluster MID: 140 J1587/1708
Vehicle Management MID: 142 J1587/1708
Fuel System MID: 143 J1587/1708
Cruise Control MID: 144 J1587/1708
Cab Climate MID: 146 J1587/1708
Particulate MID: 177 J1587/1708
4. Select a controller.
Demo Mode ss02460
ON
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
SEARCH BY VIN
You can always use the
Vehicle Identification Number.
Diagnostic
Information
2:59
Heavy Duty
HEAVY DUTY
Engine MID 128
J1587/1708
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Settings
System Wiring
Diagrams
5. At this point vehicle entry will disappear and the user will be able to begin using diagnostic functions on the vehicle.
Note: Special Test, Diagnostic Information, Maintenance Tests, All System DTC Scan, Atuomated System Test are not available.
800.MACTOOLS
57
J1587/1708 DTC Nomenclature
MID - Message Identification
The MID Identifies the Component
Example: MID 128 = Engine
MID 130 = Transmission
MID 136 = Brakes (ABS)
PID - Parameter Identification
The PID Identifies the data from a components electrical parts
Example: PID 084 = Road Speed (MPH)
PID 100 = Engine Oil Pressure (PSI)
PID 177 = Transmission Oil Temperature (Degrees)
SID - Subsystem or Status Identification
The SID identifies the status of a components electrical part
Example: SID 001 = Injector Cylinder #1 (on/off)
SID 034 = Reverse Switch (Open/Closed)
SID 163 = Transmission Range (HI/LO)
Note: MID related SID’s start with Number 1 and sequentially increase. Common SID’s start at Number 255 and sequentially increase.
FMI - Failure Mode Identifier
The FMI describes the type of failure detected in the part identified by the PID or SID. The FMI, and either the
PID or SID combined to form a given diagnostic Fault code.
Example: FMI 002 = Data erratic, Intermittent or incorrect
FMI 005 = Current below normal or Open circuit
FMI 007 = Mechanical System Not Responding
FMI 011 = Failure Mode not Identifiable
Normal Message
MID-PID/SID-FMI or
128-084-002
128 = Engine
084 = Vehicle Speed Sensor
002 = Data erratic, Intermittent or incorrect
Example: The Vehicle speed sensor circuit is bad.
58
MACTOOLS.COM
J1939 DTC Nomenclature
SA - Source Address
The SA field contains the ECU that is sending the message
Example: SA 0 = Engine
SA 3 = Transmission
SA 11 = Brakes System Controller
SPN - Suspect Parameter Number
The SPN is used to identify the item for which diagnostics are being reported
Example: SPN 156 = Injector Timing Rail 1 Pressure
SPN 031 = Transmission Range Position
SPN 639 = J1939 Network
FMI - Failure Mode Identifier
The FMI describes the type of failure detected in the part identified by the SPN. The FMI, and either the SPN combined to form a given diagnostic Fault code.
Example: FMI 002 = Data erratic, Intermittent or incorrect
FMI 005 = Current below normal or Open circuit
FMI 007 = Mechanical System Not Responding
FMI 011 = Failure Mode not Identifiable
Normal Message
SA/SPN/FMI or
3-639-02
03 = Transmission
639 = J1939
002 = Data erratic, Intermittent or incorrect
Example: The Transmission has detected the J1939 network has an error.
800.MACTOOLS
59
READ DTCS
Overview
The Read DTCs function allows reading, clearing, printing, and sharing (wireless or email) of vehicle DTCs.
Onboard Code Assist information may also be available, for selection when DTCs are found. This information contains pertinent details regarding the selected DTC. For more detailed comprehensive information, go to
Service and Settings, Direct-Hit® to subscribe.
Vehicle must be selected from the Vehicle Bay and the handset must now be displaying the Home Screen.
ss02461
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan
Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select Read DTCs from the home screen.
ss02462
Current
Diagnostic Trouble Codes
2007
Jeep
B1000
A/C Switch Request Input
Circuit/Performance
0
B1001
A/C Switch Request Input
Circuit Low
0
B1002
A/C Switch Request Input
Circuit High
0
B1000
A/C Switch Request Input
Circuit/Performance
0
Active
B1001
A/C Switch Request Input
Circuit Low
0
Active
B1002
A/C Switch Request Input
Circuit High
0
Active
B1000
A/C Switch Request Input
Circuit/Performance
0
Pending
B1001
A/C Switch Request Input
Circuit Low
0
Pending
B1002
A/C Switch Request Input
Circuit High
0
Pending Stored Stored
2. Codes will be read from the selected controller and displayed on the screen.
60
MACTOOLS.COM
800.MACTOOLS
Read DTCs Button Definitions
Ford/Lincoln/Mercury
Self Diagnostics button displays a pop up menu allowing the user to choose between specific special tests.
GM/GMC
Status button displays a pop up menu allowing the user to view the status on DTCs
Clear DTCs Button
The Clear DTCs button is used to clear codes and remove all but permanent DTCs on the selected controller. To clear codes, complete the following:
NOTE:
Clearing DTCs will erase current Mode 1 Readiness monitor information and require the user go through necessary drive cycles over again. So, if Mode 1 information needs to be reviewed, be sure to view it before clearing codes.
If a code will not clear, turn the ignition o for at least 10 seconds; turn it back on to KOEO, then retry. Some controllers will go to sleep after a period of inactivity and prevent clearing DTCs.
This key cycle may be needed when attempting to communicate with other controllers after a period of time on a different controller.
Refresh DTCs Button
Tapping the Refresh button initiates a fresh scan of DTCs from the vehicle.
Share DTCs Button
Tapping the Share button opens the app and initiates one of two options, share by email or
Bluetooth email concontaining a list of all the
DTCs set.
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to help content related to reading DTCs.
Note: an active internet connection will be required.
View Help
Selecting View Help will open an online operators manual.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
61
Ford/Lincoln/Mercury
When connected to a Ford/Lincoln/Mercury vehicle a pop up menu allowing the user to choose between specific special tests.
ss02463
2:59
Active
Search Google for ...
CHECK
1001
101001
0101
Read DTCs Data Stream Special Tests
Diagnostic
Information
Ford
2012
Ford
Mustang
Shelby GT500
PCM
Maintenance Tests
All System DTC
Scan Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select Read DTCs from the home screen.
ss02464
Current
Diagnostic Trouble Codes
2012
Ford
Select Option
Read DTCs
KOEO
KOER
Reset KAM
2. Tapping an option in the menu takes the user to that test. Follow the prompts on the screen.
ss02465
Current
Diagnostic Trouble Codes
2003
Ford
B1213
Less Than Two Keys
Programmed To PATS
4
B1219
Fuel Tank Press Sens Circuit
0
B1220
Fuel Tank Press Sens Circuit
Open
0
Current Codes Current Codes Current Codes
3. Codes will be read from the selected controller and displayed on the screen.
62
MACTOOLS.COM
GM/GMC
When connected to a GM/GMC vehicle a pop up menu appears, allowing the user to choose between specific special tests.
ss02466
2:59
Active
Search Google for ...
CHECK
1001
101001
0101
Read DTCs Data Stream Special Tests
Diagnostic
Information
Chevrolet
2009
Chevrolet
Malibu
LS2.4
Engine
Maintenance Tests
All System DTC
Scan
Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select Read DTCs from the home screen.
ss02467
Current
2009
Chevrolet
CHECK
Diagnostic Trouble Codes
Press DTC for Repair information
Select Option
Read DTCs
Check DTC Status
Failure Records
Status Clear Read Share Menu
2. Tapping an option in the menu takes the user to that test. Follow the prompts on the screen.
ss02468
Current
Diagnostic Trouble Codes
GM
2009
Chevrolet
P0016
Crankshaft position (CKP)-
Camshaft Position (CMP)
0
P0101
MAF Sensor Performance
12
P0102
MAF Sensor Circuit Low
Frequency
7
P0016
Crankshaft position (CKP)-
Camshaft Position (CMP)
0
Fail Since Clear
P0101
MAF Sensor Performance
12
Fail Since Clear
P0102
MAF Sensor Circuit Low
Frequency
7
Fail Since Clear
P0016
Crankshaft position (CKP)-
Camshaft Position (CMP)
0
MIL Codes
P0101
MAF Sensor Performance
12
MIL Codes
P0102
MAF Sensor Circuit Low
Frequency
7
MIL Codes
P0016
Crankshaft position (CKP)-
Camshaft Position (CMP)
0
History Codes
P0101
MAF Sensor Performance
12
History Codes
P0102
MAF Sensor Circuit Low
Frequency
7
3. Codes will be read from the selected controller and displayed on the screen.
800.MACTOOLS
63
Manual DTCs
Certain vehicles do not support standard DTC protocol and will require a manual process for retrieving and clearing codes.
ss02469
Current
CHECK
Diagnostic Trouble Codes
2002
Subrau
1) Take out diagnosis connector from side of drive’s seat heater unit.
2) Turn ignition switch Off.
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in order of
1. Follow the prompts on the screen for retreiving DTCs.
ss02470
Current
CHECK
Diagnostic Trouble Codes
2002
Subrau
1) Take out diagnosis connector from side of drive’s seat heater unit.
2) Turn ignition switch Off.
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in order of
2. Select Diagnostic Trouble Codes button.
ss02471
Current
2002
Subrau
CHECK
11
Start Code: Trouble Code Is Shown
After Start Code Only Start Code Is
2) Turn ignition switch Off.
21 Abnormal ABS Sensor (Open Circuit
Or Input Voltage Too High) - Front
Right ABS Sensor
4) Turn ignition switch On.
22 Abnormal ABS Sensor (Abnormal
ABS Sensor Signal) - Front Right ABS
Sensor
23
Abnormal ABS Sensor (Open Circuit
These repeat for a maximum
24 Abnormal ABS Sensor (Abnormal
ABS Sensor Signal) - Front Left ABS
Sensor
7) NOTE: When there are no 25
8) When on-board diagnosis stored in the EEPROM as a
(Stored codes will stay in me
Abnormal ABS Sensor (Open Circuit
Or Input Voltage Too High) - Rear
Right ABS Sensor
Close de (11) is shown.
n (up to a maximum of three) will be e, the most recent three will be stored.
3. Follow the prompts on the screen.
64
MACTOOLS.COM
ss02472
Current
CHECK
Diagnostic Trouble Codes
2002
Subrau
1) Take out diagnosis connector from side of drive’s seat heater unit.
2) Turn ignition switch Off.
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in order of
4. Select Clear DTCs button.
ss02473
Current
CHECK
Diagnostic Trouble Codes
2002
Subaru
1) After calling up a diagnostic trouble code (DTC), disconnect diagnosis connector terminal 6 from diagnosis terminal.
2) Repeat 3 times within approx. 12 seconds; connecting and disconnecting terminal 6 and diagnosis terminal for at least 0.2
seconds each time.
3) NOTE: After diagnostics is completed, make sure to clear memory. Make sure only start code (11) is shown after memory is cleared.
5. Follow the prompts on the screen.
Code Criteria
Codes will be read from the selected controller and displayed on the screen.
ss02474
Current
Diagnostic Trouble Codes
2003
GMC
P0016
Crankshaft position (CKP)-
Camshaft Position (CMP)
0
P0101
MAF Sensor Performance
12
P0102
MAF Sensor Circuit Low
Frequency
7
P0016
Crankshaft position (CKP)-
Camshaft Position (CMP)
0
Fail Since Clear
P0101
MAF Sensor Performance
12
Fail Since Clear
P0102
MAF Sensor Circuit Low
Frequency
7
Fail Since Clear
P0016
Crankshaft position (CKP)-
Camshaft Position (CMP)
0
MIL Codes
P0101
MAF Sensor Performance
12
MIL Codes
P0102
MAF Sensor Circuit Low
Frequency
7
MIL Codes
P0016
Crankshaft position (CKP)-
Camshaft Position (CMP)
0
History Codes
P0101
MAF Sensor Performance
12
History Codes
P0102
MAF Sensor Circuit Low
Frequency
7
If a DTC has code criteria available there will be an indication in the upper right corner of the listed DTC.
800.MACTOOLS
65
ss02475
Current
2008
Ford
B1213
Less Than Two Keys Programmed To Passive Anti-Theft System
DESCRIPTION
Code Assist
Code Criteria
Description Element
CODE ASSIST
Frequently Reported Fixes Ignition Key(s)
PCM Pin
Frequently Reported Fixes Vehicle Theft Deterrent (VTD)
System Learn Procedure
LOCATION
SCAN TEST
Diagram
WAVEFORM
TSB REFERENCE
Action
Replaced
Performed
Repair Hotline
800.288.6210
5
SYSTEM WIRING
DIAGRAMS
Connector
DTC Info
DTC Info allows the technician to find details related to a given DTC.
Description
Displays the description associated with the selected DTC.
Code Criteria
Provides information regarding how the DTC is set.
Code Assist
Provides information regarding the kind of action other technicians found successful when faced with the same
DTC.
PCM Pin
Provides detailed information related to the actual pins on the PCM that are associated with the selected DTC.
Location
Aids the technician in determining where on the vehicle their attention should be directed.
Scan Test
Provides the technician with detailed test steps.
Diagram
Provides a circuit diagram related to the selected DTC.
Waveform
Presents reference waveform information to help the technician understand and fix the problem.
TSB Reference
Provides the technician with TSBs associated with the selected DTC.
Connector
Presents information related to the connector to help the technician understand and fix the problem.
Identifix® Direct-Hit®
A subscription is required to access Identifix® Direct Hit®. To obtain a username and password, go to www.
identifix.com and fill out the necessary steps to acquire an account.
Once account is setup with Identifix®:
• Select Settings button from the Home screen.
• Select Direct-Hit® from the available tabs on the left margin of the screen.
66
MACTOOLS.COM
• Input the username and password acquired from Identifix® by selecting the empty field.
• Using the virtual keyboard enter the required information for both fields.
• Select GO.
800.MACTOOLS
67
DATA STREAM
Overview
The data stream function shows live sensor and solenoid data streaming from the vehicle ECU (electronic control unit). Connect the VCI with the vehicle at key on engine off or key on engine running to see live dynamic data, instead of static live data. Each data item has a selection checkbox and a display format menu.
Basic Data Stream Procedure
ss02476
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
BMW
2013
BMW
335I (E92/E93)
xDrive3.0
TIRE PRESSURE
MONITOR
Maintenance Tests
All System DTC
Scan Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. From the home screen, select Data Stream.
2. If the vehicle is NOT a Volkswagen/Audi then go to step 5.
ss02477
Current
1001
101001
0101
Data Stream
2008
Audi
All Data Groups
Volkswagen/Audi Group
System Status
All Data Groups
Search all Data Streams
Volkswagen/Audi Group Select
Ignition
System Status Select Customize
Knock Control
Ignition
Select Customize
Lambda/Catalytic
Knock Control
Select Customize
Engine Speed/Idle
Lamdba/Catalytic
Select Customize
Throttle Valve
Exhaust Reduction
Engine Speed/Idle Select Customize
Control Module identification
Throttle Valve Select Customize
Special 86-89
Select
3. Follow the prompts on the screen. Select or customize a group.
Data Groups
• Data groups may be selected at any time within data stream.
• Select the data group menu button from the top of the screen.
• Scroll through the menu until the desired data group is found, then select it.
Note: It is possible to change controllers while in data stream.
• Select the controller selection button.
• Select the desired controller.
• Once controller is selected, select the data group menu button.
• Select the desired data group.
Customize
68
MACTOOLS.COM
ss02478
Current
1001
101001
0101
Data Stream
2003
Cadillac All Data Groups
Volkswagen/Audi Group
System Status
Volkswagen/Audi Group
System Status
Enter a Group Between: 0 and 255
Cancel OK
Ignition
System Status
Knock Control
-
*
( )
/
+
Ignition
.
,
=
*
7
4
1 2
5
8
0
4. Select the Volkswagen/Audi Group. When finished go to Step 6.
ss02479
3
6
9
#
Select
Select
Select
Customize
Customize
Customize
Current
1001
101001
0101
Data Stream
2003
Cadillac
All Data Groups
All Data Groups
Search all Data Streams
All Data Items
EVAP Data
Engine Data 1
Engine Data 2
All Data Items
* Clutch Start Switch (If Equipped)
* PNP Switch (If Equipped)
A/C High Side Pressure Sensor
A/C Pressure Disable
A/C Relay Command
Acceleration Pedal Position At Idle
Accelerator Pedal Position Sensor 1 Voltage
Select
* Cruise Clutch Switch (If Equipped)
A/C High Side Pressure
A/C Off For Wide Open Throttle
A/C Relay
A/C Request
Accelerator Pedal Position Angle
Accelerator Pedal Position Sensor 2 Voltage
Customize
Engine Data 3
Fuel Trim Data
Misfire Data
TAC Data
EVAP Data
Accelerator Pedal Position Angle
Calculated BARO
Engine Coolant Temperature
Engine Speed
Evaporative Emissions Vent Solenoid
Fuel Level Sensor Left Tank
Fuel Tank Pressure
Engine Data 1
Select
Battery Voltage
Desired Idle Speed
Engine Run Time
Evaporative Emissions Canister Purge
Fuel Level
Fuel Level Sensor Right Tank
Fuel Tank Pressure Sensor
Select
5. Follow the prompts on the screen. Select or Customize a group.
Data Groups
• Data groups may be selected at any time within data stream.
• Select the data group menu button from the top of the screen.
• Scroll through the menu until the desired data group is found, then select it.
Note: It is possible to change controllers while in data stream.
• Select the controller selection button.
• Select the desired controller.
• Once controller is selected, select the data group menu button.
• Select the desired data group.
Customize
Customize
800.MACTOOLS
69
ss02480
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed
Engine Coolant Temperature
Mileage Since DTC Cleared
Mileage Since MIL Request
A/C High Side Pressure
Startup Engine Coolant Temperature
Mass Air Flow
Evaporative Emissions Canister Purge
12 mph
68 °F
37900 miles
31075 miles
433 psi
34 °F
171.90 g/s
63 %
Intake Air Temperature
Fuel Tank Pressure
Calculated converter Temperature
Fuel Level
Calculated BARO
Start Up Intake Air Temperature
Ignition 1
Spark Advance
A
Z
139 / 200 frames
1 of 2
BUFFERING DATA...
6. Follow the prompts on the screen.
ss02481
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed
Intake Air Temperature
104
2
293
-24
Engine Coolant
Temperature
Fuel Tank Pressure
11.0
-6.3
415
93
Mileage Since DTC
Cleared
125792 miles
22817
Low
84647
Avg
Calculated Converter
Temperature
148941
High
2169
59
A
Z
Mileage Since MIL
Request
12277
Low
Fuel Level
26670
Avg
30054 miles
40498
High
5.05
Low
14.92
Avg
18.31
gal
22.32
High
111 °F
-5.7 inH2O
574 °F
13.61 gal
8 psi
217 °F
13.3 V
-10.8°
55 / 200 frames
1 of 4
BUFFERING DATA...
7. The selected data will be displayed.
Enlarge Screen View Function
1. Enhanced data stream provides OEM specific information.
ss02482
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed Engine Coolant
Temperature
Mileage Since DTC
Cleared
104 415
Intake Air Temperature
2
Fuel Tank Pressure
93
125792 miles
22817
Low
84647
Avg
Calculated Converter
Temperature
148941
High
293 11.0
2169
-24 -6.3
59
A
Z
Mileage Since MIL
Request
12277
Low
Fuel Level
26670
Avg
30054 miles
40498
High
5.05
Low
14.92
Avg
18.31
gal
22.32
High
55 / 200 frames
1 of 4
BUFFERING DATA...
To view the data in the Enlarge view, press the Enlarge button.
70
MACTOOLS.COM
ss02483
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed
158
66 mph
3
Intake Air Temperature
A
Z
1
419
277
°F
-20
BUFFERING DATA...
190 / 200 frames
1 of 15
Note: The far left 2-data tiles will be enlarged to select the specific data tiles to be enlarged.
To see more graphs use your finger to swipe the screen.
Note: Depending on your Scroll Options preference either horizontally or vertically.
Data Stream View Button Definitions
Reduce View Function
To Zoom Out, press the Reduce View button.
Enlarge View Function
To view the data in the enlarge view, press the
Enlarge View button.
Zoom Out Function
To Zoom Out, press the Zoom Out button.
Zoom In Function
To view the data in the Full Screen Mode, press the Zoom In button.
800.MACTOOLS
71
Full Screen View Function
To view the data full screen, press Full Screen button.
ss02484
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed
158
66 mph
3
Intake Air Temperature
A
Z
1
419
277
°F
-20
190 / 200 frames
1 of 15
BUFFERING DATA...
To view the data in Full Screen view, press the Zoom In button.
ss02485
Vehicle Speed
155
142 mph
1
BUFFERING DATA...
Note: The top right graph will be shown full size.
To see more graphs use your finger to swipe the screen.
Note: Depending on your Scroll Options preference either horizontally or vertically.
44 / 200 frames
1 of 30
72
MACTOOLS.COM
Display Types
To change data item display types, select the data item menu button located in upper right ss02488
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed Engine Coolant
Temperature
Mileage Since DTC
Cleared
A
Z
Mileage Since MIL
Request
104 415
Intake Air Temperature
2
293
237
°F
-24
Fuel Tank Pressure
93
11.0
8.1
inH2O
-6.3
125792 miles
22817
Low
84647
Avg
Calculated Converter
Temperature
148941
High
2169
1994
°F
59
12277
Low
Fuel Level
26670
Avg
30054 miles
40498
High
5.05
Low
14.92
Avg
18.31
gal
22.32
High
55 / 200 frames
1 of 4
##
BUFFERING DATA...
Display Type Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to more buttons.
Digital
To change to digital form, select the ## Digital button.
Line Graph
To change to line graph, select the Line Graph button.
Bar Graph
To change to bar graph, select the Bar Graph button.
Change Color
To change the color of a graph, select the
Change Color button.
Clear All Data
Select Clear Data to clear displayed data stream.
This function will reset the timeline frame counter and clear graphed data.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
Use Metric Units
Selecting Metric Units will switch from English/
Standard Units to Metric Units.
800.MACTOOLS
73
Display Type Button Definitions
Use English/Standard Units
Selecting English/Standard Units will switch from Metric Units to English/Standard Units.
NOTE: Not all display types are available for all data items
Select Function
ss02489
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed Engine Coolant
Temperature
Mileage Since DTC
Cleared
104 415
Intake Air Temperature
2
293
Fuel Tank Pressure
93
11.0
125792 miles
22817
Low
84647
Avg
Calculated Converter
Temperature
148941
High
2169
-24 -6.3
59
A
Z
Mileage Since MIL
Request
12277
Low
Fuel Level
26670
Avg
30054 miles
40498
High
5.05
Low
14.92
Avg
18.31
gal
22.32
High
55 / 200 frames
1 of 4
1. Select the Select button.
ss02490
BUFFERING DATA...
Current
1001
101001
0101
Data Stream
All Data Items
A
Z
Clear Selection
A
Z
2
2003
Cadillac
Vehicle Speed
Vehicle Speed Intake Air Temperature
102 °F
Engine Coolant Temperature
Mileage Since DTC Cleared
Mileage Since MIL Request
Engine Coolant
Temperature
Mileage Since DTC
Cleared
Mileage Since MIL
Request
Fuel Tank Pressure
Calculated Converter
Temperature
Fuel Level perature
3.0 inH2O
855 °F
17.62 gal
A/C High Side Pressure
7 psi
A/C High Side Pressure Calculated BARO
Startup Engine Coolant Tempera rature
167 °F
Mass Air Flow
Startup Engine Coolant
Temperature
Start Up Intake Air
Temperature
2.0 V
Evaporative Emissions Canister R
Mass Air Flow Ignition 1
-46.5°
Evaporative Emissions
Canister Purge
0 / 30 items selected (Unfiltered)
Spark Advance
Close Apply
BUFFERING DATA...
139 / 200 frames
1 of 1
2. Choose only the data you want to view by checking the box in front of each desired data item.
3. Select apply
74
MACTOOLS.COM
Sort Function
ss02491
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed
Intake Air Temperature
158
95
378
160
Engine Coolant
Temperature
Fuel Tank Pressure
289
32
-0.3
-11.7
Mileage Since DTC
Cleared
610
Low
63042
Avg
67667 miles
157372
High
A
Z
2
BUFFERING DATA...
1. Select Sort to sort data items.
ss02492
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed
Intake Air Temperature
147
2
415
-38
Engine Coolant
Temperature
Mileage Since DTC
Cleared
415
View All
Fuel Tank Pressure
Sort By Alpha
67
Low
Sort By Graph
3.6
60960 miles
126873
Avg
201412
High
-12.8
A
Z
2
22 / 200 frames
1 of 1
BUFFERING DATA...
200 / 200 frames
1 of 1
2. Data may be sorted alphabetically, by graph, or by selection (checkbox checked).
Note: Sorting data items will reset the timeline frame counter, so sort these items before recording data. If sorting data while recording the recording will have a period of time where there is no data available.
800.MACTOOLS
75
Recording
ss02493
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed
Intake Air Temperature
104
2
293
-24
Engine Coolant
Temperature
Fuel Tank Pressure
11.0
-6.3
415
93
Mileage Since DTC
Cleared
125792 miles
22817
Low
84647
Avg
Calculated Converter
Temperature
148941
High
2169
59
A
Z
Mileage Since MIL
Request
12277
Low
Fuel Level
26670
Avg
30054 miles
40498
High
5.05
Low
14.92
Avg
18.31
gal
22.32
High
-36 -4.3
-54
10.59
Low
55 / 200 frames
1 of 4
BUFFERING DATA...
1. Select the red record button located at the bottom left of screen.
• When recording the red record button will turn into a check mark.
ss02494
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed Engine Coolant
Temperature
Mileage Since DTC
Cleared
205
123 mph
32
Low
92
Avg
Intake Air Temperature
140
High
Fuel Tank Pressure
-35
103443 miles
7855
Low
60040
Avg
Calculated Converter
Temperature
103443
High
261 12.5
1832
A
Z
Mileage Since MIL
Request
1
19767
Low
Fuel Level
33031
Avg
30062 miles
39942
High
19.98
Avg
17.89
gal
26.68
High
RECORDING LIVE DATA..
2. To stop recording select the check mark
Recordings
ss02495
Current
2003
Cadillac
1001
101001
0101
Data Stream
All Data Items
Vehicle Speed Engine Coolant
Temperature
Intake Air Temperature
142
1
415
-26
414
RECORDINGS
36
23 minutes ago
ENGINE
2003 Cadillac CTS Luxury Sport
Yesterday @ 7:29 pm
ENGINE
3.6
11.9
-12.7
Mileage Since DTC
Cleared
7855
Low 188 frames
5
160150 miles
202720
High
266 frames
A
Z
2
57 frames
1 of 4
BUFFERING DATA...
200 / 200 frames
1 of 1
1. Select Recordings to view previously recorded data streams.
• Recordings are listed from newest to oldest. When the folder is full, the newest recording pushes the
76
MACTOOLS.COM
oldest one out of the list. Currently, there is no way to manually delete recordings.
• To view recordings, select the Recordings button near the top of the display.
2. Select the desired recording.
Playback Instructions
ss02496
Current
1001
101001
0101
Recorded Data Stream
2003 Cadillac CTS Luxury Sport ENGINE
Vehicle Speed Engine Coolant
Temperature
88 205
Mileage Since DTC
Cleared
A
Z
Mileage Since MIL
Request
2
Intake Air Temperature
32
126
Fuel Tank Pressure
36
3.6
40622 miles
7855
Low
41578
Avg
Calculated Converter
Temperature
79187
High
1011
30762
Low
Fuel Level
36191
Avg
35592 miles
39732
High
-36 -4.3
-54
10.59
Low
15.89
Avg
22.99
gal
22.99
High
Recorded: 26 minutes ago 11 / 188 frames
To pause the display select Pause.
• To resume playing the recording, reselect Pause.
• To advance the recording frame-by-frame:
• Select “>”.
• Select either “<” or “>”.
• To resume playing the recording, select Pause.
• If replay is desired, click and drag the timeline marker back to the beginning of the timeline and release.
800.MACTOOLS
77
SPECIAL TESTS
Overview
Depending on the vehicle and controller selected, special tests are available.
The special test function is a key component to the tool because it allows circuit testing without ever touching a circuit with a DVOM or other electrical testing equipment. This will also protect electrical circuits from being contaminated or damaged from manual testing with electrical troubleshooting equipment. It is also a quick and easy way to test vehicle controller operation which is dicult to test using traditional methods.
ss02497
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select Special Tests from the home screen.
ss02498
Current
SPECIAL TESTS
2007
Jeep
ALL TESTS
ACCESS VIN
All Special Tests
Search All Special Tests
Access VIN
DIESEL CONTROLS
Read VIN
DPF TESTS
Write VIN
EGR TESTS
Diesel Controls
ENGINE TESTS
Glow Plug
FAN TESTS
DPF Tests
FUEL TESTS
Manual DPF Regeneration
OTHER TESTS
EGR Tests
OXYGEN SENSOR TESTS
EGR Throttle Valve (Service)
RESET TESTS
2. At the special test screen select a special test group from the group selection menu, then select the desired special test within the desired test group.
78
MACTOOLS.COM
ss02499
Current
SPECIAL TESTS
2007
Jeep ALL TESTS
ACCESS VIN
Engine Tests
Compression Test
DIESEL CONTROLS
DPF TESTS
Idle Speed Setpoint
EGR TESTS
ENGINE TESTS
FAN TESTS
FUEL TESTS
OTHER TESTS
OXYGEN SENSOR TESTS
RESET TESTS
3. Only the tests meeting the search criteria are displayed. Select the desired test to be executed.
Note: Some tests may require a registration like Tire Pressure Sensor Test
ss02500
Current
SPECIAL TESTS
2007
Jeep Compression Test
Engine Must Not be Running
For this test
Continue Abort
4. Follow the prompts on the screen.
NOTE: Some of the instruction text may not exactly match what is on the screen. This will be updated as product updates are released.
ss02501
Current
SPECIAL TESTS
2007
Jeep
Compression Test
Fuel to the injectors will be disabled
Battery MUST be fully charged
The average engine speed should be compared with the cylinder selective engine speeds. If a cylinder has a deviation of more than 6 RPM compared with the average engine speed, there is a high probability that the cylinder has a compression problem.
This test should be repeated three times to get a statistical based result.
Continue Abort
5. To terminate a test at any time, use the emergency stop button. To exit special tests normally, select the exit or abort button.
Note: Exit or abort will both stop the current special test and take you back to the start of Special Tests
800.MACTOOLS
79
Note: If there is data streaming attached to the Special Test then you will be taken to Special Tests in Data
Stream.
It is possible to change controllers within the special test menu screen after exiting the current test. All features outside the special test are locked out until the test is terminated to protect the vehicle and the person running the special test. If a function outside the special test is desired, terminate the test and proceed to the desired function. Special tests are not available for all vehicles and controllers. The air bag controller will rarely provide special tests, as actuating the air bag would cause damage to the steering wheel or cabin components. It would also be necessary to replace air bag modules after running the test and clean the interior. Special tests will be continuously updated as more are added; in addition, tests which do not function may be removed during updates as well. There may be tests listed that do not function on the selected vehicle. This is likely due to the fact that many vehicles have different systems depending on sub-model types.
Read DTCs Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to help content related to reading DTCs.
Note: an active internet connection will be required.
View Help
Selecting View Help will open an online operators manual.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
80
MACTOOLS.COM
800.MACTOOLS
81
DIAGNOSTIC INFORMATION
Overview
Diagnostic Information provides diagnostic, repair, and reset information for the selected vehicle.
ss02502
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select Diagnostic Information from the home screen.
ss02503
Current
Diagnostic Information
2007
Jeep
138
Code-Assist Library Direct-Hit®
2
Repair-Trac®
85
Symptom Assist
1 3 5
2 4 R
Symptom List Video Library Drive Cycle Oil Light Reset
PCM Pin TSB Reference Trans Pan ID Location Info
+
_
!
2. Select the desired function from within the Diagnostic Information menu.
AutoDetect Results Number Indication
Diagnostic Information provides diagnostic, repair, and reset information for the selected vehicle.
• Each vehicle and controller will have its own set of indications.
• The indication is displayed on top of the Diagnostic Information selection.
• When entering diagnostic information, the application will conduct a search in the background for the selected vehicle/controller combination to determine the number of items it will contain.
NOTE: If diagnostic information is desired for a different controller or vehicle, return to the Home Screen and change the controller or vehicle there, then re-select Diagnostic Information. Failure to follow this could lead to display errors or communication errors.
NOTE: Not all assets within the Diagnostic Information menu will utilize the AutoDetect Results Number indication feature.
82
MACTOOLS.COM
Code Assist™ Library
This function will allow a search for DTCs by letter/number designation.
ss02504
Current
2007
Jeep
P Codes
(99)
B Codes
(13)
C Codes
(7)
U Codes
(19)
Code-Assist Library
Select DTC Type.
1. Select Code-Assist library from the Diagnostic Information screen.
ss02505
Current
2007
Jeep
P00 Codes
(9)
P01 Codes
(14)
P02 Codes
(7)
P03 Codes
(10)
P04 Codes
(13)
P05 Codes
(7)
P06 Codes
(9)
P07 Codes
(8)
P08 Codes
(1)
Code-Assist Library
Press DTC for Repair Information
P0031
Oxygen Sensor Bank 1 Sensor 1
Heater Circuit Low
P0051
O2 Sensor 2/1 Heater Circuit Low
P0073
Ambient Air Temperature Sensor
Circuit High
P0032
Oxygen Sensor Bank 1 Sensor 1
Heater Circuit High
P0037
Oxygen Sensor Bank 1 Sensor 2
Heater Circuit Low
P0052
O2 Sensor 2/1 Heater Circuit High
P0057
Oxygen Sensor Bank 2 Sensor 2
Heater Circuit Low
P0038
O2 Sensor 1/2 Heater Circuit High
P0058
Oxygen Sensor Bank 2 Sensor 2
Heater Circuit High
2. The next selection divides the information into subcategories B, C, P and U codes. The next selection divides previous groups even more
3. Remaining selections will eventually filter the list down to a shortened DTC list where the user is able to scroll and select the desired DTC
4. Select the DTC to display the DTC information.
5. To return to previous menu screens, select the back arrows at the top of the screen.
800.MACTOOLS
83
Identifix
®
Direct-Hit
®
Identifix® Direct-Hit® requires an account setup with Identifix®. To set up an account, go to www.identifix.
com and complete the necessary steps.
Once an account is set up with Identifix®:
• Select Settings button from the home screen.
• Select Direct-Hit® from the available tabs on the left margin of the screen.
• Input the username and password acquired from
• Identifix® by selecting the empty field.
• Using the virtual keyboard, enter required information for both fields.
• Select Save.
• Information saved will be displayed.
1. Select Identifix® Direct-Hit® from the Diagnostic Information screen.
ss02506
2006 jeep rims - Google...
g
Google file://storage/emulated...
Direct-Hit -- Main Asset...
http://www.identifix.com/asset_search_main.aspx?LogSL=19&LogDL=29&LogWL=2&L
CONTACT REPAIR HOTLINE 3 LATEST UPDATES
HOME
Home
SEARCH FIXES
[Keyword/Code]
Top Searches
For This Vehicle:
1 - P2176
2 - No Start
3 - P1799
4 - P0335
5 - P0318
SERVICE MANUALS
2003 Cadillac CTS 3.2L, V6, VIN N USA
SEARCH ALL
MAINTENANCE QUOTE ESTIMATING HOTLINE MY SHOP
Post Fix Can’t Find OEM Info?
BOOKMARKS
New Vehicle Referral Logout
SPX - SPX Users Viewing Cadillac Vehicles: 733
ESTIMATING
MAINTENANCE QOUTE MOTOR PARTS & LABOR CHILTON LABOR RECALLS
Search
Service Manuals Only
First
Odometer
Choose a Maintenance Schedule:
Last
Dashboard Schedule Which Schedule?
CHANGE ENGINE OIL message
Miles
License
Fleet #
Entry Required
Reset Procedure - Maintenance Indicator
View Traditional maintenance Schedules
Customer Plan
Technician Plan
Identifix® Direct-Hit® is now set up for use on the handset. There are a few areas where Identifix® Direct-Hit® may be selected:
• From DTC information screen after having selected Read DTCs from the Home Screen and a listed DTC
• After running an “All DTC Scan” from the “Read DTCs” screen and after having selected a listed DTC in the All DTC Report screen.
• After running an AST from the Read DTCs screen, and after having selected a DTC under the DTC tab at the AST report screen.
• From the “Diagnostic Information” screen, after having selected Diagnostic Information from the Home
Screen.
84
MACTOOLS.COM
Repair Trac
®
Uses the AutoDetect Results Number Indication feature described above.
1. Select Repair Trac® from the Diagnostic Information screen to view previously reported repairs for the selected vehicle/controller combination.
ss02507
Current
Repair-Trac®
2007
Jeep
Systems
Engine Performance
Starting and Charging
Select the desired system.
• Select the category.
• Select the deficiency.
• Select the symptom.
• Report is displayed describing the problem, how to test and fix, and related DTCs.
Symptom Assist™
This function assists in diagnosing a problem with a vehicle component by selecting apparent symptoms.
1. Select Symptom Assist from the Diagnostic Information screen.
ss02508
Current
Symptom Assist
2003
GMC A/C COMPRESSOR CLUTCH
PROBLEM
A/C PERFORMANCE PROBLEM
A/C Compressor Clutch Problem
Element Name
ABS PUMP RUNS CONTINUOUSLY
Air Conditioning (A/C) Compressor
Action Name
Replaced
ADJUSTABLE PEDAL PROBLEM
Heater Ventilation Air Conditioner
(HVAC) Control Head
Replaced
ANTI-LOCK BRAKES/BRAKE/
TRACTION CONTROL LIGHT/
MESSAGE PROBLEM
ANTI-LOCK BRAKES/TRACTION
CONTROL - FALSE CYCLING/
FAULTY OPERATION
AUTOMATIC TRANSMISSION
COMMUNICATION PROBLEM
AUTOMATIC TRANSMISSION
ENGAGEMENT HARSH/DELAYED
A/C High Pressure Switch
Ambient Air Temperature (AAT)
Sensor
Air Conditioning (A/C) Compressor
Clutch
A/C Low Side Pressure Switch
Replaced
Replaced
Replaced
Replaced
AUTOMATIC TRANSMISSION
NOISE/VIBRATION
Air Conditioner (A/C) Pressure Sensor
Wiring
Repaired
Level Name
Top Reported Fix
Frequently Reported Fixes
Frequently Reported Fixes
Frequently Reported Fixes
Frequently Reported Fixes
Frequently Reported Fixes
Frequently Reported Fixes
2. Select the desired component or component group.
3. Select the desired symptom within the component or component group.
4. To go back to previous screens use the back arrows near the top of the screen.
800.MACTOOLS
85
Symptom List
Diagnostic Information provides diagnostic, repair, and reset information for the selected vehicle.
1. Select Symptom List from the Diagnostic Information screen.
• Displays a list of symptoms associated with the selected vehicle/controller combination.
• Select Symptoms List from the Diagnostic Information menu.
ss02509
Current
Symptoms List
2007
JEEP ENGINE WILL NOT START
Engine Will Not Start
ENGINE LOSS OF POWER
ENGINE MISSES ON
ACCELERATION
ENGINE STALLS OR IDLES ROUGH
Description
Weak battery, corroded or loose battery connections, faulty starter, faulty coil(s) or control unit, incorrect spark plug gap, contamination in fuel system, faulty fuel pump, incorrect engine timing.
ENGINE MISSES AT HIGH SPEED
ENGINE WILL NOT START
ENGINE LOSS OF POWER
ENGINE MISSES ON
ACCELERATION
ENGINE STALLS OR IDLES ROUGH
ENGINE MISSES AT HIGH SPEED
2. Select the symptom that is currently being exhibited by the vehicle on the vehicle.
Video Library
When Video Library is selected the user will be taken to YouTube videos. These videos will illustrate how to perform various functions on the handset.
1. Select Video Library from the Diagnostic Information screen.
ss02510
Video Search releasenotes.service-sol...
Please enter search term(s)...
Tool Operation-Auto Detect DTC
Tool Operation-Auto ID
Tool Operation-Automated System Test
2. Search YouTube website for videos.
86
MACTOOLS.COM
Drive Cycle
The OBDII system has a series of systems that run self-tests. These systems or components have to be made ready either by simply turning on the ignition or by manipulating the system in some manner. This is called
Drive Cycle. Drive cycle information is listed for continuous and non-continuous monitors.
1. Select Drvice Cycle from the Diagnostic Information screen.
ss02511
Current
2003
GMC
1 3 5
2 4 R
Drive Cycle
A/C SYSTEM REFRIGERANT
MONITOR
CATALYST MONITOR
COMPREHENSIVE COMPONENT
MONITOR
EGR SYSTEM MONITOR
EVAP SYSTEM MONITOR
FUEL SYSTEM MONITOR
FULL DRIVE CYCLE
MISFIRE MONITOR
O2 SENSOR HEATER MONITOR
O2 SENSOR MONITOR
1) Cold start engine coolant temperature < 50 degrees Celsius, with air conditioning & rear defrost on, idle 2.5 minutes in drive. Before procedding turn accessories off.
2) Acceleration to 55 miles per hour, 1/2 throttle, air conditioning off.
3) 3 minutes steady state cruise 55 & 60 miles per hour.
4) Deceleration to 20 miles per hour (clutch out) no brake.
5) Acceleration at 3/4 throttle to 55-60 miles per hour, then steady state cruise for 5 minutes.
6) Deceleration no brake, end of cycle.
2. Scroll through the list until the desired monitor or drive cycle is found.
3. Select the desired drive cycle and follow the instructions.
Oil Light Reset
On newer vehicles, the oil light reset procedure will indicate how the oil life information can be reset after an oil change.
1. Select Oil Light Reset from the Diagnostic Information screen.
ss02512
Current
Oil Light Reset
2003
GMC
Oil Light Reset Procedures
1) Turn the ignition key to the RUN position.
2) Fully push and release the accelerator pedal 3 times within 5 seconds.
3) If the CHANGE OIL SOON light flashes, the system is resetting.
4) Turn the key to OFF.
5) Start the vehicle.
6) The oil life will change to 100%
7) If the Change Oil Soon light comes back on, the system has not reset. Repeat the procedure.
2. Select Oil Light Reset from the Diagnostic Information menu screen.
800.MACTOOLS
87
PCM Connector Pin Information
Displays a list of which connector and pin a component or sensor is received through on the PCM.
1. Select PCM Pin Information from the Diagnostic Information screen.
ss02513
Current
PCM Pin
2003
GMC PCM Pin
C1-4
C1-7
C1-8
Pin Number
C1-1
C1-2
C1-3
C1-11
C1-12
Description
Ground
12 Volt Reference
Fuel injector 3 Control
Fuel injector 2 Control
5 Volt Reference
5 Volt Reference
Knock Sensor 2 Signal
Crankshaft Position Sensor 1 Signal
2. Scroll through the list and select the desired sensor or component is listed.
ss02514
Current
PCM Pin
2003
GMC PCM Pin
Connector:
C1
Connector Color:Blue
Pin Number:
Wire Color:
Description:
KOER
1
Black/White
Ground
N/A N/A
88
MACTOOLS.COM
Technical Service Bulletin (TSB) References
Displays TSBs associated with the vehicle/controller combination.
1. Select TSB Reference from the Diagnostic Information screen.
ss02515
Current
2003
GMC
TSB Number
02-09-41-001
TSB Reference
01-07-30-002C
01-07-30-036C
01-07-30-038B
02-06-05-004A
02-07-30-001C
03-04-21-001D
03-06-04-030
TSB Description
Computers & Controls - DTC’s Set When Replacing Modules
Electrical - Malfunction Indicator Lamp ON / Automatic Transmission Stuck in
3rd Gear
Automatic Transmission - Diagnostic Trouble Code P0756 Diagnostic Tips
Automatic Transmission - 4L60-E / 4L65-E Malfunction Indicator Lamp ON /
Diagnostic Trouble Code P0757 / Slipping
Emissions - Catalytic Converter Damage / Misfire Codes Set
Automatic Transmission - 4L60E and 4L65E Diagnostic Trouble Code P0894 /
P1870 Diagnostics
Drivetrain - 4x4 Inoperative / Lamp Flashing / Diagnostic Trouble Code’s Set
Fuel System - Possible Malfunction Indicator lamp ON / Driveability Symptoms
2. Scroll through the list until the desired TSB is found
Trans Pan ID
Displays a list of gasket images that correspond to specific transmissions.
1. Select Trans Pan ID from the Diagnostic Information screen.
ss02516
Current
Trans Pan ID
2003
GMC
TRANSMISSION PAN CHART IMAGE
125/125C
180/3L30
2. Scroll through the list of gasket images until the matching gasket is found. Corresponding information is listed below each image.
800.MACTOOLS
89
Location
Used to find where specific components are located.
1. Select Location Info from the Diagnostic Information screen.
ss02517
Current
Location
2004
Ford
FUSE BOX LOCATION
ECU LOCATION
DLC LOCATION
COMPONENT LOCATION
Battery junction box is located in the left rear engine compartment. The central junction box is located under the dash panel, near the steering column.
2. Scroll through the list and select the desired component.
Brake Bleed Procedure (ABS)
Provides the procedure on how to bleed the brakes after replacing brake calipers or opening a brake line to atmosphere.
1. Select Brake Bleed Procedure from the Diagnostic Information screen.
ss02518
Current
Brake Bleed Procedure
2004
Ford
ABS Bleed Procedures
Brake Bleed Sequence: N/A
GRAVITY BLEED
1) Warning: brake fluid contains polyglycol ethers and polyglycols. Avoid contact with eyes. Wash hands throughly after handling. If brake fluid contact eyes, flush eyes with running water for 15 minutes.
2) Get medical attention if irritation persists. If taken internally, drink water and induce vomiting. Get medical attention immediately. failure to follow these instructions may result in personal injury.
3) CAUTION: Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
4) CAUTION: Do not spill brake fluid onto painted or plastic surfaces. If spilled, wipe away immediately before damage to the plastic or painted surfaces occurs.
5) NOTE: When any part of the hydraulic system has been disconnected for repair or new installation, air may get into the system and cause spongy brake pedal action.
2. It may be necessary to change controllers at the Home Screen, then re-enter diagnostic information for this selection to become available (ABS, ABS/VSES).
NOTE: The sequence may be contained within the previous brake bleed procedure section if it is not separately listed on the Diagnostic Information screen.
90
MACTOOLS.COM
Tune Up Specifications
Provides specifications for specific components when a tune up is performed.
1. Select Tune Up Specs from the Diagnostic Information screen.
ss02519
Current
2004
Ford
Injector
Starter
Regulator
Timing
Spark Plug
Firing Order
Battery
Tune Up Specs
Specification: 11 to 18 Ohms
2. Some of the tune up specifications contained in this section include the following:
• Starter
• Generator
• Regulator
• Spark plug
• Idle speed
• Fuel pressure
• Compression
• Firing order
Key Programming
Displays instructions for the selected vehicle for programming a key.
1. Select Key Programming from the Diagnostic Information screen.
ss02520
Current
2004
Ford
1
3
2
Key Programming
Battery Location
Battery Replacement
Immobilizer
2 fig107944
1
3
4
Remote Alarm/Central Locking
System Operation
Pressing the LOCK button once locks all doors and activates the alarm system (if fitted).
Pressing the LOCK button twice within 3 seconds confirms all doors locked by sounding the horn once.
The horn will sound twice if a door is open
Pressing the UNLOCK button once deactivates the alarm system (if fitted) and unlocks the driver’s door only.
Pressing the UNLOCK button twice within 3 seconds deactivates the alarm system (if fited) and unlocks all doors.
Pressing the panic button once activates the panic alarm. The horn will sound and the parking lamps will flash
Pressing the panic button agiain, of turning ignition ON deactivates the panic alarm.
Programming
When
Remote transmitter added or replaced.
System Malfunction.
How
Obtain all remote transmitters.
Switch ignition from OFF to ON 8 times within 10 seconds:
Doors should lock then unlock.
Within 20 seconds:
Press any button on the first remote transmitter.
Doors should lock then unlock.
2. Follow the prompts on the screen to program a key and or replace battery in key.
800.MACTOOLS
91
Battery Disconnect
Displays procedures for disconnect the battery on the selected vehicle.
1. Select Battery Disconnect from the Diagnostic Information screen.
ss02521
Current
2004
Ford
+
_
!
Battery Disconnecta
Battery Location
Battery Location
See Image
General Information
Before Battery
Disconnection
Before Battery
Connection
122448
2. Follow the prompts on the screen to disconnect and reconnect the battery.
3. Follow procedures for updating vehicle systems after battery has been disconnected.
TMPS Quick Info
Describes the operating procedures for the Tire Pressure Monitor System (TPMS) for the selected vehicle.
1. Select TMPS Quick Info from the Diagnostic Information screen.
ss02522
Current
TPMS Quick Information
2009
Honda
DESCRIPTION
Description
RESET PROCEDURES...
RESET TRIGGER
TORQUE SPECS
TPMS SENSOR PART
NUMBER
System Description: When the vehicle speed exceeds 28 mph (45 km/h), the Tire Pressure
Monitor System (TPMS) Control Unit monitors the pressure in all four tires and the system itself. System Operation: The TPMS has two LED indicators that are part of the gauge module; a low-pressure indicator and a system indicator. When the TPMS Control Unit detects low pressure in a tire (or a problem in the system) it turns on the appropriate indicator(s). If low tirw pressure is detected, the low pressure indicator comes on. If a problem in the system is detected, the TPMS indicator comes on. If low tire pressure and a problem in the system are detected, only the TPMS indicator comes on. With the system functioning properly, the low pressure indicator should come on when the ignition is turned
ON. It should then go off 2 seconds later. If this is not the case, there is a problem with the system. If the system detects low pressure in any tire, the low-pressure indicator will come on and the TPMS control unit will set one of the following codes: DTC 11, DTC 13, DTC 15 and DTC 17. When the tire pressure returns to normal, the control unit will turn off the indicator but store the DTC. If the control unit detects a problem with the system while a low-pressure problem exists, it will turn off the tire pressure indicator, store the DTC(s) and turn on the TPMS indicator. If a flat tire is replaced with the spare tire, the TPMS indicator will come on and set a DTC (32, 34, 36 or 38 depending on the tire) because the system is no longer receiving a signal from that tire’s transmitter. There are no electronics in the spare tire so this is not an indication of a problem with the spare. Component Description: The
TPMS uses the following components: Control Unit, Indicators and Tire Pressure Sensors.
These components work together to monitor and rport tire pressure whenever the vehicle
2. Follow the prompts on the screen to reset the tire pressure monitors.
92
MACTOOLS.COM
Read DTCs Button Definitions
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to help content related to reading DTCs.
Note: an active internet connection will be required.
View Help
Selecting View Help will open an online operators manual.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
800.MACTOOLS
93
MAINTENANCE TESTS
Overview
Maintenance Tests provide a way for specific systems to be recalibrated or reset after service. Maintenance test availability will vary from vehicle to vehicle, and will be updated over time.
Maintenance tests are the same as special tests, but this is a shortcut to most frequently used tests on the selected vehicle. These specific tests can also be found under special tests.
Maintenance tests can be selected at the time of controller selection for the current vehicle being worked on.
ss02525
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select Maintenance Test from the Home Screen.
ss02526
YEAR MAKE MODEL SUBMODEL ENGINE CONTROLLER
MAINTENANCE
TESTS
ENGINE GLOBAL OBDII
TRANSMISSION
ABS
WIRELESS CTRL
MODULE (TPMS)
OCCUPANT
CLASSIFICATION
CABIN COMP NODE RADIO
OCCUPANT
RESTRAINT
CONTROL
STEERING ANGLE
AUTO SWAY BAR
TIPM CENTRAL
GATEWAY
AUDIO
Selected
2007 Jeep
Wrangler Unlimited Rubicon 3.8
Cancel
2. Select the controller.
Note: If no maintenance tests are found for selected vehicle select a different controller.
94
MACTOOLS.COM
ss02527
YEAR MAKE
MAINTENANCE
TESTS
MODEL SUBMODEL ENGINE CONTROLLER
ENGINE GLOBAL OBDII TRANSMISSION
WIRELESS CTRL
MODULE (TPMS)
CABIN COMP NODE
CLASSIFICATION
Battery/Charging
ELECTRONIC
SUSPENSION
Brake Service
CLIMATE
TPMS Registration
ELECTRIC
OVERHEAD
MODULE
Cancel
AUTO SWAY BAR
FCM CENTRAL
GATEWAY
ABS
AUDIO
Selected
2007 Jeep
Wrangler Unlimited Rubicon 3.8
3. Select the desired category for the component or system being worked on.
Note: If there are no sub-sections available for the selected category go to step 5.
ss02528
YEAR MAKE MODEL SUBMODEL ENGINE CONTROLLER
MAINTENANCE
TESTS
PCM GLOBAL OBDII ABS VSES
Cancel
TRACTION ASSIST
CHIME
AIRBAG
ELECTRONIC
SUSPENSION
Select a Maintenance Test
Oil Life Reset
CLIMATE
ELECTRIC
OVERHEAD
BASE RADIO
FCM CENTRAL
GATEWAY
BODY CONTROL
MODULE
INSTRUMENT
PANEL CLUSTER
NAVIGATION
RADIO
ONSTAR
PASSENGER DOOR
MODULE
REAR AUX
CLIMATE CONTROL
REAR HVAC
Selected
2003 GMC
Yukon XL 2500 SLT 8.1
4. Select the desired test to be performed.
ss02529
YEAR MAKE MODEL SUBMODEL
MAINTENANCE
TESTS
PCM
ENGINE CONTROLLER
GLOBAL OBDII ABS VSES
Cancel
TRACTION ASSIST
CHIME
NAVIGATION
RADIO
AIRBAG
CLIMATE
VSES
Maintenance Test.
ELECTRONIC
SUSPENSION
ELECTRIC
OVERHEAD
MODULE
BASE RADIO
The controller for the selsected Maintenance Test Catagory is
ABS
Please select that controller to continue the Vehicle Selection process and proceed to SPECIAL TESTS to run the desired
FCM CENTRAL
GATEWAY
OK
ONSTAR
PASSENGER DOOR
MODULE
REAR AUX
CLIMATE CONTROL
BODY CONTROL
MODULE
INSTRUMENT
PANEL CLUSTER
REAR HVAC
Selected
2003 GMC
Yukon XL 2500 SLT 8.1
5. Follow prompts on the screen.
Cancel
800.MACTOOLS
95
ss02497
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
2:59
6. Select Special Tests from the Home Screen.
ss02530
Current
SPECIAL TESTS
2009
Jeep
ALL TESTS
ACCESS VIN
All Special Tests
Search All Special Tests
Access VIN
DIESEL CONTROLS
Read VIN
DPF TESTS
Write VIN
EGR TESTS
Diesel Controls
ENGINE TESTS
Glow Plug
FAN TESTS
DPF Tests
FUEL TESTS
Manual DPF Regeneration
OTHER TESTS
EGR Tests
OXYGEN SENSOR TESTS
EGR Throttle Valve (Service)
RESET TESTS
7. At the special test screen select a special test group from the group selection menu, then select the desired special test within the desired test group.
Note: For more information refer to Special Tests section.
96
MACTOOLS.COM
800.MACTOOLS
97
ALL SYSTEM DTC SCAN
Overview
The All System DTC Scan will scan all available controllers on the selected vehicle.
Depending on the vehicle, the handset may ask qualifying questions concerning particular controller types for the vehicle being scanned. If unsure what selection to pick find the manufacturer’s Regular Production Option
(RPO) Code list sticker on the vehicle, then find the corresponding code for the desired controller. Typical locations for the RPO are the trunk, glove box, or doorjamb area.
These questions may be skipped by selecting Skip Controller. Scan progress will be indicated by the progress bar near the bottom of the screen.
ss02531
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select All System DTC Scan from the Home Screen.
ss02532
Current
All System DTC Scan
2004
Volkswagon Building controller list.. Please Wait..
Finding ABS (03) controllers
Skip controller
ABS Bosch 5.7
2. Select all controller qualifiers
Note: Not all vehicles will have qualifiers
Select Controller Qualifer
98
MACTOOLS.COM
ss02533
Current
All System DTC Scan
2004
Volkswagon
Raeding DTC’s from INSTRUMENTS (17)
18%
AUTO TRANSMISSION (02)
ENGINE (01)
AIRBAG (15)
INSTRUMENTS (17)
ABS (03)
SUSPENSION ELECTRONICS (14)
STEERING WHEEL (16)
ALL WHEEL DRIVE (22)
3. Scan progress will be indicated by the progress bar in the middle of the screen.
Note: If any of the conrollers have DTC’s go to step 6.
ss02534
3 DTC(s) found
5 DTC(s) found
3 DTC(s) found
Reading DTCs
Current
All System DTC Scan
2007
Jeep Report ready for viewing.
100%
AUTO SWAY BAR
AUDIO
RADIO
STEERING ANGLE
TIPM CENTRAL GATEWAY
No Diagnostic Trouble Codes
No Diagnostic Trouble Codes
No Diagnostic Trouble Codes
No Diagnostic Trouble Codes
No Diagnostic Trouble Codes
4. Wait for scan to finish.
Note: There is no arrow beside controller without a DTC and clicking on that line does nothing.
ss02535
Current
2004
Volkswagon
All System DTC Scan
Report
Primary Controller ENGINE
No Diagnostic Trouble Codes
Secondary Controller TRANSMISSION
Error Communication Error. Please verify that cables are...
Secondary Controller ABS
No Diagnostic Trouble Codes
Secondary Controller CABIN COMP NODE (TPMS)
No Diagnostic Trouble Codes
Secondary Controller WIRELESS CTRL MODULE (TPMS)
Read Codes
Read Codes
Read Codes
Read Codes
5. The controller without a DTC has no DTC line that is selectable and clicking on the line has no effect.
800.MACTOOLS
99
ss02536
Current
All System DTC Scan
2004
Volkswagon Report ready for viewing.
100%
CENTRAL CONVENIENCE (46)
SOUND SYSTEM (47)
XENON RANGE (55)
RADIO (56)
TV TUNER (57)
AUX FUEL TANK (58)
3 DTC(s) found
3 DTC(s) found
3 DTC(s) found
3 DTC(s) found
3 DTC(s) found
3 DTC(s) found
PARK ASSIST (76) 3 DTC(s) found
TELEPHONE (77)
3 DTC(s) found
6. Wait for scan to finish.
Note: There is no arrow beside controller without a DTC and clicking on that line does nothing
ss02537
Current
2004
Volkswagon
All System DTC Scan
Report
Primary Controller AUTO TRANSMISSION (02)
00258 Solenoid Valve 1
00260 Solenoid Valve 2
00266 Solenoid Valve 5
Secondary Controller ENGINE (01)
18080 Coolant Fan Control 1v Open Or Short To Ground
18359 Radiator Fan 2 Movement Restricted/Jammed
16394 Camshaft Position A Actuator Circuit (Bank 1)
Read Codes
Read Codes
Read Codes
Read Codes
Read Codes
Read Codes
Read Codes
16396 Camshaft Position A - Timing Over-Retarded (Bank 1)
Secondary Controller AIRBAG (15)
00003 Control Module
Read Codes
Read Codes
7. DTCs will be read from all available vehicle controllers.
• Select a listed DTC for Related Diagnostic Information See Diagnostic Information section
• If a DTC has Code Criteria available there will be an “*” next to the DTC.
Once completed the handset will display a list of all the DTCs found on the vehicle and group them by controller. If the handset was unable to communicate with a controller, it will be indicated under the specific controller. Communication problems on certain controllers may be attributed to the vehicle not having that controller.
Controllers are sometimes listed for a particular vehicle that do not actually exist.
100
MACTOOLS.COM
800.MACTOOLS
Read DTCs Button Definitions
Refresh DTCs Button
Tapping the Refresh button initiates a fresh scan of DTCs from the vehicle.
Share DTCs Button
Tapping the Share button opens the app and initiates one of two options, share by email or
Bluetooth email concontaining a list of all the
DTCs set.
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to help content related to reading DTCs.
Note: an active internet connection will be required.
View Help
Selecting View Help will open an online operators manual.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
101
BROWSER
Overview
An internet browser window is available for direct internet access.
ss02538
2:59
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
1. Select Browser from the Home Screen.
The Handset will launch the internet browser. Links to common technical and repair websites are provided.
Select the keyboard icon to input text.
Note: The handset will need to have a Wi-Fi connection.
CONNECTING TO WI-FI NETWORKS
See Android Settings for more information on setting up and connecting to a wireless network.
ss02539 releasenotes.service-sol...
Webpage not availvable 81-316-0742CD - 2007- ...
file:///data/info/fasttouch/FastTouch.htm
FastTouch Tech Commun...
You
Fast Touch Websites
TECH COMMUNITIES
REPAIR INFORMATION
OEM
TECH4TECH
iATN
TST
1. Select Tech Communites brings up appropriate tech community web page.
102
MACTOOLS.COM
ss02540
Video Search
You
Fast Touch Websites
TECH COMMUNITIES
REPAIR INFORMATION
OEM
FastTouch Repair Inform..
IDENTIFI
FIND AND FIX FASTER
autodata
MOTO
LOGIC
2. Select Repair Information brings up appropriate repair information web page.
ss02541
Video Search
You
Fast Touch Websites
TECH COMMUNITIES
REPAIR INFORMATION
OEM
FastTouch OEM
3. Select OEM brings up the manufactures technical web page.
800.MACTOOLS
103
AUTOMATED SYSTEM TEST
Overview
The Automated System Test (AST) will scan all available controllers on the selected vehicle for Modes 1-7.
Depending on the vehicle, the handset may ask qualifying questions concerning particular controller types for the vehicle being scanned. If unsure what selection to pick, find the manufacturer’s Regular Production Option
(RPO) code list sticker on the vehicle, and then find the corresponding code for the desired controller. Typical locations for RPO are trunk, glove box, or doorjamb. These questions may be skipped by selecting Skip Controller.
ss02542
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan
Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select Automated System Test from the Home Screen.
ss02543
Current
Automated System Test
2007
Jeep
Building controller list.. Please Wait..
Finding AUTO SWAY BAR controllers
2. Wait for the list to be completed
104
MACTOOLS.COM
ss02544
Current
2007
Jeep
Automated System Test
Reading DTCs form CABIN COMP NODE
19%
ENGINE
TRANSMISSION
WIRELESS CTRL MODULE (TPMS)
TIPM CENTRAL GATEWAY
STEERING ANGLE
CABIN COMP NODE
RADIO
OCCUPANT RESTRAINT CONTROL
3. Scan progress will be indicated by the progress percentage bar on the screen.
ss02545
9 DTC(s) found
9 DTC(s) found
9 DTC(s) found
9 DTC(s) found
9 DTC(s) found
Reading DTC’s
Current
2007
Jeep
SUMMARY
Automated System Test
Report ready for viewing.
100%
Check supported OBDII modes
OBDII DS Snapshot (Mode 1)
Readiness Monitor Tests (Mode 1)
Freeze Frame Data (Mode 2)
12 DTC(s) found
11 DTC(s) found
1 DTC(s) found
Oxygen Sensor Tests (Mode 5)
Non Continuously Monitored Tests (Mode 6)
VIN (Mode 9)
80 DTC(s) found
12 DTC(s) found
1 DTC(s) found
Calibration Identification IDs (Mode 9)
4. Scan progress will be indicated by the progress percentage bar on the screen.
• Select Green Arrow to review summary report (step 6) ss02546
1 DTC(s) found
Current
Automated System Test
2007
Jeep
Report ready for viewing.
100%
OBDII DS Snapshot (Mode 1)
Calibration Identification IDs (Mode 9) Results
Read
BOSCHA1037366956
Freez
Close
Oxygen Sensor Tests (Mode 6)
Non Continuously Monitored Tests (Mode 6)
VIN (Mode 9)
Calibration Identification IDs (Mode 9)
Calibration Verification IDs (Mode 9)
5. If available select arrow at end of line to view information on item.
NOTE: Available items will vary from vehicle to vehicle.
12 DTC(s) found
1 DTC(s) found
1 DTC(s) found
30 DTC(s) found
12 DTC(s) found
1 DTC(s) found
1 DTC(s) found
1 DTC(s) found
800.MACTOOLS
105
Summary Report
ss02547
Current
2007
Jeep
SUMMARY
DTCs
Automated System Test
Report
DATA STREAM SNAPSHOT
Summary
VIN: 1G6DM57N530102274 CONTROLLER: ENGINE
CALIBRATION ID(S):BOSCHA1037366956, 4EF7033C
MODE 1
FREEZE FRAME
MODE 5
MODE 6
DTCs Found
108
Oxygen Sensor Tests (Mode 5)
Data Items
12
Non Continuously Monitored Tests (Mode 6)
Freeze Frame Data (Mode 2)
11
80 3
Passed
Readiness Monitor Tests (Mode 1)
6
Ready
0
Not Ready
5
9
Failed
Not Supported
AST summary reports items found on the vehicle, such as:
• Controllers found on vehicle
• DTCs
• Data Stream Snap Shot
• Mode 1 (Readiness Monitor)
• Freeze frame
• Mode 5 (O2 sensor)
• Mode 6 (Non-continuous monitor tests)
NOTE: Available selections will vary from vehicle to vehicle.
DTCs
ss02548
Current
2007
Jeep
SUMMARY
DTCs
Automated System Test
Report
Diagnostic Trouble Codes
DATA STREAM SNAPSHOT
MODE 1
FREEZE FRAME
MODE 5
MODE 6
Primary Controller ENGINE
B1000 Air Conditioning Switch Request Input Circuit/
Performance
B1001 Air/Conditioning Switch Request Input Circuit Low
B1002 Air/Conditioning Switch Request Input Circuit High
B1000 Air Conditioning Switch Request Input Circuit/
Performance
B1001 Air/Conditioning Switch Request Input Circuit Low
B1002 Air/Conditioning Switch Request Input Circuit High
B1000 Air Conditioning Switch Request Input Circuit/
Performance
B1001 Air/Conditioning Switch Request Input Circuit Low
Active
Active
Active
Pending
Pending
Pending
Stored
Stored
DTCs recorded are displayed. When selecting DTCs, diagnostic information is also available (same information as the Read DTCs screen).
106
MACTOOLS.COM
Data Stream Snapshot
ss02549
Current
2007
Jeep
SUMMARY
Automated System Test
Report
Data Stream Snapshot
DTCs
Global OBDII
DATA STREAM SNAPSHOT
MODE 1
Engine Coolant Temperature Distance Since DTC Clear
FREEZE FRAME
MODE 5
90
°F
31042 miles
MODE 6
Distance MIL Active
19502 miles
Fuel Rail Pressure Gauge
70.1 psi
Fuel Rail Pressure Relative To Manifold
Vacuum
Evaporative Emissions System Vapor
Pressure
144.3 psi
-236.54 iHg
Catalyst Temperature Bank 1 Sensor 1 Catalyst Temperature Bank 2 Sensor 1 Catalyst Temperature Bank 1 Sensor 2
Data stream Snapshot, is a current view of the onboard vehicle sensors.
Mode 1 (Readiness Monitor)
ss02550
Current
2007
Jeep
SUMMARY
DTCs
Automated System Test
Report
Readiness (Mode 1)
DATA STREAM SNAPSHOT
MODE 1
FREEZE FRAME
MODE 5
MODE 6
Monitor Description
Catalyst Monitor
Misfire Monitor
2nd Air Monitor
Evaporative Emissions Monitor
Comprehensive Component Monitor
Fuel System Monitor
Heated Catalyst Monitor
A/C System Refrigerant Monitor
Status
Ready
Ready
Ready
Not Supported
Ready
Ready
Not Supported
Ready
Oxygen Sensor Monitor Not Supported
Readiness Monitor Tests displays the results from the continuous monitors available on the selected vehicle.
There are three states: ready, not ready, and not supported. If the monitor is not ready, a drive cycle must be completed prior to running this test. For more information regarding drive cycles, refer to diagnostic functions
Mode 1 readiness.
800.MACTOOLS
107
Freeze Frame
ss02551
Current
2007
Jeep
SUMMARY
Automated System Test
Report
Mode 2 Freeze Frames
DTCs
Freeze Frame 0 - P0123
DATA STREAM SNAPSHOT
MODE 1
FREEZE FRAME
MODE 5
MODE 6
1. Select a frame.
ss02552
Current
2007
Jeep
SUMMARY
Automated System Test
Report
Mode 2 Freeze Frames
DTCs
DATA STREAM SNAPSHOT
MODE 1
Engine Coolant
Temperature
241
°F
Barometric Pressure
48 inHg
FREEZE FRAME
MODE 5
MODE 6
Distance MIL Active
39374 miles
Fuel Rail Pressure
Relative To Manifold
Vacuum
500.4 psi
Distance Since DTC Clear Fuel Rail Pressure Gauge
6877 miles
100.4 psi
Evaporative Emissions
System Vapor Pressure
-1389.98 iHg
Catalyst Temperature
Bank 1 Sensor 1
5466
°F
Catalyst Temperature
Bank 2 Sensor 1
Catalyst Temperature
Bank 1 Sensor 2
Catalyst Temperature
Bank 2 Sensor 2
1234
°F
3240
°F
2197
°F
Mode 2 displays recorded data in the form of a DS snapshot by the vehicle’s computer when specific DTC are set and the MIL is illuminated.
108
MACTOOLS.COM
Mode 5 (Oxygen sensor tests)
Mode 5 views O2 sensor monitor test results.
ss02553
Current
2007
Jeep
SUMMARY
Automated System Test
Report
Oxygen Sensor Tests (Mode 5)
DTCs
DATA STREAM SNAPSHOT
MODE 1
FREEZE FRAME
MODE 5
MODE 6
Description
Bank 1 Sensor 1
High Sensor Voltage For Switch Time Calculation
Lean To Rich Sensor Switch Time
Lean To Rich Sensor Threshold Voltage
Low Sensor Voltage For Switch Time Calculation
Maximum Sensor Voltage For Test Cycle
Minimum Sensor Voltage For Test Cycle
Rich To Lean Sensor Switch Time
Min
0.000
0.000
0.000
0.000
0.000
0.000
0.000
Value
0.003
0.003
0.003
0.002
0.003
0.002
0.003
Max
1.275
1.275
1.275
1.020
1.275
1.020
1.275
Units
V sec
V
V
V sec
V
Rich To Lean Sensor Threshold Voltage 0.000
0.003
1.275
V
Mode 5 views O2 sensor monitor test results. Mode 5 displays the average of the O2 sensor monitor test results measured over a period of time. The parameters of this measurement vary between manufacturers. It may be necessary to run the vehicle for a period of time to allow the O2 sensors to fully warm up and begin operating.
Note: Mode 5 is not supported on all vehicles.
Mode 6 (Non-continuous monitor tests)
Mode 6 views onboard monitoring test results for noncontinuous monitor systems.
ss02554
Current
Automated System Test
Report
2007
Jeep
SUMMARY
DTCs
Non-Continuously Monitored Tests
(Mode 6)
DATA STREAM SNAPSHOT
MODE 1
FREEZE FRAME
MODE 5
MODE 6
ECU: ENGINE
TID 1
CID 1
TID 1
TID 1
TID 2
CID 2
N/A
MIN
TID 2
TID 2
TID 3
CID 3
N/A
MIN
TID 3
TID 3
TID 4
N/A
MIN
TID 4
14080
VALUE
42117
VALUE
27283
MAX
18690
MAX
Passed
N/A
UNITS
Failed
N/A
UNITS
Failed
8589
VALUE
1622
MAX
N/A
UNITS
Failed
Non-Continuous Monitor Tests (Mode 6) are pass/fail tests, including certain EVAP tests, catalyst, and EGR.
The following information is reported:
• ECU.
• TID (test identification) indicates the system monitor.
• CID (component identification) indicates the component tested and its test value.
• Minimum value, maximum value, and current value for each non-continuous monitor.
• Pass or fail test result.
Each vehicle manufacturer assigns a code number to their system monitors and components. Refer to the vehicle manufacturers Mode 6 code chart to determine the failure indicated by the TID and CID. If this chart is not readily available, run an automated system test (AST) from the DTC screen and select Mode 6. See Read
DTCs section for more information regarding steps to complete this action. This may provide a more detailed description of the Mode 6 test information.
800.MACTOOLS
109
Automated System Test (AST) Button Definitions
Refresh DTCs Button
Tapping the Refresh button initiates a fresh scan of DTCs from the vehicle.
Share DTCs Button
Tapping the Share button opens the app and initiates one of two options, share by email or
Bluetooth email containing a list of all the DTCs set.
Menu Button
Tapping the Menu button displays a pop-up link that takes the user to help content related to reading DTCs.
Note: an active internet connection will be required.
View Help
Selecting View Help will open an online operators manual.
Take Screen Capture
Selecting Take Screen Capture will save a copy of the current open screen.
110
MACTOOLS.COM
VIEW SAVED TESTS
Overview
The View Saved Tests functions allows the capability to recall previously run tests.
ss02555
2:59
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
1. Select Veiw Saved Tests from the Home Screen.
ss02556
File picker storage emulated
1/01/1970 12:00 am extsd
1/01/1970 12:00 am sdcard0
1/03/2016 7:43 pm udisk
File name
1 q w
2 a s z e
3 d x r
4 f c
?123
,
2. Navigate down to the desired saved test.
Note: Might require selecting multiple directories.
t
5 g v y
6 h b u
7 n j i
8 k m o
9 l
!
p
0
.
?
Pick file
800.MACTOOLS
111
ss02557
File picker storage emulated data dtcReport-20160314124713.html
14/03/2016 12:47 pm com.bosch.mrst_launcher.control.fragment
dtcReport-20160314124722.html
14/03/2016 12:47 pm dtcReport-20160314124806.html
14/03/2016 12:48 pm files reports
2.94KB
2.94KB
2.94KB
File name
3. Select Specfic file and hit Pick File.
ss02558
Marvel’s Captain America...
Webpage not available 192.19.253.11:8081/ma...
ESI[tronic] Web dtcReport-20160314124...
file:///storage/emulated/0/data/com.bosch.mrst_launcher.control.fragment/files/reports/dtcReport-20160314124713.h1
DTC Report
Vehicle Information
2007 Jeep Wrangler Unlimited Rubicon 3.8 ENGINE
B1000
Air Conditioning Switch Request
Input Circuit/Performance
B1001
Air/Conditioning Switch Request
Input Circuit/Low
B1002
Air Conditioning Switch Request
Input Circuit/High
Pick file
Active
B1000
Air Conditioning Switch Request
Input Circuit/Performance
Active
B1001
Air/Conditioning Switch Request
Input Circuit/Low
Active
B1002
Air Conditioning Switch Request
Input Circuit/High
4. View results from save test.
112
MACTOOLS.COM
800.MACTOOLS
113
VIEW DATA STREAM RECORDINGS
Overview
The View Data Stream Recordings allows the capability to review previously recorded data.
ss02559
2:59
Active
Search Google for ...
1001
101001
0101
CHECK
Diagnostic
Information Read DTCs Data Stream Special Tests
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Maintenance Tests
All System DTC
Scan
Browser Settings
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
System Wiring
Diagrams
OBD-II
Select Vehicle
Tue, 10 May 2016
1. Select View Data Stream Recordings from the Home Screen.
ss02560
Active
Jeep
2007
Jeep
Wangler
Unlimited
Engine
Search Google for ...
CHECK
1001
101001
0101
CHECK
Read DTCs Data Stream
RECORDINGS
28 minutes ago
ENGINE
All System DTC
Scan
ENGINE
2003 Cadillac CTS Luxury Sport
Automated System
Test Veiw Saved Tests
Special Tests
188 frames
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
2. Select recording.
Note: To delete recording, swipe left and click Delete.
Diagnostic
Information
Settings
System Wiring
Diagrams
2:59
114
MACTOOLS.COM
3. View recording ss02561
Current
1001
101001
0101
Recorded Data Stream
2003 Cadillac CTS Luxury Sport ENGINE
Vehicle Speed Engine Coolant
Temperature
88
32
Intake Air Temperature Fuel Tank Pressure
205
36
126
-36
3.6
-4.3
Mileage Since DTC
Cleared
40622 miles
7855
Low
41578
Avg
Calculated Converter
Temperature
79187
High
1011
-54
A
Z
Mileage Since MIL
Request
2
30762
Low
Fuel Level
36191
Avg
35592 miles
39732
High
10.59
Low
15.89
Avg
22.99
gal
22.99
High
Recorded: 26 minutes ago 11 / 188 frames
800.MACTOOLS
115
SYSTEM WIRING DIAGRAMS
Overview
System Wiring Diagrams provides OEM specific, Full color, Full system diagrams.
SS02594
Active
Search Google for ...
CHECK
Read DTCs
1001
101001
0101
Data Stream Special Tests
NISSAN
2015
NISSAN
TITAN
5.6L
ENGINE
Maintenance Tests
All System DTC
Scan Browser
CHECK
Automated System
Test Veiw Saved Tests
View Data Stream
Recordings
OBD-II
Select Vehicle
Tue, 10 May 2016
Diagnostic
Information
Settings
System Wiring
Diagrams
1. Select System Wiring Diagrams from the Home Screen.
ss02595
Fast Touch Websites -Wiring Diagrams - / 0 http://si0vmc1235.de.bosch.com/nawd-client/app/app/#/11aa3a9c-59bc-81d5-94d0-87fa7e39c396/circuitdiagrams/a1
Wiring Diagrams
Selected vehicle:
2015 / Nissan / Titan / 5.6L (Naturally Aspirated)
Wiring Diagrams
Menu
Wiring Diagrams
System
All
2. Select a wiring diagram to view.
«
Filter displayed text
Air Conditioning: Automatic A/C Circuit
Air Conditioning: Manual A/C Circuit\2 Control Dial System
Air Conditioning: Manual A/C Circuit\3 Control Dial System W/ VBC
Anti-lock Brakes
Anti-theft: Forced Entry Circuit\ Crew Cab
Anti-theft: Forced Entry Circuit\ King Cab
Anti-theft: Immobilizer Circuit
Body Computer
Computer Data Lines
?
2:59
116
MACTOOLS.COM
ss02596
Fast Touch Websites -Wiring Diagrams - / 0 http://si0vmc1235.de.bosch.com/nawd-client/app/app/#/11aa3a9c-59bc-81d5-94d0-87fa7e39c396/circuitdiagrams/a1
Wiring Diagrams
Selected vehicle:
2015 / Nissan / Titan / 5.6L (Naturally Aspirated)
?
Wiring Diagrams Wiring diagram - Air Conditioning: Automatic A/C Circuit
Page 1/2
3
4
2
6
1
YEL
LT BLU
PNK
GRN
WHT/GRN
M
DRIVER
AIR MIX
DOOR MOTOR
(TOP LEFT CENTER
OF HVAC UNIT)
M
1
2
3
5
6
YEL
GRY
PNK
BRN/WHT
PNK/BLU
YEL 11
J/C M04
(UNDER FRONT OF
CENTER CONSOLE)
J/C M02
(LEFT SIDE
OF DASH)
HOT AT
ALL TIMES
19
10A
HOT IN ON
OR START
8
10A
FUSE
BLOCK
(J/B)
(BEHIND
RIGHT END
OF DASH)
3. Use navigation buttons located on the left side of the screen to zoom and rotate wiring diagram.
800.MACTOOLS
117
CUSTOMER SUPPORT
Technical Support
For technical questions on your product, contact 800.MACTOOLS, and select the option for technical support.
Order Information
Contact your local Mac Tools Distributor for replacement parts and accessories.
Repair Service
Please contact Technical Support for troubleshooting and service options before sending any unit in for repair.
To send a unit in for repair, please call 800.MAC TOOLS or contact your local Mac Tools Distributor.
118
MACTOOLS.COM
CUSTOMER SERVICE
We at Mac Tools are committed to our customers, please reference the following phone number for a direct contact to one of our customer technicians. They will be more than happy to help with any service or warranty questions you may have about your power tool.
Mac Tools
505 North Cleveland Avenue
Suite 200
Westerville, Ohio 43082
800.MACTOOLS
MACTOOLS.COM
119
advertisement
Key Features
- Professional scan tool built into a durable AndroidTM tablet
- Up to four hours of battery run time
- Extremely fast boot time and Swift On function
- Wi-Fi and web browser allow full internet access
- Built-in training videos to learn scan tool and vehicle test procedures
- AutoDetectTM alerts technician when repair information is available
- Auto IDTM. Automatically identifies CAN vehicles to quickly set up year, make, model, and engine
- Deep Link In-session to Direct-HitTM for identifix® subscribers
Related manuals
Frequently Answers and Questions
How long is the warranty on the Mac Tools MDT 10?
What is the AutoDetectTM feature?
What is the Auto IDTM feature?
Does the Mac Tools MDT 10 come with built-in training videos?
Can I access the internet with the Mac Tools MDT 10?
advertisement
Table of contents
- 3 INTRODUCTION
- 3 WARRANTY
- 4 SAFETY DEFINITIONS
- 4 SAFETY PRECAUTIONS
- 6 GENERAL INFORMATION
- 6 Introduction
- 7 Handset
- 8 Handset Ports
- 9 Handset Back
- 10 Vehicle Communication Interface (VCI)
- 11 Add-on Hardware Modules (Optional)
- 11 Software Descriptions
- 12 SETUP
- 12 Docking Station
- 13 Battery Charging
- 13 Using the handset
- 14 REGISTRATION
- 18 30 Day Trial
- 19 Provide Power to VCI
- 23 Test Startup and Vehicle Connection
- 23 Adjust Settings
- 30 GLOBAL OBDII APPLICATIONS
- 30 Overview
- 30 Diagnostic Functions
- 32 Data Stream
- 35 DTCs Modes
- 38 Oxygen (O2) Sensors
- 40 Special Tests
- 42 Vehicle Info
- 44 SELECTING VEHICLE
- 44 Auto ID
- 47 Manual Entry
- 50 Recent
- 53 Favorites
- 55 OBD-II
- 56 Heavy Duty
- 60 READ DTCS
- 60 Overview
- 62 Ford/Lincoln/Mercury
- 63 GM/GMC
- 68 DATA STREAM
- 68 Overview
- 78 SPECIAL TESTS
- 78 Overview
- 82 DIAGNOSTIC INFORMATION
- 82 Overview
- 94 MAINTENANCE TESTS
- 98 ALL SYSTEM DTC SCAN
- 98 Overview
- 102 Browser
- 102 Overview
- 104 AUTOMATED SYSTEM TEST
- 104 Overview
- 111 VIEW SAVED TESTS
- 111 Overview
- 114 VIEW DATA STREAM RECORDINGS
- 114 Overview
- 116 SYSTEM WIRING DIAGRAMS
- 116 Overview
- 118 CUSTOMER SUPPORT
- 118 Technical Support
- 118 Order Information
- 118 Repair Service
- 119 CUSTOMER SERVICE