advertisement
SDR-H90&80EP-LSQT1467_mst.book 1 ページ 2008年12月2日 火曜日 午後2時32分
Basic Operating Instructions
SD Card/Hard Disk Video Camera
Model No.
SDR-H90
SDR-H80
Before use, please read these instructions completely.
Please also refer to Operating
Instructions (PDF format) recorded on the CD-ROM containing the Operating
Instructions (supplied).
You can learn about advanced operation methods and check the Troubleshooting.
LSQT1467 A
EP
until
2008/12/26
SDR-H90&80EP-LSQT1467_mst.book 2 ページ 2008年12月2日 火曜日 午後2時32分
Information for Your Safety
WARNING:
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR PRODUCT
DAMAGE,
≥ DO NOT EXPOSE THIS APPARATUS TO
RAIN, MOISTURE, DRIPPING OR
SPLASHING AND THAT NO OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE
APPARATUS.
≥ USE ONLY THE RECOMMENDED
ACCESSORIES.
≥ DO NOT REMOVE THE COVER (OR
BACK); THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The socket outlet shall be installed near the equipment and easily accessible.
The mains plug of the power supply cord shall remain readily operable.
To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from AC receptacle.
∫ EMC Electric and magnetic
compatibility
This symbol (CE) is located on the rating plate.
Use only the recommended accessories.
≥ Do not use any other AV cables and USB cables except the supplied one.
≥ When you use the cable which are sold separately, please make sure to use the one whose length is less than 3 meters.
CAUTION!
≥ DO NOT INSTALL OR PLACE THIS UNIT
IN A BOOKCASE, BUILT-IN CABINET OR
IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL
VENTILATED. TO PREVENT RISK OF
ELECTRIC SHOCK OR FIRE HAZARD
DUE TO OVERHEATING, ENSURE THAT
CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE
VENTILATION VENTS.
≥ DO NOT OBSTRUCT THE UNIT’S
VENTILATION OPENINGS WITH
NEWSPAPERS, TABLECLOTHS,
CURTAINS, AND SIMILAR ITEMS.
≥ DO NOT PLACE SOURCES OF NAKED
FLAMES, SUCH AS LIGHTED CANDLES,
ON THE UNIT.
≥ DISPOSE OF BATTERIES IN AN
ENVIRONMENTALLY FRIENDLY
MANNER.
≥ Keep the Memory Card out of reach of children to prevent swallowing.
Product Identification Marking is located on the bottom of units.
2
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 3 ページ 2008年12月2日 火曜日 午後2時32分
∫ Caution for use
Keep the SD Card/Hard Disk Video Camera as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.).
≥ If you use the SD Card/Hard Disk Video
Camera on top of or near a TV, the pictures and sound on the SD Card/Hard Disk Video
Camera may be disrupted by electromagnetic wave radiation.
≥ Do not use the SD Card/Hard Disk Video
Camera near cell phones because doing so may result in noise adversely affecting the pictures and sound.
≥ Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields created by speakers or large motors.
≥ Electromagnetic wave radiation generated by microprocessors may adversely affect the SD
Card/Hard Disk Video Camera, disturbing the pictures and sound.
≥ If the SD Card/Hard Disk Video Camera is adversely affected by electromagnetic equipment and stops functioning properly, turn the SD Card/Hard Disk Video Camera off and remove the battery or disconnect AC adaptor.
Then reinsert the battery or reconnect AC adaptor and turn the SD Card/Hard Disk Video
Camera on.
Do not use the SD Card/Hard Disk Video
Camera near radio transmitters or highvoltage lines.
≥ If you record near radio transmitters or high-voltage lines, the recorded pictures and sound may be adversely affected.
About connecting to a TV or other video devices.
≥ Do not use any other AV cables except the supplied one.
About connecting to a PC or a printer.
≥ Do not use any other USB cables except the supplied one.
∫ Information for Users on
Collection and Disposal of Old
Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/
EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the
European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European
Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
Cd
Note for the battery symbol
(bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the
Directive for the chemical involved.
3
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 4 ページ 2008年12月2日 火曜日 午後2時32分
∫ Indemnity concerning recording
content
The manufacturer shall in no event be liable for the loss of recordings due to malfunction or defect of this unit, its accessories or recordable media.
∫ Carefully observe copyright laws
Recording of pre-recorded tapes or discs or other published or broadcast material for purposes other than your own private use may infringe copyright laws. Even for the purpose of private use, recording of certain material may be restricted.
∫ Cards that you can use with this
unit
SD Memory Card and SDHC Memory Card
≥ 4 GB or more Memory Cards that do not have the SDHC logo are not based on SD Memory
Card Specifications.
≥ Refer to page 15 for more details on SD cards.
∫ For the purposes of these
operating instructions
≥ SD Memory Card and SDHC Memory Card are referred to as the “SD card”.
≥ Pages for reference are indicated by an arrow, for example: l 00
≥ These operating instructions are designed for use with models SDR-H90 and SDR-H80.
Pictures may be slightly different from the original.
jThe illustrations used in these operating instructions show model SDR-H80, however, parts of the explanation refer to different models.
jDepending on the model, some functions are not available.
jFeatures may vary, so please read carefully.
∫ Licenses
≥ SDHC Logo is a trademark.
≥ U.S. Patent Nos. 6,836,549; 6,381,747;
7,050,698; 6,516,132; and 5,583,936.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
≥ Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
≥ Microsoft
®
, Windows
®
, Windows Vista
®
,
DirectDraw
®
, DirectSound
® and DirectX
®
are either registered trademarks or trademarks of the Microsoft Corporation in the United States and/or other countries.
≥ Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
≥ IBM, PC/AT and PowerPC are registered trademarks of International Business Machines
Corporation of the U.S.
≥ Intel
®
, Core
™
, Pentium
®
and Celeron
® are the registered trademarks or trademarks of the
Intel Corporation in the United States and other countries.
≥ YouTube and the YouTube logo are the registered trademarks or trademarks of
YouTube LLC.
≥ Macintosh and Mac OS are either registered trademarks or trademarks of Apple Inc. in the
United States and/or other countries.
≥ Other names of systems and products mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned.
4
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 5 ページ 2008年12月2日 火曜日 午後2時32分
Contents
Information for Your Safety ...........................2
Accessories.....................................................6
Preparation
Before using
[1] Parts identification and handling ....... 7
[2] Power supply ..................................... 10
Charging the battery ............................ 10
Inserting the battery............................. 11
Charging time and recordable time ..... 12
Connecting to the AC outlet................. 13
[3] About HDD and SD cards ................. 14
HDD handling ...................................... 16
Access lamp ........................................ 16
[4] Inserting/removing an SD card ........ 17
Setup
[1] Turning the unit on/off
Selecting a mode ............................... 18
[2] Using the menu screen ..................... 19
Language selection ............................. 19
[3] Setting date and time ........................ 20
Recording
Recording
[1] Before recording................................ 21
Intelligent auto mode ........................... 21
[2] Recording motion pictures............... 22
[3] Recording still pictures..................... 23
[4] Recording functions.......................... 24
Zoom in/out function ............................ 24
Optical image stabilizer function.......... 24
Playback
Playback
[1] Motion picture playback ................... 25
[2] Still picture playback......................... 26
Editing
[1] Deleting scenes/files ......................... 27
Deleting scenes/files one at a time...... 27
Deleting multiple scenes/files .............. 27
Media management
[1] HDD and SD card management ....... 28
Formatting HDD .................................. 28
Displaying HDD information ................ 28
Formatting an SD card ........................ 28
Others
Reading the Operating Instructions
(PDF format).................................................. 29
Specifications ............................................... 30
5
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 6 ページ 2008年12月2日 火曜日 午後2時32分
Accessories
Check the accessories before using this unit.
Battery pack
VW-VBG070
≥ The battery is not charged. Be sure to charge the battery before using this unit. (l 10)
AC adaptor
VSK0698
AC cable
K2CQ2CA00006 or
K2CR2DA00004
DC cable
K2GJ2DC00015
AV cable
K2KC4CB00022
USB cable
K1HA05AD0006
Optional accessories
Some optional accessories may not be available in some countries.
AC adaptor (VW-AD21E-K)
Battery pack (lithium/VW-VBG070)
Battery pack (lithium/VW-VBG130)
Battery pack (lithium/VW-VBG260)
Battery pack (lithium/VW-VBG6)
*1
Battery Pack Holder Kit (VW-VH04)
Wide conversion lens (VW-W3707H)
Filter kit (VW-LF37WE)
DVD burner (VW-BN1)
Shoe adaptor (VW-SK12E)
Video DC light (VW-LDC103E) *2
Light bulb for video DC light (VZ-LL10E)
*1 The battery pack holder kit VW-VH04
(optional) is necessary.
*2 The shoe adaptor VW-SK12E (optional) is necessary.
CD-ROM
Software
CD-ROM
LSFT0775
Operating Instructions
6
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 7 ページ 2008年12月2日 火曜日 午後2時32分
Preparation
Before using
1
Parts identification and handling
1 2 3 4 5 6
15
7
1 LCD monitor open part
2 Joystick
3 LCD monitor
8
Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen.
However, this is not a malfunction and does not affect the recorded picture.
4 Web mode button [WEB MODE]
5 When recording: Zoom lever [W/T]
When playing back: Volume lever
[sVOLr]
6 Intelligent auto button [iA]
7 Menu button [MENU]
8 Speaker
9 Delete button [ ]
10 Manual button [MANUAL AF/MF]
11 Optical image stabilizer button
[ , O.I.S.]
12 Audio-video output terminal [A/V]
13 SD Card access lamp [ACCESS]
14 SD Card slot cover [SD CARD]
15 SD card slot
9 10 11 12 13 14
LCD monitor
Pull the LCD monitor out in the direction of the arrow with your fingers.
≥ It can open up to 90o.
≥ It can rotate up to 180o A towards the lens or 90o B towards the opposite direction.
≥ The brightness and colour level of the LCD monitor can be adjusted.
7
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 8 ページ 2008年12月2日 火曜日 午後2時32分
Joystick
Use the joystick to select the recording functions and playback operations, and to operate the menu screen.
Move the joystick up, down, left, or right to select a setting or scene, and then press the joystick to set it.
Attaching the lens cap
(Included in the Filter Kit
(VW-LF37WE; optional))
≥ When the filter kit (VW-LF37WE; optional) is used, protect the lens surface while the unit is not used with the lens cap supplied with the filter kit.
1 Select by moving up, down, left, or right.
2 Set by pressing the centre.
16 17
≥ To attach or remove the lens cap, hold both sides of the lens cap with the tips of your finger and thumb.
18 Grip belt
19 Microphone (built-in, stereo)
Lens cover
For the lens protection, be sure to close the lens cover when not in use.
Slide open/close switch for the lens cover.
18 19
16 Open/close switch for the lens cover
17 Lens
≥ Attach the MC protector or the ND filter of the
Filter Kit (VW-LF37WE; optional) or the wide conversion lens (VW-W3707H; optional) in front of the lens.
≥ When using the wide conversion lens, if the magnification exceeds 20k then the image quality is degraded.
≥ The tele conversion lens cannot be used.
Grip belt
Adjust the belt length and the pad position.
1 Flip the belt.
2 Adjust the length.
3 Replace the belt.
8
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 9 ページ 2008年12月2日 火曜日 午後2時32分
20 21 22 23
27
24 25 26
20 HDD access lamp [ACCESS HDD]
21 Status indicator
22 Mode dial
23 Recording start/stop button
24 Battery holder
25 DC input terminal [DC IN]
≥ Always use the supplied AC adaptor or a genuine Panasonic AC adaptor (VW-AD21E-K; optional).
26 USB terminal [ ]
27 Tripod receptacle
28 Battery release lever [BATTERY]
Tripod receptacle
This is a hole for attaching the unit to the optional tripod.
28
9
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 10 ページ 2008年12月2日 火曜日 午後2時32分
Preparation
Before using
2
Power supply
∫ About batteries that you can use with this unit
The battery that can be used with this unit is supplied battery/VW-VBG070/VW-VBG130/
VW-VBG260/VW-VBG6.
≥ This unit has a function to distinguish the batteries that can be used, and the batteries
(VW-VBG070/VW-VBG130/VW-VBG260/VW-VBG6) are compatible with this function. (The batteries that are not compatible to this function cannot be used.)
≥ The battery pack holder kit VW-VH04 (optional) is necessary if using VW-VBG6.
It has been found that counterfeit battery packs which look very similar to the genuine product are made available to purchase in some markets. Some of these battery packs are not adequately protected with internal protection to meet the requirements of appropriate safety standards. There is a possibility that these battery packs may lead to fire or explosion.
Please be advised that we are not liable for any accident or failure occurring as a result of use of a counterfeit battery pack. To ensure that safe products are used we would recommend that a genuine Panasonic battery pack is used.
Charging the battery
When this unit is purchased, the battery is not charged. Charge the battery before using this unit.
Important:
If the DC cable is connected to the AC adaptor, the battery will not charge. Remove the DC cable from the AC adaptor.
Charging lamp [CHARGE] A
Lights up:
Charging (l 12, Charging time)
Goes off:
Charging completed
Flashing:
≥ When the battery temperature is excessively high or low, the lamp flashes and the charging time will be longer than normal.
≥ Remove dirt, foreign objects or dust on the terminals of the battery or the AC adaptor.
If the lamp is still flashing, something may be wrong with the battery or AC adaptor.
Contact your dealer.
1
Connect the AC cable to the AC adaptor and the AC outlet.
2
Insert the battery on the AC adaptor by aligning the arrows.
≥ We recommend using Panasonic batteries. ( l 6, 12)
≥ If you use other batteries, we cannot guarantee the quality of this product.
10
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 11 ページ 2008年12月2日 火曜日 午後2時32分
Inserting the battery
Removing the battery
While sliding the BATTERY lever, slide the battery to remove it.
Push the battery against the battery holder and slide it until it clicks.
≥ Hold the battery with your hand so that it does not fall.
≥ Be sure to set the mode dial to OFF and check that the status indicator is off before removing the battery.
≥ Do not heat or expose to flame.
≥ Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period of time with doors and windows closed.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC or incinerate.
11
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 12 ページ 2008年12月2日 火曜日 午後2時32分
Charging time and recordable time
∫ Charging time
≥ Temperature: 25 oC/humidity: 60%
Battery model number
Supplied battery/VW-VBG070
(optional)
VW-VBG130 (optional)
VW-VBG260 (optional)
VW-VBG6* (optional)
Voltage/Capacity (Minimum)
7.2 V/725 mAh
7.2 V/1250 mAh
7.2 V/2500 mAh
7.2 V/5400 mAh
Charging time
1 h 35 min
2 h 35 min
4 h 40 min
9 h 25 min
≥ If the temperature is higher or lower than 25 oC, the charging time will become longer.
∫ Recordable time
≥ Temperature: 25 oC/humidity: 60%
Battery model number
Voltage/
Capacity
(Minimum)
Recording destination
Recording mode
Supplied battery/
VW-VBG070
(optional)
7.2 V/
725 mAh
[HDD]
XP
SP/LP
[SD]
XP/SP/LP
XP
VW-VBG130
(optional)
7.2 V/
1250 mAh
[HDD]
[SD]
SP/LP
XP/SP/LP
VW-VBG260
(optional)
7.2 V/
2500 mAh
[HDD]
XP
SP/LP
[SD]
XP/SP/LP
XP
VW-VBG6*
(optional)
7.2 V/
5400 mAh
[HDD]
SP/LP
[SD]
XP/SP/LP
* The battery pack holder kit VW-VH04 (optional) is necessary.
Maximum continuously recordable time
1 h 50 min
1 h 55 min
2 h
2 h 55 min
3 h
3 h 10 min
5 h 20 min
5 h 35 min
5 h 50 min
13 h 20 min
13 h 50 min
14 h 30 min
Actual recordable time
55 min
1 h
1 h 5 min
1 h 30 min
1 h 35 min
1 h 45 min
2 h 50 min
2 h 55 min
3 h 15 min
7 h
7 h 20 min
8 h 5 min
≥ These times are approximations.
≥ The actual recordable time refers to the recordable time when repeatedly starting/stopping recording, turning the unit on/off, moving the zoom lever, etc.
≥ The recordable times will vary depending on the status of use. Be aware that the operating time of the battery will become shorter in low temperatures. We recommend charging a spare battery for use when recording.
≥ The batteries heat up after use or charging. This unit will also heat up while being used. This is not a malfunction.
12
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 13 ページ 2008年12月2日 火曜日 午後2時32分
Battery capacity indication
≥ The display changes as the battery capacity reduces.
If there is less than 3 minutes remaining, then
# # # #
will become red. If the battery discharges, then ( ) will flash.
≥ The remaining battery capacity is displayed when using the Panasonic battery that you can use for this unit. It may take time to display the remaining battery capacity. The actual time can vary depending on your actual use.
≥ The maximum amount of remaining battery capacity able to be indicated is 9 hours 59 minutes. If the actual remaining time exceeds 9 hours 59 minutes, the indication will stay green and will not change until the remaining time falls below 9 hours 59 minutes.
≥ When turning the mode dial to switch modes, the time indication will turn off momentarily in order to recalculate the remaining battery capacity time.
≥ When using the AC adaptor or batteries made by other companies, the remaining battery capacity will not be shown.
Connecting to the AC outlet
The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always
“live” as long as the AC adaptor is connected to an electrical outlet.
Important:
While the DC cable is connected to the AC adaptor, the battery will not charge.
1
Connect the AC cable to the AC adaptor and the AC outlet.
2
Connect the DC cable to the AC adaptor.
3
Connect the DC cable to this unit.
≥ Do not use the AC cable with any other equipment as it is designed only for this unit.
Also, do not use the AC cable from other equipment with this unit.
13
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 14 ページ 2008年12月2日 火曜日 午後2時32分
Preparation
Before using
3
About HDD and SD cards
This unit can be used for recording motion pictures and still pictures to the internal HDD and an SD card.
Internal HDD
(Hard Disk Drive)
SD Memory Card
SDHC
Memory
Card
Display on the screen
Indication in these instructions
Capacity
[HDD] [SD]
80 GB
60 GB
*1
(SDR-H90)
*2
(SDR-H80)
8 MB/
16 MB
32 MB/
64 MB/
128 MB
256 MB/
512 MB/
1 GB/
2 GB
4 GB/
6 GB/
8 GB/
12 GB/
16 GB/
32 GB
Functions
Recording motion pictures
¥
–
¥
*3
¥
Recording still pictures
Creating playlists
¥ ¥
¥ –
¥: applicable –: not applicable
*1 The 80 GB hard drive utilizes a portion of the storage space for formatting, file management and other purposes. 80 GB is 80,000,000,000 bytes. Usable capacity will be less.
*2 The 60 GB hard drive utilizes a portion of the storage space for formatting, file management and other purposes. 60 GB is 60,000,000,000 bytes. Usable capacity will be less.
*3 Cannot be guaranteed in operation.
14
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 15 ページ 2008年12月2日 火曜日 午後2時32分
About SD cards that you can use for motion picture recording
We recommend using SD cards conforming to Class 2 or higher of the SD Speed Class Rating or the following SD cards made by Panasonic for motion picture recording. (If another kind of SD card is used, the recording may suddenly stop during motion picture recording.)
256 MB
512 MB
1 GB
2 GB
4 GB
6 GB
8 GB
12 GB
16 GB
32 GB
High Speed SD
Memory Card
RP-SDH256
RP-SDK512
RP-SDH01G
RP-SDK02G
–
–
–
–
–
–
Class 2 SD/SDHC
Memory Card
RP-SDR256
RP-SDR512
RP-SDR01G
RP-SDR02G
RP-SDR04G
–
–
–
–
–
Class 4 SD/SDHC
Memory Card
–
–
–
RP-SDM02G
RP-SDM04G
RP-SDM06G
–
RP-SDM12G
–
–
≥ Operation in motion picture recording is not guaranteed with the following SD cards.
jSD cards from 32 MB to 128 MB jSD cards from 256 MB to 32 GB other than the ones mentioned above
SD card handling
Class 6 SD/SDHC
Memory Card
–
–
RP-SDV01G
RP-SDV02G
RP-SDV04G
–
RP-SDV08G
–
RP-SDV16G
RP-SDV32G
≥ Do not touch the terminals on the back of the card.
≥ Do not expose the terminals of the card to water, garbage or dust.
≥ Do not leave SD card in the following areas: jIn direct sunlight.
jIn very dusty or humid areas.
jNear a heater.
jLocations susceptible to significant difference in temperature (condensation can occur).
jWhere static electricity or electromagnetic waves occur.
≥ To protect SD cards, keep them in their cases when not being used.
≥ Electrical noise, static electricity, or failure of this unit or the SD card may damage or erase the data stored on the SD card. We recommend saving the SD data to a PC.
≥ Keep the Memory Card out of reach of children to prevent swallowing.
15
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 16 ページ 2008年12月2日 火曜日 午後2時32分
HDD handling
This unit has an internal HDD. The HDD is a precision instrument so take care when handling it.
∫ Do not cause any vibrations or
impacts to this unit
Impact may cause the HDD to malfunction.
≥ The HDD may no longer be recognised by this unit.
≥ Recording may no longer be possible on the HDD.
≥ Playback of contents stored on HDD may no longer be possible.
During recording or playback:
≥ Do not cause vibrations or any impact to the HDD.
∫ Do not drop this unit
The HDD may be damaged if this unit receives a strong impact due it to being dropped etc.
This unit has a drop detection function to protect the HDD from impact if the unit is dropped. If it detects that the unit has been dropped during motion picture recording, the HDD protection operation sound may be recorded. Also if it detects that the unit is being continuously dropped, recording or playback may stop.
∫ Take note of the temperature of
this unit
It may no longer be possible to record or playback if the temperature of this unit is too high or low. A warning message will appear on this unit’s LCD monitor if an irregularity in the temperature is detected.
∫ Do not use the unit in a low
pressure area
The HDD may be damaged if you use this unit where the altitude is more than 3000 m.
∫ Back up important recorded data
to protect it
Save recorded data periodically on a PC, DVD disc, etc. for backup purposes.
If the HDD fails, the recorded data cannot be repaired.
∫ Notes for recording
Images may not be recorded properly to the HDD near high-volume speakers due to the vibration from the speakers. In such cases, record in a location away from the speakers or use an SD card.
∫ About disposing of or giving
away this unit
Read the Operating Instructions (PDF format)
∫ Indemnity about recorded
content
Panasonic does not accept any responsibility for damages directly or indirectly due to any type of problems that result in loss of recording or edited content, and does not guarantee any content if recording or editing does not work properly. Likewise, the above also applies in a case where any type of repair is made to the unit (including any other non-
HDD related component).
Access lamp
A HDD access lamp [ACCESS HDD]
≥ When this unit accesses the HDD, the lamp lights up.
≥ When lamp is on, do not sExpose the unit to strong vibrations or
impacts
sOperate the mode dial sRemove the battery or disconnect the AC
adaptor
≥ Performing the above while lamp is on may result in damage to data/HDD or this unit.
However, the access lamp is supposed to light up while rotating the dial to select a mode. In this case, there is no problem.
B SD card access lamp [ACCESS]
≥ When this unit accesses the SD card, the lamp lights up.
≥ When lamp is on, do not sOpen the SD card slot cover and remove
the SD card
sOperate the mode dial sRemove the battery or disconnect the AC
adaptor
≥ Performing the above while lamp is on may result in damage to data/SD card or this unit.
However, the access lamp is supposed to light up while rotating the dial to select a mode. In this case, there is no problem.
16
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 17 ページ 2008年12月2日 火曜日 午後2時32分
Preparation
Before using
4
Inserting/removing an SD card
Caution:
If the SD card is inserted or removed while the power is on, this unit may malfunction or the data recorded on the SD card may be lost.
A Label side
1
Rotate the mode dial to OFF.
≥ Check that the status indicator has gone off.
2
Open the LCD monitor and then open the SD card slot cover.
3
Insert/remove the SD card.
≥ Press the SD card straight in as far as it will go.
≥ Press the centre of the SD card and then pull it straight out.
4
Securely close the SD card slot cover.
17
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 18 ページ 2008年12月2日 火曜日 午後2時32分
Preparation
Setup
1
Turning the unit on/off
Selecting a mode
Rotate the mode dial to switch to recording, playback or power OFF.
≥ Rotate the mode dial while at the same time pressing in the lock release button
A if changing from OFF to another mode.
≥ Align with the status indicator B.
While pressing the lock release button, set the mode dial to , ,
or to turn on the power.
The status indicator lights and the power turns on.
≥ When the unit is turned on for the first time, a message asking you to set the date and time will appear. Select [YES] and set the date and time. (l 20)
To turn off the power
Set the mode dial to OFF.
≥ The status indicator goes off and the power turns off.
Video recording mode (l 22)
Video playback mode (l 25)
Picture recording mode (l 23)
Picture playback mode (l 26)
OFF
How to turn the power on and off with the LCD monitor
When the mode dial is set to or , the power can be turned on and off with the LCD monitor.
∫ To turn on
Open the LCD monitor.
The status indicator lights.
∫ To turn off
Close the LCD monitor.
The status indicator goes off.
≥ When quick start is set to [ON], the status indicator flashes green. To turn off the power immediately after closing the LCD monitor, set quick start to [OFF].
Set the mode dial to OFF when this unit is not being used.
18
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 19 ページ 2008年12月2日 火曜日 午後2時32分
Preparation
Setup
2
Using the menu screen
ENTER
4
Select the desired setting, then press the joystick to enter the selection.
MENU
1
Press the MENU button.
The menu displayed differs depending on the position of the mode dial.
2
Select the desired top menu, then move the joystick right or press the joystick.
3
Select the submenu item, then move the joystick right or press the joystick.
To get back to the previous screen
Move the joystick left.
To exit the menu screen
Press the MENU button.
≥ Do not switch the mode dial when the menu is displayed.
≥ The menu screen does not appear during recording or playing. You cannot start other operations while the menu screen is displayed.
Language selection
You can select the language displayed on the screen.
1
Press the MENU button, then select [LANGUAGE] and press the joystick.
2
Select [English] and press the joystick.
19
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 20 ページ 2008年12月2日 火曜日 午後2時32分
Preparation
Setup
3
Setting date and time
When the unit is turned on for the first time, a message asking you to set the date and time will appear.
Select [YES] and press the joystick. Perform steps 2 and 3 below to set the date and time.
¬Rotate the mode dial to select
or .
1
Select the menu. (l 19)
[BASIC]
# [CLOCK SET] # [YES]
∫ Changing the date format
Select the menu. (l 19)
[SETUP]
# [DATE FORMAT] # desired
display style
2
Select the date or time, then adjust the desired value with the joystick.
Display style
[Y/M/D]
Screen display
2009.11.15
[M/D/Y] 11.15.2009
[D/M/Y] 15.11.2009
≥ The year will change as follows:
2000, 2001, ..., 2099, 2000, ...
≥ The 24-hour system is used to display the time.
≥ [
] appears on the right top of the screen when [SET WORLD TIME] is set to [HOME], while [ ] appears when it is set to
[DESTINATION].
3
Press the joystick to enter the selection.
≥ The clock function starts at [00] seconds when the joystick is pressed.
4
Press the MENU button to finish the setting.
≥ Check the date and time displayed.
∫ Changing the date and time display mode
Select the menu. (l 19)
[SETUP]
# [DATE/TIME] # desired display
style
[DATE] [D/T] [OFF]
≥ To set summer time, select the summer time in
[HOME] for [SET WORLD TIME] after setting the clock.
≥ The date and time function is driven by a builtin lithium battery.
≥ If the time display is [- -], the built-in lithium battery needs to be charged. Use the following steps to charge the battery, and then set the date and time.
To recharge the built-in lithium battery
Connect the AC adaptor or insert the battery to the unit, and the built-in lithium battery will be recharged. Leave the unit as it is for approx.
24 hours and the battery will save the date and time for approx. 6 months. (Even if the mode dial is set to OFF, the battery is still being recharged.)
15.11.2009
20
LSQT1467 (ENG)
15.11.2009 12:34
SDR-H90&80EP-LSQT1467_mst.book 21 ページ 2008年12月2日 火曜日 午後2時32分
Recording
Recording
1
Before recording
Intelligent auto mode
It will make an optimal setting automatically depending on the objects and recording conditions.
¬Rotate the mode dial to select
or .
Intelligent auto button
Press this button to switch on/off the intelligent auto mode.
It is automatically set to the following modes depending on the objects and recording conditions.
Mode
Portrait
Scene/Effect
When the object is a person
Scenery
Faces are detected automatically, and the brightness is adjusted so it is recorded clearly.
Recording outdoors
Spotlight
The whole landscape will be recorded vividly without whiting out the background sky, which may be very bright.
Under a spotlight
Very bright object is recorded clearly.
Low light Dark room or twilight
It can record clearly even in a dark room or twilight.
Mode
Normal
Scene/Effect
Other situations
Brightness and colour balance are adjusted automatically for clear image.
≥ Due to conditions, a different mode may be identified for the same subject.
≥ Modes are selected automatically by the unit, so it may not choose desired mode depending on the recording conditions.
≥ Brightness may change suddenly or flicker when set to on.
≥ Optical image stabilizer function ( l 24) is set to on in all modes.
≥ If this is turned to on, the guideline function is disabled.
∫ When the intelligent auto mode is
set to off
The auto mode icon [
AUTO
] appears.
Colour balance (white balance) and focusing will be adjusted automatically.
Depending on the brightness of the subject etc., the aperture and shutter speed are automatically adjusted for optimum brightness.
(When set to the video recording mode:
The shutter speed is adjusted to a maximum of
1/350.)
≥ Colour balance and focus may not be adjusted automatically depending on light sources or scenes. If so, manually adjust these settings.
21
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 22 ページ 2008年12月2日 火曜日 午後2時32分
Recording
Recording
2
Recording motion pictures
[HDD] [SD]
≥ Open the lens cover before turning the unit on.
1
Rotate the mode dial to select and open the LCD monitor.
2
Select the recording destination
by the menu. (l 19)
[MEDIA SELECT]
# [HDD] or
[SD CARD]
3
Press the recording start/stop button to start recording.
To end the recording
Press the recording start/stop button again.
≥ [¥] and [;] are red during recording. Do not move this unit until [;] is green.
≥ The images recorded between pressing the recording start/stop button to start recording and pressing it again to pause recording become one scene.
The scene is automatically divided when the recorded data exceeds 3.9 GB. (The recording will continue.)
≥ When about 5 minutes have passed without any operation in recording pause, the unit automatically turns off to save battery life.
To use the unit, turn it on again.
This economy feature can also be set to [OFF].
∫ Screen indications
SP
R 12h45m
A Recording mode
B Selected recording destination
C Remaining time left for recording
When the remaining time is less than
1 minute, [R 0h00m] flashes red.
D Recording time elapsed
Each time the unit enters the recording pause mode, the counter display will be reset to “0h00m00s”.
≥ While motion picture recording is in progress, the recording will not stop even if the LCD monitor is closed.
≥ Do not disconnect the AC adaptor or remove the battery if the unit is in recording mode. This may cause a repair message to appear when powered up again.
22
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 23 ページ 2008年12月2日 火曜日 午後2時32分
Recording
Recording
3
Recording still pictures
[HDD] [SD]
≥ Open the lens cover before turning the unit on.
1
Rotate the mode dial to select and open the LCD monitor.
2
Select the recording destination
by the menu. (l 19)
[MEDIA SELECT]
# [HDD] or
[SD CARD]
3
Press the recording start/stop button.
The unit automatically focuses on the subject at the centre of screen (when auto focus is selected).
∫ Screen indications
0.2
R 12345
A Size of still pictures
B Selected recording destination
C Remaining number of still pictures
Flashes in red when [R 0] appears.
∫ To record still pictures clearly
≥ When zooming in on the subject with a magnification of 4k or higher, it is difficult to reduce the slight shaking from holding this unit by hand. We recommend decreasing the zoom magnification and approaching the subject when recording.
≥ When recording still pictures, hold the unit firmly with your hands and keep your arms stationary at your side so as not to shake the unit.
≥ You can record stable pictures without shaking by using a tripod.
23
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 24 ページ 2008年12月2日 火曜日 午後2時32分
Recording
Recording
4
Recording functions
Zoom in/out function
You can zoom in up to 70k optically.
¬Rotate the mode dial to select
or
.
Move the zoom lever.
[HDD] [SD]
≥ When the zoom magnification is 1k, this unit can focus on a subject approx. 2 cm away from the lens. (Macro function)
≥ When the zoom speed is high, the subject may not be focused easily.
Optical image stabilizer function
Reduces the image shaking (jitter) due to hand movement when recording.
¬Rotate the mode dial to select
or
.
Press the O.I.S. button.
T side:
Close-up recording (zoom in)
W side:
Wide-angle recording (zoom out)
≥ The zoom speed varies depending on the range over which the zoom lever is moved.
≥ If you take your finger off the zoom lever during zoom operation, the operation sound may be recorded. When returning the zoom lever to the original position, move it quietly.
≥ When distant subjects are brought closer, they are focused at about 1.5 m or more.
O.I.S.
O.I.S.: Optical Image Stabilizer
The image stabilizer icon [ ] appears.
To cancel the optical image stabilizer function
Press the O.I.S. button again.
≥ The default setting is on.
≥ Set the intelligent auto mode to off before turning the optical image stabilizer function to off.
≥ When a tripod is used, we recommend that you turn the image stabilizer off.
≥ In the following cases, the image stabilizer function may not work effectively.
jWhen the digital zoom is used jWhen the unit is shaken greatly jWhen you record a moving subject while tracking it
24
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 25 ページ 2008年12月2日 火曜日 午後2時32分
Playback
Playback
1
Motion picture playback
[HDD] [SD]
ENTER
1
1/;: Playback/Pause
::
Skip playback (backward)
9:
Skip playback (forward)
∫:
Stops the playback and shows the thumbnails.
Rotate the mode dial to select
2
Select the playback medium by
the menu. (l 19)
[MEDIA SELECT]
# [HDD] or
[SD CARD]
.
4
Select the playback operation with the joystick.
3
Select the scene to be played back, then press the joystick.
A Scene number (Page number: Except when thumbnails are selected.)
The selected scene is played back, and the operation icon is automatically displayed on the screen.
Selecting pages
≥ Select [ the joystick.
]/[ ] and then press
≥ If you move and hold the joystick left or right, you can fast forward or fast rewind the pages. The thumbnails will disappear, but the scene or page numbers will change.
Release the joystick when you have arrived at the page with the scene you want to display.
25
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 26 ページ 2008年12月2日 火曜日 午後2時32分
Playback
Playback
2
Still picture playback
[HDD] [SD]
ENTER
1/;: Slide show start/pause.
2;: Plays back the previous picture.
;1: Plays back the next picture.
∫:
Stops the playback and shows the thumbnails.
1
Rotate the mode dial to select .
2
Select the playback medium by
the menu. (l 19)
[MEDIA SELECT]
# [HDD] or
[SD CARD]
3
Select the file to be played back, then press the joystick.
The selected file is played back, and the operation icon is automatically displayed on the screen.
4
Select the playback operation with the joystick.
A File number (Page number: When [
[ ] is selected.)
]/
≥ The method for selecting pages is the same as for motion picture playback. (l 25)
26
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 27 ページ 2008年12月2日 火曜日 午後2時32分
Playback
Editing
1
Deleting scenes/files
[HDD] [SD]
Important:
The deleted scenes/files cannot be restored.
ENTER
≥ All the scenes/files on the HDD or SD card except the locked scenes/files will be deleted.
Proceed to step 5.
≥ When the date is selected in motion picture playback, all scenes on the selected date are deleted.
3
(Only when [SELECT] is selected in step 2)
Select the scene/file to be deleted, then press the joystick.
¬
Deleting motion picture scenes:
Rotate the mode dial to select .
¬
Deleting still picture files:
Rotate the mode dial to select .
¬Select [HDD] or [SD CARD] in
[MEDIA SELECT].
Deleting scenes/files one at a time
1
Press the button during playback.
2
When the confirmation message appears
Select [YES], then press the joystick.
Deleting multiple scenes/ files
1
Press the button in the thumbnail display.
2
Select [SELECT] or [ALL] and press the joystick.
(Only when [ALL] is selected)
The selected scene/file is encircled by a red frame.
≥ To unselect the scene/file, press the joystick again.
≥ Up to 50 scenes/files can be selected to be deleted.
4
(Only when [SELECT] is selected in step 2)
Press the button.
5
When the confirmation message appears
Select [YES], then press the joystick.
(Only when [SELECT] is selected in step 2)
To continue deleting other scenes/files
Repeat steps 3 to 5.
To complete editing
Press the MENU button.
27
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 28 ページ 2008年12月2日 火曜日 午後2時32分
Playback
Media management
1
HDD and SD card management
Formatting HDD
[HDD]
This is for initializing HDD.
Please be aware that if the HDD is formatted, then all the data recorded on the HDD will be erased. Store important data on a PC, etc.
¬Rotate the mode dial to select
.
¬Select [HDD] in [MEDIA SELECT].
1
Select the menu. (l 19)
[SETUP]
# [FORMAT HDD] # [YES]
2
When the confirmation message appears
Select [YES], then press the joystick.
≥ When formatting is complete, press the MENU button to exit the message screen.
≥ During formatting, do not turn this unit off.
≥ When you format the HDD, use a battery with sufficient battery power or the AC adaptor.
≥ During formatting, do not cause any vibrations or impacts to this unit.
≥ Perform a physical formatting of the HDD when this unit is to be disposed/transferred.
Displaying HDD information
[HDD]
Information about the space used and remaining on the HDD is displayed.
¬Rotate the mode dial to select
.
¬Select [HDD] in [MEDIA SELECT].
Select the menu. (l 19)
[SETUP]
# [HDD STATUS] # [YES]
To exit the information screen
Press the MENU button.
≥ The unit indicating the capacity of the used and usable area is 1 GB=1,073,741,824 bytes.
≥ (SDR-H90) The 80 GB hard drive utilizes a portion of the storage space for formatting, file management and other purposes. 80 GB is
80,000,000,000 bytes. Usable capacity will be less.
≥ (SDR-H80) The 60 GB hard drive utilizes a portion of the storage space for formatting, file management and other purposes. 60 GB is
60,000,000,000 bytes. Usable capacity will be less.
Formatting an SD card
[SD]
This is for initializing SD cards.
Please be aware that if an SD card is formatted, then all the data recorded on the card will be erased. Store important data on a PC, etc.
¬Select [SD CARD] in
[MEDIA SELECT].
1
Select the menu. (l 19)
[SETUP]
# [FORMAT CARD] # [YES]
2
When the confirmation message appears
Select [YES], then press the joystick.
≥ When formatting is complete, press the MENU button to exit the message screen.
≥ During formatting, do not turn this unit off.
≥ Do not open the card slot cover while formatting. The formatting will stop.
≥ When you format the SD card, use a battery with sufficient battery power or the AC adaptor.
≥ Use this unit to format SD cards. If an SD card is formatted on other products (such as a PC), the time spent for recording may become longer and you may not be able to use the SD card.
≥ Depending on the type of SD card being used, it may take time to format.
28
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 29 ページ 2008年12月2日 火曜日 午後2時32分
Others
Reading the Operating Instructions (PDF format)
≥ You have practised the basic operations introduced in these operating instructions and want to progress to advanced operations.
≥ You want to check the Troubleshooting.
In these kinds of situations refer to Operating
Instructions (PDF format) recorded on the CD-
ROM containing the Operating Instructions
(supplied).
If using the following OS
jWindows 2000 SP4 jWindows XP SP2/SP3 jWindows Vista and SP1
Insert the CD-ROM containing the Operating
Instructions (supplied), click [Adobe(R)
Reader(R)] and then follow the messages on the screen to install.
∫ For Windows
1
Turn the PC on and insert the CD-
ROM containing the Operating
Instructions (supplied).
∫ To uninstall the Operating Instructions
(PDF format)
Delete the PDF file from the “Program
Files\Panasonic\SDR\” folder.
≥ When the contents in the Program Files folder cannot be displayed, click the [Show the contents of this folder] to display them.
2
Select the desired language and then click [Operating
Instructions] to install.
(Example: When an English language OS)
∫ For Macintosh
1
Turn the PC on and insert the CD-
ROM containing the Operating
Instructions (supplied).
2
Open the “Manual” folder in
“LSFT0775” and then copy the
PDF file with the desired language inside the folder.
3
Double click the “H90_H80
Operating Instructions” shortcut icon on the desktop.
∫ When the Operating Instructions (PDF
format) will not open
You will need Adobe Acrobat Reader 4.0 or later or Adobe Reader 6.0 or later to browse or print the Operating Instructions (PDF format).
Download and install a version of Adobe Reader that you can use with your OS from the following
Web Site.
http://www.adobe.com/products/acrobat/ readstep2_allversions.html
3
Double click the PDF file to open it.
29
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 30 ページ 2008年12月2日 火曜日 午後2時32分
Others
Specifications
SD Card/Hard Disk Video Camera
Information for your safety
Power source:
Power consumption:
DC 9.3 V/7.2 V
Recording
3.8 W
Signal system
Recording format
Image sensor
Lens
Filter diameter
Zoom
Monitor
Microphone
Speaker
Standard illumination
Minimum required illumination
Video output level
Audio output level (Line)
USB
CCIR: 625 lines, 50 fields PAL colour signal
SD card: Based on the SD-Video standard
HDD: Independent standard
1/8z CCD image sensor
Total: 800 K
Effective pixels:
Moving picture: 400 K (4:3), 370 K (16:9)
Still picture: 410 K (4:3), 380 K (16:9)
Auto Iris, F1.9 to F5.7
Focal length: 1.5 mm to 105 mm
Macro (Full range AF)
37 mm
70k optical zoom, 100k/3500k digital zoom
2.7z wide LCD monitor (approx. 123 K pixels)
Stereo (with a zoom function)
1 round speaker ‰ 15 mm
1,400 lx
Approx. 6 lx (1/25 in low light mode)
Approx. 2 lx with the colour night view function
1.0 Vp-p, 75 ™
316 mV, 600 ™
Card reader function (No copyright protection support)
HDD reader function
Hi-Speed USB (USB 2.0) compliant
USB terminal Type Mini AB
PictBridge-compliant
USB host function (for DVD burner)
53 mm (W) k 66.3 mm (H) k 107 mm (D)
Dimensions
(excluding the projecting parts)
Mass
Mass in operation
Operating temperature
Operating humidity
Operating altitude
Approx. 310 g
[without battery (supplied) and an SD card (optional)]
Approx. 361 g
[with battery (supplied) and an SD card (optional)]
0 °C to 40 °C
10% to 80%
Less than 3000 m above sea level
30
LSQT1467 (ENG)
SDR-H90&80EP-LSQT1467_mst.book 31 ページ 2008年12月2日 火曜日 午後2時32分
Motion pictures
Recording media
Compression
Recording mode and transfer rate
Audio compression
Maximum number of recordable folders and scenes
SD Memory Card (removable type):
32 MB
*1
/64 MB
*1
/128 MB
*1
/256 MB/512 MB/1 GB/2 GB (FAT12 and
FAT16 format corresponding)
SDHC Memory Card (removable type):
4 GB/6 GB/8 GB/12 GB/16 GB/32 GB (FAT32 format corresponding)
HDD (fixed type): 80 GB
*2
(SDR-H90)/60 GB
*3
(SDR-H80)
MPEG-2
XP: 10 Mbps (VBR)
SP: 5 Mbps (VBR)
LP: 2.5 Mbps (VBR)
SD card: Dolby Digital/MPEG-1 Audio Layer 2
HDD: Dolby Digital
16 bit (48 kHz/2 ch)
SD card: 99 foldersk99 scenes (9801 scenes)
HDD: 999 foldersk99 scenes (98901 scenes)
(When the date changes, a new folder is created and scenes are recorded in this new folder even if the number of scenes in the old folder has not reached 99.)
*1 Cannot be guaranteed in operation.
*2 The 80 GB hard drive utilizes a portion of the storage space for formatting, file management and other purposes. 80 GB is 80,000,000,000 bytes. Usable capacity will be less.
*3 The 60 GB hard drive utilizes a portion of the storage space for formatting, file management and other purposes. 60 GB is 60,000,000,000 bytes. Usable capacity will be less.
Still pictures
Recording media
Compression
Picture size
SD Memory Card (removable type):
8 MB/16 MB/32 MB/64 MB/128 MB/256 MB/512 MB/1 GB/2 GB (FAT12 and FAT16 format corresponding)
SDHC Memory Card (removable type):
4 GB/6 GB/8 GB/12 GB/16 GB/32 GB (FAT32 format corresponding)
HDD (fixed type): 80 GB
*1
(SDR-H90)/60 GB
*2
(SDR-H80)
JPEG (Design rule for Camera File system, based on Exif 2.2 standard), DPOF corresponding
640k480 (4:3), 640k360 (16:9)
*1 The 80 GB hard drive utilizes a portion of the storage space for formatting, file management and other purposes. 80 GB is 80,000,000,000 bytes. Usable capacity will be less.
*2 The 60 GB hard drive utilizes a portion of the storage space for formatting, file management and other purposes. 60 GB is 60,000,000,000 bytes. Usable capacity will be less.
AC adaptor
Information for your safety
Power source:
Power consumption:
DC output:
AC 110 V to 240 V, 50/60 Hz
19 W
DC 9.3 V, 1.2 A (Unit operation)
DC 8.4 V, 0.65 A (Battery charging)
Dimensions
Mass
92 mm (W) k 33 mm (H) k 61 mm (D)
Approx. 115 g
Specifications may change without prior notice.
31
(ENG) LSQT1467
SDR-H90&80EP-LSQT1467_mst.book 32 ページ 2008年12月2日 火曜日 午後2時32分
EU
Panasonic Corporation
Web site: http://panasonic.net
Pursuant to at the directive 2004/108/EC, article 9(2)
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Information for Your Safety
- 6 Accessories
- 10 Charging the battery
- 11 Inserting the battery
- 12 Charging time and recordable time
- 13 Connecting to the AC outlet
- 16 HDD handling
- 16 Access lamp
- 18 Selecting a mode
- 19 Language selection
- 21 Intelligent auto mode
- 24 Zoom in/out function
- 24 Optical image stabilizer function
- 27 Deleting scenes/files one at a time
- 27 Deleting multiple scenes/files
- 28 Formatting HDD
- 28 Displaying HDD information
- 28 Formatting an SD card
- 29 (PDF format)
- 30 Specifications