advertisement
OS900SP Owner’s Manual
Unit shown with Seed Box Lid, sold separately
BILLY GOAT SELF PROPELLED OVERSEEDER
OS900SPS, OS900SPH
Owner's Manual
Accessories
Replacement Parts
Seed Box Lid Kit
A convenient way to enclose the seed box
Chariot Kit
Allows the user to ride behind the unit and decrease fatigue from walking
Reel Kit
Use to replace worn or damaged reels
Blade Kit
Use to replace worn or damaged blades on the reel
P/N 351600 P/N 351601 P/N 351603 P/N 351610
Part No 351513
1
Form No F090712A
OS900SP Owner’s Manual
CONTENTS
SPECIFICATIONS AND SOUND/VIBRATION ___ 3
INSTRUCTION LABELS
PACKING CHECKLIST & ASSEMBLY
4
5
OPERATION 6-7
MAINTENANCE 8
TROUBLESHOOTING____________________________ 9
PARTS LIST____________ 10-21
Part No 351513
2
Form No F090712A
OS900SP Owner’s Manual
Specifications
OS900SPS OS900SPH
Engine:
HP’
9.0 HP (6.7kW) 9.0 HP (6.7kW)
Engine: Model
Engine: Type
Engine: Fuel Capacity
Engine: Oil Capacity
Total Unit Weight:
Max. operating slope
Sound test in accordance with 2000/14/EC
EX270D50021
Subaru
6.4 qt. (6.1 L)
1.06 qt. (1 L)
314# (142 kg)
15 o
104 dB(a)
GX270K1QA2
Honda
5.6 qt. (5.3 L)
1.16 qt. (1.1 L)
323# (147 kg)
20 o
104 dB(a)
Sound at operators ear
Vibration at operator position
84 dB(a)
0.81g (7.95 m/s
2
)
84 dB(a)
0.81g (7.95 m/s
2
)
SOUND
SOUND LEVEL 84 dB(a) at Operators Position
104
Sound tests were conducted in accordance with 2000/14/EC, and were performed on 10-13-2010 under the conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for the sound power level for your model.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Sunny
73 o
F (23 o
C)
11 mph (17 kmh)
South West
Humidity: 27%
Barometric Pressure: 30.34Hg (770 mm Hg)
VIBRATION DATA
VIBRATION LEVEL .81g (7.95m/s
2
)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated vibration test equipment. Tests were performed on 10-13-2010 under the conditions listed below.
General Conditions:
Temperature:
Wind Speed:
Sunny
66 o
F (19 o
C)
3 mph (4.8kph)
Wind Direction:
Humidity:
East
30.2%
Barometric Pressure: 29.9Hg (101.3kpa)
Part No 351513
3
Form No F090712A
OS900SP Owner’s Manual
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT
®
Overseeder. If any labels are damaged or missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL DANGER KEEP HANDS LABEL CLUTCH ITEM #142 LABEL TRANS. RELEASE
AND FEET AWAY
ITEM #145 P/N 400424
P/N 500177 ITEM #146 P/N 351507
LABEL CAUTION GUARDS LABEL DEPTH GAUGE
ITEM #133 P/N 900327 ITEM #59 P/N 351504
LABEL INSTRUCTIONS SEEDER BOX LABEL SEED METERING
ITEM #56 P/N 351501 ITEM #66 P/N 351503
(page 12) (page 12)
.
ENGINE LABELS
SUBARU HONDA
Part No 351513
4
Form No F090712A
OS900SP Owner’s Manual
PACKING CHECKLIST
Your Billy Goat Overseeder is shipped from the factory in one carton, completely assembled.
READ all safety instructions before assembling unit.
TAKE CAUTION
when removing the unit from the box the Handle Assembly is attached to the unit and cables could snag.
PUT OIL IN ENGINE BEFORE STARTING
PARTS BAG &
LITERATURE ASSY
Warranty card P/N-
400972, Owner’s Manual P/N-351513, General Safety and Warnings Manual P/N-
100295, Declaration of Conformity P/N-351508.
Boxing Parts
Checklist
Subaru 9 HP
Honda 9 OHV
Parts bag
P/N-351009
ASSEMBLY
1. UNFOLD the upper handle and slide handle lock loops (item 35) into place to secure the upper handle to the lower.
2. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move height adjust lever to down position, to level engine during checking. See engine manufacturers’ instruction manual.
3. CONNECT spark plug wire.
Part No 351513
5
Form No F090712A
OS900SP Owner’s Manual
OPERATION
FOLDING HANDLE
This unit is equipped with a folding upper handle for easier storage and transportation. The handle can be folded by sliding the handle lock loops (item 35) up. This releases the upper handle, allowing it to be folded over the unit.
ADJUSTING BLADE DEPTH
The depth of the blades can be raised or lowered by rotating the knob located at the rear of the machine. The relative depth of the blades can be gauged by using the depth scale located on the rear of the machine and the bar next to it.
BLADE POSITION & DEPTH CONTROL LEVER
The blades can be raised or lowered into the ground by height adjustment lever at the rear of the unit. The blades will be in their lowered position when the lever is to the left and should be locked in the notch on the right when in transport. The resulting blade depth can be adjusted higher or lower.
See ADJUSTING BLADE DEPTH above.
SLICING TIPS
Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core samples from area to be treated. A core can be cut using a piece of pvc, or metal pipe.
Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to determine the depth of thatch in your yard.
THATCH: Thatch is a dense layer of dead grass, clippings, and roots that builds up over time at the base of the lawn preventing air, water, and fertilizer from reaching the soil. This can cause shallow root development and make a lawn more susceptible to drought and disease.
Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of thatch will keep your lawn in good health.
HEAVY THATCH: Lawns with an excessive amount of thatch will require multiple treatments for effective removal. Trying to remove excessive thatch (greater than 3/4"[19 mm] deep) in one treatment will damage or destroy the living part of the lawn. It is best to remove heavy thatch in seasonal treatments (i.e. spring, and fall).
SLOPES: Rake slopes across not up and down. This is much easier and safer for the operator and is better for the lawn. Raking across will help to reduce runoff during watering and allow the sloped ground to hold more seed, fertilizer, and water. The unit’s maximum operating slope is 35% or 19°.
DEPTH: The wide range of depth adjustment on your unit is provided to allow for blade wear.
Setting the reel deeper will not produce better, or quicker results. The slicing reel should be set even with the ground for verti-slicing work, and set to a maximum 1/2" depth for overseeding jobs. Setting the reel deeper than this will only result in premature wear on the unit (i.e. failed belt). If you desire to work the ground deeper than the above guidelines allow, it should be done gradually in multiple passes..
VERTICUTTING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before starting (i.e. approximately 2" tall for fescue grass). For the best result, Slice/Overseed in criss- cross pattern (See Fig. 1 and See Fig 2).
Fig. 1
Fig. 2
Part No 351513
6
Form No F090712A
OS900SP Owner’s Manual
VERTI-CUTTING OPERATION
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface
(i.e. driveway, or sidewalk).
START ENGINE: See Safety and General Operations manual.
ENGAGE BLADES: Push the Reel Lever down on the operators handle (upper left side).
NOTE: When engaging the blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the blades.
Slowly lower the unit into the turf.
SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should be removed and deposited on top of the healthy grass. Grass runners should be cut and ready for removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).
NOTE: If a large drop in engine RPM occurs, or bounces during operation the blade depth is set
too low.
REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection and removal of the thatch/stems.
OVERSEEDING OPERATION
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft2 [4.5 kg. per 93 m2 ]) Adjustments to the seed drop is located on the front of the unit on the seed dial and should be used in conjunction with the seed chart on the console.
SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm) below a flat surface (i.e. driveway, or sidewalk).
START ENGINE: See Safety and General Operations manual.
ENGAGE REEL AND SEED DROP: Push down on the Reel lever on the operators handle. NOTE:
When engaging the reel in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the reel. Slowly lower the unit into
the turf.
SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in
engine RPM occurs, or bounces during operation the blade depth is set too low.
WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to the seed suppliers directions.
ADJUSTING SEED RATE
To set the seed flow rate, loosen the knob on the indicator dial and set it to the corresponding stop setting on the seed application chart (below or on the console) for the type and amount of seed being used.
INSTRUCTION LABEL P/N 351501
Part No 351513
7
Form No F090712A
OS900SP Owner’s Manual
MAINTENANCE
P
ERIODIC
M
AINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation Every Use (daily)
Inspect for loose, worn or damaged parts.
Check engine oil
Inspect belts
Engine (See Engine Manual)
Grease bearings
Inspect and clean engine air filter
Oil height adjustment linkage
SLICING BLADE WEAR
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any deformed or cracked blades.
Measure the overall diameter of the blade.
5. If blades are warped or the diameter of the blade is 6.75"(171 mm) in length they must be replaced. NOTE: We recommend replacing all the blades at once.
Every 25 Hours
JACKSHAFT BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Place the rear of the unit on blocks.
3. Remove the right rear tire (item 11) and spring (item 155) attaching the housing to the frame.
4. Remove (3) screws (item 114) holding the belt guard (item 19) in place
5. Remove the four screws (item 107) holding the mule drive assembly (item 60) in place.
6. Remove the belt (item 14) by rotating the mule drive pulley and walking it out of the groove, and remove the mule assembly leaving the belt on the transmission.
7. Remove the carriage bolt and nuts holding the right bearing on the jackshaft. Do not remove the bearing and pulley.
8. Remove the belt guard (item 58) by removing the three screws (item 114).
9. Walk the belt off of the crankshaft pulley, and then slide it down the jackshaft to the bearing hole. This will allow the belt to be slid around the mule pulley.
10. Replace the belt by feeding it into the hole and around the pulley that the old one was removed. Make sure it is seated in the jackshaft pulley and then walk it onto the crankshaft pulley making sure it is inside the belt fingers.
11. Reattach the bearing and tighten the hardware securely.
12. Reattach the mule drive and belt, making sure that the belt is seated properly in the transmission pulley and the mule drive assembly.
13. Check the idler tension on the belt when the drive lever is engaged, if it is too loose the spring (item 82) holding the idler arm will need to be replaced.
14. Reattach the guards, tire, spring and spark plug and make sure of proper operation.
MULE BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Place the rear of the unit on blocks.
3. Remove the right rear tire (item 11) and spring (item 155) attaching the housing to the frame.
4. Remove (3) screws (item 114) holding the belt guard (item 19) in place
5. Remove the four screws (item 107) holding the mule drive assembly (item 60) in place. This will allow access to the belt.
6. Remove the belt (item 14) by rotating the mule drive pulley and walking it out of the groove, and then sliding it off of the transmission. Discard old belt.
7. Install new belt using same procedure to walk the belt into the groove, making sure it is seated fully in all pulleys. Reattach the mule drive assembly.
8. With new belt installed pull the drive levers up and make sure the idler pulley puts tension on the cable. The proper adjustment should have the drive lever fully engaged and the belt should be snug on the pulleys.
9. Re-install the belt guard, spring, tire, and then reattach the spark plug.
REEL BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Remove (2) screws (item 38) holding the belt guard (item 20) in place
3. Remove the belt (item 17) by rotating the reel pulley (item16) and walking it out of the groove. Discard old belt.
4. Install new belt using same procedure to walk the belt into the groove, making sure that it is inside the belt fingers.
5. With new belt installed push the reel drive lever down and make sure the idler pulley puts tension on the cable. The proper adjustment should have the blade lever fully engaged and the belt should be snug on the pulleys.
6. Re-install the belt guard and reattach the spark plug.
Part No 351513
8
Form No F090712A
OS900SP Owner’s Manual
Troubleshooting
Problem
Abnormal vibration.
Engine stalls or labors when raking
Engine will not start.
Engine is locked, will not pull over.
Part No 351513
Possible Cause
· Damaged or missing blades. Loose handle bolts. Loose engine bolts
· Blades set too deep into ground.
Solution
· Stop work immediately. Replace any damaged or missing blades. Tighten all loose nuts and bolts.
· Raise blades so that they just touch the ground on a level surface
· Stop switch off (Honda only). Throttle in off position
· Check choke position.
· Out of gasoline or bad, old gasoline.
· Check gasoline.
· Spark Plug wire disconnected.
· Gas valve off.
· Dirty air cleaner.
· Debris locked against reel, or drive pulleys. Engine problem.
· Connect spark plug wire.
· Turn on gas valve.
· Clean or replace air cleaner. Contact a qualified service person.
· Pull spark plug wire and remove debris.
Contact an engine servicing dealer for engine problems.
9
Form No F090712A
OS900SP Owner’s Manual
PARTS DRAWING
1
ITEM NO
1
2
3
4
5
6
DESCRIPTION
SHAFT VERTICUTTING REEL OS900SP
BLADE VERTICUT OS900SP
SPACER PM REEL OS900SP
SPACER HARDENED REEL OS900SP
SPRING DISC 7/8" ID
NUT 7/8"-14 NC
3
SLICING REEL ASSY 351603
2
PART NO.
351111
351305
351261
351297
351298
350341
QTY
1
11
10
1
1
1
4
5
6
Part No 351513 Form No F090712A
10
OS900SP Owner’s Manual
ENGINE ASSEMBLY PARTS DRAWING
Part No 351513
11
Form No F090712A
OS900SP Owner’s Manual
ENGINE ASSEMBLY PARTS LIST
ITEM NO.
1
3
7
18
57
58
78
80
81
82
91
93
95
96
DESCRIPTION
ENGINE HONDA 9HP
ENGINE SUBARU 9HP
ENGINE BASE WA
JACKSHAFT WA
BELT GATES #8954-0298
BRACKET GUARD BELT UPPER
GUARD BELT UPPER OS900SP
PULLEY IDLER 4" OD X 3/8 BORE
ARM IDLER WA UPPER
PULLEY 3.50" OD X 1.00" BORE
SPRING IDLER UPPER
BOLT SHOULDER 1/2" X 2"
NUT LOCK 5/16"-18
WASHER SPLIT LOCK
WASHER LOCK 7/16' S/T MED
OS900SPH OS900SPS
PART NO. QTY PART NO.
430287
-
351100
351107
351211
351203
351116
500113
351113
351296
351275
520031
1
-
1
1
1
1
1
1
1
1
1
1
-
351299
351100
351107
351211
351203
351116
500113
351113
351296
351275
520031
QTY
-
1
1
1
1
1
1
1
8160002 6 8160002 6
8177011 4 8177011 4
8177013 1 8177013 1
99 SCREWCAP 7/16"-20 X 1" HCS GR. 8 W/PATCH 510213
101 SCREWCAP 5/16"-24 X 1" GR 8 W/PATCH 400164
1
4
510213
400164
1
4
1
1
1
1
102 SCREWCAP 3/8"-16 X 1 3/4" HCS ZP
108 WASHER 5/16 FLAT
112 BOLT CARRIAGE 5/16"-18 X 1 1/2" ZP
113 LOCK NUT 3/8-16
8041053
8171003
8024042
8160003
1
8
1
2
8041053
8171003
8024042
8160003
1
8
1
2
114 SCREW SELF TAP 1/4"-20 X 5/8" HWH TYPE F
116 WASHER 3/8" SAE
118 NUT FLANGE 5/16-18 ZP
119 PLATE IMPELLER WASHER PB110
121 SPACER 1.25 OD X 1.010 ID X .938 THK
133 LABEL DANGER
134 SCREWCAP 5/16"-18 X 1 3/4" HCS ZP
135 KEY SQ 1/4" X 1"
196 ENGINE BASE WA OS900SP W/LABELS
199 LABEL MADE IN U.S.A.
890359
8172009 2 8172009 2
350346
850443
351413
900327
3
2
1
2
2
890359
350346
850443
351413
900327
3
2
1
2
2
8041031 5 8041031 5
9201113 1 9201113 1
351608
520116
1
1
351608
520116
1
1
Part No 351513
12
Form No F090712A
OS900SP Owner’s Manual
REEL/REEL DRIVE ASSEMBLY PARTS DRAWING
Part No 351513
13
Form No F090712A
OS900SP Owner’s Manual
REEL/REEL DRIVE ASSEMBLY PARTS LIST
ITEM NO.
3
4
DESCRIPTION
ENGINE BASE WA
HOUSING VERTICUTTER WA OS900SP
5 FRAME SUPPORT OS900SP WA
13 BEARING 3/4" CAST FLANGE W/ZERK
16 PULLEY 0.75" ID X 4" 4L SECTION
17 BELT 4L
20 GUARD REEL BELT OS900SP
21 LABEL DECAL SM CIRCLE
38 SER HEX WASHER 3/8" - 16
41 WASHER 1.125 OD X .344 ID X 10 GA
49 REEL ASSY OS900SP
54 GUARD BEARING REEL OS900SP
55 SPACER SEED BOX AXLE OS900SP
68 DEFLECTOR RUBBER OS900SP
69 BAR CLAMP DEFLECTOR
76 ARM IDLER WA REEL ENGAGE
77 PULLEY
91 BOLT SHOULDER 1/2" X 2"
93 NUT LOCK 5/16"-18
95 WASHER SPLIT LOCK
103 SCREWCAP 5/16-18 X 3 1/2"
104 SCREWCAP 3/8"-16 X 1"
351268
351112
350114
520031
8160002
8177011
8041038
8041050
108 WASHER 5/16" FC
118 NUT FLANGE 5/16-18 ZP
120 NUT LOCK 3/8-16 LT WT THIN ZP
124 SPRING IDLER MULE DRIVE
8171003
350346
8161042
351295
127 SER HEX WASHER FLNG SCREW 5/16"-18 X 3/4" 351264
129 BOLT CARRIAGE 5/16"-18 X 3/4" ZP 8024039
135 KEY 3/16" SQ X 1 1/4"
138 CABLE CLUTCH SEEDING CONTROL
9201080
351221
147 PIN CLEVIS 1/4" X .50"
150 PIN CLIP HITCH 0.051" X 3/4"
187 SCREWCAP 3/8"-16 X 2 1/2" ZP
191 SCREWCAP 5/16"-24 X 1" GR.8 ZP W/PATCH
193 GUARD REEL BELT OS900SP W/LABELS
440124
440193
8041056
400164
351607
OS900SPH OS900SPS
PART NO.
QTY PART NO.
QTY
351100
351101
1
1
351100
351101
1
1
351102
350209
351210
351213
1
2
2
2
351102
350209
351210
351213
2
2
1
2
351117
890456
791080
441150
351012
351206
351408
351269
1
1
2
1
1
1
1
1
351117
890456
791080
441150
351012
351206
351408
351269
1
1
1
1
2
1
1
1
2
4
4
1
2
1
1
1
2
4
5
1
6
4
1
1
1
1
1
1
1
351268
351112
350114
520031
8160002
8177011
8041038
8041050
8171003
350346
8161042
351295
351264
8024039
9201080
351221
440124
440193
8041056
400164
351607
1
1
6
4
5
1
2
4
1
1
1
1
1
2
4
4
1
2
1
1
1
Part No 351513
14
Form No F090712A
OS900SP Owner’s Manual
HANDLE ASSEMBLY PARTS DRAWING
Part No 351513
15
Form No F090712A
OS900SP Owner’s Manual
HANDLE ASSEMBLY PARTS LIST
ITEM NO.
5
DESCRIPTION
FRAME SUPPORT OS900SP WA
28 PLUG TUBE INSERT 1.25 OD
29 HANDLE FOLDING OS900SP
30 BUMPER RECESS
31 BRACKET CONSOLE OS900SP
32 GRIP HANDLE
33 PLUG TUBE INSERT 1" OD
34 CONTROL MAGURA OS900SP
35 LOOP FOLDING HANDLE
52 PIN CLEVIS 3/8 X 2.125
53 RETAINER 3/8" BOLT PUSH NUT
56 LABEL INSTRUCTION OS900SP
70 LEVER CLUTCH/SEED DROP
72 GRIP LEVER 0.125" X 1" X 5" ORANGE
102 SCREWCAP 3/8"-16 X 1 3/4" HCS ZP
107 SCREWCAP 3/8"-16 X 3" HCS ZP
110 BOLT CARRIAGE 3/8"-16 X 2" ZP
113 LOCK NUT 3/8-16 8160003
114 SCREW SELF TAP 1/4"-20 X 5/8" HWH TYPE F 890359
115 WASHER 1/4" SAE
117 LOCK NUT 1/4-20
128 TY WRAP
131 SCREWCAP 1/4"-20 X 1" HCS ZP
136 CABLE SPEED CONTROL RT
137 CABLE SPEED CONTROL LFT
138 CABLE CLUTCH SEEDING CONTROL
140 LABEL LOGO OS900SP
141 BOLT SHOULDER 3/8" X 1 1/4"
142 LABEL CLUTCH BLADE
144 WASHER 3/8 FC
194 BRACKET CONSOLE OS900SP W/LABELS
OS900SPH
PART NO.
QTY PART NO.
QTY
351102 1 351102 1
791056
351406
360298
351208
500267
890132
351209
351231
520120
360279
351501
351212
500379
8041053
8041058
8024062
8172007
8160001
900407
8041006
351219
351271
351221
351500
360284
500177
8171004
351605
1
1
1
1
1
1
2
1
1
1
9
1
4
2
1
2
1
1
2
2
2
2
2
2
1
1
2
1
12
1
OS900SPS
791056
351406
360298
351208
500267
890132
351209
351231
520120
360279
351501
351212
500379
8041053
8041058
8024062
8160003
890359
8172007
8160001
900407
8041006
351219
351271
351221
351500
360284
500177
1
1
1
1
1
1
2
1
1
1
9
1
4
2
1
2
1
1
2
2
2
2
2
2
1
1
2
1
8171004 12
351605 1
Part No 351513
16
Form No F090712A
OS900SP Owner’s Manual
SEED BOX ASSEMBLY PARTS DRAWING
Part No 351513
17
Form No F090712A
OS900SP Owner’s Manual
SEED BOX ASSEMBLY PARTS LIST
ITEM NO.
5
6
DESCRIPTION
FRAME SUPPORT OS900SP WA
SEED BOX WA
10 FRONT WHEEL 14" ASSY
12 BEARING & FLANGETTE ASSY
27 AXLE SEED BOX
44 WHEEL PADDLE SEED WA
45 PLATE SEED CONTROL OS900SP
46 BRACKET CONTROL SEED RATE
48 SPRING EXTENSION .5 X 5.00
55 SPACER SEED BOX AXLE OS900SP
63 SPACER SEED PLATE OS900SP
64 DIAL SEED INDICATOR
65 KNOB 5/16"-18 X 5/8" FLUTED
66 LABEL SEED FLOW RATE
83 CLAMP ROUTING FUEL LINE
100 SCREW 1/4" - 20 X .75 HWH
115 WASHER 1/4" SAE
117 LOCK NUT 1/4-20
791070
8041004
8172007
8160001
125 NUT 5/16"-18 SER HEX WASHER FLNG ZP
129 BOLT CARRIAGE 5/16"-18 X 3/4" ZP 8024039
138 CABLE CLUTCH SEEDING CONTROL 351221
145 LABEL WARNING OPEI 400424
147 PIN CLEVIS 1/4" X .61
148 LABEL BADGING OS900SP
350399
351505
149 WASHER LOCK 5/16" TWISTED TOOTH HEAVY
150 PIN CLIP HITCH 0.051 X 3/4" 440193
151 BOLT CARRIAGE 5/16"-18 X 1 1/4" ZP 8024041
152 SCREWCAP 5/16"-18 X 3/4" HCS ZP 8041026
153 NUT LOCK 5/16"-18 LT WT TH ZP
154 WASHER FENDER 5/16"
8161041
8172020
192 SEED BOX WAS OS900SP W/LABELS 351604
OS900SPH OS900SPS
PART NO.
QTY PART NO.
QTY
351102
351103
1
1
351102
351103
1
1
351013
850232
351223
351105
2
4
1
1
351013
850232
351223
351105
1
1
2
4
351220
351222
351303
351408
351253
351265
400339
351503
1
1
1
2
8
1
1
1
351220
351222
351303
351408
351253
351265
400339
351503
1
1
8
1
1
2
1
1
1
8
8
8
8
8
1
1
1
1
2
1
1
2
1
2
1
791070
8041004
8172007
8160001
350346
8024039
351221
400424
350399
351505
430298
440193
8024041
8041026
8161041
8172020
351604
1
2
1
2
1
2
1
1
1
1
1
8
8
8
8
1
8
Part No 351513
18
Form No F090712A
OS900SP Owner’s Manual
TRANSMISSION ASSEMBLY PARTS DRAWING
Part No 351513
19
Form No F090712A
OS900SP Owner’s Manual
TRANSMISSION ASSEMBLY PARTS LIST
ITEM NO.
2
3
5
7
TRANSAXLE
ENGINE BASE WA
DESCRIPTION
FRAME SUPPORT OS900SP WA
JACKSHAFT WA
11 REAR WHEEL13" X 5" PNEU ASSY
12 BEARING & FLANGETTE ASSY
14 BELT 3L540
15 PULLEY 0.75" ID X 2.75
16 PULLEY 0.75" ID X 4" 4L SECTION
19 GUARD DRIVE BELT OS900SP
22 BRACKET FIXED FRONT FRAME
23 BRACKET RH WEAR PAD OS900SP
24 BRACKET LH WEAR PAD OS900SP
25 WEAR PAD RH OS900SP
26 WEAR PAD LH OS900SP
39 SPACER REAR WHEEL OS900SP
40 WASHER .765 ID X 1.25 OD X .06 THK
41 WASHER 1.125 OD X .344 ID X 10 GA
42 SPEED CONTROL ASSY
43 CONNECTOR SPEED CONTROL
50 LEVER HEIGHT CONTROL WA
51 GRIP LEVER LIFT
59 LABEL DEPTH GAUGE OS900SP
60 MULE ASSY
61 KNOB HAND
62 ROD BYPASS ARM TRANSAXLE
75 SPACER PULLEY JACKSHAFT
79 BRACKET CLUTCH CABLE
84 LOCKNUT WA
85 WASHER .75"
86 STUD 3/4"-10 X 3 3/4 PLTD
90 BOLT SHOULDER 3/8" X 2"
91 BOLT SHOULDER 1/2" X 2"
92 BOLT SHOULDER 3/8" X 1/2"
93 NUT LOCK 5/16"-18
94 RING RETAINING EXTERNAL 3/4"
95 WASHER SPLIT LOCK
97 SCREWCAP 5/16-24 X 1"
102 SCREWCAP 3/8"-16 X 1 3/4" HCS ZP
105 SCREWCAP 5/16"-18 X 3" HCS ZP
106 SCREWCAP 5/16"-18 X 2"
108 WASHER 5/16 FLAT
111 BOLT CARRIAGE 5/16"-18 X 2 3/4" ZP
113 LOCK NUT 3/8-16
114 SCREW SELF TAP 1/4"-20 X 5/8" HWH TYPE F
115 WASHER 1/4" SAE
116 WASHER 3/8" SAE
117 LOCK NUT 1/4-20
8177011
400164
8041053
8041036
8041032
8171003
8024047
8160003
890359
8172007
8172009
8160001
1
2
1
2
1
1
1
1
10
2
-
1
1
1
1
1
1
1
2
1
351415
351200
800227
800109
351272
360153
520031
830528
8160002
850230
850238
441150
351011
351015
351106
840191
351504
-
850154
351304
OS900SPH OS900SPS
PART NO.
QTY PART NO.
QTY
351201
351100
1
1
351201
351100
1
1
351102
351107
351202
850232
351215
1
1
2
4
1
351102
351107
351202
850232
351215
2
4
1
1
1
351214
351210
351118
351226
351227
351228
351229
351230
351409
1
1
1
2
1
1
1
1
2
351214
351210
351118
351226
351227
351228
351229
351230
351409
1
1
1
1
2
1
2
1
1
351415
351200
800227
800109
351272
360153
520031
830528
8160002
850230
850238
441150
351011
351015
351106
840191
351504
-
850154
351304
1
2
1
2
1
1
1
1
10
2
1
-
1
1
1
1
1
1
2
1
4
4
1
4
1
4
6
2
5
10
3
6
8177011
400164
8041053
8041036
8041032
8171003
8024047
8160003
890359
8172007
8172009
8160001
4
4
1
4
1
4
6
2
5
10
3
6
Part No 351513
20
Form No F090712A
OS900SP Owner’s Manual
TRANSMISSION ASSEMBLY PARTS LIST
ITEM NO.
123
DESCRIPTION
BRACKET TORQUE LIMITING
125 NUT 5/16"-18 SER HEX WASHER FLNG ZP
126 SCREW SPOT WELD 5/16"-18 X 3/4 W/PROJ
129 BOLT CARRIAGE 5/16"-18 X 3/4" ZP
131 SCREWCAP 1/4"-20 X 1" HCS ZP
135 KEY 3/16" SQ X 1 1/4"
136 CABLE SPEED CONTROL RT
137 CABLE SPEED CONTROL LFT
OS900SPH
PART NO.
351294
350346
351263
8024039
8041006
9201080
351219
351271
139 SCREWCAP 5/16" SER HEX WSHR FLNG GR. 5 ZP 351264
QTY
1
7
4
5
4
1
1
1
8
OS900SPS
PART NO.
351294
350346
351263
8024039
8041006
9201080
351219
351271
351264
QTY
1
7
4
5
4
1
1
1
8
143 GROMMET 1.25" HOLE
146 LABEL DRIVE RELEASE OS900SP
150 PIN CLIP HITCH 0.051 X 3/4"
153 NUT LOCK 5/16"-18 LT WT TH ZP
154 WASHER FENDER 5/16"
155 SPRING LIFT ASSIST OS900SP
157 SCREW MACH #10-24 X 2" HWF ZP
159 SPACER EYELET SPEED CONTROL OS900SP
160 BEARING 1/2" ID X 1.125 OD
161 BOLT SHOULDER 3/8" X 1 3/4"
162 BRACKET SPEED CONTROL WA OS900SP
163 BELLCRANK SPEED CONTROL WA OS900SP
164 CAM SPEED CONTROL WA
165 BUSHING PIVOT FRAME AE
166 BOLT SHOULDER 5/16" X 1 1/2"
167 SPRING EXTENSION
168 BUSHING 3/8" ID X 1/2" OD X 3/8"
169 SCREWCAP 1/4-20 X 1 3/4 SKT BUT HD
170 NUT LOCK 5/8"-11 LT WT TH ZP
171 WASHER 5/8" SAE
172 SCREWCAP 5/16"-18 X 1" HCS ZP
173 PULLEY IDLER 2.75" OD X 3/8" BORE
174 BRACKET DRIVE BELT WA OS900SP
175 PULLEY 3V GROOVE IDLER
177 BOLT SHOULDER 1/2" X 2"
178 ARM IDLER MULE DRIVE WA OS900SP
179 SPRING IDLER MULE DRIVE OS900SP
180 SCREWCAP 3/8"-16 X 1 1/2" HCS ZP
182 WASHER #10 SAE
183 KEY 3/16" SQ X 2 1/8"
186 SCREWCAP 5/16"-18 X 5" HCS ZP
189 KEY 3/16" SQ X 5/8"
195 FRAME SUPPORT OS900SP WA W/LABELS
197 DRIVE BELT GUARD WA W/LABELS
198 BRACKET BELT GUIDE OSSP
840078
840199
8161046
8172013
8041028
350114
351104
351216
520031
351120
351302
8041052
8172005
9201087
8041042
9201072
351606
351609
351300
520092
351507
440193
8161041
8172020
351254
8059143
351256
351257
351258
351108
351109
351110
360183
500340
800242
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
4
2
1
2
1
2
1
2
2
2
1
2
1
2
1
2
1
1
840078
840199
8161046
8172013
8041028
350114
351104
351216
520031
351120
351302
8041052
8172005
9201087
8041042
9201072
351606
351609
351300
520092
351507
440193
8161041
8172020
351254
8059143
351256
351257
351258
351108
351109
351110
360183
500340
800242
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
4
2
1
2
1
2
1
2
2
2
1
2
1
2
1
2
1
1
Part No 351513
21
Form No F090712A
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement