Super Gym’s Cardio-zone Owner's Manual

SuperSport™ Club

Fold-Away™

OWNER’S MANUAL

Super Gym’s FitnessBlowout.com

2210 S. Sepulveda Blvd.

Los Angeles, CA 90064

Phone: 800-FIT-4-LESS or 800-348-4537

Fax: 310-235-2008

CONGRATULATIONS

C

ongratulations for selecting Super Gym’s CardioZone as your primary source of fitness.

CardioZone treadmills offer many exercise programs that benefit users of all levels and ages. The treadmill is designed to make your workouts more effective and enjoyable.

Please read this manual carefully before using your CardioZone SuperSport™ Club. This will allow you to get a full understanding of all the features that CardioZone treadmills provide. If you have any questions or concerns, please contact Super Gym’s FitnessBlowout.com.

For service, please visit http://www.fitnessblowout.com/service

Register your warranty at http://www.fitnessblowout.com/warranty

Super Gym’s FitnessBlowout.com

2210 S. Sepulveda Blvd.

Los Angeles, CA 90064

Phone: 800-FIT-4-LESS or 800-348-4537

Fax: 310-235-2008

1

2

TABLE OF CONTENTS

SECTION PAGE

1. OVERVIEW DRAWING.......................................................................................... 4

2. IMPORTANT SAFETY INSTRUCTIONS .............................................................. 5

3. GROUNDING INSTRUCTIONS ............................................................................ 6

4. MOTORIZED TREADMILL PRE-ASSEMBLY..................................................... 7

5. ASSEMBLY STEPS ................................................................................................. 8

6. CAUTIONS .............................................................................................................. 11

7. MAINTENANCE ..................................................................................................... 12

8. COMPUTER INSTRUCTION ................................................................................. 13

9. EXPLODED VIEW .................................................................................................. 19

10. TROUBLESHOOTING............................................................................................ 21

11. WARRANTY............................................................................................................ 23

3

OVERVIEW DRAWING

4

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the followings:

Read all instructions before using the treadmill.

DANGER – To reduce the risk of electric shock:

1. Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. An appliance should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.

2. Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.

3. Use this appliance only for its intended use as described in this manual. The manufacturer does not recommend attachments onto the appliance.

4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.

5. Do not carry this appliance by supply cord or use cord as a handle.

6. Keep the cord away from heated surfaces.

7. Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.

8. Never drop or insert any object into any opening.

9. Do not use outdoors.

10. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

11. To disconnect, turn all controls to the off position, than remove plug from outlet.

12. Connect this appliance to a properly grounded outlet only.

Base on content of product. If treadmill has elevation function, it needs to consider the following issues:

13. If the treadmill is foldable, when user finishes using the treadmill, the elevation needs to be back to original position.

14. When user is using the treadmill, it cannot be folded at the same time.

15. The appliance is intended for household use on.

5

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This product must be grounded. If malfunction or breakdown occurs, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER

– Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is product is properly grounded. Do not modify the plug provided with the product - if it will not fit the outlet; have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 110~120volt circuit and has a grounding plug that looks like the plug illustrated in the figure. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.

Figure

Grounding methods

GROUNDED

OUTLET

GROUNDED PIN

6

MOTORIZED TREADMILL PRE-ASSEMBLY

Handrail control button and heart rate strap are optional items in the package

1.Heart rate can be measured in this treadmill. Attach strap to chest during exercise, the heart rate value will display on the PULSE window.

2. Except using the control button on the console, the control button on the handrail can also be used to adjust speed and elevation. The control button on the left handrail is for elevation while the right handrail button is for speed adjustment.

3. Under START/READY condition, if you did not hold grip pulse sensor, then PULSE window will display HP, when you hole the both sides of grip pulse sensor, you will see the PULSE window display the heart rate values.

ITEM Description Qty

A

B

C

Computer set

Frame

Left Upright

1

1

1

E

F

Left Side Cover

Right Side Cover

1

1

I

J

Left handrail cover

Right handrail cover

1

1

K

Bottle holder

1

L Bottle 1

ITEM Description Qty e f

Allen Wrench 5mm

Allen Wrench 6mm

1

1 g SILICON 1

7

ASSEMBLY STEPS

Two people are requested for all assembly steps

(Please note: please follow each step of the assembly instruction.)

1. First tighten the bottom control wire to the plastic wire protection sleeve by pulling the guide wire inside the right upright tube (D). And position it to the side round hole in the right upright tube, then insert the upright tubes (C, D) into the two locations (as the direction arrows shown in the drawing) on the frame. Secure them with bolts (a) and wrench provided.

(P.S. In order to prevent it from danger, two persons are required to assemble the product. Please don't assemble it alone.)

(P.S. Please be aware that one person must hold the upright tubes during the assembly process, just in case, if the tubes fall.)

2. Press the left and right covers (E and F) into position and secure them with 4 (b) bolts as shown.

8

3.Computer assembly:

Please connect the control wires between handrails

(L&R) and computer. Then, put handrail (G and H) according to arrow's direction into the computer (A)

(Ps1. When assembly, make sure that the holes of left, right handrails are in alignment.)

(Ps2. If treadmill has handrail switches function, please be aware to assemble, left side of handrail switch is for incline. Right side of handrail switch is for the speed.)

4. First put the computer on the upper side of frame which just finished assembly from previous step, also connect control wire (upper) attached in computer with control wire (bottom) attached on treadmill, after finished, then have the control wire through the upright, then use bolt (c) to screw tightly according to the drawing on the right.

(Ps1. To avoid to press the control wire of handrail)

(Ps2. In order to prevent it from danger, two people are required to assemble the product.

Please don’t assemble it alone)

9

5. Then, press left screw cover and right screw cover

(I and J) into place and secure them with 2 (d) screws.

6. Finally secure water holder (K) on computer console, then the assembly is completed.

10

CAUTIONS

Note: The cylinder contains high pressure; please avoid contact with any objects.

Note: If the cylinder were damaged, the frame would not be stable and may cause serious danger during folding up process.

This treadmill have the foldable mechanism for storage, when storage must stop all movement (include treadmill belt stop, take off the power cord), then pull out the

Pop-Pin according to arrow’s direction, then lift up the treadmill, until POP=Pin click the hole, then can take the had off, opposite, if want to use treadmill, just pull out the

POP-Pin as the arrow’s direction, then put the treadmill slowly on the floor, until POP-Pin click to the position.

(Ps.1.Prevent from causing dangerous is careful if the kids are around. If want to move the treadmill, must fold the treadmill, let hands hold on rear adjust box, then make the treadmill incline until the roller can be moved smoothly, then can move the treadmill.)

(Ps.2.In order to avoid of dangerous, DO NOT move the treadmill on uneven ground.)

11

MAINTENCE

1. If the Walking Belt tracks off center to the right or left of the deck, first turn the power off. Then use a 6mm wrench (f) to tighten the rear roller bolt on the side of the treadmill toward which the belt is moving. For example, if the belt moves to the left and the deck becomes exposed on the right, tighten the bolt on the left side of the frame. Tighten about 1/4 of turn (clockwise).

If the belt does not move back to the center of the treadmill, make another adjustment to the same bolt.

Once the Walking Belt has been adjusted closer to the center, the treadmill can be started again.

(Ps.1.This action is very important, please follow the above steps.)

(Ps.2. The potion of running belt might not stay precisely in the center with slightly moving the left or right side, and the situation varies with how end-users use and weight of end-users. When end-user use properly, the belt won’t scotch side rails. )

2. It is recommended that the deck be lubricated every

6~12 months according to the frequency of usage. First, use wrench to loosen the bolts in the end caps. Pull up the Walking Belt, dispense the lubricant on the deck, and spread evenly. After lubricating the deck, center the belt, and check the belt tension. Adjust the belt as mentioned in step 1.

(Ps. If the belt happens to slip, follow the above steps and lubricate the running deck.)

SUGGESTED PREVENTIVE MAINTENANCE SCHEDULE IN

ACCORDANCE WITH THE AVERAGE RUNNING SPEED

Measurement Speed Interval

6KM/hr below 1 year

Metric

12KM/hr above

4mile/hr below

3 moths

1 year

English

8mile/hr above 3 moths

Note: This preventive maintenance schedule is only meant for home use. It is suggested to maintain the unit every month for commercial use.

12

Computer Instruction

1. Turn on the On-off switch.

2. Put the safety key into the recess of the console. The beeper will make an alerting sound, meanwhile the dot matrix LED light will be blinking, program light will blink to lead user; this means the treadmill is ready to start. At the ready-start stage, hold the heart rate sensor to measure your heart rate

** The chart below provides different heart rate due to age and amount of exercise：

170

150 166

120 146 162

117 143 157

114 137

111

153

135

108

149

131

105

145

128 140

102 124 136

99 120 132

96 116

93

OVER

MIDDLE

LOW

20 25 30 35 40 45 50 55 60 65 (Age)

3. Press to begin, MANUAL will blink, the treadmill starts with a velocity of 0.5MPH.

While the belt is running, press

、

to accelerate or decelerate the speed of the belt, (or press

、 、 、 、 to choose the speed you want) or press

、

to adjust the inclination angle greater or smaller. (or press

、 、 、 、 、

to choose the angle you want.) Press to stop all motions. (Press

13 once, Time Window will display

STOP, to pause motions of the treadmill and values on the computer console and will remain paused for 60 seconds, after 60 seconds all values will return to zero including the inclination which means its back to the ready-start stage. If press twice, and

II. hold for 3 second for the second attempt, the computer will automatically RESET itself and return to the ready-start motion.)

** Speed Range：0.5~12MPH，each level raise 0.1 MPH.

Angle Range：0~15 %，each level raise 1 %

4. Except using the control button on the console, the control button on the handrail can also be used to adjust speed and elevation. The control botton on the left handrail is for elevation while the right handrail botton is for speed adjustment.

5. At the ready-start condition, press to select other functions:

** If the safety key is not inserted into the recess of the console, then all the windows will display *-----*, this means the treadmill is not ready to start.

**While in motion, if the safety key fell off from the recess console, an alarm will be turned on, and then all motions will be stopped. Reenter the key into the key slot, all values will return to original PROGRAM setting

**At ready state, if the heart rate sensor is not being held by 2 hands, then the PULSE window will display “HP”. If the heart rate sensor is being held, then the heart-beeping rate will be shown on the display

MODE

function key:

1. At the ready-start condition, press

function key, MANUAL LED will be blinking, press

、

or

、

to change to MANUAL、P1~P5 or HRP LED.

2. MANUAL Function：

2.1 While MANUAL light is blinking; press , MANUAL will stop blink, it will continue bright, TIME light will be blinking, now, you can adjust time.

2.2 Press , the motor will operate directly according to installed value 0.5MPH, at the time, press

、

or

、 to adjust the treadmill inclination up/down、speed increase/decrease.

2.3 Dot matrix LED will arrange in a circle according to the running distances. 40 LED make up a circle, mean that

0.25mil in total.

3. P1~P5 Program Control Function (Each PROGRAM control has 12 grades.)

3.1. When MANUAL LED is blinking, press

、

or

、

to select the P1~P5

LED light you want, press to confirm. After enter the program control function, the indicator light will keep blinking.

3.2. At this time, L1 LED will be blinking. This function is used to select violent degree of exercise. (L1~L5) Pres

、

or

、 to select the grade you want. Press to confirm, the LED will keep bright.

3.3. When the grade option confirmation is done, the TIME LED indicator light will be blinking, press

、

or

、 to adjust time, after setting up, press to start the treadmill, or press to reenter the PROGRAM selection mode.

**Pre-set Time：25(min) ; Time Range：5~99(min).

3.4. Press , the motor will operate directly according to installed value, the treadmill program is installed with 12 grades each of speed and inclination, the changing method adapts 12 circulation value, the first degree time setting is 2 minutes, after that each

14

degree for time setting is 1 minute. When time is up, the speed and inclination value will be changed directly. (When operating, press

、

or

、

can control the speed increase/decrease and the inclination angle bigger or smaller directly as your wish.)

3.5. In P1~P5 function setting, if press , the treadmill will start according to program settings. Those didn’t set up any value; the system will adapt the installed (pre-set) value automatically. Press

、

or

、

can change PROGRAM setting, but entering next grade will return to the original PROGRAM setting.

3.6. In each PROGRAM, before L1~L5 begin, they all have 1 minute for warm up. It will start with each LEVEL initial velocity

3.7. P1 and P2 both has its definition as below.：

P1 5K RUN：The pre-set distance in this program is 5000m（3.1mil）. It will be finished, after you run 5000m（3.1mil）, and the treadmill will stop.

Under this mode, jog is the main part purpose.

P2 9 HOLE：The pre-set distance in this program is 3500m（2.17mil）. It will be finished, after you run 3500m（2.17mil）, and the treadmill will stop.

Under this mode, it imitated golf course, and the difficulty is basing on the changes of upgrade or downgrade.

3.8. About pre-set value of P1~P5, refer to following PROGRAM figure：

15

P3 CARDIO

P4 FAT BURN

P5 HILL INTERVALS

16

4. HRP function：(This function must be operated with heart rate strap.) heart rate of runner achieves the preset heart rate, the speed and elevation are kept within a certain range for best training effort.

4.2 When

、

or

、

until the HRP light is blinking, press to confirm. At this time enter the values the program requires.

AGE

、

or

、

to adjust your age. Press to enter next sep.Preset Age： 30Range：13~80, Step is 1

4.4 At this time the PULSE LED is blinking, enter your pulse value. This value is variable according to your age. Please see the following appendix and choose the value you fit.

You can press

、

or

、

to adjust pulse value. If you didn’t do any change, press , and the program will achieve according to the preset value and enter next step.

4.5 TIME indicating light is blinking, enter the time you want by press

、

or

、

, or directly and start exercising without countdown timer

**Adjustable Time range: 5~99 min

** Following provide the HRC option age and HRC pre-set list：

BPM BPM BPM BPM

Age Age Age Age

H

Pre-set

L H

Pre-set

L H

Pre-set

L H

Pre-set

L

13 197 124 124 31 180 113 113 49 162 103 103 67 145 92 92

14 196 124 124 32 179 113 113 50 162 102 102 68 144 91 91

15 195 123 123 33 178 112 112 51 161 101 101 69 143 91 91

16 194 122 122 34 177 112 112 52 160 101 101 70 143 90 90

17 193 122 122 35 176 111 111 53 159 100 100 71 142 90 89

18 192 121 121 36 175 110 110 54 158 100 100 72 141 90 89

19 191 121 121 37 174 110 110 55 157 99 99 73 140 90 88

20 190 120 120 38 173 109 109 56 156 98 98 74 139 90 88

21 189 119 119 39 172 109 109 57 155 98 98 75 138 90 87

22 188 119 119 40 171 108 108 58 154 97 97 76 137 90 86

23 187 118 118 41 170 107 107 59 153 97 97 77 136 90 86

24 186 118 118 42 169 107 107 60 152 96 96 78 135 90 85

25 185 117 117 43 168 106 106 61 151 95 95 79 134 90 85

26 184 116 116 44 167 106 106 62 150 95 95 80 133 90 84

27 183 116 116 45 166 105 105 63 149 94 94

28 182 115 115 46 165 104 104 64 148 94 94

29 181 115 115 47 164 104 104 65 147 93 93

30 181 114 114 48 163 103 103 66 146 92 92

17

III、Body Fat Measurement

1. Press to start the function.

2. Please enter your 『Age』,『Sex』,『Height』and『Weight』

Press

、

or

、

to change the value.

After entering each value, press to confirm, and continue next value setting.

3. While selecting the function, the program requires you to enter the below values:

*Age：Preset 30 Range：13~80 Step = 1

Press to confirm, and go to next setup.

*Sex：Preset 1 (Male) Range :1(Male)、0(Female)

Press

、

or

、

to switch ♂(Male)、♀(Female)

Press to confirm, and go to next setup.

*Height：Preset 5’7” Range：3’11” ~6’7” Step =1”

Press to confirm, and go to next setup.

*Weight：Preset 150LBS Step =2 LBS

Press to confirm.

4. After selecting the above values, hold the heart rate sensor for about 30 seconds.

After 30 seconds, the display will show the “body fat” value.

5. When setting, under the setting items, each items LED indicator light is flashing and display the pre-set value directly, also can change the pre-set values

**The below is a list indicating degrees of fat, it is divided into male and female sections.

Indicator

Sex

1(Male) 0.0~10.0 25.1~30.0

30.1~35.0

0(Female) 0.0~20.0 20.1~35.0

35.1~40.0

40.1~45.0

35.1~

45.1~

18

EXPLODED VIEW

19

Item

1

Computer Console

1-1

Water Holder Tray

2

Bolt

Description

K-299

4

Handler Upper Cover (L) P-1102L

4.1

Handler Upper Cover (R) P-1102R

5

Handler plate NO.2405

6

Bolt

ψ

4x10

7

Handler Bottom Cover (L) P-1099L

7-1

Handler Bottom Cover (R) P-1099R

8

Handler

9

Cap

10

PVC Sponge

ψ

1-1/2"x1.5t

11

Upright (L)

11-1

Upright (R)

12

Support Base

13

Active wheels

14

Spring Washer

15

Spacer

16

Plastic Washer

17

Axile

18

Incline Base

19

Wheels

20

Bolt

21

Bolt

22

Double D Washer

23

Bolt

24

Bot

25

Bolt

26

Plate (L)

27

Plate (R)

28

Base

P-1312

M8

T*1316

P-1057

T*1318

P-320

M8xP1.25x15

M10xP1.5x12(Blue Locktite)

NO.2737

M10xP1.5x35(Blue Locktite)

M8xP1.25x40

ψ5x25

NO.2392-L

NO.2392-R

29

Bolt

30

Nut

31

Post

32

Bolt

33

Deck

34

Nut

35

Spring

36

Spring Spacer

K-288

M10xP1.5

T*1026

M8xP1.25x35

NO.2393

M8xP1.25

S-077

P-1058

37

Safety key/ Clip

38

Cylinder CY-004

39

40

Water Bottle

Bolt

Tx771

M5xP0.8x10

P-1103L

41

Cover (L)

42

Cover (R)

43

Motor Bottom Cover

P-1103R

P-1314

PARTS LIST – CardioZone SuperSport™ Club

Qty Item

Description

1

2

2

1

1

4

1

1

2

2

1

2

1

1

1

60

Sensor (Round)

61

Bolt

62

Wire Button

63

Bolt

64

Bolt

65

Belly Pan

66

Bolt

67

Cushion

68

Bolt

69

Plastic

70

Bolt

71

Bolt

72

Washer

73

Bolt

74

Bolt

4

6

4

6

2

1

2

8

8

8

4

1

2

1

1

75

Rear Adjust Box (L)

76

Rear Adjust Box (R)

77

Bolt

78

Upper Cover

79

Front Roller

80

Running Belt

81

Side Rail

82

Rear Roller Set

83

Bolt

84

Sponge

85

Running Deck

86

Power Cord

87

Control Wire (Bottom)

88

Wire Button

89

Side Cover Plastic

90

Extention wire (Green)

1

4

5

1

1

91

Extention wire (White)

92

Extention wire (Black)

93

Extention wire (White)

94

Extention wire (Black)

1

15

1

95

Allen Wrench

96

Allen Wrench

97

Wheels

98

Bolt

1

1

2

1

99

Bolt

100

Foot Pad

101

Bolt

10 102

Metal Powder

1

1

1

103

Sensor plate

104

Metal Powder

105

Bolt (Steel)

M5xP0.8x12

UC-1

M4xP0.7x15

M8xP1.25x40

P-1388

M8xP1.25x50(25m

P-1301

M4xP0.7x10

P-1034

ψ4x12

M8xP1.25x55

ψ8xψ12x1.5t

M8xP1.25x45

M8xP1.25

P-1054L

P-1054R

M4xP0.7x20

P-1313

P-1053C

M8xP1.25x35

20x100x1.5t

UC-0

P-1319

14AWGx120mmx1T1R

14AWGx90mmx2T

14AWGx90mmx2T

14AWGx170mmx2T

14AWGx170mmx2T

6mm（80mmx80mm）

5mm（80mmx80mm）

P-1145

M4xP0.7x16

M8xP1.25x25

P-1151

ψ

4x20

T*1312

P-1152

T*1312A

M5xP0.8x8

Qty

8

1

2

3

4

2

4

8

1

1

2

1

1

1

1

2

6

1

2

1

2

1

2

1

1

1

1

1

2

1

6

2

6

8

8

32

2

1

1

4

2

1

3

3

1

2

20

TROUBLESHOOTING

ERROR MESSAGE

E1

- Loss of Feedback

- Running Deck

PROBABLE CAUSES SOLUTION

Speed Sensor disconnected

Running Deck not lubricated

Speed Sensor misaligned

Speed Sensor Faulty

Loose Display Cable

Check Speed

Sensor Connection

Check R-Deck oil

Check Sensor position

Replace S-Sensor

Check Display

Cable connection

(D2 LED on)

Drive Motor disconnected

Drive Motor Faulty

Check D-Motor connection

Replace D-Motor

E4

- Body Fat Data Incomplete Heart Rate not detected

- Loss of Data Faulty Receiver in Display

Faulty Control Board in

Display

Hold Heart Rate Grip Properly

Replace Heart Rate Receiver

Replace Heart Rate Control

Board

21

ERROR MESSAGE

E6

- Safety Key Off

- Elevation Motor

- Stalled Elevation

E7

- Elevation Motor

Display Doesn’t Lit Up

PROBABLE CAUSES SOLUTION

Safety Key Faulty Check Safety Key or Switch

Elevation Motor not moving

Elevation Motor screw binding Clean screw and lubricate

Check Elevation Motor connection

Elevation Motor out of Range Check Zero Position of

E-Motor

Elevation Motor out of Range Replace Elevation Motor

On/Off switch Check if unit is turned on

Insufficient Power Source

Line Cord Damaged

Fuse

Plug unit in a dedicated 120V,

20Amp Outlet

Replace Line Cord

Check Fuse on MCB

22

WARRANTY

USA Warranty

Warranties may vary in other countries.

Please register your warranty at http://www.fitnessblowout.com/warranty

SUPER GYM’S FITNESSBLOWOUT.COM extends the following exclusive, limited warranty of CARDIOZONE, which shall apply only to the use of the device in the home, for residential, non-commercial purposes only unless otherwise stated in writing. Any other use of the device shall void this warranty.

FRAME – LifeTime

Super Gym’s FitnessBlowout.com warrants the Frame against defects in workmanship and materials for Lifetime, so long as it remains in the possession of the original owner.

DRIVE MOTOR – LifeTime

Super Gym’s FitnessBlowout.com warrants the Drive Motor against defects in workmanship and materials for Lifetime from the date of original purchase, so long as the device remains in the possession of the original owner.

ELECTRONICS & PARTS – 2 Years

Super Gym’s FitnessBlowout.com warrants the Electronic components and all original parts (other than the Motor) against defects in workmanship and materials for a period of two years from the date of original purchase, so long as the device remains in the possession of the original owner.

LABOR – 1 Year

Super Gym’s FitnessBlowout.com shall cover the labor cost for the repair of the device for a period of one year from the date of original purchase, so long as the device remains in the possession of the original owner.

EXCLUSIVE REMEDY

The exclusive remedy for any of the above warranties shall be repair or replacement of defective parts, or the supply of labor to cure any defect, provided that labor shall be limited to one year. All labor shall be supplied by the local retailer and the product must be located within the retailer’s service area. Products located outside the retailer’s service area will not be covered by the labor warranty.

23

EXCLUSIONS AND LIMITATIONS

This warranty applies only to the original owner and is not transferable. This warranty is expressly limited to the repair or replacement of a defective Frame, Electronic component, or defective part and is the sole remedy of the warranty.

The warranty does not cover normal wear

Super Gym’s FitnessBlowout.com expressly disclaims all other warranties, express or implied, including but not limited to all warranties of fitness for a particular purpose or of merchantability. This warranty gives you specific legal rights and your rights may vary from state to state.

WARRANTY REGISTRATION

Register your warranty online at http://www.fitnessblowout.com

24