Extech Instruments S2500THS User guide

Extech Instruments S2500THS is a portable receipt printer capable of printing text, barcodes, and graphics on thermal receipt paper. It features multiple connectivity options including serial, IrDA, and Bluetooth, allowing for versatile use in various environments such as field service, sales, hospitality, and ticketing. Its compact size and belt loop system provide portability and convenience for on-the-go printing.

PDF

Document

Advertentie

S2500THS

USER

GUIDE

Getting Started:

Declaration of Conformity

General

1.1 Unpacking the printer

1.2 Installing and Charging the Battery

1.3 Reading the LED Status

1.4 Attaching Belt Loop System

Loading Supplies:

2.1 Adding Paper/Labels

2.2 Tearing

Using the Printer:

3.1 Initial power up and self-test

3.2 Connecting the Printer

3.3 Communications: Serial RS232C

3.4 Communications:

Bluetooth

3.6 Using the Magnetic Card Reader

3.7 Programming

Printer Maintenance

4.1 Cleaning

4.2 Charging the Printer Battery

4.3 Verifying Battery Charge State

4.4 Battery and Safety Information

4.5 Recycling your Batteries

Shooting

Supplies

Specifications:

5.1 Printer

Specifications

5.3 Regulatory

Declaration of Conformity

Name:

Manufacturer’s Address

Extech Instruments Corporation

285 Bear Hill Road, Waltham, MA 02451, USA

Telephone: +1 781 890 7440

Declares that the Product

Product Name: Portable Receipt Printer

Model Number: S2500THS;

S1500T

Optionally Containing: Bluetooth™ radio short range OEM module from connectBlue ab, cB-0701-01; FCC ID PVH 070101.

Conforms to R&TTE Directives: 1999/5/EC (EN 300 328-

2), EMC Directive 89/336/EEC (EN 301 489-1 and -17); and

Low Voltage Directive 73/23/EEC (EN 61131-2)

Conforms to the following regulation and/or standards:

FCC: Part 15 Subpart B, Class B

CE: EN55022 Class B;

CE: EN61000-3-2;

CE: EN61000-3-3 ;

CE: EN50024.

Supplementary Information : • The product complies with EMC Directive

89/336/EEC and Low Voltage Directive

73/23/EEC

• The product conforms to ANSI/UL STD 60950 &

Certified to CAN/CSA STD C22.2 No. 60950-00

• CB Certified

• ETL Listed, control # 3046813

• The product is IEC 68 certified

Signature: Antony Revis

Antony Revis, General Manager

General Precautions

• Before using this product be sure to read through this manual. After reading please keep the manual in a safe place for future reference.

• The information contained herein is subject to change without notice of any type.

• Extech is not responsible for any operational results regardless of missing information, errors or any misprinting in this manual.

• Extech is not responsible for problems created as a result of using options and consumables not approved by them.

• This product is designed for servicing at an Authorized Service Center. Other than routine maintenance described in this manual the user should not attempt to repair, service or disassemble this product.

• Incorrect operation, handling or improper operating environments may cause damage or otherwise affect the proper operation of this product. Such actions invalidate the product warranty.

Safety

In this manual and on the Printer and accessories we make use of internationally recognized safety symbols as follows:

Caution! Refer to the explanation in this Manual

Caution! Risk of electric shock

Double Insulation or Reinforced insulation

DC, Direct Current or Voltage

AC+DC, Current or Voltage

Note: One battery cartridge is included with the printer. Similar to a cordless phone battery, the printer’s battery must be charged before using it.

1. Getting Started

1.1 Unpacking the Printer:

The S2500THS and S1500T portable printers are full featured portable receipt printers designed for varied job environments including field service, field sales, hospitality and restaurants, ticketing and many others where point of service receipts are required. The package contains:

printer:

battery cartridge,

AC wall mounted charger (may be USA, European or UK style plug), for charging the battery inside the printer

1 .

belt loop system and

roll of paper supply (already loaded in the printer).

Both cabled and wireless communication is possible.

1.2 Installing and Charging the Battery Cartridge:

1 :

: I n s t a l l l l i i n g t h e b a t t e r y

Note: Refer to the illustration below to install the battery pack in the printer.

Extech batteries must be cycled several times to achieve maximum capacity. To cycle a battery fully charge it and then allow full discharge through normal use in the printer.

Unlock the battery door by sliding the battery door locking tab down

Open the battery door

Insert the battery as shown. The battery side with two contact terminals should be facing down to make contact with the two spring probes inside the battery compartment.

Close the battery door.

Lock the battery door by sliding the battery door locking tab up

B a t t

I n o s t t t t t o t e r a l l m r y l e d o

C f o t h m e p a

P r r r t i i n m t t e e r n t

S h t h w i i o t w h i i n

B g a t t t t e r r y

1 .

2 .

2 C h a r g i i n g t h e B a t t e r y

 Charge the battery by inserting the wall mounted charger line cord into the printer jack (Refer to Figure 4 on page (20) for the location of the adaptor

jack on the printer). Then insert the charger plug into an appropriate wall socket.

The Yellow/Amber charging LED will illuminate indicating that the battery is being charged

The battery will be fast charged and after about 180 minutes the LED will go off

To remove the battery cartridge, open the battery door and tip the battery out of the printer .

Note: To ensure a full charge do not operate the printer while charging.

Note: The wall mounted charger is a Class II equipment ( ) . Multiple plug configurations comply with most international standards.

S2500T

Input Voltage/Current 100-240 VAC/0.5A

Input Frequency 47-63 Hz

Output Voltage/Current

( )

10VDC/1A

Note: The wall mounted charger is not supplied with plugs for use in Korea.

Do not use a charger not approved by Extech for use with the

S2500THS. Use of an unapproved charger could damage the battery pack or the printer and will void the warranty.

The battery terminals are well recessed inside the printer. Do not allow them to contact conductive material since this may create a short circuit which could cause injury or start a fire.

When using the wall mounted charger ensure the socket outlet is close to the printer and easily accessible during the battery recharging process. Either switch the socket off (if supplied with a socket switch) or pull out the charger from the socket or disconnect the plug from the printer in the event of any problems.

1.3 Reading the LED Status:

This table explains the LED indicator status. Refer to Figure 4 for the locations described for ON/OFF and FEED pushbutton switches and AC adaptor socket .

LED Indicator State Status

Multi Function: ON Green --- Printer is on and

Dual Green & Yellow or Red ready to receive data.

Yellow --- Indicates low power.

Battery needs recharge.

 Red --- Very low power. Printing not possible.

 Yellow --- The battery charger is charging the battery at a fast rate. If the battery is below

5.0V, the battery is being

“trickle” charged until the battery voltage reaches 5.0V, and then the fast charge rate is started. The LED will turn Off when the battery is fully

charged.

Green and Red ON Green --- Indicates that MCR is ready to accept data.

 Red --- Indicates a fault condition or a printer error. The printer is not ready to accept data.

Note: Refer to the troubleshooting guide to determine error or fault condition.

Table 1 - Reading the LED Status

1.4 Attaching Belt Loop System:

The belt loop system consists of two parts:

A knob located on the back part of the printer just above the battery door

A strap with click on connector

To attach the strap insert the knob located at the bottom of the printer into the slot of the connector. Pull down until you hear a click. The printer is now secure. Place the loop over your belt. Allow the printer to hang down on the left or right hip.

To release the printer, press in on the two latches on the connector and pull the knob clear of the slot.

Note: Do not force or pull the printer from the connector without pressing in on the two latches

2. Loading Supplies

2.1 Adding Paper/Labels:

The printer can print text, bar codes and graphics on thermal receipt paper. See

“Supply Specifications” for the width, thickness requirements and approved vendors. Follow these steps to load printer paper.

Press down on the button on the top cover (next to the Extech label) as shown in Figure 4 .

The paper door will pop open a short way.

Grip either side of the paper door and open – it will open to 180 degrees.

Place the paper roll into the paper supply well. Make sure the paper supply unwinds from the bottom as indicated below with the thermal side closest to the print head.

Unroll about 3 inches of paper from the roll and position between the print head guides.

Close the paper door.

L o a d i i n g t t h e P a p e r r R o l l l l

2.2 Tearing Paper:

The printer’s paper door acts as a tear bar. Pull one edge of the paper against the tear bar as indicated, then tear down and across against the tear bar to tear the paper.

Caution: The tear bar may have sharp edges.

Using the tear bar is the only way to tear the paper.

Pulling up and pulling sideways without using the tear bar can cause a paper jam due to paper misalignment in the printhead mechanism.

T e a r i n g t t h e P a p e r

3. Using the Printer

3.1 Initial power up and self-test

Once the Battery is charged and the paper is loaded an initial power up self-test can be performed.

Press the <On/Off> switch once. This turns printer on. The Green LED illuminates

After approximately 20 seconds, if no instructions are sent to the printer, the printer will automatically turn off to conserve battery

life.

If the printer is set for infrared communications (IrDA) mode the printer will stay on all the time. Pressing the <On/Off> switch again will turn the printer off.

Press the <On/Off> switch to turn the printer off. The green LED turns off.

To start the self-test, press and hold the <FEED> switch then press the

<On/Off> switch

The printer will start printing the self-test messages. Release the <FEED> switch.

Press the <On/Off> or <FEED> switch to stop or cancel the self-

test print.

The first few lines of self-test show the printer firmware version, the current printer settings (for example IrDA or Serial mode) and a list of any optional or special features installed.

3.2 Connecting the Printer

The 2500THS printers support Serial RS232 and IrDA compatible infrared communication interfaces. Radio frequency (RF) communication is also available as an optional feature.

Serial, IrDA and Bluetooth communication settings can be changed via a DIP switch located on the control card.

The DIP switch is located inside the battery compartment as illustrated below indicating the location of this switch. Figure 1A shows the DIP switch selection.

The functions assigned to these switches are shown TABLE 2 .

If the Serial interface is selected, the communication Parameters, Baud rate,

Data Bit and Parity, must be set.

Note: Optional serial cable is available for Serial RS232 communication (part # 5892RJD9).

Printer drivers for Windows 95/98/NT/2000 and XP are available from

Extech.

PrinterCE print Control utility is available from Extech for Windows CE devices.

Printboy Print Utility from Bachmann Software or PalmPrint Utility, from

StevensCreek, are recommended for Palm Pilot devices

3 .

2 .

1 L o c a t i i o n o f f D i i p S w i i t c h e s

Infrared Communications

(IrDA):

Dip switch #1 must be in the <On> position.

Serial and Bluetooth

Communications:

Dip Switch #1 must be in the <Off> position.

3 .

2 .

2 S e t t i i n g D i i p S w i i t c h e s

3 .

2 .

3 D i i r D A )

Note: Be careful when changing dip switch settings. Carefully use a pointer on the dip switch you are going to change. DO NOT use a screw driver or apply excessive force. p

S i i g w i i u t c r e h F

1 u

A n

: c

D i t t i i i p o n s

S w i i t c h S e t t i i n g s ( S h o w i i n g s e t t i i n g f o r I r

Developer’s refer to Programming Manual for more information

In order for changes to the dip switch configuration to take effect, the printer power must be reset.

Dip Switch

2 & 3

Function

Communication Interface

Baud Rate

Switch #

SW1

Switch #

Off

SW2 SW3

2,400

4 Printer Power Control (Software)

Continuous Power On (can be shut down by pressing On/Off switch)

SW4

6 & 7

Auto Power Off Off

Optional SW5

Parity bit SW6 SW7

8 Printer Power Control (Hardware)

Continuous Power On (can be shut down only by taking the battery out)

Auto Power Off

SW8

Off

Table 2 – DIP Switch Setting

3.3 Communications: Serial

The RS232C Interface signals for the 2500THS Series printers are terminated on a 6 PIN RJ type data connector located on the side of the printer.

Six connections are provided from the Serial Interface to the host computer.

TABLE 3 below lists the Serial Interface signals and pin outs on the RJ connector and the connector pin locations are shown in FIGURE 3 .

A minimum two connections are required for operation, RXD – pin 3 and

Common – pin 1.

Note: The communication Parameters: Baud rate, Data Bit and Parity must be set the same as the host device settings. Dip switch #1 must be in the OFF position.

FIGURE 3 – R J D A T A C O N N E C T O R

TABLE 3 - 2 5 0 0 T H S S e r i i a l l R S 2 3 2 C I I n t t e r f f a c e s i i g n a l l s

3.4 Infrared Communications (IrDA):

Dip Switch #1 must be in the <ON> position

The printer can be powered up by pressing the power <On/Off> switch

If no IrDA connection is made, the printer will automatically power down to a lower power level to conserve battery life. It will remain in a “sleep” mode until an IrDA connection is made, at which time the printer will “wake” up and print the requested data

Pressing the power switch again will turn the printer <OFF>.

3.5 Bluetooth Communications (Option):

All Dip Switches must be in the <OFF> position

Note: Adjust settings to match those of the Bluetooth module in your computing device

The printer can be powered up by pressing the power <On/Off> switch

When powered up in Bluetooth mode, the printer will not enter a “sleep” mode and will remain active waiting for the wireless print command

Pressing the power <On/Off> switch again will turn the printer <OFF>.

Note: In Bluetooth mode it is necessary for the mobile computing device you are using to discover the printer and the printer needs to be set as a favorite. Refer to instructions provided by the systems integrator.

Note: Systems Integrators: Refer to the Bluetooth manual provided with your mobile computer and the Bluetooth section of the Developer’s

Manual available for this printer.

3.6 Using the Magnetic Stripe Reader:

The Magnetic Card Reader is a factory-installed option. This option requires special application software to read and process cards with a magnetic stripe, such as credit cards or driver’s license

Note: Refer to the Figure 4 if your printer is equipped with the optional magnetic stripe reader

Quickly swipe the card through the reader either left to right or right to left.

The magnetic stripe must be facing toward the paper supply door as indicated below while it is passed through the reader

Refer to Table 4 for the description of the LED indicator Status.

LED indicator

Green

State

Status

Ready/waiting for card to be swiped.

Red

OFF

Good swipe - Card data read OR

Card not ready to be swiped.

Error reading card’s data.

T a b l l e 4 M a g n e t i i c C a r d L E D I n d i c a t o r

M a g n e t t i i c C a r d S w i i p e I l l l u s t t r r a t i o n

3.7 Programming Information:

This section lists the printer control commands strings.

Note: System Developers: Please refer to S2500T programmer’s manual for further details.

Other features may be available and are described in the programmer’s manual

3.7.1 ASCII CONTROL CHARACTERS:

Character Hex/Dec

EOT 04/04

08/08

09/09

0A/10

0B/11

0C/12

0D/13

0E/14

XON

AUXON

XOFF

NORM

AUXOFF

CANCEL

0F/15

11/17

12/18

13/19

14/20

15/21

18/24

CONTROL ACTION

End Of Text

Back Space

Horizontal Tab

Line Feed

Vertical Tab

Form Feed

Carriage Return

Shift Out

Shift In

Transmitter On.

Printer on.

Printer receiver is off

Return to default 42 column mode

Printer to Host: printer is off

Cancel and reset printer BUFFER

EXTEND 1C/28

EXTEND OFF 1D/29

Extended print

Extended print off/Normal print

3.7.2 Printer Font Commands – Courier Character Set:

Font Name

24 CPI normal

21 CPI normal

19 CPI normal

Character size (W x H) Command String

8x23 ESC+'k'+'5'

9x23

10x23

ESC+'k'+'4'

ESC+'k'+'3'

16 CPI normal

12 CPI normal

13 CPI rotated

12x23

16x23

14x16

3.7.3 Printer Font Commands :

ESC+'k'+'2'

ESC+'k'+'1'

ESC+'k'+'0'

Command String

ESC - ‘F’ – 1

ESC - ‘F’ – 2

ESC - ‘U’ - ‘1’

ESC - ‘U’ - ‘0’

Printer Action

Selects International character set

Selects PC Line Draw character set

Enable emphasized print.

Disable emphasized print.

3.7.4 Printer Graphic Commands:

Command String Printer Action

ESC - ‘a’ – n

ESC - ‘J’ – n

ESC - ‘P’ - ‘#’

ESC - ‘P’ - ‘$’

ESC - ‘V’ - n1 – n2

ESC - ‘v’ - n1 – n2

Select dot line spacing between printed lines.

Graphic Line Feed command

Select Online mode, characters printed as received.

Select Buffer mode, characters are printed on (^ D)

8-bit Graphic command

RLE Compressed Graphic command

3.7.5 Magnetic Card Reader Control Commands:

Command String Printer Action

ESC - ‘M’ - ‘nnm’ - Cr

ESC – ‘C’

Select MCR with (nn) auto timeout

Cancel MCR read process

3.7.6 Graphic Logo and Bar code commands:

Command String Printer Action

ESC – L – G –n

ESC – G - 0x0FF

ESC – L – g – n

ESC - 'z' - n1 – n2 - L - [data]

ESC - 'Z' - n1 – n2 - L - [data]

ESC - ‘Q’ - ‘J’ – n

ESC - ‘Q’ - ‘Q’ – n

ESC - ‘Q’ - ‘F’ – m

ESC - ‘Q’ - ‘B’ – m

Prepare printer to load image:

Loading Logo Complete:

Print stored logo image:

Print Bar Code without visible text

Print Bar Code with visible text

Reverse Dot Feed

Set Out of Paper Sensitivity

Set Forward Black Mark Seek

Reverse Black Mark Seek

3.7.7 Printer Supervisory and Control Commands:

Command String Printer Action

^V Buffer, power timer & battery status

ESC - ‘P’ –‘^’

ESC – ‘P’ – alpha

ESC – ‘M’ - ‘000’ - Cr

ESC - ‘M’ - ‘nn0’ - Cr

ESC – ‘M’ - ‘C’

ESC – ‘P’ – ‘( ‘

ESC – ‘ P’ - ‘)’

Print Battery Voltage

Time and date print and control disable the power down timer sets the power down timer to nn seconds

Reset Auto power down to 20 seconds

Firmware version query

Hardware model query:

4. Printer Maintenance

4.1 Cleaning:

You may need to clean the print head and platen roller after printing a number of rolls of paper, whenever you load new supplies or when you see voids in the printout.

Caution: Do not use sharp objects to clean the print head. This may damage the printer and require service.

Open the paper door by pressing the button on the top cover (next to the

Extech label) as shown in Figure 4. The paper supply door will pop up.

Remove the paper roll.

Moisten a cotton swab with isopropyl alcohol and clean the print head

Clean the platen roller with a dry cloth or small brush

Note: You can also use another cotton swab moistened with isopropyl alcohol. Turn the platen roller with your finger and run the cotton swab or

dry cloth across it. Make sure the platen roller is clean all the way around.

Moisten another cotton swab with isopropyl alcohol. Rub the swab across the black mark sensor to remove any build-up

Moisten another cotton swab and rub the swab across the tear bar to remove any build-up

Note: You may experience dust build-up depending on the environment and the quality of the paper supply you use. If this occurs, use a can of

compressed air to blow dust and paper debris out of the printer.

4.2 Charging the Printer Battery:

The printer battery is charged using the wall mount adapter provided. Follow these steps to charge the battery pack.

Plug the power adapter into an appropriate wall socket; then plug the power adapter cord into Adapter Plug on the side of the printer (see Figure 4 )

The yellow CHARGE LED will illuminate, to indicate battery is charging

The Charge LED turns off when battery cartridge is fully charged. It takes about 180 minutes to fast charge the battery cartridge

To insure full charge, printer should not be operated while the battery is

4 .

2 .

1 I charging. m p o r r t a n t N o t e s o n C h a r r g i i n g B a t t t e r r i i e s

4 .

2 .

2 I

The model 2500THS printers require an adaptor output of 10VDC/1.4A.

The battery Fast-charge is initiated each time the power adapter is connected to the printer

The fast-charge controller checks the battery’s voltage and temperature, before the start of the fast recharge process. If the battery voltage or the temperature is outside of the fast-charge limits, the charger defaults to trickle charge at C/10 or 70mA rate

Optional external battery chargers are available for Extech batteries m p o r r t a n t N o t e s o n R e p l l a c i i n g B a t t e r i i e s

Check for the correct Extech part number for the battery and only order that part for your new battery

Caution: Risk of explosion if battery is replaced by an incorrect type.

Caution: Dispose of used batteries according to instructions in Section

4.5

4.3 Verifying Battery Charge State:

It is strongly recommended testing your printer before returning to Extech. Follow these steps to identify and correct any battery power problem that may be encountered. These will help to identify that the fault is with the printer and not some other part of your system.

To test the AC adaptor use a multi-meter and measure the output. Output should be 10VDC

Press the <ON/OFF> switch and wait until all LED’s are off

Insert the AC adaptor plug into the printer. If the amber LED goes on, the battery is not fully charged but the charge circuit is functioning.

The AC power portion of the circuit appears ok

Disconnect the AC Adapter once the battery has charged for 5 minutes or so.

Press and hold the <FEED> switch, then press and release the <ON/OFF> switch and then release the <FEED> switch. The printer will print a “self test” receipt

If the self test receipt is printed, the DC power is ok

Press <ON/OFF> switch and wait until all LED’s are off

Plug the AC adaptor into the printer. Press <ON>; the green LED is illuminated and after about 20 seconds the LED should go off

If the amber LED is on, this will continue on through this test indicating that the battery is accepting a charge and that the charge circuit is ok. At the end of a 180 minute charge cycle the LED will go off.

4.4 Battery and Safety Information:

The printer is powered by a 7.4V Li-Ion battery cartridge.

Charging time in the printer is approximately 3.0 hours

Take the battery out of printer if storing the printer for long periods of time

The battery storage temperature is 40°F to 104°F (4°C to 40°C). Do not store a fully charged battery at temperatures greater than 104°F (40°C) for long periods of time – the battery may permanently lose charge capacity

Be sure to use a fully charged battery before long or battery intensive printing sessions. Certain operations (for example, printing receipts with a lot of bar codes and graphics) drain the battery more quickly than others

Dispose according to your local regulations. Do not throw in trash

Caution: Do not disassemble, short circuit, heat above 80°C, or

incinerate. The battery may explode

The recommended temperature for charging is between 68°F (20°C) to 77°F

(25°C).

4.5 Recycling your Batteries:

The Rechargeable Battery Recycling Corporation (RBRC) is a non-profit organization created to promote recycling of rechargeable batteries. For more information about how to recycle batteries in your area, visit www.rbrc.org.

4.6 Trouble Shooting:

Problem

Does not feed paper or has a paper jam.

Does not print

Action

Remove any jammed supply

Reload paper supply.

Check or replace the printer’s battery

Make sure the paper supply is loaded correctly, not backwards.

Verify communication between the host device and the printer by disconnecting the communication cable and performing

Light printing

Voids in printing

Red (Error) LED on a printer self test.

Check or recharge the battery

Adjust the print contrast through print application.

Clean the print head following the cleaning

instruction listed in Cleaning section.

Check that paper roll is not out

Error reading MCR

After extended printing, print head may be hot; printer will pause before resuming printing.

If the problem is not identified following above trouble shooting guide, contact Extech

Technical Support.

Support numbers and Email addresses are listed at www.extech.com

Other than routine cleaning and other maintenance described in Section 4, the printer is not intended to be serviced by the user. It must be returned to an authorized service center .

Under no circumstances should the user attempt to take the printer apart.

4.7 Printer Supplies:

78328I1

78328I1R

757060

7A1000011

157120

157220

157240

Part Number

S2500THS-UG-2A.doc

7A060028

Available from Extech Email: [email protected]

Download: http://www.fieldsoftware.com/PrinterCE.htm

Download http://www.stevenscreek.com/pilot/dodownload.htm

http://www.bachmannsoftware.com/downloads.htm

5892RJD9

Description

S2500THS PKG 120v (US Plug)

S2500THS MCR PKG 120v (US Plug)

2500THS Thermal paper pack (2.25”/57 mm, 5 rolls per pack)

2500THS Li-Ion Battery Cartridge:

7.4VDC– 1800mA

Battery charger adapter 2500THS

Input 120VAC/Output 10VDC @ 1.4A (US Plug)

Battery charger adapter 2500THS

Input 220VAC/ Output 10VDC @ 1.4A (Euro Plug)

Battery charger adapter 2500THS

Input 240VAC/ Output 10VDC @ 1.4A (UK Plug)

User’s Guide - 2500THS

Programmer’s Guide - 2500THS

Windows 95/98/NT/2000/ Drivers

Windows CE print Utility

Palm Pilot print Utility

PrintBoy for Palm O/S

Serial Data Cable – RJ to DB9 PC compatible

TABLE A - Printer parts and supplies

5 Specifications

5.1 Printer Specifications:

Height:

Length:

Weight: w/battery & supply

Shipping weight:

Power:

Operating Temp. Limits:

Storage Temp. Limits:

Operating Humidity Limits:

Storage Humidity Limits:

Print head:

Printing Method:

Print Speed:

Supported Fonts:

(Bitmap)

Supported Bar Codes:

Memory:

Charging Time:

Communications:

Print Ratio:

5.2 Supply Specifications:

Supplies:

Supply Thickness:

Supply Width:

Supply Length:

Supply Sensing:

Paper roll diameter:

Maximum Print Area:

Approved Vendors:

2.56 inches (64mm)

5.3 inches (135mm)

1.2 lbs. (0.55 g)

2.8 lbs. (1.31 kg)

7.4 V Li-Ion battery

41F to 104F (5 to 40C)

-4F to 140F (-20C to 60C)

20% to 85% non-condensing

5% to 95% non-condensing

2.25” wide (57mm); 203 dpi (8 dots per mm)

Thermal Direct

Up to 2.0 inches per second

Standard (normal and bold)

Large (normal)

Reduced (normal and bold)

Large rotated.

Codabar, Code 39, UCC/EAN – 128, UPC/EAN/JAN,

Interleaved 2 of 5, Code 128

32K SRAM, 128K Flash

Approximately 180 minutes

RS-232 port; IrDA; Bluetooth option

25% black maximum/sq.in.

Thermal direct receipt paper

2.2 to 3.5 mils (receipt paper)

2.25 inches (58mm)

1 roll of receipt paper is approx. 600 inches (15,240 mm)

Black mark (on face of supply)

Outside: 1.5 inches (37.5 mm)

Inside: .56 inches (14 mm)

1.85 inches (72 mm) X 5.3 inches (203mm)

Kansaki: P300, P310, P350, P354, P530UV, TO281CA,

OP200, TO381N, F180, F380, F550

Jujo: TF-50KS-E2C

Honshu: FH65BV-3

FIGURE 4 – 2500THS Features

1. Power (Green)/Low Power

(Yellow) dual LED indicator

2. Charge(Yellow) LED indicator

3. MCR(Green)/Fault(Red) dual

LED indicator

4. Paper Door Release Button

5. ON/OFF Button

6. Paper Feed Button

7. MCR Swipe

8. AC Adapter Plug

9. RJ (Serial Interface) plug

10. IrDA Interface

5.3 Regulatory Notes:

5 .

3 .

1 F C C P a r r t t 1 5 C l l a s s B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to

For Bluetooth equipped printers please note: which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

5 .

3 .

2 W

The printer contains an OEM Serial Port Adapter from connectBlue with FCC

ID: PVH070101. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” t y : W a r r r a n t

This printer is warranted by Extech Data Systems to be free of defects in parts and workmanship for a period of one year from date of shipment. This warranty does not apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification.

Extech specifically disclaims any implied warranties of merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, special, incidental or consequential damages. Extech’s total liability is limited to the repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral is expressed or implied.

5 .

3 .

3 W a r r a n t y a a n d / o r R e p a i i r S e r v i i c e :

A Return Authorization number must be issued before a unit is returned to Extech for repair.

Once a unit has been properly returned to Extech (Note: The customer is responsible for ensuring proper packing to prevent damage in transit as well as the shipping costs back to

Extech), it will be repaired (estimates are provided first if the repair cost is estimated above

$100.00) and returned via UPS ground. The customer may elect a faster mode of transport at their cost.

Hallo! Ik ben een AI-chatbot die specifiek is getraind om u te helpen met de Extech Instruments S2500THS User guide. Ik heb het document grondig doorgenomen en kan u helpen de exacte informatie te vinden die u nodig heeft of de inhoud in duidelijke en eenvoudige bewoordingen uit te leggen. Of u nu op zoek bent naar begeleiding bij specifieke functies, stappen voor probleemoplossing of algemeen gebruik, stel gerust uw vragen. Hoe meer details u verstrekt over uw zorgen of behoeften, hoe nauwkeuriger en effectiever ik u kan helpen!

Assistent aan het typen

Assistent is niet meer aan het toetsenbord. Probeer het later opnieuw.

Het lijkt erop dat u een document hebt bereikt dat in meerdere talen is geschreven, waaronder een die niet uw moedertaal is. U kunt de volgende links gebruiken om tijdelijk pagina''s te verbergen zonder de taal van uw voorkeur.