TV C

HANNEL

I

NSTALLATION

Immediately after unpacking and plugging in your new television, run the auto program function to set up the TV for the broadcast or cable channels available in your area. If you do not run the auto program function to set up the channels , your television may not operate properly.

Please follow these steps to install TV channels:

1

2

3

Select a TV channel via SOURCE button on your remote control.

Press MENU button on your remote control to open the onscreen menu.

Press CH(-) to move to INSTALL,press VOL(+) on your remote control to enter

INSTALL.

4 Press CH(-) to select TUNER MODE, press VOL(+) on your remote control to select CABLE, ANTENNA or AUTO mode.

CABLE IF you have a cable input

ANTENNA IF you have an antenna input

AUTO IF you are not sure what kind of TV signal input you have

(Cable or Antenna)

5

6

Press CH(-) to move to AUTO PROGRAM.

Press VOL(+) to start auto install the TV Channels.

For more detailed explanation of AUTO PROGRAM, please refer to

AUTO PROGRAM section on page 5.

M E N U

SOURCE

C C

OK

P I P

MAIN CONTROLS

PICTURE

AUDIO

FEATURES

INSTALL

LANGUAGE

TUNER MODE

AUTO PROGRAM

CHANNEL EDIT

MANUAL FINE TUNE

FACTORY RESET

INSTALL

LANGUAGE

TUNER MODE

AUTO PROGRAM

CHANNEL EDIT

MANUAL FINE TUNE

FACTORY RESET cable

INSTALL

LANGUAGE

TUNER MODE

AUTO PROGRAM

CHANNEL EDIT

MANUAL FINE TUNE

FACTORY RESET

AUTO STORE

PLEASE WAIT

PROG.FOUND

CHANNEL

START?

0

3

U

NFOLD THE

B

ASE

Expanding the base requires a degree of force; please use sufficient force to unfold the base.

When unfolding the base, place the TV on a flat, sturdy surface before expanding the base.

1

1

2 3

3138 155 23293

Quick Use and Hookup Guide

C

ONTENTS

TV C

HANNEL

I

NSTALLATION

. . . . . . . . 1

U

NFOLD THE

B

ASE

. . . . . . . . . . . . . . . 1

I

NSTALLING

LCD TV

ON

T

HE

W

ALL

. . 2

P

RESENTATION OF THE

LCD TV . . . . . 2

A

CCESSORIES

. . . . . . . . . . . . . . . . . . . . 3

B

ATTERY

I

NSTALLATION

. . . . . . . . . . . . 3

R

EMOTE

C

ONTROL

O

PERATION

. . . . . . 3

A

NTENNA

TV . . . . . . . . . . . . . . . . . . 4

B

ASIC

C

ABLE

TV C

ONNECTION

. . . . . 4

T

UNER

M

ODE

C

ONTROL

. . . . . . . . . . . . . 5

A

UTO

P

ROGRAM

(S

ETTING

U

P

C

HANNELS

) . . . . . . . . . . . . . . . . . . . . 5

C

ABLE

B

OX

(

WITH

RF I

N

/O

UTPUTS

) . . 6

C

ABLE

B

OX

(

WITH

A

UDIO

/V

IDEO

O

UTPUTS

) . . . . . . . . . . . . . . . . . . . . . 6

S-V

IDEO

C

ONNECTIONS

. . . . . . . . . . . 7

C

OMPONENT

(HD) C

ONNECTIONS

. . . 7

PC (M

ONITOR

) I

NPUTS

. . . . . . . . . . . 8

IMPORTANT

NOTE: This quick setup guide is used with several different LCD TV models. Not all features (and drawings) discussed in this manual will necessarily match those found with your LCD TV set. This is normal and does not require that you contact your dealer or request service.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD

DO NOT EXPOSE THIS UNIT TO RAIN OR EXCESSIVE.

1

2

3

I

NSTALLING

LCD TV

ON

T

HE

W

ALL

The stand of your LCD TV complies with the VESA standard, if you intend to install the LCD TV on the wall, please consult a professional technician for proper installing.

Wall Mounting of your LCD TV :

Fold the base backward

Use for the TV set a Vesa compliant wall mount (not included).

(For 15 inch: 75x75 mm , For 20 inch: 100x100 mm)

Use for installation a professional technician.

Note: The manufacture accepts no liability, ensure installation is done by a professional technician.

(For 15 inch: 75x75 mm , For 20 inch: 100x100 mm)

1

2

3

4

P

RESENTATION OF THE

LCD TV

Television Keys

• VOLUME + / - : To adjust sound level.

• CHANNEL + / - : To select programs.

• MENU : To access or close onscreen menu,

� -

������

+

���� �������������������

�

Power button, LED light and infrared sensor

• : To switch the TV on or off.

• Aim remote control at infrared sensors to activate

TV controls.

Rear connectors

Remove the cable cover to access the connectors at the rear of the LCD TV.

Bottom connectors

Located at the bottom of the set.

�

2

S - VIDEO

AUDIO

VIDEO

Side Jack Panel of Television

�

Power adapter & cable Owner`s Manual & Quick Use and Hookup Guide

Power adapter & cable

A

CCESSORIES

When you unpack this unit, make sure it includes the following:

Wa rran ty C ard

Owner`s Manual & Quick Use and Hookup Guide

B

ATTERY

I

NSTALLATION

1

2

3

Remove the battery compartment lid on the back of the remote.

Place two AAA batteries in the remote. Be sure the (+) and (-) ends of the batteries line up as marked inside the battery compartment.

Wa rran ty C ard

Reattach the battery compartment lid.

Warranty Card

�

Tuner L-Adapter Warranty Card

�

�

R

EMOTE

C

ONTROL

O

PERATION

Number buttons

Press to select TV channels. When selecting single-digit channels, press the number of the desired channel.

The LCD TV will pause for a few seconds then tune to the selected channel.

Mute button

Press to eliminate or restore the LCD TV sound. Mute will appear on the screen when the sound is muted.

Menu button

Press to activate onscreen menu, back to previous level inside the onscreen menu, also press to exit the onscreen menu.

Volume button

Press to increase or decrease the sound level, also press to navigate left/right in onscreen menu.

Source button

Press to select the video input source: AV,

S-Video, HD, PC, TV.

OK button

Press to confirm the option you selected in the onscreen menu.

C.C button

Press the C.C button to select CC on or CC off.

M E N U

SOURCE

C C

OK

P I P

Standby (Power) button

Press to turn the LCD TV on or off.

Sleep button

Press to set the LCD TV to turn itself off within a certain time.

Smart Picture button

Press repeatedly to select either Personal, Movie,

Sports, Weak signal, or Multimedia picture setting.

Smart Sound button

Press repeatedly to select among the 4 settings;

Personal, News, Music, or Theater.

Picture Format button

Press the FORMAT button repeatedly to toggle among the four screen format sizes; 4:3, EXPAND

4:3, COMPRESS 16:9, or HD 4:3.

Previous Channel button

Press to go to previously selected channel.

PIP button

Press repeatedly to change the size of PIP window in PC mode.

Channel button

Press to adjust the channel up or down. Also press to select or navigate up/down in onscreen menu.

SAP button

Press to select a sound mode if available with the

TV programming:Mono, Stereo, or SAP.

3

A

NTENNA

TV

3

4

2

A combination antenna receives normal broadcast channels (VHF 2–13 and UHF 14–69). Your connection is easy because there is only one 75 Ω (ohm) antenna jack on the side of your TV, and that’s where the antenna goes.

1

If your antenna has a round cable (75 ohm) on the end, then you’re ready to connect it to the LCD TV. If your antenna has flat, twin-lead wire (300 ohm), you first need to attach the antenna wires to the screws on a 300- to 75-ohm adapter(not supplied).

Outdoor or Indoor Antenna

(Combination VHF/UHF)

3

Connect the antenna (or adapter) to one end of the supplied L-Adapter as shown, and connect the other end of the L-Adapter to the TV jack on the side of the LCD TV.

DC Adapter

Plug the DC adapter into the DC IN 16V jack on the LCD

TV. Plug the power cable into an outlet and switch TV set on.

Power

Cable

Rear Jack panel of

Television

2

Run the AUTO PROGRAM function to set up the TV for the broadcast or cable channels available in your area. If you do not run the auto program function to set up the channels , your television may not operate properly.

Twin-lead wire to

300-75 Ω adapter

1

OR

H

ELPFUL

H

INT

• Remember, an antenna or cable TV signal must first be connected to

your LCD TV.

• Please make sure that you have selected the TV mode with source key

on your remote control, before installing TV channels.

Antenna with 75 Ω cable

B

ASIC

C

ABLE

TV C

ONNECTION

Your Cable TV input into your home may be a single (75 ohm) cable or use a cable box decoder. In either case the connection is very simple. Follow the steps below to connect your cable signal to your new television.

2

3

Direct cable connections:

1 Connect the Cable TV signal to one end of the supplied

L-Adapter as shown, and connect the other end of the adapter to the TV jack on the LCD TV.

Plug the DC adapter into the DC IN 16V jack on the LCD

TV. Plug the power cable into an outlet and switch TV set on.

Run the AUTO PROGRAM function to set up the TV for the broadcast or cable channels available in your area. If you do not run the auto program function to set up the channels , your television may not operate properly.

2

DC Adapter

Power

Cable

Rear Jack panel of

Television

The Cable TV signal from

Cable Company

(75 Ω coaxial cable)

1

L Adapter

H

ELPFUL

H

INT

• Remember, an antenna or cable TV signal must first be connected to

your LCD TV.

• Please make sure that you have selected the TV mode with source key

on your remote control, before installing TV channels.

4

T

UNER

M

ODE

C

ONTROL

The Tuner Mode allows you to change the LCD TV’s signal input to Cable or Air

(antenna). It’s important for the LCD TV to know if you want to receive channels from a cable TV signal or an antenna signal.

3

4

5

1

2

Press the (CH-) button to highlight the INSTALL menu.

Press the (VOL+) button to enter the INSTALL menu.

Press the (CH-) button to highlight the TUNER MODE menu.

Press the (VOL+) or (VOL-) buttons to select CABLE, ANTENNA or AUTO.

6

H

ELPFUL

H

INT

• When CABLE is selected, channels 1-125 are available.

• When ANTENNA is selected, channels 2-69 are available.

• When AUTO is selected, your LCD TV will search automatically for antenna

or cable channels.

• Immediately after unpacking and plugging in your new television, run the AUTO

PROGRAM function to set up the TV for the broadcast or cable channels

available in your area. If you do not run the auto program function to set up the

channels, your television may not operate properly.

�

�

�

�

MAIN CONTROLS

PICTURE

AUDIO

FEATURES

INSTALL

M E N U

SOURCE

C C

OK

LANGUAGE

TUNER MODE

AUTO PROGRAM

CHANNEL EDIT

MANUAL FINE TUNE

FACTORY RESET

P I P

�

�

INSTALL

LANGUAGE

TUNER MODE

AUTO PROGRAM

CHANNEL EDIT

MANUAL FINE TUNE

FACTORY RESET

CABLE

A

UTO

P

ROGRAM

(S

ETTING

U

P

C

HANNELS

)

Your LCD TV can automatically set itself for local area (or cable TV) channels. This makes it easy for you to select only the TV stations in your area by pressing the CH (+) or CH (-) button.

3

4

5

6

1

2 onscreen menu.

Press the (CH-) button to highlight the INSTALL menu.

Press the (VOL+) button to enter the INSTALL menu.

Press the (CH-) button to highlight the AUTO PROGRAM control.

Press the (VOL+) button to start the AUTO PROGRAM scanning of channels.

Press the MENU button repeatedly to clear the menu from the screen, after AUTO STORE has finished.

M E N U

SOURCE

C C

OK

P I P

MAIN CONTROLS

PICTURE

AUDIO

FEATURES

INSTALL

INSTALL

LANGUAGE

TUNER MODE

AUTO PROGRAM

CHANNEL EDIT

MANUAL FINE TUNE

FACTORY RESET

LANGUAGE

TUNER MODE

AUTO PROGRAM

CHANNEL EDIT

MANUAL FINE TUNE

FACTORY RESET

INSTALL

LANGUAGE

TUNER MODE

AUTO PROGRAM

CHANNEL EDIT

MANUAL FINE TUNE

FACTORY RESET cable

START?

H

ELPFUL

H

INT

• Immediately after unpacking and plugging in your new television, run the auto

program function to set up the TV for the broadcast or cable channels available in

your area. If you do not run the auto program function to set up the channels ,

your television may not operate properly.

• After you’ve run Auto Program, check out the results. Press the CH+ or the

CH- button and see which channels you can select.

• Remember, an antenna or cable TV signal must first be connected to your LCD TV.

AUTO STORE

PLEASE WAIT

PROG.FOUND

CHANNEL

0

3

5

C

ABLE

B

OX

(

WITH

RF I

N

/ O

UTPUTS

):

4

5

1

2

3

Connect the Cable TV signal to the IN jack (or RF IN or CABLE

IN) on the Cable Box.

Connect an RF coaxial cable (not supplied) to the OUT jack (or

TO TV or RF OUT) of the Cable Box.

Connect the other end of the coaxial cable to one end of the supplied L-Adapter as shown, and connect the other end of the adapter to the TV jack on the LCD TV.

Plug the DC adapter into the DC IN 16V jack on the LCD TV.

Plug the power cable into an outlet and switch TV set on.

Set the Channel 3/4 (or Output channel) switch of the Cable Box to 3 or 4. Set the TV to the same channel. When watching TV programming, change channels at the Cable Box, not the LCD TV.

The Cable TV signal from the Cable Company

� �

CABLE

IN

TO TV

OUTPUT

CH

3 4

�

�

L-Adapter

Side Jack Panel of

� elevision

75 �

Coaxial

Cable

H

ELPFUL

H

INT

• Immediately after unpacking and plugging in your new television,

run the auto program function to set up the TV for the broadcast

or cable channels available in your area. If you do not run the auto

program function to set up the channels , your television may not

operate properly.

• Please make sure that you have selected the TV mode with source key

on your remote control, before installing TV channels.

�

DC Adapter

Power

Cable

VGA

PC

C

ABLE

B

OX

(

WITH

A

UDIO

/ V

IDEO

O

UTPUTS

):

This connection will supply stereo sound to the LCD TV.

1

2

Connect the Cable TV signal to the IN jack (or RF IN or CABLE

IN) on the Cable Box.

Using an RCA-type video cable (not supplied) connect one end of the video cable to the Video Out jack of the Cable Box. Connect the other end of the cable to the yellow VIDEO jack on the side of the TV. Video cables are usually marked with yellow and are available from Magnavox or electronics retailers. Video jacks on most equipment are yellow.

3

Using RCA-type, stereo audio cables (not supplied), connect one end of the cables to the left and right Audio Out jacks of the Cable

Box. Connect the other end of that cable to the Audio jack on the side of the LCD TV. Audio cables are usually marked with red and white and are available from Magnavox or electronics retailers. The right audio jack is red and the left audio jack is white. Match the cable colors to the jack colors.

4

Plug the DC adapter into the DC IN 16V jack on the LCD TV.

Plug the power cable into an outlet and switch TV set on.

�

DC Adapter

Power

Cable

VGA

PC

Cable

TV signal

�

Audio Cable

�

Note: Use the Source button on the remote control to tune to the AV channel for the cable box signal. Once tuned, change channels at the cable box, not the television.

CABLE

IN

TO

TV

OUTPUT

CH

3 4

L

AUDIO

OUT

R

Cable Box

VIDEO

OUT

Video Cable

S - VIDEO

AUDIO

�

VIDEO

Side Jack Panel of �elevision

6

S-V

IDEO

C

ONNECTIONS

The S-Video connection on the rear of the LCD TV can provide you with better picture detail and clarity for the playback of accessory sources such as DBS (digital broadcast satellite), DVD (digital video discs), video games, and VHS VCR (video cassette recorder) tapes than the normal antenna picture connections.

1

Connect an S-Video cable to the S-VIDEO jack of the other equipment (DVD Player, Camcorder, etc.) and to the S-VIDEO jack on the rear of the LCD TV.

2

Connect RCA-style audio cables (usually red and white) to the

AUDIO OUT (left and right) jacks on the other equipment.

Connect the other end of the cables to the AUDIO jack on the side of the LCD TV.

3 2

Audio Cable

3

Plug the DC Adapter into the DC IN 16V jack on the LCD TV.

Plug the power cable into an outlet. Turn on the LCD TV and other equipment.

4

5

Press the Source buttons to set the LCD TV to its S-VIDEO mode.

Press PLAY on the other equipment to view its material on the

LCD TV.

Note:

• The Magnavox LCD TV remote control can not be used to operate other video/audio equipment.

• The Audio jack of AV IN is shared between Video (CVBS) and S-Video signals. If Audio and Video

is connected to S-Video input, you can still hear sound if you select Video via Source select, even

there appears no image on screen.

VCR or External

Accessory Device

(with S-Video

Output)

S - VIDEO

AUDIO

VIDEO

Jack Panel

Side of Television

1

S- Video

Cable

OUT

R AUDIO L

IN

OUT S -V HS OUT

V IDE O

IN

ANT E NNA

OUT

3 5

4

M E N U

SOURCE

C C

OK

P I P

C

OMPONENT

(HD) C

ONNECTIONS

Component Video input provide the highest possible color and picture resolution in the playback of digital signal source material, such as with DVD players. If you are using a HD (High Definition) receiver that can transmit high definition programming, the TV can accept those signals through the Component input located on the bottom of the TV.

1

Connect the component (Y, Pb, Pr) Video OUT jacks from the

DVD player (or similar device) to the COMP(onent) VIDEO Input jacks on the bottom of the LCD TV.

2

Connect the red and white AUDIO CABLES to the Audio (left ad right) output jacks on the rear of the accessory device to the

AUDIO IN jack. Connect the other end of the cable to the Audio jack on the rear of LCD TV.

3

Plug the DC Adapter into the DC IN 16 V jack on the LCD TV.

Plug the power cable into an outlet. Turn on the LCD TV and other equipment.

4

5

Press the SOURCE button on the remote control to select HD.

HD will appear in the upper left corner on the TV screen.

Insert a DVD disc into the DVD player and press the PLAY button on the DVD Player.

Note:

• The Magnavox LCD TV remote control can not be used to operate

other video/audio equipment.

�

�����������

�

���������

������������

������������������

�������

�

�����

��� ���

�����

�

���

�

�

����������

��

��

ACCESSORY DEVICE

EQUIPPED WITH COMPONENT

VIDEO OUTPUTS.

�

�

�����������

�

7

�

M E N U

SOURCE

C C

OK

P I P

PC (M

ONITOR

) I

NPUTS

:

3

4

This LCD TV can be used as a PC. Your computer will have to be equipped with a VGA type video output and VGA cable.

1

Connect one end of the VGA Video cable (not supplied) to the

Monitor (video) output on the computer, while connecting the other ends to the VGA INPUT jack on the LCD TV.

2

Although audio connections are not required, the LCD TV can reproduce the computers audio out by an AUDIO ADAPTER to the Audio output jack on the computer (if available) while connecting the other ends of the Audio cables to the PC AUDIO

Jacks on the bottom of the TV.

Plug the DC Adapter into the DC IN 16V jack on the LCD TV. Plug the power cable into an outlet. Turn on the LCD TV and PC.

Press the SOURCE button until PC MODE appears on the screen.

�

�����������

�

���

�����

���������

������������

�

�

Side Jack Panel

�

M E N U

SOURCE

C C

OK

P I P

�

8