Kobalt 320541 manual

ITEM #0476123
5 GAL. ELECTRIC AIR COMPRESSOR
MODEL #0320541
Français p. 14
KOBALT® and the K Design® are registered
trademarks of LF, LLC. All Rights Reserved.
Español p. 27
ATTACH YOUR RECEIPT HERE
Serial Number
Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST,
Monday - Friday.
kobalttools.com
AB13664C
1
TABLE OF CONTENTS
2
Package Contents.......................................................................................................... 3
Part Description.............................................................................................................. 4
Safety Information.......................................................................................................... 5
Preparation....................................................................................................................
6
Operating Instructions.................................................................................................... 7
Care and Maintenance................................................................................................... 8
Troubleshooting.............................................................................................................. 9
Warranty......................................................................................................................... 11
Replacement Parts List.................................................................................................. 12
PRODUCT SPECIFICATIONS
COMPONENT
Power
Pump/Motor
Tank Capacity
Cut-in Pressure
Cut-out Pressure
SCFM @ 40 PSI
SCFM @ 90 PSI
Power Cord
SPECIFICATIONS
120 V / 60 Hz / 14.5 A
2 HP, oil-free, direct drive, single stage
5 gallons
140 PSI
175 PSI
6.0
5.0
SJT 14 AWG / 72 in. length
Note: Avoid the use of extension cords whenever possible. If an extension cord must be used, it must
have a minimum wire size of 12 AWG, and must be no longer than 30 ft. Use only a 3-wire extension cord that has a 3-prong grounding plug, and plug it into a 3-holed outlet that is suitable for
the compressor’s plug.
kobalttools.com
2
PACKAGE CONTENTS
K
B
L
C
J
D
G
H
F
E
A
H1
I
PART
A
B
C
D
E
F
G
H
H1
I
J
K
L
DESCRIPTION
Electric motor and pump (inside)
ON/OFF switch
Quick coupler
Regulated pressure gauge
Tank pressure gauge
Air pressure regulator
Pressure relief valve
Air tank
Fixed handle (Connected to Air tank)
Drain valve
Power cord
Sliding handle
Cam lock
QUANTITY
1
1
2
1
1
1
1
1
1
1
1
1
2
kobalttools.com
3
PART DESCRIPTION
PART
PART NAME
PART DESCRIPTION
A
Electric motor and pump
The motor is used to power the pump. The pump is
used to compress the air and discharge it into the tank
via the piston moving up and down in the cylinder.
This switch turns on the compressor and is operated
manually. When in the ON position, it allows the
compressor to start up or shut down automatically,
without warning, upon air demand. Always set this
switch to OFF when the compressor is not being used
and before unplugging the compressor.
For this compressor, the quick coupler is also used as
the air line outlet. The outlet is used to connect the 1/4
in. NPT air hose.
The gauge is used to measure the regulated outlet
pressure.
B
ON/OFF switch
C
Quick coupler
D
Regulated pressure gauge
E
Tank pressure gauge
F
Air pressure regulator
G
Pressure relief valve
H
Air tank
I
Drain valve
The drain valve is used to remove moisture from the air
tank after the unit is shut off.
J
Power cord
This product is for use on a nominal 120-volt circuit
and should be grounded. A cord with a grounding plug
must be used. Make sure the product is connected to
adapter should be used with this product.
The gauge is used to measure the store air pressure
level of the tank. It is not adjustable by the operator, and
does not indicate line pressure.
The regulator is used to adjust line pressure to the tool
you are using. Turn the knob clockwise to increase
pressure and counterclockwise to decrease pressure.
The valve is used to prevent system failures by relieving
pressure from the system. When the pressure reaches
the preset level, the pressure switch will not shut down
the motor, it will automatically pop open or you can pull
the ring on the valve to open.
The tank is used to store the compressed air.
Grounded
outlet
Plug
Grounding Pin
K
Sliding handle
This handle is height adjustable for easier mobility.
L
Cam lock
The cam lock is used to lock the sliding handle.
kobalttools.com
4
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product. If you have any questions regarding the product, please call customer service at
1-888-3KOBALT, 8 a.m. - 8 p.m., EST, Monday - Friday.
Safety Symbols
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols
and the explanations that accompany them deserve your careful attention and understanding. The
safety warnings DO NOT, by themselves, eliminate any danger. They are not substitutes for proper
accident-prevention measures.
DANGER: Someone will be seriously injured or killed if the safety information is not followed.
WARNING: Someone will be seriously injured or killed if the safety information is not followed.
CAUTION: Someone may be injured if the safety information is not followed.
User Safety
DANGER
Improper installation of the grounding plug will result in a risk of electric shock. If repair or
terminal. The grounding wire has a green outer surface.
WARNING
!"$%&
motor and pressure switch to produce sparks while operating. If sparks come into contact with
$'
"'"*
far from the spray area as possible. Always operate the compressor in a well-ventilated area.
!""+
national codes. To avoid electric shock, never use an electric air compressor outdoors when it is
raining or on a wet surface.
!"!""'"
use to reduce rusting. Do not weld, drill or modify the air tank of this compressor. Welding or
""$:
condition. If a leak is detected in the tank, replace the tank immediately.
!";+
pressure from the system before servicing the compressor or when the compressor is not in use.
Do not use the unit with the shrouds removed. Contact with moving parts could cause serious
injury.
Risk of bursting. Check the maximum pressure rating in the manual or the serial tag label.
Compressor outlet pressure must be regulated so as to never exceed the maximum pressure
rating. Relieve all pressure through the hose before removing or attaching accessories.
kobalttools.com
5
SAFETY INFORMATION
!"';<
preset at the factory for the maximum pressure of this unit. If the pressure switch or the relief
valve are tampered with, personal injury or property damage may occur.
!"<<
injuries, do not touch the pump, manifold or transfer tube while the unit is running. Allow the parts
to cool before handling or servicing. Keep children away from the compressor at all times.
!"!$
the safety instructions. Use a respirator mask if there is a chance of inhaling anything you are
spraying. Never directly inhale the compressed air produced by a compressor.
!";++
&=>?X
compressor. Never point the nozzle or sprayer toward a person or any part of the body. If the
spray penetrates the skin, serious injury may occur.
$$"
"XY
&
Z
concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer,
birth defects, or other reproductive harm. Wear protective gear.
CAUTION
<"X=[
cooling.
&""
or worn spots and replace if necessary.
+\
hearing loss.
]
or elevated position that could allow the unit to fall or be tipped over.
PREPARATION
Preparing for Startup
1
B
WARNING: Risk of bursting. Too much air
pressure causes a hazardous risk of bursting. Check
the manufacturer’s maximum pressure rating for air
tools and accessories. The regulator outlet pressure
must never exceed the maximum pressure rating.
a. Set the ON/OFF switch (B) to the OFF position.
C
F
b. Turn the air pressure regulator knob (F) counterclockwise until it stops.
c. Attach air hose/accessories or air tools (not
included) to the quick coupler (C).
kobalttools.com
6
OPERATING INSTRUCTIONS
1. Starting up the Compressor
1
B
WARNING: High temperatures are generated
by the electric motor and the pump. To prevent burns
or other injuries, DO NOT touch the compressor
while it is running. Allow it to cool before handling or
servicing. Keep children away from the compressor
at all times.
J
F
WARNING: When adjusting from a higher to a
lower pressure, turn the knob counterclockwise past
the desired setting. Then turn clockwise to reach the
desired pressure. Do not exceed operating pressure
of the tool or accessory being used.
a. Close the drain valve (I) by turning clockwise.
b. Plug in the power cord (J).
c. Set the ON/OFF switch (B) to the ON position
and allow tank pressure to build. Motor will stop
when tank pressure reaches “cut-out” pressure.
d. Turn the air pressure regulator (F) clockwise until
desired pressure is reached.
e. The compressor is ready for use.
2. Shutting Down the Compressor
II
2
B
WARNING: To avoid personal injury, always
shut off and unplug the unit and relieve all air
pressure from the system before performing any
service on the air compressor.
WARNING: Risk of unsafe operation. The
unit cycles automatically when power is on. When
performing maintenance, you may be exposed to
voltage sources, compressed air or moving parts.
Personal injuries can occur. Before performing any
maintenance or repair, disconnect the power source
from the compressor and bleed off all air pressure.
J
G
CAUTION: Escaping air and moisture can propel debris that may cause eye injury. Wear
safety goggles when opening the drain valve.
a. Set the ON/OFF switch (B) to the OFF position.
b. Unplug the power cord (J).
c. Reduce the pressure in the tank through the outlet hose. Pulling the pressure relief valve (G)
and keeping it open will also reduce the pressure in the tank.
d. Tip the compressor so the drain valve (I) is at the bottom of the tank. Then open the drain
valve counterclockwise to allow moisture to drain from the tank.
kobalttools.com
7
OPERATING INSTRUCTIONS
3. Moving the Air Compressor
3
CAUTION: To avoid personal injury, DO NOT
grab only the sliding handle (K) to lift the whole unit.
If you want to lift the unit, please make sure you
$^_X`
(K).
Use the following instructions to use the sliding
handle (K) and wheels to move the unit.
K
Lock
Unlock
L
a. Unlock the two cam locks (L) as shown in the
illustration.
H1
b. Slide the handle (K) upward to the desired
height.
c. Lock the two cam locks (L) in place.
CARE AND MAINTENANCE
WARNING: To avoid personal injury, always shut off and unplug the unit and relieve all air
pressure from the system before performing any service on the air compressor.
Regular maintenance will ensure trouble-free operation. The items listed here should be inspected on
a regular basis.
On a daily basis, drain the tank to prevent corrosion from forming inside
the tank. Drain the condensation at the end of every day. Wear protective
goggles. Relieve the air pressure in the system and then open the drain
valve (I) on the bottom of the tank.
I
On a daily basis, pull the pressure relief valve (G) to ensure that it is
operating properly and to clear the valve of any possible obstructions.
+{<
"
\
soapy water.
Check all connections to ensure they are tight. A small leak from any part of the compressor
will reduce the unit’s performance. Spray a small amount of soapy water around the area of the
suspected leak with a spray bubble. If bubbles appear, repair or replace the faulty component.
Do not overtighten any connections.
Before storing the unit for a long period, do the following:
Use an air blow gun (not included) to clean all dust and debris from the compressor.
Disconnect and coil the power cord.
Pull the pressure relief valve to release all pressure from the tank.
Drain all moisture from the tank.
Cover the entire unit to protect it from moisture and dust.
kobalttools.com
8
TROUBLESHOOTING
PROBLEM
There is low
pressure, not
enough air, or the
compressor does
not stop.
POSSIBLE CAUSE
1. The drain valve is open.
CORRECTIVE ACTION
1. Close the drain valve.
=<"
=}"
<"
DO NOT OVERTIGHTEN.
3. There is a prolonged or excessive
use of air.
3. Decrease the amount of air used.
4. The compressor is not large enough. 4. Check the air requirement of the
accessory. If it is higher than the
CFM and the pressure supplied by
the compressor, you need a larger
compressor. Most accessories are
rated at 25% of the actual CFM
while running continuously.
Air leaks from the
regulator or the
regulator does
not regulate air
pressure.
The regulated
pressure gauge
reading drops
when the air
accessory is being
used.
5. There is a hole in the air hose.
5. Check and replace if necessary.
6. The tank leaks.
6.
7. The seals are blown.
7. Replace the compressor assembly.
8. The valve leaks.
8. Replace the compressor assembly.
9. There is a leaking or worn piston.
1. The internal parts of the regulator
are dirty or damaged.
9. Replace the compressor assembly.
1. Replace the regulator or internal
parts.
1. This is normal.
1. If the pressure drops too low,
adjust the regulator while the
accessory is used.
WARNING: Immediately
replace the tank. DO NOT attempt
to repair.
2. The compressor is not large enough. 2. Check the air requirement of the
accessory. If it is higher than the
CFM and the pressure supplied by
the compressor, you need a larger
compressor. Most accessories are
rated at 25% of the actual CFM
while running continuously.
The pressure relief 1. The tank pressure exceeds the
1. Replace the pressure switch.
valve opens.
normal rating pressure.
2. The pressure switch is stuck.
2. Replace the pressure switch.
kobalttools.com
9
TROUBLESHOOTING
PROBLEM
The motor will not
run.
POSSIBLE CAUSE
1. Tank pressure exceeds the preset
pressure switch limit.
CORRECTIVE ACTION
1. The motor will start automatically
when the tank pressure drops
below the tank cut-in pressure.
2. The fuse is blown or the circuit
breaker tripped.
2. Replace the blown fuse or reset
the circuit breaker. Do not use
a fuse or circuit breaker with a
your branch circuit.
Check for proper fuse; type T fuse
is acceptable.
Check for low voltage and proper
extension cord size.
Disconnect other applications
from the circuit. Operate the
compressor on a dedicated circuit.
3. The check valve is stuck in the open 3. Remove and clean or replace.
position.
4. The wire gauge in the cord is wrong
or the extension cord length is
excessive.
4. Check for proper gauge and
extension cord length.
5. There are loose electrical
connections.
5. Contact an authorized service
center.
6. The motor’s thermal overload
protection has tripped.
6. Turn the air compressor off, unplug
the power cord and wait until the
motor has cooled down. Plug in
the power cord only after the motor
has cooled down; however wait
"
the thermal overload protector has
recovered.
7. The motor, capacitor or safety
valve is defective.
7. Have the compressor serviced by
%
kobalttools.com
10
ONE YEAR LIMITED WARRANTY
This product is guaranteed for a period of one year from the date of original retail purchase against
defects in materials and workmanship.
Subject to the conditions and limitations described below, this product, if returned to us with proof
of purchase within the stated warranty period and if covered under this warranty, will be repaired or
^%`€
cost of any repair or replacement and any costs of labor relating thereto.
This warranty is subject to the following conditions and limitations:
a. A bill of sale verifying the purchase and purchase date must be provided.
b. This warranty will not apply to any product or part which is worn or broken or which has
become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper
installation, operation or maintenance (as outlined in the applicable owner’s manual or
operating instructions) or which is being used for industrial, professional, commercial or rental
purposes.
c. This warranty will not apply to normal wear and tear or to expendable parts or accessories
that may be supplied with the product which are expected to become inoperative or unusable
after a reasonable period of use.
d. This warranty will not apply to routine maintenance and consumable items such as, but not
[
adjustments.
e. This warranty will not apply where damage is caused by repairs made or attempted by others
(i.e. persons not authorized by the manufacturer).
f.
This warranty will not apply to any product that was sold to the original purchaser as a
^`
g. This warranty will not apply to any product or part thereof if any part from another
manufacturer is installed therein or any repairs or alterations have been made or attempted by
unauthorized persons.
h. <$
limited to, scratches, dents, paint chips, or to any corrosion or discoloring by heat, and
abrasive chemical cleaners.
i.
<
another company, which shall be covered under the product manufacturer warranty, if any.
kobalttools.com
11
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-888-3KOBALT, 8 a.m. - 8 p.m., EST,
Monday - Friday
28
15
16
17
18
19
20
21
29
30
31
22
14
32
23
24
12
13
33
25
11
26
27
10
9
8
6
7
5
3
34
4
35
2
36
1
48
PART
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PART NAME
Front shroud
Side vent panel
Fan
Electric motor and pump
!?Y
=‚Y
+
Rubber sleeve
Back shroud
Screw M6x16
Nut M6
Pressure relief valve
Control panel
Screw M5x15
47
45
46
PART #
CE0202S.60.04
CE0202S.60.05
MI0501.00.09
A2410260311
5612-0090-01
5612-0100-01
CE0202S.60.20
CE0202S.60.06
CE0202S.60.03
J0800500033
J2020550033
WCFAAQ.02.00
CE0202S.70.01
J0800510033
44
43
42
41
40
39
PART PART NAME
15
Pressure gauge
(Regulated/Tank)
37
PART #
€}Zƒ„…Y=‚Y
16
17
18
19
20
Air pressure regulator
Rubber hose
Quick coupler
Flexible tube
Self-tapping screw
ST3.9x16
€}\+<ZYXY?
CE0202S.70.10
5106-0010-01
CE0202S.60.10
J0780270167
21
22
23
Check valve
Plug
Self-tapping screw
ST3.9×12
€}\+'…Y=Y=
5017-0010-01
J0780730033
24
25
26
Switch knob
Pressure switch
Power cord
CE0202S.00.03
€}'†Z‡Yˆ?‚
CE0202S.30.10
kobalttools.com
12
38
REPLACEMENT PARTS LIST
PART
27
28
29
30
31
32
33
34
35
36
37
PART NAME
Bleeding tube
Air tank
Cam lock assembly I
Handle Grip
Sliding handle
Cam lock assembly II
Screw M8x8
Sleeve
Wheel
Cotter pin Ø5x25
Bolt M8x45
PART #
CE0202S.40.00
CE0202S.10.00
CE0202S.50.10
CC0701.00.04
CE0202S.50.01
CE0202S.50.20
J0780600033
CE0202S.50.02
CE0202S.20.00
J2840560033
J0800490033
PART
38
39
40
41
42
43
44
45
46
47
48
PART NAME
Lock nut M8
Drain valve
Foot retainer
Rubber foot
Bolt M8x50
Screw M6x16
Lock nut M10
Washer Ø10
Cushion pad
Bolt M10x40
Mount plate
PART #
J2020520033
5105-0030-01
CE0202S.00.01
CE0202S.00.02
J0800460033
J0800500033
J2020540033
J2980590033
CE0202S.60.02
J0800480033
CE0202S.60.01
Printed in China
Kobalt® is a registered trademark of LF, LLC. All Rights Reserved.
kobalttools.com
13
ARTICLE #0476123
COMPRESSEUR D’AIR
ÉLECTRIQUE DE 18,9 L
MODÈLE #0320541
KOBALT® et le motif K® sont des marques de commerce
déposées de LF, LLC. Tous droits réservés.
JOIGNEZ VOTRE REÇU ICI
Numéro de série
Date d’achat
Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article
au détaillant, appelez notre service à la clientèle au 1 888 3KOBALT (1 888 356-2258),
entre 8 h et 20 h (HNE), du lundi au vendredi.
kobalttools.com
14
TABLE DES MATIÈRES
Caractéristiques du produit.............................................................................................
15
Contenu de l’emballage..................................................................................................
16
Description des pièces....................................................................................................
17
Consignes de sécurité.....................................................................................................
18
Préparation....................................................................................................................
19
Mode d’emploi................................................................................................................
20
Entretien.........................................................................................................................
21
Dépannage.....................................................................................................................
22
Garantie.........................................................................................................................
24
Liste des pièces de rechange.........................................................................................
26
CARACTÉRISTIQUES DU PRODUIT
COMPOSANTES
Alimentation
Pompe/moteur
Capacité du réservoir
Point d’enclenchement
Point de déclenchement
pi3/min à 40 lb/po2
pi3/min à 90 lb/po2
Cordon d’alimentation
CARACTÉRISTIQUES
120 V/60 Hz/14,5 A
2 HP, sans huile, à entraînement direct, à un seul étage
18,9 litres
140 lb/po2
175 lb/po2
6,0
5,0
SJT 14 AWG/182,88 cm de longueur
Note: Dans la mesure du possible, évitez d’utiliser une rallonge. Si l’emploi d’une rallonge s’avère
nécessaire, son calibre doit être d’au moins 12 AWG et sa longueur ne doit pas excéder 9,14
‰: Š%Š { ‹ ‹ :[%‹
kobalttools.com
15
CONTENU DE L’EMBALLAGE
K
B
L
C
J
D
G
H
F
E
A
H1
I
PIÈCE
A
B
C
D
E
F
G
H
H1
I
J
K
L
DESCRIPTION
Moteur électrique et pompe (à l’intérieur)
Interrupteur
Raccord à branchement rapide
Manomètre régulé
Jauge de pression de réservoir
Régulateur de pression d’air
Soupape de décharge
Réservoir d’air
Š$^$ŠŠ{`
Robinet de vidange
Cordon d’alimentation
Poignée coulissante
Attache Camloc
QUANTITÉ
1
1
2
1
1
1
1
1
1
1
1
1
2
kobalttools.com
16
DESCRIPTION DES PIÈCES
PIÈCE
NOM DE LA PIÈCE
A
Moteur électrique
et pompe
B
Interrupteur
C
DESCRIPTION DES PIÈCES
Le moteur sert à alimenter la pompe. La pompe sert à
comprimer l’air et à le refouler dans le réservoir par la course
ascendante et descendante d’un piston dans le cylindre.
Cet interrupteur met en marche le compresseur et est activé
manuellement. Lorsqu’il est en position ON (position de marche),
le compresseur démarre et s’arrête automatiquement, sans
avertissement, à la suite d’une demande d’air. Mettez toujours
cet interrupteur en position OFF (position d’arrêt) lorsque vous
n’utilisez pas le compresseur ou avant de le débrancher.
Raccord à branchement Dans ce compresseur, le raccord à branchement rapide
sert également de sortie à la conduite d’air. Cette sortie
rapide
‹‹‹<Œˆ‚
D
Manomètre régulé
Le manomètre sert à mesurer la pression de sortie régulée.
E
Jauge de pression
de réservoir
Le manomètre sert à mesurer la pression de l’air emmagasiné
dans le réservoir. Vous ne pouvez pas le régler et il n’indique
pas la pression de conduite.
F
Régulateur de
pression d’air
G
Soupape de décharge
H
Réservoir d’air
Le régulateur sert à régler la pression de conduite vers l’outil
utilisé. Tournez le bouton dans le sens des aiguilles d’une
montre pour accroître la pression, ou dans le sens contraire
des aiguilles d’une montre pour la réduire.
‡‹Š{
prévenir les pannes. Lorsque la pression atteint un niveau
préétabli, si l’interrupteur n’a pas coupé le moteur, la soupape
s’ouvre automatiquement. Vous pouvez également l’ouvrir
manuellement en tirant sur son anneau.
Le réservoir sert à emmagasiner l’air comprimé.
I
Robinet de vidange
Le robinet de vidange sert à purger l’humidité du réservoir d’air
après l’arrêt de l’unité.
J
Cordon d’alimentation
Cet appareil doit être utilisé sur un circuit d’une tension
nominale de 120 V et mis à la terre. Vous devez utiliser un
{{‹
Assurez-vous de brancher l’appareil sur une prise ayant les
Š%%{:{
pour brancher l’appareil.
Prise mise
à la terre
Fiche
Broche de mise à la terre
K
Poignée coulissante
La hauteur de cette poignée est réglable pour faciliter les
déplacements.
L
Attache Camloc
L’attache Camloc sert à bloquer la poignée coulissante.
kobalttools.com
17
CONSIGNES DE SÉCURITÉ
Assurez-vous de lire et de comprendre l’intégralité du présent manuel avant de tenter d’assembler,
d’installer ou d’utiliser l’article. Si vous avez des questions, veuillez téléphoner à notre service à la
clientèle au 1 888 3KOBALT, entre 8 h et 20 h (HNE), du lundi au vendredi.
Symboles relatifs à la sécurité
Les symboles relatifs à la sécurité servent à attirer votre attention sur les dangers possibles. Vous devez
prêter une attention particulière à ces symboles ainsi qu’aux explications qui sont fournies et bien les
comprendre. Pour éliminer tout danger, vous devez respecter les messages d’avertissement. Ces
messages ne remplacent toutefois pas les mesures appropriées de prévention d’accidents.
DANGER : Le non-respect des consignes de sécurité occasionnera des blessures graves ou mortelles.
AVERTISSEMENT : Le non-respect des consignes de sécurité occasionnera des blessures graves
ou mortelles.
ATTENTION : Le non-respect des consignes de sécurité peut occasionner des blessures.
Sécurité des utilisateurs
DANGER
‡Š%‹‘%Š%
{ŠŠŠ:
‹{^`‡‹
AVERTISSEMENT
!%{${:;%
Il est normal que le moteur et que le pressostat produisent des étincelles durant le fonctionnement.
Si une étincelle entre en contact avec des vapeurs d’essence ou d’autres solvants, ils peuvent
{$:
:Š{Š<:{
que possible de la zone de vaporisation. Faites toujours fonctionner le compresseur dans un
endroit bien ventilé.
!%Š%‡$’ŠŠ%Š
Š‹$$+{ŠŠ%{:
jamais un compresseur d’air électrique à l’extérieur lorsqu’il pleut, ni sur une surface humide.
!%{Š‡‘Š“:{ŠŠ”
%Š%•:
Š{‡Š{Š
sérieusement sa résistance et engendrer des situations extrêmement dangereuses. Si le réservoir fuit,
remplacez-le immédiatement.
!%+:[;Š
de courant et d’évacuer sa pression avant d’en faire l’entretien, ainsi que lorsque vous ne l’utilisez pas.
N’utilisez pas l’unité lorsque le boîtier est retiré. Un contact avec des pièces en mouvement peut causer
des blessures graves.
!%{Š“Š:${Š%Š
de série. La pression de sortie du compresseur d’air doit être réglée de façon à ne jamais dépasser la
$•:
accessoires.
kobalttools.com
18
CONSIGNES DE SÉCURITÉ
!%{ŠŠ:Š%%%
&ŠŠŠŠŠ‹{$‡
réglage pourrait causer des blessures ou des dommages matériels.
!%–‡ŠŠ–
d’autres blessures, ne touchez pas à la pompe, au collecteur ou au tube de transfert lorsque le compresseur
d’air est en marche. Laissez refroidir les pièces avant de les manipuler ou d’en faire l’entretien. Gardez le
compresseur hors de la portée des enfants en tout temps.
!%{‡:Š%:ŠŠ
peinture ou des matières toxiques. Portez un masque respiratoire s’il y a un risque d’inhalation des matières
vaporisées. N’inhalez jamais directement l’air produit par un compresseur.
!%$$:;ŠŠ‹+
&=>?X
lorsque vous utilisez un compresseur d’air. Ne pointez jamais une buse ou un pulvérisateur vers une
personne ou une partie du corps. Le jet peut causer des blessures graves s’il pénètre la peau.
Š:;{${
:;{%Š{Š”‹XY—2.
“:Š”%::::Š$%
bois, la peinture, le métal, le béton, le ciment ou d’autres matériaux de maçonnerie. Cette poussière contient
souvent des substances chimiques reconnues comme étant la cause de cancers, d’anomalies congénitales
et d’autres problèmes liés aux fonctions reproductrices. Portez l’équipement de protection adéquat.
ATTENTION
<:{Š%;Š
‡{‹ˆY˜>”Š
qui assurera son refroidissement.
Š:‹{%{
“Š:%{Š{{:[
:;%:{‡[
consigne peut entraîner une perte auditive.
‰:;{Š{:;{Š
pourrait tomber ou se renverser.
PRÉPARATION
Préparation au démarrage
1
B
AVERTISSEMENT : Risque d’éclatement. Une
pression d’air trop élevée entraîne un risque d’éclatement.
“Š:$%Š
fabricant des outils pneumatiques et des accessoires.
La pression de sortie du régulateur doit être réglée de
façon à ne jamais dépasser la pression nominale maximale.
a. Mettez l’interrupteur (B) en position OFF
(position d’arrêt).
C
F
b. Tournez le bouton du régulateur de pression d’air (F)
dans le sens contraire des aiguilles d’une montre
jusqu’à ce qu’il s’arrête.
c.
Fixez le tuyau à air, les accessoires ou les
outils pneumatiques (non inclus) au raccord
à branchement rapide (C).
kobalttools.com
19
kobalttools.com
20
">