OSCILLATING

EDGE BELT/SPINDLE

SANDER

Table of Contents

Section Page

Table of Contents ................................. 2

Safety Instructions For Oscillating

Edge Belt/ Spindle Sander .................. 3

Safety Signal Words ............................ 3

Before Using The Sander .................... 3

When Installing Or Moving The

Sander ............................................... 4

Before Each Use ................................. 5

Plan Ahead To Protect Your Eyes,

Hands, Face and Ears ....................... 5

When Sander is Running .................... 7

Before Leaving The Sander ................ 7

Precautions To Take When Sanding

Metals ............................................... 7

Precautions To Take When Sanding

Paint .................................................. 7

Motor Specifications and Electrical

Requirements .................................. 8

General Electrical Connections ........... 8

Power Supply and Motor

Specifications .................................... 8

110-120 Volt, 60 Hz. Tool Information . 9

Motor Safety Protection ..................... 10

Wire Sizes ......................................... 10

Unpacking and Checking Contents . 11

List of Loose Parts ............................. 11

Loose Parts ....................................... 11

Assembly ............................................ 12

Mounting Rubber Feet To Base ........ 12

Parts Storage .................................... 12

Removing the Sanding Belt Assembly 13

Installing the Sanding Belt Assembly 13

Installing Sanding Sleeves Larger than 1/2" Diameter ........................... 14

Installing Sanding Sleeves for the 1/2"

Diameter Sanding Drum .................. 15

Selection Of Spacer Ring Inserts And

Upper Spindle Washers .................. 15

Bolting Oscillating Edge Belt/Spindle

Sander To Workbench .................... 16

Section

Supporting Oscillating Edge Belt/

Page

Spindle Sander to Sawhorses ......... 17

Alignment ........................................... 17

Squaring Front Table ........................ 17

Aligning Belt To Miter Gauge Slot ..... 18

Removing/Installing the Sanding Belt 19

Tensioning and Tracking ................... 19

Getting to Know Your Spindle

Sander ............................................ 20

On-Off Switch .................................... 21

Safety Instructions for Oscillating Edge

Belt/Spindle Sander ...................... 22

Before Using The Sander .................. 22

When Installing Or Moving The

Sander ............................................. 22

Before Each Use ............................... 22

Plan Ahead To Protect Your Eyes,

Hands, Face and Ears .................... 23

When Sander is Running .................. 24

Before Leaving The Sander .............. 25

Precautions To Take When Sanding

Metals ............................................. 25

Precautions To Take When Sanding

Paint ............................................... 25

Basic Sanding Operation .................. 26

Sandpaper Selection ......................... 26

Surface Sanding on the Sanding Belt 27

End Sanding on the Sanding Belt ..... 27

Sanding Curved Edges ..................... 27

Feed Direction ................................... 28

Dust Collection Capability ................. 28

Transporting Sander ......................... 28

Maintenance ....................................... 29

Lubrication ......................................... 29

RIDGID Recommends the Following

Accessories ................................... 29

Wiring Diagram .................................. 29

Troubleshooting ................................ 30

Repair Parts ....................................... 32

Notes .................................................. 35

2

Safety Instructions For Oscillating Edge Belt/

Spindle Sander

Safety is a combination of common sense, staying alert and knowing how your oscillating edge belt/spindle sander works. Read this manual to understand this sander.

WARNING: means if the safety information is not followed someone

could be seriously injured or killed.

CAUTION: means if the safety information is not followed someone may be injured.

Safety Signal Words

DANGER: means if the safety information is not followed someone will be seriously injured or killed.

Before Using The Sander

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known

(to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other masonry products, and

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

WARNING: To reduce the risk of mistakes that could cause serious, permanent injury, do not plug the sander in until the following steps are completed.

• Assembly. (See pages 12-19)

• Learn the use and function of the

ON-OFF switch. (See page 21)

• Review and understanding of all safety instructions and operating procedures in this manual.

• Review of the maintenance methods for this sander. (See page 29)

3

Safety Instructions for Oscillating Edge Belt/

Spindle Sander (continued)

Read the following WARNING labels found on the sander:

When Installing Or Moving The Sander

Avoid dangerous environment.

Use the sander in a dry, indoor place protected from rain. Keep work area well lighted.

To reduce the risk of burns or other fire damage, never use the sander near flammable liquids, vapors or gasses.

To reduce the risk of injury or death from electrical shock:

• Ground the sander. This sander has an approved 3-conductor cord and a

3-prong grounding type plug. Use only 3-wire, grounded outlets rated

120 volts, 15 amperes (amps). The green conductor in the cord is the grounding wire. To reduce the risk of electrocution, Never connect the green wire to a live terminal.

• Make sure your fingers do not touch the plug’s metal prongs when plugging or unplugging the sander.

• Never use this or any power sander for wet sanding. Doing so could cause electrocution, serious injury or worse.

To reduce the risk of injury from unexpected sander movement:

• Always unplug the sander before moving it.

• Put the sander on a firm level surface where there is plenty of room for handling and properly supporting the workpiece.

• Attach rubber feet.

• Support the sander so it does not rock.

• Bolt the sander to its work surface.

Use the fasteners and method shown in “Assembly.” (See page

16.)

• Never stand on tool. Serious injury could occur if the tool tips. Do not store anything above or near the tool where anyone might stand on the tool to reach it.

4

Before Each Use

Inspect your sander. Check for:

• alignment of moving parts,

• binding of moving parts,

• broken or damaged parts,

• work parts that cause a gap larger than 1/16" between work support and sanding surface,

• sanding belt narrower than 4 inches.

Narrower belts uncover parts that could trap your fingers,

• worn or damaged electric cords,

• stable mounting, and

• any other conditions that may affect the way the sander works.

• Remove adjusting keys and wrenches. Form a habit of checking for and removing keys and adjusting wrenches from table top before turning sander on.

If any part is missing, bent, or broken in any way, or any electrical parts don’t work properly, turn the sander off and unplug the sander. Replace damaged, missing, or failed parts before using the sander again.

Disconnect the sander to reduce the risk of injury from accidental starting. Turn switch off, unplug sander and remove the switch key before changing the setup or sanding drum.

Maintain tools with care. Keep the sander clean for maximum and safest performance.

To reduce the risk of injury from jams, slips or thrown pieces:

• Use only recommended accessories.

• Use the correct spacer ring insert.

The opening between the sanding sleeve and insert must be 5/32 of an inch or less. (See page 15)

• All sanding drums, washers and

knobs are tight. No parts should have excessive play prior to operating unit.

• Keep work area clean. Cluttered work surfaces invite accidents. Floor must be clean and dry for stable footing.

Plan Ahead To Protect Your Eyes, Hands, Face and Ears

Dress for Safety

• Any power sander can throw foreign objects into the eyes. This can result in permanent eye damage. Always wear safety goggles, not glasses complying with ANSI Z87.1 (or in

Canada CSA Z94.3-99) shown on package. Everyday eyeglasses have only impact resistant lenses.

They are not safety glasses. Safety goggles are available at many local retail stores. Glasses or goggles not in compliance with ANSI or CSA could seriously hurt you when they break.

• Sanding operations are usually dusty. Wear a dust mask along with the safety goggles.

• Wear nonslip footwear.

• Tie back long hair.

• Roll long sleeves above the elbow.

• Noise levels vary widely. To reduce the risk of possible hearing damage, wear ear plugs or muffs when using sander for hours at a time.

5

Safety Instructions for Oscillating Edge Belt/

Spindle Sander (continued)

• Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can get caught and draw you into moving parts.

Know your sander. Read and understand the owner’s manual and labels affixed to the tool. Learn its application and limitations as well as the specific potential hazards.

Plan your work. Think through how you will hold and maneuver the workpiece against the sanding drum or belt.

Use the right tool. Don’t force tool or attachment to do a job it was not designed to do.

To reduce the risk of injury from accidental contact with moving parts:

• Do not layout, assemble, or setup work on the sander while any parts are moving.

• Reduce the risk of accidental

starting. Make sure switch is “OFF” before plugging sander into a power outlet.

Inspect your workpiece. Make sure there are no nails or foreign objects in the part of the workpiece to be sanded.

Plan the way you will hold the workpiece from start to finish. Reduce the risk of awkward operations and hand positions where a sudden slip could cause finger or hand to move into a sanding surface.

Don’t overreach. Maintain balance and footing.

Keep face and body to one side.

Stay out of line of a possible throwback.

Plan your work to reduce the risk of THROWBACKS - when the workpiece catches the sanding drum and is torn from your hands:

• Make sure there is no debris between the workpiece and its supports.

• When sanding irregularly shaped workpieces, plan your work support so it will not slip and be pulled from your hands.

• Use extra caution with large, very small or awkward workpieces.

• Never use this tool to finish pieces too small to hold by hand.

• Use extra supports (tables, saw horses, blocks, etc.) for any workpieces large enough to tip when not secured to the work surface.

• Never use another person as a substitute for a table extension, or as additional support for a workpiece that is longer or wider that the basic sander table, or to help feed, support or pull the workpiece.

• Sand only one workpiece at a time.

• Clear everything except the workpiece and related support devices off the table before turning the sander on.

• Always feed workpiece from right to left against the direction the sanding sleeve or belt is rotating.

• Do not use drums, sanding sleeves or sanding belts which show visual signs of wear such as grooves, tears or rips.

WARNING: Don’t let familiarity

(gained from frequent use of your sander) cause a careless mistake. A careless fraction of a second is enough to cause a severe injury.

6

When Sander is Running

Before starting your work, watch the sander while it runs. If it makes an unfamiliar noise or vibrates excessively, Stop Immediately. Turn the sander off. Unplug the sander. Do not restart until identifying and correcting the problem.

Never leave tool running unattended.

Before using the sander, make sure the sanding belt turns clockwise, when viewed from above.

Keep children away. Keep all visitors a safe distance from the sander and workpiece.

Don’t force tool. It will perform better and safer at its designed rate. Press workpiece against the sanding sleeve hard enough to begin sanding without bogging down or binding spindle or belt.

Before freeing any jammed material:

• Turn switch “OFF”.

• Unplug the sander.

• Wait for all moving parts to stop.

Before Leaving The Sander

Turn switch off. Don’t leave tool until the unit comes to a complete stop.

Make workshop child-proof.

Remove the yellow switch key. Store it away from children and others not qualified to use the tool. Disconnect master switches. Lock the shop.

Precautions To Take When Sanding Metals

When sanding metals, sparks or hot fragments could cause a fire. To reduce the risk of this:

1. Disconnect any dust collecting hose from the sander.

2. Remove all traces of wood dust from inside the unit before sanding metals.

3. Remove all traces of metal dust from inside the unit before sanding wood again.

Precautions To Take When Sanding Paint

Sanding of lead based paint is not

recommended. It is difficult to control the contaminated dust that could cause lead poisoning.

It is also difficult to identify whether or not a paint contains lead. Therefore, we recommend the following precautions when sanding all paints:

1. Protect your lungs. Wear a dust mask or respirator at all times.

Wear only dust masks that are suitable for working in lead paint sanding environments. Ordinary painting masks do not offer this protection.

2. Do not allow children or pregnant women to enter the work area until paint sanding job is complete and work area is clean.

3. To prevent ingesting contaminated paint particles: Do not eat, drink, or smoke in a work area where paint is being sanded. After sanding paint, wash and clean up before eating, drinking or smoking. Do not leave food, drinks, or tobacco products in the work area where dust can settle on them.

7

Precautions To Take When Sanding Paint

(continued)

4. Protect the environment when sanding paint. Use a dust collection system if possible. Seal the work area with plastic if necessary. Do not track paint dust outside the work area.

5. Thoroughly clean the work area upon completion of paint sanding project. If project lasts for an extended period of time, clean work area often. Items such as sanding dust, vacuum filter bags, plastic drop cloths, etc. should be placed in a sealed container and disposed of properly. Clean all items exposed to sanding dust.

Motor Specifications and Electrical Requirements

General Electrical Connections WARNING: Do not touch the terminals of plug when installing or removing the plug to or from the outlet.

DANGER: To reduce the risk of electrocution:

1. Use only identical replacement parts when servicing.

Servicing should be performed by a qualified service technician.

2. Do not use in rain or where floor is wet.

This tool is intended for indoor use only.

If power cord is worn or cut, or damaged in any way, have it replaced immediately.

Power Supply and Motor Specifications

WARNING: To reduce the risk of electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Your tool is wired at the factory for operation using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15-amp branch circuit. To reduce the risk of shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately.

The A-C motor used on this tool is a relay start motor, having the following specifications: It is wired at the factory for operation on 110-120V AC, 60 Hz. operation.

Rated H.P.

Voltage

Amperes

Hertz (Cycles)

Phase

RPM

3/8

110-120

5.0

60

Single

1725

Rotation of Shaft Clockwise

8

110-120 Volt, 60 Hz. Tool

Information

NOTE: The plug supplied on your tool may not fit into the outlet you are planning to use. Your local electrical code may require slightly different power cord plug connections. If these differences exist refer to and make the proper adjustments per your local code before your tool is plugged in and turned on.

If the grounding instructions are not completely understood, or if you are in doubt as to whether the tool is properly grounded, check with a qualified electrician or service personnel.

WARNING: If not properly grounded, this tool can cause an electrical shock, particularly when used in damp locations, in proximity to plumbing, or out of doors. If an electrical shock occurs there is the potential of a secondary hazard, such as your hands contacting the sanding belt/spindle.

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment grounding conductor and a grounding plug, as shown. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.

A temporary adapter may be used to connect this plug to a 2-pole outlet, as shown, if a properly grounded outlet is not available. This temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.

The green colored rigid ear, lug and the like, extension from the adapter must be connected to a permanent ground such as a properly grounded outlet box.

Improper connection of the equipment grounding conductor could result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Properly

Grounded

3-Prong Outlet

Grounding Lug

3-Prong

Plug

Adapter

3-Prong Plug

Grounding

Prong

Make sure this

Is Connected to a Known

Ground

2-Prong

Outlet

NOTE: The adapter illustrated is for use only if you have a properly grounded 2prong outlet.

NOTE: In Canada the use of a temporary adapter is not permitted by the Canadian

Electrical Code.

9

Motor Specifications and Electrical Requirements

(continued)

Motor Safety Protection

IMPORTANT: To reduce the risk of motor damage, the motor should be blown out or vacuumed frequently to keep sawdust from interfering with normal motor ventilation.

1. Connect this tool to a power source with the appropriate voltage for your model and a 15-amp branch circuit with a 15-amp fuse or circuit breaker. Using the wrong size fuse can damage the motor.

2. If the motor won't start, turn off the power switch immediately and unplug the tool. Check the spindle to make sure it turns freely. If the spindle is free, try to start the motor again. If the motor still does not start, refer to the "Troubleshooting” chart.

3. If the motor suddenly stalls while sanding, turn off the power switch, unplug the tool, and remove the workpiece from the belt/drum. The motor may now be restarted and the sanding finished.

4. Fuses may "blow" or circuit breakers may trip frequently if: a. Motor Is Overloaded-Overloading can occur if you sand too rapidly or make too many start/stops in a short time.

b. Line voltages should not be more than 10% above or below the nameplate voltage. For heavy loads, however, the voltage at motor terminals must equal the voltage specified for your model.

5. Most motor troubles may be traced to loose or incorrect connections, overload, low voltage (such as small size wire in the supply circuit) or to overly long supply circuit wire. Always check the connections, the load and supply circuit whenever motor doesn't work well. Check wire sizes and extension cord length with the Wire Size Chart.

Wire Sizes

NOTE: Make sure the proper extension cord is used and is in good condition.

The use of any extension cord will cause loss of power. To keep this to a minimum and to prevent overheating and motor burn-out, use the table shown to determine the minimum wire size (A.W.G.) extension cord.

Use only 3-wire extension cords with 3prong grounding type plugs and 3-pole receptacles.

Extension Cord

Length

0-25 Ft.

26-50 Ft.

Gauge (A.W.G.)

16

14

10

Unpacking and Checking Contents

1. Remove tool from carton by lifting unit.

2. Place the tool on a secure, stationary work surface and look the tool over carefully.

WARNING: For your own safety, never connect plug to power source outlet, or insert switch key until all assembly steps are complete and until you have read and understood the entire owners manual.

WARNING: To reduce the risk of injury, if any parts are missing, do not attempt to assemble the sander, plug in the power cord, or turn the switch on until the missing parts are obtained and installed correctly.

List of Loose Parts

NOTE: Before beginning assembly, check that all parts are included. If you are missing any part, do not assemble the sander.

Call 1-866-539-1710 or E-mail us at [email protected] if any parts are damaged or missing. Sometimes small parts can get lost in packaging material. Do not throw away any packaging until sander is put together. Check packaging for missing parts before contacting RIDGID.

Item Description Qty.

A Oscillating Edge Belt/

Spindle Sander ................................ 1

B Spacer Ring Inserts

1/2" I.D. ........................................... 1

1" I.D. .............................................. 1

1-1/2" I.D. ........................................ 1

2" I.D. .............................................. 1

C Drums

3/4" x 4-1/2"..................................... 1

1" x 4-1/2"........................................ 1

1-1/2" x 4-1/2" ................................. 1

2" x 4-1/2"........................................ 1

D Sandpaper Sleeves

1/2" x 4-1/2"..................................... 1

3/4" x 4-1/2"..................................... 1

1" x 4-1/2"........................................ 1

1-1/2" x 4-1/2" ................................. 1

2" x 4-1/2"........................................ 1

E Sanding Belt (Installed)

4" x 24" ............................................ 1

F Insert ............................................... 1

G Operators Manual ........................... 1

H Bag of Loose Parts

Containing the following parts:

Rubber feet ........................................ 4

Washer, Flat 21/64 x 1-3/4 x 1/8 ........ 1

Washer, Flat 21/64 x 7/8 x 3/64 ......... 1

Washer, Flat 21/64 x 5/8 x 1/32 ......... 1

Switch Key ......................................... 1

Hex “L” Wrench 3/32 .......................... 1

Hex “L” Wrench 5/32 .......................... 1

Loose Parts

Spacer Ring Inserts

A

E

B

C

1/2" 1" 1-1/2" 2"

Drums and Sandpaper Sleeves

D

F

G H

1/2" 3/4" 1" 1-1/2 "

NOTE: The sander is shipped with the 4" x 24" sanding belt attached.

NOTE: Parts shown are not actual size.

11

2"

Assembly

NOTE: The sander is preassembled except for the attachment of the rubber feet.

Mounting Rubber Feet To Base

Place the sander directly on the table surface.

1. From the parts bag locate the four rubber feet.

2. Place the sander on its side so the bottom of the base is facing toward the front.

3. Locate the four holes in each corner of the base and place one of the rubber feet in each of these holes.

4. Position sander in the upright position and apply pressure in the downward position to ensure the feet are inserted securely.

CAUTION: To reduce the risk of injury from tool movement, the supporting surface where sander is mounted should be examined carefully after mounting to insure no movement during use can result. If any tipping or walking is noticed, secure to workbench or supporting surface before operating sander.

Parts Storage

On board storage has been provided for all washers, spacers, drums, sleeves and hex “L” wrenches. All front loaded parts can be protected from incidental dislodging by lowering the table all the way down until it rests against the base and tightening the knob.

Storage for the sanding belt assembly and table insert is provided in the pocket on the rear of the base.

12

Rubber Feet

Removing the Sanding Belt

Assembly

WARNING: To reduce the risk of injury from accidental start, make sure tool is unplugged before removing the sanding belt assembly.

1. Loosen the backstop knob and pivot the backstop out of the way. Tighten the backstop knob.

2. Remove the spindle knob and lift off the sanding belt assembly. NOTE: Knob turns clockwise to loosen.

3. Store assembly in pocket in rear of base.

Spindle

Knob

Backstop

Knob

Sanding Belt

Assembly

Installing the Sanding Belt

Assembly

1. Remove the fan and clean sawdust from inside table recess.

2. Slide the fan onto the motor shaft

(vanes face down) aligning slot with roll pin as shown. The fan is used in all sanding operations.

3. Slide bed assembly down motor shaft.

Align drive drum splines with the slots in the fan. Place bed assembly into the wear plate opening as shown.

4. Tighten spindle knob. Do not overtighten. NOTE: Knob turns counterclockwise to tighten.

5. Install sanding belt (see “Removing/

Installing the Sanding Belt”, page 19).

6. Plug the power cord into the power source and install the key.

Splines

Slots

Fan

Wear

Plate

Fan

Slot

Motor

Shaft

Roll Pin

13

Assembly (continued)

Installing Sanding Sleeves Larger than 1/2" Diameter

WARNING: To reduce the risk of injury from accidental starting, always turn switch “OFF” and remove switch key before removing or replacing the spacer ring inserts, sleeves and drums.

1. Remove the fan and clean sawdust from inside table recess.

2. Slide the fan onto the motor shaft

(vanes face down) aligning slot with roll pin. The fan is used with all drums and sleeves.

3. Install the table insert.

4. Use a straight edge as shown to make sure the table insert is flush with the table.

If necessary adjust the set screws in the table insert with the 3/32 hex “L” wrench provided.

5. Slide the sanding sleeve-rubber drum onto the spindle. NOTE: If the drum is difficult to slide over the spindle, apply talcum powder to the spindle.

6. Position spacer ring insert in the table recess. (See recommended spacer ring insert selection area from table on page

15). Use the smallest spacer ring insert that will fit over the drum.

7. Place desired sanding sleeve on correct drum. NOTE: If the sanding sleeve is difficult to slide over the drum, apply talcum powder to the outside surface of the rubber drum.

8. Install the correct upper spindle washer and tighten the knob. Do not over-

tighten. NOTE: Knob turns counterclockwise to tighten.

9. Plug power cord in the power source and install the yellow switch key.

14

Straightedge

Table

Insert

Knob

Washer

Sanding Sleeve

Sanding Drum

Spacer Ring

Insert

Installing Sanding Sleeves for the

1/2" Diameter Sanding Drum

WARNING: To reduce the risk of injury from accidental starting, always turn switch “OFF”, unplug the sander and remove switch key before removing or replacing the spacer ring inserts, sleeves and drums.

1. Remove the fan and clean sawdust from inside table recess.

2. Slide the fan onto the motor shaft

(vanes face down) aligning slot with roll pin. The fan is used with all sanding operations.

3. Install the table insert.

4. Use a straight edge as shown to make sure the table insert is flush with the table

If necessary adjust the set screws in the table insert with the 3/32 hex “L” wrench provided.

5. Position 15/16" inside diameter spacer ring insert in the table recess.

6. Locate 1/2" sanding sleeve and slide it on the spindle. (Rubber drum is not used.)

7. Install the upper spindle washer and tighten the knob. Do not overtighten.

NOTE: Knob turns counterclockwise to tighten.

8. Plug the power cord in the power source and install the yellow switch key.

Knob

5/8" O.D.

Washer

1/2" Sanding

Sleeve

15/16" I.D.

Spacer Ring

Selection Of Spacer Ring Inserts

And Upper Spindle Washers

WARNING: Using the wrong spacer ring insert may permit small pieces of wood or finger tips to become wedged between the abrasive surface and the insert.

Sanding Sleeve

Diameter

Spacer Ring Insert

Opening Inside Diameter

Upper Spindle Washer

Outside Diameter

1/2 Inch

3/4 Inch

1 Inch

1-1/2 Inch

2 Inch will fit over the drum.

15/16 Inch

• Use the smallest spacer ring insert that

5/8"

1-3/16 Inch

1-11/16 Inch

2-3/16 Inch

7/8"

1-3/4"

• Use the largest upper spindle washer that will not protrude past sanding sleeve.

15

Assembly (continued)

Bolting Oscillating Edge Belt/

Spindle Sander To Workbench

If sander is to be used in a permanent location, it should be fastened securely to a firm supporting surface such as a workbench, with either bolts or drywall screws.

Fastening with bolts

1. Use 1/4" bolts, washers, and nuts (not included). The bolt length should be

1-1/2" plus the thickness of the workbench.

2. Locate and mark the holes where the sander is to be mounted.

3. Drill (4) 3/8" diameter holes through workbench.

4. Place sander on workbench, aligning holes in base with holes drilled in workbench.

5. Insert (4) 1/4" diameter bolts and washers and attach nuts securely.

Fastening with screws

Drive (4) 2-1/2" long screws through the holes in the base and through the workbench. Do not overtighten the screws.

CAUTION: To reduce the risk of injury from tool movement, use either 1/4" diameter screws and nuts or 2-1/2" long screws.

Clamping Oscillating Edge Belt/Spindle Sander To Workbench

An alternative method of mounting is to fasten the sander to a mounting board.

The board should be sufficient size to avoid tipping while in use. Any good grade of plywood or chipboard with a 3/4" thickness is recommended. (Thinner chipboard can break.)

NOTE: For proper stability, holes must be countersunk so screw heads are flush with the surface of supporting board.

15-3/8

"

14-1/4"

16-1/4"

1/4 Dia. Bolt

Holes

Screws Holes

16

Supporting Oscillating Edge Belt/

Spindle Sander to Sawhorses

The sander has provisions for being supported by sawhorses. The sawhorse can be built with the crosspiece either vertical or horizontal. Make sure the sawhorses are secure.

Alignment

Squaring Front Table

WARNING: To reduce the risk of injury from accidental start, make sure tool is unplugged before aligning.

Combination Square

Combination Square Must be True

Tools Needed

1. Use a combination square to check the angle of the front table with the sanding belt. (NOTE: Combination square is not supplied.)

2. If the front table is not 90° to the sanding belt: a. Use the hex wrench provided and

“back out” both #10 set screws located on each side of the table.

b. Loosen the front table lock knob and adjust the front table 90° to the sanding belt.

c. Tighten the front table lock knob.

d. Adjust both set screws to contact the front table.

Draw Light Line on

Board Along This Edge

Should be no Gap or Overlap when Square is Flipped Over in Dotted Position

Combination

Square

Straight Edge of Board

3/4" Thick, This Edge Must

Be Perfectly Straight

Sanding

Belt

3. Adjust detent if necessary a. Loosen the two pan head screws that secure the detent.

b. Adjust detent so that it engages the notches in the bracket table lock.

c. Tighten the two pan head screws.

Front

Table

Bracket

Table Lock

Table

Lock Knob

Detent

#10 Set

Screw

Pan Head

Screws

17

Alignment (continued)

Aligning Belt To Miter Gauge Slot

The sanding belt is installed at the factory; however, check and make sure the belt is parallel to the miter gauge groove:

1. Use a combination square to check the distance from the miter gauge groove to the belt assembly as shown.

2. If adjustment is required, use a 5/32 inch hex “L” wrench provided with unit to loosen the two flat head socket recess screws on the table.

3. Adjust the bed assembly as needed to make it parallel or same distance to the miter gauge slot.

4. Tighten two screws.

Adjust Bed

Assembly

Parallel to

Miter Gauge

Slot

Socket Recess

Screws

18

Removing/Installing the Sanding

Belt

Tensioning and Tracking

WARNING: To reduce the risk of injury from accidental start, make sure tool is unplugged before removing or installing sanding belt.

Some sanding belts have a “directional arrow” on the inside or smooth side. If there is an arrow, the belt must run in the direction of the arrow so the splice will not come apart. If there is no arrow the belt may be put on either direction.

1. Slide the tension lever to the left to release the belt tension.

2. Remove the sanding belt.

Tensioning

Lever

Belt

Tracking

3. Place the replacement sanding belt over the drums as shown. Make sure the belt is centered on both drums.

4. Slide the tension lever to the right to apply belt tension.

5. Plug in the power cord. Insert the yellow switch key and turn the unit “ON” and immediately “OFF”, noting if the belt tends to slide off the drums. If it did not tend to slide off, it is tracking properly.

Clockwise

(Moves Belt Up)

6. If the sanding belt runs down towards the table, turn the tracking knob clockwise 1/4 turn.

7. If the sanding belt, runs up away from the table, turn the tracking knob counterclockwise 1/4 turn.

8. Turn switch “ON” and immediately

“OFF” again, noting belt movement.

Readjust tracking knob if necessary.

Counterclockwise

(Moves Belt

Down)

19

Getting to Know Your Spindle Sander

4

3

Tracking Knob

Spindle Knob

2

Belt Tension Lever

5

Backstop

1

Sanding Belt

6

Front Table

7

Spacer Rings

10

On-Off Switch

Table Adjustment Screws

(Left and Right Side)

9

Front Table

Lock Knob

Detent

8

Sanding Drum(s)/

Sleeves(s)

Slots for

“Saw Horse”

Mounting

15

Table Insert

11

Backstop Knob

12

Dust Collection

Port

WARNING: To reduce the risk of injury from accidental start, turn switch “OFF” and remove plug from power source outlet before making any adjustments.

1. Sanding Belt. Removes material from wood. Oscillates (3/4") up and down to sand faster and prevents burning of the workpiece.

2. Belt Tension Lever. Slide lever left to release the sanding belt tension; slide right to apply belt tension.

3. Tracking Knob. Turning knob counterclockwise causes sanding belt to move towards the table; turning knob clockwise causes sanding belt to move away from the table.

4. Spindle Knob. Loosen knob to

20

14

3/32 Hex “L” Wrench

5/32 Hex “L” Wrench

13

Table Insert/

Sanding Belt

Storage remove sanding belt assembly (or sanding drum) and change to spindle sanding (or belt sanding). NOTE:

Knob has left hand threads. Turn knob clockwise to loosen and counterclockwise to tighten.

5. Backstop. Supports the workpiece on the sanding belt.

6. Front Table. Supports the workpiece.

Can also be tilted for bevel sanding.

7. Spacer Ring. Fits around drum to help support workpiece.

8. Sanding Sleeve/Drum. Removes material from wood. Oscillates up and down to sand faster and prevents burning the workpiece.

9. Table Lock Knob. Loosening knob allows the front table to be tilted for bevel sanding.

10. On-Off Switch

11. Backstop Knob. Loosening knob allows backstop to be pivoted.

12. Dust Collection Port. 2-1/2" opening for wet/dry vac hook-up.

13. Table Insert/Sanding Belt Storage.

Holds table insert or sanding belt when not being used.

14. Hex “L” Wrench. Use 3/32" wrench to adjust front table and table insert.

Use 5/32" wrench to adjust belt to miter gauge slot.

15. Table Insert. Helps to support workpiece when drum sanding.

On-Off Switch

The On-Off switch has a locking feature.

This Feature Is Intended To Help Prevent Unauthorized And Possible Hazardous Use By Children And Others.

1. To turn sander “ON” insert key into switch.

NOTE: Key is made of yellow plastic, located in loose parts bag.

2. Insert finger under switch lever and

Pull end of switch out.

3. To turn sander “OFF”. Push lever in.

WARNING: Never leave the sander unattended until it has come to a complete stop.

4. To lock switch in “OFF” position, hold switch “IN” with one hand. Remove key with other hand.

WARNING: For your own safety, always lock the switch “OFF” when sander is not in use.

Remove key and keep it in a safe place. Also, in the event of a power failure (all of your lights go out) turn switch off, remove the key and store it remote from sander.

CAUTION: Before turning switch on, make sure the belt or drum and sleeve are properly installed.

21

Yellow

Switch Key

Turning

Sander On

On-Off

Switch

Turning

Sander Off

Remove

Yellow Key

Safety Instructions for Oscillating Edge Belt/Spindle Sander

Before Using The Sander

WARNING: To reduce the risk of mistakes that could cause serious, permanent injury, do not plug the sander in until the following steps are completed.

• Assembly. (See pages 12-19)

• Learn the use and function of the

ON-OFF switch. (See page 21)

• Review and understanding of all safety instructions and operating procedures in this manual.

• Review of the maintenance methods for this sander. (See page 29)

When Installing Or Moving The Sander

Avoid dangerous environment.

Use the sander in a dry, indoor place protected from rain. Keep work area well lighted.

To reduce the risk of burns or other fire damage, never use the sander near flammable liquids, vapors or gasses.

To reduce the risk of injury or death from electrical shock:

• Ground the sander. This sander has an approved 3-conductor cord and a

3-prong grounding type plug. Use only 3-wire, grounded outlets rated

120 volts, 15 amperes (amps). The green conductor in the cord is the grounding wire. To reduce the risk of electrocution, Never connect the green wire to a live terminal.

• Make sure your fingers do not touch the plug’s metal prongs when plugging or unplugging the sander.

• Never use this or any power sander for wet sanding. Doing so could cause electrocution, serious injury or worse.

To reduce the risk of injury from unexpected sander movement:

• Always unplug the sander before moving it.

• Put the sander on a firm level surface where there is plenty of room for handling and properly supporting the workpiece.

• Attach rubber feet.

• Support the sander so it does not rock.

• Bolt the sander to its work surface.

Use the fasteners and method shown in “Assembly.” (page 16)

• Never stand on tool. Serious injury could occur if the tool tips. Do not store anything above or near the tool where anyone might stand on the tool to reach them.

Before Each Use

Inspect your sander. Check for:

• alignment of moving parts,

• binding of moving parts, could trap your fingers,

• worn or damaged electric cords,

• stable mounting, and

• broken or damaged parts,

• work parts that cause a gap larger than 1/16" between work support and sanding surface,

• sanding belt narrower than 4 inches.

Narrower belts uncover parts that

• any other conditions that may affect the way the sander works.

22

• Remove adjusting keys and wrenches. Form a habit of checking for and removing keys and adjusting wrenches from table top before turning sander on.

If any part is missing, bent, or broken in any way, or any electrical parts don’t work properly, turn the sander off and unplug the sander. Replace damaged, missing, or failed parts before using the sander again.

Disconnect the sander to reduce the risk of injury from accidental starting. Turn switch off, unplug sander and remove the switch key before changing the setup or sanding drum.

Maintain tools with care. Keep the sander clean for maximum and safest performance.

To reduce the risk of injury from jams, slips or thrown pieces:

• Use only recommended accesso-

ries.

• Use the correct spacer ring

insert. The opening between the sanding sleeve and insert must be

5/32 of an inch or less. (See page

15)

• All sanding drums, washers and

knobs are tight. No parts should have excessive play prior to operating unit.

• Keep work area clean. Cluttered work surfaces invite accidents. Floor must be clean and dry for stable footing.

Plan Ahead To Protect Your Eyes, Hands, Face and Ears

Dress for Safety

• Any power sander can throw foreign objects into the eyes. This can result in permanent eye damage. Always wear safety goggles, not glasses complying with ANSI Z87.1 (or in

Canada CSA Z94.3-99) shown on package. Everyday eyeglasses have only impact resistant lenses.

They are not safety glasses. Safety goggles are available at many local retail stores. Glasses or goggles not in compliance with ANSI or CSA could seriously hurt you when they break.

• For dusty operations, wear a dust mask along with safety goggles.

• Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can get caught and draw you into moving parts.

Know your sander. Read and understand the owner’s manual and labels affixed to the tool. Learn its application and limitations as well as the specific potential hazards.

Plan your work. Think through how you will hold and maneuver the workpiece against the sanding drum or belt.

Use the right tool. Don’t force tool or attachment to do a job it was not designed to do.

• Wear nonslip footwear.

• Tie back long hair.

To reduce the risk of injury from accidental contact with moving parts:

• Roll long sleeves above the elbow.

• Do not layout, assemble, or setup work on the sander while any parts are moving.

• Noise levels vary widely. To reduce the risk of possible hearing damage, wear ear plugs or muffs when using sander for hours at a time.

• Sanding operations are usually dusty. Wear a dust mask along with the safety goggles.

• Reduce the risk of accidental

starting. Make sure switch is “OFF” before plugging sander into a power outlet.

23

Safety Instructions for Oscillating Edge Belt/ Spindle

Sander (continued)

Inspect your workpiece make sure there are no nails or foreign objects in the part of the workpiece to be sanded.

Plan the way you will hold the workpiece from start to finish.

Reduce the risk of awkward operations and hand positions where a sudden slip could cause finger or hand to move into a sanding surface.

Don’t overreach. Maintain balance and footing.

Keep face and body to one side.

Stay out of line with a possible throwback.

Plan your work to reduce the risk of

THROWBACKS - when the workpiece catches the sanding drum and is torn from your hands:

• Make sure there’s no debris between the workpiece and its supports.

• When sanding irregularly shaped workpieces, plan your work support so it will not slip and be pulled from your hands.

• Use extra caution with large, very small or awkward workpieces.

• Never use this tool to finish pieces too small to hold by hand.

• Use extra supports (tables, saw horses, blocks, etc.) for any workpieces large enough to tip when not secured to the work surface.

• Never use another person as a substitute for a table extension, or as additional support for a workpiece that is longer or wider that the basic sander table, or to help feed, support or pull the workpiece.

• Sand only one workpiece at a time.

• Clear everything except the workpiece and related support devices off the table before turning the sander on.

• Always feed workpiece from left to right against the direction the drum sleeve is rotating.

• Do not use drums, sanding sleeves or belts which show visual signs of wear such as grooves, tears or rips.

WARNING: Don’t let familiarity

(gained from frequent use of your sander) cause a careless mistake. A careless fraction of a second is enough to cause a severe injury.

When Sander is Running

Before starting your work, watch the sander while it runs. If it makes an unfamiliar noise or vibrates excessively, Stop Immediately. Turn the sander off. Unplug the sander. Do not restart until identifying and correcting the problem.

Never leave tool running unattended.

Before using the sander, make sure the sanding belt turns clockwise, when viewed from above.

Keep children away. Keep all visitors a safe distance from the sander and workpiece.

Don’t force tool. It will perform better and safer at its designed rate. Press workpiece against the sanding sleeve or belt hard enough to begin sanding without bogging down or binding spindle.

24

Before freeing any jammed material:

• Turn switch “OFF”.

• Unplug the sander.

• Wait for all moving parts to stop.

Before Leaving The Sander

Turn switch off. Don’t leave tool until the unit comes to a complete stop.

Make workshop child-proof.

Remove the yellow switch key. Store it away from children and others not qualified to use the tool. Disconnect master switches. Lock the shop.

Precautions To Take When Sanding Metals

When sanding metals, sparks or hot fragments could cause a fire. To reduce the risk of this:

1. Disconnect any dust collecting hose from the sander.

2. Remove all traces of wood dust from inside the unit before sanding metals.

3. Remove all traces of metal dust from inside the unit before sanding wood again.

Precautions To Take When Sanding Paint

Sanding of lead based paint is not rec-

ommended. It is difficult to control the contaminated dust that could cause lead poisoning.

It is also difficult to identify whether or not a paint contains lead. Therefore, we recommend the following precautions when sanding all paints:

1. Protect your lungs. Wear a dust mask or respirator at all times. Wear only dust masks that are suitable for working in lead paint sanding environments.

Ordinary painting masks do not offer this protection.

2. Do not allow children or pregnant women to enter the work area until paint sanding job is complete and work area is clean.

3. To prevent ingesting contaminated paint particles: Do not eat, drink, or smoke in a work area where paint is being sanded. After sanding paint, wash and clean up before eating, drinking or smoking. Do not leave food, drinks, or tobacco products in the work area where dust can settle on them.

4. Protect the environment when sanding paint. Use a dust collection system if possible. Seal the work area with plastic if necessary. Do not track paint dust outside the work area.

5. Thoroughly clean the work area upon completion of paint sanding project. If project lasts for an extended period of time, clean work area often. Items such as sanding dust, vacuum filter bags, plastic drop cloths, etc. should be placed in a sealed container and disposed of properly. Clean all items exposed to sanding dust.

25

Basic Sanding Operation

Sandpaper Selection

Selecting the correct size diameter, correct size grit, and correct type sandpaper is an extremely important step in achieving a high quality sanded finish. Aluminum oxide, silicon carbide, and other synthetic abrasives are best for power sanding.

Natural abrasives, such as flint and garnet, are too soft for economical use in power sanding.

In general, coarse grit will remove the most material and finer grit will produce the best finish in all sanding operations.

The condition of the surface to be sanded will determine which grit will do the job. If the surface is rough, start with a coarse grit and sand until the surface is uniform.

Medium grit may then be used to remove scratches left by the coarser grit and finer grit used for finishing of the surface.

Always continue sanding with each grit until surface is uniform.

NOTE: Do Not use sander without sandpaper. Doing so will damage the rubber drum.

Select and install the desired sanding sleeve for your particular application.

Sanding sleeves from 1/2" to 2" can be used with this sander. Choose one that is close in size to the workpiece you are sanding. Also install the appropriate spacer ring insert (page 15).

WARNING: Failure to use the correct size spacer ring insert with its matching sanding sleeve could result in fingers being pinched or the workpiece being pulled down between the spacer ring insert and sanding sleeve.

NOTE: The correct size sanding belt is 4" x 24". These belts are available in coarse, medium and fine grits.

1/2" 3/4" 1" 1-1/2" 2"

4" x 24" Sanding Belt

26

Surface Sanding on the Sanding

Belt

WARNING: To reduce the risk of injury from slips, jams or thrown pieces, adjust the backstop to clear the sanding surface by no more than 1/16 of an inch. When checking clearance between the sanding belt and backstop, press the sanding belt flat against the metal bed beneath it.

Hold the workpiece firmly with both hands, keeping fingers away from the sanding belt.

Keep the end butted against the backstop and move the work evenly across the sanding belt. Use caution when sanding very thin pieces.

For sanding long pieces the backstop can be rotated out of the way.

Apply only enough pressure to allow the sanding belt to remove material.

End Sanding on the Sanding Belt

Move the work evenly across the sanding belt. For accuracy, use a miter gauge accessory (not included).

Sanding Curved Edges

Inside curves are best sanded with the sander assembled in the spindle mode.

However, inside curves larger than 1-1/2" may be sanded on the drive drum when in the belt sander mode.

Although it is possible to lightly sand on the idler drum end of the belt sanding assembly, it is not recommended. The idler drum is an integral part of the belt tracking mechanism. It is spring loaded to maintain proper tension. Use of the idler drum to sand curves may cause belt to track improperly.

27

Drive Drum

Idler

Drum

Basic Sanding Operation (continued)

Feed Direction

WARNING: To prevent thrown workpiece, feed workpiece against sanding sleeve from left to right as shown.

The sanding sleeve rotates clockwise.

Feed the workpiece against the sanding sleeve from left to right as shown. When fed from left to right, the rotation of the sanding sleeve sands against the workpiece. If fed in the opposite direction, the rotation forces of the spinning sanding sleeve will tend to throw or bounce the workpiece away from the sanding sleeve.

This could cause loss of control of workpiece or injury.

Dust Collection Capability

A standard 2-1/2" dust exhaust port has been provided to make dustless sanding possible. It is on the rear of your sander as shown. The pickup adapter end of a vacuum hose fits inside the dust exhaust port with a wedge fit.

Even with a dust collection system, it is necessary to periodically clean sanding dust from the recess in the table. Sawdust buildup in the table recess may prevent the belt or spindle from making a complete oscillation, which may cause premature wear.

Transporting Sander

When using your sander in a portable application, it is acceptable to lift and carry sander by the table top by the carry handles. Be careful when transporting to reduce the risk of dislodging accessories, spacer ring inserts, wrench, and upper spindle washers from their respective storage areas.

28

Maintenance

WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet before adjusting or maintaining your sander.

WARNING: To reduce the risk of electrocution or fire, any repairs to electrical systems should be done only by qualified service technicians. Unit must be reassembled exactly to factory specifications.

If power cord is worn or cut, or damaged in anyway, have it replaced immediately.

Frequently blow out or vacuum out any dust that may accumulate inside the motor.

Lubrication

All bearings in tool are self-lubricating.

They require no further lubrication.

RIDGID Recommends the Following Accessories

WARNING: Use only accessories recommended for this sander. Using other accessories may be dangerous.

Size Grit SKU No.

1/2"

3/4"

1"

Fine

Medium

Coarse

Fine

Medium

Coarse

Fine

Medium

Coarse

AC7001

AC7002

AC7003

AC7004

AC7005

AC7006

AC7007

AC7008

AC7009

Do not use any accessory unless you have received and read complete instructions for its use.

Item SKU No.

Miter Gauge................................. AC1021

Switch Key................................... AC1000

Universal Legset.......................... AC9910

Replacement Sanding

Sleeves, 2 pk. ................ See Chart Below

Size

1-1/2"

2"

Grit

Fine

Medium

Coarse

Fine

Medium

Coarse

SKU No.

AC7010

AC7011

AC7012

AC7013

AC7014

AC7015

NOTE: 4" x 24" Replacement sanding belts are available at you local Home

Depot Store.

Wiring Diagram

Green

Black

White

Switch

White

M

A L

Red

Relay

Ground

Screw

Black

29

Motor

Troubleshooting

WARNING: For your own safety, turn switch “OFF”, and remove plug from power source outlet before troubleshooting your sander.

TROUBLE PROBABLE CAUSE REMEDY

Excessive noise

NOTE: The sander will make some noise when it is operating normally

1. Motor gearbox not operating correctly.

1. Consult Authorized Service

Center, any attempt to repair this motor or gearbox may create a hazard unless repair is done by a qualified service technician.

Motor fails to develop full power, starts slowly, or fails to come up to full speed.

NOTE: Low voltage

1. Circuit overloaded with lights, appliances and other motor.

2. General overloading of power company facilities.

3. Motor relay not operating.

1. Do not use sander on heavily loaded circuits

2. Request a voltage check by qualified electrician

Motor overheats 1. Motor overloaded.

3. Have relay replaced. Consult Authorized Service

Center. Any attempt to repair this relay may create a hazard unless repair is done by a qualified service technician.

1. Reduce pressure on workpiece.

Motor stalls (resulting in blown fuses or circuit breakers)

1. Motor relay not operating.

1. Have relay replaced.Consult Authorized Service

Center. Any attempt to repair this relay may create a hazard unless repair is done by a qualified service technician.

2. Request voltage check by qualified electrician

2. Voltage too low. Circuit overloaded or general overloading of power company facilities.

3. Incorrect fuses or circuit breakers in power line.

3. Install correct fuse or circuit breaker.

30

TROUBLE PROBABLE CAUSE REMEDY

Frequent opening of fuse or circuits breaker

Motor will not run

1. Motor overloaded.

2. Incorrect fuses or circuit breaker in power line.

3. Relay not operating.

1. Feed work slower

2. Install correct fuse or circuit breakers.

3. Have relay replaced. Consult Authorized Service

Center. Any attempt to repair this relay may create a hazard unless repair is done by a qualified service technician.

1. Damaged On-Off

Switch/Cord.

2. Burned out motor, no power to motor or low voltage.

1. Replace damaged parts before using sander.

2. Consult Authorized Service

Center. Any attempt to repair this motor may create a hazard unless repair is done by a qualified service technician.

Sanding drum or belt slips or slows down easily

1. Applying too much pressure to workpiece.

2. Spindle knob too loose.

1. Reduce pressure on workpiece.

2. Tighten spindle knob.

1. Replace sandpaper.

Wood burns while sanding

1. Sanding drum is glazed with sap.

Sandpaper doesn’t remove material

Spindle doesn’t go through full 3/4” travel

1. Sandpaper is compacted with sawdust.

1. Sawdust is compacted under lower drum washer.

2. Fan not installed.

3. Damaged gearbox.

1. Replace sandpaper.

1. Vacuum sawdust from area of lower drum washer.

2. Ensure that fan is installed with vanes face down.

3. Consult Authorized Service

Center. Any attempt to repair this gearbox may create a hazard unless repair is done by a qualified service technician.

31

Repair Parts

Parts List For RIDGID Oscillating Edge Belt/Spindle Sander

Model EB44241

RIDGID parts are available on-line at www.ridgidparts.com

Figure 1

40

1

2, 44, 45

3, 46, 47, 48

4

43

39

6

5, 49, 50, 51

38

9

7

8

14

37

10

11

36

35

14

12

13

34

15

16

33

42

19

20

17

18

32

31

29

30

24

21

22

23

Ground Lead

26

41

25

19

27

28

32

Repair Parts

Parts List For RIDGID Oscillating Edge Belt/Spindle Sander

Model EB44241

RIDGID parts are available on-line at www.ridgidparts.com

Figure 1

Always order by Part Number—Not by Key Number

Key

No.

Part No.

Description

Key

No.

Part No.

Description

5

6

3

4

7

1

2

8

9

10

19

20

21

22

15

16

17

18

11

12

13

14

23

24

25

826358-1

805553-2

822304

See pg. 29

825808

See pg. 29

810993-2

825841

830291

805297-9

825523

825548

825844

825842

830246

825537

825852

159572-138

808380-7

825840

830456

159572-186

824604

830290

805549-22

Knob, Spindle

Washer

21/64 x 5/8 x 1/32

Drum, Sanding 3/4"

†Drum, Sandpaper

Plate, Throat 2"

†Belt, Sanding 4" x 24"

Screw, Set Half Dog

10/32 x 1/2

Adapter, Throat Plate

Fan

Screw, Flat Hd

1/4-20 x 5/8

Table, Rear

Plate, Wear

Nut, Special Twin 1/4-20

Screw, Shoulder 1/4-20

Chute, Sawdust

Bracket, Table Lock

Knob, 1/4-20 x 3/4

Screw, Wash/Hd

Ty “T” 10-32 x 3/8

Screw, Pan Hd 10-14 x 1/2

Spring, Detent

Base

Screw, Hex Hd

Ty “T” 1/4-20 x 1

Screw, Hex Wash/Hd

Ty “T” 8-32 x 3/8

• Motor/Drive Asm

Washer

13/64 x 3/8 x .031

26

27

28

29

826801

825854

819012

9416630

34

35

36

37

38

30

31

32

33

829785

AC1000

817399-11

37837

825549

825537-1

825543

825524

803309-2

39

40

41

42

43

825525

825539-1

SP6496

37836

—

44

45

805553-30

805553-24

46

47

48

49

50

51

822304-1

822304-2

822304-3

825808-1

825808-2

825808-3

Enclosure

Cord w/Plug

Foot

Screw, Hex Hd Ty “T”

5/16-18 x 1

Switch, Locking

†Key, Switch

Relay

Wrench, Hex “L” 5/32

Spacer, Table Lock

Bracket, Table Lock Left

Bolt, Table Lock

Table, Front

Screw, Soc Set Lock

10-32 x 3/8

Plate, Stop

Knob 1/4-20

Owners Manual

Wrench, Hex “L” 3/32

Belt Sanding Assembly

(See Fig. 2)

* Washer 5/8 x 1-3/4 x 1/8

Washer

21/64 x 7/8 x 3/64

Drum, Sanding 1"

Drum, Sanding 1-1/2"

Drum, Sanding 2"

Plate, Throat 1-1/2"

Plate, Throat 1"

Plate, Throat 1/2"

* Standard Hardware Item - May be purchased locally

† These parts are available where you purchased your sander.

• Any attempt to repair this motor may create a hazard unless repair is done by a qualified service technician. Repair service is available at your nearest Authorized Service Center.

33

Repair Parts

Parts List For RIDGID Oscillating Edge Belt/ Spindle Sander

Model EB44241

RIDGID parts are available on-line at www.ridgidparts.com

Figure 2

5 18

4

6

7

19 4

1

3 4

10

9

16

19

17

8

2

15

2

12

11

13

8

14

Always order by Part Number—Not by Key Number

Key

No.

Part No.

Description

Key

No.

Part No.

Description

4

5

6

7

8

1

2

3

9

10

11

825539

830306

830453

37482

830305

825531

825529

805549-4

830304

826163-2

830454

Knob 10-32 x 1-1/4

Washer 12 mm 1.0.

Drum/Drive Asm.

Nut, Lock

Guide

Spring, Extension

Lever

* Washer

13/64 x 1/2 x 3/64

Shaft, Idle

Cap, Grip

Drum, Idle Asm

* Standard Hardware Item - May be purchased locally

12

13

14

15

16

17

18

19

817453

826802

30521

821166-1

809169-9

820175

9416712

114603

Ring, Retaining 5160-50

Platen

Spring, Swivel

Screw, Flat Hd Hex

10/32 x 1-1/2

Screw, Pan Cr Ty T

8-32 x 3/4

Washer, Rubber

* Washer

3/16 x 5/8 x 1/16

* Lockwasher, Ext. #10

34

Notes

35

© 2003 RIDGID,INC.

Part No. SP6496

RIDGID® HAND HELD AND STATIONARY POWER TOOL

LIMITED THREE YEAR WARRANTY AND

90 DAY SATISFACTION GUARANTEE POLICY

This product is manufactured under license from Ridgid, Inc. by One World

Technologies, Inc.. All warranty communications should be directed to One

World Technologies, Inc. at (toll free) 1-866-539-1710.

90-Day Satisfaction GuaranteePolicy

During the first 90 days after the date of purchase, if you are dissatisfied with the performance of this Ridgid® tool for any reason, you may return the tool to the dealer from which it was purchased for a full refund or exchange. To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product.

The replacement tool will be covered by the limited warranty for the balance of the three year warranty period.

What is covered under the Limited Three Year Warranty

This warranty covers all defects in workmanship or materials in this

RIDGID® tool for the three year period from the date of purchase. This warranty is specific to this tool. Warranties for other RIDGID® products may vary.

How to obtain service

To obtain service for this RIDGID® tool you must return it, freight prepaid, to an authorized RIDGID® service center for hand held and stationary power tools. You may obtain the location of the authorized service center nearest you by calling (toll free) 1-866-539-1710 or by logging on to the RIDGID® website at www.ridgidwoodworking.com. When requesting warranty service, you must present the proof of purchase documentation, which includes a date of purchase. The authorized service center will repair any faulty workmanship, and either repair or replace any defective part, at our optioon at no charge to you.

What is not covered

This warranty applies only to the original purchaser at retail and may not be transferred. This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by other than authorized

RIDGID® service center for hand held and stationary power tools. One

World Technoligies, Inc. makes no warranties, representations or promises as to the quality or performance of its power tools other than those specifically stated in this warranty.

Additional Limitations

To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-

POSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to three years from the date of purchase. One

World Technologies, Inc. is not responsible for direct, indirect, incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Catalog No. EB4424

Model No. EB44241 Serial No. ________

The model and serial numbers may be found on the back side of the base. You should record both model and serial number in a safe place for future use.

QUESTIONS OR COMMENTS?

CALL 1-866-539-1710

www.ridgidwoodworking.com

Please have your Model Number and Serial

Number on hand when calling.

Form No. SP6496 Printed in Taiwan 4/03