Zenith Installation Configuration and Connections
SYSTEM 4
xi
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: ZENITH
Included Communications Adapter(s):
Quantity Part Number
1 26-471-01
Description
ADP, UNV, “C”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “ ✔ ” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
ZENITH PRO
CONFIG
AS
MODEL
✔ Zenith Pro
SW1
1 2 3 4
SW2 SW3 SW4 SW5 SW6 PROJ COMM
CABLE ADAPTER off on off on 0 0 E 0 0 J15 26-471-01
Extron • System 4 xi Switcher Series • User’s Manual • P/N 68-419-02 Rev. A
Zenith Installation Configuration and Connections
Connecting System 4
xi
to Zenith Pro Projector
If the System 4 xi is already configured for a Zenith Pro projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the
System 4 xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4 xi is already set up for the Zenith projector. Apply power to the System 4 xi and do the following: a. Press to display the M
ENU
S
ELECT
on the LCD screen.
b. Press or to step to Menu 8.
[System 4 xi model and software version displayed here]
(See note.)
(See note.)
(See note.)
(See note.)
(Note: Information depends on
System 4 xi setup.)
} c. Press to select this menu.
d. Press or to display the configuration. The example to the left is general, yours will show the System 4 xi model name, the software version and the following information:
PRJ = ZENITH
PRJ BAUD = 9600
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the System 4 xi User’s Manual to remove the
System 4 xi cover. Then go to page 2-4 and refer to the configuration below to set up the Main Controller board. Continue with Step 3 (below) when the configuration is correct.
Config as
Projector
✔ Zenith Pro
SW1: 1-2-3-4 SW2 SW3 SW4 SW5 SW6 Prj Cable Comm
Adapter off-on-off-on 0 0 E 0 0 J15 26-471-01
SW3 SW5
SW2
J15
SW4
4
SW1
3 2 1
ON
3. Double-check your work and be sure the System 4 xi
cover is on securely.
4. Install the System 4 xi
in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is removed at the AC cord, and then restored.
Refer to the following connection diagram and continue.
5. The Zenith Comm Adapter (26-471-01) has a 9-pin male connector that accommodates the Comm Extension cable. The other end of the Comm Adapter plugs into the projector’s 25-pin “Remote 1” port.
Extron • System 4 xi Switcher Series • User’s Manual • P/N 68-419-02 Rev. A Page 1
Zenith Installation Configuration and Connections
6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4 xi .
______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4 xi
output and those on the other end onto the matching
BNCs on the Zenith Pro connector panel.
System 4xi Series – Zenith Pro Projector Connections
Use the illustration below as a guide when connecting the System 4 xi
to a Zenith
Pro projector. Refer to Zenith documentation to continue the installation.
In
Video
Out
Y/C IN
Y C
S-Video
In
Remote 1 System Bus
In Out
Remote 2
R G/G Sync B H/Sync
RGB 1 IN
V R/Pr G/Y B/Pb H/Sync
RGB 2 IN
V
25-Pin
"C"
Adapter
TO COM
26-471-01
"C"
CC 50'
3, 4 or 5 BNC
15-Pin
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
System 4 xi
. See page 2-5 for cabling guidelines.
Extron • System 4 xi Switcher Series • User’s Manual • P/N 68-419-02 Rev. A Page 2
