DOREL ASIA

Model No:

DA6790 (GREY)

UPC CODE:

0-65857-16721-4

CRIB CHANGER COMBO

2 IN 1 CRIB

NOTE:

THIS INSTRUCTION BOOKLET

CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND

KEEP FOR FUTURE REFERENCE.

Lot number:

(TAKEN FROM CARTON)

_____________________________________

Date of purchase:

_______ / _______ / _______

DO NOT RETURN PRODUCT TO THE STORE.

If a part is missing or damaged, contact our customer service department. We will replace the part FREE of charge.

DO NOT RETURN PRODUCT TO STORE

E-MAIL:[email protected]

CUSTOMER SERVICE

If you are missing parts or have any questions about this product, contact our customer service representative first!

CALL 1-800-295-1980

You can also order parts by writing to the address listed below. Please include the product model number, color and a detailed description of the part.

Customer Service Department No. 413

12345 Albert-Hudon Boulevard, Suite 100

Montreal, Quebec

Canada, H1G 3L1

E-MAIL: [email protected]

Convertible Crib

WARNING

* Failure to follow these warnings and assembly instructions could result in serious injury or death.

* Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.

* Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts or sharp edges before assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or broken. Contact a customer service representative at 1-800-295-1980 for replacement parts and instructional literature if needed. DO NOT substitute parts.

* Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an infant.

* Stop using the crib when child begins to climb out or reaches the height of 35 inches (89 cm).

* To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.

* DO NOT place crib near window where cords from blinds or drapes may strangle a child.

* Strings can cause strangulation! DO NOT place items with a string around a child's neck, such as hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.

* To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.

* If refinishing, use a non-toxic finish specified for children's products.

* When child is able to pull to standing position, set mattress to lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out.

* Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.

* Replace teething rail if damaged or loose (if teething rail is provided for this model).

* CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY 51-5/8 INCHES (69CM BY

131CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).

* Infants can suffocate in gaps between crib sides and a mattress that is too small.

* Follow warnings on all products in a crib.

* INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT. Openings in and between bed parts can entrap head and neck of a small child.

* NEVER use bed with children under 15 months or over 50 lbs.

* ALWAYS follow assembly instructions.

* STRANGUALTION HAZARD. NEVER place bed near windows where cords from blinds or drapes may strangle a child.

* NEVER suspend strings over a bed.

*

NEVER place items with a string, cord, or ribbon around a child's neck, such as hood strings or pacifier cords. These items can catch on bed parts.

* CAUTION

ENTRAPMENT HAZARD. To avoid dangerous gaps, any mattress used on this bed shall be a full-size crib mattress at least 51-5/8 inches (1310 mm) in length, 27-1/4 inches (690 mm) in width, and a max thickness of 6 inches (150 mm).

*

*

Changing Table

WARNING

FALL HAZARD - To prevent death or serious injury, always keep child within arm's reach.

Avoid serious injury. Never leave child unattended.

*

*

Read all instructions before use of the changing table. KEEP INSTRUCTIONS FOR FUTURE USE.

DO NOT use the changing table if it is damaged or broken.

*

* When used as a changing table, this unit must be used with a changing pad (not provided) equipped with safety straps that secure the child to the changing pad as well as straps that secure the pad to the changing table.

*

The changing table is to be used with a changing pad measuring 16 inches X 32 inches and not exceeding 2 inches in thickness (excluding the height of any contoured edges).

* The maximum recommended weight of the child is 30 lbs (13.60 kgs).

NOTES

* Ensure all parts and components are present before beginning assembly.

* Assemble on a soft, smooth surface to prevent damage to product finish.

* DO NOT use power tools.

* CAUTION: Adult assembly required.

* Assembly will require two people.

* Estimated assembly time: 60 minutes.

CARE AND CLEANING

Dust regularly with a soft, lint-free cloth to prevent soil build-up. A damp cloth may be used occasionally to clean surface. Dry immediately. Do not use any abrasives that may damage finish.

Excessive exposure to sunlight and extreme changes in temperature and moisture can damage wood furniture.

MAINTENANCE

Check bolts/screws periodically and tighten them if necessary.

LIMITED WARRANTY

Dorel Asia warrants its product to be free from defects in material and workmanship and agrees to remedy any such defect. This warranty covers 1 year from the date of original purchase. This warranty is valid only upon presentation of proof of purchase. This is solely limited to the repair or replacement of defective furniture components and no assembly labor is included. This warranty does not apply to any product which has been improperly assembled, subjected to misuse or abuse or which has been altered or repaired in any way. This warranty gives you specific legal rights and you may also have other rights which vary from State to State.

WARNING: Should this product become damaged, and/or components are broken or missing, DO NOT USE.

CRIB CHANGER COMBO

DA6790

HARDWARE LIST

1 2

3

Ø1/4" X 13mm X 75mm

BOLT

8 PCS

5

Ø1/4" X 13mm X 55mm

BOLT

10 PCS

7

Ø1/4" X 13mm X 15mm

MATTRESS SUPPORT BOLT

16 PCS

4

Ø1/4" X 13mm X 60mm

BOLT

2 PCS

Ø8mm X 30mm

WOOD DOWEL

14 PCS

6

Ø1/4" X 13mm X Ø10mm

BARREL NUT

8 PCS

ALLEN KEY

1 PC

PARTS LIST

A B

CRIB CHANGER COMBO

DA6790

C D

E

LEFT SIDE PANEL

1 PC

RIGHT SIDE PANEL

1 PC

F G

BACK PANEL

1 PC

H

FRONT PANEL

1 PC

I

FRONT RAIL

1 PC

MATTRESS SUPPORT

1 PC

J

RIGHT SIDE FRAME

1 PC

K L

TOP BACK RAIL

1 PC

MIDDLE BACK RAIL

1 PC

M

BOTTOM BACK RAIL

1 PC

N

TOP FRONT RAIL

1 PC

MIDDLE FRONT RAIL

1 PC

BOTTOM FRONT RAIL

1 PC

CHANGER'S PANEL

3 PCS

CRIB CHANGER COMBO

DA6790

CRIB ASSEMBLY INSTRUCTION

NOTE: When inserting bolts, turn clockwise until tight. Then loosen

1/2 - 3/4 of a turn. After crib is completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly.

CRIB CHANGER COMBO

DA6790

STEP 1

Insert barrel nuts (6) into back panel (C ) as shown.

Attach left side panel (A)and right side panel (B) to back panel (C) with bolts (1).

Use Allen Key (7) to tighten all bolts (1).

1 6

CRIB CHANGER COMBO

DA6790

STEP 2

Attach mattress support (F) to the posts with mattress support bolts (5).

Use Allen Key (7) to tighten the mattress support bolts (5).

5

INCORRECT-

Raised edge should face down -this photo shows mattress support is

INCORRECT-

Tabs on corners of mattress support should point up.



CORRECT

* Tabs to point UP.

* Flat surface of mattress support to face up mattress must sit on flat surface.

NOTE: The above photos and drawings showing how to properly attach the mattress support are for reference only. Crib styles and colors will vary.

CRIB CHANGER COMBO

DA6790

STEP 3

Insert wood dowels (4) into left side panel (A) and right side panel (B).

insert barrel nuts (6) into front rail € as shown.

Attach front rail (E) to left side panel (A) and right side panel (B) with bolts (1).

Use Allen Key (7) to tighten all bolts (1).

1 4 6

CRIB CHANGER COMBO

DA6790

STEP 4

Insert barrel nuts (6) into front panel (D) as shown.

Attach front panel (D) to left side panel (A) and right side panel (B) with bolts (1 and 3) as shown.

Secure front panel (D) to front rail (E) with bolts (2).

Use Allen Key (7) to tighten all bolts (1, 2 & 3).

6

3 1

2

CRIB CHANGER COMBO

DA6790

STEP 5

Attach top back rail (H) and top front rail (K) to right side panel (B) with bolts (3).

Insert wood dowels (4) into middle back rail (I) and middle front rail (L) and attach them to right side panel (B).

Insert wood dowel (4) into bottom back rail (J). Secure bottom back rail (J) to right side frame

(B) using bolts (3).

Attach bottom front rail (M) to right side panel (B) with bolt (3).

Use Allen Key (7) to tighten all bolts (3).

3 4

CRIB CHANGER COMBO

DA6790

STEP 6

Slide changer panels (N) into the grooves of rails as shown below.

Make sure changer panels (N) rest inside the grooves of right side panel (B).

CRIB CHANGER COMBO

DA6790

STEP 7

Insert wood dowels (4) into top back rail (H), middle back rail (I), top front rail (K), and middle front rail (L).

Attach right side frame (G) to the assembled unit with bolts (3).

Use Allen Key (7) to tighten all bolts.

3 4

CRIB CHANGER COMBO

DA6790

WARNINGS:

* CAUTION- ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY

51-5/8 INCHES (69CM BY 131CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).

* The day bed is not intended for children under 15 months of age or over 50 lbs (22.7 kgs).

DAY BED ASSEMBLY INSTRUCTION: STARTING FROM CRIB

STEP1: Follow steps backward from 7 to 5 to remove changer with Allen Key (7).

STEP 2: Unscrew the bolts (2) underneath the crib front rail (E) with Allen Key (7).

STEP 3: Detach the front panel (D) from left/right side panel (A & B) with Allen Key (7).

STEP 3: If mattress support (F) is not in the lowest position, unscrew bolts (5) from left/right

panel (A & B) and move to the lowest position.

STEP 4: Ensure all bolts are tightly secured.

CRIB CHANGER COMBO

DA6790

CAUTION: This unit is intended for use only with the products and/or maximum weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury.

NOTE:

DO NOT throw away this instruction manual. Use the crib pouch attached to the mattress support to store this manual for future use.

The maximum recommended weight of the child is 30 lbs (13.60 kgs).

Maximum weighty per shelf 10 lbs

Stop using crib when child begins to climb out or reaches the height of

35 inches (89 cm).

That's it ! You've finished assembling your crib changer combo!

DO NOT RETURN PRODUCT TO THE STORE.

If a part is missing or damaged, contact our customer service department. We will replace the part FREE of charge.

DO NOT RETURN PRODUCT TO STORE

E-MAIL:[email protected]

MODEL #: DA6790

Customer Service

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE

PLEASE CONTACT CUSTOMER SERVICE REPRESENTATIVES AT THE FOLLOWING

NUMBERS SHOULD THERE BE ANY MISSING OR DEFECTIVE PART(S).

Customer Service Phone Number 1-800-295-1980

Customer Service Fax Number 514-353-7819

Email: [email protected]

Request Date:

Name:

Shipping Address:

Street & Number:

City & State:

Zip Code:

Day Time Phone Number:

(including area code)

Date & Place of Purchase:

Part(s) description and quantity: (Please be sure to list model number or SKN number)

Customer Service Representative Mailing Address:

Customer Service Department No. 413, 12345 Albert-Hudon Boulevard, Suite 100, Montreal, QC, Canada, H1G 3L1