Online access continued

Edit a Current Schedule

You also have the option to go back and edit your previously programmed schedules (e.g., change settings, times, or even copy entire schedules).

1. On the left side, under thermostat, click on your serial number to see the drop-down menu. If you have more than one thermostat installed, all of the serial numbers will be listed. Each one can be programmed individually.

2. Click on SCHEDulES in the drop-down menu. The last Schedule

Sent from the web interface will appear at the top of your screen.

3. Click on EDit below the schedule you want to change

(e.g., your last Schedule Sent).

4. Follow Steps 2-5 from Create a new Schedule for each thermostat schedule.

manual Program

The web interface also enables you to temporarily change your thermostat settings without losing any pre-programmed schedules.

1. On the left side, under thermostat, click on your serial number to see the drop-down menu. If you have more than one thermostat installed, all of the serial numbers will be listed.

Each one can be programmed individually.

2. Click on manual in the drop-down menu.

3. You have two Hold options: a. Temporary Hold - Press or to select the new temperature you want until the next pre-programmed change in your schedule. This creates a temporary Hold, which will appear on your thermostat screen after the signal is received.

b. Permanent Hold - Press or to select the new temperature you want. Click on HOlD to maintain this temperature. This creates a Permanent Hold until you click

Run PROGRam, which will cancel the Permanent Hold setting and return to your pre-programmed schedule.

5. Adjust mODE and Fan settings.

6. Click on SEnD to send these settings to the thermostat.

Allow approximately five minutes for the thermostat to receive these settings.

7. To return to your pre-programmed schedule, click on

Run PROGRam.

NOTE: The web interface is a one-way communication feature and does not display current settings or temperatures at the thermostat, only the settings last sent through the interface (i.e., thermostat settings will not match Last Schedule Sent if someone has manually changed the settings on the thermostat itself).

Opting Out of a Cycling Event

You may choose to not participate in a cycling event once per month.

To opt out on a certain date, you may call the WattSaver hotline or access the WattSaver website.

1. On the left side, under Programs click OPt Out.

2. Type or select the date you wish to opt out.

3. Click Submit.

Your opt-out date will appear on the Home page.

View Cycling History

You may see when Westar Energy has cycled your air conditioner(s) since installation of the thermostat(s).

1. On the left side, under Programs select CyClinG HiStORy.

This will display the current day’s cycling data, if applicable.

2. Click ViEW COmPlEtE HiStORy to see all the cycling data since installation.

The partnership where helping you save money helps all of us save energy.

Thank you for joining.

WattSaver

®

is part of

Westar Energy’s portfolio of programs designed to help you save energy, save money and improve the environment.

Westar Energy offers residential and commercial customers a variety of energy saving programs. To learn more, please visit www.WestarEnergy.com/Efficiency.

©2011 Westar Energy. All Rights Reserved.

Printed on recycled paper

WattSaver Quick

Reference Guide

Our installer programmed your thermostat with your preferred settings. This Quick Reference Guide makes it easy for you to program your thermostat.

By participating in this program, you are helping to manage energy use in our region. This partnership with Westar Energy will also help delay the need for additional power plants and preserve the environment for future generations.

WattSaver hotline 1-888-753-6523

Our Customer Service Representatives can also guide you through programming your thermostat and answer any questions you may have about the program.

For more information about WattSaver, please visit our website at www.WestarEnergy.com/WattSaver

thermostat Settings

Setting Current time and Day

The clock should never require adjustment since it automatically updates for daylight-saving time and stores all date/time information.

Should the time and date need to be reset after a power failure, this is an indication that the battery needs to be replaced. To manually set the current time display:

1. Press ClOCK, then press or to adjust the time.

(Press and hold or to advance the time more quickly.)

2. Press DOnE to save and exit (or press CanCEl to exit without changing the time).

Programming or Changing Settings for

Heating and Cooling

There are five (5) system modes.

Press the SyStEm button to select one of the following, then press DOnE. Pressing the

SyStEm button successively will toggle the thermostat from one mode to the next.

• HEat: Thermostat controls only the heating system.

• COOl: Thermostat controls only the cooling system.

• OFF: Heating and cooling systems are off.

• autO: Thermostat automatically selects heating or cooling depending on the indoor temperature.

• Em HEat (only for heat pumps with auxiliary heat):

Thermostat controls emergency and auxiliary heat.

It’s easy to program your system for maximum energy savings.

You can program four time periods with different settings. Times can be programmed in 15-minute increments.

1. Press SCHED, then press EDit.

2. Press day buttons to select day(s).

3. Press or to set WaKE time for selected day(s).

4. Press or to set HEat and COOl temperature for this time period.

5. Press other time periods (lEaVE, REtuRn, SlEEP) to set time and temperatures for each.

6. Press DOnE to save and exit (or press CanCEl to exit without saving changes).

NOTE: You can press CANCEL PERIOD to eliminate any unwanted time period.

Changing your Fan Control

Press Fan to select fan operation, then press DOnE.

• On: Fan is always on.

• autO: Fan runs only when the heating or cooling system is on.

• CiRC: Fan runs randomly, about 35% of the time, not counting any run time with the heating or cooling system.

You can press Fan to override the fan settings you have programmed for different time periods. If you select On or CiRC, the setting you select remains active until you press Fan again to select autO.

temporary Setting Changes

The thermostat enables you to temporarily change your settings without losing any pre-programmed schedules.

Press or to immediately adjust the temperature. This temporarily overrides the temperature setting for the current time period.

The new temperature is maintained only until the next pre-programmed time begins. For example, if you want to turn up the heat early in the morning, it will automatically be adjusted later, according to the preprogrammed schedule.

To cancel the temporary setting at any time, press CanCEl or SCHED.

The pre-programmed schedule resumes.

Permanent Setting Changes

The thermostat enables you to temporarily change your settings without losing any pre-programmed schedules.

Press or to immediately adjust the temperature. This temporarily overrides the temperature setting for the current time period and when followed by pressing HOlD, permanently adjusts the temperature.

Pressing HOlD turns off the program schedule, but the program settings are retained and can be resumed by pressing CanCEl or SCHED to cancel HOlD and reactivate the pre-programmed schedule.

Clean the Screen

1. Press SCREEn to go to the cleaning screen.

2. Press OK to lock the screen for cleaning. The screen remains locked for 30 seconds so you can clean the screen without changing any settings.

3. Do not spray any liquid directly on the thermostat. Spray liquids onto a cloth, then use the damp cloth to clean the screen. Use water or household glass cleaner. Avoid abrasive cleansers.

4. After 30 seconds, press CanCEl to resume normal operation, or press OK if you require more time for cleaning.

Online access

Program your thermostat Online

To begin, go to: www.wattsaverprogram.com. The first screen you will see is the login screen.

user iD and Passwords

The default user iD is your Westar Energy account number. The

default Password is the serial number for your thermostat. That number can be found on the work order the installer left at the time of installation or on the bottom of the thermostat. Please allow up to

4 hours after your thermostat is installed for us to have your information accessible online.

To reset your user iD and Password after your initial login, click on

CHanGE lOGin at the bottom left of the screen. WattSaver personnel do not have access to your user iD and Password once it has been changed. For future reference, record your user iD and

Password in the following space: user iD Password

Change thermostat Settings

1. On the left side, under thermostat, click on your serial number to see the drop-down menu. If you have more than one thermostat installed, all of the serial numbers will be listed. Each one can be programmed individually.

2. Click on SCHEDulES in the drop-down menu. The last Schedule

Sent from the web interface will appear at the top of your screen.

Create a new Schedule

1. Click on CREatE.

2. Select one of the scheduling options. Then click on nEXt.

3. Click in the name field, and type the name you wish to use for the schedule (e.g., Normal or Vacation).

4. Enter your desired time and temperature settings underneath

WaKE, lEaVE, REtuRn and SlEEP by typing or using the slide bar.

You may also use your mouse or keyboard’s tab button to advance to the next field. Repeat this process until all fields are programmed to your desired settings. When complete, click on SaVE, and your schedule will appear on the thermostat-Schedules screen under the name you assigned in step 3.

5. If you want the schedule to take effect immediately, click on SEnD

nOW. Allow approximately five minutes for the thermostat to receive the new schedule.

NOTE: The web interface is a one-way communication feature and does not display current settings or temperatures at the thermostat, only the settings last sent through the interface

(i.e., thermostat settings will not match Last Schedule Sent if someone has manually changed the settings on the thermostat itself).

Online Access continued on back.