Activity Tunnel

Please keep this instruction sheet for future reference, as it contains important information.

Requires three “AA” (LR14) alkaline batteries

(not included).

Adult assembly is required.

Tool required for assembly:

Phillips screwdriver

(not included).

H5703

Instructions

™

www.fisher-price.com

CAUTION

This toy contains small parts in its unassembled state.

Adult assembly is required.

Parts

Care

• Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not immerse this toy.

• This toy has no consumer serviceable parts. Do not take this toy apart.

Consumer Information

Questions? We'd like to hear from you!

Call Fisher-Price ® Consumer Relations, toll-free at 1-800-432-5437,

8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470.

Or, visit us on line at www.service.mattel.com.

Write to us at: Fisher-Price ® Consumer Relations, 636 Girard Avenue,

East Aurora, New York 14052.

Tunnel Top

4 Legs

FCC Note (United States Only)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

2 Side Rails

Not Shown: 3 Hanging Toys

Screws Shown Actual Size

#6 x 2" Screw – 4

#6 x 3 /

8

" Screw – 4

Note: Tighten or loosen all screws with a Phillips screwdriver.

Do not over-tighten the screws.

For countries outside the United States:

CANADA: Questions? 1-800-432-5437.

Mattel Canada Inc., 6155 Freemont Blvd.,

Mississauga, Ontario L5R 3W2; www.service.mattel.com.

GREAT BRITAIN : Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.

Helpline: 01628 500302.

AUSTRALIA : Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,

Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.

NEW ZEALAND : 16-18 William Pickering Drive, Albany 1331, Auckland.

ASIA : Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City,

Tsimshatsui, HK, China.

Tunnel Top

Assembly

1 1

Socket

Connector

• Locate the two legs with sockets in the top.

• Locate the two connector wires coming from the tunnel top.

• Insert and “snap” each connector into the matching socket, as shown.

2 1

• Turn the assembly around and insert two 2" screws through the tunnel top and into each leg, as shown. Tighten the screws.

• Fully insert the two legs into the openings in the tunnel top.

• Fully insert the other two legs into the openings in the tunnel top.

Hint: The legs will only fit one way.

Assembly

7 1

• Turn the assembly around again and insert two 2" screws through the tunnel top and into each leg, as shown. Tighten the screws.

• Grasp both ends of the tunnel top and press to “snap” the ends of the side rails into place, as shown.

Side Rail

• Fit the smaller end of one side rail into the hole in the tunnel.

• Push the side rail so that it slides through the fabric tube in the tunnel and emerges at the other end.

• Repeat this procedure to insert the other side rail.

• Insert two 3 /

8

" screws into the holes in the end of each side rail.

Tighten the screws.

Assembly

Tab

Battery Installation

1.5V x 3

"AA" (LR6)

Shown Actual Size

Battery Compartment Door

• Insert and “snap” each of the eight tabs on the mesh into the matching slots in the legs to secure the mesh.

Bottom View

For best performance, we recommend replacing the batteries that came with this toy with three, new alkaline “AA”

(LR6) batteries.

• Locate the battery compartment on the bottom of one leg.

• Loosen the screws in the battery compartment door with a

Phillips screwdriver. Remove the battery compartment door.

• Insert three “AA” (LR6) alkaline batteries, as indicated inside the battery compartment.

Hint: We recommend using alkaline batteries for longer life.

• Replace the battery compartment door and tighten the screws with a Phillips screwdriver. Do not over-tighten.

• When lights or sounds from this toy become faint or stop, it’s time for an adult to change the batteries!

Battery Safety Information

Batteries may leak fluids that can cause a chemical burn injury or ruin your toy. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.

• Remove batteries during long periods of non-use. Always remove exhausted batteries from the toy. Dispose of batteries safely. Do not dispose of batteries in a fire. The batteries may explode or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or equivalent type, as recommended.

• Do not charge non-rechargeable batteries.

• Remove rechargeable batteries from the toy before charging.

• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.

Fun Music Lights and Activities!

Power/Volume

Switch

Action Button

• Locate the volume switch on the top of the toy.

• Slide the switch to the desired position: on with low volume ; on with high volume ; or Off .

• A sensor in the tunnel also knows when baby crawls through and activates dancing lights and lively music.

• Press the action button on the top of the tunnel for fun lights and music.

Note: After a few minutes of inactivity, the tunnel “goes to sleep.”

To “wake up” the tunnel, simply press the action button again.

Fit the three hanging toys into any of the slots around the tunnel.

Hint: When baby is ready to crawl, move the toys to the back of the tunnel to encourage baby to crawl through!

Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.

©2005 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.

PRINTED IN CHINA

H5703pr-0920