The content published in this document is believed to be accurate. Identive does not, however, provide any representation or warranty regarding the accuracy or completeness of its content and regarding the consequences of the use of information contained herein. If this document has the status “Draft”, its content is still under internal review and yet to be formally validated.

Identive reserves the right to change the content of this document without prior notice. The content of this document supersedes the content of previous versions of the same document.

The document may contain application descriptions and/or source code examples, which are for illustrative purposes only. Identive gives no representation or warranty that such descriptions or examples are suitable for the application that the reader may want to use them for.

Should you notice problems with the provided documentation, please provide your feedback to [email protected]

1.2. Licenses

If the document contains source code examples, they are provided for illustrative purposes only and subject to the following restrictions:



You MAY at your own risk use or modify the source code provided in the document in applications you may develop. You MAY distribute those applications ONLY in form of compiled applications.



You MAY NOT copy or distribute parts of or the entire source code without prior written consent from Identive.



You MAY NOT combine or distribute the source code provided with Open Source

Software or with software developed using Open Source Software in a manner that subjects the source code or any portion thereof to any license obligations of such

Open Source Software.

If the document contains technical drawings related to Identive products, they are provided for documentation purposes only. Identive does not grant you any license to its designs.

1.3. Trademarks

MIFARE

is a registered trademark of NXP Semiconductors BV.

Windows is a trademark of Microsoft Corporation.

CLOUD 45

0 F R

EFERENCE

ANUAL

2. Introduction to the manual

2.1. Objective of the manual

This manual provides an overview of the hardware and software features of the CLOUD 45x0 F dual interface smart card reader modules (CLOUD 4500 F and CLOUD 4510 F).

This manual describes in detail interfaces and supported commands available for developers using CLOUD45x0 F in their applications.

The reader will additionally find in this document important component location to help with the design of custom external housing.

2.2. Target audience

This document describes the technical implementation of CLOUD 45x0 F.

The manual targets software developers. It assumes knowledge about ISO 7816, 13.56 MHz contactless technologies like ISO/IEC 14443 and commonly used engineering terms.

Should you have questions, you may send them to [email protected]

2.3. Product version corresponding to the manual

Item Version

Hardware 0.3

Firmware 1.00

CLOUD 45

0 F R

EFERENCE

ANUAL

2.4. Definition of various terms and acronyms

Term Expansion

APDU

ATR

ATS

Byte

CCID

CID

DFU

LED

MIFARE

NAD

Nibble

PCD

PC/SC

PICC

PID

Proximity

PUPI

RFU

USB

VID

(xyz)b

0xYY

Application Protocol Data Unit

Answer to Reset, defined in ISO7816

Answer to select, defined in ISO/IEC 14443

Group of 8 bits

Chip Card Interface Device

Card Identifier

Device Firmware Upgrade

Divider receive: used to determine the baud rate between the reader to the card

Divider send: used to determine the baud rate between the card to the reader

Light emitting diode

The ISO14443 Type A with extensions for security (NXP)

Not applicable

Node Address

Group of 4 bits. 1 digit of the hexadecimal representation of a byte.

Example: 0xA3 is represented in binary as (10100011)b. The least significant nibble is

0x3 or (0011)b and the most significant nibble is 0xA or (1010)b

Proximity Coupling Device

Personal Computer/Smart Card: software interface to communicate between a PC and a smart card

Proximity Integrated Chip Card

Product ID

Distance coverage till ~10 cm.

Pseudo unique PICC identifier

Radio Frequency

Reserved for future use

Universal Serial Bus

Vendor ID

Binary notation of a number x, y, z



0,1



The byte value YY is represented in hexadecimal

CLOUD 45

0 F R

EFERENCE

ANUAL

2.5. References

Doc ref in the manual

Description

ISO/IEC 7816-3

ISO/IEC 7816-4

Identification cards

— Integrated circuit cards

—Part 3:Cards with contacts — Electrical interface and transmission protocols

Identification cards - Integrated circuit(s) cards with contacts

Part 4: Interindustry commands for interchange

ISO/IEC 14443-3

ISO/IEC 7816-4: 1995 (E)

Identification cards

— Contactless integrated circuit(s) cards

— Proximity cards

—Part 3:Initialization and anticollision

ISO/IEC 14443-4 Identification cards

— Contactless integrated circuit(s) cards

— Proximity cards

Part 4: Transmission protocol ISO/IEC 14443-

4:2001(E)

PC/SC

PCSC3

PCSC3-AMD1

PCSC3-SUP

PCSC3-SUP2

CCID

USB

AN337

AN338

Interoperability Specification for ICCs and Personal

Computer Systems v2.01

Interoperability Specification for ICCs and Personal

Computer Systems

Part 3. Requirements for PC-Connected Interface

Devices

Interoperability Specification for ICCs and Personal

Computer Systems

Part 3. Requirements for PC-Connected Interface

Devices

– Amendment 1

Interoperability Specification for ICCs and Personal

Computer Systems

Part 3. Supplemental Document

Interoperability Specification for ICCs and Personal

Computer Systems

Part 3. Supplemental Document for Contactless

ICCs

Specification for Integrated Circuit(s) Cards

Interface Devices 1.1

Universal Serial Bus Specification 2.0

Application Note describing handling of DESFire

EV1 cards

Application Note describing handling of MIFARE

Plus cards

Issuer

ISO / IEC

PC/SC Workgroup

USB-IF

Identive

CLOUD 45

0 F R

EFERENCE

ANUAL

2.6. Conventions

Bits are represented by lower case ‘b’ where followed by a numbering digit.

Bytes are represented by upper case ‘B’ where followed by a numbering digit.

Bit number 5 Bit number 0 b7 b6 b5 b4 b3 b2 b1

Most significant nibble Least significant nibble

1 Byte = 8 bits = 2 nibbles

Byte number 2 b0

B0 B1 B2 B3 B4 B5 B6 B7

Byte number 11

B8 B9 B10 B11

String of 12 bytes

Example:

163 decimal number is represented

 in hexadecimal as 0xA3

 in binary as (10100011)b

The least significant nibble of 0xA3 is



0x3 in hexadecimal



(0011)b in binary

The most significant nibble of =xA3 is



0xA in hexadecimal



(1010)b in binary

CLOUD 45

0 F R

EFERENCE

ANUAL

3. General information about CLOUD 45x0 F

3.1. CLOUD 45x0 F key benefits

With its state of the art feature set, CLOUD 4500 F is the perfect reader choice for environments where both contact and contactless smart card support is required while CLOUD

4510 F perfectly fits environments where access to contactless cards with simultaneous access to a contact SAM card is required.

As for all Identive products, CLOUD 45x0 F is designed to offer best in class interoperability.

3.2. CLOUD 45x0 F key features



13.56MHz contactless reader: o ISO14443 type A & B, o MIFARE



ISO7816 compliant contact smart card reader for ID-1 cards (CLOUD 4500 F)



ISO7816 compliant contact smart card reader for ID-000 cards (CLOUD 4510 F)



PC/SC v2.0 compliant



Full CCID for both the contact and the contactless interfaces



Secure in-field SmartOS

TM firmware upgrade



Unique reader serial number which enables that CLOUD 45x0 F can be plugged into any USB slot on a PC without having to re-install the driver. Additionally, the application S/W running on the host can check for exact readers



249 bytes of non-volatile user memory



NFC P2P (passive mode) capable



Secure key loading support for MIFARE Classic cards



Communication speed up to 848Kbps

CLOUD 45

0 F R

EFERENCE

ANUAL

3.3. CLOUD 45x0 F ordering information

Item Part number

CLOUD 4500 F 905322

CLOUD 4510 F 905323

3.4. CLOUD 45x0 F customization options

Upon request and based on a minimum order quantity, Identive can consider customizing:



The product label



The USB strings

Terms and conditions apply, please contact your local Identive representative or send an email to [email protected]

CLOUD 45

0 F R

EFERENCE

ANUAL

3.5. Contactless communication principles and CLOUD

45x0 F usage recommendations

CLOUD 45x0 F is a dual interface reader module capable of reading both contact smart cards and contactless user tokens. The following paragraph focuses on a few specifics of contactless communication to outline usage recommendations in order to ensure best user experience.

CLOUD 45x0 F is a contactless reader

designed to communicate with user credentials.

User credentials

are made of a contactless integrated circuit chip connected to an antenna

User credentials can take several form factors:



Credit card sized smart card



Key fob



USB token



NFC mobile phone etc…

Communication between CLOUD 45x0 F and user credentials uses magnetic field inductive coupling.

The magnetic field generated by CLOUD 45x0 F has a carrier frequency of 13.56MHz.

5 x0

CLOUD 45x0 F

User tokens

3.5.1. Power supply

When the user credential is put in the magnetic field of the reader, its antenna couples with the reader and an induction current appears in the antenna thus providing power to the integrated circuit. The generated current is proportional to the magnetic flux going through the antenna of the user credential.

3.5.2. Data exchange

The carrier frequency of the magnetic field is used as a fundamental clock signal for the communication between the reader and the credential. It is also used as a fundamental clock input for the integrated circuit microprocessor to function.

To send data to the user credential the reader modulates the amplitude of the field. There are several amplitude modulation and data encoding rules defined in ISO/IEC 14443. The reader should refer to the standard for further details.

To answer the reader, the integrated circuit card of the user credential modulates its way of loading (impedance) the field generated by the reader. Here also further details can be found in

ISO/IEC 14443.

In the ISO/IEC 14443 standard, the reader is called the proximity coupling device (PCD)

In the ISO/IEC 14443 standard, the user credential is called proximity integrated chip card (PICC)

CLOUD 45

0 F R

EFERENCE

ANUAL

3.5.3. Recommendations

The communication between the reader and the user credential is sensitive to the presence of material or objects interfering with the magnetic field generated by the reader.

The presence of conductive materials like metal in the vicinity of the reader and the user credential can significantly degrade the communication and even make it impossible. The magnetic field of the reader generates Eddy or Foucault’s currents in the conductive materials; the field is literally absorbed by that kind of material.

 It is recommended for proper communication to avoid putting CLOUD 45x0 F in close proximity of conductive materials.

A minimum distance of 2.5cm (1”) should be kept.



To prevent the fields of adjacent readers to interfere with each other, a minimum distance between readers of 2.5cm (1”) should be kept.

The presence of multiple user credentials in the field also interferes with the communication.

When several user credentials are in the field of the reader, load of the field increases which implies that less energy is available for each of them and that the system is detuned. For this reason, Identive has implemented in its driver only one slot.



It is recommended to present only one user credential at a time in front of

CLOUD 45x0 F.

The communication between the reader and the credential is sensitive to the geometry of the system {reader, credential}. Parameters like the geometry and especially the relative size of the reader’s and credential’s antennas directly influence the inductive coupling and therefore the communication.

CLOUD 45x0 F was designed and optimized to function with user credentials of various technologies and sizes.



It may happen, that CLOUD 45x0 F is not capable of communicating with extremely large or extremely small credentials.



In order to optimize the coupling between the reader and the credential, it is recommended to put both antennas as parallel as possible to each other



In order to optimize transaction speed between the reader and the card it is recommended to place the credential as close as possible to the reader. This will increase the amount of energy supplied to the user credential which will then be able to use its microprocessor at higher speeds

3.6. Applications

3.7.1. General

CLOUD 4500 F is a transparent reader module designed to interface a personal computer host supporting PC/SC interface with 13.56MHz user tokens like public transport cards, contactless banking cards, electronic identification documents

– e.g. e-passports, e-ID cards, driving licenses etc. and smartcards according to ISO7816 as well as synchronous memory cards like

CAC and PKI cards and health insurance cards.

User credentials can have several form factors like credit cards, key fobs, NFC mobile phones or USB dongles like our SCTxxxx or @MAXX products.

CLOUD 45

0 F R

EFERENCE

ANUAL

CLOUD 4510 F incorporates a SAM slot for SIM-sized cards instead of the standard card slot for ID-1 sized cards of the CLOUD 4500 F.

RF link (13.56MHz)

ISO14443 interface

Smartcard contacts

ISO7816

Network

USB link

PC/SC interface

5 x0

CLOUD 4500

CLOUD 4510

Host CLOUD 45x0 F

Interface device

Credentials/SAM

Application logic

Application logic + User personal data for given set of applications

CLOUD 45x0 F itself handles the communication protocol but not the application related to the credential or card. The application-specific logic has to be implemented by software developers on the host.

3.7.2. Applications provided by Identive

Identive does not provide payment or transport applications or PKI or CAC applications.

Identive provides a few applications for development and evaluation purposes that can function with CLOUD 45x0 F. There are many tools provided; here are two of them:



The Simple NFC Tag Editor is part of our NFC-NDEF Editor Kit that enables the user to read and write NFC forum compliant records from/to NFC forum compatible tags.

It is an easy to use tool to configure NFC forum tag demonstrations rapidly, available in our web shop .



Smart card commander version 1.3 provides capabilities to identify most common cards in the field and display the content of them as well as scripting functionality, which can be very useful for developers to develop and debug their applications.

This tool is as well part of all our SDKs and available as a stand-alone product .

CLOUD 45

0 F R

EFERENCE

ANUAL

4. CLOUD 45x0 F characteristics

4.1. CLOUD 45x0 F high level architecture

4.1.1. Block diagram

The link between CLOUD 45x0 F and the host to which it is connected is the USB interface providing both the power and the communication channel.

ISO7816 contact smart card interface

To host

Device controller RF front-end

EMC filter +

Matching circuitry text text text

LED

The device controller has several interfaces available. In the CLOUD 45x0 F implementation three peripherals are connected to the device controller:



LED for reader status indication



A contact smart card interface



An RF front-end that handles the RF communication

The controller contains the firmware developed by Identive to handle all the ISO7816 contact protocol, the RF communication protocols and the PC/SC communication protocol with the host. The flash can be upgraded once the device is deployed in the field, hence enabling firmware upgrades to add and potentially patch features.

The RF front-end ensures the coding/decoding/framing modulation/demodulation required for the RF communication. It is controlled by the device controller through registers.

The matching circuitry provides the transmission and receiver paths adaptation for the antenna to function properly.

CLOUD 45

0 F R

EFERENCE

ANUAL

4.1.2. Software architecture

Applications can interface with the driver directly through the PC/SC interface.

Contact Reader

Contactless

Reader

PC/SC Layer

Driver

- Contact Smart Card

Reader

Driver

- Contactless Card

Reader

T= 0 / T= 1

SLOT 0

T = CL

SLOT 1

FIRMWARE

LAYER

CLOUD 45x0 F

Reader

ICC

PICC

The CLOUD 45x0 F leverages a PC/SC CCID driver that is freely available for all supported operating systems (Windows, MacOSX and Linux). With current Windows versions (starting with Windows Vista) and MacOSX, this driver is already included in the basic installation.

With the diverse Linux derivatives, there may be distribution specific drivers that should get installed using the install mechanism of the used distribution.

If there is none, the driver may always be downloaded from the webpage of the maintainer,

Ludovic Rousseau, https://alioth.debian.org/frs/?group_id=30105 .

Additionally, Identive provides a proprietary driver for all the supported OSs.

CLOUD 45

0 F R

EFERENCE

ANUAL

4.2. Quick reference data

Item

4.2.1. CLOUD 45x0 F dimensions

Characteristic Value

Weight

External dimensions

37g

100 mm X 70 mm X 11 mm

CLOUD

4500 F

Default label

Weight

External dimensions

CLOUD

4510 F

Default label

27g

100 mm X 70 mm X 10 mm

Drawing with dimensions of the CLOUD 45x0 F can be found in annex.

CLOUD 45

0 F R

EFERENCE

ANUAL

4.2.2. LED behavior

CLOUD 45x0 F is equipped with one bicolor LED. Its behavior is described in the table below.

GREEN RED Reader states

Just after plug-in (with drivers already installed)

ON OFF

Just after DFU operation

Suspend / standby

OFF

Reader powered, Contact card

IN, but not powered

Reader powered, Contactless card IN, but not powered

OFF

Contact card powered / communication

Contactless card powered / communication

Reader / card errors

500ms ON

500ms OFF

500ms ON

500ms OFF

OFF

500ms ON

500ms OFF

100ms ON

100ms OFF

Dual interface card powered in contact Slot

Dual interface card powered using RF field

500ms ON

500ms OFF

500ms ON

500ms OFF

OFF

500ms ON

500ms OFF

4.2.3. Other data

Parameter

4.2.3.1. General

Value/Description

Clock of the device controller

API

Operating temperature range

Operating humidity range

Certifications

8MHz

PC/SC 2.0

0º to 50ºC

Up to 95%RH non condensing

USB

FCC

WEEE

RoHS2

REACH

WHQL

CLOUD 45

0 F R

EFERENCE

ANUAL

Parameter

4.2.3.2. USB

Value/Description

DC characteristics

USB specification

USB Speed

Device Class

PID

VID

High bus powered (CLOUD 45x0 F draws power from USB bus)

Voltage: 5V

Avg. Current : 110mA (RF on, no cards present)

Suspend Current: 400µA

USB 2.0 FS Device

Full Speed Device (12Mbit/s)

CCID

0x5720 for CLOUD 4500 F; 0x5721 for CLOUD 4510 F

0x04E6

Parameter

4.2.3.3. Contact card interface

Value/Description

Smart card operating frequency

Maximum supported card baud-rate

Cards supported

ISO-7816 compliant

CT-API compliant

Number of slots

Ejection mechanism up to 12MHz

600Kbps

ISO/IEC 7816 smart cards - Class A, B and C

Synchronous smart cards

Yes

Single smart card slot

Manual

Parameter

4.2.3.4. Contactless interface

Value/Description

RF carrier frequency 13.56MHz +/-50ppm

Maximum supported card baud-rate

848Kbps

Cards supported



MIFARE: Classic 1K and 4K, DESFire, DESFire EV1, Ultralight,

Ultralight C, MIFARE mini and MIFARE Plus



FeliCa™ 212 and 424 Kbps support: FeliCa Standard/Lite



NFC forum tag type 1, 2, 3, 4

 iCLASS UID support

 my-d move

– SLE 66RxxP, my-d move NFC – SLE 66RxxPN,

SLE 66RxxS, SLE 55RxxE



NFC enabled Smart Phones and Tablets

ISO-14443A and B compliant

Number of slots

Ejection mechanism

Yes

Manual

tested with available device during development & qualification phase

CLOUD 45

0 F R

EFERENCE

ANUAL

5. Software modules

5.1. Installation

On Operating Systems with a CCID driver pre-installed, no installation is necessary.

Where there’s no CCID driver pre-installed – e.g. Linux systems or old Windows systems – the driver has to be installed using distribution-specific measures or using the available source packages.

Due to some limitations of the available CCID drivers under some circumstances, Identive does provide a dedicated driver for this reader, as well, which is available through Windows Update or on the Identive support pages .

5.2. Utilities

The following utilities are available:



A tool for testing the resource manager



A tool called PCSCDiag capable of providing basic information about the reader and a card through PC/SC stack

5.3. Driver

5.3.1. CLOUD 45x0 F listing

CLOUD 45x0 F is listed by PC/SC applications as



Identive CLOUD 47x0 F Contact Reader



Identive CLOUD 47x0 F Contactless Reader

5.3.2. Supported operating systems



Windows XP (32 & 64 bit)



Windows 2003 Server (32 & 64 bit)



Windows Vista (32 & 64 bit)



Windows Server 2008 (32 & 64 bit)



Windows 7 (32 & 64 bit)



Windows 8 (32 & 64 bit)



MacOS X



Linux

CLOUD 45

0 F R

EFERENCE

ANUAL

5.3.3. PC/SC 2.0 compliant ATR for contactless interface

When a user credential is placed on the reader, initialization, anti-collision is done. The user credential is automatically activated and an ATR is built as defined in the PC/SC specification.

For further information, please refer to section 3.1.3.2.3 of [PCSC3] and to [PCSC3-SUP]

5.3.3.1. ATR for contactless storage user tokens

The ATR of the credential is composed as described in the table below. In order to allow the application to identify the storage card properly, it’s Standard and Card name describing bytes must be interpreted according to the Part 3 Supplemental Document, maintained by PC/SC.

Credentials using technology like MIFARE are examples of this:

Byte# Value Designation Description

4...3+n

4+n

0x3B

0x8n

0x80

0x01

0x80

0x4F

Length

RID

PIX

0x00 0x000x000x00

Initial header

T0 n indicates the number of historical bytes in following ATR

TD1 upper nibble 8 indicates no TA2, TB2, TC2 lower nibble 0 means T=0

TD2 upper nibble 0 indicates no TA3, TB3, TC3 lower nibble 1 means T=1

A status indicator may be present in an optional TLV data object

Optional TLV data object

TCK

Tag: Application identifier

1 byte

Registered identifier on 5 bytes

Proprietary identifier extension on 3 bytes

4 RFU bytes

XOR of all previous bytes

Example of the ATR built for contactless storage tokens:

MIFARE Classic 4K MIFARE Ultralight

CLOUD 45

0 F R

EFERENCE

ANUAL

5.3.3.2. ATR for ISO/IEC 14443-4 user tokens

The credential exposes its ATS or application information which is mapped to an ATR. The table describes how this mapping is done.

Byte# Value Designation Description

4...3+n

0x3B Initial header

0x8n T0 n indicates the number of historical bytes in following ATR

0x80 TD1 upper nibble 8 indicates no TA2, TB2, TC2 lower nibble 0 means T=0

0x01 TD2 upper nibble 0 indicates no TA3, TB3, TC3 lower nibble 1 means T=1

4+n

Historical bytes application information or

TCK

Type A: the historical bytes from the ATS (up to 15 bytes)

Type B (8 bytes):



Byte 0 through 3: application data from ATQB,



Byte 4 through 6: protocol info byte from ATQB,



Byte 7: highest nibble is the MBLI (maximum buffer length index) from ATTRIB, lowest nibble is 0x0

XOR of all previous bytes

Example of the ATR built for an ISO14443-4 credential:

Type A Type B

CLOUD 45

0 F R

EFERENCE

ANUAL

5.4. Firmware

5.4.1. CCID transport protocol

CLOUD 45x0 F implements a transport protocol that is compliant with USB Device Class:

Smart Card CCID Specification for Integrated Circuit(s) Cards Interface Devices Revision 1.10.

This paragraph describes the CCID specification features that are implemented.

5.4.1.1. CCID class requests supported



Abort

5.4.1.2. CCID messages supported

The following CCID messages are supported for the contact interface when received through bulk-out endpoint.



PC_to_RDR_IccPowerOn



PC_to_RDR_IccPowerOff



PC_to_RDR_GetSlotStatus



PC_to_RDR_XfrBlock



PC_to_RDR_GetParameters



PC_to_RDR_ResetParameters



PC_to_RDR_SetParameters



PC_to_RDR_Escape



PC_to_RDR_ICCClock



PC_to_RDR_T0APDU



PC_to_RDR_Abort



PC_to_RDR_SetDataRateAndClockFrequency

5.4.1.3. CCID Error Codes

Extensive error codes are reported on many conditions during all CCID responses. Most of the error messages are reported by the CCID appropriately. Some of the main error codes for the contact interface are:



HW_ERROR



XFR_PARITY_ERROR



ICC_PROTOCOL_NOT_SUPPORTED



BAD_ATR_TS



BAD_ATR_TCK



ICC_MUTE



CMD_ABORTED



Command not supported

The following sub-sections discuss when and why these error codes are returned:

CLOUD 45

0 F R

EFERENCE

ANUAL

5.4.1.3.1. HW_ERROR

This error code is returned when a hardware short circuit condition is detected, during application of power to the card or if any other internal hardware error is detected.

5.4.1.3.2. XFR_PARITY_ERROR

This error code is returned when a parity error condition is detected. This error will be reported in the response to a PC_to_RDR_XfrBlock message.

5.4.1.3.3. ICC_PROTOCOL_NOT_SUPPORTED

This error code is returned if the card is signaling to use a protocol other than T=0 or T=1 in its

ATR.

5.4.1.3.4. BAD_ATR_TS

This error code is returned if the initial character of the ATR contains invalid data.

5.4.1.3.5. BAD_ATR_TCK

This error code is returned if the check character of the ATR contains is invalid.

5.4.1.3.6. ICC_MUTE

This error code is returned when the card does not respond until the reader time out occurs.

This error will be reported in the response to PC_to_RDR_XfrBlock message and

PC_to_RDR_IccPowerOn messages.

5.4.1.3.7. CMD_ABORTED

This error code is returned if the command issued has been aborted by the control pipe.

5.4.1.3.8. Command not supported

This error would be returned, if the command would not be supported by the reader.

CLOUD 45

0 F R

EFERENCE

ANUAL

6. Commands description

6.1. Generic APDU

6.1.1. Working with DESFire and MIFARE Plus tokens

To work with DESFire EV1 and MIFARE Plus tokens, please refer to the according application notes [AN337] and [AN338], respectively.

Please note that, since these application notes contain information available only under NDA with NXP, you’d need to sign an NDA with NXP to be allowed to receive them.

6.1.2. PAPDU_GET_UID

GET UID will retrieve the UID or SNR or PUPI of the user token. This command can be used for all supported technologies.

Command APDU

CLA

0xFF

INS

0xCA

0x00

Data in

Setting Le = 0x00 can be used to request the full UID or PUPI. (e.g. for ISO14443A single 4 bytes, double 7 bytes, triple 10 bytes, for ISO14443B 4 bytes PUPI).

Response APDU:

Data

Requested bytes of UID

Status Word

SW1, SW2

6.1.3. PAPDU_ESCAPE_CMD

Usually escape commands are transmitted through SCardControl as defined in PCSC API using IOCTL_CCID_ESCAPE. But on some environments, the driver will block this IOCTL unless the registry has been edited to allow it. Hence this vendor specific APDU was defined to transmit Escape commands to the reader as below

Command APDU

CLA

0xFF

INS

0xCC

0x00

Length of data

Data in

Escape

Command

Buffer

Response APDU:

Data

Reader Response

Status Word

SW1, SW2

CLOUD 45

0 F R

EFERENCE

ANUAL

Example:

To issue the “READER_GETIFDTYPE (0x12)” escape command , this pseudo APDU would be used:

Command APDU : FF CC 00 00 01 12

Response : 20 57 90 00

To issue the “READER_SETMODE (0X01)” escape command, this pseudo APDU would be used:

Command APDU : FF CC 00 00 02 01 01 (to set to EMV mode)

Response APDU : 90 00

Note:

1) To send Escape commands using this method, the reader should be connected in shared mode using T0 or T1 protocol. Only then would the resource manager allow

SCardTransmit.

As the escape commands defined using “

READER_GENERIC_ESCAPE

” have ISO

7816 APDU format, they can be sent using SCardTransmit without having any need to prepend “FF CC 00 00 P3”.

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2. Supported Pseudo APDU (Contactless Interface)

All Pseudo APDUs specific to Contactless Interface supported in the reader are explained in this section

6.2.1. PAPDU_MIFARE_READ_BINARY

This command is used to read data from a Mifare card. Refer to section 3.2.2.1.8 of [PCSC3] for details.

Command APDU

Command

Read Binary

CLA

0xFF

INS P1 P2

0xB0 Addr MSB Addr LSB

Data

P1 and P2 represent the block number of the block to be read, starting with 0 for sector 0, block

0, continuing with 4 for sector 1, block 0 (sector no. x 4 + block no.)

Regardless of the value given in Le, this command will always return the entire block content:

16 bytes for Mifare Classic

4 bytes for Mifare UL and UL C

Response APDU:

Data

N bytes of block data

Status Word

SW1, SW2

Example:

For a Mifare Classic 1K card with the following content:

The following command will read the sixth block and yield the mentioned output:

APDU:

FF B0 00 05 02

SW12:

9000 (OK)

DataOut:

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

(16 bytes)

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.2. PAPDU_MIFARE_UPDATE_BINARY

This command is used to update the non-volatile memory of a Mifare card. Refer to section

3.2.2.1.9 of [PCSC3] for further details.

Command APDU

Data

data

Command CLA

Update Binary 0xFF

INS

0xD6

Addr MSB

Addr LSB

For a description of P1 and P2, see PAPDU_MIFARE_READ_BINARY

Lc has got to match the block size of the used card

16 bytes for Mifare Classic

4 bytes for Mifare UL and UL C

Response APDU:

Data Status Word

- SW1, SW2

Example:

To write the bytes AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 to block 7 of a Mifare Classic 1K, the following command has got to be issued:

APDU:

FF D6 00 06 10 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55

SW12:

9000 (OK)

Resulting in this content on the card:

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.3. PAPDU_MIFARE_LOAD_KEYS

This command is used to load the key to the volatile memory of the reader. It can be used for all kinds of contactless cards. Refer to section 3.2.2.1.4 of [PCSC3] for further details.

Command APDU :

Command CLA INS P1 P2 Lc

Key data

Data Le

Load Keys 0xFF 0x82 Key Struct Key Num

The Key Structure (P1) is defined as follows:

Key -

b7 b6 b5 b4 b3 b2 b1 b0 Description x x x

0: Card Key; 1 Reader Key

0: Plain Transmission, 1: Secured Transmission

0: Keys are loaded into the volatile memory

1: Keys are loaded into the non-volatile memory. x xxxx

RFU

If b6 is set, it is the Reader Key number that has been used for the encryption, else it is ignored.

Only one reader key (0x00) is supported by CLOUD

45x0 F

Notes

Card keys can be loaded in both “secure” and “non-secure” mode. Card keys can only be loaded to the Volatile memory of the reader.

2) To load the card keys in secure mode, the application developer has to know the 128 bit AES key of the reader. The default key is “00010203 05060708 0A0B0C0D

0F101112

”.

As a Mifare key is only 6 bytes in length, data needs to be padded as per pkcs7 padding scheme (see example below).

3) The Reader-key can only be loaded in the secure-mode to the non-volatile memory of the reader. The new key is first XORed with the old key and encrypted with the old key.

In order to validate the integrity of the processed key data, a 2 byte CRC has got to be sent following the key data. Refer to the example Load Keys

– Reader – Secure

for details.

4) The CRC16 is calculated as defined in CRC-16-CCITT (polynomial 0x8408) with an initial value of 0x0000.

Response APDU:

Data Status Word

- SW1, SW2

CLOUD 45

0 F R

EFERENCE

ANUAL

Examples

Load Keys

– Card – Non-Secure

The command to load Mifare key A “FF FFFFFFFFFF” is

FF82006006 FFFFFFFFFFFF

Load Keys

– Card – Secure:

If the default AES128 reader is key is 00010203 05060708 0A0B0C0D 0F101112 then the following explains the steps needed to calculate the key for secure mode.

Default reader key

: 00010203 05060708 0A0B0C0D 0F101112

Mifare Key to be loaded

: FFFFFFFF FFFF

Mifare key after padding

: FFFFFFFF FFFF0A0A 0A0A0A0A 0A0A0A0A

AES128 Encrypted

Load keys command

: 10229E33 189403FD A9C14110 B1BB02B4

: FF82406010 10229E33 189403FD A9C14110 B1BB02B4

Load Keys

– Reader – Secure

If the default AES128 reader is key is 00010203 05060708 0A0B0C0D 0F101112 then the following explains the steps needed to change the reader key to 10111213 15161718

1A1B1C1D 1F202122.

Reader old-key : A: 00010203 05060708 0A0B0C0D 0F101112

Reader new-key : B: 10111213 15161718 1A1B1C1D 1F202122

C = XOR (A, B) : C: 10101010 10101010 10101010 10303030

D = CRC16(C) : D: 1C5F

E = 0x00 - D : E: E3A1 (should be appended in LSB order)

F = AES-Encrypt (C) : F: 886B0872 7BDA4996 D296FB46 09D2C75F

Load-Keys Command : G: FF82E00012 886B0872 7BDA4996 D296FB46 09D2C75F A1E3

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.4. PAPDU_MIFARE_AUTHENTICATE

This command is used to authenticate using the key number. Refer to section 3.2.2.1.6 of

[PCSC3] for further details.

Command APDU :

Command CLA INS P1

General

Authenticate 0xFF 0x86 0x00

The data structure is defined as follows:

Byte # Value Description

0x00

0x05

Data

data

0x01

0x60

0x61

Response APDU:

Version

Block Number MSB (always 0x00 for Mifare

Classic cards)

Block Number LSB

Mifare Classic Key A

Mifare Classic Key B

Key number

– shall be set to 0x01

Data Status Word

- SW1, SW2

Example:

Load Key A unencrypted and authenticate for block 6 (sector 1, actually) with that key:

APDU:

FF 82 00 60 06 FF FF FF FF FF FF

SW12:

9000 (OK)

APDU:

FF 86 00 00 05 01 00 06 60 01

SW12:

9000 (OK)

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.5. PAPDU_MIFARE_READ_SECTOR

This command reads the specified sector from a Mifare Classic card (first 3 blocks of the sector, excluding the Key block) or the entire content of Mifare UL/UL C cards.

Command APDU:

Command CLA INS P1 P2 P3 Data

Read Sector FF B1 Addr MSB Addr LSB 0 -

Response APDU:

Data

Mifare classic - 48 bytes of sector data read from card /

Mifare UL

– Entire card data is returned (64 bytes)

Example

Status Word

SW1, SW2

Read sector 1 of a Mifare Classic 1K

APDU:

FF B1 00 01 00

SW12:

9000 (OK)

DataOut:

00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55

(48 bytes)

Read entire content of a Mifare UL:

APDU:

FF B1 00 01 10

SW12:

9000 (OK)

DataOut:

04 6B 5D BA 09 F8 01 80 70 48 00 00 E1 10 06 00

00 01 02 03 1D 6E 6F 6B 69 61 2E 63 6F 6D 3A 62

74 01 00 11 67 9F 5F B6 04 06 80 30 30 30 30 00

00 00 00 00 00 00 00 00 00 00 00 02 42 54 FE 00

(64 bytes)

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.6. PAPDU_MIFARE_READ_SECTOR_EX

This command read the specified sector from a Mifare Classic card (all the 4 blocks of the sector, including the Key block) or the entire content of Mifare UL/UL C cards.

Command APDU:

Command

Read Sector

Extended

Response APDU:

CLA

INS

Data

Mifare classic - 64 bytes of sector data read from card /

Mifare UL

– Entire card data is returned (64 bytes)

Addr MSB Addr LSB

SW1, SW2

Status Word

Example

Read sector 1 of a Mifare Classic 1K

APDU:

FF B3 00 01 10

SW12:

9000 (OK)

DataOut:

00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55 AA 55

00 00 00 00 00 00 FF 07 80 69 FF FF FF FF FF FF

(64 bytes)

Data

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.7. PAPDU_MIFARE_WRITE_SECTOR

This command writes the contained data to the specified sector of a Mifare classic or Mifare

UL/UL C card (first blocks of the sector, excluding the Key block are written in case of Mifare

Classic).

Command APDU:

Command CLA INS P1 P2 P3 Data

Write Sector FF D7 AddrMsb AddrLsb Lc Data

Lc (P3) has got to be 0x30 when writing to the small sectors of a Mifare Classic and 0xF0 when writing to the large sectors of a Mifare Classic 4K.

Lc has got to be 0x30 for Mifare UL and the data will get written from block 4 till the end of the memory.

Response APDU:

Data Status Word

- SW1, SW2

6.2.8. PAPDU_MIFARE_VALUE_BLK_OLD

This command increments or decrements the data in a Value Block on a Mifare Classic card.

Command APDU:

P2 P3 Data Command

Increment/

Decrement

OLD

CLA

INS

00 where P2 codes the block number.

The data field is structured as follows

Byte # Value Description

B2-B5

0xC0

0xC1

Decrement

Increment

Block number

Value (LSB first)

Block

Num

Lc Data

CLOUD 45

0 F R

EFERENCE

ANUAL

Response APDU:

Data

Status Word

SW1, SW2

Example: decrement block 4 by 1 (key loading and authentication not shown)

(block 4 has got to be set up as value block prior to executing this command, see datasheet for

Mifare Classic cards)

APDU:

FF B0 00 04 00 // Read Block 4

SW12:

9000 (OK)

DataOut:

A9 AA AA AA 56 55 55 55 A9 AA AA AA 05 FA 05 FA

(16 bytes)

APDU:

FF F0 00 04 06 C0 04 01 00 00 00 // decrement block 4 by 1

SW12:

9000 (OK)

APDU:

FF B0 00 04 00 // Read Block 4

SW12:

9000 (OK)

DataOut:

A8 AA AA AA 57 55 55 55 A8 AA AA AA 05 FA 05 FA

(16 bytes)

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.9. PAPDU_MIFARE_VALUE_BLK_NEW

This command increments or decrements the value of a data object if the card supports it. Refer to section 3.2.2.1.10 of [PCSC3-AMD1] for further details.

Command APDU:

Command

Increment/

Decrement

CLA

INS

Data

BER-

TLV

The data object consists of a TLV structure that defines, which action should be performed, which block the actions pertain to (the destination(s)) and which value should be applied for the action.

Tags for the action include:

0xA0: Increment

0xA1: Decrement

The Tag to define the destination is:

0x80: Destination

The Tag to define the value is:

0x81: value to increment or decrement Destination by, LSB first

Example

Increment block 5 by 100

FF C2 00 03 0B

A0 09

80 01 05 increment block 5

81 04 64 00 00 00 by 100

This command returns a Response APDU according to section 2.2 of [PCSC3-SUP2].

Response APDU:

Data

C0 03 Error status, see below

Status Word

SW1, SW2 (card itself will send SW1, SW2)

CLOUD 45

0 F R

EFERENCE

ANUAL

Error Status

XX SW1 SW2

00 90 00

XX 62 82

XX 63 00

XX 63 01

XX 6A 81

XX 67 00

XX 6A 80

XX 64 00

XX 64 01

XX 6F 00

Description

XX = number of the bad data object in the APDU;

00 = general error of APDU;

01 = error in the 1

data object;

02 = error in the 2

data object; etc.

No error occurred

Data object XX warning, requested information not available

No information.

Execution stooped due to failure in other data object

Data object XX not supported

Data object XX with unexpected length

Data object XX with unexpected vale

Data Object XX execution error (no response from IFD)

Data Object XX execution error (no response from ICC)

Data object XX failed, no precise diagnosis

6.2.10. PAPDU_TCL_PASS_THRU (T=CL Pass Thru)

This command can be used to send raw data using T=CL protocol to a card. Please refer to the status words defined by the PICC manufacturer for a description of the status words

Command APDU:

Command CLA INS P1 P2 P3 Data

Pass-through FF FE 00 00 Lc Data

Response APDU:

Data

PICC response data

Status Word

SW1, SW2 (card itself will send SW1, SW2)

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.11.

Thru)

PAPDU_ISO14443_PART3_PASS_THRU (Mifare Pass

This command is used to send raw data using Type A standard framing to a card. CRC bytes will be appended automatically. The reader will not add transport protocol data to the raw data

– e.g. PCB, NAD, CID etc.

Command APDU:

Command

Part 3 Passthrough

CLA

INS

Transmit

CRC

P1 = 0x00 will transmit the CRC bytes form the card as is to the application.

P1 = 0x01 will discard the CRC bytes.

Response APDU:

Data Status Word

Data

Data

Data returned by card SW1, SW2

6.2.12. PAPDU_ISO14443_PART4_PART3_SWITCH (TCL

–

Mifare Switch)

This command switches the card state between TCL and MIFARE modes

Command APDU:

Command

Part 4-Part 3

Switch

CLA

INS

P1 = 0x00 switches from MIFARE mode to TCL mode

P1 = 0x01 switches from TCL mode to MIFARE mode

Response APDU:

Data

Status Word

Data

- SW1, SW2

NOTE: This command is mainly targeted at Mifare plus S0 cards. Mifare plus card at S0 level get detected as Mifare memory card. In order to personalize these cards first it needs to be switched to Part 4 mode. For this purpose this user command needs to be issued using

SCardTransmit function.

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.13. PAPDU_FELICA_REQC

This command Issues REQC as defined in JIS 7.5.1. It is used to detect the presence of a NFC

Forum tag type 3 in the field

Command APDU:

Command

FeliCa REQC

CLA

INS

Data

2 bytes of system code,

1 byte RFU, 1 byte TSN

Response APDU:

Data

16 bytes of NFCID2 + 2 bytes of System Code (sent only if the RFU byte is 0x01)

Status Word

SW1, SW2

6.2.14. PAPDU_FELICA_REQ_SERVICE

This command issues a REQ SERVICE as defined in JIS 9.6.2. P1. On receiving this command an NFC Forum tag type 3 will respond with the area key version of the specified area and the service key version of the specified service.

Command APDU:

Command

FeliCa REQ

Service

CLA

Response APDU:

INS

Number of services/areas

Data

8 bytes IDm + No. of Service or areas(n) + Service version or area version list (2*n)

2 *

Status Word

SW1, SW2

Data

Service Code List

/ Area Code List

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.15. PAPDU_FELICA_REQ_RESPONSE

This command issues a REQ RESPONSE as defined in JIS 9.6.1. When an NFC Forum tag type 3 receives this command, it responds with its current mode (0/1/2).

Command APDU:

Command

FeliCa REQ

Response

CLA

Response APDU:

INS

Data

Data Status Word

8 bytes IDm + Mode SW1, SW2

6.2.16. PAPDU_FELICA_READ_BLK

This command issues a READ as defined in JIS 9.6.3



P1 specifies the number of service



P2 specifies the number of blocks



Data buffer specifies the service code and block list

When an NFC Forum tag type 3 receives this command, it responds with the record value of the specified service.

Command APDU:

Command CLA INS P1 P2 P3

FeliCa REQ

Response

FF 46

Number of service

Number of blocks

2*(P1 + P2)

Data

Service

Code List,

Block List

Response APDU:

Data

8 bytes IDm + Status Flag 1 + Status Flag 2 +

No. of blocks(n) + Block data (n*16)

Status Word

SW1, SW2

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.17. PAPDU_FELICA_WRITE_BLK

This command issues a WRITE as defined in JIS 9.6.4



P1 specifies the number of service



P2 specifies the number of blocks

When an NFC Forum tag type 3 receives this command, it writes the records of the specified service.

Command APDU:

Command

FeliCa Write

Block

CLA

0xFF

INS

0x48

Number of service

Number of blocks

2*(P1 +

P2) + (16

* P2)

Data

Service Code

List, Block List,

Block Data

Response APDU:

Data Status Word

8 bytes IDm + Status Flag 1 + Status Flag 2 SW1, SW2

6.2.18. PAPDU_FELICA_SYS_CODE

This command issues a REQ SYSTEM CODE as defined in RC-S850 / 860 Command-Ref-

Manual Section 6.1.7

Command APDU:

Command

FeliCa REQ

SYSTEM

CODE

CLA

Response APDU:

INS

Data

8 bytes IDm + No. of System Codes (n) + System Code

List (2n)

Status Word

SW1, SW2

Data

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.19. PAPDU_NFC_TYPE1_TAG_RID

This command issues a RID to get the tag’s identification data.

Command APDU:

Command CLA INS P1 P2

50 00 00 TYPE1 Tag RID

Response APDU:

Data

Status Word

Data

HR0 HR1 UID0 UID1 UID2 UID3 SW1, SW2

Where



HR0 and HR1 are the 2 bytes Header ROM which identify the tag



UID0 through UID3 are the first 3 bytes of the tag’s UID.

Topaz tags have 7 bytes long UID which can be fully fetched using the GET_UID APDU

described earlier in this manual.

6.2.20. PAPDU_NFC_TYPE1_TAG_RALL

This command issues a RALL to read the two header ROM bytes and the whole of the static memory blocks 0x0-0xE.

Command APDU:

Command

TYPE1 Tag

RALL

CLA

INS

Data

Response APDU:

Data Status Word

HR0 HR1 120 bytes (Blocks 0

– E)

SW1, SW2

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.21. PAPDU_NFC_TYPE1_TAG_READ

This command issues a READ to read a single EEPROM memory byte within the static memory model area of blocks 0x0-0xE.

Command APDU:

Data Command

TYPE1 Tag

READ

CLA

INS

Byte Addr

Where P2 codes the address of the memory byte in the following way:

Bit numbers

– b3 b2

– b0

Description

Block # (value between 0x0 and 0xE)

Byte # within the block (value between 0 and 7)

Response APDU:

Data Status Word

Data returned by card SW1, SW2

6.2.22. PAPDU_NFC_TYPE1_TAG_WRITE_E

This command issues a WRITE to erase and then write the value of 1 memory byte within the static memory model area of blocks 0x0-0xE.

Command APDU:

Command

TYPE1 Tag

WRITE ERASE

CLA

INS

Byte Addr

Where P2 codes the address of the memory byte in the following way:

Bit numbers

– b3 b2

– b0

Description

Block # (value between 0x0 and 0xE)

Byte # within the block (value between 0 and 7)

Response APDU:

Data Status Word

Data

Data

Data returned by card SW1, SW2

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.23. PAPDU_NFC_TYPE1_TAG_WRITE_NE

This command issues a WRITE-NE to write a byte value to one byte within the static memory model area of blocks 0x0-0xE. It does not erase the value of the targeted byte before writing the new data. Execution time of this command for NFC Forum tags type 1 is approximately half that of the normal write command (WRITE-E). Using this command, EEPROM bits can only be set, not reset.

Command APDU:

Command

TYPE1 Tag WRITE

No ERASE

CLA

INS

Byte Addr

Where P2 codes the address of the memory byte in the following way:

Bit numbers

– b3 b2

– b0

Description

Block # (value between 0x0 and 0xE)

Byte # within the block (value between 0 and 7)

Response APDU:

Data Status Word

Data

Data

Data returned by card SW1, SW2

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.24. PAPDU_NFC_TYPE1_TAG_RSEG

This command issues a RSEG to read out a complete segment (or block) of the memory within dynamic memory model.

Please note that this command works only on specific Topaz tags in the dynamic memory model.

Command APDU:

Command

TYPE1 Tag READ

SEGMENT

CLA

INS

SegAddr

Data

Where P2 Segment Address is:

Bit numbers

– b4 b2

– b0

Response APDU:

Data

Description

Segment (0x0

– 0xF)

Status Word

128 bytes of data SW1, SW2

6.2.25. PAPDU_NFC_TYPE1_TAG_READ8

This command issues a READ8 to read out a block of eight bytes.

Please note that this command only works on Topaz tags in dynamic memory model.

Command APDU:

Command

TYPE1 Tag

READ BLOCK

CLA

Where P2 Block Address is:

Bit numbers

– b0

Response APDU:

Data

INS

Block

Addr

Description

General block (0x00 -0xFF)

Status Word

Data

8 bytes of data SW1, SW2

CLOUD 45

0 F R

EFERENCE

ANUAL

6.2.26. PAPDU_NFC_TYPE1_TAG_WRITE_E8

This command issues a WRITE8 to erase and then write a block of eight bytes.

Please note that this command only works on Topaz tags in dynamic memory model.

Command APDU:

Command

TYPE1 Tag

WRITE and

ERASE BLOCK

CLA

Where P2 Block Address is:

Bit numbers

– b0

Response APDU:

Data

INS

Block

Addr

Description

General block (0x00 -0xFF)

Status Word

Data

Data

8 bytes of data that have been written SW1, SW2

6.2.27. PAPDU_NFC_TYPE1_TAG_WRITE_NE8

This command issues a WRITE8 to write a block of eight bytes. It does not erase the value of the targeted byte before writing the new data. Using this command, EEPROM bits can be set but not reset.

Please note that this command only works on Topaz tags in dynamic memory model.

Command APDU:

Command

TYPE1 Tag

WRITE and NO

ERASE BLOCK

CLA

Where P2 Block Address is:

INS

Block

Addr

Data

Data

Bit numbers

– b0

Response APDU:

Description

General block (0x00 -0xFF)

Data Status Word

8 bytes of data SW1, SW2

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3. Escape commands for the CLOUD 45x0 F

With Amendment 1 of the PC/SC specification, Part 3, a method to define vendor specific commands has been introduced.

CLOUD 45x0 F provides the command

READER_GENERIC_ESCAPE to send commands

using this method. However, most of the escape commands listed here is not defined according to this method because of backward compatibility reasons.

All newly defined commands will adhere to this new standard. See the command

CONTACT_READ_INSERTION_COUNTER as an example.

6.3.1. Sending Escape commands to CLOUD 45x0 F

A developer can use the following methods to send Escape commands to CLOUD 45x0 F



SCardControl method defined in PC/SC API



SCardTransmit method defined in PC/SC API in conjunction with the Escape command APDU

Please note, that SCardTransmit will only work when connected to a card.

When using the CCID driver for Windows, in order to be able to send Escape commands for the CLOUD 45x0 F, this feature has got to be enabled by setting a REG_DWORD value named

‘EscapeCommandEnable’ in the registry to a value of ‘1’.

When using the Identive supplied driver, this will not be necessary.

For Windows XP and Windows Vista, the key to hold the value for CLOUD 4500 F would be

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\USB\VID_04E6&PID_5720\

Device-Instance-xxxx \Device Parameters

The one for CLOUD 4510 F would be

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\USB\VID_04E6&PID_5721\

Device-Instance-xxxx \Device Parameters

For Windows 7 and Windows 8, the value for CLOUD 4500 F would be

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\USB\VID_04E6&PID_5720\Devi ce-Instance-xxxx \Device Parameters\WUDFUsbccidDriver

The one for CLOUD 4510 F would be

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\USB\VID_04E6&PID_5721\Devi ce-Instance-xxxx \Device Parameters\WUDFUsbccidDriver

Device-Instance-xxxx has got to be equal to the serial number of the reader used, so this modification has got to be made for every physical reader intended to be used on the machine in question. The reader has got to be plugged in at least once for the mentioned key to exist and the driver has got to be restarted for this setting to take effect. (Unplug and re-plug the reader).

To be able to work with synchronous memory cards using our MCard API, the same setting will have to be established.

See appendix B for some sample code sending Escape commands to the reader.

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.2. Escape command codes

Escape commands can be used by an application to configure CLOUD 45x0 F to function in a mode that is not its default configured mode or to get specific information. To put the CLOUD

45x0 F back into its default mode, it either has to be unplugged and plugged again or the application can send the same Escape command again.

The following Escape commands are supported by CLOUD 45x0 F:

6.3.3. Common for Contact and Contactless Interfaces

ESCAPE COMMAND

READER_SETMODE

READER_GETMODE

READER_GETIFDTYPE

READER_LED_CONTROL

READER_GETINFO_EXTENDED

ESCAPE CODE

0x01

0x02

0x12

0x19

0x1E

READER_LED_CONTROL_BY_FW

READER_RDWR_USR_AREA

READER_GENERIC_ESCAPE

0xB2

0xF0

FF 70 04 E6 XX

6.3.3.1. READER_SETMODE

This Escape command sets the current mode of the reader. Applications may call this function, to set the desired mode. Typically, this call is used to switch between the ISO7816, EMV,

Memory card and NFC test mode operations. Upon power on the reader will reset to the default

ISO7816 mode.

Input:

The first byte of the input buffer contains the escape code value and the second one contains the value for the desired mode of operation. The output buffer field shall be NULL.

Byte0 Byte1

Escape code (0x01) Mode

CLOUD 45

0 F R

EFERENCE

ANUAL

The following table defines the values for the Mode parameter:

Mode

ISO 7816

EMV

Synchronous 0x02

NFC Test

Value

0x00

0x01

0x04

Remarks

ISO 7816 mode

– Applicable for both contact slot and contactless slot

EMV

– Applicable only for contact slot and ignored by contactless interface

Memory card mode (Synchronous)

– Applicable only for contact slot and ignored by contactless interface

NFC Test Mode

– Applicable only for contactless interface

ISO mode uses APDU mode of data transfer and is used for normal operation. This is the default mode of the reader on Power up.

EMV mode also uses APDU mode of data transfer and is used for EMV test purposes. This mode has more stringent checks for Smartcard detection and Communication as per EMV4.2 spec.

Synchronous mode is used for communicating only with Memory cards.

NFC test mode is used to ignore deactivate-activate sequence during SCardConnect.

(PC_TO_RDR_ICCPOWERON - 0x62, and PC_TO_RDR_ICCPOWEROFF

– 0x63)

Output:

Output buffer

NULL

6.3.3.2. READER_GETMODE

This Escape command retrieves the current mode of the reader.

Input:

The input buffer contains the escape code value.

Byte0

Escape code(0x02)

Output:

The currently active reader mode will be returned as a byte value

Mode

ISO

Value

0x00

Remarks

ISO 7816 mode

EMV 0x01

Synchronous 0x02

NFC Test 0x04

EMV mode

Memory card mode (synchronous)

NFC Test Mode

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.3.3. READER_GET_IFDTYPE

This Escape command is used to get the current IFD type from the reader.

Input:

The first byte of the input buffer contains the escape code.

Byte0

Escape code(0x12)

Output:

The reader returns its PID LSB first.

PID value

B0 B1

Description

0x20 0x57 Identive CLOUD 4500 F Dual Interface Reader

0x21 0x57 Identive CLOUD 4510 F Contactless + SAM Reader

6.3.3.4. READER_LED_CONTROL

This Escape command is used to toggle the LED state. LED control by firmware should be

disabled using the escape command READER_LED_CONTROL_BY_FW to see proper LED

change when using this IOCTL.

Input:

The first byte of the input buffer contains the escape code, followed by LED number (if more than one LED is present, else set to 0) and then desired LED state. This will be required for production purpose.

Byte0 Byte 1 Byte2

Escape code(0x19) LED number (0-RED,1-GREEN) LED state (0-OFF, 1-ON)

Output:

Output buffer

NULL

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.3.5. READER_GET_INFO_EXTENDED

This Escape command is used to get the firmware version, reader capabilities, and Unicode serial number of the reader.

Input:

The first byte of the input buffer contains the escape code.

Byte0

Escape code(0x1E)

Output:

The firmware will return data as per structure SCARD_READER_GETINFO_PARAMS_EX mentioned below.

Field Size in

Bytes

Field Name Field Description Value/Default

2 byMajorVersion Major Version in BCD

Based on current firmware version byMinorVersion bySupportedModes

Minor Version in BCD

Bit map indicating the supported modes of the reader.

0x01 => EMV mode

0x02 => Memory card mode

0x04 =>NFC test mode

0x07 for Contact +

Contactless readers

0x03 for Contact only readers

Note: ISO mode is not indicated as it is always supported. wSupportedProtocols

Protocols supported by the

Reader

Bit 0

– T0

Bit 1

– T1

0x0003

Received as LSB first

28 winputDevice byPersonality byMaxSlots bySerialNoLength abySerialNumber

IO_DEV_NONE

IO_DEV_KEYPAD

IO_DEV_BIOMETRIC

0x00

0x01

0x02

0x0000

Received as LSB first

Reader Personality (Not Used )

Maximum number of slots

Serial number length (0x1C)

0x00

0x02 (contact and contactless)

0x1C

Unicode serial number

Reader number serial

Received as MSB first

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.3.6. READER_LED_CONTROL_BY_FW

This Escape command is used to enable/disable LED control by firmware.

Input:

The first byte of the input buffer contains the escape code. The second byte specifies if LED control by firmware should be disabled or enabled. The output buffer is NULL.

Byte1

Byte0

Value Description

Escape code(0xB2)

0 Enable LED Control by firmware

1 Disable LED Control by firmware

Get State:

0 -- LED control by firmware enabled

1 -- LED control by firmware disabled

Output:

No response is returned for set state. For Get State 1 byte response is received.

Output buffer

NULL or current state

6.3.3.7. READER_RD_WR_USER_AREA

This Escape command is used to access the user data area in the reader. The user area is located in the non-volatile memory of the reader and hence data will be retained even after power cycle.

Note:



Frequent writes should be avoided (The non-volatile memory supports only 100K writing cycles).



A maximum of 249 bytes can be read and written. The sector can be read and written only as a whole.



If complete data (249 bytes) is not given during write operation then random data will be padded to the given data and then written. If you want to modify only part of the data, read the entire 249 bytes, modify the data you want to change and then write it back to the reader.

CLOUD 45

0 F R

EFERENCE

ANUAL

Input:

The first byte of the input buffer contains the escape code. The second byte specifies if user area is to be read or written as described below.

Byte1

Byte0

Byte2 to Byte251

Value Description

1 Read 249 bytes of user data None

Escape code(0xF0)

2 Write 249 bytes of user data Data to be written

Output:

Operation Data (Byte0-BYTE248)

Read

Write

249 bytes of user data

No bytes returned

6.3.3.8. READER_GENERIC_ESCAPE

This Escape command is used to invoke newly defined escape functions and send proprietary commands to the reader. It is defined in line with vendor specific generic command defined in

[PCSC3-AMD1].

Input:

The first five bytes of the input buffer shall follow APDU structure as per [PCSC3-AMD1]. 6

TH byte shall be the command code used to identify the specific command.

Byte0 Byte1 Byte2 Byte3 Byte4

0xFF 0x70 0x04 0xE6

From Byte5 (up to Lc bytes)

Byte 5 Byte 6 onwards

Lc (always

> 0)

Cmd

Opcode

Command parameters or data

ByteLc+5

(optional)

Output:

Depending on the command, the output shall be Le bytes of data + SW1 + SW2 or SW1+

SW2. The escape message shall at least return 2 bytes status word SW1, SW2. In case of success, SW1=0x90 and SW2=0x00 shall be returned. In error scenario, appropriate error status shall be returned (as defined in Error Code section 8.0).

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.3.9. READER _CONTROL_CONTACT_SLOT

This Escape command is supported through the READER_GENERIC_ESCAPE message.

This command can be used to disable the contact slot until it is re-enabled through the same command or until the reader is re-plugged. When a dual interface card is placed in the contact slot it will get detected in both “contact” and “contactless” mode. To enable applications to actively switch the detection from contact-only mode to contactless-only mode this Escape

command can be used along with CNTLESS_ SWITCH_RF_ON_OFF .

Input

To Enable / Disable / “Get-Current-Status” of Contact Slot

Byte0

CLA

Byte1 Byte2 Byte3 Byte4

INS P1 P2 Lc

Byte5 Byte6

0xFF

0x70

0x04

0xE6

0x03

0x02

Byte7

0x05

(opcode)

0x01

– to enable

0x00

– to disable

0x05

(opcode)

0x00 - to get current contact status

Byte2 and Byte3 constitute the world wide unique vendor ID as assigned by the USB organization. For Identive based readers Byte2 = 0x04 and Byte3 = 0xE6 since it USB Vendor

ID is 0x04E6

Output:

If the command is successful, a single byte is returned. This byte indicates the status of contact slot which needs to be interpreted as below.

Byte 0 Description

0x01

0x00

Contact slot is enabled

Contact slot is disabled

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4. Specific for Contactless Interface

ESCAPE COMMAND

CNTLESS_GETCARDINFO

ESCAPE CODE

0x11

CNTLESS_GET_ATS_ATQB

CNTLESS_CONTROL_PPS

CNTLESS_RF_SWITCH

CNTLESS_SWITCH_RF_ON_OFF

CNTLESS_GET_BAUDRATE

CNTLESS_CONTROL_RETRIES

CNTLESS_CONTROL_POLLING

CNTLESS_GET_CARD_DETAILS

CNTLESS_SET_CONFIG_PARAMS

CNTLESS_IS_COLLISION_DETECTED

CNTLESS_FELICA_PASS_THRU

0x93

0x99

0x96

0x9C

0x9E

0xA7

0xAC

0xDA

0xE1

0xE4

0xF3

CNTLESS_P2P_SWITCH_MODES

CNTLESS_P2P_TARGET_RECEIVE

CNTLESS_P2P_TARGET_SEND

CNTLESS_P2P_INITIATOR_DESELECT

0xE9

0xEA

0xEB

0xE6

CNTLESS_P2P_INITIATOR_TRANSCEIVE

CNTLESS_NFC_SINGLESHOT

0xE7

0xEC

CNTLESS_NFC_LOOPBACK 0xED

CNTLESS_GET_SET_NFC_PARAMS READER_ESCAPE_GENERIC (0x04)

CNTLESS_GET_P2P_EXTERNAL_RF_STATE READER_ESCAPE_GENERIC (0x06)

6.3.4.1. CNTLESS_GET_CARD_INFO

This Escape command is used to get information about the contactless card placed in the field of the reader.

Input:

The first byte of input buffer contains the escape code.

Byte0

Escape code(0x11)

CLOUD 45

0 F R

EFERENCE

ANUAL

Output:

Byte0

Contactless card present

(0x01)

Byte1 Byte2

Card to Reader communication baud rate (0xNN - see table below for details)

Card Type Info

(Upper nibble indicates memory card/T=CL/dual mode card;

Lower nibble indicates Type

A/ Type B card

See Table below for values)

Card to Reader communication baud rate BYTE is defined as follows:

– 212kbps supported (direction reader to card) b1

– 424kbps supported (direction reader to card) b2

– 848kbps supported (direction reader to card) b3

– always 0 b4

– 212kbps supported (direction card to reader) b5

– 424kbps supported (direction card to reader) b6

– 848kbps supported (direction card to reader) b7

– 1 – indicates same baud rate in both directions

– indicates different baud rates in both directions

Example:

If 0xNN = 0x77, the card supports all baud rates namely 106, 212, 424 and 848 kbps in both directions.

If 0xNN = 0xB3, the card supports 106, 212 and 424 kbps in both directions.

Card Type Info:

Upper Nibble Value Description

0 Memory card

T=CL card

Dual mode card

Lower Nibble Value

0 Type A card

Type B card

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.2. CNTLESS_GET_ATS_ATQB

This Escape command retrieves the ATS for Type A T= CL or the ATQB for Type B cards.

Input:

The first byte of input buffer contains the escape code.

Byte0

Escape code(0x93)

Output:

The output buffer contains the ATS bytes or the ATQB bytes depending on the type of PICC placed on the reader

6.3.4.3. CNTLESS_CONTROL_PPS

This Escape command disables the automatic PPS done by the firmware/device for contactless cards.

Input:

The first byte of input buffer contains the escape code.

The second byte either sets the mode or contains a code to retrieve the setting.

Input Output

Byte0

Byte1 - PPS control byte

Enable

Byte0

No Output

Escape code(0x99)

Disable

Get current status

No Output

– PPS is enabled

– PPS is disabled

Output:

No response is returned for set state. For Get State 1 byte response is received.

Output buffer

NULL or current state

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.4. CNTLESS_RF_SWITCH

This Escape command can be used to switch the RF field ON or OFF.

Input:

The first byte of input buffer contains the escape code.

The second byte either sets the mode or contains a code to retrieve the setting.

Byte0

Byte1

Value Description

Output

Byte0

0x00

Escape code(0x96)

0x01

0xFF

Switch RF Field OFF

No Output

Switch RF Field ON

No Output

– RF field is ON

Get current field state

– RF field is OFF

Output:

No response is returned for set state. For Get State 1 byte response is received.

Output buffer

NULL or current state

6.3.4.5. CNTLESS_SWITCH_RF_ON_OFF

This Escape command is used to switch the RF field ON or OFF when a contact smart card is inserted into the reader. By default, the RF field is always in the ON state and when a contact smart card is inserted in the reader, the RF field is turned OFF.

Input:

The first byte of input buffer contains the escape code.

The second byte either sets the mode or contains a code to retrieve the setting.

Byte0

Value

Byte1

Description

Output

Byte 0

0x00

Escape code(0x9C)

0x01

Switch RF Field OFF when contact card is present in the reader

Leave RF Field ON when contact card is present in the reader

No Output

0xFF

Get current field state

0x00 - RF is OFF when contact card is present in the reader

0x01 - RF is ON when contact card is present in the reader

After the RF is turned off, to turn the RF ON again, card connect has to be done in direct mode.

CLOUD 45

0 F R

EFERENCE

ANUAL

Output:

No response is returned for set state. For Get State 1 byte response is received.

Output buffer

NULL or current state

6.3.4.6. CNTLESS_GET_BAUDRATE

This Escape command is used to get the current baud rate of card-reader communication.

Input:

The first byte of input buffer contains the escape code.

Byte0

Escape code(0x9E)

Output:

The output contains a byte with the following possible values

Byte0 Description

0x00 106Kbps in both directions

0x01 106Kbps from PICC to PCD, 212Kbps from PCD to PICC

0x02 106Kbps from PICC to PCD, 424Kbps from PCD to PICC

0x03 106Kbps from PICC to PCD, 848Kbps from PCD to PICC

0x10 212Kbps from PICC to PCD, 106Kbps from PCD to PICC

0x11 212Kbps in both directions

0x12 212Kbps from PICC to PCD, 424Kbps from PCD to PICC

0x13 212Kbps from PICC to PCD, 848Kbps from PCD to PICC

0x20 424Kbps from PICC to PCD, 106Kbps from PCD to PICC

0x21 424Kbps from PICC to PCD, 212Kbps from PCD to PICC

0x22 424Kbps in both directions

0x23 424Kbps from PICC to PCD, 848Kbps from PCD to PICC

0x30 848Kbps from PICC to PCD, 106Kbps from PCD to PICC

0x31 848Kbps from PICC to PCD, 212Kbps from PCD to PICC

0x32 848Kbps from PICC to PCD, 424Kbps from PCD to PICC

0x33 848Kbps in both directions

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.7. CNTLESS_CONTROL_RETRIES

This Escape command is used to enable/disable CRC/PROTOCOL/TIMEOUT error retries which are enabled by default for contactless cards.

Input:

The first byte of input buffer contains the escape code.

The second byte either sets the mode or contains a code to retrieve the setting.

Byte0

Input

Byte1- Description

Output

Byte 0

0x00

Enable RNAK retries No Output

Escape code(0xA7)

0x01

0xFF

Disable RNAK retries

Get current state of retries

No Output

0x00 - Retries are enabled

0x01 - Retries are disabled

Output:

No response is returned for set state. For Get State 1 byte response is received.

Output buffer

NULL or current state

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.8. CNTLESS_CONTROL_POLLING

This Escape command is used to enable/disable firmware polling for contactless cards.

Input:

The first byte of input buffer contains the escape code.

The second byte either sets the mode or contains a code to retrieve the setting.

Byte0

Input

Byte1 - Description

Output

Byte 0

0x00 Enable polling No output

Escape code(0xAC)

0x01

0XFF

Disable polling

Get current state of polling

No output

0x00

– Polling enabled

0x01

– Polling disabled

Output:

No response is returned for set state. For Get State 1 byte response is received.

Output buffer

NULL or current state

6.3.4.9. CNTLESS_GET_CARD_DETAILS

This Escape command is used to get details about the PICC placed in the field of the reader.

Input:

The first byte of input buffer contains the escape code.

Byte0

Escape code(0xDA)

B14

B15

B16

B17

B18

B19

B20

B3-B12

B13

0x00

0x01

0x00

0x01

–B10

B11

B12

B13

B14

B15

CLOUD 45

0 F R

EFERENCE

ANUAL

Output:

Byte # Value

0x00

0x01

0x04

0x08

0x00

0x01

0x02

0x43

0x44

0x45

0x46

‘xx’

0x08

Description

Type A card

Type B card

FeliCa 212

FeliCa 424

Memory card

T-CL card

Dual interface card

FeliCa

Topaz

B-prime i-Class

‘xx’ is the PUPI / UID Length

For FeliCa cards

THEN EITHER

PUPI/UID bytes

0x00 byte padding used if length smaller than 10

CID not supported

CID supported

NAD not supported

NAD supported

Bit Rate Capability

FWI

IFSC

MBLI

SAK

SFGI

8 Bytes NFCID2

Request service command response time parameter (see

JIS-6319 specification)

Request response command response time parameter

Authentication command response time parameter

Read command response time parameter

Write command response time parameter

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.10. CNTLESS_SET_CONFIG_PARAMS

This Escape command is used to configure RXGAIN and RXTHRESHOLD of the RF receiver for different baud rates and card types. All configured parameters are volatile.

Input:

The first byte of input buffer contains the escape code. The following 16 bytes contain the below defined parameters.

Byte # Value

B0 0XE1

Description

Escape code

Type A RXGAIN for polling or 106Kbps

Type A RXGAIN for 212 Kbps

B10

Type A RXGAIN for 424 Kbps

Type A RXGAIN for 848 Kbps

Type A RX THRESHOLD for polling or 106Kbps

Type A RX THRESHOLD for 212 Kbps

Type A RX THRESHOLD for 424 Kbps

Type A RX THRESHOLD for 848 Kbps

Type B RXGAIN for polling or 106Kbps

Type B RXGAIN for 212 Kbps

B11

B12

B13

B14

Type B RXGAIN for 424 Kbps

Type B RXGAIN for 848 Kbps

Type B RX THRESHOLD for polling or 106Kbps

Type B RX THRESHOLD for 212 Kbps

B15

B16

Output:

Output buffer

NULL

Type B RX THRESHOLD for 424 Kbps

Type B RX THRESHOLD for 848 Kbps

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.11. CNTLESS_IS_COLLISION_DETECTED

This Escape command is used to identify if multiple Type A cards are detected in the field.

Input:

The first byte of input buffer contains the escape code.

Byte0

Escape code(0xE4)

Output:

Byte0

Value Description

0x00

0x01

Collision is not detected

Collision is detected

6.3.4.12. CNTLESS_FELICA_PASS_THRU

This Escape command is used as a pass through to send FeliCa commands to FeliCa cards.

Input:

The first byte of input buffer contains the escape code followed by FeliCa command to be sent to the card. At least 1 byte of command is required to be sent to the card. Otherwise an error will be reported.

Byte0 Byte1 onwards

Escape code (0xF3) FeliCa command bytes

Output:

The response received from the FeliCa card is sent as output for this escape command.

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.13. CNTLESS_P2P_SWITCH_MODES

This Escape command is used to switch the device between the reader/writer and P2P modes of operation and to query the current mode. By default, the device is in the reader/writer mode.

Input:

The first byte of input buffer contains the escape code.

The second byte either sets the mode or contains a code to retrieve the setting.

Additional data bytes will be needed for Initiator/Target mode.

Offset Description Detailed description

0xE9

– P2P Initiator mode

– P2P Target mode

– Reader / writer mode

0xFF

– Get current mode

Switch mode

For the switch to Initiator / Target mode, the bytes from offset 0x02 give additional information as described below

Offset

7 to N+7

Initiator Mode Bytes Detailed description

RFU

Timeout Low Byte

Timeout High Byte

General bytes to be sent in

ATR-REQUEST

Number of General Bytes

CLOUD 45

0 F R

EFERENCE

ANUAL

Offset

32 to N+32

0xFE

0x0F

0x40

0x01

0xFE

0x0F

0xBB

Target Mode Bytes

(Sample Values)

0x00

0x04

0x03

0x01

RFU

SENS_RES

NFCID1

SEL_RES

NFCID2

Detailed description

0xBA

0xA6

0xC9

0x89

NFCID2

FeliCa Padding Bytes

0x00

FeliCa Padding Bytes

FeliCa System Code

NFCID3 ( XOR of 0x08 and 3 bytes of

NFCID1)

0x88

0x13

General byte to be sent in

ATR_RES

Timeout Low Byte

Timeout High Byte

Number of G bytes in ATR_RES

CLOUD 45

0 F R

EFERENCE

ANUAL

Output Buffer:



Initiator Mode : On successful detection of target, the entire ATR_RES buffer from the target device would be given to the host computer



Target Mode : On successful detection by the initiator the entire ATR_REQ buffer from the initiator device would be given to the host computer



Reader Mode : The output buffer would be empty



Get Current Mode : A single byte response indicating the currently selected mode as described below o 0x00

=> P2P Initiator mode o 0x01

=> P2P Target mode o 0x02

=> Reader / Writer mode

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.14. CNTLESS_P2P_TARGET_RECEIVE

This Escape command is used to receive data from the initiator device. Prior to using this command, the device should have been successfully switched to target mode using

CNTLESS_P2P_SWITCH_MODES (E9) .

Input Buffer:

Offset

0xEA

Description Detailed description

Target Receive

RFU

0 - No Chaining

1 - Chaining

RFU

Chaining byte

Timeout Low Byte

Timeout High Byte

Output Buffer:

On successful reception, the entire data from the initiator device would be returned from offset

0x04

Offset

Offset 4 to offset 4+N

Description

– No Chaining

– Chaining

N data bytes

RFU

Chaining

Detailed description

Bytes Received.

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.15. CNTLESS_P2P_TARGET_SEND

This Escape command is used to send data to an initiator device. Prior to using this command, the device should have been successfully switched to target mode using

CNTLESS_P2P_SWITCH_MODES (E9) .

Input:

Offset

0xEB

0x00

Description Detailed description

Target Send

RFU

0x00

0 - No Chaining

1 - Chaining

RFU

Chaining byte

Timeout Low Byte

Timeout High Byte

Offset 7 to offset 7+N

Output:

Once the data bytes are sent successfully, the firmware would indicate if it is ready to send more bytes through the chaining byte

Offset

N data bytes

Description

Bytes to be sent to Initiator device

RFU

Detailed description

3 0

– No Chaining

– Chaining

RFU

Chaining

6.3.4.16. CNTLESS_P2P_INITIATOR_DESELECT

This escape command is used by the application to deselect the target device towards the end of P2P communication.

Input

Byte0

Escape code(0xE6)

Output

The deselect response as received from the target will be sent in the response buffer from offset 0x00

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.17. CNTLESS_P2P_INITIATOR_TRANCEIVE

This Escape command is used to send data to a target device. Prior to using this command, the device should have been successfully switched to initiator mode using

CNTLESS_P2P_SWITCH_MODES (E9) .

Input:

Offset

0xE7

0x00

Description Detailed description

Initiator transceive

RFU

0x00

– No Chaining

– Chaining

RFU

Chaining

Timeout Low Byte

Timeout High Byte

Offset 7 to

7+N

Output:

On successful reception of data from the target, the entire data would be available from offset

0x04. Presence of additional data is indicated by the chaining byte.

Offset

Offset 4 to offset 4+N

N bytes of data

Description

– No Chaining

– Chaining

N data bytes

Bytes to be sent to target device

RFU

Chaining

Detailed description

Bytes Received.

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.18. CNTLESS_NFC_SINGLESHOT

This Escape command is used to switch the device to Single-shot mode.

Input:

Offset Description Detailed description

0xEC

0x01

NFC Single-shot

NFC_DEP supported.

If a value other than 0x01 is given,

NFC_DEP is not supported in the preceding I-Blocks.

Output:

Output buffer

NULL

6.3.4.19. CNTLESS_NFC_LOOPBACK

This Escape command is used to switch the device to Loop-back mode.

Input:

Offset

0xED

0x01

Description Detailed description

NFC Loop-back

NFC_DEP supported.

If a value other than 0x01 is given,

NFC_DEP is not supported in the preceding I-Blocks.

Output:

Output buffer

NULL

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.20. CNTLESS_GET_SET_NFC_PARAMS

This Escape command is supported through the READER_GENERIC_ESCAPE command.

During NFC operation, number parameters like DID, LRi, PSL_REQ_BRS and PSL_REQ_FSL can be controlled from application.

Input:

To set the parameters the command syntax is:

Byte0

CLA

Byte1

INS

Byte2

Byte3

Byte4

Byte5 Byte6 Byte7

0xFF 0x70 0x04 0xE6 0x04

0x04

(opcode)

To get the parameters the command syntax is:

0x01

–

SET

NFC

Parameter

Byte0

CLA

Byte1

INS

Byte2

Byte3

Byte4

Byte5 Byte6

Byte 8

Value

Byte7

0xFF 0x70 0x04 0xE6 0x03

0x04

(opcode)

The value of byte 7 is interpreted from this table

Byte 7 Value

0x00

– DID

0x01

– LRi

0x02

– PSL_REQ_BRS

0x03

– PS_REQ_FSL

0x00

– GET

Description

Device Identification Number

Length Reduction field

BRS used in PSL_REQ

FSL used in PSL_REQ

NFC

Parameter

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.4.21. CNTLESS_GET_P2P_EXTERNAL_RF_STATE

This Escape command is supported through the READER_GENERIC_ESCAPE message.

This command is used to check if external RF is reset after the reader got detected in target mode.

Input:

Byte0

CLA

Byte1

INS

Byte2

Byte3

Byte4

Byte5 Le

0xFF 0x70 0x04 0xE6 0x01 0x06 (opcode) 00

Output:

If the command is successful, a single byte is returned. This byte indicates the value of parameter.

Bit 0 => Set to logic 1, when a present external RF field is switched off

Bit 1 => Set to logic 1, when an external RF field is detected.

Bit 2 to Bit 7 => RFU bits always read as 0

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5. Specific for Contact Interface

ESCAPE COMMAND

CONTACT_GET_SET_PWR_UP_SEQUENCE

CONTACT_EMV_LOOPBACK

CONTACT_EMV_SINGLEMODE

CONTACT_EMV_TIMERMODE

CONTACT_APDU_TRANSFER

CONTACT_DISABLE_PPS

CONTACT_EXCHANGE_RAW

CONTACT_GET_SET_CLK_FREQUENCY

CONTACT_CONTROL_ATR_VALIDATION

CONTACT_GET_SET_MCARD_TIMEOUT

CONTACT_GET_SET_ETU

CONTACT_GET_SET_WAITTIME

CONTACT_GET_SET_GUARDTIME

CONTACT_READ_INSERTION_COUNTER

Escape code

0x04

0x05

0x06

0x07

0x08

0x0F

0x10

0x1F

0x88

0x85

0x80

0x81

0x82

READER_ESCAPE_GENERIC (0x00)

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.1. CONTACT_GET_SET_PWR_UP_SEQUENCE

This Escape command is used to get or set the following parameters:



Smart card Power-on sequence



Delay between successive Activation retires



Enable/Disable any Voltage Class

As soon as card insertion is detected and Power ON message is received from the host, the firmware will start Activation with the configured voltage sequence. If the Activation fails, it will wait for the configured Activation delay and then retry with the next enabled Voltage class. If power up succeeds at an operating voltage, the firmware will continue card communication at that voltage. If power up fails in all the enabled operating voltages, then the firmware will report an error.

Input:

The first byte of the input buffer will contain the escape code. The next byte shall contain the function to be performed. Third byte shall contain the parameter for the function.

Byte0

Byte1

Value Description

0x00

0x01

Starts with Class C voltage.

(1.8V

– 3V – 5V order)

Starts with Class A voltage.

(5V

– 3V – 1.8V order)

Byte2

Escape code(0x04)

0x08 Time delay between resets

0x09

0xFE

0xFF

Delay value in milliseconds

Bit Map of all Voltage Classes

[Bit0

– Class A; Bit1 – Class B;

Bit2

– Class C]

Enable/Disable a Voltage

Class

Set bit to enable the Voltage class

Clear bit to disable the Voltage class

Retrieves all the Activation

Configuration

Retrieves the current Power up sequence

CLOUD 45

0 F R

EFERENCE

ANUAL

Output:

For retrieving all settings (0xFE), the output will be:

Byte0

Value Description

Byte 1 Byte2

0x00

0x01

Starts with Class C voltage.

(1.8V

– 3V – 5V order)

Time delay between resets in milliseconds

Starts with Class A voltage.

(5V

– 3V – 1.8V order)

Bit Map of all Voltage

Classes

[Bit0

– Class A; Bit1 –

Class B; Bit2

– Class C]

For retrieving current Power up sequence (0xFF), the output will be:

Byte0

Value Description

0x00

Starts with Class C voltage. (1.8V

– 3V – 5V order)

0x01

Starts with Class A voltage. (5V

– 3V – 1.8V order)

6.3.5.2. CONTACT_EMV_LOOPBACK

This Escape command lets the host force the firmware to perform an EMV Loop-back application.

Input:

The input buffer contains the escape code value.

Byte0

Escape code(0x05)

Output:

Output buffer

NULL

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.3. CONTACT_EMV_SINGLEMODE

This Escape command lets the host perform a one-shot EMV Loop-back application as specified in the EMV Level 1 Testing Requirements document.

Input:

Byte0

Escape code(0x06)

Output:

Output buffer

NULL

6.3.5.4. CONTACT_EMV_TIMERMODE

This Escape command lets the host perform a timer mode EMV Loop-back application as specified in the EMV Level 1 Testing Requirements document

Input:

The input buffer contains the escape code value.

Byte0

Escape code(0x07)

Output:

Output buffer

NULL

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.5. CONTACT_APDU_TRANSFER

This Escape command exchanges a short APDU with the smart card. The user has to ensure that a card is inserted and powered before issuing this Escape command.

This Escape command mostly is used by the MCard API to access synchronous memory cards.

Input:

The input buffer contains the Escape code value followed by the short APDU to be sent to the card.

Byte0

Escape code(0x08)

Byte1 onwards

Short APDU to be sent to card

Output:

Output buffer

Response APDU

6.3.5.6. CONTACT_DISABLE_PPS

This Escape command disables PPS done by the firmware/device for smart cards. This setting will take effect from the next card connect and remains effective till it is changed again or the next Reader power on. Default mode is PPS enabled.

Input:

The first byte of the input buffer contains the Escape code and the following byte, if 1 disables

PPS and if 0 enables PPS.

Byte0 Byte1

Escape code(0x0F) PPS control byte (1-DISABLES PPS, 0-ENABLES PPS)

Output:

Output buffer

NULL

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.7. CONTACT_EXCHANGE_RAW

This Escape command can be used to perform raw exchange of data with the card. The user must ensure that a card is inserted and powered on before issuing this Escape command. The

Card is deactivated upon any reception error.

Input:

The input buffer for this command contains the Escape code, low byte of the length of data to be sent, high byte of length of data to be sent, low byte of the length of expected data, high byte of length of expected data and the command.

Byte0

Escape code(0x10)

Byte1 Byte2

LSB of send length

MSB of send length

Byte3 Byte4 Byte 5 onwards

LSB of expected length

MSB expected length of Raw data to the card

Output:

Output buffer

Response APDU

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.8. CONTACT_GET_SET_CLK_FREQUENCY

This Escape command is used to instruct the reader to change the clock for the smart card or to get the current Clock divisor used. Once set, the change in frequency will take effect immediately. Default divisor value is 10, that is 4.8MHz.

Input:

The first byte of the input buffer contains the Escape code; the next byte contains the clock divisor value to set the clock frequency or 0xFF to get the clock frequency.

Byte0 Byte1

Value Description

Escape code(0x1F) Clock divisor The value to be Set in the smartcard CLK divisor register

0xFF Get current Clock divisor value

Output:

Set clock frequency: None

Get clock frequency: One byte value indicating the current Clock divisor.

Output buffer

NULL or current divisor

Clock Divisor values:

DIVISOR VALUE SCCLK Frequency

12 4 MHz

4.8 MHz

6 MHz

6.8 MHz

8 MHz

9.6 MHz

12 MHz

16 MHz

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.9. CONTACT_CONTROL_ATR_VALIDATION

This Escape command is used to enable or disable the ATR validation by the firmware in

ISO/IEC 7816 mode.

In case the card would emit an ATR that is not ISO/IEC 7816 compliant, the card reader may fail to power up the card. In these cases, disabling ATR validation will let you work with the card regardless of ISO conformity of the ATR.

By default, ATR validation is enabled.

Input:

The first byte of the input buffer will contain the Escape code; the next byte will contain the control byte.

Byte0 Byte1

Escape code(0x88)

Value Description

0x00 Enable ATR validation

0x01 Disable ATR validation

Output:

Output buffer

NULL

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.10. CONTACT_GET_SET_MCARD_TIMEOUT

This Escape command is used to get or set the delay which is applied after a Write operation to memory cards. The delay is specified in milliseconds.

Input:

The first byte of the input buffer will contain the Escape code; the next byte will contain the memory card write delay in seconds.

Byte0 Byte1

Value Description

Escape code(0x85)

0x01 Delay in milliseconds for memory card Write

Any value other than

Read the current applied delay for memory card

Write

Output:

Write delay: No response byte

Read delay value: A byte value specifying the current delay applied during memory card Write in milliseconds

Byte0

Null or

Delay in ms

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.11. CONTACT_GET_SET_ETU

This Escape command is used by the HOST to get/set the current ETU for smart cards. Once set, the new ETU value will take effect immediately.

Input:

The input buffer contains the Escape code followed by an 8 bit GET/SET identifier. For SET

ETU, a DWORD specifying the value to be set is following.

Byte0 Byte1

Value Description

Byte2 Byte3 Byte4

Wait time

Byte5

Escape code(0x80)

0x01 SET ETU BIT31-

BIT24

0x00 GET ETU -

Output:

For both Set and Get ETU, the output will be the following.

Byte0 Byte1

ETU value

Byte2 Byte3

BIT31-BIT24 BIT23-BIT16 BIT15-BIT8 BIT7-BIT0

BIT23-

BIT16

BIT15-

BIT8

BIT7-

BIT0

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.12. CONTACT_GET_SET_WAITTIME

This Escape command is used to get/set the Character/Block Waiting Time for smartcards. The wait time is specified in terms of ETU. Once set, the new Wait time will take effect from the next card communication.

Input:

The input buffer contains the Escape code followed by an 8 bit GET/SET identifier, an 8 bit

Wait time identifier and a 32 bit Wait time value. BWT must be specified in units of 1.25ms and

CWT in units of ETU.

Byte0

Escape code(0x81)

Byte1 Byte2

CWT

BWT

Byte3 Byte4 Byte5

Value Description Value Description

0x01 SET time

Wait 0x00

0x01

CWT

BWT

BIT31-

BIT24

Wait time in ETU

BIT23-

BIT16

BIT15-

BIT8

BIT7-

BIT0

0x00 GET Wait time

0x00

0x01

- - - -

Byte6

Output:

For both Get/Set Wait time, the output will be the following.

Byte0 Byte1 Byte2

Wait time in ETU

Byte3

BIT31-BIT24 BIT23-BIT16 BIT15-BIT8 BIT7-BIT0

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.13. CONTACT_GET_SET_GUARDTIME

This Escape command is used to get/set the Character/Block Guard Time of the reader. The guard time is specified in terms of ETU. Once set, the new Guard time will take effect immediately.

Input:

The input buffer contains the Escape code followed by an 8 bit GET/SET identifier, an 8 bit guard time identifier and a 32 bit guard time value in ETU.

Byte0

Escape code(0x82)

Byte1 Byte2

Value Description Value Description

0x01 SET Guard time

0x00

0x01

CGT

BGT

Byte3 Byte4 Byte5 Byte

BIT31-

BIT24

Guard time in ETU

BIT23-

BIT16

BIT15-

BIT8

BIT7-

BIT0

- 0x00 GET Guard time

0x00

0x01

CGT

BGT

- -

Output:

For Get/Set guard time, the output will be the Character/Block Guard Time value.

Byte0

Character Guard time in ETU

BIT31-BIT24

Byte1

BIT23-BIT16

Byte2

BIT15-BIT8

Byte3

BIT7-BIT0

CLOUD 45

0 F R

EFERENCE

ANUAL

6.3.5.14. CONTACT_READ_INSERTION_COUNTER

This Escape command is supported through the READER_GENERIC_ESCAPE command and

retrieves the number of times a contact smart card has been inserted into the reader.

Input:

The first five bytes of the input buffer follow APDU structure as per [PCSC3-AMD1]. The 6 th byte is the Escape code 0x00 to identify the command.

Byte0 Byte1 Byte2 Byte3 Byte4 Byte5

0xFF 0x70 0x04 0xE6 0x01

0x00

(Escape code)

Output:

4 (Insertion counter is a 4 byte value)

Byte0 Byte1 Byte2 Byte3 Byte4 Byte5

Insertion counter value SW1 SW2

BIT31-BIT24 BIT23-BIT16 BIT15-BIT8 BIT7-BIT0 0x90 0x00

In case of any error, only SW1 and SW2 set with error status will be returned.

CLOUD 45

0 F R

EFERENCE

ANUAL

7. Mechanical Integration

7.1. Module Mounting Holes, HF Antenna and LED

Details

Figure 1 locates the 5 mounting holes. All mounting holes have a diameter of 3.0mm.

The mounting hole called H5 provides the possibility to ground the PCBA. The LED dimension is L3.2mm x W2.8mm x H1.9mm. The LED is bi color Yellow green and RED.

NOTE: CLOUD4500F & CLOUD 4510F TOP SIDE VIEW ARE SAME

Figure 1

– CLOUD 4500F & 4510F MODULE TOP SIDE VIEW DETAILS

CLOUD 45

0 F R

EFERENCE

ANUAL

7.2. CLOUD 4500F USB Interface and Smart Card

Connector Details

Connector Description Reference-Part No.

USB

CLOUD4500F

Smart Card

Default Molex 5-pin connector

Part No. 53325-0560

Optional: mini-B connector MOLEX 54819-0572

Default: Friction contact

Hamburg ICA-602

Optional: Landing contact

Hamburg ICA-703

Pin 1

USB receptacle

ICA 602

ICA-703

Friction or

Landing

Connector

Figure 2 - CLOUD 4500F MODULE BOTTOM VIEW

100.000 insertion cycles typ.

500.000 insertion cycles typ.

CLOUD 45

0 F R

EFERENCE

ANUAL

Figure 2 shows, how the ID1 smart card extends out of the module when it is fully inserted into the connector.

Note: Both Friction and Landing Connector are exactly same in dimensions

Figure 3 shows the same in side view, dimensions not to scale

Figure 3 - CLOUD 4500F SIDE VIEW MODULE - SMART CARD DETAILS

Figure 4 shows the details of Smart Card Connector from connector vendor. The Measurement is same for Landing or Friction Type Connector.

Figure 4 - Friction or Landing Type Smart Card Connector Details

CLOUD 45

0 F R

EFERENCE

ANUAL

7.3. CLOUD 4510F USB Interface and SAM Card

Connector Details

Connector Description Reference-Part No.

USB

CLOUD4510F

SAM Card

Default Molex 5-pin connector

Part No. 53325-0560

Optional: mini-B connector MOLEX 54819-0572

Default: Open/Close Type Hamburg ICA-560

Pin 1

USB receptacle

SAM card connector, toploading

Figure 5- CLOUD 4510F MODULE BOTTOM SIDE VIEW

7.4. Module thickness

CLOUD 4500F

–SMART CARD CONNECTOR MODULE TOTAL THICKNESS 10.91mm

CLOUD 45

0 F R

EFERENCE

ANUAL

Figure 6- CLOUD 4500F MODULE THICKNESS DETAILS

CLOUD 4510F

– SAM CONNECTOR MODULE TOTAL THICKNESS 9.98mm

Figure 7- CLOUD 4510F MODULE THICKNESS DETAILS

CLOUD 45

0 F R

EFERENCE

ANUAL

7.5. General recommendations

7.5.1. Smart Card Insertion

To avoid damage of the smart card connector due to improper card insertion, it is recommended that the housing mechanics around the CLOUD 4500 F module provide good horizontal and vertical guidance to the card. Objective is that even when the card is inserted with a certain angle, it is guided towards J4 without any blocking points.

A housing/mounting environment for the CLOUD 4510 F should be designed such, that the toploading connector for the SAM will be accessible to be opened and a card can be inserted.

7.5.2. Contactless Reading

In order to provide optimum contactless reading distance the following recommendations should be followed:

The module top surface must be placed as close as possible to the front bezel of the casing you design.

The casing you design should provide a landing area that invites the user to place his/her credential centered on the HF antenna area (see figure 1)

Avoid any metal plate in the area of the HF antenna. Metal planes detune the antenna and can even make the module not function at all.

It is recommended for proper communication, that a minimum distance of 2.5cm (1”) will be kept to metallic objects. No metallic objects should be present between antenna and card.

To prevent the fields of adjacent readers to interfere with each other, a minimum distance between readers of 2.5cm (1”) should be kept.

The minimum distance between antenna and card should not be less than 5mm (0.2”).

8. Electrical integration recommendations

8.1. USB connector and Cable specification

This module has USB Connection interface using Molex Part No. 53325-0560.

To connect with above Receptacle Connector, Plug of Molex 51090-0500 housing and Molex

50212-0800 Crimp Terminal can be used.

The Wire Connections of USB [Molex] Connector is shown below.

PIN NUMBER

WIRE COLOR

RED

SIGNAL NAME

VBUS

– [ D MINUS]

WHITE

GREEN D + [ D PLUS ]

BLACK GND

SHEILD [ DRAIN+BRAID] SHEILD GND

Identive recommends using USB 2.0 certified cables. The length of the cable should be limited to 1.5 meter maximum, with 28 AWG# 1P, 28 AWG# 2C specifications.

CLOUD 45

0 F R

EFERENCE

ANUAL

8.2. ESD and EMI recommendations

Depending on your mechanical design, the LED may be an ESD injection channel. Identive recommends that, your casing integrates a light pipe that creates a gap of at least 7mm on top of the LED surface

The ISO7816 contacts have been tested to resist +/-4KV [HBM Model] contact ESD discharge.

Beyond this value, the microcontroller may be reset. If your application has higher ESD resistance requirements, we recommend that, you consider adding brushes connected to ground on the card slot to discharge charges, which may be carried by smart cards.

Identive used Ferrite core on Cable for FCC Certification. As per your requirement and environmental conditions you can choose appropriate Ferrite Core.

CLOUD 45

0 F R

EFERENCE

ANUAL

9. Annexes

9.1. Annex A

– Status words table

SW1 SW2 Description

0x90 0x00 NO ERROR

0x63

0x65

0x67

0x68

0x6A

0x6B

0x6D

0x6E

0x6F

0x00

0x81

0x00

0x81

0x00

NO INFORMATION GIVEN

MEMORY FAILURE

LENGTH INCORRECT

CLASS BYTE INCORRECT

FUNCTION NOT SUPPORTED

WRONG PARAMETER P1-P2

INVALID INSTRUCTION BYTE

CLASS NOT SUPPORTED

UNKNOWN COMMAND

CLOUD 45

0 F R

EFERENCE

ANUAL

9.2. Annex B

– Sample code using escape commands

File Name: CLOUD 45x0 F Escape.h

#ifndef _CLOUD_45x0F_ESCAPE_H_

#define _CLOUD_45x0F_ESCAPE_H_

#ifdef __cplusplus extern "C" {

#endif

#pragma pack (1) typedef struct

{

BYTE byMajorVersion;

BYTE byMinorVersion;

BYTE bySupportedModes;

WORD wSupportedProtocols;

WORD winputDevice;

BYTE byPersonality;

BYTE byMaxSlots;

BYTE bySerialNoLength;

BYTE abySerialNumber [28];

} ReaderInfoExtended;

#pragma pack ()

#define IOCTL_CCID_ESCAPE SCARD_CTL_CODE (0xDAC)

#define READER_SET_MODE 0x01

#define READER_GET_MODE 0x02

#define READER_GETIFDTYPE 0x12

#define READER_LED_CONTROL 0x19

#define READER_LED_CONTROL_BY_FW 0xB2

#define READER_GETINFO_EXTENDED 0x1E

#define READER_RDWR_USR_AREA 0xF0

#define CONTACT_GET_SET_POWERUPSEQUENCE 0x04

#define CONTACT_EMV_LOOPBACK 0x05

#define CONTACT_EMV_SINGLEMODE 0x06

#define CONTACT_EMV_TIMERMODE 0x07

#define CONTACT_APDU_TRANSFER 0x08

#define CONTACT_CONTROL_PPS 0x0F

#define CONTACT_EXCHANGE_RAW 0x10

#define CONTACT_GET_SET_CLK_FREQUENCY 0x1F

#define CONTACT_GET_SET_ETU 0x80

#define CONTACT_GET_SET_WAITTIME 0x81

#define CONTACT_GET_SET_GUARDTIME 0x82

#define CONTACT_GET_SET_MCARD_TIMEOUT 0x85

#define CONTACT_CONTROL_ATR_VALIDATION 0x88

#define CNTLESS_GETCARDINFO 0x11

#define CNTLESS_GET_ATS_ATQB 0x93

#define CNTLESS_CONTROL_PPS 0x99

#define CNTLESS_RF_SWITCH 0x96

#define CNTLESS_SWITCH_RF_ON_OFF 0x9C

#define CNTLESS_GET_BAUDRATE 0x9E

#define CNTLESS_CONTROL_RETRIES 0xA7

#define CNTLESS_CONTROL_POLLING 0xAC

#define CNTLESS_GET_CARD_DETAILS 0xDA

#define CNTLESS_SET_CONFIG_PARAMS 0xE1

#define CNTLESS_IS_COLLISION_DETECTED 0xE4

#define CNTLESS_FELICA_PASS_THRU 0xF3

#define CNTLESS_P2P_SWITCH_MODES 0xE9

#define CNTLESS_P2P_TARGET_RECEIVE 0xEA

#define CNTLESS_P2P_TARGET_SEND 0xEB

#define CNTLESS_P2P_INITIATOR_TRANSCEIVE 0xE7

#define CNTLESS_NFC_SINGLESHOT 0xEC

#define CNTLESS_NFC_LOOPBACK 0xED

#ifdef __cplusplus

}

#endif

CLOUD 45

0 F R

EFERENCE

ANUAL

File Name: CLOUD 45x0 F Escape.c

#include <windows.h>

#include <winbase.h>

#include <stdio.h>

#include <conio.h>

#include "winscard.h"

#include "winerror.h"

#include "CLOUD 45x0F Escape.h"

VOID main(VOID)

{

SCARDCONTEXT ContextHandle;

SCARDHANDLE CardHandle;

ReaderInfoExtended strReaderInfo;

BYTE InByte, i;

DWORD

ULONG char char

BytesRead, ActiveProtocol; ret;

*s;

*ReaderName[] = {"Identive CLOUD 4500 F Contact Reader 0",

"Identive CLOUD 4500 F Contactless Reader 0",

NULL};

/***************************************************************************************

*****************/

ContextHandle = -1; ret = SCardEstablishContext(SCARD_SCOPE_USER, NULL, NULL, &ContextHandle); if (ret == SCARD_S_SUCCESS)

{ s = ReaderName[0]; printf("Connecting to reader %s\n", s); ret = SCardConnect( ContextHandle, s,

SCARD_SHARE_DIRECT,

SCARD_PROTOCOL_UNDEFINED,

&CardHandle,

&ActiveProtocol); if (ret == SCARD_S_SUCCESS)

{

InByte = 0x1E; ret = SCardControl( CardHandle,

IOCTL_CCID_ESCAPE,

&InByte,

&strReaderInfo, sizeof(strReaderInfo),

&BytesRead); if (SCARD_S_SUCCESS == ret) { printf("major version:\t\t%d%d\n", (strReaderInfo.byMajorVersion& 0xF0)>> 4,

(strReaderInfo.byMajorVersion& 0x0F)); printf("minor version:\t\t%d%d\n", (strReaderInfo.byMinorVersion& 0xF0)>> 4,

(strReaderInfo.byMinorVersion& 0x0F)); printf("modes:\t\t\t%d\n", strReaderInfo.bySupportedModes); printf("protocols:\t\t%04x\n", strReaderInfo.wSupportedProtocols); printf("input device:\t\t%04x\n", strReaderInfo.winputDevice); printf("personality:\t\t%d\n", strReaderInfo.byPersonality); printf("maxslots:\t\t%d\n", strReaderInfo.byMaxSlots); printf("serial no length:\t%d\n", strReaderInfo.bySerialNoLength); printf("serial no:\t\t"); for (i = 0; i <strReaderInfo.bySerialNoLength; i++) if (strReaderInfo.abySerialNumber[i] != 0) printf("%c", strReaderInfo.abySerialNumber[i]);

} else { printf("SCardControl failed: %08X\n", ret);

}

} else { printf("SCardConnect failed: %08X\n", ret);

}

CLOUD 45

0 F R

EFERENCE

ANUAL

ret = SCardReleaseContext(ContextHandle);

} else

{ printf("\n SCardEstablishContext failed with %.8lX",ret);

} printf("\npress any key to close the test tool\n"); getch();

}

100

Annonce

Identive Infrastructure

Reference Manual

– version 1.0

Dual Interface Smartcard Reader Modules

Reference manual

CLOUD 45x0 F Dual Interface Smartcard Reader

Modules

Document history

Contact information

Table of Contents

1. Legal information

1.1. Disclaimers

1.2. Licenses

1.3. Trademarks

2. Introduction to the manual

2.1. Objective of the manual

2.2. Target audience

2.3. Product version corresponding to the manual

2.4. Definition of various terms and acronyms

2.5. References

2.6. Conventions

3. General information about CLOUD 45x0 F

3.1. CLOUD 45x0 F key benefits

3.2. CLOUD 45x0 F key features

3.3. CLOUD 45x0 F ordering information

3.4. CLOUD 45x0 F customization options

3.5. Contactless communication principles and CLOUD

45x0 F usage recommendations

3.6. Applications

4. CLOUD 45x0 F characteristics

4.1. CLOUD 45x0 F high level architecture

4.2. Quick reference data

5. Software modules

5.1. Installation

5.2. Utilities

5.3. Driver

5.4. Firmware

6. Commands description

6.1. Generic APDU

6.2. Supported Pseudo APDU (Contactless Interface)

XX SW1 SW2

00 90 00

XX 62 82

XX 63 00

XX 63 01

XX 6A 81

XX 67 00

XX 6A 80

XX 64 00

XX 64 01

XX 6F 00

XX = number of the bad data object in the APDU;

00 = general error of APDU;

01 = error in the 1

data object;

02 = error in the 2

data object; etc.

No error occurred

Data object XX warning, requested information not available

No information.

Execution stooped due to failure in other data object

Data object XX not supported

Data object XX with unexpected length

Data object XX with unexpected vale

Data Object XX execution error (no response from IFD)

Data Object XX execution error (no response from ICC)

Data object XX failed, no precise diagnosis

6.3. Escape commands for the CLOUD 45x0 F

7. Mechanical Integration

7.1. Module Mounting Holes, HF Antenna and LED

Details

7.2. CLOUD 4500F USB Interface and Smart Card

Connector Details

7.3. CLOUD 4510F USB Interface and SAM Card

Connector Details

7.4. Module thickness

7.5. General recommendations

8. Electrical integration recommendations

9. Annexes

9.1. Annex A