INSTALLATION / USER MANUAL
NFCReader module
HEY YOU,
LET ME
HELP!
Share, inspire, have fun!
With CTOUCH by your side.
CONTENT
Preparing for installation................................................................................................................................3
Install the NFC software................................................................................................................................3
Register cards.......................................................................................................................................................5
Errors messages.................................................................................................................................................6
Detailed information for personalized setup.....................................................................................6
2
Share, inspire, have fun!
With CTOUCH by your side.
NFCReader module
PREPARING FOR INSTALLATION
Download the zip-file from our support
center.
Open the zip-file.
Extract the file from the downloaded
zip-file.
3
INSTALL THE NFC SOFTWARE
Click on the CTOUCH NFC installer icon to
start the installation.
Click on ‘Install’.
Wait until the installation is completed.
Click on ‘Next >’.
Click on ‘Next >’
Click on ‘Next >’
a
See chapter 4 for more explanation
about these fields.
a
See chapter 5 for more explanation
about these fields.
ctouch.eu
Click on ‘Next >’
a
See chapter 5 for more explanation
about these fields.
Click on ‘Next >’
a
Click on ‘Next >’
Make sure you keep the setting on
‘Everybody’. If you change it, the
NFC software will only work for
that specific user.
4
Wait till the installation is finished.
Share, inspire, have fun!
With CTOUCH by your side.
Click on ‘Close’ to exit the installer.
Click on ‘Close’ to exit the installer.
NFCReader module
REGISTER CARDS
Below you will find the steps you will go through when creating an NFC card
successfully. Please look at Step 4 for the possible errors you might encounter. In
chapter 5 you can find the customization options.
Click on the NFC Registration icon
Allow this app to run as administrator by
clicking on ‘Yes’.
Your now presented with the NFC reader
application.
5
Fill in the credentials of the computer
user you want to create an NFC card for.
If you want to see the entered password,
tick the tick box to show the information.
Click on continue.
Wait till the validation is completed.
Place a new NFC-card against the card
reader.
The card has been written successfully.
a. Click on ‘another’ to write another
card or click on ‘close’ to close the
application.
ctouch.eu
ERRORS MESSAGES
During the process of creating NFC cards some errors may occur. Below you will find an
overview of the possible errors you can get and the solution.
If you filled in the wrong credentials, the
filled in credentials will be marked red.
You need to fill in the correct credentials
to continue.
When no card was presented to the NFC
module within the 10 seconds time frame,
the following message will be shown.
Click on Try Again and place an NFC card
against the NFC module, within the given
time frame.
When you use an NFC card which is not
the right type of NFC card, the following
message will be shown. Make sure you
use NFC cards which are compatible with
the CTOUCH NFC reader/writer module.
Please see the tech data sheet for these
details.
If the required sector on the presented
card is already in use, the following
message will appear. Try to move the
content on that sector or reinstall the NFC
software to change the sector which is
being written to.
If you remove the card too early, the
following message will be shown.
Click on Try Again and place the NFC
card against the reader again. Keep it
there until the card has been written
successfully.
6
a. See chapter 5 for more information
about sectors.
DETAILED INFORMATION FOR PERSONALIZED SETUP
During the installation you can change the settings of the NFC software, customize your
NFC cards and protecting it even further. Please find the settings you can change below.
NFC Reader/Writer Port
Settings about the USB-port which is
used for the NFC module.
The default value is 100. Do not change
this setting!
NFC Reader/Writer Baud
The speed which is used to communicate
between the display and the NFC module.
The default value is 0. Do not change this
setting!
Share, inspire, have fun!
With CTOUCH by your side.
NFCReader module
NFC storage sector M1 NFC cards
This indicates the sector on which the required information is being saved onto the
NFC card. It is advised not to change the sector, only if you will use the cards for other
purposes who are using the same sector. The default value is 0.
For the CTOUCH NFC card you can choose a sector between 0 and 15. If you will use
another NFC card, you need to look at the specification of the NFC card you are using
which sectors are available.
Encryption Key (block 1)
The first block out of two blocks which is needed to save the key onto the NFC card.
You can fill in the following blocks:
NFC Storage Sector 0 = block 1 or 2.
NFC Storage Sector 1 till 15 = block 0, 1 or 2.
Please note: if you have selected NFC Storage Sector 0, you cannot choose 0 for this
block.
Encryption Key (block 2)
The second block out of two blocks which is needed to save the key onto the NFC card.
You can fill in the following blocks:
NFC Storage Sector 0 = block 1 or 2.
NFC Storage Sector 1 till 15 = block 0, 1 or 2.
Please note: if you have selected NFC Storage Sector 0, you cannot choose 0 for this
block.
NFC DESfire master key
The key with which the DESfire card is
encrypted. We advise you to change the
default master key. The default size is 16
numbers of a maximum of 3 characters
per number.
NFC DESfire key number
The ID of the DESfire master key. The
default value is 0.
NFC Application id
The ID of the login application. One card
can support multiple Applications (or
purposes). To make a distinction between
the application, you can use this ID. The
default value is 0, 0, 1.
NFC Credential file id
The ID of the file in which the log-in
details are being saved. The default value
is 1.
Sector Protection Key
This key can be changed in order to create your own personalized Sector Protection
Key. This means that the sector on the card, which is being used to write the content
to, is being protected with your own personal Sector Protection Key. We advise you to
change the Sector Protection Key.
You need to fill in 6 numbers between 1 and 255. Please note that this key needs to be
the same on all the devices, on which you want to have access to with your NFC cards.
ctouch.eu
7
1682V210809 EN
Share, inspire, have fun!
With CTOUCH by your side.
ctouch.eu
">
