Mitsubishi PLK-E sewing machine Technical Manual

Industrial Sewing Machine

TECHNICAL MANUAL

Electronic Pattern Sewing Machine

PLK-E Series

Control Unit Section

A180E483P03

Contents

[1] For safe use

[2] Precautions for use

[3] Installation

[4] Names of each part, wiring and grounding

[5] Confirmation

[6] Using the floppy disk

[7] System installation method

[1]-1

[2]-1

[3]-1

[4]-1

[5]-1

[6]-1

[7]-1

[8] Operating the setting panel keys

[9] Basic mode operation

[8]-1

[9]-1

[10] Customized input/output

[10]-1

[11] Input/output setting mode

[11]-1

signal [11]-1

(2) signal

[12] Program mode list

[13] Error Display

[14] Unit wiring diagram

[15] Several power supply

[16] Control box connectors layout

[17] Pin No. of connectors

[18] How to use the terminal 1,2 and connectors

[19] Table of connection into control box

[20] Specifications

[21] Table of digital display

- I -

[12]-1

[13]-1

[14]-1

[15]-1

[16]-1

[17]-1

[18]-1

[19]-1

[20,21]-1

[20,21]-1

Thank you for purchasing the Mitsubishi industrial sewing machine PLK-E Series.

Please read this technical manual before starting to ensure correct and long-term use.

* The contents of this manual may not be reproduced in part or whole.

* The contents of this manual are subject to change without notice.

* An utmost effort has been made to cover all points of operation in this manual.

Contact Mitsubishi if you have any questions regarding the contents.

*COPYRIGHT(C)2001 MITSUBISHI ELECTRIC CORPORATION

- II -

For safe use

[1] For safe use

For safe use

Always observe the following matters to safely use the Mitsubishi industrial electronic sewing machine

PLK-E Series (motor and control box).

Before starting

Before using this control unit, read all of the technical manuals carefully, and correctly use the unit following the manual. Also read the "Mitsubishi Industrial Electronic Sewing Machine Manual

<<Sewing Machine Head Section>>" for details on the general configuration and sewing machine head.

Application and purpose

This control unit is designed to drive and control the Mitsubishi industrial electronic sewing machine

PLK-E Series. Do not use this control unit for other applications or purposes. Do not use this control unit until it has been confirmed that safety measures have been accurately taken for the installed electronic sewing machine head section.

Working environment

Do not use this control unit in the following type of environment.

(1) Power voltage

* Where the voltage fluctuation exceeds 10% of the rated voltage.

* Where the specified power capacity (refer to page [4]-3. 6.Power capacity) cannot be ensured.

(2) Magnetic noise

* Where strong fields or magnetic fields are generated, such as near a high-output high frequency oscillating machine or high frequency welder.

(3) Temperature and humidity

* Where the ambient temperature is 35°C or more and 5°C or less.

* Where the unit will be subject to direct sunlight, or outdoors.

* Near sources of heat, such as heating appliances.

* Where the relative humidity is 45% or less, or 85% or more, and where dew may condense.

(4) Atmosphere

* In an atmosphere containing dust or corrosive gases, etc.

* In a flammable gas or explosive environment.

(5) Vibration

* If excessive vibration could occur when installed on the sewing machine, separately install the control box.

Installation

Motor and control box

Correctly install the motor and control box according to this manual.

Accessories

Always disconnect the control unit from the main power supply before installing the accessories listed in this manual. (Turn the power switch OFF, and disconnect the plug from the socket (power supply line).)

Cable

(1) Lay the connection cables so that excessive force will not be applied during operation. Do not excessively bend the cables.

(2) Cables laid near operating machine sections (ex., pulley or V-belt) must be separated by at least

25mm.

[1]-1

For safe use

(3) Before connecting the power cable to the control box, confirm that the power voltage matches the specifications given on the control box's rating nameplate and factory shipment voltage nameplate. Connect the cable to the indicated positions, and then supply the power. When using a power unit, connect the cable to the power unit and supply the power. In addition, when using a power unit, confirm that the power voltage matches the specifications given on the power unit's rating nameplate. Turn the power switch OFF before making any connections.

Grounding

Always ground the power cord's grounding wire.

Enclosed units and accessories

Connect the electrical enclosed units and accessories only to the positions indicated in the manual.

Removal

(1) Always turn the power switch OFF and disconnect the plug from the socket (power supply line) before removing the motor or control box.

(2) Do not pull out the cord when disconnecting the plug. Always hold the plug receptacle when disconnecting the plug.

(3) Note that a high voltage is applied inside the control panel, so always turn the power OFF and

wait at least ten minutes before opening the control box cover.

Maintenance, inspection and repairs

(1) Follow this manual when carrying out maintenance or inspections related to this control unit.

(2) This unit must be repaired, serviced and inspected only by a worker that has received special training.

(3) Do not use this control unit with the ventilation holes on the dust-proof filter of the motor blocked, or clogged with dust, dirt or loose cloth, etc. (This can cause heating.)

(4) Always turn the power OFF before replacing the needle or bobbin, etc., on the head.

(5) Use genuine replacement parts for repairs and maintenance.

Other safety measures

(1) Keep fingers away from all moving machine parts (especially around the sewing machine needle or V-belt, etc.).

(2) Never drop the control unit, or place objects in the clearances.

(3) Do not operate the sewing machine without the protective parts such as the belt cover, or protection devices such as the safety breaker.

(4) If any damage is observed in the control unit, if the unit does not operate correctly, or if the operation is suspicious, always suspend operation. Only operate the machine after the supervisor has adjusted, repaired or inspected the machine.

(5) The user must not make improvements or changes without instruction from Mitsubishi.

Caution displays and danger displays

(1) This symbol indicates states hazardous to the operator or machine, and requires special caution.

(2) This symbol indicates an electrical hazard or caution (electric shock caution).

(3) This symbol indicates grounding of the ground wire.

* Always deliver this manual to the end user.

* Store this manual nearby where it can be referred to when necessary.

[1]-2

[2] Precautions for use

1. Do not place foot on the foot switch when turning the power ON.

ＯＦＦ ＯＮ

Precautions for use

2. Always turn the power OFF when leaving the sewing machine.

ＯＦＦ ＯＮ

3. Do not inspect the control circuit with a tester.

4. Always turn the power switch OFF before tilting the sewing machine head, replacing the needle, or passing thread through the needle.

Control circuit

The tester voltage could be applied on the semiconductor parts, and cause damage.

5. Always ground the grounding wire.

Power supply

6. Do not use excessive wiring.

ＯＦＦ ＯＮ

Green

(Green/yellow)

Always ground the provided grounding wire

(green(green/yellow)).

7. A high voltage is applied inside creating a hazardous state, so always turn the power OFF and wait ten minutes before opening the cover.

8. Use the machine away from strong noise sources such as high frequency welders.

Noise

High voltage risk

[2]-1

Precautions for use

9. The sewing machine will coast to a stop when the power is turned OFF or a power failure occurs during sewing machine operation.

10. Always align the connector shape and direction, and securely insert the connector.

11. If the position detector's connector dislocates, the belt dislocates, or the sewing machine is completely locked, the motor will be turned OFF automatically for a set time to prevent burning.

(Note that the motor may not turn OFF if there is incomplete locking or an overload.) When the fault has been recovered, turn the power OFF and ON once to resume normal operation. The same type of operation will take place if a detector fault or disconnection occurs.

12. Periodically remove the dust adhered on the motor's dust-proof filter once every two to three weeks.

14. If the fuse blows, remove the cause, and replace the blown fuse with one having the same capacity.

FDD

Trans- former

Dust-proof filter

Box

If operation is continued with the filter clogged, the motor could heat and adversely affect the motor life.

13. When connecting the external switch to an optional connector, etc., keep the signal wire as short as possible. A long wire could cause malfunctions.

ＰＬＫ－Ｂ１－ＰＭＤ－Ｅ

( PMD PCB )

(View from the front with cover removed)

8A fuse (one fuse)

Box

Use a shielded wire for the signal wire when possible.

ＸＣ－Ｅ２

－１Ｂ－ＰＬＫ

ＰＬＫ－Ｂ１

－ＣＰＵ－Ｅ

20A fuse (two fuses)

View from the front with the cover and PMD PCB d

[2]-2

[3] Installation

1. Installing the motor Table

Belt hole

2. Installing the pulley

Accurately tighten the pulley.

Installation

66

Correctly install the motor using the installation bolts, washers, spring washers and nuts.

Caution

* Insufficient tightening can lead to malfunctions.

* The pulley is a control box accessory.

3. Installing the protective cover (product with belt dislocation prevention part)

View from back of protective cover View from front of protective cover

Wing bolt

Washer

* Change the long and short side orientation of the installation plate for the belt dislocation prevention part to match the outer diameter of the motor pulley.

Motor pulley outer diameter phi55 to phi80

Protective cover installation thumb screw

Pulley outer

diameter o55 to 80

Indication scale

(front side)

Cross-section A-A

Installation plate

Long and short side

Ａ

(View from back of protective cover)

* Align the center of the washer with the pulley outer diameter indication scale, and tighten the wing bolt.

* Make sure that the belt does not contact the fitting.

[3]-1

Installation

4. Installing the protective rod

View from back of protective cover View from front of protective cover

Protective rod wing nut

Installation plate

Wing bolt

Protective cover installation thumb screw

Washer

Install the protective rod between the belt and motor pulley as shown below.

Belt

Protective rod

Motor pulley

Protective cover

5. Installing the control box

View from front of protective cover

* Align the center of the protective rod to the position at the center of the belt and motor pulley, and tighten the wing bolt.

* Make sure that the belt and motor pulley do not contact the protective rod.

Fix at four positions

Installation bolt

(M8×60)

Leg

Damper

Top plate

cushion

Leg

Washer

Spring washer

Nuts

Control box

**Damper

cushion

１０５ ４－φ９

* Insert the four bolts into the holes on the top plate and install the control panel.

* At this time, adjust the damper cushion positions so that the ** damper cushions listed above

(enclosed with control box) contact the legs.

[3]-2

Names of each part, wiring and grounding

[4]. Names of each part, wiring and grounding

1. Front side

LED

Floppy disk driver

Setting panel

Cover

Cover installation screw

(M4 screw)

2. Setting panel section

[↑] key

(upward arrow key) jog +

LED.1

LED.2

LED.3

LED.4

LED.5

[H] key

Home

H

F

[D] key

Read

[↓] key

(downward arrow key) jog +

[F]key

Function Program mode transition

[A]key

Speed setting

[B]key

Bobbin winding

Setting key

[C] key

Enter (message clear)

* If the input panel (option) is connected, LED 1 to 5 will not light. However, during system installation, it will light even if the input panel is connected.

[4]-1

Names of each part, wiring and grounding

3. Back side

CONA

Spindle motor power

(Connect to spindle motor)

CONB

CONC

Stepping motor

(Connect to sewing machine head stepping motor)

COND

Various solenoids

(Connect to sewing

machine head section)

CONE

RS-232C

Input panel (option)

CONG

General-purpose input/output signal

CONH

Input signal (Connect to sewing machine head section)

CONI

Foot switch

(Connect to foot switch)

: The shaded connectors indicate the standard connectors.

Thus, always connect the shaded connectors when setting up the sewing machine.

Securely connect so that a connection fault does not occur.

[4]-2

Names of each part, wiring and grounding

4. Connecting the power connector

Top plate

Control box power

Power connector

Spindle motor power connector

Control box

Note. Always confirm the connector shape and insertion orientation and completely insert the power connector into the control box.

Always turn the power OFF before connecting the connector.

5. Connecting the 3-phase power supply

3-phase power supply

R-phase S-phase T-phase

Red (black)

White (brown)

Black (blue)

Green (green/yellow)

Push-button switch cord

Always connect the green wire to the grounding terminal.

Consult with your electrician for details on the grounding wire.

6.Power capacity

Use a fuse or safety breaker on the power supply.

Power supply

Single-phase 100V

3-phase 200V

Recommended current capacity value

15A

10A

[4]-3

Names of each part, wiring and grounding

7. Using the 3-phase 200V control box with single-phase 200 to 220V

Connect power supply to the "red" and "white" lead wires for the push-button switch. The black wire is not used, so insulate it by wrapping insulation tape, etc., around it. Always ground the green grounding wire.

Connect to ground

Connection connector to control box

Push-button switch

Do not connect

(Accurately insulate with tape.)

Green

Red

White

Black

Connect these lead wires to the power supply.

8. Using the single-phase 100V control box with single-phase 110 to 120V, or using the 3-phase 200V control box with 3-phase 220 to 240V

Connector

(1) Turn the power OFF and wait at least 10 minutes.

(2) Remove the cover.

(3) Interchange CON5 and CON6 on the XC-B2-1B-2005 PCB.

Floppy disk driver

FDD

For single-phase

110V to 120V

3-phase 220V to

CON6 From transformer

CON5

From PLK-B1-PMD

PCB CON1

For single-phase 100V

3-phase 200V

CON6

From PLK-B1-PMD PCB

CON1

CON5 From transformer

XC-B2-1B

-2005

Trans- former

PLK-B1

-CPU

PLK-B1PMD

PLK-B1-PMD

PCB CON1

Control box

[4]-4

[5] Confirmation

1. Before turning the switch ON

Confirmation items

(1) Are the power and capacity correct?

(2) Are the connectors correctly inserted?

* Power connector from push-button switch

* Motor connector

* Motor encoder connector

* Foot switch connector

* Other connectors (option, input panel, etc.)

(3) Is the belt tension correct?

(4) Are the pulley nuts securely tightened?

(5) Can the sewing machine be easily rotated by hand?

2. After turning the switch ON

(1) Does the position detector lamp turn ON?

Position detector lamp

(2) Does the control box setting panel section LED turn ON?

Control box setting panel section LED

(3) Is there any heating, odors or abnormal noise from the motor or control box?

Turn the sewing machine OFF and contact your dealer if there is any heating, odors or abnormal noise.

[5]-1

Confirmation

Using the floppy disk

[6] Using the floppy disk

Floppy disk unit

(1) The floppy disk unit is used to [read/write] the 3.5-inch floppy disk on which the patterns are saved.

(2) A 3.5-inch 2HD type floppy disk can be used. Correctly orient the floppy disk, and carefully insert it in the direction of the arrow

LED Push-button while pressing the door shutter. If the insertion direction is mistaken and the disk is inserted with force, the floppy disk or the floppy disk unit could be damaged.

(3) When used for the first time, the floppy disk is not formatted. Refer to section [9]Basic mode operation - Program 2 mode for details on formatting the disk.

(4) Do not turn the power OFF or eject the floppy disk while the floppy disk unit is accessing

(reading, writing, formatting). (The LED on the floppy disk unit will flicker during these operations.) Failure to observe this could damage the floppy disk or saved data.

(5) The [LED] on the floppy disk unit will flicker while accessing the floppy disk unit (while reading, writing or formatting). The [LED 1] to [LED 5] displays on the setting panel will turn OFF during these operations, but this is not a fault.

* When the access is correctly completed, the [LED] on the floppy disk unit will turn OFF, and the [LED 1] to [LED 5] displays on the setting panel will change to the normal display.

* If accessing is completed with an error, the [LED] on the floppy disk unit will turn OFF, and an error message will display with [LED 1] to [LED 5] on the setting panel.

(6) Special maintenance and inspections are not required for the floppy disk unit mounted in the control box.

Applicable floppy disk

A: Sliding cover

This cover protects the magnetic surface.

A

B: Label

Write the data contents, etc., on this label.

C

B

D

C: Write-protect tab

This tab prevents important data from being inadvertently erased. Writing is prohibited when the square window is open, and is enabled when the window is closed. Set the write-protect tab to the prohibit side for a floppy disk on which important sewing data is saved.

D: Floppy disk type identification tab

A square window is opened on the 2HD type disk.

The 2DD type disk does not have a square window, and cannot be used.

Precautions for handling the floppy disk

The floppy disk is a delicate product.

Always observe the following points to protect important data.

(1) Never place magnets near the disk.

(2) Do not bend the disk.

(3) Avoid subjecting the disk to cigarette smoke.

(4) Do not place the disk where it will be subject to direct sunlight or near a heating appliance.

(5) Always make a copy of important data.

(6) Attach the label onto the floppy disk at the correct position.

(7) After using the floppy disk, store it in the case.

[6]-1

System installation method

[7] System installation method

Regarding floppy disc for installation

PLK-E series

F1

SYSTEM

:

Ver. ****

DATE

:

****/**/**

MITSUBISHIELECTRIC(1/4)

・System program for machine unit

・Model data table

・Step (comment) data

PLK-E series

F2

LANGUAGE

:

Ver. ****

DATE

:

****/**/**

MITSUBISHIELECTRIC(2/4)

・Liquid crystal panel system program

・Language data

PLK-E series

F3

PICTURE

:

Ver. ****

DATE

:

****/**/**

MITSUBISHIELECTRIC(3/4)

・Picture data

PLK-E series

F4

FONT DATA

:

Ver. ****

DATE

:

****/**/**

MITSUBISHIELECTRIC(4/4)

・Font data

Key used for turning the power

ON

Name Application

B

The system is not installed in the default state. Install the system with this full read function before using the sewing machine.

F1 >>> F2 >>> F3 >>> F4

Install only the main system program. read

F1

Install only the LCD panel system program. read

F2

System table read

Install the main system program, and read in the backed up setting table or step sequence data.(The system program is necessary for floppy disk which backs up. Please refer to chapter (P.[9]-9 and P.[14]-7 of operator control panel for the backup.)

(Floppy disk where backup was preserved.)

Install the LCD panel system program, LCD panel image data and LCD panel font data.

F2 >>> F3 >>> F4

Memo It is necessary to install again by a full lead when changing from the state not using the liquid crystal panel in the state used. （Please begin the installation operation after make sure to connecting the liquid crystal panel.）

[7]-1

System installation method

Installation method

For full read (normal) * Please begin installing when you use the liquid crystal panel with made to connect

.

1. Reading F1 floppy disk

(Reading system program)

*When the power is OFF, insert the F1 floppy disk. F1 floppy disk read request

*While holding down the F key, turn the power ON. (The message F 1. S Y S

H shown on the right will appear.) F A B C D

Press the D key.

*Model will be displayed.

0

Select a model using this key .

H

1 1 0.

B

F A B C D

(For a detailed description of models, refer to "Set up" attached to the head part.)

Press the D key.

*The step sequence file will be displayed.

Press the D key.

Communicating with the control box. The

7-segment display turns

OFF during communication. Wait until the F2 floppy disk is t d

Memo If the LCD panel is not to be connected, this procedure is completed with F1. Turn the power OFF once.

2. Reading F2 floppy disk

(Reading label (language data))

*At the completion of F1 floppy disk reading, the message shown on the right side will appear. Insert the F2 floppy disk.

Press the D key.

* Language data will appear.

Select a language using this key .

(For a detailed description of language data, refer to "Set up" attached to the head part.)

Press the D key.

Communicating with the liquid crystal panel. Wait until the display (value) stops, and the F3 floppy disk is requested.

[7]-2

H

H

P L K E.

P

F A B C D

F2 floppy disk read request

H

H

H

H

F A B C D

F 2. L B L

F A B C D

E N G L

F A B C D

L *. * * *

F A B C D

S

F

*. * * *

A B C D

System installation method

3. Reading F3 floppy disk

(Reading picture data)

*At the completion of F2 floppy disk reading, the message shown on the right side will appear. Insert the F3 floppy disk.

Press the D key.

Communicating with the liquid crystal panel. Wait until the display (value) stops, and the F4 floppy disk is requested.

4. Reading F4 floppy disk

(Reading font data)

F3 floppy disk read request

H

H

F 3. P I C

F A B C D

P *. * * *

F A B C D

F4 floppy disk read request

*At the completion of F3 floppy disk reading, the message shown on the right side will appear. Insert the F4 floppy disk.

Press the D key.

H

F 4. F N T

F A B C D

*It is displayed in the liquid crystal panel [Please turn off the reading completion power supply] when the display of the LED stops, it is installation completed and the

Communicating with liquid crystal panel. Wait until change in the display stops.

When change in the display is stopped, judge that installation is completed.

Please turn off the power supply here.

H

H

F *. * * *

F A B C D

M - 3 1 0

F A B C D buzzer rings.

Please turn off the power supply here once.

Memo : For the special specification sewing machine, there is a case where FD (the system file is written) is packed up together in accessory box. In that case after completing a standard installation of the above-mentioned. Please read the system file according to under mentioned points.

The system file is read

*FD ( adheres the label of the system file) is inserted in FDD.

*The power is turned while pressing the B key.

Press the D key.

*When D key is pushed again, writing the system file is begun.

*LED is turned off while installing.

*When a standard screen is displayed in the liquid crystal panel, the installation is completion.

Press the D key.

Communicating with liquid crystal panel. Wait until change in the display stops.

[7]-3

H

H

H

P L K E. G

F A B C D

P L K E.

P

F A B C D

F A B C D

System installation method

When incorrect floppy disk is inserted.

If you insert a wrong floppy disk and press the D key, error code M-200( ) or

M-213( ) will be displayed. In this case press the C key to cancel. And then after insert a correct floppy disk, press the D key again.

[7]-4

Operating the setting panel keys

[8]. Operating the setting panel keys

1.Display and function of each key in normal mode

When the power is turned ON (the switch turned ON), the LEDs 1,2,3,4 and 5 shown below will display. This state is called the [Normal Mode], and the following keys can be operated.

[ Display during normal mode setting ]

[UP allow]key (Jog [+])

Jogging in the forward direction can be executed.

Indicates whether the counter is valid or invalid .

Indicates the sewing machine speed setting value ([0] to [9]).

Indicates the pattern No.

(3-digits).

H

LED1 LED2 LED3 LED4 LED5

A B C D

F

[H]key

Executes the home return operation.

[F]key

The mode is changed over to the program mode.

[B]key

The mode is changed over to the bobbin winding mode.

[DOWN allow]key (Jog [-])

Jogging in the reverse direction can be executed.

[A]key

The mode is changed over to the speed setting mode.

[C]key

The message display

(M-**) is canceled.

[D]key

The mode is changed over to the pattern read mode.

2.Changeover to each mode

The [basic functions] and [application functions] from the [normal mode] can be set with this setting panel. The mode can be changes to the [various modes] and various [application functions] can set from the [normal mode] via the [program mode].

(*Refer to [12] Program mode list )

(1)Types of basic functions (normal mode)

Speed setting mode

(basic function)

Speed of speed dial

(speed)

Program mode

Transition to various modes

Bobbin winding mode

(basic function)

After the clamp is turned [ON] and the start switch is turned

On, the upper shaft will rotate.

Program read mode

(basic function)

Selection of read pattern No. .

Caution！ To return to the [normal mode] from the [program mode] and [basic functions],press the [[H] key].

[8]-1

Operating the setting panel keys

(2)Types of application functions (program mode)

Program mode P

* Writing of system software

* Setting of simple settings

Normal mode

Program mode

* Home correction

1

Program mode

* Writing and copying

2

Program mode

* Counter

3

Program mode 4

* Wiper, thread trimming, needle thread trimming detection

Program mode

* Simple setting 1

A

Program mode

* Simple setting 2

B

Program mode

* Changeover of input function logic.

Program mode

* Changeover of output function logic.

Program mode

* Confirmation of input/output state

C

D

E

Program mode

* Setting of clamp

Program mode

* Selection of input operation

Program mode

* Selection of output operation

G

K

L

Caution! 1.Changing from the [mode] to [another mode] is not possible.

2.To change the [various mode], always return to the [normal mode], and change the [various mode] via the [program mode].

3.To return to the [normal mode] from the [program mode] and [various mode], press the [[H] key].

[8]-2

Operating the setting panel keys

(3)To change from [normal mode] to [basic function] and [program mode]

*.To changeover to an [program mode] other than the [basic function (speed setting mode, bobbin winding mode, pattern read mode)], always press [F] key once.

Mode name

Speed setting mode

H

Key operation

1.Press the A key.

LED1 LED2 LED3 LED4 LED5

A B C D

F

[Control box setting panel]

Digital display

*.Changes to the speed setting mode.

Bobbin winding mode 1.Press the B key. *.Changes to the bobbin winding mode.

Pattern read mode 1.Press the D key.

Program mode 1 1.Press the F key.

2.Press the A key for 2 seconds or more.

Program mode 2 1.Press the F key.

2.Press the B key for 2 seconds or more.

Program mode 3 1.Press the F key.

2.Press the C key for 2 seconds or more.

Program mode 4 1.Press the F key.

2.Press the D key for 2 seconds or more.

Program mode P 1.Press the F key.

2.While holding down the key, press the key for 2 seconds or more.

Program mode A 1.Press the F key.

2.While holding down the key, press the A key for 2 seconds or more.

[8]-3

*.Changes to the pattern read mode.

*.Display flickers.

*.Changes to the program mode 1.

[(Home correction) mode]

*.Display flickers.

*.Changes to the program mode 2.

[(Write), (copy) mode]

*.Display flickers.

*.Changes to the program mode 3.

[(Counter) mode]

*.Display flickers.

*.Changes to the program mode 4.

[(Wiper), (thread trimming), (needle thread detection) mode]

*.Display flickers.

*.Changes to the program mode P.

[(System software write), (simple setting write) mode]

*.Display flickers.

*.Changes to the program mode A.

[(Simple setting) mode 1]

Operating the setting panel keys

Mode name

Program mode B

Key operation

1.Press the F key.

2.While holding down the key, press the B key for 2 seconds or more.

Program mode C 1.Press the F key.

2.While holding down the key, press the C key for 2 seconds or more.

Program mode D 1.Press the F key.

2.While holding down the key, press the D key for 2 seconds or more.

Program mode E 1.Press the F key.

2.While holding down the key, press the key and the

A key for 2 seconds or more.

Program mode G 1.Press the F key.

2.While holding down the key, press the key and the

C key for 2 seconds or more.

Program mode K 1.Press the F key.

2.While holding down the key, press the C key for 2 seconds or more.

Program mode L 1.Press the F key.

2.While holding down the key, press the D key for 2 seconds or more.

[8]-4

Digital display

*.Display flickers.

*.Changes to the program mode B.

[(Simple setting) mode 2]

*.Display flickers.

*.Changes to the program mode C.

[(Changeover of input function) mode 1]

*.Display flickers.

*.Changes to the program mode D.

[(Changeover of output function) mode 1]

*.Display flickers.

*.Changes to the program mode E.

[(Status of input, output function) mode 1]

*.Display flickers.

*.Changes to the program mode G.

[(Setting of clamp) mode 1]

*.Display flickers.

*.Changes to the program mode K.

[(Input operation selection) mode]

*.Display flickers.

*.Changes to the program mode L.

[(Output operation selection) mode]

Operating the setting panel keys

3.Display and function of each key in speed setting mode

When the [A] key is pressed once in the normal mode, the following [speed setting mode (basic function)] display will appear.

H

Changeover to normal mode function

The setting value displayed in LED 5 is validated, and the normal mode is returned to.

Setting value changeover function

(decrement)

With each press, the LED 5 display (setting value) will decrement by one.(0,9 ... 2,1,0,9)

Setting value changeover function

(increment)

With each press, the LED 5 display (setting value) will increment by one.(0,1 ... 8,9,0,1)

[Control box setting panel]

LED1 LED2

A

F

LED3

B

LED4

C

Key operation invalid

Nothing will occur even if the key is operated.

LED5

D

Setting value changeover function

(increment)

With each press, the LED 5 display (setting value) will increment by one.(0,1, ... 8,9,0,1)

4.Display and function of each key in the bobbin winding mode

When the [B] key is pressed once in the normal mode, the following [bobbin winding mode (basic function)] display will appear.

H

[Control box setting panel]

LED1 LED2 LED3 LED4

A B C

F

LED5

D

Changeover to normal mode function Key operation invalid

Nothing will occur even if the key is operated.

Caution ! If the start switch is turned [ON] while the pressure is lowered in the bobbing winding mode, the upper shaft will rotate, and the bobbin winding operation will take place.

If the clamp is raised, the bobbin winding operation will not take place.

Caution !

Always turn [OFF] the power before threading the needle.

If the needle must be thread while the power is [ON], thread it while paying attention to points

1 and 2 given below.

1.While the sewing machine is stopped during sewing (normal mode state), the presser foot can be [raised/lowered] by turning [ON/OFF] the [B] key (wind key).

2.Do not turn on the start switch while threading the needle. It is extremely dangerous.

To prevent turning On the start switch by mistake while threading, take measures such as moving the start switch away from the foot.

[8]-5

Operating the setting panel keys

5.Display and function of each key in the pattern read mode

When the [D] key is pressed once in the normal mode, the following [pattern read mode (basic function)] display will appear.

[Control box setting panel]

LED1 LED2 LED3 LED4 LED5

H

F

A B C D

Changeover to normal mode function

The normal mode will be returned to without executing the read of the pattern No. display in

Read destination selection function

The read destination is selected from the following two.

[LED1]=[F]...Read from floppy disk.

[LED1]=[I]...Read from internal memory.

While [F] key on and after [ ] key on pattern No. search function (decrement)

The display in LEDs 2,3 and 4 (pattern No.) will change to the previous display (pattern No.) with each press the [ ] key. The existing pattern No. will display in LEDs 2,3 and 4 while decrementing

(searching) in order.

Pattern read function

The pattern No. displayed in LEDs 2,3 and 4 will be read, and then the normal mode will be returned to.

Setting value changeover function (increment)

With each press, the LEDs 2,3 and 4 displays (setting values) will increment by one. (0,1 ... 8,9,0,1)

Pattern No. search function (decrement)

The display in LEDs 2,3 and 4 (pattern No.) will change to the next display (pattern No.) with each press. The existing pattern No. will display in LEDs 2,3 and 4 while incrementing (searching) in order.

Memo If there is no pattern data for the No., the LED will flicker, and if there is pattern data for the No., the

LED will turn ON. When the LED is ON, press the "D" key to start reading of the pattern.

6.HALT mode display and the function of each key

To stop the sewing machine during sewing (normal mode), press the HALT switch (attached to the sewing machine head).

The display switches to the [HALT mode] shown below. [HALT mode] display..[control box setting panel]

[HALT mode display] [Control box setting panel]

LED1 LED2 LED3 LED4 LED5

H

F

A B C D

1.During [HALT mode] display, the operation of the ([H] key), ([ ] key), ([ ] key), ([F] key), ([A] key),

([B] key), ([C] key), ([D] key) on the setting panel and the (start switch) operation are invalid.

2.When the HALT switch is canceled during the [HALT mode] display, the display switches to the

[normal mode] shown below.

[Normal mode display] [Control box setting panel]

H

LED1 LED2

F

A

LED3

B

LED4

C

LED5

D

1.The following operation is possible while the needle is stopped at the up position.

(1).Restart of sewing by pressing the start switch.

(2).Move to restart position using [ ] key and [ ] key.

(3).[UP/DOWN] of the work holder by turning {ON/OFF} the work holder switch.

(4).Change of sewing speed with the speed dial.

(5).[UP/DOWN] operation of the presser foot by turning [ON/OFF] the [B] key (wind key).

2.The following operation is possible while the needle is stopped at the down position.

(1).Restart of sewing by pressing the start switch.

(2).[UP/DOWN] of the work holder by turning [ON/OFF] the work holder switch.

(3).Change of sewing speed with the speed dial.

[8]-6

Basic mode operation

[9]. Basic mode operation

1.Program 1 mode (home position correct mode) display and the function of each key

*.After the [F] key is pressed under normal mode, if the [A] key is pressed for more than 2 seconds, the display switches to the [1 home position correction, (valid/invalid) setting] screen of the [program 1 mode (home position correct mode)] shown below.

*.When the [H] key is pressed, the device returns to the normal mode after saving the setting values.

Memo Set enlargement/reduction of the constant stitch length cannot be done from the setting panel.

[ ],

[F]key

[ ]key

Initial screen of [1.home position correction, (valid/invalid) setting]]

[ ],

[F]key

[ ]key

1. By pressing the [C],[D] keys, the [valid( )/invalid( ):LED4,5 display] state of home position correction can be switched.

2. Even if the home position correction setting is set to (invalid [ ]:LED 4,5 display), the device saves the (X axis correction amount [CX.]) and (Y axis correction amount [CY.]).

3. After the home position correction is written in, the home position correction setting is set to (invalid

[ ]:LED 4,5 display).

Initial screen of [2.home position X axis correction amount setting]

[ ],

[F]key

[ ]key

1. When the [C] key is pressed, the setting of X axis correction amount (LED 4,5 display) lowers by

0.1mm.

2. When the [D] key is pressed, the setting of X axis correction amount (LED 4,5 display) rises by

0.1mm.

3. The [front direction ( )/back direction ( ):LED2 display] setting of X axis correction amount is automatically switched by the setting of X axis correction amount (LED3,4,5 display).

4.The setting range of X axis correction amount setting (LED3,4,5 display) is within (-12.7mm) -

(+12.7mm).

Initial screen of [3.home position Y axis correction amount setting]

[ ],

[F]key [ ]key

1. When the [C] key is pressed, the setting of Y axis correction amount (LED 4,5 display) lowers by

0.1mm.

2. When the [D] key is pressed, the setting of Y axis correction amount (LED 4,5 display) rises by

0.1mm.

3. The [front direction ( )/back direction ( ):LED2 display] setting of Y axis correction amount is automatically switched by the setting of Y axis correction amount (LED3,4,5 display).

4.The setting range of Y axis correction amount setting (LED3,4,5 display) is within (-12.7mm) -

(+12.7mm).

[No. of Stitch Constant Enlargement/Reduction Setting] initial screen

[D2]

[ ],

[F]key

[U2]

[D1]

[ ]key

[U1]

Cannot be input here.

[9]-1

Basic mode operation

[D2]

[U2] [D1]

[ ],

[F]key

[U1]

[ ]key

[X Enlargement/Reduction Rate Setting] initial screen

[ ],

[F]key [ ]key

1. When the [A], [B], [C] or [D] key is pressed, the X enlargement/reduction rate (LED 2, 3, 4, 5 display) can be designated. The rate can be set in the range of 10.0% to 200.0% with a 0.1% unit.

To designate 200.0%, press the [A] key once at the 100.0% state.

2. If both the X, Y enlargement/reduction rate or just one rate has been changed, the calculation will be executed and the normal mode will be returned to when the [H] key is pressed. If the rates have not been changed, the normal mode will be returned to without executing the calculation.

[ Program Change from Setting Panel Prohibit Setting] initial screen

[ ],

[F]key [ ]key

1. When the [A], [B], [C] or [D] key is pressed, the Y enlargement/reduction rate (LED 2, 3, 4, 5 display) can be designated. The rate can be set in the range of 10.0% to 200.0% with a 0.1% unit.

To designate 200.0%, press the [A] key once at the 100.0% state.

2. If both the X, Y enlargement/reduction rate or just one rate has been changed, the calculation will be executed and the normal mode will be returned to when the [H] key is pressed. If the rates have not been changed, the normal mode will be returned to without executing the calculation.

Direction of movement to clamp

-Y direction

+X direction -X direction

+Y direction

[9]-2

Basic mode operation

2.Program 2 mode (pattern data write in, delete, copy mode) display and the function of each key

*.After the [F] key is pressed under normal mode, if the [B] key is pressed for more than 2 seconds, the display switches to the [1 write to internal memory] screen of the [program 2 mode (pattern data write in, delete, copy mode)] shown below.

*.When the [H] key is pressed, the device returns to normal mode without executing the function (write, delete, copy).

[ ]key [ ]key

Initial screen of [1.write to internal memory]

[ ]key

[ ]key

1. When the [F] key is pressed, the number that has already been input [flickers].

2. By pressing each of the [A],[B],[C] keys, the number (LED 2,3,4 display) to be written in can be specified.

3.When the [D] key is pressed, after writing in pattern data into the specified number (LED 2,3,4 display), the device enters the normal mode.

Note

Initial screen of [2.write to floppy disk]

Numbers without a pattern [light] and numbers with pattern [flickers]. Be aware that when the [D] key is turned on when [flickering], the pattern is automatically overwritten and the original pattern is deleted.

[ ]key

[ ]key

1. When the [F] key is pressed, the number that has already been input [flickers].

2. By pressing each of the [A],[B],[C] keys, the number (LED 2,3,4 display) to be written in can be specified.

3. When the [D] key is pressed, after writing in pattern data into the specified number (LED 2,3,4 display), the device enters the normal mode.

Note

Numbers without a pattern [light] and numbers with pattern [flickers]. Be aware that when the [D] key is turned on when [flickering], the pattern is automatically overwritten and the original pattern is deleted.

Initial screen of [3.delete one pattern from internal memory]

[U4]

[D4]

[ ]key

[ ]key

1. When the [F] key is pressed, the pattern number (LED2,3,4 display) of the pattern that has been written in is displayed in sequence and pattern number can be searched.

2. By pressing each of the [A],[B],[C] keys, the pattern number (LED 2,3,4 display) to be deleted can be specified.

3. When the [D] key is pressed, the pattern data of specified pattern number (LED2,3,4 display) is deleted. (The screen display does not change.)

[U3]

[D3]

[9]-3

Basic mode operation

[D4] [U3]

[U4] [D3]

[ ]key [ ]key

Initial screen of [4.delete one pattern from of floppy disk]

[ ]key

[ ]key

1. When the [F] key is pressed, the pattern number (LED2,3,4 display) of the pattern that has been written in is displayed in sequence and pattern number can be searched.

2. By pressing each of the [A],[B],[C] keys, the pattern number (LED 2,3,4 display) to be deleted can be specified.

3. When the [D] key is pressed, the pattern data of specified pattern number (LED2,3,4 display) is deleted. (The screen display does not change.)

Initial screen of [5.initialization of internal memory]

[ ]key

1. When the [D] key is pressed, the internal memory is initialized (all pattern data deleted) and the device enters the normal mode.

[ ]key

Initial screen of [6.initialization of floppy disk]

1. When the [D] key is pressed, the floppy disk is initialized to 1.44MB (all pattern data deleted) and the device enters the normal mode.

[ ]key [ ]key

Initial screen of [7.total copy to floppy disk]

[ ]key [ ]key

1. When the [D] key is pressed, all the pattern data in the internal memory is copied into a floppy disk and the device enters the normal mode. (For backup of pattern data.)

Note 1. If the floppy disk have already same pattern No., the new pattern data is over written it No. .

2. Current sewing pattern data don't copy this screen.

Initial screen of [8.total copy to internal memory]

[ ]key [ ]key

1. When the [D] key is pressed, all the pattern data in a floppy disk is copied into the internal memory and the device enters the normal mode. (For restore of pattern data.)

Note 1. If the internal memory have already same pattern No., the new pattern data is over written it No. .

2. Current sewing pattern data don't copy this screen.

[9]-4

Basic mode operation

3.Program 3 mode (counter mode) display and the function of each key

*.After the [F] key is pressed under the normal mode, if the [C] key is pressed for more than 2 seconds, the display switches to the [1 setting of down counter setting] screen of the [program 3 mode (counter mode)] shown below.

*.When the [H] key is pressed, the setting value becomes valid and the device returns to normal mode.

[ ], [ ]key

[F]key

Initial screen of [1.setting of down counter setting]

[ ],

[F]key

[ ]key

1.When each of the [A],[B],[C],[D] keys is pressed, the setting value of the down counter (LED 2,3,4,5 display) increments by [1].

2.The LED display is as follows: [LED2=1000 th

digit], [LED3=100 th

digit], [LED4=10 th

digit], [LED5=1st digit]

Initial screen of [2.down count value display]

[ ]key

1.While the down counter function is valid, during sewing, the [LED2,3,4,5] display is counted down

(decrement) in sequence.

2.The LED display is as follows:[LED2=1000th digit], [LED3=100th digit], [LED4=10th digit], [LED5=1st digit]

3.When the (down count setting [D.] reach the 0, the buzzer sounds.)

[ ],

[F]key

Initial screen of [3.setting of up counter setting]

[ ],

[F]key [ ]key

1.When each of the [A],[B],[C],[D] keys is pressed, the setting value of the up counter (LED 2,3,4,5 display) increments by [1].

2.The LED display is as follows: [LED2=1000 th

digit], [LED3=100 th

digit], [LED4=10 th

digit], [LED5=1st digit]

Initial screen of [4.up count value display]

[D6]

[ ],

[F]key

[U6]

[ ]key

[U5]

[D5]

1.While the up counter function is valid, during sewing, the [LED2,3,4,5] display is counted up

(increment) in sequence.

2.The LED display is as follows: [LED2=1000th digit], [LED3=100th digit], [LED4=10th digit],

[LED5=1st digit]

3.When the (upcounter setting [P.]) and (up count setting [U.] reach the same value, the buzzer sounds.)

[9]-5

Basic mode operation

[D6]

[U6]

[ ],

[F]key

[U5]

[D5]

[ ]key

Initial screen of [5.UP counter valid (ON)/invalid (OFF) setting]

1.When the [D] key is pressed, the (valid( )/invalid( ) : LED4,5 display) setting of the UP counter can be switched.

[ ],

[F]key

[ ]key

Initial screen of [6.DOWN counter valid (ON)/invalid (OFF) setting]

[ ],

[F]key [ ]key

1.When the [D] key is pressed, the (valid( )/invalid( ) : LED4,5 display) setting of the DOWN counter can be switched.

[9]-6

Basic mode operation

4.Program 4 mode ( wiper, thread trimming, needle thread trimming detection mode ) display and the function of each key

*.After the [F] key is pressed under the normal mode, if the [D] key is pressed for more than 2 seconds, the display switches to the [1 wiper setting] screen of the [program 4 mode (wiper, thread trimming, needle thread detection mode)] shown below.

*.When the [H] key is pressed, the setting becomes valid and the device returns to the normal mode.

[ ],

[F]key

[ ]key

Initial screen of [1.wiper setting]

[ ],

[F]key

1.By pressing the [C],[D] keys, the setting value of the wiper's [valid( switched.

[ ]key

Initial screen of [2.thread trimming setting]

) / invalid( ) : LED4,5] display can be

1.By pressing the [C],[D] keys, the setting value of the thread trimming's [valid( can be switched.

[ ],

[F]key

[ ]key

2.When the thread trimming is set to [invalid(

Initial screen of [3.needle thread trimming sensor setting 1]

) / invalid(

):LED4,5] display, the wiper's [valid(

) : LED4,5] display

)] setting value is ignored.

[ ],

[F]key

[ ]key

1.By pressing the [A] keys, the setting value of the needle thread trimming sensor's [valid( ) / invalid( ) : LED2] display can be switched.

2.By pressing the [B] key, the number of invalid stitches of the starting time stitch sensor [LED3] can be set.

3.By pressing the [C],[D] key, the number of invalid stitches of the stitch in progress sensor [LED4,5] can be set.

4.The number of stitches indicates the approximate stitches when stopping time.

Initial screen of [4.needle thread trimming sensor setting 2]

[ ],

[F]key

[U8]

[D8]

[D7]

[ ]key

[U7]

1.By pressing the [A],[B],[C],[D] keys, the speed at which the needle thread trimming detection is invalid can be set.

The display [ [ ][][ ][ ][ ] ] of the [4 needle thread trimming sensor setting 2] shown above is the setting at which the needle thread trimming detection is invalid when the sewing machine is rotating at a speed of

600 r/min or less.

[9]-7

Basic mode operation

[D8]

[U8]

[U7]

[D7]

[ ],

[F]key

[ ]key

Initial screen of [5.needle thread trimming sensor setting 3]

1.By pressing the [C] or [D] keys, setting the thread trimming (

[ ],

[F]key

[ ]key detection.

*.( ) with thread trimmer.

*.( ) without thread trimmer.

Initial screen of [6.Program Change from Setting Panel Prohibit Setting]

)/( ), when the needle thread trimming sensor

[ ],

[F]key [ ]key

1.By pressing the [C] or [D] keys, setting the prohibit setting ( valid/ )/( invalid/ )

[9]-8

Basic mode operation

5.Program P mode (system software, simple setting write mode) display and the function of each key

*.After the [F] key is pressed under the normal mode, if the [ ] and the [ ] are pressed for more than 2 seconds, the display switches to the [1 system software write setting] screen of the [program P mode (system software, simple setting write mode)] shown below.

*.Use this to [backup (save)] when special settings have been executed (factory settings changed) on the setting panel.

* Refer to section "[7]. System Installation method" for details on recovering the backup. Also please do [1.total data write] when aiming at the restoration of the [B] lead.

[ ]key

[ ],

[F]key

Initial screen of [1.total data write]

[ ],

[F]key [ ]key

1.Pressing the [D] key begins [1 system software writing], [2 language data writing] and [3 simple setting table writing].

When the writing is completed, the device returns to the normal mode.

2.When the [H] key is pressed, the setting is not executed and the device returns to the normal mode.

Initial screen of [2.simple setting table write]

1.Pressing the [D] key begins the writing of the data of the internal memory into the floppy disk.

[ ],

[F]key [ ]key When the writing is completed, the device returns to the normal mode.

2.When the [H] key is pressed, the setting is not executed and the device returns to the normal mode.

Initial screen of [3.step sequence data write]

1.Pressing the [D] key begins the writing of the data of the internal memory into the floppy disk.

[ ],

[F]key [ ]key

When the writing is completed, the device returns to the normal mode.

2.When the [H] key is pressed, the setting is not executed and the device returns to the normal mode.

Initial screen of [4.simple setting table read]

[ ],

[F]key

[U10]

[D10]

[U9]

[D9]

[ ]key

[D]key

1.By pressing the [D] keys, it changes into the simple setting table selection screen

2.When the [H] key is pressed, the setting is not executed and the device returns to the normal mode.

Initial screen of [4-1.simple setting table select]

1. The file is selected with [A],[B] keys. And pressing the [D] key begins the reading of the data from the floppy disk to the internal memory.

2. The buzzer rings when reading ends, and turn off the power supply once, please.

[9]-9

Basic mode operation

[D10]

[D9]

[ ],

[F]key

[U10]

[U9]

[ ]key

Initial screen of [5.step sequence data read]

[ ],

[F]key

[ ]key

[D]key

1.By pressing the [D] keys, it changes into the step file selection screen

2.When the [H] key is pressed, the setting is not executed and the device returns to the normal mode.

Initial screen of [5-1.step file select]

1. The file is selected with [A],[B] keys. And pressing the [D] key begins the reading of the data from the floppy disk to the internal memory.

2. The buzzer rings when reading ends, and turn off the power supply once, please.

Initial screen of [6. simple setting table and step sequence data read]

[ ],

[F]key

[ ]key

[D]key

1.By pressing the [D] keys, it changes into the simple setting table selection screen

2.When the [H] key is pressed, the setting is not executed and the device returns to the normal mode.

Initial screen of [6-1.simple setting table select]

1. The file is selected with [A],[B] keys. And pressing the [D] key begins the reading of the data from the floppy disk to the internal memory.

2. It changes into the step file selection screen, when reading ends

Initial screen of [6-2.step file select]

1. The file is selected with [A],[B] keys. And pressing the [D] key begins the reading of the data from the floppy disk to the internal memory.

Initial screen of [4.selection of setting table number]

2. The buzzer rings when reading ends, and turn off the power supply once, please.

[ ],

[F]key

1.By press the [D] key, the setting table No.[1] - [7].

2.When the [H] key is pressed, the setting is not executed and the device returns to the normal mode.

[ ]key

Note : Setting table don't have following things

1.Program [1] - [4] and [P] mode.

2.Program B mode [R8].

3.Setting value for teaching panel.

[9]-10

This page is a blank.

Basic mode operation

[9]-11

[10] Customized input/output

(1). Customized input/output configuration diagram

A B

(Input port)

* Terminal block

* Connector

Input control section

Details A

Physical input RAM

I1

I2

I3

I4

I5

IP

Virtual input

RAM

S1

F

Two stage clamp input

Sewing machine operation prohibit

Home position return prohibit

Virtual input 0

Virtual input 1

Virtual input F

C

Virtual output

RAM

T

L

W

OF1

PF

Two stage clamp output

Virtual output 0

Virtual output 1

Virtual output F

D

Physical output RAM

O1

O2

O3

O4

O5

OO

Details B

E

Output control section

(Output port)

* Terminal block

* Connector

・

WL

Input/output setting mode

(2). Outline of customized input/output mode

(A to E below correspond to A to E in the [20] 1. Customized input/output configuration diagram.)

(1) Customizing the input signal

A. The ON/OFF signal input from the input port passes through the input control section (no operation, alternate operation, signal reversal), and is then stored in the physical input RAM area corresponding to the input port.

B. Each signal stored in the physical input RAM area is connected to a desired position in the sewing machine control virtual input RAM port.

C. The sewing machine carries out control based on the function assigned to the virtual input area.

(2) Customizing the output signal

D. As opposed to the customized input, the virtual output RAM area port, assigned a specific meaning, can be connected and set to a desired position in the physical output RAM area port.

E. The signal for each port in the physical output RAM area passes through the output control section

(no operation, delay circuit, alternate, etc.), and is then output to the output port.

(3). Customizing the virtual input/output RAM

Input control section

Physical input RAM

Customized input

Standard

I1

I2

I3

I4

Virtual input RAM

S1

F

IP

Virtual output RAM

Customized output

Physical output RAM

T

L

FU

O1

O2

O3

O4

OQ

Output control section

Standard

Selection and connection of physical input/output RAM port and virtual input/output RAM port

For example, to connect the physical input RAM port [I1] and virtual input RAM port [SRT] (start) and to connect the physical output RAM port [O1] and virtual output RAM port [T] as shown in the diagram, set as follows.

1. Using customized input, select the [I1] input functions, and set SRT.

2. Using customized output, select the [O1] input functions, and set SRT.

With the above settings, [I1] and [SRT], and [O1] and [T] will be connected.

One port from the virtual input RAM ports can be selected for the [I*] port by changing the setting.

One port from the virtual output RAM ports can be selected for the [O*] port by changing the setting.

[10]-2

Input/output setting mode

(4). Block diagram (input control section)

Standard

A OF

ON

Logic changeover

B Alternate

NO

AL

C

Operation changeover

Physical input

RAM

(5). Explanation of operations (input control section)

The input signal passes through the A point, B point and C point of the input port, and finally is connected to the physical input RAM.

A point: Inputs the signal to the input port from an external source.

B point: (1) When the logic setting is set to "normal"(OF), the operation will be the same as the input signal A point.

(2) When the logic setting is set to "reverse"(ON), the operation will be the reverse of the input signal A point.

C point: (1) When the operation selection is set to "normal"(NO), the operation will be the same as the input signal B point.

(2) When the operation selection is set to "alternate"(AL), the signal will turn ON at the first rising edge, turn OFF at the second rising edge, and will turn ON at the third rising edge. The signal waveform will repeatedly turn ON and OFF at the input rising edge.

The C point signal input and controlled in the above manner is input into the physical input RAM port.

Input port A

Logic changeover

Logic operation selection when logic changeover is set to

"normal"

Logic operation selection when logic changeover is set to

"reverse"

"Normal"

"Reverse"

"Normal"

"Alternate"

"Normal"

"Alternate"

B

B

C

C

C

C

[10]-3

(6). Block diagram (output control section)

Physical output

RAM

O1

O2

O3

Operation selection

NO

AL

A

C

Logic changeover

OF

ON

D

ON delay

OF

ON

ON delay

Setting time

Chopping

OF

ON

Full wave time

B

NO

D

ON delay

Setting time

Duty

Full wave time

Setting value x 10ms

E

Output port

ALL=100% ON

66L =66% ON(8ms ON/4ms OFF）

66H =66% ON(4ms ON/2ms OFF）

50L =50% ON(4ms ON/4ms OFF）

50H =50% ON(2ms ON/2ms OFF）

33 =33% ON(2ms ON/4ms OFF）

17 =17% ON(2ms ON/10ms OFF）

8 = 8% ON(2ms ON/22ms OFF）

Input/output setting mode

(7). Explanation of operation (output control section)

The operation of the signal output from the physical output RAM is selected and then the signal is connected to the output port F point.

A point: Logic operation selection

(1) When "normal"(NO) is selected, the input waveform is connected.

(2) When "alternate"(AL) is selected, the signal will alternately turn ON and OFF, turning ON at the first rising edge and OFF at the next rising edge.

Input signal

01

Normal

Alternate

A

A

B point: ON delay setting

(1) When "invalid" is selected, the same signal as the A point will be output to the D point.

(2) When "valid" is selected, the waveform will rise after the {set value x 10(ms)} time (*1) set with the A point input waveform. (ON delay)

Input signal

Invalid

Valid

A

B

B

*1

Delay time to ON

Setting value(*1) x 10(ms)

C point: OFF delay setting

(1) When "invalid" is selected, the same signal as the C point will be output to the D point.

(2) When "valid" is selected, the ON time will be delayed by the {set value x 10(ms)} time (*2) set with the C point input waveform.

Input signal

B

Invalid

Valid

C

C

*2

Delay time to OFF

Setting value(*2) x 10(ms)

D point: Logic setting

(1) When "normal" is selected, the C point signal will be output to the D point without any changes.

(2) When "reverse" is selected, the C point signal will be output to the D point.

Input signal

Normal

C

D

Reverse D Signal reversal

[10]-5

Input/output setting mode

E point: Chopping setting

(1) When "invalid" is selected, the D point signal will be output to the E point without any changes.

(2) When "valid" is selected, the signal will turn ON for the time (set value x 10) set with [*T] at the

F point signal rising edge.

After that, the square-wave of the duty rate set with [*C] will be output.

Input signal

D

Invalid E

Valid E

Full wave time

Duty

Setting value x 10(ms)

Duty ALL=ALL=100% ON

66L=66% ON (8ms ON/4ms OFF)

66H=66% ON (4ms ON/2ms OFF)

50L=50% ON (4ms ON/4ms OFF)

50H=50% ON (2ms ON/2ms OFF)

33 =33% ON (2ms ON/4ms OFF)

17 =17% ON (2ms ON/10ms OFF)

8 = 8% ON (2ms ON/22ms OFF)

[10]-6

Input/output setting mode

[11] Input/output setting mode

(1) Input signal setting table

Serial

No.

Function Specifications

Each time the input signal (FSP) is turned ON, the presser output [1], [2], [3], [4], [5],

[6], [7] and [8] will turn <<ON>> in sequence.

mode], this input signal (FSP) will be invalid.

Each time the input signal (FSM) is turned ON, the presser output [8], [7], [6], [5], [4],

[3], [2] and [1] will turn <<ON>> in sequence. mode], this input signal (FSM) will be invalid.

Each time the input signal (FP1) is turned ON, the presser output [1], [2], [3] and [4] will turn <<ON>> in sequence.

If either of the following is established, this input signal (FP1) will be invalid:

[When "number of presser division setting (OFB)" in the program/pressure mode is set to NO or 4]

[When the "valid presser number for divided presser setting (F21N)" is set to 1]

Each time the input signal (FM1) is turned ON, the presser output [4], [3], [2] and [1] will turn <<ON>> in sequence.

If either of the following is established, this input signal (FM1) will be invalid: set to NO or 4]

[When the "valid presser number for divided presser setting (F21N)" is set to 1]

Each time the input signal (FP2) is turned ON, the presser output [5], [6], [7] and [8] will turn <<ON>> in sequence.

If either of the following is established, this input signal (FP2) will be invalid: set to NO or 4]

[When the "valid presser number for divided presser setting (F22N)" is set to 1]

Each time the input signal (FM2) is turned ON, the presser output [8], [7], [6] and [5] will turn <<ON>> in sequence.

If either of the following is established, this input signal (FM2) will be invalid: set to NO or 4]

[When the "valid presser number for divided presser setting (F22N)" is set to 1]

Each time the input signal (A2F) is turned ON, the following operations (1), (2) and

(3) will be repeated in sequence.

Note that this is valid only when the [pneumatic type two stage clamp setting (AF2.)] function in the program mode is set to [ON].

(1) When the input signal (A2F) is turned ON [first time], the pneumatic type two stage clamp low pressure output (AFL) will turn <<ON>>, and the pneumatic type two stage clamp residual pressure removal output (AFE) will turn <<OFF>>. stage clamp low pressure output (AFL) will turn <<OFF>>, pneumatic type two stage clamp high pressure output (AFH) will turn <<ON>>.

(3) When the input signal (A2F) is turned ON [third time], the pneumatic type two stage clamp high pressure output (AFH) will turn <<OFF>>, and the and the pneumatic type two stage clamp residual pressure removal output (AFE) will turn

<<ON>>.

When the input signal (IF1) turns ON, the presser output 1 (OF1) will turn ON. When

9…16 IF1…IF8

(Same for IF2 to IF8).

When the input signal (F1C) is ON, output (ON) of the presser output 1 (OF1) will be prohibited.

17…24 F1C…F8C [Operation of the presser output 1 input signal (IF1) is invalidated.]

(Same for F2C to F8C).

When the input signal (OFC) is ON, output of the presser output 1 (OF1) to presser output 8 (OF8) are all prohibited.

(IF8) is invalidated.]

[11]-1

Input/output setting mode

Serial

No.

Function Specifications

When the input signal (TC) is ON, the thread trimming operation output [thread

27 TC prohibited.

If the input signal (S6) turns ON while the sewing machine is running, the sewing machine will stop. Operation will resume when the signal is turned OFF. trimmed, operation will not resume until this input signal (S6) is turned OFF.

When the input signal (HPC) is ON, home position return operations will be

Use prohibited

30 --1

When [program/thread breakage sensor mode "needle thread breakage sensor valid/invalid setting (S1) is ON]:

If the input signal (THS) is input (ON) during sewing, the sewing machine will halt according to the value set for the number of invalid stitches for the halt

31 THS sensor, and a message code [M-21] will appear. (State can be recovered.)

When [program/thread breakage sensor mode "needle thread breakage sensor valid/invalid setting (S1) is OFF]:

Even if the input signal (THS) is input (ON) during sewing, the sewing machine will not stop.

If the input signal (ARS) is turned ON during stitching (while the power is ON), the

32 ARS recovered. Turn the power OFF.)

When the input signal (IO0) turns ON, the virtual output signal 0 (OT0) will turn ON

33…48 IO0…IOF at any time. (Same for IO1 to IOF)

Nothing will happen even if the input signal NO is turned ON.

49 NO

When the input signal (SRT) is turned ON, the sewing machine will start stitching.

When the input signal (HP) is turned ON, the home position return operation will be

51 HP running.

When the input signal (WID) is turned ON, the mode will change from the [normal

When the input signal (JGP) is turned ON, the presser will move (jog) in the forward

53 JGP

[Same operation as jog key (forward direction) on the panel.]

When the input signal (JGM) is turned ON, the presser will move (jog) in the reverse

54 JGM

[Same operation as jog key (reverse direction) on the panel.]

When the input signal(STP) is turned ON, the sewing machine will halt.

The needle will stop just before the fabric to confirm the position for puncturing the fabric with the needle. Each time the input signal (BC) is turned ON, the operation will be repeated in the order of 1. [Forward run] , 2. [Reverse run] , 3. [Forward run].

If the start switch is then turned ON and the next stitching data indicates stitching, feed, M-20 will appear. Raise the needle to the UP position once, and then turn the start switch ON.

[This can be adjusted with the [needle DOWN angle setting] in the function mode.]

When the input signal (CCL) is turned ON, the counter will be cleared. [Same operation as [Counter Clear] key.] mode.

When the input signal (SRC) is turned ON, start stitching with the start input signal

When the input signal (CCU) is turned ON, the up counter will be cleared.

59 CCU

When the input signal (CCD) is turned ON, the down counter will be cleared.

60 CCD

When the input signal (UAD) is turned ON, the up counter will increment by one.

61 UAD

When the input signal (UDC) is turned ON, the up counter will decrement by one.

62 UDC

When the input signal (DAD) is turned ON, the down counter will increment by one.

63 DAD

When the input signal (DDC) is turned ON, the down counter will decrement by one.

64 DDC

[11]-2

Input/output setting mode

(2) Output signal setting table

Serial

No.

Function Specifications

When the input signal (IO0) that outputs to the virtual output 0 is turned ON, the virtual output signal (OT0) will turn ON at any time.

(Same for OT1 to OTF)

17...24 FN1...FN8

When the pattern data function code 1 data (FNC1) is read in during sewing, the function code 1 output signal (FN1) will be reversed <<ON/OFF>>

* When function code 1 data (FNC1) is read in at an odd number:

[The function code 1 output signal (FN1) will turn <<ON>>.]

* When function code 1 data (FNC1) is read in at an even number:

[The function code 1 output signal (FN1) will turn <<OFF>>.]

(Same for FN2 to FN8)

25...32 OF1...OF8

When the presser input signal 1 (IF1) is turned ON, the presser output signal 1

(OF1) will turn ON. When the presser input signal 1 (IF1) is turned ON, the presser output signal 1 (OF1) will turn OFF.

(Same for OF2 to OF8)

Nothing is output.

33 NO

The thread trimming output signal will turn [ON/OFF].

34 T

The thread release output signal will turn [ON/OFF].

35 L

The wiper output signal will turn [ON/OFF].

36 W

The presser foot output signal will turn [ON/OFF].

37 PF

When the pneumatic type two stage clamp input signal (A2F) is turned ON [first time], the pneumatic type two stage clamp low pressure output (AFL) will turn ON.

Note that this is valid when the [pneumatic type two stage clamp setting (AF2)] in the

[G] mode is set to [ON].

When the pneumatic type two stage clamp input signal (A2F) is turned ON [second time], the pneumatic type two stage clamp high pressure output (AFH) will turn ON.

Note that this is valid when the [pneumatic type two stage clamp setting (AF2)] in the

[G] mode is set to [ON].

When the pneumatic type two stage clamp input signal (A2F) is turned ON [second time], the pneumatic type two stage clamp excess presser release output (AFE) will turn ON. Note that this is valid when the [pneumatic type two stage clamp setting

(AF2)] in the [G] mode is set to [ON].

The home position output signal (DHP) will turn ON when the sewing machine is stopped at the home position.

[Note that this will turn on at the virtual home position instead of the mechanical home position when free home position or home position correction is executed.]

The secondary home position output signal (D2H) will turn ON when the sewing machine is stopped at the secondary home position.

If the sewing machine can be driven (the presser is lowered (ON)), when the start switch is pressed, the READY output signal (RED) will turn ON.

When the sewing machine is stitching (including non-stitching feed), the during stitching signal (DSW) will turn ON.

When the sewing machine starts to rotate after feed without stitching, the output signal (SP) will turn ON.

The thread trimming start output signal (TSE) will turn ON when the thread trimming operation starts.

The stitching end output signal (END) will turn ON when one stitching pattern is completed.

When the sewing machine is halted with the HALT code data (UST, DST) during stitching, the HALT (code) output signal (DCS) will turn ON.

The halted output signal (DST) will turn ON while the sewing machine is halted.

49 DST

The during home return output signal (HPO) will turn ON while the sewing machine is returning to the home position.

The error occurrence detection output signal (ERR) will turn ON when and error or message occurs.

When the up counter count value matches the set value, the count up completed output signal (CUE) will turn ON.

[11]-3

Input/output setting mode

Serial

No.

Function Specifications

When the down counter count value reaches [0], the count down complete output signal (CDE) will turn ON.

When the sewing machine is stopped due to thread breakage detection, the stopped due to needle thread breakage detection output signal (DTS) will turn ON.

Use prohibited.

55 --1

The sewing machine rotating output signal (DRT) will turn ON while the sewing machine is rotating.

The DOWN position output signal (DN) will turn ON when the DOWN position signal is input from the detector.

This is the buzzer output signal for notifying that a sewing machine error or message has occurred.

The UP position output signal (UP) will turn ON when the UP position signal is input from the detector.

This is the power ON output signal.

60 PWR

[11]-4

Program mode list

[12] Program mode list

Changing to the program mode

When using the LCD panel, refer to the section " Operation panel section[16] Program mode ". When using the 7-segment operation panel keys, refer to pages " Control unit section[8]-3 to [8] -4".

* For item (*1), there is no LCD panel program mode item. Change to each mode using the 7-segment operation panel keys.

Depending on the item, the other LCD panel functions can be operated. (For example, [O1L] in the "output signal" item can be operated from the "input/output setting mode".)

Table explanation

[ type ]

[ symbol ] [ function name ] [mode]

Wiper

W1

W2

Wiper output (W) output start time

Wiper output (W) output time

Sewing area

ALC

XL

XR

YU

YD

Sewing area limit cancel

[X axis left side] area limit setting

[X axis right side] area limit setting

[Y axis back side] area limit modification

[Y axis front side] area limit modification

Needle position

RU

Reverse run needle UP function after thread trimming

R8

U8

D8

RU reverse angle setting

Needle UP position stop angle

Needle DOWN position stop angle

4(1)

B34

B35

Home position

HPM

HPC

HPF

Home position return method at HALT

Home position return prohibit at power

ON

Automatic home position return operation prohibition

A10

A11

Slow start

S

SL

SLN

Clamp

OST

Start/stop even if work holder is not lowered

G40

G1

RP(1-8) Work holder 1-8 repeat sewing setting G(2-9)

WHY Work holder order of priority setting G10

FSR All cancel during step over operation G11

1PD

1T

(1-8)A

(1-8)B

OFB

FN

CF

F21N

F22N

CF1

CF2

F4BN

F4SN

AF2

1-pedal specification setting

1-pedal timer setting

Work holder 1-8 ON delay timer setting

Work holder 1-8 OFF delay timer setting

G12

G13

G(14-

21)

G(22-

29)

Number of Work holder division setting G30

G31

G32

Number of rated Work holder setting

Work holder sequence setting

Valid Work holder number setting for divided Work holder (OF1…OF4)

Valid Work holder number setting for divided Work holder (OF5…OF8)

Work holder sequence setting for divided Work holder (OF1…OF4)

Work holder sequence setting for divided Work holder (OF5…OF8)

Valid number setting of Work holder blocks

Number of block steps setting

Pneumatic type two stage work holder selection

G33

G34

G35

G36

G37

G38

G39

Bobbin winding

WSM

WT

Slow start speed

Slow start setting

Number of slow start stitches

Bobbin winding operation setting

Bobbin winding operation time

B44

B45

B46

A1

X5

X6

X7

A12

HPK

2HS

FHP

CHS

Reset key setting

Temporary stop method at secondary home position

Free home position usage method

Home position correct selection at sewing data read

A14

A15

A16

A17

SHX [ X axis ] limit sensor home position return X9

SHY [ Y axis ] limit sensor home position return X10

Setting for presser foot state of home

HPS A13 return operation after power ON

HALT

STF

STN

STS

ST2

STP

STD

STL

Counter

CUP

CDN

UCM

DCM

PCM

CN

UCC

DCC

USC

DSC

Feed data stop state at HALT switch operation

Needle stop state at HALT switch operation

Various output hold at HALT switch operation

HALT switch two-press operation

Power operation at HALT switch operation

Work holder raise operation when stopped with HALT code

Double-drop prevention after HALT

Increment (UP) counter function

Decrement (DN) counter function

Increment (UP) counter setting value clear method

Decrement (DN) counter setting value clear method

Counter clear method at power ON

Number of stitches count function

Increment (UP) counter count value correction prohibit

Decrement (DN) counter count value correction prohibit

Sewing work with increment (UP) counter

Sewing work with decrement (DN) counter

A2

A3

A4

A5

A7

A8

A9

A21

A22

A23

A24

A25

A26

A27

A28

A29

A30

X8

Brakes

B5

B6

B7

B8

BKM

BNR

BKT

PW

Weak brake function setting

Weak brake noise setting

Brake time setting

Weak brake operation time during presser bar lifting operation

B1

B2

B3

B4

X23

B47

B48

B49

Presser foot

PD

PU

UW

BPF

[12]-1

Presser bar lifting timer 1 (lowering) setting

B36

Presser bar lifting timer 2 (rising) setting B37

Presser bar lifting timer 3 (rising) setting B38

Setting of presser foot when baste is sewn and the feed moves

B26

Program mode list

Tread trimming sensor

S1

S2

S3

B

TST

Needle thread breakage sensor valid/invalid

Number of stitches to invalidate thread breakage sensor at stitching start

Number of stitches to invalidate needle thread breakage sensor during stitching

Needle thread breakage sensor operation speed setting

Thread trimming valid/invalid at needle thread breakage sensor detection

Feed method

WET

WEL

WEM

WEH

Work holder weight selection

Setting value for Work holder weight

(WET) = [L] selection

Setting value for Work holder weight

(WET) = [M] selection

Setting value for Work holder weight

(WET) = [H] selection

4(3)

4(3)

4(3)

4(4)

4(5)

B10

B11

B12

B13

B14

TL

TM

TH

Setting value for fabric thickness (THI)

= [L] selection

Setting value for fabric thickness (THI)

= [M] selection

Setting value for fabric thickness (THI)

= [H] selection

B15

B16

B17

FEM

FES

FSM

TYA

Feed data mode selection

Feed data speed simple setting

Smooth feed data setting

Teaching arrow MAX movement amount (multiplication) setting

Sewing speed

B18

B23

B24

B25

Thread trimming timing

LTM

LLM

T1

T2

L1

L2

Thread trimming output (T) output mode

B27

Thread release output (L) output mode B28

Thread trimming output (T) output start time/angle

Thread trimming output (T) output time/end angle

Thread release output (L) output start time/angle

Thread release output (L) output time/end angle

B29

B30

B31

B32

T B43

ETC

TRM

LP

Thread trimming speed

Thread trimming cancel at needle lifting with needle UP key setting

Thread trimming ON/OFF

Setting for tension release outputs time length at presser foot rise

A6

4(2)

B33

Step

B39

B40

B41

B42

STE

Step pointer clear at setting table changeover setting

X37

N2

N1

SUU

Number of execution lines per main loop

N3

Feed angle

S8

E8

T8

8D

Feed start angle setting

Feed end angle setting

Feed end angle setting at low speed

Angle display from needle DOWN position

Jog

JGM

UJC

Jog key function setting

Jog key valid setting at position other than needle UP position stop

B19

B20

B21

B22

A19

A20

[12]-2

LCD panel

KBC

LOF

LNN

KNO

LCD panel buzzer cancel

LCD panel backlight OFF function

LCD panel display color

Standard mode background selection

D1

D2

D3

L1

L2

L3

A31

X29

X30

X31

X32

X33

X34

X35

X36 R LCD panel backlight OFF time

Input signal

I1

I1L

I1M

(*1)[I1] Input function selection

(*1)[I1] Input logic changeover

(*1)[I1] Input operation selection

Output signal

O1

O1L

O1C

O1M

O1D

O1E

1A

1B

1T

1C

(*1)[O1] Output function selection

(*1)[O1] Output logic changeover

(*1)[O1] Output chopping function

(*1)[O1] Output operation selection 1

(*1)[O1] Output ON delay setting

(*1)[O1] Output OFF delay setting

(*1)[O1] Setting of delay time to output

ON/pulse output OFF time

(*1)[O1] Setting of ON time/pulse output ON time

(*1)[O1] Setting of output full wave output time

(*1)[O1] Setting of output chopping duty

C1

C2

K1

L4

L5

L6

L7

Miscellaneous

GA

MIL

APC

POF

ASC

AER

PFL

LH

LCK

PTC

Gain high/low changeover function

Milling mode ON/OFF

Sewing data designation with terminal block input function

Offset value selection for sewing data designation with terminal block input

The sewing speed is specified by the external input.

Error code output with output function

Internal memory overwrite prohibit

Maximum stitch length for continuous sewing

Program Change from Setting Panel

Prohibit Setting

Change in setting table number from the sewing data

B9

N4

X24

X25

X26

X27

A32

X38

4(6)

A18

SCP Permutation of short cut button B50

DFR

Method of reading the needlework data from floppy disk (Overwrite / Append)

B51

DV (*1) Setting table version No.

T (*1) display

BV

SV

(*1) System ROM version No. display

(*1) System software version No. display

E1

E2

E3

E4

E5

E30

E31

E32

E33

E34

E35

E36

E37 O1O (*1)Output

O1D (*1)Output

P (*1) Cumulative power ON time display

E61

E85

M (*1) Motor power ON time display E86

E87

E88

E89

E90

Special << Do not use >>

13. Error Display

1.Power [OFF] Display

*.An [error code No.] lights on the display of the setting panel and the explanation is displayed in the liquid crystal panel.

*. When an [error code No.] is displayed, confirm the [error code No.] and investigate the cause according to the following table.

Error Code

Display

Function name Probable cause

PWR.OF Power [off] display *.Displayed when the power is turned [off].

While this display is on, power can be turned [on] again.

*.Power source wiring OK?

[Message] It is a termination.

Inspection

*.The display will automatically turn off after a certain time.

*.Check the halt switch wiring.

STOP Halt switch [on] *.Turn [on] the halt switch.

*.Is the halt switch wiring broken(connection failure)?

[Message] HALT SW IS PRESSED

*.Turn [off] the halt switch.

*.Check the halt switch wiring.

2.[E-**] error code (Restoration impossible)

*. When the control panel detects an error, an [error code No.]lights on the display of the setting panel, and the [buzzer] sounds continuously.

*. When an [error code No.] is displayed, confirm the [error code No.] and investigate according to the following table.

*. The machine can be restored to the [normal mode] by turning [OFF] the power once and turning it On again.

Error Code

Display

Function name Probable cause Inspection

E-001 Main Motor over current trip

Power [off]

*.Is the wire to the motor short-circuited?

*.Is the sewing machine load torque too high?

[Message] MOTOR OVERCURRENT DETECTION WORKED.

*.Check the motor wiring.

*.Check the sewing machine.

E-002 Over Voltage Power

Power [off]

*.Is the power voltage too high?

*.Is the sewing machine inertia too high?

[Message] OVERCURRENT DETECTION WORKED.

*.Check the power voltage.

E-003 Encoder error

Power [off]

*.Is the connector to the motor encoder securely inserted?

*.Are the signals from the motor encoder correct?

*.Belt ok?

*.Is the sewing machine locked?

*.Is the motor locked?

[Message] ENCODER DEFECT POWER OFF

*.Check the connector insertion.

*.Check the encoder signals.

*.Check the belt.

*.Check the sewing machine.

*.Check the motor.

E-004 Motor connector error

Power [off]

*.Is the connector of the motor completely inserted?

*.Is not the signal of the connector of the motor disconnected?

[Message] MOTOR CONNECTER ERROR

*.Check the connector insertion.

*.Check the connector.

E-011

E-020

E-025

E-008

E-009

E-010 confirmation) of panel)

E-026

The detector is abnormal.

Power [off]

The solenoid is abnormal.

Power [off]

The home position sensor is abnormal. Power [off]

The memory is abnormal.

Power [off]

The liquid crystal panel is abnormal. Power [off]

Air pressure low Power [off]

[PMD]over current trip

Power [off]

*.Is the connector of the position detector firmly inserted?

*.Is not the signal of the position detector disconnected?

[Message] THE DETECTOR BREAKS OR THE SIGNAL CUTS.

*.Is not the signal of the position detector disconnected?

*.The solenoid is defective. (rolling wire defect)

[Message] THE SOLENOID BREAKS.

*.Does the wiring for the home position sensor Is disconnected or it not short-circuited?

*.Is not the model mistaken?

[Message] STATE OF HOME SENSOR DOES NOT CHANGE.

*.Information could not saved correctly at the last power off

[Message] INFORMATION COULD NOT SAVED CORRECTLY AT

THE LAST POWER OFF

*. Does the wiring for the liquid crystal panel Is disconnected or

it not short-circuited?

[Message] LCD PANEL CONNECTION ERROR

*.Air pressure low detection input signal (ARS) has been input.

[Message] LESS PRESSURE

*.Is the stepping motor wiring broken(connection failure, short circuit)?

[Message] PMD OVER

*.The connector is examined.

*.The signal is examined.

*.The connector is examined.

*.The signal is examined.

*.The wiring for the home position sensor is examined.

*.The model is examined.

*.Examines with (Home position/encoder /detector

input/output setting mode. (When connect the liquid crystal

*.Please install system software again.

*.The wiring for the liquid crystal panel is examined.

*.Turn [off] the power and remove failure portion.

*.Check the stepping motor wiring.

M-012

M-013

M-014

M-015

M-016

M-017

M-018

M-007

M-008

M-009

M-010

M-011

3.[M-**] message code (Restoration possible)

*. When the control board presses the confirmation, the message code number lights to display panel of a set panel and the explanation is displayed in the liquid crystal panel. (The buzzer) rings intermittent.

*.When an [error code No.] is displayed, confirm the [message code No.] and investigate according to the following table.

*.The machine can be restored to [normal mode] by turning [on] the [C] key after confirming the content of the [message code].

Error Code

(Display)

Message(state etc.) Sub-message (corresponding method etc.)

M-001

M-002

*.The sewing machine has stopped at a stop position away from the normal UP stop position. *.When the [C] key is turned [ON], the needle rotates in the forward direction and

(Away by more than [+20 degrees] due to the sewing machine pulley.)

[Message] NEEDLE NOT UP POSITION stops at the normal UP stop position.

[Sub Message] MAKE THE NEEDLE A UP POSITION

*.The needle thread trimming detection i nput signal (THS) has been input [ON].

[Message] NEEDLE THREAD BROKEN

*.Thread the needle thread and turn [ON] the [C] key.

[Sub Message] PLEASE PASS THE UPPER THREAD THROUGH THE NEEDLE

M-003

M-004

M-005

*.The presser foot is rising [OFF].

[Message] CLUMP UP POSITION

*.The production number ((UP) counter) has reached the set value.

[Message] UP COUNTER SETTING VALUE UP

*.(DOWN)counter has reached the set value.

[Message] DOWN COUNTER SETTING VALUE UP

*.Lower [ON] the presser foot.

[Sub Message] TURN ON THE FOOT SWITCH (BLACK FOOT SWITCH)

*.Turn [ON] the [C] key (enter key) and cancel.

[Sub Message]

*.Turn [ON] the [C] key (enter key) and cancel.

[Sub Message]

M-006 *.There is no sewing data in the current data area of the internal memory.

[Message] PATTERN DATA NOTHING

*.Turn [ON] the [C] key, and after turn [ON] the [D] key and read the pattern.

[Sub Message] READING OR TEACHING INPUT

[Message] NOT HOME POSITION CAN'T OPERATE

[Message] SERIAL DATA TRANSMITTING...(RS232C)

[Message] SERIAL DATA RECEIVING...(RS232C)

[Message] HALT SW IS PRESSED

[Message] PLEASE RUN SEWING MACHINE

[Message] HALT SW IS PRESSED POWER ON

[Message] NOW KEY LOCK

*.Turn [ON] the [H] key (return key).

[Sub Message] PRESS HOME KEY

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE ROTATE THE HALT SWITCH RIGHT AND TURN OFF

[Sub Message] PLEASE ROTATE THE SEWING MACHINE BY THE WINDER

OR SEWING

[Sub Message] PLEASE TURN OFF THE POWER SUPPLY

[Message] FUNCTION PROHIBITION SETTING (UCC) OF PRESENT VALUE IS ON

[Message] FUNCTION PRO HIBITION SETTING (DCC) OF PRESENT VALUE IS ON

[Message] VALUE IS EXCEEDING THE SET VALUE NOW

[Message] STOPPING AT DWON POSITION

[Message] THE SETTING TABLE NUMBER IS CHANGED

[Sub Message] PLEASE TURN OFF SETTING (UCC) WHEN CORRECTING.

[Sub Message] PLEASE TURN OFF SETTING (DCC) WHEN CORRECTING.

[Sub Message] PLEASE INPUT SMALL VALUE FROM SET VALUE TO PRESENT

VALUE NOW.

[Sub Message] NEEDLE BAR MOVES TO THE UP POSITION WITH NEEDLE

RISE KEY.

[Sub Message] THE SET TABLE NUMBER IS SET IN THIS SEWING DATA

M-019

M-020

M-021

M-028

M-040

M-041

M-042

M-043

M-044

M-050

M-051

M-052

M-053

M-054

M-055

M-056

M-057

M-058

M-059

M-060

M-061

M-062

M-063

M-064

M-065

M-066

[Message] END CODE IN THIS SEWING DATA IS NOT FOUND

[Message] START INPUT SIGNAL IS ON

[Message] CLAMP INPUT SIGNAL IS ON

[Message] It is a termination

[Message] STEP SEQUENCE ILLEGAL SETTING DATA

[Message] STEP DATA NOTHING

[Message] S6 SIGNAL INPUT THEN MACHINE NOT START

[Message] START PROHIBIT SIGNAL INPUT THEN MACHINE NOT START

[Message] COUNT UP THEN MACHINE NOT START

[Message] PRESS HOME KEY

[Message] ILLEGAL SETTING

[Message] TOO LARGE SETTING VALUE

[Message] TOO SMALL SETTING VALUE

[Message] CAN NOT FIND DATA

*.The stitch number exceeds the preset No. of stitches.

[Message] TOO MANY STITCHES

[Message] OUT OF DATA NUMBER

*.A pattern that exceeds the area limit value has been read in.

[Message] OUT OF AREA LIMIT

[Message] TOO SMALL STITCH

[Message] TOO LARGE STITCH

[Message] ALREADY SET SECOND HOME

[Message] DATA WRITING TO MEMORY.....

[Message] TOO LARGE FEED STITCH

[Message] NUMBER OF SKIP JOG IS TOO FEW OR IT IS TOO MANY

[Message] IT WAS NOT POSSIBLE TO OPERATE

[Message] PRESS HOME KEY

[Message] DATA TYPE IS DIFFERENT

[Sub Message] PLEASE ADD END CODE IN INPUT MODE OR MODIFY MODE

[Sub Message] PLEASE TURN OFF START INPUT SIGNAL

[Sub Message] PLEASE TURN OFF CLAMP INPUT SIGNAL

[Sub Message] SEE YOU AGAIN!

[Sub Message] PLEASE CORRECT THE STEP SEQUENCE

[Sub Message] PLEASE MAKE THE STEP SEQUENCE

[Sub Message] PLEASE RELEASE THE S6 SIGNAL.

[Sub Message] PLEASE RELEASE THE START PROHIBIT INPUT SIGNAL.

[Sub Message] PLEASE CLEAR THE COUNTER.

[Sub Message] PLEASE INPUT A CORRECT VALUE

[Sub Message] PLEASE INPUT THE VALUE WITHIN THE RANGE

[Sub Message] PLEASE INPUT THE VALUE WITHIN THE RANGE

[Sub Message] THERE IS NO DATA

*.Decrease the No. of stitches or change [A] mode

[sewing data No. of divisions setting (FLB.)]

[Sub Message] PLEASE DECREASE THE NUMBER OF STITCH

[Sub Message] PLEASE DECREASE THE INPUT POINT

*.Change the following function setting accordingly. Change the [A] mode [sewing

area limit cancel (ALC.)] function to [ON] setting.

[Sub Message] PLEASE MAKE THE DATA IN THE AREA LIMIT

[Sub Message] PLEASE INPUT THE VALUE WITHIN THE RANGE

[Sub Message] PLEASE INPUT THE VALUE WITHIN THE RANGE

[Sub Message] ONLY ONE SECOND HOME POSITION POINT CAN BE INPUT

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE SET FEED WITHIN 0.1-12.0mm

[Sub Message] PLEASE INPUT THE VALUE WITHIN THE RANGE

[Sub Message] PLEASE DECREASE INPUT POINT AND INPUT AGAIN

[Sub Message] PLEASE CONFIRM DATA TYPE

M-077

M-078

M-079

M-080

M-081

M-082

M-083

M-084

M-085

M-086

M-100

M-101

M-102

M-103

M-067

M-068

M-069

M-070

M-071

M-072

M-073

M-074

M-075

M-076

[Message] CURVE DATA WAS NOT ABLE TO BE MADE

[Message] IT IS DURING THE IMAGE DISPLAY PREPARATION.....

[Message] THERE IS THE SECONT HOME POSITION IN THE PATTERN DATA

[Message] CURVE DATA WAS NOT ABLE TO BE MADE FROM INPUT POINT

OR AN OFFSET/MULTIPLE POINT

[Message] THERE IS NO DELETED DATA.

[Message] THE TR IS NOT INPUT AND CANNOT BE ADDED TO THIS POSITION.

[Message] THE SAME CODE AS THE DATA JUST BEFORE IS NOT INPUT OR

CANNOT BE ADDED.

[Message] THE 2HP IS NOT INPUT AND CANNOT BE ADDED TO THIS POSITION.

[Message] THE END IS NOT INPUT AND CANNOT BE ADDED TO THIS POSITION.

[Message] THE CIRCLE OR THE ARC WAS NOT MADE FROM THE INPUT POINT.

[Message]THE MULTIPLE BACK TAKING CANNOT BE SPECIFIED.

[Message] PLEASE PUSH THE HOME KEY. AFTER RETURNING TO HOME POSITION.

[Message] PLEASE PUSH THE HOME KEY. AFTER RETURNING TO HOME POSITION.

[Message] TOO LARGE STITCH

[Message] THERE IS THE SECONT HOME POSITION IN THE PATTERN DATA

[Message] ILLEGAL SETTING

[Message] TRIM CODE CAN NOT BE INPUTTED NOR ADDED JUST AFTER

THE NEEDLE DOWN POSITION STOP CODE.

[Message] NEEDLE DOWN POSITION STOP CODE CAN NOT BE INPUTTED NOR

ADDED JUST BEFORE THE TRIM CODE.

[Message] NEEDLE POSITION IS DEVIATED FROM THE NEEDLE COORDINATES

. CAN NOT OPERATE.

[Message] NEEDLE POSITION IS DEVIATED FROM THE NEEDLE COORDINATES.

CAN NOT OPERATE.

[Message] NOW MAKING DATA

[Message] CALCULATING...

[Message] MAKE ARC DATA?

[Message] MAKE CIRCLE DATA?

[Sub Messa ge] PLEASE INPUT AGAIN REFERRING TO CURVE INPUT NOTES

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE RETURN TO HOME POSITION

[Sub Message] PLEASE REVIEW INPUT POINT

[Sub Message] PLEASE INPUT AND ADD THE TRIM

AFTER SEW

[Sub Message] PLEASE INPUT AND ADD THE 2HP AFTER FEED

[Sub Message] PLEASE INPUT AND ADD THE END AFTER FEED OR TRIM

[Sub Message] PLEASE REVIEW INPUT POINT

[Sub Message]THE MULTIPLE BACK TAKING CAN BE USED ONLY FOR THE

FIGURE WHERE CIRCLE, CURVE, AND BROKEN LINE SHUT.

[Sub Message] PLEASE WAIT FOR A WHILE AFTER PUSHING THE HOME KEY.

[Sub Message] PLEASE WAIT FOR A WHILE AFTER PUSHING THE HOME KEY.

[Sub Message] PLEASE CHANGE THE PATTERN DATA

[Sub Message] PLEASE RETURN TO HOME POSITION

[Sub Message] PLEASE INPUT A CORRECT VALUE

[Sub Message]

[Sub Message]

[Sub Message] PLEASE RETURN TO HOME POSITION

[Sub Message] PLEASE RETURN TO HOME POSITION

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

M-104

M-105

M-106

M-120

M-121

M-122

M-123

M-124

M-125

M-126

M-127

M-128

M-129

M-130

M-140

M-141

M-142

M-143

M-144

M-145

M-146

M-160

M-161

M-162

[Message] MAKE CURVE DATA?

[Message] MAKE BREAK LINE DATA?

[Message] MOVE TO END DATA

[Message] MOVE TO START POINT

[Message] MOVE TO STARTING POSITION

[Message] A SPECIFIED POSITION IS WRONG

[Message] THE AMOUNT OF THE MOVEMENT IS NOT INPUT

[Message] A SPECIFIED POSITION IS WRONG

[Message] A SPECIFIED POSITION IS WRONG

[Message] A SPECIFIED POSITION IS WRONG

[Message] A SPECIFIED POSITION IS WRONG

[Message] A SPECIFIED POSITION IS WRONG

[Message] THE SPECIFIED CODE CANNOT BE DELETED.

[Message] CAN'T FIND SEWING DATA

[Message] CAN'T FIND OFFSET DATA

[Message] CAN'T FIND OVERLAP DATA

[Message] TOO SMALL REDUCTION RATIO

[Message] TOO LARGE ENLARGEMENT RATIO

[Message] THE POINT INPUT DATA CANNOT BE CONVERTED.

[Message] THE POSITION OF START TACKING CANNOT BE CONVERTED

BECAUSE OF THE POINT INPUT DATA.

[Message] THE POSITION OF END TACKING CANNOT BE CONVERTED

BECAUSE OF THE POINT INPUT DATA.

[Message] PLEASE MAKE AREA LIMIT EFFECTIVE

[Message] HALT SW IS PRESSED

[Message] ILLEGAL NUMBER WAS SET

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE SPECIFY FOLLOWING STITCH FROM START POINT

[Sub Message] PLEASE INPUT AMOUNT OF MOVEMENT

[Sub Message] PLEASE SPECIFY SEWING DATA

[Sub Message] PLEASE SPECIFY SEWING AND FEED DATA

[Sub Message] PLEASE SPECIFY ONE STITCH FRONT IS SEW OR FEED DATA

[Sub Message] PLEASE SPECIFY PREVIOUS DATA FROM FINAL STITCH

[Sub Message] PLEASE SPECIFY CODE DATA

[Sub Message] THE TRIM CODE CANNOT BE DELETE WHEN THE FORWARD

ARE SEW OR THE BACK ARE FEED.

[Sub Message] THIS FUNCTION CANNOT BE USED

[Sub Message] THE OFFSET DATA TRANSFORM FUNCTION CANNOT BE

USED

[Sub Message] THE MULTIPLE DATA TRANSFORM FUNCTION CANNOT BE

USED

[Sub Message] PLEASE DO A CORRECT SETTING

[Sub Message] PLEASE DO A CORRECT SETTING

[Sub Message] PLEASE SPECIFY SEWING DATA OTHER THAN THE POINT

INPUT.

[Sub Message] PLEASE SPECIFY SEWING DATA OTHER THAN THE POINT

INPUT.

[Sub Message] PLEASE SPECIFY SEWING DATA OTHER THAN THE POINT

INPUT.

[Sub Message] IT IS DANGEROUS WHEN USING BY THE AREA LIMIT

RELEASE

[Sub Message] PLEASE RELEASE THE HALT SWITCH

[Sub Message] PLEASE SETTING AGAIN

M-163

M-204

M-205

M-206

M-207

M-208

M-200

M-201

M-202

M-203

M-209

M-210

M-211

M-212

M-213

M-220

M-221

M-222

[Message] THE DATA IS BEING CONVERTED INTO A NEW VERSION.

*.FD is not insert to FDD.

*.System software is broken into built in memory.

[Message] FLOPPY DISK ISN'T IN FLOPPY DISK DRIVE

*.The floppy disk is write protected.

[Message] FLOPPY DISK IS WRITE PROTECTED

*.There is an error in the floppy disk.

[Message] FLOPPY DISK ERROR

*. There is a shortage of empty area in the disk.

[Message] AN EMPTY AREA ON FLOPPY DISK IS INSUFFICIENT

*.The specified pattern number could not be found during reading of the pattern from the floppy disk.

[Message] PATTERN DATA ON FLOPPY DISK IS NOT FOUND

[Message] FLOPPY DISK FORMATTING..............

[Message] FLOPPY DISK FORMAT FINISH

[Message] PATTERN DATA IS WRITTEN ON FLOPPY DISK

[Message] PATTERN DATA OF FLOPPY DISK IS BEING DELETED

[Message] PATTERN DATA READING TO FLOPPY DISK.....

[Message] PATTETRN DATA OVER WRITE TO FLOPPY DISK ?

[Message] PATTERN DATA DELETE FROM FLOPPY DISK ?

[Message] CAN THE AMOUNT O F THE HOME CORRECTION BE CONVERTED INTO

THE PATTERN DATA AND ADD ?

[Message] THERE IS NO PERTINENT FILE IN THE FLOPPY DISK.

*.Write in to internal memory is prohibited.

[Message] MEMORY IS WRITE PROTECTED

*. An error has occurred in the internal memory.

[Message] MEMORY ERROR

*.There is a shortage of internal memory empty area.

[Message] MEMORY IS PATTERN DATA FULL

[Sub Message] PLEASE WAIT FOR A WHILE

*. Confirm the floppy disk set in.

*.Read the system software.

[Sub Message] PLEASE INSERT THE FLOPPY DISK.

*.Confirm the floppy disk and cancel the unlock the write protection ore use another

floppy disk.

[Sub Message] PLEASE RELEASE THE WRITE-PROTECTION OF THE

FLOPPY DISK.

*.Use a new floppy disk.

[Sub Message] PLEASE EXCHANGE THE FLOPPY DISK OR FORMAT.

*.Check the floppy disk.

[Sub Message] PLEASE EXCHANGE THE FLOPPY DISK OR DELETE T HE FILE.

*.Confirm the specified pattern number and execute read in again.

[Sub Message] PLEASE CONFIRM THE FILE NAME AND THE SEWING DATA

NUMBER.

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] FORMER DATA IS DELETED WHEN OVERWRITING.

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] RETURN TO HOME POSITION AFTER WRITING ENDS.

[Sub Message] PLEASE CONFIRM THE FILE OF THE FLOPPY DISK.

*.Change the [on] setting of [A] mode [internal memory write in prohibit (PFL.)]

function to [of].

[Sub Message] PLEASE RELEASE WRITE-PROTECTION WHEN WRITING.

*.Return to [normal mode] by turning [on] the [C] key Execute the same operation

again. If message code [M-11] is displayed again, copy the other parts of the

internal memory onto a floppy disk and reformat the internal memory.

[Sub Message] PLEASE FORMAT AN INTERNAL MEMORY.

*.Delete unnecessary patterns or change [A] mode [sewing data No. of divisions

setting ]FLB.)].

[Sub Message] PLEASE DELETE THE SEWING DATA NOT USED.

M-223

M-224

M-225

M-226

M-227

M-228

M-229

M-230

M-231

M-232

M-233

M-234

M-235

M-236

M-237

M-238

M-239

M-240

M-241

M-242

M-243

M-244

M-245

M-246

*.The specified patter number was not found during reading of the pattern from

the internal memory.

[Message] PATTERN DATA ON MEMORY IS NOT FOUND

[Message] MEMORY FORMATTING..................

[Message] MEMORY FORMAT END

[Message] PARTITION No. OF MEMORY IS ILLEGAL

[Message] PATTERN DATA WRITING TO MEMORY.....

[Message] PATTERN DATA DELETING TO MEMORY.....

[Message] PATTERN DATA READING TO MEMORY.....

[Message] PATTERN DATA DELETE FROM MEMORY ?

[Message] PATTERN DATA OVER WRITE TO MEMORY ?

[Message] MEMORY AREA OVER

[Message] MEMORY BROKEN

[Message] PATTERN DATA NOT DELETE (THIS PATTERN DATA IS USING)

[Message] MEMORY FORMAT OK ?

[Message] FD FORMAT OK ?

[Message] WRITING PROHIBITION IN THE INTERNAL MEMORY.

[Message] THERE IS THE SECOND HOME POSITION IN THE PATTERN DATA

[Message] THE AMOUNT OF THE HOME CORRECTION IS WRITTEN ON THE DATA

[Message] OUT OF AREA LIMIT

[Message] WRONG PATTERN DATA WAS SET

*.Read protect without home position.

[Message] NOT POSSIBLE TO READ EXCLUDING HOME POSITION

*.Write protect without home position.

[Message] NOT POSSIBLE TO WRITE EXCLUDING HOME POSITION

[Message] TOO MANY STITCHES

[Message] NOW CHECK SUM.....

[Message] INPUT FILE NAME

*.Confirm the specified pattern number and execute reading again.

[Sub Message] PLEASE CONFIRM THE FILE NAME AND THE SEWING DATA

NUMBER.

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] FORMER DATA IS DELETED WHEN OVERWRITING.

[Sub Message] DELETE THE NEEDLESS PATTERN DATA THEN RETRY

THE FUNCTION.

[Sub Message] THE MEMORY BREAKS. PLEASE INSTALL THE SYSTEM

AGAIN.

[Sub Message] THE SELECTED SEWING DATA IS USED NOW.

[Sub Message] ALL THE SEWING DATA OF AN INTERNAL MEMORY IS

DELETED.

[Sub Message] ALL THE SEWING DATA OF THE FLOPPY DISK IS DELETED.

[Sub Message] RELEASE THE INTERNAL MEMORY READ-ONLY SETTING

WHEN WRITING.

[Sub Message] PLEASE CHANGE THE PATTERN DATA

[Sub Message] WHEN >< IS SELECT,USUAL IS WRITTEN

[Sub Message] PLEASE CHANGE THE SEWING DATA.

[Sub Message] PLEASE CHANGE THE SEWING DATA.

*.Press the [RESET]key.

[Sub Message] PLEASE RETURN TO HOME POSITION

*.Press the [RESET]key.

[Sub Message] PLEASE RETURN TO HOME POSITION

[Sub Message] PLEASE CHANGE THE SEWING DATA.

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE INPUT THE FILE NAME BY 8 CHARACTERS OR LESS

M-273

M-274

M-275

M-276

M-277

M-278

M-279

M-280

M-281

M-247

M-248

M-250

M-251

M-252

M-270

M-271

M-272

M-300

M-301

M-302

M-303

M-304

M-305

M-306

M-307

M-308

[Message] ILLEGAL SETTING PATTERN NO.

[Message] THE LIMIT OF THE SEWING AREA IS EXCEEDED

[Message] THE PASSWORD IS DIFFERENT

[Message] IT HAVE CHANGED THE SETTING FOR LCD PANEL.

[Message] PLEASE CLEAR CURRENT COMBINATION FORM

[Message] Please put oil to the machine head

[Message] Please clean up the sewing machine and around the hook

[Message] Please exchange the V-belt / exchange the timing-belt

[Message] Please do the maintenance of the machine

[Message] Please exchange the bobbin

[Message] Exchanging the bobbin now

[Message] There is no bobbin

[Message] Trouble 1 occurred

[Message] Trouble 2 occurred

[Message] Trouble 3 occurred

[Message] Trouble 4 occurred

[Message] Trouble 5 occurred

[Message] PATTERN DATA COPYING FLOPPY DISK TO MEMORY...

[Message] PATTERN DATA COPYING MEMORY TO FLOPPY DISK...

[Message] PASSWORD IS DIFFERENT

[Message] FLOPPY DISK IS NOT INSERTED

[Message] WRITING IS PROHIBITED IN THE FLOPPY DISK

[Message] FLOPPY DISK IS DAMAGED

[Message] AN EMPTY AREA ON THE FLOPPY DISK IS INSUFFICIENT

[Message] MAY I OVERWRITE THE PATTERN DATA ON THE FLOPPY DISK ?

[Message] FLOPPY DISK IS NOT INSERTED

[Sub Message] PLEASE INPUT THE CORRECT SEWING DATA NUMBER.

[Sub Message] IT IS DANGEROUS. PLEASE CHANGE THE NEEDLEWORK

DATA

[Sub Message] PLEASE INPUT AGAIN

[Sub Message] PLEASE TURN OFF THE POWER SUPPLY

[Sub Message] CURRENT COMBINATION FORM IS CLEARD BY PRESSING

CLR BUTTON

[Sub Message]

[Sub Message]

[Sub Message]

[Sub Message]

[Sub Message]

[Sub Message] please don't close your hand

[Sub Message] please set the bobbin to the cassette case

[Sub Message] please attention

[Sub Message] please attention

[Sub Message] please attention

[Sub Message] please attention

[Sub Message] please attention

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE INPUT AGAIN

[Sub Message] PLEASE INSERT THE FLOPPY DISK.

[Sub Message] PLEASE RELEASE THE WRITE-PROTECTION OF THE FLOPPY

DISK.

[Sub Message] PLEASE EXCHANGE THE FLOPPY DISK OR FORMAT.

[Sub Message] PLEASE EXCHANGE THE FLOPPY DISK OR DELETE THE FILE.

[Sub Message] FORMER DATA IS DELETED WHEN OVERWRITING.

[Sub Message] PLEASE INSERT THE FLOPPY DISK.

M-309

M-310

M-311

M-312

M-313

M-314

M-315

M-316

M-317

M-318

M-319

M-320

[Message] THERE IS NO PATTERN DATA

[Message] FINISHED READ PLEASE TURN OFF POWER SUPPLY

[Message] THE TABLE FILE IS BEING READ

[Message] THE STEP FILE IS BEING READ

[Message] THE CLEARNESS AT THE MULTIPLICATION TIME ENDED.

[Message] THE TABLE NUMBER OF THE COPY AHEAD IS BEING USED NOW.

[Message] MAY I COPY THE SPECIFIED PATTERN DATA?

[Message] MAY I COPY ALL THE PATTERN DATA?

[Message] MAY I OVERWRITE THE COMBINATION DATA?

[Message] MAY I CLEAR PATTERN DATA OF COMBINATION DATA?

[Message] milling cutter is in lower position in this sewing data

[Message] Setting has been changed. Please turn the power off

[Sub Message] PLEASE INSERT THE FLOPPY DISK WHICH READ FILE

ENTERED.

[Sub Message] RECLOSING OF POWER SUPPLY IS NECESSARY TO USE

CONTINUOUSLY.

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] PLEASE WAIT FOR A WHILE

[Sub Message] OVERWRITES SETTING

[Sub Message] OVERWRITES,THERE'S PAT DATA OF SAME No., FORMER

DATA IS DEL

[Sub Message] OVERWRITES,THERE'S PAT DATA OF SAME No., FORMER

DATA IS DEL

[Sub Message] FORMER DATA IS DELETED WHEN OVERWRITING.

[Sub Message]

[Sub Message] Please return to home position after the milling cutter goes up.

[Sub Message]

[14]Unit wiring diagram

( 1).Outside of control box

Other voltage refer to "[15]Several power supply"

Control box

Model name

PLK-E-CU -20

CONB

Control box main power supply

Control box

CONA

Main motor

CONC

Stepping motor

COND

Output of solenoid

CONE

RS-232C

CONF

Teaching panel

CONG

Input/output

Input signal

CONI

Foot switch

640582-1

350689-1

Detector

To CABLE1

60-9090-306-108-005

60-9090-0423-99-805

60-9090-304-218-006

60-9090-0322-99-805

60-9090-304-118-006

60-9090-0322-00-805

Foot switch

Teaching panel

(option)

Pushbutton switch assay

BM090C349G01

60-9090-304-118-006

60-9090-0322-00-805

Main motor

Stepping motor X

172339-1

170359-1

X home sensor(E2S-W23)

172331-1

170361-1

350780-1

2P-4P 350689-1

1P 350690-1

350779-1

2P-4P 350690-1

1P 350689-1

X

Y

350780-1

1,2,4P 350689-1

3P 350690-1

350780-1

1,2,4P 350689-1

3P 350690-1

PLK-E-CON P.W.B

CON2

CON1

CON5

+12V

Y home sensor

0V

0V

CON4

+12V

X home sensor

0V

CABLE1

770372-1

CON3

350417-1

To detector

I4(Halt)

0V

+12V

O6(Buzzer)

CON7

+24V

O1(Trim)

172160-1

To main motor encoder

170362-1 CON8

+24V

CABLE2 O4(Clamp)

X

Stepping motor Y

Y home sensor

(E2S-W23)

Y

1

2

3

4

1

2

3

1

2

3

4

1

2

1

2

3

4

1

2

1

2

3

1

2

3

4

1

2

1

2

TE1 TE2

CON9

CON10

CON11

+24V

N.C.

O2(Wiper)

+24V

O3 (Thread release)

+24V

N.C.

O5 (Presser foot)

1

2

3

1

2

1

2

3

1

2

1

2

3

1

2

3

171822-4

170204-1

60-8263-3028-16-000

60-8263-0617-00-808

5195-02-BU

5225TL

5197-02

5225TL

5195-03

5225TL

5196-02-BU

5225TL

5197-03

5225TL

172339-1

170359-1

To CABLE2

60-8263-3048-15-001

60-8263-0513-00-808

60-8263-3038-15-000

60-8263-0513-00-808

1

2

T

1

2

Halt switch

Bz

60-8263-3028-15-000

60-8263-0513-00-808

Trim

FU

W

L

PF

Clamp

Wiper

Presser foot

Buzzer

Tread release

Into sewing machine head

770361-1

350418-1

(2).Inside of control box

Control box

FDD

CON2

PLK-B-DISP

P.W.B

CON1

Model name PLK-E-CU -20

Transformer

Grey Orange

Orange

Brown

Blue Black

Black

(BKO-E3160H01)

CON1

CON3

Brake register

MFS30A

101K

100ohm

XC-E2-1B-PLK

P.W.B

CON1

To PLK-B1-PCCON

P.W.B CON1

PLK-B1-PMD-E P.W.B

CON6

CON5

CON3

CON5

CON9 CON5

PLK-B1-CPU-E P.W.B

CON10

CONB

Control box main power supply

CONA

Main motor

CONC

Stepping motor

COND

Output of solenoid

CONE

RS-232C

CONF

Teaching panel

CONG

Input/output signal

CONH

Input signal

CONI

Foot switch

[15]Several power supply

1. 3phi AC200V -- 240V 50/60Hz

Red

White

Black

Green

OFF ON

60-9090-306-108-002

Push button switch assay

M090C349G03

Red

White

Black

Green

Green

1

2

3

4

5

6

To control box CONB

Power unit

model name PLK-B-PUC-B40

2.3phi AC380V -- 415V 50/60Hz (Except Europe)

Black

Brow

Blue

Green/

Yellow

OFF ON

Push button switch assay

M090C349G08

60-9090-306-108-002

Black

Blue

Green

Green/

Yellow

60-9090-306-208-002

1

2

3

4

5

6

1

2

3

4

5

6

Black

Blue

3-phase transformer 3phi 800VA

BKO-E3138H02

F1

5A

Black k

Brow n

U

V

Blue

W

F2

5A

Green/ Yellow

Green/ Yellow

Ground u v w

Blac k

Red

Blue

60-9090-304-118-006

60-9090-305-108-005

Black

Red

Blue

Green/

Yellow

1

2

3

4

1

2

3

4

Blac k

Green/

Yellow

60-9090-304-218-006

60-9090-304-118-006

1

2

3

4

5

1

2

3

4

5

Black

Brown

Blue

Green/

Yellow

Black

Brown

Green/

Yellow

Green/

Yellow

1

2

3

4

5

6

To control box

CONB

60-9090-306-108-005

3.1phi AC100V -- 120V 50/60Hz

White te

Black

Green

OFF ON

Push button switch assay

M090C350G05

60-9090-306-108-005

Power unit

model name PLK-B-PUC-A10

Single-phase transformer 1phi 600VA

BKO-E3140H03

Black

100V

200V Black

White te

Black

Green

1

2

3

4

5

6

Green

1

2

3

4

5

6

Black

Brown

F1

20A 0V 0V

Red

60-9090-306-108-005

Green/ Yellow

Green/

Ground

60-9090-304-108-005

1

2

3

4

1

2

3

4

Black

Brown

Blue

Green/ Yellow

60-9090-304-218-006

60-9090-305-208-005

60-9090-305-108-005

1

2

3

4

5

1

2

3

4

5

Black

Blue

Green/

Yellow

Black

Brown

Blue

Green/

Yellow

Green/

Yellow

1

2

3

4

5

6

To control box

CONB

60-9090-306-108-005

4.1phi AC200V -- 240V 50/60Hz (Europe)

Blue

Brown

Green/

Yellow Push button switch assay

M090C433G02

60-9090-306-108-005

Blue

Brown

Green

1

2

3

4

5

6

Green/

Yellow

60-9090-306-208-005

Noise filter unit

model name

PLK-E-NU-20

60-9090-304-118-006

Ferrite core

PLK-B1-FIL P.W.B

1

2

3

4

5

6

Black

Brown

Blue

Green/ Yellow

Black

Brown

Blue

Green/ Yellow

1

2

3

4

1

2

3

4

Green/

Yellow

Ground

Black

Brown

Blue

Green/

Yellow

1

2

3

4

5

60-9090-305-208-005

60-9090-305-108-005

1

2

Black

Brown

3

4

5

Blue

Green/

Yellow

Black

Brown

Green/

Blue

Yellow

Green/

Yellow

1

2

3

4

5

6

To control box

CONB

60-9090-306-108-005

5.1phi AC200V -- 240V 50/60Hz (Except Europe)

Blue

Brow n

Yellow

OFF

O

ON

O

Push button switch assay

M090C433G02

60-9090-306-108-005

Blue

Brown

Green

Green/

Yellow

1

2

3

4

5

6

To control box

CONB

Control box connectors layout

[16] Control box connectors layout

①

②

③

④

Main motor

(Connect to main motor)

Stepping motor

(Connect to stepping motoring sewing machine head)

CONC

COND

CONA

⑤

⑥

⑦

⑧

①

②

③

④

⑨

⑩

⑪

⑫

⑬

⑭

⑮

⑤

⑥

⑦

⑧

①

②

③

④

Output of solenoid

(Connect to dewing machine head)

CONB

①

②

③

④

⑤

⑥

Rear view of control box

[16]-1

⑥

①

⑧

④

②

⑦

③⑤

Control box main power supply

(Connect to push button switch or power unit or noise filter unit)

①

④

②

③⑤

・

・

・

・

①

③

⑤

⑦

・

・

・

・

・

②

④

⑥

⑧

・

CONE

CONF

RS-232C

(option)

Teaching panel

(option)

・

・

・

・

・

①

③

⑤

⑦

・

・

・

・

・

②

④

⑥

⑧

①

・

・

・

・

③

⑤

⑦

・

②

・

・

・

・

④

⑥

⑧

・

CONG

Input/output signal

CONH

Input signal

(Connect to sewing machine head)

CONI

Foot switch

(Connect to foot switch)

[17]Pin No. of connectors

1.Main motor (CONA)

Signal

U

V

W

PE

Pin No.

1

2

3

4

2.Control box main power supply (CONB)

Signal Pin No.

Table1-1

R

S

T

-

E

PE

+12V

RXD

N.C.

TXD

GND

7.Teaching panel (CONF)

Signal

R0

VP5

R1

0V

R2

0V

R3

-9V

R4

E

R5

R/W

R6

A0/RS

R7

PD8

S0

PD9

S1

PD10

S2

PD11

+12V

PD12

OA0

PD13

OA1

PD14

OA2

PD15

OA3

DIR

VP5

NOE

N.C.

N.C.

1

2

3

4

5

6

3.Stepping motor (CONC)

Signal Pin No.

XAN 1

XAP

XBN

2

3

XBP

YAN

4

5

YAP

YBN

6

7

YBP 8

5.RS-232C (CONE)

Signal Pin No.

1

2

3

4

5

15

16

17

18

11

12

13

14

7

8

9

10

29

30

31

32

25

26

27

28

33

34

35

36

19

20

21

22

23

24

Pin No.

1

2

3

4

5

6

4.Out of solenoid (COND)

(Same as PLK-B1-CON P.W.B CON2.)

Table1-2

Signal

O1

O3

O5

OB

O9

O7

O6

+24V

O2

O4

OC

OA

O8

OSC2

+24V

6.Foot switch (CONI)

Signal

Table1-3

+12V

I1

I2

I3

GND

GND

N.C.

GND

E

Initial setting

Trim

Thread release

Presser foot

Function output 1

Function output 3

Virtual output 1

Buzzer

-

Wiper

Clamp

Clamp2 output

Function output 2

Virtual output 1

-

-

Initial setting

-

Start

Clamp1

Nothing

-

-

-

-

-

8.Input signal (CONH)

(Same as PLK-B1-CON P.W.B CIN2.)

Table1-5

Table1-7

I9

ID

UP

DN

PG

EA

EB

IE

IG

IF

IH

0V

0V

Signal

+12V

+5V

I4

I5

I6

IA

I7

IB

I8

IC

X home sensor

Y home sensor

N.C.

Y home sensor

-

-

-

-

-

-

-

-

Needle thread sensor

Clamp2 input

-

-

5

6

7

8

Body

1

2

3

4

11

12

13

14

15

7

8

9

10

Pin No.

1

2

3

4

5

6

Pin No.

Initial setting

-

-

Halt

Nothing

Nothing

Nothing

Nothing

Nothing

Nothing

Needle up/down

X home sensor

Thread trimming protect

Clamp step forward

Table1-4

Table1-6

Pin No.

1

2

3

4

5

10

11

12

13

6

7

8

9

18

19

20

21

22

23

24

25

26

14

15

16

17

[17]-1

Table1-8

Pin No. of connectors

How to use the terminal 1,2 and connectors

[18]How to use the terminal 1,2 and connectors

+12V

+12V

IA

+12V

IB

+12V

IC

+12V

ID

0V

I5

0V

I6

0V

I7

0V

I8

0V

I9

+12V

0V

OH

OI

OJ

OK

OL

OM

ON

OO

IK

IL

IM

IN

0V

0V

II

IJ

IO

IP

0V

OD

OE

OF

OG

+12V

+12V

1.Input/output signal (CONG)

-

-

Jog +

Jog -

Reset

Winding

Trim prohibit

Wiper prohibit

Nothing

Nothing

-

-

Nothing

Nothing

Nothing

Nothing

Nothing

Nothing

Down position

Error

Operation preparation completion

Halt in progress

Sewing completion

Home position

-

-

2.Terminal 1 (Into sewing machine head)

12

13

14

15

8

9

10

11

16

17

18

19

20

4

5

6

7

1

2

3

21

22

23

24

25

26

-

Nothing

-

Nothing

-

Nothing

-

Nothing

-

Virtual input 0

-

-

-

Nothing

-

Nothing

-

Needle up/down

-

Virtual input 1

A8

A9

A10

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

A1

A2

A3

A4

A5

A6

A7

Table2-1

Table2-2

L

L

Switch

Output

Power supply +12V of CONG, Terminal 1,2 maximum 300mA.

If you want to more ampere, put on power supply to outside of control box.

Needle thread

Trimming sensor

0V

IG

+12V

3.Terminal 2 (Into sewing machine head)

No.

Switch

Thread trimming

IE protect

A1

0V - A2

IF Clamp2 input A3 Output

O6

O7

Buzzer

Virtual output 1

A4

A5 L

O8

O9

Virtual output 0

Function output 3

A6

A7

Function output 2

Bz

OA

OB

OC

IG

Function output 1

A8

A9

A10

B1

L

+12V

IH

+24V

+24V

Clamp2 output

Needle thread trimming sensor

-

Clamp step forward

-

-

B2

B3

B4

B5

+24V

+24V

+24V

+24V

OSC2 -

-

-

-

-

B6

B7

B8

B9

B10

Table2-3

[18]-1

Table of connection into control box

[19]Table of connection into control box

1.CPU -- PMD *( ) Initial setting

CON10-1 Z11

CON10-7 ZI11

CON10-9 SOL-OC

CON3-1 CON10-2 Z12Ｚ１２

CON3-7 CON10-8 RESERV

CON3-2

*CPU…..

PLK-B1-CPU-E P.W.B

*PMD…..

PLK-B1-PMD-E P.W.B

*XC-E…..

XC-E2-1B-PLK P.W.B

*DISP…… PLK-B-DISP P.W.B

CON3-8

*CONB….

Control box main power supply

CON3-10

*FDD……

Floppy disk driver

CON10-13 O6(Buzzer)

CON10-15 O8 (Virtual output 0)

CON3-15 CON10-16

CON10-17 OA (Function output 2 )

CON3-17 CON10-18

(Function output 3)

CON10-19 OC (Clamp 2 output)

CON3-19 CON10-20

(Function output 1)

CON10-21 O3 (Thread release)

CON3-21 CON10-22

CON10-23 O4 (Clamp 1 output)

CON3-23 CON10-24

CON10-25 Z21

CON10-27 YI22

CON3-25 CON10-26 ZI21

CON3-27 CON10-28 Z22

CON10-29 Y22

CON10-31 YI12

CON10-33 Y12

CON10-35 XI22

CON3-29 CON10-30 YI21

CON3-31 CON10-32 Y21

CON3-33 CON10-34 YI11

CON3-35 CON10-36 Y11

CON10-37 X22

CON10-39 XI12

CON10-41 X12

CON10-43 X11

CON10-45 XPD

CON10-47 RA

CON3-37 CON10-38 XI21

CON3-39 CON10-40 X21

CON3-41 CON10-42 XI11

CON3-43 CON10-44 PMD-OC

CON3-45 CON10-46 YPD

CON3-47 CON10-48 ZPD

CON3-14

CON3-16

CON3-18

CON3-20

CON3-22

CON3-24

CON3-26

CON3-28

CON3-30

CON3-32

CON3-34

CON3-36

CON3-38

CON3-40

CON3-42

CON3-44

CON3-46

CON3-48 Table 3-1

2.PMD -- FDD

PMD Signal FDD

CON7-1 FD5V

CON7-2 N.C.

CON7-3 N.C.

CON7-4 N.C.

CON2-1

CON2-2

CON2-3

CON2-4

Table 3-2

3.XC-E -- Main motor

XC-B Signal CONA

CON3-1 U

CON3-2 V

CON3-3 W

- PE

CONA-1

CONA-2

CONA-3

4.1 PMD -- XC-B (CON5 connection)

PMD Signal XC-B

CON1-1 W3

CON1-2 -

CON1-3 W2

CON1-4 W1

CON5-4

CON5-3

CON5-2

CON5-1

Table 3-4.1

4.2 PMD -- XC-E (CON6 connection)

PMD Signal XC-B

CON1-1 W3

CON1-2 -

CON1-3 W2

CON1-4 W1

CON6-4

CON6-3

CON6-2

CON6-1

Table 3-4.2

[19]-1

Table of connection into control box

５．ＣＰＵ ～ ＦＤＤ間

ＣＰＵ

Signal

CON5-1 GND

CON5-3 GND

CON5-5 GND

CON5-7 GND

CON5-9 GND

CON5-11 GND

CON5-13 GND

CON5-15 GND

CON5-17 GND

CON5-19 GND

CON5-21 GND

CON5-23 GND

CON5-25 GND

CON5-27 GND

CON5-29 GND

CON5-31 GND

CON5-33 GND

6.CPU -- DISP

ＦＤＤ ＣＰＵ

Signal

ＦＤＤ

CON1-5 CON5-6 DS3

CON1-7 CON5-8 INDEX

CON1-11 CON5-12 DS1

CON1-13 CON5-14 DS2

CON1-4

CON1-6

CON1-8

CON1-10

CON1-12

CON1-14

CON1-15 CON5-16 MOTOR CON1-16

CON1-18

CON1-19 CON5-20 STEP

CON1-25 CON5-26 TRKO

CON1-20

CON1-22

CON1-24

CON1-26

CON1-33 CON5-34 READY

CON1-28

CON1-30

CON1-32

CON1-34

Table 3-5

CON1-2

CON1-4

CON1-6

CON1-8

CON1-10

CON1-12

CON1-14

CON1-16

CON1-18

CON1-20 Table 3-6

CON9-1 +5V

CON9-3 +12V

CON9-5 Data bass I/O

CON9-7 Data bass I/O

CON9-9 Data bass I/O

CON9-11 Data bass I/O

CON9-13 DIR/RD

CON9-15 A0/RS

CON1-1 CON9-2 +5V

CON1-3 CON9-4 +12V

CON1-5 CON9-6 Data bass I/O

CON1-7 CON9-8 Data bass I/O

CON1-9 CON9-10 Data bass I/O

CON1-11 CON9-12 Data bass I/O

CON1-13 CON9-14 R/W/WR

CON1-15 CON9-16 A1

CON9-19 GND CON1-19 CON9-20 GND

7.CPU -- XC-B

CPU Signal XC-B

CON6-1 RA

CON6-2 IFV

CON6-3 IFU

CON6-4 WN

CON6-5 UN

CON6-6 VN

CON6-7 BKS

CON6-8 ER

CON6-9 VP

CON6-10 WP

CON6-11 UP

CON6-12 COM

CON6-13 VDC

CON6-14 +12V

CON6-15 GND

CON1-1

CON1-2

CON1-3

CON1-4

CON1-5

CON1-6

CON1-7

CON1-8

CON1-9

CON1-10

CON1-11

CON1-12

CON1-13

CON1-14

CON1-15

Table 3-7

8.PMD -- Transformer (BKO-E3160H01)

Black

CON5-2 - -

Black

Table 3-8

9.PMD -- Transformer (BKO-E3160H01)

PMD Signal

Orange

CON9-2 - -

Table 3-9

Orange

[19]-2

10.1 XC-E -- Transformer (BKO-E3160H01) (CO5 connection)

PMD Signal Transformer

CON5-1 0V

CON5-2 -

CON5-4 -

-

AC210V

Table 3-10.1

AC230V

10.2 XC-E -- Transformer (BKO-E3160H01) (CO6 connection)

PMD Signal Transformer

CON6-1 0V

CON6-2 -

CON6-3 -

-

AC230V

11.XC-E -- CONB

XC-E Signal CONB

CON4-1 E

CON4-2 T

CON4-3 S

CON4-4 R

CONB-5

CONB-3

CONB-2

CONB-1 Table 3-11

- PE

12.XC-E -- Break register

CONB-6

Table 3-12

[19]-3

Table of connection into control box

Specification / Table of digital display

[20] Specifications

Power source

Specifications

Power unit

100 - 200V single phase

50/60Hz

PLK-B-PUC-A1

0

200 - 240V single phase

3-phase

50/60Hz

－

200 - 240V single phase

3-phase

(Europe)

50/60Hz

380 - 415V

3-phase

50/60Hz

PLK-B-PUC-B4

0

Noise filter unit

PLK-E-NU

Model name

Rated output

XL-554-20Y

550W

Main motor

Rated speed

Rated torque

Model name

3,000 rpm

1.76N.m(0.18kgm)

PLK-E-CU-20

Control box

Condition

Rated output

Power source

Range of rating

Voltage

Ambient temperature

Ambient humidity

DC 24V

1 KVA

10%

5 degrees(c) - 35 degrees(c)

45％ - 85％

Please use the Noise Filter Unit "PLK-E-NU", in order to conform

the requirements of the EC EMC Directive (89/336/EEC).

[21] Table of digital display

Numeral 0 1 2 3 4 5 6 7 8 9

Digital display

A B C D E F G H I J

Characters

Digital display

Characters

Digital display

Characters

U V W X Y Z

Digital display

K L M N O P Q R S T

[20, 21]-1

MITSUBISHI ELECTRIC CORPORATION

FACTORY AUTOMATION SYSTEM

OFFICE TOWER “Z” 14F 8-12 1chome, Harumi CHUO-KU, TOKYO 104-6212, JAPAN

Phone : +81-3-6221-6060 Fax : +81-3-6221-6076

New publication, effective APR.2003.

Specifications subject to change without notice.