Philips SHB9150RD/00 User manual
Add to my manuals
14 Pages
Philips SHB9150 wireless on-ear headset lets you enjoy convenient hands-free calls, wireless music, switch between calls and music, and enjoy music on non-Bluetooth devices with an audio cable.
advertisement
Always there to help you
Register your product and get support at www.philips.com/welcome
Contact
Philips
SHB9150
User manual
Contents
1 Important safety instructions
2 Your Bluetooth stereo headset
Overview of your Bluetooth stereo headset 3
3 Get started
Pair the headset with your mobile phone 4
4 Use your headset
Connect the headset to a Bluetooth device 6
5 Technical data
7 Frequently asked questions
6 Notice
Disposal of your old product and batteries 9
Notice for the European Union 10
EN
1
1 Important safety instructions
Hearing Safety
Danger
•
To avoid hearing damage, limit the time you use the headset at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.
Be sure to observe the following guidelines when using your headset.
• Listen at reasonable volumes for reasonable periods of time.
• Be careful not to adjust the volume continuously upwards as your hearing adapts.
• Do not turn up the volume so high that you can’t hear what’s around you.
• You should use caution or temporarily discontinue use in potentially hazardous situations.
• Excessive sound pressure from earphones and headset can cause hearing loss.
• Using the headset with both ears covered while driving is not recommended and may be illegal in some areas while driving.
• For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.
General information
To avoid damage or malfunction:
Caution
•
Do not expose the headset to excessive heat.
•
Do not drop your headset.
•
Headset shall not be exposed to dripping or splashing.
•
Do not allow your headset to be submerged in water.
•
Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
•
If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
•
The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
About operating and storage temperatures and humidity
• Operate or store in a place where temperature is between -15ºC (5ºF) and
55ºC (131ºF) (up to 90% relative humidity.
• Battery life may be shorter in high or low temperature conditions.
Compliance with EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.
2
EN
2 Your Bluetooth stereo headset
Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.
With this Philips wireless on-ear headset, you can:
• enjoy convenient wireless handsfree calls;
• enjoy and control wireless music;
• switch between calls and music;
• enjoy music on non-Bluetooth devices with an audio cable.
What's in the box
Philips Bluetooth stereo headset SHB9150
USB charging cable
Audio cable
Quick start guide
Other devices
e
Volume/Track control a
A mobile phone or device (e.g. notebook, PDA,
Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset.
Overview of your Bluetooth stereo headset
e d
Call/Music button b
Microphone c
Audio input jack d
Charging slot a b c
EN
3
3 Get started
Charge your headset
Note
•
Before you use your headset for the first time, charge the battery for 5 hours for optimum battery capacity and lifetime.
•
Use only the original USB charging cable to avoid any damage.
•
Finish your call before charging the headset, as connecting the headset for charging will power the headset off.
Connect the supplied USB charging cable to:
• the USB connector of the headset and;
• USB power source.
» LED turns white during charging and turns off when the headset is fully charged.
Tip
•
Normally, a full charge takes 3 hours.
•
When your battery is empty, you can carry on listening music with an audio cable. Make sure the headset is off
(and not in idle mode) before using this audio cable.
Pair the headset with your mobile phone
Before you use the headset with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headset and mobile phone. The headset stores the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest paired device is replaced by the new one.
There are two ways to pair your headset with your mobile phone:
4
EN
• Manual pairing
• NFC pairing
Manual pairing
1
Make sure that the mobile phone is turned on and its Bluetooth feature is activated.
2
Make sure that the headset is fully charged and turned off.
3
Press and hold until the blue and white
LED flashes alternately.
»
The headset remains in pairing mode for 5 minutes.
4
Pair the headset with the mobile phone.
For detailed information, refer to the user manual of your mobile phone.
NFC pairing
1
Make sure that the mobile phone is turned on.
2
Make sure that the headset is fully charged and turned off.
3
Press and hold until the blue and white
LED flashes alternately..
4
Make sure you turn on the NFC function on your phone and your phone’s screen remains active.
5
Place your phone over the headset so that the NFC detection area of each device can touch each other.
Note
•
Make sure your mobile phone has the NFC feature available and switched on.
•
Make sure your mobile phone is not in standby mode.
•
Pairing with NFC is only suitable for Android mobile operating system 4.2 or above.
•
Refer to the user manual of your mobile phone to identify its NFC detection area.
The following example shows you how to pair the headset with your mobile phone.
1
Activate the Bluetooth feature of your mobile phone, select Philips SHB9150.
2
Enter the headset password "0000" (4 zeros) if prompted. For those mobile phones featuring Bluetooth 3.0 or higher, no need to enter a password.
Add
Bluetooth device
Settings
Bluetooth
Select
10:35
Connectivity
Back
Settings
Devices Found
Select
10:36
Philips SHB9150
Settings
Select
10:37
Connectivity
Enter Password
Back Back
****
0000
EN
5
4 Use your headset
Connect the headset to a
Bluetooth device
1
Turn on your mobile phone/Bluetooth device.
2
Press and hold to turn the headset on.
»
The blue LED flashes.
» The headset is reconnected to the last connected mobile phone/
Bluetooth device automatically. If the last one is not available, the headset tries to reconnect to the second last connected device.
Tip
•
If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headset, you have to reconnect the headset and mobile phone/Bluetooth device manually.
Note
•
If the headset fails to connect to any Bluetooth device within range in 5 minutes, it will switch off automatically to save the battery life.
Automatic power saving
If the headset fails to connect any
Bluetoothdevice within range in 5 minutes, it powers down automatically to save the battery life.
Manage your calls and music
Call/Music button
Task
Turn the headset on.
Turn the headset off.
Operation Sound or LED indicator
Press and hold for 1 second.
• 1 short beep
• 3 white flashes: battery low <
25%
• 2 white flashes: battery level <
50%
• 1 blue flash: battery level >
50%
Press and hold for 4
• 1 long beep
• 1 long white seconds.
flash
Press once. 1 short beep Play or pause music.
Pick up/ hang up a call.
Reject an incoming call.
Redial the last number.
Switch caller during a call.
Press once. 1 short beep
Press and hold for 1
1 short beep second.
Press twice. 1 short beep
Press twice.
Volume/Track control button
1 long beep
Adjust volume.
Skip forward.
Skip backward.
Mute/unmute the microphone in a call.
Slide up/ down
N/A
Press once 1 short beep
Press twice 1 short beep
Press once
2 short beeps
6
EN
Other headset indicator status
Headset status
The headset is connected to a Bluetooth device, while the headset in standby mode or while you are listening to music.
The headset is ready for pairing.
The headset is on but not connected to a Bluetooth device.
There is an incoming call.
Indicator
Blue LED flashes for every 8 seconds.
LED flashes blue and white alternately.
Blue LED flashes quickly.
Low battery.
Battery is fully charged.
Blue LED flashes once per second.
White LED flashes.
White LED is off.
Tip
Wear your headset
Adjust the headband for the best fit.
•
After use, twist both earshells, fold the headset flat for storage.
Use with the audio cable
Note
•
Make sure that you turn off the Bluetooth headset before connecting the audio cable.
With the supplied audio cable, you can use the headset with non-Bluetooth devices or on airplane. No battery power is required for the headset when you use it with the audio cable.
Connect the supplied audio cable to
• the headset and;
• an external audio device.
EN
7
5 Technical data
• Up to 9 hours of music time or talk time
• Up to 200 hours of standby time
• Normal time for a full charge: 3 hours
• Rechargeable Lithium-Polymer battery
(230 mAh)
• 3.5 mm audio jack for corded headset mode
• Bluetooth 2.1 EDR, Bluetooth mono support (Headset Profile - HSP, Hands-
Free Profile - HFP), Bluetooth stereo supported (Advanced Audio Distribution
Profile - A2DP; Audio Video Remote
Control Profile - AVRCP)
• Operating range: Up to 15 meters (50 feet)
• Digital echo & noise reduction
• Auto power off
Note
•
Specifications are subject to change without notice.
8
EN
6 Notice
Declaration of conformity
Hereby, WOOX Innovations declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. You can find the
Declaration of Conformity on www.p4c.philips.
com.
This product has been designed, tested and manufactured according the European R&TTE directive 1999/5/EC.
Disposal of your old product and batteries
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/
EC. Please inform yourself about the local separate collection system for electrical and electronic products.
Please act according to your local rules and do not dispose of your old products with your normal household waste.
Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be disposed with normal household waste.
Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.
Remove the integrated battery
Note
•
Make sure the headset is disconnected from the USB charging cable before removing the battery.
If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headset.
1 2 3 4
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
EN
9
Notice for the European
Union
0168
Hereby, WOOX Innovations declares that this product is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Trademarks
2013 © WOOX Innovations Limited. All rights reserved.
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited under license from Koninklijke Philips N.V.
Bluetooth
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by WOOX Innovations Limited is under license.
10 EN
7 Frequently asked questions
My Bluetooth headset does not switch on.
The battery level is low. Charge the headset.
I cannot pair my Bluetooth headset with a mobile phone.
The Bluetooth is disabled. Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headset.
Pairing does not work.
Make sure the headset is in pairing mode.
• Make sure that the LED light flashes blue and white alternately before you release the call/music button. Do not stop holding the button if you see the blue LED only.
The mobile phone cannot find the headset.
• The headset may be connected to a previously paired device. Turn off the connected device or move it out of range.
• Pairing may have been reset or the headset has been previously paired with another device. Pair the headset with the mobile
Voice dialing or redialing does not work on my mobile phone.
Your mobile phone may not support this feature.
The other side cannot hear me on the mobile phone.
The microphone is muted. Press volume/track control button once to enable the microphone.
My Bluetooth headset is connected to a
Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone.
Select to listen to music through the headset.
The audio quality is poor and crackling noise can be heard.
The Bluetooth device is out of range. Reduce the distance between your headset and
Bluetooth device, or remove obstacles between them.
The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.
Make sure your mobile phone not only supports (mono) HSP/HFP but also supports
A2DP.
I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip forward/ backward).
Make sure the Bluetooth audio source supports
AVRCP.
My headset does not work when the audio cable is connected.
Microphone function will be deactivated if a
3.5mm audio cable is connected to the headset.
In such case, your headset is only for music enjoyment.
How can I restore all original headset settings?
Press volume/track control button and call music button until the LED flashing white for 5 times sequentially.
For further support, visit www.philips.com/ support.
EN
11
2013 © WOOX Innovations Limited.
All rights reserved.
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited under license from
Koninklijke Philips N.V.
SHB9150_UM_V1.0
wk1429
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- On-ear
- Black
Related manuals
advertisement
Table of contents
- 4 Hearing Safety
- 4 General information
- 4 Compliance with EMF
- 5 What's in the box
- 5 Other devices
- 5 Overview of your Bluetooth stereo headset
- 6 Charge your headset
- 6 Pair the headset with your mobile phone
- 6 Manual pairing
- 6 NFC pairing
- 8 Connect the headset to a Bluetooth device
- 8 Automatic power saving
- 8 Manage your calls and music
- 9 Wear your headset
- 9 Use with the audio cable
- 11 Declaration of conformity
- 11 Disposal of your old product and batteries
- 11 Remove the integrated battery
- 11 Notice for the European Union
- 12 Trademarks
- 12 Bluetooth