Ford Focus car Owner's Manual

FORD FOCUS Owner's Manual
The information contained in this publication was correct at the time of going to print. In the interest of
continuous development, we reserve the right to change specifications, design or equipment at any time
without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a
retrieval system or translated into any language in any form by any means without our written permission.
Errors and omissions excepted.
© Ford Motor Company 2011
All rights reserved.
Part Number: (CG3568en) 08/2011 20110622085519
Table of Contents
Introduction
Alarm
About This Manual...........................................7
Symbols Glossary.............................................7
Parts and Accessories.....................................7
Principle of Operation..................................39
Arming the alarm...........................................40
Disarming the alarm.....................................40
At a Glance
Steering Wheel
At a Glance........................................................10
Adjusting the Steering Wheel.....................41
Audio Control....................................................41
Voice Control...................................................42
Child Safety
Child Seats.........................................................17
Child Seat Positioning...................................18
Booster Seats..................................................20
ISOFIX Anchor Points....................................21
Child Safety Locks..........................................22
Wipers and Washers
Windscreen Wipers.......................................43
Autowipers.......................................................43
Windscreen Washers....................................44
Rear Window Wiper and Washers...........44
Headlamp Washers......................................45
Checking the Wiper Blades........................45
Changing the Wiper Blades.......................45
Occupant protection
Principle of Operation..................................24
Fastening the seat belts..............................25
Seat belt height adjustment......................26
Seat belt reminder.........................................26
Using seat belts during pregnancy...........27
Disabling the passenger airbag.................27
Lighting
Lighting Control...............................................47
Autolamps........................................................48
Automatic Main Beam Control.................48
Front Fog Lamps............................................50
Rear Fog Lamps.............................................50
Adjusting the Headlamps - Vehicles
With: Adaptive Front Lighting/Xenon
Headlamps....................................................51
Headlamp Levelling.......................................51
Hazard Warning Flashers.............................51
Direction Indicators........................................52
Cornering Lamps............................................52
Interior Lamps.................................................53
Removing a Headlamp................................54
Changing a Bulb.............................................55
Bulb Specification Chart.............................62
Keys and Remote Controls
General Information on Radio
Frequencies..................................................29
Programming the remote control............29
Changing the remote control
battery............................................................29
Locks
Locking and Unlocking.................................32
Keyless Entry....................................................34
Global Opening and Closing......................36
Engine immobiliser
Principle of Operation..................................38
Coded keys.......................................................38
Arming the engine immobiliser................38
Disarming the engine immobiliser...........38
Windows and Mirrors
Power Windows..............................................63
1
Table of Contents
Exterior Mirrors................................................64
Electric exterior mirrors................................65
Auto-Dimming Mirror...................................66
Blind Spot Monitor........................................66
Instrument Cluster
Glasses Holder................................................112
Childminder Mirror.........................................112
Auxiliary input (AUX IN) socket................113
USB port............................................................113
Satellite Navigation Unit Holder..............113
Floor Mats.........................................................113
Gauges...............................................................69
Warning Lamps and Indicators..................71
Audible Warnings and Indicators..............73
Starting and Stopping the
Engine
General Information.....................................114
Ignition Switch................................................114
Steering Wheel Lock....................................114
Starting a Petrol Engine..............................115
Starting a Petrol Engine - E85..................115
Starting a Diesel Engine..............................116
Keyless Starting.............................................116
Diesel Particulate Filter...............................118
Switching Off the Engine............................119
Engine Block Heater.....................................119
Information Displays
General Information......................................75
Trip Computer.................................................82
Personalised Settings..................................82
Information Messages.................................83
Climate Control
Principle of Operation..................................94
Air Vents............................................................94
Manual Climate Control..............................95
Automatic Climate Control........................97
Heated Windows and Mirrors.................100
Electric sunroof.............................................100
Auxiliary Heater.............................................102
Start-Stop
Principle of Operation.................................120
Using start-stop............................................120
Eco Mode
Seats
Principle of Operation.................................122
Using Eco mode............................................122
Sitting in the Correct Position..................105
Manual Seats.................................................105
Head Restraints............................................106
Power Seats...................................................108
Rear Seats.......................................................109
Heated Seats..................................................110
Fuel and Refuelling
Safety Precautions.......................................123
Fuel Quality - Petrol.....................................123
Fuel Quality - E85.........................................123
Fuel Quality - Diesel.....................................123
Catalytic Converter......................................124
Fuel filler flap.................................................124
Refuelling.........................................................126
Refuelling - E85.............................................126
Fuel Consumption........................................127
Technical Specifications............................127
Convenience features
Instrument Lighting Dimmer......................111
Clock....................................................................111
Cigar Lighter......................................................111
Auxiliary Power Points..................................111
Cup Holders.....................................................112
2
Table of Contents
Using Adaptive Cruise Control................150
Forward alert function................................152
Transmission
Manual Transmission..................................129
Automatic Transmission............................129
Speed Limiter
Principle of Operation.................................153
Using the speed limiter...............................153
Brakes
Principle of Operation.................................132
Hints on Driving With Anti-Lock
Brakes...........................................................132
Parking Brake..................................................132
Driver Alert
Principle of Operation.................................154
Using driver alert...........................................154
Stability Control
Lane Departure Warning
Principle of Operation.................................133
Using Stability Control................................133
Principle of Operation.................................156
Using lane departure warning.................156
Hill Start Assist
Lane Keeping Aid
Principle of Operation.................................134
Using hill start assist...................................134
Principle of Operation.................................158
Using the lane keeping aid........................158
Parking Aids
Principle of Operation.................................136
Using the Parking Aid - Vehicles With:
Rear Parking Aid.......................................136
Using the Parking Aid - Vehicles With:
Front and Rear Parking Aid...................137
Traffic Sign Recognition
Rear view camera
Principle of Operation.................................162
Using Active City Stop................................162
Principle of Operation................................160
Using traffic sign recognition...................160
Active City Stop
Principle of Operation................................140
Using the Rear View Camera...................140
Load Carrying
General Information....................................164
Luggage Anchor Points..............................164
Luggage Covers.............................................164
Cargo Nets......................................................165
Dog Guard.......................................................166
Roof Racks and Load Carriers.................168
Active Park Assist
Principle of Operation.................................143
Using active park assist..............................143
Cruise Control
Principle of Operation................................146
Using Cruise Control...................................146
Towing
Towing a Trailer.............................................170
Retractable tow ball....................................170
Tow Ball............................................................173
Adaptive cruise control
(ACC)
Principle of Operation................................148
3
Table of Contents
Brake and Clutch Fluid Check................200
Washer Fluid Check...................................200
Technical Specifications............................201
Driving Hints
Running-In.......................................................176
Cold Weather Precautions........................176
Driving Through Water................................176
Vehicle Care
First Aid Kit.......................................................177
Warning Triangle............................................177
Cleaning the Exterior..................................204
Cleaning the Interior...................................204
Repairing Minor Paint Damage..............205
Fuses
Vehicle battery
Fuse Box Locations......................................178
Changing a Fuse............................................179
Fuse Specification Chart...........................180
Jump-Starting the Vehicle.......................206
Changing the Vehicle Battery.................207
Battery connection points........................207
Vehicle recovery
Wheels and Tyres
Towing Points................................................188
Towing the Vehicle on Four Wheels......188
General Information...................................208
Changing a Road Wheel...........................208
Tyre Repair Kit................................................213
Tyre Care..........................................................216
Using Winter Tyres........................................217
Using Snow Chains.......................................217
Tyre Pressure Monitoring System...........217
Technical Specifications............................218
Roadside Emergencies
Maintenance
General Information....................................190
Opening and Closing the Bonnet...........190
Under Bonnet Overview - 1.6L
Duratec-16V Ti-VCT (Sigma)..............192
Under Bonnet Overview - 1.6L EcoBoost
SCTi (Sigma).............................................193
Under Bonnet Overview - 1.6L
Duratorq-TDCi (DV) Diesel..................194
Under Bonnet Overview - 2.0L
Duratec-HE (MI4)....................................195
Under Bonnet Overview - 2.0L
Duratorq-TDCi (DW) Diesel.................197
Engine Oil Dipstick - 1.6L Duratec-16V
Ti-VCT (Sigma)........................................198
Engine Oil Dipstick - 1.6L EcoBoost SCTi
(Sigma).......................................................198
Engine Oil Dipstick - 2.0L Duratec-HE
(MI4).............................................................198
Engine Oil Dipstick - 1.6L Duratorq-TDCi
(DV) Diesel/2.0L Duratorq-TDCi (DW)
Diesel............................................................198
Engine Oil Check..........................................198
Engine Coolant Check................................199
Vehicle identification
Vehicle Identification Plate.......................221
Vehicle Identification Number................222
Capacities and Specifications
Technical Specifications...........................223
Audio introduction
Important audio information...................227
Audio unit overview
Audio unit overview....................................228
4
Table of Contents
Bluetooth setup...........................................245
Telephone setup..........................................245
Telephone controls.....................................246
Using the telephone...................................246
Audio system security
Security code.................................................234
Audio unit operation
On/off control...............................................235
Sound button................................................235
Waveband button........................................235
Station tuning control................................235
Station preset buttons..............................236
Autostore control.........................................236
Traffic information control.......................236
Voice control
Principle of Operation................................249
Using voice control.....................................249
Audio unit commands...............................250
Telephone commands...............................257
Climate control commands....................262
Audio unit menus
Connectivity
Automatic volume control.......................238
Digital signal processing (DSP).............238
News broadcasts.........................................238
Alternative frequencies.............................238
Regional mode (REG)................................239
General Information...................................265
Connecting an external device...............266
Connecting an external device - Vehicles
With: Bluetooth........................................266
Using a USB device.....................................267
Using an iPod................................................268
Compact disc player
Navigation introduction
Compact disc playback............................240
Track selection.............................................240
Fast forward/reverse..................................240
Shuffle/random...........................................240
Repeat compact disc tracks...................240
Compact disc track scanning..................241
MP3 file playback.........................................241
MP3 display options....................................241
Ending compact disc playback..............242
General Information...................................270
Road Safety...................................................270
Navigation unit overview
Navigation unit overview...........................272
Loading the navigation data....................276
Navigation Quick start
Navigation Quick start................................277
Auxiliary input (AUX IN)
socket
System settings
System settings...........................................280
Auxiliary input (AUX IN) socket.............243
Navigation system
Audio troubleshooting
Route options menu...................................283
Route displays..............................................284
Audio troubleshooting...............................244
Telephone
Traffic Message Channel
General Information...................................245
Principle of Operation................................285
5
Table of Contents
Using TMC......................................................285
Map updates
Map updates.................................................286
Appendices
Type approvals.............................................287
Type approvals.............................................287
Type approvals.............................................287
Type approvals.............................................288
Type approvals.............................................288
Type approvals.............................................289
Electromagnetic compatibility..............289
6
Introduction
ABOUT THIS MANUAL
CAUTION
You risk damaging your vehicle if you
do not follow the instructions
highlighted by the caution symbol.
Thank you for choosing Ford. We
recommend that you take some time to
get to know your vehicle by reading this
manual. The more that you know about it,
the greater the safety and pleasure you
will get from driving it.
Symbols on your vehicle
WARNING
Always drive with due care and
attention when using and operating
the controls and features on your
vehicle.
When you see these symbols, read and
follow the relevant instructions in this
handbook before touching or attempting
adjustment of any kind.
Note: This manual describes product
features and options available throughout
the range, sometimes even before they are
generally available. It may describe options
not fitted to your vehicle.
PARTS AND ACCESSORIES
Note: Some of the illustrations in this
manual may be used for different models,
so may appear different to your vehicle.
However, the essential information in the
illustrations is always correct.
Now you can be sure that your Ford
parts are Ford parts
Your Ford has been built to the highest
standards using high quality Ford Original
Parts. As a result, you can enjoy driving it
for many years.
Note: Always use and operate your vehicle
in line with all applicable laws and
regulations.
Should the unexpected occur and a major
part needs replacing, we recommend that
you accept nothing less than Ford Original
Parts.
Note: Pass on this manual when selling
your vehicle. It is an integral part of the
vehicle.
The use of Ford Original Parts ensures that
your vehicle is repaired to its pre-accident
condition and maintains its maximum
residual value.
SYMBOLS GLOSSARY
Symbols in this handbook
Ford Original Parts match Ford's stringent
safety requirements and high standards
of fit, finish and reliability. Quite simply,
they represent the best overall repair value,
including parts and labour costs.
WARNING
You risk death or serious injury to
yourself and others if you do not
follow the instructions highlighted
by the warning symbol.
7
Introduction
Now it is easier to tell if you have really
been given Ford Original Parts. The Ford
logo is clearly visible on the following parts
if they are Ford Original Parts. If your
vehicle has to be repaired, look for the
clearly visible Ford branding and make sure
that only Ford Original Parts have been
used.
Look for the Ford logo on the
following parts
Sheet metal
•
•
•
Bonnet
Doors
Luggage compartment lid or tailgate
E132326
Exterior mirror
E132340
Glass
E132325
•
•
•
Bumper and radiator grille
•
•
Radiator grille
Front and rear bumper
8
Rear window
Side glass
Windscreen
Introduction
E132327
Lighting
•
•
Rear lamps
Headlamp
E132328
9
At a Glance
Front exterior overview
A
B
C
D
H
F
G
E
E133220
A
See Locking and Unlocking (page 32). See Keyless Entry (page 34).
B
See Automatic Main Beam Control (page 48). See Driver Alert (page 154).
See Lane Departure Warning (page 156). See Lane Keeping Aid (page 158).
See Traffic Sign Recognition (page 160). See Active City Stop (page 162).
C
See Changing the Wiper Blades (page 45).
D
See Maintenance (page 190).
E
See Towing Points (page 188).
10
At a Glance
F
See Changing a Bulb (page 55).
G
Tyre pressures. See Technical Specifications (page 218).
H
See Changing a Road Wheel (page 208).
Vehicle interior overview
A
B
C
D
E
I
H
E133222
G
F
A
See Transmission (page 129).
B
See Locking and Unlocking (page 32).
C
See Power Windows (page 63). See Electric exterior mirrors (page 65).
11
At a Glance
D
See Head Restraints (page 106).
E
See Fastening the seat belts (page 25).
F
See Rear Seats (page 109).
G
See Manual Seats (page 105). See Power Seats (page 108).
H
See Parking Brake (page 132).
I
See Opening and Closing the Bonnet (page 190).
Instrument panel overview
Left-hand drive
A B
W
E132738
C
V
D
U
T
E
S
F
R
Q
12
P
G
O N M
H
I
L
K
J
At a Glance
Right-hand drive
I
H
M
L
B
C
S
A
Air vents. See Air Vents (page 94).
B
Direction indicators. See Direction Indicators (page 52). Main beam. See
Lighting Control (page 47).
C
Left-hand drive vehicles with voice control - Information display control. See
Information Displays (page 75).
C
Left-hand drive vehicles without voice control - Information display control.
See Information Displays (page 75).
C
Right-hand drive vehicles with voice control - Information and entertainment
display control.
C
Right-hand drive vehicles without voice control - Information display control.
See Information Displays (page 75).
13
T
F
A
P Q
U
E
O
K
V
D
J
E132739
N
G
R
W
At a Glance
D
Instrument cluster. See Gauges (page 69). See Warning Lamps and
Indicators (page 71).
E
Left-hand drive vehicles with voice control - Information and entertainment
display control.
E
Left-hand drive vehicles without voice control - Audio control. See Audio
Control (page 41).
E
Right-hand drive vehicles with voice control - Information display control. See
Information Displays (page 75).
E
Right-hand drive vehicles without voice control - Audio control. See Audio
Control (page 41).
F
Wiper lever. See Wipers and Washers (page 43).
G
Information and entertainment display.
H
Audio unit. See Audio unit overview (page 228).
I
Door lock button. See Locking and Unlocking (page 32).
J
Hazard warning flasher switch. See Hazard Warning Flashers (page 51).
K
Parking aid switch. See Parking Aids (page 136).
L
Active park assist switch. See Active Park Assist (page 143).
M
Start-stop switch. See Using start-stop (page 120).
N
Heated rear window switch. See Heated Windows and Mirrors (page 100).
O
Heated windscreen switch. See Heated Windows and Mirrors (page 100).
P
Climate controls. See Climate Control (page 94).
Q
Start button. See Keyless Starting (page 116).
R
Ignition switch. See Ignition Switch (page 114).
S
Audio control. See Audio Control (page 41). Voice control. See Voice Control
(page 42). Telephone control. See Telephone controls (page 246).
T
Steering wheel adjustment. See Adjusting the Steering Wheel (page 41).
U
Horn.
V
Cruise control switches. See Using Cruise Control (page 146). Adaptive cruise
control (ACC) switches. See Using Adaptive Cruise Control (page 150).
Speed limiter switches. See Using the speed limiter (page 153).
W
Lighting control. See Lighting Control (page 47). Front fog lamps. See Front
Fog Lamps (page 50). Rear fog lamp. See Rear Fog Lamps (page 50).
Headlamp levelling control. See Headlamp Levelling (page 51). Instrument
lighting dimmer. See Instrument Lighting Dimmer (page 111).
14
At a Glance
Rear exterior overview
A
B
C
D
E133221
G
H
A
See Changing the Wiper Blades (page 45).
B
See Changing a Bulb (page 55).
C
See Changing a Bulb (page 55).
D
See Fuel filler flap (page 124).
E
See Changing a Road Wheel (page 208).
F
Tyre pressures. See Technical Specifications (page 218).
15
F
E
At a Glance
G
See Towing Points (page 188).
H
See First Aid Kit (page 177). See Warning Triangle (page 177). See Tyre
Repair Kit (page 213). Spare wheel. See Changing a Road Wheel (page 208).
Jack. See Changing a Road Wheel (page 208). Wheel brace. See Changing
a Road Wheel (page 208). Towing eye. See Towing Points (page 188). Fuel
funnel. See Fuel filler flap (page 124).
16
Child Safety
CHILD SEATS
WARNINGS
Do not leave unattended children in
your vehicle.
If your vehicle has been involved in
an accident, have the child restraints
checked by properly trained
technicians.
Note: Mandatory use of child restraints
varies from country to country.
E133140
Only child restraints certified to
ECE-R44.03 (or later) have been tested
and approved for use in your vehicle. A
choice of these are available from your
Dealer.
Child restraints for different mass
groups
Use the correct child restraint as follows:
Baby safety seat
E68916
WARNINGS
Secure children that are less than
150 centimetres (59 inches) tall in a
suitable, approved child restraint, in
the rear seat.
Extreme Hazard! Do not use a
rearward facing child restraint on a
seat protected by an air bag in front
of it!
Read and follow the manufacturer’s
instructions when you are fitting a
child restraint.
E68918
Secure children that weigh less than 13
kilograms (29 pounds) in a rearward facing
baby safety seat (Group 0+) in the rear
seat.
Do not modify child restraints in any
way.
Do not hold a child on your lap when
the vehicle is moving.
17
Child Safety
Child safety seat
WARNINGS
Extreme Hazard! Do not use a
rearward facing child restraint on a
seat protected by an air bag in front
of it!
When using a child seat with a
support leg, the support leg must
rest securely on the floor.
When using a child seat with a seat
belt, make sure that the seat belt is
not slack or twisted.
CAUTION
The child seat must rest tightly
against the vehicle seat. It may be
necessary to lift or remove the head
restraint. See Head Restraints (page 106).
E68920
Secure children that weigh between 13 and
18 kilograms (29 and 40 pounds) in a child
safety seat (Group 1) in the rear seat.
Note: When using a child seat on a front
seat, always adjust the front passenger seat
to its fully rearwards position. If it proves
difficult to tighten the lap section of the seat
belt without slack remaining, adjust the
seatback to the fully upright position and
raise the height of the seat. See Seats
(page 105).
CHILD SEAT POSITIONING
WARNINGS
Please consult your Dealer for the
latest details relating to Ford
recommended child seats.
Mass group categories
0
0+
Seating positions
Up to 10 kg Up to 13 kg
(22 lbs)
(29 lbs)
1
2
3
9 - 18 kg
(20 - 40
lbs)
15 - 25 kg
(33 - 55
lbs)
22 - 36 kg
(49 - 79
lbs)
Front passenger seat
with airbag ON
X
X
UF¹
UF¹
UF¹
Front passenger seat
with airbag OFF
U
U
U
U
U
Rear seats
U
U
U
U
U
X Not suitable for children in this mass group.
U Suitable for universal category child seats approved for use in this mass group.
18
Child Safety
UF¹ Suitable for universal category forward facing child restraints approved for use in
this mass group. However, we recommend that you secure children in a government
approved child restraint, in the rear seat.
ISOFIX child seats
Mass group categories
0+
1
Seating positions
Front seat
Size class
Rear centre seat
Forward facing
9 - 18 kg (20 - 40 lbs)
Not ISOFIX equipped
Seat type
Rear outboard seat ISOFIX
Rear facing
Up to 13 kg (29 lbs)
Size class
C, D, E
Seat type
IL
2
Size class
1
A, B, B1, C, D
1
3
IL, IUF
Not ISOFIX equipped
Seat type
IL Suitable for particular ISOFIX child restraints systems of the semi-universal category.
Please consult child restraints systems suppliers' vehicle recommendation lists.
IUF Suitable for ISOFIX forward facing child restraints systems of universal category
approved for use in this mass group and ISOFIX size class.
1
The ISOFIX size class for both universal and semi-universal child restraints systems
is defined by the capital letters A to G. These identification letters are displayed on ISOFIX
child restraints.
2
At time of publishing the recommended Group O+ ISOFIX baby safety seat is the Britax
Roemer Baby Safe. Please consult your Dealer for the latest details relating to Ford
recommended child seats.
3
At time of publishing the recommended Group 1 ISOFIX child seat is the Britax Roemer
Duo. Please consult your Dealer for the latest details relating to Ford recommended child
seats.
19
Child Safety
Booster seat (Group 2)
BOOSTER SEATS
WARNINGS
Do not install a booster seat or a
booster cushion with only the lap
strap of the seat belt.
Do not install a booster seat or a
booster cushion with a seat belt that
is slack or twisted.
Do not put the seat belt under your
child’s arm or behind its back.
Do not use pillows, books or towels
to boost your child’s height.
Make sure that your children sit in an
upright position.
E70710
We recommend that you use a booster
seat that combines a cushion with a
backrest instead of a booster cushion only.
The raised seating position will allow you
to position the shoulder strap of the adult
seat belt over the centre of your child’s
shoulder and the lap strap tightly across
its hips.
Secure children that weigh more
than 15 kilograms (33 pounds) but
are less than 150 centimetres (59
inches) tall in a booster seat or a booster
cushion.
CAUTION
Booster cushion (Group 3)
When using a child seat on a rear seat,
make sure that the child seat rests
tightly against the vehicle seat. It may
be necessary to lift or remove the head
restraint. See Head Restraints (page 106).
E68924
20
Child Safety
Top tether anchor points - 4 door
vehicles
ISOFIX ANCHOR POINTS
WARNING
Use an anti-rotation device when
using the ISOFIX system. We
recommend the use of a top tether
or support leg.
Note: When you are purchasing an ISOFIX
restraint, make sure that you know the
correct mass group and ISOFIX size class
for the intended seating locations. See
Child Seat Positioning (page 18).
Your vehicle is fitted with ISOFIX anchor
points that accommodate universally
approved ISOFIX child restraints.
E132903
The ISOFIX system comprises of two rigid
attachment arms on the child restraint that
attach to anchor points on the rear seats,
where the cushion and backrest meet.
Tether anchor points may also be fitted.
The tether anchor points are located under
a flap.
Attaching a child seat with top
tethers
Top tether anchor points - all
vehicles
WARNING
Do not attach a tether strap to
anything other than the correct
tether anchor point.
Note: Where applicable, remove the
luggage cover to ease installation. See
Luggage Covers (page 164).
WARNING
Make sure that the top tether strap
is not slack or twisted and is properly
located on the anchor point.
1.
E132902
21
Route the tether strap to the anchor
point.
Child Safety
E87145
2. Push the child seat back firmly to
engage the ISOFIX lower anchor points.
3. Tighten the tether strap in line with the
child seat manufacturer's instructions.
E78298
Left-hand side
Turn anti-clockwise to lock and clockwise
to unlock.
CHILD SAFETY LOCKS
Right-hand side
WARNING
Turn clockwise to lock and anti-clockwise
to unlock.
You cannot open the doors from
inside if you have put the child safety
locks on.
Electric child safety locks
Manual child safety locks
Note: Pressing the switch will also disable
the rear electric window switches.
Note: On vehicles with keyless entry, use
the spare key. See Keyless Entry (page
34).
22
Child Safety
E124779
23
Occupant protection
Front airbags
PRINCIPLE OF OPERATION
Airbags
WARNINGS
Do not modify the front of your
vehicle in any way. This could
adversely affect deployment of the
airbags.
Extreme Hazard! Do not use a
rearward facing child restraint on a
seat protected by an airbag in front
of it!
E74302
Wear a seat belt and keep sufficient
distance between yourself and the
steering wheel. Only when you use
the seat belt properly, can it hold you in a
position that allows the airbag to achieve
its optimum effect. See Sitting in the
Correct Position (page 105).
The driver airbag, front passenger airbag
and the front seat belt pretensioners will
deploy during significant frontal collisions
or collisions that are up to 30 degrees from
the left or the right. The airbags will inflate
within a few thousandths of a second and
deflate on contact with the occupants,
thus cushioning forward body movement.
During minor frontal collisions, overturns,
rear collisions and side collisions, the driver
and front passenger airbags will not
deploy.
Have repairs to the steering wheel,
steering column, seats, airbags and
seat belts carried out by a properly
trained technician.
Keep the areas in front of the airbags
free from obstruction. Do not affix
anything to or over the airbag covers.
Side and curtain airbags
Do not poke sharp objects into areas
where airbags are fitted. This could
damage and adversely affect
deployment of the airbags.
During significant lateral collisions, only
the airbags on the side affected by the
collision and the front seat belt
pretensioners will deploy. The airbags will
inflate within a few thousandths of a
second and deflate on contact with the
occupants, thus providing protection for
the body. The side and curtain airbags will
not deploy during minor lateral collisions,
front collisions, rear collisions or overturns.
Use seat covers designed for seats
with side airbags. Have these fitted
by a properly trained technician.
Note: You will hear a loud bang and see a
cloud of harmless powdery residue if an
airbag deploys. This is normal.
Note: Only wipe airbag covers with a damp
cloth.
24
Occupant protection
Side airbags
WARNINGS
Never use a seat belt for more than
one person.
Use the correct buckle for each seat
belt.
Do not use a seat belt that is slack
or twisted.
Do not wear thick clothing. The seat
belt must fit tightly around your body
to achieve its optimum effect.
E72658
Position the shoulder strap of the
seat belt over the centre of your
shoulder and position the lap strap
tightly across your hips.
Side airbags are fitted inside the seatback
of the front seats. A label indicates that
side airbags are fitted to your vehicle.
Curtain airbags
The driver and front passenger seat belt
systems are fitted with a seat belt
pretensioner. Seat belt pretensioners have
a lower deployment threshold than the
airbags. During minor collisions, it is
possible that only the seat belt
pretensioners will deploy.
Status after a collision
WARNINGS
Seat belts subjected to strain, as a
result of an accident, should be
renewed and the anchorages
checked by a properly trained technician.
E75004
Curtain airbags are fitted inside the trim
panels over the front and rear side
windows. Moulded badges in the B-pillar
trim panels indicate that curtain airbags
are fitted to your vehicle.
If a seat belt pretensioner has been
deployed the seat belt must be
renewed.
FASTENING THE SEAT BELTS
Seat belts
WARNINGS
Wear a seat belt and keep sufficient
distance between yourself and the
steering wheel. Only when you use
the seat belt properly, can it hold you in a
position to achieve its optimum effect. See
Sitting in the Correct Position (page
105).
WARNING
Insert the tongue into the buckle until
you hear a distinct click. You have
not fastened the seat belt properly
if you do not hear a click.
25
Occupant protection
SEAT BELT HEIGHT
ADJUSTMENT
E74124
E87511
Note: Lifting the slider slightly while
pressing the locking button makes it easier
to release the locking mechanism.
To raise or lower, press the locking button
on the adjuster and move as necessary.
SEAT BELT REMINDER
WARNING
The occupant protection system will
only provide optimum protection
when you use the seat belt properly.
E85817
Pull the belt out steadily. It may lock if you
pull it sharply or if the vehicle is on a slope.
Press the red button on the buckle to
release the belt. Let it retract completely
and smoothly.
The seat belt reminder warning
lamp illuminates and an audible
warning will sound if the driver's
or front seat passenger's seat belt has not
been fastened and the vehicle exceeds a
relatively low speed. It will also illuminate
if the driver's or front seat passenger's seat
belt is unfastened when the vehicle is
moving. The audible warning will go off
after a few minutes but the seat belt
reminder warning lamp will remain on until
the driver's or front seat passenger's seat
belt is fastened.
26
Occupant protection
Rear seat belt reminder
WARNING
Position the seat belt correctly for
your safety and that of your unborn
child. Do not use only the lap strap
or the shoulder strap.
WARNING
If multiple belts are unfastened
within a few seconds of each other,
only one audible chime will sound.
Position the lap strap comfortably across
your hips and low beneath your pregnant
abdomen. Position the shoulder strap
between your breasts, above and to the
side of your pregnant abdomen.
Note: Press the OK button on the steering
wheel control to confirm the message.
A visual reminder of the seat belt status
will be shown on the instrument display
once the engine is started, and once again
if any are unfastened when the vehicle is
moving.
DISABLING THE PASSENGER
AIRBAG
Fastened seat belts are indicated by a tick
symbol.
WARNING
If a belt is unfastened when the vehicle is
moving, the seat belt status screen will be
displayed and the relevant seats will be
highlighted by an exclamation mark. An
audible chime will also sound.
Make sure that the passenger airbag
is disabled when using a rearward
facing child restraint on the front
passenger seat.
Deactivating the seat belt
reminder
See your dealer.
USING SEAT BELTS DURING
PREGNANCY
E71313
Fitting the passenger airbag
deactivation switch
WARNING
If you need to fit a child restraint on
a seat protected by an operational
airbag in front of it, have a passenger
airbag deactivation switch fitted. Ask your
dealer for further information.
E68587
27
Occupant protection
Note: The key switch is located in the glove
compartment with an airbag deactivation
lamp in the overhead console.
If the airbag warning lamp illuminates or
flashes when you are driving, this indicates
a malfunction. See Warning Lamps and
Indicators (page 71). Remove the child
restraint and have the system checked
immediately.
Disabling the passenger airbag
A
B
E71312
A
Disabled
B
Enabled
Turn the switch to position A.
When you switch the ignition on, check that
the passenger airbag deactivation warning
lamp illuminates.
Enabling the passenger airbag
WARNING
Make sure that the passenger airbag
is enabled when you are not using a
child restraint on the front passenger
seat.
Turn the switch to position B.
28
Keys and Remote Controls
Note: Further remote controls may be
programmed at this stage.
GENERAL INFORMATION ON
RADIO FREQUENCIES
4. Press any button on each additional
remote control within 10 seconds of
each other.
CAUTIONS
The radio frequency used by your
remote control can also be used by
other short distance radio
transmissions (e.g. amateur radios,
medical equipment, wireless headphones,
remote controls and alarm systems). If the
frequencies are jammed, you will not be
able to use your remote control. You can
lock and unlock the doors with the key.
Reprogramming the unlocking
function
Note: When you press the unlock button
either all the doors are unlocked or only the
driver’s door is unlocked. Pressing the unlock
button again unlocks all the doors.
Press and hold the unlock and lock buttons
on the remote key simultaneously for at
least four seconds with the ignition off. The
direction indicators will flash twice to
confirm the change.
Check your vehicle is locked before
leaving it unattended. This will
safeguard against any potential
malicious frequency blocking.
To return to the original unlocking function,
repeat the process.
Note: You could unlock the doors if you
press the buttons on the remote control
unintentionally.
CHANGING THE REMOTE
CONTROL BATTERY
The operating range between your remote
control and your vehicle varies depending
on the environment.
Make sure that you dispose of
old batteries in an
E107998
environmentally friendly way.
Seek advice from your local authority
regarding recycling.
PROGRAMMING THE REMOTE
CONTROL
You can programme a maximum of eight
remote controls to use with your vehicle
(including any supplied with your vehicle).
Remote control with a folding key
blade
Programming a new remote
control
1. Insert the key in the ignition.
2. Cycle the key from position 0 to II and
then back to 0 four times within six
seconds.
3. Leave the key in position 0 and press
any button on the remote control
within 10 seconds. You will receive
confirmation via a chime or LED that
programming has been successful.
1
2
E128809
29
Keys and Remote Controls
Remote control without a folding
key blade
1.
Insert a screwdriver in the position
shown and gently push the clip.
2. Press the clip down to release the
battery cover.
2
1
E128810
1
E87964
3. Carefully remove the cover.
1.
Press and hold the pushbuttons on the
edges to release the cover. Carefully
remove the cover.
2. Remove the key blade.
3
E128811
4. Turn the remote control over to remove
the battery.
5. Install a new battery (3V CR 2032) with
the + facing upwards.
6. Replace the battery cover.
E105362
3. Twist a flat bladed screwdriver in the
position shown to separate the two
halves of the remote control.
30
Keys and Remote Controls
4
E119190
4. Carefully insert the screwdriver in the
position shown to open the remote
control.
5
E125860
CAUTION
Do not touch the battery contacts or
the printed circuit board with the
screwdriver.
5. Carefully prise out the battery with the
screwdriver.
6. Install a new battery (3V CR 2032) with
the + facing downwards.
7. Assemble the two halves of the remote
control.
8. Install the key blade.
31
Locks
Double locking with the key
LOCKING AND UNLOCKING
Turn the key to the lock position twice
within three seconds.
CAUTION
Check your vehicle is locked before
leaving it unattended.
Double locking with the remote control
Press the button twice within
three seconds.
Note: Do not leave your keys in the vehicle.
Locking
Unlocking
Locking with the key
Unlocking with the key
Turn the top of the key towards the front
of the vehicle.
Turn the top of the key towards the rear of
the vehicle.
Locking with the remote control
Unlocking with the remote control
Note: The driver’s door can be locked with
the key. This needs to be used if the remote
control is not functioning.
Note: The driver’s door can be unlocked
with the key. This needs to be used if the
remote control is not functioning.
Note: Your vehicle can be locked with a rear
door open. The door will be locked when it
is closed.
Note: If the vehicle remains locked for
several weeks, the remote control will be
disabled. The vehicle must be unlocked and
the engine started using the key. Unlocking
and starting the vehicle once will enable the
remote control.
Press the button.
Press the button.
Double locking
WARNING
Do not activate double locking when
persons or animals are inside the
vehicle. You will not be able to
unlock the doors from the inside if you have
double locked them.
Automatic relocking
The doors will relock automatically if you
do not open a door, the luggage
compartment lid, or turn on the ignition
within 45 seconds of unlocking the doors
with the remote control. The doors lock
and the alarm will return to its previous
state.
Note: If you double lock your vehicle whilst
inside, switch the ignition on to return the
door locks to a single locked state.
Reprogramming the unlocking function
Note: Your vehicle can be double locked
with a rear door open. The door will be
double locked when it is closed.
The unlocking function may be
reprogrammed so that only the driver’s
door is unlocked ( See Programming the
remote control (page 29). ).
Double locking is a theft protection feature
that prevents someone from opening the
doors from the inside.
32
Locks
Locking and unlocking
confirmation
Locking the doors individually with
the key
Note: If your vehicle has double locking, the
direction indicators will flash once after you
have activated central locking, followed by
two further flashes after double locking.
Note: If the central locking function fails to
operate, the doors can be individually locked
using the key in the position shown.
When you lock the doors, the direction
indicators will flash once.
When you double lock the doors, the
direction indicators will flash three times.
When you unlock the doors, the direction
indicators will flash once.
Locking and unlocking the doors
from inside
E102566
Press the button. For item
location: See At a Glance (page
10).
Luggage compartment lid
Opening the luggage compartment lid
with the remote control
E112203
Left-hand side
Press the button twice within
three seconds.
Turn clockwise to lock.
Right-hand side
Closing the luggage compartment lid
Turn anti-clockwise to lock.
Unlocking
Note: If the child safety locks have also
been activated, pulling the internal lever will
only deactivate the emergency locking and
not the child safety lock. The doors can only
be opened using the external door handle.
Note: If the doors have been unlocked using
this method, the doors must be locked
individually until the central locking function
has been repaired.
Unlock the driver's door using the key. The
other doors can be unlocked individually
by pulling the interior door handles on
those doors.
E133536
33
Locks
Passive key
KEYLESS ENTRY
The vehicle can be locked and unlocked
with the passive key. The passive key can
also be used as a remote control. See
Locking and Unlocking (page 32).
General information
WARNING
The keyless entry system may not
function if the key is close to metal
objects or electronic devices such as
mobile phones.
Locking the vehicle
WARNING
The vehicle does not lock itself
automatically. If the locking function
is not activated, the vehicle will
remain unlocked.
The passive entry system will not function
if:
• The vehicle battery is flat.
• The passive key frequencies are
jammed.
• The passive key battery is flat.
Note: The ignition will automatically switch
off when you lock your vehicle from the
outside. This is to prevent the vehicle battery
from discharging.
Note: If the passive entry system does not
function, you will need to use the key blade
to lock and unlock your vehicle.
Note: Do not grab the door handle.
The keyless system allows the driver to
operate the vehicle without the use of a
key or remote control.
E87384
Touch a front door handle lock sensor to
lock the vehicle.
To activate central locking and arm the
alarm:
• Touch a front door handle lock sensor
once.
E78276
Passive locking and unlocking requires a
valid passive key to be located within one
of the three external detection ranges.
These are located approximately one and
a half metres from the driver and front
passenger door handles and the luggage
compartment lid.
To activate double locking and arm the
alarm:
• Touch a front door handle lock sensor
twice within three seconds.
Note: There must be clearance between
each touch of the door handle.
34
Locks
Note: Once activated, the vehicle will
remain locked for approximately three
seconds. When the delay period is over, the
doors can be opened again, provided the
passive key is within the respective
detection range.
Two short flashes of the direction
indicators confirms that all the doors and
the luggage compartment lid have been
locked and that the alarm has been armed.
Luggage compartment lid
Note: The luggage compartment lid cannot
be closed and, will pop back up if the
passive key is located inside the vehicle with
the doors locked.
E78278
Open any door.
Note: A valid passive key must be located
within the detection range of that door.
Note: If a second valid passive key is
located within the rear exterior detection
range, the luggage compartment lid can be
closed.
One long flash of the direction indicators
confirms that all the doors and the luggage
compartment lid have been unlocked and
that the alarm has been disarmed.
Unlocking the vehicle
Unlocking only the driver's door
Note: If the vehicle remains locked for
longer than three days, the keyless system
will enter an energy-saving mode. This is to
reduce the discharge of the vehicle battery.
When the vehicle is unlocked while in this
mode, the reaction time of the system may
be a little longer than normal. Unlocking the
vehicle once will deactivate the
energy-saving mode.
If the unlocking function is reprogrammed
so that only the driver’s door and the
luggage compartment lid are unlocked (
See Programming the remote control
(page 29). ), note the following:
If the driver’s door is the first door which is
opened, the other doors will remain locked.
All the other doors can be unlocked from
inside the vehicle by pressing the unlock
button on the instrument panel. For item
location: See At a Glance (page 10).
Doors can be unlocked individually by
pulling the interior door handles on those
doors.
Note: If the vehicle remains locked for
several weeks, the keyless system will be
disabled. The vehicle must be unlocked
using the key blade. Unlocking the vehicle
once will enable the keyless system.
Note: Do not touch the front door handle
lock sensor when opening a door.
Disabled keys
Any keys left inside the vehicle interior
when it is locked will be disabled.
A disabled key cannot be used to turn the
ignition on or start the engine.
35
Locks
Global opening
In order to use these passive keys again,
they have to be enabled.
To enable all your passive keys, unlock the
vehicle using a passive key or the remote
control unlocking function.
All passive keys will then be enabled if the
ignition is turned on or the vehicle is started
using a valid key.
Locking and unlocking the doors
with the key blade
E71955
2
To open all the windows, press and hold
the remote control unlock button for at
least three seconds. Press the lock or
unlock button to stop the opening function.
1
Global closing
Vehicles without keyless entry
E87964
WARNING
1
Take care when using global closing.
In an emergency, press the lock or
unlock button immediately to stop.
1. Carefully remove the cover.
2. Remove the key blade and insert it into
the lock.
Note: Only the driver's door handle is fitted
with a lock cylinder.
GLOBAL OPENING AND
CLOSING
You can also operate the electric windows
with the ignition off via the global opening
and global closing function.
Note: Global closing will only operate if you
have set the memory correctly for each
window. See Power Windows (page 63).
E71956
36
Locks
To close all the windows, press and hold
the remote control lock button for at least
three seconds. Press the lock or unlock
button to stop the closing function. The
anti-trap function is also active during
global closing.
Vehicles with keyless entry
E87384
WARNING
Take care when using global closing.
In an emergency, touch a door
handle lock sensor to stop.
Note: Global closing can be activated using
the driver’s door handle. Global opening and
closing can also be activated using the
buttons on the passive key.
To close all the windows, press and hold
the driver’s door handle for at least two
seconds. The anti-trap function is also
active during global closing.
37
Engine immobiliser
PRINCIPLE OF OPERATION
The engine immobiliser is a theft protection
system that prevents someone from
starting the engine with an incorrectly
coded key.
CODED KEYS
Note: Do not shield your keys with metal
objects. This may prevent the receiver from
recognising your key as a valid one.
Note: Have all of your remaining keys
erased and recoded if you lose a key. Ask
your dealer for further information. Have
replacement keys recoded together with
your existing keys.
If you lose a key, you can obtain a
replacement from your Ford Dealer. If
possible, provide them with the key
number from the tag provided with the
original keys. You can also obtain
additional keys from your Ford Dealer.
ARMING THE ENGINE
IMMOBILISER
The engine immobiliser is armed
automatically a short time after you have
switched the ignition off.
DISARMING THE ENGINE
IMMOBILISER
The engine immobiliser is disarmed
automatically when you switch the ignition
on with a correctly coded key.
38
Alarm
Battery back-up sounder
PRINCIPLE OF OPERATION
The battery back-up sounder is an extra
alarm system which will sound a siren
when the alarm is triggered. It is armed
directly when you lock the vehicle. The
sounder has its own battery and will sound
an alarm siren even if someone
disconnects the vehicle battery or the
battery back-up sounder itself.
Alarm system
Your vehicle may be equipped with one of
the following alarm systems:
•
•
•
Perimeter alarm.
Perimeter alarm with interior sensors.
Category one alarm with interior
sensors and battery back-up sounder.
Triggering the alarm
Perimeter alarm
Once armed, the alarm is triggered in any
of the following ways:
The perimeter alarm is a deterrent against
unauthorised access to your vehicle
through the doors and the bonnet. It also
protects the audio unit.
•
•
Interior sensors
•
•
•
If someone opens a door, the tailgate
or the bonnet without a valid key or
remote control.
If someone removes the audio or
navigation system.
If the ignition is turned to position I, II
or III without a valid key.
If the interior sensors detect movement
within the vehicle.
On vehicles with a battery back-up
sounder, if someone disconnects the
vehicle battery or the battery back-up
sounder itself.
If the alarm is triggered, the alarm horn will
sound for 30 seconds and the hazard
warning flasher will flash for five minutes.
E129005
WARNING
Any further attempts to perform one of the
above will trigger the alarm again.
The sensors in the interior lamp unit
must not be covered up. Do not
activate the alarm with full guard if
any persons, animals or other moving
objects are inside the vehicle.
Full and reduced guard
Full guard
Full guard is the standard setting.
The sensors act as a deterrent against
unauthorised intrusion by sensing any
movement within the vehicle.
In full guard, the interior sensors are
activated when you arm the alarm.
Note: This may result in false alarms if
animals or moving objects are inside the
vehicle.
39
Alarm
Note: False alarms can also be triggered
by the auxiliary heater See Auxiliary Heater
(page 102). If you are using the auxiliary
heater, direct the air flow towards the
footwell.
ARMING THE ALARM
Reduced guard
DISARMING THE ALARM
In reduced guard, the interior sensors are
deactivated when you arm the alarm.
Vehicles without keyless entry
Note: You can set the alarm to reduced
guard for the current ignition cycle only. The
next time you switch on the ignition, the
alarm will be reset to full guard.
Perimeter alarm
To arm the alarm, lock the vehicle. See
Locks (page 32).
Disarm and silence the alarm by unlocking
the doors with the key and switching the
ignition on with a correctly coded key, or
unlocking the doors or the luggage
compartment lid with the remote control.
Ask on Exit
You can set the information display to ask
you each time which level of guard you
wish to set.
Category one alarm
Disarm and silence the alarm by unlocking
the doors with the key and switching the
ignition on with a correctly coded key
within 12 seconds, or unlocking the doors
or the luggage compartment lid with the
remote control.
If you select Ask on Exit, the message
Reduced guard? appears in the
instrument cluster display each time you
switch the ignition off.
If you wish to arm the alarm with reduced
guard, press the OK button when this
message appears.
Vehicles with keyless entry
If you wish to arm the alarm with full guard,
leave the vehicle without pressing the OK
button.
Note: A valid passive key must be located
within the detection range of that door for
keyless entry. See Keyless Entry (page 34).
Selecting full or reduced guard
Perimeter alarm
Note: Selecting Reduced does not set the
alarm permanently to reduced guard. It sets
it to reduced guard only for the current
ignition cycle. If you regularly set the alarm
to reduced guard, select Ask on Exit.
Disarm and silence the alarm by unlocking
the doors and switching the ignition on, or
unlocking the doors or the luggage
compartment lid with the remote control.
Category one alarm
You can select full or reduced guard using
the information display. See General
Information (page 75).
Disarm and silence the alarm by unlocking
the doors and switching the ignition on
within 12 seconds, or unlocking the doors
or the luggage compartment lid with the
remote control.
Information messages
See Information Messages (page 83).
40
Steering Wheel
ADJUSTING THE STEERING
WHEEL
WARNING
Make sure that you fully engage the
locking lever when returning it to its
original position.
WARNING
Never adjust the steering wheel
when the vehicle is moving.
AUDIO CONTROL
Select the required source on the audio
unit.
Note: Make sure that you are sitting in the
correct position. See Sitting in the Correct
Position (page 105).
The following functions can be operated
with the remote control:
Type 1
2
A
E
2
B
D
1
E95178
C
E129462
A
Volume up
B
Seek up or next
C
Volume down
D
Seek down or previous
E
Mode
Press the mode button to select the audio
source.
3
E95179
41
Steering Wheel
Type 2
VOICE CONTROL
A
D
C
B
E129463
E129464
A
Volume up
B
Seek up or next
C
Volume down
D
Seek down or previous
Pull the button to select or deselect voice
control. See Voice control (page 249).
Seek, next or previous
Press the seek button to:
• tune the radio to the next or previous
stored preset
• play the next or the previous track.
Press and hold the seek button to:
• tune the radio to the next station up or
down the frequency band
• seek through a track.
42
Wipers and Washers
Automatic wiper system
WINDSCREEN WIPERS
Some models without autowipers are
fitted with a speed-dependent front screen
wiper system.
D
C
When the vehicle is slowed to walking
speed or is brought to a standstill, the
wiper speed will automatically switch to
the next lower wiper speed setting.
B
When the vehicle speed is increased, the
wiper speed will return to the
manually-chosen setting.
Moving the wiper lever when the system is
operating will switch off the system.
A
If the vehicle is again slowed to walking
speed or is brought to a standstill, the
system is reactivated.
E128444
A
Single wipe
B
Intermittent wipe or autowipers
C
Normal wipe
D
High speed wipe
AUTOWIPERS
CAUTIONS
Do not switch autowipers on in dry
weather conditions. The rain sensor
is very sensitive and the wipers may
operate if dirt, mist or flies hit the
windscreen.
Intermittent wipe
A
B
Replace the wiper blades as soon as
they begin to leave bands of water
and smears. If you do not replace
them, the rain sensor will continue to
detect water on the windscreen and the
wipers will operate, even though the
majority of the windscreen is dry.
C
Fully defrost the windscreen in icy
conditions before you switch
autowipers on.
E128445
A
Short wipe interval
B
Intermittent wipe
C
Long wipe interval
Switch autowipers off before you
enter a car wash.
Note: If autolamps have been switched on
in conjunction with autowipers, dipped
headlamps will illuminate automatically
when the rain sensor activates the
windscreen wipers continuously.
The rotary control can be used to adjust
the intermittent wipe interval.
43
Wipers and Washers
A
WARNING
B
Do not operate the washer for more
than 10 seconds at a time, and never
when the reservoir is empty.
Whilst the lever is pulled towards the
steering wheel the washer will work in
conjunction with the wipers.
C
After releasing the lever, the wipers
operate for a short time.
E128445
A
High sensitivity
B
On
C
Low sensitivity
REAR WINDOW WIPER AND
WASHERS
Intermittent wipe
If you switch autowipers on, the wipers will
not cycle until water is detected on the
windscreen. The rain sensor will then
continuously measure the amount of water
on the windscreen and adjust the speed
of the wipers automatically.
Adjust the sensitivity of the rain sensor
using the rotary control. With low
sensitivity, the wipers will operate when
the sensor detects a lot of water on the
windscreen. With high sensitivity, the
wipers will operate if the sensor detects a
small amount of water on the windscreen.
A B
WINDSCREEN WASHERS
E129193
A
Intermittent wipe
B
Low speed wipe
Press the button at the end of the lever to
change between off, intermittent and low
speed.
E129188
44
Wipers and Washers
Reverse gear wipe
CHECKING THE WIPER
BLADES
The rear wiper will be activated
automatically when selecting reverse gear
if the rear wiper is not already switched on
and the front wiper is operating.
Rear window washer
E66644
Run the tip of your fingers over the edge of
the blade to check for roughness.
E129194
WARNING
Clean the wiper blade lips with water
applied with a soft sponge.
Do not operate the washer for more
than 10 seconds at a time, and never
when the reservoir is empty.
CHANGING THE WIPER
BLADES
While the lever is pushed away from the
steering wheel the washer will work in
conjunction with the wipers.
Windscreen wiper blades
After releasing the lever, the wipers
operate for a short time.
CAUTIONS
Set the windscreen wipers in the
service position to change the wiper
blades.
HEADLAMP WASHERS
You can use the service position in
winter to provide easier access to the
wiper blades for freeing them from
snow and ice. The windscreen wipers will
return to their normal position as soon as
you switch on the ignition so make sure
that the outside of the windscreen is free
from snow and ice before you switch on
the ignition.
The headlamp washers will operate with
the windscreen washers when the
headlamps are on.
Note: To stop the washer fluid reservoir
emptying quickly, the headlamp washers
will not operate every time that you use the
windscreen washers.
45
Wipers and Washers
Rear window wiper blade
Service position
1.
Lift the wiper arm.
3
4
E75184
2
E86456
2. Position the wiper blade at right angles
to the wiper arm.
3. Disengage the wiper blade from the
wiper arm.
4. Remove the wiper blade.
Note: Make sure that the wiper blade locks
into place.
A
E129986
Switch off the ignition and move the wiper
lever to position A within three seconds.
Release the lever when the windscreen
wipers have moved to the service position.
5. Install in the reverse order.
Changing the windscreen wiper blades
Set the windscreen wipers in the service
position and lift the wiper arms.
2
1
E72899
Install in the reverse order.
Note: Make sure that the wiper blade locks
into place.
46
Lighting
One side
LIGHTING CONTROL
A
Lighting control positions
A
B
C
B
E130139
E132706
A
Off
B
Side and tail lamps
C
Headlamps
A
Right-hand side
B
Left-hand side
Main and dipped beam
Parking lamps
WARNING
Prolonged use of the parking lamps
will discharge the battery.
Switch off the ignition.
E130140
Both sides
Push the lever forward to switch between
main and dipped beam.
Turn the lighting control switch to position
B.
Headlamp flasher
Pull the lever slightly towards the steering
wheel.
47
Lighting
Home safe lighting
The headlamps will come on and go off
automatically depending on the ambient
light.
Switch the ignition off and pull the
direction indicator lever towards the
steering wheel to switch the headlamps
on. You will hear a short tone. The
headlamps will go off automatically after
three minutes with any door open, or 30
seconds after the last door has been
closed.
The headlamps will remain on for a period
of time after you switch the ignition off.
You can adjust the time delay using the
information display. See Information
Displays (page 75).
AUTOMATIC MAIN BEAM
CONTROL
The home safe lights can be cancelled by
either pulling the direction indicator lever
towards the steering wheel again or by
turning the ignition switch ON.
WARNINGS
The system does not relieve you of
your responsibility to drive with due
care and attention. A manual
override may be necessary if the system
fails to switch the main beam on or off.
AUTOLAMPS
WARNING
In severe weather conditions, it may
be necessary to switch your
headlamps on manually.
A manual override may be required
when approaching other road users
such as cyclists.
Do not use the system in fog.
Note: If you have switched autolamps on,
you can only switch the main beam on when
autolamps has switched the headlamps on.
Note: If autolamps have been switched on
in conjunction with autowipers, dipped
headlamps will illuminate automatically
when the rain sensor activates the
windscreen wipers continuously.
CAUTIONS
In cold and severe weather conditions
the system may not function. A
manual override may be necessary in
these cases.
Reflective road signs may be detected
as oncoming traffic and the
headlamps may be switched to
dipped beam.
If the lights of oncoming vehicles are
hidden by obstacles (for example
guard rails) the system may not
deactivate the main beam.
Always fit Ford Original Parts when
replacing headlamp bulbs. Other
bulbs may reduce system
performance.
E132707
48
Lighting
Activating the system
CAUTIONS
Check and replace wiper blades
regularly to ensure the camera sensor
has a clear view through the
windscreen. Replacement wiper blades
must be the correct length.
Switch on the system using the information
display and autolamps. See Information
Displays (page 75). See Autolamps
(page 48).
Note: Keep the windscreen free from
obstructions such as bird droppings, insects
and snow or ice.
The system will automatically switch on
main beam if it is dark enough and no other
traffic is present. If it detects an
approaching vehicle’s headlamps or tail
lamps, or street lighting ahead the system
will switch off main beam before it can
distract other road users. Dipped beams
will remain on.
A camera sensor is centrally mounted
behind the windscreen of the vehicle, and
monitors conditions continuously to decide
when to switch the main beam off and on.
E132707
Turn the switch to the autolamps position.
Note: The system may take a short time to
initialise after first switching the ignition on,
especially in very dark conditions. The main
beam will not automatically switch on
during this period.
Once the system is active the main beam
will switch on if:
• It is dark enough to require the use of
main beams and
• there is no traffic or street lighting
ahead and
• vehicle speed is greater than 40 km/h
(25 mph).
Setting the system sensitivity
The system has three sensitivity levels
which can be accessed via the information
display. See Information Displays (page
75).
The main beam will switch off if:
• The ambient light is high enough that
main beam is not required.
• An approaching vehicle's headlamps
or tail lamps are detected.
• Street lighting is detected.
• Vehicle speed falls below 25 km/h (16
mph).
• The camera sensor is too hot or
becomes blocked.
The sensitivity determines the speed at
which the main beam will be restored after
detected traffic leaves the field of view.
49
Lighting
Manually overriding the system
E133632
Push or pull the lever to switch between
main and dipped beam.
E132709
Note: This is a temporary override and the
system will return to automatic operation
after a short period.
REAR FOG LAMPS
WARNINGS
Only use the rear fog lamps when
visibility is restricted to less than 50
metres (164 feet).
To permanently deactivate the system use
the information display menu or turn the
lighting control switch from autolamps to
headlamps.
Do not use the rear fog lamps when
it is raining or snowing and visibility
is more than 50 metres (164 feet).
FRONT FOG LAMPS
WARNING
Only use the front fog lamps when
visibility is considerably restricted by
fog, snow or rain.
E132710
50
Lighting
ADJUSTING THE HEADLAMPS
- VEHICLES WITH: ADAPTIVE
FRONT LIGHTING/XENON
HEADLAMPS
2
To adjust the headlamps for driving on the
left or right hand side of the road, see your
dealer.
2
1
HEADLAMP LEVELLING
Note: Vehicles with Xenon headlamps are
equipped with automatic headlamp
levelling.
1.
E132711
2. Rotate the button to the required
setting.
3. Push the button to the closed position.
Press to release the pop out button.
You can adjust the level of the headlamp
beams according to the vehicle load.
Recommended headlamp levelling switch positions
Load
1
Load in luggage
compartment
Switch position
-
-
0
2
3
-
1
2
3
Max
1
-
Max
Front seats
Second row seats
1-2
See Vehicle identification (page 221).
HAZARD WARNING FLASHERS
E71943
For item location: See At a Glance (page
10).
51
1
2
1
3
Lighting
Note: Tap the lever up or down to make the
direction indicators flash only three times.
DIRECTION INDICATORS
E130141
CORNERING LAMPS
A
A
B
B
E72898
A
Headlamp beam
B
Cornering lamp beam
52
Lighting
The cornering lamps illuminate the inside
of a corner when you are turning.
If you press switch B all lamps remain off
when the door is opened. Press the switch
again to reverse.
INTERIOR LAMPS
You can control all lamps using switch C.
Interior lighting
Centre mounted lamp
Note: Individual lamps may be switched on
independently, but not off if all lamps have
been switched on by the driver.
B
A
Note: All other lamps will be either
non-switchable or with individual reading
or dome lamp functionality only.
The lamps will come on when you unlock
or open a door or the luggage
compartment lid. If you leave a door open
with the ignition switch off, all lamps will
go off automatically after some time to
prevent the vehicle battery from
discharging. To switch them back on,
switch on the ignition for a short time.
E139420
Side mounted lamp
A
D
C
A
Right-hand side reading lamp on
and off switch
B
Left-hand side reading lamp on
and off switch
C
Door function switch
D
All lamps on and off switch
If you press switch C all lamps remain off
when the door is opened. Press the switch
again to reverse.
You can control all lamps using switch D.
Ambient lighting
E139419
C
If you leave a door open with the ignition
switch off, the ambient lamp will go off
automatically after some time to prevent
the vehicle battery from discharging.
B
A
Reading lamp on and off switch
B
Door function switch
C
All lamps on and off switch
If dark, the ambient lights are active if the
ignition and headlamps are switched on.
53
Lighting
Type 1
1.
Ambient lighting illuminates several areas,
for example footwells, cup holders and
doors with a single colour and can be
switched on and off using the information
display menu. See General Information
(page 75).
Open the bonnet. See Opening and
Closing the Bonnet (page 190).
2
Use the instrument lighting dimmer
switches to adjust to the desired
brightness. See Instrument Lighting
Dimmer (page 111).
4
Type 2
2
3
E133215
2. Remove the screws.
3. Pull the headlamp as far as possible
towards the front of the vehicle to
disengage it from the lower fixing point.
4. Lift the outer side of the headlamp and
remove it.
E133092
Ambient lighting illuminates several areas,
for example footwells, cup holders and
doors with a choice of several colours. The
ambient lighting control switch is located
in the overhead console.
To activate, rotate the control knob and
adjust to the desired brightness. Use the
left switch to cycle through the colour
choices. Use the right switch to activate
all ambient light areas and interior lamps.
REMOVING A HEADLAMP
WARNING
5
Have Xenon bulbs changed by a
trained technician. There is a risk of
electric shock.
E133750
5. Disconnect the electrical connector.
54
Lighting
Note: When fitting the headlamp, make
sure that you reconnect the electrical
connector properly.
A
B
C
D
Note: When fitting the headlamp, make
sure that you fully engage the headlamp in
the lower fixing point.
Note: When fitting the headlamp, make
sure that the screw is located in the
headlamp moulding before you install it.
E133102
CHANGING A BULB
WARNINGS
Switch the lights and the ignition off.
Let the bulb cool down before
removing it.
A
Side lamp
B
Headlamp dipped beam
C
Headlamp main beam
D
Direction indicator
Direction indicator
Have Xenon bulbs changed by a
properly trained technician. There is
a risk of electric shock.
1.
Remove the headlamp. See
Removing a Headlamp (page 54).
3
CAUTIONS
Do not touch the glass of the bulb.
Only fit bulbs of the correct
specification. See Bulb
Specification Chart (page 62).
Note: The following instructions describe
how to remove the bulbs. Fit replacements
in the reverse order unless otherwise stated.
Headlamp
E133104
Note: Remove the covers to gain access to
the bulbs.
2
2. Remove the cover.
3. Turn the bulb holder anti-clockwise
and remove it.
4. Gently press the bulb into the bulb
holder, turn it anti-clockwise and
remove it.
55
Lighting
Headlamp main beam
2
4
CAUTION
Do not touch the glass of the bulb.
1.
Remove the headlamp. See
Removing a Headlamp (page 54).
2
4
E133106
2. Remove the cover.
3. Disconnect the electrical connector.
4. Release the clip and remove the bulb.
E133105
Side Lamp
2. Remove the cover.
3. Disconnect the electrical connector.
4. Release the clip and remove the bulb.
1.
Remove the headlamp. See
Removing a Headlamp (page 54).
3
Headlamp dipped beam
CAUTION
Do not touch the glass of the bulb.
1.
Remove the headlamp. See
Removing a Headlamp (page 54).
E133103
2
2. Remove the cover.
3. Remove the bulb holder.
4. Remove the bulb.
56
Lighting
Side repeater
1
E133426
1.
Carefully remove the cover.
E133109
4. Remove the bulb holder.
5. Remove the bulb.
Approach lamp
CAUTION
When removing the mirror glass, take
care not to break it.
Note: Position the mirror glass as far
inwards as possible.
E133427
2. Using a suitable implement release the
retaining clip.
E133108
E133110
3. Carefully remove the side repeater.
57
Lighting
1.
Insert your fingers into the gap between
the mirror housing and the mirror glass
and pull gently to remove the mirror
glass.
3
2
E133717
2. Remove the lamp.
2
E133107
E133718
3
Note: You cannot separate the fog lamp
bulb from the bulb holder.
3. Remove the bulb.
2. Disconnect the electrical connector.
3. Turn the bulb holder anti-clockwise
and remove it.
Front fog lamps
1.
Remove the headlamp. See
Removing a Headlamp (page 54).
Rear lamps - 5 door
E133111
1.
58
Remove the trim panel.
Lighting
A
B
2
C
D
E133112
E133113
2. Remove the wing nuts and detach the
clip.
3. Remove the lamp.
5. Remove the bulb holder.
6. Gently press the bulb into the bulb
holder, turn it anti-clockwise and
remove it.
A. Brake lamp
B. Reversing lamp
C. Tail and fog lamp
D. Direction indicator
4
Rear lamps - 4 door
Direction indicator, tail and fog lamp
E133127
4. Disconnect the electrical connector.
E133702
1.
59
Remove the trim panel.
Lighting
6. Gently press the bulb into the bulb
holder, turn it anti-clockwise and
remove it.
A. Tail and fog lamp
B. Direction indicator
Brake and reversing lamp
1.
2
Open the luggage compartment lid.
x10
2
E133703
2. Remove the wing nuts and detach the
clip.
3. Remove the lamp.
E133724
2. Remove the luggage compartment lid
trim.
4
E133713
3
4. Disconnect the electrical connector.
B
E133725
E133714
CAUTION
A
Unclip the outboard side first.
5. Remove the bulb holder.
60
Lighting
Number plate lamp
3. Remove the wing nut and detach the
2 clips.
4. Remove the lamp.
Note: These are not serviceable items,
please consult your dealer if they fail.
Interior lamps
Vehicles with LED lamps
Note: The LED board is not a serviceable
item, please consult your dealer if this fails.
5
E133726
5. Disconnect the electrical connector.
B
E125092
Luggage compartment lamp,
footwell lamp and tailgate lamp
A
E133727
6. Remove the bulb holder.
7. Gently press the bulb into the bulb
holder, turn it anti-clockwise and
remove it.
A. Brake lamp
B. Reversing lamp
Central high mounted brake lamp
Note: These are not serviceable items,
please consult your dealer if they fail.
E72784
1. Carefully prise out the lamp.
2. Remove the bulb.
61
Lighting
BULB SPECIFICATION CHART
Lamp
Specification
Power (watt)
PY21W
21
Headlamp main beam
H1
55
Headlamp dipped beam
H7
55
Cornering lamp
H1
55
Front fog lamp
H11
55
W5W
5
WY5W
5
Front direction indicator
Side lamp
Side repeater
Approach lamp
1
W5W
5
Rear direction indicator
PY21W
21
Brake and tail lamp
P21/5W
21/5
W5W
5
Tail lamp
Rear fog lamp
P21W
21
Reversing lamp
W16W
16
Luggage compartment lamp
W5W
5
1
Fit a replacement with the same rating as the one you have removed.
62
Windows and Mirrors
POWER WINDOWS
Opening and closing the windows
automatically
WARNING
Press or lift the switch to the second action
point and release it completely. Press or
lift it again to stop the windows.
Do not operate the electric windows
unless they are free from obstruction.
Safety switch for rear windows
Note: If you operate the switches often
during a short period of time, the system
might become inoperable for a certain time
to prevent damage due to overheating.
WARNING
On some vehicles, pressing the
switch will also lock the rear doors
from inside. See Child Safety
Locks (page 22).
Switch on the ignition to operate the
electric windows.
Global opening and closing
Note: You can always operate the rear
windows from the driver’s door.
You can also operate the electric windows
with the ignition off via the global opening
and closing function. See Locks (page
32).
Driver's door switches
You can operate all the windows with the
switches on the door trim panel of the
driver’s door.
E70850
A switch in the driver’s door disables the
rear electric window switches.
The light in the switch comes on and the
lights in the rear window switches go off
when the rear windows are disabled.
Anti-trap function
E70848
WARNING
Careless closing of the windows can
override the protection function and
cause injuries.
63
Windows and Mirrors
3. Lift the switch again for one more
second.
4. Push and hold the switch until the
window is fully open.
5. Release the switch.
6. Lift and hold the switch until the
window is fully closed.
7. Open the window and try to close it
automatically.
8. Reset and repeat procedure if the
window does not close automatically.
The electric windows will stop
automatically while closing and reverse
some distance if there is an obstacle in the
way.
Overriding the anti-trap function
WARNING
While you close the window for the
third time, the anti-trap function is
disabled. Make sure there are no
obstacles in the way of the closing window.
To override this protection function when
there is a resistance, e.g. in the winter,
proceed as follows:
EXTERIOR MIRRORS
WARNING
1.
Close the window twice until it reaches
the resistance and let it reverse.
2. Close the window a third time to the
resistance. The anti-trap function is
disabled and you cannot close the
window automatically. The window
will override the resistance and you can
close it fully.
3. If the window does not close after the
third attempt, have it checked by an
expert.
Do not overestimate the distance of
the objects that you see in the
convex mirror. Objects seen in
convex mirrors will appear smaller and
further away than they actually are.
Manual folding mirrors
Folding
Push the mirror towards the door window
glass.
Resetting the memory of the
electric windows
Unfolding
Make sure that you fully engage the mirror
in its support when returning it to its
original position.
WARNING
The anti-trap function is deactivated
until you have reset the memory.
After the battery has been disconnected
from the vehicle you must reset the
memory separately for each window:
Note: On vehicles with a convertible top,
the roof and doors must be fully closed
before carrying out the following procedure.
1.
Lift and hold the switch until the
window is fully closed.
2. Release the switch.
64
Windows and Mirrors
Electric folding mirrors
ELECTRIC EXTERIOR
MIRRORS
Automatic folding and unfolding
Note: If the mirrors have been folded using
the manual fold button they can only be
unfolded using the manual fold button.
The mirrors will fold automatically when
you lock the vehicle with the key, the
remote control or a keyless entry system
request. The mirrors will unfold when you
unlock the vehicle with the key, the remote
control, a keyless entry system request,
the driver's interior door handle or starting
the engine.
A
C
Manual folding and unfolding
B
E70846
A
Left-hand mirror
B
Off
C
Right-hand mirror
The electric folding mirrors operate with
the ignition on.
Note: You can operate the mirrors (mirror
tilting and folding) for several minutes after
you switch off the ignition. They will be
deactivated as soon as a door is opened.
Mirror tilting positions
E70847
E72623
The electric exterior mirrors are fitted with
a heating element that will defrost or
demist the mirror glass. See Heated
Windows and Mirrors (page 100).
Press the button to fold or unfold the
mirrors.
65
Windows and Mirrors
If you press the switch again while the
mirrors are moving, they will stop and
reverse the direction of movement.
The system is a convenience feature that
aids the driver in detecting vehicles that
may have entered the blind spot zone (A).
The detection area is on both sides of the
vehicle extending rearwards from the
exterior mirrors to approximately 3 metres
(10 feet) beyond the bumper. The system
will alert you if certain vehicles enter the
blind spot zone whilst driving.
Note: When the mirrors are operated often
during a short period of time, the system
may become inoperable for a period of time
to prevent damage due to overheating.
AUTO-DIMMING MIRROR
A
E71028
A
The auto-dimming mirror will adjust
automatically when hit by glaring light
from behind. It will not work when you have
selected reverse gear.
E124788
Using the system
BLIND SPOT MONITOR
The system displays a yellow indicator
located in the exterior mirrors.
Blind spot information system
(BLIS)
WARNINGS
The system is not designed to
prevent contact with other vehicles
or objects. The system only provides
a warning to assist you in detecting
vehicles in the blind spot zones. The
system will not detect obstacles,
pedestrians, motorcyclists or cyclists.
Do not use the system as a
replacement for using the side and
rear view mirrors, and looking over
your shoulder before changing lanes. The
system is not a replacement for careful
driving and is only to be used as an aid.
E124736
Note: Both indicators will illuminate briefly
when you switch the ignition on to confirm
that the system is operational.
66
Windows and Mirrors
Note: On vehicles with automatic
transmission, the system is active only in S,
D and N.
Detection limitations
There may be certain instances where
vehicles entering and exiting the blind spot
zones may not be detected.
The system is only active when you exceed
10 km/h (6 mph). The system is
temporarily deactivated when you select
reverse gear.
Instances which may cause non-detection:
• Debris build up on the rear bumper
panels in the area of the sensors.
• Certain manoeuvring of vehicles
entering and exiting the blind zone.
• Vehicles passing through the blind zone
at high speed.
• Severe weather conditions.
• Several vehicles passing through the
blind zone following each other closely.
System detection and alerts
The system will trigger the alert for vehicles
that enter the blind spot zone from the rear
or merge from the side. Vehicles that you
pass, or vehicles that enter the blind spot
zone from the front, will only trigger the
alert after the vehicle has remained in the
blind spot zone for a short period of time.
Note: Vehicles that pass through the blind
zone quickly (typically less than 2 seconds)
will not trigger the alert.
False alerts
Note: False alerts are temporary and will
self correct.
The system consists of two radar sensors
each located behind the rear wheels
hidden behind the bumpers.
There may be certain instances when the
system will alert with no vehicle present in
the blind zone.
CAUTIONS
Do not place items such as bumper
stickers in this area.
Circumstances where false alerts may
occur:
• Road guardrails.
• Motorway concrete walls.
• Construction areas.
• Sharp turns around a building.
• Bushes and trees.
• Cyclists and motorcyclists.
• Coming to a stop with a vehicle directly
behind but very close.
Repairs to these areas using body filler
will affect the performance of the
system.
Turning the system on and off
Note: The on or off position will remain until
manually changed.
You can turn the system on and off using
the information display. See Information
Displays (page 75).
E124741
67
Windows and Mirrors
When you turn the system off no further
alerts will be received. The BLIS warning
indicator will illuminate. See Warning
Lamps and Indicators (page 71).
Trailer towing false alerts
CAUTION
Vehicles fitted with a trailer tow
module not approved by us may not
correctly be detected. Switch the
system off to avoid false alerts. See
Information Displays (page 75).
Detection errors
Note: The alert indicator in the mirror will
not illuminate.
If the system senses a fault on either
sensor, the system warning symbol will
illuminate and remain on. The information
display will confirm the fault and indicate
whether the left or right side is affected.
If the vehicle is fitted with a trailer tow
module approved by us, the system will
detect a connected trailer and deactivate.
A confirmation message will be shown in
the information display. See Information
Messages (page 83). The BLIS warning
indicator will illuminate. See Warning
Lamps and Indicators (page 71).
Blocked sensor
WARNING
Prior to the system recognizing a
blocked condition and issuing a
warning, the number of missed
objects will increase.
CAUTION
The sensors may not detect vehicles
in heavy rain or other conditions that
cause disruptive reflections.
Note: Keep the rear bumper area
surrounding the sensors free from dirt, ice
and snow.
If a sensor becomes blocked the system
performance may degrade. A blocked
sensor message may be displayed.
The system will automatically return to
normal operation once two other vehicles
have been detected on both sides.
68
Instrument Cluster
GAUGES
Type 1
A
F
E
D
C
E132065
A
Information display. See Information Displays (page 75).
B
Speedometer
C
Engine coolant temperature gauge
D
Tripmeter reset button
E
Fuel gauge
F
Tachometer
69
B
Instrument Cluster
Type 2 and 3
A
E
D
C
B
E130149
A
Information display. See Information Displays (page 75).
B
Speedometer
C
Engine coolant temperature gauge
D
Fuel gauge
E
Tachometer
If the needle enters the red section, the
engine is overheating. Stop the engine,
switch the ignition off and determine the
cause once the engine has cooled down.
See Engine Coolant Check (page 199).
Engine coolant temperature gauge
All vehicles
Shows the temperature of the engine
coolant. At normal operating temperature,
the needle will remain in the centre section.
Fuel gauge
The arrow adjacent to the fuel pump
symbol indicates on which side of the
vehicle the fuel filler cap is located.
CAUTION
Do not restart the engine until the
cause of overheating has been
resolved.
70
Instrument Cluster
Brake system lamp
WARNING LAMPS AND
INDICATORS
It illuminates when the parking
brake is engaged.
The following warning lamps and
indicators illuminate when the ignition is
switched on:
•
•
•
•
•
•
•
WARNING
Reduce your speed gradually and
stop your vehicle as soon as it is safe
to do so. Use your brakes with care.
Airbag
ABS
Stability control (ESP)
Low fuel
Brake system
Frost
ESP off
If it illuminates when you are driving, check
that the parking brake is not engaged. If
the parking brake is not engaged, this
indicates a malfunction. Have the system
checked by a properly trained technician
immediately.
If a warning or indicator lamp does not
illuminate when the ignition is switched
on, it indicates a malfunction. Have the
system checked by properly trained
technician.
Cruise control indicator
It will illuminate when you have
set a speed using the cruise
E71340
control system. See Using
Cruise Control (page 146).
ABS warning lamp
If it illuminates when you are
driving, this indicates a
malfunction. You will continue
to have normal braking (without ABS).
Have the system checked by a properly
trained technician as soon as possible.
Direction indicators
Flashes during operation. A
sudden increase in the rate of
flashing warns of a failed
indicator bulb. See Changing a Bulb
(page 55).
Airbag warning lamp
Engine warning lamp
If it illuminates when you are
driving, this indicates a
malfunction. Have the system
checked by a properly trained technician.
If it illuminates with the engine
running, this indicates a
malfunction. If it flashes when
you are driving, reduce the speed of your
vehicle immediately. If it continues to
flash, avoid heavy acceleration or
deceleration. Have the system checked by
a properly trained technician immediately.
Blind spot monitor indicator
It will illuminate when this
feature is deactivated or in
E124823
conjunction with a message.
See Blind Spot Monitor (page 66). See
Information Messages (page 83).
CAUTION
If the engine warning lamp illuminates
in conjunction with a message, have
the system checked as soon as
possible.
71
Instrument Cluster
Forward alert warning indicator
Lane departure warning indicator
It will illuminate when this
feature is switched off or in
conjunction with a message.
See Forward alert function (page 152).
It will illuminate when this
feature is switched off or in
conjunction with a message.
See Lane Departure Warning (page 156).
Front fog lamp indicator
Low fuel level warning lamp
It will illuminate when you switch
the front fog lamps on.
If it illuminates, refuel as soon as
possible.
Low tyre pressure warning lamp
Frost warning lamp
See Tyre Pressure Monitoring
System (page 217).
WARNING
Even if the temperature rises to
above +4°C (39°F) there is no
guarantee that the road is free of
hazards caused by inclement weather.
Main beam indicator
It will illuminate when you switch
the headlamp main beam on. It
will flash when you use the
headlamp flasher.
It will illuminate and glow amber
when the outside air
temperature is between +4°C
(39°F) and 0°C (32°F). It will glow red
when the temperature is below 0°C
(32°F).
Message indicator
It will illuminate when a new
message is stored in the
information display. See
Information Messages (page 83).
Glow plug indicator
See Starting a Diesel Engine
(page 116).
Oil pressure warning lamp
Headlamp indicator
CAUTION
Do not resume your journey if it
illuminates despite the level being
correct. Have the system checked by
a properly trained technician immediately.
It will illuminate when you switch
the headlamp dipped beam or
the side and tail lamps on.
Ignition warning lamp
If it stays on after starting or
illuminates when driving, this
indicates a malfunction. Stop
your vehicle as soon as it is safe to do so
and switch the engine off. Check the engine
oil level. See Engine Oil Check (page 198).
If it illuminates when you are
driving, this indicates a
malfunction. Switch off all
unnecessary electrical equipment. Have
the system checked by a properly trained
technician immediately.
72
Instrument Cluster
Rear fog lamp indicator
1.
It will illuminate when you switch
the rear fog lamps on.
2.
Seat belt reminder
3.
See Seat belt reminder (page
26).
4.
Stability control (ESP) indicator
5.
While driving, it flashes during
activation of the system. After
switching on the ignition, if it
does not illuminate or illuminates
continuously while driving, this indicates a
malfunction. During a malfunction, the
system switches off. Have the system
checked by a properly trained technician
as soon as possible.
Press the left arrow button on the
steering wheel to enter the main menu.
Highlight Settings with the up and
down arrow buttons and press the right
arrow button.
Highlight Chimes and press the right
arrow button.
Highlight Information or Warning and
press the OK button to switch the
chime on and off.
Press the left arrow button to exit the
menu. Press and hold the left arrow
button to return to the main menu
display.
Automatic transmission
If position P is not selected, a warning
chime will sound when the driver’s door is
opened.
Frost
If you switch traction control off,
the warning lamp will illuminate.
The lamp will go out when you
switch the system back on or when you
switch the ignition off.
WARNING
Even if the temperature rises to
above +4°C (39°F) there is no
guarantee that the road is free of
hazards caused by inclement weather.
Start-stop indicator
It will illuminate to inform you
when the engine shuts down or
in conjunction with a message.
See Using start-stop (page 120). See
Information Messages (page 83).
A warning chime will sound in the following
conditions:
• +4°C (39°F) or lower: frost warning.
• 0°C (32°F) or lower: danger of icy
roads.
AUDIBLE WARNINGS AND
INDICATORS
Key outside car
Switching the chimes on and off
If the engine is running and a passive key
is no longer detected within the vehicle
interior, a warning chime will sound.
Vehicles with keyless entry
You can deactivate certain chimes in the
Information display using the steering
wheel control. For item location: See At a
Glance (page 10).
To set which chimes should sound:
73
Instrument Cluster
Door open
A warning chime will sound when any door
is opened if the vehicle exceeds a relatively
low speed.
Lights on
A warning chime will sound if the driver’s
door is opened with the exterior lights
switched on and the ignition switched off.
Low fuel
A warning chime will sound when the
remaining fuel is less than approximately
6 litres (1.3 gallons).
Seat belt reminder
See Seat belt reminder (page 26).
74
Information Displays
GENERAL INFORMATION
Phone
Note: The information display will remain
on for several minutes after you switch off
the ignition.
Settings
Various systems on your vehicle can be
controlled using the information display
controls on the steering column.
Corresponding information is displayed in
the information display.
Controls
Press the up and down arrow buttons to
scroll through and highlight the options
within a menu.
For detailed instructions on navigation,
refer to the appropriate manual.
Press the right arrow button to enter a
sub-menu.
Device list
Press the left arrow button to exit a menu.
The icon changes to show the current
function in use.
Hold the left arrow button pressed at any
time to return to the main menu display
(escape button).
CD
Press the OK button to choose and
confirm a setting.
Radio
Menu structure - information
display
Auxiliary input
All vehicles
You can access the menu using the
Information display control. For item
location: See At a Glance (page 10).
75
Information Displays
Trip Computer
Trip odometer
Dist to empty
Instant fuel
Average fuel
Ford EcoMode
Gear shifting
Anticipation
Speed
Ford EcoMode
Average speed
Outside air
All values
Information
Seatbelts
Auto StartStop
Driver Alert
Traffic signs
Settings
Driver assist
Traction ctrl
BLIS
City Stop
Forward alert
Driver alert
Hill start assist
Deflation detection
Traffic signs
Lane departure
Auto light rain
Ambient light
Dimming
Lighting
Auto highbeam
Hdlamp delay
A
B
E133367
76
High Sensitivity
Normal Sens
Low Sensitivity
Off
Recognition
Speed warning
Sensitivity
Intensity
Auto
Manual
Set
On
Sensitivity
Manual
20 seconds
40 seconds
60 seconds
Information Displays
A
B
Display
Navigation info
Always on
On demand
Always off
Language
English
Deutsch
Italiano
Français
Español
Türkçe
Pyccкий
Nederlands
Polski
Svenska
Português
Measure unit
l/100km
Miles/Gallon
Temp unit
°Celsius
°Fahrenheit
Chimes
Park slot found
Information
Warning
Convenience
Aux heater
Park heater
Alarm
System check
E133368
77
Time 1
Time 2
Once
Heat now
Full guard
Reduced
Ask on exit
Information Displays
Menu structure - information and
entertainment display
You can access the menu using the
buttons on the audio or navigation unit.
All vehicles
CD
Radio
FM
FM AST
DAB1
DAB2
AM
AM AST
Auxiliary
iPOD
USB
Bluetooth audio
Line in
Phone
Dial number
Phone book
Call lists
Bluetooth
Redial
Select phone
Reject all calls
Menu
Audio settings
Adaptive volume
Sound
Nav audio mixing
DSP settings
DSP equaliser
News
Alt frequency
RDS regional
DAB service link
Bluetooth
Clock settings
Set time
Set date
GPS time
Set time zone
Summertime
24-hour mode
E130532
78
Information Displays
Menu structure - information and
entertainment display
You can access the menu using the
Information and entertainment display
control. For item location: See At a
Glance (page 10).
79
Information Displays
Vehicles with navigation system
Navigation
Active guidance
Route sections list
Route
Block next section
Unblock rt sectn
Country
City/postcode
Destination input
Street
District
Start guidance
TA
TMC messages
Traffic
Block next section
Route sections list
Unblock rt sectn
Start guidance
Change address
Home address
Last destinations
Favourites
Favourites A-Z
Points of interest
POIs nearby
Near destination
Along motorway
POIs near address
Search by name
New tour
Stored tours
Tour planning
Store position
Route
Route options
Eco
Fast
Short
Driver
Always ask
Leisurely
Normal
Fast
A
B
C
E130534
80
Information Displays
A
B
C
Eco settings
Trailer
Roof box
Dynamic
Motorway
Tunnel
Ferry/motorail
Toll
Seasonal roads
Toll sticker
Special functions
GPS info
System info
Enter position
Demo mode
CD
See separate menu structure
Radio
See separate menu structure
Auxiliary
See separate menu structure
Phone
See separate menu structure
Menu
Navigation
Route options
Map display
B
C
E130535
81
Route
Driver
Eco Settings
Dynamic
Motorway
Tunnel
Ferry/motorail
Toll
Seasonal roads
Toll sticker
Map content
Arrows on map
Nav time display
Map heading up
Best contrast
Information Displays
B
C
Assistance options
Signs/lanes
Speed limits
Nav icons in lists
Personal data
Clear last destination
Clear favourites
Delete home address
Clear all
Reset all settings
Audio Settings
Clock Settings
See separate menu structure
See separate menu structure
E130536
Outside air temperature
TRIP COMPUTER
Shows the outside air temperature.
Trip Odometer
Odometer
Registers the mileage of individual
journeys.
Registers the total mileage of the vehicle.
Resetting the trip computer
Distance to empty
To reset a particular display:
Indicates the approximate distance the
vehicle will travel on the fuel remaining in
the tank. Changes in driving pattern may
cause the value to vary.
1.
Highlight Trip Computer with the up
and down arrow buttons and press the
right arrow button.
2. Highlight the function to be reset.
3. Hold the OK button pressed.
Instantaneous fuel consumption
Indicates the current average fuel
consumption.
PERSONALISED SETTINGS
Average fuel consumption
Language setting
Indicates the average fuel consumption
since the function was last reset.
A choice of eleven languages are available:
Average speed
English, German, Italian, French, Spanish,
Turkish, Russian, Dutch, Polish, Swedish
and Portuguese.
Indicates the average speed calculated
since the function was last reset.
82
Information Displays
Measure units
To toggle between metric and imperial
units, scroll to this display and press the
OK button.
Toggling the units of measure using this
display will affect the following displays:
• Distance to empty.
• Average fuel consumption.
• Instantaneous fuel consumption.
• Average speed.
Temperature units
E130248
To toggle between metric and imperial
units, scroll to this display and press the
OK button.
Press the OK button to acknowledge and
remove some messages from the
information display. Other messages will
be removed automatically after a short
time.
Toggling the temperature units using this
display will affect the following displays:
• Outside air temperature.
• The temperature display in the
automatic climate control.
Certain messages need to be confirmed
before you can access the menus.
Message indicator
Chime deactivation
The message indicator
illuminates to supplement some
messages. It will be red or amber
depending on the severity of the message
and will remain on until the cause of the
message has been rectified.
The following chimes can be deactivated:
• Warning messages.
• Information messages.
INFORMATION MESSAGES
Some messages will be supplemented by
a system specific symbol with a message
indicator.
Note: Certain messages may be
abbreviated or shortened depending upon
which cluster type you have.
83
Information Displays
Active City Stop
Message
Indicator
Active City Stop Sensor
blocked Clean screen
amber
Active City Stop not
available
amber
Active City Stop Auto
braking
-
Action
See Using Active City Stop (page 162).
See Using Active City Stop (page 162).
See Using Active City Stop (page 162).
Airbag
Message
Airbag malfunction
service now
Message
indicator
amber
Action
Have the system checked by a properly trained
technician as soon as possible.
Alarm
Message
Message
indicator
Alarm triggered check
vehicle
amber
Alarm malfunction
service required
-
Action
See Alarm (page 39).
Have the system checked by a properly trained
technician.
Automatic main beam control
Message
Indicator
Action
Front camera low visibility Clean screen
amber
The front camera sensor has reduced visibility.
Clean the windscreen.
Front camera malfunction Service required
amber
The front camera sensor has malfunctioned. Have
this checked as soon as possible.
84
Information Displays
Battery and charging system
Message
Electrical system over
voltage stop safely
Battery low check
handbook
Message
indicator
Action
red
Stop your vehicle as soon as it is safe to do so and
switch off the ignition. Have the system checked
by a properly trained technician as soon as
possible.
amber
Have the system checked by a properly trained
technician as soon as possible.
Blind spot monitor
Message
Message
indicator
BLIS low visibility check
handbook
amber
See Blind Spot Monitor (page 66).
BLIS: right sensor fault
service required
amber
Have the system checked by a properly trained
technician as soon as possible.
BLIS: left sensor fault
service required
amber
Have the system checked by a properly trained
technician as soon as possible.
BLIS not available
trailer attached
amber
See Blind Spot Monitor (page 66).
Action
Child power lock
Message
Message
indicator
Child lock malfunction
service required
amber
Action
Have the system checked by a properly trained
technician as soon as possible.
Climate control
Message
Indicator
Action
Auxiliary Heater on
amber
See Auxiliary Heater (page 102).
Auxiliary Heater off
-
See Auxiliary Heater (page 102).
85
Information Displays
Cruise control and Adaptive cruise control (ACC)
Message
Indicator
Action
Front radar sensor
blocked check handbook
amber
Forward Alert not available
amber
ACC not available
amber
See Adaptive cruise control (ACC) (page 148).
Message
indicator
Action
See Adaptive cruise control (ACC) (page 148).
See Adaptive cruise control (ACC) (page 148).
Doors open
Message
Driver door open
red
Stop the vehicle as soon as safely possible and
close.
Driver side rear door
open
red
Stop the vehicle as soon as safely possible and
close.
Passenger door open
red
Stop the vehicle as soon as safely possible and
close.
Passenger side rear
door open
red
Stop the vehicle as soon as safely possible and
close.
Luggage compartment
lid open
red
Stop the vehicle as soon as safely possible and
close.
Bonnet open
red
Stop the vehicle as soon as safely possible and
close. See Opening and Closing the Bonnet
(page 190).
Driver alert
Message
Indicator
Driver fatigue warning
Rest now
red
Driver fatigue warning
Rest suggested
amber
Action
Stop and rest as soon as it is safe to do so.
Take a rest break soon.
86
Information Displays
Engine immobiliser
Message
Message
indicator
Action
Immobiliser active
check handbook
amber
Your key has not been recognised. Remove the
key and try again.
Immobiliser malfunction service required
amber
Have the system checked by a properly trained
technician as soon as possible.
Hill start assist
Message
Hill start assist not
available
Message
indicator
amber
Action
Have the system checked by a properly trained
technician.
Keyless entry
Message
Ford KeyFree key not
inside car
Message
indicator
Action
red
See Keyless Entry (page 34).
Ford KeyFree key inside
vehicle
amber
See Keyless Entry (page 34).
Ford KeyFree Place key
in key holder
-
See Keyless Entry (page 34).
Ford KeyFree no key
detected
-
See Keyless Entry (page 34).
Key battery low replace
soon
-
See Changing the remote control battery (page
29).
Steering lock engaged
turn steering wheel
-
See Steering Wheel Lock (page 114).
87
Information Displays
Lane keeping aid
Message
Lane keeping aid
malfunction Service
required
Indicator
amber
Action
Have the system checked by a properly trained
technician as soon as possible.
Lighting
Message
Message
indicator
Headlamp malfunction
service required
amber
Action
Have the system checked by a properly trained
technician as soon as possible.
Brake lamp bulb fault
-
One or both of the brake lamp bulbs have blown.
Check the brake lamp bulbs. See Changing a
Bulb (page 55).
Park lamp bulb fault
-
One or both of the side or tail lamp bulbs have
blown. Check the side and tail lamp bulbs. See
Changing a Bulb (page 55).
Rear fog lamp bulb
fault
-
One or both of the rear fog lamp bulbs have blown.
Check the rear fog lamp bulbs. See Changing a
Bulb (page 55).
Dipped beam bulb fault
-
One or both of the headlamp dipped beam bulbs
have blown. Check the headlamp dipped beam
bulbs. See Changing a Bulb (page 55).
Trailer brake lamp bulb
fault
-
One or both of the brake lamp bulbs on your trailer
have blown. Check the brake lamp bulbs on your
trailer.
Trailer turn lamp bulb
fault
-
One or both of the direction indicator bulbs on
your trailer have blown. Check the direction indicator bulbs on your trailer.
88
Information Displays
Maintenance
Message
indicator
Action
High engine temperature stop safely
red
Stop your vehicle as soon as it is safe to do so and
switch off the ignition. Have the system checked
by a properly trained technician as soon as
possible.
Brake fluid level low
service now
red
Check the brake fluid level. See Brake and Clutch
Fluid Check (page 200).
Brake system malfunction stop safely
red
Stop the vehicle as soon as safely possible. Have
the system checked by a properly trained technician immediately.
Engine malfunction
service now
red
Stop the vehicle as soon as safely possible and
switch off the engine immediately. Have the
system checked by a properly trained technician
immediately.
Message
Water detected in fuel
service required
amber
Have the system checked by a properly trained
technician as soon as possible.
Engine malfunction
service now
amber
Have the system checked by a properly trained
technician as soon as possible.
Washer fluid level low
-
Check the washer fluid level. See Washer Fluid
Check (page 200).
Engine oil change due
-
Have the system checked by a properly trained
technician.
Occupant protection
Message
Service Beltminder
Indicator
-
Action
Have the system checked by a properly trained
technician as soon as possible.
Parking aid
Message
Indicator
Parking aid malfunction
Service required
amber
Action
Have the system checked by a properly trained
technician as soon as possible.
89
Information Displays
Parking brake
Message
Indicator
Action
Park brake applied
red
See Parking Brake (page 132).
Park brake applied
amber
See Parking Brake (page 132).
Power steering
Message
Message
indicator
Action
Steering lock malfunction stop safely
red
Stop your vehicle as soon as it is safe to do so and
switch off the ignition. Have the system checked
by a properly trained technician as soon as
possible.
red
Stop your vehicle as soon as it is safe to do so and
switch off the ignition. Have the system checked
by a properly trained technician as soon as
possible.
Steering loss stop
safely
Steering assist
malfunction service
required
amber
Power steering. Full steering will be maintained
but you will need to exert greater force on the
steering wheel. Have the system checked by a
properly trained technician as soon as possible.
Steering malfunction
service now
amber
Have the system checked by a properly trained
technician.
Stability control (ESP)
Message
Traction control off
Indicator
amber
Action
See General Information (page 75).
Starting the engine
Message
Ford KeyFree switch
ignition off press
POWER
Message
indicator
red
Action
See Keyless Starting (page 116).
90
Information Displays
Message
Message
indicator
Drive to clean exhaust
filter check handbook
amber
See Diesel Particulate Filter (page 118).
Engine malfunction
service now
amber
See Diesel Particulate Filter (page 118).
Press brake to start
-
See Keyless Starting (page 116).
Press clutch to start
-
See Keyless Starting (page 116).
Press brake and clutch
to start
-
See Keyless Starting (page 116).
Engine preheating
-
See Starting a Diesel Engine (page 116).
Cleaning exhaust filter
-
See Diesel Particulate Filter (page 118).
Filter cleaning
complete
-
See Diesel Particulate Filter (page 118).
Action
Start-stop
Message
Message
indicator
Action
Auto StartStop Switch
ignition off
red
Switch the ignition off before leaving the vehicle
if the system has shut down the engine. See Using
start-stop (page 120).
Auto StartStop
malfunction service
required
amber
Have the system checked by a properly trained
technician.
Auto StartStop Press
clutch to start engine
-
The engine needs to be restarted, press the clutch
pedal to start. See Using start-stop (page 120).
Auto StartStop Select
neutral
-
Select neutral for the system to restart the engine.
See Using start-stop (page 120).
Auto StartStop Manual
Start required
-
The system is not functioning. A manual restart is
required.
91
Information Displays
Transmission
Message
indicator
Action
Transmission too hot
press brake
red
Under certain driving conditions it is possible that
the clutches in the transmission can overheat. In
these circumstances it is necessary to press the
brake pedal and stop the vehicle to prevent further
overheating. Select N (NEUTRAL) or P (PARK)
and apply the foot brake and parking brake until
the transmission has cooled and the message
disappears from the display. If the vehicle is driven
with this message active you may experience
vehicle judder as a further overheat warning.
Transmission malfunction service now
red
Have the system checked by a properly trained
technician as soon as possible.
red
The transmission is too hot. In these extreme
conditions the transmission will disengage drive
in order to prevent damage due to overheating.
You will not be able to drive until the transmission
has cooled. Select N (NEUTRAL) or P (PARK)
and apply the foot brake and parking brake until
the transmission has cooled and the message
disappears from the display.
Transmission too hot
press brake
amber
Under certain driving conditions it is possible that
the clutches in the transmission can overheat. In
these circumstances it is necessary to press the
brake pedal and stop the vehicle to prevent further
overheating. Select N (NEUTRAL) or P (PARK)
and apply the foot brake and parking brake until
the transmission has cooled and the message
disappears from the display. If the vehicle is driven
with this message active you may experience
vehicle judder as a further overheat warning.
Transmission limited
function check handbook
amber
Some gears may not be available. Have the
system checked by a properly trained technician
as soon as possible.
-
At low outside temperatures, after starting the
engine, it may take the transmission several
seconds to engage R (REVERSE) or D (DRIVE).
Keep the brake pedal depressed until these
messages disappear from the display.
Message
Transmission overheating stop safely
Transmission warming
up please wait
92
Information Displays
Message
indicator
Action
Transmission not in
Park select P
-
See Automatic Transmission (page 129). See
Starting and Stopping the Engine (page 114).
To start press brake
-
See Automatic Transmission (page 129). See
Starting and Stopping the Engine (page 114).
Press brake pedal
-
See Automatic Transmission (page 129).
Message
Tyre pressure monitoring system
Message
Message
indicator
Action
Check tyre pressures
amber
The pressure in one or more tyres has dropped.
Check as soon as possible.
Tyre pressure sys
malfunction service
required
amber
Permanent malfunction. Have your vehicle
checked by a properly trained technician.
93
Climate Control
Warming the interior
PRINCIPLE OF OPERATION
Direct the air towards your feet. In cold or
humid weather conditions, direct some of
the air towards the windscreen and the
door windows.
Outside air
Keep the air intakes forward of the
windscreen free from obstruction (snow,
leaves etc.) to allow the climate control
system to function effectively.
Cooling the interior
Direct the air towards your face.
Recirculated air
AIR VENTS
CAUTION
Prolonged use of recirculated air may
cause the windows to mist up. If the
windows mist up, follow the settings
for defrosting and demisting the
windscreen.
Centre air vents
The air currently in the passenger
compartment will be recirculated. Outside
air will not enter the vehicle.
Heating
Heating performance depends on the
temperature of the engine coolant.
Air conditioning
Note: The air conditioning operates only
when the temperature is above 4°C (39°F).
Note: If you use the air conditioning, the
fuel consumption of your vehicle will be
higher.
E132995
Air is directed through the evaporator
where it is cooled. Humidity is extracted
from the air to help keep the windows free
of mist. The resulting condensation is
directed to the outside of the vehicle and
it is therefore normal if you see a small
pool of water under your vehicle.
General information on controlling
the interior climate
Fully close all the windows.
94
Climate Control
Side air vent
MANUAL CLIMATE CONTROL
Air distribution control
B
C
D
E132996
E
A
E74660
A
Face level
B
Face level and footwell
C
Footwell
D
Footwell and windscreen
E
Windscreen
You can set the air distribution control to
any position between the symbols.
95
Climate Control
Blower
Ventilation
A
E129885
Set the air distribution control, blower and
air vents to suit your requirements.
Air conditioning
Switching the air conditioning on and
off
E75470
A
Off
Note: If you switch the blower off, the
windscreen may mist up.
If you turn the blower off, the air
conditioning will turn off. When you turn
the blower on again, the air conditioning
will come on automatically.
Recirculated air
Cooling with outside air
E73059
Press the button to toggle between outside
air and recirculated air.
Heating the interior quickly
E129886
Cooling the interior quickly
E129884
E129887
96
Climate Control
With the heater control in this position, the
air conditioning and recirculated air will
switch on automatically.
If you move the air distribution control to
a position other than windscreen, the A/C
will remain on.
You can switch the air conditioning and
recirculated air on and off.
You can switch the air conditioning and
recirculated air on and off while the air
distribution control is set to windscreen
Defrosting and demisting the
windscreen
If necessary, switch the heated windows
on. See Heated Windows and Mirrors
(page 100).
Reducing interior air humidity
E129888
When the temperature is above 4°C
(39°F), the air conditioning will switch on
automatically. Make sure that the blower
is on. The indicator in the switch will
illuminate during defrosting and demisting.
E129889
AUTOMATIC CLIMATE CONTROL
E133114
The system in your vehicle is dual-zone
automatic climate control. When the
system is in mono mode, all the
temperature zones are linked to the driver's
zone. When you switch mono mode off,
the dual-zone system allows you to set
different temperatures for the driver's and
front passenger's side.
The system controls the temperature,
amount and distribution of the air flow
automatically and adjusts them according
to the driving and weather conditions.
Pressing the AUTO button once switches
on the auto mode.
97
Climate Control
To switch mono mode off
Note: Avoid adjusting the settings when
the vehicle interior is extremely hot or cold.
The automatic climate control adjusts to
the current circumstances automatically.
For the system to function properly, the side
and centre vents should be fully open.
Select a temperature for the passenger’s
side with the rotary control on the
passenger’s side. Mono mode will switch
off and MONO disappears from the
display. The temperature for the driver’s
side will remain unchanged. You can now
adjust the driver and passenger side
temperatures independently of each
another. The temperature settings for each
side are shown in the display. You can set
a temperature difference of up to 4°C
(8°F).
Note: The sunload sensor is located on top
of the instrument panel. Do not cover the
sensor with any objects.
Note: At low outside temperatures, when
the system is in auto mode, the air stream
will be directed to the windscreen and the
side windows as long as the engine is cold.
Note: If you set a temperature difference
of greater than 4°C (8°F), the temperature
on the other side will be adjusted so that
the difference remains 4°C (8°F).
Setting the temperature
Note: If you set one of the sides to HI or LO,
both sides will be set to HI or LO.
To switch mono mode back on
E133120
To switch mono mode back on, press and
hold the AUTO button. MONO reappears
in the display and the passenger’s side
temperature will be adjusted to the driver’s
side temperature.
E133115
You can set the temperature between
15.5°C (60°F) and 29.5°C (85°F) in steps
of 0.5°C (1°F). In position LO, 15°C (59°F),
the system will switch to permanent
cooling. In position HI, 30°C (86°F), the
system will switch to permanent heating.
Blower
Note: If either position LO or HI is selected,
the system will not regulate a stable
temperature.
Use the buttons to adjust the blower
speed.
Mono mode
The blower setting is indicated in the
display.
In mono mode, the temperature settings
for both the driver’s and passenger’s side
are linked. If you adjust the temperature
using the rotary control on the driver’s side,
the settings will be adjusted to the same
setting on the passenger’s side. In mono
mode, MONO appears in the display.
To return to auto mode, press the AUTO
button.
98
Climate Control
Air distribution
The blower speed and the temperature
control operate automatically and cannot
be adjusted manually. The blower is set to
high speed and the temperature to HI.
To adjust air distribution, press the desired
button. Any combination of settings can
be selected simultaneously.
A
B
When you select windscreen defrosting
and demisting, the heated screens switch
on automatically and switch off after a
short time.
To return to auto mode, press the AUTO
button.
C
Switching the air conditioning on
and off
E70308
A
Footwell
B
Face level
C
Windscreen
E91393
Press the A/C button to switch the air
conditioning on and off. A/C OFF appears
in the display when the air conditioning is
switched off.
When you select windscreen defrosting
and demisting, A, B and C switch off
automatically and the air conditioning
switches on. Outside air will flow into the
vehicle. You cannot select recirculated air.
A/C ON appears in the display when the
air conditioning is switched on.
Cooling the interior quickly
Recirculated air
Press the recirculated air button to toggle
between outside air and recirculated air.
E133122
Note: When the system is in auto mode and
the interior and exterior temperatures are
quite hot, the system selects recirculated
air automatically to maximise cooling of the
interior. Once the selected temperature is
reached, the system will reselect outside air
automatically.
Windscreen defrosting and
demisting
E91392
Press the windscreen defrosting and
demisting button. Outside air will flow into
the vehicle. Air conditioning is
automatically selected. As long as the air
distribution is set to this position, you
cannot select recirculated air.
Switching off the automatic
climate control
E133093
Press the button.
99
Climate Control
When switched off, the heating, ventilation
and air conditioning system is switched off
and recirculated air is selected.
ELECTRIC SUNROOF
WARNING
Before operating the electric sunroof
you should verify it is free of
obstructions and ensure that children
and/or pets are not in the proximity of the
sunroof opening. Failure to do so could
result in serious personal injury. It is the
primary responsibility of the supervising
adults to never leave a child unattended
in a vehicle and to never leave the keys in
an unattended vehicle.
HEATED WINDOWS AND
MIRRORS
Heated windows
Use the heated windows to defrost or
demist the windscreen or rear window.
Note: The heated windows operate only
when the engine is running.
Heated windscreen
Note: When the switches are operated
often during a short period of time, the
system might become inoperable for a
certain time to prevent damage due to
overheating.
E72506
Heated rear window
Note: The electric sunroof can also be
operated with the ignition off via the global
opening and global closing function. See
Global Opening and Closing (page 36).
E72507
There are two ways of opening the sunroof
– the rear of the sunroof lifts open or the
sunroof opens from the front, sliding back
under the roof. The sunroof opens and
closes whilst the switch is pressed.
Vehicles without auxiliary heater
If the ambient temperature is below 5°C
(41°F) and the engine coolant is below
65°C (149°F), the heated windscreen and
heated rear window will switch on
automatically. They will switch off
automatically.
Switch on the ignition to operate the
electric sunroof.
The power sunroof is operated by a switch
located between the sun visors.
Heated exterior mirrors
Electric exterior mirrors are fitted with a
heating element that will defrost or demist
the mirror glass. They will switch on
automatically when you switch the heated
rear window on.
100
Climate Control
Opening and closing the sunroof
To open or close the sunroof automatically
press either side of the switch to the
second action point and release it
completely. Press again to stop.
When the closed position is reached, the
sunroof stops automatically.
Sunroof anti-trap protection
WARNINGS
The anti-trap function is deactivated
until the memory has been reset.
Careless closing of the window can
cause injuries.
Careless closing of the electric
sunroof can override the anti-trap
protection and cause injuries.
E72188
Tilting the sunroof
The sunroof will stop automatically while
closing and reverse some distance if there
is an obstacle in the way.
To override anti-trap protection when there
is a resistance, e. g. in the winter, proceed
as follows:
WARNING
While the sunroof is being closed for
the third time, the anti-trap function
is disabled. Make sure there are no
obstacles in the way of the closing sunroof.
Close the sunroof a third time to the
resistance. The anti-trap function is
disabled and the sunroof cannot be closed
automatically. The sunroof will override
the resistance and can then be closed fully.
E72189
Opening and closing the sunroof
automatically
Note: When opening automatically, the
sunroof will stop about 8 cm from the fully
opened position. This position reduces the
buffeting noise which is sometimes heard
when the sunroof is fully open. The sunroof
will only stop automatically in this position
when the sunroof is opened automatically.
If the sunroof does not close after the third
attempt, have it checked by an expert.
101
Climate Control
Sunroof safety mode
AUXILIARY HEATER
WARNING
Parking heater
The anti-trap function is not active
during this procedure. Make sure that
there are no obstacles in the way of
the closing sunroof.
WARNINGS
The parking heater must not be
operated at filling stations, near
sources of combustible vapours or
dust or in enclosed spaces.
If the system detects a malfunction, it
enters a safety mode. The sunroof will
move for only about 0.5 seconds at a time
and then stop again. Close the sunroof by
pressing the button again when the
sunroof stops moving. When the rear of
the sunroof is lifted, lift the rear all the way
and then close the sunroof. Have the
system checked by an expert immediately.
The parking heater should be
switched on for approximately 10
minutes at least once a month all
year round. This prevents the water pump
and heater motor from seizing.
Note: The parking heater will only operate
if there is at least 7.5 litres (1.6 gallons) of
fuel in the fuel tank and the ambient
temperature is below 15°C (59°F). The
heater will not operate if the battery is low.
Sunroof relearning
WARNING
The anti-trap function is not active
during this procedure. Make sure that
there are no obstacles in the way of
the closing sunroof.
Note: The heating depends on the outside
air temperature.
In case the sunroof no longer closes
properly, follow this relearning procedure:
Note: On vehicles with manual climate
control the heating of the vehicle interior is
dependent on the temperature, air
distribution and blower control settings.
•
•
•
Note: When the parking heater is activated,
exhaust fumes may come from under the
sides of the vehicle. This is normal.
Tilt the rear of the sunroof as far as
possible. Release the button.
Press and hold the same button again
for 30 seconds until you see the
sunroof move.
Release the button and immediately
press and hold it again. The sunroof
will close, open fully and then close
again. Do not release the button before
the sunroof has reached the closed
position for the second time.
The parking heater operates independently
of the vehicle heater by heating the
engine’s coolant circuit. It is fed from the
vehicle fuel tank. You can also use it while
the vehicle is in motion to help the vehicle
heater warm up the interior more quickly.
Used properly, the parking heater provides
the following benefits:
If the button is not pressed continuously,
the relearning function will be interrupted.
Start the procedure once more from the
beginning.
102
Climate Control
•
•
•
It preheats the interior of the vehicle.
It keeps the windows clear of ice in the
event of frost and prevents
condensation.
It avoids cold starts and allows the
engine to reach operating temperature
sooner.
Park Heater
Program 1
Program 2
Once
Heat now
To prevent the battery from discharging:
•
•
Once the parking heater has performed
one heating cycle, the next
programmed heating cycle will only be
carried out if you have started the
vehicle’s engine in between.
After a heating cycle, drive the vehicle
for at least the period of the heating
cycle.
E136301
•
Programming the parking heater
Note: The programmed time is the time at
which you wish the vehicle to be warm and
ready to drive, not the time at which the
heater switches on.
•
The two time functions allow you to
programme up to two heating cycles
for each day of the week. These times
will remain stored and the heater will
warm up the vehicle at these times on
these days every week.
The function once allows you to
programme one heating cycle for one
specific day.
The function Heat now automatically
switches on the heater.
Note: You must programme the times at
least 70 minutes in advance of the time you
wish to set.
•
Note: You must set the time and date
correctly. See Clock (page 111).
Programming the functions Program 1
and Program 2
To programme the heating times:
1.
Use the arrow buttons on the steering
wheel to enter the main menu. See
Information Displays (page 75).
2. Select the park heater option.
Program 1
[07:55]
Monday
Tuesday
Wednesday
Thursday
Friday
E74468
103
Climate Control
1.
2.
3.
4.
5.
6.
7.
Fuel operated heater (depending
on country)
Use the arrow buttons on the steering
wheel to enter the main menu.
Select the first programme time list.
Highlight the day on which the heater
should warm up the vehicle.
Press the OK button.
Continue in the same way to select all
the days on which the heater should
warm up the vehicle.
To set the time at which the vehicle
should be warmed up, highlight the
time at the top of the display and press
the OK button. The hours start to flash.
Adjust the hours and minutes as
necessary.
WARNING
The fuel operated heater must not
be operated at filling stations, near
sources of combustible vapours or
dust or in enclosed spaces.
The fuel operated heater aids in warming
the engine and the vehicle interior on
vehicles with a diesel engine. It is switched
on or off automatically depending on the
outside air temperature and the coolant
temperature, unless you have deactivated
it.
To deactivate the fuel operated heater:
You can use the second programme time
list to set a second cycle, for example
different times on different days or twice
on the same day. The programming
procedure is the same as for the first
programme timer..
1.
Highlight Aux. Heater and press the
OK button. A cross appears in the box
when the heater is activated.
Diesel auxiliary heater (depending
on country)
Deactivating the programmed heater
The diesel auxiliary heater (PTC electrical
heater) aids in warming the engine and the
vehicle interior on vehicles with a diesel
engine. It is switched on or off
automatically depending on the outside
air temperature, the coolant temperature
and the alternator load.
1.
Use the arrow buttons on the steering
wheel to enter the main menu.
2. Uncheck the active program session.
Programming the heater for a single
cycle
1.
Select Once and press the right arrow
button.
2. Press the OK button and set the
required time and date.
3. Press OK to confirm the set time and
date.
Activating the heater manually
Highlight Heat now and press the OK
button. A cross appears in the box when
the heater is activated.
To deactivate the heater, uncheck the
Heat now function.
104
Seats
•
SITTING IN THE CORRECT
POSITION
•
bend your legs slightly so that you can
press the pedals fully.
position the shoulder strap of the seat
belt over the centre of your shoulder
and position the lap strap tightly across
your hips.
Make sure that your driving position is
comfortable and that you can maintain full
control of your vehicle.
MANUAL SEATS
Moving the seats backwards and
forwards
E68595
WARNINGS
Do not adjust the seats when the
vehicle is moving.
Only when you use the seat belt
properly, can it hold you in a position
that allows the airbag to achieve its
optimum effect.
When you use them properly, the seat,
head restraint, seat belt and airbags will
provide optimum protection in the event
of a collision. We recommend that you:
•
•
•
•
•
sit in an upright position with the base
of your spine as far back as possible.
do not recline the seatback more than
30 degrees.
adjust the head restraint so that the
top of it is level with the top of your
head and as far forwards as possible,
remaining comfortable.
keep sufficient distance between
yourself and the steering wheel. We
recommend a minimum of 250
millimetres (10 inches) between your
breastbone and the airbag cover.
hold the steering wheel with your arms
slightly bent.
E130249
WARNING
Rock the seat backwards and
forwards after releasing the lever to
make sure that it is fully engaged in
its catch.
105
Seats
Adjusting the lumbar support
Adjusting the angle of the
seatback
E78058
E130250
Adjusting the height of the driver’s
seat
HEAD RESTRAINTS
Adjusting the head restraint
WARNINGS
Raise the rear head restraint when
the rear seat is occupied by a
passenger.
When using a forward facing child
restraint on a rear seat, always
remove the head restraint from that
seat.
E70730
E66539
106
Seats
E135437
E135401
Adjust the head restraint so that the top
of it is level with the top of your head.
Removing the head restraint
Press the locking buttons and remove the
head restraint.
107
Seats
POWER SEATS
E78060
108
Seats
REAR SEATS
WARNINGS
When folding the seatbacks down,
take care not to get your fingers
caught between the seatback and
seat frame.
3
Make sure that the seats and the
seatbacks are secure and fully
engaged in their catches.
E135628
Folding the rear seatbacks
forwards
CAUTION
Lower the head restraints. See Head
Restraints (page 106).
Note: Make sure that the seat belt is fully
tightened into the retractor.
3. Place the seat belts in the clips on the
outboard trim.
1
1
Folding the seat cushions and the
rear seatbacks forwards
WARNING
Make sure the red indicator is not
showing when you engage the seat
in the catches.
2
CAUTIONS
Lower the head restraints. See Head
Restraints (page 106).
E135629
1. Press and hold the unlock buttons.
2. Push the seatback forwards.
When inserting your fingers between
the seat cushion and seatback, take
care not to get your fingers caught on
the ISOFIX anchor points and bracket. See
ISOFIX Anchor Points (page 21).
109
Seats
Folding the seatbacks up
2
WARNING
2
1
When folding the seatbacks up,
make sure that the belts are visible
to an occupant and not caught
behind the seat.
3
HEATED SEATS
CAUTION
Operating this function with the
engine off will drain the battery.
E135646
Note: Hold the cushion edge to avoid the
ISOFIX anchor points and brackets.
1.
Insert your fingers between the seat
cushion and seatback and fold the seat
cushion forwards.
2. Press and hold the unlock buttons.
3. Push the seatback forwards.
E130471
4
The maximum temperature is reached
after five or six minutes. It is regulated
thermostatically.
The seat heating will operate only when
the ignition is on.
E135647
Note: Make sure that the seat belt is fully
tightened into the retractor.
4. Place the seat belts in the clips on the
outboard trim.
110
Convenience features
INSTRUMENT LIGHTING
DIMMER
E132415
Press the element in to use the cigar
lighter. It will pop out automatically.
E132712
AUXILIARY POWER POINTS
Press repeatedly or press and hold until
the desired level is reached.
CAUTION
Note: If the battery is disconnected,
discharged, or a new battery is installed, the
dimmer will set the illuminated components
to the maximum setting automatically.
If you use the socket when the engine
is not running, the battery may
discharge.
CLOCK
Note: You can use the socket to power 12
volt appliances that have a maximum
current rating of 10 Amperes. Use only Ford
accessory connectors or connectors
specified for use with SAE standard sockets.
See Information Displays (page 75).
CIGAR LIGHTER
CAUTIONS
If you use the socket when the engine
is not running, the battery may
discharge.
Do not hold the cigar lighter element
pressed in.
E78056
Auxiliary power sockets are located in the
centre console and in the luggage
compartment.
Note: You can use the socket to power 12
volt appliances that have a maximum
current rating of 10 Amperes. Use only Ford
accessory connectors or connectors
specified for use with SAE standard sockets.
111
Convenience features
CUP HOLDERS
WARNING
Do not place hot drinks in the cup
holders when the vehicle is moving.
Rear seat armrest
E91508
CHILDMINDER MIRROR
E132505
GLASSES HOLDER
E75192
E75193
112
Convenience features
SATELLITE NAVIGATION UNIT
HOLDER
AUXILIARY INPUT (AUX IN)
SOCKET
Adjusting the holder
1
3
2
E132422
See Auxiliary input (AUX IN) socket
(page 243).
USB PORT
E112711
1. Unlock.
2. Adjust the holder to the desired
position.
3. Lock.
Note: Make sure that the navigation unit
holder is locked in position.
FLOOR MATS
WARNING
When using the floor mats, always
make sure the floor mat is properly
secured using the appropriate fixings
and positioned so that it does not interfere
with the operation of the pedals.
E132423
See Connectivity (page 265).
113
Starting and Stopping the Engine
II The ignition is switched on. All electrical
circuits are operational. Warning lamps
and indicators illuminate. This is the key
position when driving. You must also select
it when being towed.
GENERAL INFORMATION
General points on starting
If the battery has been disconnected the
vehicle may exhibit some unusual driving
characteristics for approx. 8 kilometres (5
miles) after reconnecting the battery.
III The starter motor is activated. Release
the key as soon as the engine starts.
This is because the engine management
system must realign itself with the engine.
Any unusual driving characteristics during
this period may be disregarded.
STEERING WHEEL LOCK
WARNING
Always check that the steering is
unlocked before attempting to move
your vehicle.
Starting the engine by towing or
pushing
WARNING
Vehicles without keyless starting
To prevent damage you must not
push or tow start your vehicle. Use
booster cables and a booster battery.
See Jump-Starting the Vehicle (page
206).
To activate the steering wheel lock;
1.
Remove the key from the ignition
switch.
2. Turn the steering wheel.
IGNITION SWITCH
Vehicles with keyless starting
Note: The steering wheel lock will not
activate when the ignition is on or the
vehicle is moving.
WARNING
Never return the key to position 0 or
I when the vehicle is in motion.
Your vehicle has an electronically
controlled steering wheel lock. This
operates automatically.
The steering wheel lock will activate after
a short period of time once you have
parked your vehicle and the passive key is
outside of the vehicle, or when you lock the
vehicle. See Keyless Entry (page 34).
Deactivating the steering wheel lock
E72128
Switch the ignition on, or:
0 The ignition is off.
Vehicles with automatic transmission
• Press the brake pedal.
I The ignition and all main electrical circuits
are disabled.
Vehicles with manual transmission
• Press the clutch pedal.
Note: Do not leave the ignition key in this
position for too long to avoid discharging
the battery.
114
Starting and Stopping the Engine
STARTING A PETROL ENGINE
Flooded engine
Note: You can only operate the starter for
a maximum of 30 seconds at a time.
Vehicles with manual transmission
1. Fully depress the clutch pedal.
2. Fully depress the accelerator pedal and
hold it there.
3. Start the engine.
Cold or hot engine
All vehicles
CAUTION
Vehicles with automatic transmission
When the temperature is below -20°C
(-4°F), switch the ignition on for at
least one second before starting the
engine. This will make sure that the
maximum fuel pressure is established for
starting the engine.
1. Select park or neutral.
2. Fully depress the accelerator pedal and
hold it there.
3. Fully depress the brake pedal.
4. Start the engine.
Vehicles with manual transmission
All vehicles
Note: Do not touch the accelerator pedal.
If the engine does not start, repeat the
Cold or hot engine procedure.
1. Fully depress the clutch pedal.
2. Start the engine.
Engine idle speed after starting
The speed at which the engine idles
immediately after starting will vary
depending on the engine temperature.
Vehicles with automatic transmission
Note: Do not touch the accelerator pedal.
1. Select park or neutral.
2. Fully depress the brake pedal.
3. Start the engine.
If the engine is cold then the idle speed will
automatically be increased in order to heat
the catalytic converter as quickly as
possible. This makes sure that vehicle
emissions are kept to an absolute
minimum.
All vehicles
If the engine does not start within 15
seconds, wait for a short period and try
again.
The idle speed will slowly decrease to the
normal level as the catalytic converter
warms up.
If the engine does not start after three
attempts, wait 10 seconds and follow the
Flooded engine procedure.
STARTING A PETROL ENGINE
- E85
If you have difficulty starting the engine
when the temperature is below -25°C
(-13°F), press the accelerator pedal
between ¼ to ½ of its travel and try again.
For general information on starting a petrol
engine. See Starting a Petrol Engine
(page 115).
115
Starting and Stopping the Engine
Starting at low ambient
temperatures
If the battery has been disconnected or
after the fuel type has been changed, the
idle speed may be irregular. This will
improve after 10 to 30 seconds.
When the temperature is lower than -10°C
(14°F) and the vehicle is filled with E85, an
engine block heater should be used to
facilitate starting. See Engine Block
Heater (page 119). Failure to do this will
result in a non start.
STARTING A DIESEL ENGINE
Cold or hot engine
If the temperature is expected to remain
below -10°C (14°F), it is recommended
that you increase the proportion of petrol
in the tank by topping up with 95 octane
unleaded petrol if the tank is not already
full. About 10 litres (2.2 gallons) of petrol
will reduce the proportion of E85 in a ¾ full
tank from 85% to 70% and will
considerably improve cold start capability.
All vehicles
Note: When the temperature is below -15°C
(5°F), you may need to crank the engine for
up to 25 seconds.
Note: Continue cranking the engine until it
starts.
Note: You can only operate the starter for
a maximum of 30 seconds at a time.
If, at very low temperatures, the tank is
filled with only E85 and there is no way to
use an engine block heater, you may
experience difficulties starting the engine.
Switch the ignition on and wait
until the glow plug indicator goes
off.
If the engine fails to start, proceed as
follows:
Vehicles with manual transmission
Note: Do not touch the accelerator pedal.
1. Fully depress the accelerator pedal.
2. Turn the ignition key to position III.
1. Fully depress the clutch pedal.
2. Start the engine.
CAUTION
Release the ignition key as soon as
the engine has started.
Vehicles with automatic transmission
1. Select park or neutral.
2. Fully depress the brake pedal.
3. Start the engine.
3. Gradually release the accelerator pedal
after five seconds of engine cranking
or as the engine speed rises.
If the engine fails to start, repeat steps 1, 2
and 3, or connect an engine block heater
for two hours before attempting another
start.
KEYLESS STARTING
WARNINGS
The keyless starting system may not
function if the key is close to metal
objects or electronic devices such as
mobile phones.
During starting, the fuel injectors are turned
off as long as the accelerator pedal is
depressed. This can be used to drain
excessive fuel from the intake manifold
after several unsuccessful starting
attempts.
116
Starting and Stopping the Engine
Starting with manual transmission
WARNINGS
Always check that the steering wheel
lock is deactivated before
attempting to move your vehicle.
See Steering Wheel Lock (page 114).
Note: Releasing the clutch pedal during
engine start will stop the engine cranking
and return to ignition on.
1. Fully depress the clutch pedal.
2. Press the start button.
Note: The ignition may automatically
switch off after a period of time if your
vehicle has been left unattended with the
ignition on. This is to prevent the vehicle
battery from discharging.
Starting a diesel engine
Note: Engine cranking may not commence
until the engine glow plug cycle has been
completed. This may take several seconds
in extremely cold conditions.
Note: A valid passive key must be located
inside the vehicle to switch the ignition on
and start the engine.
Note: Continue to press the clutch or brake
pedal until engine cranking begins.
Note: To start your engine you must also
fully depress the brake or clutch pedal,
depending on the transmission fitted.
Failure to start
The passive starting system will not
function if:
• The passive key frequencies are
jammed.
• The passive key battery is flat.
If you are unable to start your vehicle carry
out the following procedure.
E85766
Ignition on
Press the start button once. All electrical
circuits are operational, warning lamps and
indicators illuminate.
Starting with automatic
transmission
Note: Releasing the brake pedal during
engine start may stop the engine cranking
and return to ignition on.
1.
Make sure the transmission is in P or
N.
2. Fully depress the brake pedal.
3. Press the start button.
E87381
1.
117
Carefully prise out the cover.
Starting and Stopping the Engine
Press and hold the start button for two
seconds, or press twice within two
seconds.
DIESEL PARTICULATE FILTER
The DPF forms part of the emissions
reduction systems fitted to your vehicle. It
filters harmful diesel particulates (soot)
from the exhaust gas.
Regeneration
WARNING
E85767
Do not park or idle your vehicle over
dry leaves, dry grass or other
combustible materials. The DPF
regeneration process creates very high
exhaust gas temperatures and the exhaust
will radiate a considerable amount of heat
during and after DPF regeneration, and
after you have switched the engine off.
This is a potential fire hazard.
2. Insert the key into the key holder.
3. With the key in this position you can
use the start button to switch the
ignition on and start your vehicle.
Stopping the engine with the
vehicle stationary
Note: The ignition, all electrical circuits,
warning lamps and indicators will be
switched off.
CAUTION
Avoid running out of fuel.
Manual transmission
Press the start button.
Note: During regeneration at low speed or
engine idle, you may smell a hot metallic
odour and could notice a clicking metallic
sound. This is due to the high temperatures
reached during regeneration and is normal.
Automatic transmission
1. Move the selector lever to position P.
2. Press the start button.
Stopping the engine when the
vehicle is moving
Note: After you have switched your engine
off the fans may continue to run for a short
period of time.
WARNING
Unlike a normal filter which requires
periodic replacement, the DPF has been
designed to regenerate, or clean itself to
maintain operating efficiency. The
regeneration process takes place
automatically. However, some driving
conditions mean that you may need to
support the regeneration process.
Switching off the engine when the
vehicle is still moving will result in a
loss of brake and steering assistance.
The steering will not be locked, but higher
effort will be required. When the ignition is
switched off some electrical circuits,
warning lamps and indicators may also be
OFF.
118
Starting and Stopping the Engine
If you drive only short distances or your
journeys contain frequent stopping and
starting, where there is increased
acceleration and deceleration, occasional
trips with the following conditions will
assist the regeneration process:
•
•
•
•
Drive your vehicle at a constant speed,
preferably on a main road or motorway,
for up to 20 minutes.
Avoid prolonged idling and always
observe speed limits and road
conditions.
Do not switch off the ignition.
Use a lower gear than normal to
maintain a higher engine speed during
this journey, where appropriate.
E135813
Connect the engine heater for two to three
hours before starting the engine.
SWITCHING OFF THE ENGINE
Vehicles with a turbocharger
CAUTION
Do not switch the engine off when it
is running at high speed. If you do, the
turbocharger will continue running
after the engine oil pressure has dropped
to zero. This will lead to premature
turbocharger bearing wear.
Release the accelerator pedal. Wait until
the engine has reached idle speed and then
switch it off.
ENGINE BLOCK HEATER
CAUTION
Make sure you disconnect the power
cable from the engine heater
connector before driving away.
Note: The engine heater connector is
located in the front bumper.
119
Start-Stop
Note: If you stall the engine, and then
depress the clutch pedal within a couple of
seconds, the system will automatically
restart the engine.
PRINCIPLE OF OPERATION
CAUTION
For vehicles with Start-stop the
battery requirement is different. It
must be replaced by one of exactly
the same specification as the original.
Note: The Start-stop indicator will
illuminate green when the engine shuts
down. See Warning Lamps and Indicators
(page 71).
Note: The Start-stop indicator will flash
amber, requiring you to select neutral or
depress the clutch pedal. In conjunction a
message will be shown in the display.
The system reduces fuel consumption and
CO2 emissions by shutting down the
engine when the vehicle is idling, for
example at traffic lights. The engine will
automatically restart when the driver
presses the clutch pedal or when required
by a vehicle system, for example to
recharge the battery.
Note: If the system detects a malfunction,
it is deactivated. Have the system checked
by a properly trained technician.
Note: If you have switched the system off,
the switch will be illuminated.
To obtain maximum benefit from the
system, move the gear lever to the neutral
position and release the clutch pedal
during any stop of longer than three
seconds.
Note: The system is on by default. To
switch the system off, press the switch in
the instrument panel. The system will only
be de-activated for the current ignition
cycle. To turn it on, press the switch again.
For item location. See At a Glance (page
10).
USING START-STOP
WARNINGS
The engine may restart
automatically if required by the
system. See Principle of Operation
(page 120).
To stop the engine
Switch the ignition off before
opening the bonnet or carrying out
any maintenance.
1. Stop the vehicle.
2. Move the gear lever to the neutral
position.
3. Release the clutch pedal.
4. Release the accelerator pedal.
Always switch the ignition off before
leaving your vehicle, as the system
may have shut down the engine but
the ignition will still be live.
The system may not shut down the engine
under certain conditions, for example:
Note: The system only operates when the
engine is warm and the outside temperature
is between 0°C (32°F) and 30°C (86°F).
•
•
•
•
120
To maintain the interior climate.
Low battery voltage.
The outside temperature is too low or
too high.
The driver's door has been opened.
Start-Stop
•
•
•
Low engine operating temperature.
Low brake system vacuum.
If a road speed of 5 km/h (3 mph) has
not been exceeded.
To re-start the engine
Note: The gear lever must be in the neutral
position.
Depress the clutch pedal.
The system may automatically restart the
engine under certain conditions, for
example:
•
•
Low battery voltage.
To maintain the interior climate.
121
Eco Mode
Anticipation
PRINCIPLE OF OPERATION
Adjusting your vehicle speed and the
distance to other vehicles without the need
for heavy braking or acceleration will
improve fuel consumption.
The system assists the driver to drive more
efficiently by constantly monitoring
characteristics of gear changing,
anticipation of traffic conditions and
speeds on motorways and open roads.
Efficient speed
Note: These efficiency values do not result
in a defined fuel consumption figure. It might
vary as it is not only related to these driving
disciplines but also influenced by many
other factors such as short journeys and cold
starts.
Higher speeds use more fuel. Reducing
your cruising speed on open roads will
improve fuel consumption.
Type 2 and 3
The relevant information will be shown in
the display.
Note: Frequent short journeys, where the
engine does not fully warm up, will also
increase fuel consumption.
USING ECO MODE
The value of these characteristics is
represented by petals shown in the display,
with five petals being the most efficient.
The more efficiently you drive, the better
the rating, and the better your overall fuel
consumption.
The system is accessed using the relevant
information display menu. See
Information Displays (page 75).
Resetting Eco mode
Type 1
Reset the average fuel consumption.
Note: New values may take a short time to
calculate.
E121813
A
B
A
Gear shifting
B
Anticipation
C
Efficient speed
C
Gear shifting
Using the highest drivable gear appropriate
for the road conditions will improve fuel
consumption.
122
Fuel and Refuelling
SAFETY PRECAUTIONS
CAUTIONS
Do not use leaded petrol or petrol with
additives containing other metallic
compounds (e.g. manganese-based).
They could damage the emission system.
WARNINGS
Stop refuelling after the fuel nozzle
stops the second time. Additional
fuel will fill the expansion space in
the fuel tank which could lead to fuel
overflowing. Fuel spillage could be
hazardous to other road users.
Do not use methanol instead of E85.
Note: We recommend that you use only
high quality fuel without additives or other
engine treatments.
Do not use any kind of flames or heat
near the fuel system. The fuel system
is under pressure. There is a risk of
injury if the fuel system is leaking.
Note: When using E85, you may experience
a higher fuel consumption.
CAUTION
Note: Your vehicle will operate well on
commercial quality 95 octane unleaded
petrol, but only high quality E85 offers the
same protection and performance.
Do not use leaded petrol or petrol with
additives containing other metallic
compounds (e.g. manganese-based).
They could damage the emission system.
Use minimum 95 octane unleaded
petrol that meets the specification defined
by EN 228, or equivalent. You can also use
a mixture of unleaded petrol and E85.
Note: We recommend that you use only
high quality fuel without additives or other
engine treatments.
Long-term storage
FUEL QUALITY - PETROL
Use minimum 95 octane unleaded
petrol that meets the specification defined
by EN 228, or equivalent.
Due to small amounts of corrosive
impurities that may be found in the E85, it
is recommended that you fill the tank with
only 95 octane unleaded petrol prior to
long-term storage of your vehicle.
FUEL QUALITY - E85
FUEL QUALITY - DIESEL
WARNING
WARNINGS
Do not modify the fuel system
configuration or the components in
the system.
Do not mix diesel with oil, petrol or
other liquids. This could cause a
chemical reaction.
Do not replace the fuel system or the
components with parts not specially
designed to be used with E85.
CAUTIONS
Do not add kerosene, paraffin or
petrol to diesel. This could cause
damage to the fuel system.
123
Fuel and Refuelling
CAUTIONS
Use diesel that meets the
specification defined by EN 590, or
the relevant national specification.
CAUTIONS
Do not push-start or tow-start your
vehicle. Use booster cables. See
Jump-Starting the Vehicle (page
206).
Note: We recommend that you use only
high quality fuel.
Do not switch the ignition off when
driving.
Note: The use of additives or other engine
treatments not approved by Ford is not
recommended.
FUEL FILLER FLAP
Note: We do not recommend the prolonged
use of additives intended to prevent fuel
waxing.
WARNINGS
Take care when refuelling to avoid
spilling any residual fuel from the fuel
nozzle.
Long-term storage
Do not use any kind of flames or heat
near the fuel system. The fuel system
is under pressure. There is a risk of
injury if the fuel system is leaking.
Most diesel fuels contain bio-diesel, it is
recommended to fill the tank with purely
mineral diesel (where available) or add an
anti-oxidant prior to long-term storage of
your vehicle exceeding two months. Your
dealer can help you with a suitable
anti-oxidant.
CAUTION
If you use a high pressure spray to
wash your vehicle, only spray the fuel
filler flap briefly from a distance not
less than 200 millimetres (8 inches).
CATALYTIC CONVERTER
WARNING
Type 1
Do not park or idle your vehicle over
dry leaves, dry grass or other
combustible materials. The exhaust
will radiate a considerable amount of heat
during use, and after you have switched
the engine off. This is a potential fire
hazard.
Driving with a catalytic converter
CAUTIONS
Avoid running out of fuel.
Do not crank the engine for long
periods.
E135934
Do not run the engine when a spark
plug lead is disconnected.
124
Fuel and Refuelling
2. Insert the fuel nozzle up to and
including the first notch on the nozzle
A. Keep it resting on the cover of the
fuel pipe opening.
Type 2
WARNING
Stop refuelling after the fuel nozzle
stops the second time. Additional
fuel will fill the expansion space in
the fuel tank which could lead to fuel
overflowing. Fuel spillage could be
hazardous to other road users.
A
E135935
1.
Press the flap to open it. Open the flap
fully until it engages.
A
B
E139203
A
A
Incorrect position
B
Correct position
3. Do not lift the nozzle during refilling. This
can affect the flow of fuel and shut off of
the fuel nozzle before the fuel tank is full.
E139202
Note: When you insert the fuel nozzle, a
spring loaded inhibitor will open if the
correct size nozzle is detected. This helps
to avoid filling up with the wrong fuel.
125
Fuel and Refuelling
Type 1
E119081
5. Slightly raise the fuel nozzle to remove
it.
E139204
Refuelling with a fuel can
Type 2
Use the funnel which is located in the glove
box.
REFUELLING
CAUTION
Do not attempt to start the engine if
you have filled the fuel tank with the
incorrect fuel. This could damage the
engine. Have the system checked by a
properly trained technician immediately.
REFUELLING - E85
E139205
CAUTION
4. Operate the nozzle within the area
shown.
Do not attempt to start the engine if
you have filled the fuel tank with the
incorrect fuel. This could damage the
engine. Have the system checked by a
properly trained technician immediately.
WARNINGS
We recommend that you remove the
fuel nozzle slowly to allow any
residual fuel to drain into the fuel
tank. Alternatively you can wait 10 seconds
before removing the fuel nozzle.
After refuelling, allow 5 minutes of normal
engine operation above 48 km/h (30 mph)
to reduce the risk of an increased engine
restart time.
Do not remove the nozzle from its
fully inserted position during the
entire refuelling process.
126
Fuel and Refuelling
They are intended as a comparison
between makes and models of vehicles.
They are not intended to represent the real
world fuel consumption you may get from
your vehicle. Real world fuel consumption
is governed by many factors including;
driving style, high speed driving, stop/start
driving, air conditioning usage, the
accessories fitted and towing etc.
FUEL CONSUMPTION
The CO2 and fuel consumption figures are
derived from laboratory tests according to
EEC Directive 80/1268/EEC and
subsequent amendments and are carried
out by all vehicle manufacturers.
Your Ford dealer can give you advice on
improving your fuel consumption.
TECHNICAL SPECIFICATIONS
Focus
Fuel Consumption Figures
Urban
Extra-Urban
Combined
CO2 Emissions
l/100 km
(mpg)
l/100 km
(mpg)
l/100 km
(mpg)
g/km
1.6L Duratec-16V Ti-VCT Sigma Stage V, 5-door, all
except vehicles with DPS6
automatic transmission
8 (35.3)
4.7 (60.1)
5.9 (47.9)
136
1.6L Duratec-16V Ti-VCT Sigma Stage V, 4-door and
estate, all except vehicles
with DPS6 automatic transmission
8.1 (34.9)
4.8 (58.9)
6 (47.1)
139
1.6L Duratec-16V Ti-VCT Sigma Stage V, vehicles
with DPS6 automatic transmission
9.3 (30.4)
4.8 (58.9)
6.4 (44.1)
149
1.6L EcoBoost - Sigma
Stage V, vehicles without
start-stop
8.3 (34)
5 (56.5)
6.2 (45.6)
144
1.6L EcoBoost - Sigma
Stage V, vehicles with startstop
7.7 (36.7)
5 (56.5)
6 (47.1)
139
Variant
127
Fuel and Refuelling
Urban
Extra-Urban
Combined
CO2 Emissions
l/100 km
(mpg)
l/100 km
(mpg)
l/100 km
(mpg)
g/km
9.6 (29.4)
5 (56.5)
6.7 (42.2)
149
9.1 (31)
4.9 (57.6)
6.4 (44.1)
156
1.6L Duratorq-TDCi - DV
Stage V, vehicles without
start-stop
5.7 (49.6)
3.7 (76.3)
4.5 (62.8)
117
1.6L Duratorq-TDCi - DV
Stage V, vehicles with startstop
5.1 (55.4)
3.7 (76.3)
4.2 (67.3)
109
2.0L Duratorq-TDCi - DW
Stage V, vehicles with
manual transmission
6.3 (44.8)
4.2 (67.3)
5 (56.5)
129
2.0L Duratorq-TDCi - DW
Stage V, vehicles with automatic transmission
6.8 (41.5)
4.4 (64.2)
5.3 (53.3)
139
Variant
2.0L Duratec-HE - MI4
Stage V, vehicles with
manual transmission
2.0L Duratec-HE - MI4
Stage V, vehicles with automatic transmission
128
Transmission
MANUAL TRANSMISSION
AUTOMATIC TRANSMISSION
Selecting reverse gear
Selector lever positions
CAUTION
Do not engage reverse gear when the
vehicle is moving. This can cause
damage to the transmission.
E133124
E99067
On some vehicles it is necessary to raise
the collar whilst selecting reverse gear.
Vehicles with 5-speed transmission
CAUTION
Fully depress the clutch pedal and
wait for three seconds before you
select reverse gear.
P
Park
R
Reverse
N
Neutral
D
Drive
S
Sport mode and manual shifting
+
Manual shift up
-
Manual shift down
WARNING
Apply the brakes before moving the
selector lever and keep them applied
until you are ready to move off.
Press the button on the selector lever to
change to each position.
The selector lever position will be shown
in the information display.
Park
WARNINGS
Select park only when your vehicle
is stationary.
129
Transmission
WARNINGS
Apply the parking brake and
select park before leaving your
vehicle. Make sure that the selector
lever is latched in position.
The transmission will select the
appropriate gear for optimum performance
based on ambient temperature, road
gradient, vehicle load and driver input.
Note: An audible warning will sound if you
open the driver's door and you have not
selected park.
Sport Mode
Sport mode and manual shifting
Note: In Sport mode the transmission
operates as normal but gears are selected
more quickly and at higher engine speeds.
In this position, power is not transmitted
to the drive wheels and the transmission
is locked. You can start the engine with the
selector lever in this position.
Note: In Sport mode S will be displayed on
the instrument panel.
Activate Sport mode by moving the
selector lever to position S. Sport mode
will remain active until either you shift
manually up or down the gears using + and
-, or return the selector lever to position D.
Reverse
WARNINGS
Select reverse only when your vehicle
is stationary and the engine is at idle
speed.
Manual shifting
Always come to a complete stop
before shifting out of reverse.
WARNING
Do not hold the buttons permanently
in – or +.
Select reverse to allow the vehicle to move
backwards.
CAUTION
Neutral
The transmission will automatically
downshift when the engine speed is
too low.
In this position, power is not transmitted
to the drive wheels but the transmission is
not locked. You can start the engine with
the selector lever in this position.
Press the - button to shift down and press
the + button to shift up.
Drive
Gears may be skipped by pressing the
buttons repeatedly at short intervals.
Note: A shift will occur only when the
vehicle speed and the engine speed are
appropriate.
Manual mode also provides a kickdown
function. See Kickdown.
Note: You may temporarily override the
current gear selected using the + and buttons.
Hints on driving with an automatic
transmission
Select drive to shift automatically through
the forward gears.
CAUTION
Do not idle the engine for long periods
of time in drive with the brakes
applied.
130
Transmission
Moving off
1. Release the parking brake.
2. Release the brake pedal and press the
accelerator pedal.
4
Stopping
1.
Release the accelerator pedal and
press the brake pedal.
2. Apply the parking brake.
3. Select neutral or park.
E133129
Note: The lever is white.
Kickdown
4. Apply the brake pedal. Using a suitable
tool press and hold the lever forward
while pulling the selector lever out of
the park position and into the neutral
position.
Press the accelerator pedal fully with the
selector lever in the drive position to select
the next lowest gear for optimum
performance. Release the accelerator
pedal when you no longer require
kickdown.
Emergency park position release
lever
Use the lever to move the selector lever
from the park position in the event of an
electrical malfunction or if your vehicle has
a flat battery.
E133128
3
2
1
1. Carefully remove the cover.
2. Remove the retaining clip.
3. Remove the centre console side panel.
131
Brakes
•
•
PRINCIPLE OF OPERATION
Note: Depending on applicable laws and
regulations in the country for which your
vehicle was originally built, the brake lamps
may flash if you brake heavily.
you take corners too fast.
the road surface is poor.
PARKING BRAKE
WARNING
Note: Occasional brake noise is normal and
often does not indicate a concern. In normal
operation, the system may emit occasional
or intermittent squeal or groan noises when
the brakes are applied. Such noises are
usually caused by environmental conditions
such as cold, heat, moisture, road dust, salt
or mud.
Vehicles with an automatic
transmission should always be left
with the selector lever in position P
(Park).
•
•
Disc brakes
•
Wet brake discs result in reduced braking
efficiency. Dab the brake pedal when
driving from a car wash to remove the film
of water.
•
ABS
•
WARNING
The ABS does not relieve you of your
responsibility to drive with due care
and attention.
Press the foot brake pedal firmly.
Pull the parking brake lever up smartly
to its fullest extent.
Do not press the release button while
pulling the lever up.
If your vehicle is parked on a hill and
facing uphill, select first gear or P
(Park) and turn the steering wheel
away from the kerb.
If your vehicle is parked on a hill and
facing downhill, select reverse gear or
P (Park) and turn the steering wheel
towards the kerb.
To release the parking brake, press the
brake pedal firmly, pull the lever up slightly,
depress the release button and push the
lever down.
The ABS helps you to maintain full steering
and directional stability when you brake
heavily in an emergency, by preventing the
road wheels from locking.
HINTS ON DRIVING WITH
ANTI-LOCK BRAKES
When the ABS is operating, the brake pedal
will pulse. This is normal. Maintain pressure
on the brake pedal.
The ABS will not eliminate the dangers
inherent when:
• you drive too close to the vehicle in
front of you.
• the vehicle is aquaplaning.
132
Stability Control
PRINCIPLE OF OPERATION
Stability control (ESP) warning lamp
Electronic stability programme
(ESP)
The ESP warning lamp will flash when the
system is operating. See Warning Lamps
and Indicators (page 71).
WARNING
Emergency brake assist
ESP does not relieve you of your
responsibility to drive with due care
and attention.
WARNING
Emergency brake assist does not
relieve you of your responsibility to
drive with due care and attention.
Emergency brake assist will detect when
you brake heavily by measuring the rate at
which you press the brake pedal. It will
provide maximum braking efficiency as
long as you press the pedal. Emergency
brake assist can reduce stopping distances
in critical situations.
B
B
Trailer stability control
B
WARNING
A
A
B
Trailer stability control does not
relieve you of your responsibility to
tow with due care and attention.
A
Trailer stability control is an enhanced
feature of ESP, and automatically detects
when an attached trailer starts to sway.
E72903
A
without ESP
B
with ESP
If this situation occurs, the system will
automatically brake individual wheels to
stabilise the trailer and vehicle. In case a
very severe sway is detected, the engine
torque will be reduced and the vehicle will
be slowed automatically.
The ESP supports stability when the
vehicle starts to slide away from your
intended path. This is performed by braking
individual wheels and reducing engine
torque as needed.
The system also provides an enhanced
traction control function by reducing
engine torque and may brake individual
wheels if they spin when you accelerate.
This improves your ability to pull away on
slippery roads or loose surfaces, and
improves comfort by limiting wheel spin in
hairpin bends.
USING STABILITY CONTROL
Note: The system will be switched on
automatically every time you switch the
ignition on.
To turn the system off and on. See
Information Displays (page 75).
133
Hill Start Assist
PRINCIPLE OF OPERATION
WARNINGS
At all times you are responsible for
controlling the vehicle, supervising
the system and intervening, if
required.
The system makes it easier to pull away
when the vehicle is on a slope without the
need to use the parking brake.
When the system is active, the vehicle will
remain stationary on the slope for a short
time after you release the brake pedal.
During this time, you have time to move
your foot from the brake to the accelerator
pedal and pull away. The brakes are
released automatically once the engine
has developed sufficient drive to prevent
the vehicle from rolling down the slope.
This is an advantage when pulling away
on a slope, for example from a car park
ramp, traffic lights or when reversing uphill
into a parking space.
If a malfunction is detected when the
system is active, the system will be
deactivated and a message will be
shown in the display. See Information
Messages (page 83).
You can activate the system only if the
following conditions have been met:
• The engine is running.
• The system is switched on.
• On vehicles with manual transmission,
the clutch pedal is pressed.
• No failure mode is present.
WARNING
The system does not replace the
parking brake. When you leave the
vehicle, always apply the parking
brake and select first or reverse gear.
To activate the system:
1.
Press the brake pedal to bring the
vehicle to a complete standstill. Keep
the brake pedal depressed.
2. If the sensors detect that the vehicle is
on a slope the system will be activated
automatically.
3. When you remove your foot from the
brake pedal, the vehicle will remain on
the slope without rolling away for a
short time. This hold time will
automatically be extended if you are
in the process of driving off.
4. Drive off in the normal manner. The
brakes will be released automatically.
USING HILL START ASSIST
The system is activated automatically
when you stop your vehicle on a slope
greater than 3%. The system operates with
the vehicle facing downhill if reverse gear
is selected and with the vehicle facing
uphill if any forward gear is selected.
Vehicles with manual
transmission only
The system can be switched on and off
using the information display. See General
Information (page 75).
Deactivating the system
To deactivate the system, perform one of
the following:
Activating the system
WARNINGS
You must remain in the vehicle once
you have activated the system.
134
Hill Start Assist
•
•
•
Wait for a short time until the system
deactivates automatically.
If a forward gear was selected when
the system became active, select
reverse gear.
If reverse gear was selected when the
system became active, select a
forward gear.
135
Parking Aids
Note: The outer sensors may detect the
side walls of a garage. If the distance
between the outer sensor and the side wall
remains constant for three seconds, the
tone will switch off. As you continue, the
inner sensors will detect rearward objects.
PRINCIPLE OF OPERATION
WARNING
The system does not relieve you of
your responsibility to drive with due
care and attention.
USING THE PARKING AID VEHICLES WITH: REAR
PARKING AID
CAUTIONS
Vehicles fitted with a trailer tow
module not approved by us may not
correctly detect obstacles.
WARNING
The sensors may not detect objects
in heavy rain or other conditions that
cause disruptive reflections.
The parking aid does not relieve you
of your responsibility to drive with
due care and attention.
The sensors may not detect objects
with surfaces that absorb ultrasonic
waves.
The parking aid does not detect
obstacles moving away from the
vehicle. They will only be detected
shortly after they start to move towards
the vehicle again.
If you use a high pressure spray to
wash your vehicle, only spray the
sensors briefly from a distance not
less than 20 centimetres (8 inches).
E77927
The parking aid is automatically activated
when you select reverse gear with the
ignition switched on.
Parking aid sends tones via the audio
system fitted and approved by us. If
this is not working the parking aid
system will not work.
You will hear an intermittent tone at a
distance of approximately 150 centimetres
(59 inches) between the obstacle and rear
bumper and approximately 50 centimetres
(20 inches) to the side. Decreasing the
distance accelerates the intermittent tone.
Note: On vehicles fitted with a tow ball
arm, the rear parking aid is deactivated
automatically when any trailer lamps (or
lighting boards) are connected to the 13-pin
socket via a trailer tow module we have
approved.
Note: Keep the sensors free from dirt, ice
and snow. Do not clean with sharp objects.
Note: The parking aid may emit false tones
if it detects a signal using the same
frequency as the sensors or if the vehicle is
fully laden.
136
Parking Aids
A
E130180
E130178
A
A trailer symbol indicates there is a trailer
attached and the system is disabled.
Distance Indicator.
As the distance decreases the indicator
moves towards the vehicle.
USING THE PARKING AID VEHICLES WITH: FRONT AND
REAR PARKING AID
A continuous tone will start at a distance
of less than 30 centimetres (11 inches) to
the rear bumper.
WARNING
Note: On Vehicles with a tow bar fitted and
approved by us the continuous tone will
start at a distance of 45 centimetres (18
inches) from the rear bumper.
The parking aid does not relieve you
of your responsibility to drive with
due care and attention.
Switching the parking aid on and
off
The parking aid is per default off. To switch
the parking aid on, select reverse gear or
press the switch in the instrument panel.
For item location: See At a Glance (page
10).
A
The light in the switch illuminates when
the parking aid is activated.
E130179
To turn it off, press the switch again.
A
Malfunction indicator.
Note: If a malfunction is indicated the
system will be disabled. Have the system
checked by a properly trained technician.
137
Parking Aids
Manoeuvring with the parking aid
A
You will hear an alternating tone from the
front and rear if obstacles are closer than
30 centimetres (11 inches) to the front and
rear bumpers.
B
1
A
D
C
2
E130382
A
E130381
1
Reverse gear selected
2
Neutral or forward gear selected
A
Display and tone
B
Display and tone
C
Display only
D
Display and tone
Distance Indicator.
As the distance decreases the indicator
moves towards the vehicle.
A
You will hear an intermittent tone at a
distance of approximately 150 centimetres
(59 inches) between the obstacle and rear
bumper, approximately 80 centimetres (31
inches) between the obstacle and front
bumper and approximately 50 centimetres
(20 inches) to the side. Decreasing the
distance accelerates the intermittent tone.
A continuous tone will start at a distance
of less than 30 centimetres (11 inches) to
the front or rear bumper.
E130383
A
Malfuction indicator.
Note: If a malfunction is indicated the
system will be disabled. Have the system
checked by a properly trained technician.
Note: On vehicles with a tow bar fitted and
approved by us the continuous tone will
start at a distance of 45 centimetres (18
inches) from the rear bumper.
138
Parking Aids
E130180
A trailer symbol indicates there is a trailer
attached and the rear sensors are disabled.
139
Rear view camera
PRINCIPLE OF OPERATION
The camera is a visual aid for use when
reversing.
WARNING
The system does not relieve you of
your responsibility to drive with due
care and attention.
CAUTIONS
If you use a high pressure spray to
wash your vehicle, only spray the
camera briefly from a distance not
less than 20 centimetres (8 inches).
E99105
Activating the rear view camera
Do not apply pressure to the camera.
CAUTION
The camera may not detect objects
that are close to the vehicle.
Note: Keep the camera free from dirt, ice
and snow. Do not clean with sharp objects,
degreaser, wax or organic products. Use only
a soft cloth.
With the ignition and the audio unit
switched on:
1. Press the parking aid switch in the
instrument panel. For item location:
See At a Glance (page 10). Or,
2. Engage reverse gear.
During operation, guide lines appear in the
display which represent your vehicle's path
and approximate distance from rearward
objects.
USING THE REAR VIEW
CAMERA
The image is displayed on the screen.
WARNINGS
The operation of the camera may
vary depending on the ambient
temperature, vehicle and road
conditions.
The camera may not operate correctly in
the following conditions:
• Dark areas.
• Intense light.
• If the ambient temperature increases
or decreases rapidly.
• If the camera is wet, for example in rain
or high humidity.
• If the camera's view is obstructed, for
example by mud.
The lamp in the switch illuminates when
the system is activated.
The distances shown in the display
may differ from the actual distance.
Do not place objects in front of the
camera.
The camera is located on the luggage
compartment lid near the handle.
140
Rear view camera
Using the display
D
CAUTIONS
Obstacles above the camera position
will not be shown. Inspect the area
behind your vehicle if necessary.
E
D
C
C
B
B
A
A
Marks are for general guidance only,
and are calculated for vehicles in
maximum load conditions on an even
road surface.
The lines show a projected vehicle path
(based on the current steering wheel
angle) and the distance from the exterior
mirrors and rear bumper.
E99458
141
A
Exterior mirror clearance - 0.1
metre (4 inches)
B
Red - up to 0.3 (12 inches)
C
Amber - 0.3 - 0.6 metre (12 - 24
inches)
Rear view camera
D
Green - 0.6 - 0.9 metre (24 - 35
inches)
E
Amber - centre line of the
projected vehicle path
Note: The green line is extended from 0.9
metre (35 inches) up to a distance of 3.2
metres (126 inches).
Note: When reversing with a trailer, the lines
on the screen are not shown. The camera
will show the vehicle direction and not the
trailer.
Deactivating the rear view camera
Note: Disengage reverse gear. The display
will stay on for a short period before
switching off.
Note: The system will automatically switch
off once the vehicle speed has reached
approximately 15 km/h (9 mph).
Press the parking aid switch in the
instrument panel. For item location: See
At a Glance (page 10).
Vehicles with parking aid
The display will additionally show a
coloured distance bar. This guide indicates
the distance from the rear bumper to the
detected obstacle.
These are colour coded as follows:
• Green - 0.6 to 1.8 metres (24 - 71
inches).
• Amber - 0.3 to 0.6 metre (12 - 24
inches).
• Red - 0.3 metre (12 inches) or less.
142
Active Park Assist
The system will detect a suitable parallel
parking space and steer the vehicle into
the space. The system controls the
steering while the driver controls the
accelerator, transmission and brakes. The
manoeuvre can be stopped at any time by
holding the steering wheel or pressing the
active park assist switch. See At a Glance
(page 10).
PRINCIPLE OF OPERATION
WARNINGS
The system does not relieve you of
your responsibility to drive with due
care and attention.
At all times you are responsible for
controlling the vehicle, supervising
the system and intervening if
required.
The system will visually and audibly
instruct the driver throughout the
procedure to safely park the vehicle.
You must observe that the selected
space remains clear of obstructions
at all times in the manoeuver.
USING ACTIVE PARK ASSIST
Vehicles with overhanging loads,
street furniture and other items may
not be detected by the system. You
must make sure that the selected space
is suitable for parking.
CAUTIONS
The sensors may not detect objects
in heavy rain or other conditions that
cause disruptive reflections.
Do not use the system if a trailer is
attached to the vehicle.
The sensors may not detect objects
with surfaces that absorb ultrasonic
waves.
Do not use the system if a bike rack
is attached to the back of the vehicle.
The sensors may not detect the kerb.
Do not use the system if an
overhanging item is attached to the
roof.
Note: If the traction control system is
disabled active park assist will not be
available. See General Information (page
75).
If the manoeuvre is interrupted
before completion, the system will
be disabled. The steering wheel
position will not indicate the true position
of the steering and you will have to take
control of the vehicle.
The system will not align the vehicle
correctly if:
• a spare tyre, or a tyre worn significantly
more than the other tyres is used
Make sure that loose clothing, your
hands or your arms do not get caught
in the rotating steering wheel.
•
•
•
•
143
the factory installed tyre size is not
used on the vehicle
the tyres skid
you allow the vehicle to roll
the weather conditions are poor (heavy
rain, snow, fog, etc).
Active Park Assist
Move forwards at a maximum speed of 30
km/h (18 mph). Press the active park assist
switch. See At a Glance (page 10). Use
the direction indicator lever to select
searching either to the left-hand side or
right-hand side of the vehicle.
Note: If no selection is made via the
direction indicator lever the system will
default to the passenger side of the vehicle.
A
E130107
Note: To disable the chimes: See
Personalised Settings (page 82).
Note: The arrow symbols or graphics in the
display indicate on which side of the vehicle
the system will park. The display will also
advise you when to select reverse gear.
The information and entertainment display
will inform you and a chime will be heard
when a suitable space is found. To park
the vehicle, follow the instructions on the
information and entertainment display.
Slow down and stop at approximately
position A, then follow the system
instructions.
E130108
Move the vehicle backwards cautiously
using the accelerator and brake pedals to
control the vehicle. Parking aid warning
tones will sound. Stop the vehicle when
you hear a continuous tone.
WARNING
If a speed of 10 km/h (6 mph) is
exceeded the system will be disabled
and you will need to take full control
of the vehicle.
144
Active Park Assist
You can take control of the manoeuvre by
holding the steering wheel. A message may
appear that the system can be resumed.
To accept this message press the active
park assist switch. See At a Glance (page
10).
E130109
Move the vehicle forwards. Stop the
vehicle when you hear a continuous tone.
Repeat the above steps until the vehicle is
satisfactory parked. The display will
indicate when the system has finished the
manoeuvre.
145
Cruise Control
Setting a speed
PRINCIPLE OF OPERATION
Press the SET+ switch or the SET- switch
to store and maintain your current speed.
The cruise control indicator will illuminate.
See Warning Lamps and Indicators
(page 71).
WARNING
The system does not relieve you of
your responsibility to drive with due
care and attention.
Changing the set speed
Cruise control allows you to control your
speed using the switches on the steering
wheel. You can use cruise control when
you exceed approximately 30 km/h (20
mph).
WARNING
When you are going downhill, your
speed may increase above the set
speed. The system will not apply the
brakes. Change down a gear and press the
SET- switch to assist the system in
maintaining the set speed.
USING CRUISE CONTROL
WARNING
Note: If you accelerate by pressing the
accelerator pedal, the set speed will not
change. When you release the accelerator
pedal, you will return to the speed that you
previously set.
Do not use cruise control in heavy
traffic, on twisty roads or when the
road surface is slippery.
Switching cruise control on
A
B
E130073
E130072
Note: The system is ready for you to set a
speed.
A
Accelerate
B
Decelerate
Cancelling the set speed
Press the brake pedal or pull the CAN
switch.
146
Cruise Control
Note: The system will no longer control
your speed. The cruise control indicator will
not illuminate but the system will retain the
speed that you previously set.
Resuming the set speed
Pull the RES switch.
The cruise control indicator will illuminate
and the system will attempt to resume the
speed that you previously set.
Switching cruise control off
E130072
The system will not retain the speed that
you previously set. The cruise control
indicator will not illuminate.
147
Adaptive cruise control (ACC)
Note: When adaptive cruise control is
activated, you may hear some unusual
sounds during automatic braking. This is
normal and caused by the automatic
braking system.
PRINCIPLE OF OPERATION
WARNINGS
The system is not a collision warning
or avoidance system. The separate
forward alert function provides a
collision warning and mitigation feature.
See Forward alert function (page 152).
You must intervene if the system does not
detect a vehicle in front.
Note: Keep the front of the vehicle free
from dirt, metal badges or objects, including
vehicle front protectors and additional lights
which may prevent the sensor from
operating.
The system is designed to help you
maintain a gap from the vehicle ahead or
a set road speed if there is no slower
vehicle ahead. The system is intended to
provide enhanced operation of the vehicle
when following other vehicles which are in
the same lane and travelling in the same
direction.
When driving you are responsible for
maintaining the correct distance and
speed, even when adaptive cruise
control is used. You must always pay
attention to the traffic conditions and
intervene when adaptive cruise control is
not maintaining a suitable speed or
suitable distance.
The system is based on the use of a radar
sensor which projects a beam directly
forward of the vehicle. This beam will
detect any vehicle ahead within the
system's range.
The system does not relieve you of
your responsibility to drive with due
care and attention.
The system does not brake for slow
or stationary vehicles, pedestrians,
objects in the road, oncoming and
crossing vehicles.
The radar sensor is mounted behind the
front grille.
CAUTIONS
Only use adaptive cruise control when
conditions are favourable, for example
on motorways and main roads with
steady free flowing traffic.
Do not use in poor visibility,
specifically fog, heavy rain, spray or
snow.
Do not use on icy or slippery roads.
Do not use the system when entering
or leaving a motorway.
The radar sensor has a limited field of
vision. In some situations it may
detect a vehicle other than the one
expected or not detect any vehicle at all.
148
Adaptive cruise control (ACC)
Detection beam issues
Automatic braking with ACC
WARNINGS
You must take immediate action
once alerted, as the adaptive cruise
control braking will not be sufficient
to keep a safe distance to the vehicle in
front.
In some cases there may be no
warning or the warning may be
delayed. You should always apply
the brakes when necessary.
When following a vehicle in front of
you, adaptive cruise control will not
automatically decelerate to a stop.
The system will automatically brake for
you, if required to maintain the set gap
between your vehicle and the one detected
in front. This braking capacity is limited to
approximately 30% of the total manual
braking capacity to ensure smooth and
comfortable cruising. If the car needs to
brake more heavily than this, and you do
not intervene by braking manually, an
alarm will sound and a warning symbol will
be displayed in the cluster.
E71621
Detection issues can occur:
•
•
With vehicles that edge into your lane
that can only be detected once they
have moved fully into your lane (A).
Motorcycles may be detected late, or
not at all. (B)
With vehicles in front when going into
and coming out of a bend (C). The
detection beam will not follow sharp
curves in the road.
In these cases the system may brake late
or unexpectedly. You should stay alert and
intervene if necessary.
149
Adaptive cruise control (ACC)
Changing the set speed
USING ADAPTIVE CRUISE
CONTROL
Note: Vehicle speed may be increased and
decreased at intervals of 5 km/h or 5 mph.
The system is operated by adjustment
controls mounted on the steering wheel.
Note: If the system does not react to these
changes the reason may be that the gap
interval to the vehicle in front prevents an
increase in speed.
A
Press switch A to increase or switch B to
decrease the set speed until the desired
set speed is shown in the information
display. The vehicle speed will gradually
change to the selected speed.
F
Setting the vehicle gap
E
CAUTION
E133195
D
C
A
Set speed increase
B
Set speed decrease
C
ACC on/off
D
ACC gap increase
E
ACC gap decrease
F
ACC cancel/resume
Use the appropriate gap setting in
accordance with local traffic
regulations.
B
Note: The gap setting is time dependent
and therefore the distance will
automatically adjust with your speed. For
example on a gap setting of four bars, the
time gap is 1.8 seconds. This will mean that
at a speed of 100 km/h (62 mph), the
distance to the vehicle in front will be
maintained at 50 metres (164 feet).
Note: If the accelerator is depressed for a
short period, for example when overtaking,
the system is temporarily deactivated and
then reactivated when the accelerator pedal
is released. A message is displayed in the
information display.
Switching the system on
Press switch C. The system is set to
standby mode.
Setting a speed
Note: The gap setting will remain
unchanged during ignition cycles.
Note: The system must be in standby
mode.
Press switch A or switch B to select your
desired cruise speed. The speed is
displayed in the information display and
stored as the set speed.
E82311
150
Adaptive cruise control (ACC)
The distance between you and the vehicle
detected in front is maintained by a
variable setting. There are five steps which
are represented by horizontal bars
displayed in the information display. One
bar indicates the smallest gap and five
bars indicates the largest gap. These bars
are shown empty when in standby mode
and filled when in active mode.
Press the brake pedal or pull switch F to
cancel the system. The system will return
to standby mode allowing you full manual
control of the vehicle. The set speed and
gap setting are retained in the memory.
If no vehicle is detected in front, then only
your vehicle is displayed in the information
display below the bars. The system will
maintain the set speed when conditions
permit. The set gap is maintained and
displayed.
Switching the system off
If a vehicle is detected by the sensor, the
display will show another vehicle above
the horizontal bars:
Automatic deactivation
Pull switch F again to resume. The system
will resume with the previously set speed
and vehicle gap setting if conditions permit.
Press switch C to turn the system off.
Note: When deactivating the system by
pressing switch C, the stored speed is not
retained.
Note: If the engine speed drops too low, a
message is displayed in the information
display instructing you to change down a
gear (manual transmission only). If you do
not follow this recommendation then the
system will go into automatic deactivation
mode.
Note: The system will not operate if
traction control has been switched off.
E82312
The system is dependent on various other
safety systems, for example ABS and ESP.
If any of these systems are malfunctioning
or reacting to an emergency, the system is
automatically deactivated.
This is a follow mode, and the system will
accelerate or decelerate as necessary to
maintain the set gap.
Pull switch E to decrease the gap or switch
D to increase the gap. The gap selected
will be represented by the number of bars
in the display.
In the event of automatic deactivation a
signal will sound and the message is
displayed in the information display. See
Information Messages (page 83). You
must then intervene and adapt your driving
and speed to vehicles in front.
Note: The recommended gap setting is four
or five bars.
Temporarily deactivating the
system
An automatic deactivation can be due to
the:
Note: The system is cancelled when the
gear lever is moved to a neutral position or
if the accelerator pedal or clutch is
depressed for a long period of time.
•
•
151
vehicle speed falling below 30 km/h
(20 mph)
wheels losing traction
Adaptive cruise control (ACC)
•
•
•
•
Note: The collision alerts will only occur if
the system is switched on, however the
brake support is always on and cannot be
turned off.
brake temperature being too high, for
example when driving on mountainous
or hilly roads
engine speed being too low
radar sensor being covered
parking brake being applied.
Note: The system may be used with or
without the Adaptive cruise control system
being activated.
The system assists you by warning of the
risk of a collision with a vehicle in front.
FORWARD ALERT FUNCTION
The system alerts you by warning chimes
and a visual warning in the information
display. See Information Messages
(page 83).
WARNINGS
Never wait for a collision warning.
When driving you are responsible for
maintaining the correct distance and
speed, even when the system is used.
Brake support is activated to enable full
braking effectiveness, and reduce the
severity of a collision with the vehicle in
front.
The system will only react to vehicles
in front travelling in the same
direction and will not react to slow
or stationary vehicles.
Switching the system on and off
Never drive in a manner to provoke
the system. The system is designed
to assist in emergencies only.
Note: When the system is switched off, a
warning indicator will remain illuminated in
the information display. See Warning
Lamps and Indicators (page 71).
CAUTIONS
Warnings may be triggered late, be
absent or triggered unnecessarily due
to detection beam issues. See
Principle of Operation (page 148).
Note: The system status and settings will
remain unchanged during ignition cycles.
The system can be switched on and off
using the information display. See General
Information (page 75).
The system uses the same radar
sensors as adaptive cruise control and
therefore has the same limitations.
See Principle of Operation (page 148).
Adjusting the warning sensitivity
You may adjust the system warning
sensitivity using the buttons on the steering
wheel. See General Information (page
75). This controls how early the visual and
audible warning is activated.
Note: The brake support system only
reduces the collision speed if you brake
immediately once alerted.
Note: If the brake pedal is depressed
sufficiently quickly then braking is
implemented with full brake function, even
if the force on the pedal is light.
Note: Brake support prepares the brake
system for rapid braking and the brakes are
applied gently, which may be noticed as a
slight jerk.
152
Speed Limiter
Switching the system on and off
PRINCIPLE OF OPERATION
Press switch B. The information display
will prompt for a speed to be set.
WARNING
When you are going downhill, your
speed may increase above the set
speed. The system will not apply the
brakes but a warning will be given.
Setting the speed limit
Use the cruise control switches to alter the
maximum speed setting.
Press switch A or switch C to select your
desired speed limit. The speed is displayed
in the information display and stored as
the set speed.
The system allows you to set a speed, to
which the vehicle then becomes limited.
The set speed will become the effective
maximum speed of the vehicle, but with
the option to temporarily exceed this limit
if required.
Pull switch D to cancel the limiter and
place it in standby mode. The information
display will confirm deactivation by
showing the set speed crossed out.
USING THE SPEED LIMITER
Note: The set speed limit can be
intentionally exceeded for a short period if
required, for example when overtaking.
Pull switch D again to resume the limiter.
The information display will confirm the
system is active by showing the set speed
again.
The system is operated by adjustment
controls mounted on the steering wheel.
Intentionally exceeding the set
speed limit
Depress the accelerator fully to temporarily
deactivate the system. The system will
reactivate once the vehicle speed drops
below the set speed.
A
D
System warnings
B
If the set limit is accidentally exceeded, for
example driving downhill, the information
display will show the set speed flashing
together with an audible warning chime.
C
If the set limit is intentionally exceeded the
information display will show the set speed
crossed out.
E133198
A
Set speed increase
B
Speed limiter on/off
C
Set speed decrease
D
Speed limiter cancel/resume
153
Driver Alert
Note: Keep the windscreen free from
obstructions such as bird droppings, insects
and snow or ice.
PRINCIPLE OF OPERATION
WARNINGS
The system does not relieve you of
your responsibility to drive with due
care and attention.
Note: The system is intended as a driver aid
when driving on fast main roads and
motorways.
Note: The system calculates an alertness
level at vehicle speeds above approximately
65 km/h (40 mph).
At all times you are responsible for
controlling the vehicle, supervising
the system and intervening if
required.
If the sensor becomes blocked the
system may not function.
The system automatically monitors your
driving behaviour using various inputs
including the front camera sensor.
Take regular rest breaks as required
and do not wait for the system to
warn you if you feel tired.
If the system detects that you are
becoming drowsy or there is a deterioration
in your driving, the system will alert you.
Take rest breaks only where it is safe
to do so.
USING DRIVER ALERT
Certain driving styles and behaviour
may result in the system issuing a
warning even if you are not feeling
Switching the system on and off
Note: The system status will remain
unchanged during ignition cycles.
tired.
Activate the system using the information
display. See Information Displays (page
75).
CAUTIONS
In cold and severe weather conditions
the system may not function. Rain,
snow, spray and large contrasts in
lighting can all influence the sensor.
Once activated the system will calculate
your alertness level based upon your
driving behaviour in relation to the lane
markings, and other factors.
The system will not operate if the
sensor cannot track the road lane
markings.
System warnings
The system may not operate in areas
during roadworks construction.
Note: The system will not issue warnings
below approximately 65 km/h (40 mph).
The system may not operate on roads
with sharp bends or narrow lanes.
The warning system is in two stages. At
first the system issues a temporary warning
that a rest should be taken. This message
will only appear for a short time. If a rest is
not then taken a further warning may be
issued which will remain in the information
display until cancelled. See Information
Messages (page 83).
Do not carry out windscreen repairs in
the immediate area surrounding the
sensor.
If your vehicle is fitted with a
suspension kit not approved by us, the
system may not function correctly.
Press OK on the steering wheel control to
remove the warning.
154
Driver Alert
System display
Resetting the system
When active the system will run
automatically in the background and only
issue warnings if required. You can view
the status at any time using the
information display. See General
Information (page 75).
You can reset the system by either:
• Switching the ignition off and on.
• Stopping the vehicle and then opening
and closing the driver's door.
The alertness level is shown by six steps
as a coloured bar.
E131358
Alertness level is fine, no rest required.
E131359
Alertness level is critical, indicating that a
rest should be taken as soon as safely
possible.
The status bar will travel from left to right
as the calculated alertness level
decreases. As the rest icon is approached
the colour turns from green to yellow and
then finally red when a rest break must be
taken.
•
•
•
Green - No rest required.
Yellow - First (temporary) warning.
Red - Second warning.
Note: The alertness level will be shown in
grey if the camera sensor cannot track the
road lane markings or if the vehicle speed
drops below approximately 65 km/h (40
mph).
155
Lane Departure Warning
Note: The system is intended as a driver aid
when driving on fast main roads and
motorways.
PRINCIPLE OF OPERATION
WARNINGS
The system does not relieve you of
your responsibility to drive with due
care and attention.
Note: The system may not operate during
hard braking or acceleration and, when you
are intentionally steering the vehicle.
Note: The system will operate with a
minimum of one tracked lane marking.
At all times you are responsible for
controlling the vehicle, supervising
the system and intervening if
required.
Note: The system will only operate above
vehicle speeds of approximately 65 km/h
(40 mph).
If the sensor becomes blocked the
system may not function.
A sensor is mounted behind the interior
rear view mirror. It continuously monitors
conditions to alert you of unintentional
lane drifting at high speeds.
Lane markings may not always be
properly tracked by the sensor. Other
structures or objects may sometimes
be incorrectly detected as a lane marking,
resulting in a false or missed warning.
The system will automatically detect and
track the lane markings on the road. If it
detects that the vehicle is unintentionally
drifting towards the lane boundaries then
a visual warning will be displayed in the
information display. There is also a warning
given in the form of a vibration felt through
the steering wheel.
CAUTIONS
In cold and severe weather conditions
the system may not function. Rain,
snow, spray and large contrasts in
lighting can all influence the sensor.
The system will not operate if the
sensor cannot track the road lane
markings.
USING LANE DEPARTURE
WARNING
The system may not operate in areas
during roadworks construction.
Switching the system on and off
The system may not operate on roads
with sharp bends or narrow lanes.
Note: When the system is switched off, a
warning indicator will remain illuminated in
the information display. See Warning
Lamps and Indicators (page 71).
Do not carry out windscreen repairs in
the immediate area surrounding the
sensor.
Note: The system status and settings will
remain unchanged during ignition cycles.
If your vehicle is fitted with a
suspension kit not approved by us, the
system may not function correctly.
Note: Keep the windscreen free from
obstructions such as bird droppings, insects
and snow or ice.
E132099
156
Lane Departure Warning
The lane markings are colour coded as
follows:
• Green - The system is ready to warn
you of any unintentional lane
departure.
• Red - The vehicle is approaching or is
too close to the detected lane
boundary. Take immediate safe action
to reposition the vehicle.
• Grey - The relevant lane boundary will
be suppressed.
Activate and deactivate the system using
the button on the indicator stalk.
Press the button to turn the system off.
Press the button twice to turn the system
on.
Setting the steering wheel
vibration level
The system has three intensity levels which
can be set using the information display.
See General Information (page 75).
Instances where a lane boundary may be
suppressed:
• Lane markings on the road may not be
detected by the sensor.
• The direction indicator for that side of
the vehicle is on.
• During hard acceleration and braking,
or if direct steering is applied.
• Vehicle speed is outside the operating
limits
• If there is an ABS or Stability Control
(ESP) intervention.
• Narrow lane width.
Setting the system sensitivity
You can adjust how quickly the system
warns you of a dangerous situation. The
system has two sensitivity levels which can
be set using the information display. See
General Information (page 75).
System warnings
If the lane markings turn red or a vibration
is felt through the steering wheel you must
take immediate and safe action to align
the vehicle and correct any unintended
lane drift.
E132651
A column of lane markings is displayed
either side of the vehicle graphic.
157
Lane Keeping Aid
Note: Keep the windscreen free from
obstructions such as bird droppings, insects
and snow or ice.
PRINCIPLE OF OPERATION
WARNINGS
The system does not relieve you of
your responsibility to drive with due
care and attention.
Note: The system is intended as a driver aid
when driving on fast main roads and
motorways.
Note: The system may not operate during
hard braking or acceleration and when you
are intentionally steering the vehicle.
At all times you are responsible for
controlling the vehicle, supervising
the system and intervening if
required.
Note: The system will operate with a
minimum of one tracked lane marking.
If the sensor becomes blocked the
system may not function.
Note: The system will only operate
between vehicle speeds of approximately
65 km/h (40 mph) and 180 km/h (112 mph).
Lane markings may not always be
properly tracked by the sensor. Other
structures or objects may sometimes
be incorrectly detected as a lane marking,
resulting in a false or missed warning in
conjunction with a false or missed steering
intervention.
Note: If the system does not detect an
active steering input by the driver it will be
temporarily deactivated until you resume
control. The system alerts you with a
warning chime and a message in the display.
Always have your hands on the
steering wheel in case you need to
overrule the system.
A sensor is mounted behind the interior
rear view mirror. It continuously monitors
conditions to alert you of unintentional
lane drifting at high speeds.
The system may not operate in areas
during roadworks construction.
The system will automatically detect and
track the lane markings on the road. If it
detects that the vehicle is unintentionally
drifting towards the lane boundaries then
a visual warning will be displayed in the
information display. The system will also
automatically apply a steering torque to
correct the vehicle path. If the system is
unable to correct the vehicle path a lane
departure warning will be given. See Using
lane departure warning (page 156).
The system may not operate on roads
with sharp bends or narrow lanes.
USING THE LANE KEEPING AID
CAUTIONS
In cold and severe weather conditions
the system may not function. Rain,
snow, spray and large contrasts in
lighting can all influence the sensor.
The system will not operate if the
sensor cannot track the road lane
markings.
Do not carry out windscreen repairs in
the immediate area surrounding the
sensor.
Switching the system on and off
If your vehicle is fitted with a
suspension kit not approved by us, the
system may not function correctly.
Note: When the system has been switched
on, lane departure warning is per default on.
Note: The system is per default off.
158
Lane Keeping Aid
•
•
E132099
Activate and deactivate the system using
the button on the indicator stalk.
Red - The vehicle is approaching or is
too close to the detected lane
boundary. A warning is given in the
form of a vibration felt through the
steering wheel. Take immediate safe
action to reposition the vehicle.
Grey - The relevant lane boundary will
be suppressed.
Instances where a lane boundary may be
suppressed:
• Lane markings on the road may not be
detected by the sensor.
• The direction indicator for that side of
the vehicle is on.
• During hard acceleration and braking,
or if direct steering is applied.
• Vehicle speed is outside the operating
limits
• If there is an ABS or Stability Control
(ESP) intervention.
• Narrow lane width.
Press the button three times to switch the
system on. Press the button again to turn
the system off.
System warnings
Note: The system can be overridden at any
time during its operation by turning the
steering wheel.
E132651
A column of lane markings is displayed
either side of the vehicle graphic.
The lane markings are colour coded as
follows:
• Green - The system is ready to
intervene if an unintentional lane
departure may occur.
• Yellow - The system will automatically
apply a steering torque to align the
vehicle path and correct any
unintended lane drift.
159
Traffic Sign Recognition
The system will automatically detect
recognizable traffic signs, for example
speed limit signs, no overtaking signs and
speed limit cancellation signs.
PRINCIPLE OF OPERATION
WARNINGS
The system does not relieve you of
your responsibility to drive with due
care and attention.
USING TRAFFIC SIGN
RECOGNITION
At all times you are responsible for
controlling the vehicle, supervising
the system and intervening if
required.
Switching the system on and off
Note: The system status and settings will
remain unchanged during ignition cycles.
If the sensor becomes blocked the
system may not function.
The system can be switched on and off
using the information display. See General
Information (page 75).
CAUTIONS
In cold and severe weather conditions
the system may not function. Rain,
snow, spray and large contrasts in
lighting can all influence the sensor.
Setting the system speed warning
The system has a number of speed
warning levels which can be set using the
information display. See General
Information (page 75).
Do not carry out windscreen repairs in
the immediate area surrounding the
sensor.
System display
If your vehicle is fitted with a
suspension kit not approved by us, the
system may not function correctly.
Always fit Ford Original Parts when
replacing headlamp bulbs. Other
bulbs may reduce system
performance.
Note: Keep the windscreen free from
obstructions such as bird droppings, insects
and snow or ice.
E132994
The system can display two traffic signs
in parallel.
Note: The system may not detect all traffic
signs.
You can view the status at any time using
the information display.
Note: The system is designed to read signs
meeting the Vienna convention.
The system display is in four stages as
follows:
1. All new recognisable traffic signs will
appear brighter than the other warning
signs in the display.
2. After a predetermined time they will
be shown normally.
A sensor is mounted behind the interior
rear view mirror. It continuously monitors
road signs to alert you of the current legal
speed limit and overtaking regulations.
160
Traffic Sign Recognition
3. After a predetermined distance they
will be shown greyed out.
4. After another predetermined distance
they will be deleted.
If a supplementary traffic sign is detected,
for example a reduced speed limit in wet
road conditions sign, it will not be shown
but will appear as an empty box
underneath the respective sign.
161
Active City Stop
PRINCIPLE OF OPERATION
CAUTIONS
If your vehicle is fitted with a
windscreen not approved by us, the
system may not function correctly.
WARNINGS
The system does not relieve you of
your responsibility to drive with due
care and attention.
If the engine stops after the system
has been activated, the hazard
warning flashers will be activated.
At all times you are responsible for
controlling the vehicle, supervising
the system and intervening if
required.
Note: Keep the windscreen free from
obstructions such as bird droppings, insects
and snow or ice.
Never look directly into the sensor
with any type of object, there is a risk
of eye injury.
Note: Keep the bonnet free of ice and snow,
otherwise the system may not function
correctly.
If the sensor becomes blocked the
system may not function.
A sensor is mounted behind the interior
rear view mirror. It continuously monitors
conditions to decide when to intervene.
To achieve full system performance,
the brake system needs to be
bedded in. See Running-In (page
The system is designed to help you reduce
low speed collisions into the rear of
another vehicle. It will also help you reduce
the impact damage or potentially avoid
the collision completely.
176).
The system performance may vary
depending on the vehicle and road
conditions.
The system operates at speeds below
approximately 30 km/h (19 mph) by
applying the brakes when the sensor
detects that a collision is likely.
The system will not react to vehicles
driving in a different direction.
The system will not react to bicycles,
motorcycles, people or animals.
You must depress the brake pedal to
obtain full braking force.
When the ignition is on the sensor
will constantly transmit a laser
beam.
When the system is braking or has
automatically applied the brakes, a
message will be shown in the display.
The system will not operate during
harsh acceleration.
For laser sensor information and data: See
Type approvals (page 287).
CAUTIONS
In cold and severe weather conditions
the system may not function. Rain,
snow, spray and ice can all influence
the sensor.
USING ACTIVE CITY STOP
WARNING
Never look directly into the sensor
with any type of object, there is a risk
of eye injury.
Do not carry out windscreen repairs in
the immediate area surrounding the
sensor.
162
Active City Stop
Switching the system on and off
Note: The system is per default on.
Note: In certain situations, it may be
advisable to disable the system, for example
driving off road when objects may cover the
windscreen.
Activate and deactivate the system using
the information display. See General
Information (page 75).
163
Load Carrying
GENERAL INFORMATION
WARNINGS
Use load securing straps to an
approved standard, e.g. DIN.
Make sure that you secure all loose
items properly.
Place luggage and other loads as low
and as far forward as possible within
the luggage or loadspace.
Do not drive with the tailgate or rear
door open. Exhaust fumes may enter
the vehicle.
E97377
LUGGAGE ANCHOR POINTS
Do not exceed the maximum front
and rear axle loads for your vehicle.
See Vehicle identification (page
221).
Heavy loads, when placed in the
passenger compartment, should be
on folded rear seats as shown. See
Rear Seats (page 109).
CAUTIONS
Do not allow items to contact the rear
windows.
Do not use any abrasive materials to
clean the interior of the rear windows.
Do not install stickers or labels to the
interior of the rear windows.
E132901
Lift the flap to access the anchor point.
LUGGAGE COVERS
WARNING
Do not place objects on the luggage
cover.
164
Load Carrying
To install the cargo retention net cassette:
Remove the luggage cover.
Push the sliders on the cassette towards
each other and insert the telescopic bar
into the holes on the sidewall behind the
rear seatbacks.
Ensure that the end caps with the
anti-rotation pin are correctly fitted in the
side trim.
E72969
Pull out the cover and secure it in the
retaining points.
Release it from the retaining points and let
it roll back into the case. Clip the retaining
hook onto the case.
E72970
To remove or install the cover, push either
end of the case inwards.
E78834
Pull up the net and insert the ends of the
bar into the retainers on the roof.
CARGO NETS
Ensure that the bar is pushed forwards into
the narrow section of the retainers.
Luggage retention net
WARNING
WARNING
After installing the cassette, press
the front edge of the luggage cover
back down into its original position
(forwards) to prevent vision out of the rear
screen being obscured.
On Estate vehicles, luggage retention
net anchor points are not fitted
behind the first row seats, but are
fitted behind the second row seats.
165
Load Carrying
Installing behind the front seats
Reinstall the luggage cover.
Remove in the reverse order.
Cargo net
A
B
E86848
1.
Push the ends of the bar on the grille
towards each other and insert them
into the retainers on the roof. Push the
bar forwards into the narrow section
of the retainers.
E78835
A
With retaining rings
B
Without retaining rings
The cargo net can be used to prevent
objects sliding around.
Attach the hooks at each corner of the net
to the four retaining points on the load
floor.
DOG GUARD
CAUTION
E87782
Keep a distance of at least one
centimetre between the dog guard
and the seats in front of it.
2. Attach the dog guard to the lower
anchor points. Do not tighten the
screws.
166
Load Carrying
1.
Push the ends of the bar on the grille
towards each other and insert them
into the retainers on the roof. Push the
bar forwards into the narrow section
of the retainers.
E87783
3. Attach the grille to the lower bar with
the handwheels. Do not tighten the
handwheels.
4. Tighten the screws at the lower anchor
points.
5. Tighten the handwheels.
Installing behind the rear seats
E104424
2. Remove two screws from both the
luggage anchor points. See Luggage
Anchor Points (page 164).
3. Attach the lower bar to the grille with
the handwheels. Do not tighten the
handwheels.
4. Attach the dog guard lower bar to the
luggage anchor points, secure with the
new supplied screws.
5. Tighten the handwheels.
Remove in the reverse order.
E86848
167
Load Carrying
ROOF RACKS AND LOAD
CARRIERS
Note: Before installing the crossbars, clean
the side mounting tracks with water and a
sponge.
Roof rack
Note: Position the crossbars as shown.
A
WARNINGS
If you use a roof rack, the fuel
consumption of your vehicle will be
higher and you may experience
different driving characteristics.
Read and follow the manufacturer’s
instructions when you are fitting a
roof rack.
B
E135136
Do not exceed the maximum
permissible roof load of 75
kilogrammes (165 pounds)
(including the roof rack).
A
515 mm (20 inches)
B
750 mm (30 inches)
Check the security of the roof rack and
tighten its fittings as follows:
•
•
•
Before starting.
After driving 50 kilometres (30 miles).
At 1000 kilometres (600 miles)
intervals.
To reduce fuel consumption, cross rails
should be removed when not in use.
E135137
Note: Adhesive pads are supplied to help
reduce the buffeting noise.
Installing the crossbars
Note: Make sure the surface of the
crossbars is clean before attaching the
adhesive pads.
WARNINGS
Distribute the load evenly over the
loading area and keep the centre of
gravity as low as possible. Secure the
load well to prevent it from slipping. Never
place any loads directly onto the roof
surface.
1.
Remove the crossbars before
entering an automatic car wash.
Note: The side mounting tracks are
designed such that crossbars (for bicycle
carriers, ski carriers etc.) from the Ford
accessories range can be fitted.
168
Remove the backing and attach the
adhesive pads to the crossbars in the
positions shown.
Load Carrying
4 Nm
4
2
4Nm
7
3
E135138
2. Insert the key. Turn the key
anti-clockwise.
3. Remove the cover.
4. Loosen the screws.
A
A
E135139
Note: Make sure there is no gap between
crossbar and rail(A).
6. Install the crossbars.
7. Tighten the screws until you hear a
distinct click.
8. Install the cover. Turn the key clockwise
to lock.
9. Remove the key.
B
Installing a roof box
E135140
E135141
5. Install rubber strips in the positions
shown.
Make sure the adhesive pads are not in
contact with the installation bolt.
169
Towing
Change down a gear before you reach a
steep downhill gradient.
TOWING A TRAILER
WARNINGS
Do not exceed 100 km/h (62 mph).
RETRACTABLE TOW BALL
WARNING
The rear tyre pressures must be
increased by 0.2 bar (3 psi) above
specification. See Technical
Specifications (page 218).
You will hear a warning tone when
the tow ball arm is not in one of the
locked positions. The warning tone
will switch off after 30 seconds. If you do
not hear the tone when moving the tow
ball arm or at system activation, do not
use the tow bar and have it checked by a
properly trained technician.
Do not exceed the maximum gross
train weight stated on the vehicle
identification plate. See Vehicle
identification (page 221).
CAUTION
CAUTION
Do not exceed the maximum
permissible nose weight, i.e. vertical
weight on the tow ball, of 75
kilogrammes (165 pounds).
Only move the tow ball arm with your
hand. Never use your foot or auxiliary
tools as damage to the mechanism
may result.
Note: Not all vehicles are suitable or
approved to have tow bars fitted. Check
with your dealer first.
B
Place loads as low and central to the
axle(s) of the trailer as possible. If you are
towing with an unladen vehicle, the load
in the trailer should be placed toward the
nose, within the maximum nose load, as
this gives the best stability.
A
The stability of the vehicle to trailer
combination is very much dependant on
the quality of the trailer.
E139283
A 13-pin trailer socket A is provided
underneath the rear bumper next to the
tow ball arm B.
In high altitude regions above 1000 metres
(3281 feet), the stipulated maximum
permitted gross train weight must be
reduced by 10% for every additional 1000
metres (3281 feet).
Releasing the tow ball arm
CAUTION
Steep gradients
Do not touch the tow ball arm during
the release process.
WARNING
The overrun brake on a trailer is not
controlled by ABS.
170
Towing
Note: If the release process is interrupted,
for example an obstacle in the way or loss
of power supply, the system will need to be
reset. To reset the system, repeat the
release process.
Note: The lamp in the switch illuminates
when the system is activated.
The following conditions must be met
before releasing the tow ball arm:
•
•
•
•
The luggage compartment lid must be
open.
The ignition must be switched off.
No plug must be attached to the 13-pin
trailer socket.
E139284
The tow ball arm automatically swivels
into the lowered position.
If the tow ball arm fails to release, press
the button again for 15 seconds.
The battery voltage must be greater
than 11 volts.
WARNING
If it still fails to release, do not use
the tow bar and have it checked by
a properly trained technician.
Swivelling the tow ball arm out
E132909
1.
Press the button to activate the
system.
2. Press the button again within four
seconds to release the tow ball arm.
E75179
Move the tow ball arm to the operating
position. The tow ball arm automatically
locks in the operating position. The locking
process is clearly audible and the warning
tone will stop.
171
Towing
Swivelling the tow ball arm in
Fault conditions
If the tow ball arm release button is
illuminated or you hear a warning tone
when the ignition switch is in position II,
repeat the release process.
CAUTION
Before swivelling the tow ball arm in,
always unhitch the trailer or dismantle
load carriers and their attachments.
Dismantle attachments for tracking
stabilisation. Remove the plug for the
trailer power supply and the adapter from
the socket. Failure to do so may result in
damage to the bumper.
1.
If you pull on the tow ball arm during the
release process, the system will stop
moving to prevent an overload condition.
To reset the system, press the release
button for 15 seconds.
Driving with a trailer
Release the tow ball arm. See releasing
the tow ball arm.
WARNINGS
In the event of a vehicle breakdown,
disconnect the trailer before towing
the vehicle.
If any of the conditions below cannot
be met, do not use the tow bar and
have it checked by a properly trained
technician.
Before starting your journey, make sure
that the tow ball arm is properly locked.
Check that:
E139284
2. The tow ball arm automatically swivels
into the lowered position.
•
•
there is no warning tone when the
locking procedure has been completed
the tow ball arm is locked. It must not
move when jerked.
Maintenance
CAUTIONS
The towing hitch and control unit are
maintenance-free. Do not grease or
oil them.
Only the manufacturer should carry
out repairs or dismantle the towing
hitch.
E75177
3. Move the tow ball arm to the stop in
the stowed position. The tow ball arm
automatically locks in the stowed
position. The locking process is clearly
audible and the warning tone will stop.
If you use a high pressure spray to
wash your vehicle, do not direct the
spray onto the swivel joint of the tow
ball arm.
172
Towing
Unlocking the tow ball arm
mechanism
TOW BALL
WARNINGS
When not in use, always transport
the tow ball arm securely fastened
in the luggage compartment.
3
Take special care when fitting the
tow ball arm as the safety of the
vehicle and the trailer depends on
1
this.
Do not use any tools for mounting or
dismounting the tow ball arm. Do not
modify the trailer coupling. Do not
disassemble or repair the tow ball arm.
2
E71329
1.
Remove the protecting cap (1). Insert
the key and turn it clockwise to unlock
(2).
2. Hold the tow ball arm. Pull the
handwheel out and turn it clockwise
until it clicks (3).
3. The red mark on the handwheel must
align with the green mark on the tow
ball.
4. Release the handwheel. The tow ball
arm is unlocked.
E71328
A 13-pin trailer socket and the tow ball arm
seat are provided underneath the rear
bumper. Turn the trailer socket down
through 90 degrees until it engages in the
end position.
173
Towing
Inserting the tow ball arm
Driving with a trailer
A
1
B
E71331
WARNING
If any of the below conditions cannot
be met, do not use the tow bar and
have it checked by a properly trained
technician.
2
Before starting your journey, make sure
that the tow ball arm is properly locked.
Check that:
E71330
WARNING
•
•
The tow ball arm may only be
inserted when completely unlocked.
•
•
1. Pull out the plug.
2. Insert the tow ball arm vertically and
press it upwards until it engages (1).
Do not hold your hand near the
handwheel.
3. The green mark on the handwheel
must align with the green mark on the
tow ball.
4. To lock, turn the key anti-clockwise and
remove the key (2).
5. Pull the protecting cap from the key
bow and press it onto the lock.
174
the green marks are aligned
the handwheel (A) is correctly fitted
to the tow ball arm
you have removed the key (B)
the tow ball arm is securely positioned.
It must not move when jerked.
Towing
Removing the tow ball arm
Driving without a trailer
1
3
2
E94771
1. Remove the tow ball arm.
2. Insert the plug into its seat (1).
1
E71332
WARNING
1. Unhitch the trailer.
2. Remove the protecting cap. Press the
cap into the key bow. Insert the key and
unlock (1).
3. Hold the tow ball arm. Pull the
handwheel out, turn it clockwise
against the stop (2) and remove the
tow ball arm (3).
4. Release the handwheel.
Never unlock the tow ball arm with
the trailer attached.
Maintenance
WARNING
Remove the tow ball arm and
protect the seat with the plug before
steam cleaning your vehicle.
When unlocked in this way, the tow ball
arm can be reinserted at any time.
Keep the system clean. Periodically
lubricate bearings, sliding surfaces, and
locking balls with resin-free grease or oil
and the lock with graphite.
In case of loss, replacement keys are
available from the manufacturer by stating
the number on the lock cylinder.
175
Driving Hints
In an emergency, the vehicle can be driven
through water to a maximum depth of 200
millimetres (8 inches) and at a maximum
speed of 10 km/h (6 mph). Extra caution
should be exercised when driving through
flowing water.
RUNNING-IN
Tyres
WARNING
New tyres need to be run-in for
approximately 500 kilometres (300
miles). During this time, you may
experience different driving characteristics.
When driving in water, maintain a low
speed and do not stop the vehicle. After
driving through water, and as soon as it is
safe to do so:
• Depress the brake pedal lightly and
check that full brake function is
achieved.
• Check that the horn works.
• Check that the vehicle's lights are fully
operational.
• Check the power assistance
of the steering system.
Brakes and clutch
WARNING
Avoid heavy use of the brakes and
clutch if possible for the first 150
kilometres (100 miles) in town and
for the first 1500 kilometres (1000 miles)
on motorways.
Engine
CAUTION
Avoid driving too fast during the first
1500 kilometres (1000 miles). Vary
your speed frequently and change up
through the gears early. Do not labour the
engine.
COLD WEATHER
PRECAUTIONS
The functional operation of some
components and systems can be affected
at temperatures below -30°C (-22°F).
DRIVING THROUGH WATER
Driving through water
CAUTIONS
Drive through water in an emergency
only, and not as part of normal driving.
Engine damage can occur if water
enters the air filter.
176
Roadside Emergencies
FIRST AID KIT
Space is provided in the luggage
compartment.
WARNING TRIANGLE
Space is provided in the luggage
compartment.
177
Fuses
Load compartment fuse box
FUSE BOX LOCATIONS
4-door
Engine compartment fuse box
This fuse box is located in the engine
compartment See Maintenance (page
190).
Passenger compartment fuse box
E135336
5-door
E130170
E135337
E130171
1.
Pinch the retaining clips to release the
cover.
2. Lower the fuse box cover and pull it
towards you.
Install in the reverse order.
178
Fuses
Estate
CHANGING A FUSE
WARNINGS
Do not modify the electrical system
of your vehicle in any way. Have
repairs to the electrical system and
the replacement of relays and high current
fuses carried out by a properly trained
technician.
Switch the ignition and all electrical
equipment off before touching or
attempting to change a fuse.
CAUTION
E135338
Fit a replacement fuse with the same
rating as the one you have removed.
Note: You can identify a blown fuse by a
break in the filament.
Note: All fuses, except high current fuses,
are a push fit.
Note: A fuse puller is located in the engine
compartment fuse box.
179
Fuses
FUSE SPECIFICATION CHART
Engine compartment fuse box
E129925
Fuse
Ampere
rating
7
40
ABS pump, Electronic Stability Program (ESP) pump
8
30
Electronic Stability Program (ESP) valve
9
30
Heated rear window
10
40
Heater blower
11
30
Start-stop module
Circuits protected
12
30
Engine management systems
13
30
Starter relay
14
40
Heated windscreen (right-hand side)
15
25
Transmission control module
180
Fuses
Fuse
Ampere
rating
16
40
Heated windscreen (left-hand side)
17
20
Auxiliary heater
18
20
Windscreen wipers
Circuits protected
19
5
ABS, Electronic Stability Program (ESP) module
20
15
Horn
21
5
Brake lamp switch
22
15
Battery monitoring system
23
5
Relay coils, lighting control switch module
24
20
Rear power outlet
25
10
Electric exterior mirrors
26
15
Transmission control module
27
15
Air conditioning clutch
28
5
Adaptive cruise control
29
20
30
5
Powertrain control module (PCM)
31
-
Not used
32
10
EGR Valve, swirl control valves, HEGO sensor (engine
management)
Headlamp washer
33
10
Engine control valves
34
10
Injectors
35
5
Active grille shutter (Petrol engine)
35
15
Active grille shutter and filter heater (Diesel engine)
36
10
Powertrain control module (PCM)
37
-
Not used
38
15
Powertrain control module (PCM), transmission control
module
39
5
Headlamp control module
181
Fuses
Fuse
Ampere
rating
40
5
41
20
Body Control Module
42
15
Rear window wiper
Circuits protected
Electric power assisted steering
43
15
Headlamp levelling
44
5
Adaptive cruise control
45
10
Heated washer jets
46
25
Electric windows (front)
47
7.5
Heated exterior mirrors
48
15
Vaporizer
182
Fuses
Passenger compartment fuse box
E129926
Fuse
Ampere
rating
56
20
Circuits protected
Fuel pump supply
183
Fuses
Fuse
Ampere
rating
57
-
Not used
58
-
Not used
59
5
Passive anti theft system (PATS) supply
60
10
Interior lamps, driver's door switch pack, glove box,
ambient lighting, electric sunroof
Cigar lighter, rear power outlet
Circuits protected
61
20
62
5
Rain sensor module, humidity sensor, auto-dimming mirror
63
10
Adaptive cruise control
64
-
65
10
Luggage compartment lid release
66
20
Driver's door lock, double locking
67
7.5
Information and entertainment display, GPS, BVC
68
15
Steering column lock
69
5
Instrument cluster
70
20
Central locking
71
10
Air conditioning
72
7.5
Steering wheel control module
73
5
Battery back-up sounder (alarm system), onboard
diagnostics system
74
15
Main beam
Not used
75
15
Front fog lamps
76
10
Reversing lamp
77
20
Washer pump
78
5
Ignition switch or start button
79
15
Radio, hazard and door lock buttons
80
20
Electric sunroof
81
5
Interior motion sensor, RF receiver
184
Fuses
Fuse
Ampere
rating
82
20
Washer pump ground
83
20
Central locking ground
84
20
Driver's door lock and double locking ground
85
7.5
Climate control heater, passenger airbag deactivation
switch, heated seats switch, auxiliary heater, manual air
conditioning heater module
86
10
Restraint system, passenger airbag deactivation system
Circuits protected
87
-
Not used
88
-
Not used
89
-
Not used
Load compartment fuse box
E129927
Fuse
Ampere
rating
1
-
Circuits protected
Not used
2
10
Keyless vehicle module
3
5
Keyless vehicle door handles
4
25
Door module (left-hand front) (electric windows, central
locking, electric folding mirrors, heated exterior mirrors)
185
Fuses
Fuse
Ampere
rating
Circuits protected
5
25
Door module (right-hand front) (electric windows, central
locking, electric folding mirrors, heated exterior mirrors)
6
25
Door module (left-hand rear) (electric windows)
7
25
Door module (right-hand rear) (electric windows)
8
10
Alarm system
Electric driver's seat
9
25
10
-
Not used
11
-
Not used
12
10
Air conditioning module (with start-stop module)
13
5
Instrument cluster (with start-stop module)
14
7.5
Information and entertainment display, GPS module (with
start-stop module)
15
15
Audio unit, audio unit control panel (with start-stop
module)
16
-
Not used
17
-
Not used
18
-
Not used
19
-
Not used
20
-
Not used
21
-
Not used
22
-
Not used
23
-
Not used
24
-
Not used
25
-
Not used
26
40
27
-
Not used
28
-
Not used
Trailer module
186
Fuses
Fuse
Ampere
rating
Circuits protected
29
5
Blind spot monitor, lane keeping aid, active city stop, rear
view camera (without start-stop module)
30
5
Parking aid module
31
-
Not used
32
-
Not used
33
-
Not used
34
15
Heated driver's seat
35
15
Heated front passenger seat
36
-
Not used
37
5
Electric sunroof
38
-
Not used
39
-
Not used
40
-
Not used
41
5
Retractable tow ball
42
-
Not used
43
-
Not used
44
-
Not used
45
-
Not used
46
10
Blind spot monitor, lane keeping aid, rear view camera
(with start-stop module)
187
Vehicle recovery
Rear towing eye
TOWING POINTS
Towing eye location
The screw-in towing eye is located in the
spare wheel well.
The towing eye must always be carried in
the vehicle.
Installing the towing eye
CAUTION
The screw-in towing eye has a
left-hand thread. Turn it
anti-clockwise to install it. Make sure
that the towing eye is fully tightened.
Note: On vehicles with a tow bar, the
towing eye cannot be installed at the rear
of the vehicle. Use the tow bar to tow a
vehicle.
E78368
Insert a suitable object into the hole on the
underside of the cover and prise off the
cover.
Front towing eye
Install the towing eye.
TOWING THE VEHICLE ON
FOUR WHEELS
All vehicles
WARNINGS
Switch the ignition on when your
vehicle is being towed. The steering
lock will engage and the direction
indicators and brake lamps will not work
if you do not.
The brake and steering assistance
will not operate unless the engine is
running. Press the brake pedal harder
and allow for increased stopping distances
and heavier steering.
E78367
188
Vehicle recovery
CAUTIONS
Too much tension in the tow rope
could cause damage to your vehicle
or the vehicle that is towing.
Select neutral when your vehicle is
being towed.
In the event of a breakdown or
mechanical failure do not use
individual axle carriers. Your vehicle
must be recovered with either ALL wheels
on the ground or transported with ALL
wheels lifted clear of the ground on a level
platform.
Drive off slowly and smoothly without
jerking the vehicle that is towing.
Vehicles with automatic
transmission
CAUTIONS
If a speed of 20 km/h (12 mph) and a
distance of 20 kilometres (12 miles)
is to be exceeded ALL wheels must
be lifted clear of the ground.
It is recommended not to tow with the
drive wheels on the ground. However,
if it is required to move the vehicle
from a dangerous location, do not tow your
vehicle faster than 20 km/h (12 mph) or
further than 20 kilometres (12 miles).
Do not tow your vehicle backwards.
In the event of a mechanical failure of
the transmission do not use individual
axle carriers. ALL wheels must be
lifted clear of the ground on a level
platform.
Do not tow your vehicle if the ambient
temperature is below 0°C (32°F).
189
Maintenance
Check when refuelling
GENERAL INFORMATION
•
Have your vehicle serviced regularly to help
maintain its roadworthiness and resale
value. There is a large network of Ford
Authorised Repairers that are there to help
you with their professional servicing
expertise. We believe that their specially
trained technicians are best qualified to
service your vehicle properly and expertly.
They are supported by a wide range of
highly specialised tools developed
specifically for servicing your vehicle.
•
•
•
•
In addition to regular servicing, we
recommend that you carry out the
following additional checks.
Engine oil level. See Engine Oil Check
(page 198).
Brake fluid level. See Brake and
Clutch Fluid Check (page 200).
Washer fluid level. See Washer Fluid
Check (page 200).
Tyre pressures (when cold). See
Technical Specifications (page 218).
Tyre condition. See Wheels and Tyres
(page 208).
Monthly checks
•
WARNINGS
Switch the ignition off before
touching or attempting adjustment
of any kind.
•
•
•
•
•
Do not touch the electronic ignition
system parts after you have switched
the ignition on or when the engine is
running. The system operates at high
voltage.
Engine coolant level (engine cold). See
Engine Coolant Check (page 199).
Pipes, hoses and reservoirs for leaks.
Air conditioning operation.
Parking brake operation.
Horn operation.
Tightness of wheel nuts. See
Technical Specifications (page 218).
OPENING AND CLOSING THE
BONNET
Keep your hands and clothing clear
of the engine cooling fan. Under
certain conditions, the fan may
continue to run for several minutes after
you have switched the engine off.
Opening the bonnet
CAUTION
When carrying out maintenance
checks, make sure that filler caps are
fitted securely.
Daily checks
•
•
•
Exterior lamps.
Interior lamps.
Warning lamps and indicators.
E73698
190
Maintenance
E133239
E87786
Move the yellow catch to the right.
Open the bonnet and support it with the
strut.
Closing the bonnet
WARNING
Make sure that the bonnet is closed
properly.
Lower the bonnet and allow it to drop from
under its own weight for the last 20 – 30
centimetres (8 - 11 inches).
191
Maintenance
UNDER BONNET OVERVIEW - 1.6L DURATEC-16V TI-VCT (SIGMA)
A
B
C
I
D
E
H
F
G
E130030
*
A
Engine coolant reservoir : See Engine Coolant Check (page 199).
B
Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch
Fluid Check (page 200).
C
Engine oil filler cap : See Engine Oil Check (page 198).
D
Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid
Check (page 200).
E
Battery: See Vehicle battery (page 206).
F
Engine compartment fuse box: See Fuses (page 178).
G
Air cleaner: No maintenance necessary.
H
Engine oil dipstick : See Engine Oil Check (page 198).
I
Screen washer fluid reservoir : See Washer Fluid Check (page 200).
*
*
*
*
*
*
For easy identification, filler caps and the engine oil dipstick are marked in colour.
192
Maintenance
UNDER BONNET OVERVIEW - 1.6L ECOBOOST SCTI (SIGMA)
B
A
I
H
C
G
D
E
F
E132729
A
Brake and clutch fluid reservoir (right-hand drive). See Brake and Clutch Fluid
Check (page 200).
B
Engine oil filler cap . See Engine Oil Check (page 198).
C
Brake and clutch fluid reservoir (left-hand drive). See Brake and Clutch Fluid
Check (page 200).
D
Battery. See Vehicle battery (page 206).
E
Engine compartment fuse box. See Fuses (page 178).
F
Air cleaner. No maintenance necessary.
G
Engine oil dipstick . See Engine Oil Check (page 198).
1
1
193
Maintenance
H
Screen washer fluid reservoir. See Washer Fluid Check (page 200).
I
Engine coolant reservoir. See Engine Coolant Check (page 199).
1
The filler caps and the engine oil dipstick are coloured for easy identification.
UNDER BONNET OVERVIEW - 1.6L DURATORQ-TDCI (DV) DIESEL
A
I
B
C
D
E
F
H
G
E130031
*
A
Engine coolant reservoir : See Engine Coolant Check (page 199).
B
Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch
Fluid Check (page 200).
C
Engine oil filler cap : See Engine Oil Check (page 198).
D
Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid
Check (page 200).
E
Battery: See Vehicle battery (page 206).
*
*
*
194
Maintenance
F
Engine compartment fuse box: See Fuses (page 178).
G
Air cleaner: No maintenance necessary.
H
Engine oil dipstick : See Engine Oil Check (page 198).
I
Screen washer fluid reservoir : See Washer Fluid Check (page 200).
*
*
*
For easy identification, filler caps and the engine oil dipstick are marked in colour.
UNDER BONNET OVERVIEW - 2.0L DURATEC-HE (MI4)
A
I
B
C
H
D
E
G
E139960
195
F
Maintenance
*
A
Engine coolant reservoir : See Engine Coolant Check (page 199).
B
Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch
Fluid Check (page 200).
C
Engine oil filler cap : See Engine Oil Check (page 198).
D
Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid
Check (page 200).
E
Battery: See Vehicle battery (page 206).
*
*
*
F
Engine compartment fuse box: See Fuses (page 178).
G
Air cleaner: No maintenance necessary.
H
Engine oil dipstick : See Engine Oil Check (page 198).
I
Screen washer fluid reservoir : See Washer Fluid Check (page 200).
*
*
*
For easy identification, filler caps and the engine oil dipstick are marked in colour.
196
Maintenance
UNDER BONNET OVERVIEW - 2.0L DURATORQ-TDCI (DW) DIESEL
A
I
B
C
D
E
F
H
G
E130032
*
A
Engine coolant reservoir : See Engine Coolant Check (page 199).
B
Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch
Fluid Check (page 200).
C
Engine oil dipstick : See Engine Oil Check (page 198).
D
Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid
Check (page 200).
E
Battery: See Vehicle battery (page 206).
*
*
*
F
Engine compartment fuse box: See Fuses (page 178).
G
Air cleaner: No maintenance necessary.
H
Engine oil filler cap : See Engine Oil Check (page 198).
I
Screen washer fluid reservoir : See Washer Fluid Check (page 200).
*
*
*
For easy identification, filler caps and the engine oil dipstick are marked in colour.
197
Maintenance
ENGINE OIL DIPSTICK - 2.0L
DURATEC-HE (MI4)
ENGINE OIL DIPSTICK - 1.6L
DURATEC-16V TI-VCT (SIGMA)
A
B
A
E95540
B
E134040
A
MIN
A
MIN
B
MAX
B
MAX
ENGINE OIL DIPSTICK - 1.6L
ECOBOOST SCTI (SIGMA)
A
ENGINE OIL DIPSTICK - 1.6L
DURATORQ-TDCI (DV)
DIESEL/2.0L DURATORQ-TDCI
(DW) DIESEL
B
A
E134114
B
E95543
A
MIN
A
MIN
B
MAX
B
MAX
ENGINE OIL CHECK
CAUTION
Do not use oil additives or other
engine treatments. Under certain
conditions, they could damage the
engine.
198
Maintenance
Note: The oil consumption of new engines
reaches its normal level after approximately
5000 kilometres (3000 miles).
ENGINE COOLANT CHECK
Checking the coolant level
Checking the oil level
WARNING
Do not allow the fluid to touch your
skin or eyes. If this happens, rinse the
affected areas immediately with
plenty of water and contact your doctor.
CAUTION
Make sure that the level is between
the MIN and the MAX marks.
Note: Check the level before starting the
engine.
CAUTION
Make sure that the level is between
the MIN and the MAX marks.
Note: Make sure that your vehicle is on level
ground.
Note: Oil expands when it is hot. The level
may therefore extend a few millimetres
beyond the MAX mark.
Note: Coolant expands when it is hot. The
level may therefore extend beyond the MAX
mark.
Remove the dipstick and wipe it with a
clean, lint free cloth. Replace the dipstick
and remove it again to check the oil level.
If the level is at the MIN mark, top up
immediately.
Topping up
If the level is at the MIN mark, top up
immediately.
WARNINGS
Only top up when the engine is cold.
If the engine is hot, wait 10 minutes
for the engine to cool down.
Topping up
WARNINGS
Only top up when the engine is cold.
If the engine is hot, wait 10 minutes
for the engine to cool down.
Do not remove the filler cap when
the engine is running.
Do not remove the filler cap when
the engine is hot. Wait for the engine
to cool down.
Do not remove the filler cap when
the engine is running.
Undiluted coolant is flammable and
may ignite if spilt on a hot exhaust.
Remove the filler cap.
CAUTION
Do not top up further than the MAX
mark.
CAUTIONS
In an emergency, you can add just
water to the cooling system to reach
a vehicle service station. Have the
system checked by a properly trained
technician as soon as possible.
Top up with fluid that meets the Ford
specification. See Technical
Specifications (page 201).
Replace the filler cap. Turn it until you feel
a strong resistance.
199
Maintenance
CAUTIONS
Prolonged use of incorrect dilution of
the coolant can cause engine damage
from corrosion, overheating or
freezing.
WARNINGS
If the level is at the MIN mark, have
the system checked by a properly
trained technician as soon as
possible.
Unscrew the cap slowly. Any pressure will
escape slowly as you unscrew the cap.
Note: Keep brake fluid clean and dry.
Contamination with dirt, water, petroleum
products or other materials may result in
brake system damage and possible failure.
CAUTION
Do not top up further than the MAX
mark.
Note: The brake and the clutch systems are
supplied from the same reservoir.
Top up with fluid that meets the Ford
specification. See Technical
Specifications (page 201).
Top up with a 50/50 mixture of coolant
and water using fluid that meets the Ford
specification. See Technical
Specifications (page 201).
WASHER FLUID CHECK
BRAKE AND CLUTCH FLUID
CHECK
Note: The front and rear washer systems
are supplied from the same reservoir.
When topping up, use a mixture of washer
fluid and water to help prevent freezing in
cold weather and improve the cleaning
capability. We recommend that you use
only high quality washer fluid.
WARNINGS
Use of any fluid other than the
recommended brake fluid may
reduce brake efficiency and not meet
Ford's performance standards.
For information on fluid dilution, refer to
the product instructions.
Do not allow the fluid to touch your
skin or eyes. If this happens, rinse the
affected areas immediately with
plenty of water and contact your doctor.
200
Maintenance
TECHNICAL SPECIFICATIONS
Vehicle fluids
CAUTION
Do not use fluids which do not meet the specifications or requirements defined. Use
of unsuitable fluids may lead to damage which is not covered by your Warranty.
Item
Specification
Engine oil - petrol and diesel
engines
Recommended fluid
WSS-M2C913-C
Castrol or Ford Engine Oil
Alternative engine oil petrol engines only
WSS-M2C925-B
Castrol Engine Oil
Antifreeze
WSS-M97B44-D
Motorcraft SuperPlus Antifreeze
Brake fluid
WSS-M6C65-A2 or ISO
4925 Class 6
Motorcraft or Ford DOT 4 LV
High Performance Brake
Fluid
Your engine has been designed to be used with Castrol and Ford Engine Oil, which gives
a fuel economy benefit whilst maintaining the durability of your engine.
For petrol engines only, Ford and Castrol have developed a low friction SAE-5W-20 oil
which offers further fuel economy benefits over the standard SAE-5W-30 oil. If this oil
is not available, we recommend that you service with oil to specification WSS-M2C913-C.
Topping up the oil: If you are unable to find an oil that meets the specification defined
by WSS-M2C913-C or WSS-M2C925-B (petrol engines only), you must use SAE 5W-30
that meets the specification defined by ACEA A5/B5.
Using topping up oils other than the one specified can result in longer engine cranking
periods, reduced engine performance, reduced fuel economy and increased emission
levels.
Castrol engine oil recommended.
E115472
201
Maintenance
Capacities
Variant
Item
Capacity in Litres (gallons)
Vehicles with a petrol
engine
Fuel tank
55 (12.1)
1.6L Duratorq-TDCi - DV
Fuel tank
53 (11.7)
2.0L Duratorq-TDCi - DW
Fuel tank
60 (13.2)
All
Windscreen washer system
- with headlamp washers
4.5 (1)
All
Windscreen washer system
- without headlamp
washers
3 (0.7)
1.6L Duratec-16V Ti-VCT Sigma
Engine oil - with filter
1.6L Duratec-16V Ti-VCT Sigma
Engine oil - without filter
1.6L Duratec-16V Ti-VCT Sigma
Cooling system
1.6L EcoBoost - Sigma
Engine oil - with filter
1.6L EcoBoost - Sigma
Engine oil - without filter
4.1 (0.9)
3.75 (0.8)
approx. 5.8 (1.3)
4.1 (0.9)
3.75 (0.8)
1.6L EcoBoost - Sigma
Cooling system
2.0L Duratec-HE - MI4
Engine oil - with filter
2.0L Duratec-HE - MI4
Engine oil - without filter
2.0L Duratec-HE - MI4
Cooling system
1.6L Duratorq-TDCi - DV
Engine oil - with filter
3.8 (0.8)
1.6L Duratorq-TDCi - DV
Engine oil - without filter
3.5 (0.8)
1.6L Duratorq-TDCi - DV
Cooling system
2.0L Duratorq-TDCi - DW
Engine oil - with filter
5.7 (1.3)
2.0L Duratorq-TDCi - DW
Engine oil - without filter
5.4 (1.2)
2.0L Duratorq-TDCi - DW
Cooling system
202
approx. 6.3 (1.4)
4.3 (1)
3.9 (0.9)
approx. 6.5 (1.4)
approx. 7.3 (1.6)
approx. 8.5 (1.9)
Maintenance
Engine oil top up capacities
Engine
Capacity in litres (gallons)
1.6L Duratec-16V Ti-VCT - Sigma
0.8 (0.2)
1.6L EcoBoost - Sigma
0.8 (0.2)
2.0L Duratec-HE - MI4
0.9 (0.2)
1.6L Duratorq-TDCi - DV
1.6 (0.4)
2.0L Duratorq-TDCi - DW
1.8 (0.4)
203
Vehicle Care
Cleaning the chrome trim
CLEANING THE EXTERIOR
CAUTION
WARNING
Do not use abrasives or chemical
solvents. Use soapy water.
If you use a car wash with a waxing
cycle, make sure that you remove the
wax from the windscreen.
Body paintwork preservation
CAUTIONS
Prior to using a car wash facility check
the suitability of it for your vehicle.
CAUTIONS
Do not polish your vehicle in strong
sunshine.
Some car wash installations use
water at high pressure. This could
damage certain parts of your vehicle.
Do not allow polish to touch plastic
surfaces. It could be difficult to
remove.
Remove the aerial before using an
automatic car wash.
Do not apply polish to the windscreen
or rear window. This could cause the
wipers to become noisy and they may
not clear the window properly.
Switch the heater blower off to
prevent contamination of the fresh air
filter.
We recommend that you wax the
paintwork once or twice a year.
We recommend that you wash your vehicle
with a sponge and lukewarm water
containing a car shampoo.
CLEANING THE INTERIOR
Cleaning the headlamps
Seat belts
CAUTIONS
Do not scrape the headlamp lenses
or use abrasives, alcoholic solvents or
chemical solvents to clean them.
WARNINGS
Do not use abrasives, or chemical
solvents to clean them.
Do not wipe the headlamps when
they are dry.
Do not allow moisture to penetrate
the seat belt retractor mechanism.
Clean the seat belts with interior cleaner
or water applied with a soft sponge. Let
the seat belts dry naturally, away from
artificial heat.
Cleaning the rear window
CAUTION
Do not scrape the inside of the rear
window or use abrasives or chemical
solvents to clean it.
Use a clean, lint free cloth or a damp
chamois leather to clean the inside of the
rear window.
204
Vehicle Care
Instrument cluster screens, LCD
screens, radio screens
WARNING
Do not use abrasives, alcoholic
solvents or chemical solvents to
clean them.
Rear windows
CAUTIONS
Do not use any abrasive materials to
clean the interior of the rear windows.
Do not install stickers or labels to the
interior of the rear windows.
REPAIRING MINOR PAINT
DAMAGE
CAUTION
Remove apparently harmless looking
substances from the paintwork
immediately (e.g. bird droppings, tree
resins, insect remains, tar spots, road salt
and industrial fall out).
You should repair paintwork damage
caused by stones from the road or minor
scratches as soon as possible. A choice of
products is available from your Ford
Dealer. Read and follow the
manufacturer’s instructions.
205
Vehicle battery
To connect the booster cables
JUMP-STARTING THE VEHICLE
WARNING
Do not use fuel lines, engine rocker
covers or the intake manifold as
grounding points.
A
CAUTIONS
Connect batteries with only the same
nominal voltage.
Always use booster cables with
insulated clamps and adequate size
cable.
C
D
Do not disconnect the battery from
the vehicle’s electrical system.
B
E102925
1.
A
Flat battery vehicle
B
Booster battery vehicle
C
Positive connection cable
D
Negative connection cable
Position the vehicles so that they do
not touch one another.
2. Switch off the engine and any electrical
equipment.
3. Connect the positive (+) terminal of
vehicle B with the positive (+) terminal
of vehicle A (cable C).
4. Connect the negative (-) terminal of
vehicle B to the ground connection of
vehicle A (cable D). See Battery
connection points (page 207).
206
Vehicle battery
BATTERY CONNECTION
POINTS
CAUTIONS
Do not connect to the negative (–)
terminal of the flat battery.
CAUTION
Make sure that the cables are clear of
any moving parts and fuel delivery
system parts.
Do not connect to the negative (–)
terminal of the flat battery.
To start the engine
1.
Run the engine of vehicle B at
moderately high speed.
2. Start the engine of vehicle A.
3. Run both vehicles for a minimum of
three minutes before disconnecting the
cables.
CAUTION
Do not switch on the headlamps when
disconnecting the cables. The peak
voltage could blow the bulbs.
E130431
Disconnect the cables in the reverse order.
The ground connection point is located to
the right of the battery near the engine
compartment fuse box.
CHANGING THE VEHICLE
BATTERY
CAUTION
For vehicles with Start-stop the
battery requirement is different. It
must be replaced by one of exactly
the same specification as the original.
Note: Where applicable, the audio system
must be reprogrammed with the keycode.
The battery is located in the engine
compartment. See Maintenance (page
190).
207
Wheels and Tyres
Refer to the following information before
changing the road wheel.
GENERAL INFORMATION
CAUTIONS
Use only approved wheel and tyre
sizes. Using other sizes could damage
the vehicle and will make the National
Type Approval invalid.
WARNINGS
Drive the shortest possible distances.
Do not fit more than one spare wheel
on your vehicle at any one time.
If you change the diameter of the tyres
from that fitted at the factory, the
speedometer may not display the
correct speed. Take the vehicle to your
dealer to have the engine management
system reprogrammed.
Do not carry out any tyre repairs on
a spare wheel.
Do not drive through an automatic
car wash.
If you are unsure what type of spare
wheel you have do not exceed 80
km/h (50 mph).
If you intend to change the size of the
wheels from that fitted at the factory,
check the suitability with your dealer.
Only fit snow chains to specified
tyres. See Technical
Specifications (page 218).
Note: Check your tyre pressures regularly
to optimise fuel economy.
A decal with tyre pressure data is located
in the driver’s door opening at the B-pillar.
CAUTION
Check and set the tyre pressure at the
ambient temperature in which you are
intending to drive the vehicle and when the
tyres are cold.
The ground clearance of your vehicle
may be reduced. Take care when
parking next to a kerb.
CHANGING A ROAD WHEEL
Note: Your vehicle may exhibit some
unusual driving characteristics.
Locking wheel nuts
Vehicle jack
You can obtain a replacement locking
wheel nut key and replacement locking
wheel nuts from your dealer using the
reference number certificate.
WARNINGS
The vehicle jack supplied with your
vehicle should only be used when
changing a wheel in emergency
situations.
Vehicles with a spare wheel
Before using the vehicle jack, check
that it is not damaged or deformed
and that the thread is lubricated and
free from foreign matter.
If the spare wheel is exactly the same type
and size as the other fitted road wheels,
you can replace the existing road wheel
with the spare wheel and continue to drive
in the normal manner.
Never place anything between the
jack and the ground, or the jack and
the vehicle.
If the spare wheel is different to the other
road wheels, it will carry a yellow label with
the appropriate speed limit.
208
Wheels and Tyres
Note: Vehicles with a tyre repair kit are not
equipped with a vehicle jack or a wheel
brace.
Vehicles without tyre repair kit
Your vehicle jack, wheel brace, screw-in
towing eye and wheel trim remover are
located in the spare wheel well.
It is recommended to use a workshop type
hydraulic jack for changing between
summer and winter tyres.
Jacking and lifting points
Note: Use a jack with a minimum lifting
capacity of 1.5 tonnes and a lifting plate with
a minimum diameter of 80 millimetres (3.1
inches).
CAUTION
Use only the specified jacking points.
If you use other positions, you may
damage the body, steering,
suspension, engine, braking system or the
fuel lines.
A
B
E92658
A
Emergency use only
B
Maintenance
209
Wheels and Tyres
Assembling the wheel brace
A
Type one
WARNING
When returning the wheel brace
extension to its original position, take
care not to get your fingers caught.
Note: Make sure that the wheel brace is
fully extended.
E93302
Small arrow-shaped marks on the sills A
show the location of the jacking points.
E122546
Extend the wheel brace.
Type two
CAUTION
The screw-in towing eye has a
left-hand thread. Turn it
anti-clockwise to install it. Make sure
that the towing eye is fully tightened.
E92932
E122502
Insert the screw-in towing eye into the
wheel brace.
E93020
210
Wheels and Tyres
Removing the wheel trim
WARNINGS
If your vehicle has a manual
transmission, select first or reverse
gear. If it has an automatic
transmission, select park.
Type one
Insert the flat end of the wheel brace
between the rim and the trim and carefully
remove the trim.
Have the passengers leave the
vehicle.
Type two
Secure the diagonally opposite
wheel with an appropriate block or
wheel chock.
Make sure that the arrows on
directional tyres point in the direction
of rotation when the vehicle is
moving forwards. If you have to fit a spare
wheel with the arrows pointing in the
opposite direction, have the tyre refitted
in the correct direction by a properly
trained technician.
1
2
Do not work underneath the vehicle
when it is supported only by a jack.
Make sure that the jack is vertical to
the jacking point and the base is flat
on the ground.
E122314
CAUTION
1. Insert the wheel trim remover.
2. Remove the wheel trim.
Note: Make sure that you pull the wheel
trim remover at right angles to the trim.
Do not lay alloy wheels face down on
the ground, this will damage the paint.
Note: The spare wheel is located under the
floor cover in the luggage compartment.
Removing a road wheel
1.
WARNINGS
Park your vehicle in such a position
that neither the traffic nor you are
hindered or endangered.
Set up a warning triangle.
Make sure that the vehicle is on firm,
level ground with the wheels pointing
straight ahead.
Switch off the ignition and apply the
parking brake.
211
Install the locking wheel nut key.
Wheels and Tyres
CAUTION
Do not install alloy wheels using
wheel nuts designed for use with steel
wheels.
Note: The wheel nuts of alloy wheels and
spoked steel wheels can also be used for
the steel spare wheel for a short time
(maximum two weeks).
1
Note: Make sure the wheel and hub contact
surfaces are free from foreign matter.
Note: Make sure that the cones on the
wheel nuts are against the wheel.
1. Install the wheel.
2. Install the wheel nuts finger tight.
3. Install the locking wheel nut key.
2
1
E121887
4
3
2. Slacken the wheel nuts.
3. Jack up the vehicle until the tyre is clear
of the ground.
4. Remove the wheel nuts and the wheel.
Installing a road wheel
5
WARNINGS
Use only approved wheel and tyre
sizes. Using other sizes could
damage the vehicle and will make
the National Type Approval invalid. See
Technical Specifications (page 218).
2
E75442
4. Partially tighten the wheel nuts in the
sequence shown.
5. Lower the vehicle and remove the jack.
6. Fully tighten the wheel nuts in the
sequence shown. See Technical
Specifications (page 218).
7. Install the wheel trim using the ball of
your hand.
Do not fit run flat tyres on vehicles
that were not originally fitted with
them. Please contact your dealer for
more details regarding compatibility.
212
Wheels and Tyres
•
WARNING
Have the wheel nuts checked for
tightness and the tyre pressure
checked as soon as possible.
•
TYRE REPAIR KIT
Your vehicle may not have a spare tyre. In
this case it will have an emergency tyre
repair kit that can be used to repair one
flat tyre.
•
The tyre repair kit is located in the spare
wheel well.
•
General information
•
WARNINGS
Depending on the type and extent of
tyre damage, some tyres can only be
partially sealed or not sealed at all.
Loss of tyre pressure can affect vehicle
handling, leading to loss of vehicle control.
Drive with caution and avoid
making sudden steering or driving
manoeuvres, especially if the vehicle
is heavily loaded or you are towing a
trailer.
The kit will provide you with an
emergency temporary repair, enabling
you to continue your journey to the next
vehicle or tyre dealer, or to drive a
maximum distance of 200 kilometres
(125 miles).
Do not exceed a maximum speed of
80 km/h (50 mph).
Keep the kit out of the reach of
children.
Only use the kit when the ambient
temperature is between –30°C (-22°F)
and +70°C (+158°F).
Using the tyre repair kit
WARNINGS
Compressed air can act as an
explosive or propellant.
Do not use the tyre repair kit if the
tyre has already been damaged as a
result of being driven under inflated.
Never leave the tyre repair kit
unattended while in use.
Do not use the tyre repair kit on run
flat tyres.
CAUTION
Do not try to seal damage other than
that located within the visible tread
of the tyre.
Do not keep the compressor operating
for more than 10 minutes.
Do not try to seal damage to the
tyre’s sidewall.
Note: Use the tyre repair kit only for the
vehicle with which it was supplied.
The tyre repair kit seals most tyre
punctures [with a diameter of up to six
millimetres (1/4 inch)] to temporarily
restore mobility.
•
Observe the following rules when using the
kit:
•
•
213
Park your vehicle at the roadside so
that you do not obstruct the flow of
traffic and so that you are able to use
the kit without being in danger.
Apply the parking brake, even if you
have parked on a level road, to make
sure that the vehicle will not move.
Do not attempt to remove foreign
objects like nails or screws penetrating
the tyre.
Wheels and Tyres
•
•
•
Leave the engine running while the kit
is in use, but not if the vehicle is in an
enclosed or poorly ventilated area (for
example, inside a building). In these
circumstances, switch the compressor
on with the engine turned off.
Replace the sealant bottle with a new
one before the expiry date (see top of
bottle) is reached.
Inform all other users of the vehicle
that the tyre has been temporarily
sealed with the tyre repair kit and make
them aware of the special driving
conditions to be observed.
CAUTION
Screwing the bottle onto the bottle
holder will pierce the seal of the
bottle. Do not unscrew the bottle from
the holder as the sealant will escape.
A
K
B
J
Inflating the tyre
WARNINGS
Check the sidewall of the tyre prior
to inflation. If there are any cracks,
bumps or similar damage, do not
attempt to inflate the tyre.
Do not stand directly beside the tyre
while the compressor is pumping.
I
Watch the sidewall of the tyre. If any
cracks, bumps or similar damage
appear, turn off the compressor and
let the air out by means of the pressure
relief valve B. Do not continue driving with
this tyre.
H
C
D
The sealant contains natural rubber
latex. Avoid contact with skin and
clothing. If this happens, rinse the
affected areas immediately with plenty of
water and contact your doctor.
E94973
If the tyre inflation pressure does not
reach 1.8 bar (26 psi) within seven
minutes, the tyre may have suffered
excessive damage, making a temporary
repair impossible. In this case, do not
continue driving with this tyre.
214
G
F
A
Protective cap
B
Pressure relief valve
C
Hose
D
Orange cap
E
Bottle holder
F
Pressure gauge
E
Wheels and Tyres
G
Power plug with cable
H
Compressor switch
I
Label
J
Bottle lid
K
Sealant bottle
13.
Remove the power plug G from the
cigar lighter socket or auxiliary power
socket.
14. Quickly unscrew the hose C from the
tyre valve and replace the protective
cap A. Fasten the valve cap again.
15. Leave the sealant bottle K in the
bottle holder E.
16. Make sure the kit, the bottle lid and
the orange cap are stored safely, but
still easily accessible in the vehicle.
The kit will be required again when
you check the tyre pressure.
17. Immediately drive approximately
three kilometres (two miles) so that
the sealant can seal the damaged
area.
Note: When pumping in the sealant through
the tyre valve, the pressure may rise up to
6 bar (87 psi) but will drop again after about
30 seconds.
1. Open the lid of the tyre repair kit.
2. Peel off the label I showing the
maximum permissible speed of
80 km/h (50 mph) from the casing and
attach it to the instrument panel in the
driver’s field of view. Make sure the
label does not obscure anything
important.
3. Take the hose C and the power plug
with cable G out of the kit.
4. Unscrew the orange cap D and the
bottle lid J.
5. Screw the sealant bottle K clockwise
into the bottle holder E fully tight.
6. Remove the valve cap from the
damaged tyre.
7. Detach the protective cap A from the
hose C and screw the hose C firmly
onto the valve of the damaged tyre.
8. Make sure that the compressor switch
H is in position 0.
9. Insert the power plug G into the cigar
lighter socket or auxiliary power socket.
See Cigar Lighter (page 111). See
Auxiliary Power Points (page 111).
10. Start the engine.
11.
Move the compressor switch H to
position 1.
12. Inflate the tyre for no longer than
seven minutes to an inflation pressure
of minimum 1.8 bar (26 psi) and a
maximum of 3.5 bar (51 psi). Move
the compressor switch H to position
0 and check the current tyre pressure
with pressure gauge F.
WARNING
If you experience heavy vibrations,
unsteady steering behaviour or
noises while driving, reduce your
speed and drive with caution to a place
where it is safe for you to stop the vehicle.
Recheck the tyre and its pressure. If the
tyre pressure is less than 1.3 bar (19 psi) or
if there are any cracks, bumps or similar
damage visible, do not continue driving
with this tyre.
Checking the tyre pressure
1.
Stop the vehicle after driving
approximately three kilometres
(two miles). Check, and where
necessary, adjust the pressure of the
damaged tyre.
2. Attach the kit and read the tyre
pressure from the pressure gauge F.
215
Wheels and Tyres
3. If the pressure of the sealant-filled tyre
is 1.3 bar (19 psi) or more, adjust it to
the specified pressure. See Technical
Specifications (page 218).
4. Follow the inflation procedure once
again to top up the tyre.
5. Check the tyre pressure again from the
pressure gauge F. If the tyre pressure
is too high, deflate the tyre to the
specified pressure using the pressure
relief valve B.
6. Once you have inflated the tyre to its
correct tyre pressure, move the
compressor switch H to position 0,
remove the power plug G from the
socket, unscrew the hose C, fasten the
valve cap and replace the protective
cap A.
7. Leave the sealant bottle K in the bottle
holder E and store the kit away safely
in its original location.
8. Drive to the nearest tyre specialist to
get the damaged tyre replaced. Before
the tyre is removed from the rim, inform
your tyre dealer that the tyre contains
sealant. Renew the kit as soon as
possible after it has been used once.
Note: Remember that emergency roadside
tyre repair kits only provide temporary
mobility. Regulations concerning tyre repair
after usage of tyre repair kit may differ from
country to country. You should consult a
tyre specialist for advice.
Empty sealant bottles can be disposed of
together with normal household waste.
Return remains of sealant to your dealer
or dispose of it in compliance with local
waste disposal regulations.
TYRE CARE
E70415
To make sure the front and rear tyres of
your vehicle wear evenly and last longer,
we recommend that you swap the tyres
from front to rear and vice versa at regular
intervals of between 5000 and 10000
kilometres (3000 and 6000 miles).
CAUTION
Do not scrub the sidewalls of the tyres
when you are parking.
If you have to mount a kerb, do so slowly
and approach it with the wheels at
right-angles to the kerb.
Examine the tyres regularly for cuts, foreign
objects and uneven wear of the tread.
Uneven wear could mean that the wheel
alignment is outside specification.
WARNING
Before driving, make sure the tyre is
adjusted to the recommended
inflation pressure. See Technical
Specifications (page 218). Monitor the
tyre pressure until the sealed tyre is
replaced.
Check the tyre pressures (including the
spare) when cold, every two weeks.
216
Wheels and Tyres
TYRE PRESSURE
MONITORING SYSTEM
USING WINTER TYRES
CAUTION
WARNINGS
The system does not relieve you of
your responsibility to regularly check
the tyre pressures.
Make sure that you use the correct
wheel nuts for the type of wheel the
winter tyres are fitted to.
If winter tyres are used, make sure that the
tyre pressures are correct. See Technical
Specifications (page 218).
The system will only provide a low
tyre pressure warning. It will not
inflate the tyres.
Do not drive on significantly
under-inflated tyres. This may cause
the tyres to overheat and fail.
Under-inflation reduces fuel efficiency, tyre
tread life and may also affect your ability
to drive the vehicle safely.
USING SNOW CHAINS
WARNINGS
Do not exceed 50 km/h (30 mph).
Do not use snow chains on snow-free
roads.
CAUTIONS
Do not bend or damage the valves
when you are inflating the tyres.
Only fit snow chains to specified
tyres. See Technical
Specifications (page 218).
Have tyres installed by properly
trained technicians.
CAUTION
The Deflation Detection System will alert
you if there is a change of air pressure in
any tyre. It does this by using the ABS
sensors to detect the rolling circumference
of the wheels. When the circumference
changes, this indicates low pressure in a
tyre, a warning message is displayed in the
information display and the message
indicator will illuminate. See Information
Messages (page 83).
If your vehicle is fitted with wheel
trims, remove them before fitting
snow chains.
Note: The ABS will continue to operate
normally.
Only use small link snow chains.
Only use snow chains on the front wheels.
If a low pressure warning message is
displayed in the information display, check
the tyre pressures as soon as possible and
inflate them to the recommended
pressure. See Technical Specifications
(page 218).
Vehicles with stability control
(ESP)
Vehicles with stability control (ESP) may
exhibit some unusual driving
characteristics which can be reduced by
switching traction control off. See Using
Stability Control (page 133).
If this happens frequently, have the cause
determined and rectified as soon as
possible.
217
Wheels and Tyres
System reset
Apart from a too low tyre pressure or a
damaged tyre, the following situations can
affect the rolling circumference:
• Vehicle load is uneven.
• When using a trailer or travelling up and
down an incline.
• Using snow chains.
• Driving on soft surfaces such as snow
or mud.
Note: Do not reset the system when the
vehicle is moving.
Note: You should reset the system
following any adjustment to the tyre
pressures or any changing of tyres.
Note: Turn the ignition on.
1.
Using the information display control,
navigate to Settings > Driver assist
> Deflation detection
2. Press and hold the OK button until
confirmation appears.
Note: The system will still function
correctly, but there may be an increased
detection time.
TECHNICAL SPECIFICATIONS
Wheel nut torque
Wheel type
Nm (Ib-ft)
All
130 (96)
Tyre pressures (cold tyres)
Up to 80 km/h (50 mph)
Normal load
Variant
Tyre size
Full load
Front
Rear
Front
Rear
bar (lbf/
in²)
bar (lbf/
in²)
bar (lbf/
in²)
bar (lbf/
in²)
All
T125/80 R 16
4.2 (61)
4.2 (61)
4.2 (61)
4.2 (61)
All
T125/90 R 16
4.2 (61)
4.2 (61)
4.2 (61)
4.2 (61)
218
Wheels and Tyres
Up to 160 km/h (100 mph)
Normal load
Variant
Tyre size
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
*
2.1 (31)
2.1 (31)
2.4 (35)
2.8 (41)
All
205/55 R 16
1.6L Duratec-16V TiVCT - Sigma, 1.6L
EcoBoost - Sigma,
2.0L Duratec-HE MI4, 1.6L DuratorqTDCi - DV
215/55 R 16
*
2.1 (31)
2.1 (31)
2.4 (35)
2.8 (41)
2.0L Duratorq-TDCi
- DW
215/55 R 16
*
2.3 (33)
2.1 (31)
2.4 (35)
2.8 (41)
1.6L Duratec-16V TiVCT - Sigma, 1.6L
EcoBoost - Sigma,
2.0L Duratec-HE MI4, 1.6L DuratorqTDCi - DV
215/50 R 17
2.1 (31)
2.1 (31)
2.4 (35)
2.8 (41)
2.0L Duratorq-TDCi
- DW
215/50 R 17
2.3 (33)
2.1 (31)
2.4 (35)
2.8 (41)
1.6L Duratec-16V TiVCT - Sigma, 1.6L
EcoBoost - Sigma,
2.0L Duratec-HE MI4, 1.6L DuratorqTDCi - DV
235/40 R 18
2.1 (31)
2.1 (31)
2.4 (35)
2.8 (41)
2.0L Duratorq-TDCi
- DW
235/40 R 18
2.3 (33)
2.1 (31)
2.4 (35)
2.8 (41)
*
Only fit snow chains to specified tyres.
219
Wheels and Tyres
Continuous speed in excess of 160 km/h (100 mph)
Normal load
Variant
Tyre size
Full load
Front
Rear
Front
Rear
bar (psi)
bar (psi)
bar (psi)
bar (psi)
1.6L Duratec-16V TiVCT - Sigma, 1.6L
Duratorq-TDCi - DV
205/55 R 16
2.1 (31)
2.1 (31)
2.4 (35)
2.8 (41)
1.6L EcoBoost Sigma,
205/55 R 16
2.2 (32)
2.1 (31)
2.4 (35)
2.8 (41)
1.6L Duratec-16V TiVCT - Sigma, 1.6L
EcoBoost - Sigma,
2.0L Duratec-HE MI4, 1.6L DuratorqTDCi - DV
215/55 R 16
2.1 (31)
2.1 (31)
2.4 (35)
2.8 (41)
2.0L Duratorq-TDCi
- DW
215/55 R 16
2.3 (33)
2.1 (31)
2.6 (38)
2.8 (41)
1.6L Duratec-16V TiVCT - Sigma, 1.6L
EcoBoost - Sigma,
2.0L Duratec-HE MI4, 1.6L DuratorqTDCi - DV
215/50 R 17
2.1 (31)
2.1 (31)
2.4 (35)
2.8 (41)
2.0L Duratorq-TDCi
- DW
215/50 R 17
2.3 (33)
2.1 (31)
2.6 (38)
2.8 (41)
1.6L Duratec-16V TiVCT - Sigma, 1.6L
EcoBoost - Sigma,
2.0L Duratec-HE MI4, 1.6L DuratorqTDCi - DV
235/40 R 18
2.1 (31)
2.1 (31)
2.4 (35)
2.8 (41)
2.0L Duratorq-TDCi
- DW
235/40 R 18
2.3 (33)
2.1 (31)
2.6 (38)
2.8 (41)
220
Vehicle identification
Note: The vehicle identification plate
design may vary to that shown.
VEHICLE IDENTIFICATION
PLATE
B
C
Note: The information shown on the vehicle
identification plate is dependant upon
market requirements.
D
E
F
G
A
H
I
E135662
A
Model
B
Variant
C
Engine designation
D
Emission level
E
Vehicle identification number
F
Gross vehicle weight
G
Gross train weight
H
Maximum front axle weight
I
Maximum rear axle weight
The vehicle identification number and
maximum weights are shown on a plate
located on the lock side of the right-hand
door aperture at the bottom.
221
Vehicle identification
VEHICLE IDENTIFICATION
NUMBER
E87496
The vehicle identification number is
stamped into the floor panel on the
right-hand side, beside the front seat. It is
also shown on the left-hand side of the
instrument panel.
222
Capacities and Specifications
TECHNICAL SPECIFICATIONS
Vehicle dimensions
4-door
Dimension description
Dimension in mm (inches)
Maximum length
4534 (178.5)
Overall width including exterior mirrors
2010 (79.1)
Overall height - EC kerb weight
1451 - 1484 (57.1 - 58.4)
Wheelbase
2648 (104.3)
Front track
1544 - 1559 (60.8 - 61.4)
Rear track
1534 - 1549 (60.4 - 61)
5-door
Dimension description
Dimension in mm (inches)
Maximum length
4358 - 4412 (171.6 - 173.7)
Overall width including exterior mirrors
2010 (79.1)
Overall height - EC kerb weight
1451 - 1484 (57.1 - 58.4)
Wheelbase
2648 (104.3)
Front track
1544 - 1559 (60.8 - 61.4)
Rear track
1534 - 1549 (60.4 - 61)
Estate
Dimension description
Dimension in mm (inches)
Maximum length
4556 - 4606 (179.4 - 181.3)
Overall width including exterior mirrors
2010 (79.1)
Overall height - EC kerb weight
1472 - 1505 (58 - 59.3)
Wheelbase
2648 (104.3)
Front track
1544 - 1559 (60.8 - 61.4)
223
Capacities and Specifications
Dimension description
Dimension in mm (inches)
Rear track
1534 - 1549 (60.4 - 61)
Towing equipment dimensions
A
B
C
E
D
F
G
E132737
224
Capacities and Specifications
4-door
Item
Dimension description
Dimension in mm (inches)
A
Bumper – centre of tow ball
77 - 80 (3 - 3.1)
B
Attachment point – centre of tow ball
C
Wheel centre – centre of tow ball
D
Centre of tow ball – side member
518 (20.4)
E
Distance between side members
1037 (40.8)
F
Centre of tow ball – centre 1. attachment
point
450 (17.7)
G
Centre of tow ball – centre 2. attachment
point
750 (29.5)
5 (0.2)
1068 - 1071 (42 - 42.2)
5-door
Item
Dimension description
A
Bumper – centre of tow ball
Dimension in mm (inches)
81 - 83 (3.2 - 3.3)
B
Attachment point – centre of tow ball
C
Wheel centre – centre of tow ball
896 - 898 (35.3 - 35.4)
5 (0.2)
D
Centre of tow ball – side member
518 (20.4)
E
Distance between side members
1036 (40.8)
F
Centre of tow ball – centre 1. attachment
point
420 (16.5)
G
Centre of tow ball – centre 2. attachment
point
720 (28.3)
Estate
Item
Dimension description
A
Bumper – centre of tow ball
B
Attachment point – centre of tow ball
C
Wheel centre – centre of tow ball
Dimension in mm (inches)
81 (3.2)
225
76 (3)
1094 (43.1)
Capacities and Specifications
Item
Dimension description
Dimension in mm (inches)
D
Centre of tow ball – side member
590 (23.2)
E
Distance between side members
1179 (46.4)
F
Centre of tow ball – centre 1. attachment
point
474 (18.7)
G
Centre of tow ball – centre 2. attachment
point
719 (28.3)
226
Audio introduction
IMPORTANT AUDIO
INFORMATION
WARNINGS
Due to technical incompatibility,
recordable (CD-R) and rewritable
(CD-RW) discs may not function
correctly.
E66257
Disc labels
Audio CD
These CD radio units will play
compact discs that conform to the
International Red Book standard
audio specification. Copy protected CDs
from some manufacturers do not conform
to this standard and playback cannot be
guaranteed.
Dual format, dual sided discs (DVD
Plus, CD-DVD format), adopted by
the music industry, are thicker than
normal CDs and consequently playback
cannot be guaranteed, and jamming could
occur. Irregular shaped CDs and CDs with
a scratch protection film or self adhesive
labels attached should not be used.
Warranty claims, where this type of disc is
found to be inside an audio unit returned
for repair, will not be accepted.
E66254
MP3
All CD units are designed to play
commercially pressed 12 cm audio
compact discs only.
E66255
The audio unit may be damaged if
unsuitable items like credit cards or
coins are pushed inside the CD
aperture.
Audio unit labels
E66256
227
Audio unit overview
Note: Units have an integrated multi
function display situated above the CD
aperture. This shows important information
regarding control of your audio unit.
Additionally, there are various icons placed
around the display screen which light up
when a function is active (for example CD,
Radio or Aux.)
Type 1
A
B
C
D
E
O
F
N
M
L
G
K
J
I
H
E130324
A
CD eject. See Compact disc player (page 240).
B
Navigation arrows.
C
CD aperture. See Compact disc player (page 240).
D
OK.
E
Information.
F
Traffic announcement. See Traffic information control (page 236).
G
Station presets. See Station preset buttons (page 236).
228
Audio unit overview
H
Seek up. CD track selection. See Station tuning control (page 235). See Track
selection (page 240).
I
On/off and volume control.
J
Seek down. CD track selection. See Station tuning control (page 235). See
Track selection (page 240).
K
Menu select.
L
Sound button. See Sound button (page 235).
M
Auxiliary select. See Auxiliary input (AUX IN) socket (page 113). See
Auxiliary input (AUX IN) socket (page 243).
N
Radio and waveband select. See Audio unit operation (page 235).
O
CD select. See Compact disc player (page 240).
Type 2
1
E104157
A
2
3
4
A
Descriptions for function buttons
1-4
229
Audio unit overview
A
B
C
D
E
F
T
S
G
R
Q
H
P
O
N
M
L
K
J
I
E130142
A
CD eject. See Compact disc player (page 240).
B
Navigation arrows.
C
CD aperture. See Compact disc player (page 240).
D
OK.
E
Information.
F
Traffic announcement. See Traffic information control (page 236).
G
Sound button. See Sound button (page 235).
H
Telephone keypad and station presets. See Using the telephone (page 246).
See Station preset buttons (page 236).
I
Function 4.
J
Function 3.
K
Seek up. CD track selection. See Station tuning control (page 235). See Track
selection (page 240).
230
Audio unit overview
L
On/off and volume control.
M
Seek down. CD track selection. See Station tuning control (page 235). See
Track selection (page 240).
N
Function 2.
O
Function 1.
P
Menu select.
Q
Phone menu. See Telephone (page 245).
R
Auxiliary, USB and iPod select. See Auxiliary input (AUX IN) socket (page
113). See Auxiliary input (AUX IN) socket (page 243). See Connectivity
(page 265).
S
Radio and waveband select. See Audio unit operation (page 235).
T
CD select. See Compact disc player (page 240).
Type 3
Function buttons 1 to 4 are context
dependent, and change according to the
current unit mode. Descriptions for the
functions are shown at the bottom of the
screen display.
1
E104157
A
231
2
3
4
A
Descriptions for function buttons
1-4
Audio unit overview
A
B
C
D
E
F
G
Y
X
H
W
I
V
J
U
K
T
L
S
R
Q
P
O
N
M
E129074
A
On/off control.
B
Display select.
C
Telephone keypad and station presets. See Using the telephone (page 246).
See Station preset buttons (page 236).
D
CD aperture. See Compact disc player (page 240).
E
Navigation arrows.
F
DSP select. See Digital signal processing (DSP) (page 238).
G
CD eject. See Compact disc player (page 240).
H
Information.
I
Clock.
J
Seek up. CD track selection. End call. See Station tuning control (page 235).
See Track selection (page 240). See Using the telephone (page 246).
K
Mute.
232
Audio unit overview
L
Traffic announcement. See Traffic information control (page 236).
M
Function 4.
N
Sound button. See Sound button (page 235).
O
Function 3.
P
OK.
Q
Function 2.
R
Menu select.
S
Function 1.
T
Phone menu. See Telephone (page 245).
U
Auxiliary select. See Auxiliary input (AUX IN) socket (page 113). See
Auxiliary input (AUX IN) socket (page 243).
V
Seek down. CD track selection. Accept call. See Station tuning control (page
235). See Track selection (page 240). See Using the telephone (page 246).
W
Radio and waveband select. See Audio unit operation (page 235).
X
CD select. See Compact disc player (page 240).
Y
Volume control.
Function buttons 1 to 4 are context
dependent, and change according to the
current unit mode. Descriptions for the
functions are shown at the bottom of the
screen display.
233
Audio system security
SECURITY CODE
Each unit incorporates a unique code that
is linked to the vehicle identification
number (VIN). The system will
automatically check that the audio unit
and vehicle match before allowing
operation.
If a security code message appears, please
see your dealer.
234
Audio unit operation
Note: The system will automatically
change to another corresponding station if
the current one becomes unavailable, for
example when leaving the coverage area.
ON/OFF CONTROL
Press the on/off control. This will also
operate the unit for up to one hour with the
ignition turned off.
Switching DAB service linking on and off.
See General Information (page 75).
The radio will switch off automatically
after one hour.
Seek tuning
Select a waveband and briefly press one
of the seek buttons. The unit will stop at
the first station it finds in the direction you
have chosen.
SOUND BUTTON
This will allow you to adjust the sound
settings (for example bass and treble).
Manual tuning
1. Press the sound button.
2. Use the up and down arrow buttons to
select the required setting.
3. Use the left and right arrow buttons to
make the necessary adjustment. The
display indicates the level selected.
4. Press the OK button to confirm the
new settings.
Type 1
1. Press the MENU button.
2. Select RADIO mode and then MANUAL
TUNE.
3. Use the left and right arrow buttons to
tune down or up the waveband in small
increments or press and hold to
increment quickly, until you find a
station you want to listen to.
4. Press OK to continue listening to a
station.
WAVEBAND BUTTON
Press the RADIO button to select from the
wavebands available.
The selector can also be used to return to
radio reception when you have been
listening to another source.
Type 2 and 3
1. Press function button 2.
2. Use the left and right arrow buttons to
tune down or up the waveband in small
increments or press and hold to
increment quickly, until you find a
station you want to listen to.
3. Press OK to continue listening to a
station.
Alternatively, press the left arrow button
to display the available wavebands. Scroll
to the required waveband and press OK.
STATION TUNING CONTROL
DAB service linking
Scan tuning
Note: The DAB service linking is as per
default off.
Scan allows you to listen to a few seconds
of each station detected.
Note: Service linking allows
cross-referencing to other corresponding
frequencies of the same station, for example
FM and other DAB ensembles.
Type 1
1.
235
Press the MENU button.
Audio unit operation
2. Select RADIO mode and then SCAN.
3. Use the seek buttons to scan up or
down the selected waveband.
4. Press OK to continue listening to a
station.
AUTOSTORE CONTROL
Note: This will store up to a maximum of
the 10 strongest signals available, either
from the AM or the FM waveband, and
overwrite the previously stored stations. It
can also be used to store stations manually
in the same way as other wavebands.
Type 2 and 3
1. Press function button 3.
2. Use the seek buttons to scan up or
down the selected waveband.
3. Press function button 3 again or OK to
continue listening to a station.
Note: On type 3 you must select either FM
AST or AM AST to use this function.
•
•
STATION PRESET BUTTONS
This feature allows you to store your
favourite stations so that they can be
recalled by selecting the appropriate
waveband and pressing one of the preset
buttons.
Press and hold function button 1 or the
RADIO button.
When the search is complete, sound is
restored and the strongest signals are
stored on the Autostore presets.
TRAFFIC INFORMATION
CONTROL
Many stations that broadcast on the FM
waveband have a TP code to signify that
they carry traffic programme information.
1. Select a waveband.
2. Tune to the station required.
3. Press and hold one of the preset
buttons. A progress bar and message
will appear. When the progress bar
completes the station has been stored.
The audio unit will also mute
momentarily as confirmation.
Activating traffic announcements
Before you can receive traffic
announcements, you must press either the
TA or TRAFFIC button. A ‘TA’ display will
appear to show the feature is switched on.
If you are already tuned to a station that
broadcasts traffic information, ‘TP’ will
also be displayed. Otherwise the unit will
search for a traffic programme.
This can be repeated on each waveband
and for each preset button.
Note: When you drive to another part of the
country, FM and DAB stations that
broadcast on alternative frequencies, and
are stored on preset buttons, may be
updated with the correct frequency and
station name for that area.
When traffic information is broadcast, it
will automatically interrupt normal radio
or CD playback and ‘Traffic announcement
(TA)’ will appear in the display.
If a non-traffic station is selected or
recalled using a preset button, the audio
unit will remain on that station unless TA
or TRAFFIC is turned off, then on again.
Note: If TA is on and you select a preset or
manual tune to a non TA station no traffic
announcement will be heard.
236
Audio unit operation
Note: When you are listening to a non TA
station and turn TA off and on again a TP
seek will occur.
Traffic announcement volume
Traffic announcements interrupt normal
broadcasts at a preset minimum level that
is usually louder than normal listening
volumes.
To adjust the preset volume:
•
Use the volume control to make the
necessary adjustment during an
incoming TA broadcast. The display
will show the level selected.
Ending traffic announcements
The audio unit will return to normal
operation at the end of each traffic
announcement. To end the announcement
prematurely, press TA or TRAFFIC during
the announcement.
Note: If you press TA or TRAFFIC at any
other time it will switch all announcements
off.
237
Audio unit menus
AUTOMATIC VOLUME
CONTROL
NEWS BROADCASTS
Some audio units interrupt normal
reception to broadcast news bulletins from
stations on the FM waveband or radio data
system (RDS) and enhanced other
network (EON) linked stations, in the same
way as traffic information is provided.
When available, automatic volume control
(AVC) adjusts the volume level to
compensate for engine noise and road
speed noise.
1.
2.
3.
4.
5.
Press the MENU button and select
AUDIO.
Select AVC LEVEL or ADAPTIVE VOL.
Use the left or right arrow button to
adjust the setting.
Press the OK button to confirm your
selection.
Press the MENU button to return.
During news broadcasts, the display will
indicate there is an incoming
announcement. News interrupts are
broadcast at the same preset volume level
as traffic announcements.
1. Press the MENU button.
2. Select AUDIO or AUDIO SETTINGS.
3. Scroll to NEWS and turn on or off with
the OK button.
4. Press the MENU button to return.
DIGITAL SIGNAL PROCESSING
(DSP)
ALTERNATIVE FREQUENCIES
DSP occupancy
Many programmes that broadcast on the
FM waveband have a programme
identification (PI) code, which can be
recognised by audio units.
This feature takes into account the
differences in distance from the various
speakers in the vehicle to each seat. Select
the sitting position for which the audio is
to be correctly enhanced.
If your radio has alternative frequencies
(AF) tuning switched on and you move
from one transmission area to another, this
facility will search for and switch to a
stronger station signal, if one can be found.
DSP equaliser
Select the music category that most suits
your listening preference. The audio output
will change to enhance the particular style
of music chosen.
Under certain conditions, however, AF
tuning may temporarily disrupt normal
reception.
Changing the DSP settings
When selected, the unit continually
evaluates signal strength and, if a better
signal becomes available, the unit will
switch to that alternative. It mutes while
it checks a list of alternative frequencies
and, if necessary, it will search once across
the selected waveband for a genuine
alternative frequency.
1.
2.
3.
4.
Press the MENU button.
Select AUDIO or AUDIO SETTINGS.
Scroll to the required DSP function.
Use the up and down arrow buttons to
select the required setting.
5. Press the OK button to confirm your
selection.
6. Press the MENU button to return.
238
Audio unit menus
It will restore radio reception when it finds
one or, if one is not found, the unit will
return to the original stored frequency.
When selected, ‘AF’ will be shown in the
display.
1. Press the MENU button.
2. Select AUDIO or AUDIO MENU.
3. Scroll to ALTERNAT FREQ. or
ALTERNATIVE FREQ. and turn on or off
with the OK button.
4. Press the MENU button to return.
REGIONAL MODE (REG)
Regional mode (REG) controls the
behaviour of AF switching between
regionally related networks of a parent
broadcaster. A broadcaster may run a fairly
large network across a large part of the
country. At various times of the day this
large network may be broken down into a
number of smaller regional networks,
typically centred on major towns or cities.
When the network is not split into regional
variants, the whole network caries the
same programming.
Regional mode ON: This prevents 'random'
AF switches when neighbouring regional
networks are not carrying the same
programming.
Regional mode OFF: This allows a larger
coverage area if neighbouring regional
networks are carrying the same
programming, but can cause 'random' AF
switches if they are not.
1. Press the MENU button.
2. Select AUDIO or AUDIO SETTINGS.
3. Scroll to RDS REGIONAL and turn on
or off with the OK button.
4. Press the MENU button to return.
239
Compact disc player
COMPACT DISC PLAYBACK
SHUFFLE/RANDOM
Note: During playback, the display indicates
the disc, track and time that has elapsed
since the start of the track.
Random track playback, also known as
shuffle, plays all tracks on the CD in
random order.
During radio reception, press the CD button
once to start CD playback.
Type 1
Playback will start immediately after a disc
is loaded.
1.
Press the MENU button and select CD
MODE.
2. Select SHUFFLE, which then enables
the function to be selected on or off.
TRACK SELECTION
•
•
•
•
When an MP3 CD is playing, options
include SHUFFLE for the whole CD, or to
play all the tracks in the folder in a random
order.
Press the seek up button once to move
to the next track or press it repeatedly
to access later tracks.
Press the seek down button once to
replay the current track. If pressed
within two seconds of the start of a
track, the previous track will be
selected.
Press the seek down button repeatedly
to select previous tracks.
Type 2 and 3
Press function button 2.
Note: When an MP3 CD is playing, options
include SHUFFLE for the whole CD, or to
play all the tracks in the folder in a random
order. Repeat presses of function button 2
will toggle these options.
Press the up or down arrow buttons,
and using the OK button, select the
required track.
Use the seek up or down button to select
the next track to shuffle if required.
Type 2 and 3
REPEAT COMPACT DISC
TRACKS
The desired track number may be entered
using the numeric keypad. Dial the required
track number until complete (for example
1 then 2 for track 12), or dial the number
and directly press OK.
Type 1
1.
Press the MENU button and select CD
MODE.
2. Select REPEAT, which then enables
the function to be selected on or off.
The track will replay once ended.
FAST FORWARD/REVERSE
Press and hold the seek down or up
buttons to search backwards or forwards
within the tracks on the disc.
When an MP3 CD is playing, options
include REPEAT for the track, or to repeat
all the tracks in the folder.
Type 2 and 3
Press function button 1.
240
Compact disc player
When an MP3 CD is playing, options
include REPEAT for the track, or to repeat
all the tracks in the folder. Repeat presses
of function button 1 will toggle these
options.
When a CD containing audio is inserted
into the CD player the disc's directory
structure is read in. It may take a while
before playback starts and is dependant
on the quality of the disc.
MP3 tracks may be recorded on the CD in
several ways. They can all be placed in the
root directory like a conventional audio CD,
or they can be placed in folders that may
represent, for example, an album, an artist,
or a genre.
COMPACT DISC TRACK
SCANNING
The SCAN function allows you to preview
each track for approximately 5 seconds.
Playing a multi session disc
Type 1
The normal playing sequence on CD's with
multiple folders is to play the tracks in the
first folder, then the tracks in any folders
nested inside the first folder, then move
onto the second folder, and so on. For
example, if folder 1 has folders 1a and 1b
within it, and folder 2 contains folder 2a,
the playing sequence will be folder 1, 1a, 1b,
2, 2a.
Various scan modes are possible,
according to the type of CD currently
playing.
1.
Press the MENU button and select CD
MODE.
2. Select SCAN, which then enables the
function to be selected on or off.
Note: When an MP3 CD is playing, options
include SCAN for the CD, or just the tracks
in the folder.
When the playback of a file is finished the
playback of the other files in the same
directory continues. Directory change takes
place automatically when all files in the
current directory have been played back.
3. Press the OK button to stop the scan
mode.
Type 2 and 3
MP3 DISPLAY OPTIONS
1. Press function button 3.
Note: When an MP3 CD is playing, options
include SCAN for the CD, or just the tracks
in the folder. Repeat presses of function
button 3 will toggle these options.
When an MP3 disc is playing, certain
information encoded in each track can be
displayed. Such information will normally
include:
•
•
•
2. Press function button 3 again to stop
the scan mode.
MP3 FILE PLAYBACK
The file name
The folder name
ID3 information which might be the
album or artist’s name.
The unit will normally show the file name
that is playing. To select one of the other
items of information, press the INFO
button repeatedly until the required item
is shown in the display.
Note: Some copy protected audio files may
not be read by the CD player.
The CD player also supports MP3 and
WMA format audio files.
241
Compact disc player
Note: If the ID3 information selected is
unavailable, NO MP3 TAG will be shown in
the display.
CD text display options
When an audio disc with CD text is playing,
limited information encoded in each track
can be displayed. Such information will
normally include:
•
•
•
The disc name
The artist name
The track name.
Note: These display options are selected
in the same way as MP3 displays. NO DISC
NAME or NO TRACK NAME will be shown
in the display if no information has been
encoded.
ENDING COMPACT DISC
PLAYBACK
To restore radio reception on all units:
•
Press the RADIO button.
Note: This will not eject the CD; the disc
will merely pause at the point where radio
reception was restored.
To resume CD playback, press the CD
button again.
242
Auxiliary input (AUX IN) socket
Note: For optimum performance when
using any auxiliary device set the volume on
the device high. This will reduce audio
interference when charging the device via
the vehicle power supply socket.
When fitted the Auxiliary input (AUX IN)
socket permits an auxiliary device, such as
an MP3 player, to be linked into the vehicle
audio system. Output can be played
through the vehicle speakers.
To connect an auxiliary device, plug it into
the AUX IN socket using a 3.5 mm
conventional audio jack connector.
Select the auxiliary input via the AUX
button and playback will be heard through
the vehicle speakers. LINE IN or LINE IN
ACTIVE will appear in the vehicle audio
unit display. Volume, treble and bass can
be adjusted on the vehicle audio unit as
normal.
The vehicle audio unit buttons can also be
used to restore playback from the vehicle
audio unit, while the auxiliary device
remains connected.
243
Audio troubleshooting
Audio unit display
Rectification
PLEASE CHECK CD
General error message for CD fault conditions, such as
cannot read the CD, data-CD inserted, etc. Ensure disc
is loaded correct way up. Clean and re-try, or replace
disc with known music disc. If error persists contact your
dealer.
CD DRIVE MALFUNCTION
General error message for CD fault conditions such as
possible mechanism fault.
CD DRIVE HIGH TEMP
Ambient temperature too hot – unit will not work until
it has cooled down.
IPOD ERROR READING DEVICE
General error message for iPod fault conditions, such
as cannot read the data. Ensure iPod is inserted
correctly. If error persists contact your dealer.
244
Telephone
Note: If there is an ongoing call when the
phone in use is selected as the new active
phone, the call is transferred to the vehicle
audio system.
GENERAL INFORMATION
CAUTION
Using the system with the engine off
will drain the battery.
Note: Even if connected to the car system,
your phone can still be used in the usual
way.
This section describes the functions and
features of the Bluetooth mobile phone
hands free system.
Requirements for Bluetooth
connection
The Bluetooth mobile phone part of the
system provides interaction with the audio
or navigation system and your mobile
phone. It allows you to use the audio or
navigation system to make and receive
calls without having to hold your mobile
phone.
The following are required before a
Bluetooth phone connection can be made.
1.
The Bluetooth feature must be
activated on the phone and on the
audio unit. Make sure the Bluetooth
menu option in the audio unit is set to
ON. For information on phone settings,
refer to your phone user guide.
2. In the Bluetooth menu on your phone,
search for Ford Audio and select it.
3. Enter the code number shown on the
vehicle display using the phone keypad.
If no code number is shown on the
display, enter the Bluetooth PIN
number 0000 using the phone keypad.
Now enter the Bluetooth PIN number
shown on the vehicle display.
4. If your mobile phone asks you to
authorize the automatic connection,
select YES.
Compatibility of phones
CAUTION
As no common agreement exists,
mobile phone manufacturers are able
to implement a variety of profiles in
their Bluetooth devices. Because of this,
an incompatibility can occur between the
phone and hands-free system, which in
some cases may significantly degrade the
system performance. To avoid this
situation, only recommended phones
should be used.
Please visit the website www.fordmobile-connectivity.com for full details.
Note: A phone call will be disconnected if
the audio unit is switched off. If the ignition
key is turned to the off position the phone
call will remain in progress.
BLUETOOTH SETUP
Before you can use your telephone with
your vehicle it must be bonded to the
vehicle telephone system.
TELEPHONE SETUP
Handling of phones
Note: It may be necessary to confirm
phonebook access to the Bluetooth system
via the mobile phone.
Phonebook
Up to six Bluetooth devices can be bonded
to the vehicle system.
245
Telephone
Bond another Bluetooth phone
After start up access to the phonebook list
can be delayed for several minutes,
depending upon the size.
Bond a new Bluetooth phone as described
in the requirements for a Bluetooth
connection.
Phonebook categories
Phones stored in the system are accessible
by using the phone list on the audio unit.
The category is indicated as an icon:
Phone
Mobile
Note: A maximum of six devices may be
bonded. If six Bluetooth devices have
already been bonded, one of these has to
be debonded in order to bond a new device.
Home
TELEPHONE CONTROLS
E87990
E87991
Remote control
E87992
Office
E87993
A
Making a phone an active phone
E
Note: If there is an ongoing call when the
phone in use is selected as the new active
phone, the call is transferred to the vehicle
audio system.
D
B
When using the system for the first time,
no phone is connected to the system.
After switching on the ignition and the
audio unit, the Bluetooth phone must be
bonded to the system. See Bluetooth
setup (page 245).
C
E129649
After bonding a Bluetooth phone to the
system, this becomes the active phone.
For further information refer to the phone
menu.
A
Volume up
B
Voice button
C
End call
Select the phone from the active phone
menu.
D
Volume down
E
Receive call
Turning the ignition and radio back on
again, the last active phone is picked up by
the system.
USING THE TELEPHONE
Note: In some cases the Bluetooth
connection must also be confirmed on the
phone.
Note: Refer to your audio guide for details
of the controls. See Audio unit overview
(page 228).
246
Telephone
Note: You can exit the phone menu by
pressing any source button CD, RADIO or
AUX.
Dialling a number using the telephone
keypad
1. Press the PHONE button.
2. Dial the number using the telephone
keypad on the audio unit.
3. Press the OK button.
Note: If you enter an incorrect digit whilst
entering a phone number, press function
button 3 to erase the last digit. A long press
will erase the complete string of digits.
Note: When referred to, the use of the
up/down arrow buttons, seek up and seek
down buttons, and the OK button can be
used on either the steering wheel or the
audio unit.
This chapter describes the phone functions
of the audio unit.
An active phone must be present.
Ending a call
Even if connected to the audio unit, your
phone can still be used in the usual way.
Calls can be ended by:
• pressing the seek up button
• pressing the OK button
• pressing function button 4.
Making a call
Dialling a number using voice control
Phone numbers can be dialled using voice
control. See Telephone commands
(page 257).
Redialling a number
1. Press the PHONE button.
2. Press the up/down arrow buttons until
CALL LISTS is displayed.
3. Press the OK button.
Note: If the active phone does not provide
a call out list, the last outgoing call
number/entry can be redialled.
Dialling a number using the address
book
1. Press the PHONE button.
2. Press the up/down arrow buttons until
PHONEBOOK is shown.
3. Press the OK button.
Note: You can also use the telephone
keypad to select the first letter of the entry
you are looking for. Press the relevant
number that corresponds to the letter
repeatedly until the required letter is
displayed.
4. Press the up/down buttons to select
the desired call list.
5. Press the OK button.
6. Press the up/down buttons to select
the desired phone number.
7. Press the OK button.
4. Press the up/down arrow buttons to
select the desired phone number.
Note: Press and hold the up/down arrow
buttons to search forwards or backwards
within the phonebook.
Redialling the last dialled number
1. Press the PHONE button.
2. Press the up/down arrow buttons until
REDIAL is displayed.
3. Press the OK button.
5. Press the OK button to dial the
selected phone number.
247
Telephone
Receiving an incoming call
Muting the microphone
Accepting an incoming call
Note: During a call, it is possible to mute
the microphone. Whilst muted, confirmation
will appear in the display.
Incoming calls can be accepted by pressing
the seek down button, or by pressing the
OK button.
Press function button 1. Press the button
once again to turn this function off.
Rejecting an incoming call
Changing the active phone
Incoming calls can be rejected by:
• pressing the seek up button, or
• pressing the arrow down button to
highlight REJECT and then pressing
the OK button.
Note: Phones must be bonded to the
system before they can be made active.
Note: After bonding a phone to the system,
this becomes the active phone.
1. Press the PHONE button.
2. Press the up/down buttons until
SELECT PHONE is shown.
3. Press the OK button.
4. Scroll through the different stored
phones by using the up/down buttons
to display the bonded phones.
5. Press the OK button to select the
phone which is to be the active phone.
Receiving a second incoming call
Note: The second incoming call function
must be activated in your phone.
If there is an incoming call whilst there is
an ongoing call, a beep will be heard and
you will have the option to end the active
call and to accept the incoming call.
Accepting a second incoming call
Debonding a bonded phone
Note: The first incoming call will be
disconnected and replaced by the second
incoming call.
A bonded phone can be deleted from the
system at any time, unless a phone call is
in progress.
Second incoming calls can be accepted
by pressing the seek down button on the
steering wheel or on the audio unit, or by
pressing the OK button on the audio unit.
1. Press the PHONE button.
2. Press the up/down buttons until
SELECT PHONE is shown.
3. Press the OK button.
4. Press the up/down buttons to highlight
the required phone.
5. Press function button 1.
Rejecting a second incoming call
Second incoming calls can be rejected by:
• pressing the seek up button, or
• pressing the arrow down button to
highlight REJECT and then pressing
the OK button.
Second incoming calls can be rejected by
pressing function button 4.
248
Voice control
If you are not sure how to continue say
"HELP" for assistance or "CANCEL" if you
do not wish to continue.
PRINCIPLE OF OPERATION
CAUTION
The "HELP" function provides only a
subset of the available voice commands.
Detailed explanations of all possible voice
commands can be found on the following
pages.
Using the system with the engine off
will drain the battery.
Voice recognition enables operation of the
system without the need to divert your
attention from the road ahead in order to
change settings, or receive feedback from
the system.
Voice commands
All voice commands should be given using
a natural speaking voice, as if speaking to
a passenger or on the phone. Your voice
level should be dependant on the
surrounding noise level inside or outside
the vehicle but do not shout.
Whenever you issue one of the defined
commands with the system active, the
voice recognition system converts your
command into a control signal for the
system. Your inputs take the form of
dialogues or commands. You are guided
through these dialogues by
announcements or questions.
USING VOICE CONTROL
System operation
Please familiarise yourself with the
functions of the system before using voice
recognition.
The order and content of the voice controls
are given in the following lists. The tables
show the sequence of user voice
commands and system responses for each
available function.
Supported commands
The voice control system allows you to
control the following vehicle functions:
•
Bluetooth phone
<> indicates a number or stored name tag
to be inserted by the user.
•
radio
Short cuts
•
CD Player
•
external device (USB)
•
external device (iPod)
•
automatic climate control
There are a number of voice command
short cuts available, which allow you to
control some vehicle features without
having to follow the complete command
menu. These are:
•
System response
•
As you work through a voice session the
system will prompt you with a beep tone
each time the system is ready to proceed.
Do not try to give any commands until the
beep tone has been heard. The voice
control system will repeat each spoken
command back to you.
•
•
•
249
phone: "MOBILE NAME", "DIAL
NUMBER", "DIAL NAME", and "REDIAL"
automatic climate control:
"TEMPERATURE", "AUTO MODE",
"DEFROSTING/DEMISTING ON" and
"DEFROSTING/DEMISTING OFF"
radio: "TUNE NAME"
external device (USB): "TRACK"
external device (iPod): "TRACK"
Voice control
Start communicating with the system
•
Store up to 20 name tags per function.
Before you can start talking to the system
you first have to press the VOICE button
for each operation and wait until the
system answers with a beep. See Voice
Control (page 42).
•
The average recording time for each
name tag is approximately 2-3
seconds.
AUDIO UNIT COMMANDS
Press the button again to cancel the voice
session.
CD Player
You can control playback directly by voice
control.
Name tag
The name tag functionality can support
the phone, audio and navigation features
by using the "STORE NAME" function. You
can assign name tags to items such as
favourite radio stations and personal
phone contacts. See Audio unit
commands (page 250). See Telephone
commands (page 257).
Overview
The overview below shows the available
voice commands. The following lists will
give further information about the
complete command menu in selected
examples.
"CD PLAYER"
"HELP"
"PLAY"
"TRACK"
*
"SHUFFLE ALL"
"SHUFFLE FOLDER"
**
"SHUFFLE OFF"
"REPEAT FOLDER"
**
"REPEAT TRACK"
"REPEAT OFF"
* Can be used as a shortcut.
** Only available if the CD contains audio data files like MP3.
Track
You can choose a track on your CD directly.
250
Voice control
Steps
User says
System answer
1
"CD PLAYER"
"CD PLAYER"
2
"TRACK"
3
"<a number between 1 and 99>"
"TRACK NUMBER PLEASE"
*
"TRACK <number>"
**
* Can be used as a shortcut.
** Additionally, numbers can be spoken as up to four single digits (for example "2", "4",
"5" for track 245)
Shuffle all
To set random playback.
Steps
User says
System answer
1
"CD PLAYER"
"CD PLAYER"
2
"SHUFFLE ALL"
Overview
Radio
The overview below shows the available
voice commands. The following lists will
give further information about the
complete command menu.
The radio voice commands support the
functionality of the radio and allow you to
tune radio stations by voice control.
"RADIO"
"HELP"
"AM"
"FM"
"TUNE NAME"
*
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
251
Voice control
"RADIO"
"PLAY"
* Can be used as a shortcut.
Tune frequency
This function allows you to tune your radio
by voice commands.
Steps
User says
System answer
1
"RADIO"
"RADIO"
2
"AM"
"AM FREQUENCY PLEASE"
"FM"
"FM FREQUENCY PLEASE"
3
"<frequency>"
"TUNE <frequency>"
*
* The frequency may be entered in a variety of ways. Refer below for representative
examples.
•
•
•
•
•
FM band: 87.5 - 108.0 in increments of 0.1
•
•
•
•
•
"Eighty nine point nine" (89.9)
"Ninety" (90.0)
"One hundred point five" (100.5)
"One zero one point one" (101.1)
"One zero eight" (108.0)
"Five thirty one" (531)
"Nine hundred" (900)
"Fourteen forty" (1440)
"Fifteen zero three" (1503)
"Ten eighty" (1080)
Store name
AM/MW band: 531 - 1602 in increments of
9
If you have tuned a radio station, you can
store it with a name in the directory.
AM/LW band: 153 - 281 in increments of 1
Steps
User says
System answer
1
"RADIO"
"RADIO"
2
"STORE NAME"
"STORE NAME"
"NAME PLEASE"
3
"<name>"
"REPEAT NAME PLEASE"
4
"<name>"
"STORING NAME"
"<name> STORED"
252
Voice control
Tune name
This function allows you to call up a stored
radio station.
Steps
User says
1
"RADIO"
2
"TUNE NAME"
3
"<name>"
System answer
"RADIO"
"NAME PLEASE"
*
"TUNE <name>"
* Can be used as a shortcut.
Delete name
This function allows you to delete a stored
radio station.
Steps
User says
System answer
1
"RADIO"
"RADIO"
2
"DELETE NAME"
"NAME PLEASE"
3
"<name>"
"DELETE <name>"
"CONFIRM YES OR NO"
4
"YES"
"DELETED"
"NO"
"COMMAND CANCELLED"
Play directory
This function allows you to let the system
tell you all of the stored radio stations.
Steps
User says
System answer
1
"RADIO"
"RADIO"
2
"PLAY DIRECTORY"
"PLAY <DIRECTORY>"
Delete directory
This function allows you to delete all
stored radio stations at once.
253
Voice control
Steps
User says
System answer
1
"RADIO"
"RADIO"
2
"DELETE DIRECTORY"
"DELETE DIRECTORY"
"CONFIRM YES OR NO"
3
"YES"
"RADIO DIRECTORY DELETED"
"NO"
"COMMAND CANCELLED"
Play
This function switches the audio source to
the radio mode.
Steps
User says
System answer
1
"RADIO"
"RADIO"
2
"PLAY"
Auxiliary input
This function allows you to switch the
audio source to the attached auxiliary input
device.
Steps
User says
System answer
1
"EXTERNAL DEVICE"
"EXTERNAL DEVICE"
2
"LINE IN"
"LINE IN"
Overview
External devices - USB
The overview below shows the available
voice commands. The following lists will
give further information about the
complete command menu in selected
examples.
These voice commands support the
functionality of an external USB device
which may be connected to the audio unit.
"EXTERNAL DEVICE", "USB"
"HELP"
254
Voice control
"EXTERNAL DEVICE", "USB"
"PLAY"
"TRACK"
*
"PLAYLIST"
"FOLDER"
**
**
"SHUFFLE ALL"
"SHUFFLE FOLDER"
"SHUFFLE PLAYLIST"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT FOLDER"
"REPEAT OFF"
* Can be used as a shortcut.
** Playlists and folders activated by voice control must be assigned special filenames.
See General Information (page 265).
USB play
This function allows you to switch the
audio source to the attached USB device.
Steps
User says
System answer
1
"EXTERNAL DEVICE"
"EXTERNAL DEVICE"
2
"USB"
"USB"
3
"PLAY"
USB Track
You can choose a track on your USB device
directly.
255
Voice control
Steps
User says
System answer
1
"EXTERNAL DEVICE"
"EXTERNAL DEVICE"
2
"USB"
"USB"
3
"TRACK"
4
"TRACK NUMBER PLEASE"
"<a number between 1 and 99>"
*
"TRACK <number>"
* Additionally, numbers can be spoken as up to four single digits (for example "2", "4",
"5" for track 245)
Overview
External devices - iPod
The overview below shows the available
voice commands. The following lists will
give further information about the
complete command menu in selected
examples.
These voice commands support the
functionality of an iPod which may be
connected to the audio unit.
"EXTERNAL DEVICE", "IPOD"
"HELP"
"PLAY"
"TRACK"
*
"PLAYLIST"
**
"SHUFFLE ALL"
"SHUFFLE PLAYLIST"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT OFF"
* Can be used as a shortcut.
** Playlists activated by voice control must be assigned special filenames. See General
Information (page 265).
256
Voice control
iPod Track
You can choose a track off the all titles list
of your iPod directly.
Steps
User says
System answer
1
"EXTERNAL DEVICE"
"EXTERNAL DEVICE"
2
"IPOD"
"IPOD"
3
"TRACK NUMBER PLEASE"
"TRACK"
4
"<a number between 1 and 99>"
*
"TRACK <number>"
**
* Can be used as a shortcut.
** Additionally, numbers can be spoken as up to five single digits (for example "5", "2",
"4", "5", "3" for track 52453), to a limit of 65535.
iPod playlist
You can choose a playlist from your iPod
directly.
Steps
User says
System answer
1
"EXTERNAL DEVICE"
"EXTERNAL DEVICE"
2
"IPOD"
"IPOD"
3
"PLAYLIST"
"PLAYLIST NUMBER PLEASE"
4
"<a number between 1 and 10>"
*
"PLAYLIST <number>"
* Playlists activated by voice control must be assigned special filenames. See General
Information (page 265).
Overview
TELEPHONE COMMANDS
The overview below shows the available
voice commands. The following lists will
give further information about the
complete command menu in selected
examples.
Phone
Your phone system allows you to create
an additional phonebook. The stored
entries can be dialled by voice control.
Phone numbers stored by using voice
control are stored on the vehicle system
and not in your phone.
257
Voice control
"PHONE"
"HELP"
"MOBILE NAME"
"DIAL NUMBER"
"DIAL NAME"
*
*
*
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
"REDIAL"
*
"ACCEPT CALLS"
"REJECT CALLS"
* Can be used as a shortcut.
Phone functions
Dial number
Phone numbers can be dialled after giving
the name tag voice command.
Steps
User says
System answer
1
"PHONE"
"PHONE"
2
"DIAL NUMBER"
3
"<phone number>"
"<phone number>
CONTINUE?"
4
"DIAL"
"DIALLING"
"CORRECTION"
"<repeat last part of number>
CONTINUE?"
"NUMBER PLEASE"
*
* Can be used as a shortcut.
258
Voice control
Dial name
Phone numbers can be dialled after giving
the name tag voice command.
Steps
User says
1
"PHONE"
System answer
"PHONE"
2
"DIAL NAME"
"NAME PLEASE"
3
"<name>"
"DIAL <name>"
"CONFIRM YES OR NO"
4
"YES"
"DIALLING"
"NO"
"COMMAND CANCELLED"
*
* Can be used as a shortcut.
Redial
This function allows you to redial the last
dialled phone number.
Steps
User says
System answer
"PHONE"
1
"PHONE"
2
"REDIAL"
*
3
"YES"
"DIALLING"
"NO"
"COMMAND CANCELLED"
"REDIAL"
"CONFIRM YES OR NO"
* Can be used as a shortcut.
Mobile name
This function allows you to access phone
numbers stored with a name tag in your
mobile phone.
Steps
User says
System answer
1
"PHONE"
"PHONE"
2
"MOBILE NAME"
"MOBILE NAME" "<phone
dependent dialogue>"
*
* Can be used as a shortcut.
259
Voice control
DTMF (Tone dialling)
Note: DTMF can only be used during an
ongoing call. Operate the VOICE button and
wait for the system prompt.
This function transfers spoken numbers
into DTMF tones. For example, to make a
remote enquiry to your home answering
machine or to enter a PIN number etc.
Steps
Can only be used with vehicles installed with
a dedicated VOICE button.
User says
System answer
1
2
"NUMBER PLEASE"
"<numbers 1 to 9, zero, hash, star>"
Create a phonebook
Store name
New entries can be stored with the
"STORE NAME" command. This feature
can be used to dial a number by calling up
the name instead of the full phone number.
Steps
User says
System answer
1
"PHONE"
"PHONE"
2
"STORE NAME"
"STORE NAME"
"NAME PLEASE"
3
"<name>"
"REPEAT NAME PLEASE"
4
"<name>"
"STORING NAME"
"<name> STORED"
"NUMBER PLEASE"
5
"<phone number>"
"<phone number>"
6
"STORE"
"STORING NUMBER"
"<phone number>"
"NUMBER STORED"
Delete name
Stored names can also be deleted from
the directory.
260
Voice control
Steps
User says
System answer
1
"PHONE"
"PHONE"
2
"DELETE NAME"
"NAME PLEASE"
3
"<name>"
"DELETE <name>"
"CONFIRM YES OR NO"
4
"YES"
"<name> DELETED"
"NO"
"COMMAND CANCELLED"
Play directory
Use this function to let the system tell you
all stored entries.
Steps
User says
System answer
1
"PHONE"
"PHONE"
2
"PLAY DIRECTORY"
"PLAY DIRECTORY"
Delete directory
This function allows you to delete all
entries in one go.
Steps
User says
System answer
1
"PHONE"
"PHONE"
2
"DELETE DIRECTORY"
"DELETE DIRECTORY"
"CONFIRM YES OR NO"
3
"YES"
"DIRECTORY DELETED"
"NO"
"COMMAND CANCELLED"
Main settings
Reject calls
Calls can be set to be automatically
rejected using voice control.
261
Voice control
Steps
User says
System answer
1
"PHONE"
"PHONE"
2
"REJECT CALLS"
"REJECT CALLS"
"ACCEPT CALLS"
"ACCEPT CALLS"
*
* use this command to turn the reject mode off
Overview
CLIMATE CONTROL
COMMANDS
The overview below shows the available
voice commands. The following lists will
give further information about the
complete command menu in selected
examples.
Climate
The climate voice commands supports the
functionality of the fan speed, temperature
and mode settings. Not all functions are
available on all vehicles.
"CLIMATE"
"HELP"
*
"FAN"
"DEFROSTING/DEMISTING ON"
*
*
"DEFROSTING/DEMISTING OFF"
"TEMPERATURE"
"AUTO MODE"
*
*
* Can be used as a shortcut. On vehicles fitted with an English language module the "FAN"
shortcut is not available.
Fan
This function allows you to adjust the fan
speed.
262
Voice control
Steps
User says
System answer
1
"CLIMATE"
"CLIMATE"
2
"‘FAN"
"FAN SPEED PLEASE"
"MINIMUM"
"FAN MINIMUM"
"<a number between 1 and 7>"
"FAN <number>"
"MAXIMUM"
"FAN MAXIMUM"
3
*
* Can be used as a shortcut. On vehicles fitted with an English language module the "FAN"
shortcut is not available.
Defrosting/Demisting
Steps
User says
System answer
1
"CLIMATE"
"CLIMATE"
"DEFROSTING ON/DEMISTING
*
2
ON"
"DEFROSTING OFF/DEMISTING
*
OFF"
"DEFROSTING ON/DEMISTING ON"
"DEFROSTING OFF/DEMISTING
OFF"
* Can be used as a shortcut.
Temperature
This function allows you to adjust the
temperature.
Steps
User says
1
"CLIMATE"
2
3
"TEMPERATURE"
System answer
"CLIMATE"
*
"TEMPERATURE PLEASE"
"MINIMUM"
"TEMPERATURE MINIMUM"
"<a number between 15 and 29 °C
with 0.5 increments>" or "<a
number between 59 and 84 °F>"
"TEMPERATURE <number>"
263
Voice control
Steps
User says
System answer
"MAXIMUM"
"TEMPERATURE MAXIMUM"
* Can be used as a shortcut.
Auto mode
Steps
User says
System answer
1
"CLIMATE"
"CLIMATE"
2
"AUTO MODE"
*
"AUTO MODE"
* Can be used as a shortcut. Can be deactivated by selecting a different temperature or
fan speed.
264
Connectivity
The system supports a range of external
devices, to fully integrate with your audio
unit via the USB and auxiliary input
sockets. Once connected, control of the
external device is possible via the audio
unit.
GENERAL INFORMATION
CAUTIONS
Take care when handling external
devices with exposed electrical
connectors (such as the USB plug).
Always replace the protective cap/shield
when possible. There may be a risk of
electrostatic discharge causing damage
to the device.
A list of typical compatible devices are
shown below:
• USB memory sticks
• USB portable hard drives
• Some MP3 players with USB
connection
• iPod media players (refer to
www.ford-mobile
-connectivity.com for latest
compatibility list).
Do not touch or handle the USB
socket in the vehicle. Cover the socket
when not in use.
Only use USB Mass-Storage device
compliant devices.
Always switch your audio unit to a
different source (for example the
radio) before unplugging the USB
device.
The system is USB 2.0 full speed
compatible, USB 1.1 host compliant and
supports FAT 16/32 file systems.
Do not install or connect USB hubs or
splitters.
Information on audio file
structures for external devices
USB
Note: The system is only designed to
recognize and read suitable audio files from
a USB device that conforms to the USB
Mass-Storage device class or an iPod. Not
all available USB devices can be guaranteed
to function with the system.
Create only a single partition on the USB
device.
If playlists are created, they must contain
correct file paths referenced to the USB
device. It is recommended to create the
playlist after the audio files have been
transferred to the USB device.
Note: It is possible to connect compatible
devices with a trailing USB lead as well as
those that plug into the vehicle USB socket
directly (for example USB memory sticks
and pen drives).
Playlists must be created in .m3u format.
Audio files must be in .mp3 format.
Note: Some USB devices with a higher
power consumption may not be compatible
(for example some larger hard drives).
Do not exceed the following limits:
• 1000 items per folder (files, folders and
playlists)
• 5000 folders per USB device (including
playlists)
• 8 subfolder levels.
Note: Access time to read the files on the
external device will vary depending upon
factors such as the file structure, size and
device content.
265
Connectivity
Connection
To enable voice control for custom
playlists and folders, follow the procedure
below:
• Create folders named with the
structure "Ford<*>" where <*> is a
number 1-10. For example "Ford3"
without an extension.
• Create playlists named with the
structure "Ford<*>.m3u" where <*>
is a number 1-10. For example
"Ford5.m3u" without any space
between "Ford" and the number.
Plug in the device, and if necessary secure
it to prevent movement within the vehicle.
Connecting an iPod
For optimum convenience and audio
quality, we recommend that you purchase
a dedicated single connection lead
available from your dealer.
Alternatively, it is possible to connect your
iPod using the standard iPod USB cable
and a separate 3.5mm audio jack lead. If
using this method preset the iPod volume
to maximum and turn off any equalizer
settings before making the connections:
Thereafter, custom folders and playlists
will be selectable with voice control. See
Audio unit commands (page 250).
iPod
•
To enable voice control for custom
playlists, create playlists named with the
structure "Ford<*>" where <*> is a
number 1-10. For example "Ford7" without
any space between "Ford" and the
number.
•
Connect the headphone output of the
iPod to the AUX IN socket.
Connect the USB cable from the iPod
to the vehicle USB socket.
CONNECTING AN EXTERNAL
DEVICE - VEHICLES WITH:
BLUETOOTH
Thereafter, playlists will be selectable with
voice control. See Audio unit commands
(page 250).
Connecting a Bluetooth audio
device
CONNECTING AN EXTERNAL
DEVICE
CAUTION
As various standards exist,
manufacturers are able to implement
a variety of profiles in their Bluetooth
devices. Because of this, an incompatibility
can occur between the Bluetooth device
and the system, which in some cases may
limit system functionality. To avoid this
situation, only recommended devices
should be used.
WARNING
Make sure the external device is
securely mounted within the vehicle,
and that trailing connections do not
obstruct any of the driving controls.
External devices may be connected using
the auxiliary input socket and the USB port.
See Auxiliary input (AUX IN) socket
(page 113). See USB port (page 113).
Please visit the website
www.ford-mobile-connectivity.com
for full details.
266
Connectivity
Bonding the device
Folder
To connect the device to the system follow
the same procedure as for Bluetooth hands
free phones. See Bluetooth setup (page
245).
E100022
Playlist
E100023
Operating the device
Album
Note: The seek buttons and file information
will only work on certain phones and
devices.
E100024
Artist
Select Bluetooth audio as the active
source.
E100025
Filename
1. Select AUX.
2. Press the up and down arrow buttons
to select the desired function.
3. Press the OK button.
E100026
Track title
E100027
Tracks can be accessed by skipping
forwards and backwards using the steering
wheel controls, or directly from the audio
unit controls.
Information not available
E100028
Operation
Audio control
Select the USB device as the audio source
by repeatedly pressing the AUX button
until the USB screen appears in the display.
After first connecting the USB device, the
first track within the first folder will start
to play automatically. Subsequently,
following audio source switching, the
position of playback on the USB device is
remembered.
Press the seek up and down keys to skip
backwards and forwards through tracks.
Press and hold the seek keys to enable fast
rewind/fast forward through track content.
Press the INFO button or function button
4 to display the following:
• Title.
• Artist.
• Album.
• File name.
To browse the device contents, press the
up/down arrow key or the OK button once.
USING A USB DEVICE
Various icons are used to identify types of
audio file, folders etc.
USB device is the active source
E100029
267
Connectivity
The display will show the track
information, together with other important
information described below:
• A vertical scroll bar on the right side of
the display shows the current position
of the folder view.
• ">" after an entry indicates a further
level down is readable (for example a
folder named after an album, with
individual album tracks within that
folder).
• "<" before the list indicates that a
further level up is readable.
• Icons to the left of track/folder text
indicate the type of file/folder. Refer
to the list for an explanation of these
icons.
•
•
folder name
file name.
USING AN IPOD
Various icons are used to identify types of
audio file, folders etc.
iPod is the active source
E100030
iPod playlist
E100031
iPod artist
E100032
iPod album
To navigate the USB device contents, use
the up/down arrow keys to scroll through
lists, and the left/right keys to move up or
down within the folder hierarchy. Once your
desired track, playlist or folder is
highlighted, press the OK button to select
playback.
E100033
iPod genre
E100034
iPod song
Note: If you wish to jump to the top level
of the USB device contents, press and hold
the left arrow key.
E100035
iPod generic category
E100036
Audio control
iPod generic media file
Press the seek up and down keys to skip
backwards and forwards through tracks.
E100037
Press and hold the seek keys to enable fast
rewind/fast forward through track content.
Operation
Connect the iPod. See Connecting an
external device (page 266).
Use the function buttons to enable shuffle,
repeat and scan with respect to the whole
device, folders and playlists.
Select the iPod as the audio source by
repeatedly pressing the AUX button until
the iPod screen appears in the display.
Press the INFO button or function button
4 to display the following:
• title
• artist
• album
268
Connectivity
The iPod menu list for browsing contents
will be available through the radio display.
Navigation of the contents follows the
same principles as for iPod standalone use
(for example search by artist, title, etc.).
To browse the iPod contents, press the
up/down arrow key or the OK button once.
Press the INFO button or function button
4 to display the following:
• title
• artist
• album.
The display will show the track
information, together with other important
information described below:
• A vertical scroll bar on the right side of
the display shows the current position
of the list view.
• ">" after an entry indicates a further
level down is readable (for example all
albums by a particular artist).
• "<" before the list indicates that a
further level up is readable.
• An icon on the left side indicates the
type of the currently displayed list (for
example list of albums). Refer to the
list for an explanation of these icons.
To navigate the iPod contents, use the
up/down arrow keys to scroll through lists,
and the left/right keys to move up or down
within the hierarchy. Once your desired
track, playlist, album, artist or genre is
highlighted, press the OK button to select
playback.
Note: If you wish to jump to the top level
of the iPod contents, press and hold the left
arrow key.
Audio control
Press the seek up and down keys to skip
backwards and forwards through tracks.
Press and hold the seek keys to enable fast
rewind/fast forward through track content.
Use the function buttons to enable shuffle
and repeat with respect to playlists.
Press function button 3 to scan the whole
device or a playlist if it is in operation.
269
Navigation introduction
GENERAL INFORMATION
CAUTIONS
Use only 12 cm (4.7 inches) discs or 8
cm (3.1 inches) discs with a suitable
adaptor.
Press the relevant button on the unit bezel
to access the system functions. This will
take you into the selected mode.
Do not attempt to open the unit. If the
unit malfunctions consult your dealer.
One hour mode
Improper use of settings and
connections, other than those
explained in this handbook, can
damage the unit.
To conserve battery power, the system can
be operated in one hour mode. If the
ignition is off, press the ON/OFF button to
switch the system on. The system will
automatically switch off after one hour.
Do not turn the ignition key or attempt
to start the engine while the software
is updating.
System notes
WARNINGS
The front glass on the liquid crystal
display may break if hit with a hard
object. If the glass breaks, do not
touch the liquid crystalline material. In case
of contact with the skin, wash immediately
with soap and water.
The system is recommended for use when
the ignition key is turned to the accessory
position or when the engine is running. If
the system is used extensively when the
engine is not running, care needs to be
taken to avoid draining the battery.
The unit is a highgrade laser product
which uses an invisible laser beam.
If this is handled incorrectly it can
emit dangerous rays. Do not attempt to
look through any openings in the unit.
ROAD SAFETY
WARNINGS
The system provides you with
information designed to help you
reach your destination quickly and
safely.
CAUTIONS
Irregular shaped CDs and CDs with a
scratch protection film or self
adhesive labels attached should not
be used. Warranty claims, where this type
of disc is found to be inside an audio unit
returned for repair, will not be accepted.
For reasons of safety, the driver
should only program the system
when the vehicle is stationary.
The system provides no assistance
with respect to stop signs, traffic
lights, areas under construction or
other important safety information.
Do not clean the unit with solvents or
aerosol cleaning agents. Use only a
damp cloth.
Do not use the system until you have
familiarised yourself with its
operation.
Do not insert foreign objects into any
of the unit disc drives or media card
slots.
Only view the system display when
driving conditions permit.
Do not insert more than one disc into
the unit disc drive.
270
Navigation introduction
Safety information
Read and follow all stated safety
precautions. Failure to do so may increase
your risk of collision and personal injury.
Ford Motor Company shall not be liable
for any damages of any type arising from
failure to follow these guidelines.
If detailed viewing of route instructions is
necessary, pull off the road when it is safe
to do so and park your vehicle.
Do not use the navigation system to locate
emergency services.
To use the system as effectively and safely
as possible, always use the latest
navigation information. Your dealer will be
able to assist with this.
271
Navigation unit overview
A
Descriptions for function buttons
1-4
Function buttons 1 to 4 are context
dependent, and change according to the
current unit mode. Descriptions for the
functions are shown at the bottom of the
screen display.
1
E104157
2
3
4
A
272
Navigation unit overview
Vehicles with CD-SD navigation system
A
B
C
E
D
F
G
V
U
H
T
S
I
R
J
Q
K
P
N
O
M
L
E129241
A
CD eject.
B
Navigation arrows.
C
CD aperture.
D
OK.
E
Information.
F
Map select. See Route displays (page 284).
G
Menu select. See System settings (page 280).
H
Telephone keypad and station presets. See Audio unit operation (page 235).
See Audio unit menus (page 238). See Telephone (page 245).
I
Clock. See System settings (page 280).
J
Traffic announcement. See Traffic Message Channel (page 285).
K
Function 4.
273
Navigation unit overview
L
Function 3.
M
Seek up. CD track selection. See Station tuning control (page 235). See Track
selection (page 240).
N
On/off and volume control. See On/off control (page 235).
O
Seek down. CD track selection. See Station tuning control (page 235). See
Track selection (page 240).
P
Function 2.
Q
Function 1.
R
Phone select. See Telephone (page 245).
S
Auxiliary select. See Auxiliary input (AUX IN) socket (page 243).
T
Radio select. See Audio unit operation (page 235). See Audio unit menus
(page 238).
U
CD select. See Compact disc player (page 240).
V
Navigation select. See System settings (page 280).
274
Navigation unit overview
Vehicles with Sony CD-SD navigation system
A
B
C
D
E
F
G
Y
X
H
W
I
V
J
U
K
T
L
S
R
Q
P
O
N
M
E129242
A
On/off control. See On/off control (page 235).
B
Navigation select. See System settings (page 280).
C
Telephone keypad and station presets. See Audio unit operation (page 235).
See Audio unit menus (page 238). See Telephone (page 245).
D
CD aperture.
E
Navigation arrows.
F
Map select. See Route displays (page 284).
G
CD eject.
H
Information.
I
Clock. See System settings (page 280).
J
Seek up. CD track selection. end call. See Station tuning control (page 235).
See Track selection (page 240). See Using the telephone (page 246).
275
Navigation unit overview
K
Home select. See System settings (page 280).
L
Traffic announcement. See Traffic Message Channel (page 285).
M
Function 4.
N
Sound select. See Sound button (page 235).
O
Function 3.
P
OK.
Q
Function 2.
R
Menu select. See System settings (page 280).
S
Function 1.
T
Phone select. See Telephone (page 245).
U
Auxiliary select. See Auxiliary input (AUX IN) socket (page 243).
V
Seek down. CD track selection. accept call. See Station tuning control (page
235). See Track selection (page 240). See Using the telephone (page 246).
W
Radio select. See Audio unit operation (page 235). See Audio unit menus
(page 238).
X
CD select. See Compact disc player (page 240).
Y
Volume control.
3. Use the up and down arrow buttons to
select the required feature.
4. Press the OK button to confirm your
selection.
LOADING THE NAVIGATION
DATA
For map updates and system upgrades
please refer to your dealer.
Loading the navigation data
E129900
1.
Load the navigation SD card into the
aperture.
2. Press the NAV button. The road safety
warning will be shown in the display.
276
Navigation Quick start
Vehicles with mobile navigation
system
Installing the micro SD card
CAUTION
Using the system with the engine off
will drain the battery.
1
Note: You will be charged when sending
and receiving text messages.
Note: Refer to your phone handbook for all
phone functions and operation.
2
Note: Keep the activation code (printed on
the installation guide) in a safe place.
Note: Retain the activation text message
in your mobile phone inbox.
E114212
1.
Remove the micro SD card from the
adaptor.
2. Insert the micro SD card into the mobile
phone.
Compatibility of phones
CAUTION
As no common agreement exists,
mobile phone manufacturers are able
to implement a variety of profiles in
their Bluetooth devices. Because of this,
an incompatibility can occur between the
phone and hands-free system, which in
some cases may significantly degrade the
system performance. To avoid this
situation, only recommended phones
should be used.
Activating the mobile phone
navigation system
Note: The radio must be switched on before
connecting the mobile phone to the in-car
GPS receiver.
Note: The Ford Mobile Navigation must be
installed and activated on your mobile
phone.
Note: It is possible to activate up to a
maximum of three phones.
Please visit the website
www.ford-mobile-connectivity.com for
full details.
Note: Detailed instructions are available
on the micro SD card and at
www.ford-mobile-connectivity.com.
To connect the device to the system follow
the same procedure as for Bluetooth hands
free phones. See Bluetooth setup (page
245).
1.
277
Switch the radio on.
Navigation Quick start
3. Press the OK button to activate your
selection.
Selection lists
Various screens are presented which offer
a selection list of available options.
1.
Select the option you require, or if it is
not shown on the screen use the up
and down arrow buttons to view the
remainder of the selection list.
2. Press the OK button to confirm your
selection.
E114213
2. Switch your mobile phone on and start
the "Ford Mobile Navigation".
3. Choose "Select Destination".
4. Choose "Enter Address".
5. Change route options if necessary and
start the route guidance.
6. The vehicle display will show the turn
information. Voice instructions are
heard via the vehicle speakers.
Note: Your mobile phone will display your
current position.
7.
Alphanumeric keypad entry
When it is necessary to enter an address,
a keypad will appear prompting you to
enter a postcode, city, or street.
1.
Use the up, down, left and right arrow
buttons to select the letter or number
that you require.
Note: As you spell the entry the results will
appear in the display.
You are able to exit the application and
continue your route guidance after
restarting the application.
Note: The system will limit your entries to
only those characters which spell a valid
entry.
Vehicles with CD-SD navigation
system or Sony CD-SD navigation
system
2. Press the OK button to activate your
selection.
The system has a large range of features,
yet is easy and intuitive to use. Route
guidance is shown on the display screen.
The screen provides full information for
operating the system through the use of
menus, text screens and map displays.
Screen selections are made by scrolling
through the menus using the up, down, left
and right arrow buttons and pressing the
OK button to activate the desired setting.
Route setting example
Navigation main screen
• To select the navigation system, press
the NAV button. The road safety
caution will be displayed. To use the
system, read the caution and press the
OK button.
Destination input screen
• Use the up and down arrow buttons
and scroll to Destination input.
• Press the OK button to activate your
selection.
Basic operation
1.
Press either the NAV or MENU button
to enter the menu structure.
2. Use the up, down, left and right arrow
buttons and scroll through the various
selection lists.
Note: A list with several options is shown.
278
Navigation Quick start
•
•
•
Starting from the top, select the
country followed by either the
postcode if available or city and street
name.
Use the alphanumeric keypad and
selection lists to select your address
details.
Once sufficient information has been
entered, scroll to Start guidance and
press the OK button to activate your
selection.
Note: If you only need to navigate to a city
centre for example, full address details are
not required.
•
•
The route is now calculated and the
screen returns to the main navigation
screen with instructions on how to
proceed.
Follow the screen information and
voice prompts to reach your
destination.
279
System settings
Most of the important settings for your
navigation unit can be accessed via the
MENU or NAV button. The following
section describes the various options and
how to use them.
Last destinations
This feature allows quick access to a
history of previous destinations entered in
the system. A detailed display will show
the complete stored information including
an overview map. Select the required
repeat destination from the list.
For menu structures: See Information
Displays (page 75).
Menu structure - Information and
entertainment display - Vehicles
with navigation system
Favourites
This feature allows you to customize a
personal destination address book and
assign user defined names to addresses
and locations. A detailed display will show
the complete stored information including
an overview map. Select the required
repeat destination from the list.
Route
This feature allows you to customise the
route to your specific journey requirements
(for example continue route guidance,
block specific sections of your route or
select specific sections of a route).
Points of interest
This feature allows you to customise the
route to your specific journey requirements
(for example select a museum on route or
a specific point of interest near your
destination).
Destination input
This feature allows you to enter your
destination details (for example enter city
names, enter street names or pick a place
from a map).
Tour planning
Traffic
This feature allows you to enter a number
of different destinations and select the
order in which you wish to visit them. You
can also modify an existing tour or recall a
previous tour. The system will
automatically calculate and display your
chosen journey.
This feature allows you to customise how
you receive traffic information (for
example review and sort traffic messages,
review your route or block parts of your
route).
Home address
Store position
This feature allows you to start the route
guidance to your home address or change
the details of your home address.
This feature allows you to store and name
your current position.
Note: On Vehicles with a Sony CD-SD
navigation system, press the HOME button
and the system will automatically start
route guidance to the listed home address.
Route options
This feature allows you to customise the
route to your specific journey requirements
(for example select the fastest or most
economical route or select a route that will
avoid tunnels, seasonal roads and toll
roads).
280
System settings
Special functions
Nav audio mixing
This feature allows you to select GPS and
system information or a demonstration of
the system functionality.
This feature allows you to adjust the
volume mix between the navigation voice
output and audio source.
Map display
DSP settings
This feature allows you to change the way
the map screen is displayed (for example
clean 2D and clean 3D view) and to
customise display information for your
journey (for example time to arrival and
lane guidance).
This feature allows you to customise
speaker output relevant to seat positions.
DSP equaliser
This feature allows you to select the music
category that most suits your listening
preference. The audio output will change
to enhance the particular style of music
chosen.
Assistance options
This feature allows you to customise
display information for your journey (for
example signs, lanes and speed limits).
News
This feature allows you to receive news
bulletins from stations on the FM
waveband or radio data system (RDS) and
enhanced other network (EON) linked
stations, in the same way as traffic
information is provided. You can turn this
on and off.
Personal data
This feature allows you to edit and delete
personal data (for example your home
address).
Reset all settings
This feature allows you to reset the
navigation settings.
Alternative frequencies
This feature will search for and switch to
the strongest station signal when moving
from one transmission area to another.
Menu structure - Information and
entertainment display - All
vehicles
RDS regional
Audio settings
This feature controls the behaviour of AF
switching between regionally related
networks of a parent broadcaster.
Adaptive volume
This feature allows you to adjust the
volume level to compensate for engine and
road speed noise. You can turn this on and
off.
DAB service link
This feature allows you to select stations
that are broadcast on the DAB channels.
Sound
Bluetooth
This feature allows you to adjust the sound
settings (for example bass and treble.
This feature allows you to switch
Bluetooth on or off.
281
System settings
Clock settings
Set time
This feature allows you to manually adjust
the time.
Set date
This feature allows you to manually adjust
the date, month and year.
GPS time
This feature allows you to, if in a suitable
coverage area, automatically adjust the
date and time using GPS.
Set time zone
This feature allows you select a specific
time zone.
Summertime
This feature allows you set the system to
adjust for seasonal time differences.
Note: GPS time must be selected.
24-hour mode
This feature allows you to adjust the
system between 12 and 24-hour mode.
282
Navigation system
ROUTE OPTIONS MENU
Eco settings
You can set a number of options which
alter the way a route is planned.
Trailer
Use this feature to change the economy
settings of your journey relating to whether
or not you are towing a trailer and if so the
size of trailer being towed.
Using the up, down, left and right arrow
buttons, you can select from the list which
road features are to be avoided or included
in the route by turning the feature on or off.
Roof box
Route
Eco
Use this feature to change the economy
settings of your journey relating to the use
of a roof box.
This option will prioritise the most
economical route to the destination.
Dynamic
Short
When switched on, and if the unit is
receiving a valid traffic message channel
(TMC) signal, the route will be
automatically updated to take into
account real time traffic incidents or
congestion.
This option will prioritise the shortest route
to the destination..
Note: This feature can be useful in avoiding
delays or hold ups on journeys.
Always ask
Motorway
Use this feature to make sure that you are
always given the choice of route type
selection for your journey.
When switched on the system will look for
motorways on your route and
automatically update your route distance
and timings.
Fast
This option will prioritise the fastest route
to the destination.
Driver
Note: This feature can be useful in avoiding
delays or hold ups on journeys.
Leisurely
This option will prioritise the route for a
leisurely driver to the destination.
Ferry/motorail
When switched on the system will look for
ferry crossings and motorail facilities on
your route and automatically update your
route distance and timings.
Normal
This option will prioritise the route for a
normal driver to the destination.
Toll
Fast
When switched on the system will look for
toll roads on your route and automatically
update your route distance and timings.
This option will prioritise the route for a
fast driver to the destination.
283
Navigation system
Seasonal roads
Junction zoom
When switched on the system will look for
seasonal roads on your route and
automatically update your route distance
and timings.
This feature will automatically increase
the zoom on the map display at times
when you are required to make a turn, or
perform more complex manoeuvres.
Shortly after the zoom scale will return to
the previous level.
Note: This feature can be useful in avoiding
delays or hold ups on journeys.
Select AUTO to activate junction zoom.
Toll sticker
Navigation display
When switched on the system will
automatically select toll roads and update
your route distance and timings.
After commencing a navigation route, the
default screen is the main navigation
screen:
ROUTE DISPLAYS
Once an active route is underway, guidance
will be given by on-screen information and
voice prompts. Whichever audio source
you wish to leave the unit in, basic turn by
turn and distance information will remain
on the screen in the form of a graphic inset.
You do not need to leave the unit on the
main navigation screen when you are
navigating a route. Slightly more detailed
information on your route may be available
via the main navigation screen if required.
Map display
Press the MAP button for a map view.
This view will show your current location
with your vehicle in the centre shown as
an arrow surrounded by a circle. The arrow
will face in the direction of travel.
The information on the top line gives the
name of the current road, or the next road
to take if a turn is approaching.
WARNING
Do not rely on the screen prompts
when navigating. Always listen to the
navigation voice and take care not
be distracted from the road ahead.
You can change the way the map is
displayed by altering the zoom and
orientation settings. Press the relevant
function buttons to change the map scale
and using the left and right arrow buttons
zoom in or out. The current map scale is
shown on the display.
Map scale settings may be set between
50 metres to 500 kilometres or 0.05 miles
to 500 miles, with an auto setting to the
far left. The auto setting continuously
changes the map scale according to the
road type being driven.
284
Traffic Message Channel
You may either select a view which shows
messages only affecting your programmed
route, or a view which shows all messages
received. Press function button 1 to change
the view.
PRINCIPLE OF OPERATION
Traffic message channel (TMC) stations
are broadcast on the FM waveband. TMC
is a feature that receives traffic alerts
which can be used to plan alternative
routes and avoid hold ups.
USING TMC
Press the TA or TRAFFIC button to show
the traffic menu page.
Traffic announcement
Traffic announcement (TA) can be turned
on or off via this menu. If switched on a TA
indicator is shown in the information
border of the status bar.
Stations which broadcast on the FM
waveband and carry traffic programme
(TP) information are identified by TP
shown in the screen display. With TA
switched on the unit will respond to these
announcements and interrupt music
playback. After the announcement has
ended music playback will resume.
Ending traffic announcements
The unit will return to normal operation at
the end of each traffic announcement. To
end the announcement prematurely, press
the TA, TRAFFIC, RADIO or CD button
during the announcement.
Using TMC messages
Select the required item to display a list of
TMC messages. See General
Information (page 75). This is only an
overview display which gives very basic
information. Select the message you
require further information on and another
screen will be displayed giving full message
details on incident location etc.
285
Map updates
The road network is constantly changing
due to new roads, changes in road
classification, etc. Therefore, it is not
always possible to exactly match the map
data in the system to the current road
network.
Map information is regularly updated, but
all areas are not necessarily covered to the
same level of detail. Some roads, in
particular private roads, may not be
included on the database. To help with
accuracy, always use the latest version
navigation disc. Your dealer will be able to
provide this.
286
Appendices
www.novero.com/declaration_of_conformity
TYPE APPROVALS
The Bluetooth word mark and logos are
owned by the Bluetooth SIG, Inc. and any
use of such marks by Ford Motor Company
is under license. Other trademarks and
trade names are those of their respective
owners.
FCC/INDUSTRY CANADA NOTICE
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
TYPE APPROVALS
iPod is a trademark of Apple Inc.
FCC ID: WJLRX-42
TYPE APPROVALS
IC: 7847A-RX42
Changes or modifications to your device
not expressly approved by the party
responsible for compliance can void the
user's authority to operate the equipment.
RX-42 - declaration of conformity
E114214
We, the party responsible for compliance,
declare under our sole responsibility that
the Handset Integration product RX-42 is
in conformity with the provisions of the
following Council Directive: 1999/5/EC. A
copy of the Declaration of Conformity can
be found at:
© 2008 NAVTEQ B.V. All rights reserved.
287
Appendices
E114220
TYPE APPROVALS
TYPE APPROVALS
Laser sensor
E97713
E97714
SD Logo is a trademark.
E132582
288
Appendices
WARNINGS
Invisible laser radiation. Do not view
directly with optical instruments
(magnifiers). Class 1M laser product.
WARNINGS
IEC 60825-1: 1993 + A2:2001.
Complies with FDA performance
standards for laser products except
for deviation pursuant to Laser Notice No.
50, dated July 26th, 2001.
Item
Specification
Max average power
45mW
Pulse duration
33ns
Wavelength
905nm
ELECTROMAGNETIC
COMPATIBILITY
TYPE APPROVALS
EU Declaration
WARNINGS
Your vehicle has been tested and
certified to legislations relating to
electromagnetic compatibility
(72/245/EEC, UN ECE Regulation 10 or
other applicable local requirements). It is
your responsibility to ensure that any
equipment you have fitted complies with
applicable local legislations. Have any
equipment fitted by properly trained
technicians.
Hereby, Valeo declares that this short
range device is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
Certificate for United Arab
Emirates
The RF (radio frequency) transmitter
equipment (e.g. cellular telephones,
amateur radio transmitters etc.) may
only be fitted to your vehicle if they comply
with the parameters shown in the table
below. There are no special provisions or
conditions for installations or use.
E125209
Do not mount any transceiver,
microphones, speakers, or any other
item in the deployment path of the
airbag system.
Do not fasten antenna cables to
original vehicle wiring, fuel pipes and
brake pipes.
289
Appendices
WARNINGS
Keep antenna and power cables at
least 10 centimetres (4 inches) from
WARNINGS
any electronic modules and airbags.
1
2
3
4
E85998
Frequency Band Maximum output power Watt (Peak
MHz
RMS)
Antenna Positions
1 – 30
50 W
3, 4
30 – 54
50 W
1, 2, 3
68 – 87.5
50 W
1, 2, 3
142 – 176
50 W
1, 2, 3
380 – 512
50 W
1, 2, 3
806 – 940
10 W
1, 2, 3
1200 – 1400
10 W
1, 2, 3
1710 – 1885
10 W
1, 2, 3
1885 – 2025
10 W
1, 2, 3
Note: After the installation of RF
transmitters, check for disturbances from
and to all electrical equipment in the
vehicle, both in the standby and transmit
modes.
Check all electrical equipment:
• with the ignition ON
• with the engine running
• during a road test at various speeds.
290
Appendices
Check that electromagnetic fields
generated inside the vehicle cabin by the
transmitter installed do not exceed
applicable human exposure requirements.
291
292
Index
A
Audible Warnings and Indicators..............73
Automatic transmission.....................................73
Door open................................................................74
Frost...........................................................................73
Key outside car......................................................73
Lights on...................................................................74
Low fuel....................................................................74
Seat belt reminder...............................................74
Switching the chimes on and off....................73
A/C
See: Climate Control..........................................94
About This Manual...........................................7
ABS
See: Brakes............................................................132
ABS driving hints
See: Hints on Driving With Anti-Lock
Brakes.................................................................132
Audio Control....................................................41
Type 1.........................................................................41
Type 2.......................................................................42
ACC
See: Adaptive cruise control (ACC)............148
Audio introduction.......................................227
Audio system security................................234
Audio troubleshooting...............................244
Audio unit commands...............................250
Accessories
See: Parts and Accessories.................................7
See: Using Adaptive Cruise Control............150
Active City Stop.............................................162
Auxiliary input.....................................................254
CD Player..............................................................250
External devices - iPod....................................256
External devices - USB....................................254
Radio........................................................................251
Principle of Operation.......................................162
Active Park Assist.........................................143
Principle of Operation.......................................143
Adaptive cruise control (ACC)................148
Principle of Operation.......................................148
Audio unit menus........................................238
Audio unit operation...................................235
Audio unit overview....................................228
Auto-Dimming Mirror...................................66
Autolamps........................................................48
Automatic Climate Control........................97
Adaptive cruise control (ACC)
See: Using Adaptive Cruise Control............150
Adjusting the Headlamps - Vehicles
With: Adaptive Front Lighting/Xenon
Headlamps.....................................................51
Adjusting the Steering Wheel.....................41
Air Conditioning
Air distribution.......................................................99
Blower......................................................................98
Cooling the interior quickly...............................99
Mono mode............................................................98
Recirculated air.....................................................99
Setting the temperature...................................98
Switching off the automatic climate
control.................................................................99
Switching the air conditioning on and
off..........................................................................99
To switch mono mode back on......................98
To switch mono mode off................................98
Windscreen defrosting and demisting........99
See: Climate Control..........................................94
Air Vents............................................................94
Centre air vents.....................................................94
Side air vent...........................................................95
Alarm..................................................................39
Principle of Operation........................................39
Alternative frequencies.............................238
Appendices....................................................287
Arming the alarm...........................................40
Arming the engine immobiliser................38
At a Glance........................................................10
Front exterior overview.......................................10
Instrument panel overview................................12
Rear exterior overview.........................................15
Vehicle interior overview......................................11
Automatic Main Beam Control.................48
Activating the system.........................................49
Manually overriding the system.....................50
Setting the system sensitivity.........................49
293
Index
C
Automatic Transmission............................129
Emergency park position release
lever......................................................................131
Hints on driving with an automatic
transmission....................................................130
Selector lever positions....................................129
Sport mode and manual shifting.................130
Capacities and Specifications................223
Technical Specifications.................................223
Cargo Nets......................................................165
Cargo net...............................................................166
Luggage retention net.......................................165
Automatic volume control.......................238
Autostore control.........................................236
Autowipers........................................................43
Auxiliary Heater.............................................102
Car Wash
See: Cleaning the Exterior..............................204
Catalytic Converter......................................124
Driving with a catalytic converter.................124
Diesel auxiliary heater (depending on
country)............................................................104
Fuel operated heater (depending on
country)............................................................104
Parking heater......................................................102
Changing a Bulb.............................................55
Approach lamp......................................................57
Central high mounted brake lamp.................61
Front fog lamps....................................................58
Headlamp...............................................................55
Interior lamps.........................................................61
Luggage compartment lamp, footwell lamp
and tailgate lamp.............................................61
Number plate lamp..............................................61
Rear lamps - 4 door............................................59
Rear lamps - 5 door............................................58
Side repeater..........................................................57
Auxiliary input (AUX IN) socket................113
Auxiliary Power Points..................................111
B
Battery connection points........................207
Blind Spot Monitor........................................66
Blind spot information system (BLIS).........66
Detection errors....................................................68
System detection and alerts............................67
Turning the system on and off.........................67
Using the system.................................................66
Changing a Fuse............................................179
Changing a Road Wheel...........................208
Assembling the wheel brace.........................210
Installing a road wheel......................................212
Jacking and lifting points................................209
Locking wheel nuts...........................................208
Removing a road wheel.....................................211
Removing the wheel trim..................................211
Vehicle jack..........................................................208
Vehicles with a spare wheel.........................208
Bluetooth setup...........................................245
Handling of phones..........................................245
Requirements for Bluetooth
connection.......................................................245
Bonnet Lock
See: Opening and Closing the Bonnet.......190
Changing the remote control
battery.............................................................29
Booster cables
See: Jump-Starting the Vehicle...................206
Booster cushion (Group 3)...............................20
Booster seat (Group 2)......................................20
Remote control with a folding key
blade....................................................................29
Remote control without a folding key
blade....................................................................30
Brake and Clutch Fluid Check................200
Brakes................................................................132
Changing the Vehicle Battery..................207
Changing the Wiper Blades.......................45
Principle of Operation.......................................132
Rear window wiper blade.................................46
Windscreen wiper blades.................................45
Booster Seats..................................................20
Bulb changing
See: Changing a Bulb..........................................55
Checking the Wiper Blades........................45
Childminder Mirror.........................................112
Child Safety........................................................17
Bulb Specification Chart.............................62
294
Index
D
Child Safety Locks..........................................22
Electric child safety locks..................................22
Manual child safety locks..................................22
Diesel Particulate Filter...............................118
Child Seat Positioning...................................18
Child Seats.........................................................17
Regeneration.........................................................118
Digital signal processing (DSP).............238
Child restraints for different mass
groups...................................................................17
Changing the DSP settings............................238
DSP equaliser......................................................238
DSP occupancy..................................................238
Cigar Lighter......................................................111
Cleaning the Exterior..................................204
Direction Indicators........................................52
Disabling the passenger airbag.................27
Body paintwork preservation.......................204
Cleaning the chrome trim..............................204
Cleaning the headlamps................................204
Cleaning the rear window..............................204
Disabling the passenger airbag......................28
Enabling the passenger airbag.......................28
Fitting the passenger airbag deactivation
switch...................................................................27
Cleaning the Interior...................................204
Instrument cluster screens, LCD screens,
radio screens..................................................205
Rear windows.....................................................205
Seat belts.............................................................204
Disarming the alarm.....................................40
Vehicles with keyless entry..............................40
Vehicles without keyless entry.......................40
Disarming the engine immobiliser...........38
Dog Guard.......................................................166
Climate Control..............................................94
Principle of Operation........................................94
Installing behind the front seats..................166
Installing behind the rear seats.....................167
Climate control commands....................262
Climate..................................................................262
DPF
Clock....................................................................111
Coded keys.......................................................38
Cold Weather Precautions........................176
Compact disc playback............................240
Compact disc player..................................240
Compact disc track scanning..................241
See: Diesel Particulate Filter...........................118
Driver Alert......................................................154
Principle of Operation.......................................154
Driving Hints....................................................176
Driving Through Water................................176
Driving through water .......................................176
Type 1.......................................................................241
Type 2 and 3..........................................................241
E
Connecting an external device...............266
Connection..........................................................266
Eco Mode.........................................................122
Connecting an external device - Vehicles
With: Bluetooth.........................................266
Electric exterior mirrors................................65
Connecting a Bluetooth audio
device................................................................266
Electric folding mirrors.......................................65
Mirror tilting positions.........................................65
Connectivity...................................................265
Electric sunroof.............................................100
General Information.........................................265
Opening and closing the sunroof..................101
Opening and closing the sunroof
automatically...................................................101
Sunroof anti-trap protection..........................101
Sunroof relearning.............................................102
Sunroof safety mode........................................102
Tilting the sunroof...............................................101
Principle of Operation.......................................122
Convenience features...................................111
Coolant Check
See: Engine Coolant Check............................199
Cornering Lamps............................................52
Cruise Control................................................146
Principle of Operation.......................................146
Cruise control
Electromagnetic compatibility..............289
Ending compact disc playback..............242
Engine Block Heater.....................................119
See: Using Cruise Control................................146
Cup Holders.....................................................112
Rear seat armrest................................................112
295
Index
Engine Coolant Check................................199
Fuse Box Locations......................................178
Checking the coolant level.............................199
Topping up............................................................199
Engine compartment fuse box......................178
Load compartment fuse box.........................178
Passenger compartment fuse box...............178
Engine immobiliser........................................38
Fuses.................................................................178
Fuse Specification Chart...........................180
Principle of Operation........................................38
Engine Oil Check..........................................198
Checking the oil level........................................199
Topping up............................................................199
Engine compartment fuse box.....................180
Load compartment fuse box.........................185
Passenger compartment fuse box..............183
Engine Oil Dipstick - 1.6L Duratec-16V
Ti-VCT (Sigma).........................................198
Engine Oil Dipstick - 1.6L Duratorq-TDCi
(DV) Diesel/2.0L Duratorq-TDCi (DW)
Diesel.............................................................198
Engine Oil Dipstick - 1.6L EcoBoost SCTi
(Sigma).........................................................198
Engine Oil Dipstick - 2.0L Duratec-HE
(MI4)..............................................................198
Exterior Mirrors................................................64
G
Gauges...............................................................69
Engine coolant temperature gauge...............70
Fuel gauge...............................................................70
Gearbox
See: Transmission..............................................129
General Information on Radio
Frequencies...................................................29
Glasses Holder................................................112
Global Opening and Closing......................36
Manual folding mirrors.......................................64
F
Global closing........................................................36
Global opening......................................................36
Fastening the seat belts..............................25
Fast forward/reverse..................................240
First Aid Kit.......................................................177
Floor Mats.........................................................113
Fog Lamps - Front
H
Handbrake
See: Front Fog Lamps........................................50
See: Parking Brake..............................................132
Fog Lamps - Rear
Hazard Warning Flashers.............................51
Headlamp adjustment
See: Rear Fog Lamps.........................................50
Forward alert function................................152
See: Adjusting the Headlamps - Vehicles With:
Adaptive Front Lighting/Xenon
Headlamps.........................................................51
Adjusting the warning sensitivity..................152
Switching the system on and off..................152
Front Fog Lamps............................................50
Fuel and Refuelling......................................123
Headlamp Levelling.......................................51
Recommended headlamp levelling switch
positions..............................................................51
Technical Specifications...................................127
Fuel Burning Heater
See: Auxiliary Heater.........................................102
Headlamp Washers......................................45
Head Restraints............................................106
Fuel Consumption........................................127
Fuel Consumption
Adjusting the head restraint..........................106
Removing the head restraint..........................107
See: Technical Specifications.........................127
Heated Seats..................................................110
Heated Windows and Mirrors.................100
Fuel filler flap..................................................124
Refuelling with a fuel can................................126
Heated exterior mirrors....................................100
Heated windows................................................100
Fuel Quality - Diesel.....................................123
Heating
Long-term storage.............................................124
Fuel Quality - E85.........................................123
See: Climate Control..........................................94
Hill launch assist (HLA)
Long-term storage..............................................123
Fuel Quality - Petrol.....................................123
See: Using hill start assist...............................134
296
Index
Hill Start Assist..............................................134
Instrument Lighting Dimmer......................111
Interior Lamps.................................................53
Principle of Operation.......................................134
Hints on Driving With Anti-Lock
Brakes.............................................................132
HLA
Ambient lighting...................................................53
Interior lighting......................................................53
Introduction.........................................................7
iPod connection
See: Hill Start Assist..........................................134
See: Using hill start assist...............................134
See: Connecting an external device...........266
See: Connecting an external device - Vehicles
With: Bluetooth.............................................266
I
iPod
Ignition Switch................................................114
Immobiliser
See: Using an iPod............................................268
ISOFIX Anchor Points....................................21
See: Engine immobiliser....................................38
Attaching a child seat with top tethers.........21
Top tether anchor points - 4 door
vehicles.................................................................21
Top tether anchor points - all vehicles..........21
Important audio information...................227
Audio unit labels.................................................227
Disc labels.............................................................227
Information Displays.....................................75
J
General Information............................................75
Information Messages.................................83
Jump starting
Active City Stop....................................................84
Airbag.......................................................................84
Alarm........................................................................84
Automatic main beam control.......................84
Battery and charging system...........................85
Blind spot monitor...............................................85
Child power lock...................................................85
Climate control.....................................................85
Cruise control and Adaptive cruise control
(ACC)...................................................................86
Doors open.............................................................86
Driver alert..............................................................86
Engine immobiliser..............................................87
Hill start assist.......................................................87
Keyless entry..........................................................87
Lane keeping aid..................................................88
Lighting....................................................................88
Maintenance..........................................................89
Message indicator................................................83
Occupant protection..........................................89
Parking aid..............................................................89
Parking brake.........................................................90
Power steering......................................................90
Stability control (ESP)......................................90
Starting the engine.............................................90
Start-stop................................................................91
Transmission..........................................................92
Tyre pressure monitoring system...................93
See: Jump-Starting the Vehicle...................206
Jump-Starting the Vehicle.......................206
To connect the booster cables....................206
To start the engine............................................207
K
Keyless Entry....................................................34
Disabled keys.........................................................35
General information............................................34
Locking and unlocking the doors with the
key blade............................................................36
Locking the vehicle..............................................34
Passive key..............................................................34
Unlocking the vehicle..........................................35
Keyless Starting.............................................116
Failure to start.......................................................117
Ignition on...............................................................117
Starting a diesel engine.....................................117
Starting with automatic transmission.........117
Starting with manual transmission...............117
Stopping the engine when the vehicle is
moving................................................................118
Stopping the engine with the vehicle
stationary...........................................................118
Keys and Remote Controls.........................29
Instrument Cluster........................................69
297
Index
L
Manual Seats.................................................105
Adjusting the angle of the seatback...........106
Adjusting the height of the driver’s
seat.....................................................................106
Adjusting the lumbar support.......................106
Moving the seats backwards and
forwards............................................................105
Lane Departure Warning...........................156
Principle of Operation.......................................156
Lane Keeping Aid..........................................158
Principle of Operation.......................................158
Lighting Control...............................................47
Manual Transmission..................................129
Headlamp flasher.................................................47
Home safe lighting..............................................48
Lighting control positions..................................47
Main and dipped beam......................................47
Parking lamps........................................................47
Selecting reverse gear.......................................129
Map updates.................................................286
Message Centre
See: Information Displays.................................75
Mirrors
Lighting...............................................................47
Load Carriers
See: Heated Windows and Mirrors..............100
See: Windows and Mirrors................................63
See: Roof Racks and Load Carriers.............168
MP3 connection
Load Carrying.................................................164
Loading the navigation data..........................276
See: Connecting an external device...........266
See: Connecting an external device - Vehicles
With: Bluetooth.............................................266
Locking and Unlocking.................................32
MP3 display options....................................241
General Information..........................................164
Loading the navigation data....................276
CD text display options....................................242
Double locking.......................................................32
Locking.....................................................................32
Locking and unlocking confirmation.............33
Locking and unlocking the doors from
inside....................................................................33
Locking the doors individually with the
key.........................................................................33
Luggage compartment lid................................33
Unlocking.................................................................32
MP3 file playback.........................................241
Playing a multi session disc............................241
N
Navigation introduction.............................270
General Information.........................................270
Navigation Quick start................................277
Vehicles with CD-SD navigation system or
Sony CD-SD navigation system..............278
Vehicles with mobile navigation
system................................................................277
Locks...................................................................32
Luggage Anchor Points..............................164
Luggage Covers.............................................164
M
Navigation system.......................................283
Navigation unit overview...........................272
Vehicles with CD-SD navigation
system...............................................................273
Vehicles with Sony CD-SD navigation
system...............................................................275
Maintenance..................................................190
General Information..........................................190
Technical Specifications..................................201
Manual Climate Control..............................95
News broadcasts.........................................238
Air conditioning.....................................................96
Air distribution control.......................................95
Blower......................................................................96
Heating the interior quickly..............................96
Recirculated air.....................................................96
Ventilation..............................................................96
O
Occupant protection.....................................24
Principle of Operation.........................................24
Oil Check
See: Engine Oil Check.......................................198
On/off control...............................................235
298
Index
Opening and Closing the Bonnet...........190
Rear Window Wiper and Washers...........44
Closing the bonnet..............................................191
Opening the bonnet..........................................190
Intermittent wipe.................................................44
Rear window washer..........................................45
Reverse gear wipe................................................45
P
Principle of Operation.......................................136
Refuelling - E85.............................................126
Refuelling.........................................................126
Regional mode (REG)................................239
Remote control battery
Parking Brake..................................................132
Parts and Accessories.....................................7
See: Changing the remote control
battery.................................................................29
Parking Aids....................................................136
Remote control programming
Look for the Ford logo on the following
parts .......................................................................8
Now you can be sure that your Ford parts
are Ford parts.......................................................7
See: Programming the remote control........29
Removing a Headlamp................................54
Repairing Minor Paint Damage..............205
Repeat compact disc tracks...................240
Personalised Settings..................................82
Chime deactivation.............................................83
Language setting..................................................82
Measure units........................................................83
Temperature units...............................................83
Type 1.....................................................................240
Type 2 and 3........................................................240
Retractable tow ball....................................170
Driving with a trailer............................................172
Fault conditions...................................................172
Maintenance.........................................................172
Releasing the tow ball arm.............................170
Swivelling the tow ball arm in........................172
Swivelling the tow ball arm out......................171
Power Door Locks
See: Locking and Unlocking.............................32
Power Seats...................................................108
Power Windows..............................................63
Anti-trap function................................................63
Driver's door switches........................................63
Global opening and closing.............................63
Opening and closing the windows
automatically....................................................63
Resetting the memory of the electric
windows.............................................................64
Safety switch for rear windows......................63
Road Safety...................................................270
Safety information..............................................271
Roadside Emergencies................................177
Roof Racks and Load Carriers.................168
Installing the crossbars....................................168
Roof rack...............................................................168
Route displays..............................................284
Programming the remote control............29
Junction zoom....................................................284
Map display.........................................................284
Navigation display.............................................284
Programming a new remote control............29
Reprogramming the unlocking
function...............................................................29
Route options menu...................................283
Folding the rear seatbacks forwards..........109
Folding the seatbacks up.................................110
Folding the seat cushions and the rear
seatbacks forwards......................................109
Driver......................................................................283
Dynamic................................................................283
Eco settings.........................................................283
Ferry/motorail.....................................................283
Motorway..............................................................283
Route......................................................................283
Seasonal roads..................................................284
Toll...........................................................................283
Toll sticker............................................................284
Rear view camera........................................140
Running-In.......................................................176
Principle of Operation......................................140
Brakes and clutch...............................................176
Engine......................................................................176
Tyres.........................................................................176
R
Rear Fog Lamps.............................................50
Rear Seats.......................................................109
299
Index
S
Steering Wheel Lock....................................114
Vehicles with keyless starting.........................114
Vehicles without keyless starting..................114
Safety Precautions.......................................123
Satellite Navigation Unit Holder..............113
Adjusting the holder............................................113
Steering Wheel................................................41
Sunroof
Seat belt height adjustment......................26
Seat belt reminder.........................................26
Switching Off the Engine............................119
Deactivating the seat belt reminder..............27
Rear seat belt reminder......................................27
Symbols Glossary.............................................7
See: Electric sunroof.........................................100
Vehicles with a turbocharger..........................119
Symbols in this handbook...................................7
Symbols on your vehicle.......................................7
Seat belts
See: Fastening the seat belts...........................25
System settings...........................................280
Seats.................................................................105
Security code.................................................234
Shuffle/random...........................................240
Audio settings......................................................281
Clock settings......................................................282
Menu structure - Information and
entertainment display - All
vehicles..............................................................281
Menu structure - Information and
entertainment display - Vehicles with
navigation system........................................280
Type 1.....................................................................240
Type 2 and 3........................................................240
Sitting in the Correct Position..................105
Snow Chains
See: Using Snow Chains...................................217
Sound button................................................235
Speed Control
T
See: Cruise Control............................................146
Speed Limiter.................................................153
Technical Specifications
Principle of Operation.......................................153
Stability Control............................................133
See: Capacities and Specifications............223
Principle of Operation.......................................133
Telephone commands...............................257
Cold or hot engine...............................................116
Create a phonebook........................................260
Main settings........................................................261
Phone......................................................................257
Phone functions.................................................258
Starting and Stopping the Engine...........114
Telephone controls.....................................246
Starter Switch
See: Ignition Switch............................................114
Starting a Diesel Engine..............................116
General Information...........................................114
Remote control..................................................246
Starting a Petrol Engine - E85..................115
Telephone setup..........................................245
Starting at low ambient temperatures
...............................................................................116
Bond another Bluetooth phone...................246
Making a phone an active phone................246
Phonebook...........................................................245
Phonebook categories.....................................246
Starting a Petrol Engine..............................115
Cold or hot engine...............................................115
Engine idle speed after starting.....................115
Flooded engine.....................................................115
Telephone.......................................................245
General Information.........................................245
Telephone
Start-Stop.......................................................120
See: Using the telephone...............................246
Principle of Operation.......................................120
Station preset buttons..............................236
Station tuning control................................235
DAB service linking............................................235
Manual tuning.....................................................235
Scan tuning..........................................................235
Seek tuning..........................................................235
300
Index
Tow Ball............................................................173
Tyre Pressures
Driving with a trailer...........................................174
Driving without a trailer.....................................175
Inserting the tow ball arm................................174
Maintenance.........................................................175
Removing the tow ball arm.............................175
Unlocking the tow ball arm
mechanism.......................................................173
See: Technical Specifications........................218
Tyre Repair Kit................................................213
Checking the tyre pressure..............................215
General information...........................................213
Inflating the tyre..................................................214
Using the tyre repair kit.....................................213
Tyres
Towing a Trailer.............................................170
See: Wheels and Tyres....................................208
Steep gradients...................................................170
U
Towing Points................................................188
Installing the towing eye.................................188
Towing eye location...........................................188
Under Bonnet Overview - 1.6L
Duratec-16V Ti-VCT (Sigma)...............192
Under Bonnet Overview - 1.6L
Duratorq-TDCi (DV) Diesel...................194
Under Bonnet Overview - 1.6L EcoBoost
SCTi (Sigma)..............................................193
Under Bonnet Overview - 2.0L
Duratec-HE (MI4).....................................195
Under Bonnet Overview - 2.0L
Duratorq-TDCi (DW) Diesel..................197
USB port............................................................113
USB
Towing the Vehicle on Four
Wheels..........................................................188
All vehicles............................................................188
Vehicles with automatic
transmission....................................................189
Towing...............................................................170
Track selection.............................................240
Type 2 and 3........................................................240
Traffic information control.......................236
Activating traffic announcements..............236
Ending traffic announcements.....................237
Traffic announcement volume......................237
See: Using a USB device.................................267
Traffic Message Channel..........................285
Using Active City Stop................................162
Principle of Operation......................................285
Switching the system on and off..................163
Traffic Sign Recognition............................160
Using active park assist..............................143
Using Adaptive Cruise Control................150
Principle of Operation......................................160
Transmission..................................................129
Trip Computer.................................................82
Automatic deactivation.....................................151
Changing the set speed...................................150
Setting a speed...................................................150
Setting the vehicle gap....................................150
Switching the system off..................................151
Switching the system on.................................150
Temporarily deactivating the system...........151
Average fuel consumption...............................82
Average speed.......................................................82
Distance to empty...............................................82
Instantaneous fuel consumption..................82
Odometer................................................................82
Outside air temperature....................................82
Resetting the trip computer.............................82
Trip Odometer.......................................................82
Using an iPod................................................268
Audio control.......................................................269
Operation.............................................................268
Type approvals.............................................287
Using a USB device.....................................267
Certificate for United Arab Emirates..........289
EU Declaration...................................................289
FCC/INDUSTRY CANADA NOTICE.............287
Laser sensor........................................................288
RX-42 - declaration of conformity..............287
Audio control......................................................268
Operation..............................................................267
Tyre Care..........................................................216
Tyre Pressure Monitoring System...........217
System reset.........................................................218
301
Index
Using Cruise Control...................................146
Using the speed limiter...............................153
Cancelling the set speed.................................146
Changing the set speed...................................146
Resuming the set speed...................................147
Setting a speed...................................................146
Switching cruise control off............................147
Switching cruise control on............................146
Intentionally exceeding the set speed
limit.....................................................................153
Setting the speed limit.....................................153
Switching the system on and off..................153
System warnings................................................153
Using the telephone...................................246
Using driver alert...........................................154
Using Eco mode............................................122
Changing the active phone............................248
Debonding a bonded phone.........................248
Making a call........................................................247
Muting the microphone..................................248
Receiving an incoming call............................248
Receiving a second incoming call...............248
Resetting Eco mode...........................................122
Using TMC......................................................285
Using hill start assist...................................134
Ending traffic announcements....................285
Traffic announcement.....................................285
Using TMC messages......................................285
Resetting the system........................................155
Switching the system on and off..................154
System display....................................................155
System warnings................................................154
Activating the system.......................................134
Deactivating the system..................................134
Vehicles with manual transmission
only......................................................................134
Using traffic sign recognition...................160
Setting the system speed warning..............160
Switching the system on and off.................160
System display....................................................160
Using lane departure warning.................156
Setting the steering wheel vibration
level.....................................................................157
Setting the system sensitivity........................157
Switching the system on and off..................156
System warnings.................................................157
Using voice control.....................................249
Name tag..............................................................250
System operation..............................................249
Using Winter Tyres........................................217
Using seat belts during pregnancy...........27
Using Snow Chains.......................................217
V
Vehicles with stability control (ESP)...........217
Using Stability Control................................133
Using start-stop............................................120
Vehicle battery.............................................206
Vehicle Care..................................................204
Vehicle Identification Number................222
Vehicle Identification Plate.......................221
Vehicle identification...................................221
Vehicle recovery............................................188
Ventilation
To re-start the engine.........................................121
To stop the engine..............................................120
Using the lane keeping aid........................158
Switching the system on and off..................158
System warnings................................................159
Using the Parking Aid - Vehicles With:
Front and Rear Parking Aid.....................137
See: Climate Control..........................................94
Vents
Manoeuvring with the parking aid...............138
Switching the parking aid on and off...........137
See: Air Vents........................................................94
VIN
Using the Parking Aid - Vehicles With:
Rear Parking Aid.........................................136
Using the Rear View Camera...................140
See: Vehicle Identification Number.............222
Voice control.................................................249
Principle of Operation......................................249
Voice Control...................................................42
Activating the rear view camera...................140
Deactivating the rear view camera..............142
Using the display..................................................141
Vehicles with parking aid.................................142
302
Index
W
Warning Lamps and Indicators..................71
ABS warning lamp................................................71
Airbag warning lamp............................................71
Blind spot monitor indicator..............................71
Brake system lamp...............................................71
Cruise control indicator.......................................71
Direction indicators...............................................71
Engine warning lamp...........................................71
Forward alert warning indicator......................72
Front fog lamp indicator.....................................72
Frost warning lamp..............................................72
Glow plug indicator..............................................72
Headlamp indicator.............................................72
Ignition warning lamp.........................................72
Lane departure warning indicator..................72
Low fuel level warning lamp.............................72
Low tyre pressure warning lamp.....................72
Main beam indicator............................................72
Message indicator.................................................72
Oil pressure warning lamp................................72
Rear fog lamp indicator......................................73
Seat belt reminder...............................................73
Stability control (ESP) indicator.....................73
Start-stop indicator.............................................73
Warning Triangle............................................177
Washer Fluid Check...................................200
Washers
See: Wipers and Washers.................................43
Washing
See: Cleaning the Exterior..............................204
Waveband button........................................235
Wheels and Tyres........................................208
General Information.........................................208
Technical Specifications..................................218
Windows and Mirrors....................................63
Windscreen Washers....................................44
Windscreen Wipers.......................................43
Automatic wiper system...................................43
Intermittent wipe.................................................43
Winter Tyres
See: Using Winter Tyres....................................217
Wipers and Washers.....................................43
303
304
(CG3568en)
">