- No category
advertisement
THOR WASHER/DRYER
INSTALLATION GUIDE
MODEL: WD-9900
Unpacking the Machine
1. Unpack the machine. Properly dispose of all packing
materials.
Summary
The Thor Combination Washer/
Dryer must be unpacked prior to installation. All packaging should be removed from the machine. Two water supply hoses with brass pressure reducers, a drain hose Ubracket, a wrench, and three plastic inserts will be located in a bag inside the drum.
!
VERY IMPORTANT
The shipping bolts located in the back of the machine must be removed prior to operating the machine.
2. Open the door to the drum and remove the bag containing
parts.
3. Check for two (2) water supply hoses with two (2) brass pressure reducers on the red end, one (1) drain hose bracket, one (1) wrench, and three (3)
plastic insert caps.
!
Locations
of Shipping Bolts
4. Unscrew the three shipping bolts on the back of the machine using the wrench
provided or a 13 mm socket.
5. Once the bolts are unscrewed fully they can be removed from
the machine.
6. Cover the holes left by the bolts with the plastic inserts located
in the bag of parts.
NOTE - ONCE SHIPPING BOLTS ARE REMOVED RUBBER SPACERS MAY FALL
DOWN AND OUT THROUGH BOTTOM OF MACHINE. THIS IS NORMAL AND WILL
NOT CAUSE ANY HARM OR MALFUNCTION.
Connecting Water Supply and Drain
1. The brass pressure reducer must be removed from both hoses before they can be attached to the machine.
Summary
The machine should be located within easy reach of the water supply, the drain pipe, and an electrical outlet The water supply should be connected once the machine is in the correct location, followed by the drain hose. Drain hose should be secure. All hoses and connections should be checked thoroughly before leaving machine unattended.
!
IMPORTANT
For ease of installation only one (1) pressure reducer needs to be used.
Both should be used under VERY
high pressure situations.
COLD HOT
2. When hoses are attached to the machine care must be taken to not strip the inlet valves.
3. Normally only one pressure reducer is needed. For above normal pressure both reducers may be necessary. For very low pressure situations you may leave both off.
With Adaptor
4. Attach both inlet hoses to the machine. The red end MUST be attached to the machine, as
it has metric threading.
5. Attach both hoses to the water supply. Be sure that the correct hose is on the correct inlet valve. (Hot-Hot; Cold-Cold)
Tighten all connections to prevent leaks, but do not over tighten.
4-6”
5. The U-bracket must be attached to the hose to hold it in the drain. It is recommended that
4-6 inches of hose should be left to go into the pipe.
5. Put the drain hose into the drain pipe, securing it to make sure that it cannot slip and flood.
Leveling the Machine and Finishing Up
1. Put the machine into its final operating location.
Summary:
The QuietLine washer/dryer should be installed on a level surface that is well supported to prevent vibration.
Preferably the machine should be installed on a solid and level floor surface.
The machine must be leveled properly before operation. This will prevent excessive noise, vibration, and possible damage to machine.
The QuietLine has four leveling legs which can be adjusted and locked for proper leveling.
2. Using a level, check both front to back and side to side on the machine. If it is not level, make appropriate adjustments to the feet until it is.
2. To adjust feet, loosen locknuts using the leveling leg wrench, and screw the foot up or down until the machine does not rock and is level.
REFER TO MACHINE’S MANUAL AND EZ WASH GUIDE FOR
OPERATING INSTRUCTIONS.
4. Hand tighten the locknuts against the base of the machine.
5. Using the leveling leg wrench, firmly secure the locknuts to prevent the legs from slipping.
6. Once the machine is level plug into electrical outlet.
6. Turn it on/off using the button located in the center of the panel.
FOR TECHNICAL SERVICE, HELP, OR
QUESTIONS ABOUT INSTALLING OR
INITIAL OPERATION OF YOUR THOR
COMBINATION WASHER/DRYER PLEASE
CALL
888-876-8002
www.OasisAppliance.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement