Preparing the remote control for
use
Installing the remote control
batteries
The remote control can operate your TV/DVD and
control the basic functions of connected audio/
video devices if you connect a REGZA-LINK®
compatible audio receiver or playback device
(ræ Page 47).
24
1 Remove the battery cover from the back of the
remote control.
Squeeze tab
and lift cover
2 Install two AAA size batteries. Match the + and
— symbols on the batteries to the symbols on
the battery compartment.
3 Close the battery cover on the remote control
until the tab snaps.
Caution: Batteries must not be exposed to
excessive heat such as sunshine, fire or the
like.
Note:
* Be sure to use AAA size batteries.
* Dispose of batteries in a designated
disposal area.
* Batteries should always be disposed of with
the environment in mind. Always dispose of
batteries in accordance with applicable laws
and regulations.
* |f the remote control does not operate
correctly, or if the operating range becomes
reduced, replace batteries with new ones.
» When necessary to replace batteries in the
remote control, always replace both
batteries with new ones. Never mix battery
types or use new and used batteries in
combination.
« Always remove batteries from the remote
control if they are dead or if the remote
control is not to be used for an extended
period of time. This will prevent battery acid
from leaking into the battery compartment.
Learning about the remote control
The buttons used for operating the TV/DVD are
described here. For the REGZA-LINK® remote
control functions, see the section “Using REGZA-
LINK?” (z& Page 47).
a <LI TTY
POWER
EJECT TV/DVD SLEEP
J
SLOW ANGLE MARKER SLOW 27
>
26 28
31 — 14.108 MENU | SEIU N REPEAT AB 29
32 30
33 34
TOSHIBA
Note: The error message “NOT AVAILABLE”
may appear if you press a key for a function
that is not available.
Dana N
~
11
12
13
14
15
16
17
18
19
20
21
22
POWER turns the TV on and off. When the
TV is on, the Power LED indicator on the TV
front will be illuminated in green.
SLEEP accesses the sleep timer (t# Page
47).
EJECT ejects the disc from the disc slot.
TVIDVD switches to TV or DVD mode.
Channel Numbers directly tune channels.
JUMP selects or locates a specific point with
the disc playback (ts Page 59); tunes to a
digital sub-channel as a “dash”.
DISPLAY displays setting or playback
information (xs Page 49, 63).
AUDIO SELECT selects the DVD
soundtrack language or VCD audio channel
(es Page 63).
VOL + — adjusts the volume level.
CH AY cycles through programmed
channels when no menu is on- screen (=
Page 34).
SUBTITLE selects the subtitle language or
switches subtitle off (5° Page 63).
INPUT/ZOOM selects the video input source
(rs Page 33); zooms into the center of the
image during disc playback (t= Page 59).
PLAY MODE sets the disc playback repeat
mode (1= Page 60).
MUTE reduces or turns off the sound (t#
Page 40).
DVD MENU accesses the DVD menu (5°
Page 62).
ENTER activates highlighted items in the
main menu system.
Arrow buttons (4 VY < b ) select or
adjust programming menus when a menu 1s
on-screen.
EXIT/CANCEL closes on-screen menus.
MENU/SETUP accesses the main TV menu
system (13 Page 27); configures the disc
playback settings (es Page 70).
PLAY begins playback of the loaded disc (1==
Page 36).
PAUSE suspends disc playback temporarily
or plays back disc frame by frame (t=# Page
56, 57).
STOP stops playback of the loaded disc (1=>
Page 56).
25
26
a I=" Tm,
EJECT TV/DVD SLEEP TOWER
3 A 1
4 2
5
7 6
10 SUBTITLE
11 / 8
Zoom | 9
12 44
PLAY MODE ba
15
16
17
18
( y 22
MET croi — 23
SLOW ANGLE MARKER SLOW 27
26 28
31 — 4 JOPMENU 29
32 E FIC SIZE 30
33 34
TOSHIBA
J
23
24
25
26
27
28
29
30
31
32
33
34
CLOSED CAPTION/SKIP »»i accesses
the Closed Caption menu (85° Page 39); skips
forward to locate later DVD chapters (55
Page 58).
CH RTN/SKIP =< returns to the last
viewed channel or source (15° Page 35); skips
back to beginning of current DVD chapter or
locate previous chapters (5° Page 58).
FF »> fast-forwards playback of the disc
(es Page 57).
REV << fast-reverses playback of the disc
( Page 57).
SLOW «i slow-reverses playback of the disc
(e= Page 57).
SLOW I» slow-forwards playback of the
disc (z& Page 57).
MARKER bookmarks specific points in the
playback range for later access (ts Page 60).
ANGLE changes the scene angle when
playing back a DVD recorded with multi-
angle scenes (t# Page 62).
REPEAT A-B repeats playback of a specific
section between two set points (r& Page 61).
TOP MENU accesses the top menu of DVDs
that contain two or more titles (5° Page 62).
RETURN returns to the root directory in
Audio CD playback (= Page 66); returns to
previous directory from Media Player sub-
folder or sub-menu (1& Page 53).
GAME displays the Game mode screen when
using the TV as display device for video
game consoles (= Page 51).
PIC SIZE cycles through the picture sizes
(te Page 35).
REGZA-LINK® Player Control menu
functions
1 From the Preferences menu, press A or Y
to select REGZA-LINK Player Control and
then press gm).
2 Press A or W to select the item you want to
control and then press =).
Power Turns the selected device on and
off.
Root Menu Accesses the top menu of the
selected device.
Accesses the contents list when you
Contents press =. At this time, the
Menu REGZA-LINK Player Control
menu will disappear.
Setup Menu Accesses the setup menu of a DVD
player.
Top Menu Accesses the top menu of a DVD
during playback.
Menu Accesses the menu of a DVD
during playback.
Note:
+ These functions depend on the devices that
are connected.
* The REGZA-LINK Player Control item will
be grayed out in the following conditions:
- A non-HDMI input is currently selected.
- The Enable REGZA-LINK item is set to
Off.
- The connected CEC device is not a
playback or recording device.
'REGZA-LINK® input source
selection
If a REGZA-LINK® device with HDMI switching
capability (e.g. Audio Receiver) is connected to
the HDMI input, you can select another REGZA-
LINK® device that is connected to the master
HDMI device using = 250 on the remote control or
the TV control panel = Page 33).
48
VOLUME and MUTE controls of
Audio Receiver
With your TV’s remote control, you can adjust or
mute the sound volume of the Audio Receiver.
* (4) E adjust the volume level.
* "O turns off the sound.
Note:
+ To use this function:
- Set Speaker Preference to Audio
Receiver in the REGZA-LINK Setup
menu.
- Confirm that a connected REGZA-LINK®
device (such as DVD player, etc.) is
selected for the Audio Receiver input
source.
* You can also use this function when the
audio receiver is connected to the TV's
DIGITAL AUDIO OUT terminal (not HDMI
connection). In this case, select a digital
audio input mode on the Audio Receiver.
* These functions depend on the device
connected.
Other REGZA-LINK® functions
When the Enable REGZA-LINK and each item
in the REGZA-LINK Setup menu are set to On,
the following functions will be enabled.
If a connected HDMI device
TV Auto Input starts playing video or audio, the
Switch TV will automatically switch to
the appropriate HDMI input.
TV Auto If a device is turned on, the TV
Power On turns on automatically.
If the TV is turned off, the TV
will send a message to turn off all
of the devices connected to the
TV.
From this item, you can set your
audio output preference to the
TV speakers or the audio
receiver speakers. When this
item is set to Audio Receiver,
the TV remote can be used to
adjust or mute the volume of the
audio receiver. This item will be
grayed out unless a REGZA-
LINK® compatible audio
receiver is connected.
Device Auto
Standby
Speaker
Preference
Note: When you turn on the audio receiver,
change its input source, or adjust the sound
volume, the sound will be output from the
audio receiver's speakers even if TV
Speakers has been selected. Turn the TV off
and on again to output the sound from the TV
Speakers.
To set the REGZA-LINK® Setup:
1 From the Setup menu, press À or W to
select REGZA-LINK Setup and then press
2 Press A or W to select Enable REGZA-
LINK and then press € or pp to select On.
Note: If you select Enable REGZA-LINK
Off, the other items will be grayed out.
3 Press A or W to select the REGZA-LINK
Setup item you want to use and then press <
or »- to select On or desired mode.
* TV Auto Input Switch: On/Off
* TV Auto Power: On/Off
* Device Auto Standby: On/Off
* Speaker Preference: TV Speakers/Audio
Receiver
4 To save the new settings, highlight Done and
then press 63.
To revert to the factory defaults, highlight
Reset and then press ¢w).
Displaying TV status information
To display TV status information using
DISPLAY:
DISPLAY
=~
Press "5" on the remote control.
The following information will display (if
applicable):
* Current input (ANT/CABLE, Video, etc.)
* If ANT/CABLE is the current input, either
“CABLE” (for cable TV) or “ANT” (for over-
the-air broadcasts).
* Channel number (if in ANT/CABLE mode)
* Channel label (if set)
* Digital signal strength indicator (bar graph in
lower right corner of box; for ATSC signal only)
* Stereo, Mono or SAP audio status (When HDMI
input mode, Dolby Digital or PCM)
* Video resolution
* Aspect ratio of incoming video signal (4:3 or
16:9) |
* V-Chip rating status
* GameTimer (if set)
To display more TV information:
DISPLAY
—
Press “>” on the remote control again.
The following additional information will display
for off air digital channels (if applicable):
* Title
* Duration
* Detailed description
Note: The location of the banner can be
moved to the top or bottom of the screen by
pressing A or Y while the DISPLAY is on-
screen.
Understanding the auto power off
feature
The TV will automatically turn itself off after
approximately 15 minutes if it is tuned to a vacant
channel or a station that completes its broadcast
for the day. This feature functions in ANT/
CABLE mode only.
Understanding the last mode
memory feature
If the power is cut off while you are viewing the
TV, the Last Mode Memory feature
automatically turns on the TV when the power
is resupplied.
Note: If it’s possible, and you will be away
from the TV for an extended period of time,
you should unplug the power cord.
49
">
