Avaya Aura Session Manager, Communication Manager, Cisco Unified Communications Manager, 2410, 7900 Series, 9600 Series, 96x1 Series, G430, IP Communicator, Aura Application Notes

Avaya Solution & Interoperability Test Lab

Configuring SIP trunks between Avaya Aura® Session

Manager Release 6.2, Avaya Aura® Communication

Manager Release 5.2.1 and Cisco Unified Communications

Manager Release 8.6.2 – Issue 1.0

Abstract

These Application Notes describe a sample configuration of a network that provides SIP trunks between Avaya Aura® Session Manager Release 6.2, Avaya Aura® Communication Manager

Element Server Release 5.2.1 and Cisco Unified Communications Manager Release 8.6.2.

Avaya Aura®

Session Manager provides SIP proxy/routing functionality, routing SIP sessions across a TCP/IP network with centralized routing policies and registrations for

SIP endpoints.

Avaya Aura® Communication Manager serves as an Element Server within the Avaya

Aura® architecture and supports H.323 and Digital.

Cisco Unified Communications Manager provides SIP trunks for connecting to other telephony systems and supports SCCP and SIP endpoints.

These Application Notes provide information for the setup, configuration, and verification of the call flows tested for this solution.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

1 of 44

SM62CM521CUCM86

1. Introduction

These Application Notes describe a sample configuration of a network that provides SIP trunks between Avaya Aura® Session Manager Release 6.2, Avaya Aura® Communication Manager

Release 5.2.1 and Cisco Unified Communications Manager (CUCM) Release 8.6.2.

This document focuses on the configuration of the SIP trunks and call routing. Detailed administration of other aspects of Communication Manager, Session Manager or Cisco Unified

Communications Manager will not be described. See the appropriate documentation listed in

Section 10 for more information.

2. Interoperability Testing

Avaya Aura® Communication Manager serves as an Element Server within the Avaya Aura® architecture and supports Avaya 9600 Series and 96x1 Series H.323 and 2410 Digital endpoints.

Testing was limited to station to station calls and supplemental features. Voice messaging was not tested. Interoperability was verified for SIP trunks between Avaya Aura® Session Manager

Release 6.2, Avaya Aura® Communication Manager Release 5.2.1 and Cisco Unified

Communications Manager Release 8.6.2.

2.1. Test Description and Coverage

Interoperability testing included making bi-directional calls between several different types of stations on both telephony systems with various features including hold, transfer, conference and forwarding.

An adaptation for the SIP entity was created to mitigate implementation deltas between the solutions tested.

2.2. Test Results and Observations

Overall test results were excellent. There were some minor issues in media behavior that were corrected by checking the Media Termination Point (MTP) box in CUCM SIP Trunk configuration. With media shuffling disabled, these tests passed.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

2 of 44

SM62CM521CUCM86

3. Reference Configuration

A SIP trunk is used to connect Avaya Aura® Session Manager and Cisco Unified

Communications Manager (CUCM), which routes calls between them based on the dialed number. In addition, a SIP trunk is configured between the Avaya Aura® Communication

Manager and the Avaya Aura® Session Manager. Cisco 7965, 7962 and 7941 were configured as SIP endpoints. Cisco 7965, 7942, 7961 and Cisco IP Communicator were configured as

SCCP endpoints. Cisco SIP and SCCP endpoints were registered to Cisco Unified

Communications Manager.

As shown in Figure 1, CUCM 8.6.2 supports Cisco 7900 Series SCCP and SIP IP telephones.

CUCM is connected over a SIP trunk to Avaya Aura® Session Manager Release 6.2, using the

SIP Signaling network interface on Session Manager.

Figure 1

– Connection of Cisco Unified Communications Manager and Avaya

Aura® Communication Manager via Avaya Aura® Session Manager using SIP

Trunks

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

3 of 44

SM62CM521CUCM86

4. Equipment and Software Validated

The following equipment and software were used for the sample configuration.

Equipment/Software Release/Version

Avaya Aura® Session Manager on HP® DL

360 G7 Server

6.2.1.0.621010

Avaya Aura® System Manager on Dell® R610

Server

Avaya Aura® Communication Manager on

Avaya S8500 Server

Avaya G430 Media Gateway

Avaya 9640 H.323 Telephone

6.2.12.1871

5.2.1 SP 1201 (R015x.02.1.016.4)

Avaya 9621G H.323 Telephone

Avaya 2410 Digital Telephone

Avaya one-X Communicator

Cisco Unified Communications Manager

Cisco 7965 Unified IP Telephone

Cisco 7965 Unified IP Telephone

Cisco 7942 Unified IP Telephone

Cisco 7962 Unified IP Telephone

Cisco 7941 Unified IP Telephone

Cisco 7961 Unified IP Telephone

Cisco IP Communicator

30.22.0

3.0.04

H.323 6.0.2.0

(S9621_41HALBR6_2r039H_V4r52.tar)

N/A

6.1.3.08 SP3 patch2

8.6.2.21900-5 (8.6(2)SU1)

SIP45.9-2-3S

SCCP45.9-2-3S

SCCP42.9-2-3S

SIP42.9-2-3S

SIP41.9-2-3S

SCCP41.9-2-3S

8.6.1.0

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

4 of 44

SM62CM521CUCM86

5. Configure Avaya Aura® Communication Manager

This section describes the steps needed to configure Communication Manager to route and receive calls over the SIP trunk to Session Manager to support calls between Communication

Manager and Cisco Unified Communications Manager. These instructions assume the Avaya

G430 Media Gateway is already configured for Communication Manager. For more information describing these additional administration steps, see References [6] through [8] in Section 10.

This section describes the administration of Communication Manager using a System Access

Terminal (SAT). Some administration screens have been abbreviated for clarity.

The following administration steps will be described:

Verify System Capabilities and Communication Manager License

Configure Trunk-to-Trunk Transfers

Configure IP Codec Set

Configure IP Network Region

Configure IP Node Names and IP Addresses

Configure SIP Signaling Groups and Trunk Groups

Configure Route Pattern

Administer Private Numbering Plan and Uniform Dialplan

Administer Dialplan

Administer AAR Analysis

After completing these steps, the save translation command should be performed.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

5 of 44

SM62CM521CUCM86

5.1. Verify System Capacities and Licensing

This section describes the procedures to verify the correct system capacities and licensing have been configured. If there is insufficient capacity or if a required feature is not available, contact an authorized Avaya sales representative to make the appropriate changes.

Step 1: Verify SIP Trunk Capacity is sufficient for the expected number of calls.

On Page 2 of the display system-parameters customer-options command, verify an adequate number of SIP Trunk Members are administered for the system as shown below.

display system-parameters customer-options Page 2 of 11

OPTIONAL FEATURES

IP PORT CAPACITIES USED

Maximum Administered H.323 Trunks: 100 0

Maximum Concurrently Registered IP Stations: 18000 3

Maximum Administered Remote Office Trunks: 0 0

…

Maximum Video Capable IP Softphones: 0 0

Maximum Administered SIP Trunks: 100 20

…

Step 2: Verify AAR/ARS Routing features are Enabled on system.

To simplify the dialing plan for calls between telephony systems, verify the following AAR/ARS features are enabled on the system.

On Page 3 of the display system-parameters customer-options command, verify the following features are enabled.

ARS? Verify “y” is displayed.

ARS/AAR Partitioning? Verify “y” is displayed.

ARS/AAR Dialing without FAC? Verify “y” is displayed.

display system-parameters customer-options Page 3 of 10

OPTIONAL FEATURES

A/D Grp/Sys List Dialing Start at 01? n CAS Main? y

Answer Supervision by Call Classifier? n Change COR by FAC? n

ARS? y Computer Telephony Adjunct Links? n

ARS/AAR Partitioning? y

Cvg Of Calls Redirected Off-net? y

ARS/AAR Dialing without FAC? y DCS (Basic)? n

ASAI Link Core Capabilities? y DCS Call Coverage? n

…

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

6 of 44

SM62CM521CUCM86

Step 3: Verify Private Networking feature is Enabled.

On Page 5 of the display system-parameters customer-options command, verify the Private

Networking feature is set to “y”.

display system-parameters customer-options Page 5 of 10

OPTIONAL FEATURES

Uniform Dialing Plan? y

Private Networking? y

Usage Allocation Enhancements? y

Processor and System MSP? y

Processor Ethernet? y Wideband Switching? y

…

5.2. Configure Trunk-to-Trunk Transfers

Use the change system-parameters features command to enable trunk-to-trunk transfers. This feature is needed when an incoming call to a SIP station is transferred to another SIP station. For simplicity, the Trunk-to-Trunk Transfer field on Page 1 was set to “all” to enable all trunk-totrunk transfers on a system wide basis.

Note: Enabling this feature poses significant security risk by increasing the risk of toll fraud, and must be used with caution. To minimize the risk, a COS could be defined to allow trunk-to-trunk transfers for specific trunk group(s). For more information regarding how to configure

Communication Manager to minimize toll fraud, see Reference [8] in Section 10.

change system-parameters features Page 1 of 18

FEATURE-RELATED SYSTEM PARAMETERS

Self Station Display Enabled? n

Trunk-to-Trunk Transfer: all

Automatic Callback with Called Party Queuing? n

Automatic Callback - No Answer Timeout Interval (rings): 3

…

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

7 of 44

SM62CM521CUCM86

5.3. Configure IP Codec Set

Use the change ip-codec-set n command where n is the number used to identify the codec set.

Enter the following values:

Audio Codec:

Enter “G.711MU” and “G.729” as supported types.

Silence Suppression:

Retain the default value “n”.

Frames Per Pkt: Enter “2”.

Packet Size (ms): Enter “20”.

Media Encryption: Enter the value based on the system requirement.

For the sample configuration, “none” was used.

change ip-codec-set 1 Page 1 of 2

IP Codec Set

Codec Set: 1

Audio Silence Frames Packet

Codec Suppression Per Pkt Size(ms)

1: G.711MU n 2 20

2 :

G.729 n 2 20

3:

Media Encryption

1:

none

5.4. Configure IP Network Region

Use the change ip-network-region n command where n is an available network region.

Enter the following values and use default values for remaining fields.

Authoritative Domain: Enter the correct SIP domain for the configuration.

For the sample configuration, “avaya.com” was used.

Name:

Enter descriptive name.

Codec Set:

Enter the number of the IP codec set configured in

Section 5.3.

Intra-region IP-IP Direct Audio: Enter “yes”.

Inter-region IP-IP Direct Audio: Enter “yes”.

change ip-network-region 1 Page 1 of 19

IP NETWORK REGION

Region: 1

Location: Authoritative Domain: avaya.com

Name: Main Network Region

MEDIA PARAMETERS Intra-region IP-IP Direct Audio: yes

Codec Set: 1 Inter-region IP-IP Direct Audio: yes

UDP Port Min: 2048 IP Audio Hairpinning? n

UDP Port Max: 3329

…

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

8 of 44

SM62CM521CUCM86

5.5. Configure IP Node Names and IP Addresses

Use the change node-names ip command to add the node-name and IP Addresses for the

“procr” interface on Communication Manager and the SIP signaling interface of Session

Manager, if not previously added.

In the sample configuration, the node-name of the SIP signaling interface for Session Manager is

“asm1-r62” with an IP address of “10.80.65.76”.

change node-names ip Page 1 of 2

IP NODE NAMES

Name IP Address

asm1-r62 10.80.65.76

default 0.0.0.0

procr 10.80.65.78

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

9 of 44

SM62CM521CUCM86

5.6. Configure SIP Signaling Groups and Trunk Groups

This section provides the configuration of SIP trunk between Communication Manager and

Session Manager to support sending and receiving calls to/from stations supported by CUCM.

In the sample configuration, trunk group “10” and signaling group “10” were used for connecting to Session Manager.

Step 1: Add Signaling Group for SIP Trunk

Use the add signaling-group n command, where n is an available signaling group number.

Enter the following values and use default values for remaining fields.

Group Type: Enter “sip”.

IMS Enabled: Enter “n”.

Transport Method: Enter “tcp”.

Near-end Node Name: Enter “procr” node name from Section 5.5.

Far-end Node Name: Enter node name for the first Session Manager defined in Section 5.5.

Near-end Listen Port: Verify “5060” is used.

Far-end Listen Port:

Verify “5060” is used.

Far-end Network Region: Enter network region defined in Section 5.4.

Far-end Domain:

Enter domain name for Authoritative Domain

DTMF over IP: field defined in Section 5.4.

Verify “rtp-payload” is used. add signaling-group 10 Page 1 of 2

SIGNALING GROUP

Group Number: 10 Group Type: sip

IMS Enabled? n Transport Method: tcp

Q-SIP? n

IP Video? n Priority Video? n Enforce SIPS URI for SRTP? n

Near-end Node Name: procr

Far-end Node Name: asm1-r62

Near-end Listen Port: 5060 Far-end Listen Port: 5060

Far-end Network Region: 1

Far-end Domain: avaya.com

Bypass If IP Threshold Exceeded? n

Incoming Dialog Loopbacks: eliminate RFC 3389 Comfort Noise? n

DTMF over IP: rtp-payload Direct IP-IP Audio Connections? y

Session Establishment Timer(min): 3

IP Audio Hairpinning? n

Enable Layer 3 Test? y Direct IP-IP Early Media? n

H.323 Station Outgoing Direct Media? n Alternate Route Timer(sec):

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

10 of 44

SM62CM521CUCM86

Step 2: Add SIP Trunk Group

Add the corresponding trunk group controlled by the signaling group defined in Step 1 using the

add trunk-group n command where n is an available trunk group number.

Enter the following values and use default values for remaining fields.

Group Type:

Enter “sip”.

Group Name:

Enter a descriptive name.

TAC: Enter an available trunk access code.

Direction: Enter “two-way”.

Outgoing Display?

Enter “n”.

Service Type:

Enter “tie”.

Signaling Group:

Enter the number of the signaling group added in Step 1.

Number of Members: Enter the number of members in the SIP trunk (must be within the limits for number of SIP trunks configured in Section 5.1).

Note: once the add trunk-group command is completed, trunk members will be automatically generated based on the value in the Number of Members field.

add trunk-group 10 Page 1 of 21

TRUNK GROUP

Group Number: 10 Group Type: sip CDR Reports: y

Group Name: trk to asm1-r62 COR: 1 TN: 1

TAC: #10

Direction: two-way Outgoing Display? n

Dial Access? n Night Service:

Queue Length: 0

Service Type: tie Auth Code? n

Member Assignment Method: auto

Signaling Group: 10

Number of Members: 20

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

11 of 44

SM62CM521CUCM86

On Page 3, enter the following values and use default values for remaining fields.

Numbering Format

Enter “private”.

Show ANSWERED BY on Display

Enter “y”.

add trunk-group 10 Page 3 of 21

TRUNK FEATURES

ACA Assignment? n Measured: none

Maintenance Tests? y

Numbering Format: private

UUI Treatment: service-provider

Replace Restricted Numbers? n

Replace Unavailable Numbers? n

Show ANSWERED BY on Display? y

On Page 4, enter the following values and use default values for remaining fields.

Support Request History

Enter “y”.

Telephone Event Payload Type

Enter “101”.

add trunk-group 10 Page 4 of 21

PROTOCOL VARIATIONS

Mark Users as Phone? y

Prepend '+' to Calling Number? n

Send Transferring Party Information? n

Network Call Redirection? n

Send Diversion Header? n

Support Request History? y

Telephone Event Payload Type: 101

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

12 of 44

SM62CM521CUCM86

5.7. Configure Route Pattern

This section provides the configuration of the route pattern used in the sample configuration for routing calls to stations supported by Cisco Unified Communications Manager.

Use change route-pattern n command where n is an available route pattern.

Enter the following values and use default values for remaining fields.

Grp No Enter a row for the trunk group defined in Section 5.6.

FRL Enter “0”.

Numbering Format

Enter “lev0-pvt”.

In the sample configuration, route pattern “10” was created as shown below.

change route-pattern 10 Page 1 of 3

Pattern Number: 10 Pattern Name: sip trk to asm1

SCCAN? n Secure SIP? n

Grp FRL NPA Pfx Hop Toll No. Inserted DCS/ IXC

No Mrk Lmt List Del Digits QSIG

Dgts Intw

1: 10 0

n user

2: n user

3: n user

…

BCC VALUE TSC CA-TSC ITC BCIE Service/Feature PARM No. Numbering LAR

0 1 2 M 4 W Request Dgts Format

Subaddress

1: y y y y y n n rest lev0-pvt none

2: y y y y y n n rest none

3: y y y y y n n rest none

…

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

13 of 44

SM62CM521CUCM86

5.8. Administer Private Numbering Plan

Extension numbers used for SIP Users registered to Session Manager or for stations supported by

Cisco Unified Communications Manager must be added to either the private or public numbering table on Communication Manager. For the sample configuration, private numbering was used and all extension numbers were unique within the private network. However, in many customer networks, it may not be possible to define unique extension numbers for all users within the private network. For these types of networks, additional administration may be required as described in Reference [7] in Section 10.

Use the change private-numbering n command, where n is the length of the private number.

Fill in the indicated fields as shown below.

Ext Len:

Enter length of extension numbers.

In the sample configuration, “4” was used.

Ext Code: Enter leading digit (s) from extension number.

In the sample configuration, “40” was used for SIP

stations on Communication Manager and “30” was used for

stations supported by Cisco Unified Communications Manager.

Trk Grp(s): Enter trunk group defined in Section 5.6.

Private Prefix:

Leave blank unless an enterprise canonical numbering scheme is defined in Session Manager. If so, enter the appropriate prefix.

Total Length: Enter “4”.

change private-numbering 1 Page 1 of 2

NUMBERING - PRIVATE FORMAT

Ext Ext Trk Private Total

Len Code Grp(s) Prefix Len

4 30 10 4

Total Administered: 3

4 40 10 4

Maximum Entries: 540

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

14 of 44

SM62CM521CUCM86

5.9. Administer Uniform Dialplan

This section provides the configuration of the Uniform Dialplan pattern used in the sample configuration for routing calls between the telephony systems.

Note: Other methods of routing may be used.

Use the change uniform-dialplan n command where n is the first digit of the number assigned to a station supported by Cisco Unified Communications Manager. In the sample configuration, the numbers on the CUCM system start with digits “30”.

Fill in the indicated fields as shown below and use default values for remaining fields.

Matching Pattern Enter the number Communication Manager matches to dialed

numbers. Accepts up to seven digits.

Len

Enter the number of user-dialed digits the system collects to

match to this Matching Pattern value.

Del

Enter number of digits to delete before routing the call.

Net

The server or switch network used to analyze the converted number. The converted digit-string is routed either as an

extension number or through its converted AAR address, its

converted ARS address, or its ENP node number.

In the sample configuration “aar” was used.

Conv

Enables or disables additional digit conversion.

change uniform-dialplan 1 Page 1 of 2

UNIFORM DIAL PLAN TABLE

Percent Full: 0

Matching Insert Node

Pattern Len Del Digits Net Conv Num

30 4 0 aar n

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

15 of 44

SM62CM521CUCM86

5.10. Administer Dial Plan

Use the change dialplan analysis command.

In the sample configuration, 4-digit extension numbers starting with “30” are used for stations supported by Cisco Unified Communications Manager.

Fill in the indicated fields as shown below and use default values for remaining fields.

Dialed String Enter digit pattern for extension numbers on CUCM system.

Total Length Enter length of extension numbers.

For the sample configuration, “4” was used.

Call Type

Enter “ext”.

change dialplan analysis 1 Page 1 of 12

DIAL PLAN ANALYSIS TABLE

Location: all Percent Full: 1

Dialed Total Call Dialed Total Call Dialed Total Call

String Length Type String Length Type String Length Type

30 4 ext

40 4 ext

* 3 fac

# 3 dac

5.11. Administer AAR Analysis

Use the change aar analysis n command.

In the sample configuration, 4-digit extension numbers starting with “30” are used for stations supported by Cisco Unified Communications Manager.

Fill in the indicated fields as shown below and use default values for remaining fields.

Dialed String Enter digit pattern for extension numbers on CUCM system.

Total Min Enter minimum length of extension numbers.

For the sample configuration, “4” was used.

Total Max

Enter maximum length of extension numbers.

For the sample configuration, “4” was used.

Call Type

Enter “unku”.

change aar analysis 1 Page 1 of 2

AAR DIGIT

ANALYSIS TABLE

Location: all Percent Full: 1

Dialed Total Route Call Node ANI

String Min Max Pattern Type Num Reqd

30 4 4 10 unku n

40 4 4 10 unku n

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

16 of 44

SM62CM521CUCM86

5.12. Save Translations

Configuration of Communication Manager Element Server is complete. Use the save

translation command to save these changes.

Note: After making a change on Communication Manager which alters the dial plan or numbering plan, synchronization between Communication Manager and System Manager must be completed and SIP telephones must be re-registered.

See Section 6.8 for more information on how to perform an on-demand synchronization.

6. Configure Avaya Aura® Session Manager

This section describes the procedures for configuring Avaya Aura® Session Manager to route calls between Communication Manager and CUCM.

These instructions assume other administration activities have already been completed such as defining SIP entities for Session Manager, defining the network connection between System

Manager and Session Manager and defining SIP users. For more information on these additional actions, see References [3] and [5] in Section 10.

The following administration activities will be described:

Define SIP Domain

Configure Adaptation Module for calls to Cisco Unified Communications Manager.

Define SIP Entities for both telephony systems.

Define Entity Links, which describe the SIP trunk parameters used by Session Manager when routing calls between SIP Entities.

Define Routing Policies and Dial Patterns which control routing between SIP Entities.

Synchronize Changes with Avaya Aura® Communication Manager.

Note: Some administration screens have been abbreviated for clarity.

Configuration is accomplished by accessing the browser-based GUI of Avaya Aura® System

Manager, using the URL “http://<ip-address>/SMGR”, where “<ip-address>” is the IP address of Avaya Aura® System Manager. Log in with the appropriate credentials.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

17 of 44

SM62CM521CUCM86

6.1. Define SIP Domains

Expand Elements  Routing and select Domains from the left navigation menu.

Click New (not shown). Enter the following values and use default values for remaining fields.

Name

Enter the Authoritative Domain Name specified in Section 5.4.

For the sample configuration, “avaya.com” was used.

Type

Select “sip” from drop-down menu.

Notes

Add a brief description. [Optional].

Click Commit to save. The screen below shows the SIP Domain defined for the sample configuration.

Repeat to create a domain for CUCM called “cucm.com”.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

18 of 44

SM62CM521CUCM86

6.2. Configure Adaptations

Session Manager can be configured to use Adaptation Modules to modify SIP messages before or after routing decisions are made. For example, Adaption Modules are used to support interoperability with third party SIP products such as Cisco Unified Communications Manager.

Expand Elements  Routing and select Adaptations from the left navigational menu.

Click New (not shown). In the

General

section, enter the following values and use default values for remaining fields.

Adaptation Name: Enter an identifier for the Adaptation Module.

Module Name: Select “CiscoAdapter” from drop-down menu.

Module parameter: Enter “iosrcd=<domain>” where <domain> is the domain defined in Section 6.1.

Enter “odstd=<IP address>” where <IP address> is address for Cisco Unified Communications Manager system.

Note: iosrcd is the abbreviation for Ingress Override Source

Domain parameter and odstd is the abbreviation for Override

Destination Domain parameter. For more information on use of module parameters, see Reference [5] in Section 10.

Notes:

Enter a brief description. [Optional]

Click Commit. The Adaptation Module defined for sample configuration is shown below.

Note: Digit conversion was not required for sample configuration.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

19 of 44

SM62CM521CUCM86

6.3. Define SIP Entities

A SIP Entity must be added for each telephony system connected over a SIP trunk to Session

Manager.

Expand Elements  Routing and select SIP Entities from the left navigation menu.

Click New (not shown). In the

General

section, enter the following values and use default values for remaining fields to define a SIP Entity for CUCM system.

Name:

Enter an identifier for new SIP Entity.

FQDN or IP Address: Enter IP address of CUCM system.

Type:

Select “SIP Trunk”.

Adaptation:

Select the Adaptation Module configured for CUCM

in Section.6.2

Notes:

Enter a brief description. [Optional].

In the

SIP Link Monitoring

section:

SIP Link Monitoring: Select “Link Monitoring Enabled”.

Click Commit to save SIP Entity definition. The following screen shows the SIP Entity defined for the Cisco Unified Communications Manager system.

Repeat this step to define a SIP Entity for Communication Manager.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

20 of 44

SM62CM521CUCM86

6.4. Define Entity Links

A SIP trunk between Session Manager and each telephony system is described by an Entity Link.

To add an Entity Link, expand Elements  Routing and select Entity Links from the left navigation menu.

Click New (not shown). Enter the following values.

Name Enter an identifier for the link to CUCM system.

SIP Entity 1 Select SIP Entity defined for Session Manager.

See Reference [5] in Section 10 for more information.

SIP Entity 2 Select the SIP Entity defined in Section 6.3 for CUCM system.

Protocol After selecting both SIP Entities, select “TCP” as the required

Protocol.

Port

Verify Port for both SIP entities is “5060”.

Trusted

Enter .

Notes

Enter a brief description. [Optional].

Click Commit to save Entity Link definition.

The following screen shows the Entity Link defined between Session Manager and Cisco

Unified Communications Manager.

Repeat this step to define an Entity Link between Session Manager and Communication

Manager using the same port number as specified in Section 5.6 Step 1.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

21 of 44

SM62CM521CUCM86

6.5. Define Routing Policy

Routing policies describe the conditions under which calls will be routed to the SIP Entities specified in Section 6.4. Two routing policies must be added, one for Cisco Unified

Communications Manager and a second policy for Communication Manager Element Server.

To add a routing policy, expand Elements  Routing and select Routing Policies.

Click New (not shown). In the

General

section, enter the following values.

Name:

Enter an identifier for policy being added for CUCM system.

Disabled:

Leave unchecked.

Notes:

Enter a brief description. [Optional].

In the

SIP Entity as Destination

section, click Select. The SIP Entity List page opens (not shown).

Select the SIP Entity defined for CUCM system in Section 6.3 and click Select.

The selected SIP Entity displays on the Routing Policy Details page.

Use default values for remaining fields. Click Commit to save Routing Policy definition.

Note: the routing policy defined in this section is an example and was used in the sample configuration. Other routing policies may be appropriate for different customer networks.

The following screen shows the Routing Policy defined in the sample configuration for routing calls to CUCM system.

Repeat this step to define a Routing Policy for routing calls to Communication Manager.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

22 of 44

SM62CM521CUCM86

6.6. Define Dial Pattern

Define dial patterns to direct calls to the appropriate telephony system. In the sample configuration, 4-digit extensions beginning with “30” reside on Cisco Unified Communications

Manager and 4-digit extensions beginning with “40” reside on Avaya Aura® Communication

Manager.

To define a dial pattern, expand Elements  Routing and select Dial Patterns.

Click New (not shown). In the

General

section, enter the following values and use default values for remaining fields.

Pattern: Enter dial pattern associated with CUCM system.

Min: Enter the minimum number digits that must to be dialed.

Max: Enter the maximum number digits that may be dialed.

SIP Domain: Select the SIP Domain from drop-down menu or select “ALL” if

Session Manager should accept incoming calls from all SIP domains.

Notes:

Enter a brief description. [Optional].

In the

Originating Locations and Routing Policies

section, click Add.

The Originating Locations and Routing Policy List page opens (not shown).

In Originating Locations table, select “ALL” .

In Routing Policies table, select the appropriate Routing Policy defined for CUCM system in Section 6.5.

Click Select to save these changes and return to Dial Patterns Details page.

Click Commit to save the new definition.

The following screen shows the Dial Pattern defined for routing calls to Cisco Unified

Communications Manager.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

23 of 44

SM62CM521CUCM86

Repeat this step to define the Dial Pattern for routing calls to Communication Manager.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

24 of 44

SM62CM521CUCM86

6.7. Synchronize Changes with Avaya Aura® Communication

Manager

If changes are made on Communication Manager which alters the dial plan or numbering plan, perform on-demand synchronization to synchronize the data between System Manager and

Communication Manager.

Expand Elements  Inventory  Synchronization and select Communication System.

On the Synchronize CM Data and Configure Options page, expand the

Synchronize CM

Data/Launch Element Cut Through table and select the row associated with Communication

Manager Element Server as shown below.

Click to select Incremental Sync data for selected devices option. Click Now (not shown) to start the synchronization.

Use the Refresh button in the table header to verify status of the synchronization.

Verify synchronization successfully completes by verifying the status in the Sync. Status column is “Completed”.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

25 of 44

SM62CM521CUCM86

7. Configure Cisco Unified Communications Manager

This section describes the relevant configuration of the SIP Trunk and call routing between Cisco

Unified Communications Manager and Session Manager.

The following administration activities will be described:

Verify Audio Codec Configuration

Configure Media Termination Point

Configure SIP Trunk Security Profile

Configure SIP Trunk Security Profile

Define Avaya SIP Profile

Configure SIP Trunk to Session Manager

Define Routing Pattern

These instructions assume the basic configuration of the Cisco Unified Communications

Manager system has already been completed and the system is configured to support the SCCP

(IP) and SIP telephones and associated Media Resources. For more information on how to administer these other aspects of Cisco Unified Communications Manager, see Reference [18] in Section 10.

Note: Some administration screens have been abbreviated for clarity.

Cisco Unified Communications Manager is configured using the Cisco Unified CM

Administration web administration GUI.

Access the GUI using the URL “http://<IP Address>:8443/ccmadmin/showHome.do” where

“<ip-address>” is the IP address of Cisco Unified Communications Manager.

Select the “Cisco Unified CM Administration” application from the Navigation drop-down menu.

Click Go and login with the appropriate credentials as shown below.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

26 of 44

SM62CM521CUCM86

7.1. Verify Audio Codec Configuration

The Audio Codec settings defined for CUCM system should match the set of Audio Codecs defined for Communication Manager in Section 5.3.

Expand System menu and select Region. Click Find (not shown) and select Default region.

Verify “64 kbps (G.722, G.711)” is displayed in the Max Audio Bit Rate field as shown below.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

27 of 44

SM62CM521CUCM86

7.2. Configure Media Termination Point

Media Termination Points extend supplementary services, such as hold, transfer, call park, and conferencing that are otherwise not available when a call is routed to a SIP endpoint.

Expand Media Resources (not shown) and select Media Termination Point. Click Find to list available Media Termination Points. Verify at least one media termination points has been defined and verify the following fields:

Device Pool

Status

Verify “Default” is selected.

Verify “Registered with <IP Address>” is displayed where

“<IP Address>” is the IP address of the CUCM system.

IP address Verify IP address of Cisco Unified Communications

Manager system.

In the sample configuration, the IP address of the Cisco Unified Communications Manager system is “10.80.65.103” and the default media termination point is “MTP_2” as shown below.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

28 of 44

SM62CM521CUCM86

7.3. Configure Avaya SIP Trunk Security Profile

Expand System  Security (not shown) and select SIP Trunk Security Profile. Click

to configure a SIP Trunk Security Profile.

Enter the following values and use defaults for remaining fields:

Name

Description

Enter name.

Enter a brief description.

Device Security Mode Verify “Non Secure” is selected.

Incoming Transport Type Verify “TCP+UDP” is selected.

Outgoing Transport Type Verify “TCP” is selected.

Accept Out-of-Dialog REFER Enter .

Accept Unsolicited Notification

Enter .

Accept Replaces Header Enter .

Click . The screen below shows the SIP Trunk Security Profile for the sample configuration.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

29 of 44

SM62CM521CUCM86

7.4. Define Avaya SIP Profile

Expand Device  Device Settings and select SIP Profile. Click .

Under SIP Profile Information section, enter the following values and use defaults for remaining fields:

Name

Description

Enter name.

Enter a brief description.

Default MTP Telephony Event Payload Type

Enter “101”.

Disable Early Media on 180

Enter .

Click . The screen below shows SIP Profile for the sample configuration.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

30 of 44

SM62CM521CUCM86

7.5. Define SIP Trunk to Avaya Aura® Session Manager

Expand Device select Trunk (not shown) Click

Manager.

to define a SIP Trunk to Session

Under Trunk Information section, enter the following values as shown below and click Next.

Truck Type

Device Protocol

Trunk Service Type

Select “SIP Trunk”.

Defaults to “SIP”.

Defaults to “None”.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

31 of 44

SM62CM521CUCM86

Under Device Information section, enter the following values and use defaults for remaining fields as shown below:

Device Name

Description

Enter name.

Enter a brief description.

Device Pool Select “Default”.

Media Resource Group List Select previously defined Media Resource

Group List. See References [18] thru [20]

in Section 10 for more information.

Media Termination Point Required

Enter .

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

32 of 44

SM62CM521CUCM86

Scroll to SIP Information section, enter the following values and use defaults for remaining fields:

Destination Address

Enter IP address of SIP signaling interface for

Session Manager.

Destination Port Defaults to “5060”.

MTP Preferred Originating Codec Select “711ulaw”.

SIP Trunk Security Profile Select SIP Trunk Security Profile defined in Section 7.3.

SIP Profile Select SIP Profile defined in Section 7.4.

DTMF Signaling Method Select “RFC 2833”.

Click Save. The screen below shows SIP Information defined for SIP Trunk to Session Manager for the sample configuration.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

33 of 44

SM62CM521CUCM86

7.6. Define Routing Pattern

Expand Call Routing  Route/Hunt select Route Pattern (not shown).

Click to configure new Route Pattern. Enter the following values as shown below and use defaults for remaining fields.

Route Pattern

Enter dialed digits for calls routed to Session Manager.

For sample configuration, “40XX” was used.

Description

Gateway/Route List

Enter brief description [Optional].

Select name of SIP trunk defined in Section 7.5.

Provide Outside Dial Tone Enter .

Click . The screen below shows Route Pattern defined for the sample configuration to route calls to Session Manager.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

34 of 44

SM62CM521CUCM86

8. Verification Steps

8.1. Verify Avaya Aura® Session Manager Configuration

Step 1: Verify Avaya Aura® Session Manager is Operational

Expand Elements  Session Manager and select Dashboard to verify the overall system status of Session Manager.

In the sample configuration, “asm62” was the name of the SIP Entity defined for the Session

Manager used for testing with Cisco Unified Communications Manager.

Verify the correct status of the following fields is displayed as shown below.

Tests Pass

Security Module

Service State

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

35 of 44

SM62CM521CUCM86

Step 2: Verify SIP Entity Link Status

Navigate to Elements  Session Manager  System Status  SIP Entity Monitoring to view more detailed status information for the specific SIP Entity Links used for calls between

Communication Manager and Cisco Unified Communications Manager.

Select the SIP Entity for Cisco Unified Communications Manager from the All Monitored SIP

Entities table (not shown) to open the SIP Entity, Entity Link Connection Status page.

Verify the Conn. Status is “Up” as shown below:

Click Show to view more information associated with the Entity Link.

Repeat this step to verify the status of the Entity Link to Communication Manager.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

36 of 44

SM62CM521CUCM86

8.2. Verify Avaya Aura® Communication Manager Operational Status

Step 1: Verify status of SIP trunk between Communication Manager and Session Manager.

Verify the status of the SIP trunk group by using the status trunk n command, where n is the trunk group number administered in Section 5.6.

Verify that all trunks in the trunk group are in the “in-service/idle” state as shown below:

status trunk 10

TRUNK GROUP STATUS

Member Port Service State Mtce Connected Ports

Busy

0010/001 T00001 in-service/idle no

0010/002 T00002 in-service/idle no

0010/003 T00003 in-service/idle no

0010/004 T00004 in-service/idle no

0010/005 T00005 in-service/idle no

0010/006 T00006 in-service/idle no

0010/007 T00007 in-service/idle no

0010/008 T00008 in-service/idle no

0010/009 T00009 in-service/idle no

0010/010 T00010 in-service/idle no

Verify the status of the SIP signaling group by using the status signaling-group command, where n is the signaling group number administered in Section 5.6.

Verify the status of the Group State field is “in-service” shown below:

status signaling-group 10

STATUS SIGNALING GROUP

Group ID: 10

Group Type: sip

Group State: in-service

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

37 of 44

SM62CM521CUCM86

Step 2: Verify calls to stations supported by CUCM system are correctly routed over the SIP trunk to Session Manager.

Use the SAT command, list trace tac #, where tac # is the trunk access code for the SIP trunk group defined in Section 5.6 to trace trunk group activity. For example, the trace below illustrates a call from an h.323 endpoint using “4002” on Communication Manager” to a SCCP station on Cisco Unified Communications Manager using “3002”.

list trace tac #10 Page 1

LIST TRACE time data

18:41:36 Calling party station 4002 cid 0x835

18:41:36 Calling Number & Name 4002 4002, user

18:41:36 dial 3002 route:UDP|AAR

18:41:36 term trunk-group 10 cid 0x835

18:41:36 dial 3002 route:UDP|AAR

18:41:36 route-pattern 10 preference 1 location 1/ALL cid 0x835

18:41:36 seize trunk-group 10 member 3 cid 0x835

18:41:36 Calling Number & Name NO-CPNumber NO-CPName

18:41:36 SIP>INVITE sip:[email protected];user=phone SIP/2.0

18:41:36 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:36 Setup digits 3002

18:41:36 Calling Number & Name 4002 4002, user

18:41:36 SIP<SIP/2.0 100 Trying

18:41:36 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:36 Proceed trunk-group 10 member 3 cid 0x835

18:41:36 SIP<SIP/2.0 180 Ringing

18:41:36 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:36 Alert trunk-group 10 member 3 cid 0x835

18:41:41 SIP<SIP/2.0 200 OK

18:41:41 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:41 SIP>ACK sip:[email protected]:5060;transport=tcp SIP/2.0

18:41:41 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:41 active trunk-group 10 member 3 cid 0x835

18:41:41 G711MU ss:off ps:20

rgn:1 [10.80.65.103]:26026

rgn:1 [10.80.65.79]:2052

18:41:41 xoip options: fax:T38 modem:off tty:US uid:0x50003

xoip ip: [10.80.65.79]:2052

18:41:41 SIP>INVITE sip:[email protected]:5060;transport=tcp SIP/2.0

18:41:41 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:41 SIP<SIP/2.0 100 Trying

18:41:41 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:41 SIP<SIP/2.0 200 OK

18:41:41 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:41 G711MU ss:off ps:20

rgn:1 [10.80.64.50]:2920

rgn:1 [10.80.65.103]:26030

18:41:41 SIP>ACK sip:[email protected]:5060;transport=tcp SIP/2.0

18:41:41 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:41 G711MU ss:off ps:20

rgn:1 [10.80.65.103]:26030

rgn:1 [10.80.64.50]:2920

18:41:43 SIP>BYE sip:[email protected]:5060;transport=tcp SIP/2.0

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

38 of 44

SM62CM521CUCM86

18:41:43 Call-ID: 0f0b4b11ad8e11f19d4feecfa00

18:41:43 idle station 4002 cid 0x835

rgn:1 [192.45.130.100]:28544

rgn:1 [10.80.111.170]:2054

8.3. Verify Cisco Unified Communications Manager Operational

Status

Step 1: Verify the operational status of the Cisco Unified Communications Manager system.

From the Cisco Unified CM Administration Home Page described in Section 7, select the “Cisco

Unified Serviceability” application (not shown) to verify status of the Cisco system.

Expand Tools (not shown) and select Control Center – Feature Services.

Under Select Server section, select the IP address of the Cisco Unified Communications

Manager system and click Go to view status of the system.

In the sample configuration, the IP address for the CUCM system is displayed as shown below.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

39 of 44

SM62CM521CUCM86

Under CM Services section, verify the status of the Cisco CallManager and Cisco IP Voice

Media Streaming App services as shown below. Verify the following fields:

Status

Verify “Started” is displayed.

Activation Status

Verify “Activated” is displayed.

Step 2: Use the Real Time Monitoring Tool (RTMT) to monitor events on CUCM system.

This tool can be downloaded by expanding Application  Plugins from the Cisco Unified CM

Administration web interface. For further information, see Reference [18] in Section 10.

Start the tool. Expand Tools on left panel and select Trace & Log Central. Under Trace and

Log Central section, select Real Time Trace to start a real time data capture as shown below.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

40 of 44

SM62CM521CUCM86

8.4. Call Scenarios Verified

Verification scenarios for the configuration described in these Application Notes included the following call scenarios:

Station to Station Calls:

Using G.711 audio codec, verify displays and talk path for calls between different types of stations on Avaya Aura® Communication Manager and stations on Cisco Unified

Communications Manager.

Using G.729 audio codec, verify displays and talk path for calls between different types of stations on Avaya Aura® Communication Manager and stations on Cisco Unified

Communications Manager.

Verify a second call can be made between different types of stations on Avaya Aura®

Communication Manager and stations on Cisco Unified Communications Manager after the first call is abandoned.

Supplemental Calling Features:

Verify calls from different types of stations on Avaya Aura®

Communication Manager to a station on Cisco Unified Communications Manager can be placed on hold.

Verify calls from different types of stations on Avaya Aura® Communication Manager to a station on Cisco Unified Communications Manager can be transferred to another station on the same switch or back across the SIP trunk to a station on the remote switch.

Verify calls from different types of stations on Avaya Aura®

Communication Manager to a station on Cisco Unified Communications Manager can create a conference with another station on either the same switch or remote switch.

Verify calls from different types of stations on Avaya Aura®

Communication Manager to a station on Cisco Unified Communications Manager can be forwarded to another station on the same switch or back across the SIP trunk to a station on the remote switch.

Repeat the hold, transfer, conference and forward scenarios with calls originating from a station on Cisco Unified Communications Manager.

9. Conclusion

These Application Notes describe how to configure a network that provides SIP trunks between

Avaya Aura® Session Manager Release 6.2, Cisco Unified Communications Manager Release

8.6.2 and Avaya Aura® Communication Manager Release 5.2.1. Avaya Aura® Communication

Manager serves as a Element Server within the Avaya Aura® architecture and supports Avaya

9600 Series and 96x1 Series IP Deskphones (H.323) and 2410 Digital Telephones are supported by Avaya Aura® Communication Manager.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

41 of 44

SM62CM521CUCM86

10. Additional References

Avaya Product documentation relevant to these Application Notes is available at

Avaya Aura® Session Manager

1)

Avaya Aura® Session Manager Overview, Doc ID 03-603323.

2) Installing and Configuring Avaya Aura® Session Manager, Doc ID 03-603473.

http://support.avaya.com

.

3) Avaya Aura® Session Manager Case Studies, Doc ID 03-603478.

4) Maintaining and Troubleshooting Avaya Aura® Session Manager, Doc ID 03-603325.

5) Administering Avaya Aura® Session Manager, Doc ID 03-603324.

Avaya Aura® Communication Manager

6) Administering Avaya Aura® Communication Manager, Doc ID 03-300509.

7) Avaya Aura® Communication Manager Screen Reference, Doc ID 03-602878.

8) Avaya Toll Fraud and Security Handbook, Doc ID 555-025-600.

Avaya 9600 Series and 9601 Series IP Deskphones

9) Avaya one-X® Deskphone SIP Administrator Guide. December 6, 2010.

10) Avaya one-X® Deskphone SIP for 9600 Series IP Telephones Administrator Guide,

Release 2.6.

11) Avaya one-X® Deskphone SIP Installation and Maintenance Guide Release 6.2 for 9601

IP Deskphone.

12) Avaya one-X® Deskphone SIP Installation and Maintenance Guide Release 6.0 for 9608,

9611G, 9621G and 9641G IP Deskphones.

13) Avaya one-X® Deskphone SIP Installation and Maintenance Guide Release 2.6.

Avaya Application Notes

14) Configuring SIP trunks among Avaya Aura® Session Manager Release 6.1, Avaya

Aura® Communication Manager Release 6.0.1 and Cisco Unified Communications

Manager Release 8.0.3

15) Configuring SIP trunks among Avaya Aura® Session Manager Release 6.1, Avaya

Aura® Communication Manager Release 6.0.1 and Cisco Unified Communications

Manager Release 8.0.3.

16) Configuring SIP Trunks between Avaya Aura® Session Manager Release 6.2, Avaya

Aura® Communication Manager Release 6.2 and Cisco Unified Communications

Manager Release 8.6.2 – Issue 1.0

17) Integrating Avaya Aura® Session Manager Release 6.2, Avaya Modular Messaging

Release 5.2 and Cisco Unified Communications Manager Release 8.6.2 – Issue 1.0

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

42 of 44

SM62CM521CUCM86

Cisco Unified Communications Manager

Cisco Product documentation relevant to these Application Notes is available at http://www.cisco.com

.

18) Cisco Unified Communications Manager Administration Guide, Release 8.6(1), Part

Number: OL-24919-01.

19) Cisco Unified Communications Manager Features and Services Guide, Part Number:

OL-24921-01.

20) Cisco Unified Real-Time Monitoring Tool Administration Guide, Part Number: OL-

24544-01.

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

43 of 44

SM62CM521CUCM86

©

2012 Avaya Inc. All Rights Reserved.

Avaya and the Avaya Logo are trademarks of Avaya Inc. All trademarks identified by ® and

™ are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners. The information provided in these Application

Notes is subject to change without notice. The configurations, technical data, and recommendations provided in these Application Notes are believed to be accurate and dependable, but are presented without express or implied warranty. Users are responsible for their application of any products specified in these Application Notes.

Please e-mail any questions or comments pertaining to these Application Notes along with the full title name and filename, located in the lower right corner, directly to the Avaya Solution &

Interoperability Test Lab at [email protected]

Reviewed: ML

SPOC 9/18/2012

Solution & Interoperability Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

44 of 44

SM62CM521CUCM86