James Hardie 667404 HardieTrim HZ5 1 in. x 3.5 in. x 144 in. Fiber Cement Smooth ColorPlus Trim Board manual

PDF

Dokument

Reklama

HardieTrim

®

Boards Products Description

HardieTrim ® boards come finished with either the PrimePlus ® factory primer and sealer or with ColorPlus ® Technology.

The ColorPlus ® coating is a factory-applied, oven-baked finish available on a variety of James Hardie ® siding and trim products. See your local dealer for details and availability of products, colors, and accessories.

HARDIETRIM ® 5/4, 4/4 BOARDS

HardieTrim ® 5/4, 4/4 board is a decorative non-load bearing trim product. HardieTrim 5/4 board is 1-in. thick,

HardieTrim 4/4 board is 3/4 in. thick, and both can be purchased in 10-ft. and 12-ft. lengths, based on local availability.

In addition to frieze, rake, window, door, and corner details, HardieTrim 5/4, 4/4 boards may be used to construct light blocks, column wraps and decorative scroll work. Available in commonly-used nominal widths from 4 in. to 12 in.

HARDIETRIM ® BATTEN BOARDS

HardieTrim ® Batten Boards are a decorative non-load bearing trim product. HardieTrim ® Batten Boards are ¾ in. thick, 2½ in. wide, and come on 12’ lengths. See your local dealer for details and availability of product colors and accessories.

HardieTrim 5/4, 4/4 board - Smooth HardieTrim Batten board -

Rustic and Smooth (not shown)

HardiePanel vertical siding with

HardieTrim Batten board for the

Board & Batten look.

! WARNING

DO NOT caulk nail heads when using ColorPlus products.

Refer to the ColorPlus touch-up section

A Complete James Hardie Exterior –

Close-up on trim products.

ColorPlus TIP: HardieTrim 5/4, 4/4 boards with

ColorPlus Technology is shipped with a protective laminate slip sheet. James Hardie recommends keeping the protective sheet in place during cutting and fastening to reduce damage to the boards. Remove the protective sheet only after installing the boards and filling the nail holes with a colored touch-up pen.

Installation of HardieTrim ® 5/4, 4/4 & NT3 ® Back Grooved Boards

Appendix/ Glossary

Cutting and Fastening

ESR-1844 & 2290 Report

CONCEALED FASTENING TABS

For Corners, Band Boards, Windows, and Door Applications: HardieTrim ® boards can be installed with Flat Tabs

(JH sku no. 280154) and Corner Tabs (JH sku no. 280155) which provide concealed fastening. Only Flat and Corner

Tabs can be used with HardieTrim ® boards to create a concealed fastening. Additional framing may be required to ensure the Flat and Corner Tabs are fastened properly to the structure. Special attention should be paid to the framing when using a sheathing that does not have fastener holding equivalent to OSB or Plywood sheathing.

Step 1: Attach Flat Tabs to the back side of the trim with 4 18 ga. ½ in. L x ¼ in. W narrow crown corrosion resistant staples, equally spaced in one row, positioned no closer than ½ in. from trim edges, using a pneumatic staple gun. (Figure 8.1)

Step 2: For wood frame construction, attach the trim to the building using 2, 6d siding nails fastened through the Flat

Tabs. ET&F or equivalent fasteners may be used to attach the Flat Tabs to steel frame construction. (Figures 8.2)

Fastener spacing will vary based on application. Refer to specific sections in these instructions for required fastener spacing by application (window, band board, etc.). (Figures 8.13)

8.1

2 in. min.

1/2 in. min.

Fasten 4 staples to the center of the nailing ridge.

8.2

Fasten HardieTrim

Flat Tab to min. 7/16 in. OSB with min. 2, 6d siding nails

HardieTrim ™ Flat Tab

Installation of HardieTrim tabs in Coastal Regions:

James Hardie requires that stainless steel staples & fasteners be used when installing HardieTrim ™ Tabs in coastal regions.

Installation of HardieTrim Tabs over Pressure Treated Lumber:

HardieTrim ™ tabs shall not come in direct contact with ACQ or CA preservative-treated wood. Refer to the General Fastening section of this document for further information.

HardieTrim ® NT3 ™ boards with ColorPlus ® Technology:

Remove the laminate sheet as soon as possible after attaching the trim to the building.

TRIMMING CORNERS

HardieTrim ® boards are installed around corners by pre-building the corner off the wall with the Corner Tabs (JH sku no. 280155).

• Attach Corner Tabs to the back side of the trim with 8 18 ga. ½ in. L x ¼ in. W narrow crown corrosion resistant staples using a pneumatic staple gun. Ensure the Corner Tabs are fastened tight and straight to the trim boards. (Figures 8.3)

• For wood frame construction, attach the trim to the building with 2, 6d siding nails fastened through the Corner Tabs.

ET&F or equivalent fasteners may be used to attach the Corner Tabs to steel frame construction. (Figures 8.4)

• Attach a Corner Tab 1 in. from each edge and every 20 in. o.c.

• TIP: Creating a jig for the work station is recommended to ensure the corners are fastened securely and straight.

(Figures 8.6)

8.3

8.4

Corner studs

8.5

8.6

Corner Tabs

Fasten

2 in. x 4 in. timber blocks to a work bench

Use 4 staples per piece of trim to fasten the L-shaped tab to the pre-built corner. Use the nail line on the tabs as a guide. Siding Nail

Corner Tab

22.5º - 45º weather cut

HardieTrim

HardieTrim ™ Corner Tab

Fasten 2 in. x 8 in. stud to the timber blocks

TRIM APPLICATION FOR WINDOWS, DOORS & OTHER OPENINGS

Trim the opening prior to the installation of the siding (Figure 8.7). Place a Flat Tab at the end of each trim board and one tab every 16 in. OC. Attach the trim boards and Flat Tabs around the opening as shown in Figures 8.7 and 8.8.

8.7-A

Side trim pieces go to the top of the window.

8.7-B

Header piece spans the window including the side trim pieces.

Flashing needs to be tucked under the water resistive barrier and over the Flat Tabs.

Water-resistive barrier

Do not caulk between the siding and the flashing.

1/4 in. gap

8.8

Bottom trim piece is the width of the window.

NOTE: Follow your window/door manufacturers installation instructions.

1/8 in. caulked gap is left between siding and the side trim pieces.

BAND BOARD

Application

Framing Material

Tab is nailed into

Fastener

(tab to framing)

Fastener

(tab to Hardietrim)

Flat Tab

Wood Stud

(minimum G=0.42)

One 6d corrosion resistant siding nail installed through center of flange into framing

Minimum APA rated

7/16" OSB

Minimum 20 gauge steel

Wood Stud

(minimum G=0.42)

Corner Tab

Minimum APA rated

7/16" OSB

Minimum 20 gauge steel

Two 4d ring shank corrosion resistant siding nails equally spaced installed through flange into framing

One No. 8 X 1" long X 0.323" head diameter screw (corrosion resistant) installed through flange into framing

On each flange, Install one 6d corrosion resistant siding nail through flange into framing

On each flange, Install two 4d ring shank corrosion resistant siding nails through flange into framing

On each flange, Install one No. 8 X 1" long X 0.323" head diameter screw

(corrosion resistant) through flange into framing

Four 18 ga. X 1/2" long X 1/4" wide corrosion resistant crown staples, equally spaced in one row

For each piece of trim, install Four 18 ga. X 1/2" long X

1/4" wide corrosion resistant crown staples, equally space in two rows

A flashing is required over the trim and Flat Tabs. (Figure 8.9) Terminate ends of the Band Board into Trim or Siding or miter cut the edges of the trim at the corners of the building. Place a Flat Tab at the end of each trim board and one tab every stud at a maximum of 16 in. o.c. The Flat Tabs should be attached to the trim in an alternating pattern to the top and bottom of the band board (Figures 8.10 and 8.11).

Fasten 4 staples to the tab as shown

8.9

8.10

Flat Tabs

Water-resistive Barrier

Sheathing

HardiePlank ® Lap Siding

Blocking

1/4 in. gap. Do not caulk.

8.11

16 in. o.c. max

Flat Tabs

Flashing

16 in. o.c. max

8.12

FLUSH

Caulk

Flat and

Corner Tabs

Application

Framing Material

Tab is nailed into

Fastener

(tab to framing)

Siding nail attaches tab to the wall.

Do not under drive nails.

Only use staples to fasten

Flat and Corner Tabs to the trim boards.

Wood Stud

(minimum G=0.42)

One 6d corrosion resistant siding nail installed through center of flange into framing

Minimum APA rated

7/16" OSB

Four 18 ga. X 1/2"

Fastener

(tab to Hardietrim)

Max Tab Spacing

(inches on center)

16 45

Wood Stud

(minimum G=0.42)

One No. 8 X 1" long X 0.323" head diameter screw (corrosion resistant)

Minimum APA rated

7/16" OSB

Two 4d ring shank corrosion resistant siding nails equally spaced installed flange into framing

Minimum APA rated

7/16" OSB

On each flange, Install two 4d ring shank corrosion resistant siding nails installed through flange into framing

Application

Four 18 ga. X 1/2" long X 1/4" wide corrosion resistant crown staples, equally spaced in ga. X 1/2" long X

Framing Material

Tab is nailed into

Framing Material

Wood Stud

(minimum G=0.42)

Wood Stud

(minimum G=0.42)

Minimum APA rated

Minimum 20 gauge steel

Fastener

(tab to framing)

One 6d corrosion resistant siding nail

Fastener installed through center of flange into framing installed through center of flange into framing

One 6d corrosion resistant siding nail siding nails equally spaced installed through flange into framing

Two 4d ring shank corrosion resistant siding nails equally spaced installed

One No. 8 X 1" long X 0.323" head diameter screw (corrosion resistant) installed through flange into framing

Fastener Fastener

(tab to Hardietrim)

Four 18 ga. X 1/2"

Max Tab Spacing

(inches on center)

Max Tab Spacing

(inches on center)

Four 18 ga. X 1/2" long X 1/4" wide corrosion resistant crown staples, equally spaced in corrosion resistant crown staples,

Minimum 20 gauge steel

Minimum APA rated

7/16" OSB

Minimum 20 gauge steel

On each flange, Install one No. 8 X 1" long X 0.323" head diameter screw

On each flange, Install two 4d ring shank corrosion resistant siding nails through flange into framing

On each flange, Install one No. 8 X 1" long X 0.323" head diameter screw

(corrosion resistant) through flange into framing

For each piece of trim, install Four 18 ga. X 1/2" long X

1/4" wide corrosion resistant crown staples, equally space in two rows

Corner Tab

Minimum 20 gauge steel

Wood Stud

(minimum G=0.42)

One No. 8 X 1" long X 0.323" head diameter screw (corrosion resistant)

Wood Stud diameter screw (corrosion resistant)

(minimum G=0.42)

Minimum APA rated

7/16" OSB

Minimum APA rated

7/16" OSB

Minimum 20 gauge steel flange into framing corrosion resistant siding nail through

Minimum 20 gauge steel installed through flange into framing

On each flange, Install one 6d corrosion resistant siding nail through flange into framing

On each flange, Install one 6d

On each flange, Install two 4d ring shank corrosion resistant siding nails through flange into framing

On each flange, Install two 4d ring shank corrosion resistant siding nails long X 0.323" head diameter screw

For each piece of trim, install Four 18 ga. X 1/2" long X

1/4" wide corrosion resistant crown

1/4" wide corrosion

(corrosion resistant) through flange into framing long X 0.323" head diameter screw

(corrosion resistant) through flange into framing one row

For each piece of trim, install Four 18 shank corrosion resistant siding nails through flange into framing ga. X 1/2" long X

1/4" wide corrosion resistant crown staples, equally space in two rows resistant crown staples, equally

Appendix/ Glossary

ESR-1844 & 2290 Report

Installation of HardieTrim

5/4, 4/4 & NT3

Back Grooved Boards

FASTENER TABLE

8.13

Application

Framing Material

Tab is nailed into

Fastener

(tab to framing)

Fastener

(tab to Hardietrim)

Max Tab Spacing

(inches on center)

Cutting and Fastening

Flat Tab

Corner Tab

Wood Stud

(minimum G=0.42)

One 6d corrosion resistant siding nail installed through center of flange into framing

Minimum APA rated

7/16" OSB

Minimum 20 gauge steel

Wood Stud

(minimum G=0.42)

Minimum APA rated

7/16" OSB

Minimum 20 gauge steel

Two 4d ring shank corrosion resistant siding nails equally spaced installed through flange into framing

One No. 8 X 1" long X 0.323" head diameter screw (corrosion resistant) installed through flange into framing

On each flange, Install one 6d corrosion resistant siding nail through flange into framing

On each flange, Install two 4d ring shank corrosion resistant siding nails through flange into framing

On each flange, Install one No. 8 X 1" long X 0.323" head diameter screw

(corrosion resistant) through flange into framing

Four 18 ga. X 1/2" long X 1/4" wide corrosion resistant crown staples, equally spaced in one row

For each piece of trim, install Four 18 ga. X 1/2" long X

1/4" wide corrosion resistant crown staples, equally space in two rows

Wind-Borne Debris Region: “Supplemental fasteners may be necessary when installing tabs in a Wind-Borne Debris

Region, please call Technical Services 800-942-7343 with any questions.”

RECOGNITION: HardieTrim boards may be installed as an equal alternative to conventional trim permitted for use in; the 1997

Uniform Building Code, Section 601.5.5; the 1997 Standard Building Code, Section 1404.1; the 1999 BOCA National Building Code,

Section 1407.2.2; 2003 International Building Code, Section 1402.1, the 2003 International Residence Code for One - and Two -

Family - Dwellings, Section R703.1. the 2003 International Residence Code for One - and Two - Family - Dwellings, Section R703.1. and the 1998 International One-and -Two -Family Dwelling Code,Section 601.1.

OUTSIDE CORNERS

Corners made from HardieTrim ® 5/4, 4/4 boards can be pre-assembled before they’re installed. Pre-assembled corners look better and generally make the installation go more quickly. To join two pieces of HardieTrim 5/4, 4/4 boards for a corner, drive 2-in. 16 ga. corrosion-resistant finish nails 1 /

in. from the edge and spaced 16in. apart along the edge.

To fasten 4-in. corners to the wall, drive a pair of finish nails or siding nails, (one nail into each face of the corner) with the nails spaced 16 in. apart. For 6-in. corners, drive a pair of finish nails or siding nails into each face spaced 16 in. apart. Nails should be kept 3 /

in. from the edges of the board and

1-in. from the ends.

When walls are more than 10 ft. high, splice corner boards together using weather cuts of at least a 22.5° angle. The angle of the weather cut must slope downward and away from the building. Then nail both boards to the building with the same attachment schedule as for pre-assembled corners, except that 4-in. HardieTrim 5/4,

4/4 boards that should get two nails per side every 16 in. Only install trim by butting to it with the siding. Do not install any trim product over James Hardie ® siding.

8.14

Pre-built corner installation 4-in boards

A pair of nails (one in each face) attach the corner to the building.

Water-resistive barrier

16-in.

(max.)

Keep nails at least 1 in. from ends and 3 /

in. from edges.

Pre-built corner installation 6-in boards

Two nails in each face attach the corner to the building.

16-in.

(max.)

Keep nails at least 1 in. from ends and 3 /

in. from edges.

NOTE: All weather cut joints should be touched up prior to installation.

WARNING

Use only 2-in. 16-ga. finish nails to pre-assemble HardieTrim 5/4, 4/4 board corners.

INSIDE CORNERS

Inside corners can be made with either a single HardieTrim 5/4, 4/4 board in the corner, or with one board on each wall depending on the desired look.

8.17

Single board

8.15

Weather cuts

Keep weather cuts at least 12 in. apart on adjacent corner boards.

Angle slopes down and to the outside.

8.16

Join lengths of boards with angled cuts at least 22.5˚

TIP: When pre-assembling exterior corners using

HardieTrim 5/4, 4/4 boards, position the finish nailer parallel with the trim

Installation of HardieTrim

5/4, 4/4 & NT3

Back Grooved Boards

Cutting and Fastening

BAND BOARD

8.18

A Band board is a decorative horizontal trim used to break up the field of siding on a building. Any width of HardieTrim ®

5/4, 4/4 boards can be used for band Flashing

Water-resistive barrier laps over flashing.

Sheathed wall

Water-resistive barrier board depending on the type of detail desired. If installing a band board, pay special attention to flashing details and allow for potential shrinkage of solid rim

Starter strip joists in the walls that the band board may be attached to.

Do not caulk

1 /

-in. gap between the flashing and the siding.

Caulk between the underside of the band board and the siding below. Do not caulk between the flashing and sid-

Band board ing above the band board, and maintain a 1 /

-in. gap between the two. Also

Starter strip angles the siding above the band board.

Caulk joint below the band board.

make sure that the water-resistive barrier laps over the flashing for a continu-

Band board ous drainage plane. If running lap siding or shingle siding above the band board, a starter strip should be installed first to maintain the correct siding angle. Small Periodic gaps should be left in the starter strip to provide an escape route for excess moisture that may drain down behind the siding.

Use bevel-cut splice joints of at least 22.5° to join long lengths of HardieTrim 5/4, 4/4 boards. To attach band board to the building, drive two recommended fasteners every 16 in. for 4-in. and 6-in. boards. For 8-in. boards, use three fasteners every 16 in., and use four fasteners every 16 in. for 12-in. boards.

Appendix/ Glossary

ESR-1844 & 2290 Report

HARDIETRIM 5/4, 4/4 BOARDS FASTENER SPECIFICATIONS

The Fastener Specifications table shows fastener options for a variety of different nailing substrates. Please refer to the applicable ESR report online (see back page) to determine which fastener meets your wind load design criteria.

Fastening Substrate Approved Fastener wood studs 10

7

Fastening Types

Trim Screw, 2 in.

screw

Nailing Patterns

4-in over minimum

7/16 in. OSB steel studs

7 12

6-in

1 nail every 16 in. to attach boards together

1 nail every 16 in. for each board

1 nail every 16 in. to attach boards together

2 nails every 16 in. for each board

Pre-built corners

10

16 gauge, 2 in.

11

AST-075-0200G finish nail

ET&F finish nail

12

ET&F

[AKN100-0150NA] .100 in. x .25 in. x 1.5 in.

4-in &

6-in

2 nails every 16 in.

indicates recommended fasteners

8-in 3 nails every 16 in.

TIP: James Hardie recommends using stainless steel finish nails when installing HardieTrim (Trim, Battens, Fascia, etc.) products.

12-in 4 nails every 16 in.

WINDOW AND DOOR TRIM

Windows and doors must be installed per the manufacturer’s instructions. Window flanges or flashings must be properly installed and lapped correctly under the water-resistive barrier prior to the installation of HardieTrim ® 5/4, 4/4 boards. Once the

HardieTrim 5/4, 4/4 boards is put on, proper flashing must be installed above the trim and lapped under the water-resistive barrier correctly.

Install HardieTrim 5/4, 4/4 boards around doors and windows using the “cap over” method, which means that the header or horizontal top piece of the trim extends and caps over the vertical jamb pieces on both sides. For windows, the bottom trim piece or sill trim fits in between the jambs.

For cap-over trim installation:

1) Start by measuring the length of the bottom edge of the window, not including the flange.

2) Cut a piece of trim to that length and install it.

3) Next measure from the bottom of the installed trim to the top of the window.

4) Cut two pieces of trim to that length and install them on either side of the window.

5) For the cap, measure the distance between the outside edges of the side trim pieces. Cut a piece of trim to length and install it.

For doors the process is the same except that it starts with the side pieces, step three.

8.19

Window and door trim

Side trim pieces go to the top of the window.

Bottom trim piece is the width of the window.

8.21

Water-resistive barrier

Flashing

Starter strip

1 / 8 -in. caulked gap is left between siding and the side trim pieces.

8.20

Header piece spans the window including the side trim pieces.

Do not caulk between the siding and the flashing.

1 /

in. gap

8.22

Window flange

Shim

Window trim

TIP: For trimming around windows and doors with attachment flanges, install a shim strip to build out the wall even with the flange. This strip lets the trim sit flat and parallel with the wall.

Appendix/ Glossary

ESR-1844 & 2290 Report

Installation of HardieTrim

5/4, 4/4 & NT3

Back Grooved Boards

Cutting and Fastening

INSTALLING RAKE AND FASCIA BOARD

HardieTrim boards can be fastened directly over a 2x sub-fascia or directly to rather tails. Check local building code for relevant codes.

James Hardie recommends that the fascia be no more than 2 in. larger than the subfascia, e.g. over a nominal 2x6 subfascia, install an 8-in. fascia board (7 1 /

-in. actual) fascia. On longer fascia runs, join HardieTrim boards with weather/bevel cuts.

WARNING

Use only 2-in. 16-ga. finish nails to pre-assemble HardieTrim 5/4, 4/4 board corners.

8.23

Fascia

Subfascia

Rafter tails

Ledger

Sheathed wall

DRIP EDGE

After the fascia is installed, a vinyl, coated aluminum or galvanized drip-edge flashing must be installed to the roof sheathing overlapping the fascia board. The drip edge helps protect the top edge of the fascia board and it minimizes water ingress into the soffit and/or cornice cavity.

Choose a drip edge design that effectively channels water away from the face of the fascia and into gutters if present.

8.24

Drip edge

Rafter tail Roof sheathing

Fascia

Subfascia

Soffit

Ledger

Blocking

Sheathed wall

Installation of HardieTrim

Battens

GETTING STARTED

HardieTrim ® Battens are intended to be used with HardiePanel ® vertical siding to achieve a board and batten look.

HardieTrim Battens must be attached to wood or steel backing using an approved fastener from the table below. When installing HardieTrim Battens, determine layout and mark where battens will be attached. To ensure that HardieTrim

Battens are installed vertically and parallel to each other, either snap chalk lines or use a level. When attaching battens ensure that fasteners are a minimum of

3/4 in. from edges, 1 in. from ends, and a maximum of 16 in. o.c.

8.25

Snapped chalk line guides the installation

HardiePanel®

Siding

Water resistive barrier

HardieTrim®

Boards

HardieTrim®

Battens

ColorPlus

TIP:

HardieTrim ® Battens with

ColorPlus ® Technology are shipped with a protective laminate slip sheet. James Hardie recommends keeping the protective sheet in place during cutting and fastening to reduce damage to the boards.

Remove the protective sheet only after installing the boards and filling the nail holes with a colored touch-up pen. Finish nails are required for

ColorPlus products.

HARDIETRIM BATTENS FASTENING SPECIFICATIONS

Fastening Substrate wood studs

Approved Fastener

Fastener Types

Trim Screw, 2 in.

6d screw over minimum

7/16 in. OSB

16 gauge, 2 in.

finish nail steel studs 7 12 11

AST-075-0200G

ET&F finish nail

ET&F

[AKN100-0150NA] .100 in. x .25 in. x 1.5 in.

Indicates recommended fasteners. Required for ColorPlus ® Products.

TIP: James Hardie recommends using stainless steel finish nails when installing

HardieTrim (Trim, Battens, Fascia, etc.) products.

Installation of HardieTrim

Battens (continued)

Appendix/ Glossary

Cutting and Fastening

HORIZONTAL JOINT TREATMENT

Horizontal HardieTrim ® Batten joints must occur at the same location as horizontal joints in HardiePanel ® siding.

Install horizontal HardieTrim Batten joints by using one of the following options:

1) If HardieTrim Battens are going to be installed over horizontal panel joints without the use of a horizontal band board, follow the procedure as illustrated in fig. 8.26. Start installing

HardieTrim Battens by creating a weather-cut of at least a 22.5° angle, making a joint at the same location as the panel joint. Attach the bottom batten. Make sure the top batten has a matching weathercut and then install top batten.

2) If HardieTrim Battens are to be installed over horizontal panel joints with the use of a horizontal band board, follow the procedure as illustrated in fig. 8.27. If HardieTrim

Battens are to be installed horizontally, they must be installed in the same manner as in fig. 8.27.

Make sure the horizontal Z-flashing is installed over both the lower panel and the horizontal band board.

Attach the bottom batten tight to the bottom edge of the band board.

Next, leaving a minimum 1/4 in. gap above the horizontal Z-flashing, install the top batten.

8.26

1 No Horizontal Band-Board

Water-resistive barrier

Upper panel

HardieTrim

Batten

1 /

-in. Gap

1 No Horizontal Band-Board

22.5 - 45° weather cut

Water-resistive barrier

Water-resistive

Flashing

HardieTrim

Batten

1 /

-in. Gap

22.5 - 45° weather cut

Upper panel

Don’t caulk gap between flashing and upper panel.

Lower panel

2 Horizontal Band-Board

Flashing

Lower panel

Water-resistive barrier

Water-resistive barrier between flashing and upper panel.

Upper panel

Lower panel

HardieTrim

Batten

HardieTrim

Batten

Upper panel

HardieTrim

Batten

8.27

2 Horizontal Band-Board 1 /

4 -in. Gap

Water-resistive barrier

Flashing

Water-resistive

Decorative

Don’ t caulk gap between fl ashing and upper panel.

band board

Upper panel

HardieTrim

Board used as

Band-Board

HardieTrim

Batten

HardieTrim

Batten

1 /

4 -in. Gap

Flashing

Decorative band board

Don’ Lower panel gap between fl ashing and upper panel.

HardieTrim

Board used as

Band-Board

HardieTrim

Batten

HardieTrim

Batten Lower panel

ESR-1844 & 2290 Report

WARNING

Do not bridge floors with HardieTrim Battens and/or HardiePanel Siding.

A horizontal joint should always be created between floors.

INSTALLATION REQUIREMENTS - 4/4, 5/4, BATTENS, PRIMED & COLORPLUS ® PRODUCTS

EFFECTIVE MAY 2015

Visit www.jameshardie.com

for the most recent version.

IMPORTANT: FAILURE TO INSTALL AND FINISH THIS PRODUCT IN ACCORDANCE WITH APPLICABLE BUILDING CODES AND JAMES HARDIE WRITTEN

APPLICATION INSTRUCTIONS MAY LEAD TO PERSONAL INJURY, AFFECT SYSTEM PERFORMANCE, VIOLATE LOCAL BUILDING CODES, AND VOID THE

PRODUCT ONLY WARRANTY. BEFORE INSTALLATION, CONFIRM THAT YOU ARE USING THE CORRECT HARDIEZONE INSTRUCTIONS. INSTALLATION OF

HZ5 PRODUCTS OUTSIDE AN HZ5 LOCATION WILL VOID YOUR WARRANTY. TO DETERMINE WHICH HARDIEZONE APPLIES TO YOUR LOCATION,

VISIT WWW.HARDIEZONE.COM OR CALL 1-866-942-7343 (866 9HARDIE)

STORAGE & HANDLING: CUTTING INSTRUCTIONS

Store flat and keep dry and covered prior to installation. Installing James Hardie siding product wet or saturated may result in shrinkage at butt joints. Carry product on edge.

OUTDOORS

1. Position cutting station so that wind will blow dust away from user

and others in working area.

2. Use one of the following methods:

a. Better: i. Dust reducing circular saw equipped with a

HardieBlade ® saw blade and HEPA vacuum extraction

b. Good: i. Dust reducing circular saw with a HardieBlade saw blade

(only use for low to moderate cutting)

INDOORS

- NEVER use a power saw indoors

- NEVER use a circular saw blade that does not carry the HardieBlade

saw blade trademark

- NEVER dry sweep – Use wet suppression or HEPA Vacuum

Protect edges and corners from breakage.

James Hardie is not responsible for damage caused by improper storage and handling of the product.

NIOSH-approved respirators can be used in conjunction with above cutting practices to further reduce dust exposures. Additional exposure information is available at www.jameshardie.com to help you determine the most appropriate cutting method for your job requirements. If concern still exists about exposure levels or you do not comply with the above practices, you should always consult a qualified industrial hygienist or contact James Hardie for further information.

SD083105

HardieTrim

NT3

™

boards are decorative non-load bearing trim products.

Do not use HardieTrim NT3 boards to replace any structural component.

GENERAL REQUIREMENTS

• Wood or steel must be provided for attaching HardieTrim boards.

• Follow all applicable codes when installing HardieTrim boards.

• DO NOT install HardieTrim boards, such that they may remain in contact with standing water.

• DO NOT use stain, oil/alkyd base paint, or powder coating on James Hardie Products.

James Hardie products contain respirable crystalline silica, which is known to the State of California to cause cancer and is considered by IARC and NIOSH to be a cause of cancer from some occupational sources. Breathing excessive amounts of respirable silica dust can also cause a disabling and potentially fatal lung disease called silicosis, and has been linked with other diseases. Some studies suggest smoking may increase these risks. During installation or handling: (1) work in outdoor areas with ample ventilation; (2) use fiber cement shears for cutting or, where not feasible, use a HardieBlade saw blade and dust-reducing circular saw attached to a HEPA vacuum; (3) warn others in the immediate area; (4) wear a properly-fitted, NIOSH-approved dust mask or respirator (e.g. N-95) in accordance with applicable government regulations and manufacturer instructions to further limit respirable silica exposures. During clean-up, use HEPA vacuums or wet cleanup methods - never dry sweep. For further information, refer to our installation instructions and Material Safety Data Sheet available at www.jameshardie.com or by calling 1-800-9HARDIE (1-800-942-7343). FAILURE TO ADHERE TO OUR WARNINGS, MSDS, AND

INSTALLATION INSTRUCTIONS MAY LEAD TO SERIOUS PERSONAL INJURY OR DEATH.

SD050905

TR1510_P1/9 03/15 53

FLASHING/CLEARANCE REQUIREMENTS NO-COVER

HardieTrim may be installed with a minimum

1/4 in. clearance when installed vertically to grade, decks, paths, steps, and driveways

Maintain a minimum 2 in. horizontal clearance between James Hardie trim products and decks, paths, steps and driveways.

Figure 2 Figure 3 horizontal trim

6 in. min.

siding water resistive barrier flashing trim deck material

2 in. min.

joist flashing ledger vertical trim

1/4 in. min.

Maintain a 1/4 in. clearance between the bottom of James Hardie products and horizontal flashing. Do not caulk gap.

Figure 5 siding

Do not

Caulk

1/4 in. gap

Drip Edge

Figure 6

At the juncture of the roof and vertical surfaces, flashing and counter flashing shall be installed per the roofing manufacturer’s instructions. Provide a 2 in. clearance between the roofing and the bottom edge of the trim.

Figure 4 trim

2 in.

min.

flashing for fascia installation see page 6

Mortar/Masonry

Figure 7

L-Flashing

Z-Flashing flashing

Block Penetration

Figure 8

Z-Flashing

Valley/Shingle Extension

Figure 9

Extend shingles at least 1 in. out from the fascia when gutters are present

CLEARANCE REQUIREMENTS UNDER-COVER

Figure 10 Maintain a 1/4 in. clearance for

HardieTrim boards installed under cover.

Under cover is defined as:

• Not more than 10 feet below a roof overhang, and

• Not less than 4 inches horizontally from the edge of the roof overhang

4 in. min.

1/4 in. min. clearance

10 ft. max

TR1510_P2/9 03/15

FASTENING

General Fastening Requirements

Fasteners must be corrosion resistant, galvanized, or stainless steel.

Electro-galvanized are acceptable but may exhibit premature corrosion.

James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing

James Hardie products near the ocean, large bodies of water, or in very humid climates.

Manufacturers of ACQ and CA preservative-treated wood recommend spacer materials or other physical barriers to prevent direct contact of

ACQ or CA preservative-treated wood and aluminum products.

Fasteners used to attach HardieTrim Tabs to preservative-treated wood shall be of hot dipped zinc-coated galvanized steel or stainless steel and in accordance to 2009 IRC R317.3 or 2009 IBC 2304.9.5.”

Pneumatic Fastening

James Hardie products can be hand nailed or fastened with a pneumatic tool.

Pneumatic fastening is highly recommended. Set air pressure so that the fastener is driven snug with the surface of the trim. A flush mount attachment on the pneumatic tool is recommended. This will help control the depth the nail is driven. If setting the nail depth proves difficult, choose a setting that under drives the nail. (Drive under driven nails snug with a smooth faced hammer - Does not apply for installation to steel framing).

Flush Snug Flush

Figure A

Finish Nail

Figure B

Siding Nail do not over drive siding nails do not under drive nails

Face Nailing Requirements

Use 2 in. minimum 16 ga. finish nails to attach HardieTrim NT3 boards to wood frame construction. ET&F or equivalent fasteners or screws may be used to attach

HardieTrim NT3 boards to steel frame construction.

Fastening instructions are similar for all applications. When using finish nails, position nails no closer than 1/2 in. from the edges of the trim and for all other fasteners no closer than 3/4 in. Fasteners must be no closer than 1 in. from ends of trim and spaced a maximum of 16 in. O.C. Ensure trim is adequately fastened.

James Hardie recommends using stainless steel finish nails when installing HardieTrim products.

Minimum fastener guide for finish nailing:

Pre-built corner Site Built Corners

4 in.

6 in.

8 in.

12 in.

1 nail every 16 in. to attach boards together + 1 nail every 16 in. each board

1 nail every 16 in. to attach boards together + 2 nails every 16 in. each board

2 nails every 16 in.

3 nails every 16 in.

4 nails every 16 in.

Other areas (e.g. window trim, and band boards)

2 nails every 16 in.

3 nails every 16 in.

Use a 2 in. finish nail to fasten trim together. Longer finish nails may bend.

plywood or

OSB sheathing

1 in. from ends water-resistive barrier

16 in. O.C. maximum finish nailing pattern

*Follow all applicable codes when installing HardieTrim boards

Figure 11

Vertical trim may be installed with a 1/4 in. min. clearance*.

Leave a minimum 1/8 in. gap between the siding and trim, then caulk.

TR1510_P3/9 03/15

INSTALLATION

Trimming Corners

When installing corners or other vertical trim, position boards on the wall and attach (figure 12).

Pre-Built Corners

Alternatively, corners can be pre-built off the wall using 2 in. finishing nails. Each side of the pre-built corner must be secured to the wall (figure 13).

Figure 12

2 in. Finish nail corner studs

Trim application for windows, doors & other openings

Flashing over trim is required per code for all installation methods. (figure 14) flashing over trim do not caulk along top edge

HardieTrim board

Figure 14

Figure 13

2 in. Finish nail corner studs waterresistive barrier siding

Butt to Siding

Trim the opening prior to the installation of the siding.

Position trim boards on the wall and secure. Allow proper fastener spacing at edges and ends.

16 in. max.

Butt to Siding

Horizontal

Flashing

NOTE: Follow your window/door manufacturer’s installation instructions for caulking guidance between window and trim.

leave a minimum 1/8 in. gap between siding and trim, then caulk.

Frieze Boards

HardieTrim boards can be used as frieze board. (figure 16)

Band Board

For band board applications, a flashing is required over the trim. (figure 15) sheathing

Figure 15 blocking/support if required water resistive barrier lap siding

1/4 in. gap flashing

HardieTrim NT3 board

Figure 16

HardieTrim frieze board

HardieTrim frieze board caulk if required

HardiePlank lap siding Butt-to Siding

Shim behind trim

Trim Over Siding

TR1510_P4/9 03/15

INSTALLATION (cont.)

Batten Boards

Horizontal Panel Joints

At horizontal panel joints HardieTrim battens must be installed according to option 1 or 2 below.

When installing HardieTrim Battens horizontally, they must be installed as a panel joint according to option 2.

Option 1

Figure 17 - No horizontal band board - Make a 22.5- 45 degree weather cut, in the HardieTrim batten, just above the 1/4 in. clearance between panels.

Figure 17 HardieTrim

Batten upper panel

Do not

Caulk

1/4 in. gap

Z-flashing lower panel

Option 2

Figure 18 - Horizontal Band Board - Install a horizontal band board at the top of the bottom panel. Butt the lower batten to the band board and start the top

batten at the bottom edge of the top panel. Maintain a 1/4 in. clearance above horizontal flashing.

Figure 18

HardieTrim

Batten upper panel

Do not

Caulk

1/4 in. gap

Z-flashing

HardieTrim

Batten lower panel

TR1510_P5/9 03/15

INSTALLATION (cont.)

Fascia

HardieTrim board is a decorative non-load bearing trim product.

Do not use HardieTrim to replace any structural component

HardieTrim boards can be fastened directly over a 2x sub-fascia or directly to rather tails. Check local building code for relevant codes.

Option 1

Over sub-fascia: (figure 19)

When installing HardieTrim boards over solid 2x sub-fascia use minimum 2 in., 16 gauge corrosion resistant finish nails. (see fastener guide below) roofing

Figure 19 roof underlayment roof sheathing drip edge flashing

Gutters:

James Hardie recommends the use of rain gutters whenever possible.

roof framing

HardieTrim NT3 board sub fascia

HardieSoffit Panel

Do not attach gutters directly to HardieTrim

Use gutter hangers that attach through the roof sheathing into a rafter tail or other structural member.

Soffit

When installing HardieSoffit additional framing/blocking may be needed depending on application. Refer to HardieSoffit installation instructions for guidance.

Option 2

Direct to rafter tails: (figure 20)

When installing HardieTrim NT3 boards without the presence of a 2x sub-fascia, a minimum 8d siding corrosion resistant nails must be used to attach HardieTrim NT3 boards DO NOT use finish nails. (refer to fastener guide below).

Fascia Fastener Guide

HardieTrim

Board

6 in.

8 in.

10 in.

FASTENER SPACING

Direct to Rafter

(min 8d siding)

2 nails every rafter spaced max

24 in. O.C.

3 nails every rafter spaced max

24 in. O.C.

Over 2x Sub-fascia

(Minimum 2 in. 16 ga. Finish nails)

2 nails spaced maximum

16 in. O.C.

3 nails spaced maximum

16 in. O.C.

4 nails spaced maximum

16 in. O.C.

Figure 20

Roof

Sheathing

Roof Framing

Roofing

Roof

Underlayment

Style“D” dripedge

Flashing

HardieSoffit

Panel

HardieTrim NT3

Board

TR1510_P6/9 05/15

INSTALLATION (cont.)

HardieTrim

™

Tabs

Fastener Requirements

For Corners, Band Boards, Windows, and Door Applications:

HardieTrim NT3 boards may be installed with HardieTrim™ Flat Tabs and HardieTrim™ Corner Tabs which provide concealed fastening. Only HardieTrim Flat and

Corner Tabs can be used with HardieTrim NT3 boards to create a concealed fastening.

Step 1: Attach HardieTrim Flat Tabs to the back side of the trim using four, 18 ga. 1/2 in. L x 1/4 in. W narrow crown corrosion resistant staples, equally spaced in one row, positioned no closer than 1/2 in. from trim edges using a pneumatic staple gun. (figures 21 & 22)

Step 2: For wood frame construction, attach the trim to the building with minimum 2, 6d siding nails fastened through the HardieTrim Flat Tabs (figure23). ET&F or equivalent fasteners may be used to attach the HardieTrim Flat Tabs to steel frame construction.

Fastener spacing will vary based on application. Refer to fastener table on page 8. Refer to specific sections in these instructions for required fastener spacing by application (window, band board, etc.)

For Fascia, Rake, and Frieze board Applications:

HardieTrim tabs cannot be used in fascia, rake, or frieze board applications. Follow Face nailing fastening specifications.

Installation of HardieTrim tabs in Coastal Regions:

James Hardie requires that stainless steel staples & fasteners be used when installing HardieTrim Tabs in coastal regions.

Installation of HardieTrim Tabs over Pressure Treated Lumber: HardieTrim tabs shall not come in direct contact with ACQ or CA preservative-treated wood. Refer to the General Fastening section of this document for further information.

HardieTrim boards with ColorPlus Technology: Remove the laminate sheet as soon as possible after attaching the trim to the building.

Min 2 in.

Min 1/2 in.

Fasten 4 staples minimum ¼ in. from trim edge

Figure 21

Back view

16 in. O.C. max

HardieTrim Flat Tabs

Fasten HardieTrim

Flat Tab to minimum 7/16 in.

OSB with min 2, 6d siding nails

Figure 22

Front view

Figure 23

Trim Application for Windows, Doors & Other Openings

Trim the opening prior to the installation of the siding. Place a Flat Tab at the end of each trim board and one tab every 16 in. OC. Attach the trim boards and Flat Tabs around the opening as shown in figure 24. Use 16 ga. galvanized 2 in. long finish nails to ensure proper fastening if needed.

Figure 24

2 2

Flush

HardieTrim

Flat and

Corner Tabs

Siding nail attaches tab to the wall.

HardieTrim

Flat and Corner Tabs

Do not under drive nails.

Only use staples to fasten HardieTrim Flat and

Corner Tabs to the trim boards.

NOTE: Follow your window/door manufacturers installation instructions for caulking guidance between window and trim.

TR1510_P7/9 03/15

INSTALLATION (cont.)

Trimming Corners

When using HardieTrim tabs prebuild outside corners off the wall.

• Attach HardieTrim Corner Tabs to the back side of the trim using eight(8) - 18 ga. 1/2 in. L x 1/4 in. W narrow crown corrosion resistant staples using a pneumatic stapler. Ensure the HardieTrim Corner Tabs are fastened tight and straight to the trim boards. (figure 25)

• For wood frame construction, attach trim to building using min. 6d siding nails fastened through the HardieTrim Corner Tabs attached to minimum 7/16 in. OSB *. (figure 26)

• Attach a HardieTrim Corner Tab 1 in. from each ends and every 20 in. O.C.

• TIP: Creating a jig for the work station is recommended to ensure corners are fastened securely and straight. (ﬁgure 27)

Figure 25 Figure 25 Figure 19

Corner studs HardieTrim

Corner Tabs

Fasten 2 in. x 4 in.

timber blocks to a work bench

HardieTrim

Corner Tab

Use 4 staples per piece of trim to fasten the

L-shaped tab to the pre-built corner. Use the nail line on the tabs as a guide.

Siding nail

HardieTrim

Corner Tab

HardieTrim

NT3 Boards

Fasten 2 in. x 8 in. stud to the timber blocks

Band Board

Terminate ends of the Band Board into Trim or Siding or miter cut the edges of the trim at the corners of the building. Place a HardieTrim Flat Tab at the end of each trim board and one tab every stud at a maximum of 16 in. O.C. The HardieTrim Flat Tabs should be attached to the trim in an alternating pattern to the top and bottom of the band board (figures 21, 22). Use 16 ga. galvanized 2 in. long finish nails to ensure proper fastening if needed.

Trim Tab

Fastener Table

Application

Framing Material

Tab is nailed into

Wood Stud

(minimum G=0.42)

Flat Tab

Minimum APA rated

7/16 in. OSB

Minimum 20 gauge steel

Wood Stud

(minimum G=0.42)

Corner Tab

Minimum APA rated

7/16 in. OSB

Minimum 20 gauge steel

Fastener

(tab to framing)

One 6d corrosion resistant siding nail installed through center of tab into framing

Two 4d ring shank corrosion resistant siding nails equally spaced installed through tab into framing

One No. 8 X 1 in. long X 0.323 in. head diameter screw (corrosion resistant) installed through flange into framing

On each flange, Install one 6d corrosion resistant siding nail through tab into framing

On each flange, Install two 4d ring shank corrosion resistant siding nails through tab into framing

On each flange, Install one No. 8 X 1 in.

long X 0.323 in. head diameter screw

(corrosion resistant) through tab into framing

Fastener

(tab to trim)

Four 18 ga. X 1/2 in. long X 1/4 in. wide corrosion resistant crown staples, equally spaced in one row

For each piece of trim, install Four 18 ga. X

1/2 in. long X 1/4 in. wide corrosion resistant crown staples, equally space in two rows

Max Tab Spacing

(inches on center)

TR1510_P8/9 03/15

FINISHING

Cut Edge Treatment

Caulk, paint or prime all field cut edges. James Hardie touch-up kits are required to touch-up ColorPlus products.

Caulking

For best results use an Elastomeric Joint Sealant complying with ASTM C920 Grade NS, Class 25 or higher or a Latex Joint Sealant complying with ASTM C834. Caulking/Sealant must be applied in accordance with the caulking/sealant manufacturer’s written instructions. For best results use an Elastomeric Joint Sealant complying with ASTM C920 Grade NS, Class 25 or higher or a Latex Joint Sealant complying with ASTM C834.

Caulking/Sealant must be applied in accordance with the caulking/sealant manufacturer’s written instructions.

Painting

DO NOT use stain, oil/alkyd base paint, or powder coating on James Hardie Products. James Hardie products must be painted within 180 days for primed product and 90 days for unprimed. 100% acrylic topcoats are recommended. Do not paint when wet.

For application rates refer to paint manufacturers specifications. Back-rolling is recommended if the siding is sprayed.

ColorPlus Technology Caulking, Touch-up & Laminate

• Care should be taken when handling and cutting James Hardie ColorPlus products. During installation use a wet soft cloth or soft brush to gently wipe off any

residue or construction dust left on the product, then rinse with a garden hose.

• Touch up nicks, scrapes and nail heads using the ColorPlus Technology touch-up applicator. Touch-up should be used sparingly.

If large areas require touch-up, replace the damaged area with new HardieTrim board with ColorPlus Technology.

• Laminate sheet must be removed immediately after installation. Nail head touch-up can be done before or after removal of the laminate sheet when using ﬁnish

nails. The preferred method is to touch-up while the laminate sheet is in place. Remove the laminate sheet before paint dries.

• Terminate non-factory cut edges into trim where possible, and caulk. Color matched caulks are available from your ColorPlus product dealer.

• Treat all other non-factory cut edges using the ColorPlus Technology edge coaters, available from your ColorPlus product dealer.

Note: James Hardie does not warrant the usage of third party touch-up or paints used as touch-up on James Hardie ColorPlus products.

Problems with appearance or performance arising from use of third party touch-up paints or paints used as touch-up that are not James Hardie touch-up, will not be covered under the James Hardie ColorPlus Limited Finish Warranty.

Painting James Hardie Siding and Trim Products with ColorPlus Technology

When repainting ColorPlus products, James Hardie recommends the following regarding surface preparation and topcoat application:

• Ensure the surface is clean, dry, and free of any dust, dirt, or mildew

• Repriming is normally not necessary

• 100% acrylic topcoats are recommended

• DO NOT use stain, oil/alkyd base paint, or powder coating on James Hardie Products.

• Apply ﬁnish coat in accordance with paint manufacturers written instructions regarding coverage, application methods, and application temperature

• DO NOT caulk nail heads when using ColorPlus products, refer to the ColorPlus touch-up section

RECOGNITION: HardieTrim boards may be installed as an equal alternative to conventional trim permitted for use in; 2006, 2009, & 2012 International Building Code, Section 1402.1, and the 2006, 2009, & 2012

International Residence Code for One - and Two - Family - Dwellings, Section R703.1.

TM, SM, and ® denote trademarks or registered trademarks of

James Hardie Technology Limited. is a registered trademark of James Hardie Technology Limited.

Additional Installation Information,

Warranties, and Warnings are available at www.jameshardie.com

TR1510_P9/9 03/15

Boards

INSTALLATION REQUIREMENTS - 4/4, 5/4, BATTENS, PRIMED & COLORPLUS ® PRODUCTS

EFFECTIVE MAY 2015

Visit www.jameshardie.com

for the most recent version.

These instructions are to be used for HardieTrim ® HZ ™ Boards ONLY and are ONLY VALID in the following states: WA, OR, CA, NV, UT, ID, CO, WY, MT, AZ, NM.

IMPORTANT: FAILURE TO INSTALL AND FINISH THIS PRODUCT IN ACCORDANCE WITH APPLICABLE BUILDING CODES AND JAMES HARDIE WRITTEN

APPLICATION INSTRUCTIONS MAY LEAD TO PERSONAL INJURY, AFFECT SYSTEM PERFORMANCE, VIOLATE LOCAL BUILDING CODES, AND VOID THE

PRODUCT ONLY WARRANTY. BEFORE INSTALLATION, CONFIRM THAT YOU ARE USING THE CORRECT HARDIEZONE INSTRUCTIONS. INSTALLATION OF

HZ PRODUCTS OUTSIDE AN HZ LOCATION WILL VOID YOUR WARRANTY. TO DETERMINE WHICH HARDIEZONE APPLIES TO YOUR LOCATION,

VISIT WWW.HARDIEZONE.COM OR CALL 1-866-942-7343 (866 9HARDIE)

STORAGE & HANDLING: CUTTING INSTRUCTIONS

Store flat and keep dry and covered prior to installation. Installing James Hardie siding product wet or saturated may result in shrinkage at butt joints. Carry product on edge.

OUTDOORS

1. Position cutting station so that wind will blow dust away from user

and others in working area.

2. Use one of the following methods:

a. Better: i. Dust reducing circular saw equipped with a

HardieBlade ® saw blade and HEPA vacuum extraction

b. Good: i. Dust reducing circular saw with a HardieBlade saw blade

(only use for low to moderate cutting)

INDOORS

- NEVER use a power saw indoors

- NEVER use a circular saw blade that does not carry the HardieBlade

saw blade trademark

- NEVER dry sweep – Use wet suppression or HEPA Vacuum

Protect edges and corners from breakage.

James Hardie is not responsible for damage caused by improper storage and handling of the product.

SD083105

HardieTrim

boards are decorative non-load bearing trim products.

Do not use HardieTrim boards to replace any structural component.

GENERAL REQUIREMENTS

• Wood or steel must be provided for attaching HardieTrim boards.

• Follow all applicable codes when installing HardieTrim boards.

• DO NOT install HardieTrim boards, such that they may remain in contact with standing water.

• DO NOT use stain, oil/alkyd base paint, or powder coating on James Hardie Products.

INSTALLATION INSTRUCTIONS MAY LEAD TO SERIOUS PERSONAL INJURY OR DEATH.

SD050905

TR1509_P1/9 03/15

FLASHING/CLEARANCE REQUIREMENTS NO-COVER

HardieTrim may be installed with a minimum

1/4 in. clearance when installed vertically to grade, decks, paths, steps, and driveways

Maintain a minimum 1 in. horizontal clearance between James Hardie trim products and decks, paths, steps and driveways.

Figure 2 Figure 3 horizontal trim

6 in. min.

siding water resistive barrier flashing trim deck material

1 in. min.

joist flashing ledger vertical trim

1/4 in. min.

Maintain a 1/4 in. clearance between the bottom of James Hardie products and horizontal flashing. Do not caulk gap.

Figure 5 siding

Do not

Caulk

1/4 in. gap

Drip Edge

Figure 6

At the juncture of the roof and vertical surfaces, flashing and counter flashing shall be installed per the roofing manufacturer’s instructions. Provide a 1 in. clearance between the roofing and the bottom edge of the trim.

Figure 4 trim

1 in.

min.

flashing for fascia installation see page 6

Mortar/Masonry

Figure 7

L-Flashing

Z-Flashing flashing

Block Penetration

Figure 8

Z-Flashing

Valley/Shingle Extension

Figure 9

Extend shingles at least 1 in. out from the fascia when gutters are present

CLEARANCE REQUIREMENTS UNDER-COVER

Figure 10 Maintain a 1/4 in. clearance for

HardieTrim boards installed under cover.

Under cover is defined as:

• Not more than 10 feet below a roof overhang, and

• Not less than 4 inches horizontally from the edge of the roof overhang

4 in. min.

1/4 in. min. clearance

10 ft. max

TR1509_P2/9 03/15

FASTENING

General Fastening Requirements

Fasteners must be corrosion resistant, galvanized, or stainless steel.

Electro-galvanized are acceptable but may exhibit premature corrosion.

James Hardie products near the ocean, large bodies of water, or in very humid climates.

Manufacturers of ACQ and CA preservative-treated wood recommend spacer materials or other physical barriers to prevent direct contact of

ACQ or CA preservative-treated wood and aluminum products.

Pneumatic Fastening

James Hardie products can be hand nailed or fastened with a pneumatic tool.

Flush Snug Flush

Figure A

Finish Nail

Figure B

Siding Nail do not over drive siding nails do not under drive nails

Face Nailing Requirements

Use 2 in. minimum 16 ga. finish nails to attach HardieTrim boards to wood frame construction. ET&F or equivalent fasteners or screws may be used to attach

HardieTrim boards to steel frame construction.

James Hardie recommends using stainless steel finish nails when installing HardieTrim products.

Minimum fastener guide for finish nailing:

Pre-built corner Site Built Corners

4 in.

6 in.

8 in.

12 in.

1 nail every 16 in. to attach boards together + 1 nail every 16 in. each board

1 nail every 16 in. to attach boards together + 2 nails every 16 in. each board

2 nails every 16 in.

3 nails every 16 in.

4 nails every 16 in.

Other areas (e.g. window trim, and band boards)

2 nails every 16 in.

3 nails every 16 in.

Use a 2 in. finish nail to fasten trim together. Longer finish nails may bend.

plywood or

OSB sheathing

1 in. from ends water-resistive barrier

16 in. O.C. maximum finish nailing pattern

*Follow all applicable codes when installing HardieTrim boards

Figure 11

Vertical trim may be installed with a 1/4 in. min. clearance*.

Leave a minimum 1/8 in. gap between the siding and trim, then caulk.

TR1509_P3/9 03/15

INSTALLATION

Trimming Corners

When installing corners or other vertical trim, position boards on the wall and attach (figure 12).

Pre-Built Corners

Alternatively, corners can be pre-built off the wall using 2 in. finishing nails. Each side of the pre-built corner must be secured to the wall (figure 13).

Figure 12

2 in. Finish nail corner studs

Trim application for windows, doors & other openings

Flashing over trim is required per code for all installation methods. (figure 14) flashing over trim do not caulk along top edge

HardieTrim board

Figure 14

Figure 13

2 in. Finish nail corner studs waterresistive barrier siding

Butt to Siding

Trim the opening prior to the installation of the siding.

Position trim boards on the wall and secure. Allow proper fastener spacing at edges and ends.

16 in. max.

Butt to Siding

Horizontal

Flashing

NOTE: Follow your window/door manufacturer’s installation instructions for caulking guidance between window and trim.

leave a minimum 1/8 in. gap between siding and trim, then caulk.

Frieze Boards

HardieTrim boards can be used as frieze board. (figure 16)

Band Board

For band board applications, a flashing is required over the trim. (figure 15) sheathing

Figure 15 blocking/support if required water resistive barrier lap siding

1/4 in. gap flashing

HardieTrim board

Figure 16

HardieTrim frieze board

HardieTrim frieze board caulk if required

HardiePlank lap siding Butt-to Siding

Shim behind trim

Trim Over Siding

TR1509_P4/9 03/15 65

INSTALLATION (cont.)

Batten Boards

Horizontal Panel Joints

At horizontal panel joints HardieTrim battens must be installed according to option 1 or 2 below.

When installing HardieTrim Battens horizontally, they must be installed as a panel joint according to option 2.

Option 1

Figure 17 - No horizontal band board - Make a 22.5- 45 degree weather cut, in the HardieTrim batten, just above the 1/4 in. clearance between panels.

Figure 17 HardieTrim

Batten upper panel

Do not

Caulk

1/4 in. gap

Z-flashing lower panel

Option 2

Figure 18 - Horizontal Band Board - Install a horizontal band board at the top of the bottom panel. Butt the lower batten to the band board and start the top

batten at the bottom edge of the top panel. Maintain a 1/4 in. clearance above horizontal flashing.

Figure 18

HardieTrim

Batten upper panel

Do not

Caulk

1/4 in. gap

Z-flashing

HardieTrim

Batten lower panel

TR1509_P5/9 03/15

INSTALLATION (cont.)

Fascia

HardieTrim board is a decorative non-load bearing trim product.

Do not use HardieTrim to replace any structural component

HardieTrim boards can be fastened directly over a 2x sub-fascia or directly to rather tails. Check local building code for relevant codes.

Option 1

Over sub-fascia: (figure 19)

When installing HardieTrim boards over solid 2x sub-fascia use minimum 2 in., 16 gauge corrosion resistant finish nails. (see fastener guide below) roofing

Figure 19 roof underlayment roof sheathing drip edge flashing

Gutters:

James Hardie recommends the use of rain gutters whenever possible.

roof framing

HardieTrim board sub fascia

HardieSoffit Panel

Do not attach gutters directly to HardieTrim

Use gutter hangers that attach through the roof sheathing into a rafter tail or other structural member.

Soffit

When installing HardieSoffit additional framing/blocking may be needed depending on application. Refer to HardieSoffit installation instructions for guidance.

Option 2

Direct to rafter tails: (figure 20)

When installing HardieTrim boards without the presence of a 2x sub-fascia, a minimum 8d siding corrosion resistant nails must be used to attach HardieTrim boards

DO NOT use finish nails. (refer to fastener guide below).

Fascia Fastener Guide

HardieTrim

Board

6 in.

8 in.

10 in.

FASTENER SPACING

Direct to Rafter

(min 8d siding)

2 nails every rafter spaced max

24 in. O.C.

3 nails every rafter spaced max

24 in. O.C.

Over 2x Sub-fascia

(Minimum 2 in. 16 ga. Finish nails)

2 nails spaced maximum

16 in. O.C.

3 nails spaced maximum

16 in. O.C.

4 nails spaced maximum

16 in. O.C.

Figure 20

Roof

Sheathing

Roof Framing

Roofing

Roof

Underlayment

Style“D” dripedge

Flashing

HardieSoffit

Panel

HardieTrim

Board

TR1509_P6/9 05/15

INSTALLATION (cont.)

HardieTrim

™

Tabs

Fastener Requirements

For Corners, Band Boards, Windows, and Door Applications:

HardieTrim boards may be installed with HardieTrim™ Flat Tabs and HardieTrim™ Corner Tabs which provide concealed fastening. Only HardieTrim Flat and Corner

Tabs can be used with HardieTrim boards to create a concealed fastening.

Step 2: For wood frame construction, attach the trim to the building with minimum 2, 6d siding nails fastened through the HardieTrim Flat Tabs (figure 23). ET&F or equivalent fasteners may be used to attach the HardieTrim Flat Tabs to steel frame construction.

Fastener spacing will vary based on application. Refer to fastener table on page 9. Refer to specific sections in these instructions for required fastener spacing by application (window, band board, etc.)

For Fascia, Rake, and Frieze board Applications:

HardieTrim tabs cannot be used in fascia, rake, or frieze board applications. Follow Face nailing fastening specifications.

Installation of HardieTrim tabs in Coastal Regions:

James Hardie requires that stainless steel staples & fasteners be used when installing HardieTrim Tabs in coastal regions.

HardieTrim boards with ColorPlus Technology: Remove the laminate sheet as soon as possible after attaching the trim to the building.

Figure 21

Back view

Min 2 in.

Min 1/2 in.

16 in. O.C. max

Fasten 4 staples minimum ¼ in. from trim edge

HardieTrim Flat Tabs

Figure 23

Fasten HardieTrim

Flat Tab to minimum 7/16 in.

OSB with min 2, 6d siding nails

Figure 22

Front view

Trim Application for Windows, Doors & Other Openings

Figure 24

2 2

Flush

HardieTrim

Flat and

Corner Tabs

Siding nail attaches tab to the wall.

HardieTrim

Flat and Corner Tabs

Do not under drive nails.

Only use staples to fasten HardieTrim Flat and

Corner Tabs to the trim boards.

NOTE: Follow your window/door manufacturers installation instructions for caulking guidance between window and trim.

TR1509_P7/9 03/15

INSTALLATION (cont.)

Fascia

HardieTrim board is a decorative non-load bearing trim product.

Do not use HardieTrim to replace any structural component

HardieTrim boards can be fastened directly over a 2x sub-fascia or directly to rather tails. Check local building code for relevant codes.

Option 1

Over sub-fascia: (figure 19)

When installing HardieTrim boards over solid 2x sub-fascia use minimum 2 in., 16 gauge corrosion resistant finish nails. (see fastener guide below) roofing

Figure 19 roof underlayment roof sheathing drip edge flashing

Gutters:

James Hardie recommends the use of rain gutters whenever possible.

roof framing

HardieTrim board sub fascia

HardieSoffit Panel

Do not attach gutters directly to HardieTrim

Use gutter hangers that attach through the roof sheathing into a rafter tail or other structural member.

Soffit

When installing HardieSoffit additional framing/blocking may be needed depending on application. Refer to HardieSoffit installation instructions for guidance.

Option 2

Direct to rafter tails: (figure 20)

When installing HardieTrim boards without the presence of a 2x sub-fascia, a minimum 8d siding corrosion resistant nails must be used to attach HardieTrim boards

DO NOT use finish nails. (refer to fastener guide below).

Fascia Fastener Guide

HardieTrim

Board

6 in.

8 in.

10 in.

FASTENER SPACING

Direct to Rafter

(min 8d siding)

2 nails every rafter spaced max

24 in. O.C.

3 nails every rafter spaced max

24 in. O.C.

Over 2x Sub-fascia

(Minimum 2 in. 16 ga. Finish nails)

2 nails spaced maximum

16 in. O.C.

3 nails spaced maximum

16 in. O.C.

4 nails spaced maximum

16 in. O.C.

Figure 20

Roof

Sheathing

Roof Framing

Roofing

Roof

Underlayment

Style“D” dripedge

Flashing

HardieSoffit

Panel

HardieTrim

Board

TR1509_P6/9 05/15

FINISHING

Cut Edge Treatment

Caulk, paint or prime all field cut edges. James Hardie touch-up kits are required to touch-up ColorPlus products.

Caulking

Caulking/Sealant must be applied in accordance with the caulking/sealant manufacturer’s written instructions.

Painting

For application rates refer to paint manufacturers specifications. Back-rolling is recommended if the siding is sprayed.

ColorPlus Technology Caulking, Touch-up & Laminate

• Care should be taken when handling and cutting James Hardie ColorPlus products. During installation use a wet soft cloth or soft brush to gently wipe off any

residue or construction dust left on the product, then rinse with a garden hose.

• A ﬁnish nail is required for installing 4/4 and 5/4 HardieTrim boards.

• Touch up nicks, scrapes and nail heads using the ColorPlus Technology touch-up applicator. Touch-up should be used sparingly.

If large areas require touch-up, replace the damaged area with new HardieTrim board with ColorPlus Technology.

• Laminate sheet must be removed immediately after installation. Nail head touch-up can be done before or after removal of the laminate sheet when using ﬁnish

nails. The preferred method is to touch-up while the laminate sheet is in place. Remove the laminate sheet before paint dries.

• Terminate non-factory cut edges into trim where possible, and caulk. Color matched caulks are available from your ColorPlus product dealer.

• Treat all other non-factory cut edges using the ColorPlus Technology edge coaters, available from your ColorPlus product dealer.

Note: James Hardie does not warrant the usage of third party touch-up or paints used as touch-up on James Hardie ColorPlus products.

Painting James Hardie Siding and Trim Products with ColorPlus Technology

When repainting ColorPlus products, James Hardie recommends the following regarding surface preparation and topcoat application:

• Ensure the surface is clean, dry, and free of any dust, dirt, or mildew

• Repriming is normally not necessary

• 100% acrylic topcoats are recommended

• DO NOT use stain, oil/alkyd base paint, or powder coating on James Hardie Products.

• Apply ﬁnish coat in accordance with paint manufacturers written instructions regarding coverage, application methods, and application temperature

• DO NOT caulk nail heads when using ColorPlus products, refer to the ColorPlus touch-up section

International Residence Code for One - and Two - Family - Dwellings, Section R703.1.

TM, SM, and ® denote trademarks or registered trademarks of

James Hardie Technology Limited. is a registered trademark of James Hardie Technology Limited.

Additional Installation Information,

Warranties, and Warnings are available at www.jameshardie.com

TR1509_P9/9 03/15

Witaj! Jestem chatbotem AI specjalnie przeszkolonym, aby pomóc Ci w obsłudze James Hardie 667404 HardieTrim HZ5 1 in. x 3.5 in. x 144 in. Fiber Cement Smooth ColorPlus Trim Board manual. Dokładnie przejrzałem dokument i mogę pomóc Ci zlokalizować dokładne informacje, których potrzebujesz, lub wyjaśnić treść w jasny i prosty sposób. Niezależnie od tego, czy szukasz wskazówek dotyczących konkretnych funkcji, kroków rozwiązywania problemów, czy ogólnego użytkowania, możesz zadawać pytania. Im więcej szczegółów podasz na temat swoich obaw lub potrzeb, tym dokładniej i skuteczniej mogę Ci pomóc!

Asystent pisze

Asystent jest niedostępny. Spróbuj ponownie później.

Wygląda na to, że dotarłeś do dokumentu napisanego w wielu językach, w tym w języku, który nie jest Twoim językiem ojczystym. Możesz użyć poniższych linków, aby tymczasowo ukryć strony bez preferowanego języka.

Reklama

HardieTrim

®

Boards Products Description

! WARNING

CONCEALED FASTENING TABS

TRIMMING CORNERS

TRIM APPLICATION FOR WINDOWS, DOORS & OTHER OPENINGS

BAND BOARD

FASTENER TABLE

OUTSIDE CORNERS

INSIDE CORNERS

BAND BOARD

HARDIETRIM 5/4, 4/4 BOARDS FASTENER SPECIFICATIONS

7

10

11

12

WINDOW AND DOOR TRIM

INSTALLING RAKE AND FASCIA BOARD

DRIP EDGE

GETTING STARTED

ColorPlus

TIP:

HARDIETRIM BATTENS FASTENING SPECIFICATIONS

HORIZONTAL JOINT TREATMENT

STORAGE & HANDLING: CUTTING INSTRUCTIONS

HardieTrim

NT3

boards are decorative non-load bearing trim products.

TABLE OF CONTENTS:

GENERAL REQUIREMENTS

Face Nailing Requirements

Trimming Corners

Trim application for windows, doors & other openings

Butt to Siding

Frieze Boards

Band Board

Batten Boards

Horizontal Panel Joints

Fascia

Fascia Fastener Guide

HardieTrim

Tabs

Cut Edge Treatment

Caulking

Painting

ColorPlus Technology Caulking, Touch-up & Laminate

Painting James Hardie Siding and Trim Products with ColorPlus Technology

Boards

STORAGE & HANDLING: CUTTING INSTRUCTIONS

HardieTrim

boards are decorative non-load bearing trim products.

TABLE OF CONTENTS:

GENERAL REQUIREMENTS

Face Nailing Requirements

Trimming Corners

Trim application for windows, doors & other openings

Butt to Siding

Frieze Boards

Band Board

Batten Boards

Horizontal Panel Joints

Fascia

Fascia Fastener Guide

HardieTrim

Tabs

Fascia

Cut Edge Treatment

Caulking

Painting

ColorPlus Technology Caulking, Touch-up & Laminate

Painting James Hardie Siding and Trim Products with ColorPlus Technology

Powiązane

James Hardie 9000038 Hardie Trim HZ10 1 in. x 3.5 in. x 12 ft. Primed Fiber Cement Smooth Trim Board Product Manual

HardieTrim 5/4, 4/4, Batten: AI Chat & PDF Access

HardieTrim 5/4, 4/4 Boards Inst. | IA Chat & PDF Download

Builders FirstSource Aluminum Mounting Flange Windows Installation Instructions

James Hardie NT3 Boards Panels User Manual: AI Chat & PDF

James Hardie Trim Boards Manual | AI Chat & PDF

lowes FLC-GRK-PG32-RSS Rugged Structural Screws Instructions