Two-Channel Remote Intercom Station

Two-Channel Remote Intercom Station
RM-220
RM-220 Front Panel
shown with optional gooseneck mic
F E AT U R E S
• Selectable one- or two-channel
communication
• Individual listen volume controls
• Momentary/latching talk buttons
• Individual call buttons
RM-220 Back Panel
• Visual call signaling
• Balanced audio input with
program interrupt (IFB)
• “Hot mic” and line-level outputs
• Studio announce output
with relay
• Optional plug-in gooseneck mic
• Wide-range hi-output speaker
• One rack space
A P P L I C AT I O N S
• ENG and EFP trucks
• Production studio consoles
• Single-channel program interrupt
system “IFB” for talent cueing
• Portable sound system equipment
racks
• Low-profile “top of console”
locations
• Any 2-channel intercom requirement where rack space is at a
premium
DESCRIPTION
The RM-220 is one of a series of professional remote intercom stations.
The remote speaker/headset station allows two-channel selectable talk and listen
in one rack space. The operator can talk and listen on either channel separately
or talk to both channels simultaneously without tying the two channels together.
Specially contoured audio response provides excellent speech intelligibility, even
in high-noise environments.
The RM-220 can monitor intercom activity on one or both channels with
individual Listen Level controls. Monitor intercom activity through a headset,
the internal speaker, or both at once. The 4-watt output amplifier can drive the
wide- response speaker or Clear-Com headset to very high output levels--more
than enough volume for the noisiest environment. A “speaker dipping” circuit
helps to reduce feedback when stations are placed in close proximity to each other.
The station has a convenient speaker “on/off” switch when private conversation
via the headset is desired. The station accepts dynamic headsets or optional plug-in
gooseneck mic.
TA L K S E L E C T I O N
The operator can talk on either of the channels separately or on both at once.
A proprietary contoured frequency response in the mic pre-amp enhances speech
intelligibity in high-noise environments. Illuminated dual-action talk buttons are
electronic momentary or latching. The latching feature may be disabled if desired.
The station also features a headset or microphone selector switch. The talk buttons
can also be remote controlled with a footswitch.
®
PROFESSIONAL INTERCOM PRODUCTS
by Clear-Com
Two-Channel Remote Intercom Station
SIGNALING
The RM- 220 features individual call
buttons and visual call signaling to attract
the attention of operators who have
removed their headsets or turned off their
speakers. The visual signaling flashes the
illuminated talk button when a call is
received. The call-signaling feature can
be programmed to the talk buttons.
AUX. AUDIO INPUT AND
P RO G R A M I N T E R R U P T ( I F B )
The station can accept either a balanced or unbalanced line-level audio
input through the DB-15 connector
on the rear panel. The program can be
monitored at the station or fed into
channel B, where it can also be set up
for IFB/Program interrupt from this or
any other PL-Pro-series station.
A D D I T I O N A L F E AT U R E S
Each channel has its own sidetone
control. This allows the operator to vary
the level of their own voice as heard in
the headset. When the announce button
is pressed, the microphone signal is routed to a connector on the back panel.
Relay contacts are also available for muting speakers or turning on a signal light.
The station accepts Clear-Com’s 9”
or 18” gooseneck microphone.
RM-220
S P E C I F I C AT I O N S
CONTROL SYSTEM
CMOS digital logic
AUDIO OUTPUTS
Announce Output: 0 dB, 600 Ω
transformer balanced
Hot Mic Output: 0 dB, 100 Ω unbalanced
MIC PREAMP
Adjustable gain with limiter
Frequency Response: 250 Hz - 12 kHz,
contoured for maximum intelligibility
Limiter Range: 20 dB
Mic Pre-Amp Gain: +41 dB
HEADPHONE AMPLIFIER
Output: Load 50 - 2,000 Ω
Level: +20 dBv @ 600 Ω
Distortion: <0.2% THD @ 1 kHz
Frequency Response: 200 Hz - 18 kHz
Gain from intercom line: +37dB
SPEAKER AMPLIFIER
8 watts
EXTERNAL AUDIO PROGRAM
Electronically balanced
Input Level: -10 dBv
Impedance: 40K, bridging
Frequency Response: 150 Hz - 15 kHz
HEADSET TYPE
Microphone: Dynamic
Level: -55 dB
Impedance: 200 Ω
Headphone: Impedance: 50 - 2,000 Ω
MICROPHONE INPUT
Electret with proprietary speech shaping
circuit
Plug-in 9” or 18” gooseneck mic, optional
INTERCOM LINE DRIVE/RECEIVE
CIRCUITS
Bridging Impedance: >10K Ω
Intercom Line Level: -9 dBv; + 5 dBv max.
Sidetone Null: >25 dB
SYSTEM SPECIFICATIONS
Intercom Line Length: 5,000 ft. max., 1
channel
Intercom line length: 1,000 ft. for <50 dB
crosstalk, 2 channels
RELAY
Announce: SPDT
Contact rating: 24 Volts DC @ 1 amp
TALK REMOTE CONTROL
Two logic inputs
REAR PANEL CONNECTORS
(2) XLR-3: Channel A
(2) XLR-3: Channel B
1⁄4” Phone Jack: Hot Mic Out
Female DB-25:
AudioProgram Input
Announce Relay Contacts
Announce Output
Footswitch contacts
DIMENSIONS & WEIGHT
1.75” H (1 RU) x 19” W x 6.5” D
(44 x 483 x 165mm)
Depth not including rear panel connectors.
Weight: 7.5 lbs (3.4 kg)
POWER
100 mA average, from intercom line
0 dBv is referenced to 0.775 volts RMS
All specifications are subject to change without notice.
RM-220 BLOCK DIAGRAM
ANNOUNCE
ANNOUNCE
OUTPUT
MIC OUT
HEADSET MIC
SIDETONE
PANEL MIC
(OPTIONAL)
TALK
EQ/
LIM
MIC
ADJ.
TALK
HEADSET/PANEL
SELECT
PROGRAM
INT. LEVEL
= ANALOG CMOS SWITCH
BALANCED
PROGRAM
INPUT
HEADSET OUTPUT
RELAY CONTACT
EQ/
LIM
PGM
CHANNEL
B
CHANNEL A
LISTEN
3-PIN PL
CONNECTOR
CURRENT
SOURCE
CALL
SENSE
CALL
SEND
SIDETONE
CURRENT
SOURCE
CALL
SENSE
CALL
SEND
SPEAKER
SPEAKER
MUTE CIRCUIT
PROGRAM
VOLUME
CHANNEL B
LISTEN
3-PIN PL
CONNECTOR
Clear-Com Intercom Systems: 4065 Hollis Street, Emeryville, CA 94608-3505
(510) 496-6666, Fax (510) 496-6699, www.clearcom.com
International Sales: PO Box 302, Walnut Creek, CA 94597, (925) 932-8134, Fax (925) 932-2171
© 1998 Clear-Com Intercom Systems. PL-Pro is a Registered Trademark of Clear-Com. #RM220/1198
SPEAKER
ON/OFF
INTERRUPT
ANNC. IFB
AUTO
CALL
PROGRAM
INT. ENABLE
B
B
A
CONTROL LOGIC
TALK
MOMENTARY
B
A
B