- Industrial & lab equipment
- Measuring, testing & control
- Amprobe
- THWD-1 Digital Sling Psychrometer
- Manual
advertisement
▼
Scroll to page 2
of 4
Pt. No. 97570 9/94 OPERATING INSTRUCTIONS Digital Sling Psychrometer Model THWD-1 ISO-9002 SYSTEM CERTIFIED Á aurrose INSTRUMENT* DIVISION OF CONE INDUSTRIES IC E... TA le PA HA a mA pa LIMITED WARRANTY Congratulations! You are now the owner of an. AMPROBE® Instrument. It has been quälify.crafted according to quälity standards and contains quality . = = В Components and Workmanship. This ins ment has been inspected for proper operation of all of its ‚functions. It Nas been tested by qualified factory technicians according to the long- established standards of AMPROBE INSTRUMENT. Your AMPROBE instrument has a limit- ed warranty agáinst defective materials and/or workmanship for one year from the date of purchase provided that, in the opinion of the factory, the instru- ment has not been tampered with or taken apart. - Should your instrument fail due to defective materials, and/or workman- ship during the one-year warranty - period, return it along with a copy of your dated bill of sale which must identify instrument by model number and serial number. For your protection, please use the instrument as soon as possible. If damaged, or should the need arise to return your instrument, it must be securely wrapped (to prevent damage in transit) and sent prepaid via Air Parcel Post insured or UPS where available to: * 6 _ Service Division AMPROBE INSTRUMENT 630 Merrick Road (For U.PS.) Р.О. Вох 329 (Рог РР.) Lynbrook, NY 11563-0329 Outside the U.S.A. the local Amprobe representative will assist you. The above limited warranty covers repair and replace- ment of instrument only and no other oblig- ation is stated or implied. TO teva fle a MAA REN A a TE .. [A Specifications Temperature -20 to 50°C, Range: . -4 to 122°F + Accuracy: 11°C, £1°F «Resolution: 0.1%C, 0.1%F * Humidity (RH) 0 to 100% RH, Accuracy: +3% @ 25C from 10% to 90% RH, +4% all other ranges. * Memory, Min/Max * Wet bulb temperature | *Dew point measurement ~~ + * Response time: 60 seconds typical. * Battery: AAA Alkaline, 2 pes. included. * Data hold * F/C switch * Low battery indicator * Auto power off * Size: .13”(H) x 1.9"(W) x 6.7" (L)16.5mm(H) x 48.5 mm (W) x 170mm L * Sensor cover with pocket clip AMPROBE INSTRUMENT MODEL THWD-1 INSTRUCTIONS (1) Remove protective Sensor cover. (2) Turn meter on by pressing ON/OFF utton (3) Press C/F key to convert reading to desired range. Both temperatura and relative humidity measurement will display simultaneously, MIN/MAX FUNCTION (1) Press and hold MN/MAX button until (MIN) appears on display. Display is now showing minimum humidity and temperature reading in memory. (2) Press and hold MN/MX button again until (MAX) appears in dis play. Display is now showing maxi mum humidity and temperature readings in memory. ° (3) То гешт to current temperature - and humidity readings press and “hold MN/MX button until Min or Max disappears from display. (4) To clear current MIN and MAX readings from memory press and hold reset button until entire dis- play flashes. DATA HOLD FUNCTION Press hold button until (HOLD) appears in display. The current read- ing is now being held and will not change until HOLD function is can- celled. Press reset button to cancel HOLD function. HOLD function can be used for temperature, humidity, dew point, and wet bulb. DEW POINT FUNCTION: Press and hold (td/WBT) button until td appears on left side of display. Unit - Will now display Dew Point temp. — WET BULB FUNCTION: Press and hold (td/WTB) button until WB appears on left side of display. - Unit will now display Wet Bulb temper- ature. Intermittent flashing of WB indi- Cates that current reading is being cal- culated and updated due to constant changes in humidity and temperature in environment. TO EXIT DEW POINT/WET BULB FUNCTION Press and hold td/WTB button until td or WB disappears from display. AUTO POWER OFF FEATURE Unit will turn itself off after 20 minutes, (Sleep Mode). To override Auto Power Off functions (NON-SLEEP MODE) press ON/OFF and MIN/MAX button simuitaneously. After the full display appears release ON/OFF button, the display will show “n” in the display. When “n” appears then release MIN/MAX button. Unit will now be in Non-Sieep Mode. LO-BATTERY INDICATOR Lo-Battery Indication is signaled by the entire display flashing. This is the sig- nal to replace batteries at once: Failure to replace batteries will have an effect on the accuracy of the readings received from the hygrometer. NOTE: Remember low batteries will tend to give inaccurate readings. So make sure you have good batteries. CAUTION: Please do not immerse probe into liquids as this will cause permanent damage to the sensor. TE EAE FRE ka a a = a” у a - x . TROUBLESHOOTING If there appears to be a malfunction during the operating of the instrument, the following steps should be per- formed in order to isolate the cause o the problem. (1) Check the battery, (2) Review operating instructions for possible mistakes in operating procedure. a (3) If the instrument still malfunctions, place it with packing slip along with à brief description of the problem in sufficient cushioning material in a shipping carton. Be sure to indicate the serial number located on the back of the instrument. Amprobe is not responsible.for damage in transit. Make certain your name and address also appears on the box as well as packing slip; ship prepaid via U.P.S. (where available) or Air Parcef Post insured fo: . Service Division AMPROBE INSTRUMENT 630 Merrick Road (For U.PS.) P.O. Box 329 (For PP) Lynbrook, NY 11563-0329 Outside the USA, the local Amprobe representative will assist you. NOTES
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project