advertisement
® HDMI 2x2 UTP MATRIX SWITCH EXTENDER OVER ONE CAT5e/6
2x2 HDMI Matrix Switcher over Cat5e/6 designed to work as a switcher/splitter for multiple Audio/Video sources and displays. The unit is capable of switching HDMI signals up to 125 ft @ 1080/60p using 24 AWG Cat6 cable among two sources (such as: BluRay player, HD set top boxes, game systems, etc.) and two HDMI displays.
- Allows up to 2 HDMI sources to be independently switched to 2 UTP outputs
- Transmission Distance 125ft @ 1920x1080 over 24 AWG Cat6 cable with HDMI Active Receiver
- HDMI Compliant (Bandwidth = 225MHz)
- HDCP compliant
- Supports port selection by IR control and push button
- Supports IR and RS232 phone jack connector
• Matrix Switch
• (2) Surface mountable bracket
• (1) Power Adapter
• (4) Screw
• (1) Remote controller
• (1) User manual
• (1) DB9 Male to 3.5mm male cable
• (1) IR 3.5mm male cable
Step 2b.
If you plan to use
RS-232 Serial Control, connects the HDMI matrix to super terminal PC using
RS232 cable
Step 1.
Connects the
HDMI matrix switch to the source (up to 2) using HDMI cable
Source
DVD/BD Player
(Source 1)
Step 2a.
Connects the
HDMI matrix switch to the receivers using
Cat5e/6 cable
TER
HDMI
TRANSMIT
UTP EXTENDER
POWER OUTPUT
HDTV 2
HD Satellite
(Source 2)
HDTV 1
Power
RECEIVER
HDTV 1
Passive
Cat6 Cable up to 50 ft
Resolution up to 1080/60p or
Active
Cat6 Cable up to 125 ft
Resolution up to 1080/60p or or
Activity
Power
56
7 01
EQ
HDTV 2
RECEIVER
Power
Step 4a.
How to switch manually:
1. Push switch 1 button for
Passive
24 AWG Cat6 Cable up to 50 ft
Resolution up to 1080/60p input A to output 1.
Step 4b.
Push switch 1 again for input
POWER SWITCH 1
1 A
INPUT
B
OUTPUT 1 SWITCH 2
2 A
INPUT
B
OUTPUT 2 IR RS232
RESET
How to switch from remote:
B to output 1, etc.
Button 1 cycles input for output 1,
2. Push reset button to reset.
Button 2 cycles input for output 2, etc.
For RS-232 Serial Control Installation
Step 1.
Please make sure your Terminal
Emulator
Software is running
Step 2.
Setup your serial
COM port. Open your software and click setup and select Serial port from the drop down menu
Active
24 AWG Cat6 Cable up to 125 ft
Resolution up to 1080/60p
Step 3.
Select the COM port the DB9 is plugged into. If you use keyspan, it will automatically assigned the COM port for you.
Please make sure to select
Baud rate: 57600, Data:8bit,
Parity:None, Stop:1bit, Flow control: None and Click OK
Step 4.
Configure your software to allow input control. Click setup and select
Terminal from the drop down menu
Step 5.
Select LF on Receive in
New-Line; Set local echo:
You can enter the command and click OK.
POWER SWITCH 1
1
A
INPUT
B
OUTPUT 1 SWITCH 2
2
A
INPUT
B
OUTPUT 2
IR RS232 RESET
Step 3.
Connects the
HDMI matrix switch to the power
® HDMI 2x2 MATRIX UTP WITH RS-232 FUNCTION
COMMAND
Sw1 x1
Sw2 x1
PWD
STE
COMMANDS FOR SERIAL CONTROL
MEANING
ROUTED TO OUTPUT1 , Output n to input [x1]
ROUTED TO OUTPUT1 , Output n to input [x1] stands for Power On/Off
State of the output
Power Functions
Command: pwd
Response: PW stands for Power On/Off pwd
CMD: PWD
Important note control command:
Command is issued to the matrix will cause the response matrix once the command has been accepted and is finished. Make any order,
The response of the matrix must wait before sending another command. If you send another command before the completion of a matrix may be ignored.
Routing Functions
Command: swN M
Variations:
N: stands for Connect Output N
M:switch to input M
Response:
CMD: swN M
Response Example: sw1 a
CMD: sw1 A
Output 1, Select Input A sw2 b
CMD: sw2 B
Output 2, Select Input B
Special Commands
Command: ste
Response: OutputN M[STATE]
Variations:
N: Output N
M:Input M
[STATE]: [Signal] signal on from input
[Idle] no signal from input state of the output channel
STE
CMD: STATE
Output1 A[Idle]
Output2 A[Idle]
This product is to be free from defects in material and workmanship for the following limited warranty period:
Manufacturer will repair or replace the product only if the product has not been subjected to mechanical, electrical, or other forms of abuse or modification, and if the product fails and the manufacturer is notified within 1 year of purchase.
This warranty supersedes all other warranties expressed or implied, including without limitation, any implied warranty or merchantability or fitness for any particular purpose, all of which are expressly disclaimed.
The information in this manual has been carefully checked and is believed to be accurate; however, the manufacturer assumes no responsibility for any inaccuracies that may be contained in this manual. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. The technical information contained herein regarding HDMI 2x2 UTP Matrix Switch Extender with RS232 function over one Cat5e/6 features and specifications is subject to change without notice.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project