Sony KV-14LT1B CRT Television Instruction manual
Add to my manuals20 Pages
Sony KV-14LT1B is a powerful FD Trinitron Colour Television with a range of features to enhance your viewing experience. With its ability to receive both indoor and outdoor aerial signals, as well as connect to a VCR, you can enjoy a wide variety of programming options. The automatic tuning function makes it easy to find and store your favorite channels, while the teletext feature provides access to up-to-date news and information. Additionally, the TV boasts a range of picture and sound settings, allowing you to customize your viewing experience to suit your preferences.
advertisement
01GBCoverKV21;14LT1B.fm Page 1 Thursday, November 7, 2002 4:53 PM
R
4-205-481-
72
(1)
FD Trinitron
Colour Television
Instruction Manual
GB
KV-21LT1B
KV-14LT1B
© 2000 by Sony Corporation
02p2GBKV21;14LT1B.fm Page 2 Thursday, February 20, 2003 5:20 PM
NOTICE
A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or
BSI to BS 1362 (i.e. marked with or ) must be used.
When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
2
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace the fuse.
•
IMPORTANT
If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and an appropriate plug fitted in accordance with the following instructions:
The wires in this mains lead are coloured in accordance with the following code:
Blue Neutral
Brown Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol Y or coloured green or green and yellow.
WARNING
• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket outlet. This plug cannot be used and should be destroyed.
• To prevent fire or shock hazard, do not expose the unit to rain or moisture.
• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only.
03GBKV21;14LT1B.fm Page 3 Thursday, February 20, 2003 5:18 PM
Introduction
Thank you for choosing this Sony FD Trinitron Colour Television.
Before operating the TV, please read this manual thoroughly and retain it for future reference.
• Symbols used in the manual:
•
•
Informs you of possible hazards.
Important information
•
•
1,2...
Sequence of instructions.
•
•
K
MENU
Information on a feature.
Shaded buttons on the remote control show you the buttons you have to press to follow the sequence of the instructions.
Informs you of the result of instructions.
Table of Contents
Notice ........................................................................................................................................................ 2
Introduction.............................................................................................................................................. 3
Safety Information................................................................................................................................... 4
Overview
Overview of Remote Control Buttons .................................................................................................. 5
Overview of TV Buttons ........................................................................................................................ 6
Installation
Inserting Batteries into the Remote Control ........................................................................................ 6
Connecting an Indoor Aerial (only for KV-14LT1B) .......................................................................... 7
Connecting an Outdoor Aerial and VCR ............................................................................................ 7
First Time Operation
Switching On the TV and Automatically Tuning .............................................................................. 8
Menu system
Introducing and Using the Menu System.......................................................................................... 10
Menu Guide ........................................................................................................................................... 10
Teletext
............................................................................................................................................... 16
Additional Information
Connecting Optional Equipment ........................................................................................................ 17
Using Optional Equipment .................................................................................................................. 17
Specifications.......................................................................................................................................... 18
Troubleshooting..................................................................................................................................... 19
GB
Table of Contents
3
03GBKV21;14LT1B.fm Page 4 Thursday, February 20, 2003 5:18 PM
Safety Information
This set is to operate on a 220-
240V AC supply only. Take care not to connect too many appliances to the same power socket as this could result in fire or electric shock.
For environmental and safety reasons, it is recommended that the TV set is not left in standby mode when not in use. Disconnect from the mains.
Never push objects of any kind into the set as this could result in a fire or electric shock. Never spill liquid of any kind on the set. If any liquid or solid object does fall through, do not operate the TV. Have it checked immediately by qualified personnel.
Do not open the cabinet and the rear cover of the TV. Refer to qualified service personnel only.
For your own safety, do not touch any part of the TV, power lead or aerial lead during lightning storms.
To prevent fire or shock hazard, do not expose the TV to rain or moisture.
Do not cover the ventilation openings of the TV For ventilation, leave a space of at least 10cm all around the set.
Never place the TV in hot, humid or excessively dusty places. Do not install the TV where it may be exposed to mechanical vibrations.
To prevent fire, keep inflammable objects or naked lights (eg candles) away from the TV.
Clean the TV with a soft, lightly dampened cloth. Do not use benzine, thinner or any other chemicals to clean the TV. Do not scratch the TV screen. As a safety precaution, unplug the TV before cleaning it.
Pull out the power lead by the plug. Do not pull on the power lead itself.
Take care not to place heavy objects on the power lead as this could result in damage.
We recommend you wind any excess lead around the holders provided on the rear of the TV.
Place the TV on a secure stable stand. Do not allow children to climb on to it. Do not place the TV on its side or face up.
Unplug the power lead before moving the TV. Avoid uneven surfaces, quick steps or excessive force. If the set has been dropped or damaged, have it checked immediately by qualified service personnel.
Do not cover the ventilation openings of the TV with items such as curtains or newspapers etc.
4
Safety Information
03GBKV21;14LT1B.fm Page 5 Thursday, February 20, 2003 5:18 PM
Overview of Remote Control Buttons
Muting the Sound
Press to mute TV sound. press again to restore the sound.
Displaying on Screen information
Press to display all on-screen indications. Press again to cancel.
Selecting channels
Press to select channels.
For double-digit programme numbers, e.g. 23, press -/-- first, then the buttons 2 and 3.
If you enter an incorrect first digit, this should be corrected by entering another digit (0-9) and then selecting
-/-- button again to enter the programme number of your choice.
Selecting TV mode
Press to switch off teletext or video input.
Selecting Teletext
Press to switch on teletext.
This button only works in Teletext mode.
Function associated to this button does not work with this TV.
Selecting Picture mode
Press repeatedly to change the picture mode.
Adjusting TV volume
Press to adjust the volume of the TV.
This button only works in Teletext mode.
Function associated to this button does not work with this TV.
Selecting channels
Press to select the next or previous channel.
To Temporarily Switch Off TV
Press to temporarily switch off TV (the standby indicator on TV lights up). Press again to switch on
TV from standby mode.
1
4
7
2
5
8
0
K
S
3
6
9
MENU
PROGR
RM 887
To save energy we recommend switching off completely when TV is not in use.
After 15 minutes without a signal and without any button being pressed, the TV switches automatically into standby mode.
Selecting input source
Press repeatedly until the desired input symbol of the source appears on the TV screen.
Back to the channel last watched
Press to watch the last channel selected (watched for at least 5 seconds).
Displaying the menu system
Press to display the menu on the TV screen. Press again to remove the menu display from the TV screen.
Menu selection
•
When MENU is switched on:
Scroll Up
Scroll Down
Previous menu or selection
Next menu or selection
OK
confirms your selection
•
When MENU is switched off:
OK
Shows a channel overview.
Press or to select the channel and then, press again the
OK
button to watch the selected
channel.
Selecting Screen format
Press to view programmes in 16:9 mode. Press again to return to 4:3 mode.
GB
Besides TV functions, all coloured buttons as well as green symbols are also used for
Teletext operation. For more details, please refer to "“Teletext” section of this instruction manual.
Overview
5
03GBKV21;14LT1B.fm Page 6 Thursday, February 20, 2003 5:18 PM
Overview of TV Buttons
Auto Start
Up Button
Volume control buttons
Programme Up or
Down Buttons (Select
TV channels)
Press on the mark on the front of the TV to reveal the front connectors.
Selecting
Input source
Standby indicator
On/Off
switch
Video
Input jack
Audio
Input jack
Headphone jack
Inserting Batteries into the Remote Control
Make sure to insert the supplied batteries using the correct polarities.
Always remember you dispose of used batteries in an environmental friendly way.
6
Overview-Installation
03GBKV21;14LT1B.fm Page 7 Thursday, February 20, 2003 5:18 PM
Connecting an Indoor Aerial
(only for KV-14LT1B)
For a better reception we recommend you connect an external aerial. However, where an external aerial is not available and your local VHF/UHF signal is strong you can connect the supplied indoor aerial as follows:
1
Insert the aerial into the opening on top of the set until it clicks.
2
Connect the aerial connector to the aerial socket on the rear of the set.
3
After turning on the TV, adjust the aerial for optimum reception.
Connecting an Outdoor Aerial and VCR
Connecting cables are not supplied
GB
or
OUT IN
VCR
For more details of VCR connection, please refer to the section “Connecting Optional
Equipment” of this instruction manual.
Scart lead is optional.
Installation
7
03GBKV21;14LT1B.fm Page 8 Thursday, February 20, 2003 5:18 PM
Switching On the TV and Automatically Tuning
The first time you switch on your TV, a sequence of menu screen appear on the TV enabling you to: 1) choose the language of the menu screen, 2) choose the country in which you wish to operate the TV, 3) search and store all available channels (TV Broadcast) and 4) change the order in which the channels (TV Broadcast) appear on the screen.
However, if you need to change the language menu, change or repeat the tuning (e.g. when you move house) or rearrange again the order of the channels afterwards, you can do that by selecting the appropriate menu in the (Set Up). For more information, refer to the
“Menu Guide” section of this instruction manual. You can also do that by pressing the
Auto Start Up Button on the TV set.
1
Connect the TV plug to the mains socket (220-240V AC,
50Hz)
Press the on/off button on the TV set to turn on the TV.
The first time you press this button, a
Language
menu displays automatically on the TV screen.
2
Press the or button on the remote control to select the language, then press the
OK
button to confirm your selection. From now on all the menus will appear in the selected language.
Language
English
Español
Français
Italiano
Magyar
Nederlands
Select Language:
OK
3
The
Country
menu appears automatically on the TV screen. Press the or button to select the country in which you will operate the TV set, then press the
OK
button to confirm your selection.
If the country in which you want to use the TV set does not appear in the list, select “-” instead of a country.
Country
-
België/Belgique
France
Ireland
Luxembourg
Nederland
Select country:
OK
K
K
4
The Auto Tuning menu appears on the screen. Press the
OK
button to select
Yes
.
Do you want to start automatic tuning?
Yes
No
OK
K
continued...
8
First Time Operation
03GBKV21;14LT1B.fm Page 9 Thursday, February 20, 2003 5:18 PM
5
A new menu appears on the screen asking you to check that the aerial is connected. Ensure the aerial is connected and then press the
OK
button to start the automatic tuning.
The TV starts to automatically search and store all available channels (TV Broadcast) for you.
This procedure could take some minutes. Please be patient and do not press any button. Otherwise the automatic tuning will not be completed.
Please confirm that aerial is connected
Confirm
Searching...
OK
Auto Tuning
Programme: 01
System: B/G
Channel: C21
K
6
a)
After all available channels are captioned and stored, the
Programme Sorting
menu appears automatically on the screen enabling you to change the order in which the channels appear on the screen.
If you do not wish to change the channel order, go to step 7.
b)
If you wish to change the channel order:
1
Press the or button to select the programme number with the channel (TV Broadcast) you wish to rearrange, then press the button.
2
Press the or button to select the new programme number position for your selected channel (TV Broadcast), then press .
3
Repeat steps b)1 and b)2 if you wish to change the order of the other channels.
Programme Sorting
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
Select channel:
Exit:
MENU
OK
Programme Sorting
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58 05 C27
Select new position:
Exit:
MENU
OK
K
K
7
Press the
MENU
button to remove the menu from the
screen.
MENU
GB
Your TV is now ready for use
First Time Operation
9
03GBKV21;14LT1B.fm Page 10 Thursday, February 20, 2003 5:18 PM
Introducing and Using the Menu System
Your TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote Control to operate the menu system:
1
Press the MENU button to switch the first level menu on.
MENU
2
• To highlight the desired menu or option, press or
.
• To enter to the selected menu or option, press .
• To return to the last menu or option, press
.
• To alter settings of your selected option, press / / or .
• To confirm and store your selection, press OK.
3
Press the MENU button to remove the menu from the screen.
K
MENU
Menu Guide
Level 1 Level 2
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
OK
Level 3 / Function
PICTURE ADJUSTMENT
The “Picture Adjustment” menu allows you to alter the picture adjustments.
To do that: after selecting the item you want to alter press , then press repeatedly / / or to adjust it and finally press OK to store the new adjustment.
This menu also allows you to customise the picture mode based on the programme you are watching:
Personal (for individual settings).
Live (for live broadcast programmes).
Movie (for films).
• Brightness, Colour and Sharpness can only be alterated if “Personal” mode is selected.
• Hue is only available for NTSC colour signal (e.g: USA video tapes).
• Select Reset and press OK to reset the picture to the factory preset levels. continued...
10
Menu System
03GBKV21;14LT1B.fm Page 11 Thursday, February 20, 2003 5:18 PM
Level 1
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Timer
Sleep Timer: Off
On Timer: Off
OK
Level 2
Timer
Sleep Timer: Off
On Timer: i Off
OK
Level 3 / Function
SLEEP TIMER
The “Sleep Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically into the standby mode.
To do that: after selecting the option press , then press or to set the time period delay
(max. of 4 hours) and finally press OK to store.
• While watching the TV, you can press the
button on the remote control to display the
time remaining.
• One minute before the TV switches itself into
standby mode, the time remaining is displayed on
the TV screen automatically.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Timer
Sleep Timer: Off
On Timer: Off
OK
Timer
Sleep Timer: Off
On Timer: Off
OK
ON TIMER
The “On Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically on from standby mode.
To do that: after selecting the option press , then press or to set the time period delay
(max. 12 hours) and press OK to store. Finally press the standby button on the remote control. After the selected length of time the TV switches on automatically.
• The standby indicator on the TV set flashes
regularly to indicate that “On Timer” is active.
• Any loss of power will cause these settings to be
cleared.
GB
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
LANGUAGE / COUNTRY
The “Language/Country” option in the “Set
Up” menu allows you to select the language that the menus are displayed in. It also allows you to select the country in which you wish to operate the TV set.
To do that: after selecting the option, press and then proceed in the same way as in the steps 2 and 3 of the section “Switching On the
TV and Automatically Tuning”.
continued...
Menu System
11
03GBKV21;14LT1B.fm Page 12 Thursday, February 20, 2003 5:18 PM
Level 1
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
OK
Level 2
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Level 3 / Function
AUTO TUNING
The “Auto Tuning” option in the “Set Up” menu allows you to automatically search for and store all available TV channels.
To do that: after selecting the option, press and then proceed in the same way as in TV steps 4 and 5 of the section “Switching On the
TV and Automatically Tuning”.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
PROGRAMME SORTING
The “Programme Sorting” option in the “Set
Up” menu allows you to change the order in which the channels (TV Broadcast) appear on the screen.
To do that: after selecting the option, press and then proceed in the same way as in step 6 b) of the section “Switching On the TV and
Automatically Tuning”.
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Manual Programme Preset
Programme:
System:
Channel:
Label:
AFT:
Skip:
Decoder:
Confirm
01
B/G
C 21
--TVE
On
No
Off
OK
MANUAL PROGRAMME PRESET
The “Manual Programme Preset” option in the
“Set Up” menu allows you to:
a)
Preset channels or a video input source one
by one to the programme order of your
choice. To do that:
1 After selecting the ”Manual Programme
Preset” option, press then with
Programme
option highlighted press .
Press or to select on which programme number you want to preset the
channel (for VCR, select programme number
“0”). Then press .
2 After selecting the System option, press
.
Then press or to select the TV
Broadcast system (B/G for western European
countries, L for France, I for United
Kingdom or D/K for eastern European countries). Then press .
continued...
12
Menu System
03GBKV21;14LT1B.fm Page 13 Thursday, February 20, 2003 5:18 PM
Level 1
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Level 2
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Manual Programme Preset
Programme:
System:
Channel:
Label:
AFT:
Skip:
Decoder:
Confirm
01
B/G
C 21
--TVE
On
No
Off
OK
Level 3 / Function
3 After selecting the Channel option, press .
Then press or to select the channel tuning (“C” for terrestrial channels or “S” for cable channels). Next press . After that, press the number buttons to enter directly the channel number of the TV Broadcast or the channel of the VCR signal. If you do not know the channel number, press or to search for it. When you tune the desired channel, press OK twice to store.
Repeat all the above steps to tune and store more channels.
b)
Normally the automatic fine tuning (AFT) is operating, however you can manually fine tune the TV to obtain a better picture reception in the case that the picture is distorted.
To do that: while watching the channel (TV
Broadcast) you wish to fine tune, select the
AFT
option and press . Next press or to adjust the fine tuning between -15 and +15. Finally press OK twice to store.
c)
Skip any unwanted programme numbers when they are selected with the PROGR +/- buttons.
To do that: Highlighting the Programme
option, press the PROGR +/- button to select the programme number you want to skip.
When the programme you want to skip appears on the screen, select the Skip option and press . Next press or to select
Yes
. Finally press OK twice to confirm and store.
To cancel this function afterwards, select “No” instead of “Yes” in the step above.
d)
Label a channel using up to five characters.
To do that: Highlighting the Programme option, press the PROGR +/- button to select the programme number with the channel you wish to name. When the programme you want to name appears on the screen, select the Label option and press . Next press o r to select a letter, number or
“-“ for a blank. Press to confirm this character. Select the other four characters in the same way. After selecting all the characters, press OK twice to store.
continued...
Menu System
13
GB
03GBKV21;14LT1B.fm Page 14 Thursday, February 20, 2003 5:18 PM
Level 1
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Level 2
Advanced Features
Parental Lock:
Noise Reduction:
Auto Volume Ctrl.:
RGB Centring:
Picture Rotation:
Off
On
On
0
0
OK
Level 3 / Function
PARENTAL LOCK
The “Parental Lock” option in the “Advanced
Features” menu allows you to lock the buttons of the TV set. In this way after this option is selected and the TV set is switched off, the buttons on the TV do not work and the TV only works by using the remote control buttons.
To do that: after selecting the option, press .
Then press or to select On. Press OK to confirm and store and finally press on the remote control.
To cancel this function afterwards, select “Off” instead of “On” in the step above.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Advanced Features
Parental Lock:
Noise Reduction:
Auto Volume Ctrl.:
RGB Centring:
Picture Rotation:
Off
On
On
0
0
OK
NOISE REDUCTION
The “Noise Reduction” option in the
“Advanced Features” menu allows you to reduce the picture noise in case of a weak broadcasting signal.
To do that: after selecting the option, press .
Then press or to select On. Finally press
OK
to confirm and store.
To cancel this function afterwards, select “Off” instead of “On” in the step above.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Advanced Features
Parental Lock:
Noise Reduction:
Auto Volume Ctrl.:
RGB Centring:
Picture Rotation:
0
0
Off
On
On
OK
AUTO VOLUME CONTROL
The “Auto Volume Ctrl.” option in the
“Advanced Features” menu allows you to keep the same volume level of the channels, independent of the broadcast signal (e.g. in case of advertisement).
To do that: after selecting the option, press .
Then press o r to select On. Finally press
OK
to confirm and store.
To cancel this function afterwards, select “Off” instead of “On” in the step above.
continued...
14
Menu System
03GBKV21;14LT1B.fm Page 15 Thursday, February 20, 2003 5:18 PM
Level 1
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Level 2
Advanced Features
Parental Lock:
Noise Reduction:
Auto Volume Ctrl.:
RGB Centring:
Picture Rotation:
Off
On
On
0
0
OK
Level 3 / Function
RGB CENTRING
When connecting an RGB source, such as a
“PlayStation”, you may need to readjust the geometry of the picture. In that case, you can readjust it through the “RGB Centring” option in the “Advanced Features”.
To do that: while watching an RGB source select the “RGB Centring” option and press . Then press or to adjust the centre of the picture between –10 and +10. Finally press OK to confirm and store.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Manual Programme Preset
Advanced Features
OK
Advanced Features
Parental Lock:
Noise Reduction:
Auto Volume Ctrl.:
RGB Centring:
Picture Rotation:
Off
On
On
0
0
OK
PICTURE ROTATION
(only for KV-21LT1B)
Because of the earth’s magnetism, the picture might slant. In this case, you can correct the pictures slant by using the option “Picture
Rotation” in the “Advanced Features” menu.
To do that: after selecting the option, press .
Then press or to correct any slant of the picture between -5 and +5 and finally press OK to store.
GB
Menu System
15
03GBKV21;14LT1B.fm Page 16 Thursday, February 20, 2003 5:18 PM
Teletext
Teletext is an information service transmitted by most TV stations. The index page of the teletext service (usually page 100) gives you information on how to use the service. To operate teletext, use the remote control buttons as indicated below.
Make sure to use a channel (TV Broadcast) with a strong signal, otherwise teletext errors may occur.
To Switch On Teletext :
After select the channel (TV Broadcast) which carries the teletext you wish to view, press .
To Select a Teletext page:
Input 3 digits for the page number, using the numbered buttons.
• If you have made a mistake, retype the correct page number.
• If the counter on the screen continues searching, it is because this page is not available. In that case,
input another page number
To access the next or preceding page:
Press PROGR + ( ) or PROGR - ( ).
To superimpose teletext on to the TV:
Whilst you are viewing teletext, press . Press it again to cancel teletext mode.
To freeze a teletext page:
Some teletext pages have sub-pages which follow on automatically. To stop them, press
/ . Press it again to cancel the freeze.
To reveal concealed information (e.g: answer to a quiz):
Press / . Press it again to conceal the information.
To Switch Off Teletext:
Press .
Fastext
Fastext service lets you access pages with one button push.
While you are in Teletext mode and Fastext is broadcast, a colour coded menu appears at the bottom of the teletext page. Press the colour button (red, green, yellow or blue) to access the corresponding page.
16
Teletext
03GBKV21;14LT1B.fm Page 17 Thursday, February 20, 2003 5:18 PM
Connecting Optional Equipment
Using the following instructions, you can connect a wide range of optional equipment to your TV set. (Connecting cables are not supplied).
Connecting a VCR:
To connect a VCR, please refer to the section “Connecting the aerial and VCR” of this instruction manual. We recommend you connect your VCR using a scart lead. If you do not have a scart lead, tune in the VCR test signal to TV programme number “0”. by using “Manual Programme
Preset” option. (for details how to manual programme, see page
12, step a).
Also refer to your VCR instruction manual to find out how to find the output channel of your VCR.
A B
8mm/Hi8/DVC camcorder
1 2
“PlayStation”*
VCR
C
If you have connected a decoder to a VCR which supports
Decoder
Smartlink feature:
Select the “Manual Programme Preset” option in the “Set Up” menu and after entering in the
“Decoder” option, select “On” (by using or ) to each scrambled channel.
* “PlayStation”
is a product of Sony Computer Entertainment, Inc.
* “PlayStation” is a trademark of Sony Computer Entertainment, Inc.
Using Optional Equipment
1
Connect your equipment to the designated TV socket, as indicated above.
2
To watch the picture of the connected equipment, press the button repeatedly until the correct input symbol appears on the screen.
Symbol
1
Input Signals
• Audio / video input signal through the Scart connector C
• RGB input signal through the Scart connector C. This symbol appears only if a RGB source has been connected.
2 • Video input signal through the phono socket A and Audio input signal through B.
3
Switch on the connected equipment.
4
Press button on the remote control to return to the normal TV picture.
Additional Information
17
GB
03GBKV21;14LT1B.fm Page 18 Thursday, February 20, 2003 5:18 PM
Specifications
TV system:
B/G/H, L, I, D/K
Colour system:
PAL, SECAM
NTSC 3.58, 4.43 (only Video In)
Channel Coverage:
VHF: E2-E12
UHF: E21-E69
CATV: S1-S20
HYPER: S21-S41
L: F2-F10, B-Q, F21-F69
D/K: R1-R12, R21-R69
Picture Tube:
Flat Display FD Trinitron
Rear Terminals
:1/
21-pin scart connector
(CENELEC standard) including audio/video input, RGB input, TV audio/ video output.
Front Terminals
…2 video input – phono jack
2 audio input – phono jack
headphones jack
Sound Output:
• KV-21LT1B:
1 x 8 W (music power)
1 x 4 W (RMS Mono)
• KV-14LT1B:
1 x 6 W (music power)
1 x 3 W (RMS Mono)
Power Consumption:
• KV-21LT1B: 55 W
• KV-14LT1B: 42 W
Standby Power Consumption:
≤ 0.55 W
Dimensions (w x h x d) :
• KV-21LT1B: Approx. 514 x 478 x 487 mm.
• KV-14LT1B: Approx. 393 x 358 x 415 mm.
Weight:
• KV-21LT1B: Approx. 24 Kg.
• KV-14LT1B: Approx. 11.5 Kg.
Accessories supplied:
1 Remote Control (RM-887)
2 Batteries (IEC designated)
1 Aerial (only for KV-14LT1B)
Other features:
• Teletext, Fastext, TOPtext
• Sleep Timer
• Wake UP Timer
• Smartlink (direct link between your TV set
and a compatible VCR. For more information on Smartlink, please refer to
the Instruction Manual of your VCR).
• TV system Autodetection.
Design and specifications are subject to change without notice.
Ecological Paper- Totally Chlorine Free
18
Additional Information
03GBKV21;14LT1B.fm Page 19 Thursday, February 20, 2003 5:18 PM
Troubleshooting
Here are some simple solutions to the problems which may affect the picture and sound.
Problem
No picture (screen is dark) and no sound.
Poor or no picture (screen is dark), but good sound.
No picture or no menu information from the equipment connected to the
Scart connector.
Solution
• Check the aerial connection.
• Plug the TV in and press the button on the front of
TV.
• If the standby indicator is on, press button on
the remote control.
• Using the menu system, select the “Picture
Adjustment” menu and select “Reset” to return to the
factory settings.
• Check that the optional equipment is on and press the
button repeatedly on the remote control until the
correct input symbol is displayed on the screen.
Good picture, no sound.
• Press the +/- button on the remote control.
No colour on colour programmes.
Distorted picture when changing programmes or selecting teletext.
Wrong characters appear when viewing teletext.
Picture slanted
(only for KV-21LT1B)
Noisy picture when viewing a TV channel.
• Using the menu system, select the “Picture
Adjustment” menu and select “Reset” to return to factory settings.
• Turn off any equipment connected to the Scart
connector on the rear of the TV.
• Using the menu system, enter to the “Language/
Country” menu and select the country in which you operate the TV set. For Cyrillic languages, we recommend to select Russia country in the case that your own country does not appear in the list.
• Using the menu system, select the “Picture Rotation”
option in the “Advanced Features” menu to correct the
picture slant.
• Using the menu system, select the “Manual
Programme Preset” menu and adjust Fine Tuning
(AFT) to obtain better picture reception.
• Using the menu system, select the “Noise Reduction”
option in the “Advanced Features” menu and select
“On” to reduce the noise in the picture.
Remote control does not function.
• Replace the batteries.
The standby indicator on the TV flashes even though the “On Timer” function is not in use.
• Contact to your nearest Sony service centre.
In case of problems, have your TV serviced by qualified personnel. Never open the casing yourself.
GB
Additional Information
19
04B.cover.fm Page 1 Thursday, November 7, 2002 4:55 PM
Sony España, S.A.
Printed in Spain
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Notice
- 3 Introduction
- 4 Safety Information
- 5 Overview of Remote Control Buttons
- 6 Overview of TV Buttons
- 6 Inserting Batteries into the Remote Control
- 7 Connecting an Indoor Aerial (only for KV-14LT1B)
- 7 Connecting an Outdoor Aerial and VCR
- 8 Switching On the TV and Automatically Tuning
- 10 Introducing and Using the Menu System
- 10 Menu Guide
- 17 Connecting Optional Equipment
- 17 Using Optional Equipment
- 18 Specifications
- 19 Troubleshooting