IDatalink Econoline, Edge, Escape, Expedition, Explorer, F-150, Fiesta, Focus, Fusion, Mustang, Taurus, Transit Connect Maestro RR User manual
Anuncio
Anuncio
SELECT VEHICLE
PRINT PAGES NEEDED
1
HOW TO USE THIS INSTALL GUIDE
Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.
2
Print only the pages for your vehicle using the advanced options in the Print menu.
3
Install your Maestro RR according to the guide for your vehicle.
WARNING
Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.
INSTALL GUIDE
2008-2014
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD ECONOLINE 2008-2014
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD ECONOLINE 2008-2014
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD ECONOLINE 2008-2014
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD ECONOLINE 2008-2014
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD ECONOLINE 2008-2014
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
(DATA)
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Center dash, under the radio.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD ECONOLINE 2008-2014
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2007-2010
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD EDGE 2007-2010
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD EDGE 2007-2010
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD EDGE 2007-2010
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD EDGE 2007-2010
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD EDGE 2007-2010
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD EDGE 2007-2010
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2008-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD ESCApE 2008-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD ESCApE 2008-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD ESCApE 2008-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD ESCApE 2008-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD ESCApE 2008-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
(DATA)
(DATA)
(MUX)
Polarity
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Junction connector, behind the radio to the right.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD ESCApE 2008-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2007-2014
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD ExpEDITION 2007-2014
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD ExpEDITION 2007-2014
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD ExpEDITION 2007-2014
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD ExpEDITION 2007-2014
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD ExpEDITION 2007-2014
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD ExpEDITION 2007-2014
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2006-2010
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD ExpLORER 2006-2010
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD ExpLORER 2006-2010
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD ExpLORER 2006-2010
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD ExpLORER 2006-2010
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD ExpLORER 2006-2010
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
White/Brown
Polarity
(DATA)
(DATA)
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Center console, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD ExpLORER 2006-2010
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2006-2010
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD ExpLORER SpORT TRAC 2006-2010
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD ExpLORER SpORT TRAC 2006-2010
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD ExpLORER SpORT TRAC 2006-2010
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD ExpLORER SpORT TRAC 2006-2010
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD ExpLORER SpORT TRAC 2006-2010
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
White/Brown
Polarity
(DATA)
(DATA)
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Center console, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD ExpLORER SpORT TRAC 2006-2010
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2008-2010
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD F-SERIES SUpER DUTY 2008-2010
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD F-SERIES SUpER DUTY 2008-2010
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD F-SERIES SUpER DUTY 2008-2010
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD F-SERIES SUpER DUTY 2008-2010
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD F-SERIES SUpER DUTY 2008-2010
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
(DATA)
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Passenger side, next to glove box.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD F-SERIES SUpER DUTY 2008-2010
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2011-2016
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD F-SERIES SUpER DUTY 2011-2016
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD F-SERIES SUpER DUTY 2011-2016
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
• Remove the factory radio.
STEP 2
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 3
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 5
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD F-SERIES SUpER DUTY 2011-2016
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD F-SERIES SUpER DUTY 2011-2016
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 4
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
STEP 2
FACTORY RADIO HARNESS
FO1 T-HARNESS
STEP 3
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
WIRES FROM
VEHICLE
STEP 5
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
3 maestro.idatalink.com
5
FORD F-SERIES SUpER DUTY 2011-2016
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
Polarity
(DATA)
(DATA)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD F-SERIES SUpER DUTY 2011-2016
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2009-2010
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD F150 2009-2010
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD F150 2009-2010
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD F150 2009-2010
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD F150 2009-2010
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD F150 2009-2010
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
(DATA)
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Center dash, under the tray.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD F150 2009-2010
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2011-2014
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD F150 2011-2014
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD F150 2011-2014
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
• Remove the factory radio.
STEP 2
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 3
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 5
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD F150 2011-2014
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD F150 2011-2014
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 4
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
STEP 2
FACTORY RADIO HARNESS
FO1 T-HARNESS
STEP 3
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
WIRES FROM
VEHICLE
STEP 5
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
3 maestro.idatalink.com
5
FORD F150 2011-2014
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
Polarity
(DATA)
(DATA)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD F150 2011-2014
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2006-2007
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD FIVE HUNDRED 2006-2007
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD FIVE HUNDRED 2006-2007
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
• Remove the factory radio.
STEP 2
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 3
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 5
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD FIVE HUNDRED 2006-2007
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD FIVE HUNDRED 2006-2007
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 4
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
STEP 2
FACTORY RADIO HARNESS
FO1 T-HARNESS
STEP 3
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
WIRES FROM
VEHICLE
STEP 5
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
3 maestro.idatalink.com
5
FORD FIVE HUNDRED 2006-2007
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
Polarity
(DATA)
(DATA)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD FIVE HUNDRED 2006-2007
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2009-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD FLEx 2009-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD FLEx 2009-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD FLEx 2009-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD FLEx 2009-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD FLEx 2009-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, junctionconnector, in front of the shifter.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD FLEx 2009-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2008-2011
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD FOCUS 2008-2011
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD FOCUS 2008-2011
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD FOCUS 2008-2011
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD FOCUS 2008-2011
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD FOCUS 2008-2011
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, horizontal harness on the heater box.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD FOCUS 2008-2011
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2006-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD FUSION 2006-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD FUSION 2006-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD FUSION 2006-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD FUSION 2006-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD FUSION 2006-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA)
(MUX)
OBDII connector, under driver side dash
Center console, right side, in front of the arm rest.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD FUSION 2006-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2007-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD MUSTANG 2007-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD MUSTANG 2007-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD MUSTANG 2007-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD MUSTANG 2007-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD MUSTANG 2007-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Polarity
(DATA)
Can2L OBDII ~ 16 pin 14 White (DATA)
SWI 2 ~ ~ ~ ~ Blue/Orange or Blue
SWI 2 connection is required only if vehicle is equipped with Sync.
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Sync unit, behind the glove box.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD MUSTANG 2007-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
BASE 2013-2014
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD MUSTANG BASE 2013-2014
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD MUSTANG BASE 2013-2014
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD MUSTANG BASE 2013-2014
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD MUSTANG BASE 2013-2014
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD MUSTANG BASE 2013-2014
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Polarity
(DATA)
Can2L OBDII ~ 16 pin 14 White (DATA)
SWI 2 ~ ~ ~ ~ Blue/Orange or Blue
SWI 2 connection is required only if vehicle is equipped with Sync.
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Sync unit, behind the glove box.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD MUSTANG BASE 2013-2014
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
ShAkER 2013-2014
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD MUSTANG SHAkER 2013-2014
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD MUSTANG SHAkER 2013-2014
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
2
ADS-RR(SR)-FOR01-DS2
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD MUSTANG SHAkER 2013-2014
Automotive Data Solutions Inc. © 2015
2
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD MUSTANG SHAkER 2013-2014
WIRING DIAGRAM
STEP 1
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
GREEN
GREEN/BLACK
PURPLE
PURPLE/BLACK
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
LF RCA INPUT
RF RCA INPUT
LR RCA INPUT
RR RCA INPUT
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 5
RCA CABLES
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
2 maestro.idatalink.com
5
FORD MUSTANG SHAkER 2013-2014
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Polarity
(DATA)
Can2L OBDII ~ 16 pin 14 White (DATA)
SWI 2 ~ ~ ~ ~ Blue/Orange or Blue
SWI 2 connection is required only if vehicle is equipped with Sync.
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Sync unit, behind the glove box.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD MUSTANG SHAkER 2013-2014
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
ShAkER PRO 2013-2014
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD MUSTANG SHAkER pRO 2013-2014
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD MUSTANG SHAkER pRO 2013-2014
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
2
ADS-RR(SR)-FOR01-DS2
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD MUSTANG SHAkER pRO 2013-2014
Automotive Data Solutions Inc. © 2015
2
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD MUSTANG SHAkER pRO 2013-2014
WIRING DIAGRAM
STEP 1
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
GREEN
GREEN/BLACK
PURPLE
PURPLE/BLACK
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
LF RCA INPUT
RF RCA INPUT
LR RCA INPUT
RR RCA INPUT
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 5
RCA CABLES
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
2 maestro.idatalink.com
5
FORD MUSTANG SHAkER pRO 2013-2014
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Polarity
(DATA)
Can2L OBDII ~ 16 pin 14 White (DATA)
SWI 2 ~ ~ ~ ~ Blue/Orange or Blue
SWI 2 connection is required only if vehicle is equipped with Sync.
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Sync unit, behind the glove box.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD MUSTANG SHAkER pRO 2013-2014
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2008-2009
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD TAURUS 2008-2009
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD TAURUS 2008-2009
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD TAURUS 2008-2009
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD TAURUS 2008-2009
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD TAURUS 2008-2009
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Gray/Blue
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD TAURUS 2008-2009
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2010-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD TAURUS 2010-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD TAURUS 2010-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD TAURUS 2010-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD TAURUS 2010-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD TAURUS 2010-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD TAURUS 2010-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2008-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
FORD TAURUS x 2008-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
FORD TAURUS x 2008-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
FORD TAURUS x 2008-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
FORD TAURUS x 2008-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
FORD TAURUS x 2008-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
FORD TAURUS x 2008-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2009-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
LINCOLN MkS 2009-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
LINCOLN MkS 2009-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
LINCOLN MkS 2009-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
LINCOLN MkS 2009-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
LINCOLN MkS 2009-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
LINCOLN MkS 2009-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2010-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
LINCOLN MkT 2010-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
LINCOLN MkT 2010-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
LINCOLN MkT 2010-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
LINCOLN MkT 2010-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
LINCOLN MkT 2010-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
LINCOLN MkT 2010-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2007-2010
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
LINCOLN Mkx 2007-2010
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
LINCOLN Mkx 2007-2010
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
LINCOLN Mkx 2007-2010
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
LINCOLN Mkx 2007-2010
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
LINCOLN Mkx 2007-2010
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
LINCOLN Mkx 2007-2010
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2007-2012
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
LINCOLN MkZ 2007-2012
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
LINCOLN MkZ 2007-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
LINCOLN MkZ 2007-2012
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
LINCOLN MkZ 2007-2012
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
LINCOLN MkZ 2007-2012
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
LINCOLN MkZ 2007-2012
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2007-2014
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
LINCOLN NAVIGATOR 2007-2014
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
LINCOLN NAVIGATOR 2007-2014
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
LINCOLN NAVIGATOR 2007-2014
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
LINCOLN NAVIGATOR 2007-2014
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
LINCOLN NAVIGATOR 2007-2014
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
(DATA)
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Sync unit, center console.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
LINCOLN NAVIGATOR 2007-2014
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2006
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
LINCOLN ZEpHYR 2006
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
LINCOLN ZEpHYR 2006
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
• Remove the factory radio.
STEP 2
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 3
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 5
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
LINCOLN ZEpHYR 2006
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
LINCOLN ZEpHYR 2006
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 4
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
STEP 2
FACTORY RADIO HARNESS
FO1 T-HARNESS
STEP 3
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
WIRES FROM
VEHICLE
STEP 5
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
3 maestro.idatalink.com
5
LINCOLN ZEpHYR 2006
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
Polarity
(DATA)
(DATA)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
LINCOLN ZEpHYR 2006
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2008-2011
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
MAZDA TRIBUTE 2008-2011
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
MAZDA TRIBUTE 2008-2011
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
• Remove the factory radio.
STEP 2
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 3
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 5
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
MAZDA TRIBUTE 2008-2011
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
MAZDA TRIBUTE 2008-2011
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 4
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
STEP 2
FACTORY RADIO HARNESS
FO1 T-HARNESS
STEP 3
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
WIRES FROM
VEHICLE
STEP 5
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
3 maestro.idatalink.com
5
MAZDA TRIBUTE 2008-2011
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
Polarity
(DATA)
(DATA)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
MAZDA TRIBUTE 2008-2011
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2008-2011
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
MERCURY MARINER 2008-2011
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
MERCURY MARINER 2008-2011
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
MERCURY MARINER 2008-2011
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
MERCURY MARINER 2008-2011
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
MERCURY MARINER 2008-2011
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
(DATA)
(DATA)
(MUX)
Polarity
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Junction connector, behind the radio to the right.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
MERCURY MARINER 2008-2011
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2006-2011
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
MERCURY MILAN 2006-2011
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
MERCURY MILAN 2006-2011
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
MERCURY MILAN 2006-2011
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
MERCURY MILAN 2006-2011
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
MERCURY MILAN 2006-2011
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Blue/Orange
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA)
(MUX)
OBDII connector, under driver side dash
Center console, right side, in front of the arm rest.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
MERCURY MILAN 2006-2011
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2005-2007
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
MERCURY MONTEGO 2005-2007
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
MERCURY MONTEGO 2005-2007
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
• Remove the factory radio.
STEP 2
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 3
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 5
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
MERCURY MONTEGO 2005-2007
Automotive Data Solutions Inc. © 2015
3
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
MERCURY MONTEGO 2005-2007
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 4
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
STEP 2
FACTORY RADIO HARNESS
FO1 T-HARNESS
STEP 3
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
WIRES FROM
VEHICLE
STEP 5
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
3 maestro.idatalink.com
5
MERCURY MONTEGO 2005-2007
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
Polarity
(DATA)
(DATA)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
MERCURY MONTEGO 2005-2007
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2006-2010
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
MERCURY MOUNTAINEER 2006-2010
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
MERCURY MOUNTAINEER 2006-2010
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
MERCURY MOUNTAINEER 2006-2010
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
MERCURY MOUNTAINEER 2006-2010
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
MERCURY MOUNTAINEER 2006-2010
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
White/Brown
Polarity
(DATA)
(DATA)
(MUX)
Wire
Location
OBDII connector, under driver side dash
OBDII connector, under driver side dash
Center console, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
MERCURY MOUNTAINEER 2006-2010
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
INSTALL GUIDE
2008-2009
RETAINS STEERING WHEEL CONTROLS SYNC VOICE COMMANDS, SYNC BLUETOOTH,
SIRIUS SATELLITE AND MORE!
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro FO1 Installation Harness
OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink
Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions
Wiring Diagram
Vehicle Wire Reference Chart
Radio Wire Reference Chart
MERCURY SABLE 2008-2009
6
7
3
5
NEED hELP?
1 866 427-2999 [email protected]
maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
2
MERCURY SABLE 2008-2009
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness and match the wire colors.
• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
NOTE:
In Pioneer radios: plug Audio cable in auxiliary input of the radio.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.
STEP 4
• Access the OBDII connector located under the driver side dashboard.
• Connect the RED/BROWN wire of FO1 T-harness to WHITE/
BLUE wire of the OBDII connector located at pin 6.
• Connect the YELLOW/BROWN wire of FO1 T-harness to the
WHITE wire of the OBDII connector located at pin 14.
NOTE:
Connections not required for 2014-2015 Pioneer radios.
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2
MODULE PROGRAMMING
• Open the vehicle driver door, insert the key into the ignition and turn it to the ACC position.
• The OEM Bluetooth is OFF by default. To activate it, go to the radio screen, scroll down to FORD SETUP, press SET, go to the OEM Bluetooth and press ON, then Press the
BACK button (circular shaped arrow).
• Scroll down, press FINISH and wait. Press START, then press NEXT.
• Now follow the radio screen instructions while performing the following steps: Turn the key to the OFF position, then to the ACC position, turn it back to the OFF position, then to the ACC position.
The module is now programmed and ready to be used. To access the new menus, press on FORD FEATURES.
• Test all the functionalities then reassemble the dashboard carefully.
maestro.idatalink.com
3
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
MERCURY SABLE 2008-2009
Automotive Data Solutions Inc. © 2015
1
ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
4
MERCURY SABLE 2008-2009
WIRING DIAGRAM
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
BROWN (NOT CONNECTED)
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
STEP 2
PINK/RED - SWI 2 (-) INPUT
STEERING
WHEEL SIDE
REFER TO WIRE CHART
FOR WIRE LOCATION
STEP 3
SYNC HARNESS
INSULATE
WIRE
SYNC
MODULE SIDE
FACTORY RADIO HARNESS
STEP 5
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
SUB IN
CENTER IN
RCA CABLES
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
DATA
CABLE
AUDIO
CABLE
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEP 4
RED/BROWN - CAN2H
OBDII CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
YELLOW/BROWN - CAN2L
NOTE: PIN SIDE VIEW.
CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2
STEP 6
A
C
F
G
A
C
MAESTRO RR MODULE
H
G
F
D
H
D
1 maestro.idatalink.com
5
MERCURY SABLE 2008-2009
VEHICLE WIRE REFERENCE CHART
Wire
Description
Connector
Name
Connector
Color
Connector
Type
Position Wire Color
Can2H OBDII ~ 16 pin 06 White/Blue
Can2L OBDII ~ 16 pin 14 White
SWI 2 ~ ~ ~ ~
SWI 2 connection is required only if vehicle is equipped with Sync.
Gray/Blue
Polarity
(DATA)
Wire
Location
OBDII connector, under driver side dash
(DATA) OBDII connector, under driver side dash
(MUX) Center console, right side, harness going to the back.
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
6
MERCURY SABLE 2008-2009
RADIO WIRE REFERENCE CHART
Wire
Description
Polarity
Wire Color on Maestro
T-Harness
Illumination
Reverse Light
E-Brake
Foot Brake (+)
VSS (vehicle speed sensor) (DATA)
(+)
(+)
(-)
Orange
Purple/White
Lt Green
Yellow/Black
Pink
Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
N/A
Orange/White
Yellow/Blue
Yellow/Black
Green/White
Orange/White
Purple/White
Lt Green
N/A
N/A
Orange/White
Purple/White
Lt Green
N/A
Pink
Automotive Data Solutions Inc. © 2015 ADS-RR(SR)-FOR01-DS2 maestro.idatalink.com
7
Descargar
Enlace público actualizado
Se ha actualizado el enlace público a tu chat. Puedes ver y gestionar tus enlaces de chat después del registro aquí.
Enlace público del documento
Anuncio
