iDataLink Maestro RR Install Manual

SELECT VEHICLE

PRINT PAGES NEEDED

1

HOW TO USE THIS INSTALL GUIDE

Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

2 Print only the pages for your vehicle using the advanced options in the Print menu.

3

Install your Maestro RR according to the guide for your vehicle.

WARNING

Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.

INSTALL GUIDE

2008-2014

Ford EconolinE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford EconolinE 2008-2014

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford EconolinE 2008-2014

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford EconolinE 2008-2014

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER DASH, UNDER THE RADIO

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford EconolinE 2008-2014

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford EconolinE 2008-2014

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2007-2010

Ford EdgE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford EdgE 2007-2010

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford EdgE 2007-2010

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford EdgE 2007-2010

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford EdgE 2007-2010

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford EdgE 2007-2010

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2008-2012

Ford EscapE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford EscapE 2008-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford EscapE 2008-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford EscapE 2008-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

JUNCTION CONNECTOR, BEHIND THE RADIO TO THE RIGHT

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford EscapE 2008-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford EscapE 2008-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2007-2014

Ford ExpEdition

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford ExpEdition 2007-2014

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford ExpEdition 2007-2014

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford ExpEdition 2007-2014

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford ExpEdition 2007-2014

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford ExpEdition 2007-2014

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2006-2010

Ford ExplorEr

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford ExplorEr 2006-2010

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford ExplorEr 2006-2010

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford ExplorEr 2006-2010

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : WHITE/BROWN

CENTER CONSOLE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford ExplorEr 2006-2010

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford ExplorEr 2006-2010

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2006-2010

Ford ExplorEr sport trac

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford ExplorEr sport trac 2006-2010

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford ExplorEr sport trac 2006-2010

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford ExplorEr sport trac 2006-2010

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : WHITE/BROWN

CENTER CONSOLE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford ExplorEr sport trac 2006-2010

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford ExplorEr sport trac 2006-2010

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2008-2010

Ford F-sEriEs supEr duty

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford F-sEriEs supEr duty 2008-2010

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford F-sEriEs supEr duty 2008-2010

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford F-sEriEs supEr duty 2008-2010

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

PASSENGER SIDE, NEXT TO GLOVE BOX

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford F-sEriEs supEr duty 2008-2010

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford F-sEriEs supEr duty 2008-2010

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2011-2016

Ford F-sEriEs supEr duty

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford F-sEriEs supEr duty 2011-2016

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford F-sEriEs supEr duty 2011-2016

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

• Remove the factory radio.

STEP 2

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

3

ADS-RR(SR)-FOR01-DS-IG-EN Automotive Data Solutions Inc. © 2019

STEP 5

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford F-sEriEs supEr duty 2011-2016

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

STEP 4

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 3

OBDII CONNECTOR

STEP 5

PINK/RED (NC)

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

MAESTRO RR MODULE

3 maestro.idatalink.com

4

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

Ford F-sEriEs supEr duty 2011-2016

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford F-sEriEs supEr duty 2011-2016

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2009-2010

Ford F150

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford F150 2009-2010

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford F150 2009-2010

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford F150 2009-2010

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER DASH, UNDER THE TRAY

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford F150 2009-2010

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford F150 2009-2010

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2011-2014

Ford F150

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford F150 2011-2014

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford F150 2011-2014

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

• Remove the factory radio.

STEP 2

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

3

ADS-RR(SR)-FOR01-DS-IG-EN Automotive Data Solutions Inc. © 2019

STEP 5

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford F150 2011-2014

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

STEP 4

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 3

OBDII CONNECTOR

STEP 5

PINK/RED (NC)

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

MAESTRO RR MODULE

3 maestro.idatalink.com

4

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

Ford F150 2011-2014

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford F150 2011-2014

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2006-2007

Ford FivE hundrEd

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford FivE hundrEd 2006-2007

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford FivE hundrEd 2006-2007

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

• Remove the factory radio.

STEP 2

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

3

ADS-RR(SR)-FOR01-DS-IG-EN Automotive Data Solutions Inc. © 2019

STEP 5

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford FivE hundrEd 2006-2007

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

STEP 4

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 3

OBDII CONNECTOR

STEP 5

PINK/RED (NC)

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

MAESTRO RR MODULE

3 maestro.idatalink.com

4

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

Ford FivE hundrEd 2006-2007

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford FivE hundrEd 2006-2007

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2009-2012

Ford FlEx

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford FlEx 2009-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford FlEx 2009-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford FlEx 2009-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, JUNCTION CONNECTOR, IN FRONT OF THE SHIFTER

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford FlEx 2009-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford FlEx 2009-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2008-2011

Ford Focus

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford Focus 2008-2011

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford Focus 2008-2011

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford Focus 2008-2011

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, HORIZONTAL HARNESS ON THE HEATER BOX

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford Focus 2008-2011

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford Focus 2008-2011

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2006-2012

Ford Fusion

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford Fusion 2006-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford Fusion 2006-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford Fusion 2006-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, IN FRONT OF THE ARM REST

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford Fusion 2006-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford Fusion 2006-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2007-2012

Ford Mustang

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford Mustang 2007-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford Mustang 2007-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford Mustang 2007-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE OR BLUE

SYNC UNIT, BEHIND THE GLOVE BOX

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford Mustang 2007-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford Mustang 2007-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2013-2014

Ford Mustang

BasE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford Mustang BasE 2013-2014

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford Mustang BasE 2013-2014

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford Mustang BasE 2013-2014

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE OR BLUE

SYNC UNIT, BEHIND THE GLOVE BOX

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford Mustang BasE 2013-2014

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford Mustang BasE 2013-2014

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2013-2014

Ford Mustang shakEr

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford Mustang shakEr 2013-2014

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford Mustang shakEr 2013-2014

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Automotive Data Solutions Inc. © 2019

2

ADS-RR(SR)-FOR01-DS-IG-EN

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford Mustang shakEr 2013-2014

WIRING DIAGRAM

STEP 1

WHITE

WHITE/BLACK

GRAY

GRAY/BLACK

GREEN

GREEN/BLACK

PURPLE

PURPLE/BLACK

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

LF RCA INPUT

RF RCA INPUT

LR RCA INPUT

RR RCA INPUT

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 5

RCA CABLES

PIONEER RADIO:

ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE OR BLUE

SYNC UNIT, BEHIND THE GLOVE BOX

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

CONNECT TO

AFTERMARKET RADIO

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

STEP 4

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

2 maestro.idatalink.com

4

Ford Mustang shakEr 2013-2014

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford Mustang shakEr 2013-2014

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2013-2014

Ford Mustang shakEr pro

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford Mustang shakEr pro 2013-2014

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford Mustang shakEr pro 2013-2014

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Automotive Data Solutions Inc. © 2019

2

ADS-RR(SR)-FOR01-DS-IG-EN

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford Mustang shakEr pro 2013-2014

WIRING DIAGRAM

STEP 1

WHITE

WHITE/BLACK

GRAY

GRAY/BLACK

GREEN

GREEN/BLACK

PURPLE

PURPLE/BLACK

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

LF RCA INPUT

RF RCA INPUT

LR RCA INPUT

RR RCA INPUT

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 5

RCA CABLES

PIONEER RADIO:

ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE OR BLUE

SYNC UNIT, BEHIND THE GLOVE BOX

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

CONNECT TO

AFTERMARKET RADIO

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

STEP 4

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

2 maestro.idatalink.com

4

Ford Mustang shakEr pro 2013-2014

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford Mustang shakEr pro 2013-2014

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2008-2009

Ford taurus

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford taurus 2008-2009

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford taurus 2008-2009

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford taurus 2008-2009

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : GRAY/BLUE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford taurus 2008-2009

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford taurus 2008-2009

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2010-2012

Ford taurus

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford taurus 2010-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford taurus 2010-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford taurus 2010-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford taurus 2010-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford taurus 2010-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2008-2012

Ford taurus x

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

Ford taurus x 2008-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

Ford taurus x 2008-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

Ford taurus x 2008-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

Ford taurus x 2008-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

Ford taurus x 2008-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2009-2012 lincoln Mks

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table lincoln Mks 2009-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

lincoln Mks 2009-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

lincoln Mks 2009-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

lincoln Mks 2009-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

lincoln Mks 2009-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2010-2012 lincoln Mkt

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table lincoln Mkt 2010-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

lincoln Mkt 2010-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

lincoln Mkt 2010-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

lincoln Mkt 2010-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

lincoln Mkt 2010-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2007-2010 lincoln Mkx

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table lincoln Mkx 2007-2010

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

lincoln Mkx 2007-2010

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

lincoln Mkx 2007-2010

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

lincoln Mkx 2007-2010

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

lincoln Mkx 2007-2010

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2007-2012 lincoln MkZ

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table lincoln MkZ 2007-2012

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

lincoln MkZ 2007-2012

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

lincoln MkZ 2007-2012

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

lincoln MkZ 2007-2012

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

lincoln MkZ 2007-2012

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2007-2014 lincoln navigator

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table lincoln navigator 2007-2014

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

lincoln navigator 2007-2014

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

lincoln navigator 2007-2014

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

SYNC UNIT, CENTER CONSOLE

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

lincoln navigator 2007-2014

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

lincoln navigator 2007-2014

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2006 lincoln ZEphyr

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table lincoln ZEphyr 2006

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

lincoln ZEphyr 2006

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

• Remove the factory radio.

STEP 2

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

3

ADS-RR(SR)-FOR01-DS-IG-EN Automotive Data Solutions Inc. © 2019

STEP 5

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

lincoln ZEphyr 2006

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

STEP 4

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 3

OBDII CONNECTOR

STEP 5

PINK/RED (NC)

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

MAESTRO RR MODULE

3 maestro.idatalink.com

4

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

lincoln ZEphyr 2006

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

lincoln ZEphyr 2006

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2008-2011

MaZda triButE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

MaZda triButE 2008-2011

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

MaZda triButE 2008-2011

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

• Remove the factory radio.

STEP 2

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

3

ADS-RR(SR)-FOR01-DS-IG-EN Automotive Data Solutions Inc. © 2019

STEP 5

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

MaZda triButE 2008-2011

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

STEP 4

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 3

OBDII CONNECTOR

STEP 5

PINK/RED (NC)

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

MAESTRO RR MODULE

3 maestro.idatalink.com

4

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

MaZda triButE 2008-2011

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

MaZda triButE 2008-2011

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2008-2011

MErcury MarinEr

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

MErcury MarinEr 2008-2011

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

MErcury MarinEr 2008-2011

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

MErcury MarinEr 2008-2011

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

JUNCTION CONNECTOR, BEHIND THE RADIO TO THE RIGHT

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

MErcury MarinEr 2008-2011

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

MErcury MarinEr 2008-2011

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2006-2011

MErcury Milan

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

MErcury Milan 2006-2011

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

MErcury Milan 2006-2011

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

MErcury Milan 2006-2011

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : BLUE/ORANGE

CENTER CONSOLE, RIGHT SIDE, IN FRONT OF ARM REST

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

MErcury Milan 2006-2011

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

MErcury Milan 2006-2011

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2005-2007

MErcury MontEgo

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

MErcury MontEgo 2005-2007

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

MErcury MontEgo 2005-2007

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

• Remove the factory radio.

STEP 2

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

3

ADS-RR(SR)-FOR01-DS-IG-EN Automotive Data Solutions Inc. © 2019

STEP 5

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

MErcury MontEgo 2005-2007

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

STEP 4

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 3

OBDII CONNECTOR

STEP 5

PINK/RED (NC)

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

MAESTRO RR MODULE

3 maestro.idatalink.com

4

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

MErcury MontEgo 2005-2007

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

MErcury MontEgo 2005-2007

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2006-2010

MErcury MountainEEr

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

MErcury MountainEEr 2006-2010

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

MErcury MountainEEr 2006-2010

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

MErcury MountainEEr 2006-2010

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : WHITE/BROWN

CENTER CONSOLE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

MErcury MountainEEr 2006-2010

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

MErcury MountainEEr 2006-2010

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

INSTALL GUIDE

2008-2009

MErcury saBlE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

OR

PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES

E L E C T R O N I C S

Click here for:

Radar Installation Guides

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.

Before starting your installation, please ensure that your iDatalink

Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions

Wiring Diagram

Radio Wire Reference Chart

Troubleshooting Table

MErcury saBlE 2008-2009

5

6

3

4

NEED HELP?

1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

2

MErcury saBlE 2008-2009

INSTALLATION INSTRUCTIONS

STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.

Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors.

(Refer to Diagram)

STEP 2

Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the

BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2

INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3

• Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5

• Plug the aftermarket radio harnesses into the aftermarket radio.

• Plug the Data cable to the data port of the aftermarket radio.

Automotive Data Solutions Inc. © 2019

1

ADS-RR(SR)-FOR01-DS-IG-EN

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6

• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

maestro.idatalink.com

3

MErcury saBlE 2008-2009

WIRING DIAGRAM

STEP 1

CUT AND REMOVE

THE SPEAKER WIRE

JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE - RR SPEAKER (+)

PURPLE/BLACK - RR SPEAKER (-)

BLUE/WHITE - AMP. TURN ON (+)

BLACK - GROUND

RED - ACCESSORY (+)

YELLOW - 12V (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+)

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

YELLOW/BLACK - FOOT BRAKE

BROWN (NOT CONNECTED)

STEP 5

PIONEER RADIO: ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

MAIN

HARNESS

CONNECT TO

AFTERMARKET RADIO

SEE RADIO WIRE

REFERENCE

CHART

FOR RADIO WIRE

COLORS

STEP 2

PINK/RED - SWI 2 (-) INPUT

STEERING

WHEEL SIDE

SYNC HARNESS

INSULATE

WIRE

SYNC

MODULE SIDE

SWI 2 : GRAY/BLUE

CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3

FACTORY RADIO HARNESS

SUB IN

CENTER IN

RCA CABLES

CONNECT AUX IN

ONLY IF YOU DON’T HAVE SYNC

DATA

CABLE

AUDIO

CABLE

WIRES FROM

VEHICLE

STEP 4

OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN

1 maestro.idatalink.com

4

MErcury saBlE 2008-2009

RADIO WIRE REFERENCE CHART

Wire

Description

Polarity

Wire Color on Maestro

T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable

Wire Color on Pioneer cable

Wire Color on Sony cable

Illumination

Reverse Light

E-Brake

Foot Brake (+)

VSS (vehicle speed sensor) (DATA)

(+)

(+)

(-)

Orange

Purple/White

Lt Green

Yellow/Black

Pink

N/A

Orange/White

Yellow/Blue

Yellow/Black

Green/White

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange/White

Purple/White

Lt Green

N⁄A

Pink

Orange

Purple/White

Lt Green

N/A

N/A

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.com

5

MErcury saBlE 2008-2009

TROUBLESHOOTING TABLE

PROBLEM

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

There is no sound from Sync (if equipped).

The radio will not turn on, and there was no 16-pin plug connected to the

OEM radio.

The light on the Maestro is fl ashing

The light on the Maestro is blinking

RED ONCE

RED TWICE

.

.

SOLUTION

Ensure OBDII connector is securely attached to the OBDII connector of the vehicle.

If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/

BROWN wire is connected to PIN 14 of the OBDII connector. Do not use

T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

Ensure the all black, 3-pin to 3.5mm audio cable is connected between the

RR and the radio. Make sure it is in the correct radio input.

The data lines are not present behind the radio and must be connected at the

OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:

BROWN/RED to pin 3 ( GRAY/ORANGE ) and BROWN/YELLOW to pin 11 ( VIOLET/

ORANGE ) at the OBDII.

There is no fi rmware on the module; fl ash the RR module.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

maestro.idatalink.com

6

Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-FOR01-DS-IG-EN