Hunter XC Owners Manual And Programming Instructions

XC
Residential Irrigation Controller
Owner’s Manual and
Programming Instructions
XC
RUN
SENSOR BYPASS
SYSTEM OFF
CURRENT TIME/DAY
ACTIVE
MANUAL-ALL STATIONS
MANUAL-ONE STATION
ALL
1
SEASONAL ADJUSTMENT
START TIMES
RUN TIMES
WATER DAYS
TABLE OF Contents
INSTALLATION
XC Components.. ....................................................................... 1-2
Mounting the Controller ............................................................... 3
Selecting Specific Days of the Week to Water.. ........................... 8
Selecting Odd or Even Days to Water.. ....................................... 8
Selecting Interval Watering....................................................... 9
Setting Event Day(s) Off.. .......................................................... 9
Automatic Watering.............................................................. 9
Connecting Valves and Transformer.. ............................................. 3
Activating the Battery................................................................... 3
Replacing the Battery.. .................................................................. 4
Connecting a Master Valve............................................................ 4
Connecting a Pump Start Relay.................................................... 4
Connecting a Weather Sensor....................................................... 5
Bypass Weather Sensor................................................................ 5
Power Failures.. ............................................................................ 5
CONTROLLER PROGRAMMING AND OPERATION
System Off......................................................................... 9
Programmable Rain Off.. ........................................................... 9
Seasonal Adjustment.. ........................................................10
1
Manually Run a Single Station...........................................10
ALL
Manually Run All Stations.. ................................................10
One Touch Manual Start and Advance.......................................10
Advanced Features.. .....................................................................11
Programmable Sensor Override.. ..............................................11
Test Program.. .........................................................................11
Watering Schedule Form............................................................... 6
Hunter Quick Check™.. .............................................................11
Programming the Controller.. ........................................................ 7
Easy Retrieve™ Program Memory.. ...........................................12
Setting the Date and Time.. .................................................. 7
Programmable Delay Between Stations.....................................12
Setting the Program Start Time........................................... 7
Clearing the Controller's Memory/Resetting the Controller........12
Eliminating a Program Start Time.............................................. 8
Setting Station Run Times.. ................................................. 8
Setting Days to Water......................................................... 8
TROUBLESHOOTING AND SPECIFICATIONS
Troubleshooting Guide............................................................13-14
Specifications.. ............................................................................14
CE Notice....................................................................................15
XC COMPONENTS
2 3 4 6 1
11
9
8
A
C
A
7
C
AM PM
%24HR
PRG
EVEN
2,4...30
PRG
MO TU WE TH FR SA SU ODD 1,3...29
XC
XC
12
13
5 10 14
RUN
RUN
SENSOR BYPASS
SENSOR BYPASS
SYSTEM OFF
CURRENT TIME/DAY
SYSTEM OFF
ACTIVE
ACTIVE
D
CURRENT TIME/DAY
MANUAL-ALL STATIONS
ALL
START TIMES
MANUAL-ONE STATION
1
RUN TIMES
SEASONAL ADJUSTMENT
MANUAL-ALL STATIONS
ALL
MANUAL-ONE STATION
1
RUN TIMES
SEASONAL ADJUSTMENT
WATER DAYS
24VAC
BAT
WATER DAYS
SEN
C
P
1
2
3
4
5
6
RST
24VAC
BAT
SEN
C
P
1
2
3
4
5
6
7
19
START TIMES
7
8
17
8
RST
18
Note: Plug may
look different from
Illustration.
17
B
15
Terminal block
for -E
15
18
16
Indoor Model
Outdoor Model
(Internal Transformer Included)
B
ENG
A – LCD Display
1. Run Times – Allows user to set each valve station run time
from 1 minute to 4 hours.
2. Start Times – Allows 1 to 4 start times to be set in each
program.
17. Terminal Strip – Use to attach transformer, sensor, and valve wires from
their source to the controller.
18. Reset Button – Use to reset the controller.
C – Control Buttons
Button – Increases the selected item flashing in the display.
3. Station Number – Indicates currently selected station number.
Button – Decreases the selected item flashing in the display.
4. Program Designator – Identifies program (A, B, or C) in use.
Button – Returns selected flashing display to previous item.
Button – Advances the selected flashing display to the next item.
5. Day of the Week – Identifies day of the week
6. Button – Selects program A, B or C for different watering zone
requirements.
Interval Watering – Identifies month when programming current date.
7. Odd/Even Watering – Identifies if Odd or Even watering has been
selected.
19. Sensor Bypass Switch.
8. Flashing Sprinkler – Indicates that watering is taking place.
Dial Settings
9. Run – Normal dial position for all controller automatic and manual
operation.
10.
System Off – Allows user to discontinue all programs and
watering. Also allows the user to set the programmable “rain off”
which stops watering for a period from 1 to 7 days.
Current Time/Day – Allows current day and clock time to be set.
Start Times – Allows 1 to 4 start times to be set in each program.
Umbrella – Indicates that the rain sensor is active.
Run Times – Allows user to set each valve station run time from 1
minute to 4 hours.
11.
Seasonal Adjustment – Allows the user to make run time
changes according to the seasons without reprogramming the
controller. Bars on the left allow quick visual reference to the
seasonal adjustment percentage.
Water Days – Allows the user to select interval days to water.
Seasonal Adjustment – Allows user to make run time changes according to the seasons without reprogramming the controller. Bars
on the left allow quick visual reference to the seasonal adjustment
percentage.
12. Rain Drop – Indicates watering will occur on the selected day.
13.
Crossed Rain Drop – Indicates the watering will NOT occur on
the selected day.
14.
Calendar – Indicates interval watering schedule has been
programmed. Icon also appears when programming the current day.
B – Wiring Compartment
15. Lithium Battery – The replaceable lithium battery (included) allows
the controller to be programmed in the absence of AC power. In
addition, the battery will provide power for backup timekeeping in
the event of a power outage.
16. Internal Junction Box – Junction box in outdoor models for
making AC power connections.
1
ALL
Manual-One Station – Allows user to activate a one-time watering
of a single valve.
Manual-All Stations – Allows user to activate a one-time watering
of all valve stations or a few selected stations.
System Off – Allows user to discontinue all programs and watering. Also allows the user to set the programmable rain off which
stops watering for a period from 1 to 7 days.
D – External Transformer (Indoor Model only)
A plug in transformer is provided to supply AC power to the controller.
MOUNTING THE CONTROLLER TO WALL
NOTE: The indoor XC is not waterproof or weather resistant, and must be installed indoors or in a protected area.
1. Secure one screw into the wall. Install screw anchors if attaching
to drywall or masonry wall.
2. Slide the keyhole on top of the controller over the screw.
3. Secure the controller in place by installing screws in the holes
below the terminal strip.
Do not plug transformer into power source until controller is mounted and all valve wiring has been connected.
CONNECTING VALVES AND TRANSFORMER
Installation of the XC should only be done by trained personnel.
1. Route valve wires between the control valve location and controller.
2. At valves, attach a common wire to either solenoid wire on all
valves. This is most commonly a white colored wire. Attach a
separate control wire to the remaining wire of each valve. All wire
connections should be done using waterproof connectors.
3. Route the valve wires through the conduit. Attach the conduit
through the bottom right side of the controller.
Valve 4
24VAC
BAT
SEN
C
P
1
2
3
4
5
6
7
Valve
Wires
Valve Common Wire
5. Indoor Models: route the transformer cable through the hole on
the left side of the controller and connect the wires to the two
screws marked 24VAC.
Outdoor Models: transformer wires are already connected to the
AC terminals so all that is required is to connect primary power to
the junction box (see below).
E – High Voltage Wiring (Outdoor Model only)
NOTE: XC outdoor models are water and weather resistant. Connecting the outdoor XC to primary AC power
should only be done by a licensed electrician following
all local codes. Improper installation could result in
shock or fire hazard.
1. Route AC power cable and conduit through the ½" (13mm) conduit
opening on the left side bottom of the cabinet.
2. Connect one wire to each of the two wires inside the junction box.
The ground wire should be connected to the green wire. Wire nuts
are provided to make these connections. Note: For –E models
only: Connect the wires to the AC terminal block inside the junction box. AC supply wires must be 14 AWG (1.85mm) or larger
with appropriate circuit breaker for the wire size. A switch or circuit-breaker shall be included in the building installation (in close
proximity to the controller, within easy reach of the operator) and
marked as the disconnecting device for the equipment.
Valve 3
3. Replace the junction box cover.
Valve 2
Activating THe Battery
8
RST
Connect the Two
Transformer Wires to
the Two AC Terminals
4. Secure the white valve common wire to the C (Common) screw on
the terminal strip. Attach each of the individual valve control wires
to the appropriate station terminals and tighten their screws.
Valve 1
After installing your XC make sure to remove the battery contact insulator to allow the XC to keep time in
the event of a power outage.
ENG
REPLACING THE BATTERY
Lithium Battery
A high-energy lithium battery is included with your
XC controller. The battery allows the user to remotely
program the controller without connecting AC power.
It is also used to keep the current time and day during
power outage conditions. To replace the battery:
1. Remove the screw from the battery holder.
2. Slide the battery holder down to
access the battery.
Battery
(+)
(--)
Holder
Battery Compartment
SEN
24VAC
C
P
1
2
3
4
5
6
7
8
RST
3. Remove and replace the new battery
into the battery holder and reinstall the
battery holder.
2. The common wire should be attached to the C terminal inside the
controller. The other wire coming from the master valve should be
attached to the P terminal inside the controller. Tighten each terminal screw.
CONNECTING A PUMP START RELAY
NOTE: Complete this section only if you have a pump
start relay installed. A pump start relay is a device that
uses a signal from the controller to actuate a separate
electrical circuit to energize a pump to provide water to
your system.
BAT
The controller should be mounted at least a 15 ft (4.5 m) away from
both the pump start relay and pump to minimize any potential electrical interference.
NOTE: This positive (+) side of the battery should face
the inside of the battery holder.
1. Route a pair of wires from the pump relay into the controller.
Battery type: CR2032 3V
2. Connect a common wire to the C (Common) terminal inside the
controller and connect the remaining wire from the pump start
relay to the P terminal.
CONNECTING A MASTER VALVE
NOTE: Complete this section only if you have a master
valve installed in your irrigation system. A master valve
is a "normally closed" valve installed at the supply point
of the main line that opens only when the controller
initiates a watering program.
Relay holding current draw must not exceed .30 amps. Do not connect
the controller directly to the pump or damage to the controller will result.
PSR Series
Pump Start Relay
XC
RUN
SENSOR BYPASS
1. At the Master Valve,
attach the common wire
to either solenoid wire
of the valve. Attach a
separate control wire to
the remaining solenoid
wire.
SYSTEM OFF
CURRENT TIME/DAY
ACTIVE
MANUAL-ALL STATIONS
MANUAL-ONE STATION
Valve 4
24VAC
BAT
SEN
C
P
1
2
3
4
5
6
7
ALL
1
SEASONAL ADJUSTMENT
START TIMES
RUN TIMES
WATER DAYS
4.5 Meters Minimum (15')
8
RST
Valve 3
Master Valve Wire
Valve 2
Valve
Wires
To Pump
Valve 1
Master Valve
Valve Common Wire
Testing the Weather Sensor
CONNECTING A WEATHER SENSOR
A Hunter weather sensor or other micro-switch type weather sensors
can be connected to the XC. The purpose of this sensor is to stop
automatic watering when weather conditions dictate.
1. Remove the metal jumper plate that is attached across the two
SEN terminals inside the controller.
2. Connect one wire to one SEN terminal and the other wire to the
other SEN terminal.
Mini-Clik ® Rain Sensor
24VAC
BAT
SEN
RST
C
P
1
2
3
4
5
6
7
8
The XC provides simplified testing of a rain sensor when the sensor is
wired into the sensor circuit. You can manually test proper operation
of the rain sensor by running a manual all stations cycle or by
activating the system using the One Touch Manual Start (see page
10). During the Manual cycle, pressing the test button on the MiniClik ® will interrupt watering.
Manually Bypassing the Weather Sensor
If the rain sensor is interrupting irrigation you can
bypass it by using the bypass switch on the front of
the controller. Slide the switch to the SENSOR BYPASS
position to disable the rain sensor from the system
to allow for controller operation. You can also bypass
the weather sensor for manual operation by using the
MANUAL – ONE STATION function.
BYPASS
/DAY
ACTIVE
POWER FAILURES
When the weather sensor has deactivated
automatic watering, the OFF and
icon
will appear on the display.
Due to the possibility of power failures, the controller has non-volatile
memory. Programmed information will never be lost due to a power
outage. The lithium battery will keep the correct time without AC
power. Normal watering will resume when AC power is restored.
ENG
WATERING SCHEDULE
HUNTER XC
PROGRAM A
DAY OF THE WEEK
MO TU
WE
TH
FR
SA
PROGRAM B
PROGRAM C
STATION RUN TIME
STATION RUN TIME
SU
ODD/EVEN OR INTERVAL
1
PROGRAM
START TIMES
2
3
4
STATION
LOCATION
STATION RUN TIME
1
2
3
4
5
6
NOTES:
CURRENT TIME/DAY
PROGRAMMING THE CONTROLLER
The XC display shows the time and day when the controller is idle.
The display changes when the dial is rotated to indicate the specific
programming information to enter. When programming, the flashing portion of the display can be changed by pressing the
or
buttons. To change something that is not flashing, press the or
buttons until the desired field is flashing.
Three programs A, B, and C, each with the ability to have four daily
start times, permit plants with different watering requirements to be
separated on different day schedules.
NOTE: A basic programming rule is that whatever symbol
or character is flashing will be the item programmed. For
instance, if the hour is flashing when setting the time, the
hour can be changed or programmed. For illustration purposes in this manual, flashing characters are in GRAY type.
Setting the Date and Time
1. Turn the dial to the CURRENT TIME/DAY position.
2. The current year will be flashing. Use the
or
buttons to change the year. After setting
the year, press the button to proceed to
setting the month.
3. The month and day will be in the display.
The month will be flashing and the
icon
will be displayed. Use the
or
buttons
to change the month. Press the
button to
proceed to setting the day.
4. The day will be flashing and the
icon
will be displayed. Use the
or
buttons
to change the day. Press the button to
proceed to setting the time.
CURRENT TIME/DAY
and
5. The time will be displayed. Use the
buttons to select AM, PM, or 24 hour.
Press the button to move to hours. Hours
will be flashing. Use the
and
buttons
to change the hour shown on the display.
Press the button to move to minute.
Minutes will be flashing. Use the
and
buttons to change the minutes shown on the
display. The date, day, and time have now
been set.
Setting the Program Start Time(s)
1. Turn the dial to the START TIMES position.
2. The factory preset is set on program A. If
necessary, you can select program B, or C
by pressing the
button.
START TIMES
3. Use the
or
button to change the
start time. (The start times advance in
15 minute increments).
4. Press the
button to add an additional start time, or
for the next program.
button
NOTE: One start time will activate all stations sequentially in that program. This eliminates the need to enter each
station’s start time. Multiple start times in a program
can be used for separate morning, afternoon, or evening
watering cycles. Start times may be entered in any order.
The XC will automatically sort them.
ENG
Eliminating a Program Start Time
START TIMES
With the dial set to START TIMES position,
push the
or
button until you reach
12:00 AM (Midnight). From here push the
button once to reach the OFF position.
1. With the cursor on a specific day
(the cursor will always start with MO),
press the
button to activate a particular
Mo Tu We Th Fr Sa Su
day of the week to water. Press the
button to cancel watering for that day. After pressing a button the
cursor automatically advances to the next day.
Setting Station Run Times
1. Turn the dial to RUN TIMES position.
2. The display will show the last program
selected (A, B, or C), the station number
selected, icon, and the station will be
flashing. You can switch to another program by pressing the
button.
RUN TIMES
button to advance to the next station.
Setting Days To Water
This feature uses numbered day(s) of the month for watering instead
of specific days of the week (odd days: 1st, 3rd, 5th, etc.; even days:
2nd, 4th, 6th, etc.).
1. With the cursor on Su press the button
once. The icon and odd will be displayed.
2. If odd day watering is desired, turn the dial
back to the run position.
1. Turn the dial to the WATER DAYS position.
2. The display will show the last program selected (A, B, or C). You can switch to another
program by pressing the
button.
2. Repeat step 1 until all desired days have been selected. The
selected days will show a to indicate their status is ON. The last
is the last day of watering for that program.
Selecting Odd or Even Days to Water
3. Use the
or
button to change the station run time on the
display. You can set the run times from 0 to 4 hours.
4. Press the
Selecting Specific Days of the Week to Water
WATER DAYS
3. The controller will display the seven days of the week (MO, TU,
WE, TH, FR, SA, SU). Each day will have a icon or a
icon
above the day. The icon would represent an “On” water day,
while a
icon would represent an “Off” watering day.
3. If even day watering is desired, press the
button once. The icon and EVEN will be
displayed. You can move back and forth from
ODD to EVEN by pressing the and buttons.
Odd Day Watering
Even
2, 4,...30
Even Day Watering
NOTE: The 31st of any month and February 29th are
always “off” days if Odd watering is selected.
PROGRAMMING THE CONTROLLER (cont.)
Selecting Interval Watering
With this option you can select interval watering from 1 to 31 days.
1. With the cursor on EVEN, press the
button once and the
icon will appear and a 1 flashing in the
display. Interval watering schedule appears on the display.
2. Press the
or
button to select the number of days between
watering days (from 1 to 31 days). This is called the interval.
The controller will water the selected program at the next start time
and will then water at the interval programmed.
Setting Event Day(s) Off
The XC allows you to program a No Water Day(s). This feature is useful to inhibit watering on specific day(s). For example, if you always
mow the lawn on Saturdays, you would designate Saturday as a No
Water Day so that you are not mowing wet grass.
1. Turn the dial to the WATER DAYS position.
RUN
After programming the XC, set the dial to the RUN position
to enable automatic execution of all selected watering
programs and start times.
System Off
SYSTEM OFF
Valves currently watering will be shut off after the
dial is turned to the SYSTEM OFF position for two
seconds. All active programs are discontinued and
watering is stopped. To return the controller to normal
automatic operation, simply return the dial to the RUN position.
Programmable Rain Off
This feature permits the user to stop all programmed waterings for
a designated period from 1 to 7 days. At the end of the programmed
rain off period, the controller will resume normal
automatic operation.
SYSTEM OFF
1. Turn the dial to the SYSTEM OFF position.
Wait for OFF to be displayed.
2. Enter an interval watering schedule as described on page 8.
2. Press the
button as many times as needed to
set the number of days off (up to 7 days).
3. Press the button to scroll to the No Water Days at the bottom of
the display. MO will be flashing.
3. Turn the dial back to the RUN position at which OFF, a
number, the
and
icons will be displayed.
4. Use the button until the cursor is at the day of the week you
wish to set as a No Water Day.
The days off remaining will decrease at midnight
each day. When it goes to zero, the display will show
normal time of day and normal irrigation will resume
at the next scheduled start time.
5. Press the
button to set this day as a no water day. The
illuminate over this day.
will
6. Repeat steps 4 and 5 until all desired event day(s) are off.
NOTE: You also have the option in the interval watering
schedule to program Odd or Even days off.
Automatic Watering
RUN
ENG
Seasonal Adjustment
Manually Run All Stations
Seasonal Adjust is used to make global run time changes without
re-programming the entire controller. To use the seasonal adjustment
feature:
1. Turn dial to MANUAL – ALL STATIONS
position.
1. Turn the dial to the SEASONAL
ADJUSTMENT position.
SEASONAL ADJUSTMENT
2. The display will now show a flashing number
followed by a %, as well as the bar graph which
always remains on the display. Press the
or
button to adjust the percentage of the seasonal adjustment. Each
bar on the graph represents 10%. This feature can adjust the controller from 10% to 150% of the original program.
To view the adjusted run times, simply turn the dial to the RUN TIMES
position, the displayed run time will be updated accordingly as the
seasonal adjustment is made.
NOTE: The controller should always be initially
programmed in the 100% position.
Manually Run a Single Station
MANUAL-ONE STATION
1
2. Station run time will flash in the display. Use the button to
move to the desired station. You may use the
or
button to
select the amount of time for a station to water.
3. Turn the dial clockwise to the RUN position to run the station (only
the designated station will water, then the controller will return to
automatic mode with no change to the previously set program).
Also see One Touch Start and Advance.
MANUAL-ALL STATIONS
2. Select program A, B, or C by pressing the
ALL
button.
3. Station run time will flash in the display. Use the
or
button
to select the amount of time for a station to water if different from
the run time displayed.
4. Use the
button to move to the next station.
5. Repeat steps 3 and 4 to customize each station.
6. Press the button until you reach the station at which you would
like watering to begin.
Turn the dial clockwise to the RUN position (the controller will water
the entire program beginning with the station number last left in the
display, then return to the automatic mode with no change in the
previously set program).
One Touch Manual Start and Advance
You can also activate all stations to water without using the dial.
1. Hold down the
1
1. Turn dial to MANUAL – ONE STATION
position.
ALL
button for 2 seconds.
2. This feature automatically defaults to program A. You can select
program B or C by pressing the
button.
3. The station number will be flashing. Press the button to scroll
through the stations and use the
or
button to adjust station
run times. (If no buttons are pressed for a few seconds during
step 2 or 3, the controller will automatically begin watering).
4. Press the button scroll to the station you wish to begin with.
After a 2 second pause, the program will begin. At any time during
the manual cycle, you can use the or buttons to navigate
from station to station manually.
10
Test Program of All Stations
ADVANCED FeatureS
Programmable Sensor Override
The XC allows the user to program the controller so that the sensor
disables watering on only desired stations. For example, patio gardens
that have pots under overhangs and roofs may not receive water when
it rains and will continue to need to be watered during periods of rain.
To program sensor override:
1. Turn the dial to the RUN position.
RUN
ON = Sensor enabled (will suspend irrigation)
OFF = Sensor disabled (will allow watering)
Sensor Enable
This feature allows you to quickly diagnose wiring problems with
your controller. Instead of having to check each field wiring circuit for
potential problems, you can use the Hunter Quick Check circuit test
procedure. To initiate the Quick Check test procedure:
1. Press the , ,
, and
buttons simultaneously. In the standby mode, the LCD will display all segments.
Sensor Disabled
5. Use the or buttons to scroll to the next station that you would
like to program the sensor override.
NOTE: The controller default is for the sensor to disable
watering on all zones when rain occurs.
When the XC receives an input from the sensor to
disable watering, the display will indicate those
stations that have been programmed to override the
sensor. A station that is running in the sensor override mode will flash
the
and icons alternately.
11
2. Use the
or
buttons to set the run time from 1 to 15 minutes.
The run time needs to be entered only once.
Hunter Quick Check™ Diagnostics
3. Release the
button. At this point, the display
will show the station number, ON, and the
icon,
will be flashing.
1. With the dial in the RUN position, press and hold the
button.
The station number will be displayed and the time will be flashing.
3. After a 2 second pause, the test program will start.
2. Press and hold the
button down while turning
the dial to START TIMES position.
4. Press the
or
button to enable or disable the
sensor for the station shown.
The XC allows the user a simplified method for running a test program. This feature will operate each station in numerical sequence,
from the lowest to the highest.
2. Press the
button once to begin the Quick Check procedure.
Within seconds, the system searches all stations for detecting any
circuit problems. When a field wiring short is detected, an ERR
symbol preceded by the station number will momentarily flash on
the display. After the Quick Check completes running the circuit
diagnostic procedure, the controller returns to the automatic
watering mode.
ENG
Easy Retrieve™ Program Memory
Clearing the Controller's Memory/Resetting the Controller
The XC is capable of saving the preferred watering program into memory for retrieval at a later time. This feature allows for a quick way of
resetting the controller to the original programmed watering schedule.
If you feel you have misprogrammed the controller, there is a process
that will reset the memory to the factory defaults and erase all programs and data that have been entered into the controller.
To save the program into the memory.
1. Press and hold down the
1. With the dial in the RUN position, press and hold the
and
buttons for 5 seconds. The display will scroll three segments
from left to right across the display indicating the program is
being saved into memory.
2. Press and release the reset button in the lower wiring compartment.
2. Release the
and
buttons.
,
, and
buttons.
3. Wait 2 seconds and release the
, , and buttons. The display
should now show 12:00 am. All the memory has been cleared and
the controller may now be reprogrammed.
To retrieve a program that was previously saved into memory.
1. With the dial in the RUN position, press and hold the
and
buttons for 5 seconds. The display will scroll three segments
from right to left across the display indicating the program is being saved into memory.
2. Release the
and
buttons.
Programmable Delay Between Stations
This feature allows the user to insert a delay between stations between
when one station turns off and the next one turns on.
1. Start with the dial in the RUN position.
2. Press and hold the
button down while turning the dial to the
RUN TIMES position.
3. Release the
button. At this point the display will show a delay
time for all stations in seconds, which will be flashing.
4. Press the
or
buttons to increase or decrease the delay time
between 0 and 4 hours.
5. Return the dial to the RUN position.
12
TROUBLESHOOTING GUIDE
PROBLEM
CAUSES
SOLUTIONS
The controller is continuously watering.
Too many start times have been programmed.
Only one start time is necessary to activate a program.
(refer to Setting Watering Start Times on page 7).
There is no display.
Check AC power wiring.
Correct any errors.
The display reads “No AC”.
There is no AC power present (the controller
is not receiving any power).
Check to see if the transformer is properly installed.
Display reads “Off,
”.
Rain sensor will not shut off the system.
The rain sensor is interrupting irrigation or the Slide the rain sensor bypass switch to the BYPASS position to
sensor jumper has been removed.
bypass the rain sensor circuit, or reinstall the jumper.
Defective rain sensor.
Verify operation of rain sensor and proper wiring
Jumper was not removed when sensor
was installed.
Remove jumper from the sensor
terminals.
Stations have been programmed to override
the sensor.
Reprogram the sensor override to enable the sensor
(see page 10).
Frozen display, or showing incorrect
information.
Power surge.
Reset the controller per page 11 “Clearing Controller Memory/
Resetting the Controller”.
Display shows “ERR” with a number (1-8).
Short in valve wiring circuit, or faulty solenoid
on the station number indicated.
Check wire circuit or solenoid for the valve number indicated.
Repair short or replace solenoid. Press any button to clear the
“ERR” from the display.
Display shows “P ERR”.
Faulty pump relay or master
valve wiring.
Check wiring to relay or master valve solenoid. Press any button
to clear the “P ERR” from the display.
Incompatible or defective relay or solenoid.
Check electrical specification for the pump relay. Do not exceed
controller's electrical rating. Replace if defective.
Replace wire with larger gauge wire.
Under sized wire to the pump relay or
master valve.
13
ENG
TROUBLESHOOTING GUIDE (cont.)
PROBLEM
CAUSES
SOLUTIONS
Display shows a station is running but the
and icons are flashing.
The sensor is interrupting irrigation, however
the station has been programmed to
override the sensor.
Check the sensor override status (see page 10).
Automatic irrigation does not start at the
start time and controller is not in the
System Off mode.
AM/PM of time of day not set correctly.
Correct AM/PM of time of day.
AM/PM of start time not set correctly.
Correct AM/PM of start time.
Start Time is disabled (set for Off).
See Setting Start Times (pg 7).
Controller is not receiving AC power.
Check AC power connections.
SPECIFICATIONS
Operating Specifications
Electrical Specifications
•
•
Station Run Times: 0 to 4 hours in 1-minute
increments.
Transformer input 120VAC ±10% 60 Hz
(230VAC ±10% 50/60 Hz International
Models).
•
3 Independent Watering Programs.
•
Start Times: 4 per day per program for
up to 12 daily starts.
•
Transformer Output: 24VAC 1.0 amp.
•
Station Output: .56 amps per station.
•
Watering Schedule: 365-day calendar,
interval watering, odd/even watering.
•
Maximum Output: .90 amps
(includes master valve).
•
AM/PM, 24-hour clock.
•
•
Simple manual operation.
•
Sensor override by station.
Battery: 3V Lithium (included) used for remote programming and backup timekeeping. Use CR2032 3-volt.
•
Programmable rain delay (1 to 7 days).
•
Electronic short circuit protection.
•
Seasonal adjustment (10% to 150%).
•
Non-volatile memory for program data.
•
Sensor bypass switch.
•
UL Listed.
•
XC-x00i for indoor use. XC-x00 for
outdoor use.
•
Model XC-x00 has an IP24 Rating for
Pollution Degree 4.
•
Sea level to 2000m at 0-50°C.
•
Clean only with a cloth dampened with
mild soap and water.
Explanation of Symbols
= AC
= Consult Documentation
= Hazardous Voltages Present
= Ground
14
Certificate of Conformity to european directives
Hunter Industries declares that the irrigation controller Model XC complies with the standards of the European Directives of “electromagnetic
compatibility” 87/336/EEC and “low voltage” 73/23/EEC.
__________________________________
Project Engineer
This product should not be used for anything other than what is described in this document. This product should only be serviced by trained and
authorized personnel.
FCC part 15:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Hunter Industries Incorporated • The Irrigation Innovators
Internet: www.HunterIndustries.com
© 2006 Hunter Industries Incorporated
LIT-397
P/N 701013
9/06
">