Miele PG 8083 SCVi Commercial Dishwasher Operating Instructions
Реклама
Реклама
Operating Instructions
Commercial Dishwasher
PG 8083 SCVi
To prevent accidents and machine damage, read these instructions before installation or use.
en - US
M.-Nr. 09 501 402
Contents
Before using the machine for the first time, you will need: ................................... 21
Example of load with 10 place settings with cutlery tray ...................................... 27
Example of load for 16 place settings with cutlery tray ........................................ 28
2
Contents
3
Contents
Cleaning the drain pump and non-return valve..................................................... 71
4
Guide to the manual
Warnings
Information which is important for safety is highlighted by a thickly framed box with a warning symbol. This alerts you to a potential risk of personal injury or property damage.
Read these warning notes carefully and follow any procedural instructions and operating prompts.
Notices
Notes contain information that requires particular attention.
They are highlighted by a thickly framed box.
Additional information and comments
Additional information and comments are marked by a box with thin line.
They are not necessarily critical to the operation of the dishwasher.
Operating steps
Additional instructions on how to operate the dishwasher are described step-by-step in a logical sequence.
Each new step is marked by a black square bullet point.
Example:
Select the desired setting and press the center button to confirm.
Display
In this manual, information that is shown in the dishwasher display appears in a special font similar to the display text.
Example:
When the message End or AutoOpen appears in the display ....
5
Proper use
This dishwasher complies with current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property.
To avoid the risk of accidents and damage to the dishwasher, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance. Keep these instructions in a safe place and pass them on to any future owner.
This dishwasher with its short program running times and powerful cleaning performance is intended for commercial use in office kitchens, clubhouses, small businesses, active kitchens and other similar commercial environments.
It is also suitable for use in domestic households and in similar residential environments, for example, by customers in hotels, motels, bed and breakfast and other related establishments.
This dishwasher is not intended for continuous use.
This commercial dishwasher is not suitable for the cleaning of medical products or devices.
This appliance is designed exclusively for use as a "dishwasher" for cleaning cookware, glassware and cutlery only, as described in these instructions. Alterations or conversions to the dishwasher, or using it for purposes other than those for which it is designed, are not permitted and could be dangerous.
Miele cannot be held liable for damage caused by improper or incorrect use or operation.
This commercial dishwasher is intended only for stationary indoor use.
The special inserts are to be used for their specific purpose only.
Persons who lack physical, sensory or mental abilities, or experience with the appliance should not use it without supervision or instruction by a responsible person.
6
Proper use
This dishwasher is supplied with a special bulb to cope with particular conditions (e.g. temperature, moisture, chemical resistance, abrasion resistance and vibration). This special bulb must only be used for the purpose for which it is intended, i.e. to illuminate the wash chamber. It is not suitable for room lighting. Replacement of bulbs may only be carried out by a Miele-authorized technician.
7
Important safety instructions
Proper installation
Do not install the commercial dishwasher in areas at risk of explosion or freezing.
To ensure the stability of undercounter commercial dishwashers, they must only be installed beneath a continuous countertop that is bolted to the adjacent cabinetry.
In order to reduce the risk of damage from condensation, the furniture in the area around the commercial dishwasher should be designed for commercial use.
Technical safety
The commercial dishwasher must only be installed, commissioned, repaired and then maintained by the Miele Service
Department or an authorized Miele Service dealer. Installation, repair and other work by unqualified persons could be dangerous and
Miele will not be held liable.
This commercial dishwasher must only be operated by appropriately trained personnel. They must be instructed and trained regularly.
Before using the commercial dishwasher, check it for any externally visible damage. Under no circumstances should you use it if it has been damaged. It could be dangerous.
In the event of a damaged or leaking commercial dishwasher, turn it off immediately and contact Miele or an authorized Miele Service dealer.
Faulty components may only be replaced by genuine Miele original parts. Only when these parts are fitted can Miele guarantee the safety standards of the appliance.
8
Important safety instructions
The electrical safety of this commercial dishwasher can only be guaranteed when it is connected to a correctly installed grounding conductor system. If in any doubt, please have the electrical installation tested by a qualified electrician. Miele cannot be held liable for the consequences for the lack or interruption of a grounding conductor (e.g. electric shock).
Be sure to follow the installation instructions in this manual and in the installation diagram.
Ensure that the connection data on the data plate (voltage, frequency, and fuse rating) match those of your electrical supply.
There must be no electrical sockets behind the commercial dishwasher since the depth of the installation niche may be too small and there is a danger of overheating if the dishwasher is pushed up against a plug (see the "Electrical connection" chapter for more information).
Do not connect the dishwasher to the electrical supply by a multiple outlet box or an extension cable since they do not guarantee the required safety of the appliance (e.g. danger of overheating).
Do not open the commercial dishwasher casing under any circumstances. Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults.
The commercial dishwasher must not be used if the connecting cable is damaged. If the cable is damaged, it must be replaced with a special connecting cable available from Miele. For safety reasons, this may only be performed by the Miele Service Department or an authorized Miele Service dealer.
Before maintenance, disconnect the commercial dishwasher from the electrical supply.
The plastic housing of the water connection contains electrical components. It must not be dipped in water.
9
Important safety instructions
There are live wires in the water intake hose. Do not shorten the water intake hose, even if it is too long.
The built-in waterproof system offers reliable protection against water damage if the following conditions are met:
– proper installation
– proper maintenance of the dishwasher or exchange of parts in case of visible damage
– closing of the water valve during longer absences (for example vacation)
The waterproof system will work even if the dishwasher is turned off.
However, the commercial dishwasher must remain connected to the electrical supply.
10
Important safety instructions
Correct use
This commercial dishwasher is designed for operation with water and detergents suitable for use in commercial dishwashers only.
Organic solvents and flammable liquid agents must not be used.
This could cause an explosion, property damage due to the destruction of rubber or plastic, and the resulting leakage of liquids.
Use detergents formulated for use in commercial dishwashers.
Using unsuitable detergents could damage the dishes and the commercial dishwasher itself.
Do not sit or lean on the opened door. This could cause the commercial dishwasher to tip or become damaged.
After any plumbing work on the water supply, to the dishwasher will need to be vented. If this is not done, components can be damaged.
Please be aware that the dishwasher may be operating at high temperatures. If the door is opened, there is a danger of burning or scalding. Dishes, cutlery, baskets, and inserts must be allowed to cool down before they are unloaded. Any water remaining in containers could still be very hot. Empty them into the wash cabinet before taking them out.
The water in the wash cabinet is NOT safe to drink!
The pretreatment of items (for example with dishwashing liquid and other detergents), but also some types of soiling and some detergents, can cause a build-up of foam in the wash cabinet. Foam can have an adverse effect on the cleaning result.
Foam escaping from the wash chamber can cause damage to the dishwasher. If foam escapes, the program must be cancelled immediately and the machine must be disconnected from the electrical supply.
11
Important safety instructions
When using detergents and specialized products, it is essential that the manufacturer's instructions are followed. Detergents must only be used for the purpose they are designed for and in the situation specified, to avoid material damage and serious chemical reactions (e.g. oxyhydrogen explosion).
Do not inhale or ingest powder detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Seek medical attention immediately if detergent has been swallowed or inhaled.
Miele cannot be held liable for any effect chemical detergents may have on the material of the items being cleaned. Observe the detergent manufacturer's instructions with regard to storage conditions, use, and dosage.
To avoid material damage and corrosion, do not allow any acids or solutions containing chloride to get into the wash cabinet.
Similarly avoid any materials with a corrosive effect.
Do not wash items soiled with ash, sand, wax, lubricants, or paint in the dishwasher. These substances could damage the dishwasher.
Do not hose down the dishwasher or its direct vicinity to clean it, e.g. with a water hose or high-pressure cleaner.
Ensure that the stainless steel outer casing of the appliance does not come into contact with solutions or steam containing acid to avoid any corrosion damage.
Be careful when sorting items with sharp pointed ends and positioning them in the dishwasher so that you do not hurt yourself or create a danger for others. Cutlery should be placed in baskets in such a way that no injuries can occur.
Remove any coarse food deposits from the items being cleaned before loading them in the dishwasher.
12
Important safety instructions
Children in the vicinity
Supervise children when they are anywhere near this dishwasher.
Do not let them play with it. There is a danger that children may lock themselves in the dishwasher.
Keep children away from chemical agents. These contain irritant and corrosive ingredients which can cause burning in the mouth, nose and throat if swallowed, or inhibit breathing. Keep children away from the dishwasher when the door is open. There could still be residual chemical agent in the cabinet. Seek medical advice immediately if a child has swallowed or inhaled chemical agent.
Accessories
Accessories may only be fitted if approved by Miele. If other parts are used, any warranty and product liability claims shall be void.
Miele cannot be held liable for damage caused by failure to comply with these safety instructions and warnings.
SAVE THESE INSTRUCTIONS
13
Product description
Machine overview a Upper spray arm (not visible) b Cutlery tray c Upper basket d Middle spray arm e Air intake for drying f Lower spray arm g Filter combination h Data plate i In-operation indicator light j Rinse aid reservoir k Dual-compartment detergent dispenser l Reservoir for reactivation salt
14
Product description
Control panel a Display b Additional Programs button with indicator light c Delay Start button with indicator light d Extra Drying button + with indicator light e Program selection f Program Selection button
g Button (On/Off) h In-operation indicator light
15
Caring for the environment
Disposal of the packing material
The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable.
Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Danger of suffocation!
Disposal of your old appliance
Electrical and electronic appliances contain valuable materials. They also contain certain substances, compounds and components which were essential for the proper functioning and safe use of the equipment. Handling these materials improperly by disposing of them in your household waste can be harmful to your health and the environment. Therefore, please do not dispose of your old appliance with regular household waste and follow local regulations on proper disposal.
Consult with local authorities, dealers or
Miele in order to dispose of and recycle electrical and electronic appliances.
Miele assumes no responsibility for deleting any personal data left on the appliance being disposed. Please ensure that your old appliance is kept away from children until removal.
Observe safety requirements for appliances that may tip over or pose an entrapment hazard.
16
Caring for the environment
Energy-saving washing
This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your machine by following these tips:
You may connect the dishwasher to a hot water supply. This is particularly suitable with energy-saving water heating sources such as solar energy systems. If the hot water system is electrically heated and if loads consist primarily of glassware, we recommend connecting the machine to the cold water supply.
For most economical dishwashing, make full use of the baskets without overloading the dishwasher.
Choose a program that best suits the degree of soiling and the type of dishes being washed.
Select the Normal program for energy-saving dishwashing. This program is the most efficient in terms of its combined energy and water consumption at cleaning normally soiled tableware.
Follow the detergent manufacturer's recommendations on detergent dosage.
When using powder detergent you can use 1/3 less detergent if baskets are only half full.
17
Commissioning
Opening the door Closing the door
Insert the baskets.
Then lift the door upwards and push until it clicks into position.
Do not put your hand inside the door as it is closing.
Risk of injury!
At the end of programs with a drying phase (see "Program overview"), the door will open automatically a little in order to help the drying process.
This function can be deactivated if preferred (see "Settings, AutoOpen").
Pull the handle to open the door.
If the door is opened during operation, all functions are automatically interrupted.
Keep the area around the door free of obstructions.
18
Commissioning
Display functions
General information
The following functions can be selected or set with the display:
– The program
– The delay start time
– The settings
The following appears in the display while a program is running:
– The program stage
– The estimated time left for the program to run
– Any relevant fault messages and information
To save energy, the dishwasher will switch to Standby-mode within a few minutes if no program is running and no button is pressed. After several more minutes it switches off completely (see "Operation,
Standby").
To turn the dishwasher back on, press the button.
Settings menu
The Settings menu is used to alter the dishwasher's electronics to suit different requirements.
You access the Settings menu by pressing a specific button combination.
For more information see "Settings menu".
In the Settings menu, the normal functions of the buttons to the right of the display are not active, allowing you to select and confirm menu options with these buttons.
The left and right arrows in the display indicate that additional options are available. You can use the left or right arrow buttons beside the display as appropriate to select these further options.
Use the center button beside the display to confirm messages or settings and to switch to the next menu or submenu.
A check will appear beside the option which is currently selected.
19
Commissioning
Standard settings
Switch the dishwasher on with the button.
If the dishwasher is being turned on for the first time, the welcome screen will appear.
Language
The display will change automatically to the screen for setting the language.
See "Guide to the appliance, Display" for more information about the display and controls.
Select the desired language and press the center button to confirm.
A check will appear next to the language that has been set.
Water hardness
The display changes to the screen for setting the water hardness.
– The dishwasher must be programmed to match exactly the hardness of your water.
– Your local water supplier can tell you the water hardness level in your area.
– Where the water hardness fluctuates, e.g. between 18 - 26 gr/gal (17 -
25 °d - German scale), always program the dishwasher to the higher value (26 gr/gal or 25 °d in this example).
It is useful to know your water hardness so that you can provide the service technician with this information in the event of any service calls.
Enter the water hardness below:
____________ gr/gal (°d)
The dishwasher is programmed at the factory for a water hardness level of
15 °gr/gal (15 d - German scale).
Select the water hardness level for your water supply and confirm with the center button.
See "Settings menu, Water hardness" for more information.
The following two messages Refill rinse aid and Refill salt may then appear in the display.
Press any button to confirm them. The display will change to show the main menu.
20
Before using the machine for the first time, you will need:
– Approx. 2.2 lbs (1 kg) of dishwasher salt
– approx. 110 ml rinse aid,
– Dishwasher detergent, see
"Operation".
Every dishwasher is tested at the factory. There will be residual water in the machine from this test. It is not an indication that it has been used previously.
Filling the salt compartment
In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in a build-up of calcium deposits on tableware and in the dishwasher.
Water with a hardness level higher than
0.7 mmol/l (4 gr/gal (4 °d - German scale)) needs to be softened. This takes place automatically in the integrated water softener. The water softener assembly in the dishwasher is suitable for a water hardness level of up to
6.5 mmol/l (38 gr/gal (36°d - German scale)).
See "Settings menu, Water hardness" for more information.
Commissioning
If the water in your area is very soft and constantly lower than 0.7 mmol/l
(4 gr/gal (4 °d - German scale)), you do not need to add dishwasher salt.
The dishwasher must, however, still be programmed for the water hardness level in your area.
Do not fill the salt compartment with dishwasher detergent (including liquid detergent).
Dishwasher detergent will damage the softener assembly.
Only use special coarse-grained dishwasher salt for reactivation, or pure evaporated salt.
Miele Professional offers appropriate products.
Other types of salt may contain insoluble components which can cause the water softener to malfunction.
21
Commissioning
When adding salt, only open the door half way to avoid spills.
Press the button on the lid of the salt compartment in the direction of the arrow until the flap springs open.
Add salt only until the reservoir is full.
The salt reservoir holds approx. 2.2
lbs (1 kg) of salt, depending on the type of salt used.
Do not add any more than 2.2 lbs
(1 kg) of salt.
If there is water present in the compartment, it may be forced out by the added salt.
Clean any excess salt from around the reservoir opening, and then close the flap.
Run the "Pre-rinse" program immediately without a load in order to remove any traces of salt from the chamber.
Open the funnel.
Do not pour any water into the salt compartment!
22
Salt indicator
Fill the salt reservoir with dishwasher salt for reactivation when Refill salt appears in the display.
Press the center button to confirm.
The salt refill indicator will go out.
After the salt reservoir has been filled, the salt indicator may still appear in the display if the salt concentration has not yet reached the correct level. If this is the case, confirm again with the center button.
The salt indicator is deactivated if the dishwasher is set to a water hardness below 4 gr/gal (4 °dH - German scale).
Run the "Pre-rinse" or "Short" program immediately without a load in order to remove any traces of salt from the chamber.
Commissioning
Rinse aid
Rinse aid is needed to prevent spotting on dishes and glassware.
The rinse aid is filled in the reservoir and the set amount will be automatically dosed.
Fill the reservoir with rinse aid only. Do not fill it with liquid dish soap or cleaning agent.
This would damage the rinse aid reservoir.
Suitable products are available from
Miele Professional.
Alternatively household vinegar with a max. 5 % acid content or liquid citric acid with a max. 10 % acid content can be used. The resulting rinsing and drying quality will not, however, be as good as when rinse aid is used.
Do not use vinegar with a higher acid content (e.g. vinegar essence
25 % acid).
This would damage the dishwasher.
23
Commissioning
Adding rinse aid
Press the button on the lid of the rinse aid reservoir in the direction of the arrow until the flap springs open.
Wipe up any spilled rinse aid. This prevents over-foaming occurring during the next program.
You can adjust the rinse aid dosage for best results (see "Settings menu -
Rinse aid").
Rinse aid indicator
When the Refill rinse aid message appears, the reservoir contains sufficient rinse aid for 2 - 3 programs only.
Add rinse aid.
Press the center button to confirm.
The rinse aid refill indicator will go out.
Add rinse aid only until it is visible in the opening.
The rinse aid reservoir holds approx.
4 oz (110 ml).
Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a program.
24
Loading the dishwasher
Preparing the load
Remove coarse food residues from the dishware.
There is no need to rinse items under running water!
Tips
Ensure that no acid or solvent residues, especially hydrochloric acid or chlorides, get inside the machine.
Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher.
These substances will damage the dishwasher.
Dishware can be loaded anywhere in the baskets, but the following notes should be observed:
Load the dishware so that water can access all surfaces. This ensures that the items will be properly cleaned.
Load plates symmetrically in the upper and lower baskets with the concave surfaces facing the center of the basket (as shown on the following pages).
Do not place dishes or cutlery inside other pieces. They will cover one another.
Load the dishware so that water can access all surfaces. This ensures that the items will be properly cleaned.
Make sure that all items are securely positioned.
Hollow items such as cups, glasses and pans, etc. should be placed upside down in the baskets.
Tall and narrow hollow items should be placed in the center of the basket if possible to ensure better water coverage.
Concave items such as mugs or bowls should be placed at an angle so that the water can run off.
The spray arms must not be blocked by items which are too tall or hang through the baskets. When in doubt, test for free movement by manually rotating the spray arms.
Small items can fall through the holders in the baskets. Small items should therefore be placed in the cutlery basket or cutlery tray
(depending on model).
Some foods may contain natural dyes, e.g. carrots, tomatoes or ketchup. Plastic items in the dishwasher may discolor if large quantities of these foods find their way into the dishwasher on the dishes. The stability of plastic items is not affected by this discoloration.
25
Loading the dishwasher
Items not suitable for dishwashers:
– Wooden cutlery and cookware or items with wooden parts: these may discolor and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher.
– Craft items, antiques, valuable vases and decorative glassware: such items are not suitable for dishwashers.
– Plastic items which are not heat resistant: the high temperatures in the dishwasher may cause them to melt or lose shape.
– Copper, brass, tin and aluminum items: these may discolor or become matt.
– Colors painted over a glaze: these may fade after a number of washes.
– Delicate glassware and glassware containing lead crystal: clouding may occur over time.
We recommend
– When purchasing new cookware and cutlery, make sure they are dishwasher-proof.
– Clouding may occur on glasses after frequent washing. If delicate glassware is washed in the dishwasher ensure that only a special glass-care program with very low temperatures (see program chart) is selected and that suitable detergent is used. This will reduce the risk of clouding.
Please note:
Silver and aluminum which has been in contact with foods containing sulfur can discolor.
Aluminum components (e.g.
grease filters) must not be cleaned with caustic alkaline commercial or industrial cleaning agents.
These may damage the material, or in extreme cases, there is a risk of a severe explosive chemical reaction
(such as an explosive oxyhydrogen gas reaction).
26
Example of load with 10 place settings with cutlery tray
Loading the dishwasher
Lower basket
Upper basket
Cutlery tray
27
Cutlery tray
28
Loading the dishwasher
Example of load for 16 place settings with cutlery tray
Upper basket
Lower basket
Upper basket
For safety reasons, do not operate the dishwasher without the upper and lower baskets in place.
Loading the dishwasher
Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc. Shallow pans or casserole dishes can also be placed in the upper basket.
Long items such as soup ladles, mixing spoons and long knives should be placed horizontally across the front of the upper basket.
Hinged spikes
The rows of spikes can be folded down to make more room for larger items such as casserole dishes.
Press the yellow lever downwards , and then lower the spikes .
Cup rack
Raise the rack to make room for tall items.
Glasses can be arranged along the positioning rail of the cup rack to give them some support during the program.
Lower the cup rack and lean the glasses against it or double stack smaller pieces.
29
Loading the dishwasher
XXL cup rack
The cup rack can be set at two different widths so that it can also accommodate large cups.
You can also move one of the side inserts of the cutlery tray to make more room for tall glasses.
Adjusting the height of the glass rail:
You can set the glassware rail at two different heights.
Pull the cup rack upwards and click it back into position at the required width.
Glass rail
This rail is designed to hold tall glasses and stemware securely.
Pull the rail upwards and click it back into position at the required height.
Use the lower position for small glasses and tumblers.
Use the higher position for tall glasses and glasses with stems.
Lower the rail and lean tall glasses against it.
30
Adjusting the upper basket
In order to gain more space for individual taller pieces of tableware in the lower or upper basket, the upper basket can be adjusted on three levels with 3/4" (2 cm) between each level.
The upper basket can also be set at an angle with one side high and the other side low to improve water drainage.
However, make sure that the basket can slide smoothly in and out of the chamber.
Pull the upper basket out.
Loading the dishwasher
Depending on the setting of the upper basket, the following plate dimensions can be accommodated.
Dishwasher with a cutlery tray
Upper basket adjustment
Upper
Middle
Lower
Plate Ø
Upper basket
7 1/2"
(19 cm)
8 1/4"
(21 cm)
9 1/16"
(23 cm)
Lower basket
12 1/4"
(31 cm)
11 7/16"
(29 cm)
10 5/8"
(27 cm)
To raise the upper basket:
Lift the basket until it clicks into place.
To lower the upper basket:
Pull upwards on the levers at either side of the upper basket.
Adjust the basket to the desired height and then push the levers securely back down into position.
31
Loading the dishwasher
Lower basket
Use the lower basket for larger and heavier items such as plates, serving platters, saucepans, serving dishes, etc. Glasses, cups and small items such as saucers can also be placed in the lower basket.
Place very large plates in the center of the lower basket.
When tilted, plates up to 13
3/4" (35 cm) in diameter can be accommodated.
Dishwasher with cutlery tray
Heavily soiled items
32
Loading the dishwasher
Removable MultiComfort insert
The rear section of the lower basket is used for washing cups, glasses, plates and pots.
You can remove the MultiComfort insert to make more room for larger items such as pans and casserole dishes.
Glass rack
The glass holder can be raised to make more room for tall items.
Stemware, e.g. wine glasses or champagne flutes, can be leaned against the glass rack or suspended from it.
The height of the glass rack is adjustable.
To remove the insert
Pull the yellow handle forwards and remove the insert.
To replace the insert
Fit the insert into the lower basket with the hooks under the long crosspiece.
Press down on the insert until it clicks into position.
Slide the glass rack to the desired height until the catches click into place at the top.
33
Loading the dishwasher
Glass rail
This rail is designed to hold tall glasses and stemware securely.
Press the yellow lever downwards , and then lower the spikes .
Bottle holder
The bottle holder can be used to wash narrow items, e.g. milk and baby bottles.
Lower the rail and lean tall glasses against it.
Hinged spikes
The spikes at the front are used for washing plates, soup bowls, platters, dessert bowls, and saucers.
The spikes can be lowered to make more room for large items, e.g. pots, pans and dishes.
If the bottle holder is not needed, lift it up and fold the sides down , as illustrated.
34
3D cutlery tray
Loading the dishwasher
Arrange the cutlery in the tray as shown.
To make unloading easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs off them freely.
The upper spray arm must not be blocked by items which are too big
(e.g. very large platters).
If spoon handles do not fit between the holders, then lay them the other way around.
The side sections of the tray can be moved into the middle to accommodate individual taller items of tableware in the upper basket.
You can use the yellow slide to adjust the height of the middle section of the cutlery tray to make more room for large items of cutlery, such as serving spoons and ladles.
35
Optional accessories
Making better use of the dishwasher
Optional accessories for this dishwasher are available from Miele.
If you would like to …
... wash a Miele Cappuccinatore
...wash additional cutlery
...wash long-stemmed glassware you will need to order …
… a Cappuccinatore insert for the upper basket
... a cutlery basket for the lower basket
...a glass rail for the lower basket
36
Operation
Detergent
Powder detergents
Use powder detergent or detergent tabs only in the door dispenser compartment.
Suitable products are available from
Miele Professional.
Detergent tabs can be used.
Only use detergent tabs that are quick dissolving. Suitable detergent tabs are available from Miele
Professional.
Add powder detergent or detergent tabs to the detergent compartment.
Detergent dosage
Unless directed otherwise, use one detergent tab or add 20 to 25 g detergent to compartment II, depending on the level of soiling.
With very heavy soiling, you can also add a small amount of detergent to compartment l (see "Program chart").
Failure to use the recommended amount of detergent may adversely affect the cleaning results.
Liquid detergent
This dishwasher can be fitted with an external dispenser pump for liquid detergent (DOS module).
See "Settings menu - External DOS" to activate the dispenser pump and set the detergent dosage.
For special soiling or if using liquid detergent, dispensed by a liquid detergent pump, contact Miele for advice on how to adapt the detergent dosage to the particular circumstances.
Detergents containing active chlorine must not be used.
They can damage plastics and elastomers in the dishwasher.
Refilling or changing containers
The DOS module is equipped with a level indicator which gives the Add detergent
message in the display when the level drops below the minimum.
As soon as the message appears in the display, refill or replace the container with a full one at the end of the program.
Confirm the message with the OK button.
Replace the container in time to prevent the dispensing system from being emptied completely.
An empty dispensing system must be vented before the next program is started.
37
Operation
Place the container on the open dishwasher door or on a surface which is easy to clean.
Unscrew and remove the siphon.
Place the siphon on the open dishwasher door.
Replace the empty container with a full one.
Push the siphon into the opening of the container and screw it on tightly.
Be sure to observe the color coding.
Wipe up any spilled neutralizing agent thoroughly.
Place the container on the floor next to the dishwasher or in an adjacent cupboard. The container must be on the same level as the dishwasher. It must not be placed higher than the dishwasher or on top of it.
The DOS system must then be vented.
To vent the system and adjust the dosage amount, see
"Settings menu, External DOS".
Checking consumption
Monitor the amount of process chemicals used by regularly checking the level in the container in order to detect any dispensing irregularities.
Dispensing system maintenance
To ensure that the dispensing system functions reliably it should be serviced at specified intervals. This work should only be performed by Miele Service.
The DOS module dispensing hoses must be replaced at 1 - 1
1
/
2
yearly intervals.
Whether you use powder or liquid detergent, always observe the manufacturer's instructions.
38
Operation
Avoid inhalation of powder detergents and do not ingest dishwasher detergent. Detergents can cause chemical burns in the nose, mouth and throat. Seek medical advice immediately if detergent has been swallowed or inhaled. Keep detergent and other household agents out of the reach of children at all times. Keep children away from the dishwasher when the door is open. There could still be detergent residues in the chamber.
To avoid the danger of children coming into contact with the dishwasher detergent, only add detergent just before starting the program and close the door, activating the safety lock.
Adding detergent
Add the required amount of detergent and close the flap.
Make sure that the detergent packaging is properly closed after use to avoid it getting damp and becoming lumpy.
Dispensing aid
Compartment I holds max. 0.3 oz.
(10 ml),
Compartment II holds max. 1.7 oz.
(50 ml) of detergent.
There are markings to assist with dispensing: 20 and 30. The marks indicate a level of approx. 20 or 30 ml when the door is open in the horizontal position.
They also indicate the approx. level in grams (depending on the manufacturer and the coarseness of the agent).
Press the opening catch on the detergent dispenser. The flap will spring open.
The flap is always open at the end of a program.
39
Operation
Switching on the appliance
Turn on the water supply if it is turned off.
Make sure the spray arms are not obstructed.
Close the door.
Switch the dishwasher on with the button.
The factory-set Normal program will appear in the display and the matching indicator light will come on.
After a short while, the estimated program duration for the selected program will appear in the display.
You can also change the setting to the program you last used (see "Settings menu, Program selection").
Selecting a program
Choose your program according to the type of load and how dirty it is.
The different programs and their uses are described in the Program chart later on in this booklet.
Select the program required with the
button.
The indicator light next to the program selected will come on.
When the indicator light next to lights up, you can select further programs by means of the > button.
You can now select additional functions (see "Additional functions").
Starting a program
Start the program by closing the door.
The In-operation indicator comes on to show that a program has been started.
If any additional functions are selected, the appropriate indicators will also light up.
A program should only be cancelled in the first few minutes, if at all.
Important program stages (e.g.
reactivating the water softener) could otherwise be omitted.
40
Operation
Time display
Before the program starts, the display shows the duration of the selected program in hours and minutes. The remaining runtime is displayed during the program.
Each program phase is indicated by a symbol:
Pre-rinse
Main wash
Interim rinse
Final rinse
Drying
Finished
The displayed program duration may vary with the same program. It is influenced by, among other things, the temperature of the incoming water, the reactivation process of the water softener and the amount of dishes.
When a program is selected for the first time, the display shows an average program duration for warm water.
The program duration changes if the electrical connection is changed.
Standby
To save energy, the dishwasher will switch to Standby mode a few minutes after the last time a button has been pressed or a few minutes after the end of the program. The display and the indicator lights will go out and only the
indicator will flash slowly.
Press the button to switch the display and indicator lights back on.
If the dishwasher is not switched off at the end of the program, it will switch off completely after a few minutes in
Standby mode (see "Settings menu,
Optimize standby").
The dishwasher will not switch to
Standby mode while a program is running, if salt or rinse aid needs to be replenished or there is a fault.
You can switch off the refill indicators to replenish salt and rinse aid so that the dishwasher will go into Standby despite a lack of salt or rinse aid (see
"Settings menu, Refill display").
You cannot switch off fault messages.
41
Operation
End of program
At the end of a program, the Inoperation indicator light will be visible flashing slowly with the door shut.
The program has finished when End or
AutoOpen
appears in the display and the door has opened slightly (if applicable).
If Extra Drying was selected and
AutoOpen is active, the drying fan will run for a few minutes after the program has ended.
Open the door completely to reengage the door closing mechanism.
You can now empty the dishwasher.
The In-operation indicator light will go out 10 minutes after the end of the program if the door is closed.
If you have deactivated the automatic door opening function (see
"Settings menu, AutoOpen "), but would still like to open the door at the end of the program, then make sure that you open the door fully.
Otherwise steam from the dishwasher could damage the edge of the counter because the fan is no longer running.
Switching off
At the end of a program:
Open the door.
Turn the dishwasher off with the button.
The dishwasher will continue to use electricity until it is switched off with the button.
Tip: If the dishwasher is not going to be used for a longer period of time, e.g., while on vacation, the water supply should be turned off.
Unloading the dishwasher
Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are cool enough to handle before unloading them.
The dishes will cool much faster if you open the door when the program has ended.
Unload the lower basket first, then the upper basket and then the cutlery tray
(depending on model).
This will prevent water from the upper basket and cutlery tray from dripping onto dishes in the lower basket.
42
Operation
Interrupting a program
A program is interrupted as soon as the door is opened.
If the door is closed again, the program will continue from the point it was at before the door was opened.
Water in the dishwasher may be hot. Danger of scalding.
Only open the door if absolutely necessary and exercise extreme caution when doing so. Before closing the door again, leave it ajar for approx. 20 seconds. This will enable the temperature in the wash chamber to settle. Then raise the door up and push until the catch engages.
Changing a program
If the detergent dispenser flap has already opened, powder detergent must be added for the new program unless liquid detergent is being dispensed.
If a program has already started and you wish to change it, proceed as follows:
Open the door.
Turn the dishwasher off with the button.
Switch the dishwasher on with the button.
Select the program required with the program selector button.
Start the program by closing the door.
The In-operation indicator comes on to show that a program has been started.
43
Program chart
Program Application
ProSpeed
Universal
For fresh, non-sticky food residues.
For normal, slightly dried food residues.
Pots & Pans
For burnt-on, stubborn, dried-on food deposits containing starch or protein
1)
.
China &
Crystal
Special glassware program.
Sanitize
Special hygiene program for items that need to be hygienically clean
Detergent
The following dosages are based on Miele cleaning agents.
Please follow manufacturer's instructions on dosage.
Compartment I
1)
Compartment II
1)
20 - 25 g or 1 tab
10 g
20 - 25 g or 1 tab
20 - 25 g or 1 tab
20 - 25 g or 1 tab
20 - 25 g or 1 tab
Plastics
Special plastics program 20 - 25 g or 1 tab
Glass no rinse aid
Normal
*)
Special program for beer glasses. (Instead of being left to dry in the machine at the end of the program, beer glasses are taken out and dried by hand).
Program for completely washing a full load of normally soiled dishware.
Energy-saving program with a long running time.
Rinse & Hold
To rinse heavily soiled items, e.g. for initial removal of soil or to prevent residues drying on to dishes when a complete program does not yet need to be run.
20 - 25 g or 1 tab
20 - 25 g or 1 tab
*) This program is the most efficient in terms of energy and water consumption for washing normally soiled tableware.
(Program sequence cannot be altered)
1)
see "Operation - Detergent"
44
Program chart
Program cycle
Pre-rinse
X
8 min
X
8 min
X
10 min
Clean
X
150°F
(65°C)
1 min
X
150°F
(65°C)
10 min
X
165°F
(75°C)
10 min
X
120°F
(50°C)
1 min
X
167°F
(75°C)
10 min
X
120°F
(50°C)
1 min
X
120°F
(50°C)
1 min
X
118.4°F
(48°C)
47 min
X
Cold
8 min
Interim rinse I
X
10 s
X
3 min
X
3 min
X
3 min
X
3 min
X
5 min
X
3 min
Interim rinse II
2)
(X)
(X)
(X)
(X)
(X)
Final rinse
X
150°F
(65°C)
3)
30 s
X
150°F
(65°C)
3)
1.5 min
X
150°F
(65°C)
3)
1.5 min
X
120°F
(50°C)
1 min
X
158°F
(70°C)
3)
3 min
X
140°F
(60°C)
30 s
X
-
5)
1 min
X
125.6°F
(52°C)
5 min
Drying
X
30 min
X
45 min
X
45 min
Additional drying
(X)
(X)
(X)
(X)
X = sections included in a program
(X) = optional sections which can be selected (see "Additional functions")
2)
Interim rinse II must be programmed by a Miele service technician.
3)
Optional temperature increase to 165°F (75°C).
4)
No AutoOpen at the end of the program because of the short running time.
5)
Without rinse aid and with cold water.
Auto-
Open
4)
(X)
(X)
(X)
(X)
(X)
(X)
Water plus
(X)
(X)
(X)
(X)
(X)
45
Program chart
Program
Consumption
6)
Cold water
60°F (15°C)
Energy
Hot water
130°F (55°C)
1.5 kWh 0.9 kWh
ProSpeed
Universal
Pots & Pans
China &
Crystal
Sanitize
1.6 kWh
1.9 kWh
1.0 kWh
2.0 kWh
1.0 kWh
1.0 kWh
0.4 kWh
1.1 kWh
Water
17 l
17 l
23 l
17 l
23 l
Duration
6)
Cold water
60°F (15°C)
22 min
7)
Hot water
130°F (55°C)
17 min
7)
35 min
7)
52 min
7)
22 min
7)
30 min
46 min
18 min
7)
7)
7)
86 min 80 min
Plastics
Glass no rinse aid
1.3 kWh
0.7 kWh
0.5 kWh
0.4 kWh
23 l
17 l
83 min
19 min
76 min
17 min
Normal
*)
1.059 kWh 0.6 kWh 17 l 182 min 169 min
Rinse & Hold 0.03 kWh 0.03 kWh 6.5 l 11 min 11 min
6)
The values listed were determined in accordance with EN 50242 for a connected load of
8.3 kW. In actual practice, there may be significant differences because of different conditions.
The duration shown adjusts to your household conditions.
7)
The value is based on the wash time without drying.
46
Additional functions
Additional drying
For better drying results and to reduce the amount of steam that escapes when the door is opened, the "Extra
Drying" function extends the fan runtime at the end of the program. This function is not available for all programs
(see "Program chart").
When Extra Drying is selected, the program duration will increase by approx. 20-30 minutes, depending on the program.
Open the door.
Switch the dishwasher on with the button.
The indicator will light up.
Select a program.
Press the button.
The "" indicator light will come on if the option is available for the program selected.
Start the program by closing the door.
Delay start
The start time of a program can be delayed. A delay start time of between
30 minutes and 24 hours can be selected. The delay start time is set in
30 minute steps.
When using the delay start function, make sure that the detergent compartment is dry before adding detergent. Wipe dry with a cloth if necessary.
If the compartment is wet, cleaning agent can become lumpy and stick to the dispenser, with the result that it is not fully dispensed.
Open the door.
Turn the dishwasher on using the button.
The indicator will light up.
Select the program required with the program selector button.
Press the button.
The last delay start time will appear in the display. The indicator will light up.
Set the required time using the button.
If you keep the Delay start button pressed in, the time will increase automatically up to 24:00 h . To start at
30 minutes again, press the button twice.
Close the door.
47
Additional functions
If you do not close the door within a few seconds of setting the delay start time, the program duration will appear in the display again. You will have to set the delay start time again.
The time starts counting down in minutes until the program start time.
At the end of the delay period, the program selected begins automatically.
The In-operation indicator lights up.
Starting a program before the delay start time has elapsed:
A program can be started before the delay start time has elapsed. Proceed as follows:
Open the door.
Turn the dishwasher off with the button.
Switch the dishwasher on with the button.
Select the program required with the program selector button.
Start the program by closing the door.
The In-operation indicator comes on to show that a program has been started.
ClearView Lighting
This dishwasher has interior lighting.
When the door is open the lighting will switch off automatically after 15 minutes.
You can also switch off the interior lighting permanently.
Half open the dishwasher door and quickly swing it back and forth three times. When doing this, open the door wide enough for the interior lighting to switch on and off.
The interior lighting has been switched off permanently.
To switch the lighting back on again, quickly swing the half-opened door back and forth three times again.
48
Settings menu for changing standard settings
Open the Settings menu
If the dishwasher is switched on, switch it off with the button.
Keep the button pressed in.
Switch the dishwasher on with the
- button and hold the button down for at least 4 more seconds.
The first option of the Settings menu will appear in the display and all the indicator lights will come on.
See "Guide to the appliance, Display" for more information about the display and controls.
Select the menu option you wish to change.
Submenu options which have already been set are marked with a check .
Settings menu
Language
The display can be set to appear in one of several different languages.
You can change the language in the display via the Language submenu.
Select the desired language and press the center button to confirm.
The flag after the word Language acts as a guide if a language which you do not understand has already been set.
If this the case, keep selecting the menu option which has a flag after it until you reach the Language submenu.
49
Settings menu
Water hardness
Your dishwasher is fitted with a water softener assembly. The dishwasher must be programmed for the water hardness in your household connection.
– The dishwasher must be programmed to match exactly the hardness of your water.
– Your local water supplier can tell you the water hardness level in your area.
– Where the water hardness fluctuates, e.g. between 18 - 26 gr/gal (17 -
25 °d - German scale), always program the dishwasher to the higher value (26 gr/gal or 25 °d in this example).
Select the hardness of your water and press the center button to confirm.
A check will appear beside the water hardness which has been set.
16
17
18
19
20
21
13
14
15
9
10
11
12
6
7
8
4
5
2
3
°d
1
33
34
35
29
30
31
32
26
27
28
22
23
24
25
36
50
16
17
18
19
20
21
13
14
15
9
10
11
12
6
7
8
4
5
2
3
Display
1
33
34
35
29
30
31
32
26
27
28
22
23
24
25
36
16
17
18
19
20
21
13
14
15
9
10
11
12
6
7
8
4
5
2
3 gr/gal
1
34
35
36
30
31
32
33
27
28
29
22
23
25
26
37
Settings menu
Rinse aid
For best results, the rinse aid dosage can be adjusted.
The dosage can be set between approx. 0-6 ml.
The factory setting is 3 ml of rinse aid.
If spots appear on dishware and glassware:
– Increase the rinse aid dosage.
If clouding or smearing appears on dishware and glassware:
– Decrease the rinse aid dosage.
Select the desired amount of rinse aid and press the center button to confirm.
Buzzer
When the buzzer is activated, an audible tone sounds at the end of a program and when there is a fault.
Buzzer at end of program
You will hear the buzzer at the end of a program in bursts of four with a short pause in between. The buzzer will continue to sound for up to an hour if you do not switch the dishwasher off.
Buzzer when there is a fault
In the event of a fault, the buzzer will sound four times in intervals with only a very short pause in between.
The buzzer which sounds when there is a fault cannot be deactivated.
Setting the buzzer volume
There are seven different volume settings. If no volume is selected, the buzzer is deactivated.
Select the desired volume and press the center button to confirm.
51
Settings menu
AutoOpen
To improve drying, the door automatically opens a little at the end of a program, except for Pre-rinse,
ProSpeed and Glass no rinse aid (see
Program guide).
With the Universal, Intensive and
Glasses program, AutoOpen can only be activated by selecting Extra Drying
(see "Additional functions, Extra drying").
With the Normal program the door opens during the drying phase.
This function can be deactivated if wished.
Select the desired setting and press the center button to confirm.
If you have deactivated the automatic door opening function but would still like to open the door at the end of the program, make sure that you open the door fully.
Otherwise steam from the dishwasher could damage the edge of the counter because the fan is no longer running.
Optimize Standby
To save energy, the dishwasher will switch to Standby mode a few minutes after the last time a button has been pressed or a few minutes after the end of the program. The display and indicator lights will go out and only the
indicator light will flash slowly.
If the dishwasher is not turned off at the end of the program, it will switch off completely after a few minutes in
Standby mode.
Optimize Standby can be switched off if you prefer. If you do this, the display and indicator lights will not go out and the duration before the dishwasher switches off automatically increases to approx. 6 hours.
Doing this will increase energy consumption.
Select the desired setting and press the center button to confirm.
The dishwasher will not switch to
Standby mode while a program is running, if salt or rinse aid needs to be replenished or there is a fault.
52
Refill indicators
You can switch off the refill indicators to replenish salt and rinse aid so that the dishwasher will go into Standby despite a lack of salt or rinse aid.
You cannot switch off fault messages.
If you want the dishwasher to switch to
Standby mode in spite of the refill indicators, you can switch both indicator lights off.
Select the desired setting and press the center button to confirm.
Brightness
There are seven different display brightness settings.
Select the level of brightness you want and press the center button to confirm.
Contrast
There are seven different display contrast settings.
Select the contrast you want, and press the center button to confirm.
Settings menu
Filter check
You can adjust the interval at which the message to remind you to check the filters appears.
You can set an interval between 30 and
60 program cycles.
The "Check filters" message is set at the factory to appear after every 50 program cycles.
This function can be deactivated if wished.
Select the desired setting and press the center button to confirm.
53
Settings menu
Detergent quantity
This function only becomes visible when External DOS is activated.
When using liquid dispensing via an external dispensing module, you can dispense the detergent according to the detergent manufacturer's instructions in milliliters or as a percentage.
– Value in ml
30 ml is set as standard. The dispensed quantity can be modified between 10 and 100 ml in 2 ml steps.
–
Value in %
0.50 % is set as standard. The dispensed quantity can be modified between 0.17 and 1.67 % in 0.03 -
0.04 % steps.
Setting the dosage:
Set the dosage according to the detergent manufacturer's recommendations.
The dishwasher uses approx. 6.5 l of water for the main wash cycle.
Example:
The detergent manufacturer recommends 4 ml (or 0.07 %) of detergent per liter of water.
6.5 l x 4 ml/l = 26 ml.
(6.5 l x 0.07 %/l = 0.455 %)
Select the desired amount of detergent or dosage concentration and press the center button to confirm.
Venting DOS
The DOS system will not dispense reliably if there is air in the system.
The DOS system must be vented:
– it is being used for the first time,
– if the liquid cleaning agent reservoir was not refilled in time and the DOS system was emptied,
– if the detergent canister was replaced,
To ensure that the dispensing system functions properly, prior to venting make sure that the detergent container is full enough and that the dispensing lances are firmly attached to the containers.
Select
Start venting
and press the center button to confirm.
The venting process begins. The remaining time appears in the display.
The "Pre-rinse" program is offered directly after the venting process is finished. Start the program in order to dilute and drain any detergent that escaped into the wash chamber.
54
High-temperature final rinse
For better drying, the rinse temperature can be increased for individual programs. This function is not available for all programs (see "Program chart").
Select the desired setting and press the center button to confirm.
Water plus
When Water plus is selected, more water will be used for the wash cycle.
This function is not available for all programs (see "Program chart").
Select the desired setting and press the center button to confirm.
Program selection
You can chose whether to preset the
Normal program or the last selected program when the dishwasher is switched on.
Select the desired setting and press the center button to confirm.
Settings menu
Showroom program
For demonstration purposes only!
The dishwasher is equipped with various demo programs for showroom use.
– Demo with sound :
This program activates the circulation pump to demonstrate the sound of the dishwasher.
– Demo AutoOpen :
The door will open automatically.
To switch Demo mode on
Select the desired option.
Select
On and press the center button to confirm.
Close the Settings menu.
Close the door.
The demo mode is activated.
To switch Demo mode off
Demo mode ends automatically after one cycle.
55
Settings menu
Factory default setting
If any settings have been changed from the factory default, you can reset them back to the factory default settings.
An activated external dispensing module and its respective amount of detergent or dosage concentration will not be reset.
Select
Reset
and press the center button to confirm.
To close the Settings menu
You can exit the Settings menu using
Close menu .
Select
Close menu
and press the center button to confirm.
The last selected program will appear briefly in the display and the appropriate indicator light will come on.
After a short while, the estimated program duration will be displayed.
56
Cleaning and care
Maintenance
In order to increase the dishwasher's service life, the machine should be served by an authorized Miele service technician after every 750 hours of operation or at least once a year.
This service work covers the following points:
– Electrical safety check
– Door mechanism and door seal
– Screw connectors and connections in the wash cabinet
– Water intake and drainage
– Internal and external dispensing systems
– Spray arms
– Filter combination
– Collecting basin with drain pump and non-return valve
– All baskets and inserts
As part of the service package, the following functional checks are performed:
– Test run of a program cycle
– Thermoelectric measurement
– Leak test
– Check of all safety-relevant measuring systems (indication of fault status)
– Safety features check
All surfaces of this appliance are susceptible to scratching.
Contact with unsuitable cleaning agents can alter or discolor all surfaces.
Cleaning the wash chamber
The wash chamber is largely selfcleaning, provided that the correct amount of detergent is always used.
If, despite this, lime scale or grease deposits accumulate in the chamber, these can be removed with a proprietary dishwasher cleaner
(available from Miele).
Washing at low temperatures can allow germs and odors to build up inside the appliance. To prevent this, run an intensive program with detergent after approx. 20 program cycles with low temperatures.
Cleaning the door and the door seal
Wipe the door seals regularly with a damp cloth to remove food deposits.
When the dishwasher is being loaded, food and drink residues may drip onto the sides of the dishwasher door. These surfaces are outside the wash chamber and are not accessed by water from the spray arms. Any soiling should be wiped off these surfaces before the door is closed.
57
Cleaning and care
Cleaning the indicator reflector panel
The indicator reflector panel for the Inoperation indicator light is situated in the cover plate underneath the counter.
The indicator reflector panel should only be wiped with a damp cloth or a suitable cleaning agent designed for use on plastic.
Cleaning the control panel and door front
Remove any soiling immediately.
If soiling remains longer, the surfaces can become discolored or changed.
The control panel should only be wiped with a damp cloth.
Clean the front with a clean sponge and a solution of hot water and liquid dish soap. After cleaning, dry with a soft cloth.
A clean, damp microfiber cloth without cleaning agent can also be used.
To avoid damaging the surfaces of the machine, do not use:
– cleaning agents containing soda, ammonia, acids or chlorides,
– lime scale removers,
– abrasive cleaning products, such as scouring powder, scouring liquid, or pumice stones,
– solvent-based cleaning agents,
– stainless steel cleaners;
– dishwasher cleaners;
– oven sprays;
– glass cleaner;
– hard, abrasive sponges and brushes, such as pot scrubbers,
– eraser sponges,
– sharp metal scrapers,
– steam cleaning appliances.
58
Cleaning and care
Filter system
The filter combination in the base of the wash chamber prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects.
This dishwasher must not be used without all the filters in place!
Collection of coarse soil may cause the filters to clog. The level of soiling and time it takes before the filters need cleaning will vary depending on use.
The message Check filters will appear in the display after every 50 program cycles (factory default setting).
You can turn off the filter check or set the interval for this message to appear between 30 to 60 program cycles (see
"Settings menu, Check filter").
Check the filter combination.
Clean it if necessary.
Confirm the message with the center button.
The last selected program will appear briefly in the display and the appropriate indicator light will come on.
After a short while, the estimated program duration will be displayed.
Cleaning the filters
Turn the dishwasher off.
Turn the handle counterclockwise to release the filter combination
Lift the filter combination out of the dishwasher . Remove any coarse particles and rinse the filter well under running water. Use a nylon brush if necessary.
Make sure that when cleaning the filters, no coarse soil falls into the circulation system,
This could cause a blockage.
59
Cleaning and care
To clean the inside of the filter, the flap must be opened:
Press catches together in the direction of the arrows as shown, and open the filter .
Rinse all of the filters under running water.
Then close the flap so that the catch engages.
Replace the filter combination so that it lies flat in the base of the wash chamber.
Then turn the handle clockwise until both arrows point towards each other. This will lock the filter combination in place.
When you are fitting the filter combination, take care that it is secured in position correctly.
Otherwise, coarse soil could get into the circulation system and cause a blockage.
60
Cleaning and care
Cleaning the spray arms
Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months).
Turn the dishwasher off.
Remove the spray arms as follows:
Take out the cutlery tray (if your dishwasher is fitted with one).
Pull the lower spray arm firmly upwards to remove it.
Push the top spray arm upwards to engage the inner ratchet. Then unscrew the spray arm.
Push the middle spray arm in to engage the ratchet. Then unscrew spray arm .
Remove the lower basket.
Use a pointed object to push food particles that are stuck in the spray arm jets into the spray arm.
Rinse the spray arms thoroughly under running water.
Replace the spray arms and check that they rotate freely.
61
Frequently asked questions
With the help of the following guide, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be corrected without contacting the Service Department.
Repairs must only be carried out by a Miele technician or a Mieleauthorized service agent in accordance with local and national safety regulations. Unauthorized or incorrect repairs and other work by unqualified persons could be dangerous.
Technical problems
Problem
The dishwasher does not start.
The dishwasher stops during a program.
One of the following fault messages is displayed:
After the program has started, the Inoperation indicator light is not visible.
The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following faults appears in the display:
Possible cause and solution
The door is not properly closed.
Push the door firmly shut.
The dishwasher is not plugged in.
Insert the plug.
The circuit breaker has tripped.
Reset the circuit breaker (see data plate for the correct fuse rating).
The dishwasher is not switched on.
Press the button and select a program.
The circuit breaker has tripped.
Reset the circuit breaker (see data plate for the correct fuse rating).
If the circuit breaker trips again, contact Miele
Customer Service.
Before remedying the fault:
Turn the dishwasher off using the button.
The indicator reflector panel was not correctly fitted.
Refit the indicator reflector panel correctly (see the installation plan).
Before remedying the fault:
Turn the dishwasher off using the button.
62
Problem
Fault FXX
Waterproof
Frequently asked questions
Possible cause and solution
There may be a technical fault.
After a few seconds:
Turn the dishwasher back on.
Select the desired program.
Close the door.
If the fault message is displayed again, there has been a malfunction.
Contact Miele Service.
The Waterproof system was activated.
Close the water supply valve.
Contact Miele Service.
63
Frequently asked questions
Faults with water intake or drainage
Problem
The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following faults appears in the display:
Possible cause and solution
Open water supply
The water supply is turned off.
Open the water supply valve all the way.
Water intake
Before remedying the fault:
Turn the dishwasher off with the button.
There is a problem with the water intake.
Open the water supply valve all the way.
Check the water inlet filter and clean it if necessary
(see "Maintenance").
The water pressure at the intake is lower than 4.35
psi (0.3 bar).
Contact a plumber.
Drain
Before remedying the fault:
Turn the dishwasher off with the button.
The water outlet is restricted.
There might be water in the wash chamber.
Clean the filter combination (see "Cleaning and care").
Clean the drain pump (see "Frequently asked questions").
Clean the non-return valve (see "Frequently asked questions").
Remove any kinks or high loops in the drain hose.
64
Frequently asked questions
General problems with the dishwasher
Problem
The indicator lights and the display are dark.
Only the indicator flashes slowly.
Possible cause and solution
The indicators and the display switch off automatically to save energy (Standby mode).
Press the button. Standby comes to an end.
The interior lighting does not switch on when the door is opened.
The following fault is shown in the display:
Salt container lid
During the program the warning buzzer is also sounding and the In operation indicator light is flashing.
The following fault message appears in the display during a program:
Spray arm blocked
Detergent residue is left in the detergent compartment at the end of a program.
The detergent dispenser flap cannot be closed.
The inside of the door and/or the interior walls are wet after a program has finished.
The interior lighting has been switched off.
Switch the lighting back on again (see "Additional functions, ClearView Lighting").
The salt reservoir cover is not properly closed.
Close the salt reservoir cover.
If the salt reservoir cover opened during a program:
Switch the dishwasher off and then on again with the button.
Start the program again.
The middle spray arm is blocked by individual dishes.
Open the dishwasher door and rearrange the items which are obstructing the spray arm.
The spray arm jets of the middle arm are clogged.
Turn the dishwasher off with the button.
Then:
Clean the spray arm (see "Cleaning and care").
The detergent compartment was still damp when detergent was added.
Make sure the compartment is dry before adding detergent.
Detergent residue is blocking the latch.
Remove the detergent residue.
This is not a fault.
It is caused by the drying system.
The moisture will dissipate after a short while.
65
Frequently asked questions
Problem
Water remains in the wash chamber at the end of a program.
Some programs run for a long time.
Although AutoOpen has been selected, the door remains closed at the end of ProSpeed and the dishes are still moist.
Possible cause and solution
Before remedying the fault:
Turn the dishwasher off with the button.
The filter combination in the wash chamber is clogged.
Clean the filter combination (see "Cleaning and care").
The drain pump or non-return valve is blocked.
Clean the drain pump or the non-return valve (see
"Frequently asked questions").
The drain hose is kinked.
Remove the kink.
This is not a fault.
Some special programs have long running times.
Select a different program (see "Program chart").
This is not a fault.
The AutoOpen function is not available with the
ProSpeed program due to its short duration.
To improve the drying, raise the rinse temperature
(see "Setting menu - High temp rinse").
66
Frequently asked questions
Noises
Problem
There is a knocking noise in the wash cabinet.
There is a rattling noise in the wash cabinet.
There is a knocking noise from the water pipe
Possible cause and solution
A spray arm is hitting the dishware.
Interrupt the program, and rearrange the items which are obstructing the spray arm.
Dishware is moving around in the wash cabinet.
Interrupt the program and rearrange loose pieces.
A foreign object (e.g. a cherry pit) has become lodged in the drain pump.
Remove the foreign object from the drain pump
(see "Cleaning the drain pump and non-return valve").
This may be caused by the installation or the diameter of the water pipe.
This has no effect on the functioning of the dishwasher.
If in doubt, contact a plumber.
67
Frequently asked questions
Poor cleaning results
Problem
The dishes are not clean.
Smearing appears on glassware and cutlery.
There is a bluish sheen on the surface of glassware; film can be wiped off.
Dishware is not dry or cutlery and glasses are spotty.
Possible cause and solution
The dishes were not loaded correctly.
See notes in "Loading the dishwasher".
The program was not suitable for the requirements.
Select a more suitable program (see "Program guide)".
Not enough detergent was dispensed.
Increase the dosage.
The detergent used is not suitable for the type of soiling present.
Switch to another detergent.
Items are blocking the path of the spray arms.
Rearrange the items so that the spray arms can rotate freely.
The filter combination in the base of the wash chamber is not clean or is not correctly fitted.
This may cause the spray arm jets to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets, if necessary (see
"Cleaning and care").
The non-return valve is open and blocked. Dirty water has flowed back into the wash chamber.
Clean the drain pump and the non-return valve
(see "Frequently asked questions").
The rinse aid dosage is set too high.
Reduce the dosage (see "Settings menu - Rinse aid").
The rinse aid dosage is set too low or the rinse aid reservoir is empty.
Replenish the rinse aid, increase the dosage or change the brand of rinse aid used (see "Adding rinse aid").
Dishware was taken out of the chamber too soon.
Leave it in for longer (see "Operation").
68
Frequently asked questions
Problem
White residue is visible on the dishware.
Clouding occurs on glassware and cutlery; the deposit can be wiped off.
Possible cause and solution
The rinse aid dosage is too low.
Increase the dosage (see "Settings menu,
Rinse aid ").
The salt reservoir is empty.
Fill the reactivation salt reservoir (see "Filling the salt reservoir").
The softener assembly is programmed too low for the water hardness level.
Program the softener assembly to the correct value (see "Settings, Water hardness").
Detergent deposits.
Switch to another detergent right away.
Glasses have a brownish-blue discoloration; the deposit cannot be wiped off.
Glasses are dull and discolored; the deposit cannot be wiped off.
Tea or lipstick stains have not been completely removed.
Plastic parts are discolored.
There are rust stains on the cutlery.
The glassware is not dishwasher-safe. The surfaces are affected.
Purchase glassware which is dishwasher-safe.
The wash temperature of the selected program was too low.
Select a program with a higher wash temperature.
The bleaching effect of the detergent is too low.
Switch to another detergent.
Natural dyes e.g. from carrots, tomatoes or ketchup may be the cause. The amount of detergent used or its bleaching effect was not sufficient to deal with natural dyes.
Use more detergent (see "Operation, Adding detergent").
Discolored plastic items will not regain their original color.
A program was not run after reactivation salt was added. Traces of salt entered the wash cycle.
Always run the " Rinse & Hold " program without a wash load after refilling salt.
The affected items are not corrosion resistant.
Purchase cutlery which is dishwasher-proof.
69
Frequently asked questions
Cleaning the water intake
A filter is incorporated in the screw connection of the water intake valve.
The filter must be cleaned when dirty; otherwise, insufficient water flows into the wash chamber.
The plastic housing of the water connection contains an electrical component.
The housing must not be dipped in water.
Recommendation
If your water supply contains a large number of insoluble substances, we recommend fitting a large-area filter in the connection between the water supply valve and the water inlet hose threaded union. This filter is available from Miele.
To clean the filter:
Disconnect the dishwasher from the electrical supply (switch the dishwasher off, unplug it or disconnect or disable the fuse/circuit breaker).
Close the water supply valve.
Unscrew the water intake valve.
Take the seal ring out of the screw connection.
Withdraw the filter using pointed pliers and rinse clean under running water.
Take care when withdrawing the filter not to pull out or dislodge the flow regulator located underneath the filter.
Replace the filter and washer, making sure they are sitting correctly.
Reconnect the water intake valve to the faucet, making sure it goes on correctly and is not cross-threaded.
Open the water faucet gradually to test for leaks.
If there is a leak, the inlet hose might not be secured properly, or it may have been screwed on at an angle.
Unscrew and reconnect the water inlet hose correctly before tightening it.
70
Frequently asked questions
Cleaning the drain pump and non-return valve
If the water has not been pumped away at the end of a program, the drain pump or the non-return valve might be blocked. They are, however, easy to clean.
Disconnect the dishwasher from the electrical supply (switch the dishwasher off, unplug it or disconnect or disable the fuse/circuit breaker).
Take the filter combination out of the wash chamber (see "Cleaning and care", "Cleaning the filters").
Scoop the water out of the wash chamber using a suitable container or utensil.
The drain pump is located under the non-return valve (see arrow).
Remove all foreign objects from the drain pump carefully (watch out for glass splinters which are particularly difficult to detect). Turn the drain pump impeller by hand to check that there are no more obstructions. You will feel a little resistance when you turn the impeller.
Carefully reinsert the non-return valve and secure it with the locking clamp.
Make sure the locking clamp clicks into place!
Be careful not to damage any delicate components when cleaning the drain pump and the non-return valve.
Press the catch for the non-return valve inwards .
Lift out the non-return valve and rinse it well under running water.
Remove all foreign objects from the non-return valve.
71
Miele Service
Repairs
In the event of any faults that you cannot remedy yourself, please contact:
– the Miele Service Department, or
– your Miele dealer or
– a qualified specialist.
When contacting Miele, you will need the model and serial number of your dishwasher.
These can be found on the data plate along the right edge of the open door.
PC Update
The Program Correction (PC) allows a technician to update the dishwasher to make use of new technology.
These updates can only be performed by a Miele Service Technician.
72
Electrical connection
Electrical connection
All work on the electrical connection must be carried out by
Miele, a Miele-authorized technician or a qualified electrician.
Converting the machine to a different type of power supply can lead to longer program durations, resulting in increased energy consumption.
The values declared on the label will only be achieved if the machine remains in the state in which it was delivered.
– The electrical installation must be in compliance with current local and national safety regulations!
– Connection to the power supply must be made via a suitable plug and socket which conforms to national regulations and must be accessible for service and maintenance work after the machine has been installed.
– If the dishwasher is hard-wired to the power supply, a main switch capable of disconnecting the dishwasher at all poles must be installed. This master switch must have a contact gap of at least 1/8" (3 mm) and also be lockable in the Off position.
– If necessary, equipotential bonding must be carried out.
– If replacing the power cable, use only original Miele replacement parts or a suitable cable with core cable ends.
– For technical data, see the data plate or the attached wiring diagram!
The dishwasher must only be operated with the voltage, frequency and fuse rating shown on the data plate.
This appliance can be converted to a different type of power supply in accordance with the conversion diagram and wiring diagram supplied.
The data plates are located at the back of the dishwasher and along the right edge of the open door.
The wiring diagram is supplied with the dishwasher.
The conversion diagram is attached to the base panel behind the plastic base cover.
Grounding connection
The ground lead must be connected to the screw connection point (marked with the ground symbol ) at the back of the machine.
WARNING
THIS APPLIANCE MUST BE
GROUNDED
Warning: This machine must be grounded!
The dishwasher can be connected using a switch or plug. The installation must be performed by a certified electrician under consideration of local regulations.
73
Plumbing
The Miele WaterProof System
Provided your dishwasher has been installed correctly, the Miele Waterproof system will provide protection against water damage throughout its lifetime.
Water intake
The water in the dishwasher is
NOT safe to drink!
– The dishwasher's connection to the water supply system must be in compliance with local codes.
– The water quality should satisfy local drinking water requirements.
A high iron content can lead to external rust deposits on the wash load and the dishwasher itself.
A chloride concentration greater than
100 mg/l in the process water significantly increases the risk of corrosion for the wash load.
– In certain regions (e.g. mountainous areas), the typical water composition can cause precipitates to form, which in turn requires the use of softened water for the dishwasher.
– A device for preventing the return flow of water is not necessary, as this dishwasher conforms to the applicable standards for the protection of drinking water.
– Water pressure: Must be between
4.35 - 145 psi (0.3 - 10 bar).
If the water pressure is lower than this, the fault message
Water intake will appear in the display (see
"Frequently asked questions").
If the water pressure is too high, a pressure reducer valve must be fitted.
– A shut-off valve with a
3
/
4
inch male thread must be provided on site. It should be easily accessible so that the water supply can be turned off when the dishwasher is not in use.
– The intake hose is an approx.
59" (1.5 m) long DN 10 pressure hose with a
3
/
4
" screw connection. A
59" (1.5 m) flexible metal hose (test pressure: 140 bar) is available as an extension. Do not remove the filter and flow regulator from the screw connection.
74
To avoid any damage to the appliance, the dishwasher must only be connected to fully vented pipework.
Plumbing
The intake hose must not be shortened or damaged in any way as it contains electrical components
(see illustration).
75
Plumbing
Connection to the drainage system
– The dishwasher drain contains a built-in non-return valve which prevents dirty water from flowing back into the dishwasher via the drain hose.
– The dishwasher drainage hose should be connected to a separate on-site drain for the dishwasher only.
If no separate drain is available, we recommend connecting it to a dualchamber siphon.
– The dishwasher is equipped with a
59" (1.5 m) long flexible drain hose
(clear width of 7/8" (22 mm)).
Clamps for connecting the hose are included with the dishwasher.
– Do not shorten the drain hose! The hose can be extended by a connecting piece and an additional hose. The length of the drainage line may not exceed 13' (4 m) and the delivery head must be no higher than
39" (1 m).
– The drainage system must be able to handle a discharge rate of at least
4.2 g/min (16 l/min).
Make sure that there are no kinks in the hose, and that it is not crushed or stretched.
Venting the drain
If the on-site drain connection is situated lower than the guide path for the bottom basket rollers in the open door, the drain must be vented.
Otherwise a siphoning effect during a program can cause the appliance to empty itself of water.
To vent it:
Open the dishwasher door fully.
Pull the lower spray arm firmly upwards to remove it.
Cut off the top of the vent valve in the wash chamber.
76
Technical details
Commercial Dishwasher model
Height
PG 8083 SCVi
Installation height
Width
Installation width
Depth
Weight
Voltage
Connected load
Fuse rating
Drain pump height
Drain hose length
Power cable
Capacity
Noise emission values
Sound power in LwA
Sound pressure in LpA
Manufacturer's address
33 1/4" (845 mm)
(adjustable + 2 9/16" (65 mm))
33 1/4" (845 mm)
(adjustable + 2 9/16" (65 mm))
23 9/16" (598 mm)
23 5/8" (600 mm)
22 7/16" (570 mm)
128 lb (57,5 kg)
See data plate
Power consumption when switched off
Power consumption when not switched off
Water pressure (supply pressure)
Cold or hot water supply
Water hardness
0.30 W
2.00 W
4.35 - 145 psi (30 - 1,000 kPa)
Up to max. 140°F (60°C) max. 37.5 gpg (36°d) max. 3' 3 3/8" (1 m) max. 13' 1 1/2" (4 m)
Approx. 5' 7" (1.7 m)
14 place settings
49 dB (A)
38 dB (A)
Miele & Cie. KG, Carl-Miele-Straße 29,
33332 Gütersloh, Germany
77
Sound emission tests
Setup for sound emission tests
Test standard IEC 60704-2-3
The dishwasher needs to be set up according to the following information:
Install the dishwasher into an analyzing unit.
Secure the front panel.
78
Sound emission tests
Push the provided fleece strips (depending on model) under the toe-kick until it is flush with the appliance feet
Push the toe-kick into place in such a way that it is flush with the door front .
79
aaa
Please have the model and serial number of your machine available when contacting Technical Service.
U.S.A.
Miele, Inc.
National Headquarters
9 Independence Way
Princeton, NJ 08540
Phone:
800-991-9380
Fax:
609-419-4241 www.miele-pro.com
Technical Service & Support
Phone: 800-991-9380
Fax: 800-220-1348 [email protected]
2017-01-16
M.-Nr. 09 501 402 / 00
Изтегляне
Публичната връзка е актуализирана
Публичната връзка към вашия чат е актуализирана. You may view and manage your chat links after registration here.
Публична връзка към документа
Реклама