ST STM32F100xx advanced ARM®-based 32-bit MCUs Reference Manual

RM0041
Reference manual
advanced
STM32F100xx
32-bit MCUs
ARM®-based
Introduction
This reference manual targets application developers. It provides complete information on
how to use the STM32F100x4, STM32F100x6, STM32F100x8, STM32F100xB,
STM32F100xC, STM32F100xD and STM32F100xE microcontroller memory and
peripherals. The STM32F100x4, STM32F100x6, STM32F100x8, STM32F100xB,
STM32F100xC, STM32F100xD and STM32F100xE will be referred to as STM32F100xx
throughout the document, unless otherwise specified.
The STM32F100xx is a family of microcontrollers with different memory sizes, packages
and peripherals.
For ordering information, mechanical and electrical device characteristics, refer to the
STM32F100xx datasheet.
For information on programming, erasing and protection of the internal Flash memory refer
to the STM32F100xx Flash programming manual (PM0063).
For information on the ARM® Cortex®-M3 core, refer to the Cortex®-M3 Technical
Reference Manual.
Related documents
Available from www.arm.com:
• Cortex®-M3 Technical Reference Manual
Available from www.st.com:
• STM32F100xx datasheets
• STM32F100xx Flash programming manual
June 2016
Doc ID16188 Rev 5
1/713
www.st.com
1
Contents
RM0041
Contents
1
2
Documentation conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.1
List of abbreviations for registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.2
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.3
Peripheral availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Memory and bus architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.1
System architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.2
Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.3
Memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.4
3
4
Embedded SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.3.2
Bit banding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.3.3
Embedded Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Boot configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
CRC calculation unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.1
CRC introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.2
CRC main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.3
CRC functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.4
CRC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.4.1
Data register (CRC_DR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.4.2
Independent data register (CRC_IDR) . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.4.3
Control register (CRC_CR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.4.4
CRC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Power control (PWR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.1
4.2
4.3
2/713
2.3.1
Power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.1.1
Independent A/D and D/A converter supply and reference voltage . . . . 50
4.1.2
Battery backup domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.1.3
Voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Power supply supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.2.1
Power on reset (POR)/power down reset (PDR) . . . . . . . . . . . . . . . . . . 51
4.2.2
Programmable voltage detector (PVD) . . . . . . . . . . . . . . . . . . . . . . . . . 52
Low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Doc ID16188 Rev 5
RM0041
Contents
4.4
5
Slowing down system clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.3.2
Peripheral clock gating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.3.3
Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.3.4
Stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.3.5
Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.3.6
Auto-wakeup (AWU) from low-power mode . . . . . . . . . . . . . . . . . . . . . . 59
Power control registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.4.1
Power control register (PWR_CR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.4.2
Power control/status register (PWR_CSR) . . . . . . . . . . . . . . . . . . . . . . 61
4.4.3
PWR register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Backup registers (BKP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.1
BKP introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.2
BKP main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.3
BKP functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
5.4
6
4.3.1
5.3.1
Tamper detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
5.3.2
RTC calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
BKP registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5.4.1
Backup data register x (BKP_DRx) (x = 1 ..42) . . . . . . . . . . . . . . . . . . . 65
5.4.2
RTC clock calibration register (BKP_RTCCR) . . . . . . . . . . . . . . . . . . . . 65
5.4.3
Backup control register (BKP_CR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4.4
Backup control/status register (BKP_CSR) . . . . . . . . . . . . . . . . . . . . . . 66
5.4.5
BKP register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Reset and clock control (RCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6.1
6.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6.1.1
System reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6.1.2
Power reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
6.1.3
Backup domain reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
6.2.1
HSE clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
6.2.2
HSI clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
6.2.3
PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
6.2.4
LSE clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
6.2.5
LSI clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
6.2.6
System clock (SYSCLK) selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Doc ID16188 Rev 5
3/713
21
Contents
RM0041
6.3
7
Clock security system (CSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
6.2.8
RTC clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
6.2.9
Watchdog clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.2.10
Clock-out capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
RCC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.3.1
Clock control register (RCC_CR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.3.2
Clock configuration register (RCC_CFGR) . . . . . . . . . . . . . . . . . . . . . . 80
6.3.3
Clock interrupt register (RCC_CIR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.3.4
APB2 peripheral reset register (RCC_APB2RSTR) . . . . . . . . . . . . . . . 84
6.3.5
APB1 peripheral reset register (RCC_APB1RSTR) . . . . . . . . . . . . . . . 86
6.3.6
AHB peripheral clock enable register (RCC_AHBENR) . . . . . . . . . . . . 88
6.3.7
APB2 peripheral clock enable register (RCC_APB2ENR) . . . . . . . . . . . 90
6.3.8
APB1 peripheral clock enable register (RCC_APB1ENR) . . . . . . . . . . . 92
6.3.9
Backup domain control register (RCC_BDCR) . . . . . . . . . . . . . . . . . . . 95
6.3.10
Control/status register (RCC_CSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
6.3.11
Clock configuration register2 (RCC_CFGR2) . . . . . . . . . . . . . . . . . . . . 98
6.3.12
RCC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
General-purpose and alternate-function I/Os
(GPIOs and AFIOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
7.1
7.2
4/713
6.2.7
GPIO functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
7.1.1
General-purpose I/O (GPIO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
7.1.2
Atomic bit set or reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
7.1.3
External interrupt/wakeup lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.1.4
Alternate functions (AF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.1.5
Software remapping of I/O alternate functions . . . . . . . . . . . . . . . . . . 103
7.1.6
GPIO locking mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.1.7
Input configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
7.1.8
Output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
7.1.9
Alternate function configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
7.1.10
Analog configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
7.1.11
GPIO configurations for device peripherals . . . . . . . . . . . . . . . . . . . . . 107
GPIO registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
7.2.1
Port configuration register low (GPIOx_CRL) (x=A..G) . . . . . . . . . . . . 111
7.2.2
Port configuration register high (GPIOx_CRH) (x=A..G) . . . . . . . . . . . 112
7.2.3
Port input data register (GPIOx_IDR) (x=A..G) . . . . . . . . . . . . . . . . . . 112
7.2.4
Port output data register (GPIOx_ODR) (x=A..G) . . . . . . . . . . . . . . . . 113
Doc ID16188 Rev 5
RM0041
Contents
7.3
7.4
7.5
8
7.2.5
Port bit set/reset register (GPIOx_BSRR) (x=A..G) . . . . . . . . . . . . . . . 113
7.2.6
Port bit reset register (GPIOx_BRR) (x=A..G) . . . . . . . . . . . . . . . . . . . 114
7.2.7
Port configuration lock register (GPIOx_LCKR) (x=A..G) . . . . . . . . . . 114
Alternate function I/O and debug configuration (AFIO) . . . . . . . . . . . . . 115
7.3.1
Using OSC32_IN/OSC32_OUT pins as GPIO ports PC14/PC15 . . . . 115
7.3.2
Using OSC_IN/OSC_OUT pins as GPIO ports PD0/PD1 . . . . . . . . . . 115
7.3.3
JTAG/SWD alternate function remapping . . . . . . . . . . . . . . . . . . . . . . 116
7.3.4
Timer alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
7.3.5
USART alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . 119
7.3.6
I2C1 alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
7.3.7
SPI1 alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
7.3.8
CEC remap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
AFIO registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
7.4.1
Event control register (AFIO_EVCR) . . . . . . . . . . . . . . . . . . . . . . . . . . 121
7.4.2
AF remap and debug I/O configuration register (AFIO_MAPR) . . . . . . 122
7.4.3
External interrupt configuration register 1 (AFIO_EXTICR1) . . . . . . . . 124
7.4.4
External interrupt configuration register 2 (AFIO_EXTICR2) . . . . . . . . 124
7.4.5
External interrupt configuration register 3 (AFIO_EXTICR3) . . . . . . . . 125
7.4.6
External interrupt configuration register 4 (AFIO_EXTICR4) . . . . . . . . 125
7.4.7
AF remap and debug I/O configuration register (AFIO_MAPR2) . . . . . 126
GPIO and AFIO register maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Interrupts and events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
8.1
8.2
8.3
Nested vectored interrupt controller (NVIC) . . . . . . . . . . . . . . . . . . . . . . 130
8.1.1
SysTick calibration value register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
8.1.2
Interrupt and exception vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
External interrupt/event controller (EXTI) . . . . . . . . . . . . . . . . . . . . . . . . 134
8.2.1
Main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
8.2.2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
8.2.3
Wakeup event management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
8.2.4
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
8.2.5
External interrupt/event line mapping . . . . . . . . . . . . . . . . . . . . . . . . . 136
EXTI registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
8.3.1
Interrupt mask register (EXTI_IMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
8.3.2
Event mask register (EXTI_EMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
8.3.3
Rising trigger selection register (EXTI_RTSR) . . . . . . . . . . . . . . . . . . 139
Doc ID16188 Rev 5
5/713
21
Contents
9
RM0041
6/713
Falling trigger selection register (EXTI_FTSR) . . . . . . . . . . . . . . . . . . 139
8.3.5
Software interrupt event register (EXTI_SWIER) . . . . . . . . . . . . . . . . . 140
8.3.6
Pending register (EXTI_PR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
8.3.7
EXTI register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Direct memory access controller (DMA) . . . . . . . . . . . . . . . . . . . . . . . 142
9.1
DMA introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
9.2
DMA main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
9.3
DMA functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
9.4
10
8.3.4
9.3.1
DMA transactions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
9.3.2
Arbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
9.3.3
DMA channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
9.3.4
Programmable data width, data alignment and endians . . . . . . . . . . . 147
9.3.5
Error management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
9.3.6
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
9.3.7
DMA request mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
DMA registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
9.4.1
DMA interrupt status register (DMA_ISR) . . . . . . . . . . . . . . . . . . . . . . 152
9.4.2
DMA interrupt flag clear register (DMA_IFCR) . . . . . . . . . . . . . . . . . . 153
9.4.3
DMA channel x configuration register (DMA_CCRx) (x = 1..7,
where x = channel number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
9.4.4
DMA channel x number of data register (DMA_CNDTRx) (x = 1..7,
where x = channel number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
9.4.5
DMA channel x peripheral address register (DMA_CPARx) (x = 1..7,
where x = channel number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
9.4.6
DMA channel x memory address register (DMA_CMARx) (x = 1..7,
where x = channel number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
9.4.7
DMA register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Analog-to-digital converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
10.1
ADC introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
10.2
ADC main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
10.3
ADC functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
10.3.1
ADC on-off control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
10.3.2
ADC clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
10.3.3
Channel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
10.3.4
Single conversion mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
10.3.5
Continuous conversion mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Doc ID16188 Rev 5
RM0041
Contents
10.3.6
Timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
10.3.7
Analog watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
10.3.8
Scan mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
10.3.9
Injected channel management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
10.3.10 Discontinuous mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
10.4
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
10.5
Data alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
10.6
Channel-by-channel programmable sample time . . . . . . . . . . . . . . . . . . 169
10.7
Conversion on external trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
10.8
DMA request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
10.9
Temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
10.10 ADC interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
10.11 ADC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
10.11.1 ADC status register (ADC_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
10.11.2 ADC control register 1 (ADC_CR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
10.11.3 ADC control register 2 (ADC_CR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
10.11.4 ADC sample time register 1 (ADC_SMPR1) . . . . . . . . . . . . . . . . . . . . 178
10.11.5 ADC sample time register 2 (ADC_SMPR2) . . . . . . . . . . . . . . . . . . . . 179
10.11.6 ADC injected channel data offset register x (ADC_JOFRx) (x=1..4) . . 179
10.11.7 ADC watchdog high threshold register (ADC_HTR) . . . . . . . . . . . . . . 180
10.11.8 ADC watchdog low threshold register (ADC_LTR) . . . . . . . . . . . . . . . 180
10.11.9 ADC regular sequence register 1 (ADC_SQR1) . . . . . . . . . . . . . . . . . 181
10.11.10 ADC regular sequence register 2 (ADC_SQR2) . . . . . . . . . . . . . . . . . 182
10.11.11 ADC regular sequence register 3 (ADC_SQR3) . . . . . . . . . . . . . . . . . 183
10.11.12 ADC injected sequence register (ADC_JSQR) . . . . . . . . . . . . . . . . . . 184
10.11.13 ADC injected data register x (ADC_JDRx) (x= 1..4) . . . . . . . . . . . . . . 185
10.11.14 ADC regular data register (ADC_DR) . . . . . . . . . . . . . . . . . . . . . . . . . 185
10.11.15 ADC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
11
Digital-to-analog converter (DAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
11.1
DAC introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
11.2
DAC main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
11.3
DAC functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
11.3.1
DAC channel enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
11.3.2
DAC output buffer enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
11.3.3
DAC data format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Doc ID16188 Rev 5
7/713
21
Contents
RM0041
11.4
11.3.4
DAC conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
11.3.5
DAC output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
11.3.6
DAC trigger selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
11.3.7
DMA request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
11.3.8
Noise generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
11.3.9
Triangle-wave generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Dual DAC channel conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
11.4.1
Independent trigger without wave generation . . . . . . . . . . . . . . . . . . . 195
11.4.2
Independent trigger with single LFSR generation . . . . . . . . . . . . . . . . 196
11.4.3
Independent trigger with different LFSR generation . . . . . . . . . . . . . . 196
11.4.4
Independent trigger with single triangle generation . . . . . . . . . . . . . . . 197
11.4.5
Independent trigger with different triangle generation . . . . . . . . . . . . . 197
11.4.6
Simultaneous software start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
11.4.7
Simultaneous trigger without wave generation . . . . . . . . . . . . . . . . . . 198
11.4.8
Simultaneous trigger with single LFSR generation . . . . . . . . . . . . . . . 198
11.4.9
Simultaneous trigger with different LFSR generation . . . . . . . . . . . . . 198
11.4.10 Simultaneous trigger with single triangle generation . . . . . . . . . . . . . . 199
11.4.11 Simultaneous trigger with different triangle generation . . . . . . . . . . . . 199
11.5
DAC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
11.5.1
DAC control register (DAC_CR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
11.5.2
DAC software trigger register (DAC_SWTRIGR) . . . . . . . . . . . . . . . . . 203
11.5.3
DAC channel1 12-bit right-aligned data holding register
(DAC_DHR12R1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
11.5.4
DAC channel1 12-bit left aligned data holding register
(DAC_DHR12L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
11.5.5
DAC channel1 8-bit right aligned data holding register
(DAC_DHR8R1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
11.5.6
DAC channel2 12-bit right aligned data holding register
(DAC_DHR12R2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
11.5.7
DAC channel2 12-bit left aligned data holding register
(DAC_DHR12L2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
11.5.8
DAC channel2 8-bit right-aligned data holding register
(DAC_DHR8R2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
11.5.9
Dual DAC 12-bit right-aligned data holding register
(DAC_DHR12RD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
11.5.10 DUAL DAC 12-bit left aligned data holding register
(DAC_DHR12LD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
11.5.11 DUAL DAC 8-bit right aligned data holding register
(DAC_DHR8RD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
8/713
Doc ID16188 Rev 5
RM0041
Contents
11.5.12 DAC channel1 data output register (DAC_DOR1) . . . . . . . . . . . . . . . . 207
11.5.13 DAC channel2 data output register (DAC_DOR2) . . . . . . . . . . . . . . . . 207
11.5.14 DAC status register (DAC_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
11.5.15 DAC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
12
Advanced-control timer (TIM1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
12.1
TIM1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
12.2
TIM1 main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
12.3
TIM1 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
12.3.1
Time-base unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
12.3.2
Counter modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
12.3.3
Repetition counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
12.3.4
Clock selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
12.3.5
Capture/compare channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
12.3.6
Input capture mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
12.3.7
PWM input mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
12.3.8
Forced output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
12.3.9
Output compare mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
12.3.10 PWM mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
12.3.11 Complementary outputs and dead-time insertion . . . . . . . . . . . . . . . . 238
12.3.12 Using the break function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
12.3.13 Clearing the OCxREF signal on an external event . . . . . . . . . . . . . . . 243
12.3.14 6-step PWM generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
12.3.15 One-pulse mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
12.3.16 Encoder interface mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
12.3.17 Timer input XOR function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
12.3.18 Interfacing with Hall sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
12.3.19 TIMx and external trigger synchronization . . . . . . . . . . . . . . . . . . . . . . 251
12.3.20 Timer synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
12.3.21 Debug mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
12.4
TIM1 registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
12.4.1
TIM1 control register 1 (TIMx_CR1) . . . . . . . . . . . . . . . . . . . . . . . . . . 255
12.4.2
TIM1 control register 2 (TIMx_CR2) . . . . . . . . . . . . . . . . . . . . . . . . . . 256
12.4.3
TIM1 slave mode control register (TIMx_SMCR) . . . . . . . . . . . . . . . . . 259
12.4.4
TIM1 DMA/interrupt enable register (TIMx_DIER) . . . . . . . . . . . . . . . . 261
12.4.5
TIM1 status register (TIMx_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
12.4.6
TIM1 event generation register (TIMx_EGR) . . . . . . . . . . . . . . . . . . . . 264
Doc ID16188 Rev 5
9/713
21
Contents
RM0041
12.4.7
TIM1 capture/compare mode register 1 (TIMx_CCMR1) . . . . . . . . . . 266
12.4.8
TIM1 capture/compare mode register 2 (TIMx_CCMR2) . . . . . . . . . . 268
12.4.9
TIM1 capture/compare enable register (TIMx_CCER) . . . . . . . . . . . . 270
12.4.10 TIM1 counter (TIMx_CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
12.4.11 TIM1 prescaler (TIMx_PSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
12.4.12 TIM1 auto-reload register (TIMx_ARR) . . . . . . . . . . . . . . . . . . . . . . . . 273
12.4.13 TIM1 repetition counter register (TIMx_RCR) . . . . . . . . . . . . . . . . . . . 274
12.4.14 TIM1 capture/compare register 1 (TIMx_CCR1) . . . . . . . . . . . . . . . . . 274
12.4.15 TIM1 capture/compare register 2 (TIMx_CCR2) . . . . . . . . . . . . . . . . . 275
12.4.16 TIM1 capture/compare register 3 (TIMx_CCR3) . . . . . . . . . . . . . . . . . 275
12.4.17 TIM1 capture/compare register 4 (TIMx_CCR4) . . . . . . . . . . . . . . . . . 276
12.4.18 TIM1 break and dead-time register (TIMx_BDTR) . . . . . . . . . . . . . . . 276
12.4.19 TIM1 DMA control register (TIMx_DCR) . . . . . . . . . . . . . . . . . . . . . . . 278
12.4.20 TIM1 DMA address for full transfer (TIMx_DMAR) . . . . . . . . . . . . . . . 279
12.4.21 TIM1 register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
13
General-purpose timers (TIM2 to TIM5) . . . . . . . . . . . . . . . . . . . . . . . . 282
13.1
TIM2 to TIM5 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
13.2
TIM2 to TIM5 main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
13.3
TIM2 to TIM5 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
13.3.1
Time-base unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
13.3.2
Counter modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
13.3.3
Clock selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
13.3.4
Capture/compare channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
13.3.5
Input capture mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
13.3.6
PWM input mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
13.3.7
Forced output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
13.3.8
Output compare mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
13.3.9
PWM mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
13.3.10 One-pulse mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
13.3.11 Clearing the OCxREF signal on an external event . . . . . . . . . . . . . . . 307
13.3.12 Encoder interface mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
13.3.13 Timer input XOR function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
13.3.14 Timers and external trigger synchronization . . . . . . . . . . . . . . . . . . . . 311
13.3.15 Timer synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
13.3.16 Debug mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
13.4
10/713
TIMx2 to TIM5 registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Doc ID16188 Rev 5
RM0041
Contents
13.4.1
TIMx control register 1 (TIMx_CR1) . . . . . . . . . . . . . . . . . . . . . . . . . . 319
13.4.2
TIMx control register 2 (TIMx_CR2) . . . . . . . . . . . . . . . . . . . . . . . . . . 321
13.4.3
TIMx slave mode control register (TIMx_SMCR) . . . . . . . . . . . . . . . . . 322
13.4.4
TIMx DMA/Interrupt enable register (TIMx_DIER) . . . . . . . . . . . . . . . . 324
13.4.5
TIMx status register (TIMx_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
13.4.6
TIMx event generation register (TIMx_EGR) . . . . . . . . . . . . . . . . . . . . 327
13.4.7
TIMx capture/compare mode register 1 (TIMx_CCMR1) . . . . . . . . . . . 328
13.4.8
TIMx capture/compare mode register 2 (TIMx_CCMR2) . . . . . . . . . . . 331
13.4.9
TIMx capture/compare enable register (TIMx_CCER) . . . . . . . . . . . . . 332
13.4.10 TIMx counter (TIMx_CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
13.4.11 TIMx prescaler (TIMx_PSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
13.4.12 TIMx auto-reload register (TIMx_ARR) . . . . . . . . . . . . . . . . . . . . . . . . 334
13.4.13 TIMx capture/compare register 1 (TIMx_CCR1) . . . . . . . . . . . . . . . . . 334
13.4.14 TIMx capture/compare register 2 (TIMx_CCR2) . . . . . . . . . . . . . . . . . 334
13.4.15 TIMx capture/compare register 3 (TIMx_CCR3) . . . . . . . . . . . . . . . . . 335
13.4.16 TIMx capture/compare register 4 (TIMx_CCR4) . . . . . . . . . . . . . . . . . 335
13.4.17 TIMx DMA control register (TIMx_DCR) . . . . . . . . . . . . . . . . . . . . . . . 336
13.4.18 TIMx DMA address for full transfer (TIMx_DMAR) . . . . . . . . . . . . . . . 336
13.4.19 TIMx register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
14
General-purpose timers (TIM12/13/14) . . . . . . . . . . . . . . . . . . . . . . . . 340
14.1
TIM12/13/14 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
14.2
TIM12/13/14 main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
14.3
14.2.1
TIM12 main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
14.2.2
TIM13/TIM14 main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
TIM12/13/14 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
14.3.1
Time-base unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
14.3.2
Counter modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
14.3.3
Clock selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348
14.3.4
Capture/compare channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
14.3.5
Input capture mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
14.3.6
PWM input mode (only for TIM12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
14.3.7
Forced output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
14.3.8
Output compare mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
14.3.9
PWM mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
14.3.10 One-pulse mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
14.3.11 TIM12 external trigger synchronization . . . . . . . . . . . . . . . . . . . . . . . . 358
Doc ID16188 Rev 5
11/713
21
Contents
RM0041
14.3.12 Timer synchronization (TIM12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
14.3.13 Debug mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
14.4
TIM12 registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
14.4.1
TIM12 control register 1 (TIMx_CR1) . . . . . . . . . . . . . . . . . . . . . . . . . 362
14.4.2
TIM12 control register 2 (TIMx_CR2) . . . . . . . . . . . . . . . . . . . . . . . . . 364
14.4.3
TIM12 slave mode control register (TIMx_SMCR) . . . . . . . . . . . . . . . . 365
14.4.4
TIM12 Interrupt enable register (TIMx_DIER) . . . . . . . . . . . . . . . . . . . 366
14.4.5
TIM12 status register (TIMx_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
14.4.6
TIM event generation register (TIMx_EGR) . . . . . . . . . . . . . . . . . . . . . 369
14.4.7
TIM capture/compare mode register 1 (TIMx_CCMR1) . . . . . . . . . . . 371
14.4.8
TIM12 capture/compare enable register (TIMx_CCER) . . . . . . . . . . . 374
14.4.9
TIM12 counter (TIMx_CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
14.4.10 TIM12 prescaler (TIMx_PSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
14.4.11 TIM12 auto-reload register (TIMx_ARR) . . . . . . . . . . . . . . . . . . . . . . . 375
14.4.12 TIM12 capture/compare register 1 (TIMx_CCR1) . . . . . . . . . . . . . . . . 376
14.4.13 TIM12 capture/compare register 2 (TIMx_CCR2) . . . . . . . . . . . . . . . . 376
14.4.14 TIM12 register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
14.5
TIM13/14 registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
14.5.1
TIM13/14 control register 1 (TIMx_CR1) . . . . . . . . . . . . . . . . . . . . . . . 379
14.5.2
TIM10/11/13/14 Interrupt enable register (TIMx_DIER) . . . . . . . . . . . 380
14.5.3
TIM13/14 status register (TIMx_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . 380
14.5.4
TIM13/14 event generation register (TIMx_EGR) . . . . . . . . . . . . . . . . 381
14.5.5
TIM13/14 capture/compare mode register 1 (TIMx_CCMR1) . . . . . . . 382
14.5.6
TIM13/14 capture/compare enable register (TIMx_CCER) . . . . . . . . . 385
14.5.7
TIM13/14 counter (TIMx_CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
14.5.8
TIM13/14 prescaler (TIMx_PSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
14.5.9
TIM13/14 auto-reload register (TIMx_ARR) . . . . . . . . . . . . . . . . . . . . 386
14.5.10 TIM13/14 capture/compare register 1 (TIMx_CCR1) . . . . . . . . . . . . . 387
14.5.11 TIM13/14 register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
15
General-purpose timers (TIM15/16/17) . . . . . . . . . . . . . . . . . . . . . . . . 389
15.1
TIM15/16/17 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
15.2
TIM15 main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
15.3
TIM16 and TIM17 main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
15.4
TIM15/16/17 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
15.4.1
12/713
Time-base unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Doc ID16188 Rev 5
RM0041
Contents
15.4.2
Counter modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
15.4.3
Repetition counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
15.4.4
Clock selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
15.4.5
Capture/compare channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
15.4.6
Input capture mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
15.4.7
PWM input mode (only for TIM15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
15.4.8
Forced output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
15.4.9
Output compare mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
15.4.10 PWM mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
15.4.11 Complementary outputs and dead-time insertion . . . . . . . . . . . . . . . . 408
15.4.12 Using the break function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
15.4.13 One-pulse mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
15.4.14 TIM15 and external trigger synchronization (only for TIM15) . . . . . . . 414
15.4.15 Timer synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
15.4.16 Debug mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
15.5
TIM15 registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
15.5.1
TIM15 control register 1 (TIM15_CR1) . . . . . . . . . . . . . . . . . . . . . . . . 417
15.5.2
TIM15 control register 2 (TIM15_CR2) . . . . . . . . . . . . . . . . . . . . . . . . 418
15.5.3
TIM15 slave mode control register (TIM15_SMCR) . . . . . . . . . . . . . . 419
15.5.4
TIM15 DMA/interrupt enable register (TIM15_DIER) . . . . . . . . . . . . . 421
15.5.5
TIM15 status register (TIM15_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
15.5.6
TIM15 event generation register (TIM15_EGR) . . . . . . . . . . . . . . . . . . 423
15.5.7
TIM15 capture/compare mode register 1 (TIM15_CCMR1) . . . . . . . . 424
15.5.8
TIM15 capture/compare enable register (TIM15_CCER) . . . . . . . . . . 427
15.5.9
TIM15 counter (TIM15_CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
15.5.10 TIM15 prescaler (TIM15_PSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
15.5.11 TIM15 auto-reload register (TIM15_ARR) . . . . . . . . . . . . . . . . . . . . . . 430
15.5.12 TIM15 repetition counter register (TIM15_RCR) . . . . . . . . . . . . . . . . . 431
15.5.13 TIM15 capture/compare register 1 (TIM15_CCR1) . . . . . . . . . . . . . . . 431
15.5.14 TIM15 capture/compare register 2 (TIM15_CCR2) . . . . . . . . . . . . . . . 432
15.5.15 TIM15 break and dead-time register (TIM15_BDTR) . . . . . . . . . . . . . 432
15.5.16 TIM15 DMA control register (TIM15_DCR) . . . . . . . . . . . . . . . . . . . . . 434
15.5.17 TIM15 DMA address for full transfer (TIM15_DMAR) . . . . . . . . . . . . . 435
15.5.18 TIM15 register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435
15.6
TIM16&TIM17 registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438
15.6.1
TIM16&TIM17 control register 1 (TIMx_CR1) . . . . . . . . . . . . . . . . . . . 438
15.6.2
TIM16&TIM17 control register 2 (TIMx_CR2) . . . . . . . . . . . . . . . . . . . 439
Doc ID16188 Rev 5
13/713
21
Contents
RM0041
15.6.3
TIM16&TIM17 DMA/interrupt enable register (TIMx_DIER) . . . . . . . . 441
15.6.4
TIM16&TIM17 status register (TIMx_SR) . . . . . . . . . . . . . . . . . . . . . . 442
15.6.5
TIM16&TIM17 event generation register (TIMx_EGR) . . . . . . . . . . . . 443
15.6.6
TIM16&TIM17 capture/compare mode register 1 (TIMx_CCMR1) . . . 444
15.6.7
TIM16&TIM17 capture/compare enable register (TIMx_CCER) . . . . . 447
15.6.8
TIM16&TIM17 counter (TIMx_CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . 450
15.6.9
TIM16&TIM17 prescaler (TIMx_PSC) . . . . . . . . . . . . . . . . . . . . . . . . . 450
15.6.10 TIM16&TIM17 auto-reload register (TIMx_ARR) . . . . . . . . . . . . . . . . . 450
15.6.11 TIM16&TIM17 repetition counter register (TIMx_RCR) . . . . . . . . . . . . 451
15.6.12 TIM16&TIM17 capture/compare register 1 (TIMx_CCR1) . . . . . . . . . . 451
15.6.13 TIM16&TIM17 break and dead-time register (TIMx_BDTR) . . . . . . . . 452
15.6.14 TIM16&TIM17 DMA control register (TIMx_DCR) . . . . . . . . . . . . . . . . 453
15.6.15 TIM16&TIM17 DMA address for full transfer (TIMx_DMAR) . . . . . . . . 454
15.6.16 TIM16&TIM17 register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
16
Basic timers (TIM6 and TIM7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
16.1
TIM6&TIM7 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
16.2
TIM6&TIM7 main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
16.3
TIM6&TIM7 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
16.4
17
14/713
16.3.1
Time-base unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
16.3.2
Counting mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
16.3.3
Clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
16.3.4
Debug mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
TIM6&TIM7 registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
16.4.1
TIM6&TIM7 control register 1 (TIMx_CR1) . . . . . . . . . . . . . . . . . . . . . 465
16.4.2
TIM6&TIM7 control register 2 (TIMx_CR2) . . . . . . . . . . . . . . . . . . . . . 467
16.4.3
TIM6&TIM7 DMA/Interrupt enable register (TIMx_DIER) . . . . . . . . . . 467
16.4.4
TIM6&TIM7 status register (TIMx_SR) . . . . . . . . . . . . . . . . . . . . . . . . 468
16.4.5
TIM6&TIM7 event generation register (TIMx_EGR) . . . . . . . . . . . . . . 468
16.4.6
TIM6&TIM7 counter (TIMx_CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
16.4.7
TIM6&TIM7 prescaler (TIMx_PSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
16.4.8
TIM6&TIM7 auto-reload register (TIMx_ARR) . . . . . . . . . . . . . . . . . . . 469
16.4.9
TIM6&TIM7 register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470
Real-time clock (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
17.1
RTC introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
17.2
RTC main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
Doc ID16188 Rev 5
RM0041
Contents
17.3
17.4
18
17.3.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
17.3.2
Resetting RTC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
17.3.3
Reading RTC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
17.3.4
Configuring RTC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
17.3.5
RTC flag assertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
RTC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 476
17.4.1
RTC control register high (RTC_CRH) . . . . . . . . . . . . . . . . . . . . . . . . 476
17.4.2
RTC control register low (RTC_CRL) . . . . . . . . . . . . . . . . . . . . . . . . . . 477
17.4.3
RTC prescaler load register (RTC_PRLH / RTC_PRLL) . . . . . . . . . . . 478
17.4.4
RTC prescaler divider register (RTC_DIVH / RTC_DIVL) . . . . . . . . . . 479
17.4.5
RTC counter register (RTC_CNTH / RTC_CNTL) . . . . . . . . . . . . . . . . 480
17.4.6
RTC alarm register high (RTC_ALRH / RTC_ALRL) . . . . . . . . . . . . . . 481
17.4.7
RTC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482
Independent watchdog (IWDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483
18.1
IWDG introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483
18.2
IWDG main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483
18.3
IWDG functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483
18.4
19
RTC functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
18.3.1
Hardware watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
18.3.2
Register access protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
18.3.3
Debug mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
IWDG registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
18.4.1
Key register (IWDG_KR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
18.4.2
Prescaler register (IWDG_PR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
18.4.3
Reload register (IWDG_RLR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
18.4.4
Status register (IWDG_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
18.4.5
IWDG register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 488
Window watchdog (WWDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489
19.1
WWDG introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489
19.2
WWDG main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489
19.3
WWDG functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489
19.4
How to program the watchdog timeout . . . . . . . . . . . . . . . . . . . . . . . . . . 491
19.5
Debug mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492
19.6
WWDG registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493
Doc ID16188 Rev 5
15/713
21
Contents
20
RM0041
19.6.1
Control register (WWDG_CR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493
19.6.2
Configuration register (WWDG_CFR) . . . . . . . . . . . . . . . . . . . . . . . . . 494
19.6.3
Status register (WWDG_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494
19.6.4
WWDG register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
Flexible static memory controller (FSMC) . . . . . . . . . . . . . . . . . . . . . 496
20.1
FSMC main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496
20.2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
20.3
AHB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
20.3.1
20.4
External device address mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
20.4.1
20.5
21
Supported memories and transactions . . . . . . . . . . . . . . . . . . . . . . . . 498
NOR/PSRAM address mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
NOR Flash/PSRAM controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
20.5.1
External memory interface signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
20.5.2
Supported memories and transactions . . . . . . . . . . . . . . . . . . . . . . . . 503
20.5.3
General timing rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504
20.5.4
NOR Flash/PSRAM controller asynchronous transactions . . . . . . . . . 505
20.5.5
Synchronous transactions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523
20.5.6
NOR/PSRAM control registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 529
20.5.7
FSMC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537
Serial peripheral interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539
21.1
SPI introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539
21.2
SPI main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
21.2.1
21.3
SPI features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
SPI functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
21.3.1
General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
21.3.2
Configuring the SPI in slave mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
21.3.3
Configuring the SPI in master mode . . . . . . . . . . . . . . . . . . . . . . . . . . 546
21.3.4
Configuring the SPI for half-duplex communication . . . . . . . . . . . . . . . 547
21.3.5
Data transmission and reception procedures . . . . . . . . . . . . . . . . . . . 547
21.3.6
CRC calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554
21.3.7
Status flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556
21.3.8
Disabling the SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557
21.3.9
SPI communication using DMA (direct memory addressing) . . . . . . . 558
21.3.10 Error flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560
16/713
Doc ID16188 Rev 5
RM0041
Contents
21.3.11 SPI interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
21.4
22
SPI registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562
21.4.1
SPI control register 1 (SPI_CR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562
21.4.2
SPI control register 2 (SPI_CR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563
21.4.3
SPI status register (SPI_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564
21.4.4
SPI data register (SPI_DR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
21.4.5
SPI CRC polynomial register (SPI_CRCPR) . . . . . . . . . . . . . . . . . . . . 566
21.4.6
SPI RX CRC register (SPI_RXCRCR) . . . . . . . . . . . . . . . . . . . . . . . . . 566
21.4.7
SPI TX CRC register (SPI_TXCRCR) . . . . . . . . . . . . . . . . . . . . . . . . . 566
21.4.8
SPI register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
Inter-integrated circuit (I2C) interface . . . . . . . . . . . . . . . . . . . . . . . . . 569
22.1
I2C introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569
22.2
I2C main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569
22.3
I2C functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 570
22.3.1
Mode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 570
22.3.2
I2C slave mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572
22.3.3
I2C master mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575
22.3.4
Error conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583
22.3.5
SDA/SCL line control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584
22.3.6
SMBus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585
22.3.7
DMA requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587
22.3.8
Packet error checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589
22.4
I2C interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589
22.5
I2C debug mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 591
22.6
I2C registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 591
22.6.1
I2C Control register 1 (I2C_CR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 591
22.6.2
I2C Control register 2 (I2C_CR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593
22.6.3
I2C Own address register 1 (I2C_OAR1) . . . . . . . . . . . . . . . . . . . . . . . 595
22.6.4
I2C Own address register 2 (I2C_OAR2) . . . . . . . . . . . . . . . . . . . . . . . 595
22.6.5
I2C Data register (I2C_DR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596
22.6.6
I2C Status register 1 (I2C_SR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596
22.6.7
I2C Status register 2 (I2C_SR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
22.6.8
I2C Clock control register (I2C_CCR) . . . . . . . . . . . . . . . . . . . . . . . . . 601
22.6.9
I2C TRISE register (I2C_TRISE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602
22.6.10 I2C register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603
Doc ID16188 Rev 5
17/713
21
Contents
23
RM0041
Universal synchronous asynchronous receiver
transmitter (USART) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604
23.1
USART introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604
23.2
USART main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604
23.3
USART functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605
23.3.1
USART character description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 608
23.3.2
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609
23.3.3
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 612
23.3.4
Fractional baud rate generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617
23.3.5
USART receiver tolerance to clock deviation . . . . . . . . . . . . . . . . . . . . 622
23.3.6
Multiprocessor communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 622
23.3.7
Parity control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 624
23.3.8
LIN (local interconnection network) mode . . . . . . . . . . . . . . . . . . . . . . 625
23.3.9
USART synchronous mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 628
23.3.10 Single-wire half-duplex communication . . . . . . . . . . . . . . . . . . . . . . . . 630
23.3.11 Smartcard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631
23.3.12 IrDA SIR ENDEC block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633
23.3.13 Continuous communication using DMA . . . . . . . . . . . . . . . . . . . . . . . . 635
23.3.14 Hardware flow control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637
24
18/713
23.4
USART interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639
23.5
USART mode configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640
23.6
USART registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640
23.6.1
Status register (USART_SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640
23.6.2
Data register (USART_DR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643
23.6.3
Baud rate register (USART_BRR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643
23.6.4
Control register 1 (USART_CR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643
23.6.5
Control register 2 (USART_CR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 646
23.6.6
Control register 3 (USART_CR3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647
23.6.7
Guard time and prescaler register (USART_GTPR) . . . . . . . . . . . . . . 649
23.6.8
USART register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650
High-definition multimedia interface-consumer
electronics control controller (HDMI™-CEC) . . . . . . . . . . . . . . . . . . . 651
24.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 651
24.2
HDMI-CEC main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652
24.3
HDMI-CEC bus topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652
Doc ID16188 Rev 5
RM0041
Contents
24.4
24.5
25
24.3.1
HDMI-CEC pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652
24.3.2
Message description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653
24.3.3
Bit timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654
Arbitration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
24.4.1
Signal free time (SFT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
24.4.2
Header arbitration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
Error handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656
24.5.1
BTE, BPE and Error bit generation . . . . . . . . . . . . . . . . . . . . . . . . . . . 656
24.5.2
Message error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656
24.6
Device addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656
24.7
HDMI-CEC functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657
24.7.1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657
24.7.2
Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657
24.7.3
Rx digital filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 658
24.7.4
Rx bit timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 658
24.7.5
Tx bit timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659
24.7.6
CEC arbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 660
24.7.7
CEC states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661
24.7.8
CEC and system Stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665
24.8
HDMI-CEC interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666
24.9
HDMI-CEC registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667
24.9.1
CEC configuration register (CEC_CFGR) . . . . . . . . . . . . . . . . . . . . . . 667
24.9.2
CEC own address register (CEC_OAR) . . . . . . . . . . . . . . . . . . . . . . . 668
24.9.3
CEC prescaler register (CEC_PRES) . . . . . . . . . . . . . . . . . . . . . . . . . 668
24.9.4
CEC error status register (CEC_ESR) . . . . . . . . . . . . . . . . . . . . . . . . . 669
24.9.5
CEC control and status register (CEC_CSR) . . . . . . . . . . . . . . . . . . . 670
24.9.6
CEC Tx data register (CEC_TXD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 671
24.9.7
CEC Rx data register (CEC_RXD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 671
24.9.8
HDMI-CEC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 672
Debug support (DBG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673
25.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673
25.2
Reference ARM® documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675
25.3
SWJ debug port (serial wire and JTAG) . . . . . . . . . . . . . . . . . . . . . . . . . 675
25.3.1
25.4
Mechanism to select the JTAG-DP or the SW-DP . . . . . . . . . . . . . . . . 675
Pinout and debug port pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676
Doc ID16188 Rev 5
19/713
21
Contents
RM0041
25.4.1
SWJ debug port pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676
25.4.2
Flexible SWJ-DP pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676
25.4.3
Internal pull-up and pull-down on JTAG pins . . . . . . . . . . . . . . . . . . . . 677
25.4.4
Using serial wire and releasing the unused debug pins as GPIOs . . . 679
25.5
STM32F100xx JTAG TAP connection . . . . . . . . . . . . . . . . . . . . . . . . . . 679
25.6
ID codes and locking mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 681
25.6.1
MCU device ID code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 681
25.6.2
Boundary scan TAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
25.6.3
Cortex®-M3 TAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
25.6.4
Cortex®-M3 JEDEC-106 ID code . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
25.7
JTAG debug port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
25.8
SW debug port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
25.9
25.8.1
SW protocol introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
25.8.2
SW protocol sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
25.8.3
SW-DP state machine (reset, idle states, ID code) . . . . . . . . . . . . . . . 685
25.8.4
DP and AP read/write accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686
25.8.5
SW-DP registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686
25.8.6
SW-AP registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 687
AHB-AP (AHB access port) - valid for both JTAG-DP
and SW-DP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 687
25.10 Core debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 689
25.11 Capability of the debugger host to connect under system reset . . . . . . 690
25.12 FPB (Flash patch breakpoint) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690
25.13 DWT (data watchpoint trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
25.14 ITM (instrumentation trace macrocell) . . . . . . . . . . . . . . . . . . . . . . . . . . 691
25.14.1 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
25.14.2 Time stamp packets, synchronization and overflow packets . . . . . . . . 691
25.15 MCU debug component (DBGMCU) . . . . . . . . . . . . . . . . . . . . . . . . . . . 693
25.15.1 Debug support for low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . 693
25.15.2 Debug support for timers, watchdog and I2C . . . . . . . . . . . . . . . . . . . . 693
25.15.3 Debug MCU configuration register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
25.16 TPIU (trace port interface unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696
25.16.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696
25.16.2 TRACE pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698
25.16.3 TPUI formatter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 699
25.16.4 TPUI frame synchronization packets . . . . . . . . . . . . . . . . . . . . . . . . . . 700
20/713
Doc ID16188 Rev 5
RM0041
Contents
25.16.5 Transmission of the synchronization frame packet . . . . . . . . . . . . . . . 700
25.16.6 Synchronous mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700
25.16.7 Asynchronous mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701
25.16.8 TRACECLKIN connection inside the STM32F100xx . . . . . . . . . . . . . . 701
25.16.9 TPIU registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701
25.16.10 Example of configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702
25.17 DBG register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702
26
Device electronic signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 704
26.1
Memory size registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 704
26.1.1
26.2
27
Flash size register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 704
Unique device ID register (96 bits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709
Doc ID16188 Rev 5
21/713
21
List of tables
RM0041
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Table 28.
Table 29.
Table 30.
Table 31.
Table 32.
Table 33.
Table 34.
Table 35.
Table 36.
Table 37.
Table 38.
Table 39.
Table 40.
Table 41.
Table 42.
Table 43.
Table 44.
Table 45.
Table 46.
Table 47.
Table 48.
22/713
Low and medium-density device register boundary addresses . . . . . . . . . . . . . . . . . . . . . 36
High-density device register boundary addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Flash module organization (low-density value line devices) . . . . . . . . . . . . . . . . . . . . . . . . 41
Flash module organization (medium-density value line devices) . . . . . . . . . . . . . . . . . . . . 42
Flash module organization (high-density value line devices) . . . . . . . . . . . . . . . . . . . . . . . 42
Boot modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
CRC calculation unit register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Low-power mode summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Sleep-now . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Sleep-on-exit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
PWR register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
BKP register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
RCC register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Port bit configuration table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Output MODE bits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Advanced timer TIM1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
General-purpose timers TIM2/3/4/5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
General-purpose timers TIM15/16/17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
General-purpose timers TIM12/13/14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
USARTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
CEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
FSMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Other IOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Debug interface signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Debug port mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
TIM5 alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
TIM12 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
TIM13 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
TIM14 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
TIM4 alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
TIM3 alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
TIM2 alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
TIM1 alternate function remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
TIM1 DMA remapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
TIM15 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
TIM16 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
TIM17 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
USART3 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
USART2 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
USART1 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
I2C1 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
SPI1 remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
CEC remapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
GPIO register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Doc ID16188 Rev 5
RM0041
Table 49.
Table 50.
Table 51.
Table 52.
Table 53.
Table 54.
Table 55.
Table 56.
Table 57.
Table 58.
Table 59.
Table 60.
Table 61.
Table 62.
Table 63.
Table 64.
Table 65.
Table 66.
Table 67.
Table 68.
Table 69.
Table 70.
Table 71.
Table 72.
Table 73.
Table 74.
Table 75.
Table 76.
Table 77.
Table 78.
Table 79.
Table 80.
Table 81.
Table 82.
Table 83.
Table 84.
Table 85.
Table 86.
Table 87.
Table 88.
Table 89.
Table 90.
Table 91.
Table 92.
Table 93.
Table 94.
Table 95.
Table 96.
Table 97.
Table 98.
List of tables
AFIO register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Vector table for STM32F100xx devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
External interrupt/event controller register map and reset values. . . . . . . . . . . . . . . . . . . 141
Programmable data width & endian behavior (when bits PINC = MINC = 1) . . . . . . . . . . 147
DMA interrupt requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Summary of DMA1 requests for each channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Summary of DMA2 requests for each channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
DMA register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
ADC pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Analog watchdog channel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
External trigger for regular channels for ADC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
External trigger for injected channels for ADC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
ADC interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
ADC register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
DAC pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
External triggers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
DAC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Counting direction versus encoder signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
TIMx Internal trigger connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
Output control bits for complementary OCx and OCxN channels with
break feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
TIM1 register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Counting direction versus encoder signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
TIMx internal trigger connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
Output control bit for standard OCx channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
TIMx register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
TIMx Internal trigger connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
Output control bit for standard OCx channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
TIM12 register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
Output control bit for standard OCx channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
TIM13/14 register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
TIMx Internal trigger connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
Output control bits for complementary OCx and OCxN channels with break feature . . . . 429
TIM15 register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
Output control bits for complementary OCx and OCxN channels with break feature . . . . 449
TIM16&TIM17 register map and reset values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
TIM6&TIM7 register map and reset values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470
RTC register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482
Min/max IWDG timeout period at 40 kHz (LSI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
IWDG register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 488
Minimum and maximum timeout values @24 MHz (fPCLK1) . . . . . . . . . . . . . . . . . . . . . . . 492
WWDG register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
NOR/PSRAM bank selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
External memory address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
Programmable NOR/PSRAM access parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
Nonmultiplexed I/O NOR Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
Multiplexed I/O NOR Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
Nonmultiplexed I/Os PSRAM/SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502
Multiplexed I/O PSRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502
NOR Flash/PSRAM controller: example of supported memories
and transactions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503
FSMC_BCRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506
Doc ID16188 Rev 5
23/713
25
List of tables
Table 99.
Table 100.
Table 101.
Table 102.
Table 103.
Table 104.
Table 105.
Table 106.
Table 107.
Table 108.
Table 109.
Table 110.
Table 111.
Table 112.
Table 113.
Table 114.
Table 115.
Table 116.
Table 117.
Table 118.
Table 119.
Table 120.
Table 121.
Table 122.
Table 123.
Table 124.
Table 125.
Table 126.
Table 127.
Table 128.
Table 129.
Table 130.
Table 131.
Table 132.
Table 133.
Table 134.
Table 135.
Table 136.
Table 137.
Table 138.
Table 139.
Table 140.
Table 141.
Table 142.
Table 143.
Table 144.
Table 145.
Table 146.
24/713
RM0041
FSMC_BTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
FSMC_BCRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
FSMC_BTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
FSMC_BWTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510
FSMC_BCRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
FSMC_BTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
FSMC_BWTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
FSMC_BCRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
FSMC_BTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
FSMC_BWTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
FSMC_BCRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
FSMC_BTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
FSMC_BWTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
FSMC_BCRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
FSMC_BTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
FSMC_BCRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525
FSMC_BTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526
FSMC_BCRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527
FSMC_BTRx bit fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528
FSMC register map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537
SPI interrupt requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
SPI register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
SMBus vs. I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585
I2C Interrupt requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589
I2C register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603
Noise detection from sampled data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616
Error calculation for programmed baud rates at fPCLK = 8 MHz or fPCLK = 12 MHz,
oversampling by 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 619
Error calculation for programmed baud rates at fPCLK = 8 MHz or fPCLK =12 MHz,
oversampling by 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 620
Error calculation for programmed baud rates at fPCLK = 16 MHz or fPCLK = 24 MHz,
oversampling by 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 620
Error calculation for programmed baud rates at fPCLK = 16 MHz or fPCLK = 24 MHz,
oversampling by 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621
USART receiver’s tolerance when DIV fraction is 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 622
USART receiver tolerance when DIV_Fraction is different from 0 . . . . . . . . . . . . . . . . . . 622
Frame formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 624
USART interrupt requests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639
USART mode configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640
USART register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650
HDMI pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653
Signal free time definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
Bit status depending on the low bit duration (LBD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659
Bit status depending on the total bit duration (TBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659
STM32 CEC arbitration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 660
Software sequence to respect when receiving a message. . . . . . . . . . . . . . . . . . . . . . . . 662
Software sequence to respect when transmitting a message . . . . . . . . . . . . . . . . . . . . . 663
Software sequence to respect when transmitting a message . . . . . . . . . . . . . . . . . . . . . 665
HDMI-CEC interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666
HDMI-CEC register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 672
SWJ debug port pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676
Flexible SWJ-DP pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 677
Doc ID16188 Rev 5
RM0041
Table 147.
Table 148.
Table 149.
Table 150.
Table 151.
Table 152.
Table 153.
Table 154.
Table 155.
Table 156.
Table 157.
Table 158.
Table 159.
Table 160.
Table 161.
List of tables
JTAG debug port data registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
32-bit debug port registers addressed through the shifted value A[3:2] . . . . . . . . . . . . . . 683
Packet request (8-bits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
ACK response (3 bits). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685
DATA transfer (33 bits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685
SW-DP registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686
Cortex®-M3 AHB-AP registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 688
Core debug registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 689
Main ITM registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 692
Asynchronous TRACE pin assignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698
Synchronous TRACE pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698
Flexible TRACE pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 699
Important TPIU registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701
Value DBG register map and reset values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709
Doc ID16188 Rev 5
25/713
25
List of figures
RM0041
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Figure 42.
Figure 43.
Figure 44.
Figure 45.
Figure 46.
26/713
Low and medium density value line system architecture . . . . . . . . . . . . . . . . . . . . . . . . . . 33
High density value line system architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CRC calculation unit block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Power supply overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Power on reset/power down reset waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
PVD thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Simplified diagram of the reset circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
STM32F100xx clock tree (low and medium-density devices). . . . . . . . . . . . . . . . . . . . . . . 71
STM32F100xx clock tree (high-density devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
HSE/ LSE clock sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Basic structure of a standard I/O port bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Basic structure of a five-volt tolerant I/O port bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Input floating/pull up/pull down configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Alternate function configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
High impedance-analog configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
ADC / DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
External interrupt/event controller block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
External interrupt/event GPIO mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
DMA block diagram in low and medium- density
Cat.1 and Cat.2 STM32F100xx devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
DMA block diagram in high-density
Cat.4 and Cat.5 STM32F100xx devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
DMA1 request mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
DMA2 request mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Single ADC block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Analog watchdog guarded area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Injected conversion latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Calibration timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Right alignment of data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Left alignment of data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Temperature sensor and VREFINT channel block diagram . . . . . . . . . . . . . . . . . . . . . . 171
DAC channel block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Data registers in single DAC channel mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Data registers in dual DAC channel mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Timing diagram for conversion with trigger disabled TEN = 0 . . . . . . . . . . . . . . . . . . . . . 192
DAC LFSR register calculation algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
DAC conversion (SW trigger enabled) with LFSR wave generation. . . . . . . . . . . . . . . . . 194
DAC triangle wave generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
DAC conversion (SW trigger enabled) with triangle wave generation . . . . . . . . . . . . . . . 195
Advanced-control timer block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Counter timing diagram with prescaler division change from 1 to 2 . . . . . . . . . . . . . . . . . 214
Counter timing diagram with prescaler division change from 1 to 4 . . . . . . . . . . . . . . . . . 214
Counter timing diagram, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Counter timing diagram, internal clock divided by 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Doc ID16188 Rev 5
RM0041
Figure 47.
Figure 48.
Figure 49.
Figure 50.
Figure 51.
Figure 52.
Figure 53.
Figure 54.
Figure 55.
Figure 56.
Figure 57.
Figure 58.
Figure 59.
Figure 60.
Figure 61.
Figure 62.
Figure 63.
Figure 64.
Figure 65.
Figure 66.
Figure 67.
Figure 68.
Figure 69.
Figure 70.
Figure 71.
Figure 72.
Figure 73.
Figure 74.
Figure 75.
Figure 76.
Figure 77.
Figure 78.
Figure 79.
Figure 80.
Figure 81.
Figure 82.
Figure 83.
Figure 84.
Figure 85.
Figure 86.
Figure 87.
Figure 88.
Figure 89.
Figure 90.
Figure 91.
Figure 92.
Figure 93.
Figure 94.
Figure 95.
Figure 96.
Figure 97.
Figure 98.
List of figures
Counter timing diagram, update event when ARPE=0 (TIMx_ARR not preloaded) . . . . . 217
Counter timing diagram, update event when ARPE=1 (TIMx_ARR preloaded) . . . . . . . . 217
Counter timing diagram, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
Counter timing diagram, internal clock divided by 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Counter timing diagram, update event when repetition counter is not used . . . . . . . . . . . 221
Counter timing diagram, internal clock divided by 1, TIMx_ARR = 0x6 . . . . . . . . . . . . . . 222
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Counter timing diagram, internal clock divided by 4, TIMx_ARR=0x36 . . . . . . . . . . . . . . 223
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Counter timing diagram, update event with ARPE=1 (counter underflow) . . . . . . . . . . . . 224
Counter timing diagram, Update event with ARPE=1 (counter overflow) . . . . . . . . . . . . . 224
Update rate examples depending on mode and TIMx_RCR register settings . . . . . . . . . 225
Control circuit in normal mode, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . 226
TI2 external clock connection example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Control circuit in external clock mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
External trigger input block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Control circuit in external clock mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
Capture/compare channel (example: channel 1 input stage) . . . . . . . . . . . . . . . . . . . . . . 230
Capture/compare channel 1 main circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Output stage of capture/compare channel (channel 1 to 3) . . . . . . . . . . . . . . . . . . . . . . . 231
Output stage of capture/compare channel (channel 4). . . . . . . . . . . . . . . . . . . . . . . . . . . 231
PWM input mode timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
Output compare mode, toggle on OC1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Edge-aligned PWM waveforms (ARR=8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Center-aligned PWM waveforms (ARR=8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Complementary output with dead-time insertion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Dead-time waveforms with delay greater than the negative pulse. . . . . . . . . . . . . . . . . . 239
Dead-time waveforms with delay greater than the positive pulse. . . . . . . . . . . . . . . . . . . 239
Output behavior in response to a break.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Clearing TIMx OCxREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
6-step generation, COM example (OSSR=1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Example of one pulse mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Example of counter operation in encoder interface mode. . . . . . . . . . . . . . . . . . . . . . . . . 248
Example of encoder interface mode with TI1FP1 polarity inverted. . . . . . . . . . . . . . . . . . 248
Example of hall sensor interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Control circuit in reset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Control circuit in gated mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Control circuit in trigger mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
Control circuit in external clock mode 2 + trigger mode . . . . . . . . . . . . . . . . . . . . . . . . . . 254
General-purpose timer block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
Counter timing diagram with prescaler division change from 1 to 2 . . . . . . . . . . . . . . . . . 285
Counter timing diagram with prescaler division change from 1 to 4 . . . . . . . . . . . . . . . . . 286
Counter timing diagram, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Counter timing diagram, internal clock divided by 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Counter timing diagram, Update event when ARPE=0 (TIMx_ARR not preloaded). . . . . 288
Counter timing diagram, Update event when ARPE=1 (TIMx_ARR preloaded). . . . . . . . 289
Counter timing diagram, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
Doc ID16188 Rev 5
27/713
31
List of figures
Figure 99.
Figure 100.
Figure 101.
Figure 102.
Figure 103.
Figure 104.
Figure 105.
Figure 106.
Figure 107.
Figure 108.
Figure 109.
Figure 110.
Figure 111.
Figure 112.
Figure 113.
Figure 114.
Figure 115.
Figure 116.
Figure 117.
Figure 118.
Figure 119.
Figure 120.
Figure 121.
Figure 122.
Figure 123.
Figure 124.
Figure 125.
Figure 126.
Figure 127.
Figure 128.
Figure 129.
Figure 130.
Figure 131.
Figure 132.
Figure 133.
Figure 134.
Figure 135.
Figure 136.
Figure 137.
Figure 138.
Figure 139.
Figure 140.
Figure 141.
Figure 142.
Figure 143.
Figure 144.
Figure 145.
Figure 146.
Figure 147.
Figure 148.
Figure 149.
Figure 150.
28/713
RM0041
Counter timing diagram, internal clock divided by 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
Counter timing diagram, Update event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
Counter timing diagram, internal clock divided by 1, TIMx_ARR=0x6 . . . . . . . . . . . . . . . 292
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Counter timing diagram, internal clock divided by 4, TIMx_ARR=0x36 . . . . . . . . . . . . . . 293
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Counter timing diagram, Update event with ARPE=1 (counter underflow). . . . . . . . . . . . 294
Counter timing diagram, Update event with ARPE=1 (counter overflow) . . . . . . . . . . . . . 294
Control circuit in normal mode, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . 295
TI2 external clock connection example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
Control circuit in external clock mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
External trigger input block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
Control circuit in external clock mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
Capture/compare channel (example: channel 1 input stage) . . . . . . . . . . . . . . . . . . . . . . 298
Capture/compare channel 1 main circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Output stage of capture/compare channel (channel 1). . . . . . . . . . . . . . . . . . . . . . . . . . . 299
PWM input mode timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
Output compare mode, toggle on OC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Edge-aligned PWM waveforms (ARR=8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
Center-aligned PWM waveforms (ARR=8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
Example of one-pulse mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
Clearing TIMx OCxREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
Example of counter operation in encoder interface mode . . . . . . . . . . . . . . . . . . . . . . . . 310
Example of encoder interface mode with TI1FP1 polarity inverted . . . . . . . . . . . . . . . . . 310
Control circuit in reset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Control circuit in gated mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
Control circuit in trigger mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
Control circuit in external clock mode 2 + trigger mode . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Master/Slave timer example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Gating TIM2 with OC1REF of TIM3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
Gating TIM2 with Enable of TIM3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
Triggering TIM2 with update of TIM3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Triggering TIM2 with Enable of TIM3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Triggering TIM3 and TIM2 with TIM3 TI1 input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
General-purpose timer block diagram (TIM12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
General-purpose timer block diagram (TIM13/14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
Counter timing diagram with prescaler division change from 1 to 2 . . . . . . . . . . . . . . . . . 344
Counter timing diagram with prescaler division change from 1 to 4 . . . . . . . . . . . . . . . . . 344
Counter timing diagram, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
Counter timing diagram, internal clock divided by 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
Counter timing diagram, update event when ARPE=0 (TIMx_ARR not preloaded) . . . . . 347
Counter timing diagram, update event when ARPE=1 (TIMx_ARR preloaded) . . . . . . . . 347
Control circuit in normal mode, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . 348
TI2 external clock connection example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
Control circuit in external clock mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
Capture/compare channel (example: channel 1 input stage) . . . . . . . . . . . . . . . . . . . . . . 350
Capture/compare channel 1 main circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
Output stage of capture/compare channel (channel 1). . . . . . . . . . . . . . . . . . . . . . . . . . . 351
PWM input mode timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
Doc ID16188 Rev 5
RM0041
Figure 151.
Figure 152.
Figure 153.
Figure 154.
Figure 155.
Figure 156.
Figure 157.
Figure 158.
Figure 159.
Figure 160.
Figure 161.
Figure 162.
Figure 163.
Figure 164.
Figure 165.
Figure 166.
Figure 167.
Figure 168.
Figure 169.
Figure 170.
Figure 171.
Figure 172.
Figure 173.
Figure 174.
Figure 175.
Figure 176.
Figure 177.
Figure 178.
Figure 179.
Figure 180.
Figure 181.
Figure 182.
Figure 183.
Figure 184.
Figure 185.
Figure 186.
Figure 187.
Figure 188.
Figure 189.
Figure 190.
Figure 191.
Figure 192.
Figure 193.
Figure 194.
Figure 195.
Figure 196.
Figure 197.
Figure 198.
List of figures
Output compare mode, toggle on OC1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
Edge-aligned PWM waveforms (ARR=8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
Example of one pulse mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
Control circuit in reset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
Control circuit in gated mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
Control circuit in trigger mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
TIM15 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
TIM16 and TIM17 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
Counter timing diagram with prescaler division change from 1 to 2 . . . . . . . . . . . . . . . . . 395
Counter timing diagram with prescaler division change from 1 to 4 . . . . . . . . . . . . . . . . . 395
Counter timing diagram, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
Counter timing diagram, internal clock divided by 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Counter timing diagram, update event when ARPE=0 (TIMx_ARR not
preloaded). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Counter timing diagram, update event when ARPE=1 (TIMx_ARR
preloaded). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
Update rate examples depending on mode and TIMx_RCR register settings . . . . . . . . . 399
Control circuit in normal mode, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . 400
TI2 external clock connection example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
Control circuit in external clock mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
Capture/compare channel (example: channel 1 input stage) . . . . . . . . . . . . . . . . . . . . . . 401
Capture/compare channel 1 main circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402
Output stage of capture/compare channel (channel 1). . . . . . . . . . . . . . . . . . . . . . . . . . . 402
Output stage of capture/compare channel (channel 2 for TIM15) . . . . . . . . . . . . . . . . . . 402
PWM input mode timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
Output compare mode, toggle on OC1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
Edge-aligned PWM waveforms (ARR=8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
Complementary output with dead-time insertion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408
Dead-time waveforms with delay greater than the negative pulse. . . . . . . . . . . . . . . . . . 408
Dead-time waveforms with delay greater than the positive pulse. . . . . . . . . . . . . . . . . . . 409
Output behavior in response to a break.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
Example of one pulse mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
Control circuit in reset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
Control circuit in gated mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
Control circuit in trigger mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
Basic timer block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
Counter timing diagram with prescaler division change from 1 to 2 . . . . . . . . . . . . . . . . . 460
Counter timing diagram with prescaler division change from 1 to 4 . . . . . . . . . . . . . . . . . 461
Counter timing diagram, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462
Counter timing diagram, internal clock divided by 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462
Counter timing diagram, internal clock divided by 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
Counter timing diagram, internal clock divided by N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
Counter timing diagram, update event when ARPE=0 (TIMx_ARR not
preloaded). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
Counter timing diagram, update event when ARPE=1 (TIMx_ARR
preloaded). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
Control circuit in normal mode, internal clock divided by 1 . . . . . . . . . . . . . . . . . . . . . . . . 464
RTC simplified block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
RTC second and alarm waveform example with PR=0003, ALARM=00004 . . . . . . . . . . 475
RTC Overflow waveform example with PR=0003. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
Doc ID16188 Rev 5
29/713
31
List of figures
Figure 199.
Figure 200.
Figure 201.
Figure 202.
Figure 203.
Figure 204.
Figure 205.
Figure 206.
Figure 207.
Figure 208.
Figure 209.
Figure 210.
Figure 211.
Figure 212.
Figure 213.
Figure 214.
Figure 215.
Figure 216.
Figure 217.
Figure 218.
Figure 219.
Figure 220.
Figure 221.
Figure 222.
Figure 223.
Figure 224.
Figure 225.
Figure 226.
Figure 227.
Figure 228.
Figure 229.
Figure 230.
Figure 231.
Figure 232.
Figure 233.
Figure 234.
Figure 235.
Figure 236.
Figure 237.
Figure 238.
Figure 239.
Figure 240.
Figure 241.
Figure 242.
Figure 243.
Figure 244.
30/713
RM0041
Independent watchdog block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
Watchdog block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490
Window watchdog timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
FSMC block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
FSMC memory banks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
Mode1 read accesses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
Mode1 write accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506
ModeA read accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
ModeA write accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
Mode2 and mode B read accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510
Mode2 write accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
Mode B write accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
Mode C read accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
Mode C write accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
Mode D read accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
Mode D write accesses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
Multiplexed read accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
Multiplexed write accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
Asynchronous wait during a read access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521
Asynchronous wait during a write access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522
Wait configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524
Synchronous multiplexed read mode - NOR, PSRAM (CRAM) . . . . . . . . . . . . . . . . . . . . 525
Synchronous multiplexed write mode - PSRAM (CRAM) . . . . . . . . . . . . . . . . . . . . . . . . . 527
SPI block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
Single master/ single slave application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542
Data clock timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
TXE/RXNE/BSY behavior in Master / full-duplex mode (BIDIMODE=0 and
RXONLY=0) in case of continuous transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
TXE/RXNE/BSY behavior in Slave / full-duplex mode (BIDIMODE=0,
RXONLY=0) in case of continuous transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
TXE/BSY behavior in Master transmit-only mode (BIDIMODE=0 and RXONLY=0)
in case of continuous transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
TXE/BSY in Slave transmit-only mode (BIDIMODE=0 and RXONLY=0) in case of
continuous transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552
RXNE behavior in receive-only mode (BIDIRMODE=0 and RXONLY=1)
in case of continuous transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553
TXE/BSY behavior when transmitting (BIDIRMODE=0 and RXONLY=0)
in case of discontinuous transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554
Transmission using DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559
Reception using DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559
I2C bus protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 571
I2C block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572
Transfer sequence diagram for slave transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574
Transfer sequence diagram for slave receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575
Transfer sequence diagram for master transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578
Method 1: transfer sequence diagram for master receiver . . . . . . . . . . . . . . . . . . . . . . . 580
Method 2: transfer sequence diagram for master receiver when N>2 . . . . . . . . . . . . . . . 581
Method 2: transfer sequence diagram for master receiver when N=2 . . . . . . . . . . . . . . . 582
Method 2: transfer sequence diagram for master receiver when N=1 . . . . . . . . . . . . . . . 583
I2C interrupt mapping diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 590
USART block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607
Word length programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 608
Doc ID16188 Rev 5
RM0041
Figure 245.
Figure 246.
Figure 247.
Figure 248.
Figure 249.
Figure 250.
Figure 251.
Figure 252.
Figure 253.
Figure 254.
Figure 255.
Figure 256.
Figure 257.
Figure 258.
Figure 259.
Figure 260.
Figure 261.
Figure 262.
Figure 263.
Figure 264.
Figure 265.
Figure 266.
Figure 267.
Figure 268.
Figure 269.
Figure 270.
Figure 271.
Figure 272.
Figure 273.
Figure 274.
Figure 275.
Figure 276.
Figure 277.
Figure 278.
Figure 279.
Figure 280.
Figure 281.
Figure 282.
Figure 283.
Figure 284.
Figure 285.
Figure 286.
Figure 287.
List of figures
Configurable stop bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610
TC/TXE behavior when transmitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611
Start bit detection when oversampling by 16 or 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 612
Data sampling when oversampling by 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615
Data sampling when oversampling by 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616
Mute mode using Idle line detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623
Mute mode using address mark detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 624
Break detection in LIN mode (11-bit break length - LBDL bit is set) . . . . . . . . . . . . . . . . . 627
Break detection in LIN mode vs. Framing error detection. . . . . . . . . . . . . . . . . . . . . . . . . 628
USART example of synchronous transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 629
USART data clock timing diagram (M=0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 629
USART data clock timing diagram (M=1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630
RX data setup/hold time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630
ISO 7816-3 asynchronous protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631
Parity error detection using the 1.5 stop bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632
IrDA SIR ENDEC- block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 634
IrDA data modulation (3/16) -Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 634
Transmission using DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 636
Reception using DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637
Hardware flow control between 2 USARTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637
RTS flow control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638
CTS flow control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638
USART interrupt mapping diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639
CEC line connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653
Message structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654
Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654
Bit timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654
Follower acknowledge (ACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
Signal free time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
Arbitration phase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
Error bit timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656
HDMI-CEC block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657
Bit timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 658
Tx bit timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659
CEC control state machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661
Example of a complete message reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 662
Example of a complete message transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663
Example of a message transmission with transmission error . . . . . . . . . . . . . . . . . . . . . . 664
CEC and system Stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666
Block diagram of STM32 MCU and Cortex®-M3-level debug support . . . . . . . . . . . . . . 674
SWJ debug port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675
JTAG TAP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680
TPIU block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697
Doc ID16188 Rev 5
31/713
31
Documentation conventions
RM0041
1
Documentation conventions
1.1
List of abbreviations for registers
The following abbreviations are used in register descriptions:
read/write (rw)
Software can read and write to these bits.
read-only (r)
Software can only read these bits.
write-only (w)
Software can only write to this bit. Reading the bit returns the reset
value.
read/clear (rc_w1) Software can read as well as clear this bit by writing 1. Writing ‘0’ has
no effect on the bit value.
read/clear (rc_w0) Software can read as well as clear this bit by writing 0. Writing ‘1’ has
no effect on the bit value.
read/clear by read Software can read this bit. Reading this bit automatically clears it to ‘0’.
(rc_r)
Writing ‘0’ has no effect on the bit value.
1.2
read/set (rs)
Software can read as well as set this bit. Writing ‘0’ has no effect on the
bit value.
read-only write
trigger (rt_w)
Software can read this bit. Writing ‘0’ or ‘1’ triggers an event but has no
effect on the bit value.
toggle (t)
Software can only toggle this bit by writing ‘1’. Writing ‘0’ has no effect.
Reserved (Res.)
Reserved bit, must be kept at reset value.
Glossary
•
•
•
•
•
•
1.3
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the
Flash memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
Word: data of 32-bit length.
Half-word: data of 16-bit length.
Byte: data of 8-bit length.
Peripheral availability
For the availability and number of peripherals across all STM32F100xx sales types, refer to
the low, medium and high-density STM32F100xx datasheet.
32/713
Doc ID16188 Rev 5
RM0041
Memory and bus architecture
2
Memory and bus architecture
2.1
System architecture
In low-and medium-density value line devices, the main system consists of:
•
•
Three masters:
–
Cortex®-M3 core DCode bus (D-bus) and System bus (S-bus)
–
GP-DMA1 (general-purpose DMA)
Three slaves:
–
Internal SRAM
–
Internal Flash memory
–
AHB to APB bridges (AHB to APBx), which connect all the APB peripherals
These are interconnected using a multilayer AHB bus architecture as shown in Figure 1.
Figure 1. Low and medium density value line system architecture
)#ODE
$#ODE
&,!3(
&LASH
INTERFACE
&LASH
MEMORY
#ORTEX-
3YS TEM
$-!
32!-
"USMATRIX
$-!
#H
#H
!("SYSTEMBUS
#H
2ESETCLOCK
CONTROL2##
$-!REQUEST
"RIDGE "RIDGE 4)-
4)-
4)-
!0"
!0"
'0)/
53!24
30)
4)-
!$#
30)
$!#
4)-
$!#
4)-
)#
4)-
)#
53!24 4)-
53!244)-
#%#
$-!REQUEST
AI
Doc ID16188 Rev 5
33/713
45
Memory and bus architecture
RM0041
In high-density value line devices, the main system consists of:
•
•
Four masters:
–
Cortex®-M3 core DCode bus (D-bus) and System bus (S-bus)
–
GP-DMA1 & 2 (general-purpose DMA)
Four slaves:
–
Internal SRAM
–
Internal Flash memory
–
FSMC
–
AHB to APB bridges (AHB to APBx), which connect all the APB peripherals
These are interconnected using a multilayer AHB bus architecture as shown in Figure 2.
Figure 2. High density value line system architecture
)#ODE
$#ODE
&,!3(
&LASH
INFERFACE
&LASH
MEMORY
#ORTEX-
$-!
$-!
"USMATRIX
3YS TEM
32!&3-#
#H
!("SYSTEMBUS
#H
2ESETCLOCK
CONTROL2##
$-!
#H
$-!2EQUEST
$-!
"RIDGE "RIDGE !$#
53!24
30)
4)-
4)-
4)-
4)-
!0" !0"
'0)/ $!#
30)
$!#
30)
4)-
)#
4)-
)#
4)-
5!24
4)-
5!24
53!24 4)-
4)-
53!24
#%#
4)-
4)-
4)-
#H
#H
#H
$-!REQUEST
AI
ICode bus
This bus connects the instruction bus of the Cortex®-M3 core to the Flash memory
instruction interface. Instruction fetches are performed on this bus.
DCode bus
This bus connects the DCode bus (literal load and debug access) of the Cortex®-M3 core to
the Flash memory data interface.
34/713
Doc ID16188 Rev 5
RM0041
Memory and bus architecture
System bus
This bus connects the system bus of the Cortex®-M3 core (peripherals bus) to a bus matrix
which manages the arbitration between the core and the DMA.
DMA bus
This bus connects the AHB master interface of the DMA to the bus matrix which manages
the access of CPU DCode and DMA to the SRAM, Flash memory and peripherals.
Bus matrix
The bus matrix manages the access arbitration between the core system bus and the DMA
master bus. The arbitration uses a round robin algorithm. In low and medium-density value
line devices the bus matrix is composed of three masters (CPU DCode, System bus, DMA1
bus) and three slaves (FLITF, SRAM and AHB to APB bridges).
In high-density value line devices the bus matrix is composed of four masters (CPU DCode,
System bus, DMA1 bus and DMA2 bus) and four slaves (FLITF, SRAM, FSMC and AHB to
APB bridges).
AHB peripherals are connected to the system bus through the bus matrix to allow DMA
access.
AHB/APB bridges (APB)
The two AHB/APB bridges provide full synchronous connections between the AHB and the
two APB buses. APB buses operate at full speed (up to 24 MHz).
Refer to Table 2 for the address mapping of the peripherals connected to each bridge.
After each device reset, all peripheral clocks are disabled (except for the SRAM and FLITF).
Before using a peripheral its clock in the RCC_AHBENR, RCC_APB2ENR or
RCC_APB1ENR register must be enabled.
Note:
When a 16- or 8-bit access is performed on an APB register, the access is transformed into
a 32-bit access: the bridge duplicates the 16- or 8-bit data to feed the 32-bit vector.
2.2
Memory organization
Program memory, data memory, registers and I/O ports are organized within the same linear
4-Gbyte address space.
The bytes are coded in memory in little endian format. The lowest numbered byte in a word
is considered the word’s least significant byte and the highest numbered byte, the most
significant.
For the detailed mapping of peripheral registers, refer to the related sections.
The addressable memory space is divided into 8 main blocks, each of 512 MB.
All the memory areas that are not allocated to on-chip memories and peripherals are
considered “reserved”). Refer to the memory map figure in the corresponding product
datasheet.
Doc ID16188 Rev 5
35/713
45
Memory and bus architecture
2.3
RM0041
Memory map
See the datasheet corresponding to the used device for a comprehensive diagram of the
memory map. Table 1 and Table 2 give the boundary addresses of the peripherals available
in all STM32F100xx devices.
Table 1. Low and medium-density device register boundary addresses
Boundary address
Peripheral
Bus
Register map
0x4002 3000 - 0x4002 33FF
CRC
0x4002 2400 - 0x4002 2FFF
Reserved
-
0x4002 2000 - 0x4002 23FF
Flash memory interface
-
0x4002 1400 - 0x4002 1FFF
Reserved
0x4002 1000 - 0x4002 13FF
Reset and clock control RCC
0x4002 0400 - 0x4002 0FFF
Reserved
0x4002 0000 - 0x4002 03FF
DMA1
0x4001 4C00 - 0x4001 FFFF
Reserved
0x4001 4800 - 0x4001 4BFF
TIM17 timer
Section 15.6.16 on page 456
0x4001 4400 - 0x4001 47FF
TIM16 timer
Section 15.6.16 on page 456
0x4001 4000 - 0x4001 43FF
TIM15 timer
Section 15.5.18 on page 435
0x4001 3C00 - 0x4001 3FFF
Reserved
0x4001 3800 - 0x4001 3BFF
USART1
0x4001 3400 - 0x4001 37FF
Reserved
0x4001 3000 - 0x4001 33FF
SPI1
Section 21.4.8 on page 568
0x4001 2C00 - 0x4001 2FFF
TIM1 timer
Section 12.4.21 on page 280
0x4001 2800 - 0x4001 2BFF
Reserved
0x4001 2400 - 0x4001 27FF
ADC1
0x4001 1C00 - 0x4001 23FF
Reserved
0x4001 1800 - 0x4001 1BFF
GPIO Port E
Section 7.5 on page 128
0x4001 1400 - 0x4001 17FF
GPIO Port D
Section 7.5 on page 128
0x4001 1000 - 0x4001 13FF
GPIO Port C
Section 7.5 on page 128
0x4001 0C00 - 0x4001 0FFF
GPIO Port B
Section 7.5 on page 128
0x4001 0800 - 0x4001 0BFF
GPIO Port A
Section 7.5 on page 128
0x4001 0400 - 0x4001 07FF
EXTI
Section 8.3.7 on page 141
0x4001 0000 - 0x4001 03FF
AFIO
Section 7.5 on page 128
36/713
Section 3.4.4 on page 48
AHB
Section 6.3.12 on page 99
Section 9.4.7 on page 157
-
Section 23.6.8 on page 650
-
APB2
Section 10.11.15 on page 186
-
Doc ID16188 Rev 5
RM0041
Memory and bus architecture
Table 1. Low and medium-density device register boundary addresses (continued)
Boundary address
Peripheral
Bus
Register map
0x4000 7C00 - 0x4000 FFFF
Reserved
-
0x4000 7800 - 0x4000 7BFF
CEC
Section 24.9.8 on page 672
0x4000 7400 - 0x4000 77FF
DAC
Section 11.5.15 on page 208
0x4000 7000 - 0x4000 73FF
Power control PWR
Section 4.4.3 on page 62
0x4000 6C00 - 0x4000 6FFF
Backup registers (BKP)
Section 5.4.5 on page 67
0x4000 5C00 - 0x4000 6BFF
Reserved
0x4000 5800 - 0x4000 5BFF
I2C2
Section 22.6.10 on page 603
0x4000 5400 - 0x4000 57FF
I2C1
Section 22.6.10 on page 603
0x4000 4C00 - 0x4000 53FF
Reserved
0x4000 4800 - 0x4000 4BFF
USART3
Section 23.6.8 on page 650
0x4000 4400 - 0x4000 47FF
USART2
Section 23.6.8 on page 650
0x4000 3C00 - 0x4000 3FFF
Reserved
0x4000 3800 - 0x4000 3BFF
SPI2
0x4000 3400 - 0x4000 37FF
Reserved
0x4000 3000 - 0x4000 33FF
Independent watchdog (IWDG)
Section 18.4.5 on page 488
0x4000 2C00 - 0x4000 2FFF
Window watchdog (WWDG)
Section 19.6.4 on page 495
0x4000 2800 - 0x4000 2BFF
RTC
Section 17.4.7 on page 482
0x4000 1800 - 0x4000 27FF
Reserved
0x4000 1400 - 0x4000 17FF
TIM7 timer
Section 16.4.9 on page 470
0x4000 1000 - 0x4000 13FF
TIM6 timer
Section 16.4.9 on page 470
0x4000 0C00 - 0x4000 0FFF
Reserved
0x4000 0800 - 0x4000 0BFF
TIM4 timer
Section 13.4.19 on page 338
0x4000 0400 - 0x4000 07FF
TIM3 timer
Section 13.4.19 on page 338
0x4000 0000 - 0x4000 03FF
TIM2 timer
Section 13.4.19 on page 338
-
-
APB1
Section 21.4.8 on page 568
-
-
-
Table 2. High-density device register boundary addresses
Boundary address
Peripheral
Bus
Register map
0x4002 3000 - 0x4002 33FF
CRC
Section 3.4.4 on page 48
0x4002 2400 - 0x4002 2FFF
Reserved
-
0x4002 2000 - 0x4002 23FF
Flash memory interface
-
0x4002 1400 - 0x4002 1FFF
Reserved
0x4002 1000 - 0x4002 13FF
Reset and clock control RCC
0x4002 0800 - 0x4002 0FFF
Reserved
0x4002 0400 - 0x4002 07FF
DMA2
Section 9.4.7 on page 157
0x4002 0000 - 0x4002 03FF
DMA1
Section 9.4.7 on page 157
AHB
Section 6.3.12 on page 99
-
Doc ID16188 Rev 5
37/713
45
Memory and bus architecture
RM0041
Table 2. High-density device register boundary addresses (continued)
Boundary address
Peripheral
Bus
Register map
0x4001 4C00 - 0x4001 FFFF
Reserved
0x4001 4800 - 0x4001 4BFF
TIM17 timer
Section 15.6.16 on page 456
0x4001 4400 - 0x4001 47FF
TIM16 timer
Section 15.6.16 on page 456
0x4001 4000 - 0x4001 43FF
TIM15 timer
Section 15.5.18 on page 435
0x4001 3C00 - 0x4001 3FFF
Reserved
0x4001 3800 - 0x4001 3BFF
USART1
0x4001 3400 - 0x4001 37FF
Reserved
0x4001 3000 - 0x4001 33FF
SPI1
Section 21.4.8 on page 568
0x4001 2C00 - 0x4001 2FFF
TIM1 timer
Section 12.4.21 on page 280
0x4001 2800 - 0x4001 2BFF
Reserved
0x4001 2400 - 0x4001 27FF
ADC1
0x4001 2000 - 0x4001 23FF
GPIO Port G
Section 7.5 on page 128
0x4001 1C00 - 0x4001 1FFF
GPIO Port F
Section 7.5 on page 128
0x4001 1800 - 0x4001 1BFF
GPIO Port E
Section 7.5 on page 128
0x4001 1400 - 0x4001 17FF
GPIO Port D
Section 7.5 on page 128
0x4001 1000 - 0x4001 13FF
GPIO Port C
Section 7.5 on page 128
0x4001 0C00 - 0x4001 0FFF
GPIO Port B
Section 7.5 on page 128
0x4001 0800 - 0x4001 0BFF
GPIO Port A
Section 7.5 on page 128
0x4001 0400 - 0x4001 07FF
EXTI
Section 8.3.7 on page 141
0x4001 0000 - 0x4001 03FF
AFIO
Section 7.5 on page 128
38/713
-
Section 23.6.8 on page 650
-
APB2
Doc ID16188 Rev 5
Section 10.11.15 on page 186
RM0041
Memory and bus architecture
Table 2. High-density device register boundary addresses (continued)
Boundary address
Peripheral
Bus
Register map
0x4000 7C00 - 0x4000 FFFF
Reserved
0x4000 7800 - 0x4000 7BFF
CEC
Section 24.9.8 on page 672
0x4000 7400 - 0x4000 77FF
DAC
Section 11.5.15 on page 208
0x4000 7000 - 0x4000 73FF
Power control PWR
Section 4.4.3 on page 62
0x4000 6C00 - 0x4000 6FFF
Backup registers (BKP)
Section 5.4.5 on page 67
0x4000 5C00 - 0x4000 6BFF
Reserved
0x4000 5800 - 0x4000 5BFF
I2C2
Section 22.6.10 on page 603
0x4000 5400 - 0x4000 57FF
I2C1
Section 22.6.10 on page 603
0x4000 5000 - 0x4000 53FF
UART5
Section 23.6.8 on page 650
0x4000 4C00 - 0x4000 4FFF
UART4
Section 23.6.8 on page 650
0x4000 4800 - 0x4000 4BFF
USART3
Section 23.6.8 on page 650
0x4000 4400 - 0x4000 47FF
USART2
Section 23.6.8 on page 650
0x4000 4000 - 0x4000 43FF
Reserved
0x4000 3C00 - 0x4000 3FFF
SPI3
0x4000 3800 - 0x4000 3BFF
SPI2
0x4000 3400 - 0x4000 37FF
Reserved
0x4000 3000 - 0x4000 33FF
Independent watchdog (IWDG)
Section 18.4.5 on page 488
0x4000 2C00 - 0x4000 2FFF
Window watchdog (WWDG)
Section 18.4.5 on page 488
0x4000 2800 - 0x4000 2BFF
RTC
Section 17.4.7 on page 482
0x4000 2400 - 0x4000 27FF
Reserved
0x4000 2000 - 0x4000 23FF
TIM14 timer
Section 14.5.11 on page 387
0x4000 1C00 - 0x4000 1FFF
TIM13 timer
Section 14.5.11 on page 387
0x4000 1800 - 0x4000 1BFF
TIM12 timer
Section 14.4.14 on page 377
0x4000 1400 - 0x4000 17FF
TIM7 timer
Section 16.4.9 on page 470
0x4000 1000 - 0x4000 13FF
TIM6 timer
Section 16.4.9 on page 470
0x4000 0C00 - 0x4000 0FFF
TIM5 timer
Section 13.4.19 on page 338
0x4000 0800 - 0x4000 0BFF
TIM4 timer
Section 13.4.19 on page 338
0x4000 0400 - 0x4000 07FF
TIM3 timer
Section 13.4.19 on page 338
0x4000 0000 - 0x4000 03FF
TIM2 timer
Section 13.4.19 on page 338
2.3.1
-
-
Section 21.4.8 on page 568
APB1
Section 21.4.8 on page 568
-
-
Embedded SRAM
The STM32F100xx features up to 32 Kbytes of static SRAM. It can be accessed as bytes,
half-words (16 bits) or full words (32 bits). The SRAM start address is 0x2000 0000.
Doc ID16188 Rev 5
39/713
45
Memory and bus architecture
2.3.2
RM0041
Bit banding
The Cortex®-M3 memory map includes two bit-band regions. These regions map each word
in an alias region of memory to a bit in a bit-band region of memory. Writing to a word in the
alias region has the same effect as a read-modify-write operation on the targeted bit in the
bit-band region.
In the STM32F100xx, both peripheral registers and SRAM are mapped in a bit-band region.
This allows single bit-band write and read operations to be performed.
A mapping formula shows how to reference each word in the alias region to a corresponding
bit in the bit-band region. The mapping formula is:
bit_word_addr = bit_band_base + (byte_offset x 32) + (bit_number × 4)
where:
bit_word_addr is the address of the word in the alias memory region that maps to the
targeted bit
bit_band_base is the starting address of the alias region
byte_offset is the number of the byte in the bit-band region that contains the targeted
bit
bit_number is the bit position (0-7) of the targeted bit
Example:
The following example shows how to map bit 2 of the byte located at SRAM address
0x2000 0300 in the alias region:
0x2200 6008 = 0x2200 0000 + (0x300*32) + (2*4).
Writing to address 0x2200 6008 has the same effect as a read-modify-write operation on bit
2 of the byte at SRAM address 0x2000 0300.
Reading address 0x2200 6008 returns the value (0x01 or 0x00) of bit 2 of the byte at SRAM
address 0x2000 0300 (0x01: bit set; 0x00: bit cleared).
For more information on bit-banding, refer to the Cortex®-M3 Technical Reference Manual.
2.3.3
Embedded Flash memory
The high-performance Flash memory module has the following key features:
•
Density of up to 512 Kbytes
•
Memory organization: the Flash memory is organized as a main block and an
information block:
–
Main memory block of size:
up to 8 Kbit × 32 bits divided into 32 pages of 1 Kbyte each for low-density value
line devices (see Table 3)
up to 32 Kbit × 32 bits divided into 128 pages of 1 Kbyte each for medium-density
value line devices (see Table 4)
up to 128 Kbit × 32 bits divided into 256 pages of 2 Kbyte each for high-density
value line devices (see Table 5)
–
40/713
Information block of size:
516 × 32 bits for low, medium and high-density value line devices (see Table 3,
Table 4 and Table 5)
Doc ID16188 Rev 5
RM0041
Memory and bus architecture
The Flash memory interface (FLASH) features:
•
Read interface (32-bit)
•
Option byte loader
•
Flash Program / Erase operation
•
Read / write protection
Table 3. Flash module organization (low-density value line devices)
Block
Main memory
Information block
Flash memory
interface
registers
Name
Base addresses
Size (bytes)
Page 0
0x0800 0000 - 0x0800 03FF
1 Kbyte
Page 1
0x0800 0400 - 0x0800 07FF
1 Kbyte
Page 2
0x0800 0800 - 0x0800 0BFF
1 Kbyte
Page 3
0x0800 0C00 - 0x0800 0FFF
1 Kbyte
Page 4
0x0800 1000 - 0x0800 13FF
1 Kbyte
.
.
.
.
.
.
.
.
.
Page 31
0x0800 7C00 - 0x0800 8000
1 Kbyte
System memory
0x1FFF F000 - 0x1FFF F7FF
2 Kbytes
Option Bytes
0x1FFF F800 - 0x1FFF F80F
16
FLASH_ACR
0x4002 2000 - 0x4002 2003
4
FLASH_KEYR
0x4002 2004 - 0x4002 2007
4
FLASH_OPTKEYR
0x4002 2008 - 0x4002 200B
4
FLASH_SR
0x4002 200C - 0x4002 200F
4
FLASH_CR
0x4002 2010 - 0x4002 2013
4
FLASH_AR
0x4002 2014 - 0x4002 2017
4
Reserved
0x4002 2018 - 0x4002 201B
4
FLASH_OBR
0x4002 201C - 0x4002 201F
4
FLASH_WRPR
0x4002 2020 - 0x4002 2023
4
Doc ID16188 Rev 5
41/713
45
Memory and bus architecture
RM0041
Table 4. Flash module organization (medium-density value line devices)
Block
Main memory
Information block
Flash memory
interface
registers
Name
Base addresses
Size (bytes)
Page 0
0x0800 0000 - 0x0800 03FF
1 Kbyte
Page 1
0x0800 0400 - 0x0800 07FF
1 Kbyte
Page 2
0x0800 0800 - 0x0800 0BFF
1 Kbyte
Page 3
0x0800 0C00 - 0x0800 0FFF
1 Kbyte
Page 4
0x0800 1000 - 0x0800 13FF
1 Kbyte
.
.
.
.
.
.
.
.
.
Page 127
0x0801 FC00 - 0x0801 FFFF
1 Kbyte
System memory
0x1FFF F000 - 0x1FFF F7FF
2 Kbytes
Option Bytes
0x1FFF F800 - 0x1FFF F80F
16
FLASH_ACR
0x4002 2000 - 0x4002 2003
4
FLASH_KEYR
0x4002 2004 - 0x4002 2007
4
FLASH_OPTKEYR
0x4002 2008 - 0x4002 200B
4
FLASH_SR
0x4002 200C - 0x4002 200F
4
FLASH_CR
0x4002 2010 - 0x4002 2013
4
FLASH_AR
0x4002 2014 - 0x4002 2017
4
Reserved
0x4002 2018 - 0x4002 201B
4
FLASH_OBR
0x4002 201C - 0x4002 201F
4
FLASH_WRPR
0x4002 2020 - 0x4002 2023
4
Table 5. Flash module organization (high-density value line devices)
Block
Main memory
Information block
42/713
Name
Base addresses
Size (bytes)
Page 0
0x0800 0000 - 0x0800 07FF
2 Kbytes
Page 1
0x0800 0800 - 0x0800 0FFF
2 Kbytes
Page 2
0x0800 1000 - 0x0800 17FF
2 Kbytes
Page 3
0x0800 1800 - 0x0800 1FFF
2 Kbytes
.
.
.
.
.
.
.
.
.
Page 255
0x0807 F800 - 0x0807 FFFF
2 Kbytes
System memory
0x1FFF F000 - 0x1FFF F7FF
2 Kbytes
Option Bytes
0x1FFF F800 - 0x1FFF F80F
16
Doc ID16188 Rev 5
RM0041
Memory and bus architecture
Table 5. Flash module organization (high-density value line devices) (continued)
Block
Flash memory
interface
registers
Note:
Name
Base addresses
Size (bytes)
FLASH_ACR
0x4002 2000 - 0x4002 2003
4
FLASH_KEYR
0x4002 2004 - 0x4002 2007
4
FLASH_OPTKEYR
0x4002 2008 - 0x4002 200B
4
FLASH_SR
0x4002 200C - 0x4002 200F
4
FLASH_CR
0x4002 2010 - 0x4002 2013
4
FLASH_AR
0x4002 2014 - 0x4002 2017
4
Reserved
0x4002 2018 - 0x4002 201B
4
FLASH_OBR
0x4002 201C - 0x4002 201F
4
FLASH_WRPR
0x4002 2020 - 0x4002 2023
4
For further information on the Flash memory interface registers, refer to the STM32F100xx
Flash programming manual (PM0063).
Reading Flash memory
Flash memory accesses are performed through the AHB bus. Accesses are either
instruction fetches over the ICode bus, or data accesses (e.g. literal pool) over the D-code
bus. Since these two buses have the same Flash memory as target, the interface gives
priority to D-code bus accesses over I-code bus, instruction fetch accesses.
Read accesses can be performed without any wait state and with the following configuration
options:
•
Note:
Half cycle: for power optimization
1
Half cycle configuration is not available in combination with a prescaler on the AHB. The
system clock (SYSCLK) should be equal to the HCLK clock. This feature can therefore be
used only with a low-frequency clock of 8 MHz or less. It can be generated from the HSI or
the HSE but not from the PLL.
2
Using DMA: DMA accesses Flash memory on the DCode bus and has priority over ICode
instructions. The DMA provides one free cycle after each transfer. Some instructions can be
performed together with DMA transfer.
Programming and erasing Flash memory
The Flash memory can be programmed 16 bits (half words) at a time. For write and erase
operations on the Flash memory (write/erase), the internal RC oscillator (HSI) must be ON.
The Flash memory erase operation can be performed at page level or on the whole Flash
area (mass erase). Mass erase does not affect the information blocks.
To ensure that there is no overprogramming, the Flash programming and erase controller
blocks are clocked by a fixed clock.
The end of write operation (programming or erasing) can trigger an interrupt. This interrupt
can be used to exit the WFI mode, only if the FLASH clock is enabled. Otherwise, the
interrupt is served only after exiting WFI.
The FLASH_ACR register is used to enable/disable Flash memory half-cycle access. The
tables below provide the bit map and bit descriptions for this register.
Doc ID16188 Rev 5
43/713
45
Memory and bus architecture
RM0041
For complete information on Flash memory operations and register configurations, refer to
the STM32F100xx Flash programming manual (PM0063).
Flash access control register (FLASH_ACR)
Address offset: 0x00
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
20
6
5
4
19
18
17
16
3
2
1
0
Reserved
7
HLFCYA
Reserved
Reserved
rw
Reserved, must be kept cleared.
Bits 31:4
Bit 3 HLFCYA: Flash half cycle access enable
0: Half cycle is disabled
1: Half cycle is enabled
Reserved, must be kept cleared.
Bits 2:0
2.4
Boot configuration
In the STM32F100xx, three different boot modes can be selected through the BOOT[1:0]
pins as shown in Table 6.
Table 6. Boot modes
Boot mode selection pins
Boot mode
Aliasing
BOOT1
BOOT0
x
0
Main Flash memory Main Flash memory is selected as the boot space
0
1
System memory
System memory is selected as the boot space
1
1
Embedded SRAM
Embedded SRAM is selected as the boot space
The values on the BOOT pins are latched on the 4th rising edge of SYSCLK after a reset. It
is up to the application to set the BOOT1 and BOOT0 pins after reset to select the required
boot mode.
The BOOT pins are also resampled when exiting the Standby mode. Consequently, they
must be kept in the required boot mode configuration in the Standby mode. After this startup
delay has elapsed, the CPU fetches the top-of-stack value from address 0x0000 0000, then
starts code execution from the boot memory starting from 0x0000 0004.
Due to its fixed memory map, the code area starts from address 0x0000 0000 (accessed
through the ICode/DCode buses) while the data area (SRAM) starts from address
0x2000 0000 (accessed through the system bus). The Cortex-M3 CPU always fetches the
reset vector on the ICode bus, which implies to have the boot space available only in the
code area (typically, Flash memory). STM32F100xx microcontrollers implement a special
mechanism to be able to boot also from SRAM and not only from main Flash memory and
System memory.
44/713
Doc ID16188 Rev 5
RM0041
Memory and bus architecture
Depending on the boot mode selected, the main Flash memory, system memory or SRAM is
accessible as follows:
Note:
•
Boot from main Flash memory: the main Flash memory is aliased in the boot memory
space (0x0000 0000), but still accessible from its original memory space (0x800 0000).
In other words, the Flash memory contents can be accessed starting from address
0x0000 0000 or 0x800 0000.
•
Boot from system memory: the system memory is aliased in the boot memory space
(0x0000 0000), but still accessible from its original memory space (0x1FFF F000).
•
Boot from the embedded SRAM: SRAM is accessible only at address 0x2000 0000.
When booting from SRAM, in the application initialization code, the vector table in SRAM
must be relocated using the NVIC exception table and offset register.
Embedded boot loader
The embedded boot loader is used to reprogram the Flash memory using the USART1
serial interface. This program is located in the system memory and is programmed by ST
during production. For further details refer to AN2606.
Doc ID16188 Rev 5
45/713
45
CRC calculation unit
3
RM0041
CRC calculation unit
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
3.1
CRC introduction
The CRC (cyclic redundancy check) calculation unit is used to get a CRC code from a 32-bit
data word and a fixed generator polynomial.
Among other applications, CRC-based techniques are used to verify data transmission or
storage integrity. In the scope of the EN/IEC 60335-1 standard, they offer a means of
verifying the Flash memory integrity. The CRC calculation unit helps compute a signature of
the software during runtime, to be compared with a reference signature generated at linktime and stored at a given memory location.
3.2
CRC main features
•
Uses CRC-32 (Ethernet) polynomial: 0x4C11DB7
–
•
X32 + X26 + X23 + X22 + X16 + X12 + X11 + X10 +X8 + X7 + X5 + X4 + X2+ X + 1
Single input/output 32-bit data register
•
CRC computation done in 4 AHB clock cycles (HCLK)
•
General-purpose 8-bit register (can be used for temporary storage)
The block diagram is shown in Figure 3.
Figure 3. CRC calculation unit block diagram
$+%EXV
ELWUHDGDFFHVV
'DWDUHJLVWHURXWSXW
&5&FRPSXWDWLRQSRO\QRPLDO[&'%
ELWZULWHDFFHVV
'DWDUHJLVWHULQSXW
DL
46/713
Doc ID16188 Rev 5
RM0041
CRC calculation unit
3.3
CRC functional description
The CRC calculation unit mainly consists of a single 32-bit data register, which:
•
is used as an input register to enter new data in the CRC calculator (when writing into
the register)
•
holds the result of the previous CRC calculation (when reading the register)
Each write operation into the data register creates a combination of the previous CRC value
and the new one (CRC computation is done on the whole 32-bit data word, and not byte per
byte).
The write operation is stalled until the end of the CRC computation, thus allowing back-toback write accesses or consecutive write and read accesses.
The CRC calculator can be reset to 0xFFFF FFFF with the RESET control bit in the
CRC_CR register. This operation does not affect the contents of the CRC_IDR register.
3.4
CRC registers
The CRC calculation unit contains two data registers and a control register.The peripheral
The CRC registers have to be accessed by words (32 bits).
3.4.1
Data register (CRC_DR)
Address offset: 0x00
Reset value: 0xFFFF FFFF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
DR [31:16]
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
DR [15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 31:0 Data register bits
Used as an input register when writing new data into the CRC calculator.
Holds the previous CRC calculation result when it is read.
3.4.2
Independent data register (CRC_IDR)
Address offset: 0x04
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
Reserved
15
14
13
12
11
Reserved
10
9
8
IDR[7:0]
Doc ID16188 Rev 5
rw
47/713
48
CRC calculation unit
RM0041
Bits 31:8 Reserved, must be kept at reset value.
Bits 7:0 General-purpose 8-bit data register bits
Can be used as a temporary storage location for one byte.
This register is not affected by CRC resets generated by the RESET bit in the CRC_CR
register.
3.4.3
Control register (CRC_CR)
Address offset: 0x08
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
6
5
4
3
2
1
16
Reserved
15
14
13
12
11
10
9
8
7
0
RESET
Reserved
w
Bits 31:1 Reserved, must be kept at reset value.
Bit 0 RESET bit
Resets the CRC calculation unit and sets the data register to 0xFFFF FFFF.
This bit can only be set, it is automatically cleared by hardware.
3.4.4
CRC register map
The following table provides the CRC register map and reset values.
Table 7. CRC calculation unit register map and reset values
Offset
0x00
Register
31-24
23-16
15-8
7
6
Data register
Reset
value
0xFFFF FFFF
Reset
value
48/713
Reset
value
3
2
1
0
Independent data register
Reserved
0x00
CRC_CR
0x08
4
CRC_DR
CRC_IDR
0x04
5
RESET
Reserved
Doc ID16188 Rev 5
0
RM0041
4
Power control (PWR)
Power control (PWR)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
4.1
Power supplies
The device requires a 2.0-to-3.6 V operating voltage supply (VDD). An embedded regulator
is used to supply the internal 1.8 V digital power.
The real-time clock (RTC) and backup registers can be powered from the VBAT voltage
when the main VDD supply is powered off.
Figure 4. Power supply overview
VDDA domain
(VSSA) VREF(from 2.4 V up to VDDA)VREF+
A/D converter
D/A converter
Temp. sensor
Reset block
PLL
(VDD) VDDA
(VSS) VSSA
VDD domain
I/O Ring
VSS
VDD
Standby circuitry
(Wakeup logic,
IWDG)
1.8 V domain
Core
Memories
digital
peripherals
Voltage Regulator
Low voltage detector
Backup domain
VBAT
LSE crystal 32K osc
BKP registers
RCC BDCR register
RTC
1. VDDA and VSSA must be connected to VDD and VSS, respectively.
Doc ID16188 Rev 5
49/713
62
Power control (PWR)
4.1.1
RM0041
Independent A/D and D/A converter supply and reference voltage
To improve conversion accuracy, the ADC and the DAC have an independent power supply
which can be separately filtered and shielded from noise on the PCB.
•
The ADC and DAC voltage supply input is available on a separate VDDA pin.
•
An isolated supply ground connection is provided on pin VSSA.
When available (according to package), VREF- must be tied to VSSA.
On 100-pin packages
To ensure a better accuracy on low-voltage inputs and outputs, the user can connect a
separate external reference voltage on VREF+. VREF+ is the highest voltage, represented by
the full scale value, for an analog input (ADC) or output (DAC) signal. The voltage on VREF+
can range from 2.4 V to VDDA.
On 64-pin packages and packages with less pins
The VREF+ and VREF- pins are not available, they are internally connected to the ADC
voltage supply (VDDA) and ground (VSSA).
4.1.2
Battery backup domain
To retain the content of the Backup registers and supply the RTC function when VDD is
turned off, VBAT pin can be connected to an optional standby voltage supplied by a battery
or by another source.
The VBAT pin powers the RTC unit, the LSE oscillator and the PC13 to PC15 IOs, allowing
the RTC to operate even when the main digital supply (VDD) is turned off. The switch to the
VBAT supply is controlled by the Power Down Reset embedded in the Reset block.
Warning:
During tRSTTEMPO (temporization at VDD startup) or after a PDR
is detected, the power switch between VBAT and VDD remains
connected to VBAT.
During the startup phase, if VDD is established in less than
tRSTTEMPO (Refer to the datasheet for the value of tRSTTEMPO)
and VDD > VBAT + 0.6 V, a current may be injected into VBAT
through an internal diode connected between VDD and the
power switch (VBAT).
If the power supply/battery connected to the VBAT pin cannot
support this current injection, it is strongly recommended to
connect an external low-drop diode between this power
supply and the VBAT pin.
If no external battery is used in the application, it is recommended to connect VBAT
externally to VDD with a 100 nF external ceramic decoupling capacitor (for more details refer
to AN2586).
50/713
Doc ID16188 Rev 5
RM0041
Power control (PWR)
When the backup domain is supplied by VDD (analog switch connected to VDD), the
following functions are available:
Note:
•
PC14 and PC15 can be used as either GPIO or LSE pins
•
PC13 can be used as GPIO, TAMPER pin, RTC Calibration Clock, RTC Alarm or
second output (refer to Section 5: Backup registers (BKP))
Due to the fact that the switch only sinks a limited amount of current (3 mA), the use of
GPIOs PC13 to PC15 in output mode is restricted: the speed has to be limited to 2 MHz with
a maximum load of 30 pF and these IOs must not be used as a current source (e.g. to drive
a LED).
When the backup domain is supplied by VBAT (analog switch connected to VBAT because
VDD is not present), the following functions are available:
4.1.3
•
PC14 and PC15 can be used as LSE pins only
•
PC13 can be used as TAMPER pin, RTC Alarm or Second output (refer to
Section 5.4.2: RTC clock calibration register (BKP_RTCCR)).
Voltage regulator
The voltage regulator is always enabled after Reset. It works in three different modes
depending on the application modes.
•
In Run mode, the regulator supplies full power to the 1.8 V domain (core, memories
and digital peripherals).
•
In Stop mode the regulator supplies low-power to the 1.8 V domain, preserving
contents of registers and SRAM
•
In Standby Mode, the regulator is powered off. The contents of the registers and SRAM
are lost except for the Standby circuitry and the Backup Domain.
4.2
Power supply supervisor
4.2.1
Power on reset (POR)/power down reset (PDR)
The device has an integrated POR/PDR circuitry that allows proper operation starting
from/down to 2 V.
The device remains in Reset mode when VDD/VDDA is below a specified threshold,
VPOR/PDR, without the need for an external reset circuit. For more details concerning the
power on/power down reset threshold, refer to the electrical characteristics of the datasheet.
Doc ID16188 Rev 5
51/713
62
Power control (PWR)
RM0041
Figure 5. Power on reset/power down reset waveform
9''9''$
93253'5
ULVLQJHGJH
93253'5
IDOOLQJHGJH
3'5
P9
K\VWHUHVLV
3'5
7HPSRUL]DWLRQ
W5677(032
5HVHW
069
4.2.2
Programmable voltage detector (PVD)
The PVD can be used to monitor the VDD/VDDA power supply by comparing it to a threshold
selected by the PLS[2:0] bits in the Power control register (PWR_CR).
The PVD is enabled by setting the PVDE bit.
A PVDO flag is available, in the Power control/status register (PWR_CSR), to indicate if
VDD/VDDA is higher or lower than the PVD threshold. This event is internally connected to
the EXTI line16 and can generate an interrupt if enabled through the EXTI registers. The
PVD output interrupt can be generated when VDD/VDDA drops below the PVD threshold
and/or when VDD/VDDA rises above the PVD threshold depending on EXTI line16
rising/falling edge configuration. As an example the service routine could perform
emergency shutdown tasks.
52/713
Doc ID16188 Rev 5
RM0041
Power control (PWR)
Figure 6. PVD thresholds
9''
39'WKUHVKROG
P9
K\VWHUHVLV
39'RXWSXW
069
Doc ID16188 Rev 5
53/713
62
Power control (PWR)
4.3
RM0041
Low-power modes
By default, the microcontroller is in Run mode after a system or a power Reset. Several lowpower modes are available to save power when the CPU does not need to be kept running,
for example when waiting for an external event. It is up to the user to select the mode that
gives the best compromise between low-power consumption, short startup time and
available wakeup sources.
The STM32F100xx devices feature three low-power modes:
•
Sleep mode (CPU clock off, all peripherals including Cortex®-M3 core peripherals like
NVIC, SysTick, etc. are kept running)
•
Stop mode (all clocks are stopped)
•
Standby mode (1.8V domain powered-off)
In addition, the power consumption in Run mode can be reduce by one of the following
means:
•
Slowing down the system clocks
•
Gating the clocks to the APB and AHB peripherals when they are unused.
Table 8. Low-power mode summary
Mode name
Entry
Sleep
WFI
(Sleep now or
Sleep-on WFE
exit)
Stop
Standby
4.3.1
wakeup
Any interrupt
Wakeup event
PDDS and LPDS
Any EXTI line
bits +
(configured in the
SLEEPDEEP bit
EXTI registers)
+ WFI or WFE
PDDS bit +
SLEEPDEEP bit
+ WFI or WFE
WKUP pin rising
edge, RTC alarm,
external reset in
NRST pin,
IWDG reset
Effect on 1.8V
domain clocks
Effect on
VDD
domain
clocks
CPU clock OFF
no effect on other None
clocks or analog
clock sources
All 1.8V domain
clocks OFF
HSI and
HSE
oscillators
OFF
Voltage
regulator
ON
ON or in lowpower mode
(depends on
Power control
register
(PWR_CR))
OFF
Slowing down system clocks
In Run mode the speed of the system clocks (SYSCLK, HCLK, PCLK1, PCLK2) can be
reduced by programming the prescaler registers. These prescalers can also be used to slow
down peripherals before entering Sleep mode.
For more details refer to Section 7.3.2: Clock configuration register (RCC_CFGR).
54/713
Doc ID16188 Rev 5
RM0041
4.3.2
Power control (PWR)
Peripheral clock gating
In Run mode, the HCLK and PCLKx for individual peripherals and memories can be stopped
at any time to reduce power consumption.
To further reduce power consumption in Sleep mode the peripheral clocks can be disabled
prior to executing the WFI or WFE instructions.
Peripheral clock gating is controlled by the , APB1 peripheral clock enable register
(RCC_APB1ENR) and APB2 peripheral clock enable register (RCC_APB2ENR).
4.3.3
Sleep mode
Entering Sleep mode
The Sleep mode is entered by executing the WFI (Wait For Interrupt) or WFE (Wait for
Event) instructions. Two options are available to select the Sleep mode entry mechanism,
depending on the SLEEPONEXIT bit in the Cortex®-M3 System Control register:
•
Sleep-now: if the SLEEPONEXIT bit is cleared, the MCU enters Sleep mode as soon
as WFI or WFE instruction is executed.
•
Sleep-on-exit: if the SLEEPONEXIT bit is set, the MCU enters Sleep mode as soon as
it exits the lowest priority ISR.
In the Sleep mode, all I/O pins keep the same state as in the Run mode.
Refer to Table 9 and Table 10 for details on how to enter Sleep mode.
Exiting Sleep mode
If the WFI instruction is used to enter Sleep mode, any peripheral interrupt acknowledged by
the nested vectored interrupt controller (NVIC) can wake up the device from Sleep mode.
If the WFE instruction is used to enter Sleep mode, the MCU exits Sleep mode as soon as
an event occurs. The wakeup event can be generated either by:
•
enabling an interrupt in the peripheral control register but not in the NVIC, and enabling
the SEVONPEND bit in the Cortex®-M3 System Control register. When the MCU
resumes from WFE, the peripheral interrupt pending bit and the peripheral NVIC IRQ
channel pending bit (in the NVIC interrupt clear pending register) have to be cleared.
•
or configuring an external or internal EXTI line in event mode. When the CPU resumes
from WFE, it is not necessary to clear the peripheral interrupt pending bit or the NVIC
IRQ channel pending bit as the pending bit corresponding to the event line is not set.
This mode offers the lowest wakeup time as no time is wasted in interrupt entry/exit.
Refer to Table 9 and Table 10 for more details on how to exit Sleep mode.
Doc ID16188 Rev 5
55/713
62
Power control (PWR)
RM0041
Table 9. Sleep-now
Sleep-now mode
Description
Mode entry
WFI (Wait for Interrupt) or WFE (Wait for Event) while:
– SLEEPDEEP = 0 and
– SLEEPONEXIT = 0
Refer to the Cortex®-M3 System Control register.
Mode exit
If WFI was used for entry:
Interrupt: Refer to Table 50: Vector table for STM32F100xx devices
If WFE was used for entry
Wakeup event: Refer to Section 8.2.3: Wakeup event management
Wakeup latency
None
Table 10. Sleep-on-exit
Sleep-on-exit
4.3.4
Description
Mode entry
WFI (wait for interrupt) while:
– SLEEPDEEP = 0 and
– SLEEPONEXIT = 1
Refer to the Cortex®-M3 System Control register.
Mode exit
Interrupt: refer to Table 50: Vector table for STM32F100xx devices.
Wakeup latency
None
Stop mode
The Stop mode is based on the Cortex®-M3 deepsleep mode combined with peripheral
clock gating. The voltage regulator can be configured either in normal or low-power mode.
In Stop mode, all clocks in the 1.8 V domain are stopped, the PLL, the HSI and the HSE RC
oscillators are disabled. SRAM and register contents are preserved.
In the Stop mode, all I/O pins keep the same state as in the Run mode.
Entering Stop mode
Refer to Table 11 for details on how to enter the Stop mode.
To further reduce power consumption in Stop mode, the internal voltage regulator can be put
in low-power mode. This is configured by the LPDS bit of the Power control register
(PWR_CR).
If Flash memory programming is ongoing, the Stop mode entry is delayed until the memory
access is finished.
If an access to the APB domain is ongoing, The Stop mode entry is delayed until the APB
access is finished.
56/713
Doc ID16188 Rev 5
RM0041
Power control (PWR)
In Stop mode, the following features can be selected by programming individual control bits:
•
Independent watchdog (IWDG): the IWDG is started by writing to its Key register or by
hardware option. Once started it cannot be stopped except by a Reset. See
Section 18.3: IWDG functional description.
•
Real-time clock (RTC): this is configured by the RTCEN bit in the Backup domain
control register (RCC_BDCR)
•
Internal RC oscillator (LSI RC): this is configured by the LSION bit in the Control/status
register (RCC_CSR).
•
External 32.768 kHz oscillator (LSE OSC): this is configured by the LSEON bit in the
Backup domain control register (RCC_BDCR).
The ADC or DAC can also consume power during the Stop mode, unless they are disabled
before entering it. To disable them, the ADON bit in the ADC_CR2 register and the ENx bit
in the DAC_CR register must both be written to 0.
Note:
If the application needs to disable the external clock before entering Stop mode, the HSEON
bit must first be disabled and the system clock switched to HSI. Otherwise, if the HSEON bit
remains enabled and the external clock (external oscillator) is removed when entering Stop
mode, the clock security system (CSS) feature must be enabled to detect any external
oscillator failure and avoid a malfunction behavior when entering stop mode.
Exiting Stop mode
Refer to Table 11 for more details on how to exit Stop mode.
When exiting Stop mode by issuing an interrupt or a wakeup event, the HSI RC oscillator is
selected as system clock.
When the voltage regulator operates in low-power mode, an additional startup delay is
incurred when waking up from Stop mode. By keeping the internal regulator ON during Stop
mode, the consumption is higher although the startup time is reduced.
Table 11. Stop mode
Stop mode
Mode entry
Description
WFI (Wait for Interrupt) or WFE (Wait for Event) while:
– Set SLEEPDEEP bit in Cortex®-M3 System Control register
– Clear PDDS bit in Power Control register (PWR_CR)
– Select the voltage regulator mode by configuring LPDS bit in PWR_CR
Note: To enter Stop mode, all EXTI Line pending bits (in Pending register
(EXTI_PR)), all peripheral interrupt pending bits, and RTC Alarm flag must
be reset. Otherwise, the Stop mode entry procedure is ignored and
program execution continues.
Mode exit
If WFI was used for entry:
Any EXTI Line configured in Interrupt mode (the corresponding EXTI
Interrupt vector must be enabled in the NVIC). Refer to Table 50: Vector
table for STM32F100xx devices.
If WFE was used for entry:
Any EXTI Line configured in event mode. Refer to Section 8.2.3: Wakeup
event management
Wakeup latency
HSI RC wakeup time + regulator wakeup time from Low-power mode
Doc ID16188 Rev 5
57/713
62
Power control (PWR)
4.3.5
RM0041
Standby mode
The Standby mode allows to achieve the lowest power consumption. It is based on the
Cortex®-M3 deepsleep mode, with the voltage regulator disabled. The 1.8 V domain is
consequently powered off. The PLL, the HSI oscillator and the HSE oscillator are also
switched off. SRAM and register contents are lost except for registers in the Backup domain
and Standby circuitry (see Figure 4).
Entering Standby mode
Refer to Table 12 for more details on how to enter Standby mode.
In Standby mode, the following features can be selected by programming individual control
bits:
•
Independent watchdog (IWDG): the IWDG is started by writing to its Key register or by
hardware option. Once started it cannot be stopped except by a reset. See
Section 18.3: IWDG functional description.
•
Real-time clock (RTC): this is configured by the RTCEN bit in the Backup domain
control register (RCC_BDCR)
•
Internal RC oscillator (LSI RC): this is configured by the LSION bit in the Control/status
register (RCC_CSR).
•
External 32.768 kHz oscillator (LSE OSC): this is configured by the LSEON bit in the
Backup domain control register (RCC_BDCR)
Exiting Standby mode
The microcontroller exits the Standby mode when an external reset (NRST pin), an IWDG
reset, a rising edge on the WKUP pin or the rising edge of an RTC alarm occurs (see
Figure 196: RTC simplified block diagram). All registers are reset after wakeup from
Standby except for Power control/status register (PWR_CSR).
After waking up from Standby mode, program execution restarts in the same way as after a
Reset (boot pins sampling, vector reset is fetched, etc.). The SBF status flag in the Power
control/status register (PWR_CSR) indicates that the MCU was in Standby mode.
Refer to Table 12 for more details on how to exit Standby mode.
Table 12. Standby mode
Standby mode
58/713
Description
Mode entry
WFI (Wait for Interrupt) or WFE (Wait for Event) while:
– Set SLEEPDEEP in Cortex®-M3 System Control register
– Set PDDS bit in Power Control register (PWR_CR)
– Clear WUF bit in Power Control/Status register (PWR_CSR)
– No interrupt (for WFI) or event (for WFI) is pending
Mode exit
WKUP pin rising edge, RTC alarm event’s rising edge, external Reset in
NRST pin, IWDG Reset.
Wakeup latency
Reset phase
Doc ID16188 Rev 5
RM0041
Power control (PWR)
I/O states in Standby mode
In Standby mode, all I/O pins are high impedance except:
•
Reset pad (still available)
•
TAMPER pin if configured for tamper or calibration out
•
WKUP pin, if enabled
Debug mode
By default, the debug connection is lost if the application puts the MCU in Stop or Standby
mode while the debug features are used. This is due to the fact that the Cortex®-M3 core is
no longer clocked.
However, by setting some configuration bits in the DBGMCU_CR register, the software can
be debugged even when using the low-power modes extensively. For more details, refer to
Section 25.15.1: Debug support for low-power modes.
4.3.6
Auto-wakeup (AWU) from low-power mode
The RTC can be used to wakeup the MCU from low-power mode without depending on an
external interrupt (Auto-wakeup mode). The RTC provides a programmable time base for
waking up from Stop or Standby mode at regular intervals. For this purpose, two of the three
alternative RTC clock sources can be selected by programming the RTCSEL[1:0] bits in the
Backup domain control register (RCC_BDCR):
•
Low-power 32.768 kHz external crystal oscillator (LSE OSC).
This clock source provides a precise time base with very low-power consumption (less
than 1µA added consumption in typical conditions)
•
Low-power internal RC Oscillator (LSI RC)
This clock source has the advantage of saving the cost of the 32.768 kHz crystal. This
internal RC Oscillator is designed to add minimum power consumption.
To wakeup from Stop mode with an RTC alarm event, it is necessary to:
•
Configure the EXTI Line 17 to be sensitive to rising edge
•
Configure the RTC to generate the RTC alarm
To wakeup from Standby mode, there is no need to configure the EXTI Line 17.
4.4
Power control registers
The peripheral registers can be accessed by half-words (16-bit) or words (32-bit).
4.4.1
Power control register (PWR_CR)
Address offset: 0x00
Reset value: 0x0000 0000 (reset by wakeup from Standby mode)
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
PVDE
CSBF
CWUF
PDDS
LPDS
rw
rc_w1
rc_w1
rw
rw
Reserved
15
14
13
12
11
10
9
8
7
DBP
PLS[2:0]
Reserved
rw
rw
Doc ID16188 Rev 5
rw
rw
59/713
62
Power control (PWR)
Bits 31:9
RM0041
Reserved, must be kept at reset value..
Bit 8 DBP: Disable backup domain write protection.
In reset state, the RTC and backup registers are protected against parasitic write access.
This bit must be set to enable write access to these registers.
0: Access to RTC and Backup registers disabled
1: Access to RTC and Backup registers enabled
Note: If the HSE divided by 128 is used as the RTC clock, this bit must remain set to 1.
Bits 7:5 PLS[2:0]: PVD level selection.
These bits are written by software to select the voltage threshold detected by the Power
Voltage Detector
000: 2.2V
001: 2.3V
010: 2.4V
011: 2.5V
100: 2.6V
101: 2.7V
110: 2.8V
111: 2.9V
Note: Refer to the electrical characteristics of the datasheet for more details.
Bit 4 PVDE: Power voltage detector enable.
This bit is set and cleared by software.
0: PVD disabled
1: PVD enabled
Bit 3 CSBF: Clear standby flag.
This bit is always read as 0.
0: No effect
1: Clear the SBF Standby Flag (write).
Bit 2 CWUF: Clear wakeup flag.
This bit is always read as 0.
0: No effect
1: Clear the WUF Wakeup Flag after 2 System clock cycles. (write)
Bit 1 PDDS: Power down deepsleep.
This bit is set and cleared by software. It works together with the LPDS bit.
0: Enter Stop mode when the CPU enters Deepsleep. The regulator status depends on the
LPDS bit.
1: Enter Standby mode when the CPU enters Deepsleep.
Bit 0 LPDS: Low-power deepsleep.
This bit is set and cleared by software. It works together with the PDDS bit.
0: Voltage regulator on during Stop mode
1: Voltage regulator in low-power mode during Stop mode
60/713
Doc ID16188 Rev 5
RM0041
Power control (PWR)
4.4.2
Power control/status register (PWR_CSR)
Address offset: 0x04
Reset value: 0x0000 0000 (not reset by wakeup from Standby mode)
Additional APB cycles are needed to read this register versus a standard APB read.
31
30
29
28
27
26
25
24
23
22
21
20
19
6
5
4
3
18
17
16
Reserved
15
14
13
12
11
10
9
8
7
EWUP
Reserved
2
1
0
PVDO
SBF
WUF
r
r
r
Reserved
rw
Bits 31:9 Reserved, must be kept at reset value.
Bit 8 EWUP: Enable WKUP pin
This bit is set and cleared by software.
0: WKUP pin is used for general purpose I/O. An event on the WKUP pin does not wakeup
the device from Standby mode.
1: WKUP pin is used for wakeup from Standby mode and forced in input pull down
configuration (rising edge on WKUP pin wakes-up the system from Standby mode).
Note: This bit is reset by a system Reset.
Bits 7:3 Reserved, must be kept at reset value.
Bit 2 PVDO: PVD output
This bit is set and cleared by hardware. It is valid only if PVD is enabled by the PVDE bit.
0: VDD/VDDA is higher than the PVD threshold selected with the PLS[2:0] bits.
1: VDD/VDDA is lower than the PVD threshold selected with the PLS[2:0] bits.
Note: The PVD is stopped by Standby mode. For this reason, this bit is equal to 0 after
Standby or reset until the PVDE bit is set.
Bit 1 SBF: Standby flag
This bit is set by hardware and cleared only by a POR/PDR (power on reset/power down reset)
or by setting the CSBF bit in the Power control register (PWR_CR)
0: Device has not been in Standby mode
1: Device has been in Standby mode
Bit 0 WUF: Wakeup flag
This bit is set by hardware and cleared by hardware, by a system reset or by setting the
CWUF bit in the Power control register (PWR_CR)
0: No wakeup event occurred
1: A wakeup event was received from the WKUP pin or from the RTC alarm
Note: An additional wakeup event is detected if the WKUP pin is enabled (by setting the
EWUP bit) when the WKUP pin level is already high.
Doc ID16188 Rev 5
61/713
62
Power control (PWR)
4.4.3
RM0041
PWR register map
The following table summarizes the PWR registers.
Reserved
0x004
PWR_CSR
0 0 0 0 0 0 0 0 0
Reserved
Reset value
0
Reserved
PVDO
SBF
WUF
Reset value
PLS
[2:0]
PVDE
CSBF
CWUF
PDDS
LPDS
PWR_CR
DBP
0x000
Register
EWUP
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 13. PWR register map and reset values
0 0 0
Refer to Table 1 on page 36 and Table 2 on page 37 for the register boundary addresses.
62/713
Doc ID16188 Rev 5
RM0041
5
Backup registers (BKP)
Backup registers (BKP)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
5.1
BKP introduction
The backup registers are ten 16-bit registers in low and medium density devices and forttwo registers in high-density devices for storing 20 or 84 bytes of user application data.
They are implemented in the backup domain that remains powered on by VBAT when the
VDD power is switched off. They are not reset when the device wakes up from Standby
mode or by a system reset or power reset.
In addition, the BKP control registers are used to manage the Tamper detection feature and
RTC calibration.
After reset, access to the Backup registers and RTC is disabled and the Backup domain
(BKP) is protected against possible parasitic write access. To enable access to the Backup
registers and the RTC, proceed as follows:
5.2
•
enable the power and backup interface clocks by setting the PWREN and BKPEN bits
in the RCC_APB1ENR register
•
set the DBP bit the Power Control Register (PWR_CR) to enable access to the Backup
registers and RTC.
BKP main features
•
20-byte data registers (in low and medium-density devices) or 84-byte data registers (in
high-density devices)
•
Status/control register for managing tamper detection with interrupt capability
•
Calibration register for storing the RTC calibration value
•
Possibility to output the RTC Calibration Clock, RTC Alarm pulse or Second pulse on
TAMPER pin PC13 (when this pin is not used for tamper detection)
Doc ID16188 Rev 5
63/713
68
Backup registers (BKP)
RM0041
5.3
BKP functional description
5.3.1
Tamper detection
The TAMPER pin generates a Tamper detection event when the pin changes from 0 to 1 or
from 1 to 0 depending on the TPAL bit in the Backup control register (BKP_CR). A tamper
detection event resets all data backup registers.
However to avoid losing Tamper events, the signal used for edge detection is logically
ANDed with the Tamper enable in order to detect a Tamper event in case it occurs before
the TAMPER pin is enabled.
•
When TPAL=0: If the TAMPER pin is already high before it is enabled (by setting TPE
bit), an extra Tamper event is detected as soon as the TAMPER pin is enabled (while
there was no rising edge on the TAMPER pin after TPE was set)
•
When TPAL=1: If the TAMPER pin is already low before it is enabled (by setting the
TPE bit), an extra Tamper event is detected as soon as the TAMPER pin is enabled
(while there was no falling edge on the TAMPER pin after TPE was set)
By setting the TPIE bit in the BKP_CSR register, an interrupt is generated when a Tamper
detection event occurs.
After a Tamper event has been detected and cleared, the TAMPER pin should be disabled
and then re-enabled with TPE before writing to the backup data registers (BKP_DRx) again.
This prevents software from writing to the backup data registers (BKP_DRx), while the
TAMPER pin value still indicates a Tamper detection. This is equivalent to a level detection
on the TAMPER pin.
Note:
Tamper detection is still active when VDD power is switched off. To avoid unwanted resetting
of the data backup registers, the TAMPER pin should be externally tied to the correct level.
5.3.2
RTC calibration
For measurement purposes, the RTC clock with a frequency divided by 64 can be output on
the TAMPER pin. This is enabled by setting the CCO bit in the RTC clock calibration register
(BKP_RTCCR).
The clock can be slowed down by up to 121 ppm by configuring CAL[6:0] bits.
For more details about RTC calibration and how to use it to improve timekeeping accuracy,
refer to AN2604 "STM32F101xx and STM32F103xx RTC calibration”.
64/713
Doc ID16188 Rev 5
RM0041
Backup registers (BKP)
5.4
BKP registers
Refer to Section 1.1 on page 32 for a list of abbreviations used in register descriptions.
The peripheral registers can be accessed by half-words (16-bit) or words (32-bit).
5.4.1
Backup data register x (BKP_DRx) (x = 1 ..42)
Address offset: 0x04 to 0x28, 0x40 to 0xBC
Reset value: 0x0000 0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
D[15:0]
Bits 15:0 D[15:0] Backup data
These bits can be written with user data.
Note: The BKP_DRx registers are not reset by a System reset or Power reset or when the
device wakes up from Standby mode.
They are reset by a Backup Domain reset or by a TAMPER pin event (if the TAMPER
pin function is activated).
5.4.2
RTC clock calibration register (BKP_RTCCR)
Address offset: 0x2C
Reset value: 0x0000 0000
15
14
13
12
Reserved
11
10
9
8
7
ASOS
ASOE
CCO
rw
rw
rw
6
5
4
rw
rw
rw
3
2
1
0
rw
rw
rw
CAL[6:0]
rw
Bits 15:10 Reserved, must be kept at reset value.
Bit 9 ASOS: Alarm or second output selection
When the ASOE bit is set, the ASOS bit can be used to select whether the signal output on
the TAMPER pin is the RTC Second pulse signal or the Alarm pulse signal:
0: RTC Alarm pulse output selected
1: RTC Second pulse output selected
Note: This bit is reset only by a Backup domain reset.
Doc ID16188 Rev 5
65/713
68
Backup registers (BKP)
RM0041
Bit 8 ASOE: Alarm or second output enable
Setting this bit outputs either the RTC Alarm pulse signal or the Second pulse signal on the
TAMPER pin depending on the ASOS bit.
The output pulse duration is one RTC clock period. The TAMPER pin must not be enabled
while the ASOE bit is set.
Note: This bit is reset only by a Backup domain reset.
Bit 7 CCO: Calibration clock output
0: No effect
1: Setting this bit outputs the RTC clock with a frequency divided by 64 on the TAMPER pin.
The TAMPER pin must not be enabled while the CCO bit is set in order to avoid unwanted
Tamper detection.
Note: This bit is reset when the VDD supply is powered off.
Bit 6:0 CAL[6:0]: Calibration value
This value indicates the number of clock pulses that will be ignored every 2^20 clock pulses.
This allows the calibration of the RTC, slowing down the clock by steps of 1000000/2^20
PPM.
The clock of the RTC can be slowed down from 0 to 121PPM.
5.4.3
Backup control register (BKP_CR)
Address offset: 0x30
Reset value: 0x0000 0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
Reserved
1
0
TPAL
TPE
rw
rw
Bits 15:2 Reserved, must be kept at reset value.
Bit 1 TPAL: TAMPER pin active level
0: A high level on the TAMPER pin resets all data backup registers (if TPE bit is set).
1: A low level on the TAMPER pin resets all data backup registers (if TPE bit is set).
Bit 0 TPE: TAMPER pin enable
0: The TAMPER pin is free for general purpose I/O
1: Tamper alternate I/O function is activated.
Note:
Setting the TPAL and TPE bits at the same time is always safe, however resetting both at
the same time can generate a spurious Tamper event. For this reason it is recommended to
change the TPAL bit only when the TPE bit is reset.
5.4.4
Backup control/status register (BKP_CSR)
Address offset: 0x34
Reset value: 0x0000 0000
15
14
13
12
Reserved
66/713
11
10
9
8
TIF
TEF
r
r
7
Doc ID16188 Rev 5
6
5
Reserved
4
3
2
1
0
TPIE
CTI
CTE
rw
w
w
RM0041
Backup registers (BKP)
Bits 15:10 Reserved, must be kept at reset value.
Bit 9 TIF: Tamper interrupt flag
This bit is set by hardware when a Tamper event is detected and the TPIE bit is set. It is
cleared by writing 1 to the CTI bit (also clears the interrupt). It is also cleared if the TPIE bit is
reset.
0: No Tamper interrupt
1: A Tamper interrupt occurred
Note: This bit is reset only by a system reset and wakeup from Standby mode.
Bit 8 TEF: Tamper event flag
This bit is set by hardware when a Tamper event is detected. It is cleared by writing 1 to the
CTE bit.
0: No Tamper event
1: A Tamper event occurred
Note: A Tamper event resets all the BKP_DRx registers. They are held in reset as long as the
TEF bit is set. If a write to the BKP_DRx registers is performed while this bit is set, the
value will not be stored.
Bits 7:3 Reserved, must be kept at reset value.
Bit 2 TPIE: TAMPER pin interrupt enable
0: Tamper interrupt disabled
1: Tamper interrupt enabled (the TPE bit must also be set in the BKP_CR register
Note: A Tamper interrupt does not wake up the core from low-power modes.
This bit is reset only by a system reset and wakeup from Standby mode.
Bit 1 CTI: Clear tamper interrupt
This bit is write only, and is always read as 0.
0: No effect
1: Clear the Tamper interrupt and the TIF Tamper interrupt flag.
Bit 0 CTE: Clear tamper event
This bit is write only, and is always read as 0.
0: No effect
1: Reset the TEF Tamper event flag (and the Tamper detector)
5.4.5
BKP register map
BKP registers are mapped as 16-bit addressable registers as described in the table below:
Offset
Register
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 14. BKP register map and reset values
Reserved
0x00
0x04
BKP_DR1
Reserved
D[15:0]
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
Doc ID16188 Rev 5
67/713
68
Backup registers (BKP)
RM0041
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x10
BKP_DR4
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x14
BKP_DR5
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x18
BKP_DR6
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x1C
BKP_DR7
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x20
BKP_DR8
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x24
BKP_DR9
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x28
BKP_DR10
D[15:0]
Reserved
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0x2
BKP_RTCCR
ASOS
ASOE
Reset value
Reserved
0 0 0 0 0 0 0 0 0 0
Reset value
0x30
CAL[6:0]
BKP_CR
Reserved
0 0
0 0
Reset value
Reserved
TPIE
Reserved
TIF
BKP_CSR
TEF
Reset value
0x34
0 0 0
Refer to Table 1 on page 36 and Table 2 on page 37 for the register boundary addresses.
68/713
TPE
BKP_DR3
TPAL
0x0C
CTI
BKP_DR2
Doc ID16188 Rev 5
CTE
0x08
Register
CCO
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 14. BKP register map and reset values (continued)
RM0041
6
Reset and clock control (RCC)
Reset and clock control (RCC)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to all STM32F100xx devices, unless otherwise specified.
6.1
Reset
There are three types of reset, defined as system Reset, power Reset and backup domain
Reset.
6.1.1
System reset
A system reset sets all registers to their reset values except the reset flags in the clock
controller CSR register and the registers in the Backup domain (see Figure 4).
A system reset is generated when one of the following events occurs:
1.
A low level on the NRST pin (external reset)
2.
Window watchdog end of count condition (WWDG reset)
3.
Independent watchdog end of count condition (IWDG reset)
4.
A software reset (SW reset) (see Software reset)
5.
Low-power management reset (see Low-power management reset)
The reset source can be identified by checking the reset flags in the Control/Status register,
RCC_CSR (see Section 6.3.10: Control/status register (RCC_CSR)).
Software reset
The SYSRESETREQ bit in Cortex®-M3 Application Interrupt and Reset Control Register
must be set to force a software reset on the device. Refer to the Cortex®-M3 technical
reference manual for more details.
Low-power management reset
There are two ways to generate a low-power management reset:
1.
Reset generated when entering Standby mode:
This type of reset is enabled by resetting nRST_STDBY bit in User Option Bytes. In this
case, whenever a Standby mode entry sequence is successfully executed, the device
is reset instead of entering Standby mode.
2.
Reset when entering Stop mode:
This type of reset is enabled by resetting NRST_STOP bit in User Option Bytes. In this
case, whenever a Stop mode entry sequence is successfully executed, the device is
reset instead of entering Stop mode.
Doc ID16188 Rev 5
69/713
99
Reset and clock control (RCC)
RM0041
For further information on the User Option Bytes, refer to the STM32F100xx Flash
programming manual.
6.1.2
Power reset
A power reset is generated when one of the following events occurs:
1.
Power-on/power-down reset (POR/PDR reset)
2.
When exiting Standby mode
A power reset sets all registers to their reset values except the Backup domain (see
Figure 4)
These sources act on the NRST pin and it is always kept low during the delay phase. The
RESET service routine vector is fixed at address 0x0000_0004 in the memory map. For more
details, refer to Table 51: External interrupt/event controller register map and reset values
on page 141.
The system reset signal provided to the device is output on the NRST pin. The pulse
generator guarantees a minimum reset pulse duration of 20 µs for each internal reset
source. In case of an external reset, the reset pulse is generated while the NRST pin is
asserted low.
Figure 7. Simplified diagram of the reset circuit
9''9''$
538
([WHUQDO
UHVHW
)LOWHU
6\VWHPUHVHW
1567
3XOVH
JHQHUDWRU
PLQ—V
::'*UHVHW
,:'*UHVHW
3RZHUUHVHW
6RIWZDUHUHVHW
/RZSRZHUPDQDJHPHQWUHVHW
DLF
6.1.3
Backup domain reset
The backup domain has two specific resets that affect only the backup domain (see
Figure 4).
A backup domain reset is generated when one of the following events occurs:
70/713
1.
Software reset, triggered by setting the BDRST bit in the Backup domain control
register (RCC_BDCR).
2.
VDD or VBAT power on, if both supplies have previously been powered off.
Doc ID16188 Rev 5
RM0041
6.2
Reset and clock control (RCC)
Clocks
Three different clock sources can be used to drive the system clock (SYSCLK):
•
HSI oscillator clock
•
HSE oscillator clock
•
PLL clock
The devices have the following two secondary clock sources:
•
40 kHz low speed internal RC (LSI RC) which drives the independent watchdog and
optionally the RTC used for Auto-wakeup from Stop/Standby mode.
•
32.768 kHz low speed external crystal (LSE crystal) which optionally drives the realtime clock (RTCCLK)
Each clock source can be switched on or off independently when it is not used, to optimize
power consumption.
Figure 8. STM32F100xx clock tree (low and medium-density devices)
&,)4&#,+
TO&LASHPROGRAMMINGINTERFACE
-(Z
(3)2#
(3)
(#,+
TO!("BUSCORE
MEMORYAND$-!
-(ZMAX
0,,32#
37
0,,-5,
(3)
X
XXX
0,,
393#,+
!("
0RESCALER
-(Z
MAX
0,,#,+
#LOCK
%NABLE
!0"
0RESCALER
(3%
/3#?).
!0"
0RESCALER
(3%/3#
/3#?/54
TO24#
,3%
24##,+
!$#
0RESCALER
0#,+
-(ZMAX
0ERIPHERAL#LOCK
%NABLE
4)-TIMERS
)F!0"PRESCALERX
ELSEX
,3%/3#
K(Z
TO4)-AND
4)-X#,+
0ERIPHERAL#LOCK
%NABLE
/3#?).
0#,+
TO!0"
PERIPHERALS
0ERIPHERAL#LOCK
%NABLE
02%$)6
-(Z
-(ZMAX
4)-
)F!0"PRESCALERX
ELSEX
#33
/3#?/54
TO#ORTEX3YSTEMTIMER
&#,+#ORTEX
FREERUNNINGCLOCK
PERIPHERALSTO!0"
TO4)-4)-
4)-AND4)-
4)-X#,+
0ERIPHERAL#LOCK
%NABLE
TO!$#
!$##,+-(ZMAX
24#3%,;=
,3)2#
K(Z
TOINDEPENDENTWATCHDOG)7$'
,3)
)7$'#,+
-AIN
CLOC KOUT PUT
-#/
0,,#,+
,EGEND
(3%(IGHSPEEDEXTERNALCLOCKSIGNAL
(3)
(3) (IGHSPEEDINTERNALCLOCKSIGNAL
(3%
,3),OWSPEEDINTERNALCLOCKSIGNAL
393#,+
,3%,OWSPEEDEXTERNALCLOCKSIGNAL
-#/
AI
1. For full details about the internal and external clock source characteristics, refer to the “Electrical
characteristics” section in the device datasheet.
Doc ID16188 Rev 5
71/713
99
Reset and clock control (RCC)
RM0041
Figure 9. STM32F100xx clock tree (high-density devices)
&,)4&#,+
TO&LASHPROGRAMMINGINTERFACE
-(Z
(3)2#
(3)
0ERIPHERALCLOCK
&3-#,+
(#,+
TO!("BUSCORE
MEMORYAND$-!
-(ZMAX
0,,32#
37
0,,-5,
(3)
X
XXX
0,,
393#,+
!("
0RESCALER
-(Z
MAX
0,,#,+
#LOCK
%NABLE
!0"
0RESCALER
(3%
/3#?).
/3#?/54
0#,+
TO!0"
PERIPHERALS
0ERIPHERAL#LOCK
!0"
0RESCALER
(3%/3#
TO24#
,3%
24##,+
!$#
0RESCALER
0#,+
-(ZMAX
0ERIPHERAL#LOCK
%NABLE
4)-TIMERS
)F!0"PRESCALERX
ELSEX
,3%/3#
K(Z
TO4)-
4)-X#,+
0ERIPHERAL#LOCK
%NABLE
/3#?).
-(ZMAX
%NABLE
02%$)6
-(Z
TO#ORTEX3YSTEMTIMER
&#,+#ORTEX
FREERUNNINGCLOCK
4)-
)F!0"PRESCALERX
ELSEX
#33
/3#?/54
TO&3-#
%NABLE
PERIPHERALSTO!0"
TO4)-4)-
4)-AND4)-
4)-X#,+
0ERIPHERAL#LOCK
%NABLE
TO!$#
!$##,+-(ZMAX
24#3%,;=
,3)2#
K(Z
TOINDEPENDENTWATCHDOG)7$'
,3)
)7$'#,+
-AIN
CLOC KOUT PUT
-#/
0,,#,+
,EGEND
(3%(IGHSPEEDEXTERNALCLOCKSIGNAL
(3)
(3) (IGHSPEEDINTERNALCLOCKSIGNAL
(3%
,3),OWSPEEDINTERNALCLOCKSIGNAL
393#,+
,3%,OWSPEEDEXTERNALCLOCKSIGNAL
-#/
AI
Several prescalers allow the configuration of the AHB frequency, the high speed APB
(APB2) and the low speed APB (APB1) domains. The maximum frequency of the AHB,
APB1 and APB2 domains is 24 MHz.
The RCC feeds the Cortex System Timer (SysTick) external clock with the AHB clock
(HCLK) divided by 8. The SysTick can work either with this clock or with the Cortex clock
(HCLK), configurable in the SysTick Control and Status Register. ADC1 is clocked by the
clock of the High Speed domain (APB2) divided by 2, 4, 6 or 8.
The Flash memory programming interface clock (FLITFCLK) is always the HSI clock.
The timer clock frequencies are automatically fixed by hardware. There are two cases:
1.
if the APB prescaler is 1, the timer clock frequencies are set to the same frequency as
that of the APB domain to which the timers are connected.
2.
otherwise, they are set to twice (×2) the frequency of the APB domain to which the
timers are connected.
FCLK acts as Cortex®-M3 free running clock. For more details refer to the ARM Cortex®-M3
Technical Reference
72/713
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
Manual.http://infocenter.arm.com/help/topic/com.arm.doc.ddi0337e/DDI0337E_cortex_m3_r1p1
_trm.pdf
6.2.1
HSE clock
The high speed external clock signal (HSE) can be generated from two possible clock
sources:
•
HSE external crystal/ceramic resonator
•
HSE user external clock
The resonator and the load capacitors have to be placed as close as possible to the
oscillator pins in order to minimize output distortion and startup stabilization time. The
loading capacitance values must be adjusted according to the selected oscillator.
Figure 10. HSE/ LSE clock sources
Clock source
Hardware configuration
OSC_OUT
External clock
(HiZ)
External
source
OSC_IN OSC_OUT
Crystal/Ceramic
resonators
CL1
Load
capacitors
CL2
External source (HSE bypass)
In this mode, an external clock source must be provided. It can have a frequency of up to
24 MHz. This mode is selected by setting the HSEBYP and HSEON bits in the Clock control
register (RCC_CR). The external clock signal (square, sinus or triangle) with ~50% duty
cycle has to drive the OSC_IN pin while the OSC_OUT pin should be left hi-Z. See
Figure 10.
Doc ID16188 Rev 5
73/713
99
Reset and clock control (RCC)
RM0041
External crystal/ceramic resonator (HSE crystal)
The 4 to 24 MHz external oscillator has the advantage of producing a very accurate rate on
the main clock.
The associated hardware configuration is shown in Figure 10. Refer to the electrical
characteristics section of the datasheet for more details.
The HSERDY flag in the Clock control register (RCC_CR) indicates if the high-speed
external oscillator is stable or not. At startup, the clock is not released until this bit is set by
hardware. An interrupt can be generated if enabled in the Clock interrupt register
(RCC_CIR).
The HSE Crystal can be switched on and off using the HSEON bit in the Clock control
register (RCC_CR).
6.2.2
HSI clock
The HSI clock signal is generated from an internal 8 MHz RC Oscillator and can be used
directly as a system clock or divided by 2 to be used as PLL input.
The HSI RC oscillator has the advantage of providing a clock source at low cost (no external
components). It also has a faster startup time than the HSE crystal oscillator however, even
with calibration the frequency is less accurate than an external crystal oscillator or ceramic
resonator.
Calibration
RC oscillator frequencies can vary from one chip to another due to manufacturing process
variations, this is why each device is factory calibrated by ST for 1% accuracy at TA=25°C.
After reset, the factory calibration value is loaded in the HSICAL[7:0] bits in the Clock control
register (RCC_CR).
If the application is subject to voltage or temperature variations this may affect the RC
oscillator speed. The HSI frequency can be trimmed in the application using the
HSITRIM[4:0] bits in the Clock control register (RCC_CR).
The HSIRDY flag in the Clock control register (RCC_CR) indicates if the HSI RC is stable or
not. At startup, the HSI RC output clock is not released until this bit is set by hardware.
The HSI RC can be switched on and off using the HSION bit in the Clock control register
(RCC_CR).
The HSI signal can also be used as a backup source (Auxiliary clock) if the HSE crystal
oscillator fails. Refer to Section 6.2.7: Clock security system (CSS) on page 76.
6.2.3
PLL
The internal PLL can be used to multiply the HSI RC output or HSE oscillator divided by
1..16 output clock frequency. Refer to Figure 8 and Clock control register (RCC_CR).
The PLL configuration (selection of HSI oscillator divided by 2 or HSE oscillator for PLL
input clock, and multiplication factor) must be done before enabling the PLL. Once the PLL
enabled, these parameters cannot be changed.
Note:
74/713
The PLL output frequency must be in the range of 16-24 MHz.
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
An interrupt can be generated when the PLL is ready if enabled in the Clock interrupt
register (RCC_CIR).
6.2.4
LSE clock
The LSE crystal is a 32.768 kHz Low Speed External crystal or ceramic resonator. It has the
advantage providing a low-power but highly accurate clock source to the real-time clock
peripheral (RTC) for clock/calendar or other timing functions.
The LSE crystal is switched on and off using the LSEON bit in Backup domain control
register (RCC_BDCR).
The LSERDY flag in the Backup domain control register (RCC_BDCR) indicates if the LSE
crystal is stable or not. At startup, the LSE crystal output clock signal is not released until
this bit is set by hardware. An interrupt can be generated if enabled in the Clock interrupt
register (RCC_CIR).
External source (LSE bypass)
In this mode, an external clock source must be provided. It must have a frequency of
32.768 kHz. This mode is selected by setting the LSEBYP and LSEON bits in the Backup
domain control register (RCC_BDCR). The external clock signal (square, sinus or triangle)
with ~50% duty cycle has to drive the OSC32_IN pin while the OSC32_OUT pin should be
left Hi-Z. See Figure 10.
6.2.5
LSI clock
The LSI RC acts as an low-power clock source that can be kept running in Stop and
Standby mode for the independent watchdog (IWDG) and Auto-wakeup unit (AWU). The
clock frequency is around 40 kHz. For more details, refer to the electrical characteristics
section of the datasheets.
The LSI RC can be switched on and off using the LSION bit in the Control/status register
(RCC_CSR).
The LSIRDY flag in the Control/status register (RCC_CSR) indicates if the low-speed
internal oscillator is stable or not. At startup, the clock is not released until this bit is set by
hardware. An interrupt can be generated if enabled in the Clock interrupt register
(RCC_CIR).
LSI calibration
Note:
LSI calibration is only available on high-density value line devices.
The frequency dispersion of the Low Speed Internal RC (LSI) oscillator can be calibrated to
have accurate RTC time base and/or IWDG timeout (when LSI is used as clock source for
these peripherals) with an acceptable accuracy.
This calibration is performed by measuring the LSI clock frequency with respect to TIM5
input clock (TIM5CLK). According to this measurement done at the precision of the HSE
oscillator, the software can adjust the programmable 20-bit prescaler of the RTC to get an
accurate time base or can compute accurate IWDG timeout.
Use the following procedure to calibrate the LSI:
Doc ID16188 Rev 5
75/713
99
Reset and clock control (RCC)
6.2.6
RM0041
1.
Enable TIM5 timer and configure channel4 in input capture mode
2.
Set the TIM5CH4_IREMAP bit in the AFIO_MAPR register to connect the LSI clock
internally to TIM5 channel4 input capture for calibration purposes.
3.
Measure the frequency of LSI clock using the TIM5 Capture/compare 4 event or
interrupt.
4.
Use the measured LSI frequency to update the 20-bit prescaler of the RTC depending
on the desired time base and/or to compute the IWDG timeout.
System clock (SYSCLK) selection
After a system reset, the HSI oscillator is selected as system clock. When a clock source is
used directly or through the PLL as system clock, it is not possible to stop it.
A switch from one clock source to another occurs only if the target clock source is ready
(clock stable after startup delay or PLL locked). If a clock source which is not yet ready is
selected, the switch will occur when the clock source will be ready. Status bits in the Clock
control register (RCC_CR) indicate which clock(s) is (are) ready and which clock is currently
used as system clock.
6.2.7
Clock security system (CSS)
Clock Security System can be activated by software. In this case, the clock detector is
enabled after the HSE oscillator startup delay, and disabled when this oscillator is stopped.
If a failure is detected on the HSE clock, the HSE oscillator is automatically disabled, a clock
failure event is sent to the break input of the advanced-control timers (TIM1) and an
interrupt is generated to inform the software about the failure (Clock Security System
Interrupt CSSI), allowing the MCU to perform rescue operations. The CSSI is linked to the
Cortex®-M3 NMI (Non-Maskable Interrupt) exception vector.
Note:
Once the CSS is enabled and if the HSE clock fails, the CSS interrupt occurs and an NMI is
automatically generated. The NMI will be executed indefinitely unless the CSS interrupt
pending bit is cleared. As a consequence, in the NMI ISR user must clear the CSS interrupt
by setting the CSSC bit in the Clock interrupt register (RCC_CIR).
If the HSE oscillator is used directly or indirectly as the system clock (indirectly means: it is
used as PLL input clock, and the PLL clock is used as system clock), a detected failure
causes a switch of the system clock to the HSI oscillator and the disabling of the HSE
oscillator. If the HSE clock (divided or not) is the clock entry of the PLL used as system clock
when the failure occurs, the PLL is disabled too.
6.2.8
RTC clock
The RTCCLK clock source can be either the HSE/128, LSE or LSI clocks. This is selected
by programming the RTCSEL[1:0] bits in the Backup domain control register (RCC_BDCR).
This selection cannot be modified without resetting the Backup domain.
76/713
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
The LSE clock is in the Backup domain, whereas the HSE and LSI clocks are not.
Consequently:
•
If LSE is selected as RTC clock:
–
•
If LSI is selected as Auto-Wakeup unit (AWU) clock:
–
•
The RTC continues to work even if the VDD supply is switched off, provided the
VBAT supply is maintained.
The AWU state is not guaranteed if the VDD supply is powered off. Refer to
Section 6.2.5: LSI clock on page 75 for more details on LSI calibration.
If the HSE clock divided by 128 is used as the RTC clock:
–
The RTC state is not guaranteed if the VDD supply is powered off or if the internal
voltage regulator is powered off (removing power from the 1.8 V domain).
–
The DPB bit (Disable backup domain write protection) in the Power controller
register must be set to 1 (refer to Section 4.4.1: Power control register
(PWR_CR)).
When the RTC clock is LSE, the RTC remains clocked and functional under system reset.
6.2.9
Watchdog clock
If the Independent watchdog (IWDG) is started by either hardware option or software
access, the LSI oscillator is forced ON and cannot be disabled. After the LSI oscillator
temporization, the clock is provided to the IWDG.
6.2.10
Clock-out capability
The microcontroller clock output (MCO) capability allows the clock to be output onto the
external MCO pin. The configuration registers of the corresponding GPIO port must be
programmed in alternate function mode. One of 4 clock signals can be selected as the MCO
clock.
•
SYSCLK
•
HSI
•
HSE
•
PLL clock divided by 2
The selection is controlled by the MCO[2:0] bits of the Clock configuration register
(RCC_CFGR).
Doc ID16188 Rev 5
77/713
99
Reset and clock control (RCC)
6.3
RM0041
RCC registers
Refer to Section 1.1 on page 32 for a list of abbreviations used in register descriptions.
6.3.1
Clock control register (RCC_CR)
Address offset: 0x00
Reset value: 0x0000 XX83 where X is undefined.
Access: no wait state, word, half-word and byte access
31
30
29
28
27
26
Reserved
15
14
13
12
11
10
25
24
PLL
RDY
PLLON
r
rw
9
8
23
22
r
r
Bits 31:26
r
r
20
Reserved
7
6
HSICAL[7:0]
r
21
5
4
19
18
17
16
CSS
ON
HSE
BYP
HSE
RDY
HSE
ON
rw
rw
r
rw
3
2
1
0
HSION
Res.
HSI
RDY
r
rw
HSITRIM[4:0]
r
r
r
rw
rw
rw
rw
rw
Reserved, always read as 0.
Bit 25 PLLRDY: PLL clock ready flag
Set by hardware to indicate that the PLL is locked.
0: PLL unlocked
1: PLL locked
Bit 24 PLLON: PLL enable
Set and cleared by software to enable PLL.
Cleared by hardware when entering Stop or Standby mode. This bit can not be reset if the
PLL clock is used as system clock or is selected to become the system clock.
0: PLL OFF
1: PLL ON
Bits 23:20
Reserved, always read as 0.
Bit 19 CSSON: Clock security system enable
Set and cleared by software to enable the clock security system. When CSSON is set, the
clock detector is enabled by hardware when the HSE oscillator is ready, and disabled by
hardware if an HSE clock failure is detected.
0: Clock detector OFF
1: Clock detector ON (Clock detector ON if the HSE oscillator is ready , OFF if not).
Bit 18 HSEBYP: External high-speed clock bypass
Set and cleared by software to bypass the oscillator with an external clock. The external
clock must be enabled with the HSEON bit set, to be used by the device. The HSEBYP bit
can be written only if the HSE oscillator is disabled.
0: HSE oscillator not bypassed
1: HSE oscillator oscillator bypassed with external clock
Bit 17 HSERDY: External high-speed clock ready flag
Set by hardware to indicate that the HSE oscillator is stable. This bit needs 6 cycles of the
HSE oscillator clock to go to zero after HSEON is reset.
0: HSE oscillator not ready
1: HSE oscillator ready
78/713
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
Bit 16 HSEON: External high-speed clock enable
Set and cleared by software.
Cleared by hardware to stop the HSE oscillator when entering in Stop or Standby mode. This
bit cannot be reset if the HSE oscillator is used directly or indirectly as the system clock.
0: HSE oscillator OFF
1: HSE oscillator ON
Bits 15:8 HSICAL[7:0]: Internal high-speed clock calibration
These bits are initialized automatically at startup.
Bits 7:3 HSITRIM[4:0]: Internal high-speed clock trimming
These bits provide an additional user-programmable trimming value that is added to the
HSICAL[7:0] bits. It can be programmed to adjust to variations in voltage and temperature
that influence the frequency of the internal HSI RC.
The default value is 16, which, when added to the HSICAL value, should trim the HSI to 8
MHz ± 1%. The trimming step (Fhsitrim) is around 40 kHz between two consecutive HSICAL
steps.
Bit 2
Reserved, always read as 0.
Bit 1 HSIRDY: Internal high-speed clock ready flag
Set by hardware to indicate that internal 8 MHz RC oscillator is stable. After the HSION bit is
cleared, HSIRDY goes low after 6 internal 8 MHz RC oscillator clock cycles.
0: internal 8 MHz RC oscillator not ready
1: internal 8 MHz RC oscillator ready
Bit 0 HSION: Internal high-speed clock enable
Set and cleared by software.
Set by hardware to force the internal 8 MHz RC oscillator ON when leaving Stop or Standby
mode or in case of failure of the HSE oscillator used directly or indirectly as system clock.
This bit cannot be reset if the internal 8 MHz RC is used directly or indirectly as system clock
or is selected to become the system clock.
0: internal 8 MHz RC oscillator OFF
1: internal 8 MHz RC oscillator ON
Doc ID16188 Rev 5
79/713
99
Reset and clock control (RCC)
6.3.2
RM0041
Clock configuration register (RCC_CFGR)
Address offset: 0x04
Reset value: 0x0000 0000
Access: 0 ≤ wait state ≤ 2, word, half-word and byte access
1 or 2 wait states inserted only if the access occurs during clock source switch.
31
30
29
28
27
26
25
24
23
22
21
MCO[2:0]
14
13
rw
rw
12
11
10
PPRE2[2:0]
rw
Bits 31:27
18
Reserved
rw
15
19
PLLMUL[3:0]
Reserved
ADC PRE[1:0]
20
rw
rw
rw
9
8
7
6
PPRE1[2:0]
rw
rw
rw
rw
rw
16
PLL
SRC
rw
rw
rw
rw
rw
rw
5
4
3
2
1
0
HPRE[3:0]
rw
17
PLL
XTPRE
rw
SWS[1:0]
rw
r
r
SW[1:0]
rw
rw
Reserved, always read as 0.
Bits 26:24 MCO: Microcontroller clock output
Set and cleared by software.
0xx: No clock
100: System clock (SYSCLK) selected
101: HSI clock selected
110: HSE clock selected
111: PLL clock divided by 2 selected
Note: This clock output may have some truncated cycles at startup or during MCO clock
source switching.
Bits 23:22
Reserved.
Bits 21:18 PLLMUL: PLL multiplication factor
These bits are written by software to define the PLL multiplication factor. These bits can be
written only when PLL is disabled.
Caution: The PLL output frequency must be in the 16-24 MHz range.
0000: PLL input clock x 2
0001: PLL input clock x 3
0010: PLL input clock x 4
0011: PLL input clock x 5
0100: PLL input clock x 6
0101: PLL input clock x 7
0110: PLL input clock x 8
0111: PLL input clock x 9
1000: PLL input clock x 10
1001: PLL input clock x 11
1010: PLL input clock x 12
1011: PLL input clock x 13
1100: PLL input clock x 14
1101: PLL input clock x 15
1110: PLL input clock x 16
1111: PLL input clock x 16
80/713
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
Bit 17 PLLXTPRE: LSB of division factor PREDIV1
Set and cleared by software to select the least significant bit of the PREDIV1 division factor.
It is the same bit as bit 0 in the RCC_CFGR2 register, so modifying bit 0 in the
RCC_CFGR2 register changes this bit accordingly.
If bits[3:1] in the RCC_CFGR2 register are not set, the PLLXTPRE bit controls if PREDIV1
divides its input clock by 2 (PLLXTPRE=1) or not (PLLXTPRE=0).
This bit can be written only when the PLL is disabled.
Bit 16 PLLSRC: PLL entry clock source
Set and cleared by software to select PLL clock source. This bit can be written only when
PLL is disabled.
0: HSI oscillator clock / 2 selected as PLL input clock
1: Clock from PREDIV1 selected as the PLL input clock
Bits 15:14 ADCPRE: ADC prescaler
Set and cleared by software to select the frequency of the clock to ADC1.
00: PLCK2 divided by 2
01: PLCK2 divided by 4
10: PLCK2 divided by 6
11: PLCK2 divided by 8
Bits 13:11 PPRE2: APB high-speed prescaler (APB2)
Set and cleared by software to control the division factor of the APB high-speed clock
(PCLK2).
0xx: HCLK not divided
100: HCLK divided by 2
101: HCLK divided by 4
110: HCLK divided by 8
111: HCLK divided by 16
Bits 10:8 PPRE1: APB low-speed prescaler (APB1)
Set and cleared by software to control the division factor of the APB low-speed clock
(PCLK1).
Warning: the software has to set correctly these bits to not exceed 36 MHz on this domain.
0xx: HCLK not divided
100: HCLK divided by 2
101: HCLK divided by 4
110: HCLK divided by 8
111: HCLK divided by 16
Bits 7:4 HPRE: AHB prescaler
Set and cleared by software to control the division factor of the AHB clock.
0xxx: SYSCLK not divided
1000: SYSCLK divided by 2
1001: SYSCLK divided by 4
1010: SYSCLK divided by 8
1011: SYSCLK divided by 16
1100: SYSCLK divided by 64
1101: SYSCLK divided by 128
1110: SYSCLK divided by 256
1111: SYSCLK divided by 512
Doc ID16188 Rev 5
81/713
99
Reset and clock control (RCC)
RM0041
Bits 3:2 SWS: System clock switch status
Set and cleared by hardware to indicate which clock source is used as system clock.
00: HSI oscillator used as system clock
01: HSE oscillator used as system clock
10: PLL used as system clock
11: not applicable
Bits 1:0 SW: System clock switch
Set and cleared by software to select SYSCLK source.
Set by hardware to force HSI selection when leaving Stop and Standby mode or in case of
failure of the HSE oscillator used directly or indirectly as system clock (if the Clock Security
System is enabled).
00: HSI selected as system clock
01: HSE selected as system clock
10: PLL selected as system clock
11: not allowed
6.3.3
Clock interrupt register (RCC_CIR)
Address offset: 0x08
Reset value: 0x0000 0000
Access: no wait state, word, half-word and byte access
31
30
29
28
27
26
25
24
23
22
21
CSSC
Reserved
Reserved
w
15
14
13
Reserved
Bits 31:24
12
11
10
9
8
PLL
RDYIE
HSE
RDYIE
HSI
RDYIE
LSE
RDYIE
LSI
RDYIE
7
CSSF
rw
rw
rw
rw
rw
r
6
5
Reserved
Reserved, always read as 0.
Bit 23 CSSC: Clock security system interrupt clear
This bit is set by software to clear the CSSF flag.
0: No effect
1: Clear CSSF flag
Bits 22:21
Reserved, always read as 0.
Bit 20 PLLRDYC: PLL ready interrupt clear
This bit is set by software to clear the PLLRDYF flag.
0: No effect
1: PLLRDYF cleared
Bit 19 HSERDYC: HSE ready interrupt clear
This bit is set by software to clear the HSERDYF flag.
0: No effect
1: HSERDYF cleared
82/713
Doc ID16188 Rev 5
20
19
18
17
16
PLL
RDYC
HSE
RDYC
HSI
RDYC
LSE
RDYC
LSI
RDYC
w
w
w
w
w
4
3
2
1
0
PLL
RDYF
HSE
RDYF
HSI
RDYF
LSE
RDYF
LSI
RDYF
r
r
r
r
r
RM0041
Reset and clock control (RCC)
Bit 18 HSIRDYC: HSI ready interrupt clear
This bit is set software to clear the HSIRDYF flag.
0: No effect
1: HSIRDYF cleared
Bit 17 LSERDYC: LSE ready interrupt clear
This bit is set by software to clear the LSERDYF flag.
0: No effect
1: LSERDYF cleared
Bit 16 LSIRDYC: LSI ready interrupt clear
This bit is set by software to clear the LSIRDYF flag.
0: No effect
1: LSIRDYF cleared
Bits 15:13
Reserved, always read as 0.
Bit 12 PLLRDYIE: PLL ready interrupt enable
Set and cleared by software to enable/disable interrupt caused by PLL lock.
0: PLL lock interrupt disabled
1: PLL lock interrupt enabled
Bit 11 HSERDYIE: HSE ready interrupt enable
Set and cleared by software to enable/disable interrupt caused by the HSE oscillator
stabilization.
0: HSE ready interrupt disabled
1: HSE ready interrupt enabled
Bit 10 HSIRDYIE: HSI ready interrupt enable
Set and cleared by software to enable/disable interrupt caused by the internal 8 MHz RC
oscillator stabilization.
0: HSI ready interrupt disabled
1: HSI ready interrupt enabled
Bit 9 LSERDYIE: LSE ready interrupt enable
Set and cleared by software to enable/disable interrupt caused by the external 32 kHz
oscillator stabilization.
0: LSE ready interrupt disabled
1: LSE ready interrupt enabled
Bit 8 LSIRDYIE: LSI ready interrupt enable
Set and cleared by software to enable/disable interrupt caused by internal RC 40 kHz
oscillator stabilization.
0: LSI ready interrupt disabled
1: LSI ready interrupt enabled
Bit 7 CSSF: Clock security system interrupt flag
Set by hardware when a failure is detected in the HSE oscillator.
Cleared by software setting the CSSC bit.
0: No clock security interrupt caused by HSE clock failure
1: Clock security interrupt caused by HSE clock failure
Bits 6:5
Reserved, always read as 0.
Doc ID16188 Rev 5
83/713
99
Reset and clock control (RCC)
RM0041
Bit 4 PLLRDYF: PLL ready interrupt flag
Set by hardware when the PLL locks and PLLRDYDIE is set.
Cleared by software setting the PLLRDYC bit.
0: No clock ready interrupt caused by PLL lock
1: Clock ready interrupt caused by PLL lock
Bit3 HSERDYF: HSE ready interrupt flag
Set by hardware when External High Speed clock becomes stable and HSERDYDIE is set.
Cleared by software setting the HSERDYC bit.
0: No clock ready interrupt caused by the HSE oscillator
1: Clock ready interrupt caused by the HSE oscillator
Bit 2 HSIRDYF: HSI ready interrupt flag
Set by hardware when the Internal High Speed clock becomes stable and HSIRDYDIE is
set.
Cleared by software setting the HSIRDYC bit.
0: No clock ready interrupt caused by the internal 8 MHz RC oscillator
1: Clock ready interrupt caused by the internal 8 MHz RC oscillator
Bit 1 LSERDYF: LSE ready interrupt flag
Set by hardware when the External Low Speed clock becomes stable and LSERDYDIE is
set.
Cleared by software setting the LSERDYC bit.
0: No clock ready interrupt caused by the external 32 kHz oscillator
1: Clock ready interrupt caused by the external 32 kHz oscillator
Bit 0 LSIRDYF: LSI ready interrupt flag
Set by hardware when the internal low speed clock becomes stable and LSIRDYDIE is set.
Cleared by software setting the LSIRDYC bit.
0: No clock ready interrupt caused by the internal RC 40 kHz oscillator
1: Clock ready interrupt caused by the internal RC 40 kHz oscillator
6.3.4
APB2 peripheral reset register (RCC_APB2RSTR)
Address offset: 0x0C
Reset value: 0x00000 0000
Access: no wait state, word, half-word and byte access
31
30
29
28
27
26
25
24
23
22
21
20
19
Reserved
18
17
16
TIM17
RST
TIM16
RST
TIM15
RST
rw
rw
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
USART1
RST
Res.
SPI1
RST
TIM1
RST
Res.
ADC1
RST
IOPG
RST
IOPF
RST
IOPE
RST
IOPD
RST
IOPC
RST
IOPB
RST
IOPA
RST
Res.
Res.
AFIO
RST
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Res.
rw
rw
Bits 31:19
84/713
Reserved, always read as 0.
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
Bit 18 TIM17RST: TIM17 reset
Set and cleared by software.
0: No effect
1: Reset TIM17
Bit 17 TIM16RST: TIM16 reset
Set and cleared by software.
0: No effect
1: Resets TIM16
Bit 16 TIM15RST: TIM15 reset
Set and cleared by software.
0: No effect
1: Resets TIM15
Bit 15
Reserved.
Bit 14 USART1RST: USART1 reset
Set and cleared by software.
0: No effect
1: Reset USART1
Bit 13
Reserved.
Bit 12 SPI1RST: SPI 1 reset
Set and cleared by software.
0: No effect
1: Reset SPI 1
Bit 11 TIM1RST: TIM1 timer reset
Set and cleared by software.
0: No effect
1: Reset TIM1 timer
Bit 10
Reserved.
Bit 9 ADC1RST: ADC 1 interface reset
Set and cleared by software.
0: No effect
1: Reset ADC 1 interface
Bit 8 IOPGRST: IO port G reset
Set and cleared by software.
0: No effect
1: Reset IO port G
Bit 7 IOPFRST: IO port F reset
Set and cleared by software.
0: No effect
1: Reset I/O port F
Bit 6 IOPERST: IO port E reset
Set and cleared by software.
0: No effect
1: Reset IO port E
Doc ID16188 Rev 5
85/713
99
Reset and clock control (RCC)
RM0041
Bit 5 IOPDRST: IO port D reset
Set and cleared by software.
0: No effect
1: Reset I/O port D
Bit 4 IOPCRST: IO port C reset
Set and cleared by software.
0: No effect
1: Reset I/O port C
Bit 3 IOPBRST: IO port B reset
Set and cleared by software.
0: No effect
1: Reset I/O port B
Bit 2 IOPARST: I/O port A reset
Set and cleared by software.
0: No effect
1: Reset I/O port A
Bit 1
Reserved, always read as 0.
Bit 0 AFIORST: Alternate function I/O reset
Set and cleared by software.
0: No effect
1: Reset Alternate Function
6.3.5
APB1 peripheral reset register (RCC_APB1RSTR)
Address offset: 0x10
Reset value: 0x0000 0000
Access: no wait state, word, half-word and byte access
31
30
29
28
27
Res.
CECR
ST
DAC
RST
PWR
RST
BKP
RST
rw
rw
rw
rw
15
14
13
12
11
SPI3
RST
SPI2
RST
rw
rw
Reserved
WWDG
RST
rw
Bit 31
26
25
24
23
Reserved
10
9
Reserved
22
21
20
19
I2C2
RST
I2C1
RST
UART5
RST
UART4
RST
rw
rw
rw
rw
rw
rw
17
USART3 USART2
RST
RST
16
Res.
8
7
6
5
4
3
2
1
0
TIM14
RST
TIM13
RST
TIM12
RST
TIM7
RST
TIM6
RST
TIM5
RST
TIM4
RST
TIM3
RST
TIM2
RST
rw
rw
rw
rw
rw
rw
rw
rw
rw
Reserved, always read as 0.
Bit 30 CECRST: CEC reset
Set and cleared by software.
0: No effect
1: Reset CEC
Bit 29 DACRST: DAC interface reset
Set and cleared by software.
0: No effect
1: Reset DAC interface
86/713
18
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
Bit 28 PWRRST: Power interface reset
Set and cleared by software.
0: No effect
1: Reset power interface
Bit 27 BKPRST: Backup interface reset
Set and cleared by software.
0: No effect
1: Reset backup interface
Bits 26:23
Reserved, always read as 0.
Bit 22 I2C2RST: I2C 2 reset
Set and cleared by software.
0: No effect
1: Reset I2C 2
Bit 21 I2C1RST: I2C 1 reset
Set and cleared by software.
0: No effect
1: Reset I2C 1
Bit 20 UART5RST: UART 5 reset
Set and cleared by software.
0: No effect
1: Reset UART 5
Bit 19 UART4RST: UART 4 reset
Set and cleared by software.
0: No effect
1: Reset UART 4
Bit 18 USART3RST: USART 3 reset
Set and cleared by software.
0: No effect
1: Reset USART 3
Bit 17 USART2RST: USART 2 reset
Set and cleared by software.
0: No effect
1: Reset USART 2
Bit 16
Reserved, always read as 0.
Bit 15 SPI3RST: SPI 3 reset
Set and cleared by software.
0: No effect
1: Reset SPI 3
Bit 14 SPI2RST: SPI 2 reset
Set and cleared by software.
0: No effect
1: Reset SPI 2
Bits 13:12
Reserved, always read as 0.
Doc ID16188 Rev 5
87/713
99
Reset and clock control (RCC)
RM0041
Bit 11 WWDGRST: Window watchdog reset
Set and cleared by software.
0: No effect
1: Reset window watchdog
Bits 10:9
Reserved, always read as 0.
Bit 8 TIM14RST: Timer 14 reset
Set and cleared by software.
0: No effect
1: Reset timer 14
Bit 7 TIM13RST: Timer 13 reset
Set and cleared by software.
0: No effect
1: Reset timer 13
Bit 6 TIM12RST: Timer 12 reset
Set and cleared by software.
0: No effect
1: Reset timer 12
Bit 5 TIM7RST: Timer 7 reset
Set and cleared by software.
0: No effect
1: Reset timer 7
Bit 4 TIM6RST: Timer 6 reset
Set and cleared by software.
0: No effect
1: Reset timer 6
Bit 3 TIM5RST: Timer 5 reset
Set and cleared by software.
0: No effect
1: Reset timer 5
Bit 2 TIM4RST: Timer 4 reset
Set and cleared by software.
0: No effect
1: Reset timer 4
Bit 1 TIM3RST: Timer 3 reset
Set and cleared by software.
0: No effect
1: Reset timer 3
Bit 0 TIM2RST: Timer 2 reset
Set and cleared by software.
0: No effect
1: Reset timer 2
6.3.6
AHB peripheral clock enable register (RCC_AHBENR)
Address offset: 0x14
Reset value: 0x0000 0014
88/713
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
Access: no wait state, word, half-word and byte access
Note:
When the peripheral clock is not active, the peripheral register values may not be readable
by software and the returned value is always 0x0.
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
20
19
7
6
Res.
CRCE
N
18
17
16
5
4
3
2
1
0
Res.
FLITF
EN
Res.
SRAM
EN
DMA2
EN
DMA1
EN
rw
rw
rw
Reserved
Reserved
FSMC
EN
rw
Bits 31:9
rw
rw
Reserved, always read as 0.
Bit 8 FSMCEN: FSMC clock enable
Set and cleared by software.
0: FSMC clock disabled
1: FSMC clock enabled
Bit 7
Reserved, always read as 0.
Bit 6 CRCEN: CRC clock enable
Set and cleared by software.
0: CRC clock disabled
1: CRC clock enabled
Bit 5
Reserved, always read as 0.
Bit 4 FLITFEN: FLITF clock enable
Set and cleared by software to disable/enable FLITF clock during sleep mode.
0: FLITF clock disabled during Sleep mode
1: FLITF clock enabled during Sleep mode
Bit 3
Reserved, always read as 0.
Bit 2 SRAMEN: SRAM interface clock enable
Set and cleared by software to disable/enable SRAM interface clock during Sleep mode.
0: SRAM interface clock disabled during Sleep mode.
1: SRAM interface clock enabled during Sleep mode
Bit 1 DMA2EN: DMA2 clock enable
Set and cleared by software.
0: DMA2 clock disabled
1: DMA2 clock enabled
Bit 0 DMA1EN: DMA1 clock enable
Set and cleared by software.
0: DMA1 clock disabled
1: DMA1 clock enabled
Doc ID16188 Rev 5
89/713
99
Reset and clock control (RCC)
6.3.7
RM0041
APB2 peripheral clock enable register (RCC_APB2ENR)
Address: 0x18
Reset value: 0x0000 0000
Access: word, half-word and byte access
No wait states, except if the access occurs while an access to a peripheral in the APB2
domain is on going. In this case, wait states are inserted until the access to APB2 peripheral
is finished.
Note:
31
When the peripheral clock is not active, the peripheral register values may not be readable
by software and the returned value is always 0x0.
30
29
28
27
26
25
24
23
22
21
20
19
Reserved
15
Res.
14
USAR
T1EN
13
12
11
Res.
SPI1
EN
TIM1
EN
rw
rw
rw
Bits 31:19
TIM17
EN
TIM16
EN
TIM15
EN
rw
rw
rw
1
0
Res.
AFIO
EN
9
8
7
6
5
4
3
2
Res.
IOPG
EN
IOPF
EN
IOPE
EN
IOPD
EN
IOPC
EN
IOPB
EN
IOPA
EN
rw
rw
rw
rw
rw
rw
rw
rw
Reserved, always read as 0.
Bit 16 TIM15EN: TIM15 timer clock enable
Set and cleared by software.
0: TIM15 timer clock disabled
1: TIM15 timer clock enabled
Reserved.
Bit 14 USART1EN: USART1 clock enable
Set and cleared by software.
0: USART1 clock disabled
1: USART1 clock enabled
Reserved.
Bit 12 SPI1EN: SPI 1 clock enable
Set and cleared by software.
0: SPI 1 clock disabled
1: SPI 1 clock enabled
90/713
16
ADC1
EN
Bit 17 TIM16EN: TIM16 timer clock enable
Set and cleared by software.
0: TIM16 timer clock disabled
1: TIM16 timer clock enabled
Bit 13
17
10
Bit 18 TIM17EN: TIM17 Timer clock enable
Set and cleared by software.
0: TIM17 timer clock disabled
1: TIM17 timer clock enabled
Bit 15
18
Doc ID16188 Rev 5
rw
RM0041
Reset and clock control (RCC)
Bit 11 TIM1EN: TIM1 Timer clock enable
Set and cleared by software.
0: TIM1 timer clock disabled
1: TIM1 timer clock enabled
Bit 10
Reserved.
Bit 9 ADC1EN: ADC 1 interface clock enable
Set and cleared by software.
0: ADC 1 interface disabled
1: ADC 1 interface clock enabled
Bit 8 IOPGEN: I/O port G clock enable
Set and cleared by software.
0: I/O port G clock disabled
1: I/O port G clock enabled
Bit 7 IOPFEN: I/O port F clock enable
Set and cleared by software.
0: I/O port F clock disabled
1: I/O port F clock enabled
Bit 6 IOPEEN: I/O port E clock enable
Set and cleared by software.
0: I/O port E clock disabled
1: I/O port E clock enabled
Bit 5 IOPDEN: I/O port D clock enable
Set and cleared by software.
0: I/O port D clock disabled
1: I/O port D clock enabled
Bit 4 IOPCEN: I/O port C clock enable
Set and cleared by software.
0: I/O port C clock disabled
1:I/O port C clock enabled
Bit 3 IOPBEN: I/O port B clock enable
Set and cleared by software.
0: I/O port B clock disabled
1:I/O port B clock enabled
Bit 2 IOPAEN: I/O port A clock enable
Set and cleared by software.
0: I/O port A clock disabled
1:I/O port A clock enabled
Bit 1
Reserved, always read as 0.
Bit 0 AFIOEN: Alternate function I/O clock enable
Set and cleared by software.
0: Alternate Function I/O clock disabled
1:Alternate Function I/O clock enabled
Doc ID16188 Rev 5
91/713
99
Reset and clock control (RCC)
6.3.8
RM0041
APB1 peripheral clock enable register (RCC_APB1ENR)
Address: 0x1C
Reset value: 0x0000 0000
Access: word, half-word and byte access
No wait state, except if the access occurs while an access to a peripheral on APB1 domain
is on going. In this case, wait states are inserted until this access to APB1 peripheral is
finished.
Note:
31
Res.
When the peripheral clock is not active, the peripheral register values may not be readable
by software and the returned value is always 0x0.
30
29
28
27
CECE
N
DAC
EN
PWR
EN
BKP
EN
rw
rw
rw
rw
13
12
15
14
SPI3
EN
SPI2
EN
rw
rw
Reserved
11
WWD
GEN
rw
Bits 31:29
26
25
24
23
Reserved
10
9
Reserved
22
21
I2C2
EN
I2C1
EN
rw
rw
UART5E UART4E
N
N
rw
rw
18
17
16
USART
3EN
USART
2EN
Res.
rw
rw
Res.
8
7
6
5
4
3
2
1
0
TIM13
EN
TIM12
EN
TIM7
EN
TIM6
EN
TIM5
EN
TIM4
EN
TIM3
EN
TIM2
EN
rw
rw
rw
rw
rw
rw
rw
rw
rw
Reserved, always read as 0.
Bit 29 DACEN: DAC interface clock enable
Set and cleared by software.
0: DAC interface clock disabled
1: DAC interface clock enable
Bit 28 PWREN: Power interface clock enable
Set and cleared by software.
0: Power interface clock disabled
1: Power interface clock enable
Bit 27 BKPEN: Backup interface clock enable
Set and cleared by software.
0: Backup interface clock disabled
1: Backup interface clock enabled
Reserved, always read as 0.
Bit 22 I2C2EN: I2C 2 clock enable
Set and cleared by software.
0: I2C 2 clock disabled
1: I2C 2 clock enabled
92/713
19
TIM14
EN
Bit 30 CECEN: CEC clock enable
Set and cleared by software.
0: CEC clock disabled
1: CEC clock enabled
Bits 26:23
20
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
Bit 21 I2C1EN: I2C 1 clock enable
Set and cleared by software.
0: I2C 1 clock disabled
1: I2C 1 clock enabled
Bit 20 UART5EN: UART 5 clock enable
Set and cleared by software.
0: UART 5 clock disabled
1: UART 5 clock enabled
Bit 19 UART4EN: UART 4 clock enable
Set and cleared by software.
0: UART 4 clock disabled
1: UART 4 clock enabled
Bit 18 USART3EN: USART 3 clock enable
Set and cleared by software.
0: USART 3 clock disabled
1: USART 3 clock enabled
Bit 17 USART2EN: USART 2 clock enable
Set and cleared by software.
0: USART 2 clock disabled
1: USART 2 clock enabled
Bits 16
Reserved, always read as 0.
Bit 15 SPI3EN: SPI 3 clock enable
Set and cleared by software.
0: SPI 3 clock disabled
1: SPI 3 clock enabled
Bit 14 SPI2EN: SPI 2 clock enable
Set and cleared by software.
0: SPI 2 clock disabled
1: SPI 2 clock enabled
Bits 13:12
Reserved, always read as 0.
Bit 11 WWDGEN: Window watchdog clock enable
Set and cleared by software.
0: Window watchdog clock disabled
1: Window watchdog clock enabled
Bits 10:9
Reserved, always read as 0.
Bit 8 TIM14EN: Timer 14 clock enable
Set and cleared by software.
0: Timer 14 clock disabled
1: Timer 14 clock enabled
Bit 7 TIM13EN: Timer 13 clock enable
Set and cleared by software.
0: Timer 13 clock disabled
1: Timer 13 clock enabled
Doc ID16188 Rev 5
93/713
99
Reset and clock control (RCC)
RM0041
Bit 6 TIM12EN: Timer 12 clock enable
Set and cleared by software.
0: Timer 12 clock disabled
1: Timer 12 clock enabled
Bit 5 TIM7EN: Timer 7clock enable
Set and cleared by software.
0: Timer 7 clock disabled
1: Timer 7 clock enabled
Bit 4 TIM6EN: Timer 6 clock enable
Set and cleared by software.
0: Timer 6 clock disabled
1: Timer 6 clock enabled
Bit 3 TIM5EN: Timer 5 clock enable
Set and cleared by software.
0: Timer 5 clock disabled
1: Timer 5 clock enabled
Bit 2 TIM4EN: Timer 4 clock enable
Set and cleared by software.
0: Timer 4 clock disabled
1: Timer 4 clock enabled
Bit 1 TIM3EN: Timer 3 clock enable
Set and cleared by software.
0: Timer 3 clock disabled
1: Timer 3 clock enabled
Bit 0 TIM2EN: Timer 2 clock enable
Set and cleared by software.
0: Timer 2 clock disabled
1: Timer 2 clock enabled
94/713
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
6.3.9
Backup domain control register (RCC_BDCR)
Address offset: 0x20
Reset value: 0x0000 0000, reset by Backup domain Reset.
Access: 0 ≤ wait state ≤ 3, word, half-word and byte access
Wait states are inserted in case of successive accesses to this register.
Note:
31
LSEON, LSEBYP, RTCSEL and RTCEN bits of the Backup domain control register
(RCC_BDCR) are in the Backup domain. As a result, after Reset, these bits are writeprotected and the DBP bit in the Power control register (PWR_CR) has to be set before
these can be modified. Refer to Section 5: Backup registers (BKP) for further information.
These bits are only reset after a Backup domain Reset (see Section 6.1.3: Backup domain
reset). Any internal or external Reset will not have any effect on these bits.
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
BDRST
Reserved
rw
15
14
13
RTC
EN
12
11
10
9
8
7
6
5
RTCSEL[1:0]
Reserved
rw
Reserved
rw
Bits 31:17
rw
4
3
2
1
0
LSE
BYP
LSE
RDY
LSEON
rw
r
rw
Reserved, always read as 0.
Bit 16 BDRST: Backup domain software reset
Set and cleared by software.
0: Reset not activated
1: Resets the entire Backup domain
Bit 15 RTCEN: RTC clock enable
Set and cleared by software.
0: RTC clock disabled
1: RTC clock enabled
Bits 14:10
Reserved, always read as 0.
Bits 9:8 RTCSEL[1:0]: RTC clock source selection
Set by software to select the clock source for the RTC. Once the RTC clock source has been
selected, it cannot be changed anymore unless the Backup domain is reset. The BDRST bit
can be used to reset them.
00: No clock
01: LSE oscillator clock used as RTC clock
10: LSI oscillator clock used as RTC clock
11: HSE oscillator clock divided by 128 used as RTC clock
Bits 7:3
Reserved, always read as 0.
Bit 2 LSEBYP: External low-speed oscillator bypass
Set and cleared by software to bypass oscillator in debug mode. This bit can be written only
when the external 32 kHz oscillator is disabled.
0: LSE oscillator not bypassed
1: LSE oscillator bypassed
Doc ID16188 Rev 5
95/713
99
Reset and clock control (RCC)
RM0041
Bit 1 LSERDY: External low-speed oscillator ready
Set and cleared by hardware to indicate when the external 32 kHz oscillator is stable. After
the LSEON bit is cleared, LSERDY goes low after 6 external low-speed oscillator clock
cycles.
0: External 32 kHz oscillator not ready
1: External 32 kHz oscillator ready
Bit 0 LSEON: External low-speed oscillator enable
Set and cleared by software.
0: External 32 kHz oscillator OFF
1: External 32 kHz oscillator ON
6.3.10
Control/status register (RCC_CSR)
Address: 0x24
Reset value: 0x0C00 0000, reset by system Reset, except reset flags by power Reset only.
Access: 0 ≤ wait state ≤ 3, word, half-word and byte access
Wait states are inserted in case of successive accesses to this register.
31
30
29
28
27
26
25
24
LPWR
RSTF
WWDG
RSTF
IWDG
RSTF
SFT
RSTF
POR
RSTF
PIN
RSTF
Res.
rw
rw
rw
rw
rw
rw
15
14
13
12
11
10
23
22
21
20
19
18
17
16
2
1
0
LSI
RDY
LSION
r
rw
RMVF
Reserved
rw
9
8
7
6
5
Reserved
4
3
Bit 31 LPWRRSTF: Low-power reset flag
Set by hardware when a Low-power management reset occurs.
Cleared by writing to the RMVF bit.
0: No Low-power management reset occurred
1: Low-power management reset occurred
For further information on Low-power management reset, refer to Low-power management
reset.
Bit 30 WWDGRSTF: Window watchdog reset flag
Set by hardware when a window watchdog reset occurs.
Cleared by writing to the RMVF bit.
0: No window watchdog reset occurred
1: Window watchdog reset occurred
Bit 29 IWDGRSTF: Independent watchdog reset flag
Set by hardware when an independent watchdog reset from VDD domain occurs.
Cleared by writing to the RMVF bit.
0: No watchdog reset occurred
1: Watchdog reset occurred
96/713
Doc ID16188 Rev 5
RM0041
Reset and clock control (RCC)
Bit 28 SFTRSTF: Software reset flag
Set by hardware when a software reset occurs.
Cleared by writing to the RMVF bit.
0: No software reset occurred
1: Software reset occurred
Bit 27 PORRSTF: POR/PDR reset flag
Set by hardware when a POR/PDR reset occurs.
Cleared by writing to the RMVF bit.
0: No POR/PDR reset occurred
1: POR/PDR reset occurred
Bit 26 PINRSTF: PIN reset flag
Set by hardware when a reset from the NRST pin occurs.
Cleared by writing to the RMVF bit.
0: No reset from NRST pin occurred
1: Reset from NRST pin occurred
Bit 25
Reserved, always read as 0.
Bit 24 RMVF: Remove reset flag
Set by software to clear the reset flags.
0: No effect
1: Clear the reset flags
Bits 23:2
Reserved, always read as 0.
Bit 1 LSIRDY: Internal low-speed oscillator ready
Set and cleared by hardware to indicate when the internal RC 40 kHz oscillator is stable.
After the LSION bit is cleared, LSIRDY goes low after 3 internal RC 40 kHz oscillator clock
cycles.
0: Internal RC 40 kHz oscillator not ready
1: Internal RC 40 kHz oscillator ready
Bit 0 LSION: Internal low-speed oscillator enable
Set and cleared by software.
0: Internal RC 40 kHz oscillator OFF
1: Internal RC 40 kHz oscillator ON
Doc ID16188 Rev 5
97/713
99
Reset and clock control (RCC)
6.3.11
RM0041
Clock configuration register2 (RCC_CFGR2)
Address offset: 0x2C
Access: no wait state, word, half-word and byte access
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
6
5
4
3
18
17
16
2
1
0
Reserved
15
14
13
12
11
10
9
8
7
PREDIV1[3:0]
Reserved
rw
Bits 31:4
rw
rw
rw
Reserved.
Bits 3:0 PREDIV1[3:0]: PREDIV1 division factor
Set and cleared by software to select the PREDIV1 division factor. These bits can be written
only when the PLL is disabled.
Note: Bit 0 is the same as bit 17 in the RCC_CFGR register, so modifying bit 17 in the
RCC_CFGR register changes bit 0 accordingly.
0000: PREDIV1 input clock not divided
0001: PREDIV1 input clock divided by 2
0010: PREDIV1 input clock divided by 3
0011: PREDIV1 input clock divided by 4
0100: PREDIV1 input clock divided by 5
0101: PREDIV1 input clock divided by 6
0110: PREDIV1 input clock divided by 7
0111: PREDIV1 input clock divided by 8
1000: PREDIV1 input clock divided by 9
1001: PREDIV1 input clock divided by 10
1010: PREDIV1 input clock divided by 11
1011: PREDIV1 input clock divided by 12
1100: PREDIV1 input clock divided by 13
1101: PREDIV1 input clock divided by 14
1110: PREDIV1 input clock divided by 15
1111: PREDIV1 input clock divided by 16
98/713
Doc ID16188 Rev 5
0x024
0x02C
RCC_CSR
Reset value
RCC_CFGR2
Reset value
RCC_BDCR
Reserved
0
0
0
0
1
1
0
0
0
0
0
0
Reset value
0
0
0
Reserved
Doc ID16188 Rev 5
0
0
0
0
0
Reserved
Reserved
Reset value
0
RTC
SEL
[1:0]
0
0
0
0
0
0
0
0
0
0
0
1
Reserved
DMA1EN
1
0
0
AFIOEN
TIM2RST
0
TIM3RST
0
TIM4RST
IOPARST
0
0
0
0
0
0
0
AFIORST
Reserved
0
DMA2EN
0
SRAMEN
0
HSIRDYF
LSERDYF
LSIRDYF
0
TIM2EN
IOPAEN
0
0
PLLRDYF
0
HSERDYF
0
HSIRDY
HSION
Reserved
0
Reserved
IOPBRST
HPRE[3:0]
TIM3EN
IOPCRST
0
0
TIM5RST
0
0
FLITFEN
0
Reserved
0
0
Reserved
IOPDRST
CSSF
PPRE1
[2:0]
1
TIM4EN
IOPBEN
0
TIM6RST
IOPCEN
0
TIM6EN
IOPFRST
IOPERST
0
TIM5EN
0
TIM7RST
0
0
Reserved
IOPDEN
0
TIM7EN
0
TIM12RST
CRCEN
IOPEEN
0
TIM12EN
0
IOPGRST
0
TIM13RST
0
TIM14RST
Reserved
IOPFEN
0
IOPGEN
0
TIM13EN
FSMCEN
Reserved
TIM14EN
HSIRDYIE
0
LSERDYIE
LSIRDYIE
0
Reserved
ADC1
0
Reserved
PPRE2
[2:0]
ADC1EN
PLLRDYIE
0
0
Reserved
0
0
Reserved
0
HSERDYIE
0
0
SPI1RST
0
TIM1RST
0
WWDGRST
0
TIM1EN
0
WWDGEN
0
Reserved
0
SPI1EN
Reserved
0
Reserved
USART1RST
HSEON
ADC
PRE
[1:0]
0
LSEON
0
0
SPI2RST
0
0
Reserved
0
0
USART1EN
HSERDY
0
PLLSRC
PLLMUL[3:0]
PLLXTPRE
CSSON
HSEBYP
0
Reserved
0
SPI2EN
0
Reserved
0
SPI3RST
LSIRDYC
0
Reserved
LSERDYC
0
SPI3EN
0
TIM15RST
0
TIM16RST
0
0
Reserved
USART2RST
HSIRDYC
PLL ON
0
0
0
0
LSION
Reset value
TIM15EN
Reserved
TIM16EN
0
TIM17RST
PLLRDYC
HSERDYC
Reserved
PLL RDY
0
LSEBYP
0
0
HSITRIM[4:0]
LSERDY
0
0
HSICAL[7:0]
LSIRDY
0
USART3RST
Reset value
RTCEN
0
UART4RST
Reserved
Reserved
RCC_AHBENR
USART2EN
RCC_APB2ENR
0
I2C1RST
0
TIM17EN
0
USART3EN
0
Reserved
UART5RST
Reset value
UART4EN
0
0
I2C1EN
RCC_APB2RSTR
0
UART5EN
0
Reserved
MCO [2:0]
I2C2RST
Reserved
CSSC
Reset value
0
I2C2EN
RCC_CIR
Reserved
BKPRST
Reserved
0
Reserved
BDRST
0
BKPEN
Reset value
RMVF
Reset value
DACRST
Reserved
Reserved
PINRSTF
0x020
RCC_APB1ENR
PORRSTF
0x01C
PWRRST
Reset value
DACEN
0x018
RCC_CR
PWREN
0x014
RCC_APB1RSTR
SFTRSTF
0x010
IWDGRSTF
0x00C
RCC_CFGR
CECRST
0x008
Reserved
0x004
CECEN
0x000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Register
Reserved
Offset
LPWRSTF
6.3.12
WWDGRSTF
RM0041
Reset and clock control (RCC)
RCC register map
The following table gives the RCC register map and the reset values.
Table 15. RCC register map and reset values
1
1
SWS
[1:0]
SW
[1:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
PREDIV1[3:0]
0 0 0 0
Refer to Table 1 on page 36 and Table 2 on page 37 for the register boundary addresses.
99/713
99
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7
RM0041
General-purpose and alternate-function I/Os
(GPIOs and AFIOs)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
7.1
GPIO functional description
Each of the general-purpose I/O ports has two 32-bit configuration registers (GPIOx_CRL,
GPIOx_CRH), two 32-bit data registers (GPIOx_IDR, GPIOx_ODR), a 32-bit set/reset
register (GPIOx_BSRR), a 16-bit reset register (GPIOx_BRR) and a 32-bit locking register
(GPIOx_LCKR).
Subject to the specific hardware characteristics of each I/O port listed in the datasheet, each
port bit of the General Purpose IO (GPIO) Ports, can be individually configured by software
in several modes:
•
Input floating
•
Input pull-up
•
Input-pull-down
•
Analog
•
Output open-drain
•
Output push-pull
•
Alternate function push-pull
•
Alternate function open-drain
Each I/O port bit is freely programmable, however the I/O port registers have to be
accessed as 32-bit words (half-word or byte accesses are not allowed). The purpose of the
GPIOx_BSRR and GPIOx_BRR registers is to allow atomic read/modify accesses to any of
the GPIO registers. This way, there is no risk that an IRQ occurs between the read and the
modify access.
Figure 11 shows the basic structure of an I/O Port bit.
100/713
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Figure 11. Basic structure of a standard I/O port bit
on/off
Input data register
Alternate Function Input
on/off
VDD
TTL Schmitt
trigger
VSS
Output driver
I/O pin
VDD
Protection
diode
P-MOS
Output
control
VSS
N-MOS
Read/write
VSS
From on-chip
peripheral
Protection
diode
on/off
Input driver
Output data register
Bit set/reset registers
Read
Write
VDD
Analog Input
To on-chip
peripheral
Push-pull,
open-drain or
disabled
Alternate Function Output
ai14781
Figure 12. Basic structure of a five-volt tolerant I/O port bit
on/off
Input data register
Alternate Function Input
on/off
VDD_FT(1)
TTL Schmitt
trigger
on/off
VSS
Input driver
Output data register
Bit set/reset registers
Read
Write
VDD
Analog Input
To on-chip
peripheral
Output driver
VDD
Protection
diode
P-MOS
Output
control
VSS
N-MOS
Read/write
VSS
From on-chip
peripheral
I/O pin
Alternate Function Output
Push-pull,
open-drain or
disabled
ai14782
1. VDD_FT is a potential specific to five-volt tolerant I/Os and different from VDD.
Doc ID16188 Rev 5
101/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
RM0041
Table 16. Port bit configuration table
Configuration mode
CNF1
General purpose
output
Push-pull
Alternate Function
output
Push-pull
Open-drain
Open-drain
Analog
Input
Input floating
Input pull-down
Input pull-up
0
1
0
1
CNF0
MODE1
0
MODE0
01
10
11
see Table 17
1
0
1
0
PxODR
register
0 or 1
0 or 1
don’t care
don’t care
don’t care
1
00
0
don’t care
0
1
Table 17. Output MODE bits
7.1.1
MODE[1:0]
Meaning
00
Reserved
01
Max. output speed 10 MHz
10
Max. output speed 2 MHz
11
Max. output speed 50 MHz
General-purpose I/O (GPIO)
During and just after reset, the alternate functions are not active and the I/O ports are
configured in Input Floating mode (CNFx[1:0]=01b, MODEx[1:0]=00b).
The JTAG pins are in input PU/PD after reset:
PA15: JTDI in PU
PA14: JTCK in PD
PA13: JTMS in PU
PB4: NJTRST in PU
When configured as output, the value written to the Output Data register (GPIOx_ODR) is
output on the I/O pin. It is possible to use the output driver in Push-Pull mode or Open-Drain
mode (only the N-MOS is activated when outputting 0).
The Input Data register (GPIOx_IDR) captures the data present on the I/O pin at every
APB2 clock cycle.
All GPIO pins have an internal weak pull-up and weak pull-down which can be activated or
not when configured as input.
7.1.2
Atomic bit set or reset
There is no need for the software to disable interrupts when programming the GPIOx_ODR
at bit level: it is possible to modify only one or several bits in a single atomic APB2 write
access. This is achieved by programming to ‘1’ the Bit Set/Reset Register (GPIOx_BSRR,
102/713
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
or for reset only GPIOx_BRR) to select the bits to modify. The unselected bits will not be
modified.
7.1.3
External interrupt/wakeup lines
All ports have external interrupt capability. To use external interrupt lines, the port must be
configured in input mode. For more information on external interrupts, refer to Section 8.2:
External interrupt/event controller (EXTI) and Section 8.2.3: Wakeup event management.
7.1.4
Alternate functions (AF)
It is necessary to program the Port Bit Configuration Register before using a default
alternate function.
•
Note:
For alternate function inputs, the port must be configured in Input mode (floating, pullup or pull-down) and the input pin must be driven externally.
It is also possible to emulate the AFI input pin by software by programming the GPIO
controller. In this case, the port should be configured in Alternate Function Output mode.
And obviously, the corresponding port should not be driven externally as it will be driven by
the software using the GPIO controller.
•
For alternate function outputs, the port must be configured in Alternate Function Output
mode (Push-Pull or Open-Drain).
•
For bidirectional Alternate Functions, the port bit must be configured in Alternate
Function Output mode (Push-Pull or Open-Drain). In this case the input driver is
configured in input floating mode
If a port bit is configured as Alternate Function Output, this disconnects the output register
and connects the pin to the output signal of an on-chip peripheral.
If software configures a GPIO pin as Alternate Function Output, but peripheral is not
activated, its output is not specified.
7.1.5
Software remapping of I/O alternate functions
To optimize the number of peripheral I/O functions for different device packages, it is
possible to remap some alternate functions to some other pins. This is achieved by
software, by programming the corresponding registers (refer to AFIO registers. In that case,
the alternate functions are no longer mapped to their original assignations.
7.1.6
GPIO locking mechanism
The locking mechanism allows the IO configuration to be frozen. When the LOCK sequence
has been applied on a port bit, it is no longer possible to modify the value of the port bit until
the next reset.
Doc ID16188 Rev 5
103/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.1.7
RM0041
Input configuration
When the I/O Port is programmed as Input:
•
The Output Buffer is disabled
•
The Schmitt Trigger Input is activated
•
The weak pull-up and pull-down resistors are activated or not depending on input
configuration (pull-up, pull-down or floating):
•
The data present on the I/O pin is sampled into the Input Data Register every APB2
clock cycle
•
A read access to the Input Data Register obtains the I/O State.
Figure 13 shows the Input Configuration of the I/O Port bit.
Figure 13. Input floating/pull up/pull down configurations
VDD
Input data register
on/off
Read/write
Output data register
Write
Bit set/reset registers
Read
on
VDD or VDD_FT(1)
TTL Schmitt
trigger
protection
diode
on/off
input driver
VSS
I/O pin
output driver
protection
diode
VSS
ai14783
1. VDD_FT is a potential specific to 5-Volt tolerant I/Os and different from VDD.
104/713
Doc ID16188 Rev 5
RM0041
7.1.8
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Output configuration
When the I/O Port is programmed as Output:
•
The Output Buffer is enabled:
–
Open Drain Mode: A “0” in the Output register activates the N-MOS while a “1” in
the Output register leaves the port in Hi-Z. (the P-MOS is never activated)
–
Push-Pull Mode: A “0” in the Output register activates the N-MOS while a “1” in the
Output register activates the P-MOS.
•
The Schmitt Trigger Input is activated.
•
The weak pull-up and pull-down resistors are disabled.
•
The data present on the I/O pin is sampled into the Input Data Register every APB2
clock cycle
•
A read access to the Input Data Register gets the I/O state in open drain mode
•
A read access to the Output Data register gets the last written value in Push-Pull mode
Figure 14 shows the Output configuration of the I/O Port bit.
Input data register
Figure 14. Output configuration
Read/write
Output data register
Write
Bit set/reset registers
Read
on
VDD or VDD_FT(1)
TTL Schmitt
trigger
Protection
diode
Input driver
I/O pin
Output driver
VDD
Protection
diode
P-MOS
Output
control
VSS
N-MOS
Push-pull or
VSS
Open-drain
ai14784
1. VDD_FT is a potential specific to 5-V tolerant I/Os and different from VDD.
Doc ID16188 Rev 5
105/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.1.9
RM0041
Alternate function configuration
When the I/O Port is programmed as Alternate Function:
•
The Output Buffer is turned on in Open Drain or Push-Pull configuration
•
The Output Buffer is driven by the signal coming from the peripheral (alternate function
out)
•
The Schmitt Trigger Input is activated
•
The weak pull-up and pull-down resistors are disabled.
•
The data present on the I/O pin is sampled into the Input Data Register every APB2
clock cycle
•
A read access to the Input Data Register gets the I/O state in open drain mode
•
A read access to the Output Data register gets the last written value in Push-Pull mode
Figure 15 shows the Alternate Function Configuration of the I/O Port bit. Also, refer to
Section 7.4: AFIO registers for further information.
A set of Alternate Function I/O registers allows the user to remap some alternate functions
to different pins. Refer to Section 7.3: Alternate function I/O and debug configuration (AFIO).
Figure 15. Alternate function configuration
Input data register
Alternate Function Input
To on-chip
peripheral
Read/write
Output data register
Write
Bit set/reset registers
Read
on
VDD or VDD_FT(1)
TTL Schmitt
trigger
Protection
diode
Input driver
Output driver
I/O pin
VDD
P-MOS
Output
control
VSS
N-MOS
VSS
From on-chip
peripheral
Protection
diode
push-pull or
open-drain
Alternate Function Output
ai14785
1. VDD_FT is a potential specific to 5-Volt tolerant I/Os and different from VDD.
106/713
Doc ID16188 Rev 5
RM0041
7.1.10
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Analog configuration
When the I/O Port is programmed as Analog configuration:
•
The Output Buffer is disabled.
•
The Schmitt Trigger Input is de-activated providing zero consumption for every analog
value of the I/O pin. The output of the Schmitt Trigger is forced to a constant value (0).
•
The weak pull-up and pull-down resistors are disabled.
•
Read access to the Input Data Register gets the value “0”.
Figure 16 shows the high impedance-analog configuration of the I/O Port bit.
Figure 16. High impedance-analog configuration
Input data register
Analog Input
To on-chip
peripheral
Read/write
Output data register
Write
Bit set/reset registers
Read
off
0
VDD or VDD_FT(1)
TTL Schmitt
trigger
Protection
diode
Input driver
I/O pin
Protection
diode
VSS
From on-chip
peripheral
7.1.11
ai14786
GPIO configurations for device peripherals
Table 18 to Table 27 give the GPIO configurations of the device peripherals.
Table 18. Advanced timer TIM1
TIM1 pinout
Configuration
GPIO configuration
Input capture channel x
Input floating
Output compare channel x
Alternate function push-pull
TIM1_CHxN
Complementary output channel x
Alternate function push-pull
TIM1_BKIN
Break input
Input floating
TIM1_ETR
External trigger timer input
Input floating
TIM1_CHx
Doc ID16188 Rev 5
107/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
RM0041
Table 19. General-purpose timers TIM2/3/4/5
TIM2/3/4/5 pinout
Configuration
TIM2/3/4/5_CHx
TIM2/3/4/5_ETR
GPIO configuration
Input capture channel x
Input floating
Output compare channel x
Alternate function push-pull
External trigger timer input
Input floating
Table 20. General-purpose timers TIM15/16/17
TIM15/16/17 pinout
Configuration
GPIO configuration
Input capture channel x
Input floating
Output compare channel x
Alternate function push-pull
TIM15/16/17_CHxN
Complementary output channel x
Alternate function push-pull
TIM15/16/17_BKIN
Break input
Input floating
TIM15/16/17_ETR
External trigger timer input
Input floating
TIM15/16/17_CHx
Table 21. General-purpose timers TIM12/13/14
TIM12/13/14 pinout
TIM12/13/14_CHx
Configuration
GPIO configuration
Input capture channel x
Input floating
Output compare channel x
Alternate function push-pull
Table 22. USARTs
USART pinout
Configuration
GPIO configuration
Full duplex
Alternate function push-pull
Half duplex synchronous mode
Alternate function push-pull
Full duplex
Input floating / Input pull-up
Half duplex synchronous mode
Not used. Can be used as a general IO
USARTx_CK
Synchronous mode
Alternate function push-pull
USARTx_RTS
Hardware flow control
Alternate function push-pull
USARTx_CTS
Hardware flow control
Input floating/ Input pull-up
USARTx_TX(1)
USARTx_RX
1. The USART_TX pin can also be configured as alternate function open drain.
Table 23. SPI
SPI pinout
SPIx_SCK
108/713
Configuration
GPIO configuration
Master
Alternate function push-pull
Slave
Input floating
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Table 23. SPI (continued)
SPI pinout
SPIx_MOSI
Configuration
GPIO configuration
Full duplex / master
Alternate function push-pull
Full duplex / slave
Input floating / Input pull-up
Simplex bidirectional data wire / master
Alternate function push-pull
Simplex bidirectional data wire/ slave
Not used. Can be used as a GPIO
Full duplex / master
Input floating / Input pull-up
Full duplex / slave (point to point)
Alternate function push-pull
Full duplex / slave (multi-slave)
Alternate function open drain
SPIx_MISO Simplex bidirectional data wire / master
SPIx_NSS
Not used. Can be used as a GPIO
Simplex bidirectional data wire/ slave
(point to point)
Alternate function push-pull
Simplex bidirectional data wire/ slave
(multi-slave)
Alternate function open drain
Hardware master /slave
Input floating/ Input pull-up / Input pull-down
Hardware master/ NSS output enabled
Alternate function push-pull
Software
Not used. Can be used as a GPIO
Table 24. CEC
CEC pinout
Configuration
CEC
CEC line
GPIO configuration
Alternate function open drain
Table 25. I2C
I2C pinout
Configuration
GPIO configuration
I2Cx_SCL
I2C clock
Alternate function open drain
I2Cx_SDA
I2C Data I/O
Alternate function open drain
The GPIO configuration of the ADC inputs should be analog.
Figure 17. ADC / DAC
ADC/DAC pin
ADC/DAC
GPIO configuration
Analog
Table 26. FSMC
FSMC pinout
GPIO configuration
FSMC_A[25:0]
FSMC_D[15:0]
Alternate function push-pull
FSMC_CK
Alternate function push-pull
Doc ID16188 Rev 5
109/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
RM0041
Table 26. FSMC
FSMC pinout
GPIO configuration
FSMC_NOE
FSMC_NWE
Alternate function push-pull
FSMC_NE[4:1]
Alternate function push-pull
FSMC_NWAIT
Input floating/ Input pull-up
FSMC_NL
FSMC_NBL[1:0]
Alternate function push-pull
Table 27. Other IOs
Pins
RTC output
GPIO configuration
Tamper event input
Forced by hardware when configuring the
BKP_CR and BKP_RTCCR registers
MCO
Clock output
Alternate function push-pull
EXTI input lines
External input interrupts
Input floating / input pull-up / input pull-down
TAMPER-RTC pin
110/713
Alternate function
Doc ID16188 Rev 5
RM0041
7.2
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
GPIO registers
Refer to Section 1.1 on page 32 for a list of abbreviations used in register descriptions.
The peripheral registers have to be accessed by words (32-bit).
7.2.1
Port configuration register low (GPIOx_CRL) (x=A..G)
Address offset: 0x00
Reset value: 0x4444 4444
31
30
29
28
27
26
25
24
23
22
20
18
16
MODE7[1:0]
CNF6[1:0]
MODE6[1:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CNF2[1:0]
MODE2[1:0]
rw
rw
rw
rw
rw
rw
rw
rw
CNF1[1:0]
rw
rw
MODE1[1:0]
rw
rw
CNF4[1:0]
17
CNF7[1:0]
MODE3[1:0]
MODE5[1:0]
19
rw
CNF3[1:0]
CNF5[1:0]
21
CNF0[1:0]
rw
rw
MODE4[1:0]
MODE0[1:0]
rw
rw
Bits 31:30, 27:26, CNFy[1:0]: Port x configuration bits (y= 0 .. 7)
23:22, 19:18, 15:14,
These bits are written by software to configure the corresponding I/O port.
11:10, 7:6, 3:2
Refer to Table 16: Port bit configuration table.
In input mode (MODE[1:0]=00):
00: Analog mode
01: Floating input (reset state)
10: Input with pull-up / pull-down
11: Reserved
In output mode (MODE[1:0] > 00):
00: General purpose output push-pull
01: General purpose output Open-drain
10: Alternate function output Push-pull
11: Alternate function output Open-drain
Bits 29:28, 25:24, MODEy[1:0]: Port x mode bits (y= 0 .. 7)
21:20, 17:16, 13:12,
These bits are written by software to configure the corresponding I/O port.
9:8, 5:4, 1:0
Refer to Table 16: Port bit configuration table.
00: Input mode (reset state)
01: Output mode, max speed 10 MHz.
10: Output mode, max speed 2 MHz.
11: Output mode, max speed 50 MHz.
Doc ID16188 Rev 5
111/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.2.2
RM0041
Port configuration register high (GPIOx_CRH) (x=A..G)
Address offset: 0x04
Reset value: 0x4444 4444
31
30
29
CNF15[1:0]
28
MODE15[1:0]
27
26
CNF14[1:0]
25
24
23
MODE14[1:0]
22
CNF13[1:0]
21
20
MODE13[1:0]
19
18
CNF12[1:0]
17
16
MODE12[1:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CNF11[1:0]
rw
MODE11[1:0]
rw
rw
rw
CNF10[1:0]
rw
MODE10[1:0]
rw
rw
rw
CNF9[1:0]
rw
rw
MODE9[1:0]
rw
rw
CNF8[1:0]
rw
rw
MODE8[1:0]
rw
rw
Bits 31:30, 27:26, CNFy[1:0]: Port x configuration bits (y= 8 .. 15)
23:22, 19:18, 15:14,
These bits are written by software to configure the corresponding I/O port.
11:10, 7:6, 3:2
Refer to Table 16: Port bit configuration table.
In input mode (MODE[1:0]=00):
00: Analog mode
01: Floating input (reset state)
10: Input with pull-up / pull-down
11: Reserved
In output mode (MODE[1:0] > 00):
00: General purpose output push-pull
01: General purpose output Open-drain
10: Alternate function output Push-pull
11: Alternate function output Open-drain
Bits 29:28, 25:24, MODEy[1:0]: Port x mode bits (y= 8 .. 15)
21:20, 17:16, 13:12,
These bits are written by software to configure the corresponding I/O port.
9:8, 5:4, 1:0
Refer to Table 16: Port bit configuration table.
00: Input mode (reset state)
01: Output mode, max speed 10 MHz.
10: Output mode, max speed 2 MHz.
11: Output mode, max speed 50 MHz.
7.2.3
Port input data register (GPIOx_IDR) (x=A..G)
Address offset: 0x08h
Reset value: 0x0000 XXXX
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Reserved
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
IDR15
IDR14
IDR13
IDR12
IDR11
IDR10
IDR9
IDR8
IDR7
IDR6
IDR5
IDR4
IDR3
IDR2
IDR1
IDR0
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
Bits 31:16
Reserved, must be kept at reset value.
Bits 15:0 IDRy: Port input data (y= 0 .. 15)
These bits are read only and can be accessed in Word mode only. They contain the input
value of the corresponding I/O port.
112/713
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.2.4
Port output data register (GPIOx_ODR) (x=A..G)
Address offset: 0x0C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Reserved
15
14
13
12
11
10
ODR15 ODR14 ODR13 ODR12 ODR11 ODR10
rw
rw
rw
Bits 31:16
rw
rw
rw
9
8
7
6
5
4
3
2
1
0
ODR9
ODR8
ODR7
ODR6
ODR5
ODR4
ODR3
ODR2
ODR1
ODR0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Reserved, must be kept at reset value.
Bits 15:0 ODRy: Port output data (y= 0 .. 15)
These bits can be read and written by software and can be accessed in Word mode only.
Note: For atomic bit set/reset, the ODR bits can be individually set and cleared by writing to
the GPIOx_BSRR register (x = A .. E).
7.2.5
Port bit set/reset register (GPIOx_BSRR) (x=A..G)
Address offset: 0x10
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
BR15
BR14
BR13
BR12
BR11
BR10
BR9
BR8
BR7
BR6
BR5
BR4
BR3
BR2
BR1
BR0
w
w
w
w
w
w
w
w
w
w
w
w
w
w
w
w
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
BS15
BS14
BS13
BS12
BS11
BS10
BS9
BS8
BS7
BS6
BS5
BS4
BS3
BS2
BS1
BS0
w
w
w
w
w
w
w
w
w
w
w
w
w
w
w
w
Bits 31:16 BRy: Port x Reset bit y (y= 0 .. 15)
These bits are write-only and can be accessed in Word mode only.
0: No action on the corresponding ODRx bit
1: Reset the corresponding ODRx bit
Note: If both BSx and BRx are set, BSx has priority.
Bits 15:0 BSy: Port x Set bit y (y= 0 .. 15)
These bits are write-only and can be accessed in Word mode only.
0: No action on the corresponding ODRx bit
1: Set the corresponding ODRx bit
Doc ID16188 Rev 5
113/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.2.6
RM0041
Port bit reset register (GPIOx_BRR) (x=A..G)
Address offset: 0x14
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Reserved
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
BR15
BR14
BR13
BR12
BR11
BR10
BR9
BR8
BR7
BR6
BR5
BR4
BR3
BR2
BR1
BR0
w
w
w
w
w
w
w
w
w
w
w
w
w
w
w
w
Bits 31:16
Reserved
Bits 15:0 BRy: Port x Reset bit y (y= 0 .. 15)
These bits are write-only and can be accessed in Word mode only.
0: No action on the corresponding ODRx bit
1: Reset the corresponding ODRx bit
7.2.7
Port configuration lock register (GPIOx_LCKR) (x=A..G)
This register is used to lock the configuration of the port bits when a correct write sequence
is applied to bit 16 (LCKK). The value of bits [15:0] is used to lock the configuration of the
GPIO. During the write sequence, the value of LCKR[15:0] must not change. When the
LOCK sequence has been applied on a port bit it is no longer possible to modify the value of
the port bit until the next reset.
Each lock bit freezes the corresponding 4 bits of the control register (CRL, CRH).
Address offset: 0x18
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
LCKK
Reserved
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
LCK15
LCK14
LCK13
LCK12
LCK11
LCK10
LCK9
LCK8
LCK7
LCK6
LCK5
LCK4
LCK3
LCK2
LCK1
LCK0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
114/713
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Bits 31:17
Reserved
Bit 16 LCKK[16]: Lock key
This bit can be read anytime. It can only be modified using the Lock Key Writing Sequence.
0: Port configuration lock key not active
1: Port configuration lock key active. GPIOx_LCKR register is locked until the next reset.
LOCK key writing sequence:
Write 1
Write 0
Write 1
Read 0
Read 1 (this read is optional but confirms that the lock is active)
Note: During the LOCK Key Writing sequence, the value of LCK[15:0] must not change.
Any error in the lock sequence will abort the lock.
Bits 15:0 LCKy: Port x Lock bit y (y= 0 .. 15)
These bits are read write but can only be written when the LCKK bit is 0.
0: Port configuration not locked
1: Port configuration locked.
7.3
Alternate function I/O and debug configuration (AFIO)
To optimize the number of peripherals available for the 64-pin or the 100-pin or the 144-pin
package, it is possible to remap some alternate functions to some other pins. This is
achieved by software, by programming the AF remap and debug I/O configuration register
(AFIO_MAPR). In this case, the alternate functions are no longer mapped to their original
assignations.
7.3.1
Using OSC32_IN/OSC32_OUT pins as GPIO ports PC14/PC15
The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general-purpose I/O
PC14 and PC15, respectively, when the LSE oscillator is off. The LSE has priority over the
GP IOs function.
Note:
The PC14/PC15 GPIO functionality is lost when the 1.8 V domain is powered off (by
entering standby mode) or when the backup domain is supplied by VBAT (VDD no more
supplied). In this case the IOs are set in analog mode.
Refer to the note on IO usage restrictions in Section 4.1.2: Battery backup domain.
7.3.2
Using OSC_IN/OSC_OUT pins as GPIO ports PD0/PD1
The HSE oscillator pins OSC_IN/OSC_OUT can be used as general-purpose I/O PD0/PD1
by programming the PD01_REMAP bit in the AF remap and debug I/O configuration register
(AFIO_MAPR).
This remap is available only on 48- and 64-pin packages (PD0 and PD1 are available on
100-pin and 144-pin packages, no need for remapping).
Note:
The external interrupt/event function is not remapped. PD0 and PD1 cannot be used for
external interrupt/event generation on 48- and 64-pin packages.
Doc ID16188 Rev 5
115/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.3.3
RM0041
JTAG/SWD alternate function remapping
The debug interface signals are mapped on the GPIO ports as shown in Table 28.
Table 28. Debug interface signals
Alternate function
GPIO port
JTMS / SWDIO
PA13
JTCK / SWCLK
PA14
JTDI
PA15
JTDO / TRACESWO
PB3
NJTRST
PB4
TRACECK
PE2
TRACED0
PE3
TRACED1
PE4
TRACED2
PE5
TRACED3
PE6
To optimize the number of free GPIOs during debugging, this mapping can be configured in
different ways by programming the SWJ_CFG[1:0] bits in the AF remap and debug I/O
configuration register (AFIO_MAPR). Refer to Table 29
Table 29. Debug port mapping
SWJ I/O pin assigned
SWJ _CFG
[2:0]
Available debug ports
000
PA13 /
JTMS/
SWDIO
PA14 /
JTCK/S
WCLK
PA15 /
JTDI
Full SWJ (JTAG-DP + SW-DP)
(Reset state)
X
X
X
X
X
001
Full SWJ (JTAG-DP + SW-DP)
but without NJTRST
X
X
X
x
free
010
JTAG-DP Disabled and
SW-DP Enabled
X
X
free
free(1)
free
100
JTAG-DP Disabled and
SW-DP Disabled
free
free
free
free
free
-
-
-
-
-
Other
Forbidden
PB3 / JTDO/
PB4/
TRACE
NJTRST
SWO
1. Released only if not using asynchronous trace.
7.3.4
Timer alternate function remapping
Timer 4 channels 1 to 4 can be remapped from Port B to Port D. Other timer remapping
possibilities are listed in Table 35 to Table 37. Refer to AF remap and debug I/O
configuration register (AFIO_MAPR).
116/713
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Table 30. TIM5 alternate function remapping(1)
Alternate function
TIM5_CH4
TIM5CH4_IREMAP = 0
TIM5CH4_IREMAP = 1
TIM5 Channel 4 is
connected to PA3
LSI internal clock is connected to TIM5_CH4
input for calibration purpose.
1. Remap available only for high-density value line devices.
Table 31. TIM12 remapping(1)
Alternate function
TIM12_REMAP = 0
TIM12_REMAP = 1
TIM12_CH1
PC4
PB12
TIM12_CH2
PC5
PB13
1. Refer to the AF remap and debug I/O configuration register Section 7.4.7: AF remap and debug I/O
configuration register (AFIO_MAPR2). Remap available only for high-density value line devices.
Table 32. TIM13 remapping(1)
Alternate function
TIM13_CH1
TIM13_REMAP = 0
TIM13_REMAP = 1
PC8
PB0
1. Refer to the AF remap and debug I/O configuration register Section 7.4.7: AF remap and debug I/O
configuration register (AFIO_MAPR2). Remap available only for high-density value line devices.
Table 33. TIM14 remapping(1)
Alternate function
TIM14_CH1
TIM14_REMAP = 0
TIM14_REMAP = 1
PC9
PB1
1. Refer to the AF remap and debug I/O configuration register Section 7.4.7: AF remap and debug I/O
configuration register (AFIO_MAPR2). Remap available only for high-density value line devices.
Table 34. TIM4 alternate function remapping
Alternate function
TIM4_REMAP = 0
TIM4_REMAP = 1(1)
TIM4_CH1
PB6
PD12
TIM4_CH2
PB7
PD13
TIM4_CH3
PB8
PD14
TIM4_CH4
PB9
PD15
1. Remap available only for 100-pin and for 144-pin package.
Table 35. TIM3 alternate function remapping
Alternate function
TIM3_REMAP[1:0] = TIM3_REMAP[1:0] = TIM3_REMAP[1:0] =
“00” (no remap)
“10” (partial remap) “11” (full remap) (1)
TIM3_CH1
PA6
PB4
PC6
TIM3_CH2
PA7
PB5
PC7
TIM3_CH3
PB0
PC8
TIM3_CH4
PB1
PC9
Doc ID16188 Rev 5
117/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
RM0041
1. Remap available only for 64-pin, 100-pin and 144-pin packages.
Table 36. TIM2 alternate function remapping
Alternate function
TIM2_REMAP[1:
0] = “00” (no
remap)
TIM2_REMAP[1:
0] = “01” (partial
remap)
TIM2_REMAP[1:
0] = “10” (partial
remap)
TIM2_REMAP[1:
0] = “11” (full
remap)
TIM2_CH1_ETR(1)
PA0
PA15
PA0
PA15
TIM2_CH2
PA1
PB3
PA1
PB3
TIM2_CH3
PA2
PB10
TIM2_CH4
PA3
PB11
1. TIM_CH1 and TIM_ETR share the same pin but cannot be used at the same time (which is why we have
this notation: TIM2_CH1_ETR).
Table 37. TIM1 alternate function remapping
Alternate functions
mapping
TIM1_REMAP[1:0] = TIM1_REMAP[1:0] = TIM1_REMAP[1:0] =
“00” (no remap)
“01” (partial remap) “11” (full remap) (1)
TIM1_ETR
PA12
PE7
TIM1_CH1
PA8
PE9
TIM1_CH2
PA9
PE11
TIM1_CH3
PA10
PE13
TIM1_CH4
PA11
PE14
TIM1_BKIN
PB12
PA6
PE15
TIM1_CH1N
PB13
PA7
PE8
TIM1_CH2N
PB14 (2)
PB0
PE10
TIM1_CH3N
(2)
PB1
PE12
PB15
1. Remap available only for 100-pin and 144-pin packages.
Table 38. TIM1 DMA remapping(1)
DMA requests
TIM1_DMA_REMAP = 0
TIM1_DMA_REMAP = 1
TIM1_CH1 DMA request
Mapped on DMA1 Channel2
Mapped on DMA1 Channel6
TIM1_CH2 DMA request
Mapped on DMA1 Channel3
Mapped on DMA1 Channel6
1. Refer to the AF remap and debug I/O configuration register Section 7.4.7: AF remap and debug I/O
configuration register (AFIO_MAPR2).
Table 39. TIM15 remapping(1)
Alternate function
TIM15_REMAP = 0
TIM15_REMAP = 1
TIM15_CH1
PA2
PB14
TIM15_CH2
PA3
PB15
1. Refer to the AF remap and debug I/O configuration register Section 7.4.7: AF remap and debug I/O
configuration register (AFIO_MAPR2).
118/713
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Table 40. TIM16 remapping(1)
Alternate function
TIM16_CH1
TIM16_REMAP = 0
PB8
TIM16_REMAP = 1
PA6
1. Refer to the AF remap and debug I/O configuration register Section 7.4.7: AF remap and debug I/O
configuration register (AFIO_MAPR2).
Table 41. TIM17 remapping(1)
Alternate function
TIM17_CH1
TIM17_REMAP = 0
PB9
TIM17_REMAP = 1
PA7
1. Refer to the AF remap and debug I/O configuration register Section 7.4.7: AF remap and debug I/O
configuration register (AFIO_MAPR2).
7.3.5
USART alternate function remapping
Refer to AF remap and debug I/O configuration register (AFIO_MAPR).
Table 42. USART3 remapping
Alternate function
USART3_REMAP[1:0]
= “00” (no remap)
USART3_REMAP[1:0] =
“01” (partial remap) (1)
USART3_REMAP[1:0]
= “11” (full remap) (2)
USART3_TX
PB10
PC10
PD8
USART3_RX
PB11
PC11
PD9
USART3_CK
PB12
PC12
PD10
USART3_CTS
PB13
PD11
USART3_RTS
PB14
PD12
1. Remap available only for 64-pin, 100-pin and 144-pin packages
2. Remap available only for 100-pin and 144-pin packages.
Table 43. USART2 remapping
Alternate functions
USART2_REMAP = 0
USART2_REMAP = 1(1)
USART2_CTS
PA0
PD3
USART2_RTS
PA1
PD4
USART2_TX
PA2
PD5
USART2_RX
PA3
PD6
USART2_CK
PA4
PD7
1. Remap available only for 100-pin and 144-pin packages.
Table 44. USART1 remapping
Alternate function
USART1_REMAP = 0
USART1_REMAP = 1
USART1_TX
PA9
PB6
USART1_RX
PA10
PB7
Doc ID16188 Rev 5
119/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.3.6
RM0041
I2C1 alternate function remapping
Refer to AF remap and debug I/O configuration register (AFIO_MAPR)
Table 45. I2C1 remapping
7.3.7
Alternate function
I2C1_REMAP = 0
I2C1_REMAP = 1
I2C1_SCL
PB6
PB8
I2C1_SDA
PB7
PB9
SPI1 alternate function remapping
Refer to AF remap and debug I/O configuration register (AFIO_MAPR)
Table 46. SPI1 remapping
7.3.8
Alternate function
SPI1_REMAP = 0
SPI1_REMAP = 1
SPI1_NSS
PA4
PA15
SPI1_SCK
PA5
PB3
SPI1_MISO
PA6
PB4
SPI1_MOSI
PA7
PB5
CEC remap
Refer to Section 7.4.7: AF remap and debug I/O configuration register (AFIO_MAPR2).
Table 47. CEC remapping
120/713
Alternate function
CEC_REMAP = 0
CEC_REMAP = 1
CEC
PB8
PB10
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.4
AFIO registers
Refer to Section 1.1 on page 32 for a list of abbreviations used in register descriptions.
Note:
To read/write the AFIO_EVCR, AFIO_MAPR, AFIO_MAPR2 and AFIO_EXTICRX registers,
the AFIO clock should first be enabled. Refer to APB2 peripheral clock enable register
(RCC_APB2ENR).
The peripheral registers have to be accessed by words (32-bit).
7.4.1
Event control register (AFIO_EVCR)
Address offset: 0x00
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
rw
rw
rw
Reserved
15
14
13
12
11
10
9
8
7
EVOE
PORT[2:0]
PIN[3:0]
Reserved
rw
rw
rw
rw
rw
Bits 31:8 Reserved
Bit 7 EVOE: Event output enable
Set and cleared by software. When set the EVENTOUT Cortex® output is connected to the
I/O selected by the PORT[2:0] and PIN[3:0] bits.
Bits 3:0 PIN[3:0]: Pin selection (x = A .. E)
Set and cleared by software. Select the pin used to output the Cortex® EVENTOUT signal.
0000: Px0 selected
0001: Px1 selected
0010: Px2 selected
0011: Px3 selected
...
1111: Px15 selected
Doc ID16188 Rev 5
121/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.4.2
RM0041
AF remap and debug I/O configuration register (AFIO_MAPR)
Address offset: 0x04
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
SWJ_CFG[2:0]
Reserved
15
PD01_
REMA
P
14
13
Reserved
rw
Reserved
12
TIM4_
REMA
P
rw
11
w
w
w
10
9
8
TIM3_REMAP
[1:0]
rw
rw
TIM2_REMAP
[1:0]
rw
rw
16
TIM5C
H4_IRE
MAP
rw
7
6
TIM1_REMAP
[1:0]
rw
rw
5
4
USART3_
REMAP[1:0]
rw
rw
3
2
USART2 USART1
_
_
REMAP REMAP
rw
rw
1
0
I2C1_
REMA
P
SPI1_
REMA
P
rw
rw
Bits 31:27 Reserved
Bits 26:24 SWJ_CFG[2:0]: Serial wire JTAG configuration
These bits are write-only (when read, the value is undefined). They are used to configure the
SWJ and trace alternate function I/Os. The SWJ (Serial Wire JTAG) supports JTAG or SWD
access to the Cortex® debug port. The default state after reset is SWJ ON without trace.
This allows JTAG or SW mode to be enabled by sending a specific sequence on the JTMS /
JTCK pin.
000: Full SWJ (JTAG-DP + SW-DP): Reset State
001: Full SWJ (JTAG-DP + SW-DP) but without NJTRST
010: JTAG-DP Disabled and SW-DP Enabled
100: JTAG-DP Disabled and SW-DP Disabled
Other combinations: no effect
Bits 23:17 Reserved.
Bit 15 PD01_REMAP: Port D0/Port D1 mapping on OSC_IN/OSC_OUT
This bit is set and cleared by software. It controls the mapping of PD0 and PD1 GPIO
functionality. When the HSE oscillator is not used (application running on internal 8 MHz RC)
PD0 and PD1 can be mapped on OSC_IN and OSC_OUT. This is available only on 48- and
64-pin packages (PD0 and PD1 are available on 100-pin packages, no need for remapping).
0: No remapping of PD0 and PD1
1: PD0 remapped on OSC_IN, PD1 remapped on OSC_OUT,
Bits 14:13
Reserved.
Bit 12 TIM4_REMAP: TIM4 remapping
This bit is set and cleared by software. It controls the mapping of TIM4 channels 1 to 4 onto
the GPIO ports.
0: No remap (TIM4_CH1/PB6, TIM4_CH2/PB7, TIM4_CH3/PB8, TIM4_CH4/PB9)
1: Full remap (TIM4_CH1/PD12, TIM4_CH2/PD13, TIM4_CH3/PD14, TIM4_CH4/PD15)
Note: TIM4_ETR on PE0 is not re-mapped.
Bits 11:10 TIM3_REMAP[1:0]: TIM3 remapping
These bits are set and cleared by software. They control the mapping of TIM3 channels 1 to
4 on the GPIO ports.
00: No remap (CH1/PA6, CH2/PA7, CH3/PB0, CH4/PB1)
01: Not used
10: Partial remap (CH1/PB4, CH2/PB5, CH3/PB0, CH4/PB1)
11: Full remap (CH1/PC6, CH2/PC7, CH3/PC8, CH4/PC9)
Note: TIM3_ETR on PE0 is not re-mapped.
122/713
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Bits 9:8 TIM2_REMAP[1:0]: TIM2 remapping
These bits are set and cleared by software. They control the mapping of TIM2 channels 1 to
4 and external trigger (ETR) on the GPIO ports.
00: No remap (CH1/ETR/PA0, CH2/PA1, CH3/PA2, CH4/PA3)
01: Partial remap (CH1/ETR/PA15, CH2/PB3, CH3/PA2, CH4/PA3)
10: Partial remap (CH1/ETR/PA0, CH2/PA1, CH3/PB10, CH4/PB11)
11: Full remap (CH1/ETR/PA15, CH2/PB3, CH3/PB10, CH4/PB11)
Bits 7:6 TIM1_REMAP[1:0]: TIM1 remapping
These bits are set and cleared by software. They control the mapping of TIM1 channels 1 to
4, 1N to 3N, external trigger (ETR) and Break input (BKIN) on the GPIO ports.
00: No remap (ETR/PA12, CH1/PA8, CH2/PA9, CH3/PA10, CH4/PA11, BKIN/PB12,
CH1N/PB13, CH2N/PB14, CH3N/PB15)
01: Partial remap (ETR/PA12, CH1/PA8, CH2/PA9, CH3/PA10, CH4/PA11, BKIN/PA6,
CH1N/PA7, CH2N/PB0, CH3N/PB1)
10: not used
11: Full remap (ETR/PE7, CH1/PE9, CH2/PE11, CH3/PE13, CH4/PE14, BKIN/PE15,
CH1N/PE8, CH2N/PE10, CH3N/PE12)
Bits 5:4 USART3_REMAP[1:0]: USART3 remapping
These bits are set and cleared by software. They control the mapping of USART3 CTS,
RTS,CK,TX and RX alternate functions on the GPIO ports.
00: No remap (TX/PB10, RX/PB11, CK/PB12, CTS/PB13, RTS/PB14)
01: Partial remap (TX/PC10, RX/PC11, CK/PC12, CTS/PB13, RTS/PB14)
10: not used
11: Full remap (TX/PD8, RX/PD9, CK/PD10, CTS/PD11, RTS/PD12)
Bit 3 USART2_REMAP: USART2 remapping
This bit is set and cleared by software. It controls the mapping of USART2 CTS, RTS,CK,TX
and RX alternate functions on the GPIO ports.
0: No remap (CTS/PA0, RTS/PA1, TX/PA2, RX/PA3, CK/PA4)
1: Remap (CTS/PD3, RTS/PD4, TX/PD5, RX/PD6, CK/PD7)
Bit 2 USART1_REMAP: USART1 remapping
This bit is set and cleared by software. It controls the mapping of USART1 TX and RX
alternate functions on the GPIO ports.
0: No remap (TX/PA9, RX/PA10)
1: Remap (TX/PB6, RX/PB7)
Bit 1 I2C1_REMAP: I2C1 remapping
This bit is set and cleared by software. It controls the mapping of I2C1 SCL and SDA
alternate functions on the GPIO ports.
0: No remap (SCL/PB6, SDA/PB7)
1: Remap (SCL/PB8, SDA/PB9)
Bit 0 SPI1_REMAP: SPI1 remapping
This bit is set and cleared by software. It controls the mapping of SPI1 NSS, SCK, MISO,
MOSI alternate functions on the GPIO ports.
0: No remap (NSS/PA4, SCK/PA5, MISO/PA6, MOSI/PA7)
1: Remap (NSS/PA15, SCK/PB3, MISO/PB4, MOSI/PB5)
Doc ID16188 Rev 5
123/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.4.3
RM0041
External interrupt configuration register 1 (AFIO_EXTICR1)
Address offset: 0x08
Reset value: 0x0000
31
30
29
28
27
26
25
24
23
22
21
20
19
6
5
4
3
18
17
16
2
1
0
Reserved
15
14
13
12
11
EXTI3[3:0]
rw
rw
rw
Bits 31:16
10
9
8
7
EXTI2[3:0]
rw
rw
rw
rw
EXTI1[3:0]
rw
rw
rw
rw
EXTI0[3:0]
rw
rw
rw
rw
rw
Reserved
Bits 15:0 EXTIx[3:0]: EXTI x configuration (x= 0 to 3)
These bits are written by software to select the source input for EXTIx external interrupt.
Refer to Section 8.2.5: External interrupt/event line mapping
0000: PA[x] pin
0001: PB[x] pin
0010: PC[x] pin
0011: PD[x] pin
0100: PE[x] pin
0101: PF[x] pin
0110: PG[x] pin
7.4.4
External interrupt configuration register 2 (AFIO_EXTICR2)
Address offset: 0x0C
Reset value: 0x0000
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
20
19
6
5
4
3
18
17
16
2
1
0
Reserved
EXTI7[3:0]
rw
rw
rw
Bits 31:16
7
EXTI6[3:0]
rw
rw
rw
rw
EXTI5[3:0]
rw
rw
rw
rw
EXTI4[3:0]
rw
rw
rw
rw
Reserved
Bits 15:0 EXTIx[3:0]: EXTI x configuration (x= 4 to 7)
These bits are written by software to select the source input for EXTIx external interrupt.
0000: PA[x] pin
0001: PB[x] pin
0010: PC[x] pin
0011: PD[x] pin
0100: PE[x] pin
0101: PF[x] pin
0110: PG[x] pin
124/713
Doc ID16188 Rev 5
rw
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.4.5
External interrupt configuration register 3 (AFIO_EXTICR3)
Address offset: 0x10
Reset value: 0x0000
31
30
29
28
27
26
25
24
23
22
21
20
19
6
5
4
3
18
17
16
2
1
0
Reserved
15
14
13
12
11
EXTI11[3:0]
rw
rw
rw
Bits 31:16
10
9
8
7
EXTI10[3:0]
rw
rw
rw
rw
EXTI9[3:0]
rw
rw
rw
rw
EXTI8[3:0]
rw
rw
rw
rw
rw
Reserved
Bits 15:0 EXTIx[3:0]: EXTI x configuration (x= 8 to 11)
These bits are written by software to select the source input for EXTIx external interrupt.
0000: PA[x] pin
0001: PB[x] pin
0010: PC[x] pin
0011: PD[x] pin
0100: PE[x] pin
0101: PF[x] pin
0110: PG[x] pin
7.4.6
External interrupt configuration register 4 (AFIO_EXTICR4)
Address offset: 0x14
Reset value: 0x0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
rw
rw
Reserved
15
14
13
12
11
rw
rw
EXTI15[3:0]
rw
rw
Bits 31:16
rw
10
9
8
7
rw
rw
EXTI14[3:0]
rw
rw
EXTI13[3:0]
rw
rw
EXTI12[3:0]
rw
rw
rw
Reserved
Bits 15:0 EXTIx[3:0]: EXTI x configuration (x= 12 to 15)
These bits are written by software to select the source input for EXTIx external interrupt.
0000: PA[x] pin
0001: PB[x] pin
0010: PC[x] pin
0011: PD[x] pin
0100: PE[x] pin
0101: PF[x] pin
0110: PG[x] pin
Doc ID16188 Rev 5
125/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.4.7
RM0041
AF remap and debug I/O configuration register (AFIO_MAPR2)
Address offset: 0x1C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
Reserved
15
14
Reserved
13
MISC
_
REM
AP
rw
Bits 31:14
12
11
TIM67_
TIM12_ DAC_
REMA DMA_
P
REMA
P
rw
rw
10
FSM
C_NA
DV
rw
9
8
TIM14_ TIM13_
REMA REMA
P
P
rw
7
Reserved
rw
TIM1_
DMA_
REMAP
rw
CEC_ TIM17_ TIM16_ TIM15_
REMA REMA REMA REMA
P
P
P
P
rw
rw
rw
rw
Reserved.
Bit 13 MISC_REMAP: Miscellaneous features remapping.
This bit is set and cleared by software. It controls miscellaneous features
The DMA2 channel 5 interrupt position in the vector table
The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the
DAC_CR register).
0: DMA2 channel 5 interrupt is mapped with DMA2 channel 4 at position 59, TIM5 TRGO
event is selected as DAC Trigger 3, TIM5 triggers TIM1/3.
1: DMA2 channel 5 interrupt is mapped separately at position 60 and TIM15 TRGO event is
selected as DAC Trigger 3, TIM15 triggers TIM1/3.
Note: This bit is available only in high density value line devices.
Bit 12 TIM12_REMAP: TIM12 remapping
This bit is set and cleared by software. It controls the mapping of the TIM12_CH1 and
TIM12_CH2 alternate function onto the GPIO ports.
0: No remap (CH1/PC4, CH2/PC5)
1: Remap (CH1/PB12, CH2/PB13)
Note: This bit is available only in high density value line devices.
Bit 11 TIM76_DAC_DMA_REMAP: TIM67_DAC DMA remapping
This bit is set and cleared by software. It controls the mapping of the TIM6_DAC1 and
TIM7_DAC2 DMA requests onto the DMA1 channels.
0: No remap (TIM6_DAC1 DMA request/DMA2 Channel3, TIM7_DAC2 DMA request/DMA2
Channel4)
1: Remap (TIM6_DAC1 DMA request/DMA1 Channel3, TIM7_DAC2 DMA request/DMA1
Channel4)
Bit 10 FSMC_NADV: NADV connect/disconnect
This bit is set and cleared by software. It controls the use of the optional FSMC_NADV
signal.
0: The NADV signal is connected to the output (default)
1: The NADV signal is not connected. The I/O pin can be used by another peripheral.
Note: This bit is available only in high density value line devices.
Bit 9 TIM14_REMAP: TIM14 remapping
This bit is set and cleared by software. It controls the mapping of the TIM14_CH1 alternate
function onto the GPIO ports.
0: No remap (PC9)
1: Remap (PB1)
126/713
Doc ID16188 Rev 5
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Bit 8 TIM13_REMAP: TIM13 remapping
This bit is set and cleared by software. It controls the mapping of the TIM13_CH1 alternate
function onto the GPIO ports.
0: No remap (PC8)
1: Remap (PB0)
Bits 7:5
Reserved.
Bit 4 TIM1_DMA_REMAP: TIM1 DMA remapping
This bit is set and cleared by software. It controls the mapping of the TIM1 channel 1 and
channel 2 DMA requests onto the DMA1 channels.
0: No remap (TIM1_CH1 DMA request/DMA1 Channel2, TIM1_CH2 DMA request/DMA1
Channel3)
1: Remap (TIM1_CH1 DMA request/DMA1 Channel6, TIM1_CH2 DMA request/DMA1
Channel6)
Bit 3 CEC_REMAP: CEC remapping
This bit is set and cleared by software. It controls the mapping of the alternate functions of
the CEC line onto the GPIO ports.
0: No remap (CEC/PB8)
1: Remap (CEC/PB10)
Bit 2 TIM17_REMAP: TIM17 remapping
This bit is set and cleared by software. It controls the mapping of the alternate functions of
TIM17 channel 1 onto the GPIO ports.
0: No remap (CH1/PB9)
1: Remap (CH1/PA7)
Bit 1 TIM16_REMAP: TIM16 remapping
This bit is set and cleared by software. It controls the mapping of the alternate functions of
TIM16 channel 1 onto the GPIO ports.
0: No remap (CH1/PB8)
1: Remap (CH1/PA6)
Bit 0 TIM15_REMAP: TIM15 remapping
This bit is set and cleared by software. It controls the mapping of the alternate functions of
TIM15 channels 1 and 2 onto the GPIO ports.
0: No remap (CH1/PA2, CH2/PA3)
1: Remap (CH1/PB14, CH2/PB15)
Doc ID16188 Rev 5
127/713
129
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
7.5
RM0041
GPIO and AFIO register maps
The following tables give the GPIO and AFIO register map and the reset values.
Refer to Table 1 on page 36 and Table 2 on page 37 for the register boundary addresses.
0x00
GPIOx_CRL
Reset value
0x04
GPIOx_CRH
Reset value
0x08
CN
F5
[1:0]
MOD
E5
[1:0]
CNF
4
[1:0]
MOD
E4
[1:0]
CN MODE CNF MODE CN
F3
3
2
2
F1
[1:0] [1:0] [1:0] [1:0] [1:0]
MOD
E1
[1:0]
CNF
0
[1:0]
MOD
E0
[1:0]
0 1 0 0 0 1
CN
CN
MODE
F
F
15
15
14
[1:0]
[1:0]
[1:0]
0 1 0 0 0 1
0
0 1
CN
F
13
[1:0]
0 1
0
0
0 1
0
0
0
0 1
0
MOD
E13
[1:0]
CNF
12
[1:0]
MOD
E12
[1:0]
MOD
E9
[1:0]
CNF
8
[1:0]
MOD
E8
[1:0]
0
0 1
0
0 1 0 0 0 1 0 0 0 1
CN
CN
MODE CNF MODE
F
F
11
10
10
11
9
[1:0] [1:0] [1:0]
[1:0]
[1:0]
0 1 0 0 0 1 0 0 0 1
0
0
0 1
0
0
0
0
0 0
0
0
0
0
0 0
0
0
0
0
0 0
0
0
0
0
0 0
0
0
0
0
0 0
0
0
0
MOD
E14
[1:0]
0
GPIOx_IDR
0
0
0
0
0 0
0x14
0
0 0
0
0
0 0
0
0
0 0
0
BR[15:0]
0 0
0
0
0 0
0
GPIOx_BRR
0
0 0
0
0 0
BSR[15:0]
0
0
0 0
0
0
0 0
0
0
0 0
0
0
0 0
BR[15:0]
Reserved
0
0
0 0
0
LCKK
0 0
GPIOx_LCK
R
0 0
ODRy
Reset value
0x18
0
Reserved
GPIOx_BSR
R
0
IDRy
Reserved
GPIOx_ODR
Reset value
8
7
6
5
4
3
2
1
0
MOD
E6
[1:0]
Reset value
0x10
11
10
9
CN MODE CN
F7
7
F6
[1:0] [1:0] [1:0]
Reset value
0x0C
12
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
Register
28
Offset
31
30
29
Table 48. GPIO register map and reset values
Reserved
Reset value
0
0 0
LCK[15:0]
0
0 0
0
0
0 0
0
0
0 0
128/713
0
0
0
0
0
0
I2C1_REMAP
0
0
SPI1_REMAP
0
Doc ID16188 Rev 5
0
0
0
0
0
0
0
0
0
0
TIM1_REMAP[1:0]
TIM2_REMAP[1:0]
0
TIM3_REMAP[1:0]
0
TIM4_REMAP
Reserved
Reserved
SWJ_
CFG[2:0]
PD01_REMAP
Reset value
Reserved
TIM5CH4_IREMAP
AFIO_MAPR
PIN[3:0]
USART1_REMAP
Reserved
Reset value
0x04
PORT[2:
0]
USART2_REMAP
AFIO_EVCR
0
0
0
USART3_REMAP[1:0]
0x00
Register
EVOE
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 49. AFIO register map and reset values
0
RM0041
General-purpose and alternate-function I/Os (GPIOs and AFIOs)
Reserved
0
Reset value
0x14
AFIO_EXTICR4
Reserved
Reset value
0x1C
AFIO_MAPR2
Reserved
Reset value
Doc ID16188 Rev 5
0
0
0
0
EXTI6[3:0]
0
0
0
0
EXTI11[3:0]
EXTI10[3:0]
0
0
0
0
0
0
0
0
0
0
0
0
EXTI5[3:0]
0
0
0
0
EXTI9[3:0]
0
0
0
0
0
0
0
0
EXTI4[3:0]
0
0
0
0
EXTI8[3:0]
0
0
0
0
EXTI15[3:0]
EXTI14[3:0]
EXTI13[3:0]
EXTI12[3:0]
0
0
0
0
0
0
0
TIM15_REMAP
Reserved
0
0
TIM16_REMAP
AFIO_EXTICR3
EXTI7[3:0]
0
CEC_REMAP
0x10
0
EXTI0[3:0]
TIM17_REMAP
Reset value
0
EXTI1[3:0]
TIM1_DMA_REMAP
AFIO_EXTICR2
0
0
0
0
0
0
0
0
0
0
TIM13_REMAP
0x0C
0
EXTI2[3:0]
FSMC_NADV
Reset value
EXTI3[3:0]
TIM14_REMAP
Reserved
TIM67_DAC_ DMA_ REMAP
AFIO_EXTICR1
0
0
0
MISC_ REMAP
0x08
Register
TIM12_REMAP
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 49. AFIO register map and reset values (continued)
0
0
0
0
0
0
0
Res.
0
129/713
129
Interrupts and events
8
RM0041
Interrupts and events
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This Section applies to the whole STM32F100xx family, unless otherwise specified.
8.1
Nested vectored interrupt controller (NVIC)
Features
•
60 maskable interrupt channels in high-density value line devices and 56 in low and
medium-density value line devices (not including the sixteen Cortex®-M3 interrupt
lines)
•
16 programmable priority levels (4 bits of interrupt priority are used)
•
Low-latency exception and interrupt handling
•
Power management control
•
Implementation of System Control Registers
The NVIC and the processor core interface are closely coupled, which enables low latency
interrupt processing and efficient processing of late arriving interrupts.
All interrupts including the core exceptions are managed by the NVIC. For more information
on exceptions and NVIC programming, refer to STM32F100xx Cortex®-M3 programming
manual (see Related documents on page 1).
8.1.1
SysTick calibration value register
The SysTick calibration value is set to 9000, which gives a reference time base of 3 ms with
the SysTick clock set to 3 MHz (max HCLK/8).
8.1.2
Interrupt and exception vectors
130/713
Position
Priority
Table 50. Vector table for STM32F100xx devices
Type of
priority
-
-
-
-
-3
fixed
Acronym
Description
Address
-
Reserved
0x0000_0000
Reset
Reset
0x0000_0004
Doc ID16188 Rev 5
RM0041
Interrupts and events
Position
Priority
Table 50. Vector table for STM32F100xx devices (continued)
Type of
priority
-
-2
fixed
NMI_Handler
Non maskable interrupt. The RCC
Clock Security System (CSS) is
linked to the NMI vector.
0x0000_0008
-
-1
fixed
HardFault_Handler
All class of fault
0x0000_000C
-
0
settable
MemManage_Handl
Memory management
er
0x0000_0010
-
1
settable
BusFault_Handler
Pre-fetch fault, memory access fault
0x0000_0014
-
2
settable
UsageFault_Handler Undefined instruction or illegal state
0x0000_0018
-
-
-
-
3
-
Acronym
Description
Address
-
Reserved
0x0000_001C 0x0000_002B
settable
SVC_Handler
System service call via SWI
instruction
0x0000_002C
4
settable
DebugMon_Handler Debug Monitor
0x0000_0030
-
-
-
-
Reserved
0x0000_0034
-
5
settable
PendSV_Handler
Pendable request for system
service
0x0000_0038
-
6
settable
SysTick_Handler
System tick timer
0x0000_003C
0
7
settable
WWDG
Window Watchdog interrupt
0x0000_0040
1
8
settable
PVD
PVD through EXTI Line detection
interrupt
0x0000_0044
2
9
settable
TAMPER_STAMP
Tamper and TimeStamp through
EXTI line interrupts
0x0000_0048
3
10
settable
RTC_WKUP
RTC Wakeup through EXTI line
interrupt
0x0000_004C
4
11
settable
FLASH
Flash global interrupt
0x0000_0050
5
12
settable
RCC
RCC global interrupt
0x0000_0054
6
13
settable
EXTI0
EXTI Line0 interrupt
0x0000_0058
7
14
settable
EXTI1
EXTI Line1 interrupt
0x0000_005C
8
15
settable
EXTI2
EXTI Line2 interrupt
0x0000_0060
9
16
settable
EXTI3
EXTI Line3 interrupt
0x0000_0064
10
17
settable
EXTI4
EXTI Line4 interrupt
0x0000_0068
11
18
settable
DMA1_Channel1
DMA1 Channel1 global interrupt
0x0000_006C
12
19
settable
DMA1_Channel2
DMA1 Channel2 global interrupt
0x0000_0070
Doc ID16188 Rev 5
131/713
141
Interrupts and events
RM0041
Position
Priority
Table 50. Vector table for STM32F100xx devices (continued)
Type of
priority
13
20
settable
DMA1_Channel3
DMA1 Channel3 global interrupt
0x0000_0074
14
21
settable
DMA1_Channel4
DMA1 Channel4 global interrupt
0x0000_0078
15
22
settable
DMA1_Channel5
DMA1 Channel5 global interrupt
0x0000_007C
16
23
settable
DMA1_Channel6
DMA1 Channel6 global interrupt
0x0000_0080
17
24
settable
DMA1_Channel7
DMA1 Channel7 global interrupt
0x0000_0084
18
25
settable
ADC1
ADC1 global interrupt
0x0000_0088
-
-
-
-
Reserved
0x0000_008C 0x0000_0098
23
30
settable
EXTI9_5
EXTI Line[9:5] interrupts
0x0000_009C
24
31
settable
TIM1_BRK_TIM15
TIM1 Break and TIM15 global
interrupt
0x0000_00A0
25
32
settable
TIM1_UP_TIM16
TIM1 Update and TIM16 global
interrupts
0x0000_00A4
26
33
settable
TIM1_TRG_COM_T TIM1 Trigger and Commutation and
IM17
TIM17 global interrupts
0x0000_00A8
27
34
settable
TIM1_CC
TIM1 Capture Compare interrupt
0x0000_00AC
28
35
settable
TIM2
TIM2 global interrupt
0x0000_00B0
29
36
settable
TIM3
TIM3 global interrupt
0x0000_00B4
30
37
settable
TIM4
TIM4 global interrupt
0x0000_00B8
31
38
settable
I2C1_EV
I2C1 event interrupt
0x0000_00BC
32
33
132/713
39
40
settable
settable
Acronym
Description
Address
I2C1_ER
2C1
I
error interrupt
0x0000_00C0
I2C2_EV
I2C2
event interrupt
0x0000_00C4
2
34
41
settable
I2C2_ER
I C2 error interrupt
0x0000_00C8
35
42
settable
SPI1
SPI1 global interrupt
0x0000_00CC
36
43
settable
SPI2
SPI2 global interrupt
0x0000_00D0
37
44
settable
USART1
USART1 global interrupt
0x0000_00D4
38
45
settable
USART2
USART2 global interrupt
0x0000_00D8
39
46
settable
USART3
USART3 global interrupt
0x0000_00DC
40
47
settable
EXTI15_10
EXTI Line[15:10] interrupts
0x0000_00E0
41
48
settable
RTC_Alarm
RTC Alarms (A and B) through EXTI
line interrupt
0x0000_00E4
42
49
settable
CEC
CEC global interrupt
0x0000_00E8
Doc ID16188 Rev 5
RM0041
Interrupts and events
Position
Priority
Table 50. Vector table for STM32F100xx devices (continued)
Type of
priority
43
50
settable
TIM12
TIM12 global interrupt
0x0000_00EC
44
51
settable
TIM13
TIM13 global interrupt
0x0000_00F0
45
52
settable
TIM14
TIM14 global interrupt
0x0000_00F4
-
-
-
-
Reserved
0x0000_00F8 0x0000_00FC
48
55
settable
FSMC
FSMC global interrupt
0x0000_0100
-
-
-
-
Reserved
0x0000_0104
50
57
settable
TIM5
TIM5 global interrupt
0x0000_0108
51
58
settable
SPI3
SPI3 global interrupt
0x0000_010C
52
59
settable
UART4
UART4 global interrupt
0x0000_0110
53
60
settable
UART5
UART5 global interrupt
0x0000_0114
54
61
settable
TIM6_DAC
TIM6 global and DAC underrun
interrupts
0x0000_0118
55
62
settable
TIM7
TIM7 global interrupt
0x0000_011C
56
63
settable
DMA2_Channel1
DMA2 Channel1 global interrupt
0x0000_0120
57
64
settable
DMA2_Channel2
DMA2 Channel2 global interrupt
0x0000_0124
58
65
settable
DMA2_Channel3
DMA2 Channel3 global interrupt
0x0000_0128
59
66
settable
DMA2_Channel4_5
DMA2 Channel4 and DMA2
Channel5 global interrupts
0x0000_012C
60
67
settable
DMA2_Channel5(1)
DMA2 Channel5 global interrupt
0x0000_0130
Acronym
Description
Address
1. For High-density value line devices, the DMA2 Channel 5 is mapped at postion 60 only if the
MISC_REMAP bit in the AFIO_MAPR2 register is set and DMA2 Channel 2 is connected with DMA2
Channel 4 at position 59 when the MISC_REMAP bit in the AFIO_MAPR2 register is reset.
Doc ID16188 Rev 5
133/713
141
Interrupts and events
8.2
RM0041
External interrupt/event controller (EXTI)
The external interrupt/event controller consists of up to 18 edge detectors for generating
event/interrupt requests. Each input line can be independently configured to select the type
(event or interrupt) and the corresponding trigger event (rising or falling or both). Each line
can also masked independently. A pending register maintains the status line of the interrupt
requests
8.2.1
Main features
The EXTI controller main features are the following:
8.2.2
•
Independent trigger and mask on each interrupt/event line
•
Dedicated status bit for each interrupt line
•
Generation of up to 18 software event/interrupt requests
•
Detection of external signal with pulse width lower than APB2 clock period. Refer to the
electrical characteristics section of the datasheet for details on this parameter.
Block diagram
The block diagram is shown in Figure 18.
Figure 18. External interrupt/event controller block diagram
!-"! !0"BUS
0#,+
0ERIPHERALINTERFACE
0ENDING
REQUEST
REGISTER
)NTERRUPT
MASK
REGISTER
3OFTWARE
INTERRUPT
EVENT
REGISTER
4O.6)#INTERRUPT
CONTROLLER
2ISING
TRIGGER
SELECTION
REGISTER
&ALLING
TRIGGER
SELECTION
REGISTER
0ULSE
GENERATOR
%DGEDETECT
CIRCUIT
)NPUT
,INE
(YHQW
PDVN
UHJLVWHU
-36
134/713
Doc ID16188 Rev 5
RM0041
8.2.3
Interrupts and events
Wakeup event management
The STM32F100xx is able to handle external or internal events in order to wake up the core
(WFE). The wakeup event can be generated either by:
•
enabling an interrupt in the peripheral control register but not in the NVIC, and enabling
the SEVONPEND bit in the Cortex®-M3 System Control register. When the MCU
resumes from WFE, the peripheral interrupt pending bit and the peripheral NVIC IRQ
channel pending bit (in the NVIC interrupt clear pending register) have to be cleared.
•
or configuring an external or internal EXTI line in event mode. When the CPU resumes
from WFE, it is not necessary to clear the peripheral interrupt pending bit or the NVIC
IRQ channel pending bit as the pending bit corresponding to the event line is not set.
To use an external line as a wakeup event, refer to Section 8.2.4: Functional description.
8.2.4
Functional description
To generate the interrupt, the interrupt line should be configured and enabled. This is done
by programming the two trigger registers with the desired edge detection and by enabling
the interrupt request by writing a ‘1’ to the corresponding bit in the interrupt mask register.
When the selected edge occurs on the external interrupt line, an interrupt request is
generated. The pending bit corresponding to the interrupt line is also set. This request is
reset by writing a ‘1’ in the pending register.
To generate the event, the event line should be configured and enabled. This is done by
programming the two trigger registers with the desired edge detection and by enabling the
event request by writing a ‘1’ to the corresponding bit in the event mask register. When the
selected edge occurs on the event line, an event pulse is generated. The pending bit
corresponding to the event line is not set
An interrupt/event request can also be generated by software by writing a ‘1’ in the software
interrupt/event register.
Hardware interrupt selection
To configure the 18 lines as interrupt sources, use the following procedure:
•
Configure the mask bits of the 18 Interrupt lines (EXTI_IMR)
•
Configure the Trigger Selection bits of the Interrupt lines (EXTI_RTSR and
EXTI_FTSR)
•
Configure the enable and mask bits that control the NVIC IRQ channel mapped to the
External Interrupt Controller (EXTI) so that an interrupt coming from one of the 18 lines
can be correctly acknowledged.
Hardware event selection
To configure the 18 lines as event sources, use the following procedure:
•
Configure the mask bits of the 18 Event lines (EXTI_EMR)
•
Configure the Trigger Selection bits of the Event lines (EXTI_RTSR and EXTI_FTSR)
Doc ID16188 Rev 5
135/713
141
Interrupts and events
RM0041
Software interrupt/event selection
The 18 lines can be configured as software interrupt/event lines. The following is the
procedure to generate a software interrupt.
8.2.5
•
Configure the mask bits of the 18 Interrupt/Event lines (EXTI_IMR, EXTI_EMR)
•
Set the required bit of the software interrupt register (EXTI_SWIER)
External interrupt/event line mapping
The 112 GPIOs are connected to the 16 external interrupt/event lines in the following
manner:
136/713
Doc ID16188 Rev 5
RM0041
Interrupts and events
Figure 19. External interrupt/event GPIO mapping
EXTI0[3:0] bits in AFIO_EXTICR1 register
PA0
PB0
PC0
EXTI0
PD0
PE0
PF0
PG0
EXTI1[3:0] bits in AFIO_EXTICR1 register
PA1
PB1
PC1
EXTI1
PD1
PE1
PF1
PG1
EXTI15[3:0] bits in AFIO_EXTICR4 register
PA15
PB15
PC15
EXTI15
PD15
PE15
PF15
PG15
1. To configure the AFIO_EXTICRx for the mapping of external interrupt/event lines onto GPIOs, the AFIO
clock should first be enabled. Refer to Section 6.3.7: APB2 peripheral clock enable register
(RCC_APB2ENR).
The two other EXTI lines are connected as follows:
•
EXTI line 16 is connected to the PVD output
•
EXTI line 17 is connected to the RTC Alarm event
Doc ID16188 Rev 5
137/713
141
Interrupts and events
8.3
RM0041
EXTI registers
Refer to Section 1.1 on page 32 for a list of abbreviations used in register descriptions.
The peripheral registers have to be accessed by words (32-bit).
8.3.1
Interrupt mask register (EXTI_IMR)
Address offset: 0x00
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
Reserved
17
16
MR17
MR16
rw
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
MR15
MR14
MR13
MR12
MR11
MR10
MR9
MR8
MR7
MR6
MR5
MR4
MR3
MR2
MR1
MR0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
21
20
19
18
Bits 31:18 Reserved, must be kept at reset value (0).
Bits 17:0 MRx: Interrupt Mask on line x
0: Interrupt request from Line x is masked
1: Interrupt request from Line x is not masked
8.3.2
Event mask register (EXTI_EMR)
Address offset: 0x04
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
Reserved
17
16
MR17
MR16
rw
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
MR15
MR14
MR13
MR12
MR11
MR10
MR9
MR8
MR7
MR6
MR5
MR4
MR3
MR2
MR1
MR0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 31:18 Reserved, must be kept at reset value (0).
Bits 17:0 MRx: Event mask on line x
0: Event request from Line x is masked
1: Event request from Line x is not masked
138/713
Doc ID16188 Rev 5
RM0041
Interrupts and events
8.3.3
Rising trigger selection register (EXTI_RTSR)
Address offset: 0x08
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
Reserved
17
16
TR17
TR16
rw
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
TR15
TR14
TR13
TR12
TR11
TR10
TR9
TR8
TR7
TR6
TR5
TR4
TR3
TR2
TR1
TR0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 31:18
Reserved, must be kept at reset value (0).
Bits 17:0 TRx: Rising trigger event configuration bit of line x
0: Rising trigger disabled (for Event and Interrupt) for input line
1: Rising trigger enabled (for Event and Interrupt) for input line
Note:
The external wakeup lines are edge triggered, no glitches must be generated on these lines.
If a rising edge on external interrupt line occurs during writing of EXTI_RTSR register, the
pending bit will not be set.
Rising and Falling edge triggers can be set for the same interrupt line. In this configuration,
both generate a trigger condition.
8.3.4
Falling trigger selection register (EXTI_FTSR)
Address offset: 0x0C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
Reserved
17
16
TR17
TR16
rw
rw
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
TR15
TR14
TR13
TR12
TR11
TR10
TR9
TR8
TR7
TR6
TR5
TR4
TR3
TR2
TR1
TR0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 31:18
Reserved, must be kept at reset value (0).
Bits 17:0 TRx: Falling trigger event configuration bit of line x
0: Falling trigger disabled (for Event and Interrupt) for input line
1: Falling trigger enabled (for Event and Interrupt) for input line
Note:
The external wakeup lines are edge triggered, no glitches must be generated on these lines.
If a falling edge on external interrupt line occurs during writing of EXTI_FTSR register, the
pending bit will not be set.
Rising and Falling edge triggers can be set for the same interrupt line. In this configuration,
both generate a trigger condition.
Doc ID16188 Rev 5
139/713
141
Interrupts and events
8.3.5
RM0041
Software interrupt event register (EXTI_SWIER)
Address offset: 0x10
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
Reserved
15
14
13
12
11
10
9
8
SWIER SWIER SWIER SWIER SWIER SWIER SWIER
15
14
13
12
11
10
9
rw
rw
rw
Bits 31:18
rw
rw
rw
rw
17
16
SWIER SWIER
17
16
7
6
5
4
3
2
rw
rw
1
0
SWIER SWIER SWIER SWIER SWIER SWIER SWIER SWIER SWIER
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
rw
Reserved, must be kept at reset value (0).
Bits 17:0 SWIERx: Software interrupt on line x
If the interrupt is enabled on this line in the EXTI_IMR, writing a '1' to this bit when it is at '0'
sets the corresponding pending bit in EXTI_PR resulting in an interrupt request generation.
This bit is cleared by clearing the corresponding bit of EXTI_PR (by writing a 1 into the bit)
8.3.6
Pending register (EXTI_PR)
Address offset: 0x14
Reset value: undefined
31
30
29
28
27
26
25
24
23
22
21
20
19
18
Reserved
17
16
PR17
PR16
rc_w1
rc_w1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PR15
PR14
PR13
PR12
PR11
PR10
PR9
PR8
PR7
PR6
PR5
PR4
PR3
PR2
PR1
PR0
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
rc_w1
Bits 31:18
Reserved, must be kept at reset value (0).
Bits 17:0 PRx: Pending bit
0: No trigger request occurred
1: selected trigger request occurred
This bit is set when the selected edge event arrives on the external interrupt line. This bit is
cleared by writing a ‘1’ into the bit.
140/713
Doc ID16188 Rev 5
RM0041
8.3.7
Interrupts and events
EXTI register map
The following table gives the EXTI register map and the reset values.
Offset
0x00
Register
EXTI_IMR
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 51. External interrupt/event controller register map and reset values
Reset value
0x04
EXTI_EMR
0
EXTI_RTSR
EXTI_FTSR
EXTI_SWIER
EXTI_PR
Reset value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
RTSR[17:0]
0
0
0
0
0
0
0
0
0
0
0
FTSR[17:0]
Reserved
0
0
0
0
0
0
0
0
0
0
0
SWIER[17:0]
Reserved
Reset value
0x14
0
Reserved
Reset value
0x10
0
EMR[17:0]
0
Reset value
0x0C
0
Reserved
Reset value
0x08
MR[17:0]
Reserved
0
0
0
0
0
0
0
0
0
0
0
PR[17:0]
Reserved
0
0
0
0
0
0
0
0
0
0
0
Refer to Table 1 on page 36 and Table 2 on page 37 for the register boundary addresses.
Doc ID16188 Rev 5
141/713
141
Direct memory access controller (DMA)
9
RM0041
Direct memory access controller (DMA)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
9.1
DMA introduction
Direct memory access (DMA) is used in order to provide high-speed data transfer between
peripherals and memory as well as memory to memory. Data can be quickly moved by DMA
without any CPU actions. This keeps CPU resources free for other operations.
The two DMA controllers have 12 channels in total (7 for DMA1 and 5 for DMA2), each
dedicated to managing memory access requests from one or more peripherals. It has an
arbiter for handling the priority between DMA requests.
9.2
DMA main features
•
12 independently configurable channels (requests): 7 for DMA1 and 5 for DMA2
•
Each of the 12 channels is connected to dedicated hardware DMA requests, software
trigger is also supported on each channel. This configuration is done by software.
•
Priorities between requests from channels of one DMA are software programmable (4
levels consisting of very high, high, medium, low) or hardware in case of equality
(request 1 has priority over request 2, etc.)
•
Independent source and destination transfer size (byte, half word, word), emulating
packing and unpacking. Source/destination addresses must be aligned on the data
size.
•
Support for circular buffer management
•
3 event flags (DMA Half Transfer, DMA Transfer complete and DMA Transfer Error)
logically ORed together in a single interrupt request for each channel
•
Memory-to-memory transfer
•
Peripheral-to-memory and memory-to-peripheral, and peripheral-to-peripheral
transfers
•
Access to Flash, SRAM, APB1, APB2 and AHB peripherals as source and destination
•
Programmable number of data to be transferred: up to 65536
The block diagram is shown in Figure 20 and Figure 21.
142/713
Doc ID16188 Rev 5
RM0041
Direct memory access controller (DMA)
Figure 20. DMA block diagram in low and medium- density
Cat.1 and Cat.2 STM32F100xx devices
)#ODE
&,!3(
&LASH
INTERFACE
$#ODE
&LASH
MEMORY
#ORTEX-
#H
#H
$-!
"USMATRIX
32!$-!
2ESETCLOCK
#2#
CONTROL2##
"RIDGE
#H
"RIDGE
!RBITER
!0"
4)-
4)-
4)-
!$#
53!24
30)
4)-
!("3LAVE
!0"
$!#
)#
)#
53!24
53!24
30)
4)-
4)-
4)-
4)-
4)-
AI
Doc ID16188 Rev 5
143/713
159
Direct memory access controller (DMA)
RM0041
Figure 21. DMA block diagram in high-density
Cat.4 and Cat.5 STM32F100xx devices
ICode
Flash
FLITF
DCode
Cortex-M3
Sys tem
DMA1
Ch.1
DMA
Ch.2
Bus matrix
SRAM
FSMC
AHB System
Ch.7
Bridge 2
Bridge 1
DMA
Arbiter
DMA request
DMA request
AHB Slave
DMA2
Ch.1
DMA request
Ch.2
APB2
APB1
ADC1
USART1
SPI1
TI M1
TIM17
TIM16
TIM15
DAC
I2C2
I2C1
UART5
UART4
USART3
USART2
SPI2
SPI3
TIM7
TIM6
TIM5
TIM4
TIM3
TIM2
Ch.5
DMA request
Arbiter
AHB Slave
Reset & clock control
(RCC)
Note:
ai18303
The DMA2 controller and its related requests are available only in High density value line
devices.
SPI3, UART4, UART5and TIM5 DMA requests are available only in High density value line
devices.
9.3
DMA functional description
The DMA controller performs direct memory transfer by sharing the system bus with the
Cortex®-M3 core. The DMA request may stop the CPU access to the system bus for some
bus cycles, when the CPU and DMA are targeting the same destination (memory or
peripheral). The bus matrix implements round-robin scheduling, thus ensuring at least half
of the system bus bandwidth (both to memory and peripheral) for the CPU.
9.3.1
DMA transactions
After an event, the peripheral sends a request signal to the DMA Controller. The DMA
controller serves the request depending on the channel priorities. As soon as the DMA
Controller accesses the peripheral, an Acknowledge is sent to the peripheral by the DMA
Controller. The peripheral releases its request as soon as it gets the Acknowledge from the
144/713
Doc ID16188 Rev 5
RM0041
Direct memory access controller (DMA)
DMA Controller. Once the request is deasserted by the peripheral, the DMA Controller
release the Acknowledge. If there are more requests, the peripheral can initiate the next
transaction.
In summary, each DMA transfer consists of three operations:
9.3.2
•
The loading of data from the peripheral data register or a location in memory addressed
through an internal current peripheral/memory address register. The start address used
for the first transfer is the base peripheral/memory address programmed in the
DMA_CPARx or DMA_CMARx register
•
The storage of the data loaded to the peripheral data register or a location in memory
addressed through an internal current peripheral/memory address register. The start
address used for the first transfer is the base peripheral/memory address programmed
in the DMA_CPARx or DMA_CMARx register
•
The post-decrementing of the DMA_CNDTRx register, which contains the number of
transactions that have still to be performed.
Arbiter
The arbiter manages the channel requests based on their priority and launches the
peripheral/memory access sequences.
The priorities are managed in two stages:
•
Software: each channel priority can be configured in the DMA_CCRx register. There
are four levels:
–
•
Very high priority
–
High priority
–
Medium priority
–
Low priority
Hardware: if 2 requests have the same software priority level, the channel with the
lowest number will get priority versus the channel with the highest number. For
example, channel 2 gets priority over channel 4.
Note:
In high-density value line devices, the DMA1 controller has priority over the DMA2
controller.
9.3.3
DMA channels
Each channel can handle DMA transfer between a peripheral register located at a fixed
address and a memory address. The amount of data to be transferred (up to 65535) is
programmable. The register which contains the amount of data items to be transferred is
decremented after each transaction.
Programmable data sizes
Transfer data sizes of the peripheral and memory are fully programmable through the
PSIZE and MSIZE bits in the DMA_CCRx register.
Pointer incrementation
Peripheral and memory pointers can optionally be automatically post-incremented after
each transaction depending on the PINC and MINC bits in the DMA_CCRx register. If
incremented mode is enabled, the address of the next transfer will be the address of the
previous one incremented by 1, 2 or 4 depending on the chosen data size. The first transfer
Doc ID16188 Rev 5
145/713
159
Direct memory access controller (DMA)
RM0041
address is the one programmed in the DMA_CPARx/DMA_CMARx registers. During
transfer operations, these registers keep the initially programmed value. The current
transfer addresses (in the current internal peripheral/memory address register) are not
accessible by software.
If the channel is configured in noncircular mode, no DMA request is served after the last
transfer (that is once the number of data items to be transferred has reached zero). In order
to reload a new number of data items to be transferred into the DMA_CNDTRx register, the
DMA channel must be disabled.
Note:
If a DMA channel is disabled, the DMA registers are not reset. The DMA channel registers
(DMA_CCRx, DMA_CPARx and DMA_CMARx) retain the initial values programmed during
the channel configuration phase.
In circular mode, after the last transfer, the DMA_CNDTRx register is automatically reloaded
with the initially programmed value. The current internal address registers are reloaded with
the base address values from the DMA_CPARx/DMA_CMARx registers.
Channel configuration procedure
The following sequence should be followed to configure a DMA channelx (where x is the
channel number).
1.
Set the peripheral register address in the DMA_CPARx register. The data will be
moved from/ to this address to/ from the memory after the peripheral event.
2.
Set the memory address in the DMA_CMARx register. The data will be written to or
read from this memory after the peripheral event.
3.
Configure the total number of data to be transferred in the DMA_CNDTRx register.
After each peripheral event, this value will be decremented.
4.
Configure the channel priority using the PL[1:0] bits in the DMA_CCRx register
5.
Configure data transfer direction, circular mode, peripheral & memory incremented
mode, peripheral & memory data size, and interrupt after half and/or full transfer in the
DMA_CCRx register
6.
Activate the channel by setting the ENABLE bit in the DMA_CCRx register.
As soon as the channel is enabled, it can serve any DMA request from the peripheral
connected on the channel.
Once half of the bytes are transferred, the half-transfer flag (HTIF) is set and an interrupt is
generated if the Half-Transfer Interrupt Enable bit (HTIE) is set. At the end of the transfer,
the Transfer Complete Flag (TCIF) is set and an interrupt is generated if the Transfer
Complete Interrupt Enable bit (TCIE) is set.
Circular mode
Circular mode is available to handle circular buffers and continuous data flows (e.g. ADC
scan mode). This feature can be enabled using the CIRC bit in the DMA_CCRx register.
When circular mode is activated, the number of data to be transferred is automatically
reloaded with the initial value programmed during the channel configuration phase, and the
DMA requests continue to be served.
Memory-to-memory mode
The DMA channels can also work without being triggered by a request from a peripheral.
This mode is called Memory to Memory mode.
146/713
Doc ID16188 Rev 5
RM0041
Direct memory access controller (DMA)
If the MEM2MEM bit in the DMA_CCRx register is set, then the channel initiates transfers
as soon as it is enabled by software by setting the Enable bit (EN) in the DMA_CCRx
register. The transfer stops once the DMA_CNDTRx register reaches zero. Memory to
Memory mode may not be used at the same time as Circular mode.
9.3.4
Programmable data width, data alignment and endians
When PSIZE and MSIZE are not equal, the DMA performs some data alignments as
described in Table 52.
Table 52. Programmable data width & endian behavior (when bits PINC = MINC = 1)
Source
port
width
Destination
port
width
Number
of data
items to
transfer
(NDT)
8
8
4
@0x0 / B0
@0x1 / B1
@0x2 / B2
@0x3 / B3
1: READ B0[7:0] @0x0 then WRITE B0[7:0] @0x0
2: READ B1[7:0] @0x1 then WRITE B1[7:0] @0x1
3: READ B2[7:0] @0x2 then WRITE B2[7:0] @0x2
4: READ B3[7:0] @0x3 then WRITE B3[7:0] @0x3
@0x0 / B0
@0x1 / B1
@0x2 / B2
@0x3 / B3
8
16
4
@0x0 / B0
@0x1 / B1
@0x2 / B2
@0x3 / B3
1: READ B0[7:0] @0x0 then WRITE 00B0[15:0] @0x0
2: READ B1[7:0] @0x1 then WRITE 00B1[15:0] @0x2
3: READ B3[7:0] @0x2 then WRITE 00B2[15:0] @0x4
4: READ B4[7:0] @0x3 then WRITE 00B3[15:0] @0x6
@0x0 / 00B0
@0x2 / 00B1
@0x4 / 00B2
@0x6 / 00B3
8
32
4
@0x0 / B0
@0x1 / B1
@0x2 / B2
@0x3 / B3
1: READ B0[7:0] @0x0 then WRITE 000000B0[31:0] @0x0
2: READ B1[7:0] @0x1 then WRITE 000000B1[31:0] @0x4
3: READ B3[7:0] @0x2 then WRITE 000000B2[31:0] @0x8
4: READ B4[7:0] @0x3 then WRITE 000000B3[31:0] @0xC
@0x0 / 000000B0
@0x4 / 000000B1
@0x8 / 000000B2
@0xC / 000000B3
16
8
4
@0x0 / B1B0
@0x2 / B3B2
@0x4 / B5B4
@0x6 / B7B6
1: READ B1B0[15:0] @0x0 then WRITE B0[7:0] @0x0
2: READ B3B2[15:0] @0x2 then WRITE B2[7:0] @0x1
3: READ B5B4[15:0] @0x4 then WRITE B4[7:0] @0x2
4: READ B7B6[15:0] @0x6 then WRITE B6[7:0] @0x3
@0x0 / B0
@0x1 / B2
@0x2 / B4
@0x3 / B6
16
16
4
@0x0 / B1B0
@0x2 / B3B2
@0x4 / B5B4
@0x6 / B7B6
1: READ B1B0[15:0] @0x0 then WRITE B1B0[15:0] @0x0
2: READ B3B2[15:0] @0x2 then WRITE B3B2[15:0] @0x2
3: READ B5B4[15:0] @0x4 then WRITE B5B4[15:0] @0x4
4: READ B7B6[15:0] @0x6 then WRITE B7B6[15:0] @0x6
@0x0 / B1B0
@0x2 / B3B2
@0x4 / B5B4
@0x6 / B7B6
16
32
4
@0x0 / B1B0
@0x2 / B3B2
@0x4 / B5B4
@0x6 / B7B6
1: READ B1B0[15:0] @0x0 then WRITE 0000B1B0[31:0] @0x0
2: READ B3B2[15:0] @0x2 then WRITE 0000B3B2[31:0] @0x4
3: READ B5B4[15:0] @0x4 then WRITE 0000B5B4[31:0] @0x8
4: READ B7B6[15:0] @0x6 then WRITE 0000B7B6[31:0] @0xC
@0x0 / 0000B1B0
@0x4 / 0000B3B2
@0x8 / 0000B5B4
@0xC / 0000B7B6
32
8
4
@0x0 / B3B2B1B0
@0x4 / B7B6B5B4
@0x8 / BBBAB9B8
@0xC / BFBEBDBC
1: READ B3B2B1B0[31:0] @0x0 then WRITE B0[7:0] @0x0
2: READ B7B6B5B4[31:0] @0x4 then WRITE B4[7:0] @0x1
3: READ BBBAB9B8[31:0] @0x8 then WRITE B8[7:0] @0x2
4: READ BFBEBDBC[31:0] @0xC then WRITE BC[7:0] @0x3
@0x0 / B0
@0x1 / B4
@0x2 / B8
@0x3 / BC
32
16
4
@0x0 / B3B2B1B0
@0x4 / B7B6B5B4
@0x8 / BBBAB9B8
@0xC / BFBEBDBC
1: READ B3B2B1B0[31:0] @0x0 then WRITE B1B0[7:0] @0x0
2: READ B7B6B5B4[31:0] @0x4 then WRITE B5B4[7:0] @0x1
3: READ BBBAB9B8[31:0] @0x8 then WRITE B9B8[7:0] @0x2
4: READ BFBEBDBC[31:0] @0xC then WRITE BDBC[7:0] @0x3
@0x0 / B1B0
@0x2 / B5B4
@0x4 / B9B8
@0x6 / BDBC
32
32
4
@0x0 / B3B2B1B0
@0x4 / B7B6B5B4
@0x8 / BBBAB9B8
@0xC / BFBEBDBC
1: READ B3B2B1B0[31:0] @0x0 then WRITE B3B2B1B0[31:0] @0x0
2: READ B7B6B5B4[31:0] @0x4 then WRITE B7B6B5B4[31:0] @0x4
3: READ BBBAB9B8[31:0] @0x8 then WRITE BBBAB9B8[31:0] @0x8
4: READ BFBEBDBC[31:0] @0xC then WRITE BFBEBDBC[31:0] @0xC
@0x0 / B3B2B1B0
@0x4 / B7B6B5B4
@0x8 / BBBAB9B8
@0xC / BFBEBDBC
Source content:
address / data
Transfer operations
Destination content:
address / data
Addressing an AHB peripheral that does not support byte or halfword write
operations
When the DMA initiates an AHB byte or halfword write operation, the data are duplicated on
the unused lanes of the HWDATA[31:0] bus. So when the used AHB slave peripheral does
not support byte or halfword write operations (when HSIZE is not used by the peripheral)
Doc ID16188 Rev 5
147/713
159
Direct memory access controller (DMA)
RM0041
and does not generate any error, the DMA writes the 32 HWDATA bits as shown in the two
examples below:
•
To write the halfword “0xABCD”, the DMA sets the HWDATA bus to “0xABCDABCD”
with HSIZE = HalfWord
•
To write the byte “0xAB”, the DMA sets the HWDATA bus to “0xABABABAB” with
HSIZE = Byte
Assuming that the AHB/APB bridge is an AHB 32-bit slave peripheral that does not take the
HSIZE data into account, it will transform any AHB byte or halfword operation into a 32-bit
APB operation in the following manner:
•
an AHB byte write operation of the data “0xB0” to 0x0 (or to 0x1, 0x2 or 0x3) will be
converted to an APB word write operation of the data “0xB0B0B0B0” to 0x0
•
an AHB halfword write operation of the data “0xB1B0” to 0x0 (or to 0x2) will be
converted to an APB word write operation of the data “0xB1B0B1B0” to 0x0
For instance, to write the APB backup registers (16-bit registers aligned to a 32-bit address
boundary), the memory source size (MSIZE) must be configured to “16-bit” and the
peripheral destination size (PSIZE) to “32-bit”.
9.3.5
Error management
A DMA transfer error can be generated by reading from or writing to a reserved address
space. When a DMA transfer error occurs during a DMA read or a write access, the faulty
channel is automatically disabled through a hardware clear of its EN bit in the corresponding
Channel configuration register (DMA_CCRx). The channel's transfer error interrupt flag
(TEIF) in the DMA_IFR register is set and an interrupt is generated if the transfer error
interrupt enable bit (TEIE) in the DMA_CCRx register is set.
9.3.6
Interrupts
An interrupt can be produced on a Half-transfer, Transfer complete or Transfer error for
each DMA channel. Separate interrupt enable bits are available for flexibility.
Table 53. DMA interrupt requests
Interrupt event
Event flag
Enable Control bit
Half-transfer
HTIF
HTIE
Transfer complete
TCIF
TCIE
Transfer error
TEIF
TEIE
Note:
In high-density value line devices, DMA2 Channel4 and DMA2 Channel5 interrupts are
mapped onto the same interrupt vector. All other DMA1 and DMA2 Channel interrupts have
their own interrupt vector.
9.3.7
DMA request mapping
DMA1 controller
The 7 requests from the peripherals (TIMx[1,2,3,4,6,7,15,16,17], ADC1, SPI[1,2], I2Cx[1,2],
USARTx[1,2,3]) and DAC Channelx[1,2] are simply logically ORed before entering the
DMA1, this means that only one request must be enabled at a time. Refer to Figure 22.
148/713
Doc ID16188 Rev 5
RM0041
Direct memory access controller (DMA)
The peripheral DMA requests can be independently activated/de-activated by programming
the DMA control bit in the registers of the corresponding peripheral.
Figure 22. DMA1 request mapping
Fixed hardware priority
Peripheral
request signals
ADC1
TIM2_CH3
TIM4_CH1
HW request 1
High priority
Channel 1
SW trigger (MEM2MEM bit)
Channel 1 EN bit
USART3_TX
TIM1_CH1
TIM2_UP
TIM3_CH3
SPI1_RX
TIM1_CH1(1)
USART3_RX
TIM3_CH4
TIM3_UP
TIM1_CH2(1)
SPI1_TX
TIM6_UP/DAC_Channel1(3)
USART1_TX
TIM4_CH2
SPI2_RX
I2C2_TX
TIM1_CH4
TIM1_TRIG
TIM1_COM
TIM7_UP/DAC_Channel2(3)
USART1_RX
SPI2_TX
TIM2_CH1
TIM4_CH3
I2C2_RX
TIM1_UP
TIM15_CH1
TIM15_UP
TIM15_TRIG
TIM15_COM
USART2_RX
TIM3_CH1
TIM3_TRIG
I2C1_TX
TIM1_CH3
TIM1_CH1(2)
TIM1_CH2(2)
TIM16_UP
TIM16_CH1
USART2_TX
TIM2_CH2
TIM2_CH4
TIM4_UP
I2C1_RX
TIM17_UP
TIM17_CH1
HW request 2
Channel 2
SW trigger (MEM2MEM bit)
Channel 2 EN bit
HW request 3
Channel 3
SW trigger (MEM2MEM bit)
internal
Channel 3 EN bit
DMA1
HW request 4
request
Channel 4
SW trigger (MEM2MEM bit)
Channel 4 EN bit
HW request 5
Channel 5
SW trigger (MEM2MEM bit)
Channel 5 EN bit
HW REQUEST 6
Channel 6
SW TRIGGER (MEM2MEM bit)
Channel 6 EN bit
HW request 7
Channel 7
Low priority
SW trigger (MEM2MEM bit)
Channel 7 EN bit
1. The TIM1_CH1 and TIM1_CH2 DMA requests are mapped on DMA Channel 2 and DMA Channel 3,
respectively, only if the TIM1_DMA_REMAP bit in the AFIO_MAPR2 register is cleared. For more details
refer to the AFIO section.
2. The TIM1_CH1 and TIM1_CH2 DMA requests are mapped on DMA Channel 6 only if the
TIM1_DMA_REMAP bit in the AFIO_MAPR2 register is set. For more details refer to the AFIO section.
3. For High-density value line devices, the TIM6_DAC1 and TIM7_DAC2 DMA requests are mapped
respectively on DMA1 Channel 3 and DMA1 Channel 4 only if the TIM67_DAC_DMA_REMAP bit in the
AFIO_MAPR2 register is set and mapped respectively on DMA2 Channel 3 and DMA2 Channel 4 when the
TIM67_DAC_DMA_REMAP bit in the AFIO_MAPR2 register is reset.
Doc ID16188 Rev 5
149/713
159
Direct memory access controller (DMA)
RM0041
On low- and medium -density devices the TIM6_DAC1 and TIM7_DAC2 DMA requests are always
mapped respectively on DMA1 Channel 3 and DMA1 Channel 4. For more details refer to the AFIO
section.
Table 54 lists the DMA requests for each channel.
Table 54. Summary of DMA1 requests for each channel
Peripherals Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
ADC1
ADC1
-
-
-
-
-
-
SPI
-
SPI1_RX
SPI1_TX
SPI2_RX
SPI2_TX
-
-
USART
-
I2C
-
-
-
I2C2_TX
I2C2_RX
I2C1_TX
I2C1_RX
TIM1
-
TIM1_CH1
-
TIM1_CH4
TIM1_TRIG
TIM1_COM
TIM1_UP
TIM1_CH3
TIM1_CH2
TIM1_CH1
-
TIM2
TIM2_CH3
TIM2_UP
-
-
TIM2_CH1
-
TIM2_CH2
TIM2_CH4
TIM3
-
TIM3_CH3
TIM3_CH4
TIM3_UP
-
-
TIM3_CH1
TIM3_TRIG
-
TIM4
TIM4_CH1
-
-
TIM4_CH2
TIM4_CH3
-
TIM4_UP
TIM6/DAC_
Channel1
-
TIM7/DAC_
Channel2
-
USART3_TX USART3_RX USART1_TX USART1_RX USART2_RX USART2_TX
TIM6_UP/DA
C_Channel1
-
-
TIM7_UP/DA
C_Channel2
-
-
-
-
-
TIM15
-
-
-
-
TIM15_CH1
TIM15_UP
TIM15_TRIG
TIM15_COM
TIM16
-
-
-
-
-
TIM16_CH1
TIM16_UP
-
TIM17
-
-
-
-
-
-
TIM17_CH1
TIM17_UP
DMA2 controller
The 5 requests from the peripherals (TIMx[5,6,7], SPI3, UARTx[4,5], DAC_Channel[1,2])
are simply logically ORed before entering the DMA2, this means that only one request must
be enabled at a time. Refer to Figure 23.
The peripheral DMA requests can be independently activated/de-activated by programming
the DMA control bit in the registers of the corresponding peripheral.
Note:
150/713
The DMA2 controller and its relative requests are available only in high-density value line
devices.
Doc ID16188 Rev 5
RM0041
Direct memory access controller (DMA)
Figure 23. DMA2 request mapping
Peripheral request signals
Fixed hardware priority
TIM5_CH4
TIM5_TRIG
HIGH PRIORITY
HW request 1
UART5_TX
SPI3_RX
Channel 1
SW trigger (MEM2MEM bit)
Channel 1 EN bit
TIM5_CH3
TIM5_UP
SPI3_TX
HW request 2
Channel 2
SW trigger (MEM2MEM bit)
Channel 2 EN bit
HW request 3
UART4_RX
TIM6_UP/DAC_Channel1(1)
Channel 3
SW trigger (MEM2MEM bit)
internal
Channel 3 EN bit
DMA2
TIM5_CH2
UART5_RX
TIM7_UP/DAC_Channel2(1)
HW request 4
request
Channel 4
SW trigger (MEM2MEM bit)
Channel 4 EN bit
HW request 5
TIM5_CH1
UART4_TX
Channel 5
LOW PRIORITY
SW trigger (MEM2MEM bit)
Channel 5 EN bit
1. For high-density value line devices, the TIM6_DAC1 and TIM7_DAC2 DMA requests are mapped
respectively on DMA1 Channel 3 and DMA1 Channel 4 only if the TIM67_DAC_DMA_REMAP bit in the
AFIO_MAPR2 register is set, and mapped respectively on DMA2 Channel 3 and DMA2 Channel 4 when
the TIM67_DAC_DMA_REMAP bit in the AFIO_MAPR2 register is reset. On low- and medium -density
devices the TIM6_DAC1 and TIM7_DAC2 DMA requests are always mapped respectively on DMA1
Channel 3 and DMA1 Channel 4. For more details refer to the AFIO section.
Table 55 lists the DMA2 requests for each channel.
Table 55. Summary of DMA2 requests for each channel
Peripherals
Channel 1
Channel 2
Channel 3
Channel 4
SPI3
SPI3_RX
SPI3_TX
-
-
UART4
-
-
UART4_RX
-
UART4_TX
UART5
UART5_TX
-
-
UART5_RX
-
TIM5
TIM5_CH4
TIM5_TRIG
TIM5_CH3
TIM5_UP
-
TIM5_CH2
TIM5_CH1
TIM6/
DAC_Channel1
-
-
TIM6_UP/
DAC_Channel1
-
-
TIM7/
DAC_Channel2
-
-
-
TIM7_UP/
DAC_Channel2
-
Doc ID16188 Rev 5
Channel 5
151/713
159
Direct memory access controller (DMA)
9.4
RM0041
DMA registers
Refer to for a list of abbreviations used in register descriptions.
Note:
In the following registers, all bits related to channel6 and channel7 are not relevant for
DMA2 since it has only 5 channels.
The peripheral registers can be accessed by bytes (8-bit), half-words (16-bit) or words (32bit).
9.4.1
DMA interrupt status register (DMA_ISR)
Address offset: 0x00
Reset value: 0x0000 0000
31
30
29
28
Reserved
27
26
25
24
23
22
21
20
19
18
17
16
TEIF7
HTIF7
TCIF7
GIF7
TEIF6
HTIF6
TCIF6
GIF6
TEIF5
HTIF5
TCIF5
GIF5
r
r
r
r
r
r
r
r
r
r
r
r
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
TEIF4
HTIF4
TCIF4
GIF4
TEIF3
HTIF3
TCIF3
GIF3
TEIF2
HTIF2
TCIF2
GIF2
TEIF1
HTIF1
TCIF1
GIF1
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
Bits 31:28
Reserved, must be kept at reset value.
Bits 27, 23, 19, 15, TEIFx: Channel x transfer error flag (x = 1 ..7)
11, 7, 3
This bit is set by hardware. It is cleared by software writing 1 to the corresponding bit in the
DMA_IFCR register.
0: No transfer error (TE) on channel x
1: A transfer error (TE) occurred on channel x
Bits 26, 22, 18, 14, HTIFx: Channel x half transfer flag (x = 1 ..7)
10, 6, 2
This bit is set by hardware. It is cleared by software writing 1 to the corresponding bit in the
DMA_IFCR register.
0: No half transfer (HT) event on channel x
1: A half transfer (HT) event occurred on channel x
Bits 25, 21, 17, 13, TCIFx: Channel x transfer complete flag (x = 1 ..7)
9, 5, 1
This bit is set by hardware. It is cleared by software writing 1 to the corresponding bit in the
DMA_IFCR register.
0: No transfer complete (TC) event on channel x
1: A transfer complete (TC) event occurred on channel x
Bits 24, 20, 16, 12, GIFx: Channel x global interrupt flag (x = 1 ..7)
8, 4, 0
This bit is set by hardware. It is cleared by software writing 1 to the corresponding bit in the
DMA_IFCR register.
0: No TE, HT or TC event on channel x
1: A TE, HT or TC event occurred on channel x
152/713
Doc ID16188 Rev 5
RM0041
Direct memory access controller (DMA)
9.4.2
DMA interrupt flag clear register (DMA_IFCR)
Address offset: 0x04
Reset value: 0x0000 0000
31
30
29
28
27
CTEIF
7
Reserved
26
25
24
CHTIF
CTCIF7
7
CGIF7
23
22
21
20
CTEIF6 CHTIF6 CTCIF6 CGIF6
19
18
17
16
CTEIF5 CHTIF5 CTCIF5
CGIF5
w
w
w
w
w
w
w
w
w
w
w
w
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CTEIF
4
CHTIF
4
CTCIF
4
CGIF4
CTEIF
3
w
w
w
w
w
Bits 31:28
CHTIF
CTCIF3
3
w
w
CGIF3
w
CTEIF2 CHTIF2 CTCIF2 CGIF2
w
w
w
w
CTEIF1 CHTIF1 CTCIF1
w
w
w
CGIF1
w
Reserved, must be kept at reset value.
Bits 27, 23, 19, 15, CTEIFx: Channel x transfer error clear (x = 1 ..7)
11, 7, 3
This bit is set and cleared by software.
0: No effect
1: Clears the corresponding TEIF flag in the DMA_ISR register
Bits 26, 22, 18, 14, CHTIFx: Channel x half transfer clear (x = 1 ..7)
10, 6, 2
This bit is set and cleared by software.
0: No effect
1: Clears the corresponding HTIF flag in the DMA_ISR register
Bits 25, 21, 17, 13, CTCIFx: Channel x transfer complete clear (x = 1 ..7)
9, 5, 1
This bit is set and cleared by software.
0: No effect
1: Clears the corresponding TCIF flag in the DMA_ISR register
Bits 24, 20, 16, 12, CGIFx: Channel x global interrupt clear (x = 1 ..7)
8, 4, 0
This bit is set and cleared by software.
0: No effect
1: Clears the GIF, TEIF, HTIF and TCIF flags in the DMA_ISR register
Doc ID16188 Rev 5
153/713
159
Direct memory access controller (DMA)
9.4.3
RM0041
DMA channel x configuration register (DMA_CCRx) (x = 1..7,
where x = channel number)
Address offset: 0x08 + 0d20 × (channel number – 1)
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
7
6
5
4
3
2
1
0
MINC
PINC
CIRC
DIR
TEIE
HTIE
TCIE
EN
rw
rw
rw
rw
rw
rw
rw
rw
Reserved
15
14
Res.
MEM2
MEM
rw
13
12
PL[1:0]
rw
Bits 31:15
rw
11
10
9
8
MSIZE[1:0]
PSIZE[1:0]
rw
rw
rw
rw
Reserved, must be kept at reset value.
Bit 14 MEM2MEM: Memory to memory mode
This bit is set and cleared by software.
0: Memory to memory mode disabled
1: Memory to memory mode enabled
Bits 13:12 PL[1:0]: Channel priority level
These bits are set and cleared by software.
00: Low
01: Medium
10: High
11: Very high
Bits 11:10 MSIZE[1:0]: Memory size
These bits are set and cleared by software.
00: 8-bits
01: 16-bits
10: 32-bits
11: Reserved
Bits 9:8 PSIZE[1:0]: Peripheral size
These bits are set and cleared by software.
00: 8-bits
01: 16-bits
10: 32-bits
11: Reserved
Bit 7 MINC: Memory increment mode
This bit is set and cleared by software.
0: Memory increment mode disabled
1: Memory increment mode enabled
Bit 6 PINC: Peripheral increment mode
This bit is set and cleared by software.
0: Peripheral increment mode disabled
1: Peripheral increment mode enabled
Bit 5 CIRC: Circular mode
This bit is set and cleared by software.
0: Circular mode disabled
1: Circular mode enabled
154/713
Doc ID16188 Rev 5
RM0041
Direct memory access controller (DMA)
Bit 4 DIR: Data transfer direction
This bit is set and cleared by software.
0: Read from peripheral
1: Read from memory
Bit 3 TEIE: Transfer error interrupt enable
This bit is set and cleared by software.
0: TE interrupt disabled
1: TE interrupt enabled
Bit 2 HTIE: Half transfer interrupt enable
This bit is set and cleared by software.
0: HT interrupt disabled
1: HT interrupt enabled
Bit 1 TCIE: Transfer complete interrupt enable
This bit is set and cleared by software.
0: TC interrupt disabled
1: TC interrupt enabled
Bit 0 EN: Channel enable
This bit is set and cleared by software.
0: Channel disabled
1: Channel enabled
9.4.4
DMA channel x number of data register (DMA_CNDTRx) (x = 1..7,
where x = channel number)
Address offset: 0x0C + 0d20 × (channel number – 1)
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
20
19
18
17
16
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
Reserved
NDT
rw
rw
rw
Bits 31:16
rw
rw
rw
rw
rw
Reserved, must be kept at reset value.
Bits 15:0 NDT[15:0]: Number of data to transfer
Number of data to be transferred (0 up to 65535). This register can only be written when the
channel is disabled. Once the channel is enabled, this register is read-only, indicating the
remaining bytes to be transmitted. This register decrements after each DMA transfer.
Once the transfer is completed, this register can either stay at zero or be reloaded
automatically by the value previously programmed if the channel is configured in autoreload mode.
If this register is zero, no transaction can be served whether the channel is enabled or not.
Doc ID16188 Rev 5
155/713
159
Direct memory access controller (DMA)
9.4.5
RM0041
DMA channel x peripheral address register (DMA_CPARx) (x = 1..7,
where x = channel number)
Address offset: 0x10 + 0d20 × (channel number – 1)
Reset value: 0x0000 0000
This register must not be written when the channel is enabled.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
PA
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 31:0 PA[31:0]: Peripheral address
Base address of the peripheral data register from/to which the data will be read/written.
When PSIZE is 01 (16-bit), the PA[0] bit is ignored. Access is automatically aligned to a halfword address.
When PSIZE is 10 (32-bit), PA[1:0] are ignored. Access is automatically aligned to a word
address.
9.4.6
DMA channel x memory address register (DMA_CMARx) (x = 1..7,
where x = channel number)
Address offset: 0x14 + 0d20 × (channel number – 1)
Reset value: 0x0000 0000
This register must not be written when the channel is enabled.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
MA
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 31:0 MA[31:0]: Memory address
Base address of the memory area from/to which the data will be read/written.
When MSIZE is 01 (16-bit), the MA[0] bit is ignored. Access is automatically aligned to a
half-word address.
When MSIZE is 10 (32-bit), MA[1:0] are ignored. Access is automatically aligned to a word
address.
156/713
Doc ID16188 Rev 5
RM0041
9.4.7
Direct memory access controller (DMA)
DMA register map
The following table gives the DMA register map and the reset values.
HTIF2
TCIF2
GIF2
TEIF1
HTIF1
TCIF1
GIF1
0
0
0
0
0
0
0
0
0
0
0
0
CHTIF6
CTCIF6
CGIF6
CTEIF5
CHTIF5
CTCIF5
CGIF5
CTEIF4
CHTIF4
CTCIF4
CGIF4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0x038
0x03C
0x040
TEIE
HTIE
TCIE
EN
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MA[31:0]
0
0
0
DMA_CPAR2
Reset value
HTIE
TCIE
EN
0
TEIE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DMA_CMAR2
Reset value
0
NDT[15:0]
Reserved
Reset value
0
DIR
0
DMA_CNDTR2
PL
[1:0]
PINC
Reserved
PSIZE [1:0]
MEM2MEM
DMA_CCR2
CIRC
Reserved
0
0
MA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DMA_CPAR3
Reset value
EN
0
TCIE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DMA_CMAR3
Reset value
0
NDT[15:0]
Reserved
Reset value
0
HTIE
0
DMA_CNDTR3
PL
[1:0]
TEIE
Reserved
DIR
MEM2MEM
DMA_CCR3
PINC
Reserved
Reset value
0x034
0
DIR
0
0x02C
0x030
0
0
CIRC
0x028
0
MINC
0x024
0
PINC
0
Reset value
0x020
0
CIRC
0
0x018
0x01C
0
PA[31:0]
DMA_CMAR1
Reset value
0
PSIZE [1:0]
0x014
0
DMA_CPAR1
Reset value
0
NDT[15:0]
Reserved
Reset value
0
0
M SIZE [1:0]
0x010
DMA_CNDTR1
0
0
M SIZE [1:0]
0x00C
0
MINC
Reset value
PL
[1:0]
0
PSIZE [1:0]
Reserved
0
M SIZE [1:0]
DMA_CCR1
0
CGIF1
GIF3
TEIF2
0
CTCIF1
TCIF3
0
CHTIF1
HTIF3
0
CTEIF1
GIF4
TEIF3
0
CGIF2
TCIF4
0
CTCIF2
HTIF4
0
CHTIF2
GIF5
TEIF4
0
CTEIF2
TCIF5
0
MINC
HTIF5
0
CGIF3
GIF6
TEIF5
0
CTCIF3
TCIF6
0
CHTIF3
HTIF6
0
CTEIF3
GIF7
TEIF6
0
MEM2MEM
0x008
0
CTEIF6
Reset value
TCIF7
Reserved
0
CGIF7
DMA_IFCR
0
CTCIF7
0x004
TEIF7
Reserved
Reset value
HTIF7
DMA_ISR
CTEIF7
0x000
Register
CHTIF7
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 56. DMA register map and reset values
0
0
MA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Reserved
Doc ID16188 Rev 5
157/713
159
Direct memory access controller (DMA)
RM0041
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0x088
158/713
MINC
PINC
CIRC
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MA[31:0]
0
0
DIR
HTIE
TCIE
EN
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DMA_CMAR5
Reset value
0
MINC
0
DMA_CPAR5
Reset value
0
NDT[15:0]
Reserved
Reset value
0
TEIE
0
DMA_CNDTR5
PL
[1:0]
CIRC
Reserved
PSIZE [1:0]
MEM2MEM
DMA_CCR5
PINC
Reserved
0
0
MA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DMA_CPAR6
Reset value
TCIE
EN
0
HTIE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DMA_CMAR6
Reset value
0
NDT[15:0]
Reserved
Reset value
0
DIR
0
DMA_CNDTR6
PL
[1:0]
TEIE
Reserved
CIRC
MEM2MEM
DMA_CCR6
PINC
Reserved
0
0
MA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DMA_CPAR7
Reset value
0
0
EN
0
0
0
0
0
0
0
0
NDT[15:0]
Reserved
Reset value
0
TCIE
0
DMA_CNDTR7
PL
[1:0]
HTIE
Reserved
DIR
MEM2MEM
DMA_CCR7
TEIE
Reserved
Reset value
0x084
EN
0
0x07C
0x080
0
0
CIRC
0x078
0
PINC
0x074
TCIE
0
Reset value
0x070
HTIE
0
0x068
0x06C
0
MINC
0x064
0
0
PSIZE [1:0]
0x060
DIR
0
Reset value
0x05C
TEIE
0
0x054
0x058
0
0
PA[31:0]
DMA_CMAR4
Reset value
0
0
PSIZE [1:0]
0x050
0
DMA_CPAR4
Reset value
0
0
NDT[15:0]
Reserved
Reset value
0
0
M SIZE [1:0]
0x04C
DMA_CNDTR4
0
0
M SIZE [1:0]
0x048
0
MINC
Reset value
PL
[1:0]
PSIZE [1:0]
Reserved
M SIZE [1:0]
DMA_CCR4
M SIZE [1:0]
0x044
Register
MEM2MEM
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 56. DMA register map and reset values (continued)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Doc ID16188 Rev 5
0
RM0041
Direct memory access controller (DMA)
Offset
0x08C
0x090
Register
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 56. DMA register map and reset values (continued)
DMA_CMAR7
Reset value
MA[31:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Reserved
Refer to Table 1 on page 36 and Table 2 on page 37 for the register boundary addresses.
Doc ID16188 Rev 5
159/713
159
Analog-to-digital converter (ADC)
10
RM0041
Analog-to-digital converter (ADC)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This Section applies to the whole STM32F100xx family, unless otherwise specified.
10.1
ADC introduction
The 12-bit ADC is a successive approximation analog-to-digital converter. It has up to 18
multiplexed channels allowing it measure signals from 16 external and two internal sources.
A/D conversion of the various channels can be performed in single, continuous, scan or
discontinuous mode. The result of the ADC is stored in a left-aligned or right-aligned 16-bit
data register.
The analog watchdog feature allows the application to detect if the input voltage goes
outside the user-defined high or low thresholds.
The ADC input clock is generated from the PCLK2 clock divided by a prescaler, refer to
Figure 8: STM32F100xx clock tree (low and medium-density devices) and Figure 9:
STM32F100xx clock tree (high-density devices).
10.2
ADC main features
•
12-bit resolution
•
Interrupt generation at End of Conversion, End of Injected conversion and Analog
watchdog event
•
Single and continuous conversion modes
•
Scan mode for automatic conversion of channel 0 to channel ‘n’
•
Self-calibration
•
Data alignment with in-built data coherency
•
Channel by channel programmable sampling time
•
External trigger option for both regular and injected conversion
•
Discontinuous mode
•
ADC conversion time:
–
STM32F100xx value line devices: 1.17 µs at 24 MHz
•
ADC supply requirement: 2.4 V to 3.6 V
•
ADC input range: VREF- ≤VIN ≤VREF+
•
DMA request generation during regular channel conversion
The block diagram of the ADC is shown in Figure 24.
Note:
160/713
VREF-,if available (depending on package), must be tied to VSSA.
Doc ID16188 Rev 5
RM0041
ADC functional description
Figure 24 shows a single ADC block diagramand Table 57 gives the ADC pin description.
Figure 24. Single ADC block diagram
&LAGS
%NDOFCONVERSION
%NDOFINJECTEDCONVERSION
!NALOGWATCHDOGEVENT
)NTERRUPT
ENABLEBITS
%/#
%/#)%
*%/#
*%/#)%
!7$
!7$)%
!$#)NTERRUPTTO.6)#
!NALOG
WATCHDOG
#OMPARE2ESULT
(IGH4HRESHOLDBITS
,OW4HRESHOLDBITS
!DDRESSDATABUS
10.3
Analog-to-digital converter (ADC)
)NJECTEDDATAREGISTERS
§BITS
62%&
62%&
2EGULARDATAREGISTER
BITS
6$$!
633!
!NALOG
$-!REQUEST
-58
!$#X?).
!$#X?).
'0)/
0ORTS
UPTO
UPTO
!$#X?).
!$##,+
)NJECTED
CHANNELS
!NALOG TO DIGITAL
2EGULAR
CHANNELS
CONVERTER
4EMPSENSOR
62%&).4
&ROM!$#PRESCALER
*%843%,;=BITS
4)-?42'/
4)-?#(
4)-?42'/
4)-?#(
4)-?#(
4)-?42'/
*%842)'
BIT
3TARTTRIGGER
INJECTEDGROUP
%84)?
%843%,;=BITS
4)-?#(
4)-?#(
4)-?#(
4)-?#(
4)-?42'/
4)-?#(
%842)'
BIT
3TARTTRIGGER
REGULARGROUP
%84)?
AI
Doc ID16188 Rev 5
161/713
187
Analog-to-digital converter (ADC)
RM0041
Table 57. ADC pins
Name
Signal type
Remarks
VREF+
Input, analog reference
positive
The higher/positive reference voltage for the ADC,
2.4 V ≤VREF+ ≤VDDA
VDDA(1)
Input, analog supply
Analog power supply equal to VDD and
2.4 V ≤VDDA ≤3.6 V
VREF-
Input, analog reference
negative
The lower/negative reference voltage for the ADC,
VREF- = VSSA
VSSA(1)
Input, analog supply
ground
Ground for analog power supply equal to VSS
ADCx_IN[15:0]
Analog signals
Up to 21 analog channels(2)
1. VDDA and VSSA have to be connected to VDD and VSS, respectively.
2. For full details about the ADC I/O pins, refer to the “Pinouts and pin descriptions” section of the
corresponding device datasheet.
10.3.1
ADC on-off control
The ADC can be powered-on by setting the ADON bit in the ADC_CR2 register. When the
ADON bit is set for the first time, it wakes up the ADC from Power Down mode.
Conversion starts when ADON bit is set for a second time by software after ADC power-up
time (tSTAB).
The conversion can be stopped, and the ADC put in power down mode by resetting the
ADON bit. In this mode the ADC consumes almost no power (only a few µA).
10.3.2
ADC clock
The ADCCLK clock provided by the Clock Controller is synchronous with the PCLK2 (APB2
clock). The RCC controller has a dedicated programmable prescaler for the ADC clock,
refer to Section 6: Reset and clock control (RCC) for more details.
10.3.3
Channel selection
There are 16 multiplexed channels. It is possible to organize the conversions in two groups:
regular and injected. A group consists of a sequence of conversions which can be done on
any channel and in any order. For instance, it is possible to do the conversion in the
following order: Ch3, Ch8, Ch2, Ch2, Ch0, Ch2, Ch2, Ch15.
•
The regular group is composed of up to 16 conversions. The regular channels and
their order in the conversion sequence must be selected in the ADC_SQRx registers.
The total number of conversions in the regular group must be written in the L[3:0] bits in
the ADC_SQR1 register.
•
The injected group is composed of up to 4 conversions. The injected channels and
their order in the conversion sequence must be selected in the ADC_JSQR register.
The total number of conversions in the injected group must be written in the L[1:0] bits
in the ADC_JSQR register.
If the ADC_SQRx or ADC_JSQR registers are modified during a conversion, the current
conversion is reset and a new start pulse is sent to the ADC to convert the new chosen
group.
162/713
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
Temperature sensor/VREFINT internal channels
The Temperature sensor is connected to channel ADCx_IN16 and the internal reference
voltage VREFINT is connected to ADCx_IN17. These two internal channels can be selected
and converted as injected or regular channels.
Note:
The sensor and VREFINT are only available on the master ADC1 peripheral.
10.3.4
Single conversion mode
In Single conversion mode the ADC does one conversion. This mode is started either by
setting the ADON bit in the ADC_CR2 register (for a regular channel only) or by external
trigger (for a regular or injected channel), while the CONT bit is 0.
Once the conversion of the selected channel is complete:
•
•
If a regular channel was converted:
–
The converted data is stored in the 16-bit ADC_DR register
–
The EOC (End Of Conversion) flag is set
–
and an interrupt is generated if the EOCIE is set.
If an injected channel was converted:
–
The converted data is stored in the 16-bit ADC_DRJ1 register
–
The JEOC (End Of Conversion Injected) flag is set
–
and an interrupt is generated if the JEOCIE bit is set.
The ADC is then stopped.
10.3.5
Continuous conversion mode
In continuous conversion mode ADC starts another conversion as soon as it finishes one.
This mode is started either by external trigger or by setting the ADON bit in the ADC_CR2
register, while the CONT bit is 1.
After each conversion:
•
•
10.3.6
If a regular channel was converted:
–
The converted data is stored in the 16-bit ADC_DR register
–
The EOC (End Of Conversion) flag is set
–
An interrupt is generated if the EOCIE is set.
If an injected channel was converted:
–
The converted data is stored in the 16-bit ADC_DRJ1 register
–
The JEOC (End Of Conversion Injected) flag is set
–
An interrupt is generated if the JEOCIE bit is set.
Timing diagram
As shown in Figure 25, the ADC needs a stabilization time of tSTAB before it starts
converting accurately. After the start of ADC conversion and after 14 clock cycles, the EOC
flag is set and the 16-bit ADC Data register contains the result of the conversion.
Doc ID16188 Rev 5
163/713
187
Analog-to-digital converter (ADC)
RM0041
Figure 25. Timing diagram
!$#?#,+
!$/.
3734!24
*3734!24
3TARTSTCONVERSION
3TARTNEXTCONVERSION
!$#CONVERSION
!$#
.EXT!$#CONVERSION
#ONVERSIONTIME
T34!"
TOTALCONVTIME
%/#
3OFTWARECLEARSTHE%/#BIT
AIB
10.3.7
Analog watchdog
The AWD analog watchdog status bit is set if the analog voltage converted by the ADC is
below a low threshold or above a high threshold. These thresholds are programmed in the
12 least significant bits of the ADC_HTR and ADC_LTR 16-bit registers. An interrupt can be
enabled by using the AWDIE bit in the ADC_CR1 register.
The threshold value is independent of the alignment selected by the ALIGN bit in the
ADC_CR2 register. The comparison is done before the alignment (see Section 10.5).
The analog watchdog can be enabled on one or more channels by configuring the
ADC_CR1 register as shown in Table 58.
Figure 26. Analog watchdog guarded area
$QDORJYROWDJH
+LJKHUWKUHVKROG
+75
*XDUGHGDUHD
/RZHUWKUHVKROG
/75
DL
Table 58. Analog watchdog channel selection
Channels to be guarded by analog
watchdog
164/713
ADC_CR1 register control bits (x = don’t care)
AWDSGL bit
AWDEN bit
JAWDEN bit
None
x
0
0
All injected channels
0
0
1
All regular channels
0
1
0
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
Table 58. Analog watchdog channel selection (continued)
Channels to be guarded by analog
watchdog
ADC_CR1 register control bits (x = don’t care)
AWDSGL bit
AWDEN bit
JAWDEN bit
All regular and injected channels
0
1
1
Single(1)
injected channel
1
0
1
(1)
regular channel
1
1
0
(1)
regular or injected channel
1
1
1
Single
Single
1. Selected by AWDCH[4:0] bits
10.3.8
Scan mode
This mode is used to scan a group of analog channels.
Scan mode can be selected by setting the SCAN bit in the ADC_CR1 register. Once this bit
is set, ADC scans all the channels selected in the ADC_SQRx registers (for regular
channels) or in the ADC_JSQR (for injected channels). A single conversion is performed for
each channel of the group. After each end of conversion the next channel of the group is
converted automatically. If the CONT bit is set, conversion does not stop at the last selected
group channel but continues again from the first selected group channel.
When using scan mode, DMA bit must be set and the direct memory access controller is
used to transfer the converted data of regular group channels to SRAM after each update of
the ADC_DR register.
The injected channel converted data is always stored in the ADC_JDRx registers.
10.3.9
Injected channel management
Triggered injection
To use triggered injection, the JAUTO bit must be cleared and SCAN bit must be set in the
ADC_CR1 register.
Note:
1.
Start conversion of a group of regular channels either by external trigger or by setting
the ADON bit in the ADC_CR2 register.
2.
If an external injected trigger occurs during the regular group channel conversion, the
current conversion is reset and the injected channel sequence is converted in Scan
once mode.
3.
Then, the regular group channel conversion is resumed from the last interrupted
regular conversion. If a regular event occurs during an injected conversion, it doesn’t
interrupt it but the regular sequence is executed at the end of the injected sequence.
Figure 27 shows the timing diagram.
When using triggered injection, the interval between trigger events must be longer than the
injection sequence. For instance, if the sequence length is 28 ADC clock cycles (that is two
conversions with a 1.5 clock-period sampling time), the minimum interval between triggers
must be 29 ADC clock cycles.
Doc ID16188 Rev 5
165/713
187
Analog-to-digital converter (ADC)
RM0041
Auto-injection
If the JAUTO bit is set, then the injected group channels are automatically converted after
the regular group channels. This can be used to convert a sequence of up to 20 conversions
programmed in the ADC_SQRx and ADC_JSQR registers.
In this mode, external trigger on injected channels must be disabled.
If the CONT bit is also set in addition to the JAUTO bit, regular channels followed by injected
channels are continuously converted.
For ADC clock prescalers ranging from 4 to 8, a delay of 1 ADC clock period is automatically
inserted when switching from regular to injected sequence (respectively injected to regular).
When the ADC clock prescaler is set to 2, the delay is 2 ADC clock periods.
Note:
It is not possible to use both auto-injected and discontinuous modes simultaneously.
Figure 27. Injected conversion latency
!$##,+
)NJECTIONEVENT
2ESET!$#
3/#
MAXLATENCY AI
1. The maximum latency value can be found in the electrical characteristics of the STM32F101xx and
STM32F103xx datasheets.
10.3.10
Discontinuous mode
Regular group
This mode is enabled by setting the DISCEN bit in the ADC_CR1 register. It can be used to
convert a short sequence of n conversions (n <=8) which is a part of the sequence of
conversions selected in the ADC_SQRx registers. The value of n is specified by writing to
the DISCNUM[2:0] bits in the ADC_CR1 register.
When an external trigger occurs, it starts the next n conversions selected in the ADC_SQRx
registers until all the conversions in the sequence are done. The total sequence length is
defined by the L[3:0] bits in the ADC_SQR1 register.
Example:
n = 3, channels to be converted = 0, 1, 2, 3, 6, 7, 9, 10
1st trigger: sequence converted 0, 1, 2. An EOC event is generated at each conversion
166/713
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
2nd trigger: sequence converted 3, 6, 7. An EOC event is generated at each
conversion
3rd trigger: sequence converted 9, 10. An EOC event is generated at each conversion
4th trigger: sequence converted 0, 1, 2. An EOC event is generated at each conversion
Note:
When a regular group is converted in discontinuous mode, no rollover will occur. When all
sub groups are converted, the next trigger starts conversion of the first sub-group.
In the example above, the 4th trigger reconverts the 1st sub-group channels 0, 1 and 2.
Injected group
This mode is enabled by setting the JDISCEN bit in the ADC_CR1 register. It can be used to
convert the sequence selected in the ADC_JSQR register, channel by channel, after an
external trigger event.
When an external trigger occurs, it starts the next channel conversions selected in the
ADC_JSQR registers until all the conversions in the sequence are done. The total sequence
length is defined by the JL[1:0] bits in the ADC_JSQR register.
Example:
n = 1, channels to be converted = 1, 2, 3
1st trigger: channel 1 converted
2nd trigger: channel 2 converted
3rd trigger: channel 3 converted and EOC and JEOC events generated
4th trigger: channel 1
Note:
When all injected channels are converted, the next trigger starts the conversion of the first
injected channel. In the example above, the 4th trigger reconverts the 1st injected channel
1.
It is not possible to use both auto-injected and discontinuous modes simultaneously.
The user must avoid setting discontinuous mode for both regular and injected groups
together. Discontinuous mode must be enabled only for one group conversion.
10.4
Calibration
The ADC has an built-in self calibration mode. Calibration significantly reduces accuracy
errors due to internal capacitor bank variations. During calibration, an error-correction code
(digital word) is calculated for each capacitor, and during all subsequent conversions, the
error contribution of each capacitor is removed using this code.
Calibration is started by setting the CAL bit in the ADC_CR2 register. Once calibration is
over, the CAL bit is reset by hardware and normal conversion can be performed. It is
recommended to calibrate the ADC once at power-on. The calibration codes are stored in
the ADC_DR as soon as the calibration phase ends.
Note:
It is recommended to perform a calibration after each power-up.
Before starting a calibration, the ADC must have been in power-on state (ADON bit = ‘1’) for
at least two ADC clock cycles.
Doc ID16188 Rev 5
167/713
187
Analog-to-digital converter (ADC)
RM0041
Figure 28. Calibration timing diagram
CLK
Calibration Reset by Hardware
Calibration ongoing
tCAL
CAL
Normal ADC Conversion
ADC
Conversion
10.5
Data alignment
ALIGN bit in the ADC_CR2 register selects the alignment of data stored after conversion.
Data can be left or right aligned as shown in Figure 29. and Figure 30.
The injected group channels converted data value is decreased by the user-defined offset
written in the ADC_JOFRx registers so the result can be a negative value. The SEXT bit is
the extended sign value.
For regular group channels no offset is subtracted so only twelve bits are significant.
Figure 29. Right alignment of data
)NJECTEDGROUP
3%84 3%84 3%84 3%84
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
2EGULARGROUP
AI
Figure 30. Left alignment of data
)NJECTEDGROUP
3%84 $
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
2EGULARGROUP
$
$
$
$
AI
168/713
Doc ID16188 Rev 5
RM0041
10.6
Analog-to-digital converter (ADC)
Channel-by-channel programmable sample time
ADC samples the input voltage for a number of ADC_CLK cycles which can be modified using the SMP[2:0] bits in the ADC_SMPR1 and ADC_SMPR2 registers. Each channel can be
sampled with a different sample time.
The total conversion time is calculated as follows:
Tconv = Sampling time + 12.5 cycles
Example:
With an ADCCLK = 12 MHz and a sampling time of 1.5 cycles:
Tconv = 1.5 + 12.5 = 14 cycles = 1.17 µs
10.7
Conversion on external trigger
Conversion can be triggered by an external event (e.g. timer capture, EXTI line). If the EXTTRIG control bit is set then external events are able to trigger a conversion. The EXTSEL[2:0] and JEXTSEL[2:0] control bits allow the application to select decide which out of 8
possible events can trigger conversion for the regular and injected groups.
Note:
When an external trigger is selected for ADC regular or injected conversion, only the rising
edge of the signal can start the conversion.
Table 59. External trigger for regular channels for ADC1
Source
Type
EXTSEL[2:0]
TIM1_CC1 event
000
TIM1_CC2 event
001
TIM1_CC3 event
TIM2_CC2 event
Internal signal from on-chip
timers
010
011
TIM3_TRGO event
100
TIM4_CC4 event
101
EXTI line 11
External pin
110
SWSTART
Software control bit
111
Table 60. External trigger for injected channels for ADC1
Source
Connection type
JEXTSEL[2:0]
TIM1_TRGO event
000
TIM1_CC4 event
001
TIM2_TRGO event
TIM2_CC1 event
Internal signal from on-chip
timers
010
011
TIM3_CC4 event
100
TIM4_TRGO event
101
EXTI line 15
External pin
110
JSWSTART
Software control bit
111
Doc ID16188 Rev 5
169/713
187
Analog-to-digital converter (ADC)
RM0041
The software source trigger events can be generated by setting a bit in a register
(SWSTART and JSWSTART in ADC_CR2).
A regular group conversion can be interrupted by an injected trigger.
10.8
DMA request
Since converted regular channels value are stored in a unique data register, it is necessary
to use DMA for conversion of more than one regular channel. This avoids the loss of data
already stored in the ADC_DR register.
Only the end of conversion of a regular channel generates a DMA request, which allows the
transfer of its converted data from the ADC_DR register to the destination location selected
by the user.
10.9
Temperature sensor
The temperature sensor can be used to measure the ambient temperature (TA) of the
device.
The temperature sensor is internally connected to the ADCx_IN16 input channel which is
used to convert the sensor output voltage into a digital value. The recommended sampling
time for the temperature sensor is 17.1 µs.
The block diagram of the temperature sensor is shown in Figure 31.
When not in use, this sensor can be put in power down mode.
Note:
The TSVREFE bit must be set to enable both internal channels: ADCx_IN16 (temperature
sensor) and ADCx_IN17 (VREFINT) conversion.
The temperature sensor output voltage changes linearly with temperature. The offset of this
line varies from chip to chip due to process variation (up to 45 °C from one chip to another).
The internal temperature sensor is more suited to applications that detect temperature
variations instead of absolute temperatures. If accurate temperature readings are needed,
an external temperature sensor part should be used.
170/713
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
Figure 31. Temperature sensor and VREFINT channel block diagram
7695()(FRQWUROELW
9 6(16(
$'&B,1
FRQYHUWHGGDWD
$'& ,QWHUQDO
SRZHUEORFN
95(),17
$GGUHVVGDWDEXV
7HPSHUDWXUH
VHQVRU
$'&B,1
069
Doc ID16188 Rev 5
171/713
187
Analog-to-digital converter (ADC)
RM0041
Reading the temperature
To use the sensor:
1.
Select the ADCx_IN16 input channel.
2.
Select a sample time of 17.1 µs
3.
Set the TSVREFE bit in the ADC control register 2 (ADC_CR2) to wake up the
temperature sensor from power down mode.
4.
Start the ADC conversion by setting the ADON bit (or by external trigger).
5.
Read the resulting VSENSE data in the ADC data register
6.
Obtain the temperature using the following formula:
Temperature (in °C) = {(V25 - VSENSE) / Avg_Slope} + 25.
Where,
V25 = VSENSE value for 25° C and
Avg_Slope = Average Slope for curve between Temperature vs. VSENSE (given in
mV/° C or µV/ °C).
Refer to the Electrical characteristics section for the actual values of V25 and
Avg_Slope.
Note:
The sensor has a startup time after waking from power down mode before it can output
VSENSE at the correct level. The ADC also has a startup time after power-on, so to minimize
the delay, the ADON and TSVREFE bits should be set at the same time.
10.10
ADC interrupts
An interrupt can be produced on end of conversion for regular and injected groups and
when the analog watchdog status bit is set. Separate interrupt enable bits are available for
flexibility.
Two other flags are present in the ADC_SR register, but there is no interrupt associated with
them:
•
JSTRT (Start of conversion for injected group channels)
•
STRT (Start of conversion for regular group channels)
Table 61. ADC interrupts
Interrupt event
172/713
Event flag
Enable Control bit
End of conversion regular group
EOC
EOCIE
End of conversion injected group
JEOC
JEOCIE
Analog watchdog status bit is set
AWD
AWDIE
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
10.11
ADC registers
Refer to Section 1.1 on page 32 for a list of abbreviations used in register descriptions.
The peripheral registers have to be accessed by words (32-bit).
10.11.1
ADC status register (ADC_SR)
Address offset: 0x00
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
6
5
20
19
18
17
16
Reserved
7
4
3
2
1
0
STRT
JSTRT
JEOC
EOC
AWD
rc_w0
rc_w0
rc_w0
rc_w0
rc_w0
Reserved
Bits 31:5
Reserved, must be kept at reset value.
Bit 4 STRT: Regular channel Start flag
This bit is set by hardware when regular channel conversion starts. It is cleared by software.
0: No regular channel conversion started
1: Regular channel conversion has started
Bit 3 JSTRT: Injected channel Start flag
This bit is set by hardware when injected channel group conversion starts. It is cleared by
software.
0: No injected group conversion started
1: Injected group conversion has started
Bit 2 JEOC: Injected channel end of conversion
This bit is set by hardware at the end of all injected group channel conversion. It is cleared
by software.
0: Conversion is not complete
1: Conversion complete
Bit 1 EOC: End of conversion
This bit is set by hardware at the end of a group channel conversion (regular or injected). It is
cleared by software or by reading the ADC_DR.
0: Conversion is not complete
1: Conversion complete
Bit 0 AWD: Analog watchdog flag
This bit is set by hardware when the converted voltage crosses the values programmed in
the ADC_LTR and ADC_HTR registers. It is cleared by software.
0: No Analog watchdog event occurred
1: Analog watchdog event occurred
Doc ID16188 Rev 5
173/713
187
Analog-to-digital converter (ADC)
10.11.2
RM0041
ADC control register 1 (ADC_CR1)
Address offset: 0x04
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
Reserved
15
14
13
DISCNUM[2:0]
rw
rw
rw
23
22
AWDE
N
JAWDE
N
rw
rw
21
20
19
18
17
16
1
0
rw
rw
Reserved
12
11
10
9
8
7
6
5
JDISCE
N
DISC
EN
JAUTO
AWD
SGL
SCAN
JEOC
IE
AWDIE
EOCIE
rw
rw
rw
rw
rw
rw
rw
rw
4
3
2
AWDCH[4:0]
rw
rw
rw
Bits 31:24 Reserved, must be kept at reset value.
Bit 23 AWDEN: Analog watchdog enable on regular channels
This bit is set/reset by software.
0: Analog watchdog disabled on regular channels
1: Analog watchdog enabled on regular channels
Bit 22 JAWDEN: Analog watchdog enable on injected channels
This bit is set/reset by software.
0: Analog watchdog disabled on injected channels
1: Analog watchdog enabled on injected channels
Bits 21:16
Reserved, must be kept at reset value.
Bits 15:13 DISCNUM[2:0]: Discontinuous mode channel count
These bits are written by software to define the number of regular channels to be converted
in discontinuous mode, after receiving an external trigger.
000: 1 channel
001: 2 channels
.......
111: 8 channels
Bit 12 JDISCEN: Discontinuous mode on injected channels
This bit set and cleared by software to enable/disable discontinuous mode on injected group
channels
0: Discontinuous mode on injected channels disabled
1: Discontinuous mode on injected channels enabled
Bit 11 DISCEN: Discontinuous mode on regular channels
This bit set and cleared by software to enable/disable Discontinuous mode on regular
channels.
0: Discontinuous mode on regular channels disabled
1: Discontinuous mode on regular channels enabled
Bit 10 JAUTO: Automatic Injected Group conversion
This bit set and cleared by software to enable/disable automatic injected group conversion
after regular group conversion.
0: Automatic injected group conversion disabled
1: Automatic injected group conversion enabled
174/713
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
Bit 9 AWDSGL: Enable the watchdog on a single channel in scan mode
This bit set and cleared by software to enable/disable the analog watchdog on the channel
identified by the AWDCH[4:0] bits.
0: Analog watchdog enabled on all channels
1: Analog watchdog enabled on a single channel
Bit 8 SCAN: Scan mode
This bit is set and cleared by software to enable/disable Scan mode. In Scan mode, the
inputs selected through the ADC_SQRx or ADC_JSQRx registers are converted.
0: Scan mode disabled
1: Scan mode enabled
Note: An EOC or JEOC interrupt is generated only on the end of conversion of the last
channel if the corresponding EOCIE or JEOCIE bit is set
Bit 7 JEOCIE: Interrupt enable for injected channels
This bit is set and cleared by software to enable/disable the end of conversion interrupt for
injected channels.
0: JEOC interrupt disabled
1: JEOC interrupt enabled. An interrupt is generated when the JEOC bit is set.
Bit 6 AWDIE: Analog watchdog interrupt enable
This bit is set and cleared by software to enable/disable the analog watchdog interrupt.
0: Analog watchdog interrupt disabled
1: Analog watchdog interrupt enabled
Bit 5 EOCIE: Interrupt enable for EOC
This bit is set and cleared by software to enable/disable the End of Conversion interrupt.
0: EOC interrupt disabled
1: EOC interrupt enabled. An interrupt is generated when the EOC bit is set.
Bits 4:0 AWDCH[4:0]: Analog watchdog channel select bits
These bits are set and cleared by software. They select the input channel to be guarded by
the Analog watchdog.
00000: ADC analog Channel0
00001: ADC analog Channel1
....
01111: ADC analog Channel15
10000: ADC analog Channel16
10001: ADC analog Channel17
Other values reserved.
ADC1 analog Channel16 and Channel17 are internally connected to the temperature
sensor and to VREFINT, respectively.
10.11.3
ADC control register 2 (ADC_CR2)
Address offset: 0x08
Reset value: 0x0000 0000
31
30
29
28
27
Reserved
26
25
24
23
22
21
20
19
TSVRE SWSTA JSWST EXTTR
FE
RT
ART
IG
rw
rw
Doc ID16188 Rev 5
rw
rw
18
17
EXTSEL[2:0]
rw
rw
16
Res.
rw
175/713
187
Analog-to-digital converter (ADC)
15
14
JEXTT
RIG
rw
13
12
JEXTSEL[2:0]
11
ALIGN
RM0041
10
9
Reserved
8
7
6
5
DMA
Reserved
rw
rw
Bits 31:24
rw
rw
Res.
rw
4
3
2
1
0
RST
CAL
CAL
CONT
ADON
rw
rw
rw
rw
Reserved, must be kept at reset value.
Bit 23 TSVREFE: Temperature sensor and VREFINT enable
This bit is set and cleared by software to enable/disable the temperature sensor and VREFINT
channel.
0: Temperature sensor and VREFINT channel disabled
1: Temperature sensor and VREFINT channel enabled
Bit 22 SWSTART: Start conversion of regular channels
This bit is set by software to start conversion and cleared by hardware as soon as
conversion starts. It starts a conversion of a group of regular channels if SWSTART is
selected as trigger event by the EXTSEL[2:0] bits.
0: Reset state
1: Starts conversion of regular channels
Bit 21 JSWSTART: Start conversion of injected channels
This bit is set by software and cleared by software or by hardware as soon as the conversion
starts. It starts a conversion of a group of injected channels (if JSWSTART is selected as
trigger event by the JEXTSEL[2:0] bits.
0: Reset state
1: Starts conversion of injected channels
Bit 20 EXTTRIG: External trigger conversion mode for regular channels
This bit is set and cleared by software to enable/disable the external trigger used to start
conversion of a regular channel group.
0: Conversion on external event disabled
1: Conversion on external event enabled
Bits 19:17 EXTSEL[2:0]: External event select for regular group
These bits select the external event used to trigger the start of conversion of a regular group:
000: Timer 1 CC1 event
001: Timer 1 CC2 event
010: Timer 1 CC3 event
011: Timer 2 CC2 event
100: Timer 3 TRGO event
101: Timer 4 CC4 event
110: EXTI line 11
111: SWSTART
Bit 16
Reserved, must be kept at reset value.
Bit 15 JEXTTRIG: External trigger conversion mode for injected channels
This bit is set and cleared by software to enable/disable the external trigger used to start
conversion of an injected channel group.
0: Conversion on external event disabled
1: Conversion on external event enabled
176/713
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
Bits 14:12 JEXTSEL[2:0]: External event select for injected group
These bits select the external event used to trigger the start of conversion of an injected
group:
000: Timer 1 TRGO event
001: Timer 1 CC4 event
010: Timer 2 TRGO event
011: Timer 2 CC1 event
100: Timer 3 CC4 event
101: Timer 4 TRGO event
110: EXTI line15
111: JSWSTART
Bit 11 ALIGN: Data alignment
This bit is set and cleared by software. Refer to Figure 29.and Figure 30.
0: Right Alignment
1: Left Alignment
Bits 10:9
Reserved, must be kept at reset value.
Bit 8 DMA: Direct memory access mode
This bit is set and cleared by software. Refer to the DMA controller chapter for more details.
0: DMA mode disabled
1: DMA mode enabled
Bits 7:4
Reserved, must be kept at reset value.
Bit 3 RSTCAL: Reset calibration
This bit is set by software and cleared by hardware. It is cleared after the calibration registers
are initialized.
0: Calibration register initialized.
1: Initialize calibration register.
Note: If RSTCAL is set when conversion is ongoing, additional cycles are required to clear the
calibration registers.
Bit 2 CAL: A/D Calibration
This bit is set by software to start the calibration. It is reset by hardware after calibration is
complete.
0: Calibration completed
1: Enable calibration
Bit 1 CONT: Continuous conversion
This bit is set and cleared by software. If set conversion takes place continuously till this bit is
reset.
0: Single conversion mode
1: Continuous conversion mode
Bit 0 ADON: A/D converter ON / OFF
This bit is set and cleared by software. If this bit holds a value of zero and a 1 is written to it
then it wakes up the ADC from Power Down state.
Conversion starts when this bit holds a value of 1 and a 1 is written to it. The application
should allow a delay of tSTAB between power up and start of conversion. Refer to Figure 25.
0: Disable ADC conversion/calibration and go to power down mode.
1: Enable ADC and to start conversion
Note: If any other bit in this register apart from ADON is changed at the same time, then
conversion is not triggered. This is to prevent triggering an erroneous conversion.
Doc ID16188 Rev 5
177/713
187
Analog-to-digital converter (ADC)
10.11.4
RM0041
ADC sample time register 1 (ADC_SMPR1)
Address offset: 0x0C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
Reserved
15
14
SMP
15_0
rw
13
12
11
SMP14[2:0]
rw
rw
10
9
8
SMP13[2:0]
rw
rw
22
21
20
SMP17[2:0]
rw
rw
18
17
16
SMP15[2:1]
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
SMP12[2:0]
rw
19
SMP16[2:0]
rw
SMP11[2:0]
rw
rw
rw
SMP10[2:0]
rw
rw
rw
rw
Bits 31:24 Reserved, must be kept at reset value.
Bits 23:0 SMPx[2:0]: Channel x Sample time selection
These bits are written by software to select the sample time individually for each channel.
During sample cycles channel selection bits must remain unchanged.
000: 1.5 cycles
001: 7.5 cycles
010: 13.5 cycles
011: 28.5 cycles
100: 41.5 cycles
101: 55.5 cycles
110: 71.5 cycles
111: 239.5 cycles
ADC1 analog Channel16 and Channel 17 are internally connected to the temperature
sensor and to VREFINT, respectively.
178/713
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
10.11.5
ADC sample time register 2 (ADC_SMPR2)
Address offset: 0x10
Reset value: 0x0000 0000
31
30
29
Reserved
Res.
15
14
SMP
5_0
rw
28
27
25
24
23
SMP8[2:0]
22
21
20
SMP7[2:0]
19
18
SMP6[2:0]
17
16
SMP5[2:1]
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
13
12
11
10
9
8
7
6
5
4
3
2
1
0
SMP4[2:0]
rw
26
SMP9[2:0]
rw
SMP3[2:0]
rw
rw
rw
SMP2[2:0]
rw
rw
rw
SMP1[2:0]
rw
rw
rw
SMP0[2:0]
rw
rw
rw
rw
Bits 31:30 Reserved, must be kept at reset value.
Bits 29:0 SMPx[2:0]: Channel x Sample time selection
These bits are written by software to select the sample time individually for each channel.
During sample cycles channel selection bits must remain unchanged.
000: 1.5 cycles
001: 7.5 cycles
010: 13.5 cycles
011: 28.5 cycles
100: 41.5 cycles
101: 55.5 cycles
110: 71.5 cycles
111: 239.5 cycles
10.11.6
ADC injected channel data offset register x (ADC_JOFRx) (x=1..4)
Address offset: 0x14-0x20
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
Reserved
7
JOFFSETx[11:0]
Reserved
rw
Bits 31:12
rw
rw
rw
rw
rw
rw
Reserved, must be kept at reset value.
Bits 11:0 JOFFSETx[11:0]: Data offset for injected channel x
These bits are written by software to define the offset to be subtracted from the raw
converted data when converting injected channels. The conversion result can be read from
in the ADC_JDRx registers.
Doc ID16188 Rev 5
179/713
187
Analog-to-digital converter (ADC)
10.11.7
RM0041
ADC watchdog high threshold register (ADC_HTR)
Address offset: 0x24
Reset value: 0x0000 0FFF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
Reserved
15
14
13
12
11
10
9
8
7
HT[11:0]
Reserved
rw
rw
rw
rw
rw
rw
rw
Bits 31:12 Reserved, must be kept at reset value.
Bits 11:0 HT[11:0]: Analog watchdog high threshold
These bits are written by software to define the high threshold for the analog watchdog.
Note:
The software can write to these registers when an ADC conversion is ongoing. The
programmed value will be effective when the next conversion is complete. Writing to this
register is performed with a write delay that can create uncertainty on the effective time at
which the new value is programmed.
10.11.8
ADC watchdog low threshold register (ADC_LTR)
Address offset: 0x28
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
5
4
3
2
1
0
rw
rw
rw
rw
rw
Reserved
15
14
13
12
11
10
9
8
7
6
rw
rw
rw
rw
rw
rw
LT[11:0]
Reserved
rw
Bits 31:12 Reserved, must be kept at reset value.
Bits 11:0 LT[11:0]: Analog watchdog low threshold
These bits are written by software to define the low threshold for the analog watchdog.
Note:
180/713
The software can write to these registers when an ADC conversion is ongoing. The
programmed value will be effective when the next conversion is complete. Writing to this
register is performed with a write delay that can create uncertainty on the effective time at
which the new value is programmed.
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
10.11.9
ADC regular sequence register 1 (ADC_SQR1)
Address offset: 0x2C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
Reserved
15
14
13
rw
rw
SQ16_0
rw
12
11
10
9
8
rw
rw
rw
rw
SQ15[4:0]
rw
21
20
19
18
17
16
SQ16[4:1]
L[3:0]
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
SQ14[4:0]
rw
SQ13[4:0]
rw
Bits 31:24 Reserved, must be kept at reset value.
Bits 23:20 L[3:0]: Regular channel sequence length
These bits are written by software to define the total number of conversions in the regular
channel conversion sequence.
0000: 1 conversion
0001: 2 conversions
.....
1111: 16 conversions
Bits 19:15 SQ16[4:0]: 16th conversion in regular sequence
These bits are written by software with the channel number (0..17) assigned as the 16th in
the conversion sequence.
Bits 14:10 SQ15[4:0]: 15th conversion in regular sequence
Bits 9:5 SQ14[4:0]: 14th conversion in regular sequence
Bits 4:0 SQ13[4:0]: 13th conversion in regular sequence
Doc ID16188 Rev 5
181/713
187
Analog-to-digital converter (ADC)
RM0041
10.11.10 ADC regular sequence register 2 (ADC_SQR2)
Address offset: 0x30
Reset value: 0x0000 0000
31
30
29
28
Reserved
15
14
26
25
24
22
21
20
19
SQ11[4:0]
18
17
16
SQ10[4:1]
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
SQ9[4:0]
rw
23
13
SQ10_
0
rw
27
SQ12[4:0]
rw
Bits 31:30
rw
SQ8[4:0]
rw
rw
rw
rw
rw
SQ7[4:0]
rw
rw
rw
rw
rw
Reserved, must be kept at reset value.
Bits 29:26 SQ12[4:0]: 12th conversion in regular sequence
These bits are written by software with the channel number (0..17) assigned as the 12th in the
sequence to be converted.
Bits 24:20 SQ11[4:0]: 11th conversion in regular sequence
Bits 19:15 SQ10[4:0]: 10th conversion in regular sequence
Bits 14:10 SQ9[4:0]: 9th conversion in regular sequence
Bits 9:5 SQ8[4:0]: 8th conversion in regular sequence
Bits 4:0 SQ7[4:0]: 7th conversion in regular sequence
182/713
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
10.11.11 ADC regular sequence register 3 (ADC_SQR3)
Address offset: 0x34
Reset value: 0x0000 0000
31
30
29
28
Reserved
15
26
25
24
23
22
21
20
19
SQ5[4:0]
18
17
16
SQ4[4:1]
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
SQ4_0
rw
27
SQ6[4:0]
SQ3[4:0]
Bits 31:30
rw
SQ2[4:0]
rw
SQ1[4:0]
rw
Reserved, must be kept at reset value.
Bits 29:25 SQ6[4:0]: 6th conversion in regular sequence
These bits are written by software with the channel number (0..17) assigned as the 6th in the
sequence to be converted.
Bits 24:20 SQ5[4:0]: 5th conversion in regular sequence
Bits 19:15 SQ4[4:0]: 4th conversion in regular sequence
Bits 14:10 SQ3[4:0]: 3rd conversion in regular sequence
Bits 9:5 SQ2[4:0]: 2nd conversion in regular sequence
Bits 4:0 SQ1[4:0]: 1st conversion in regular sequence
Doc ID16188 Rev 5
183/713
187
Analog-to-digital converter (ADC)
RM0041
10.11.12 ADC injected sequence register (ADC_JSQR)
Address offset: 0x38
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
Reserved
15
14
13
rw
rw
JSQ4_0
rw
12
11
10
9
8
rw
rw
rw
rw
JSQ3[4:0]
Bits 31:22
rw
20
19
JL[1:0]
17
16
JSQ4[4:1]
rw
rw
rw
rw
rw
rw
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
7
JSQ2[4:0]
rw
18
JSQ1[4:0]
rw
Reserved, must be kept at reset value.
Bits 21:20 JL[1:0]: Injected sequence length
These bits are written by software to define the total number of conversions in the injected
channel conversion sequence.
00: 1 conversion
01: 2 conversions
10: 3 conversions
11: 4 conversions
Bits 19:15 JSQ4[4:0]: 4th conversion in injected sequence (when JL[1:0] = 3)(1)
These bits are written by software with the channel number (0..17) assigned as the 4th in
the sequence to be converted.
Note: Unlike a regular conversion sequence, if JL[1:0] length is less than four, the channels
are converted in a sequence starting from (4-JL). Example: ADC_JSQR[21:0] = 10
00011 00011 00111 00010 means that a scan conversion will convert the following
channel sequence: 7, 3, 3. (not 2, 7, 3)
Bits 14:10 JSQ3[4:0]: 3rd conversion in injected sequence (when JL[1:0] = 3)
Bits 9:5 JSQ2[4:0]: 2nd conversion in injected sequence (when JL[1:0] = 3)
Bits 4:0 JSQ1[4:0]: 1st conversion in injected sequence (when JL[1:0] = 3)
1. When JL=3 ( 4 injected conversions in the sequencer), the ADC converts the channels in this order:
JSQ1[4:0] >> JSQ2[4:0] >> JSQ3[4:0] >> JSQ4[4:0]
When JL=2 ( 3 injected conversions in the sequencer), the ADC converts the channels in this order:
JSQ2[4:0] >> JSQ3[4:0] >> JSQ4[4:0]
When JL=1 ( 2 injected conversions in the sequencer), the ADC converts the channels in this order:
JSQ3[4:0] >> JSQ4[4:0]
When JL=0 (1 injected conversion in the sequencer), the ADC converts only JSQ4[4:0] channel
184/713
Doc ID16188 Rev 5
RM0041
Analog-to-digital converter (ADC)
10.11.13 ADC injected data register x (ADC_JDRx) (x= 1..4)
Address offset: 0x3C - 0x48
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
r
r
r
r
r
r
r
Reserved
15
14
13
12
11
10
9
8
7
JDATA[15:0]
r
r
r
Bits 31:16
r
r
r
r
r
r
Reserved, must be kept at reset value.
Bits 15:0 JDATA[15:0]: Injected data
These bits are read only. They contain the conversion result from injected channel x. The
data is left or right-aligned as shown in Figure 29 and Figure 30.
10.11.14 ADC regular data register (ADC_DR)
Address offset: 0x4C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
r
r
r
r
r
r
r
Reserved
15
14
13
12
11
10
9
8
7
DATA[15:0]
r
r
r
r
r
r
r
r
r
Bits 31:16 Reserved, must be kept at reset value.
Bits 15:0 DATA[15:0]: Regular data
These bits are read only. They contain the conversion result from the regular channels. The
data is left or right-aligned as shown in Figure 29 and Figure 30.
Doc ID16188 Rev 5
185/713
187
Analog-to-digital converter (ADC)
RM0041
10.11.15 ADC register map
The following table summarizes the ADC registers.
JEOC
EOC
AWD
0
0
0
0
0
0x0C
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ADC_JOFR1
0
0
0
0
0
0
0
0
0
0
0
ADC_JOFR2
186/713
SCAN
JEOC IE
AWDIE
EOCIE
JAUTO
AWD SGL
DMA
Reserved
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
L[3:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
LT[11:0]
Reserved
Reserved
0
HT[11:0]
Reserved
ADC_LTR
0
JOFFSET4[11:0]
Reserved
ADC_HTR
0
JOFFSET3[11:0]
Reserved
ADC_JOFR4
Reset value
0
JOFFSET2[11:0]
Reset value
0x2C
0
Reserved
ADC_JOFR3
ADC_SQR1
0
0
Reset value
0x28
0
JOFFSET1[11:0]
Reset value
0x24
0
Reserved
Reset value
0x20
0
Sample time bits SMPx_x
Reset value
0x1C
0
Sample time bits SMPx_x
Reset value
0x18
0
Reserved
0
ADON
0
DISCEN
EXTSEL
[2:0]
0
JDISCEN
0
JEXTSE
L
[2:0]
ALIGN
0
ADC_SMPR2
Reset value
0x14
0
ADC_SMPR1
Reset value
0x10
0
0
0
AWDCH[4:0]
CAL
Reset value
0
JEXTTRIG
Reserved
0
DISC
NUM
[2:0]
Reserved
Reserved
ADC_CR2
0
EXTTRIG
0x08
0
JSWSTART
Reset value
AWDEN
Reserved
JAWDEN
ADC_CR1
TSVREFE
0x04
SWSTART
Reset value
CONT
Reserved
STRT
ADC_SR
JSTRT
0x00
Register
RSTCAL
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 62. ADC register map and reset values
0
0
0
0
0
0
0
SQ16[4:0] 16th
conversion in
regular
sequence bits
SQ15[4:0] 15th
conversion in
regular
sequence bits
SQ14[4:0] 14th
conversion in
regular
sequence bits
SQ13[4:0] 13th
conversion in
regular
sequence bits
0
0
0
0
0
0
0
Doc ID16188 Rev 5
0
0
0
0
0
0
0
0
0
0
0
0
0
RM0041
Analog-to-digital converter (ADC)
0x30
Register
ADC_SQR2
Reserved
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 62. ADC register map and reset values (continued)
0x34
ADC_SQR3
Reset value
0x38
ADC_JSQR
Reserved
Reset value
SQ12[4:0] 12th
conversion in
regular
sequence bits
SQ11[4:0] 11th
conversion in
regular
sequence bits
SQ10[4:0] 10th
conversion in
regular
sequence bits
0
0
0
0
0
0
0
SQ6[4:0] 6th
conversion in
regular
sequence bits
0
0
0
0
0
0
ADC_JDR1
0
0
SQ5[4:0] 5th
conversion in
regular
sequence bits
0
0
0
0
0
JL[1:
0]
Reserved
Reset value
0x3C
0
0
0
0
0
0
SQ4[4:0] 4th
conversion in
regular
sequence bits
0
0
0
0
ADC_JDR2
0
0
0
0
ADC_JDR3
ADC_JDR4
ADC_DR
0
0
0
SQ3[4:0] 3rd
conversion in
regular
sequence bits
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SQ1[4:0] 1st
conversion in
regular
sequence bits
0
0
0
0
0
JSQ1[4:0] 1st
conversion in
injected
sequence bits
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
JDATA[15:0]
0
0
0
0
0
0
0
0
0
0
JDATA[15:0]
Reserved
0
0
0
0
0
0
0
0
0
0
JDATA[15:0]
Reserved
0
0
0
0
0
0
0
0
0
0
Regular DATA[15:0]
Reserved
Reset value
0
JSQ2[4:0] 2nd
conversion in
injected
sequence bits
JSQ3[4:0] 3rd
conversion in
injected
sequence bits
0
0
SQ2[4:0] 2nd
conversion in
regular
sequence bits
Reserved
Reset value
0x4C
0
SQ7[4:0] 7th
conversion in
regular
sequence bits
JDATA[15:0]
0
Reset value
0x48
0
0
SQ8[4:0] 8th
conversion in
regular
sequence bits
Reserved
Reset value
0x44
0
JSQ4[4:0] 4th
conversion in
injected
sequence bits
Reset value
0x40
0
SQ9[4:0] 9th
conversion in
regular
sequence bits
0
0
0
0
0
0
0
0
0
0
0
Refer to Table 1 on page 36 and Table 2 on page 37 for the register boundary addresses.
Doc ID16188 Rev 5
187/713
187
Digital-to-analog converter (DAC)
11
RM0041
Digital-to-analog converter (DAC)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
11.1
DAC introduction
The DAC module is a 12-bit, voltage output digital-to-analog converter. The DAC can be
configured in 8- or 12-bit mode and may be used in conjunction with the DMA controller. In
12-bit mode, the data could be left- or right-aligned. The DAC has two output channels, each
with its own converter. In dual DAC channel mode, conversions could be done
independently or simultaneously when both channels are grouped together for synchronous
update operations. An input reference pin, VREF+ (shared with ADC) is available for better
resolution.
11.2
DAC main features
•
Two DAC converters: one output channel each
•
Left or right data alignment in 12-bit mode
•
Synchronized update capability
•
Noise-wave generation
•
Triangular-wave generation
•
Dual DAC channel for independent or simultaneous conversions
•
DMA capability for each channel
•
DMA underrun error detection
•
External triggers for conversion
•
Input voltage reference, VREF+
Figure 32 shows the block diagram of a DAC channel and Table 63 gives the pin
description.
188/713
Doc ID16188 Rev 5
RM0041
Digital-to-analog converter (DAC)
Figure 32. DAC channel block diagram
DAC control register
SWTR IGx
TIM6_T RGO
TIM7_T RGO
TIM3_T RGO
TIM2_T RGO
TIM4_T RGO
TIM5_TRGO
or TIM15_TRGO
Trigger selector x
TSELx[2:0] bits
DMAENx
EXTI_9
DM A req ue stx
DHRx
12-bit
Control logicx
LFSRx
trianglex
TENx
MAMPx[3:0] bits
WAVENx[1:0] bits
12-bit
DORx
12-bit
VDDA
DAC_ OU Tx
Digital-to-analog
converterx
VSSA
VR EF+
ai18304
Table 63. DAC pins
Name
Note:
Signal type
Remarks
VREF+
Input, analog reference
positive
The higher/positive reference voltage for the DAC,
2.4 V ≤ VREF+ ≤ VDDA
VDDA
Input, analog supply
Analog power supply
VSSA
Input, analog supply ground
Ground for analog power supply
DAC_OUTx
Analog output signal
DAC channelx analog output
Once the DAC channelx is enabled, the corresponding GPIO pin (PA4 or PA5) is
automatically connected to the analog converter output (DAC_OUTx). In order to avoid
parasitic consumption, the PA4 or PA5 pin should first be configured to analog (AIN).
Doc ID16188 Rev 5
189/713
209
Digital-to-analog converter (DAC)
RM0041
11.3
DAC functional description
11.3.1
DAC channel enable
Each DAC channel can be powered on by setting its corresponding ENx bit in the DAC_CR
register. The DAC channel is then enabled after a startup time tWAKEUP.
Note:
The ENx bit enables the analog DAC Channelx macrocell only. The DAC Channelx digital
interface is enabled even if the ENx bit is reset.
11.3.2
DAC output buffer enable
The DAC integrates two output buffers that can be used to reduce the output impedance,
and to drive external loads directly without having to add an external operational amplifier.
Each DAC channel output buffer can be enabled and disabled using the corresponding
BOFFx bit in the DAC_CR register.
11.3.3
DAC data format
Depending on the selected configuration mode, the data have to be written into the specified
register as described below:
•
Single DAC channelx, there are three possibilities:
–
8-bit right alignment: the software has to load data into the DAC_DHR8Rx [7:0]
bits (stored into the DHRx[11:4] bits)
–
12-bit left alignment: the software has to load data into the DAC_DHR12Lx [15:4]
bits (stored into the DHRx[11:0] bits)
–
12-bit right alignment: the software has to load data into the DAC_DHR12Rx [11:0]
bits (stored into the DHRx[11:0] bits)
Depending on the loaded DAC_DHRyyyx register, the data written by the user is shifted and
stored into the corresponding DHRx (data holding registerx, which are internal non-memorymapped registers). The DHRx register is then loaded into the DORx register either
automatically, by software trigger or by an external event trigger.
190/713
Doc ID16188 Rev 5
RM0041
Digital-to-analog converter (DAC)
Figure 33. Data registers in single DAC channel mode
31
24
15
7
0
8-bit right aligned
12-bit left aligned
12-bit right aligned
ai14710
•
Dual DAC channels, there are three possibilities:
–
8-bit right alignment: data for DAC channel1 to be loaded into the DAC_DHR8RD
[7:0] bits (stored into the DHR1[11:4] bits) and data for DAC channel2 to be loaded
into the DAC_DHR8RD [15:8] bits (stored into the DHR2[11:4] bits)
–
12-bit left alignment: data for DAC channel1 to be loaded into the DAC_DHR12LD
[15:4] bits (stored into the DHR1[11:0] bits) and data for DAC channel2 to be
loaded into the DAC_DHR12LD [31:20] bits (stored into the DHR2[11:0] bits)
–
12-bit right alignment: data for DAC channel1 to be loaded into the
DAC_DHR12RD [11:0] bits (stored into the DHR1[11:0] bits) and data for DAC
channel2 to be loaded into the DAC_DHR12LD [27:16] bits (stored into the
DHR2[11:0] bits)
Depending on the loaded DAC_DHRyyyD register, the data written by the user is shifted
and stored into DHR1 and DHR2 (data holding registers, which are internal non-memorymapped registers). The DHR1 and DHR2 registers are then loaded into the DOR1 and
DOR2 registers, respectively, either automatically, by software trigger or by an external
event trigger.
Figure 34. Data registers in dual DAC channel mode
31
24
15
7
0
8-bit right aligned
12-bit left aligned
12-bit right aligned
ai14709
11.3.4
DAC conversion
The DAC_DORx cannot be written directly and any data transfer to the DAC channelx must
be performed by loading the DAC_DHRx register (write to DAC_DHR8Rx, DAC_DHR12Lx,
DAC_DHR12Rx, DAC_DHR8RD, DAC_DHR12LD or DAC_DHR12LD).
Data stored in the DAC_DHRx register are automatically transferred to the DAC_DORx
register after one APB1 clock cycle, if no hardware trigger is selected (TENx bit in DAC_CR
register is reset). However, when a hardware trigger is selected (TENx bit in DAC_CR
register is set) and a trigger occurs, the transfer is performed three APB1 clock cycles later.
When DAC_DORx is loaded with the DAC_DHRx contents, the analog output voltage
becomes available after a time tSETTLING that depends on the power supply voltage and the
analog output load.
Doc ID16188 Rev 5
191/713
209
Digital-to-analog converter (DAC)
RM0041
Figure 35. Timing diagram for conversion with trigger disabled TEN = 0
APB1_CLK
DHR
DOR
0x1AC
Output voltage
available on DAC_OUT pin
0x1AC
tSETTLING
ai14711b
11.3.5
DAC output voltage
Digital inputs are converted to output voltages on a linear conversion between 0 and VREF+.
The analog output voltages on each DAC channel pin are determined by the following
equation:
DOR
DACoutput = V REF × -------------4095
11.3.6
DAC trigger selection
If the TENx control bit is set, conversion can then be triggered by an external event (timer
counter, external interrupt line). The TSELx[2:0] control bits determine which out of 8
possible events will trigger conversion as shown in Table 64.
Table 64. External triggers
Source
Type
TSEL[2:0]
Timer 6 TRGO event
000
Timer 3 TRGO event
001
Timer 7 TRGO event
Timer 5 or Timer 15 TRGO
event
Internal signal from on-chip
timers
010
011
Timer 2 TRGO event
100
Timer 4 TRGO event
101
EXTI line9
External pin
110
SWTRIG
Software control bit
111
Each time a DAC interface detects a rising edge on the selected timer TRGO output, or on
the selected external interrupt line 9, the last data stored into the DAC_DHRx register are
transferred into the DAC_DORx register. The DAC_DORx register is updated three APB1
cycles after the trigger occurs.
If the software trigger is selected, the conversion starts once the SWTRIG bit is set.
SWTRIG is reset by hardware once the DAC_DORx register has been loaded with the
DAC_DHRx register contents.
192/713
Doc ID16188 Rev 5
RM0041
Note:
Digital-to-analog converter (DAC)
TSELx[2:0] bit cannot be changed when the ENx bit is set.
When software trigger is selected, the transfer from the DAC_DHRx register to the
DAC_DORx register takes only one APB1 clock cycle.
For High-density value line devices, the TIM15 TRGO event is selected as DAC Trigger 3
only if the MISC_REMAP bit in the AFIO_MAPR2 register is set and DAC Trigger 3 is
connected to TIM5 TRGO when the MISC_REMAP bit in the AFIO_MAPR2 register is reset.
On low- and medium -density devices the TIM15 TRGO event is always selected as DAC
Trigger 3. For more details refer to the Section 7.3: Alternate function I/O and debug
configuration (AFIO) on page 115.
11.3.7
DMA request
Each DAC channel has a DMA capability. Two DMA channels are used to service DAC
channel DMA requests.
A DAC DMA request is generated when an external trigger (but not a software trigger)
occurs while the DMAENx bit is set. The value of the DAC_DHRx register is then transferred
into the DAC_DORx register.
In dual mode, if both DMAENx bits are set, two DMA requests are generated. If only one
DMA request is needed, the user should set only the corresponding DMAENx bit. In this
way, the application can manage both DAC channels in dual mode by using one DMA
request and a unique DMA channel.
DMA underrun
The DAC DMA request is not queued so that if a second external trigger arrives before the
acknowledgement for the first external trigger is received (first request), then no new
request is issued and the DMA channelx underrun flag DMAUDRx in the DAC_SR register
is set, reporting the error condition. DMA data transfers are then disabled and no further
DMA request is treated. The DAC channelx continues to convert old data.
The software should clear the DMAUDRx flag by writing “1”, clear the DMAEN bit of the
used DMA stream and re-initialize both DMA and DAC channelx to restart the transfer
correctly. The software should modify the DAC trigger conversion frequency or lighten the
DMA workload to avoid a new DMA underrun. Finally, the DAC conversion could be
resumed by enabling both DMA data transfer and conversion trigger.
For each DAC channelx, an interrupt is also generated if its corresponding DMAUDRIEx bit
in the DAC_CR register is enabled.
11.3.8
Noise generation
In order to generate a variable-amplitude pseudonoise, an LFSR (linear feedback shift
register) is available. DAC noise generation is selected by setting WAVEx[1:0] to “01”. The
preloaded value in LFSR is 0xAAA. This register is updated three APB1 clock cycles after
each trigger event, following a specific calculation algorithm.
Doc ID16188 Rev 5
193/713
209
Digital-to-analog converter (DAC)
RM0041
Figure 36. DAC LFSR register calculation algorithm
XOR
X6
X 12
11
10
9
8
7
6
X4
5
4
X0
X
3
2
1
0
12
NOR
ai14713b
The LFSR value, that may be masked partially or totally by means of the MAMPx[3:0] bits in
the DAC_CR register, is added up to the DAC_DHRx contents without overflow and this
value is then stored into the DAC_DORx register.
If LFSR is 0x0000, a ‘1 is injected into it (antilock-up mechanism).
It is possible to reset LFSR wave generation by resetting the WAVEx[1:0] bits.
Figure 37. DAC conversion (SW trigger enabled) with LFSR wave generation
APB1_CLK
DHR
0x00
0xAAA
DOR
0xD55
SWTRIG
ai14714
Note:
The DAC trigger must be enabled for noise generation by setting the TENx bit in the
DAC_CR register.
11.3.9
Triangle-wave generation
It is possible to add a small-amplitude triangular waveform on a DC or slowly varying signal.
DAC triangle-wave generation is selected by setting WAVEx[1:0] to “10”. The amplitude is
configured through the MAMPx[3:0] bits in the DAC_CR register. An internal triangle counter
is incremented three APB1 clock cycles after each trigger event. The value of this counter is
then added to the DAC_DHRx register without overflow and the sum is stored into the
DAC_DORx register. The triangle counter is incremented as long as it is less than the
maximum amplitude defined by the MAMPx[3:0] bits. Once the configured amplitude is
reached, the counter is decremented down to 0, then incremented again and so on.
It is possible to reset triangle wave generation by resetting the WAVEx[1:0] bits.
194/713
Doc ID16188 Rev 5
RM0041
Digital-to-analog converter (DAC)
Figure 38. DAC triangle wave generation
N
T IO
EN
M
)N
N
TIO
TA
CR
E
EN
EM
CR
TA
$E
-!-0X;=MAXAMPLITUDE
$!#?$(2XBASEVALUE
$!#?$(2XBASEVALUE
AIC
Figure 39. DAC conversion (SW trigger enabled) with triangle wave generation
APB1_CLK
DHR
DOR
0xABE
0xABE
0xABF
0xAC0
SWTRIG
ai14714
Note:
The DAC trigger must be enabled for noise generation by setting the TENx bit in the
DAC_CR register.
The MAMPx[3:0] bits must be configured before enabling the DAC, otherwise they cannot
be changed.
11.4
Dual DAC channel conversion
To efficiently use the bus bandwidth in applications that require the two DAC channels at the
same time, three dual registers are implemented: DHR8RD, DHR12RD and DHR12LD. A
unique register access is then required to drive both DAC channels at the same time.
Eleven possible conversion modes are possible using the two DAC channels and these dual
registers. All the conversion modes can nevertheless be obtained using separate DHRx
registers if needed.
All modes are described in the paragraphs below.
11.4.1
Independent trigger without wave generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure different trigger sources by setting different values in the TSEL1[2:0] and
TSEL2[2:0] bits
•
Load the dual DAC channel data into the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
Doc ID16188 Rev 5
195/713
209
Digital-to-analog converter (DAC)
RM0041
When a DAC channel1 trigger arrives, the DHR1 register is transferred into DAC_DOR1
(three APB1 clock cycles later).
When a DAC channel2 trigger arrives, the DHR2 register is transferred into DAC_DOR2
(three APB1 clock cycles later).
11.4.2
Independent trigger with single LFSR generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure different trigger sources by setting different values in the TSEL1[2:0] and
TSEL2[2:0] bits
•
Configure the two DAC channel WAVEx[1:0] bits as “01” and the same LFSR mask
value in the MAMPx[3:0] bits
•
Load the dual DAC channel data into the desired DHR register (DHR12RD, DHR12LD
or DHR8RD)
When a DAC channel1 trigger arrives, the LFSR1 counter, with the same mask, is added to
the DHR1 register and the sum is transferred into DAC_DOR1 (three APB1 clock cycles
later). Then the LFSR1 counter is updated.
When a DAC channel2 trigger arrives, the LFSR2 counter, with the same mask, is added to
the DHR2 register and the sum is transferred into DAC_DOR2 (three APB1 clock cycles
later). Then the LFSR2 counter is updated.
11.4.3
Independent trigger with different LFSR generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure different trigger sources by setting different values in the TSEL1[2:0] and
TSEL2[2:0] bits
•
Configure the two DAC channel WAVEx[1:0] bits as “01” and set different LFSR masks
values in the MAMP1[3:0] and MAMP2[3:0] bits
•
Load the dual DAC channel data into the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
When a DAC channel1 trigger arrives, the LFSR1 counter, with the mask configured by
MAMP1[3:0], is added to the DHR1 register and the sum is transferred into DAC_DOR1
(three APB1 clock cycles later). Then the LFSR1 counter is updated.
When a DAC channel2 trigger arrives, the LFSR2 counter, with the mask configured by
MAMP2[3:0], is added to the DHR2 register and the sum is transferred into DAC_DOR2
(three APB1 clock cycles later). Then the LFSR2 counter is updated.
196/713
Doc ID16188 Rev 5
RM0041
11.4.4
Digital-to-analog converter (DAC)
Independent trigger with single triangle generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure different trigger sources by setting different values in the TSEL1[2:0] and
TSEL2[2:0] bits
•
Configure the two DAC channel WAVEx[1:0] bits as “1x” and the same maximum
amplitude value in the MAMPx[3:0] bits
•
Load the dual DAC channel data into the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
When a DAC channel1 trigger arrives, the DAC channel1 triangle counter, with the same
triangle amplitude, is added to the DHR1 register and the sum is transferred into
DAC_DOR1 (three APB1 clock cycles later). The DAC channel1 triangle counter is then
updated.
When a DAC channel2 trigger arrives, the DAC channel2 triangle counter, with the same
triangle amplitude, is added to the DHR2 register and the sum is transferred into
DAC_DOR2 (three APB1 clock cycles later). The DAC channel2 triangle counter is then
updated.
11.4.5
Independent trigger with different triangle generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure different trigger sources by setting different values in the TSEL1[2:0] and
TSEL2[2:0] bits
•
Configure the two DAC channel WAVEx[1:0] bits as “1x” and set different maximum
amplitude values in the MAMP1[3:0] and MAMP2[3:0] bits
•
Load the dual DAC channel data into the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
When a DAC channel1 trigger arrives, the DAC channel1 triangle counter, with a triangle
amplitude configured by MAMP1[3:0], is added to the DHR1 register and the sum is
transferred into DAC_DOR1 (three APB1 clock cycles later). The DAC channel1 triangle
counter is then updated.
When a DAC channel2 trigger arrives, the DAC channel2 triangle counter, with a triangle
amplitude configured by MAMP2[3:0], is added to the DHR2 register and the sum is
transferred into DAC_DOR2 (three APB1 clock cycles later). The DAC channel2 triangle
counter is then updated.
11.4.6
Simultaneous software start
To configure the DAC in this conversion mode, the following sequence is required:
•
Load the dual DAC channel data to the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
In this configuration, one APB1 clock cycle later, the DHR1 and DHR2 registers are
transferred into DAC_DOR1 and DAC_DOR2, respectively.
Doc ID16188 Rev 5
197/713
209
Digital-to-analog converter (DAC)
11.4.7
RM0041
Simultaneous trigger without wave generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure the same trigger source for both DAC channels by setting the same value in
the TSEL1[2:0] and TSEL2[2:0] bits
•
Load the dual DAC channel data to the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
When a trigger arrives, the DHR1 and DHR2 registers are transferred into DAC_DOR1 and
DAC_DOR2, respectively (after three APB1 clock cycles).
11.4.8
Simultaneous trigger with single LFSR generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure the same trigger source for both DAC channels by setting the same value in
the TSEL1[2:0] and TSEL2[2:0] bits
•
Configure the two DAC channel WAVEx[1:0] bits as “01” and the same LFSR mask
value in the MAMPx[3:0] bits
•
Load the dual DAC channel data to the desired DHR register (DHR12RD, DHR12LD or
DHR8RD)
When a trigger arrives, the LFSR1 counter, with the same mask, is added to the DHR1
register and the sum is transferred into DAC_DOR1 (three APB1 clock cycles later). The
LFSR1 counter is then updated. At the same time, the LFSR2 counter, with the same mask,
is added to the DHR2 register and the sum is transferred into DAC_DOR2 (three APB1
clock cycles later). The LFSR2 counter is then updated.
11.4.9
Simultaneous trigger with different LFSR generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure the same trigger source for both DAC channels by setting the same value in
the TSEL1[2:0] and TSEL2[2:0] bits
•
Configure the two DAC channel WAVEx[1:0] bits as “01” and set different LFSR mask
values using the MAMP1[3:0] and MAMP2[3:0] bits
•
Load the dual DAC channel data into the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
When a trigger arrives, the LFSR1 counter, with the mask configured by MAMP1[3:0], is
added to the DHR1 register and the sum is transferred into DAC_DOR1 (three APB1 clock
cycles later). The LFSR1 counter is then updated.
At the same time, the LFSR2 counter, with the mask configured by MAMP2[3:0], is added to
the DHR2 register and the sum is transferred into DAC_DOR2 (three APB1 clock cycles
later). The LFSR2 counter is then updated.
198/713
Doc ID16188 Rev 5
RM0041
11.4.10
Digital-to-analog converter (DAC)
Simultaneous trigger with single triangle generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure the same trigger source for both DAC channels by setting the same value in
the TSEL1[2:0] and TSEL2[2:0] bits
•
Configure the two DAC channel WAVEx[1:0] bits as “1x” and the same maximum
amplitude value using the MAMPx[3:0] bits
•
Load the dual DAC channel data into the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
When a trigger arrives, the DAC channel1 triangle counter, with the same triangle
amplitude, is added to the DHR1 register and the sum is transferred into DAC_DOR1 (three
APB1 clock cycles later). The DAC channel1 triangle counter is then updated.
At the same time, the DAC channel2 triangle counter, with the same triangle amplitude, is
added to the DHR2 register and the sum is transferred into DAC_DOR2 (three APB1 clock
cycles later). The DAC channel2 triangle counter is then updated.
11.4.11
Simultaneous trigger with different triangle generation
To configure the DAC in this conversion mode, the following sequence is required:
•
Set the two DAC channel trigger enable bits TEN1 and TEN2
•
Configure the same trigger source for both DAC channels by setting the same value in
the TSEL1[2:0] and TSEL2[2:0] bits
•
Configure the two DAC channel WAVEx[1:0] bits as “1x” and set different maximum
amplitude values in the MAMP1[3:0] and MAMP2[3:0] bits
•
Load the dual DAC channel data into the desired DHR register (DAC_DHR12RD,
DAC_DHR12LD or DAC_DHR8RD)
When a trigger arrives, the DAC channel1 triangle counter, with a triangle amplitude
configured by MAMP1[3:0], is added to the DHR1 register and the sum is transferred into
DAC_DOR1 (three APB1 clock cycles later). Then the DAC channel1 triangle counter is
updated.
At the same time, the DAC channel2 triangle counter, with a triangle amplitude configured
by MAMP2[3:0], is added to the DHR2 register and the sum is transferred into DAC_DOR2
(three APB1 clock cycles later). Then the DAC channel2 triangle counter is updated.
Doc ID16188 Rev 5
199/713
209
Digital-to-analog converter (DAC)
11.5
RM0041
DAC registers
Refer to Section: List of abbreviations for registers for a list of abbreviations used in register
descriptions.
The peripheral registers have to be accessed by words (32 bits).
11.5.1
DAC control register (DAC_CR)
Address offset: 0x00
Reset value: 0x0000 0000
31
30
Reserved
15
14
Reserved
29
28
DMAU
DRIE2
DMA
EN2
27
26
25
24
MAMP2[3:0]
23
22
21
WAVE2[1:0]
20
19
TSEL2[2:0]
18
17
16
TEN2
BOFF2
EN2
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
13
12
11
10
9
8
7
6
5
4
3
2
1
0
DMAU
DRIE1
DMA
EN1
TEN1
BOFF1
EN1
rw
rw
rw
rw
rw
MAMP1[3:0]
rw
rw
rw
WAVE1[1:0]
rw
rw
rw
TSEL1[2:0]
rw
rw
rw
Bits 31:30 Reserved, must be kept at reset value.
Bits 29 DMAUDRIE2: DAC channel2 DMA underrun interrupt enable
This bit is set and cleared by software.
0: DAC channel2 DMA underrun interrupt disabled
1: DAC channel2 DMA underrun interrupt enabled
Bit 28 DMAEN2: DAC channel2 DMA enable
This bit is set and cleared by software.
0: DAC channel2 DMA mode disabled
1: DAC channel2 DMA mode enabled
Bits 27:24 MAMP2[3:0]: DAC channel2 mask/amplitude selector
These bits are written by software to select mask in wave generation mode or amplitude in
triangle generation mode.
0000: Unmask bit0 of LFSR/ triangle amplitude equal to 1
0001: Unmask bits[1:0] of LFSR/ triangle amplitude equal to 3
0010: Unmask bits[2:0] of LFSR/ triangle amplitude equal to 7
0011: Unmask bits[3:0] of LFSR/ triangle amplitude equal to 15
0100: Unmask bits[4:0] of LFSR/ triangle amplitude equal to 31
0101: Unmask bits[5:0] of LFSR/ triangle amplitude equal to 63
0110: Unmask bits[6:0] of LFSR/ triangle amplitude equal to 127
0111: Unmask bits[7:0] of LFSR/ triangle amplitude equal to 255
1000: Unmask bits[8:0] of LFSR/ triangle amplitude equal to 511
1001: Unmask bits[9:0] of LFSR/ triangle amplitude equal to 1023
1010: Unmask bits[10:0] of LFSR/ triangle amplitude equal to 2047
≥ 1011: Unmask bits[11:0] of LFSR/ triangle amplitude equal to 4095
Bits 23:22 WAVE2[1:0]: DAC channel2 noise/triangle wave generation enable
These bits are set/reset by software.
00: wave generation disabled
01: Noise wave generation enabled
1x: Triangle wave generation enabled
Note: Only used if bit TEN2 = 1 (DAC channel2 trigger enabled)
200/713
Doc ID16188 Rev 5
RM0041
Digital-to-analog converter (DAC)
Bits 21:19 TSEL2[2:0]: DAC channel2 trigger selection
These bits select the external event used to trigger DAC channel2
000: Timer 6 TRGO event
001: Timer 3 TRGO event
010: Timer 7 TRGO event
011: Timer 5 or timer 15 TRGO event
100: Timer 2 TRGO event
101: Timer 4 TRGO event
110: External line9
111: Software trigger
Note: Only used if bit TEN2 = 1 (DAC channel2 trigger enabled).
For high-density value line devices, the TIM15 TRGO event is selected as DAC Trigger
3 only if the MISC_REMAP bit in the AFIO_MAPR2 register is set and DAC Trigger 3 is
connected to TIM5 TRGO when the MISC_REMAP bit in the AFIO_MAPR2 register is
reset. On low- and medium -density devices the TIM15 TRGO event is always selected
as DAC Trigger 3. For more details refer to the AFIO section.
Bit 18 TEN2: DAC channel2 trigger enable
This bit is set and cleared by software to enable/disable DAC channel2 trigger
0: DAC channel2 trigger disabled and data written into the DAC_DHRx register are
transferred one APB1 clock cycle later to the DAC_DOR2 register
1: DAC channel2 trigger enabled and data from the DAC_DHRx register are transferred
three APB1 clock cycles later to the DAC_DOR2 register
Note: When software trigger is selected, the transfer from the DAC_DHRx register to the
DAC_DOR2 register takes only one APB1 clock cycle.
Bit 17 BOFF2: DAC channel2 output buffer disable
This bit is set and cleared by software to enable/disable DAC channel2 output buffer.
0: DAC channel2 output buffer enabled
1: DAC channel2 output buffer disabled
Bit 16 EN2: DAC channel2 enable
This bit is set and cleared by software to enable/disable DAC channel2.
0: DAC channel2 disabled
1: DAC channel2 enabled
Bits 15:14 Reserved, must be kept at reset value.
Bit 13 DMAUDRIE1: DAC channel1 DMA Underrun Interrupt enable
This bit is set and cleared by software.
0: DAC channel1 DMA Underrun Interrupt disabled
1: DAC channel1 DMA Underrun Interrupt enabled
Bit 12 DMAEN1: DAC channel1 DMA enable
This bit is set and cleared by software.
0: DAC channel1 DMA mode disabled
1: DAC channel1 DMA mode enabled
Doc ID16188 Rev 5
201/713
209
Digital-to-analog converter (DAC)
RM0041
Bits 11:8 MAMP1[3:0]: DAC channel1 mask/amplitude selector
These bits are written by software to select mask in wave generation mode or amplitude in
triangle generation mode.
0000: Unmask bit0 of LFSR/ triangle amplitude equal to 1
0001: Unmask bits[1:0] of LFSR/ triangle amplitude equal to 3
0010: Unmask bits[2:0] of LFSR/ triangle amplitude equal to 7
0011: Unmask bits[3:0] of LFSR/ triangle amplitude equal to 15
0100: Unmask bits[4:0] of LFSR/ triangle amplitude equal to 31
0101: Unmask bits[5:0] of LFSR/ triangle amplitude equal to 63
0110: Unmask bits[6:0] of LFSR/ triangle amplitude equal to 127
0111: Unmask bits[7:0] of LFSR/ triangle amplitude equal to 255
1000: Unmask bits[8:0] of LFSR/ triangle amplitude equal to 511
1001: Unmask bits[9:0] of LFSR/ triangle amplitude equal to 1023
1010: Unmask bits[10:0] of LFSR/ triangle amplitude equal to 2047
≥ 1011: Unmask bits[11:0] of LFSR/ triangle amplitude equal to 4095
Bits 7:6 WAVE1[1:0]: DAC channel1 noise/triangle wave generation enable
These bits are set and cleared by software.
00: wave generation disabled
01: Noise wave generation enabled
1x: Triangle wave generation enabled
Note: Only used if bit TEN1 = 1 (DAC channel1 trigger enabled).
Bits 5:3 TSEL1[2:0]: DAC channel1 trigger selection
These bits select the external event used to trigger DAC channel1.
000: Timer 6 TRGO event
001: Timer 3 TRGO event
010: Timer 7 TRGO event
011: Timer 5 or Timer 15 TRGO event
100: Timer 2 TRGO event
101: Timer 4 TRGO event
110: External line9
111: Software trigger
Note: Only used if bit TEN1 = 1 (DAC channel1 trigger enabled).
Bit 2 TEN1: DAC channel1 trigger enable
This bit is set and cleared by software to enable/disable DAC channel1 trigger.
0: DAC channel1 trigger disabled and data written into the DAC_DHRx register are
transferred one APB1 clock cycle later to the DAC_DOR1 register
1: DAC channel1 trigger enabled and data from the DAC_DHRx register are transferred
three APB1 clock cycles later to the DAC_DOR1 register
Note: When software trigger is selected, the transfer from the DAC_DHRx register to the
DAC_DOR1 register takes only one APB1 clock cycle.
Bit 1 BOFF1: DAC channel1 output buffer disable
This bit is set and cleared by software to enable/disable DAC channel1 output buffer.
0: DAC channel1 output buffer enabled
1: DAC channel1 output buffer disabled
Bit 0 EN1: DAC channel1 enable
This bit is set and cleared by software to enable/disable DAC channel1.
0: DAC channel1 disabled
1: DAC channel1 enabled
202/713
Doc ID16188 Rev 5
RM0041
Digital-to-analog converter (DAC)
11.5.2
DAC software trigger register (DAC_SWTRIGR)
Address offset: 0x04
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
6
5
4
3
2
17
16
1
0
Reserved
15
14
13
12
11
10
9
8
7
SWTRIG2 SWTRIG1
Reserved
w
w
Bits 31:2 Reserved, must be kept at reset value.
Bit 1 SWTRIG2: DAC channel2 software trigger
This bit is set and cleared by software to enable/disable the software trigger.
0: Software trigger disabled
1: Software trigger enabled
Note: This bit is cleared by hardware (one APB1 clock cycle later) once the DAC_DHR2
register value has been loaded into the DAC_DOR2 register.
Bit 0 SWTRIG1: DAC channel1 software trigger
This bit is set and cleared by software to enable/disable the software trigger.
0: Software trigger disabled
1: Software trigger enabled
Note: This bit is cleared by hardware (one APB1 clock cycle later) once the DAC_DHR1
register value has been loaded into the DAC_DOR1 register.
11.5.3
DAC channel1 12-bit right-aligned data holding register
(DAC_DHR12R1)
Address offset: 0x08
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
Reserved
15
14
13
Reserved
12
11
10
9
8
7
rw
rw
rw
rw
rw
DACC1DHR[11:0]
rw
rw
Bits 31:12 Reserved, must be kept at reset value.
Bits 11:0 DACC1DHR[11:0]: DAC channel1 12-bit right-aligned data
These bits are written by software which specifies 12-bit data for DAC channel1.
Doc ID16188 Rev 5
203/713
209
Digital-to-analog converter (DAC)
11.5.4
RM0041
DAC channel1 12-bit left aligned data holding register
(DAC_DHR12L1)
Address offset: 0x0C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
3
2
1
0
Reserved
15
14
13
12
11
10
9
8
7
6
5
4
rw
rw
rw
rw
rw
DACC1DHR[11:0]
rw
rw
rw
rw
rw
rw
rw
Reserved
Bits 31:16 Reserved, must be kept at reset value.
Bits 15:4 DACC1DHR[11:0]: DAC channel1 12-bit left-aligned data
These bits are written by software which specifies 12-bit data for DAC channel1.
Bits 3:0 Reserved, must be kept at reset value.
11.5.5
DAC channel1 8-bit right aligned data holding register
(DAC_DHR8R1)
Address offset: 0x10
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
6
5
20
19
18
17
16
4
3
2
1
0
rw
rw
rw
Reserved
15
14
13
12
11
Reserved
10
9
8
7
DACC1DHR[7:0]
rw
rw
rw
rw
rw
Bits 31:8 Reserved, must be kept at reset value.
Bits 7:0 DACC1DHR[7:0]: DAC channel1 8-bit right-aligned data
These bits are written by software which specifies 8-bit data for DAC channel1.
204/713
Doc ID16188 Rev 5
RM0041
Digital-to-analog converter (DAC)
11.5.6
DAC channel2 12-bit right aligned data holding register
(DAC_DHR12R2)
Address offset: 0x14
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
Reserved
15
14
13
12
11
10
9
8
7
DACC2DHR[11:0]
Reserved
rw
rw
rw
rw
rw
rw
rw
Bits 31:12 Reserved, must be kept at reset value.
Bits 11:0 DACC2DHR[11:0]: DAC channel2 12-bit right-aligned data
These bits are written by software which specifies 12-bit data for DAC channel2.
11.5.7
DAC channel2 12-bit left aligned data holding register
(DAC_DHR12L2)
Address offset: 0x18
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
rw
23
22
21
20
19
18
17
16
7
6
5
4
3
2
1
0
rw
rw
rw
rw
Reserved
DACC2DHR[11:0]
rw
rw
rw
rw
rw
rw
rw
Reserved
Bits 31:16 Reserved, must be kept at reset value.
Bits 15:4 DACC2DHR[11:0]: DAC channel2 12-bit left-aligned data
These bits are written by software which specify 12-bit data for DAC channel2.
Bits 3:0 Reserved, must be kept at reset value.
11.5.8
DAC channel2 8-bit right-aligned data holding register
(DAC_DHR8R2)
Address offset: 0x1C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
6
5
20
19
18
17
16
4
3
2
1
0
rw
rw
rw
Reserved
Reserved
7
DACC2DHR[7:0]
rw
rw
rw
rw
rw
Bits 31:8 Reserved, must be kept at reset value.
Bits 7:0 DACC2DHR[7:0]: DAC channel2 8-bit right-aligned data
These bits are written by software which specifies 8-bit data for DAC channel2.
Doc ID16188 Rev 5
205/713
209
Digital-to-analog converter (DAC)
11.5.9
RM0041
Dual DAC 12-bit right-aligned data holding register
(DAC_DHR12RD)
Address offset: 0x20
Reset value: 0x0000 0000
31
30
29
28
14
13
26
25
24
23
22
21
20
19
18
17
16
DACC2DHR[11:0]
Reserved
15
27
12
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
17
16
DACC1DHR[11:0]
Reserved
rw
rw
rw
rw
rw
rw
rw
Bits 31:28 Reserved, must be kept at reset value.
Bits 27:16 DACC2DHR[11:0]: DAC channel2 12-bit right-aligned data
These bits are written by software which specifies 12-bit data for DAC channel2.
Bits 15:12 Reserved, must be kept at reset value.
Bits 11:0 DACC1DHR[11:0]: DAC channel1 12-bit right-aligned data
These bits are written by software which specifies 12-bit data for DAC channel1.
11.5.10
DUAL DAC 12-bit left aligned data holding register
(DAC_DHR12LD)
Address offset: 0x24
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
DACC2DHR[11:0]
rw
rw
rw
rw
rw
15
14
13
12
11
rw
rw
rw
rw
rw
rw
rw
10
9
8
7
6
5
4
rw
rw
rw
rw
rw
DACC1DHR[11:0]
rw
rw
rw
rw
rw
rw
rw
18
Reserved
3
2
Reserved
Bits 31:20 DACC2DHR[11:0]: DAC channel2 12-bit left-aligned data
These bits are written by software which specifies 12-bit data for DAC channel2.
Bits 19:16 Reserved, must be kept at reset value.
Bits 15:4 DACC1DHR[11:0]: DAC channel1 12-bit left-aligned data
These bits are written by software which specifies 12-bit data for DAC channel1.
Bits 3:0 Reserved, must be kept at reset value.
206/713
Doc ID16188 Rev 5
1
0
RM0041
Digital-to-analog converter (DAC)
11.5.11
DUAL DAC 8-bit right aligned data holding register
(DAC_DHR8RD)
Address offset: 0x28
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
6
5
20
19
18
17
16
4
3
2
1
0
rw
rw
rw
Reserved
15
14
13
12
11
10
9
8
7
DACC2DHR[7:0]
rw
rw
rw
rw
rw
DACC1DHR[7:0]
rw
rw
rw
rw
rw
rw
rw
rw
Bits 31:16 Reserved, must be kept at reset value.
Bits 15:8 DACC2DHR[7:0]: DAC channel2 8-bit right-aligned data
These bits are written by software which specifies 8-bit data for DAC channel2.
Bits 7:0 DACC1DHR[7:0]: DAC channel1 8-bit right-aligned data
These bits are written by software which specifies 8-bit data for DAC channel1.
11.5.12
DAC channel1 data output register (DAC_DOR1)
Address offset: 0x2C
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
r
r
r
r
r
Reserved
7
DACC1DOR[11:0]
Reserved
r
r
r
r
r
r
r
Bits 31:12 Reserved, must be kept at reset value.
Bit 11:0 DACC1DOR[11:0]: DAC channel1 data output
These bits are read-only, they contain data output for DAC channel1.
11.5.13
DAC channel2 data output register (DAC_DOR2)
Address offset: 0x30
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
r
r
r
r
r
Reserved
15
14
13
Reserved
12
11
10
9
8
7
DACC2DOR[11:0]
r
r
r
r
r
r
r
Bits 31:12 Reserved, must be kept at reset value.
Bits 11:0 DACC2DOR[11:0]: DAC channel2 data output
These bits are read-only, they contain data output for DAC channel2.
Doc ID16188 Rev 5
207/713
209
Digital-to-analog converter (DAC)
11.5.14
RM0041
DAC status register (DAC_SR)
Address offset: 0x34
Reset value: 0x0000 0000
31
30
Reserved
15
29
27
26
25
24
23
22
21
20
19
18
17
16
5
4
3
2
1
0
Reserved
rc_w1
14
Reserved
28
DMAUDR2
13
12
11
10
9
8
7
6
DMAUDR1
Reserved
rc_w1
Bits 31:30 Reserved, must be kept at reset value.
Bit 29 DMAUDR2: DAC channel2 DMA underrun flag
This bit is set by hardware and cleared by software (by writing it to 1).
0: No DMA underrun error condition occurred for DAC channel2
1: DMA underrun error condition occurred for DAC channel2 (the currently selected trigger is
driving DAC channel2 conversion at a frequency higher than the DMA service capability rate)
Bits 28:14 Reserved, must be kept at reset value.
Bit 13 DMAUDR1: DAC channel1 DMA underrun flag
This bit is set by hardware and cleared by software (by writing it to 1).
0: No DMA underrun error condition occurred for DAC channel1
1: DMA underrun error condition occurred for DAC channel1 (the currently selected trigger is
driving DAC channel1 conversion at a frequency higher than the DMA service capability rate)
Bits 12:0 Reserved, must be kept at reset value.
11.5.15
DAC register map
Table 65 summarizes the DAC registers.
208/713
Reserved
Reserved
Reserved
Reserved
1
0
EN1
SWTRIG1
Reserved
DACC1DHR[7:0]
DACC2DHR[11:0]
DACC2DHR[11:0]
Doc ID16188 Rev 5
2
DACC1DHR[11:0]
DACC1DHR[11:0]
Reserved
BOFF1
Reserved
SWTRIG2
3
WAVE TSEL1[2
1[2:0]
:0]
TEN1
4
5
6
7
8
11
MAMP1[3:0]
9
12
10
13
DMAEN1
14
16
DMAUDRIE1
17
EN2
15
18
BOFF2
Reserved
19
TSEL2[2:0]
TEN2
DAC_
DHR12L2
20
0x18
WAVE
2[2:0]
21
DAC_
DHR12R2
22
0x14
MAMP2[3:0]
23
DAC_
DHR8R1
24
0x10
25
DAC_
DHR12L1
26
0x0C
27
DAC_
DHR12R1
28
0x08
29
DAC_
SWTRIGR
DMAEN2
0x04
30
DAC_CR
DMAUDRIE2
0x00
Reserved
Offset
31
Table 65. DAC register map
Register
name
Reserved
RM0041
Digital-to-analog converter (DAC)
Reserved
DACC2DHR[11:0]
Reserved
Reserved
DACC2DHR[11:0]
DMAUDR2
Reserved
Reserved
0
1
3
4
5
6
DACC1DHR[11:0]
DACC1DHR[11:0]
DACC2DHR[7:0]
Reserved
7
DACC2DHR[7:0]
DMAUDR1
Reserved
8
9
11
10
12
DAC_SR
13
0x34
14
DACC2DOR[11:0]
15
Reserved
16
DAC_
DOR2
17
0x30
18
DACC1DOR[11:0]
19
Reserved
20
DAC_
DOR1
21
0x2C
22
DAC_
DHR8RD
23
0x28
24
DAC_
DHR12LD
25
0x24
26
DAC_
DHR12RD
27
0x20
28
DAC_
DHR8R2
29
0x1C
30
Register
name
31
Offset
2
Table 65. DAC register map (continued)
Reserved
DACC1DHR[7:0]
Reserved
Refer to Section: Memory map for the register boundary addresses.
Doc ID16188 Rev 5
209/713
209
Advanced-control timer (TIM1)
12
RM0041
Advanced-control timer (TIM1)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
12.1
TIM1 introduction
The advanced-control timers (TIM1) consist of a 16-bit auto-reload counter driven by a
programmable prescaler.
It may be used for a variety of purposes, including measuring the pulse lengths of input
signals (input capture) or generating output waveforms (output compare, PWM,
complementary PWM with dead-time insertion).
Pulse lengths and waveform periods can be modulated from a few microseconds to several
milliseconds using the timer prescaler and the RCC clock controller prescalers.
The advanced-control (TIM1) and general-purpose (TIMx) timers are completely
independent, and do not share any resources. They can be synchronized together as
described in Section 12.3.20.
210/713
Doc ID16188 Rev 5
RM0041
12.2
Advanced-control timer (TIM1)
TIM1 main features
TIM1 timer features include:
•
16-bit up, down, up/down auto-reload counter.
•
16-bit programmable prescaler allowing dividing (also “on the fly”) the counter clock
frequency either by any factor between 1 and 65536.
•
Up to 4 independent channels for:
–
Input Capture
–
Output Compare
–
PWM generation (Edge and Center-aligned Mode)
–
One-pulse mode output
•
Complementary outputs with programmable dead-time
•
Synchronization circuit to control the timer with external signals and to interconnect
several timers together.
•
Repetition counter to update the timer registers only after a given number of cycles of
the counter.
•
Break input to put the timer’s output signals in reset state or in a known state.
•
Interrupt/DMA generation on the following events:
–
Update: counter overflow/underflow, counter initialization (by software or
internal/external trigger)
–
Trigger event (counter start, stop, initialization or count by internal/external trigger)
–
Input capture
–
Output compare
–
Break input
•
Supports incremental (quadrature) encoder and hall-sensor circuitry for positioning
purposes
•
Trigger input for external clock or cycle-by-cycle current management
Doc ID16188 Rev 5
211/713
281
Advanced-control timer (TIM1)
RM0041
7,0[B(75
Figure 40. Advanced-control timer block diagram
&.B7,0IURP5&&
(75
,QWHUQDOFORFN&.B,17
7ULJJHU
FRQWUROOHU
(75)
3RODULW\VHOHFWLRQ
(GJHGHWHFWRUDQG3UHVFDOHU
(753
75*2
7RRWKHUWLPHUV
7R'$&DQG$'&
,QSXWILOWHU
,75
7*,
,75
75*,
,75
,75
6ODYHPRGH
FRQWUROOHU
7,)B('
5(35HJLVWHU
&17
FRXQWHU
'7*>@UHJLVWHUV
&&,
7,)3
,QSXWILOWHU
(GJHGHWHFWRU
,&
3UHVFDOHU
7,)3
7,0[B&+
75&
7,
,QSXWILOWHU
(GJHGHWHFWRU
7,)3
&&,
,&
3UHVFDOHU
7,0[B&+
7,
,QSXWILOWHU
(GJHGHWHFWRU
7,)3
7,0[B&+
7,)3
7,
,QSXWILOWHU
(GJHGHWHFWRU
&&,
,&
3UHVFDOHU
75&
7,)3
3UHVFDOHU
7,)3
7,0[B%.,1
3RODULW\VHOHFWLRQ
&&,
&DSWXUH&RPSDUH 2&5()
5HJLVWHU
2&1
8
&&,
2&
&DSWXUH&RPSDUH 2&5()
5HJLVWHU
8
&&,
,&36
&DSWXUH&RPSDUH 2&5()
5HJLVWHU
8
75&
%5.
8
,&36
&&,
,&
&DSWXUH&RPSDUH 2&5()
5HJLVWHU
,&36
7,)3
75&
&&,
,&36
2&
7,
2&
%,
&ORFNIDLOXUHHYHQWIURPFORFNFRQWUROOHU
&66&ORFN6HFXULW\6\VWHP
,QWHUUXSW'0$RXWSXW
/HJHQG
5HJ
(YHQW
'7*
7,0[B&+
&.B&17
2&1
7,0[B&+
36&
SUHVFDOHU
7,0[B&+1
5HSHWLWLRQFRXQWHU
&.B36&
7,0[B&+1
2&
$XWR5HORDG
5HJLVWHU
7,0[B&+1 7,0[B&+
8
7,0[B&+
8
7,0[B&+
(QFRGHU
LQWHUIDFH
7,)3
8,
2&1
7,)3
5HVHW
(QDEOH
8S'RZQ
&RXQW
2XWSXWFRQWURO
3UHORDGUHJLVWHUVWUDQVIHUUHGWRDFWLYHUHJLVWHUVRQ8HYHQWDFFRUGLQJWRFRQWUROELW
069
212/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
12.3
TIM1 functional description
12.3.1
Time-base unit
The main block of the programmable advanced-control timer is a 16-bit counter with its
related auto-reload register. The counter can count up, down or both up and down. The
counter clock can be divided by a prescaler.
The counter, the auto-reload register and the prescaler register can be written or read by
software. This is true even when the counter is running.
The time-base unit includes:
•
Counter register (TIMx_CNT)
•
Prescaler register (TIMx_PSC)
•
Auto-reload register (TIMx_ARR)
•
Repetition counter register (TIMx_RCR)
The auto-reload register is preloaded. Writing to or reading from the auto-reload register
accesses the preload register. The content of the preload register are transferred into the
shadow register permanently or at each update event (UEV), depending on the auto-reload
preload enable bit (ARPE) in TIMx_CR1 register. The update event is sent when the counter
reaches the overflow (or underflow when downcounting) and if the UDIS bit equals 0 in the
TIMx_CR1 register. It can also be generated by software. The generation of the update
event is described in detailed for each configuration.
The counter is clocked by the prescaler output CK_CNT, which is enabled only when the
counter enable bit (CEN) in TIMx_CR1 register is set (refer also to the slave mode controller
description to get more details on counter enabling).
Note that the counter starts counting 1 clock cycle after setting the CEN bit in the TIMx_CR1
register.
Prescaler description
The prescaler can divide the counter clock frequency by any factor between 1 and 65536. It
is based on a 16-bit counter controlled through a 16-bit register (in the TIMx_PSC register).
It can be changed on the fly as this control register is buffered. The new prescaler ratio is
taken into account at the next update event.
Figure 41 and Figure 42 give some examples of the counter behavior when the prescaler
ratio is changed on the fly:
Doc ID16188 Rev 5
213/713
281
Advanced-control timer (TIM1)
RM0041
Figure 41. Counter timing diagram with prescaler division change from 1 to 2
&.B36&
&(1
7LPHUFORFN
&.B&17
&RXQWHUUHJLVWHU
)
)
)
)$ )% )&
8SGDWHHYHQW8(9
3UHVFDOHUFRQWUROUHJLVWHU
:ULWHDQHZYDOXHLQ7,0[B36&
3UHVFDOHUEXIIHU
3UHVFDOHUFRXQWHU
069
Figure 42. Counter timing diagram with prescaler division change from 1 to 4
&.B36&
&(1
7LPHUFORFN
&.B&17
&RXQWHUUHJLVWHU
)
)
)
)$ )% )&
8SGDWHHYHQW8(9
3UHVFDOHUFRQWUROUHJLVWHU
:ULWHDQHZYDOXHLQ7,0[B36&
3UHVFDOHUEXIIHU
3UHVFDOHUFRXQWHU
069
214/713
Doc ID16188 Rev 5
RM0041
12.3.2
Advanced-control timer (TIM1)
Counter modes
Upcounting mode
In upcounting mode, the counter counts from 0 to the auto-reload value (content of the
TIMx_ARR register), then restarts from 0 and generates a counter overflow event.
If the repetition counter is used, the update event (UEV) is generated after upcounting is
repeated for the number of times programmed in the repetition counter register plus one
(TIMx_RCR+1). Else the update event is generated at each counter overflow.
Setting the UG bit in the TIMx_EGR register (by software or by using the slave mode
controller) also generates an update event.
The UEV event can be disabled by software by setting the UDIS bit in the TIMx_CR1
register. This is to avoid updating the shadow registers while writing new values in the
preload registers. Then no update event occurs until the UDIS bit has been written to 0.
However, the counter restarts from 0, as well as the counter of the prescaler (but the
prescale rate does not change). In addition, if the URS bit (update request selection) in
TIMx_CR1 register is set, setting the UG bit generates an update event UEV but without
setting the UIF flag (thus no interrupt or DMA request is sent). This is to avoid generating
both update and capture interrupts when clearing the counter on the capture event.
When an update event occurs, all the registers are updated and the update flag (UIF bit in
TIMx_SR register) is set (depending on the URS bit):
•
The repetition counter is reloaded with the content of TIMx_RCR register,
•
The auto-reload shadow register is updated with the preload value (TIMx_ARR),
•
The buffer of the prescaler is reloaded with the preload value (content of the TIMx_PSC
register).
The following figures show some examples of the counter behavior for different clock
frequencies when TIMx_ARR=0x36.
Figure 43. Counter timing diagram, internal clock divided by 1
<ͺW^
EdͺE
dŝŵĞƌĐůŽĐŬс<ͺEd
ŽƵŶƚĞƌƌĞŐŝƐƚĞƌ
ϯϭ
ϯϮ
ϯϯ
ϯϰ
ϯϱ
ϯϲ
ϬϬ
Ϭϭ
ϬϮ
Ϭϯ
Ϭϰ
Ϭϱ
Ϭϲ
Ϭϳ
ŽƵŶƚĞƌŽǀĞƌĨůŽǁ
hƉĚĂƚĞĞǀĞŶƚ;hsͿ
hƉĚĂƚĞŝŶƚĞƌƌƵƉƚĨůĂŐ;h/&Ϳ
069
Doc ID16188 Rev 5
215/713
281
Advanced-control timer (TIM1)
RM0041
Figure 44. Counter timing diagram, internal clock divided by 2
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 45. Counter timing diagram, internal clock divided by 4
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 46. Counter timing diagram, internal clock divided by N
&.B36&
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
216/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Figure 47. Counter timing diagram, update event when ARPE=0 (TIMx_ARR not
preloaded)
<ͺW^
E
dŝŵĞƌĐůŽĐŬс<ͺEd
ŽƵŶƚĞƌƌĞŐŝƐƚĞƌ
ϯϭ
ϯϯ
ϯϮ
ϯϰ
ϯϱ
ϯϲ
ϬϬ
Ϭϭ
ϬϮ
Ϭϯ
Ϭϰ
Ϭϱ
Ϭϲ
Ϭϳ
ŽƵŶƚĞƌŽǀĞƌĨůŽǁ
hƉĚĂƚĞĞǀĞŶƚ;hsͿ
hƉĚĂƚĞŝŶƚĞƌƌƵƉƚĨůĂŐ;h/&Ϳ
ƵƚŽͲƌĞůŽĂĚƉƌĞůŽĂĚƌĞŐŝƐƚĞƌ
&&
ϯϲ
tƌŝƚĞĂŶĞǁǀĂůƵĞŝŶd/DdžͺZZ
069
Figure 48. Counter timing diagram, update event when ARPE=1 (TIMx_ARR
preloaded)
&.B36&
&(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
)
)
)
) )
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ
8,)
$XWRUHORDGSUHORDG
UHJLVWHU
)
$XWRUHORDGVKDGRZ
UHJLVWHU
)
:ULWHDQHZYDOXHLQ7,0[B$55
Doc ID16188 Rev 5
069
217/713
281
Advanced-control timer (TIM1)
RM0041
Downcounting mode
In downcounting mode, the counter counts from the auto-reload value (content of the
TIMx_ARR register) down to 0, then restarts from the auto-reload value and generates a
counter underflow event.
If the repetition counter is used, the update event (UEV) is generated after downcounting is
repeated for the number of times programmed in the repetition counter register plus one
(TIMx_RCR+1). Else the update event is generated at each counter underflow.
Setting the UG bit in the TIMx_EGR register (by software or by using the slave mode
controller) also generates an update event.
The UEV update event can be disabled by software by setting the UDIS bit in TIMx_CR1
register. This is to avoid updating the shadow registers while writing new values in the
preload registers. Then no update event occurs until UDIS bit has been written to 0.
However, the counter restarts from the current auto-reload value, whereas the counter of the
prescaler restarts from 0 (but the prescale rate doesn’t change).
In addition, if the URS bit (update request selection) in TIMx_CR1 register is set, setting the
UG bit generates an update event UEV but without setting the UIF flag (thus no interrupt or
DMA request is sent). This is to avoid generating both update and capture interrupts when
clearing the counter on the capture event.
When an update event occurs, all the registers are updated and the update flag (UIF bit in
TIMx_SR register) is set (depending on the URS bit):
•
The repetition counter is reloaded with the content of TIMx_RCR register
•
The buffer of the prescaler is reloaded with the preload value (content of the TIMx_PSC
register)
•
The auto-reload active register is updated with the preload value (content of the
TIMx_ARR register). Note that the auto-reload is updated before the counter is
reloaded, so that the next period is the expected one
The following figures show some examples of the counter behavior for different clock
frequencies when TIMx_ARR=0x36.
218/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Figure 49. Counter timing diagram, internal clock divided by 1
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHUXQGHUIORZ
FQWBXGI
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ
8,)
069
Figure 50. Counter timing diagram, internal clock divided by 2
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ
8,)
069
Doc ID16188 Rev 5
219/713
281
Advanced-control timer (TIM1)
RM0041
Figure 51. Counter timing diagram, internal clock divided by 4
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 52. Counter timing diagram, internal clock divided by N
&.B36&
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ
8,)
069
220/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Figure 53. Counter timing diagram, update event when repetition counter is not used
&.B36&
&(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ
8,)
$XWRUHORDGSUHORDG
UHJLVWHU
))
:ULWHDQHZYDOXHLQ7,0[B$55
069
Center-aligned mode (up/down counting)
In center-aligned mode, the counter counts from 0 to the auto-reload value (content of the
TIMx_ARR register) – 1, generates a counter overflow event, then counts from the autoreload value down to 1 and generates a counter underflow event. Then it restarts counting
from 0.
Center-aligned mode is active when the CMS bits in TIMx_CR1 register are not equal to
'00'. The Output compare interrupt flag of channels configured in output is set when: the
counter counts down (Center aligned mode 1, CMS = "01"), the counter counts up (Center
aligned mode 2, CMS = "10") the counter counts up and down (Center aligned mode 3,
CMS = "11").
In this mode, the DIR direction bit in the TIMx_CR1 register cannot be written. It is updated
by hardware and gives the current direction of the counter.
The update event can be generated at each counter overflow and at each counter underflow
or by setting the UG bit in the TIMx_EGR register (by software or by using the slave mode
controller) also generates an update event. In this case, the counter restarts counting from
0, as well as the counter of the prescaler.
The UEV update event can be disabled by software by setting the UDIS bit in the TIMx_CR1
register. This is to avoid updating the shadow registers while writing new values in the
preload registers. Then no update event occurs until UDIS bit has been written to 0.
However, the counter continues counting up and down, based on the current auto-reload
value.
In addition, if the URS bit (update request selection) in TIMx_CR1 register is set, setting the
UG bit generates an UEV update event but without setting the UIF flag (thus no interrupt or
DMA request is sent). This is to avoid generating both update and capture interrupts when
clearing the counter on the capture event.
Doc ID16188 Rev 5
221/713
281
Advanced-control timer (TIM1)
RM0041
When an update event occurs, all the registers are updated and the update flag (UIF bit in
TIMx_SR register) is set (depending on the URS bit):
•
The repetition counter is reloaded with the content of TIMx_RCR register
•
The buffer of the prescaler is reloaded with the preload value (content of the TIMx_PSC
register)
•
The auto-reload active register is updated with the preload value (content of the
TIMx_ARR register). Note that if the update source is a counter overflow, the autoreload is updated before the counter is reloaded, so that the next period is the expected
one (the counter is loaded with the new value).
The following figures show some examples of the counter behavior for different clock
frequencies.
Figure 54. Counter timing diagram, internal clock divided by 1, TIMx_ARR = 0x6
&.B36&
&(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
1. Here, center-aligned mode 1 is used (for more details refer to Section 12.4: TIM1 registers).
Figure 55. Counter timing diagram, internal clock divided by 2
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
222/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Figure 56. Counter timing diagram, internal clock divided by 4, TIMx_ARR=0x36
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
1.
Center-aligned mode 2 or 3 is used with an UIF on overflow.
Figure 57. Counter timing diagram, internal clock divided by N
&.B36&
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Doc ID16188 Rev 5
223/713
281
Advanced-control timer (TIM1)
RM0041
Figure 58. Counter timing diagram, update event with ARPE=1 (counter underflow)
&.B36&
&(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGSUHORDGUHJLVWHU
)'
:ULWHDQHZYDOXHLQ7,0[B$55
$XWRUHORDGDFWLYHUHJLVWHU
)'
069
Figure 59. Counter timing diagram, Update event with ARPE=1 (counter overflow)
&.B36&
&(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
)
)
)$
)% )& )
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGSUHORDGUHJLVWHU
)'
:ULWHDQHZYDOXHLQ7,0[B$55
$XWRUHORDGDFWLYHUHJLVWHU
)'
069
12.3.3
Repetition counter
Section 12.3.1: Time-base unit describes how the update event (UEV) is generated with
respect to the counter overflows/underflows. It is actually generated only when the repetition
counter has reached zero. This can be useful when generating PWM signals.
This means that data are transferred from the preload registers to the shadow registers
(TIMx_ARR auto-reload register, TIMx_PSC prescaler register, but also TIMx_CCRx
capture/compare registers in compare mode) every N+1 counter overflows or underflows,
where N is the value in the TIMx_RCR repetition counter register.
224/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
The repetition counter is decremented:
•
At each counter overflow in upcounting mode,
•
At each counter underflow in downcounting mode,
•
At each counter overflow and at each counter underflow in center-aligned mode.
Although this limits the maximum number of repetition to 128 PWM cycles, it makes it
possible to update the duty cycle twice per PWM period. When refreshing compare
registers only once per PWM period in center-aligned mode, maximum resolution is
2xTck, due to the symmetry of the pattern.
The repetition counter is an auto-reload type; the repetition rate is maintained as defined by
the TIMx_RCR register value (refer to Figure 60). When the update event is generated by
software (by setting the UG bit in TIMx_EGR register) or by hardware through the slave
mode controller, it occurs immediately whatever the value of the repetition counter is and the
repetition counter is reloaded with the content of the TIMx_RCR register.
In center-aligned mode, for odd values of RCR, the update event occurs either on the
overflow or on the underflow depending on when the RCR register was written and when
the counter was started. If the RCR was written before starting the counter, the UEV occurs
on the overflow. If the RCR was written after starting the counter, the UEV occurs on the
underflow. For example for RCR = 3, the UEV is generated on each 4th overflow or
underflow event depending on when RCR was written.
Figure 60. Update rate examples depending on mode and TIMx_RCR register settings
(GJHDOLJQHGPRGH
&RXQWHUDOLJQHGPRGH
8SFRXQWLQJ
&RXQWHU
7,0[B&17
7,0[B5&5 7,0[B5&5 7,0[B5&5 7,0[B5&5 7,0[B5&5 DQG
UHV\QFKURQL]DWLRQ
8(9
8(9
8(9
8(9
8(9
E\6:
8(9
'RZQFRXQWLQJ
E\6:
E\6:
8SGDWHHYHQW3UHORDGUHJLVWHUVWUDQVIHUUHGWRDFWLYHUHJLVWHUVDQGXSGDWHLQWHUUXSWJHQHUDWHG
8SGDWH(YHQWLIWKHUHSHWLWLRQFRXQWHUXQGHUIORZRFFXUVZKHQWKHFRXQWHULVHTXDOWRWKHDXWRUHORDGYDOXH
06Y9
Doc ID16188 Rev 5
225/713
281
Advanced-control timer (TIM1)
12.3.4
RM0041
Clock selection
The counter clock can be provided by the following clock sources:
•
Internal clock (CK_INT)
•
External clock mode1: external input pin
•
External clock mode2: external trigger input ETR
•
Internal trigger inputs (ITRx): using one timer as prescaler for another timer, for
example, the user can configure Timer 1 to act as a prescaler for Timer 2. Refer to
Using one timer as prescaler for another timer for more details.
Internal clock source (CK_INT)
If the slave mode controller is disabled (SMS=000), then the CEN, DIR (in the TIMx_CR1
register) and UG bits (in the TIMx_EGR register) are actual control bits and can be changed
only by software (except UG which remains cleared automatically). As soon as the CEN bit
is written to 1, the prescaler is clocked by the internal clock CK_INT.
Figure 61 shows the behavior of the control circuit and the upcounter in normal mode,
without prescaler.
Figure 61. Control circuit in normal mode, internal clock divided by 1
,QWHUQDOFORFN
&(1 &17B(1
8*
&17B,1,7
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
069
External clock source mode 1
This mode is selected when SMS=111 in the TIMx_SMCR register. The counter can count at
each rising or falling edge on a selected input.
226/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Figure 62. TI2 external clock connection example
7,0[B60&5
76>@
RU 7,)
7,)
,75[
7,B('
7,
)LOWHU
(GJH
GHWHFWRU
7,)B5LVLQJ
7,)B)DOOLQJ
7,)3
7,)3
(75)
RU
RU
[[
75*,
(75)
&.B,17
,&)>@
&&3
7,0[B&&05
7,0[B&&(5
LQWHUQDOFORFN
(QFRGHU
PRGH
([WHUQDOFORFN
PRGH
([WHUQDOFORFN
PRGH
&.B36&
,QWHUQDOFORFN
PRGH
(&(
606>@
7,0[B60&5
069
For example, to configure the upcounter to count in response to a rising edge on the TI2
input, use the following procedure:
Note:
1.
Configure channel 2 to detect rising edges on the TI2 input by writing CC2S = ‘01’ in
the TIMx_CCMR1 register.
2.
Configure the input filter duration by writing the IC2F[3:0] bits in the TIMx_CCMR1
register (if no filter is needed, keep IC2F=0000).
3.
Select rising edge polarity by writing CC2P=0 in the TIMx_CCER register.
4.
Configure the timer in external clock mode 1 by writing SMS=111 in the TIMx_SMCR
register.
5.
Select TI2 as the trigger input source by writing TS=110 in the TIMx_SMCR register.
6.
Enable the counter by writing CEN=1 in the TIMx_CR1 register.
The capture prescaler is not used for triggering, so the user does not need to configure it.
When a rising edge occurs on TI2, the counter counts once and the TIF flag is set.
The delay between the rising edge on TI2 and the actual clock of the counter is due to the
resynchronization circuit on TI2 input.
Doc ID16188 Rev 5
227/713
281
Advanced-control timer (TIM1)
RM0041
Figure 63. Control circuit in external clock mode 1
7,
&17B(1
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
:ULWH7,) 069
External clock source mode 2
This mode is selected by writing ECE=1 in the TIMx_SMCR register.
The counter can count at each rising or falling edge on the external trigger input ETR.
Figure 64 gives an overview of the external trigger input block.
Figure 64. External trigger input block
RU 7,)
7,)
(75
RU
RU
75*,
(75SLQ
'LYLGHU
(753
I'76
)LOWHU
GRZQFRXQWHU
(75)
&.B,17
(73
(736>@
(7)>@
7,0[B60&5
7,0[B60&5
7,0[B60&5
LQWHUQDOFORFN
(QFRGHU
PRGH
([WHUQDOFORFN
PRGH
([WHUQDOFORFN
PRGH
&.B36&
,QWHUQDOFORFN
PRGH
(&(
606>@
7,0[B60&5
069
228/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
For example, to configure the upcounter to count each 2 rising edges on ETR, use the
following procedure:
1.
As no filter is needed in this example, write ETF[3:0]=0000 in the TIMx_SMCR register.
2.
Set the prescaler by writing ETPS[1:0]=01 in the TIMx_SMCR register
3.
Select rising edge detection on the ETR pin by writing ETP=0 in the TIMx_SMCR
register
4.
Enable external clock mode 2 by writing ECE=1 in the TIMx_SMCR register.
5.
Enable the counter by writing CEN=1 in the TIMx_CR1 register.
The counter counts once each 2 ETR rising edges.
The delay between the rising edge on ETR and the actual clock of the counter is due to the
resynchronization circuit on the ETRP signal.
Figure 65. Control circuit in external clock mode 2
I &.B,17
&17B(1
(75
(753
(75)
&RXQWHUFORFN &.B,17 &.B36&
&RXQWHUUHJLVWHU
069
12.3.5
Capture/compare channels
Each Capture/Compare channel is built around a capture/compare register (including a
shadow register), a input stage for capture (with digital filter, multiplexing and prescaler) and
an output stage (with comparator and output control).
Figure 66 to Figure 69 give an overview of one Capture/Compare channel.
The input stage samples the corresponding TIx input to generate a filtered signal TIxF.
Then, an edge detector with polarity selection generates a signal (TIxFPx) which can be
used as trigger input by the slave mode controller or as the capture command. It is
prescaled before the capture register (ICxPS).
Doc ID16188 Rev 5
229/713
281
Advanced-control timer (TIM1)
RM0041
Figure 66. Capture/compare channel (example: channel 1 input stage)
7,)B('
7RWKHVODYHPRGHFRQWUROOHU
7,)B5LVLQJ
7,
)LOWHU
7,)
GRZQFRXQWHU
I'76
(GJH
GHWHFWRU
7,)B)DOOLQJ
7,)3
7,)3
&&3&&13
,&)>@
75&
7,0[B&&(5
7,0[B&&05
7,)B5LVLQJ
IURPFKDQQHO
7,)B)DOOLQJ
IURPFKDQQHO
IURPVODYHPRGH
FRQWUROOHU
,&36
'LYLGHU
,&
&&6>@ ,&36>@
&&(
7,0[B&&05
7,0[B&&(5
069
The output stage generates an intermediate waveform which is then used for reference:
OCxRef (active high). The polarity acts at the end of the chain.
Figure 67. Capture/compare channel 1 main circuit
$3%%XV
5HDG&&5+ 6
5HDG&&5/
KLJK
UHDGBLQBSURJUHVV
&&6>@
,&36
ZULWHBLQBSURJUHVV
,QSXW
PRGH
6 ZULWH&&5+
&DSWXUHFRPSDUHSUHORDGUHJLVWHU
5
5
FRPSDUHBWUDQVIHU
FDSWXUHBWUDQVIHU
&&6>@
ORZ
LIELW
0&8SHULSKHUDOLQWHUIDFH
2XWSXW
PRGH
&17!&&5
&RXQWHU
&&*
&&6>@
8(9
&RPSDUDWRU
&&(
&&6>@
2&3(
&DSWXUHFRPSDUHVKDGRZUHJLVWHU
&DSWXUH
ZULWH&&5/
IURPWLPH
EDVHXQLW
2&3(
7,0B&&05
&17 &&5
7,0B(*5
069
230/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Figure 68. Output stage of capture/compare channel (channel 1 to 3)
7RWKHPDVWHUPRGH
FRQWUROOHU
(75)
µ¶
2&5()
&17!&&5 2XWSXW
PRGH
&17 &&5
FRQWUROOHU
2&5()&
2&B'7
2XWSXW
VHOHFWRU
'HDGWLPH
JHQHUDWRU
&&3
2&
2XWSXW
HQDEOH
FLUFXLW
2&1
7,0B&&(5
2&1B'7
µ¶
2&[5()
2&5()
[
2XWSXW
HQDEOH
FLUFXLW
[
&&1( &&( 7,0B&&(5
2&&( 2&0>@
'7*>@
&&1( &&(
&&13
02( 266, 2665
7,0B&&05
7,0B%'75
7,0B&&(5
7,0B&&(5
7,0B%'75
069
Figure 69. Output stage of capture/compare channel (channel 4)
7RWKHPDVWHU
PRGHFRQWUROOHU
(75
&17!&&5
&17!&&5
2XWSXW
PRGH
FRQWUROOHU
2XWSXW
HQDEOH
FLUFXLW
2&
&&3
2&5()
7,0B&&(5
&&(
02(
2&0>@
7,0B&&05
266,
2,6
7,0B&&(5
7,0B%'75
7,0B&5
069
The capture/compare block is made of one preload register and one shadow register. Write
and read always access the preload register.
In capture mode, captures are actually done in the shadow register, which is copied into the
preload register.
In compare mode, the content of the preload register is copied into the shadow register
which is compared to the counter.
Doc ID16188 Rev 5
231/713
281
Advanced-control timer (TIM1)
12.3.6
RM0041
Input capture mode
In Input capture mode, the Capture/Compare Registers (TIMx_CCRx) are used to latch the
value of the counter after a transition detected by the corresponding ICx signal. When a
capture occurs, the corresponding CCXIF flag (TIMx_SR register) is set and an interrupt or
a DMA request can be sent if they are enabled. If a capture occurs while the CCxIF flag was
already high, then the over-capture flag CCxOF (TIMx_SR register) is set. CCxIF can be
cleared by software by writing it to ‘0’ or by reading the captured data stored in the
TIMx_CCRx register. CCxOF is cleared when written to ‘0’.
The following example shows how to capture the counter value in TIMx_CCR1 when TI1
input rises. To do this, use the following procedure:
•
Select the active input: TIMx_CCR1 must be linked to the TI1 input, so write the CC1S
bits to 01 in the TIMx_CCMR1 register. As soon as CC1S becomes different from 00,
the channel is configured in input and the TIMx_CCR1 register becomes read-only.
•
Program the needed input filter duration with respect to the signal connected to the
timer (by programming ICxF bits in the TIMx_CCMRx register if the input is a TIx input).
Let’s imagine that, when toggling, the input signal is not stable during at must five
internal clock cycles. We must program a filter duration longer than these five clock
cycles. We can validate a transition on TI1 when 8 consecutive samples with the new
level have been detected (sampled at fDTS frequency). Then write IC1F bits to 0011 in
the TIMx_CCMR1 register.
•
Select the edge of the active transition on the TI1 channel by writing CC1P bit to 0 in
the TIMx_CCER register (rising edge in this case).
•
Program the input prescaler. In our example, we wish the capture to be performed at
each valid transition, so the prescaler is disabled (write IC1PS bits to ‘00’ in the
TIMx_CCMR1 register).
•
Enable capture from the counter into the capture register by setting the CC1E bit in the
TIMx_CCER register.
•
If needed, enable the related interrupt request by setting the CC1IE bit in the
TIMx_DIER register, and/or the DMA request by setting the CC1DE bit in the
TIMx_DIER register.
When an input capture occurs:
•
The TIMx_CCR1 register gets the value of the counter on the active transition.
•
CC1IF flag is set (interrupt flag). CC1OF is also set if at least two consecutive captures
occurred whereas the flag was not cleared.
•
An interrupt is generated depending on the CC1IE bit.
•
A DMA request is generated depending on the CC1DE bit.
In order to handle the overcapture, it is recommended to read the data before the
overcapture flag. This is to avoid missing an overcapture which could happen after reading
the flag and before reading the data.
Note:
232/713
IC interrupt and/or DMA requests can be generated by software by setting the
corresponding CCxG bit in the TIMx_EGR register.
Doc ID16188 Rev 5
RM0041
12.3.7
Advanced-control timer (TIM1)
PWM input mode
This mode is a particular case of input capture mode. The procedure is the same except:
•
Two ICx signals are mapped on the same TIx input.
•
These 2 ICx signals are active on edges with opposite polarity.
•
One of the two TIxFP signals is selected as trigger input and the slave mode controller
is configured in reset mode.
For example, user can measure the period (in TIMx_CCR1 register) and the duty cycle (in
TIMx_CCR2 register) of the PWM applied on TI1 using the following procedure (depending
on CK_INT frequency and prescaler value):
•
Select the active input for TIMx_CCR1: write the CC1S bits to 01 in the TIMx_CCMR1
register (TI1 selected).
•
Select the active polarity for TI1FP1 (used both for capture in TIMx_CCR1 and counter
clear): write the CC1P bit to ‘0’ (active on rising edge).
•
Select the active input for TIMx_CCR2: write the CC2S bits to 10 in the TIMx_CCMR1
register (TI1 selected).
•
Select the active polarity for TI1FP2 (used for capture in TIMx_CCR2): write the CC2P
bit to ‘1’ (active on falling edge).
•
Select the valid trigger input: write the TS bits to 101 in the TIMx_SMCR register
(TI1FP1 selected).
•
Configure the slave mode controller in reset mode: write the SMS bits to 100 in the
TIMx_SMCR register.
•
Enable the captures: write the CC1E and CC2E bits to ‘1’ in the TIMx_CCER register.
Figure 70. PWM input mode timing
TI1
TIMx_CNT
0004
0000
0001
0002
TIMx_CCR1
0004
TIMx_CCR2
0002
IC1 capture
IC2 capture
reset counter
0003
0004
IC2 capture
pulse width
measurement
0000
IC1 capture
period
measurement
ai15413
12.3.8
Forced output mode
In output mode (CCxS bits = 00 in the TIMx_CCMRx register), each output compare signal
(OCxREF and then OCx/OCxN) can be forced to active or inactive level directly by software,
independently of any comparison between the output compare register and the counter.
To force an output compare signal (OCXREF/OCx) to its active level, the user just needs to
write 101 in the OCxM bits in the corresponding TIMx_CCMRx register. Thus OCXREF is
Doc ID16188 Rev 5
233/713
281
Advanced-control timer (TIM1)
RM0041
forced high (OCxREF is always active high) and OCx get opposite value to CCxP polarity
bit.
For example: CCxP=0 (OCx active high) => OCx is forced to high level.
The OCxREF signal can be forced low by writing the OCxM bits to 100 in the TIMx_CCMRx
register.
Anyway, the comparison between the TIMx_CCRx shadow register and the counter is still
performed and allows the flag to be set. Interrupt and DMA requests can be sent
accordingly. This is described in the output compare mode section below.
12.3.9
Output compare mode
This function is used to control an output waveform or indicating when a period of time has
elapsed.
When a match is found between the capture/compare register and the counter, the output
compare function:
•
Assigns the corresponding output pin to a programmable value defined by the output
compare mode (OCxM bits in the TIMx_CCMRx register) and the output polarity (CCxP
bit in the TIMx_CCER register). The output pin can keep its level (OCXM=000), be set
active (OCxM=001), be set inactive (OCxM=010) or can toggle (OCxM=011) on match.
•
Sets a flag in the interrupt status register (CCxIF bit in the TIMx_SR register).
•
Generates an interrupt if the corresponding interrupt mask is set (CCXIE bit in the
TIMx_DIER register).
•
Sends a DMA request if the corresponding enable bit is set (CCxDE bit in the
TIMx_DIER register, CCDS bit in the TIMx_CR2 register for the DMA request
selection).
The TIMx_CCRx registers can be programmed with or without preload registers using the
OCxPE bit in the TIMx_CCMRx register.
In output compare mode, the update event UEV has no effect on OCxREF and OCx output.
The timing resolution is one count of the counter. Output compare mode can also be used to
output a single pulse (in One Pulse mode).
Procedure:
1.
Select the counter clock (internal, external, prescaler).
2.
Write the desired data in the TIMx_ARR and TIMx_CCRx registers.
3.
Set the CCxIE bit if an interrupt request is to be generated.
4.
5.
Select the output mode. For example:
–
Write OCxM = 011 to toggle OCx output pin when CNT matches CCRx
–
Write OCxPE = 0 to disable preload register
–
Write CCxP = 0 to select active high polarity
–
Write CCxE = 1 to enable the output
Enable the counter by setting the CEN bit in the TIMx_CR1 register.
The TIMx_CCRx register can be updated at any time by software to control the output
waveform, provided that the preload register is not enabled (OCxPE=’0’, else TIMx_CCRx
shadow register is updated only at the next update event UEV). An example is given in
Figure 71.
234/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Figure 71. Output compare mode, toggle on OC1.
:ULWH%KLQWKH&&5UHJLVWHU
7,0B&17
$
7,0B&&5
%
$
%
%
%
2&5() 2&
0DWFKGHWHFWHGRQ&&5
,QWHUUXSWJHQHUDWHGLIHQDEOHG
069
12.3.10
PWM mode
Pulse Width Modulation mode allows generating a signal with a frequency determined by
the value of the TIMx_ARR register and a duty cycle determined by the value of the
TIMx_CCRx register.
The PWM mode can be selected independently on each channel (one PWM per OCx
output) by writing ‘110’ (PWM mode 1) or ‘111’ (PWM mode 2) in the OCxM bits in the
TIMx_CCMRx register. The corresponding preload register must be enabled by setting the
OCxPE bit in the TIMx_CCMRx register, and eventually the auto-reload preload register (in
upcounting or center-aligned modes) by setting the ARPE bit in the TIMx_CR1 register.
As the preload registers are transferred to the shadow registers only when an update event
occurs, before starting the counter, the user must initialize all the registers by setting the UG
bit in the TIMx_EGR register.
OCx polarity is software programmable using the CCxP bit in the TIMx_CCER register. It
can be programmed as active high or active low. OCx output is enabled by a combination of
the CCxE, CCxNE, MOE, OSSI and OSSR bits (TIMx_CCER and TIMx_BDTR registers).
Refer to the TIMx_CCER register description for more details.
In PWM mode (1 or 2), TIMx_CNT and TIMx_CCRx are always compared to determine
whether TIMx_CCRx ≤TIMx_CNT or TIMx_CNT ≤TIMx_CCRx (depending on the direction
of the counter).
The timer is able to generate PWM in edge-aligned mode or center-aligned mode
depending on the CMS bits in the TIMx_CR1 register.
PWM edge-aligned mode
•
Upcounting configuration
Upcounting is active when the DIR bit in the TIMx_CR1 register is low. Refer to
Upcounting mode.
In the following example, we consider PWM mode 1. The reference PWM signal
OCxREF is high as long as TIMx_CNT < TIMx_CCRx else it becomes low. If the
Doc ID16188 Rev 5
235/713
281
Advanced-control timer (TIM1)
RM0041
compare value in TIMx_CCRx is greater than the auto-reload value (in TIMx_ARR)
then OCxREF is held at ‘1’. If the compare value is 0 then OCxRef is held at ‘0’.
Figure 72 shows some edge-aligned PWM waveforms in an example where
TIMx_ARR=8.
Figure 72. Edge-aligned PWM waveforms (ARR=8)
&RXQWHUUHJLVWHU
&&5[ 2&;5()
&&[,)
2&;5()
&&5[ &&[,)
2&;5()
µ¶
&&5[!
&&[,)
2&;5()
µ¶
&&5[ &&[,)
069
•
Downcounting configuration
Downcounting is active when DIR bit in TIMx_CR1 register is high. Refer to
Downcounting mode
In PWM mode 1, the reference signal OCxRef is low as long as
TIMx_CNT > TIMx_CCRx else it becomes high. If the compare value in TIMx_CCRx is
greater than the auto-reload value in TIMx_ARR, then OCxREF is held at ‘1’. 0% PWM
is not possible in this mode.
PWM center-aligned mode
Center-aligned mode is active when the CMS bits in TIMx_CR1 register are different from
‘00’ (all the remaining configurations having the same effect on the OCxRef/OCx signals).
The compare flag is set when the counter counts up, when it counts down or both when it
counts up and down depending on the CMS bits configuration. The direction bit (DIR) in the
236/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
TIMx_CR1 register is updated by hardware and must not be changed by software. Refer to
Center-aligned mode (up/down counting).
Figure 73 shows some center-aligned PWM waveforms in an example where:
•
TIMx_ARR=8,
•
PWM mode is the PWM mode 1,
•
The flag is set when the counter counts down corresponding to the center-aligned
mode 1 selected for CMS=01 in TIMx_CR1 register.
Figure 73. Center-aligned PWM waveforms (ARR=8)
#OUNTERREGISTER
/#X2%&
##2X
#-3
#-3
#-3
##X)&
/#X2%&
##2X
#-3OR
##X)&
/#X2%&
##2X
gg
#-3
#-3
#-3
##X)&
/#X2%&
##2X
gg
#-3
#-3
#-3
##X)&
/#X2%&
##2X
##X)&
gg
#-3
#-3
#-3
AIB
Hints on using center-aligned mode:
•
When starting in center-aligned mode, the current up-down configuration is used. It
means that the counter counts up or down depending on the value written in the DIR bit
Doc ID16188 Rev 5
237/713
281
Advanced-control timer (TIM1)
RM0041
in the TIMx_CR1 register. Moreover, the DIR and CMS bits must not be changed at the
same time by the software.
•
•
12.3.11
Writing to the counter while running in center-aligned mode is not recommended as it
can lead to unexpected results. In particular:
–
The direction is not updated if the user writes a value in the counter greater than
the auto-reload value (TIMx_CNT>TIMx_ARR). For example, if the counter was
counting up, it will continue to count up.
–
The direction is updated if the user writes 0 or write the TIMx_ARR value in the
counter but no Update Event UEV is generated.
The safest way to use center-aligned mode is to generate an update by software
(setting the UG bit in the TIMx_EGR register) just before starting the counter and not to
write the counter while it is running.
Complementary outputs and dead-time insertion
The advanced-control timers (TIM1) can output two complementary signals and manage the
switching-off and the switching-on instants of the outputs.
This time is generally known as dead-time and it has to be adjust it depending on the
devices connected to the outputs and their characteristics (intrinsic delays of level-shifters,
delays due to power switches...)
User can select the polarity of the outputs (main output OCx or complementary OCxN)
independently for each output. This is done by writing to the CCxP and CCxNP bits in the
TIMx_CCER register.
The complementary signals OCx and OCxN are activated by a combination of several
control bits: the CCxE and CCxNE bits in the TIMx_CCER register and the MOE, OISx,
OISxN, OSSI and OSSR bits in the TIMx_BDTR and TIMx_CR2 registers. Refer to Table 68
for more details. In particular, the dead-time is activated when switching to the IDLE state
(MOE falling down to 0).
Dead-time insertion is enabled by setting both CCxE and CCxNE bits, and the MOE bit if the
break circuit is present. DTG[7:0] bits of the TIMx_BDTR register are used to control the
dead-time generation for all channels. From a reference waveform OCxREF, it generates 2
outputs OCx and OCxN. If OCx and OCxN are active high:
•
The OCx output signal is the same as the reference signal except for the rising edge,
which is delayed relative to the reference rising edge.
•
The OCxN output signal is the opposite of the reference signal except for the rising
edge, which is delayed relative to the reference falling edge.
If the delay is greater than the width of the active output (OCx or OCxN) then the
corresponding pulse is not generated.
The following figures show the relationships between the output signals of the dead-time
generator and the reference signal OCxREF. (we suppose CCxP=0, CCxNP=0, MOE=1,
CCxE=1 and CCxNE=1 in these examples)
238/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Figure 74. Complementary output with dead-time insertion.
2&[5()
2&[
GHOD\
2&[1
GHOD\
069
Figure 75. Dead-time waveforms with delay greater than the negative pulse.
2&[5()
2&[
GHOD\
2&[1
069
Figure 76. Dead-time waveforms with delay greater than the positive pulse.
2&[5()
2&[
2&[1
GHOD\
069
The dead-time delay is the same for each of the channels and is programmable with the
DTG bits in the TIMx_BDTR register. Refer to Section 12.4.18: TIM1 break and dead-time
register (TIMx_BDTR) for delay calculation.
Re-directing OCxREF to OCx or OCxN
In output mode (forced, output compare or PWM), OCxREF can be re-directed to the OCx
output or to OCxN output by configuring the CCxE and CCxNE bits in the TIMx_CCER
register.
This allows the user to send a specific waveform (such as PWM or static active level) on
one output while the complementary remains at its inactive level. Other possibilities are to
Doc ID16188 Rev 5
239/713
281
Advanced-control timer (TIM1)
RM0041
have both outputs at inactive level or both outputs active and complementary with deadtime.
Note:
When only OCxN is enabled (CCxE=0, CCxNE=1), it is not complemented and becomes
active as soon as OCxREF is high. For example, if CCxNP=0 then OCxN=OCxRef. On the
other hand, when both OCx and OCxN are enabled (CCxE=CCxNE=1) OCx becomes
active when OCxREF is high whereas OCxN is complemented and becomes active when
OCxREF is low.
12.3.12
Using the break function
When using the break function, the output enable signals and inactive levels are modified
according to additional control bits (MOE, OSSI and OSSR bits in the TIMx_BDTR register,
OISx and OISxN bits in the TIMx_CR2 register). In any case, the OCx and OCxN outputs
cannot be set both to active level at a given time. Refer to Table 68 for more details.
The break source can be either the break input pin or a clock failure event, generated by the
Clock Security System (CSS), from the Reset Clock Controller. For further information on
the Clock Security System, refer to Section 6.2.7: Clock security system (CSS).
When exiting from reset, the break circuit is disabled and the MOE bit is low. User can
enable the break function by setting the BKE bit in the TIMx_BDTR register. The break input
polarity can be selected by configuring the BKP bit in the same register. BKE and BKP can
be modified at the same time. When the BKE and BKP bits are written, a delay of 1 APB
clock cycle is applied before the writing is effective. Consequently, it is necessary to wait 1
APB clock period to correctly read back the bit after the write operation.
Because MOE falling edge can be asynchronous, a resynchronization circuit has been
inserted between the actual signal (acting on the outputs) and the synchronous control bit
(accessed in the TIMx_BDTR register). It results in some delays between the asynchronous
and the synchronous signals. In particular, if MOE is written to 1 whereas it was low, a delay
(dummy instruction) must be inserted before reading it correctly. This is because the user
writes an asynchronous signal, but reads a synchronous signal.
When a break occurs (selected level on the break input):
240/713
•
The MOE bit is cleared asynchronously, putting the outputs in inactive state, idle state
or in reset state (selected by the OSSI bit). This feature functions even if the MCU
oscillator is off.
•
Each output channel is driven with the level programmed in the OISx bit in the
TIMx_CR2 register as soon as MOE=0. If OSSI=0 then the timer releases the enable
output else the enable output remains high.
•
When complementary outputs are used:
–
The outputs are first put in reset state inactive state (depending on the polarity).
This is done asynchronously so that it works even if no clock is provided to the
timer.
–
If the timer clock is still present, then the dead-time generator is reactivated in
order to drive the outputs with the level programmed in the OISx and OISxN bits
after a dead-time. Even in this case, OCx and OCxN cannot be driven to their
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
active level together. Note that because of the resynchronization on MOE, the
dead-time duration is a bit longer than usual (around 2 ck_tim clock cycles).
–
Note:
If OSSI=0 then the timer releases the enable outputs else the enable outputs
remain or become high as soon as one of the CCxE or CCxNE bits is high.
•
The break status flag (BIF bit in the TIMx_SR register) is set. An interrupt can be
generated if the BIE bit in the TIMx_DIER register is set. A DMA request can be sent if
the BDE bit in the TIMx_DIER register is set.
•
If the AOE bit in the TIMx_BDTR register is set, the MOE bit is automatically set again
at the next update event UEV. This can be used to perform a regulation, for instance.
Else, MOE remains low until it is written to ‘1’ again. In this case, it can be used for
security and the break input can be connected to an alarm from power drivers, thermal
sensors or any security components.
The break inputs is acting on level. Thus, the MOE cannot be set while the break input is
active (neither automatically nor by software). In the meantime, the status flag BIF cannot
be cleared.
The break can be generated by the BRK input which has a programmable polarity and an
enable bit BKE in the TIMx_BDTR Register.
There are two solutions to generate a break:
•
By using the BRK input which has a programmable polarity and an enable bit BKE in
the TIMx_BDTR register
•
By software through the BG bit of the TIMx_EGR register.
In addition to the break input and the output management, a write protection has been
implemented inside the break circuit to safeguard the application. It allows freezing the
configuration of several parameters (dead-time duration, OCx/OCxN polarities and state
when disabled, OCxM configurations, break enable and polarity). The user can choose from
three levels of protection selected by the LOCK bits in the TIMx_BDTR register. Refer to
Section 12.4.18: TIM1 break and dead-time register (TIMx_BDTR). The LOCK bits can be
written only once after an MCU reset.
Figure 77 shows an example of behavior of the outputs in response to a break.
Doc ID16188 Rev 5
241/713
281
Advanced-control timer (TIM1)
RM0041
Figure 77. Output behavior in response to a break.
%5($.02(
2&[5()
2&[
2&[1QRWLPSOHPHQWHG&&[3 2,6[ 2&[
2&[1QRWLPSOHPHQWHG&&[3 2,6[ 2&[
2&[1QRWLPSOHPHQWHG&&[3 2,6[ 2&[
2&[1QRWLPSOHPHQWHG&&[3 2,6[ 2&[
GHOD\
GHOD\
2&[1
&&[( &&[3 2,6[ &&[1( &&[13 2,6[1 GHOD\
2&[
GHOD\
GHOD\
2&[1
&&[( &&[3 2,6[ &&[1( &&[13 2,6[1 GHOD\
2&[
2&[1
&&[( &&[3 2,6[ &&[1( &&[13 2,6[1 GHOD\
2&[
2&[1
&&[( &&[3 2,6[ &&[1( &&[13 2,6[1 GHOD\
2&[
2&[1
&&[( &&[3 &&[1( &&[13 2,6[ 2,6[1 RU2,6[ 2,6[1 069
242/713
Doc ID16188 Rev 5
RM0041
12.3.13
Advanced-control timer (TIM1)
Clearing the OCxREF signal on an external event
The OCxREF signal for a given channel can be driven Low by applying a High level to the
ETRF input (OCxCE enable bit of the corresponding TIMx_CCMRx register set to ‘1’). The
OCxREF signal remains Low until the next update event, UEV, occurs.
This function can only be used in output compare and PWM modes, and does not work in
forced mode.
For example, the ETR signal can be connected to the output of a comparator to be used for
current handling. In this case, the ETR must be configured as follow:
1.
The External Trigger Prescaler should be kept off: bits ETPS[1:0] of the TIMx_SMCR
register set to ‘00’.
2.
The external clock mode 2 must be disabled: bit ECE of the TIMx_SMCR register set to
‘0’.
3.
The External Trigger Polarity (ETP) and the External Trigger Filter (ETF) can be
configured according to the user needs.
Figure 78 shows the behavior of the OCxREF signal when the ETRF Input becomes High,
for both values of the enable bit OCxCE. In this example, the timer TIMx is programmed in
PWM mode.
Figure 78. Clearing TIMx OCxREF
&&5[
&RXQWHU&17
(75)
2&[5()2&[&( µ¶
2&[5()2&[&( µ¶
(75)EHFRPHVKLJK
(75)VWLOOKLJK
06Y9
Doc ID16188 Rev 5
243/713
281
Advanced-control timer (TIM1)
12.3.14
RM0041
6-step PWM generation
When complementary outputs are used on a channel, preload bits are available on the
OCxM, CCxE and CCxNE bits. The preload bits are transferred to the shadow bits at the
COM commutation event. The user can thus program in advance the configuration for the
next step and change the configuration of all the channels at the same time. COM can be
generated by software by setting the COM bit in the TIMx_EGR register or by hardware (on
TRGI rising edge).
A flag is set when the COM event occurs (COMIF bit in the TIMx_SR register), which can
generate an interrupt (if the COMIE bit is set in the TIMx_DIER register) or a DMA request
(if the COMDE bit is set in the TIMx_DIER register).
Figure 79 describes the behavior of the OCx and OCxN outputs when a COM event occurs,
in 3 different examples of programmed configurations.
Figure 79. 6-step generation, COM example (OSSR=1)
counter (CNT)
(CCRx)
OCxREF
Write COM to 1
COM event
Example 1
CCxE=1
write OCxM to 100
CCxNE=0
OCxM=100 (forced inactive)
CCxE=1
CCxNE=0
OCxM=100
Write CCxNE to 1
and OCxM to 101
CCxE=1
CCxNE=0
OCxM=100 (forced inactive)
CCxE=0
CCxNE=1
OCxM=101
OCx
OCxN
OCx
Example 2
OCxN
write CCxNE to 0
CCxE=1
and OCxM to 100
CCxNE=0
OCxM=100 (forced inactive)
Example 3
CCxE=1
CCxNE=0
OCxM=100
OCx
OCxN
ai14910
244/713
Doc ID16188 Rev 5
RM0041
One-pulse mode
One-pulse mode (OPM) is a particular case of the previous modes. It allows the counter to
be started in response to a stimulus and to generate a pulse with a programmable length
after a programmable delay.
Starting the counter can be controlled through the slave mode controller. Generating the
waveform can be done in output compare mode or PWM mode. Select One-pulse mode by
setting the OPM bit in the TIMx_CR1 register. This makes the counter stop automatically at
the next update event UEV.
A pulse can be correctly generated only if the compare value is different from the counter
initial value. Before starting (when the timer is waiting for the trigger), the configuration must
be:
•
In upcounting: CNT < CCRx ≤ ARR (in particular, 0 < CCRx)
•
In downcounting: CNT > CCRx
Figure 80. Example of one pulse mode.
7,
2&5()
2&
7,0B$55
&RXQWHU
12.3.15
Advanced-control timer (TIM1)
7,0B&&5
ƚ>z
ƚWh>^
ƚ
069
For example the user may want to generate a positive pulse on OC1 with a length of tPULSE
and after a delay of tDELAY as soon as a positive edge is detected on the TI2 input pin.
Let’s use TI2FP2 as trigger 1:
•
Map TI2FP2 to TI2 by writing CC2S=’01’ in the TIMx_CCMR1 register.
•
TI2FP2 must detect a rising edge, write CC2P=’0’ in the TIMx_CCER register.
•
Configure TI2FP2 as trigger for the slave mode controller (TRGI) by writing TS=’110’ in
the TIMx_SMCR register.
•
TI2FP2 is used to start the counter by writing SMS to ‘110’ in the TIMx_SMCR register
(trigger mode).
The OPM waveform is defined by writing the compare registers (taking into account the
clock frequency and the counter prescaler).
•
The tDELAY is defined by the value written in the TIMx_CCR1 register.
•
The tPULSE is defined by the difference between the auto-reload value and the compare
value (TIMx_ARR - TIMx_CCR1).
•
Let us say the user wants to build a waveform with a transition from ‘0’ to ‘1’ when a
compare match occurs and a transition from ‘1’ to ‘0’ when the counter reaches the
Doc ID16188 Rev 5
245/713
281
Advanced-control timer (TIM1)
RM0041
auto-reload value. To do this, enable PWM mode 2 by writing OC1M=111 in the
TIMx_CCMR1 register. The user can optionally enable the preload registers by writing
OC1PE=’1’ in the TIMx_CCMR1 register and ARPE in the TIMx_CR1 register. In this
case the compare value must be written in the TIMx_CCR1 register, the auto-reload
value in the TIMx_ARR register, generate an update by setting the UG bit and wait for
external trigger event on TI2. CC1P is written to ‘0’ in this example.
In our example, the DIR and CMS bits in the TIMx_CR1 register should be low.
The user only wants one pulse (Single mode), so '1’ must be written in the OPM bit in the
TIMx_CR1 register to stop the counter at the next update event (when the counter rolls over
from the auto-reload value back to 0). When OPM bit in the TIMx_CR1 register is set to '0',
so the Repetitive Mode is selected.
Particular case: OCx fast enable:
In One-pulse mode, the edge detection on TIx input set the CEN bit which enables the
counter. Then the comparison between the counter and the compare value makes the
output toggle. But several clock cycles are needed for these operations and it limits the
minimum delay tDELAY min we can get.
If the user wants to output a waveform with the minimum delay, the OCxFE bit in the
TIMx_CCMRx register must be set. Then OCxRef (and OCx) are forced in response to the
stimulus, without taking in account the comparison. Its new level is the same as if a compare
match had occurred. OCxFE acts only if the channel is configured in PWM1 or PWM2
mode.
12.3.16
Encoder interface mode
To select Encoder Interface mode write SMS=‘001’ in the TIMx_SMCR register if the
counter is counting on TI2 edges only, SMS=’010’ if it is counting on TI1 edges only and
SMS=’011’ if it is counting on both TI1 and TI2 edges.
Select the TI1 and TI2 polarity by programming the CC1P and CC2P bits in the TIMx_CCER
register. When needed, the user can program the input filter as well.
The two inputs TI1 and TI2 are used to interface to an incremental encoder. Refer to
Table 66. The counter is clocked by each valid transition on TI1FP1 or TI2FP2 (TI1 and TI2
after input filter and polarity selection, TI1FP1=TI1 if not filtered and not inverted,
TI2FP2=TI2 if not filtered and not inverted) assuming that it is enabled (CEN bit in
TIMx_CR1 register written to ‘1’). The sequence of transitions of the two inputs is evaluated
and generates count pulses as well as the direction signal. Depending on the sequence the
counter counts up or down, the DIR bit in the TIMx_CR1 register is modified by hardware
accordingly. The DIR bit is calculated at each transition on any input (TI1 or TI2), whatever
the counter is counting on TI1 only, TI2 only or both TI1 and TI2.
Encoder interface mode acts simply as an external clock with direction selection. This
means that the counter just counts continuously between 0 and the auto-reload value in the
TIMx_ARR register (0 to ARR or ARR down to 0 depending on the direction). So user must
configure TIMx_ARR before starting. in the same way, the capture, compare, prescaler,
repetition counter, trigger output features continue to work as normal. Encoder mode and
External clock mode 2 are not compatible and must not be selected together.
In this mode, the counter is modified automatically following the speed and the direction of
the incremental encoder and its content, therefore, always represents the encoder’s
position. The count direction correspond to the rotation direction of the connected sensor.
246/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
The table summarizes the possible combinations, assuming TI1 and TI2 don’t switch at the
same time.
Table 66. Counting direction versus encoder signals
Active edge
Level on
opposite
signal (TI1FP1
for TI2,
TI2FP2 for
TI1)
TI1FP1 signal
TI2FP2 signal
Rising
Falling
Rising
Falling
Counting on
TI1 only
High
Down
Up
No Count
No Count
Low
Up
Down
No Count
No Count
Counting on
TI2 only
High
No Count
No Count
Up
Down
Low
No Count
No Count
Down
Up
Counting on
TI1 and TI2
High
Down
Up
Up
Down
Low
Up
Down
Down
Up
An external incremental encoder can be connected directly to the MCU without external
interface logic. However, comparators are normally be used to convert the encoder’s
differential outputs to digital signals. This greatly increases noise immunity. The third
encoder output which indicate the mechanical zero position, may be connected to an
external interrupt input and trigger a counter reset.
Figure 81 gives an example of counter operation, showing count signal generation and
direction control. It also shows how input jitter is compensated where both edges are
selected. This might occur if the sensor is positioned near to one of the switching points. For
this example we assume that the configuration is the following:
•
CC1S=’01’ (TIMx_CCMR1 register, TI1FP1 mapped on TI1).
•
CC2S=’01’ (TIMx_CCMR2 register, TI1FP2 mapped on TI2).
•
CC1P=’0’, and IC1F = ‘0000’ (TIMx_CCER register, TI1FP1 non-inverted,
TI1FP1=TI1).
•
CC2P=’0’, and IC2F = ‘0000’ (TIMx_CCER register, TI1FP2 non-inverted, TI1FP2=
TI2).
•
SMS=’011’ (TIMx_SMCR register, both inputs are active on both rising and falling
edges).
•
CEN=’1’ (TIMx_CR1 register, Counter enabled).
Doc ID16188 Rev 5
247/713
281
Advanced-control timer (TIM1)
RM0041
Figure 81. Example of counter operation in encoder interface mode.
IRUZDUG
MLWWHU
EDFNZDUG
MLWWHU
IRUZDUG
7,
7,
&RXQWHU
XS
GRZQ
XS
069
Figure 82 gives an example of counter behavior when TI1FP1 polarity is inverted (same
configuration as above except CC1P=’1’).
Figure 82. Example of encoder interface mode with TI1FP1 polarity inverted.
IRUZDUG
MLWWHU
EDFNZDUG
MLWWHU
IRUZDUG
7,
7,
&RXQWHU
GRZQ
XS
GRZQ
069
The timer, when configured in Encoder Interface mode provides information on the sensor’s
current position.The user can obtain dynamic information (speed, acceleration,
deceleration) by measuring the period between two encoder events using a second timer
configured in capture mode. The output of the encoder which indicates the mechanical zero
can be used for this purpose. Depending on the time between two events, the counter can
also be read at regular times. This can be done by latching the counter value into a third
input capture register if available (then the capture signal must be periodic and can be
generated by another timer). when available, it is also possible to read its value through a
DMA request generated by a real-time clock.
248/713
Doc ID16188 Rev 5
RM0041
12.3.17
Advanced-control timer (TIM1)
Timer input XOR function
The TI1S bit in the TIMx_CR2 register, allows the input filter of channel 1 to be connected to
the output of a XOR gate, combining the three input pins TIMx_CH1, TIMx_CH2 and
TIMx_CH3.
The XOR output can be used with all the timer input functions such as trigger or input
capture. An example of this feature used to interface Hall sensors is given in
Section 12.3.18 below.
12.3.18
Interfacing with Hall sensors
This is done using the advanced-control timers (TIM1) to generate PWM signals to drive the
motor and another timer TIMx (TIM2, TIM3, TIM4 or TIM5) referred to as “interfacing timer”
in Figure 83. The “interfacing timer” captures the 3 timer input pins (TIMx_CH1, TIMx_CH2,
and TIMx_CH3) connected through a XOR to the TI1 input channel (selected by setting the
TI1S bit in the TIMx_CR2 register).
The slave mode controller is configured in reset mode; the slave input is TI1F_ED. Thus,
each time one of the 3 inputs toggles, the counter restarts counting from 0. This creates a
time base triggered by any change on the Hall inputs.
On the “interfacing timer”, capture/compare channel 1 is configured in capture mode,
capture signal is TRC (see Figure 66). The captured value, which corresponds to the time
elapsed between 2 changes on the inputs, gives information about motor speed.
The “interfacing timer” can be used in output mode to generate a pulse which changes the
configuration of the channels of the advanced-control timer (TIM1) (by triggering a COM
event). The TIM1 timer is used to generate PWM signals to drive the motor. To do this, the
interfacing timer channel must be programmed so that a positive pulse is generated after a
programmed delay (in output compare or PWM mode). This pulse is sent to the advancedcontrol timer (TIM1) through the TRGO output.
Example: the user wants to change the PWM configuration of the advanced-control timer
TIM1 after a programmed delay each time a change occurs on the Hall inputs connected to
one of the TIMx timers.
•
Configure 3 timer inputs ORed to the TI1 input channel by writing the TI1S bit in the
TIMx_CR2 register to ‘1’,
•
Program the time base: write the TIMx_ARR to the max value (the counter must be
cleared by the TI1 change. Set the prescaler to get a maximum counter period longer
than the time between 2 changes on the sensors,
•
Program channel 1 in capture mode (TRC selected): write the CC1S bits in the
TIMx_CCMR1 register to ‘11’. The user can also program the digital filter if needed,
•
Program channel 2 in PWM 2 mode with the desired delay: write the OC2M bits to ‘111’
and the CC2S bits to ‘00’ in the TIMx_CCMR1 register,
•
Select OC2REF as trigger output on TRGO: write the MMS bits in the TIMx_CR2
register to ‘101’,
In the advanced-control timer TIM1, the right ITR input must be selected as trigger input, the
timer is programmed to generate PWM signals, the capture/compare control signals are
preloaded (CCPC=1 in the TIMx_CR2 register) and the COM event is controlled by the
trigger input (CCUS=1 in the TIMx_CR2 register). The PWM control bits (CCxE, OCxM) are
written after a COM event for the next step (this can be done in an interrupt subroutine
generated by the rising edge of OC2REF).
Doc ID16188 Rev 5
249/713
281
Advanced-control timer (TIM1)
RM0041
Figure 83 describes this example.
Figure 83. Example of hall sensor interface
TIH1
TIH2
Interfacing timer
TIH3
counter (CNT)
(CCR2)
CCR1
C7A3
C7A8
C794
C7A5
C7AB
C796
TRGO=OC2REF
advanced-control timers (TIM1)
COM
OC1
OC1N
OC2
OC2N
OC3
OC3N
Write CCxE, CCxNE
and OCxM for next step
250/713
ai17336
Doc ID16188 Rev 5
RM0041
12.3.19
Advanced-control timer (TIM1)
TIMx and external trigger synchronization
The TIMx timer can be synchronized with an external trigger in several modes: Reset mode,
Gated mode and Trigger mode.
Slave mode: Reset mode
The counter and its prescaler can be reinitialized in response to an event on a trigger input.
Moreover, if the URS bit from the TIMx_CR1 register is low, an update event UEV is
generated. Then all the preloaded registers (TIMx_ARR, TIMx_CCRx) are updated.
In the following example, the upcounter is cleared in response to a rising edge on TI1 input:
•
Configure the channel 1 to detect rising edges on TI1. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC1F=0000). The capture
prescaler is not used for triggering, so there’s no need to configure it. The CC1S bits
select the input capture source only, CC1S = 01 in the TIMx_CCMR1 register. Write
CC1P=0 in TIMx_CCER register to validate the polarity (and detect rising edges only).
•
Configure the timer in reset mode by writing SMS=100 in TIMx_SMCR register. Select
TI1 as the input source by writing TS=101 in TIMx_SMCR register.
•
Start the counter by writing CEN=1 in the TIMx_CR1 register.
The counter starts counting on the internal clock, then behaves normally until TI1 rising
edge. When TI1 rises, the counter is cleared and restarts from 0. In the meantime, the
trigger flag is set (TIF bit in the TIMx_SR register) and an interrupt request, or a DMA
request can be sent if enabled (depending on the TIE and TDE bits in TIMx_DIER register).
The following figure shows this behavior when the auto-reload register TIMx_ARR=0x36.
The delay between the rising edge on TI1 and the actual reset of the counter is due to the
resynchronization circuit on TI1 input.
Figure 84. Control circuit in reset mode
7,
8*
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
069
Doc ID16188 Rev 5
251/713
281
Advanced-control timer (TIM1)
RM0041
Slave mode: Gated mode
The counter can be enabled depending on the level of a selected input.
In the following example, the upcounter counts only when TI1 input is low:
•
Configure the channel 1 to detect low levels on TI1. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC1F=0000). The capture
prescaler is not used for triggering, so the user does not need to configure it. The
CC1S bits select the input capture source only, CC1S=01 in TIMx_CCMR1 register.
Write CC1P=1 in TIMx_CCER register to validate the polarity (and detect low level
only).
•
Configure the timer in gated mode by writing SMS=101 in TIMx_SMCR register. Select
TI1 as the input source by writing TS=101 in TIMx_SMCR register.
•
Enable the counter by writing CEN=1 in the TIMx_CR1 register (in gated mode, the
counter doesn’t start if CEN=0, whatever is the trigger input level).
The counter starts counting on the internal clock as long as TI1 is low and stops as soon as
TI1 becomes high. The TIF flag in the TIMx_SR register is set both when the counter starts
or stops.
The delay between the rising edge on TI1 and the actual stop of the counter is due to the
resynchronization circuit on TI1 input.
Figure 85. Control circuit in gated mode
7,
&17B(1
&RXQWHUFORFN FNBFQW FNBSVF
&RXQWHUUHJLVWHU
7,)
:ULWH7,) 069
252/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Slave mode: Trigger mode
The counter can start in response to an event on a selected input.
In the following example, the upcounter starts in response to a rising edge on TI2 input:
•
Configure the channel 2 to detect rising edges on TI2. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC2F=0000). The capture
prescaler is not used for triggering, so there’s no need to configure it. The CC2S bits
are configured to select the input capture source only, CC2S=01 in TIMx_CCMR1
register. Write CC2P=1 in TIMx_CCER register to validate the polarity (and detect low
level only).
•
Configure the timer in trigger mode by writing SMS=110 in TIMx_SMCR register. Select
TI2 as the input source by writing TS=110 in TIMx_SMCR register.
When a rising edge occurs on TI2, the counter starts counting on the internal clock and the
TIF flag is set.
The delay between the rising edge on TI2 and the actual start of the counter is due to the
resynchronization circuit on TI2 input.
Figure 86. Control circuit in trigger mode
7,
&17B(1
&RXQWHUFORFN FNBFQW FNBSVF
&RXQWHUUHJLVWHU
7,)
069
Slave mode: external clock mode 2 + trigger mode
The external clock mode 2 can be used in addition to another slave mode (except external
clock mode 1 and encoder mode). In this case, the ETR signal is used as external clock
input, and another input can be selected as trigger input (in reset mode, gated mode or
trigger mode). It is recommended not to select ETR as TRGI through the TS bits of
TIMx_SMCR register.
In the following example, the upcounter is incremented at each rising edge of the ETR
signal as soon as a rising edge of TI1 occurs:
1.
2.
Configure the external trigger input circuit by programming the TIMx_SMCR register as
follows:
–
ETF = 0000: no filter
–
ETPS = 00: prescaler disabled
–
ETP = 0: detection of rising edges on ETR and ECE=1 to enable the external clock
mode 2.
Configure the channel 1 as follows, to detect rising edges on TI:
–
IC1F=0000: no filter.
–
The capture prescaler is not used for triggering and does not need to be
configured.
–
CC1S=01 in TIMx_CCMR1 register to select only the input capture source
Doc ID16188 Rev 5
253/713
281
Advanced-control timer (TIM1)
–
3.
RM0041
CC1P=0 in TIMx_CCER register to validate the polarity (and detect rising edge
only).
Configure the timer in trigger mode by writing SMS=110 in TIMx_SMCR register. Select
TI1 as the input source by writing TS=101 in TIMx_SMCR register.
A rising edge on TI1 enables the counter and sets the TIF flag. The counter then counts on
ETR rising edges.
The delay between the rising edge of the ETR signal and the actual reset of the counter is
due to the resynchronization circuit on ETRP input.
Figure 87. Control circuit in external clock mode 2 + trigger mode
7,
&(1&17B(1
(75
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
069
12.3.20
Timer synchronization
The TIM timers are linked together internally for timer synchronization or chaining. Refer to
Section 13.3.15: Timer synchronization for details.
Note:
The clock of the slave timer must be enabled prior to receive events from the master timer,
and must not be changed on-the-fly while triggers are received from the master timer.
12.3.21
Debug mode
When the microcontroller enters debug mode (Cortex®-M3 core halted), the TIMx counter
either continues to work normally or stops, depending on DBG_TIMx_STOP configuration
bit in DBG module. For more details, refer to Section 25.15.2: Debug support for timers,
watchdog and I2C.
254/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
12.4
TIM1 registers
Refer to Section: List of abbreviations for registers for a list of abbreviations used in register
descriptions.
The peripheral registers can be accessed by half-words (16-bit) or words (32-bit).
12.4.1
TIM1 control register 1 (TIMx_CR1)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
Reserved
11
10
9
8
CKD[1:0]
rw
7
ARPE
rw
rw
6
5
CMS[1:0]
rw
rw
4
3
2
1
0
DIR
OPM
URS
UDIS
CEN
rw
rw
rw
rw
rw
Bits 15:10 Reserved, must be kept at reset value.
Bits 9:8 CKD[1:0]: Clock division
This bit-field indicates the division ratio between the timer clock (CK_INT) frequency and the
dead-time and sampling clock (tDTS)used by the dead-time generators and the digital filters
(ETR, TIx),
00: tDTS=tCK_INT
01: tDTS=2*tCK_INT
10: tDTS=4*tCK_INT
11: Reserved, do not program this value
Bit 7 ARPE: Auto-reload preload enable
0: TIMx_ARR register is not buffered
1: TIMx_ARR register is buffered
Bits 6:5 CMS[1:0]: Center-aligned mode selection
00: Edge-aligned mode. The counter counts up or down depending on the direction bit
(DIR).
01: Center-aligned mode 1. The counter counts up and down alternatively. Output compare
interrupt flags of channels configured in output (CCxS=00 in TIMx_CCMRx register) are set
only when the counter is counting down.
10: Center-aligned mode 2. The counter counts up and down alternatively. Output compare
interrupt flags of channels configured in output (CCxS=00 in TIMx_CCMRx register) are set
only when the counter is counting up.
11: Center-aligned mode 3. The counter counts up and down alternatively. Output compare
interrupt flags of channels configured in output (CCxS=00 in TIMx_CCMRx register) are set
both when the counter is counting up or down.
Note: It is not allowed to switch from edge-aligned mode to center-aligned mode as long as
the counter is enabled (CEN=1)
Bit 4 DIR: Direction
0: Counter used as upcounter
1: Counter used as downcounter
Note: This bit is read only when the timer is configured in Center-aligned mode or Encoder
mode.
Bit 3 OPM: One pulse mode
0: Counter is not stopped at update event
1: Counter stops counting at the next update event (clearing the bit CEN)
Doc ID16188 Rev 5
255/713
281
Advanced-control timer (TIM1)
RM0041
Bit 2 URS: Update request source
This bit is set and cleared by software to select the UEV event sources.
0: Any of the following events generate an update interrupt or DMA request if enabled.
These events can be:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
1: Only counter overflow/underflow generates an update interrupt or DMA request if
enabled.
Bit 1 UDIS: Update disable
This bit is set and cleared by software to enable/disable UEV event generation.
0: UEV enabled. The Update (UEV) event is generated by one of the following events:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
Buffered registers are then loaded with their preload values.
1: UEV disabled. The Update event is not generated, shadow registers keep their value
(ARR, PSC, CCRx). However the counter and the prescaler are reinitialized if the UG bit is
set or if a hardware reset is received from the slave mode controller.
Bit 0 CEN: Counter enable
0: Counter disabled
1: Counter enabled
Note: External clock, gated mode and encoder mode can work only if the CEN bit has been
previously set by software. However trigger mode can set the CEN bit automatically by
hardware.
12.4.2
TIM1 control register 2 (TIMx_CR2)
Address offset: 0x04
Reset value: 0x0000
15
Res.
14
13
12
11
10
9
8
7
OIS4
OIS3N
OIS3
OIS2N
OIS2
OIS1N
OIS1
TI1S
rw
rw
rw
rw
rw
rw
rw
rw
Bit 15 Reserved, must be kept at reset value.
Bit 14 OIS4: Output Idle state 4 (OC4 output)
refer to OIS1 bit
Bit 13 OIS3N: Output Idle state 3 (OC3N output)
refer to OIS1N bit
Bit 12 OIS3: Output Idle state 3 (OC3 output)
refer to OIS1 bit
Bit 11 OIS2N: Output Idle state 2 (OC2N output)
refer to OIS1N bit
Bit 10 OIS2: Output Idle state 2 (OC2 output)
refer to OIS1 bit
256/713
Doc ID16188 Rev 5
6
5
4
MMS[2:0]
rw
rw
rw
3
2
CCDS
CCUS
rw
rw
1
Res.
0
CCPC
rw
RM0041
Advanced-control timer (TIM1)
Bit 9 OIS1N: Output Idle state 1 (OC1N output)
0: OC1N=0 after a dead-time when MOE=0
1: OC1N=1 after a dead-time when MOE=0
Note: This bit can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BDTR register).
Bit 8 OIS1: Output Idle state 1 (OC1 output)
0: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0
Note: This bit can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BDTR register).
Bit 7 TI1S: TI1 selection
0: The TIMx_CH1 pin is connected to TI1 input
1: The TIMx_CH1, CH2 and CH3 pins are connected to the TI1 input (XOR combination)
Bits 6:4 MMS[2:0]: Master mode selection
These bits allow to select the information to be sent in master mode to slave timers for
synchronization (TRGO). The combination is as follows:
000: Reset - the UG bit from the TIMx_EGR register is used as trigger output (TRGO). If the
reset is generated by the trigger input (slave mode controller configured in reset mode) then
the signal on TRGO is delayed compared to the actual reset.
001: Enable - the Counter Enable signal CNT_EN is used as trigger output (TRGO). It is
useful to start several timers at the same time or to control a window in which a slave timer is
enable. The Counter Enable signal is generated by a logic OR between CEN control bit and
the trigger input when configured in gated mode. When the Counter Enable signal is
controlled by the trigger input, there is a delay on TRGO, except if the master/slave mode is
selected (see the MSM bit description in TIMx_SMCR register).
010: Update - The update event is selected as trigger output (TRGO). For instance a master
timer can then be used as a prescaler for a slave timer.
011: Compare Pulse - The trigger output send a positive pulse when the CC1IF flag is to be
set (even if it was already high), as soon as a capture or a compare match occurred.
(TRGO).
100: Compare - OC1REF signal is used as trigger output (TRGO)
101: Compare - OC2REF signal is used as trigger output (TRGO)
110: Compare - OC3REF signal is used as trigger output (TRGO)
111: Compare - OC4REF signal is used as trigger output (TRGO)
Note: The clock of the slave timer and ADC must be enabled prior to receiving events from
the master timer, and must not be changed on-the-fly while triggers are received from
the master timer.
Bit 3 CCDS: Capture/compare DMA selection
0: CCx DMA request sent when CCx event occurs
1: CCx DMA requests sent when update event occurs
Doc ID16188 Rev 5
257/713
281
Advanced-control timer (TIM1)
RM0041
Bit 2 CCUS: Capture/compare control update selection
0: When capture/compare control bits are preloaded (CCPC=1), they are updated by setting
the COMG bit only
1: When capture/compare control bits are preloaded (CCPC=1), they are updated by setting
the COMG bit or when an rising edge occurs on TRGI
Note: This bit acts only on channels that have a complementary output.
Bit 1 Reserved, must be kept at reset value.
Bit 0 CCPC: Capture/compare preloaded control
0: CCxE, CCxNE and OCxM bits are not preloaded
1: CCxE, CCxNE and OCxM bits are preloaded, after having been written, they are updated
only when a commutation event (COM) occurs (COMG bit set or rising edge detected on
TRGI, depending on the CCUS bit).
Note: This bit acts only on channels that have a complementary output.
258/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
12.4.3
TIM1 slave mode control register (TIMx_SMCR)
Address offset: 0x08
Reset value: 0x0000
15
14
ETP
ECE
rw
rw
13
12
11
ETPS[1:0]
rw
rw
10
9
8
ETF[3:0]
rw
rw
rw
7
6
MSM
rw
rw
5
4
TS[2:0]
rw
rw
3
2
Res.
rw
Res.
1
0
SMS[2:0]
rw
rw
rw
Bit 15 ETP: External trigger polarity
This bit selects whether ETR or ETR is used for trigger operations
0: ETR is non-inverted, active at high level or rising edge.
1: ETR is inverted, active at low level or falling edge.
Bit 14 ECE: External clock enable
This bit enables External clock mode 2.
0: External clock mode 2 disabled
1: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF
signal.
Note: 1: Setting the ECE bit has the same effect as selecting external clock mode 1 with
TRGI connected to ETRF (SMS=111 and TS=111).
2: It is possible to simultaneously use external clock mode 2 with the following slave
modes: reset mode, gated mode and trigger mode. Nevertheless, TRGI must not be
connected to ETRF in this case (TS bits must not be 111).
3: If external clock mode 1 and external clock mode 2 are enabled at the same time,
the external clock input is ETRF.
Bits 13:12 ETPS[1:0]: External trigger prescaler
External trigger signal ETRP frequency must be at most 1/4 of TIMxCLK frequency. A
prescaler can be enabled to reduce ETRP frequency. It is useful when inputting fast external
clocks.
00: Prescaler OFF
01: ETRP frequency divided by 2
10: ETRP frequency divided by 4
11: ETRP frequency divided by 8
Doc ID16188 Rev 5
259/713
281
Advanced-control timer (TIM1)
RM0041
Bits 11:8 ETF[3:0]: External trigger filter
This bit-field then defines the frequency used to sample ETRP signal and the length of the
digital filter applied to ETRP. The digital filter is made of an event counter in which N
consecutive events are needed to validate a transition on the output:
0000: No filter, sampling is done at fDTS
0001: fSAMPLING=fCK_INT, N=2
0010: fSAMPLING=fCK_INT, N=4
0011: fSAMPLING=fCK_INT, N=8
0100: fSAMPLING=fDTS/2, N=6
0101: fSAMPLING=fDTS/2, N=8
0110: fSAMPLING=fDTS/4, N=6
0111: fSAMPLING=fDTS/4, N=8
1000: fSAMPLING=fDTS/8, N=6
1001: fSAMPLING=fDTS/8, N=8
1010: fSAMPLING=fDTS/16, N=5
1011: fSAMPLING=fDTS/16, N=6
1100: fSAMPLING=fDTS/16, N=8
1101: fSAMPLING=fDTS/32, N=5
1110: fSAMPLING=fDTS/32, N=6
1111: fSAMPLING=fDTS/32, N=8
Bit 7 MSM: Master/slave mode
0: No action
1: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect
synchronization between the current timer and its slaves (through TRGO). It is useful if we
want to synchronize several timers on a single external event.
Bits 6:4 TS[2:0]: Trigger selection
This bit-field selects the trigger input to be used to synchronize the counter.
000: Internal Trigger 0 (ITR0)
001: Internal Trigger 1 (ITR1)
010: Internal Trigger 2 (ITR2)
011: Internal Trigger 3 (ITR3)
100: TI1 Edge Detector (TI1F_ED)
101: Filtered Timer Input 1 (TI1FP1)
110: Filtered Timer Input 2 (TI2FP2)
111: External Trigger input (ETRF)
See Table 67 for more details on ITRx meaning for each Timer.
Note: These bits must be changed only when they are not used (e.g. when SMS=000) to
avoid wrong edge detections at the transition.
Bit 3 Reserved, must be kept at reset value.
260/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Bits 2:0 SMS: Slave mode selection
When external signals are selected the active edge of the trigger signal (TRGI) is linked to
the polarity selected on the external input (see Input Control register and Control Register
description.
000: Slave mode disabled - if CEN = ‘1’ then the prescaler is clocked directly by the internal
clock.
001: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2
level.
010: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1
level.
011: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges
depending on the level of the other input.
100: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter
and generates an update of the registers.
101: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The
counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of
the counter are controlled.
110: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not
reset). Only the start of the counter is controlled.
111: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.
Note: The gated mode must not be used if TI1F_ED is selected as the trigger input
(TS=’100’). Indeed, TI1F_ED outputs 1 pulse for each transition on TI1F, whereas the
gated mode checks the level of the trigger signal.
The clock of the slave timer must be enabled prior to receiving events from the master
timer, and must not be changed on-the-fly while triggers are received from the master
timer.
Table 67. TIMx Internal trigger connection
Slave TIM
ITR0 (TS = 000)
ITR1 (TS = 001)
ITR2 (TS = 010)
ITR3 (TS = 011)
TIM1
TIM5_TRGO or
TIM15_TRGO(1)
TIM2_TRGO
TIM3_TRGO
TIM4_TRGO
1. TIM5 only in high density value line devices. Selection of TIM5 or TIM15 depends on the MISC_REMAP bit
in the AFIO_MAPR2 register.
12.4.4
TIM1 DMA/interrupt enable register (TIMx_DIER)
Address offset: 0x0C
Reset value: 0x0000
15
Res.
14
TDE
rw
13
12
11
10
9
COMDE CC4DE CC3DE CC2DE CC1DE
rw
rw
rw
rw
rw
8
7
6
5
4
3
2
1
0
UDE
BIE
TIE
COMIE
CC4IE
CC3IE
CC2IE
CC1IE
UIE
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bit 15 Reserved, must be kept at reset value.
Bit 14 TDE: Trigger DMA request enable
0: Trigger DMA request disabled
1: Trigger DMA request enabled
Bit 13 COMDE: COM DMA request enable
0: COM DMA request disabled
1: COM DMA request enabled
Doc ID16188 Rev 5
261/713
281
Advanced-control timer (TIM1)
RM0041
Bit 12 CC4DE: Capture/Compare 4 DMA request enable
0: CC4 DMA request disabled
1: CC4 DMA request enabled
Bit 11 CC3DE: Capture/Compare 3 DMA request enable
0: CC3 DMA request disabled
1: CC3 DMA request enabled
Bit 10 CC2DE: Capture/Compare 2 DMA request enable
0: CC2 DMA request disabled
1: CC2 DMA request enabled
Bit 9 CC1DE: Capture/Compare 1 DMA request enable
0: CC1 DMA request disabled
1: CC1 DMA request enabled
Bit 8 UDE: Update DMA request enable
0: Update DMA request disabled
1: Update DMA request enabled
Bit 7 BIE: Break interrupt enable
0: Break interrupt disabled
1: Break interrupt enabled
Bit 6 TIE: Trigger interrupt enable
0: Trigger interrupt disabled
1: Trigger interrupt enabled
Bit 5 COMIE: COM interrupt enable
0: COM interrupt disabled
1: COM interrupt enabled
Bit 4 CC4IE: Capture/Compare 4 interrupt enable
0: CC4 interrupt disabled
1: CC4 interrupt enabled
Bit 3 CC3IE: Capture/Compare 3 interrupt enable
0: CC3 interrupt disabled
1: CC3 interrupt enabled
Bit 2 CC2IE: Capture/Compare 2 interrupt enable
0: CC2 interrupt disabled
1: CC2 interrupt enabled
Bit 1 CC1IE: Capture/Compare 1 interrupt enable
0: CC1 interrupt disabled
1: CC1 interrupt enabled
Bit 0 UIE: Update interrupt enable
0: Update interrupt disabled
1: Update interrupt enabled
262/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
12.4.5
TIM1 status register (TIMx_SR)
Address offset: 0x10
Reset value: 0x0000
15
14
Reserved
13
12
11
10
9
CC4OF CC3OF CC2OF CC1OF
rc_w0
rc_w0
rc_w0
rc_w0
8
7
6
5
4
3
2
1
0
Res.
BIF
TIF
COMIF
CC4IF
CC3IF
CC2IF
CC1IF
UIF
Res.
rc_w0
rc_w0
rc_w0
rc_w0
rc_w0
rc_w0
rc_w0
rc_w0
Bits 15:13 Reserved, must be kept at reset value.
Bit 12 CC4OF: Capture/Compare 4 overcapture flag
refer to CC1OF description
Bit 11 CC3OF: Capture/Compare 3 overcapture flag
refer to CC1OF description
Bit 10 CC2OF: Capture/Compare 2 overcapture flag
refer to CC1OF description
Bit 9 CC1OF: Capture/Compare 1 overcapture flag
This flag is set by hardware only when the corresponding channel is configured in input
capture mode. It is cleared by software by writing it to ‘0’.
0: No overcapture has been detected.
1: The counter value has been captured in TIMx_CCR1 register while CC1IF flag was
already set
Bit 8 Reserved, must be kept at reset value.
Bit 7 BIF: Break interrupt flag
This flag is set by hardware as soon as the break input goes active. It can be cleared by
software if the break input is not active.
0: No break event occurred.
1: An active level has been detected on the break input.
Bit 6 TIF: Trigger interrupt flag
This flag is set by hardware on trigger event (active edge detected on TRGI input when the
slave mode controller is enabled in all modes but gated mode.It is cleared by software.
0: No trigger event occurred.
1: Trigger interrupt pending.
Bit 5 COMIF: COM interrupt flag
This flag is set by hardware on COM event (when Capture/compare Control bits - CCxE,
CCxNE, OCxM - have been updated). It is cleared by software.
0: No COM event occurred.
1: COM interrupt pending.
Bit 4 CC4IF: Capture/Compare 4 interrupt flag
refer to CC1IF description
Bit 3 CC3IF: Capture/Compare 3 interrupt flag
refer to CC1IF description
Doc ID16188 Rev 5
263/713
281
Advanced-control timer (TIM1)
RM0041
Bit 2 CC2IF: Capture/Compare 2 interrupt flag
refer to CC1IF description
Bit 1 CC1IF: Capture/Compare 1 interrupt flag
If channel CC1 is configured as output:
This flag is set by hardware when the counter matches the compare value, with some
exception in center-aligned mode (refer to the CMS bits in the TIMx_CR1 register
description). It is cleared by software.
0: No match.
1: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register.
When the contents of TIMx_CCR1 are greater than the contents of TIMx_ARR, the CC1IF
bit goes high on the counter overflow (in upcounting and up/down-counting modes) or
underflow (in downcounting mode)
If channel CC1 is configured as input:
This bit is set by hardware on a capture. It is cleared by software or by reading the
TIMx_CCR1 register.
0: No input capture occurred
1: The counter value has been captured in TIMx_CCR1 register (An edge has been
detected on IC1 which matches the selected polarity)
Bit 0 UIF: Update interrupt flag
This bit is set by hardware on an update event. It is cleared by software.
0: No update occurred.
1: Update interrupt pending. This bit is set by hardware when the registers are updated:
– At overflow or underflow regarding the repetition counter value (update if repetition counter
= 0) and if the UDIS=0 in the TIMx_CR1 register.
– When CNT is reinitialized by software using the UG bit in TIMx_EGR register, if URS=0 and
UDIS=0 in the TIMx_CR1 register.
– When CNT is reinitialized by a trigger event (refer to Section 12.4.3: TIM1 slave mode
control register (TIMx_SMCR)), if URS=0 and UDIS=0 in the TIMx_CR1 register.
12.4.6
TIM1 event generation register (TIMx_EGR)
Address offset: 0x14
Reset value: 0x0000
15
14
13
12
11
Reserved
10
9
8
7
6
5
4
3
2
1
0
BG
TG
COMG
CC4G
CC3G
CC2G
CC1G
UG
w
w
w
w
w
w
w
w
Bits 15:8 Reserved, must be kept at reset value.
Bit 7 BG: Break generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: A break event is generated. MOE bit is cleared and BIF flag is set. Related interrupt or
DMA transfer can occur if enabled.
Bit 6 TG: Trigger generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if
enabled.
264/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Bit 5 COMG: Capture/Compare control update generation
This bit can be set by software, it is automatically cleared by hardware
0: No action
1: When CCPC bit is set, it allows to update CCxE, CCxNE and OCxM bits
Note: This bit acts only on channels having a complementary output.
Bit 4 CC4G: Capture/Compare 4 generation
refer to CC1G description
Bit 3 CC3G: Capture/Compare 3 generation
refer to CC1G description
Bit 2 CC2G: Capture/Compare 2 generation
refer to CC1G description
Bit 1 CC1G: Capture/Compare 1 generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: A capture/compare event is generated on channel 1:
If channel CC1 is configured as output:
CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled.
If channel CC1 is configured as input:
The current value of the counter is captured in TIMx_CCR1 register. The CC1IF flag is set,
the corresponding interrupt or DMA request is sent if enabled. The CC1OF flag is set if the
CC1IF flag was already high.
Bit 0 UG: Update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action
1: Reinitialize the counter and generates an update of the registers. Note that the prescaler
counter is cleared too (anyway the prescaler ratio is not affected). The counter is cleared if
the center-aligned mode is selected or if DIR=0 (upcounting), else it takes the auto-reload
value (TIMx_ARR) if DIR=1 (downcounting).
Doc ID16188 Rev 5
265/713
281
Advanced-control timer (TIM1)
12.4.7
RM0041
TIM1 capture/compare mode register 1 (TIMx_CCMR1)
Address offset: 0x18
Reset value: 0x0000
The channels can be used in input (capture mode) or in output (compare mode). The
direction of a channel is defined by configuring the corresponding CCxS bits. All the other
bits of this register have a different function in input and in output mode. For a given bit,
OCxx describes its function when the channel is configured in output, ICxx describes its
function when the channel is configured in input. So the user must take care that the same
bit can have a different meaning for the input stage and for the output stage.
15
14
OC2
CE
13
12
OC2M[2:0]
IC2F[3:0]
rw
rw
rw
11
10
OC2
PE
OC2
FE
9
8
CC2S[1:0]
7
IC2PSC[1:0]
rw
rw
rw
6
OC1
CE
5
4
OC1M[2:0]
IC1F[3:0]
rw
rw
rw
rw
rw
3
2
OC1
PE
OC1
FE
1
0
CC1S[1:0]
IC1PSC[1:0]
rw
rw
rw
rw
rw
Output compare mode:
Bit 15 OC2CE: Output Compare 2 clear enable
Bits 14:12 OC2M[2:0]: Output Compare 2 mode
Bit 11 OC2PE: Output Compare 2 preload enable
Bit 10 OC2FE: Output Compare 2 fast enable
Bits 9:8 CC2S[1:0]: Capture/Compare 2 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output
01: CC2 channel is configured as input, IC2 is mapped on TI2
10: CC2 channel is configured as input, IC2 is mapped on TI1
11: CC2 channel is configured as input, IC2 is mapped on TRC. This mode is working only if
an internal trigger input is selected through the TS bit (TIMx_SMCR register)
Note: CC2S bits are writable only when the channel is OFF (CC2E = ‘0’ in TIMx_CCER).
Bit 7 OC1CE: Output Compare 1 clear enable
OC1CE: Output Compare 1 Clear Enable
0: OC1Ref is not affected by the ETRF Input
1: OC1Ref is cleared as soon as a High level is detected on ETRF input
266/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Bits 6:4 OC1M: Output Compare 1 mode
These bits define the behavior of the output reference signal OC1REF from which OC1 and
OC1N are derived. OC1REF is active high whereas OC1 and OC1N active level depends
on CC1P and CC1NP bits.
000: Frozen - The comparison between the output compare register TIMx_CCR1 and the
counter TIMx_CNT has no effect on the outputs.(this mode is used to generate a timing
base).
001: Set channel 1 to active level on match. OC1REF signal is forced high when the counter
TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
010: Set channel 1 to inactive level on match. OC1REF signal is forced low when the
counter TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
011: Toggle - OC1REF toggles when TIMx_CNT=TIMx_CCR1.
100: Force inactive level - OC1REF is forced low.
101: Force active level - OC1REF is forced high.
110: PWM mode 1 - In upcounting, channel 1 is active as long as TIMx_CNT<TIMx_CCR1
else inactive. In downcounting, channel 1 is inactive (OC1REF=‘0’) as long as
TIMx_CNT>TIMx_CCR1 else active (OC1REF=’1’).
111: PWM mode 2 - In upcounting, channel 1 is inactive as long as TIMx_CNT<TIMx_CCR1
else active. In downcounting, channel 1 is active as long as TIMx_CNT>TIMx_CCR1 else
inactive.
Note: 1: These bits can not be modified as long as LOCK level 3 has been programmed
(LOCK bits in TIMx_BDTR register) and CC1S=’00’ (the channel is configured in
output).
2: In PWM mode 1 or 2, the OCREF level changes only when the result of the
comparison changes or when the output compare mode switches from “frozen” mode
to “PWM” mode.
Bit 3 OC1PE: Output Compare 1 preload enable
0: Preload register on TIMx_CCR1 disabled. TIMx_CCR1 can be written at anytime, the
new value is taken in account immediately.
1: Preload register on TIMx_CCR1 enabled. Read/Write operations access the preload
register. TIMx_CCR1 preload value is loaded in the active register at each update event.
Note: 1: These bits can not be modified as long as LOCK level 3 has been programmed
(LOCK bits in TIMx_BDTR register) and CC1S=’00’ (the channel is configured in
output).
2: The PWM mode can be used without validating the preload register only in one
pulse mode (OPM bit set in TIMx_CR1 register). Else the behavior is not guaranteed.
Bit 2 OC1FE: Output Compare 1 fast enable
This bit is used to accelerate the effect of an event on the trigger in input on the CC output.
0: CC1 behaves normally depending on counter and CCR1 values even when the trigger is
ON. The minimum delay to activate CC1 output when an edge occurs on the trigger input is
5 clock cycles.
1: An active edge on the trigger input acts like a compare match on CC1 output. Then, OC is
set to the compare level independently from the result of the comparison. Delay to sample
the trigger input and to activate CC1 output is reduced to 3 clock cycles. OCFE acts only if
the channel is configured in PWM1 or PWM2 mode.
Bits 1:0 CC1S: Capture/Compare 1 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10: CC1 channel is configured as input, IC1 is mapped on TI2
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = ‘0’ in TIMx_CCER).
Doc ID16188 Rev 5
267/713
281
Advanced-control timer (TIM1)
RM0041
Input capture mode
Bits 15:12 IC2F: Input capture 2 filter
Bits 11:10 IC2PSC[1:0]: Input capture 2 prescaler
Bits 9:8 CC2S: Capture/Compare 2 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output
01: CC2 channel is configured as input, IC2 is mapped on TI2
10: CC2 channel is configured as input, IC2 is mapped on TI1
11: CC2 channel is configured as input, IC2 is mapped on TRC. This mode is working only if an
internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC2S bits are writable only when the channel is OFF (CC2E = ‘0’ in TIMx_CCER).
Bits 7:4 IC1F[3:0]: Input capture 1 filter
This bit-field defines the frequency used to sample TI1 input and the length of the digital filter applied
to TI1. The digital filter is made of an event counter in which N consecutive events are needed to
validate a transition on the output:
0000: No filter, sampling is done at fDTS
0001: fSAMPLING=fCK_INT, N=2
0010: fSAMPLING=fCK_INT, N=4
0011: fSAMPLING=fCK_INT, N=8
0100: fSAMPLING=fDTS/2, N=6
0101: fSAMPLING=fDTS/2, N=8
0110: fSAMPLING=fDTS/4, N=6
0111: fSAMPLING=fDTS/4, N=8
1000: fSAMPLING=fDTS/8, N=6
1001: fSAMPLING=fDTS/8, N=8
1010: fSAMPLING=fDTS/16, N=5
1011: fSAMPLING=fDTS/16, N=6
1100: fSAMPLING=fDTS/16, N=8
1101: fSAMPLING=fDTS/32, N=5
1110: fSAMPLING=fDTS/32, N=6
1111: fSAMPLING=fDTS/32, N=8
Bits 3:2 IC1PSC: Input capture 1 prescaler
This bit-field defines the ratio of the prescaler acting on CC1 input (IC1).
The prescaler is reset as soon as CC1E=’0’ (TIMx_CCER register).
00: no prescaler, capture is done each time an edge is detected on the capture input
01: capture is done once every 2 events
10: capture is done once every 4 events
11: capture is done once every 8 events
Bits 1:0 CC1S: Capture/Compare 1 Selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10: CC1 channel is configured as input, IC1 is mapped on TI2
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only if an
internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = ‘0’ in TIMx_CCER).
12.4.8
TIM1 capture/compare mode register 2 (TIMx_CCMR2)
Address offset: 0x1C
268/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Reset value: 0x0000
Refer to the above CCMR1 register description.
15
14
OC4
CE
13
12
OC4M[2:0]
IC4F[3:0]
rw
rw
rw
11
10
OC4
PE
OC4
FE
9
8
CC4S[1:0]
7
OC3
CE.
IC4PSC[1:0]
rw
rw
rw
6
5
4
OC3M[2:0]
IC3F[3:0]
rw
rw
rw
rw
rw
3
2
OC3
PE
OC3
FE
1
0
CC3S[1:0]
IC3PSC[1:0]
rw
rw
rw
rw
rw
Output compare mode
Bit 15 OC4CE: Output compare 4 clear enable
Bits 14:12 OC4M: Output compare 4 mode
Bit 11 OC4PE: Output compare 4 preload enable
Bit 10 OC4FE: Output compare 4 fast enable
Bits 9:8 CC4S: Capture/Compare 4 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC4 channel is configured as output
01: CC4 channel is configured as input, IC4 is mapped on TI4
10: CC4 channel is configured as input, IC4 is mapped on TI3
11: CC4 channel is configured as input, IC4 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC4S bits are writable only when the channel is OFF (CC4E = ‘0’ in TIMx_CCER).
Bit 7 OC3CE: Output compare 3 clear enable
Bits 6:4 OC3M: Output compare 3 mode
Bit 3 OC3PE: Output compare 3 preload enable
Bit 2 OC3FE: Output compare 3 fast enable
Bits 1:0 CC3S: Capture/Compare 3 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC3 channel is configured as output
01: CC3 channel is configured as input, IC3 is mapped on TI3
10: CC3 channel is configured as input, IC3 is mapped on TI4
11: CC3 channel is configured as input, IC3 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC3S bits are writable only when the channel is OFF (CC3E = ‘0’ in TIMx_CCER).
Doc ID16188 Rev 5
269/713
281
Advanced-control timer (TIM1)
RM0041
Input capture mode
Bits 15:12 IC4F: Input capture 4 filter
Bits 11:10 IC4PSC: Input capture 4 prescaler
Bits 9:8 CC4S: Capture/Compare 4 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC4 channel is configured as output
01: CC4 channel is configured as input, IC4 is mapped on TI4
10: CC4 channel is configured as input, IC4 is mapped on TI3
11: CC4 channel is configured as input, IC4 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC4S bits are writable only when the channel is OFF (CC4E = ‘0’ in TIMx_CCER).
Bits 7:4 IC3F: Input capture 3 filter
Bits 3:2 IC3PSC: Input capture 3 prescaler
Bits 1:0 CC3S: Capture/compare 3 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC3 channel is configured as output
01: CC3 channel is configured as input, IC3 is mapped on TI3
10: CC3 channel is configured as input, IC3 is mapped on TI4
11: CC3 channel is configured as input, IC3 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC3S bits are writable only when the channel is OFF (CC3E = ‘0’ in TIMx_CCER).
12.4.9
TIM1 capture/compare enable register (TIMx_CCER)
Address offset: 0x20
Reset value: 0x0000
15
14
Reserved
13
12
CC4P
CC4E
rw
rw
11
10
CC3NP CC3NE
rw
rw
9
8
CC3P
CC3E
rw
rw
7
6
CC2NP CC2NE
rw
rw
5
4
CC2P
CC2E
rw
rw
Bits 15:14 Reserved, must be kept at reset value.
Bit 13 CC4P: Capture/Compare 4 output polarity
refer to CC1P description
Bit 12 CC4E: Capture/Compare 4 output enable
refer to CC1E description
Bit 11 CC3NP: Capture/Compare 3 complementary output polarity
refer to CC1NP description
Bit 10 CC3NE: Capture/Compare 3 complementary output enable
refer to CC1NE description
Bit 9 CC3P: Capture/Compare 3 output polarity
refer to CC1P description
Bit 8 CC3E: Capture/Compare 3 output enable
refer to CC1E description
270/713
Doc ID16188 Rev 5
3
2
CC1NP CC1NE
rw
rw
1
0
CC1P
CC1E
rw
rw
RM0041
Advanced-control timer (TIM1)
Bit 7 CC2NP: Capture/Compare 2 complementary output polarity
refer to CC1NP description
Bit 6 CC2NE: Capture/Compare 2 complementary output enable
refer to CC1NE description
Bit 5 CC2P: Capture/Compare 2 output polarity
refer to CC1P description
Bit 4 CC2E: Capture/Compare 2 output enable
refer to CC1E description
Bit 3 CC1NP: Capture/Compare 1 complementary output polarity
0: OC1N active high.
1: OC1N active low.
Note: This bit is not writable as soon as LOCK level 2 or 3 has been programmed (LOCK bits
in TIMx_BDTR register) and CC1S=”00” (the channel is configured in output).
Bit 2 CC1NE: Capture/Compare 1 complementary output enable
0: Off - OC1N is not active. OC1N level is then function of MOE, OSSI, OSSR, OIS1, OIS1N
and CC1E bits.
1: On - OC1N signal is output on the corresponding output pin depending on MOE, OSSI,
OSSR, OIS1, OIS1N and CC1E bits.
Bit 1 CC1P: Capture/Compare 1 output polarity
CC1 channel configured as output:
0: OC1 active high
1: OC1 active low
CC1 channel configured as input:
This bit selects whether IC1 or IC1 is used for trigger or capture operations.
0: non-inverted: capture is done on a rising edge of IC1. When used as external trigger, IC1
is non-inverted.
1: inverted: capture is done on a falling edge of IC1. When used as external trigger, IC1 is
inverted.
Note: This bit is not writable as soon as LOCK level 2 or 3 has been programmed (LOCK bits
in TIMx_BDTR register).
Bit 0 CC1E: Capture/Compare 1 output enable
CC1 channel configured as output:
0: Off - OC1 is not active. OC1 level is then function of MOE, OSSI, OSSR, OIS1, OIS1N
and CC1NE bits.
1: On - OC1 signal is output on the corresponding output pin depending on MOE, OSSI,
OSSR, OIS1, OIS1N and CC1NE bits.
CC1 channel configured as input:
This bit determines if a capture of the counter value can actually be done into the input
capture/compare register 1 (TIMx_CCR1) or not.
0: Capture disabled.
1: Capture enabled.
Doc ID16188 Rev 5
271/713
281
Advanced-control timer (TIM1)
RM0041
Table 68. Output control bits for complementary OCx and OCxN channels with
break feature
Output states(1)
Control bits
MOE
bit
OSSI
bit
1
OSSR
bit
CCxE
bit
CCxNE
bit
0
0
0
Output Disabled (not driven by Output Disabled (not driven by the
the timer), OCx=0, OCx_EN=0 timer), OCxN=0, OCxN_EN=0
0
0
1
Output Disabled (not driven by OCxREF + Polarity OCxN=OCxREF
the timer), OCx=0, OCx_EN=0 xor CCxNP, OCxN_EN=1
0
1
0
OCxREF + Polarity
OCx=OCxREF xor CCxP,
OCx_EN=1
0
1
1
Complementary to OCREF (not
OCREF + Polarity + dead-time
OCREF) + Polarity + dead-time
OCx_EN=1
OCxN_EN=1
1
0
0
Output Disabled (not driven by
the timer)
OCx=CCxP, OCx_EN=0
Output Disabled (not driven by the
timer)
OCxN=CCxNP, OCxN_EN=0
1
0
1
Off-State (output enabled with
inactive state)
OCx=CCxP, OCx_EN=1
OCxREF + Polarity
OCxN=OCxREF xor CCxNP,
OCxN_EN=1
1
1
0
OCxREF + Polarity
OCx=OCxREF xor CCxP,
OCx_EN=1
Off-State (output enabled with
inactive state)
OCxN=CCxNP, OCxN_EN=1
1
1
1
Complementary to OCREF (not
OCREF + Polarity + dead-time
OCREF) + Polarity + dead-time
OCx_EN=1
OCxN_EN=1
X
OCx output state
OCxN output state
Output Disabled (not driven by the
timer)
OCxN=0, OCxN_EN=0
1. When both outputs of a channel are not used (CCxE = CCxNE = 0), the OISx, OISxN, CCxP and CCxNP bits must be kept
cleared.
Note:
The state of the external I/O pins connected to the complementary OCx and OCxN channels
depends on the OCx and OCxN channel state and the GPIOand AFIO registers.
12.4.10
TIM1 counter (TIMx_CNT)
Address offset: 0x24
Reset value: 0x0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CNT[15:0]
rw
Bits 15:0 CNT[15:0]: Counter value
12.4.11
TIM1 prescaler (TIMx_PSC)
Address offset: 0x28
272/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
PSC[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 PSC[15:0]: Prescaler value
The counter clock frequency (CK_CNT) is equal to fCK_PSC / (PSC[15:0] + 1).
PSC contains the value to be loaded in the active prescaler register at each update event
(including when the counter is cleared through UG bit of TIMx_EGR register or through
trigger controller when configured in “reset mode”).
12.4.12
TIM1 auto-reload register (TIMx_ARR)
Address offset: 0x2C
Reset value: 0x0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
ARR[15:0]
rw
Bits 15:0 ARR[15:0]: Auto-reload value
ARR is the value to be loaded in the actual auto-reload register.
Refer to Section 12.3.1: Time-base unit for more details about ARR update and behavior.
The counter is blocked while the auto-reload value is null.
Doc ID16188 Rev 5
273/713
281
Advanced-control timer (TIM1)
12.4.13
RM0041
TIM1 repetition counter register (TIMx_RCR)
Address offset: 0x30
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
REP[7:0]
Reserved
rw
rw
rw
rw
rw
Bits 15:8 Reserved, must be kept at reset value.
Bits 7:0 REP[7:0]: Repetition counter value
These bits allow the user to set-up the update rate of the compare registers (i.e. periodic
transfers from preload to active registers) when preload registers are enable, as well as the
update interrupt generation rate, if this interrupt is enable.
Each time the REP_CNT related downcounter reaches zero, an update event is generated
and it restarts counting from REP value. As REP_CNT is reloaded with REP value only at
the repetition update event U_RC, any write to the TIMx_RCR register is not taken in
account until the next repetition update event.
It means in PWM mode (REP+1) corresponds to:
–
the number of PWM periods in edge-aligned mode
–
the number of half PWM period in center-aligned mode.
12.4.14
TIM1 capture/compare register 1 (TIMx_CCR1)
Address offset: 0x34
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR1[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR1[15:0]: Capture/Compare 1 value
If channel CC1 is configured as output:
CCR1 is the value to be loaded in the actual capture/compare 1 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR1 register
(bit OC1PE). Else the preload value is copied in the active capture/compare 1 register when
an update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signaled on OC1 output.
If channel CC1 is configured as input:
CCR1 is the counter value transferred by the last input capture 1 event (IC1).
274/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
12.4.15
TIM1 capture/compare register 2 (TIMx_CCR2)
Address offset: 0x38
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR2[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR2[15:0]: Capture/Compare 2 value
If channel CC2 is configured as output:
CCR2 is the value to be loaded in the actual capture/compare 2 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR2 register
(bit OC2PE). Else the preload value is copied in the active capture/compare 2 register when
an update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signalled on OC2 output.
If channel CC2 is configured as input:
CCR2 is the counter value transferred by the last input capture 2 event (IC2).
12.4.16
TIM1 capture/compare register 3 (TIMx_CCR3)
Address offset: 0x3C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR3[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR3[15:0]: Capture/Compare value
If channel CC3 is configured as output:
CCR3 is the value to be loaded in the actual capture/compare 3 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR3 register
(bit OC3PE). Else the preload value is copied in the active capture/compare 3 register when
an update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signalled on OC3 output.
If channel CC3 is configured as input:
CCR3 is the counter value transferred by the last input capture 3 event (IC3).
Doc ID16188 Rev 5
275/713
281
Advanced-control timer (TIM1)
12.4.17
RM0041
TIM1 capture/compare register 4 (TIMx_CCR4)
Address offset: 0x40
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR4[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR4[15:0]: Capture/Compare value
If channel CC4 is configured as output:
CCR4 is the value to be loaded in the actual capture/compare 4 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR4 register
(bit OC4PE). Else the preload value is copied in the active capture/compare 4 register when
an update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signalled on OC4 output.
If channel CC4 is configured as input:
CCR4 is the counter value transferred by the last input capture 4 event (IC4).
12.4.18
TIM1 break and dead-time register (TIMx_BDTR)
Address offset: 0x44
Reset value: 0x0000
15
14
13
12
11
10
MOE
AOE
BKP
BKE
OSSR
OSSI
rw
rw
rw
rw
rw
rw
Note:
9
8
7
6
5
LOCK[1:0]
rw
rw
4
3
2
1
0
rw
rw
rw
DTG[7:0]
rw
rw
rw
rw
rw
As the bits AOE, BKP, BKE, OSSI, OSSR and DTG[7:0] can be write-locked depending on
the LOCK configuration, it can be necessary to configure all of them during the first write
access to the TIMx_BDTR register.
Bit 15 MOE: Main output enable
This bit is cleared asynchronously by hardware as soon as the break input is active. It is set
by software or automatically depending on the AOE bit. It is acting only on the channels
which are configured in output.
0: OC and OCN outputs are disabled or forced to idle state.
1: OC and OCN outputs are enabled if their respective enable bits are set (CCxE, CCxNE in
TIMx_CCER register).
See OC/OCN enable description for more details (Section 12.4.9: TIM1 capture/compare
enable register (TIMx_CCER)).
Bit 14 AOE: Automatic output enable
0: MOE can be set only by software
1: MOE can be set by software or automatically at the next update event (if the break input is
not be active)
Note: This bit can not be modified as long as LOCK level 1 has been programmed (LOCK bits
in TIMx_BDTR register).
276/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
Bit 13 BKP: Break polarity
0: Break input BRK is active low
1: Break input BRK is active high
Note: This bit can not be modified as long as LOCK level 1 has been programmed (LOCK bits
in TIMx_BDTR register).
Note: Any write operation to this bit takes a delay of 1 APB clock cycle to become effective.
Bit 12 BKE: Break enable
0: Break inputs (BRK and CSS clock failure event) disabled
1; Break inputs (BRK and CSS clock failure event) enabled
Note: This bit cannot be modified when LOCK level 1 has been programmed (LOCK bits in
TIMx_BDTR register).
Note: Any write operation to this bit takes a delay of 1 APB clock cycle to become effective.
Bit 11 OSSR: Off-state selection for Run mode
This bit is used when MOE=1 on channels having a complementary output which are
configured as outputs. OSSR is not implemented if no complementary output is implemented
in the timer.
See OC/OCN enable description for more details (Section 12.4.9: TIM1 capture/compare
enable register (TIMx_CCER)).
0: When inactive, OC/OCN outputs are disabled (OC/OCN enable output signal=0).
1: When inactive, OC/OCN outputs are enabled with their inactive level as soon as CCxE=1
or CCxNE=1. Then, OC/OCN enable output signal=1
Note: This bit can not be modified as soon as the LOCK level 2 has been programmed (LOCK
bits in TIMx_BDTR register).
Bit 10 OSSI: Off-state selection for Idle mode
This bit is used when MOE=0 on channels configured as outputs.
See OC/OCN enable description for more details (Section 12.4.9: TIM1 capture/compare
enable register (TIMx_CCER)).
0: When inactive, OC/OCN outputs are disabled (OC/OCN enable output signal=0).
1: When inactive, OC/OCN outputs are forced first with their idle level as soon as CCxE=1 or
CCxNE=1. OC/OCN enable output signal=1)
Note: This bit can not be modified as soon as the LOCK level 2 has been programmed (LOCK
bits in TIMx_BDTR register).
Bits 9:8 LOCK[1:0]: Lock configuration
These bits offer a write protection against software errors.
00: LOCK OFF - No bit is write protected.
01: LOCK Level 1 = DTG bits in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2
register and BKE/BKP/AOE bits in TIMx_BDTR register can no longer be written.
10: LOCK Level 2 = LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER
register, as long as the related channel is configured in output through the CCxS bits) as well
as OSSR and OSSI bits can no longer be written.
11: LOCK Level 3 = LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in
TIMx_CCMRx registers, as long as the related channel is configured in output through the
CCxS bits) can no longer be written.
Note: The LOCK bits can be written only once after the reset. Once the TIMx_BDTR register
has been written, their content is frozen until the next reset.
Doc ID16188 Rev 5
277/713
281
Advanced-control timer (TIM1)
RM0041
Bits 7:0 DTG[7:0]: Dead-time generator setup
This bit-field defines the duration of the dead-time inserted between the complementary
outputs. DT correspond to this duration.
DTG[7:5]=0xx => DT=DTG[7:0]x tdtg with tdtg=tDTS.
DTG[7:5]=10x => DT=(64+DTG[5:0])xtdtg with Tdtg=2xtDTS.
DTG[7:5]=110 => DT=(32+DTG[4:0])xtdtg with Tdtg=8xtDTS.
DTG[7:5]=111 => DT=(32+DTG[4:0])xtdtg with Tdtg=16xtDTS.
Example if TDTS=125ns (8MHz), dead-time possible values are:
0 to 15875 ns by 125 ns steps,
16 us to 31750 ns by 250 ns steps,
32 us to 63us by 1 us steps,
64 us to 126 us by 2 us steps
Note: This bit-field can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BDTR register).
12.4.19
TIM1 DMA control register (TIMx_DCR)
Address offset: 0x48
Reset value: 0x0000
15
14
13
Reserved
12
11
10
9
8
DBL[4:0]
rw
rw
rw
rw
rw
7
6
Reserved
5
4
3
2
1
0
rw
rw
DBA[4:0]
rw
rw
rw
Bits 15:13 Reserved, must be kept at reset value.
Bits 12:8 DBL[4:0]: DMA burst length
This 5-bit vector defines the number of DMA transfers (the timer detects a burst transfer
when a read or a write access to the TIMx_DMAR register address is performed).
the TIMx_DMAR address)
00000: 1 transfer
00001: 2 transfers
00010: 3 transfers
...
10001: 18 transfers
Bits 7:5 Reserved, must be kept at reset value.
Bits 4:0 DBA[4:0]: DMA base address
This 5-bits vector defines the base-address for DMA transfers (when read/write access are
done through the TIMx_DMAR address). DBA is defined as an offset starting from the
address of the TIMx_CR1 register.
Example:
00000: TIMx_CR1,
00001: TIMx_CR2,
00010: TIMx_SMCR,
...
Example: Let us consider the following transfer: DBL = 7 transfers and DBA = TIMx_CR1. In
this case the transfer is done to/from 7 registers starting from the TIMx_CR1 address.
278/713
Doc ID16188 Rev 5
RM0041
Advanced-control timer (TIM1)
12.4.20
TIM1 DMA address for full transfer (TIMx_DMAR)
Address offset: 0x4C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
DMAB[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 DMAB[15:0]: DMA register for burst accesses
A read or write operation to the DMAR register accesses the register located at the address
(TIMx_CR1 address) + (DBA + DMA index) x 4
where TIMx_CR1 address is the address of the control register 1, DBA is the DMA base
address configured in TIMx_DCR register, DMA index is automatically controlled by the
DMA transfer, and ranges from 0 to DBL (DBL configured in TIMx_DCR).
Example of how to use the DMA burst feature
In this example the timer DMA burst feature is used to update the contents of the CCRx
registers (x = 2, 3, 4) with the DMA transferring half words into the CCRx registers.
This is done in the following steps:
1.
Note:
Configure the corresponding DMA channel as follows:
–
DMA channel peripheral address is the DMAR register address
–
DMA channel memory address is the address of the buffer in the RAM containing
the data to be transferred by DMA into CCRx registers.
–
Number of data to transfer = 3 (See note below).
–
Circular mode disabled.
2.
Configure the DCR register by configuring the DBA and DBL bit fields as follows:
DBL = 3 transfers, DBA = 0xE.
3.
Enable the TIMx update DMA request (set the UDE bit in the DIER register).
4.
Enable TIMx
5.
Enable the DMA channel
This example is for the case where every CCRx register to be updated once. If every CCRx
register is to be updated twice for example, the number of data to transfer should be 6. Let's
take the example of a buffer in the RAM containing data1, data2, data3, data4, data5 and
data6. The data is transferred to the CCRx registers as follows: on the first update DMA
request, data1 is transferred to CCR2, data2 is transferred to CCR3, data3 is transferred to
CCR4 and on the second update DMA request, data4 is transferred to CCR2, data5 is
transferred to CCR3 and data6 is transferred to CCR4.
Doc ID16188 Rev 5
279/713
281
Advanced-control timer (TIM1)
12.4.21
RM0041
TIM1 register map
TIM1 registers are mapped as 16-bit addressable registers as described in the table below:
Reserved
0
0
3
2
1
0
URS
UDIS
CEN
CCUS
Reserved
CCPC
CC2IF
CC1IF
UIF
CC2G
CC1G
UG
0
0
0
0
0
0
CC4S
[1:0]
0
0
CC4S
[1:0]
0
0
0
IC1F[3:0]
0
IC4
PSC
[1:0]
OC1M
[2:0]
0
0
0
OC3M
[2:0]
0
0
0
0
IC3F[3:0]
OC1FE
0
OC1PE
0
0
0
0
CC1
S
[1:0]
0
0
IC1
PSC
[1:0]
CC1
S
[1:0]
0
0
0
0
0
0
CC3
S
[1:0]
0
0
IC3
PSC
[1:0]
CC3
S
[1:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CC1E
0
CC1P
0
CC1NE
0
CC1NP
0
CC2E
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CNT[15:0]
Reserved
0
0
0
0
0
0
0
0
0
PSC[15:0]
Reserved
0
Doc ID16188 Rev 5
0
OC1CE
OC2FE
0
0
CC3E
Reserved
0
0
CC3P
0
0
0
OC3FE
0
CC2S
[1:0]
0
OC3PE
0
0
0
CC2P
0
0
0
OC3CE
OC4M
[2:0]
IC4F[3:0]
0
Reset value
280/713
0
0
IC2
PSC
[1:0]
0
CC2NE
TIMx_PSC
0
0
OC4FE
0
OC2PE
OC2CE
IC2F[3:0]
Reserved
Reset value
0x28
0
0
CC2NP
TIMx_CNT
0
OC4PE
0
CC2S
[1:0]
CC3IF
0
CC3G
0
CC4IF
0
CC4G
0
COMIF
0
COMG
0
TIF
0
TG
0
BIF
0
BG
UIE
0
CC1IE
0
CC2IE
CC1OF
0
OC2M
[2:0]
Reset value
0x24
4
Reserved
CC2OF
0
CC3IE
0
CC4IE
0
COMIE
0
0
TIE
CC1DE
0
0
BIE
CC2DE
0
0
CC3NE
TIMx_CCER
5
0
SMS[2:0]
CC3NP
0x20
OPM
TI1S
0
MSM
0
0
Reset value
CCDS
OIS1
0
0
Reset value
TIMx_CCMR2
Input Capture
mode
DIR
OIS1N
0
TS[2:0]
0
CC4E
0x1C
6
OIS2
0
Reserved
Reserved
0
CC4P
TIMx_CCMR2
Output
Compare mode
0
0
0
0
Reset value
0
0
0
Reserved
Reset value
TIMx_CCMR1
Input Capture
mode
MMS[2:0]
0
O24CE
0x18
0
0
Reserved
Reserved
0
0
ETF[3:0]
Reset value
TIMx_CCMR1
Output
Compare mode
0
0
Reserved
TIMx_EGR
7
OIS2N
0
Reset value
0x14
8
OIS3
0
CC3DE
TIMx_SR
0
0
0
0
Reset value
0x10
0
CC3OF
TIMx_DIER
0
CC4DE
0x0C
0
ETP
S
[1:0]
CC4OF
Reset value
0
COMDE
Reserved
0
0
0
ECE
TIMx_SMCR
0
TDE
0x08
0
ETP
Reset value
0
OIS3N
Reserved
CMS
[1:0]
OIS4
TIMx_CR2
ARPE
CKD
[1:0]
Reserved
Reset value
0x04
9
11
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
TIMx_CR1
UDE
0x00
Register
30
Offset
31
Table 69. TIM1 register map and reset values
0
0
0
0
0
0
0
0
RM0041
Advanced-control timer (TIM1)
0
0
0
0
TIMx_DCR
0
0
TIMx_DMAR
0
0
0
0
0
6
0
0
0
0
0
0
0
0
0
0
0
0
0
0
OSSI
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
LOCK
[1:0]
0
0
DBL[4:0]
Reserved
0
DT[7:0]
0
0
0
0
DBA[4:0]
Reserved
0
0
0
0
0
0
0
0
0
0
0
0
DMAB[15:0]
Reserved
Reset value
0
CCR4[15:0]
Reserved
Reserved
0
CCR3[15:0]
Reserved
Reset value
0x4C
0
CCR2[15:0]
0
Reset value
0x48
0
OSSR
TIMx_BDTR
0
Reserved
Reset value
0x44
0
BKE
TIMx_CCR4
0
CCR1[15:0]
Reserved
Reset value
0x40
0
REP[7:0]
BKP
TIMx_CCR3
0
0
Reset value
0x3C
0
0
AOE
TIMx_CCR2
1
0
Reserved
Reset value
0x38
2
0
MOE
TIMx_CCR1
3
0
Reset value
0x34
7
8
9
11
10
12
13
14
15
16
17
18
19
20
21
22
23
24
26
27
28
29
25
0
TIMx_RCR
0
ARR[15:0]
Reserved
Reset value
0x30
4
TIMx_ARR
5
0x2C
Register
30
Offset
31
Table 69. TIM1 register map and reset values (continued)
0
0
0
0
0
0
0
0
0
0
0
Refer to Section: Memory map for the register boundary addresses.
Doc ID16188 Rev 5
281/713
281
General-purpose timers (TIM2 to TIM5)
13
RM0041
General-purpose timers (TIM2 to TIM5)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
13.1
TIM2 to TIM5 introduction
The general-purpose timers consist of a 16-bit auto-reload counter driven by a
programmable prescaler.
They may be used for a variety of purposes, including measuring the pulse lengths of input
signals (input capture) or generating output waveforms (output compare and PWM).
Pulse lengths and waveform periods can be modulated from a few microseconds to several
milliseconds using the timer prescaler and the RCC clock controller prescalers.
The timers are completely independent, and do not share any resources. They can be
synchronized together as described in Section 13.3.15.
282/713
Doc ID16188 Rev 5
RM0041
13.2
General-purpose timers (TIM2 to TIM5)
TIM2 to TIM5 main features
General-purpose TIMx timer features include:
•
16-bit up, down, up/down auto-reload counter.
•
16-bit programmable prescaler used to divide (also “on the fly”) the counter clock
frequency by any factor between 1 and 65536.
•
Up to 4 independent channels for:
–
Input capture
–
Output compare
–
PWM generation (Edge- and Center-aligned modes)
–
One-pulse mode output
•
Synchronization circuit to control the timer with external signals and to interconnect
several timers.
•
Interrupt/DMA generation on the following events:
–
Update: counter overflow/underflow, counter initialization (by software or
internal/external trigger)
–
Trigger event (counter start, stop, initialization or count by internal/external trigger)
–
Input capture
–
Output compare
•
Supports incremental (quadrature) encoder and hall-sensor circuitry for positioning
purposes
•
Trigger input for external clock or cycle-by-cycle current management
Doc ID16188 Rev 5
283/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Figure 88. General-purpose timer block diagram
Internal clock (CK_INT)
TIMxCLK from RCC
ETRF
ETRP
ETR
TIMx_ETR
Polarity selection & edge
detector & prescaler
Input filter
TRGO
ITR0
ITR1
TGI
ITR
ITR2
TRC
TRGI
ITR3
TI1F_ED
TI1FP1
Trigger
controller
Slave
Reset, enable, up/down, count
mode
controller
Encoder
Interface
TI2FP2
U
Autoreload register
Stop, clear or up/down
CK_PSC
PSC
CK_CNT
Prescaler
TI1
Input filter &
edge detector
TI1FP1
TI1FP2
IC1
Prescaler
IC1PS U
counter
CC1I
TI2
TIMx_CH2
Input filter &
edge detector
TI2FP1
TI2FP2
Capture/compare 1 register
CC2I
IC2
OC1REF
output
OC1
control
TRC
TIMx_CH1
UI
U
CNT
+/-
CC1I
XOR
to other timers
to DAC/ADC
CC2I
IC2PS U
Prescaler
TIMx_CH1
Capture/compare 2 register
OC2REF
output
OC2
control
TIMx_CH2
TRC
CC3I
TI3
TIMx_CH3
Input filter &
edge detector
TI3FP3
TI3FP4
IC3
Prescaler
IC3PS
TRC
TI4
TIMx_CH4
Input filter &
edge detector
TI4FP3
TI4FP4
CC3I
U
Capture/compare 3 register
CC4I
IC4
IC4PS
OC3REF
OC3
TIMx_CH3
CC4I
U
Prescaler
output
control
Capture/compare 4 register
OC4REF
output
control
OC4
TIMx_CH4
TRC
ETRF
OCREF_CLR
ETRF
Notes:
Reg
Preload registers transferred
to active registers on U event
according to control bit
event
interrupt & DMA output
ai17188
13.3
TIM2 to TIM5 functional description
13.3.1
Time-base unit
The main block of the programmable timer is a 16-bit counter with its related auto-reload
register. The counter can count up but also down or both up and down. The counter clock
can be divided by a prescaler.
The counter, the auto-reload register and the prescaler register can be written or read by
software. This is true even when the counter is running.
The time-base unit includes:
284/713
•
Counter Register (TIMx_CNT)
•
Prescaler Register (TIMx_PSC):
•
Auto-Reload Register (TIMx_ARR)
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
The auto-reload register is preloaded. Writing to or reading from the auto-reload register
accesses the preload register. The content of the preload register are transferred into the
shadow register permanently or at each update event (UEV), depending on the auto-reload
preload enable bit (ARPE) in TIMx_CR1 register. The update event is sent when the counter
reaches the overflow (or underflow when downcounting) and if the UDIS bit equals 0 in the
TIMx_CR1 register. It can also be generated by software. The generation of the update
event is described in detail for each configuration.
The counter is clocked by the prescaler output CK_CNT, which is enabled only when the
counter enable bit (CEN) in TIMx_CR1 register is set (refer also to the slave mode controller
description to get more details on counter enabling).
Note that the actual counter enable signal CNT_EN is set 1 clock cycle after CEN.
Prescaler description
The prescaler can divide the counter clock frequency by any factor between 1 and 65536. It
is based on a 16-bit counter controlled through a 16-bit register (in the TIMx_PSC register).
It can be changed on the fly as this control register is buffered. The new prescaler ratio is
taken into account at the next update event.
Figure 89 and Figure 90 give some examples of the counter behavior when the prescaler
ratio is changed on the fly:
Figure 89. Counter timing diagram with prescaler division change from 1 to 2
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
) ) )$ )% )&
8SGDWHHYHQW8(9
3UHVFDOHUFRQWUROUHJLVWHU
:ULWHDQHZYDOXHLQ7,0[B36&
3UHVFDOHUEXIIHU
3UHVFDOHUFRXQWHU
069
Doc ID16188 Rev 5
285/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Figure 90. Counter timing diagram with prescaler division change from 1 to 4
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
) ) )$ )% )&
8SGDWHHYHQW8(9
3UHVFDOHUFRQWUROUHJLVWHU
:ULWHDQHZYDOXHLQ7,0[B36&
3UHVFDOHUEXIIHU
3UHVFDOHUFRXQWHU
069
13.3.2
Counter modes
Upcounting mode
In upcounting mode, the counter counts from 0 to the auto-reload value (content of the
TIMx_ARR register), then restarts from 0 and generates a counter overflow event.
An Update event can be generated at each counter overflow or by setting the UG bit in the
TIMx_EGR register (by software or by using the slave mode controller).
The UEV event can be disabled by software by setting the UDIS bit in TIMx_CR1 register.
This is to avoid updating the shadow registers while writing new values in the preload
registers. Then no update event occurs until the UDIS bit has been written to 0. However,
the counter restarts from 0, as well as the counter of the prescaler (but the prescale rate
does not change). In addition, if the URS bit (update request selection) in TIMx_CR1
register is set, setting the UG bit generates an update event UEV but without setting the UIF
flag (thus no interrupt or DMA request is sent). This is to avoid generating both update and
capture interrupts when clearing the counter on the capture event.
When an update event occurs, all the registers are updated and the update flag (UIF bit in
TIMx_SR register) is set (depending on the URS bit):
•
The buffer of the prescaler is reloaded with the preload value (content of the TIMx_PSC
register)
•
The auto-reload shadow register is updated with the preload value (TIMx_ARR)
The following figures show some examples of the counter behavior for different clock
frequencies when TIMx_ARR=0x36.
286/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Figure 91. Counter timing diagram, internal clock divided by 1
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 92. Counter timing diagram, internal clock divided by 2
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 93. Counter timing diagram, internal clock divided by 4
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
06Y9
Doc ID16188 Rev 5
287/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Figure 94. Counter timing diagram, internal clock divided by N
&.B,17
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
06Y9
Figure 95. Counter timing diagram, Update event when ARPE=0 (TIMx_ARR not
preloaded)
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGUHJLVWHU
))
:ULWHDQHZYDOXHLQ7,0[B$55
06Y9
288/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Figure 96. Counter timing diagram, Update event when ARPE=1 (TIMx_ARR
preloaded)
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
) ) ) ) ) &RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGSUHORDGUHJLVWHU
$XWRUHORDGVKDGRZUHJLVWHU
)
)
:ULWHDQHZYDOXHLQ7,0[B$55
06Y9
Downcounting mode
In downcounting mode, the counter counts from the auto-reload value (content of the
TIMx_ARR register) down to 0, then restarts from the auto-reload value and generates a
counter underflow event.
An Update event can be generate at each counter underflow or by setting the UG bit in the
TIMx_EGR register (by software or by using the slave mode controller)
The UEV update event can be disabled by software by setting the UDIS bit in TIMx_CR1
register. This is to avoid updating the shadow registers while writing new values in the
preload registers. Then no update event occurs until UDIS bit has been written to 0.
However, the counter restarts from the current auto-reload value, whereas the counter of the
prescaler restarts from 0 (but the prescale rate doesn’t change).
In addition, if the URS bit (update request selection) in TIMx_CR1 register is set, setting the
UG bit generates an update event UEV but without setting the UIF flag (thus no interrupt or
DMA request is sent). This is to avoid generating both update and capture interrupts when
clearing the counter on the capture event.
When an update event occurs, all the registers are updated and the update flag (UIF bit in
TIMx_SR register) is set (depending on the URS bit):
•
The buffer of the prescaler is reloaded with the preload value (content of the TIMx_PSC
register).
•
The auto-reload active register is updated with the preload value (content of the
TIMx_ARR register). Note that the auto-reload is updated before the counter is
reloaded, so that the next period is the expected one.
The following figures show some examples of the counter behavior for different clock
frequencies when TIMx_ARR=0x36.
Doc ID16188 Rev 5
289/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Figure 97. Counter timing diagram, internal clock divided by 1
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHUXQGHUIORZFQWBXGI
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
06Y9
Figure 98. Counter timing diagram, internal clock divided by 2
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
06Y9
Figure 99. Counter timing diagram, internal clock divided by 4
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
290/713
Doc ID16188 Rev 5
069
RM0041
General-purpose timers (TIM2 to TIM5)
Figure 100. Counter timing diagram, internal clock divided by N
&.B,17
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 101. Counter timing diagram, Update event
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGSUHORDGUHJLVWHU
))
:ULWHDQHZYDOXHLQ7,0[B$55
069
Center-aligned mode (up/down counting)
In center-aligned mode, the counter counts from 0 to the auto-reload value (content of the
TIMx_ARR register) – 1, generates a counter overflow event, then counts from the autoreload value down to 1 and generates a counter underflow event. Then it restarts counting
from 0.
Center-aligned mode is active when the CMS bits in TIMx_CR1 register are not equal to
'00'. The Output compare interrupt flag of channels configured in output is set when: the
counter counts down (Center aligned mode 1, CMS = "01"), the counter counts up (Center
aligned mode 2, CMS = "10") the counter counts up and down (Center aligned mode 3,
CMS = "11").
Doc ID16188 Rev 5
291/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
In this mode, the direction bit (DIR from TIMx_CR1 register) cannot be written. It is updated
by hardware and gives the current direction of the counter.
The update event can be generated at each counter overflow and at each counter underflow
or by setting the UG bit in the TIMx_EGR register (by software or by using the slave mode
controller) also generates an update event. In this case, the counter restarts counting from
0, as well as the counter of the prescaler.
The UEV update event can be disabled by software by setting the UDIS bit in TIMx_CR1
register. This is to avoid updating the shadow registers while writing new values in the
preload registers. Then no update event occurs until the UDIS bit has been written to 0.
However, the counter continues counting up and down, based on the current auto-reload
value.
In addition, if the URS bit (update request selection) in TIMx_CR1 register is set, setting the
UG bit generates an update event UEV but without setting the UIF flag (thus no interrupt or
DMA request is sent). This is to avoid generating both update and capture interrupt when
clearing the counter on the capture event.
When an update event occurs, all the registers are updated and the update flag (UIF bit in
TIMx_SR register) is set (depending on the URS bit):
•
The buffer of the prescaler is reloaded with the preload value (content of the TIMx_PSC
register).
•
The auto-reload active register is updated with the preload value (content of the
TIMx_ARR register). Note that if the update source is a counter overflow, the autoreload is updated before the counter is reloaded, so that the next period is the expected
one (the counter is loaded with the new value).
The following figures show some examples of the counter behavior for different clock
frequencies.
Figure 102. Counter timing diagram, internal clock divided by 1, TIMx_ARR=0x6
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
1. Here, center-aligned mode 1 is used, for more details refer to Section 13.4.1: TIMx control register 1 (TIMx_CR1).
292/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Figure 103. Counter timing diagram, internal clock divided by 2
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 104. Counter timing diagram, internal clock divided by 4, TIMx_ARR=0x36
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZFQWBRYI
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
1. Center-aligned mode 2 or 3 is used with an UIF on overflow.
Figure 105. Counter timing diagram, internal clock divided by N
&.B,17
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Doc ID16188 Rev 5
293/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Figure 106. Counter timing diagram, Update event with ARPE=1 (counter underflow)
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHUXQGHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGSUHORDGUHJLVWHU
)'
:ULWHDQHZYDOXHLQ7,0[B$55
$XWRUHORDGDFWLYHUHJLVWHU
)'
069
Figure 107. Counter timing diagram, Update event with ARPE=1 (counter overflow)
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
) ) )$ )% )& )
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGSUHORDGUHJLVWHU
)'
:ULWHDQHZYDOXHLQ7,0[B$55
$XWRUHORDGDFWLYHUHJLVWHU
)'
069
13.3.3
Clock selection
The counter clock can be provided by the following clock sources:
294/713
•
Internal clock (CK_INT)
•
External clock mode1: external input pin (TIx)
•
External clock mode2: external trigger input (ETR).
•
Internal trigger inputs (ITRx): using one timer as prescaler for another timer, for
example, Timer1 can be configured to act as a prescaler for Timer 2. Refer to Using
one timer as prescaler for another timer for more details.
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Internal clock source (CK_INT)
If the slave mode controller is disabled (SMS=000 in the TIMx_SMCR register), then the
CEN, DIR (in the TIMx_CR1 register) and UG bits (in the TIMx_EGR register) are actual
control bits and can be changed only by software (except UG which remains cleared
automatically). As soon as the CEN bit is written to 1, the prescaler is clocked by the internal
clock CK_INT.
Figure 108 shows the behavior of the control circuit and the upcounter in normal mode,
without prescaler.
Figure 108. Control circuit in normal mode, internal clock divided by 1
,QWHUQDOFORFN
&(1 &17B(1
8*
&17B,1,7
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
069
External clock source mode 1
This mode is selected when SMS=111 in the TIMx_SMCR register. The counter can count at
each rising or falling edge on a selected input.
Doc ID16188 Rev 5
295/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Figure 109. TI2 external clock connection example
7,0[B60&5
76>@
RU 7,)
7,)
,75[
7,B('
7,
)LOWHU
(GJH
GHWHFWRU
7,)B5LVLQJ
7,)B)DOOLQJ
7,)3
7,)3
(75)
RU
RU
[[
75*,
(75)
&.B,17
,&)>@
&&3
7,0[B&&05
7,0[B&&(5
LQWHUQDOFORFN
(QFRGHU
PRGH
([WHUQDOFORFN
PRGH
([WHUQDOFORFN
PRGH
&.B36&
,QWHUQDOFORFN
PRGH
(&(
606>@
7,0[B60&5
069
For example, to configure the upcounter to count in response to a rising edge on the TI2
input, use the following procedure:
Note:
1.
Configure channel 2 to detect rising edges on the TI2 input by writing CC2S= ‘01 in the
TIMx_CCMR1 register.
2.
Configure the input filter duration by writing the IC2F[3:0] bits in the TIMx_CCMR1
register (if no filter is needed, keep IC2F=0000).
The capture prescaler is not used for triggering, so there’s no need to configure it.
3.
Select rising edge polarity by writing CC2P=0 and CC2NP=0 in the TIMx_CCER
register.
4.
Configure the timer in external clock mode 1 by writing SMS=111 in the TIMx_SMCR
register.
5.
Select TI2 as the input source by writing TS=110 in the TIMx_SMCR register.
6.
Enable the counter by writing CEN=1 in the TIMx_CR1 register.
When a rising edge occurs on TI2, the counter counts once and the TIF flag is set.
The delay between the rising edge on TI2 and the actual clock of the counter is due to the
resynchronization circuit on TI2 input.
296/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Figure 110. Control circuit in external clock mode 1
7,
&17B(1
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
:ULWH7,) 069
External clock source mode 2
This mode is selected by writing ECE=1 in the TIMx_SMCR register.
The counter can count at each rising or falling edge on the external trigger input ETR.
Figure 111 gives an overview of the external trigger input block.
Figure 111. External trigger input block
RU 7,)
7,)
(75
(75SLQ
'LYLGHU
(73
(736>@
(753
&.B,17
7,0[B60&5 7,0[B60&5
)LOWHU
GRZQFRXQWHU
(7)>@
RU
RU
(QFRGHU
PRGH
75*,
([WHUQDOFORFN
&.B36&
PRGH
(75)
([WHUQDOFORFN
PRGH
&.B,17
,QWHUQDOFORFN
LQWHUQDOFORFN PRGH
7,0[B60&5
(&( 606>@
7,0[B60&5
069
For example, to configure the upcounter to count each 2 rising edges on ETR, use the
following procedure:
1.
As no filter is needed in this example, write ETF[3:0]=0000 in the TIMx_SMCR register.
2.
Set the prescaler by writing ETPS[1:0]=01 in the TIMx_SMCR register
3.
Select rising edge detection on the ETR pin by writing ETP=0 in the TIMx_SMCR
register
4.
Enable external clock mode 2 by writing ECE=1 in the TIMx_SMCR register.
5.
Enable the counter by writing CEN=1 in the TIMx_CR1 register.
The counter counts once each 2 ETR rising edges.
Doc ID16188 Rev 5
297/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
The delay between the rising edge on ETR and the actual clock of the counter is due to the
resynchronization circuit on the ETRP signal.
Figure 112. Control circuit in external clock mode 2
&.B,17
&17B(1
(75
(753
(75)
&RXQWHUFORFN &.B,17 &.B36&
&RXQWHUUHJLVWHU
069
13.3.4
Capture/compare channels
Each Capture/Compare channel (see Figure 113) is built around a capture/compare register
(including a shadow register), an input stage for capture (with digital filter, multiplexing and
prescaler) and an output stage (with comparator and output control).
The input stage samples the corresponding TIx input to generate a filtered signal TIxF.
Then, an edge detector with polarity selection generates a signal (TIxFPx) which can be
used as trigger input by the slave mode controller or as the capture command. It is
prescaled before the capture register (ICxPS).
Figure 113. Capture/compare channel (example: channel 1 input stage)
7,)B('
7RWKHVODYHPRGHFRQWUROOHU
7,
I'76
7,)B5LVLQJ
)LOWHU
7,)
GRZQFRXQWHU
(GJH
GHWHFWRU
7,)B)DOOLQJ
7,)3
7,)3
,&)>@
7,0[B&&05
&&3&&13
7,0[B&&(5
7,)B5LVLQJ
IURPFKDQQHO
7,)B)DOOLQJ
IURPFKDQQHO
75&
IURPVODYHPRGH
FRQWUROOHU
,&
,&36
'LYLGHU
&&6>@ ,&36>@
&&(
7,0[B&&05
7,0[B&&(5
069
298/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
The output stage generates an intermediate waveform which is then used for reference:
OCxRef (active high). The polarity acts at the end of the chain.
Figure 114. Capture/compare channel 1 main circuit
$3%%XV
5HDG&&5+ 6
5HDG&&5/
KLJK
UHDGBLQBSURJUHVV
&&6>@
,QSXW
PRGH
6 ZULWH&&5+
ZULWHBLQBSURJUHVV
&DSWXUHFRPSDUHSUHORDGUHJLVWHU
ZULWH&&5/
5
5
FRPSDUHBWUDQVIHU
FDSWXUHBWUDQVIHU
&&6>@
ORZ
LIELW
0&8SHULSKHUDOLQWHUIDFH
2XWSXW
PRGH
&&6>@
&&6>@
2&3(
&DSWXUHFRPSDUHVKDGRZUHJLVWHU
&RPSDUDWRU
&DSWXUH
,&36
8(9
&&(
&17!&&5
&RXQWHU
IURPWLPH
EDVHXQLW
2&3(
7,0[B&&05
&17 &&5
&&*
7,0[B(*5
069
Figure 115. Output stage of capture/compare channel (channel 1)
KZ&ͺ>Z
dZ&
Ϭ
KZ&ͺ>Zͺ/Ed
ϭ
dŽƚŚĞŵĂƐƚĞƌŵŽĚĞ
ĐŽŶƚƌŽůůĞƌ
Ϭ
K^
ϭ
d/Ddžͺ^DZ
EdхZϭ
EdсZϭ
KƵƚƉƵƚ
ŶĂďůĞ
ŝƌĐƵŝƚ
Kϭ
ϭW
KƵƚƉƵƚŵŽĚĞ
ĐŽŶƚƌŽůůĞƌ
ŽĐϭƌĞĨ
d/DdžͺZ
ϭ
d/DdžͺZ
KϭD΀Ϯ͗Ϭ΁
d/DdžͺDZϭ
Ăŝϭϳϭϴϳ
The capture/compare block is made of one preload register and one shadow register. Write
and read always access the preload register.
In capture mode, captures are actually done in the shadow register, which is copied into the
preload register.
In compare mode, the content of the preload register is copied into the shadow register
which is compared to the counter.
Doc ID16188 Rev 5
299/713
339
General-purpose timers (TIM2 to TIM5)
13.3.5
RM0041
Input capture mode
In Input capture mode, the Capture/Compare Registers (TIMx_CCRx) are used to latch the
value of the counter after a transition detected by the corresponding ICx signal. When a
capture occurs, the corresponding CCXIF flag (TIMx_SR register) is set and an interrupt or
a DMA request can be sent if they are enabled. If a capture occurs while the CCxIF flag was
already high, then the over-capture flag CCxOF (TIMx_SR register) is set. CCxIF can be
cleared by software by writing it to 0 or by reading the captured data stored in the
TIMx_CCRx register. CCxOF is cleared when written to 0.
The following example shows how to capture the counter value in TIMx_CCR1 when TI1
input rises. To do this, use the following procedure:
•
Select the active input: TIMx_CCR1 must be linked to the TI1 input, so write the CC1S
bits to 01 in the TIMx_CCMR1 register. As soon as CC1S becomes different from 00,
the channel is configured in input and the TIMx_CCR1 register becomes read-only.
•
Program the needed input filter duration with respect to the signal connected to the
timer (by programming the ICxF bits in the TIMx_CCMRx register if the input is one of
the TIx inputs). Let’s imagine that, when toggling, the input signal is not stable during at
must five internal clock cycles. We must program a filter duration longer than these five
clock cycles. We can validate a transition on TI1 when eight consecutive samples with
the new level have been detected (sampled at fDTS frequency). Then write IC1F bits to
0011 in the TIMx_CCMR1 register.
•
Select the edge of the active transition on the TI1 channel by writing the CC1P bit to 0
in the TIMx_CCER register (rising edge in this case).
•
Program the input prescaler. In our example, we wish the capture to be performed at
each valid transition, so the prescaler is disabled (write IC1PS bits to 00 in the
TIMx_CCMR1 register).
•
Enable capture from the counter into the capture register by setting the CC1E bit in the
TIMx_CCER register.
•
If needed, enable the related interrupt request by setting the CC1IE bit in the
TIMx_DIER register, and/or the DMA request by setting the CC1DE bit in the
TIMx_DIER register.
When an input capture occurs:
•
The TIMx_CCR1 register gets the value of the counter on the active transition.
•
CC1IF flag is set (interrupt flag). CC1OF is also set if at least two consecutive captures
occurred whereas the flag was not cleared.
•
An interrupt is generated depending on the CC1IE bit.
•
A DMA request is generated depending on the CC1DE bit.
In order to handle the overcapture, it is recommended to read the data before the
overcapture flag. This is to avoid missing an overcapture which could happen after reading
the flag and before reading the data.
Note:
300/713
IC interrupt and/or DMA requests can be generated by software by setting the
corresponding CCxG bit in the TIMx_EGR register.
Doc ID16188 Rev 5
RM0041
13.3.6
General-purpose timers (TIM2 to TIM5)
PWM input mode
This mode is a particular case of input capture mode. The procedure is the same except:
•
Two ICx signals are mapped on the same TIx input.
•
These 2 ICx signals are active on edges with opposite polarity.
•
One of the two TIxFP signals is selected as trigger input and the slave mode controller
is configured in reset mode.
For example, the user can measure the period (in TIMx_CCR1 register) and the duty cycle
(in TIMx_CCR2 register) of the PWM applied on TI1 using the following procedure
(depending on CK_INT frequency and prescaler value):
•
Select the active input for TIMx_CCR1: write the CC1S bits to 01 in the TIMx_CCMR1
register (TI1 selected).
•
Select the active polarity for TI1FP1 (used both for capture in TIMx_CCR1 and counter
clear): write the CC1P to ‘0’ (active on rising edge).
•
Select the active input for TIMx_CCR2: write the CC2S bits to 10 in the TIMx_CCMR1
register (TI1 selected).
•
Select the active polarity for TI1FP2 (used for capture in TIMx_CCR2): write the CC2P
bit to ‘1’ (active on falling edge).
•
Select the valid trigger input: write the TS bits to 101 in the TIMx_SMCR register
(TI1FP1 selected).
•
Configure the slave mode controller in reset mode: write the SMS bits to 100 in the
TIMx_SMCR register.
•
Enable the captures: write the CC1E and CC2E bits to ‘1 in the TIMx_CCER register.
Figure 116. PWM input mode timing
TI1
TIMx_CNT
0004
0000
0001
0002
TIMx_CCR1
0004
TIMx_CCR2
0002
IC1 capture
IC2 capture
reset counter
0003
0004
IC2 capture
pulse width
measurement
0000
IC1 capture
period
measurement
ai15413
13.3.7
Forced output mode
In output mode (CCxS bits = 00 in the TIMx_CCMRx register), each output compare signal
(OCxREF and then OCx) can be forced to active or inactive level directly by software,
independently of any comparison between the output compare register and the counter.
To force an output compare signal (ocxref/OCx) to its active level, the user just needs to
write 101 in the OCxM bits in the corresponding TIMx_CCMRx register. Thus ocxref is
Doc ID16188 Rev 5
301/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
forced high (OCxREF is always active high) and OCx get opposite value to CCxP polarity
bit.
e.g.: CCxP=0 (OCx active high) => OCx is forced to high level.
ocxref signal can be forced low by writing the OCxM bits to 100 in the TIMx_CCMRx
register.
Anyway, the comparison between the TIMx_CCRx shadow register and the counter is still
performed and allows the flag to be set. Interrupt and DMA requests can be sent
accordingly. This is described in the Output Compare Mode section.
13.3.8
Output compare mode
This function is used to control an output waveform or indicating when a period of time has
elapsed.
When a match is found between the capture/compare register and the counter, the output
compare function:
•
Assigns the corresponding output pin to a programmable value defined by the output
compare mode (OCxM bits in the TIMx_CCMRx register) and the output polarity (CCxP
bit in the TIMx_CCER register). The output pin can keep its level (OCXM=000), be set
active (OCxM=001), be set inactive (OCxM=010) or can toggle (OCxM=011) on match.
•
Sets a flag in the interrupt status register (CCxIF bit in the TIMx_SR register).
•
Generates an interrupt if the corresponding interrupt mask is set (CCXIE bit in the
TIMx_DIER register).
•
Sends a DMA request if the corresponding enable bit is set (CCxDE bit in the
TIMx_DIER register, CCDS bit in the TIMx_CR2 register for the DMA request
selection).
The TIMx_CCRx registers can be programmed with or without preload registers using the
OCxPE bit in the TIMx_CCMRx register.
In output compare mode, the update event UEV has no effect on ocxref and OCx output.
The timing resolution is one count of the counter. Output compare mode can also be used to
output a single pulse (in One-pulse mode).
Procedure:
1.
Select the counter clock (internal, external, prescaler).
2.
Write the desired data in the TIMx_ARR and TIMx_CCRx registers.
3.
Set the CCxIE and/or CCxDE bits if an interrupt and/or a DMA request is to be
generated.
4.
Select the output mode. For example, the user must write OCxM=011, OCxPE=0,
CCxP=0 and CCxE=1 to toggle OCx output pin when CNT matches CCRx, CCRx
preload is not used, OCx is enabled and active high.
5.
Enable the counter by setting the CEN bit in the TIMx_CR1 register.
The TIMx_CCRx register can be updated at any time by software to control the output
waveform, provided that the preload register is not enabled (OCxPE=0, else TIMx_CCRx
shadow register is updated only at the next update event UEV). An example is given in
Figure 117.
302/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Figure 117. Output compare mode, toggle on OC1
:ULWH%KLQWKH&&5UHJLVWHU
7,0[B&17
7,0[B&&5
$
%
%
%
%
$
2&5() 2&
0DWFKGHWHFWHGRQ&&5
,QWHUUXSWJHQHUDWHGLIHQDEOHG
069
13.3.9
PWM mode
Pulse width modulation mode allows generating a signal with a frequency determined by the
value of the TIMx_ARR register and a duty cycle determined by the value of the
TIMx_CCRx register.
The PWM mode can be selected independently on each channel (one PWM per OCx
output) by writing 110 (PWM mode 1) or ‘111 (PWM mode 2) in the OCxM bits in the
TIMx_CCMRx register. The user must enable the corresponding preload register by setting
the OCxPE bit in the TIMx_CCMRx register, and eventually the auto-reload preload register
by setting the ARPE bit in the TIMx_CR1 register.
As the preload registers are transferred to the shadow registers only when an update event
occurs, before starting the counter, the user has to initialize all the registers by setting the
UG bit in the TIMx_EGR register.
OCx polarity is software programmable using the CCxP bit in the TIMx_CCER register. It
can be programmed as active high or active low. OCx output is enabled by the CCxE bit in
the TIMx_CCER register. Refer to the TIMx_CCERx register description for more details.
In PWM mode (1 or 2), TIMx_CNT and TIMx_CCRx are always compared to determine
whether TIMx_CCRx≤TIMx_CNT or TIMx_CNT≤TIMx_CCRx (depending on the direction of
the counter). However, to comply with the ETRF (OCREF can be cleared by an external
event through the ETR signal until the next PWM period), the OCREF signal is asserted
only:
•
When the result of the comparison changes, or
•
When the output compare mode (OCxM bits in TIMx_CCMRx register) switches from
the “frozen” configuration (no comparison, OCxM=‘000) to one of the PWM modes
(OCxM=‘110 or ‘111).
This forces the PWM by software while the timer is running.
The timer is able to generate PWM in edge-aligned mode or center-aligned mode
depending on the CMS bits in the TIMx_CR1 register.
Doc ID16188 Rev 5
303/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
PWM edge-aligned mode
Upcounting configuration
Upcounting is active when the DIR bit in the TIMx_CR1 register is low. Refer to Upcounting
mode.
In the following example, we consider PWM mode 1. The reference PWM signal OCxREF is
high as long as TIMx_CNT <TIMx_CCRx else it becomes low. If the compare value in
TIMx_CCRx is greater than the auto-reload value (in TIMx_ARR) then OCxREF is held at ‘1.
If the compare value is 0 then OCxREF is held at ‘0. Figure 118 shows some edge-aligned
PWM waveforms in an example where TIMx_ARR=8.
Figure 118. Edge-aligned PWM waveforms (ARR=8)
&RXQWHUUHJLVWHU
&&5[ 2&;5()
&&[,)
2&;5()
&&5[ &&[,)
2&;5()
µ¶
&&5[!
&&[,)
2&;5()
µ¶
&&5[ &&[,)
069
Downcounting configuration
Downcounting is active when DIR bit in TIMx_CR1 register is high. Refer to Downcounting
mode.
In PWM mode 1, the reference signal ocxref is low as long as TIMx_CNT>TIMx_CCRx else
it becomes high. If the compare value in TIMx_CCRx is greater than the auto-reload value in
TIMx_ARR, then ocxref is held at ‘1. 0% PWM is not possible in this mode.
PWM center-aligned mode
Center-aligned mode is active when the CMS bits in TIMx_CR1 register are different from
‘00 (all the remaining configurations having the same effect on the ocxref/OCx signals). The
compare flag is set when the counter counts up, when it counts down or both when it counts
up and down depending on the CMS bits configuration. The direction bit (DIR) in the
304/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
TIMx_CR1 register is updated by hardware and must not be changed by software. Refer to
Center-aligned mode (up/down counting).
Figure 119 shows some center-aligned PWM waveforms in an example where:
•
TIMx_ARR=8,
•
PWM mode is the PWM mode 1,
•
The flag is set when the counter counts down corresponding to the center-aligned
mode 1 selected for CMS=01 in TIMx_CR1 register.
Figure 119. Center-aligned PWM waveforms (ARR=8)
#OUNTERREGISTER
/#X2%&
##2X
#-3
#-3
#-3
##X)&
/#X2%&
##2X
#-3OR
##X)&
/#X2%&
##2X
gg
#-3
#-3
#-3
##X)&
/#X2%&
##2X
gg
#-3
#-3
#-3
##X)&
/#X2%&
##2X
##X)&
gg
#-3
#-3
#-3
AIB
Hints on using center-aligned mode:
•
When starting in center-aligned mode, the current up-down configuration is used. It
means that the counter counts up or down depending on the value written in the DIR bit
Doc ID16188 Rev 5
305/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
in the TIMx_CR1 register. Moreover, the DIR and CMS bits must not be changed at the
same time by the software.
•
•
13.3.10
Writing to the counter while running in center-aligned mode is not recommended as it
can lead to unexpected results. In particular:
–
The direction is not updated if the user writes a value in the counter that is greater
than the auto-reload value (TIMx_CNT>TIMx_ARR). For example, if the counter
was counting up, it continues to count up.
–
The direction is updated if the user writes 0 or write the TIMx_ARR value in the
counter but no Update Event UEV is generated.
The safest way to use center-aligned mode is to generate an update by software
(setting the UG bit in the TIMx_EGR register) just before starting the counter and not to
write the counter while it is running.
One-pulse mode
One-pulse mode (OPM) is a particular case of the previous modes. It allows the counter to
be started in response to a stimulus and to generate a pulse with a programmable length
after a programmable delay.
Starting the counter can be controlled through the slave mode controller. Generating the
waveform can be done in output compare mode or PWM mode. Select One-pulse mode by
setting the OPM bit in the TIMx_CR1 register. This makes the counter stop automatically at
the next update event UEV.
A pulse can be correctly generated only if the compare value is different from the counter
initial value. Before starting (when the timer is waiting for the trigger), the configuration must
be:
•
In upcounting: CNT<CCRx≤ARR (in particular, 0<CCRx),
•
In downcounting: CNT>CCRx.
Figure 120. Example of one-pulse mode
7,
2&5()
2&
&RXQWHU
7,0B$55
7,0B&&5
W'(/$<
W38/6(
W
069
For example the user may want to generate a positive pulse on OC1 with a length of tPULSE
and after a delay of tDELAY as soon as a positive edge is detected on the TI2 input pin.
306/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Let’s use TI2FP2 as trigger 1:
•
Map TI2FP2 on TI2 by writing CC2S=01 in the TIMx_CCMR1 register.
•
TI2FP2 must detect a rising edge, write CC2P=0 in the TIMx_CCER register.
•
Configure TI2FP2 as trigger for the slave mode controller (TRGI) by writing TS=110 in
the TIMx_SMCR register.
•
TI2FP2 is used to start the counter by writing SMS to ‘110 in the TIMx_SMCR register
(trigger mode).
The OPM waveform is defined by writing the compare registers (taking into account the
clock frequency and the counter prescaler).
•
The tDELAY is defined by the value written in the TIMx_CCR1 register.
•
The tPULSE is defined by the difference between the auto-reload value and the compare
value (TIMx_ARR - TIMx_CCR + 1).
•
Let us say user wants to build a waveform with a transition from ‘0 to ‘1 when a
compare match occurs and a transition from ‘1 to ‘0 when the counter reaches the
auto-reload value. To do this enable PWM mode 2 by writing OC1M=111 in the
TIMx_CCMR1 register. The user can optionally enable the preload registers by writing
OC1PE=1 in the TIMx_CCMR1 register and ARPE in the TIMx_CR1 register. In this
case write the compare value in the TIMx_CCR1 register, the auto-reload value in the
TIMx_ARR register, generate an update by setting the UG bit and wait for external
trigger event on TI2. CC1P is written to ‘0 in this example.
In our example, the DIR and CMS bits in the TIMx_CR1 register should be low.
User only wants one pulse (Single mode), so write '1 in the OPM bit in the TIMx_CR1
register to stop the counter at the next update event (when the counter rolls over from the
auto-reload value back to 0). When OPM bit in the TIMx_CR1 register is set to '0', so the
Repetitive Mode is selected.
Particular case: OCx fast enable:
In One-pulse mode, the edge detection on TIx input set the CEN bit which enables the
counter. Then the comparison between the counter and the compare value makes the
output toggle. But several clock cycles are needed for these operations and it limits the
minimum delay tDELAY min we can get.
To output a waveform with the minimum delay, the user can set the OCxFE bit in the
TIMx_CCMRx register. Then OCxRef (and OCx) is forced in response to the stimulus,
without taking in account the comparison. Its new level is the same as if a compare match
had occurred. OCxFE acts only if the channel is configured in PWM1 or PWM2 mode.
13.3.11
Clearing the OCxREF signal on an external event
The OCxREF signal for a given channel can be driven Low by applying a High level to the
ETRF input (OCxCE enable bit of the corresponding TIMx_CCMRx register set to '1'). The
OCxREF signal remains Low until the next update event, UEV, occurs.
This function can only be used in output compare and PWM modes, and does not work in
forced mode.
For example, the ETR signal can be connected to the output of a comparator to be used for
current handling. In this case, ETR must be configured as follows:
Doc ID16188 Rev 5
307/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
1.
The external trigger prescaler should be kept off: bits ETPS[1:0] in the TIMx_SMCR
register are cleared to 00.
2.
The external clock mode 2 must be disabled: bit ECE in the TIM1_SMCR register is
cleared to 0.
3.
The external trigger polarity (ETP) and the external trigger filter (ETF) can be
configured according to the application’s needs.
Figure 121 shows the behavior of the OCxREF signal when the ETRF input becomes high,
for both values of the OCxCE enable bit. In this example, the timer TIMx is programmed in
PWM mode.
Figure 121. Clearing TIMx OCxREF
&&5[
&RXQWHU&17
(75)
2&[5()2&[&( µ¶
2&[5()2&[&( µ¶
(75)EHFRPHVKLJK
(75)VWLOOKLJK
069
Note:
In case of a PWM with a 100% duty cycle (if CCRx>ARR), OCxREF is enabled again at the
next counter overflow.
13.3.12
Encoder interface mode
To select Encoder Interface mode write SMS=‘001 in the TIMx_SMCR register if the counter
is counting on TI2 edges only, SMS=010 if it is counting on TI1 edges only and SMS=011 if
it is counting on both TI1 and TI2 edges.
Select the TI1 and TI2 polarity by programming the CC1P and CC2P bits in the TIMx_CCER
register. CC1NP and CC2NP must be kept cleared. When needed, program the input filter
as well.
The two inputs TI1 and TI2 are used to interface to an incremental encoder. Refer to
Table 70. The counter is clocked by each valid transition on TI1FP1 or TI2FP2 (TI1 and TI2
after input filter and polarity selection, TI1FP1=TI1 if not filtered and not inverted,
TI2FP2=TI2 if not filtered and not inverted) assuming that it is enabled (CEN bit in
TIMx_CR1 register written to ‘1). The sequence of transitions of the two inputs is evaluated
and generates count pulses as well as the direction signal. Depending on the sequence the
counter counts up or down, the DIR bit in the TIMx_CR1 register is modified by hardware
accordingly. The DIR bit is calculated at each transition on any input (TI1 or TI2), whatever
the counter is counting on TI1 only, TI2 only or both TI1 and TI2.
Encoder interface mode acts simply as an external clock with direction selection. This
means that the counter just counts continuously between 0 and the auto-reload value in the
TIMx_ARR register (0 to ARR or ARR down to 0 depending on the direction). So the user
308/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
must configure TIMx_ARR before starting. In the same way, the capture, compare,
prescaler, trigger output features continue to work as normal.
In this mode, the counter is modified automatically following the speed and the direction of
the incremental encoder and its content, therefore, always represents the encoder’s
position. The count direction correspond to the rotation direction of the connected sensor.
The table summarizes the possible combinations, assuming TI1 and TI2 don’t switch at the
same time.
Table 70. Counting direction versus encoder signals
Level on opposite
signal (TI1FP1 for
TI2, TI2FP2 for TI1)
Rising
Falling
Rising
Falling
Counting on
TI1 only
High
Down
Up
No Count
No Count
Low
Up
Down
No Count
No Count
Counting on
TI2 only
High
No Count
No Count
Up
Down
Low
No Count
No Count
Down
Up
Counting on
TI1 and TI2
High
Down
Up
Up
Down
Low
Up
Down
Down
Up
Active edge
TI1FP1 signal
TI2FP2 signal
An external incremental encoder can be connected directly to the MCU without external
interface logic. However, comparators are normally be used to convert the encoder’s
differential outputs to digital signals. This greatly increases noise immunity. The third
encoder output which indicate the mechanical zero position, may be connected to an
external interrupt input and trigger a counter reset.
Figure 122 gives an example of counter operation, showing count signal generation and
direction control. It also shows how input jitter is compensated where both edges are
selected. This might occur if the sensor is positioned near to one of the switching points. For
this example we assume that the configuration is the following:
•
CC1S= ‘01’ (TIMx_CCMR1 register, TI1FP1 mapped on TI1)
•
CC2S= ‘01’ (TIMx_CCMR2 register, TI2FP2 mapped on TI2)
•
CC1P= ‘0’, CC1NP = ‘0’, IC1F =’0000’ (TIMx_CCER register, TI1FP1 noninverted,
TI1FP1=TI1)
•
CC2P= ‘0’, CC2NP = ‘0’, IC2F =’0000’ (TIMx_CCER register, TI2FP2 noninverted,
TI2FP2=TI2)
•
SMS= ‘011’ (TIMx_SMCR register, both inputs are active on both rising and falling
edges)
•
CEN = 1 (TIMx_CR1 register, Counter is enabled)
Doc ID16188 Rev 5
309/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Figure 122. Example of counter operation in encoder interface mode
IRUZDUG
MLWWHU
EDFNZDUG
MLWWHU
IRUZDUG
7,
7,
&RXQWHU
XS
GRZQ
XS
069
Figure 123 gives an example of counter behavior when TI1FP1 polarity is inverted (same
configuration as above except CC1P=1).
Figure 123. Example of encoder interface mode with TI1FP1 polarity inverted
IRUZDUG
MLWWHU
EDFNZDUG
MLWWHU
IRUZDUG
7,
7,
&RXQWHU
GRZQ
XS
GRZQ
069
The timer, when configured in Encoder Interface mode provides information on the sensor’s
current position. The user can obtain dynamic information (speed, acceleration,
deceleration) by measuring the period between two encoder events using a second timer
configured in capture mode. The output of the encoder which indicates the mechanical zero
can be used for this purpose. Depending on the time between two events, the counter can
also be read at regular times. The user can do this by latching the counter value into a third
input capture register if available (then the capture signal must be periodic and can be
generated by another timer). when available, it is also possible to read its value through a
DMA request generated by a Real-Time clock.
13.3.13
Timer input XOR function
The TI1S bit in the TIM1_CR2 register, allows the input filter of channel 1 to be connected to
the output of a XOR gate, combining the three input pins TIMx_CH1 to TIMx_CH3.
The XOR output can be used with all the timer input functions such as trigger or input
capture.
310/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
An example of this feature used to interface Hall sensors is given in Section 12.3.18.
13.3.14
Timers and external trigger synchronization
The TIMx Timers can be synchronized with an external trigger in several modes: Reset
mode, Gated mode and Trigger mode.
Slave mode: Reset mode
The counter and its prescaler can be reinitialized in response to an event on a trigger input.
Moreover, if the URS bit from the TIMx_CR1 register is low, an update event UEV is
generated. Then all the preloaded registers (TIMx_ARR, TIMx_CCRx) are updated.
In the following example, the upcounter is cleared in response to a rising edge on TI1 input:
•
Configure the channel 1 to detect rising edges on TI1. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC1F=0000). The capture
prescaler is not used for triggering, so the user does not need to configure it. The
CC1S bits select the input capture source only, CC1S = 01 in the TIMx_CCMR1
register. Write CC1P=0 and CC1NP=0 in TIMx_CCER register to validate the polarity
(and detect rising edges only).
•
Configure the timer in reset mode by writing SMS=100 in TIMx_SMCR register. Select
TI1 as the input source by writing TS=101 in TIMx_SMCR register.
•
Start the counter by writing CEN=1 in the TIMx_CR1 register.
The counter starts counting on the internal clock, then behaves normally until TI1 rising
edge. When TI1 rises, the counter is cleared and restarts from 0. In the meantime, the
trigger flag is set (TIF bit in the TIMx_SR register) and an interrupt request, or a DMA
request can be sent if enabled (depending on the TIE and TDE bits in TIMx_DIER register).
Figure 124 shows this behavior when the auto-reload register TIMx_ARR=0x36. The delay
between the rising edge on TI1 and the actual reset of the counter is due to the
resynchronization circuit on TI1 input.
Figure 124. Control circuit in reset mode
7,
8*
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
069
Slave mode: Gated mode
The counter can be enabled depending on the level of a selected input.
In the following example, the upcounter counts only when TI1 input is low:
•
Configure the channel 1 to detect low levels on TI1. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC1F=0000). The capture
Doc ID16188 Rev 5
311/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
prescaler is not used for triggering, so the user does not need to configure it. The
CC1S bits select the input capture source only, CC1S=01 in TIMx_CCMR1 register.
Write CC1P=1 and CC1NP=0 in TIMx_CCER register to validate the polarity (and
detect low level only).
•
Configure the timer in gated mode by writing SMS=101 in TIMx_SMCR register. Select
TI1 as the input source by writing TS=101 in TIMx_SMCR register.
•
Enable the counter by writing CEN=1 in the TIMx_CR1 register (in gated mode, the
counter doesn’t start if CEN=0, whatever is the trigger input level).
The counter starts counting on the internal clock as long as TI1 is low and stops as soon as
TI1 becomes high. The TIF flag in the TIMx_SR register is set both when the counter starts
or stops.
The delay between the rising edge on TI1 and the actual stop of the counter is due to the
resynchronization circuit on TI1 input.
Figure 125. Control circuit in gated mode
7,
&17B(1
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
:ULWH7,) 069
Note:
The configuration “CCxP=CCxNP=1” (detection of both rising and falling edges) does not
have any effect in gated mode because gated mode acts on a level and not on an edge.
Slave mode: Trigger mode
The counter can start in response to an event on a selected input.
In the following example, the upcounter starts in response to a rising edge on TI2 input:
•
Configure the channel 2 to detect rising edges on TI2. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC2F=0000). The capture
prescaler is not used for triggering, so the user does not need to configure it. CC2S bits
are selecting the input capture source only, CC2S=01 in TIMx_CCMR1 register. Write
CC2P=1 and CC2NP=0 in TIMx_CCER register to validate the polarity (and detect low
level only).
•
Configure the timer in trigger mode by writing SMS=110 in TIMx_SMCR register. Select
TI2 as the input source by writing TS=110 in TIMx_SMCR register.
When a rising edge occurs on TI2, the counter starts counting on the internal clock and the
TIF flag is set.
The delay between the rising edge on TI2 and the actual start of the counter is due to the
resynchronization circuit on TI2 input.
312/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Figure 126. Control circuit in trigger mode
7,
&17B(1
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
069
Slave mode: External Clock mode 2 + trigger mode
The external clock mode 2 can be used in addition to another slave mode (except external
clock mode 1 and encoder mode). In this case, the ETR signal is used as external clock
input, and another input can be selected as trigger input when operating in reset mode,
gated mode or trigger mode. It is recommended not to select ETR as TRGI through the TS
bits of TIMx_SMCR register.
In the following example, the upcounter is incremented at each rising edge of the ETR
signal as soon as a rising edge of TI1 occurs:
1.
2.
3.
Configure the external trigger input circuit by programming the TIMx_SMCR register as
follows:
–
ETF = 0000: no filter
–
ETPS = 00: prescaler disabled
–
ETP = 0: detection of rising edges on ETR and ECE=1 to enable the external clock
mode 2.
Configure the channel 1 as follows, to detect rising edges on TI:
–
IC1F = 0000: no filter.
–
The capture prescaler is not used for triggering and does not need to be
configured.
–
CC1S = 01 in TIMx_CCMR1 register to select only the input capture source
–
CC1P = 0 and CC1NP = 0 in TIMx_CCER register to validate the polarity (and
detect rising edge only).
Configure the timer in trigger mode by writing SMS=110 in TIMx_SMCR register. Select
TI1 as the input source by writing TS=101 in TIMx_SMCR register.
A rising edge on TI1 enables the counter and sets the TIF flag. The counter then counts on
ETR rising edges.
The delay between the rising edge of the ETR signal and the actual reset of the counter is
due to the resynchronization circuit on ETRP input.
Doc ID16188 Rev 5
313/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Figure 127. Control circuit in external clock mode 2 + trigger mode
7,
&(1&17B(1
(75
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
069
13.3.15
Timer synchronization
The TIMx timers are linked together internally for timer synchronization or chaining. When
one Timer is configured in Master Mode, it can reset, start, stop or clock the counter of
another Timer configured in Slave Mode.
Figure 128 presents an overview of the trigger selection and the master mode selection
blocks.
Note:
The clock of the slave timer must be enabled prior to receiving events from the master timer,
and must not be changed on-the-fly while triggers are received from the master timer.
Using one timer as prescaler for another timer
Figure 128. Master/Slave timer example
TIM3
TIM2
MMS
Clock
UEV
Master
mode
Prescaler
Counter
TS
TRGO1 ITR2
control
Slave
Doc ID16188 Rev 5
CK_PSC
mode
control
Input
trigger
selection
314/713
SMS
Prescaler
Counter
RM0041
General-purpose timers (TIM2 to TIM5)
For example, the user can configure TIM3 to act as a prescaler for TIM2. Refer to
Figure 128. To do this:
Note:
•
Configure TIM3 in master mode so that it outputs a periodic trigger signal on each
update event UEV. If MMS=010 is written in the TIM3_CR2 register, a rising edge is
output on TRGO1 each time an update event is generated.
•
To connect the TRGO1 output of TIM3 to TIM2, TIM2 must be configured in slave mode
using ITR2 as internal trigger. Select this through the TS bits in the TIM2_SMCR
register (writing TS=010).
•
Then put the slave mode controller in external clock mode 1 (write SMS=111 in the
TIM2_SMCR register). This causes TIM2 to be clocked by the rising edge of the
periodic TIM3 trigger signal (which correspond to the TIM3 counter overflow).
•
Finally both timers must be enabled by setting their respective CEN bits (TIMx_CR1
register).
If OCx is selected on TIM3 as the trigger output (MMS=1xx), its rising edge is used to clock
the counter of TIM2.
Using one timer to enable another timer
In this example, we control the enable of TIM2 with the output compare 1 of Timer 1. Refer
to Figure 128 for connections. TIM2 counts on the divided internal clock only when OC1REF
of TIM3 is high. Both counter clock frequencies are divided by 3 by the prescaler compared
to CK_INT (fCK_CNT = fCK_INT/3).
Note:
•
Configure TIM3 master mode to send its Output Compare 1 Reference (OC1REF)
signal as trigger output (MMS=100 in the TIM3_CR2 register).
•
Configure the TIM3 OC1REF waveform (TIM3_CCMR1 register).
•
Configure TIM2 to get the input trigger from TIM3 (TS=010 in the TIM2_SMCR
register).
•
Configure TIM2 in gated mode (SMS=101 in TIM2_SMCR register).
•
Enable TIM2 by writing ‘1 in the CEN bit (TIM2_CR1 register).
•
Start TIM3 by writing ‘1 in the CEN bit (TIM3_CR1 register).
The counter 2 clock is not synchronized with counter 1, this mode only affects the TIM2
counter enable signal.
Figure 129. Gating TIM2 with OC1REF of TIM3
CK_INT
TIM3-OC1REF
TIM3-CNT
TIM2-CNT
FC
FD
3045
FE
3046
FF
3047
00
01
3048
TIM2-TIF
Write TIF=0
In the example in Figure 129, the TIM2 counter and prescaler are not initialized before being
started. So they start counting from their current value. It is possible to start from a given
Doc ID16188 Rev 5
315/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
value by resetting both timers before starting TIM3. The user can then write any value in the
timer counters. The timers can easily be reset by software using the UG bit in the
TIMx_EGR registers.
In the next example, we synchronize TIM3 and TIM2. TIM3 is the master and starts from 0.
TIM2 is the slave and starts from 0xE7. The prescaler ratio is the same for both timers. TIM2
stops when TIM3 is disabled by writing ‘0 to the CEN bit in the TIM3_CR1 register:
•
Configure TIM3 master mode to send its Output Compare 1 Reference (OC1REF)
signal as trigger output (MMS=100 in the TIM3_CR2 register).
•
Configure the TIM3 OC1REF waveform (TIM3_CCMR1 register).
•
Configure TIM2 to get the input trigger from TIM3 (TS=000 in the TIM2_SMCR
register).
•
Configure TIM2 in gated mode (SMS=101 in TIM2_SMCR register).
•
Reset TIM3 by writing ‘1 in UG bit (TIM3_EGR register).
•
Reset TIM2 by writing ‘1 in UG bit (TIM2_EGR register).
•
Initialize TIM2 to 0xE7 by writing ‘0xE7’ in the TIM2 counter (TIM2_CNTL).
•
Enable TIM2 by writing ‘1 in the CEN bit (TIM2_CR1 register).
•
Start TIM3 by writing ‘1 in the CEN bit (TIM3_CR1 register).
•
Stop TIM3 by writing ‘0 in the CEN bit (TIM3_CR1 register).
Figure 130. Gating TIM2 with Enable of TIM3
CK_INT
TIM3-CEN=CNT_EN
TIM3-CNT_INIT
TIM3-CNT
TIM2-CNT
75
00
AB
00
E7
01
02
E8
E9
TIM2-CNT_INIT
TIM2
write CNT
TIM2-TIF
Write TIF=0
Using one timer to start another timer
In this example, we set the enable of Timer 2 with the update event of Timer 1. Refer to
Figure 128 for connections. Timer 2 starts counting from its current value (which can be
non-zero) on the divided internal clock as soon as the update event is generated by Timer 1.
When Timer 2 receives the trigger signal its CEN bit is automatically set and the counter
316/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
counts until we write ‘0 to the CEN bit in the TIM2_CR1 register. Both counter clock
frequencies are divided by 3 by the prescaler compared to CK_INT (fCK_CNT = fCK_INT/3).
•
Configure TIM3 master mode to send its Update Event (UEV) as trigger output
(MMS=010 in the TIM3_CR2 register).
•
Configure the TIM3 period (TIM3_ARR registers).
•
Configure TIM2 to get the input trigger from TIM3 (TS=000 in the TIM2_SMCR
register).
•
Configure TIM2 in trigger mode (SMS=110 in TIM2_SMCR register).
•
Start TIM3 by writing ‘1 in the CEN bit (TIM3_CR1 register).
Figure 131. Triggering TIM2 with update of TIM3
CK_INT
TIM3-UEV
TIM3-CNT
FD
FE
TIM2-CNT
00
FF
45
02
01
47
46
48
TIM2-CEN=CNT_EN
TIM2-TIF
Write TIF=0
As in the previous example, both counters can be initialized before starting counting.
Figure 132 shows the behavior with the same configuration as in Figure 131 but in trigger
mode instead of gated mode (SMS=110 in the TIM2_SMCR register).
Figure 132. Triggering TIM2 with Enable of TIM3
CK_INT
TIM3-CEN=CNT_EN
TIM3-CNT_INIT
TIM3-CNT
TIM2-CNT
75
00
CD
00
01
E7
E8
02
E9
EA
TIM2-CNT_INIT
TIM2
write CNT
TIM2-TIF
Write TIF=0
Doc ID16188 Rev 5
317/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Starting 2 timers synchronously in response to an external trigger
In this example, we set the enable of TIM3 when its TI1 input rises, and the enable of TIM2
with the enable of TIM3. Refer to Figure 128 for connections. To ensure the counters are
aligned, TIM3 must be configured in Master/Slave mode (slave with respect to TI1, master
with respect to TIM2):
•
Configure TIM3 master mode to send its Enable as trigger output (MMS=001 in the
TIM3_CR2 register).
•
Configure TIM1 slave mode to get the input trigger from TI1 (TS=100 in the
TIM3_SMCR register).
•
Configure TIM3 in trigger mode (SMS=110 in the TIM3_SMCR register).
•
Configure the TIM3 in Master/Slave mode by writing MSM=1 (TIM3_SMCR register).
•
Configure TIM2 to get the input trigger from TIM3 (TS=000 in the TIM2_SMCR
register).
•
Configure TIM2 in trigger mode (SMS=110 in the TIM2_SMCR register).
When a rising edge occurs on TI1 (TIM3), both counters starts counting synchronously on
the internal clock and both TIF flags are set.
Note:
In this example both timers are initialized before starting (by setting their respective UG
bits). Both counters starts from 0, but the user can easily insert an offset between them by
writing any of the counter registers (TIMx_CNT). The master/slave mode inserts a delay
between CNT_EN and CK_PSC on TIM3.
Figure 133. Triggering TIM3 and TIM2 with TIM3 TI1 input
CK_INT
TIM3-TI1
TIM3-CEN=CNT_EN
TIM3-CK_PSC
TIM3-CNT
00
01 02 03 04 05 06 07 08 09
00
01 02 03 04 05 06 07 08 09
TIM3-TIF
TIM2-CEN=CNT_EN
TIM2-CK_PSC
TIM2-CNT
TIM2-TIF
13.3.16
Debug mode
When the microcontroller enters debug mode (Cortex®-M3 core - halted), the TIMx counter
either continues to work normally or stops, depending on DBG_TIMx_STOP configuration
bit in DBGMCU module. For more details, refer to Section 25.15.2: Debug support for
timers, watchdog and I2C.
318/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
13.4
TIMx2 to TIM5 registers
Refer to Section: List of abbreviations for registers for a list of abbreviations used in register
descriptions.
The 32-bit peripheral registers have to be written by words (32 bits). All other peripheral
registers have to be written by half-words (16 bits) or words (32 bits). Read accesses can be
done by bytes (8 bits), half-words (16 bits) or words (32 bits).
13.4.1
TIMx control register 1 (TIMx_CR1)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
Reserved
11
10
9
8
CKD[1:0]
rw
7
6
ARPE
rw
rw
5
CMS
rw
rw
4
3
2
1
0
DIR
OPM
URS
UDIS
CEN
rw
rw
rw
rw
rw
Bits 15:10 Reserved, must be kept at reset value.
Bits 9:8 CKD: Clock division
This bit-field indicates the division ratio between the timer clock (CK_INT) frequency and
sampling clock used by the digital filters (ETR, TIx),
00: tDTS = tCK_INT
01: tDTS = 2 × tCK_INT
10: tDTS = 4 × tCK_INT
11: Reserved
Bit 7 ARPE: Auto-reload preload enable
0: TIMx_ARR register is not buffered
1: TIMx_ARR register is buffered
Bits 6:5 CMS: Center-aligned mode selection
00: Edge-aligned mode. The counter counts up or down depending on the direction bit
(DIR).
01: Center-aligned mode 1. The counter counts up and down alternatively. Output compare
interrupt flags of channels configured in output (CCxS=00 in TIMx_CCMRx register) are set
only when the counter is counting down.
10: Center-aligned mode 2. The counter counts up and down alternatively. Output compare
interrupt flags of channels configured in output (CCxS=00 in TIMx_CCMRx register) are set
only when the counter is counting up.
11: Center-aligned mode 3. The counter counts up and down alternatively. Output compare
interrupt flags of channels configured in output (CCxS=00 in TIMx_CCMRx register) are set
both when the counter is counting up or down.
Note: It is not allowed to switch from edge-aligned mode to center-aligned mode as long as
the counter is enabled (CEN=1)
Bit 4 DIR: Direction
0: Counter used as upcounter
1: Counter used as downcounter
Note: This bit is read only when the timer is configured in Center-aligned mode or Encoder
mode.
Bit 3 OPM: One-pulse mode
0: Counter is not stopped at update event
1: Counter stops counting at the next update event (clearing the bit CEN)
Doc ID16188 Rev 5
319/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Bit 2 URS: Update request source
This bit is set and cleared by software to select the UEV event sources.
0: Any of the following events generate an update interrupt or DMA request if enabled.
These events can be:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
1: Only counter overflow/underflow generates an update interrupt or DMA request if
enabled.
Bit 1 UDIS: Update disable
This bit is set and cleared by software to enable/disable UEV event generation.
0: UEV enabled. The Update (UEV) event is generated by one of the following events:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
Buffered registers are then loaded with their preload values.
1: UEV disabled. The Update event is not generated, shadow registers keep their value
(ARR, PSC, CCRx). However the counter and the prescaler are reinitialized if the UG bit is
set or if a hardware reset is received from the slave mode controller.
Bit 0 CEN: Counter enable
0: Counter disabled
1: Counter enabled
Note: External clock, gated mode and encoder mode can work only if the CEN bit has been
previously set by software. However trigger mode can set the CEN bit automatically by
hardware.
CEN is cleared automatically in one-pulse mode, when an update event occurs.
320/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
13.4.2
TIMx control register 2 (TIMx_CR2)
Address offset: 0x04
Reset value: 0x0000
15
14
13
12
11
Reserved
10
9
8
7
6
TI1S
rw
5
4
MMS[2:0]
rw
rw
3
CCDS
rw
rw
2
1
0
Reserved
Bits 15:8 Reserved, must be kept at reset value.
Bit 7 TI1S: TI1 selection
0: The TIMx_CH1 pin is connected to TI1 input
1: The TIMx_CH1, CH2 and CH3 pins are connected to the TI1 input (XOR combination)
See also Section 12.3.18: Interfacing with Hall sensors
Bits 6:4 MMS[2:0]: Master mode selection
These bits allow to select the information to be sent in master mode to slave timers for
synchronization (TRGO). The combination is as follows:
000: Reset - the UG bit from the TIMx_EGR register is used as trigger output (TRGO). If the
reset is generated by the trigger input (slave mode controller configured in reset mode) then
the signal on TRGO is delayed compared to the actual reset.
001: Enable - the Counter enable signal, CNT_EN, is used as trigger output (TRGO). It is
useful to start several timers at the same time or to control a window in which a slave timer is
enabled. The Counter Enable signal is generated by a logic OR between CEN control bit
and the trigger input when configured in gated mode.
When the Counter Enable signal is controlled by the trigger input, there is a delay on TRGO,
except if the master/slave mode is selected (see the MSM bit description in TIMx_SMCR
register).
010: Update - The update event is selected as trigger output (TRGO). For instance a master
timer can then be used as a prescaler for a slave timer.
011: Compare Pulse - The trigger output send a positive pulse when the CC1IF flag is to be
set (even if it was already high), as soon as a capture or a compare match occurred.
(TRGO)
100: Compare - OC1REF signal is used as trigger output (TRGO)
101: Compare - OC2REF signal is used as trigger output (TRGO)
110: Compare - OC3REF signal is used as trigger output (TRGO)
111: Compare - OC4REF signal is used as trigger output (TRGO)
Note: The clock of the slave timer and ADC must be enabled prior to receiving events from
the master timer, and must not be changed on-the-fly while triggers are received from
the master timer.
Bit 3 CCDS: Capture/compare DMA selection
0: CCx DMA request sent when CCx event occurs
1: CCx DMA requests sent when update event occurs
Bits 2:0 Reserved, must be kept at reset value.
Doc ID16188 Rev 5
321/713
339
General-purpose timers (TIM2 to TIM5)
13.4.3
RM0041
TIMx slave mode control register (TIMx_SMCR)
Address offset: 0x08
Reset value: 0x0000
15
14
ETP
ECE
13
rw
rw
12
11
ETPS[1:0]
rw
rw
10
9
8
ETF[3:0]
rw
rw
rw
7
6
MSM
rw
rw
5
4
TS[2:0]
rw
rw
3
2
OCCS
rw
rw
1
0
SMS[2:0]
rw
rw
rw
Bit 15 ETP: External trigger polarity
This bit selects whether ETR or ETR is used for trigger operations
0: ETR is non-inverted, active at high level or rising edge
1: ETR is inverted, active at low level or falling edge
Bit 14 ECE: External clock enable
This bit enables External clock mode 2
0: External clock mode 2 disabled
1: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF
signal.
1: Setting the ECE bit has the same effect as selecting external clock mode 1 with TRGI
connected to ETRF (SMS=111 and TS=111).
2: It is possible to simultaneously use external clock mode 2 with the following slave modes:
reset mode, gated mode and trigger mode. Nevertheless, TRGI must not be connected to
ETRF in this case (TS bits must not be 111).
3: If external clock mode 1 and external clock mode 2 are enabled at the same time, the
external clock input is ETRF.
Bits 13:12 ETPS: External trigger prescaler
External trigger signal ETRP frequency must be at most 1/4 of CK_INT frequency. A
prescaler can be enabled to reduce ETRP frequency. It is useful when inputting fast external
clocks.
00: Prescaler OFF
01: ETRP frequency divided by 2
10: ETRP frequency divided by 4
11: ETRP frequency divided by 8
Bits 11:8 ETF[3:0]: External trigger filter
This bit-field then defines the frequency used to sample ETRP signal and the length of the
digital filter applied to ETRP. The digital filter is made of an event counter in which N
consecutive events are needed to validate a transition on the output:
0000: No filter, sampling is done at fDTS
0001: fSAMPLING=fCK_INT, N=2
0010: fSAMPLING=fCK_INT, N=4
0011: fSAMPLING=fCK_INT, N=8
0100: fSAMPLING=fDTS/2, N=6
0101: fSAMPLING=fDTS/2, N=8
0110: fSAMPLING=fDTS/4, N=6
0111: fSAMPLING=fDTS/4, N=8
1000: fSAMPLING=fDTS/8, N=6
1001: fSAMPLING=fDTS/8, N=8
1010: fSAMPLING=fDTS/16, N=5
1011: fSAMPLING=fDTS/16, N=6
1100: fSAMPLING=fDTS/16, N=8
1101: fSAMPLING=fDTS/32, N=5
1110: fSAMPLING=fDTS/32, N=6
1111: fSAMPLING=fDTS/32, N=8
322/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Bit 7 MSM: Master/Slave mode
0: No action
1: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect
synchronization between the current timer and its slaves (through TRGO). It is useful if we
want to synchronize several timers on a single external event.
Bits 6:4 TS: Trigger selection
This bit-field selects the trigger input to be used to synchronize the counter.
000: Internal Trigger 0 (ITR0).
001: Internal Trigger 1 (ITR1).
010: Internal Trigger 2 (ITR2).
011: Internal Trigger 3 (ITR3).
100: TI1 Edge Detector (TI1F_ED)
101: Filtered Timer Input 1 (TI1FP1)
110: Filtered Timer Input 2 (TI2FP2)
111: External Trigger input (ETRF)
See Table 71: TIMx internal trigger connection on page 324 for more details on ITRx
meaning for each Timer.
Note: These bits must be changed only when they are not used (e.g. when SMS=000) to
avoid wrong edge detections at the transition.
Bit 3 OCCS: OCREF clear selection
This bit is used to select the OCREF clear source
0: OCREF_CLR_INT is connected to the OCREF_CLR input
1: OCREF_CLR_INT is connected to ETRF
Bits 2:0 SMS: Slave mode selection
When external signals are selected the active edge of the trigger signal (TRGI) is linked to
the polarity selected on the external input (see Input Control register and Control Register
description.
000: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal
clock.
001: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2
level.
010: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1
level.
011: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges
depending on the level of the other input.
100: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter
and generates an update of the registers.
101: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The
counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of
the counter are controlled.
110: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not
reset). Only the start of the counter is controlled.
111: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.
Note: The gated mode must not be used if TI1F_ED is selected as the trigger input (TS=100).
Indeed, TI1F_ED outputs 1 pulse for each transition on TI1F, whereas the gated mode
checks the level of the trigger signal.
The clock of the slave timer must be enabled prior to receiving events from the master
timer, and must not be changed on-the-fly while triggers are received from the master
timer.
Doc ID16188 Rev 5
323/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Table 71. TIMx internal trigger connection
13.4.4
Slave TIM
ITR0 (TS = 000)
ITR1 (TS = 001)
ITR2 (TS = 010)
ITR3 (TS = 011)
TIM2
TIM1
TIM15
TIM3
TIM4
TIM3
TIM1
TIM2
TIM15
TIM4
TIM4
TIM1
TIM2
TIM3
TIM15
TIMx DMA/Interrupt enable register (TIMx_DIER)
Address offset: 0x0C
Reset value: 0x0000
15
Res.
14
TDE
rw
13
Res
12
11
10
9
8
CC4DE CC3DE CC2DE CC1DE
rw
rw
rw
rw
UDE
rw
7
Res.
6
TIE
rw
Bit 15 Reserved, must be kept at reset value.
Bit 14 TDE: Trigger DMA request enable
0: Trigger DMA request disabled
1: Trigger DMA request enabled
Bit 13 Reserved, must be kept at reset value.
Bit 12 CC4DE: Capture/Compare 4 DMA request enable
0: CC4 DMA request disabled
1: CC4 DMA request enabled
Bit 11 CC3DE: Capture/Compare 3 DMA request enable
0: CC3 DMA request disabled
1: CC3 DMA request enabled
Bit 10 CC2DE: Capture/Compare 2 DMA request enable
0: CC2 DMA request disabled
1: CC2 DMA request enabled
Bit 9 CC1DE: Capture/Compare 1 DMA request enable
0: CC1 DMA request disabled
1: CC1 DMA request enabled
Bit 8 UDE: Update DMA request enable
0: Update DMA request disabled
1: Update DMA request enabled
Bit 7 Reserved, must be kept at reset value.
Bit 6 TIE: Trigger interrupt enable
0: Trigger interrupt disabled
1: Trigger interrupt enabled
Bit 5 Reserved, must be kept at reset value.
Bit 4 CC4IE: Capture/Compare 4 interrupt enable
0: CC4 interrupt disabled
1: CC4 interrupt enabled
324/713
Doc ID16188 Rev 5
5
Res
4
3
2
1
0
CC4IE
CC3IE
CC2IE
CC1IE
UIE
rw
rw
rw
rw
rw
RM0041
General-purpose timers (TIM2 to TIM5)
Bit 3 CC3IE: Capture/Compare 3 interrupt enable
0: CC3 interrupt disabled
1: CC3 interrupt enabled
Bit 2 CC2IE: Capture/Compare 2 interrupt enable
0: CC2 interrupt disabled
1: CC2 interrupt enabled
Bit 1 CC1IE: Capture/Compare 1 interrupt enable
0: CC1 interrupt disabled
1: CC1 interrupt enabled
Bit 0 UIE: Update interrupt enable
0: Update interrupt disabled
1: Update interrupt enabled
13.4.5
TIMx status register (TIMx_SR)
Address offset: 0x10
Reset value: 0x0000
15
14
13
12
11
10
9
8
CC4OF CC3OF CC2OF CC1OF
Reserved
rc_w0
Bits 15:13
rc_w0
rc_w0
rc_w0
7
Reserved
6
TIF
rc_w0
5
Res
4
3
2
1
0
CC4IF
CC3IF
CC2IF
CC1IF
UIF
rc_w0
rc_w0
rc_w0
rc_w0
rc_w0
Reserved, must be kept at reset value.
Bit 12 CC4OF: Capture/Compare 4 overcapture flag
refer to CC1OF description
Bit 11 CC3OF: Capture/Compare 3 overcapture flag
refer to CC1OF description
Bit 10 CC2OF: Capture/compare 2 overcapture flag
refer to CC1OF description
Bit 9 CC1OF: Capture/Compare 1 overcapture flag
This flag is set by hardware only when the corresponding channel is configured in input
capture mode. It is cleared by software by writing it to ‘0.
0: No overcapture has been detected
1: The counter value has been captured in TIMx_CCR1 register while CC1IF flag was
already set
Bits 8:7
Reserved, must be kept at reset value.
Bit 6 TIF: Trigger interrupt flag
This flag is set by hardware on trigger event (active edge detected on TRGI input when the
slave mode controller is enabled in all modes but gated mode. It is set when the counter
starts or stops when gated mode is selected. It is cleared by software.
0: No trigger event occurred
1: Trigger interrupt pending
Bit 5
Reserved, must be kept at reset value.
Bit 4 CC4IF: Capture/Compare 4 interrupt flag
refer to CC1IF description
Doc ID16188 Rev 5
325/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Bit 3 CC3IF: Capture/Compare 3 interrupt flag
refer to CC1IF description
Bit 2 CC2IF: Capture/Compare 2 interrupt flag
refer to CC1IF description
Bit 1 CC1IF: Capture/compare 1 interrupt flag
If channel CC1 is configured as output:
This flag is set by hardware when the counter matches the compare value, with some
exception in center-aligned mode (refer to the CMS bits in the TIMx_CR1 register
description). It is cleared by software.
0: No match
1: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register.
When the contents of TIMx_CCR1 are greater than the contents of TIMx_ARR, the CC1IF bit
goes high on the counter overflow (in upcounting and up/down-counting modes) or underflow
(in downcounting mode)
If channel CC1 is configured as input:
This bit is set by hardware on a capture. It is cleared by software or by reading the
TIMx_CCR1 register.
0: No input capture occurred
1: The counter value has been captured in TIMx_CCR1 register (An edge has been detected
on IC1 which matches the selected polarity)
Bit 0 UIF: Update interrupt flag
This bit is set by hardware on an update event. It is cleared by software.
0: No update occurred
1: Update interrupt pending. This bit is set by hardware when the registers are updated:
At overflow or underflow (for TIM2 to TIM4) and if UDIS=0 in the TIMx_CR1 register.
When CNT is reinitialized by software using the UG bit in TIMx_EGR register, if URS=0 and
UDIS=0 in the TIMx_CR1 register.
When CNT is reinitialized by a trigger event (refer to the synchro control register description),
if URS=0 and UDIS=0 in the TIMx_CR1 register.
326/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
13.4.6
TIMx event generation register (TIMx_EGR)
Address offset: 0x14
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
TG
Reserved
w
5
Res.
4
3
2
1
0
CC4G
CC3G
CC2G
CC1G
UG
w
w
w
w
w
Bits 15:7 Reserved, must be kept at reset value.
Bit 6 TG: Trigger generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if
enabled.
Bit 5 Reserved, must be kept at reset value.
Bit 4 CC4G: Capture/compare 4 generation
refer to CC1G description
Bit 3 CC3G: Capture/compare 3 generation
refer to CC1G description
Bit 2 CC2G: Capture/compare 2 generation
refer to CC1G description
Bit 1 CC1G: Capture/compare 1 generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: A capture/compare event is generated on channel 1:
If channel CC1 is configured as output:
CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled.
If channel CC1 is configured as input:
The current value of the counter is captured in TIMx_CCR1 register. The CC1IF flag is set,
the corresponding interrupt or DMA request is sent if enabled. The CC1OF flag is set if the
CC1IF flag was already high.
Bit 0 UG: Update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action
1: Re-initialize the counter and generates an update of the registers. Note that the prescaler
counter is cleared too (anyway the prescaler ratio is not affected). The counter is cleared if
the center-aligned mode is selected or if DIR=0 (upcounting), else it takes the auto-reload
value (TIMx_ARR) if DIR=1 (downcounting).
Doc ID16188 Rev 5
327/713
339
General-purpose timers (TIM2 to TIM5)
13.4.7
RM0041
TIMx capture/compare mode register 1 (TIMx_CCMR1)
Address offset: 0x18
Reset value: 0x0000
The channels can be used in input (capture mode) or in output (compare mode). The
direction of a channel is defined by configuring the corresponding CCxS bits. All the other
bits of this register have a different function in input and in output mode. For a given bit,
OCxx describes its function when the channel is configured in output, ICxx describes its
function when the channel is configured in input. Take care that the same bit can have a
different meaning for the input stage and for the output stage.
15
14
OC2CE
13
12
OC2M[2:0]
IC2F[3:0]
rw
rw
rw
11
10
OC2PE OC2FE
IC2PSC[1:0]
rw
rw
rw
9
8
CC2S[1:0]
rw
7
6
OC1CE
rw
5
4
OC1M[2:0]
IC1F[3:0]
rw
rw
rw
3
2
OC1PE OC1FE
IC1PSC[1:0]
rw
rw
rw
1
0
CC1S[1:0]
rw
rw
Output compare mode
Bit 15 OC2CE: Output compare 2 clear enable
Bits 14:12 OC2M[2:0]: Output compare 2 mode
Bit 11 OC2PE: Output compare 2 preload enable
Bit 10 OC2FE: Output compare 2 fast enable
Bits 9:8 CC2S[1:0]: Capture/Compare 2 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output
01: CC2 channel is configured as input, IC2 is mapped on TI2
10: CC2 channel is configured as input, IC2 is mapped on TI1
11: CC2 channel is configured as input, IC2 is mapped on TRC. This mode is working only if
an internal trigger input is selected through the TS bit (TIMx_SMCR register)
Note: CC2S bits are writable only when the channel is OFF (CC2E = 0 in TIMx_CCER).
Bit 7 OC1CE: Output compare 1 clear enable
OC1CE: Output Compare 1 Clear Enable
0: OC1Ref is not affected by the ETRF input
1: OC1Ref is cleared as soon as a High level is detected on ETRF input
328/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Bits 6:4 OC1M: Output compare 1 mode
These bits define the behavior of the output reference signal OC1REF from which OC1 and
OC1N are derived. OC1REF is active high whereas OC1 and OC1N active level depends
on CC1P and CC1NP bits.
000: Frozen - The comparison between the output compare register TIMx_CCR1 and the
counter TIMx_CNT has no effect on the outputs.(this mode is used to generate a timing
base).
001: Set channel 1 to active level on match. OC1REF signal is forced high when the counter
TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
010: Set channel 1 to inactive level on match. OC1REF signal is forced low when the
counter TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
011: Toggle - OC1REF toggles when TIMx_CNT=TIMx_CCR1.
100: Force inactive level - OC1REF is forced low.
101: Force active level - OC1REF is forced high.
110: PWM mode 1 - In upcounting, channel 1 is active as long as TIMx_CNT<TIMx_CCR1
else inactive. In downcounting, channel 1 is inactive (OC1REF=‘0) as long as
TIMx_CNT>TIMx_CCR1 else active (OC1REF=1).
111: PWM mode 2 - In upcounting, channel 1 is inactive as long as TIMx_CNT<TIMx_CCR1
else active. In downcounting, channel 1 is active as long as TIMx_CNT>TIMx_CCR1 else
inactive.
Note: In PWM mode 1 or 2, the OCREF level changes only when the result of the
comparison changes or when the output compare mode switches from “frozen” mode
to “PWM” mode.
Bit 3 OC1PE: Output compare 1 preload enable
0: Preload register on TIMx_CCR1 disabled. TIMx_CCR1 can be written at anytime, the
new value is taken in account immediately.
1: Preload register on TIMx_CCR1 enabled. Read/Write operations access the preload
register. TIMx_CCR1 preload value is loaded in the active register at each update event.
Note: 1: These bits can not be modified as long as LOCK level 3 has been programmed
(LOCK bits in TIMx_BDTR register) and CC1S=00 (the channel is configured in
output).
2: The PWM mode can be used without validating the preload register only in onepulse mode (OPM bit set in TIMx_CR1 register). Else the behavior is not guaranteed.
Bit 2 OC1FE: Output compare 1 fast enable
This bit is used to accelerate the effect of an event on the trigger in input on the CC output.
0: CC1 behaves normally depending on counter and CCR1 values even when the trigger is
ON. The minimum delay to activate CC1 output when an edge occurs on the trigger input is
5 clock cycles.
1: An active edge on the trigger input acts like a compare match on CC1 output. Then, OC
is set to the compare level independently from the result of the comparison. Delay to sample
the trigger input and to activate CC1 output is reduced to 3 clock cycles. OCFE acts only if
the channel is configured in PWM1 or PWM2 mode.
Bits 1:0 CC1S: Capture/Compare 1 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output.
01: CC1 channel is configured as input, IC1 is mapped on TI1.
10: CC1 channel is configured as input, IC1 is mapped on TI2.
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = 0 in TIMx_CCER).
Doc ID16188 Rev 5
329/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Input capture mode
Bits 15:12 IC2F: Input capture 2 filter
Bits 11:10 IC2PSC[1:0]: Input capture 2 prescaler
Bits 9:8 CC2S: Capture/compare 2 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output.
01: CC2 channel is configured as input, IC2 is mapped on TI2.
10: CC2 channel is configured as input, IC2 is mapped on TI1.
11: CC2 channel is configured as input, IC2 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC2S bits are writable only when the channel is OFF (CC2E = 0 in TIMx_CCER).
Bits 7:4 IC1F: Input capture 1 filter
This bit-field defines the frequency used to sample TI1 input and the length of the digital filter
applied to TI1. The digital filter is made of an event counter in which N consecutive events
are needed to validate a transition on the output:
0000: No filter, sampling is done at fDTS
0001: fSAMPLING=fCK_INT, N=2
0010: fSAMPLING=fCK_INT, N=4
0011: fSAMPLING=fCK_INT, N=8
0100: fSAMPLING=fDTS/2, N=6
0101: fSAMPLING=fDTS/2, N=8
0110: fSAMPLING=fDTS/4, N=6
0111: fSAMPLING=fDTS/4, N=8
1000: fSAMPLING=fDTS/8, N=6
1001: fSAMPLING=fDTS/8, N=8
1010: fSAMPLING=fDTS/16, N=5
1011: fSAMPLING=fDTS/16, N=6
1100: fSAMPLING=fDTS/16, N=8
1101: fSAMPLING=fDTS/32, N=5
1110: fSAMPLING=fDTS/32, N=6
1111: fSAMPLING=fDTS/32, N=8
Bits 3:2 IC1PSC: Input capture 1 prescaler
This bit-field defines the ratio of the prescaler acting on CC1 input (IC1).
The prescaler is reset as soon as CC1E=0 (TIMx_CCER register).
00: no prescaler, capture is done each time an edge is detected on the capture input
01: capture is done once every 2 events
10: capture is done once every 4 events
11: capture is done once every 8 events
Bits 1:0 CC1S: Capture/Compare 1 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10: CC1 channel is configured as input, IC1 is mapped on TI2
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = 0 in TIMx_CCER).
330/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
13.4.8
TIMx capture/compare mode register 2 (TIMx_CCMR2)
Address offset: 0x1C
Reset value: 0x0000
Refer to the above CCMR1 register description.
15
14
OC4CE
13
12
OC4M[2:0]
IC4F[3:0]
rw
rw
rw
11
10
OC4PE OC4FE
IC4PSC[1:0]
rw
rw
rw
9
8
CC4S[1:0]
rw
7
6
OC3CE
rw
5
4
OC3M[2:0]
IC3F[3:0]
rw
rw
rw
3
2
OC3PE OC3FE
IC3PSC[1:0]
rw
rw
rw
1
0
CC3S[1:0]
rw
rw
Output compare mode
Bit 15 OC4CE: Output compare 4 clear enable
Bits 14:12 OC4M: Output compare 4 mode
Bit 11 OC4PE: Output compare 4 preload enable
Bit 10 OC4FE: Output compare 4 fast enable
Bits 9:8 CC4S: Capture/Compare 4 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC4 channel is configured as output
01: CC4 channel is configured as input, IC4 is mapped on TI4
10: CC4 channel is configured as input, IC4 is mapped on TI3
11: CC4 channel is configured as input, IC4 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC4S bits are writable only when the channel is OFF (CC4E = 0 in TIMx_CCER).
Bit 7 OC3CE: Output compare 3 clear enable
Bits 6:4 OC3M: Output compare 3 mode
Bit 3 OC3PE: Output compare 3 preload enable
Bit 2 OC3FE: Output compare 3 fast enable
Bits 1:0 CC3S: Capture/Compare 3 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC3 channel is configured as output
01: CC3 channel is configured as input, IC3 is mapped on TI3
10: CC3 channel is configured as input, IC3 is mapped on TI4
11: CC3 channel is configured as input, IC3 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC3S bits are writable only when the channel is OFF (CC3E = 0 in TIMx_CCER).
Doc ID16188 Rev 5
331/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Input capture mode
Bits 15:12 IC4F: Input capture 4 filter
Bits 11:10 IC4PSC: Input capture 4 prescaler
Bits 9:8 CC4S: Capture/Compare 4 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC4 channel is configured as output
01: CC4 channel is configured as input, IC4 is mapped on TI4
10: CC4 channel is configured as input, IC4 is mapped on TI3
11: CC4 channel is configured as input, IC4 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC4S bits are writable only when the channel is OFF (CC4E = 0 in TIMx_CCER).
Bits 7:4 IC3F: Input capture 3 filter
Bits 3:2 IC3PSC: Input capture 3 prescaler
Bits 1:0 CC3S: Capture/Compare 3 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC3 channel is configured as output
01: CC3 channel is configured as input, IC3 is mapped on TI3
10: CC3 channel is configured as input, IC3 is mapped on TI4
11: CC3 channel is configured as input, IC3 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC3S bits are writable only when the channel is OFF (CC3E = 0 in TIMx_CCER).
13.4.9
TIMx capture/compare enable register (TIMx_CCER)
Address offset: 0x20
Reset value: 0x0000
15
14
Reserved
13
12
CC4P
CC4E
rw
rw
11
10
Reserved
9
8
CC3P
CC3E
rw
rw
7
Reserved
Bits 15:14 Reserved, must be kept at reset value.
Bit 13 CC4P: Capture/Compare 4 output polarity
refer to CC1P description
Bit 12 CC4E: Capture/Compare 4 output enable
refer to CC1E description
Bits 11:10 Reserved, must be kept at reset value.
Bit 9 CC3P: Capture/Compare 3 output polarity
refer to CC1P description
Bit 8 CC3E: Capture/Compare 3 output enable
refer to CC1E description
Bits 7:6 Reserved, must be kept at reset value.
Bit 5 CC2P: Capture/Compare 2 output polarity
refer to CC1P description
332/713
6
Doc ID16188 Rev 5
5
4
CC2P
CC2E
rw
rw
3
2
Reserved
1
0
CC1P
CC1E
rw
rw
RM0041
General-purpose timers (TIM2 to TIM5)
Bit 4 CC2E: Capture/Compare 2 output enable
refer to CC1E description
Bits 3:2 Reserved, must be kept at reset value.
Bit 1 CC1P: Capture/Compare 1 output polarity
CC1 channel configured as output:
0: OC1 active high.
1: OC1 active low.
CC1 channel configured as input:
This bit selects whether IC1 or IC1 is used for trigger or capture operations.
0: non-inverted: capture is done on a rising edge of IC1. When used as external trigger, IC1
is non-inverted.
1: inverted: capture is done on a falling edge of IC1. When used as external trigger, IC1 is
inverted.
Bit 0 CC1E: Capture/Compare 1 output enable
CC1 channel configured as output:
0: Off - OC1 is not active.
1: On - OC1 signal is output on the corresponding output pin.
CC1 channel configured as input:
This bit determines if a capture of the counter value can actually be done into the input
capture/compare register 1 (TIMx_CCR1) or not.
0: Capture disabled.
1: Capture enabled.
Table 72. Output control bit for standard OCx channels
CCxE bit
OCx output state
0
Output Disabled (OCx=0, OCx_EN=0)
1
OCx=OCxREF + Polarity, OCx_EN=1
Note:
The state of the external IO pins connected to the standard OCx channels depends on the
OCx channel state and the GPIO and AFIO registers.
13.4.10
TIMx counter (TIMx_CNT)
Address offset: 0x24
Reset value: 0x0000 0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CNT[15:0]
rw
Bits 15:0 CNT[15:0]: Counter value
13.4.11
TIMx prescaler (TIMx_PSC)
Address offset: 0x28
Doc ID16188 Rev 5
333/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
PSC[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 PSC[15:0]: Prescaler value
The counter clock frequency CK_CNT is equal to fCK_PSC / (PSC[15:0] + 1).
PSC contains the value to be loaded in the active prescaler register at each update event
(including when the counter is cleared through UG bit of TIMx_EGR register or through
trigger controller when configured in “reset mode”).
13.4.12
TIMx auto-reload register (TIMx_ARR)
Address offset: 0x2C
Reset value: 0x 0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
ARR[15:0]
Bits 15:0
13.4.13
rw
ARR[15:0]: Low Auto-reload value
ARR is the value to be loaded in the actual auto-reload register.
Refer to the Section 13.3.1: Time-base unit for more details about ARR update and
behavior.
The counter is blocked while the auto-reload value is null.
TIMx capture/compare register 1 (TIMx_CCR1)
Address offset: 0x34
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR1[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR1[15:0]: Capture/Compare 1 value
If channel CC1 is configured as output:
CCR1 is the value to be loaded in the actual capture/compare 1 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR1 register
(bit OC1PE). Else the preload value is copied in the active capture/compare 1 register when
an update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signaled on OC1 output.
If channel CC1is configured as input:
CCR1 is the counter value transferred by the last input capture 1 event (IC1).
13.4.14
TIMx capture/compare register 2 (TIMx_CCR2)
Address offset: 0x38
334/713
Doc ID16188 Rev 5
RM0041
15
General-purpose timers (TIM2 to TIM5)
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR2[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR2[15:0]: Capture/Compare 2 value
If channel CC2 is configured as output:
CCR2 is the value to be loaded in the actual capture/compare 2 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR2 register
(bit OC2PE). Else the preload value is copied in the active capture/compare 2 register when
an update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signalled on OC2 output.
If channel CC2 is configured as input:
CCR2 is the counter value transferred by the last input capture 2 event (IC2).
13.4.15
TIMx capture/compare register 3 (TIMx_CCR3)
Address offset: 0x3C
Reset value: 0x0000
15
14
13
12
11
10
9
rw
rw
rw
rw
rw
rw
rw
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR3[15:0]
rw
rw
Bits 15:0 CCR3[15:0]: Capture/Compare value
If channel CC3 is configured as output:
CCR3 is the value to be loaded in the actual capture/compare 3 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR3 register
(bit OC3PE). Else the preload value is copied in the active capture/compare 3 register when
an update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signaled on OC3 output.
If channel CC3 is configured as input:
CCR3 is the counter value transferred by the last input capture 3 event (IC3).
13.4.16
TIMx capture/compare register 4 (TIMx_CCR4)
Address offset: 0x40
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR4[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Doc ID16188 Rev 5
335/713
339
General-purpose timers (TIM2 to TIM5)
RM0041
Bits 15:0 CCR4[15:0]: Capture/Compare value
1.
if CC4 channel is configured as output (CC4S bits):
CCR4 is the value to be loaded in the actual capture/compare 4 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR4
register (bit OC4PE). Else the preload value is copied in the active capture/compare 4
register when an update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signalled on OC4 output.
2.
if CC4 channel is configured as input (CC4S bits in TIMx_CCMR4 register):
CCR4 is the counter value transferred by the last input capture 4 event (IC4).
13.4.17
TIMx DMA control register (TIMx_DCR)
Address offset: 0x48
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
DBL[4:0]
Reserved
rw
rw
rw
rw
6
5
3
2
1
0
rw
rw
DBA[4:0]
Reserved
rw
4
rw
rw
rw
Bits 15:13 Reserved, must be kept at reset value.
Bits 12:8 DBL[4:0]: DMA burst length
This 5-bit vector defines the number of DMA transfers (the timer recognizes a burst transfer
when a read or a write access is done to the TIMx_DMAR address).
00000: 1 transfer,
00001: 2 transfers,
00010: 3 transfers,
...
10001: 18 transfers.
Bits 7:5 Reserved, must be kept at reset value.
Bits 4:0 DBA[4:0]: DMA base address
This 5-bit vector defines the base-address for DMA transfers (when read/write access are
done through the TIMx_DMAR address). DBA is defined as an offset starting from the
address of the TIMx_CR1 register.
Example:
00000: TIMx_CR1,
00001: TIMx_CR2,
00010: TIMx_SMCR,
...
Example: Let us consider the following transfer: DBL = 7 transfers & DBA = TIMx_CR1. In this
case the transfer is done to/from 7 registers starting from the TIMx_CR1 address.
13.4.18
TIMx DMA address for full transfer (TIMx_DMAR)
Address offset: 0x4C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
DMAB[15:0]
rw
336/713
rw
rw
rw
rw
rw
rw
rw
rw
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM2 to TIM5)
Bits 15:0 DMAB[15:0]: DMA register for burst accesses
A read or write operation to the DMAR register accesses the register located at the address
(TIMx_CR1 address) + (DBA + DMA index) x 4
where TIMx_CR1 address is the address of the control register 1, DBA is the DMA base
address configured in TIMx_DCR register, DMA index is automatically controlled by the
DMA transfer, and ranges from 0 to DBL (DBL configured in TIMx_DCR).
Example of how to use the DMA burst feature
In this example the timer DMA burst feature is used to update the contents of the CCRx
registers (x = 2, 3, 4) with the DMA transferring half words into the CCRx registers.
This is done in the following steps:
1.
Note:
Configure the corresponding DMA channel as follows:
–
DMA channel peripheral address is the DMAR register address
–
DMA channel memory address is the address of the buffer in the RAM containing
the data to be transferred by DMA into CCRx registers.
–
Number of data to transfer = 3 (See note below).
–
Circular mode disabled.
2.
Configure the DCR register by configuring the DBA and DBL bit fields as follows:
DBL = 3 transfers, DBA = 0xE.
3.
Enable the TIMx update DMA request (set the UDE bit in the DIER register).
4.
Enable TIMx
5.
Enable the DMA channel
This example is for the case where every CCRx register to be updated once. If every CCRx
register is to be updated twice for example, the number of data to transfer should be 6. Let's
take the example of a buffer in the RAM containing data1, data2, data3, data4, data5 and
data6. The data is transferred to the CCRx registers as follows: on the first update DMA
request, data1 is transferred to CCR2, data2 is transferred to CCR3, data3 is transferred to
CCR4 and on the second update DMA request, data4 is transferred to CCR2, data5 is
transferred to CCR3 and data6 is transferred to CCR4.
Doc ID16188 Rev 5
337/713
339
General-purpose timers (TIM2 to TIM5)
13.4.19
RM0041
TIMx register map
TIMx registers are mapped as described in the table below:
Reserved
338/713
Doc ID16188 Rev 5
0
0
0
0
0
0
0
CC4S
[1:0]
0
0
0
0
0
0
IC4
PSC
[1:0]
CC4S
[1:0]
0
0
0
0
0
0
0
0
CEN
UIE
UIF
0
UG
0
0
0
0
0
CC1S
[1:0]
0
0
0
0
0
0
0
0
0
IC3F[3:0]
0
URS
0
OC3M
[2:0]
0
Reserved
CC1IE
0
IC1F[3:0]
0
UDIS
DIR
CC2IE
OC2FE
OC1CE
OC2PE
0
OC3CE
0
CC2S
[1:0]
0
OC1M
[2:0]
0
IC2
PSC
[1:0]
0
0
0
0
0
0
0
IC1
PSC
[1:0]
CC1S
[1:0]
0
0
0
CC3S
[1:0]
0
0
0
0
0
IC3
PSC
[1:0]
CC3S
[1:0]
0
0
0
CC1E
0
Reset value
0
0
Reserved
TIMx_CCER
0
0
CC3E
0x20
OC4M
[2:0]
IC4F[3:0]
Reserved
Reset value
0
0
CC3P
TIMx_CCMR2
Input Capture
mode
0
0
0
OC4FE
Reset value
0
0
Reserved
0x1C
0
Reserved
0
CC2S
[1:0]
OC4PE
TIMx_CCMR2
Output
Compare
mode
0
IC2F[3:0]
Reserved
Reset value
0
O24CE
TIMx_CCMR1
Input Capture
mode
0
CC4E
Reset value
OC2M
[2:0]
CC4P
Reserved
Reserved
0x18
0
OC2CE
Reset value
TIMx_CCMR1
Output
Compare
mode
0
CC1IF
TG
0
Reserved
0
CC2IF
0
0
CC1G
CC1OF
0
0
CC2G
CC2OF
0
0
OC1FE
UDE
CC3OF
0
0
0
OC3FE
CC1DE
0
0
CC1P
CC2DE
0
TS[2:0]
0
0
Reserved
CC3DE
0
Reserved
CC4DE
0
Reserved
TIMx_EGR
OPM
Reserved
TIE
0
Reserved
0
CC3IE
0
CC4IE
0
CC3IF
0
CC3G
0
SMS[2:0]
OC1PE
0
0
Reserved
0
0
0
CC4IF
0
0
0
Reserved
0
Reserved
0
CC4G
0
Reset value
0x14
MSM
0
ETF[3:0]
COMDE
TIMx_SR
0
0
Reset value
0x10
0
ETPS
[1:0]
CC4OF
TIMx_DIER
0
ETP
0x0C
0
ECE
Reset value
0
MMS
[2:0]
0
Reserved
0
TDE
TIMx_SMCR
0
CCDS
Reserved
Reset value
0x08
0
Reserved
TIMx_CR2
0
CC2E
0x04
0
CMS
[1:0]
TI1S
Reset value
CKD
[1:0]
OC3PE
Reserved
CC2P
TIMx_CR1
ARPE
0x00
Register
TIF
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 73. TIMx register map and reset values
0
RM0041
General-purpose timers (TIM2 to TIM5)
0x24
Register
TIMx_CNT
CNT[15:0]
Reserved
Reset value
0x28
TIMx_PSC
0
TIMx_ARR
0
0
TIMx_CCR1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CCR1[15:0]
TIMx_CCR2
0
TIMx_CCR3
TIMx_CCR4
0
0
0
0
0
0
0
0
0
CCR2[15:0]
Reserved
0
0
0
0
0
0
0
0
0
0
CCR3[15:0]
Reserved
0
0
0
0
0
0
0
0
0
0
CCR4[15:0]
Reserved
Reset value
0
0
0
0
0
0
0
0
0
0
Reserved
0x44
TIMx_DCR
DBL[4:0]
Reserved
Reset value
0x4C
0
Reserved
Reset value
0x48
0
Reserved
Reset value
0x40
0
ARR[15:0]
Reset value
0x3C
0
Reserved
0x30
0x38
0
PSC[15:0]
Reset value
0x34
0
Reserved
Reset value
0x2C
0
TIMx_DMAR
0
0
0
0
0
DBA[4:0]
0
0
0
0
0
0
0
0
0
0
DMAB[15:0]
Reserved
Reset value
Reserved
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 73. TIMx register map and reset values (continued)
0
0
0
0
0
0
0
0
0
0
0
Refer to Section: Memory map for the register boundary addresses.
Doc ID16188 Rev 5
339/713
339
General-purpose timers (TIM12/13/14)
14
RM0041
General-purpose timers (TIM12/13/14)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 Kbytes and 1 Mbyte.
This section applies to high density value line devices only.
14.1
TIM12/13/14 introduction
The TIM12/13/14 general-purpose timers consist of a 16-bit auto-reload counter driven by a
programmable prescaler.
They may be used for a variety of purposes, including measuring the pulse lengths of input
signals (input capture) or generating output waveforms (output compare, PWM).
Pulse lengths and waveform periods can be modulated from a few microseconds to several
milliseconds using the timer prescaler and the RCC clock controller prescalers.
The TIM12/13/14 timers are completely independent, and do not share any resources. They
can be synchronized together as described in Section 14.3.12.
14.2
TIM12/13/14 main features
14.2.1
TIM12 main features
The features of the general-purpose timer include:
340/713
•
16-bit auto-reload upcounter
•
16-bit programmable prescaler used to divide the counter clock frequency by any factor
between 1 and 65536 (can be changed “on the fly”)
•
Up to 2 independent channels for:
–
Input capture
–
Output compare
–
PWM generation (edge-aligned mode)
–
One-pulse mode output
•
Synchronization circuit to control the timer with external signals and to interconnect
several timers together
•
Interrupt generation on the following events:
–
Update: counter overflow, counter initialization (by software or internal trigger)
–
Trigger event (counter start, stop, initialization or count by internal trigger)
–
Input capture
–
Output compare
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Figure 134. General-purpose timer block diagram (TIM12)
Internal clock (CK_INT)
ITR0
ITR1
TGI
ITR
ITR2
TRC
Trigger
controller
TRGI
ITR3
TI1F_ED
Slave
mode
controller
Reset, Enable, Count
TI1FP1
TI2FP2
U
Auto-reload register
Stop, Clear
CK_PSC
PSC
CK_CNT
Prescaler
+/-
Input filter &
Edge detector
TIMx_CH1
TI1FP1
TI1FP2
IC1
Prescaler
CC1I
TIMx_CH2
Input filter &
Edge detector
Capture/Compare 1 register
OC1REF
output
OC1
control
TRC
TI2
IC1PS U
U
CNT
COUNTER
CC1I
TI1
UI
TI2FP1
TI2FP2
CC2I
IC2
CC2I
IC2PS U
Prescaler
TIMx_CH1
Capture/Compare 2 register
OC2REF
output
OC2
TIMx_CH2
control
TRC
Notes:
Reg
Preload registers transferred
to active registers on U event
according to control bit
event
interrupt
ai17190
14.2.2
TIM13/TIM14 main features
The features of general-purpose timers TIM13/TIM14 include:
•
16-bit auto-reload upcounter
•
16-bit programmable prescaler used to divide the counter clock frequency by any factor
between 1 and 65536 (can be changed “on the fly”)
•
independent channel for:
•
–
Input capture
–
Output compare
–
PWM generation (edge-aligned mode)
–
One-pulse mode output
Interrupt generation on the following events:
–
Update: counter overflow, counter initialization (by software)
–
Input capture
–
Output compare
Doc ID16188 Rev 5
341/713
457
General-purpose timers (TIM12/13/14)
RM0041
Figure 135. General-purpose timer block diagram (TIM13/14)
)NTERNALCLOCK#+?).4
4RIGGER
#ONTROLLER
5
%NABLE
COUNTER
!UTORELOADREGISTER
3TOP#LEAR
#+?03#
03#
PRESCALER
#+?#.4
5)
5
#.4
COUNTER
##)
4)
4)-X?#(
)NPUTFILTER
EDGEDETECTOR
4)&0 )#
##)
5
0RESCALER
)#03
#APTURE#OMPAREREGISTER
/#2%&
OUTPUT /#
CONTROL
4)-X?#(
.OTES
2EG
0RELOADREGISTERSTRANSFERRED
TOACTIVEREGISTERSON5EVENT
ACCORDINGTOCONTROLBIT
EVENT
INTERRUPT$-!OUTPUT
AIC
342/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
14.3
TIM12/13/14 functional description
14.3.1
Time-base unit
The main block of the timer is a 16-bit counter with its related auto-reload register. The
counters counts up.
The counter clock can be divided by a prescaler.
The counter, the auto-reload register and the prescaler register can be written or read by
software. This is true even when the counter is running.
The time-base unit includes:
•
Counter register (TIMx_CNT)
•
Prescaler register (TIMx_PSC)
•
Auto-reload register (TIMx_ARR)
The auto-reload register is preloaded. Writing to or reading from the auto-reload register
accesses the preload register. The content of the preload register are transferred into the
shadow register permanently or at each update event (UEV), depending on the auto-reload
preload enable bit (ARPE) in TIMx_CR1 register. The update event is sent when the counter
reaches the overflow and if the UDIS bit equals 0 in the TIMx_CR1 register. It can also be
generated by software. The generation of the update event is described in details for each
configuration.
The counter is clocked by the prescaler output CK_CNT, which is enabled only when the
counter enable bit (CEN) in TIMx_CR1 register is set (refer also to the slave mode controller
description to get more details on counter enabling).
Note that the counter starts counting 1 clock cycle after setting the CEN bit in the TIMx_CR1
register.
Prescaler description
The prescaler can divide the counter clock frequency by any factor between 1 and 65536. It
is based on a 16-bit counter controlled through a 16-bit register (in the TIMx_PSC register).
It can be changed on the fly as this control register is buffered. The new prescaler ratio is
taken into account at the next update event.
Figure 136 and Figure 137 give some examples of the counter behavior when the prescaler
ratio is changed on the fly.
Doc ID16188 Rev 5
343/713
457
General-purpose timers (TIM12/13/14)
RM0041
Figure 136. Counter timing diagram with prescaler division change from 1 to 2
&.B36&
&(1
7LPHUFORFN
&.B&17
&RXQWHUUHJLVWHU
)
)
)
)$ )% )&
8SGDWHHYHQW8(9
3UHVFDOHUFRQWUROUHJLVWHU
:ULWHDQHZYDOXHLQ7,0[B36&
3UHVFDOHUEXIIHU
3UHVFDOHUFRXQWHU
069
Figure 137. Counter timing diagram with prescaler division change from 1 to 4
&.B36&
&(1
7LPHUFORFN
&.B&17
&RXQWHUUHJLVWHU
)
)
)
)$ )% )&
8SGDWHHYHQW8(9
3UHVFDOHUFRQWUROUHJLVWHU
:ULWHDQHZYDOXHLQ7,0[B36&
3UHVFDOHUEXIIHU
3UHVFDOHUFRXQWHU
069
344/713
Doc ID16188 Rev 5
RM0041
14.3.2
General-purpose timers (TIM12/13/14)
Counter modes
Upcounting mode
In upcounting mode, the counter counts from 0 to the auto-reload value (content of the
TIMx_ARR register), then restarts from 0 and generates a counter overflow event.
Setting the UG bit in the TIMx_EGR register (by software or by using the slave mode
controller on TIM12) also generates an update event.
The UEV event can be disabled by software by setting the UDIS bit in the TIMx_CR1
register. This is to avoid updating the shadow registers while writing new values in the
preload registers. Then no update event occurs until the UDIS bit has been written to 0.
However, the counter restarts from 0, as well as the counter of the prescaler (but the
prescale rate does not change). In addition, if the URS bit (update request selection) in
TIMx_CR1 register is set, setting the UG bit generates an update event UEV but without
setting the UIF flag (thus no interrupt is sent). This is to avoid generating both update and
capture interrupts when clearing the counter on the capture event.
When an update event occurs, all the registers are updated and the update flag (UIF bit in
TIMx_SR register) is set (depending on the URS bit):
•
The auto-reload shadow register is updated with the preload value (TIMx_ARR),
•
The buffer of the prescaler is reloaded with the preload value (content of the TIMx_PSC
register).
The following figures show some examples of the counter behavior for different clock
frequencies when TIMx_ARR=0x36.
Figure 138. Counter timing diagram, internal clock divided by 1
<ͺW^
EdͺE
dŝŵĞƌĐůŽĐŬс<ͺEd
ŽƵŶƚĞƌƌĞŐŝƐƚĞƌ
ϯϭ
ϯϮ
ϯϯ
ϯϰ
ϯϱ
ϯϲ
ϬϬ
Ϭϭ
ϬϮ
Ϭϯ
Ϭϰ
Ϭϱ
Ϭϲ
Ϭϳ
ŽƵŶƚĞƌŽǀĞƌĨůŽǁ
hƉĚĂƚĞĞǀĞŶƚ;hsͿ
hƉĚĂƚĞŝŶƚĞƌƌƵƉƚĨůĂŐ;h/&Ϳ
069
Doc ID16188 Rev 5
345/713
457
General-purpose timers (TIM12/13/14)
RM0041
Figure 139. Counter timing diagram, internal clock divided by 2
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 140. Counter timing diagram, internal clock divided by 4
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 141. Counter timing diagram, internal clock divided by N
&.B36&
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
346/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Figure 142. Counter timing diagram, update event when ARPE=0 (TIMx_ARR not
preloaded)
<ͺW^
E
dŝŵĞƌĐůŽĐŬс<ͺEd
ŽƵŶƚĞƌƌĞŐŝƐƚĞƌ
ϯϭ
ϯϯ
ϯϮ
ϯϰ
ϯϱ
ϯϲ
ϬϬ
Ϭϭ
ϬϮ
Ϭϯ
Ϭϰ
Ϭϱ
Ϭϲ
Ϭϳ
ŽƵŶƚĞƌŽǀĞƌĨůŽǁ
hƉĚĂƚĞĞǀĞŶƚ;hsͿ
hƉĚĂƚĞŝŶƚĞƌƌƵƉƚĨůĂŐ;h/&Ϳ
ƵƚŽͲƌĞůŽĂĚƉƌĞůŽĂĚƌĞŐŝƐƚĞƌ
&&
ϯϲ
tƌŝƚĞĂŶĞǁǀĂůƵĞŝŶd/DdžͺZZ
069
Figure 143. Counter timing diagram, update event when ARPE=1 (TIMx_ARR
preloaded)
&.B36&
&(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
)
)
)
) )
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ
8,)
$XWRUHORDGSUHORDG
UHJLVWHU
)
$XWRUHORDGVKDGRZ
UHJLVWHU
)
:ULWHDQHZYDOXHLQ7,0[B$55
Doc ID16188 Rev 5
069
347/713
457
General-purpose timers (TIM12/13/14)
14.3.3
RM0041
Clock selection
The counter clock can be provided by the following clock sources:
•
Internal clock (CK_INT)
•
External clock mode1 (for TIM12): external input pin (TIx)
•
Internal trigger inputs (ITRx) (for TIM12): connecting the trigger output from another
timer. Refer to Section : Using one timer as prescaler for another timer for more details.
Internal clock source (CK_INT)
The internal clock source is the default clock source for TIM13/TIM14.
For TIM9, the internal clock source is selected when the slave mode controller is disabled
(SMS=’000’). The CEN bit in the TIMx_CR1 register and the UG bit in the TIMx_EGR
register are then used as control bits and can be changed only by software (except for UG
which remains cleared). As soon as the CEN bit is programmed to 1, the prescaler is
clocked by the internal clock CK_INT.
Figure 144 shows the behavior of the control circuit and the upcounter in normal mode,
without prescaler.
Figure 144. Control circuit in normal mode, internal clock divided by 1
,QWHUQDOFORFN
&(1 &17B(1
8*
&17B,1,7
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
069
External clock source mode 1(TIM12)
This mode is selected when SMS=’111’ in the TIMx_SMCR register. The counter can count
at each rising or falling edge on a selected input.
348/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Figure 145. TI2 external clock connection example
7,0[B60&5
76>@
RU 7,)
7,)
,75[
7,B('
7,
(GJH
GHWHFWRU
)LOWHU
7,)B5LVLQJ
7,)B)DOOLQJ
7,)3
7,)3
RU
RU
[[
75*,
&.B,17
,&)>@
&&3
7,0[B&&05
7,0[B&&(5
&.B36&
([WHUQDOFORFN
PRGH
LQWHUQDOFORFN
,QWHUQDOFORFN
PRGH
606>@
7,0[B60&5
069
For example, to configure the upcounter to count in response to a rising edge on the TI2
input, use the following procedure:
Note:
1.
Configure channel 2 to detect rising edges on the TI2 input by writing CC2S = ‘01’ in
the TIMx_CCMR1 register.
2.
Configure the input filter duration by writing the IC2F[3:0] bits in the TIMx_CCMR1
register (if no filter is needed, keep IC2F=’0000’).
3.
Select the rising edge polarity by writing CC2P=’0’ and CC2NP=’0’ in the TIMx_CCER
register.
4.
Configure the timer in external clock mode 1 by writing SMS=’111’ in the TIMx_SMCR
register.
5.
Select TI2 as the trigger input source by writing TS=’110’ in the TIMx_SMCR register.
6.
Enable the counter by writing CEN=’1’ in the TIMx_CR1 register.
The capture prescaler is not used for triggering, so no need to configure it.
When a rising edge occurs on TI2, the counter counts once and the TIF flag is set.
The delay between the rising edge on TI2 and the actual clock of the counter is due to the
resynchronization circuit on TI2 input.
Figure 146. Control circuit in external clock mode 1
7,
&17B(1
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
7,)
:ULWH7,) Doc ID16188 Rev 5
069
349/713
457
General-purpose timers (TIM12/13/14)
14.3.4
RM0041
Capture/compare channels
Each Capture/Compare channel is built around a capture/compare register (including a
shadow register), a input stage for capture (with digital filter, multiplexing and prescaler) and
an output stage (with comparator and output control).
Figure 147 to Figure 149 give an overview of a capture/compare channel.
The input stage samples the corresponding TIx input to generate a filtered signal TIxF.
Then, an edge detector with polarity selection generates a signal (TIxFPx) which can be
used as trigger input by the slave mode controller or as the capture command. It is
prescaled before the capture register (ICxPS).
Figure 147. Capture/compare channel (example: channel 1 input stage)
7,)B('
7RWKHVODYHPRGHFRQWUROOHU
7,
I'76
7,)B5LVLQJ
)LOWHU
7,)
GRZQFRXQWHU
(GJH
GHWHFWRU
7,)B)DOOLQJ
7,)3
7,)3
,&)>@
7,0[B&&05
&&3&&13
7,0[B&&(5
7,)B5LVLQJ
IURPFKDQQHO
7,)B)DOOLQJ
IURPFKDQQHO
75&
IURPVODYHPRGH
FRQWUROOHU
,&
,&36
'LYLGHU
&&6>@ ,&36>@
&&(
7,0[B&&05
7,0[B&&(5
069
The output stage generates an intermediate waveform which is then used for reference:
OCxRef (active high). The polarity acts at the end of the chain.
350/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Figure 148. Capture/compare channel 1 main circuit
$3%%XV
5HDG&&5+ 6
5HDG&&5/
KLJK
UHDGBLQBSURJUHVV
&&6>@
ZULWHBLQBSURJUHVV
,QSXW
PRGH
6 ZULWH&&5+
&DSWXUHFRPSDUHSUHORDGUHJLVWHU
5
5
2XWSXW
PRGH
FRPSDUHBWUDQVIHU
FDSWXUHBWUDQVIHU
&&6>@
ORZ
LIELW
0&8SHULSKHUDOLQWHUIDFH
&&(
&17!&&5
&RXQWHU
&&6>@
8(9
&RPSDUDWRU
&DSWXUH
&&6>@
2&3(
&DSWXUHFRPSDUHVKDGRZUHJLVWHU
,&36
ZULWH&&5/
IURPWLPH
EDVHXQLW
2&3(
7,0B&&05
&17 &&5
&&*
7,0B(*5
069
Figure 149. Output stage of capture/compare channel (channel 1)
7RWKHPDVWHU
PRGHFRQWUROOHU
&17!&&5
2XWSXW
PRGH
&17 &&5
FRQWUROOHU
2&B5()
2XWSXW
HQDEOH
FLUFXLW
2&
&&3
7,0[B&&(5
2&0>@
&&( 7,0[B&&(5
7,0[B&&05
DL
The capture/compare block is made of one preload register and one shadow register. Write
and read always access the preload register.
In capture mode, captures are actually done in the shadow register, which is copied into the
preload register.
In compare mode, the content of the preload register is copied into the shadow register
which is compared to the counter.
14.3.5
Input capture mode
In Input capture mode, the Capture/Compare Registers (TIMx_CCRx) are used to latch the
value of the counter after a transition detected by the corresponding ICx signal. When a
Doc ID16188 Rev 5
351/713
457
General-purpose timers (TIM12/13/14)
RM0041
capture occurs, the corresponding CCXIF flag (TIMx_SR register) is set and an interrupt or
a DMA request can be sent if they are enabled. If a capture occurs while the CCxIF flag was
already high, then the over-capture flag CCxOF (TIMx_SR register) is set. CCxIF can be
cleared by software by writing it to ‘0’ or by reading the captured data stored in the
TIMx_CCRx register. CCxOF is cleared when the user writes it to ‘0’.
The following example shows how to capture the counter value in TIMx_CCR1 when TI1
input rises. To do this, use the following procedure:
1.
Select the active input: TIMx_CCR1 must be linked to the TI1 input, so write the CC1S
bits to ‘01’ in the TIMx_CCMR1 register. As soon as CC1S becomes different from ‘00’,
the channel is configured in input mode and the TIMx_CCR1 register becomes readonly.
2.
Program the needed input filter duration with respect to the signal connected to the
timer (by programming the ICxF bits in the TIMx_CCMRx register if the input is one of
the TIx inputs). Let’s imagine that, when toggling, the input signal is not stable during at
must 5 internal clock cycles. We must program a filter duration longer than these 5
clock cycles. We can validate a transition on TI1 when 8 consecutive samples with the
new level have been detected (sampled at fDTS frequency). Then write IC1F bits to
‘0011’ in the TIMx_CCMR1 register.
3.
Select the edge of the active transition on the TI1 channel by programming CC1P and
CC1NP bits to ‘00’ in the TIMx_CCER register (rising edge in this case).
4.
Program the input prescaler. In our example, we wish the capture to be performed at
each valid transition, so the prescaler is disabled (write IC1PS bits to ‘00’ in the
TIMx_CCMR1 register).
5.
Enable capture from the counter into the capture register by setting the CC1E bit in the
TIMx_CCER register.
6.
If needed, enable the related interrupt request by setting the CC1IE bit in the
TIMx_DIER register.
When an input capture occurs:
•
The TIMx_CCR1 register gets the value of the counter on the active transition.
•
CC1IF flag is set (interrupt flag). CC1OF is also set if at least two consecutive captures
occurred whereas the flag was not cleared.
•
An interrupt is generated depending on the CC1IE bit.
In order to handle the overcapture, it is recommended to read the data before the
overcapture flag. This is to avoid missing an overcapture which could happen after reading
the flag and before reading the data.
Note:
352/713
IC interrupt requests can be generated by software by setting the corresponding CCxG bit in
the TIMx_EGR register.
Doc ID16188 Rev 5
RM0041
14.3.6
General-purpose timers (TIM12/13/14)
PWM input mode (only for TIM12)
This mode is a particular case of input capture mode. The procedure is the same except:
•
Two ICx signals are mapped on the same TIx input.
•
These 2 ICx signals are active on edges with opposite polarity.
•
One of the two TIxFP signals is selected as trigger input and the slave mode controller
is configured in reset mode.
For example, the user can measure the period (in TIMx_CCR1 register) and the duty cycle
(in TIMx_CCR2 register) of the PWM applied on TI1 using the following procedure
(depending on CK_INT frequency and prescaler value):
1.
Select the active input for TIMx_CCR1: write the CC1S bits to ‘01’ in the TIMx_CCMR1
register (TI1 selected).
2.
Select the active polarity for TI1FP1 (used both for capture in TIMx_CCR1 and counter
clear): program the CC1P and CC1NP bits to ‘00’ (active on rising edge).
3.
Select the active input for TIMx_CCR2: write the CC2S bits to ‘10’ in the TIMx_CCMR1
register (TI1 selected).
4.
Select the active polarity for TI1FP2 (used for capture in TIMx_CCR2): program the
CC2P and CC2NP bits to ‘11’ (active on falling edge).
5.
Select the valid trigger input: write the TS bits to ‘101’ in the TIMx_SMCR register
(TI1FP1 selected).
6.
Configure the slave mode controller in reset mode: write the SMS bits to ‘100’ in the
TIMx_SMCR register.
7.
Enable the captures: write the CC1E and CC2E bits to ‘1’ in the TIMx_CCER register.
Figure 150. PWM input mode timing
TI1
TIMx_CNT
0004
0000
0001
0002
TIMx_CCR1
0004
TIMx_CCR2
0002
IC1 capture
IC2 capture
reset counter
0003
0004
IC2 capture
pulse width
measurement
0000
IC1 capture
period
measurement
ai15413
1. The PWM input mode can be used only with the TIMx_CH1/TIMx_CH2 signals due to the fact that only
TI1FP1 and TI2FP2 are connected to the slave mode controller.
Doc ID16188 Rev 5
353/713
457
General-purpose timers (TIM12/13/14)
14.3.7
RM0041
Forced output mode
In output mode (CCxS bits = ‘00’ in the TIMx_CCMRx register), each output compare signal
(OCxREF and then OCx) can be forced to active or inactive level directly by software,
independently of any comparison between the output compare register and the counter.
To force an output compare signal (OCXREF/OCx) to its active level, the user just needs to
write ‘101’ in the OCxM bits in the corresponding TIMx_CCMRx register. Thus OCXREF is
forced high (OCxREF is always active high) and OCx get opposite value to CCxP polarity
bit.
For example: CCxP=’0’ (OCx active high) => OCx is forced to high level.
The OCxREF signal can be forced low by writing the OCxM bits to ‘100’ in the
TIMx_CCMRx register.
Anyway, the comparison between the TIMx_CCRx shadow register and the counter is still
performed and allows the flag to be set. Interrupt requests can be sent accordingly. This is
described in the output compare mode section below.
14.3.8
Output compare mode
This function is used to control an output waveform or indicating when a period of time has
elapsed.
When a match is found between the capture/compare register and the counter, the output
compare function:
1.
Assigns the corresponding output pin to a programmable value defined by the output
compare mode (OCxM bits in the TIMx_CCMRx register) and the output polarity (CCxP
bit in the TIMx_CCER register). The output pin can keep its level (OCXM=’000’), be set
active (OCxM=’001’), be set inactive (OCxM=’010’) or can toggle (OCxM=’011’) on
match.
2.
Sets a flag in the interrupt status register (CCxIF bit in the TIMx_SR register).
3.
Generates an interrupt if the corresponding interrupt mask is set (CCXIE bit in the
TIMx_DIER register).
The TIMx_CCRx registers can be programmed with or without preload registers using the
OCxPE bit in the TIMx_CCMRx register.
In output compare mode, the update event UEV has no effect on OCxREF and OCx output.
The timing resolution is one count of the counter. Output compare mode can also be used to
output a single pulse (in One-pulse mode).
Procedure:
1.
Select the counter clock (internal, external, prescaler).
2.
Write the desired data in the TIMx_ARR and TIMx_CCRx registers.
3.
Set the CCxIE bit if an interrupt request is to be generated.
4.
5.
354/713
Select the output mode. For example:
–
Write OCxM = ‘011’ to toggle OCx output pin when CNT matches CCRx
–
Write OCxPE = ‘0’ to disable preload register
–
Write CCxP = ‘0’ to select active high polarity
–
Write CCxE = ‘1’ to enable the output
Enable the counter by setting the CEN bit in the TIMx_CR1 register.
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
The TIMx_CCRx register can be updated at any time by software to control the output
waveform, provided that the preload register is not enabled (OCxPE=’0’, else TIMx_CCRx
shadow register is updated only at the next update event UEV). An example is given in
Figure 151.
Figure 151. Output compare mode, toggle on OC1.
:ULWH%KLQWKH&&5UHJLVWHU
7,0B&17
$
7,0B&&5
%
%
%
%
$
2&5() 2&
0DWFKGHWHFWHGRQ&&5
,QWHUUXSWJHQHUDWHGLIHQDEOHG
069
14.3.9
PWM mode
Pulse Width Modulation mode allows the user to generate a signal with a frequency
determined by the value of the TIMx_ARR register and a duty cycle determined by the value
of the TIMx_CCRx register.
The PWM mode can be selected independently on each channel (one PWM per OCx
output) by writing ‘110’ (PWM mode 1) or ‘111’ (PWM mode 2) in the OCxM bits in the
TIMx_CCMRx register. Enable the corresponding preload register by setting the OCxPE bit
in the TIMx_CCMRx register, and eventually the auto-reload preload register by setting the
ARPE bit in the TIMx_CR1 register.
As the preload registers are transferred to the shadow registers only when an update event
occurs, before starting the counter, the user has to initialize all the registers by setting the
UG bit in the TIMx_EGR register.
The OCx polarity is software programmable using the CCxP bit in the TIMx_CCER register.
It can be programmed as active high or active low. The OCx output is enabled by the CCxE
bit in the TIMx_CCER register. Refer to the TIMx_CCERx register description for more
details.
In PWM mode (1 or 2), TIMx_CNT and TIMx_CCRx are always compared to determine
whether TIMx_CNT ≤TIMx_CCRx.
The timer is able to generate PWM in edge-aligned mode only since the counter is
upcounting.
PWM edge-aligned mode
In the following example, we consider PWM mode 1. The reference PWM signal OCxREF is
high as long as TIMx_CNT < TIMx_CCRx else it becomes low. If the compare value in
Doc ID16188 Rev 5
355/713
457
General-purpose timers (TIM12/13/14)
RM0041
TIMx_CCRx is greater than the auto-reload value (in TIMx_ARR) then OCxREF is held at
‘1’. If the compare value is 0 then OCxRef is held at ‘0’. Figure 152 shows some edgealigned PWM waveforms in an example where TIMx_ARR=8.
Figure 152. Edge-aligned PWM waveforms (ARR=8)
&RXQWHUUHJLVWHU
&&5[ 2&;5()
&&[,)
2&;5()
&&5[ &&[,)
2&;5()
µ¶
&&5[!
&&[,)
2&;5()
µ¶
&&5[ &&[,)
069
14.3.10
One-pulse mode
One-pulse mode (OPM) is a particular case of the previous modes. It allows the counter to
be started in response to a stimulus and to generate a pulse with a programmable length
after a programmable delay.
Starting the counter can be controlled through the slave mode controller. Generating the
waveform can be done in output compare mode or PWM mode. Select One-pulse mode by
setting the OPM bit in the TIMx_CR1 register. This makes the counter stop automatically at
the next update event UEV.
A pulse can be correctly generated only if the compare value is different from the counter
initial value. Before starting (when the timer is waiting for the trigger), the configuration must
be as follows:
CNT < CCRx≤ ARR (in particular, 0 < CCRx)
356/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Figure 153. Example of one pulse mode.
7,
2&5()
2&
&RXQWHU
7,0B$55
7,0B&&5
W'(/$<
W38/6(
W
069
For example the user may want to generate a positive pulse on OC1 with a length of tPULSE
and after a delay of tDELAY as soon as a positive edge is detected on the TI2 input pin.
Use TI2FP2 as trigger 1:
1.
Map TI2FP2 to TI2 by writing CC2S=’01’ in the TIMx_CCMR1 register.
2.
TI2FP2 must detect a rising edge, write CC2P=’0’ and CC2NP = ‘0’ in the TIMx_CCER
register.
3.
Configure TI2FP2 as trigger for the slave mode controller (TRGI) by writing TS=’110’ in
the TIMx_SMCR register.
4.
TI2FP2 is used to start the counter by writing SMS to ‘110’ in the TIMx_SMCR register
(trigger mode).
The OPM waveform is defined by writing the compare registers (taking into account the
clock frequency and the counter prescaler).
•
The tDELAY is defined by the value written in the TIMx_CCR1 register.
•
The tPULSE is defined by the difference between the auto-reload value and the compare
value (TIMx_ARR - TIMx_CCR1).
•
Let us say the user wants to build a waveform with a transition from ‘0’ to ‘1’ when a
compare match occurs and a transition from ‘1’ to ‘0’ when the counter reaches the
auto-reload value. To do this enable PWM mode 2 by writing OC1M=’111’ in the
TIMx_CCMR1 register. The user can optionally enable the preload registers by writing
OC1PE=’1’ in the TIMx_CCMR1 register and ARPE in the TIMx_CR1 register. In this
case the user has to write the compare value in the TIMx_CCR1 register, the autoreload value in the TIMx_ARR register, generate an update by setting the UG bit and
wait for external trigger event on TI2. CC1P is written to ‘0’ in this example.
The user only wants one pulse (Single mode), so write '1 in the OPM bit in the TIMx_CR1
register to stop the counter at the next update event (when the counter rolls over from the
auto-reload value back to 0). When OPM bit in the TIMx_CR1 register is set to '0', so the
Repetitive Mode is selected.
Doc ID16188 Rev 5
357/713
457
General-purpose timers (TIM12/13/14)
RM0041
Particular case: OCx fast enable
In One-pulse mode, the edge detection on TIx input set the CEN bit which enables the
counter. Then the comparison between the counter and the compare value makes the
output toggle. But several clock cycles are needed for these operations and it limits the
minimum delay tDELAY min we can get.
If the user wants to output a waveform with the minimum delay, set the OCxFE bit in the
TIMx_CCMRx register. Then OCxRef (and OCx) are forced in response to the stimulus,
without taking in account the comparison. Its new level is the same as if a compare match
had occurred. OCxFE acts only if the channel is configured in PWM1 or PWM2 mode.
14.3.11
TIM12 external trigger synchronization
The TIM12 timer can be synchronized with an external trigger in several modes: Reset
mode, Gated mode and Trigger mode.
Slave mode: Reset mode
The counter and its prescaler can be reinitialized in response to an event on a trigger input.
Moreover, if the URS bit from the TIMx_CR1 register is low, an update event UEV is
generated. Then all the preloaded registers (TIMx_ARR, TIMx_CCRx) are updated.
In the following example, the upcounter is cleared in response to a rising edge on TI1 input:
1.
Configure the channel 1 to detect rising edges on TI1. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC1F=’0000’). The capture
prescaler is not used for triggering, so there’s no need to configure it. The CC1S bits
select the input capture source only, CC1S = ‘01’ in the TIMx_CCMR1 register.
Program CC1P and CC1NP to ‘00’ in TIMx_CCER register to validate the polarity (and
detect rising edges only).
2.
Configure the timer in reset mode by writing SMS=’100’ in TIMx_SMCR register. Select
TI1 as the input source by writing TS=’101’ in TIMx_SMCR register.
3.
Start the counter by writing CEN=’1’ in the TIMx_CR1 register.
The counter starts counting on the internal clock, then behaves normally until TI1 rising
edge. When TI1 rises, the counter is cleared and restarts from 0. In the meantime, the
trigger flag is set (TIF bit in the TIMx_SR register) and an interrupt request can be sent if
enabled (depending on the TIE bit in TIMx_DIER register).
The following figure shows this behavior when the auto-reload register TIMx_ARR=0x36.
The delay between the rising edge on TI1 and the actual reset of the counter is due to the
resynchronization circuit on TI1 input.
358/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Figure 154. Control circuit in reset mode
7,
8*
&RXQWHUFORFN FNBFQW FNBSVF
&RXQWHUUHJLVWHU
7,)
069
Slave mode: Gated mode
The counter can be enabled depending on the level of a selected input.
In the following example, the upcounter counts only when TI1 input is low:
1.
Configure the channel 1 to detect low levels on TI1. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC1F=’0000’). The capture
prescaler is not used for triggering, so there’s no need to configure it. The CC1S bits
select the input capture source only, CC1S=’01’ in TIMx_CCMR1 register. Program
CC1P=’1’ and CC1NP= ‘0’ in TIMx_CCER register to validate the polarity (and detect
low level only).
2.
Configure the timer in gated mode by writing SMS=’101’ in TIMx_SMCR register.
Select TI1 as the input source by writing TS=’101’ in TIMx_SMCR register.
3.
Enable the counter by writing CEN=’1’ in the TIMx_CR1 register (in gated mode, the
counter doesn’t start if CEN=’0’, whatever is the trigger input level).
The counter starts counting on the internal clock as long as TI1 is low and stops as soon as
TI1 becomes high. The TIF flag in the TIMx_SR register is set both when the counter starts
or stops.
The delay between the rising edge on TI1 and the actual stop of the counter is due to the
resynchronization circuit on TI1 input.
Doc ID16188 Rev 5
359/713
457
General-purpose timers (TIM12/13/14)
RM0041
Figure 155. Control circuit in gated mode
7,
FQWBHQ
&RXQWHUFORFN FNBFQW FNBSVF
&RXQWHUUHJLVWHU
7,)
:ULWH7,) 069
Slave mode: Trigger mode
The counter can start in response to an event on a selected input.
In the following example, the upcounter starts in response to a rising edge on TI2 input:
1.
Configure the channel 2 to detect rising edges on TI2. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC2F=’0000’). The capture
prescaler is not used for triggering, so there’s no need to configure it. The CC2S bits
are configured to select the input capture source only, CC2S=’01’ in TIMx_CCMR1
register. Program CC2P=’1’ and CC2NP=’0’ in TIMx_CCER register to validate the
polarity (and detect low level only).
2.
Configure the timer in trigger mode by writing SMS=’110’ in TIMx_SMCR register.
Select TI2 as the input source by writing TS=’110’ in TIMx_SMCR register.
When a rising edge occurs on TI2, the counter starts counting on the internal clock and the
TIF flag is set.
The delay between the rising edge on TI2 and the actual start of the counter is due to the
resynchronization circuit on TI2 input.
Figure 156. Control circuit in trigger mode
7,
FQWBHQ
&RXQWHUFORFN FNBFQW FNBSVF
&RXQWHUUHJLVWHU
7,)
069
360/713
Doc ID16188 Rev 5
RM0041
14.3.12
General-purpose timers (TIM12/13/14)
Timer synchronization (TIM12)
The TIM timers are linked together internally for timer synchronization or chaining. Refer to
Section 13.3.15: Timer synchronization for details.
Note:
The clock of the slave timer must be enabled prior to receive events from the master timer,
and must not be changed on-the-fly while triggers are received from the master timer.
14.3.13
Debug mode
When the microcontroller enters debug mode (Cortex®-M3 core halted), the TIMx counter
either continues to work normally or stops, depending on DBG_TIMx_STOP configuration
bit in DBG module. For more details, refer to Section 25.15.2: Debug support for timers,
watchdog and I2C.
Doc ID16188 Rev 5
361/713
457
General-purpose timers (TIM12/13/14)
14.4
RM0041
TIM12 registers
Refer to Section: List of abbreviations for registers for a list of abbreviations used in register
descriptions.
The peripheral registers have to be written by half-words (16 bits) or words (32 bits). Read
accesses can be done by bytes (8 bits), half-words (16 bits) or words (32 bits).
14.4.1
TIM12 control register 1 (TIMx_CR1)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
Reserved
11
10
9
8
CKD[1:0]
rw
7
ARPE
rw
rw
6
5
Reserved
4
3
2
1
0
OPM
URS
UDIS
CEN
rw
rw
rw
rw
Bits 15:10 Reserved, must be kept at reset value.
Bits 9:8 CKD: Clock division
This bit-field indicates the division ratio between the timer clock (CK_INT) frequency and
sampling clock used by the digital filters (TIx),
00: tDTS = tCK_INT
01: tDTS = 2 × tCK_INT
10: tDTS = 4 × tCK_INT
11: Reserved
Bit 7 ARPE: Auto-reload preload enable
0: TIMx_ARR register is not buffered.
1: TIMx_ARR register is buffered.
Bits 6:4 Reserved, must be kept at reset value.
Bit 3 OPM: One-pulse mode
0: Counter is not stopped on the update event
1: Counter stops counting on the next update event (clearing the CEN bit).
362/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Bit 2 URS: Update request source
This bit is set and cleared by software to select the UEV event sources.
0: Any of the following events generates an update interrupt if enabled:
–
Counter overflow
–
Setting the UG bit
1: Only counter overflow generates an update interrupt if enabled.
Bit 1 UDIS: Update disable
This bit is set and cleared by software to enable/disable update event (UEV) generation.
0: UEV enabled. An UEV is generated by one of the following events:
–
Counter overflow
–
Setting the UG bit
Buffered registers are then loaded with their preload values.
1: UEV disabled. No UEV is generated, shadow registers keep their value (ARR, PSC,
CCRx). The counter and the prescaler are reinitialized if the UG bit is set.
Bit 0 CEN: Counter enable
0: Counter disabled
1: Counter enabled
CEN is cleared automatically in one-pulse mode, when an update event occurs.
Doc ID16188 Rev 5
363/713
457
General-purpose timers (TIM12/13/14)
14.4.2
RM0041
TIM12 control register 2 (TIMx_CR2)
Address offset: 0x04
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
MMS[2:0]
Reserved
rw
rw
rw
3
2
1
0
Reserved
Bits 15:7 Reserved, must be kept at reset value.
Bits 6:4 MMS[2:0]: Master mode selection
These bits are used to select the information to be sent in Master mode to slave timers for
synchronization (TRGO). The combination is as follows:
000: Reset - the UG bit in the TIMx_EGR register is used as the trigger output (TRGO). If
the reset is generated by the trigger input (slave mode controller configured in reset mode)
then the signal on TRGO is delayed compared to the actual reset.
001: Enable - the Counter enable signal, CNT_EN, is used as the trigger output (TRGO). It
is useful to start several timers at the same time or to control a window in which a slave timer
is enabled. The Counter Enable signal is generated by a logic OR between the CEN control
bit and the trigger input when configured in Gated mode.
When the Counter Enable signal is controlled by the trigger input, there is a delay on TRGO,
except if the master/slave mode is selected (see the MSM bit description in the TIMx_SMCR
register).
010: Update - The update event is selected as the trigger output (TRGO). For instance a
master timer can be used as a prescaler for a slave timer.
011: Compare pulse - The trigger output sends a positive pulse when the CC1IF flag is to
be set (even if it was already high), as soon as a capture or a compare match occurs.
(TRGO).
100: Compare - OC1REF signal is used as the trigger output (TRGO).
101: Compare - OC2REF signal is used as the trigger output (TRGO).
110: Reserved
111: Reserved
Note: The clock of the slave timer and ADC must be enabled prior to receiving events from
the master timer, and must not be changed on-the-fly while triggers are received from
the master timer.
Bits 3:0 Reserved, must be kept at reset value.
364/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
14.4.3
TIM12 slave mode control register (TIMx_SMCR)
Address offset: 0x08
Reset value: 0x0000
15
14
13
12
11
Reserved
10
9
8
7
6
MSM
rw
5
4
TS[2:0]
rw
rw
rw
3
Res.
2
1
0
SMS[2:0]
rw
rw
rw
Bits 15:8 Reserved, must be kept at reset value.
Bit 7 MSM: Master/Slave mode
0: No action
1: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect
synchronization between the current timer and its slaves (through TRGO). It is useful in
order to synchronize several timers on a single external event.
Bits 6:4 TS: Trigger selection
This bit field selects the trigger input to be used to synchronize the counter.
000: Internal Trigger 0 (ITR0)
001: Internal Trigger 1 (ITR1)
010: Internal Trigger 2 (ITR2)
011: Internal Trigger 3 (ITR3)
100: TI1 Edge Detector (TI1F_ED)
101: Filtered Timer Input 1 (TI1FP1)
110: Filtered Timer Input 2 (TI2FP2)
111: Reserved.
See Table 74: TIMx Internal trigger connection on page 366for more details on the meaning
of ITRx for each timer.
Note: These bits must be changed only when they are not used (e.g. when SMS=’000’) to
avoid wrong edge detections at the transition.
Doc ID16188 Rev 5
365/713
457
General-purpose timers (TIM12/13/14)
RM0041
Bit 3 Reserved, must be kept at reset value.
Bits 2:0 SMS: Slave mode selection
When external signals are selected, the active edge of the trigger signal (TRGI) is linked to
the polarity selected on the external input (see Input control register and Control register
descriptions.
000: Slave mode disabled - if CEN = 1 then the prescaler is clocked directly by the internal
clock
001: Reserved
010: Reserved
011: Reserved
100: Reset mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter
and generates an update of the registers
101: Gated mode - The counter clock is enabled when the trigger input (TRGI) is high. The
counter stops (but is not reset) as soon as the trigger becomes low. Counter starts and stops
are both controlled
110: Trigger mode - The counter starts on a rising edge of the trigger TRGI (but it is not
reset). Only the start of the counter is controlled
111: External clock mode 1 - Rising edges of the selected trigger (TRGI) clock the counter
Note: The Gated mode must not be used if TI1F_ED is selected as the trigger input
(TS=’100’). Indeed, TI1F_ED outputs 1 pulse for each transition on TI1F, whereas the
Gated mode checks the level of the trigger signal.
Note: The clock of the slave timer must be enabled prior to receive events from the master
timer, and must not be changed on-the-fly while triggers are received from the master
timer.
Table 74. TIMx Internal trigger connection(1)
Slave TIM
ITR0 (TS = 000)
ITR1 (TS = 001)
ITR2 (TS = 010)
ITR3 (TS = 011)
TIM12
TIM4
TIM5
TIM13_OC
TIM14_OC
1. When a timer is not present in the product, the corresponding trigger ITRx is not available.
14.4.4
TIM12 Interrupt enable register (TIMx_DIER)
Address offset: 0x0C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
TIE
Reserved
Bits 15:7
6
rw
Reserved, must be kept at reset value.
Bit 6 TIE: Trigger interrupt enable
0: Trigger interrupt disabled.
1: Trigger interrupt enabled.
Bit 5:3
366/713
Reserved, must be kept at reset value.
Doc ID16188 Rev 5
5
4
Res
3
2
1
0
CC2IE
CC1IE
UIE
rw
rw
rw
RM0041
General-purpose timers (TIM12/13/14)
Bit 2 CC2IE: Capture/Compare 2 interrupt enable
0: CC2 interrupt disabled.
1: CC2 interrupt enabled.
Bit 1 CC1IE: Capture/Compare 1 interrupt enable
0: CC1 interrupt disabled.
1: CC1 interrupt enabled.
Bit 0 UIE: Update interrupt enable
0: Update interrupt disabled.
1: Update interrupt enabled.
Doc ID16188 Rev 5
367/713
457
General-purpose timers (TIM12/13/14)
14.4.5
RM0041
TIM12 status register (TIMx_SR)
Address offset: 0x10
Reset value: 0x0000
15
14
13
Reserved
Bits 15:11
12
11
10
9
8
CC2OF CC1OF
rc_w0
rc_w0
7
Reserved
6
TIF
rc_w0
5
4
Reserved
3
2
1
0
CC2IF
CC1IF
UIF
rc_w0
rc_w0
rc_w0
Reserved, must be kept at reset value.
Bit 10 CC2OF: Capture/compare 2 overcapture flag
refer to CC1OF description
Bit 9 CC1OF: Capture/Compare 1 overcapture flag
This flag is set by hardware only when the corresponding channel is configured in input
capture mode. It is cleared by software by writing it to ‘0’.
0: No overcapture has been detected.
1: The counter value has been captured in TIMx_CCR1 register while CC1IF flag was
already set
Bits 8:7
Reserved, must be kept at reset value.
Bit 6 TIF: Trigger interrupt flag
This flag is set by hardware on trigger event (active edge detected on TRGI input when the
slave mode controller is enabled in all modes but gated mode. It is set when the counter
starts or stops when gated mode is selected. It is cleared by software.
0: No trigger event occurred.
1: Trigger interrupt pending.
Bits 5:3
368/713
Reserved, must be kept at reset value.
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Bit 2 CC2IF: Capture/Compare 2 interrupt flag
refer to CC1IF description
Bit 1 CC1IF: Capture/compare 1 interrupt flag
If channel CC1 is configured as output:
This flag is set by hardware when the counter matches the compare value. It is cleared by
software.
0: No match.
1: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register.
When the contents of TIMx_CCR1 are greater than the contents of TIMx_ARR, the CC1IF
bit goes high on the counter overflow.
If channel CC1 is configured as input:
This bit is set by hardware on a capture. It is cleared by software or by reading the
TIMx_CCR1 register.
0: No input capture occurred.
1: The counter value has been captured in TIMx_CCR1 register (an edge has been detected
on IC1 which matches the selected polarity).
Bit 0 UIF: Update interrupt flag
This bit is set by hardware on an update event. It is cleared by software.
0: No update occurred.
1: Update interrupt pending. This bit is set by hardware when the registers are updated:
– At overflow and if UDIS=’0’ in the TIMx_CR1 register.
– When CNT is reinitialized by software using the UG bit in TIMx_EGR register, if URS=’0’ and
UDIS=’0’ in the TIMx_CR1 register.
– When CNT is reinitialized by a trigger event (refer to the synchro control register
description), if URS=’0’ and UDIS=’0’ in the TIMx_CR1 register.
14.4.6
TIM event generation register (TIMx_EGR)
Address offset: 0x14
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
TG
Reserved
w
5
4
Reserved
3
2
1
0
CC2G
CC1G
UG
w
w
w
Bits 15:7 Reserved, must be kept at reset value.
Bit 6 TG: Trigger generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: The TIF flag is set in the TIMx_SR register. Related interrupt can occur if enabled
Bits 5:3 Reserved, must be kept at reset value.
Doc ID16188 Rev 5
369/713
457
General-purpose timers (TIM12/13/14)
RM0041
Bit 2 CC2G: Capture/compare 2 generation
refer to CC1G description
Bit 1 CC1G: Capture/compare 1 generation
This bit is set by software to generate an event, it is automatically cleared by hardware.
0: No action
1: A capture/compare event is generated on channel 1:
If channel CC1 is configured as output:
the CC1IF flag is set, the corresponding interrupt is sent if enabled.
If channel CC1 is configured as input:
The current counter value is captured in the TIMx_CCR1 register. The CC1IF flag is set, the
corresponding interrupt is sent if enabled. The CC1OF flag is set if the CC1IF flag was
already high.
Bit 0 UG: Update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action
1: Re-initializes the counter and generates an update of the registers. The prescaler counter
is also cleared and the prescaler ratio is not affected. The counter is cleared.
370/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
14.4.7
TIM capture/compare mode register 1 (TIMx_CCMR1)
Address offset: 0x18
Reset value: 0x0000
The channels can be used in input (capture mode) or in output (compare mode). The
direction of a channel is defined by configuring the corresponding CCxS bits. All the other
bits in this register have different functions in input and output modes. For a given bit, OCxx
describes its function when the channel is configured in output mode, ICxx describes its
function when the channel is configured in input mode. Take care that the same bit can have
different meanings for the input stage and the output stage.
15
14
Res.
13
12
OC2M[2:0]
IC2F[3:0]
rw
rw
rw
11
10
OC2PE OC2FE
IC2PSC[1:0]
rw
rw
rw
9
8
CC2S[1:0]
rw
rw
7
6
Res.
5
4
OC1M[2:0]
IC1F[3:0]
rw
rw
rw
3
2
OC1PE OC1FE
IC1PSC[1:0]
rw
rw
rw
1
0
CC1S[1:0]
rw
rw
Output compare mode
Bit 15
Reserved, must be kept at reset value.
Bits 14:12 OC2M[2:0]: Output compare 2 mode
Bit 11 OC2PE: Output compare 2 preload enable
Bit 10 OC2FE: Output compare 2 fast enable
Bits 9:8 CC2S[1:0]: Capture/Compare 2 selection
This bitfield defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output
01: CC2 channel is configured as input, IC2 is mapped on TI2
10: CC2 channel is configured as input, IC2 is mapped on TI1
11: CC2 channel is configured as input, IC2 is mapped on TRC. This mode works only if an
internal trigger input is selected through the TS bit (TIMx_SMCR register
Note: The CC2S bits are writable only when the channel is OFF (CC2E = 0 in TIMx_CCER).
Bit 7
Reserved, must be kept at reset value.
Doc ID16188 Rev 5
371/713
457
General-purpose timers (TIM12/13/14)
RM0041
Bits 6:4 OC1M: Output compare 1 mode
These bits define the behavior of the output reference signal OC1REF from which OC1 and
OC1N are derived. OC1REF is active high whereas the active levels of OC1 and OC1N
depend on the CC1P and CC1NP bits, respectively.
000: Frozen - The comparison between the output compare register TIMx_CCR1 and the
counter TIMx_CNT has no effect on the outputs.(this mode is used to generate a timing
base).
001: Set channel 1 to active level on match. The OC1REF signal is forced high when the
TIMx_CNT counter matches the capture/compare register 1 (TIMx_CCR1).
010: Set channel 1 to inactive level on match. The OC1REF signal is forced low when the
TIMx_CNT counter matches the capture/compare register 1 (TIMx_CCR1).
011: Toggle - OC1REF toggles when TIMx_CNT=TIMx_CCR1
100: Force inactive level - OC1REF is forced low
101: Force active level - OC1REF is forced high
110: PWM mode 1 - In upcounting, channel 1 is active as long as TIMx_CNT<TIMx_CCR1
else it is inactive. In downcounting, channel 1 is inactive (OC1REF=‘0) as long as
TIMx_CNT>TIMx_CCR1, else it is active (OC1REF=’1’)
111: PWM mode 2 - In upcounting, channel 1 is inactive as long as TIMx_CNT<TIMx_CCR1
else it is active. In downcounting, channel 1 is active as long as TIMx_CNT>TIMx_CCR1
else it is inactive.
Note: In PWM mode 1 or 2, the OCREF level changes only when the result of the
comparison changes or when the output compare mode switches from “frozen” mode
to “PWM” mode.
Bit 3 OC1PE: Output compare 1 preload enable
0: Preload register on TIMx_CCR1 disabled. TIMx_CCR1 can be written at anytime, the
new value is taken into account immediately
1: Preload register on TIMx_CCR1 enabled. Read/Write operations access the preload
register. TIMx_CCR1 preload value is loaded into the active register at each update event
Note: The PWM mode can be used without validating the preload register only in one-pulse
mode (OPM bit set in the TIMx_CR1 register). Else the behavior is not guaranteed.
Bit 2 OC1FE: Output compare 1 fast enable
This bit is used to accelerate the effect of an event on the trigger in input on the CC output.
0: CC1 behaves normally depending on the counter and CCR1 values even when the
trigger is ON. The minimum delay to activate the CC1 output when an edge occurs on the
trigger input is 5 clock cycles
1: An active edge on the trigger input acts like a compare match on the CC1 output. Then,
OC is set to the compare level independently of the result of the comparison. Delay to
sample the trigger input and to activate CC1 output is reduced to 3 clock cycles. OC1FE
acts only if the channel is configured in PWM1 or PWM2 mode.
Bits 1:0 CC1S: Capture/Compare 1 selection
This bitfield defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10: CC1 channel is configured as input, IC1 is mapped on TI2
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode works only if an
internal trigger input is selected through the TS bit (TIMx_SMCR register)
Note: The CC1S bits are writable only when the channel is OFF (CC1E = 0 in TIMx_CCER).
372/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Input capture mode
Bits 15:12 IC2F: Input capture 2 filter
Bits 11:10 IC2PSC[1:0]: Input capture 2 prescaler
Bits 9:8 CC2S: Capture/compare 2 selection
This bitfield defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output
01: CC2 channel is configured as input, IC2 is mapped on TI2
10: CC2 channel is configured as input, IC2 is mapped on TI1
11: CC2 channel is configured as input, IC2 is mapped on TRC. This mode works only if an
internal trigger input is selected through the TS bit (TIMx_SMCR register)
Note: The CC2S bits are writable only when the channel is OFF (CC2E = 0 in TIMx_CCER).
Bits 7:4 IC1F: Input capture 1 filter
This bitfield defines the frequency used to sample the TI1 input and the length of the digital
filter applied to TI1. The digital filter is made of an event counter in which N consecutive
events are needed to validate a transition on the output:
0000: No filter, sampling is done at fDTS
0001: fSAMPLING=fCK_INT, N=2
0010: fSAMPLING=fCK_INT, N=4
0011: fSAMPLING=fCK_INT, N=8
0100: fSAMPLING=fDTS/2, N=6
0101: fSAMPLING=fDTS/2, N=8
0110: fSAMPLING=fDTS/4, N=6
0111: fSAMPLING=fDTS/4, N=8
1000: fSAMPLING=fDTS/8, N=6
1001: fSAMPLING=fDTS/8, N=8
1010: fSAMPLING=fDTS/16, N=5
1011: fSAMPLING=fDTS/16, N=6
1100: fSAMPLING=fDTS/16, N=8
1101: fSAMPLING=fDTS/32, N=5
1110: fSAMPLING=fDTS/32, N=6
1111: fSAMPLING=fDTS/32, N=8
Bits 3:2 IC1PSC: Input capture 1 prescaler
This bitfield defines the ratio of the prescaler acting on the CC1 input (IC1).
The prescaler is reset as soon as CC1E=’0’ (TIMx_CCER register).
00: no prescaler, capture is done each time an edge is detected on the capture input
01: capture is done once every 2 events
10: capture is done once every 4 events
11: capture is done once every 8 events
Bits 1:0 CC1S: Capture/Compare 1 selection
This bitfield defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10: CC1 channel is configured as input, IC1 is mapped on TI2
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: The CC1S bits are writable only when the channel is OFF (CC1E = 0 in TIMx_CCER).
Doc ID16188 Rev 5
373/713
457
General-purpose timers (TIM12/13/14)
14.4.8
RM0041
TIM12 capture/compare enable register (TIMx_CCER)
Address offset: 0x20
Reset value: 0x0000
15
14
13
12
11
Reserved
10
9
8
7
CC2NP
rw
6
Res.
5
4
3
CC2P
CC2E
CC1NP
rw
rw
rw
2
Res.
1
0
CC1P
CC1E
rw
rw
Bits 15:8 Reserved, must be kept at reset value.
Bit 7 CC2NP: Capture/Compare 2 output Polarity
refer to CC1NP description
Bits 6 Reserved, must be kept at reset value.
Bit 5 CC2P: Capture/Compare 2 output Polarity
refer to CC1P description
Bit 4 CC2E: Capture/Compare 2 output enable
refer to CC1E description
Bit 3 CC1NP: Capture/Compare 1 complementary output Polarity
CC1 channel configured as output: CC1NP must be kept cleared
CC1 channel configured as input: CC1NP is used in conjunction with CC1P to define
TI1FP1/TI2FP1 polarity (refer to CC1P description).
Bit 2 Reserved, must be kept at reset value.
Bit 1 CC1P: Capture/Compare 1 output Polarity.
CC1 channel configured as output:
0: OC1 active high.
1: OC1 active low.
CC1 channel configured as input:
CC1NP/CC1P bits select TI1FP1 and TI2FP1 polarity for trigger or capture operations.
00: noninverted/rising edge
Circuit is sensitive to TIxFP1 rising edge (capture, trigger in reset, external clock or trigger
mode), TIxFP1 is not inverted (trigger in gated mode, encoder mode).
01: inverted/falling edge
Circuit is sensitive to TIxFP1 falling edge (capture, trigger in reset, external clock or trigger
mode), TIxFP1 is inverted (trigger in gated mode, encoder mode).
10: reserved, do not use this configuration.
Note: 11: noninverted/both edges
Circuit is sensitive to both TIxFP1 rising and falling edges (capture, trigger in reset,
external clock or trigger mode), TIxFP1 is not inverted (trigger in gated mode). This
configuration must not be used for encoder mode.
Bit 0 CC1E: Capture/Compare 1 output enable.
CC1 channel configured as output:
0: Off - OC1 is not active.
1: On - OC1 signal is output on the corresponding output pin.
CC1 channel configured as input:
This bit determines if a capture of the counter value can actually be done into the input
capture/compare register 1 (TIMx_CCR1) or not.
0: Capture disabled.
1: Capture enabled.
374/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Table 75. Output control bit for standard OCx channels
CCxE bit
OCx output state
0
Output disabled (OCx=’0’, OCx_EN=’0’)
1
OCx=OCxREF + Polarity, OCx_EN=’1’
Note:
The states of the external I/O pins connected to the standard OCx channels depend on the
state of the OCx channel and on the GPIO registers.
14.4.9
TIM12 counter (TIMx_CNT)
Address offset: 0x24
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CNT[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CNT[15:0]: Counter value
14.4.10
TIM12 prescaler (TIMx_PSC)
Address offset: 0x28
Reset value: 0x0000
15
14
13
12
11
10
9
8
PSC[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 PSC[15:0]: Prescaler value
The counter clock frequency CK_CNT is equal to fCK_PSC / (PSC[15:0] + 1).
PSC contains the value to be loaded into the active prescaler register at each update event.
PSC contains the value to be loaded in the active prescaler register at each update event
(including when the counter is cleared through UG bit of TIMx_EGR register or through
trigger controller when configured in “reset mode”).
14.4.11
TIM12 auto-reload register (TIMx_ARR)
Address offset: 0x2C
Reset value: 0x0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
ARR[15:0]
rw
Bits 15:0 ARR[15:0]: Auto-reload value
ARR is the value to be loaded into the actual auto-reload register.
Refer to the Section 14.3.1: Time-base unit for more details about ARR update and
behavior.
The counter is blocked while the auto-reload value is null.
Doc ID16188 Rev 5
375/713
457
General-purpose timers (TIM12/13/14)
14.4.12
RM0041
TIM12 capture/compare register 1 (TIMx_CCR1)
Address offset: 0x34
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR1[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR1[15:0]: Capture/Compare 1 value
If channel CC1 is configured as output:
CCR1 is the value to be loaded into the actual capture/compare 1 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR1 register
(OC1PE bit). Else the preload value is copied into the active capture/compare 1 register
when an update event occurs.
The active capture/compare register contains the value to be compared to the TIMx_CNT
counter and signaled on the OC1 output.
If channel CC1is configured as input:
CCR1 is the counter value transferred by the last input capture 1 event (IC1).
14.4.13
TIM12 capture/compare register 2 (TIMx_CCR2)
Address offset: 0x38
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR2[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR2[15:0]: Capture/Compare 2 value
If channel CC2 is configured as output:
CCR2 is the value to be loaded into the actual capture/compare 2 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR2 register
(OC2PE bit). Else the preload value is copied into the active capture/compare 2 register
when an update event occurs.
The active capture/compare register contains the value to be compared to the TIMx_CNT
counter and signalled on the OC2 output.
If channel CC2 is configured as input:
CCR2 is the counter value transferred by the last input capture 2 event (IC2).
376/713
Doc ID16188 Rev 5
RM0041
14.4.14
General-purpose timers (TIM12/13/14)
TIM12 register map
TIM12 registers are mapped as 16-bit addressable registers as described below:
0
0
0
0
0
CC2S
[1:0]
0
0
0
0
3
2
1
0
URS
UDIS
CEN
0
0
0
IC1F[3:0]
UIE
UIF
0
0
UG
CC1IE
CC1IF
0
CC1G
CC2IE
0
CC2IF
0
0
0
0
OC1FE
0
0
OC1PE
0
IC2
PSC
[1:0]
OC1M
[2:0]
0
0
0
CC1
S
[1:0]
0
0
IC1
PSC
[1:0]
CC1
S
[1:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CC1E
TIMx_ARR
0
CC1P
TIMx_PSC
0
Reserved
TIMx_CNT
0
CC1NP
Reserved
CC2E
TIMx_CCER
CC2P
Reserved
0
0
0
0
0
0
0
0
0
0
0
0
0
CNT[15:0]
Reserved
0
0
0
0
0
0
0
0
0
0
PSC[15:0]
Reserved
Reset value
0
0
0
0
0
0
0
0
0
0
ARR[15:0]
Reserved
Reset value
0x30
Reserved
0
Reserved
0
0
CC2S
[1:0]
Reserved
0
IC2F[3:0]
Reserved
Reset value
0x2C
Reserved
0
CC2NP
0
OC2FE
Reset value
OC2M
[2:0]
OC2PE
Reserved
Reset value
0x28
Reserved
0
Reset value
0x24
0
0
Reserved
0x1C
0x20
0
SMS[2:0]
CC2G
TIF
0
TG
CC1OF
0
Reserved
CC2OF
Reserved
TIMx_EGR
TIMx_CCMR1
Input Capture
mode
0
Reserved
0
0
Reset value
0x18
4
6
Reserved
0
TS[2:0]
TIE
0
TIMx_DIER
TIMx_CCMR1
Output Compare
mode
0
Reserved
Reserved
Reset value
0x14
0
MSM
TIMx_SMCR
TIMx_SR
0
0
Reset value
0x10
0
MMS[2:0]
Reserved
Reset value
0x0C
Reserved
0
Reset value
0x08
5
7
0
OPM
0
TIMx_CR2
8
CKD
[1:0]
Reserved
Reset value
0x04
9
11
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
TIMx_CR1
ARPE
0x00
Register
30
Offset
31
Table 76. TIM12 register map and reset values
0
0
0
0
0
0
0
0
0
0
Reserved
Doc ID16188 Rev 5
377/713
457
General-purpose timers (TIM12/13/14)
RM0041
1
0
6
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CCR2[15:0]
Reserved
0
0
0
0
0
0
0
Reserved
Refer to Section: Memory map for the register boundary addresses.
378/713
7
8
9
11
10
12
13
14
15
16
17
18
19
20
21
22
23
24
26
27
28
29
25
0
Reset value
0x3C to
0x4C
3
TIMx_CCR2
0
CCR1[15:0]
Reserved
Reset value
0x38
4
TIMx_CCR1
5
0x34
Register
30
Offset
31
Table 76. TIM12 register map and reset values (continued)
Doc ID16188 Rev 5
0
0
0
RM0041
General-purpose timers (TIM12/13/14)
14.5
TIM13/14 registers
The peripheral registers have to be written by half-words (16 bits) or words (32 bits). Read
accesses can be done by bytes (8 bits), half-words (16 bits) or words (32 bits).
14.5.1
TIM13/14 control register 1 (TIMx_CR1)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
11
10
Reserved
9
8
CKD[1:0]
rw
7
ARPE
rw
rw
6
5
Reserved
4
3
2
1
0
OPM
URS
UDIS
CEN
rw
rw
rw
rw
Bits 15:10 Reserved, must be kept at reset value.
Bits 9:8 CKD: Clock division
This bit-field indicates the division ratio between the timer clock (CK_INT) frequency and
sampling clock used by the digital filters (TIx),
00: tDTS = tCK_INT
01: tDTS = 2 × tCK_INT
10: tDTS = 4 × tCK_INT
11: Reserved
Bit 7 ARPE: Auto-reload preload enable
0: TIMx_ARR register is not buffered
1: TIMx_ARR register is buffered
Bits 6:4 Reserved, must be kept at reset value.
Bit 3 OPM: One-pulse mode
0: Counter is not stopped on the update event
1: Counter stops counting on the next update event (clearing the CEN bit).
Bit 2 URS: Update request source
This bit is set and cleared by software to select the update interrupt (UEV) sources.
0: Any of the following events generate an UEV if enabled:
–
Counter overflow
–
Setting the UG bit
1: Only counter overflow generates an UEV if enabled.
Bit 1 UDIS: Update disable
This bit is set and cleared by software to enable/disable update interrupt (UEV) event
generation.
0: UEV enabled. An UEV is generated by one of the following events:
–
Counter overflow
–
Setting the UG bit.
Buffered registers are then loaded with their preload values.
1: UEV disabled. No UEV is generated, shadow registers keep their value (ARR, PSC,
CCRx). The counter and the prescaler are reinitialized if the UG bit is set.
Bit 0 CEN: Counter enable
0: Counter disabled
1: Counter enabled
Doc ID16188 Rev 5
379/713
457
General-purpose timers (TIM12/13/14)
14.5.2
RM0041
TIM10/11/13/14 Interrupt enable register (TIMx_DIER)
Address offset: 0x0C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
Reserved
Bits 15:2
1
0
CC1IE
UIE
rw
rw
Reserved, must be kept at reset value.
Bit 1 CC1IE: Capture/Compare 1 interrupt enable
0: CC1 interrupt disabled
1: CC1 interrupt enabled
Bit 0 UIE: Update interrupt enable
0: Update interrupt disabled
1: Update interrupt enabled
14.5.3
TIM13/14 status register (TIMx_SR)
Address offset: 0x10
Reset value: 0x0000
15
14
13
12
Reserved
Bits 15:10
11
10
9
8
7
CC1OF
rc_w0
6
5
Reserved
4
3
2
1
0
CC1IF
UIF
rc_w0
rc_w0
Reserved, must be kept at reset value.
Bit 9 CC1OF: Capture/Compare 1 overcapture flag
This flag is set by hardware only when the corresponding channel is configured in input
capture mode. It is cleared by software by writing it to ‘0’.
0: No overcapture has been detected.
1: The counter value has been captured in TIMx_CCR1 register while CC1IF flag was
already set
380/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
Bits 8:2
Reserved, must be kept at reset value.
Bit 1 CC1IF: Capture/compare 1 interrupt flag
If channel CC1 is configured as output:
This flag is set by hardware when the counter matches the compare value. It is cleared by
software.
0: No match.
1: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register.
When the contents of TIMx_CCR1 are greater than the contents of TIMx_ARR, the CC1IF bit
goes high on the counter overflow.
If channel CC1 is configured as input:
This bit is set by hardware on a capture. It is cleared by software or by reading the
TIMx_CCR1 register.
0: No input capture occurred.
1: The counter value has been captured in TIMx_CCR1 register (an edge has been detected
on IC1 which matches the selected polarity).
Bit 0 UIF: Update interrupt flag
This bit is set by hardware on an update event. It is cleared by software.
0: No update occurred.
1: Update interrupt pending. This bit is set by hardware when the registers are updated:
–
At overflow and if UDIS=’0’ in the TIMx_CR1 register.
–
When CNT is reinitialized by software using the UG bit in TIMx_EGR register, if
URS=’0’ and UDIS=’0’ in the TIMx_CR1 register.
14.5.4
TIM13/14 event generation register (TIMx_EGR)
Address offset: 0x14
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
Reserved
6
5
4
3
2
1
0
CC1G
UG
w
w
Bits 15:2 Reserved, must be kept at reset value.
Bit 1 CC1G: Capture/compare 1 generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: A capture/compare event is generated on channel 1:
If channel CC1 is configured as output:
CC1IF flag is set, Corresponding interrupt or is sent if enabled.
If channel CC1 is configured as input:
The current value of the counter is captured in TIMx_CCR1 register. The CC1IF flag is set,
the corresponding interrupt is sent if enabled. The CC1OF flag is set if the CC1IF flag was
already high.
Bit 0 UG: Update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action
1: Re-initialize the counter and generates an update of the registers. Note that the prescaler
counter is cleared too (anyway the prescaler ratio is not affected). The counter is cleared.
Doc ID16188 Rev 5
381/713
457
General-purpose timers (TIM12/13/14)
14.5.5
RM0041
TIM13/14 capture/compare mode register 1 (TIMx_CCMR1)
Address offset: 0x18
Reset value: 0x0000
The channels can be used in input (capture mode) or in output (compare mode). The
direction of a channel is defined by configuring the corresponding CCxS bits. All the other
bits of this register have a different function in input and in output mode. For a given bit,
OCxx describes its function when the channel is configured in output, ICxx describes its
function when the channel is configured in input. So take care that the same bit can have a
different meaning for the input stage and for the output stage.
15
14
13
12
11
10
9
8
7
6
Reserved
Reserved
382/713
5
4
OC1M[2:0]
IC1F[3:0]
rw
Doc ID16188 Rev 5
rw
rw
3
2
OC1PE OC1FE
IC1PSC[1:0]
rw
rw
rw
1
0
CC1S[1:0]
rw
rw
RM0041
General-purpose timers (TIM12/13/14)
Output compare mode
Bits 15:7
Reserved, must be kept at reset value.
Bits 6:4 OC1M: Output compare 1 mode
These bits define the behavior of the output reference signal OC1REF from which OC1 is
derived. OC1REF is active high whereas OC1 active level depends on CC1P bit.
000: Frozen. The comparison between the output compare register TIMx_CCR1 and the
counter TIMx_CNT has no effect on the outputs.
001: Set channel 1 to active level on match. OC1REF signal is forced high when the counter
TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
010: Set channel 1 to inactive level on match. OC1REF signal is forced low when the
counter TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
011: Toggle - OC1REF toggles when TIMx_CNT = TIMx_CCR1.
100: Force inactive level - OC1REF is forced low.
101: Force active level - OC1REF is forced high.
110: PWM mode 1 - Channel 1 is active as long as TIMx_CNT < TIMx_CCR1 else inactive.
111: PWM mode 2 - Channel 1 is inactive as long as TIMx_CNT < TIMx_CCR1 else active.
Note: In PWM mode 1 or 2, the OCREF level changes when the result of the comparison
changes or when the output compare mode switches from frozen to PWM mode.
Bit 3 OC1PE: Output compare 1 preload enable
0: Preload register on TIMx_CCR1 disabled. TIMx_CCR1 can be written at anytime, the
new value is taken in account immediately.
1: Preload register on TIMx_CCR1 enabled. Read/Write operations access the preload
register. TIMx_CCR1 preload value is loaded in the active register at each update event.
Note: The PWM mode can be used without validating the preload register only in one pulse
mode (OPM bit set in TIMx_CR1 register). Else the behavior is not guaranteed.
Bit 2 OC1FE: Output compare 1 fast enable
This bit is used to accelerate the effect of an event on the trigger in input on the CC output.
0: CC1 behaves normally depending on counter and CCR1 values even when the trigger is
ON. The minimum delay to activate CC1 output when an edge occurs on the trigger input is
5 clock cycles.
1: An active edge on the trigger input acts like a compare match on CC1 output. OC is then
set to the compare level independently of the result of the comparison. Delay to sample the
trigger input and to activate CC1 output is reduced to 3 clock cycles. OC1FE acts only if the
channel is configured in PWM1 or PWM2 mode.
Bits 1:0 CC1S: Capture/Compare 1 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output.
01: CC1 channel is configured as input, IC1 is mapped on TI1.
10: Reserved
11: Reserved
Note: CC1S bits are writable only when the channel is OFF (CC1E = 0 in TIMx_CCER).
Doc ID16188 Rev 5
383/713
457
General-purpose timers (TIM12/13/14)
RM0041
Input capture mode
Bits 15:8
Reserved, must be kept at reset value.
Bits 7:4 IC1F: Input capture 1 filter
This bit-field defines the frequency used to sample TI1 input and the length of the digital filter
applied to TI1. The digital filter is made of an event counter in which N consecutive events
are needed to validate a transition on the output:
0000: No filter, sampling is done at fDTS
0001: fSAMPLING=fCK_INT, N=2
0010: fSAMPLING=fCK_INT, N=4
0011: fSAMPLING=fCK_INT, N=8
0100: fSAMPLING=fDTS/2, N=6
0101: fSAMPLING=fDTS/2, N=8
0110: fSAMPLING=fDTS/4, N=6
0111: fSAMPLING=fDTS/4, N=8
1000: fSAMPLING=fDTS/8, N=6
1001: fSAMPLING=fDTS/8, N=8
1010: fSAMPLING=fDTS/16, N=5
1011: fSAMPLING=fDTS/16, N=6
1100: fSAMPLING=fDTS/16, N=8
1101: fSAMPLING=fDTS/32, N=5
1110: fSAMPLING=fDTS/32, N=6
1111: fSAMPLING=fDTS/32, N=8
Bits 3:2 IC1PSC: Input capture 1 prescaler
This bit-field defines the ratio of the prescaler acting on CC1 input (IC1).
The prescaler is reset as soon as CC1E=’0’ (TIMx_CCER register).
00: no prescaler, capture is done each time an edge is detected on the capture input
01: capture is done once every 2 events
10: capture is done once every 4 events
11: capture is done once every 8 events
Bits 1:0 CC1S: Capture/Compare 1 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10:
11:
Note: CC1S bits are writable only when the channel is OFF (CC1E = 0 in TIMx_CCER).
384/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
14.5.6
TIM13/14 capture/compare enable register (TIMx_CCER)
Address offset: 0x20
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
CC1NP
Reserved
rw
2
Res.
1
0
CC1P
CC1E
rw
rw
Bits 15:4 Reserved, must be kept at reset value.
Bit 3 CC1NP: Capture/Compare 1 complementary output Polarity.
CC1 channel configured as output: CC1NP must be kept cleared.
CC1 channel configured as input: CC1NP bit is used in conjunction with CC1P to define
TI1FP1 polarity (refer to CC1P description).
Bit 2 Reserved, must be kept at reset value.
Bit 1 CC1P: Capture/Compare 1 output Polarity.
CC1 channel configured as output:
0: OC1 active high
1: OC1 active low
CC1 channel configured as input:
The CC1P bit selects TI1FP1 and TI2FP1 polarity for trigger or capture operations.
00: noninverted/rising edge
Circuit is sensitive to TI1FP1 rising edge (capture mode), TI1FP1 is not inverted.
01: inverted/falling edge
Circuit is sensitive to TI1FP1 falling edge (capture mode), TI1FP1 is inverted.
10: reserved, do not use this configuration.
11: noninverted/both edges
Circuit is sensitive to both TI1FP1 rising and falling edges (capture mode), TI1FP1 is not
inverted.
Bit 0 CC1E: Capture/Compare 1 output enable.
CC1 channel configured as output:
0: Off - OC1 is not active
1: On - OC1 signal is output on the corresponding output pin
CC1 channel configured as input:
This bit determines if a capture of the counter value can actually be done into the input
capture/compare register 1 (TIMx_CCR1) or not.
0: Capture disabled
1: Capture enabled
Table 77. Output control bit for standard OCx channels
CCxE bit
Note:
OCx output state
0
Output Disabled (OCx=’0’, OCx_EN=’0’)
1
OCx=OCxREF + Polarity, OCx_EN=’1’
The state of the external I/O pins connected to the standard OCx channels depends on the
OCx channel state and the GPIO registers.
Doc ID16188 Rev 5
385/713
457
General-purpose timers (TIM12/13/14)
14.5.7
RM0041
TIM13/14 counter (TIMx_CNT)
Address offset: 0x24
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CNT[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CNT[15:0]: Counter value
14.5.8
TIM13/14 prescaler (TIMx_PSC)
Address offset: 0x28
Reset value: 0x0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
PSC[15:0]
rw
Bits 15:0 PSC[15:0]: Prescaler value
The counter clock frequency CK_CNT is equal to fCK_PSC / (PSC[15:0] + 1).
PSC contains the value to be loaded in the active prescaler register at each update event
(including when the counter is cleared through UG bit of TIMx_EGR register or through
trigger controller when configured in “reset mode”).
14.5.9
TIM13/14 auto-reload register (TIMx_ARR)
Address offset: 0x2C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
ARR[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 ARR[15:0]: Auto-reload value
ARR is the value to be loaded in the actual auto-reload register.
Refer to Section 14.3.1: Time-base unit for more details about ARR update and behavior.
The counter is blocked while the auto-reload value is null.
386/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM12/13/14)
14.5.10
TIM13/14 capture/compare register 1 (TIMx_CCR1)
Address offset: 0x34
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR1[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR1[15:0]: Capture/Compare 1 value
If channel CC1 is configured as output:
CCR1 is the value to be loaded in the actual capture/compare 1 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR1 register (bit
OC1PE). Else the preload value is copied in the active capture/compare 1 register when an
update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signaled on OC1 output.
If channel CC1is configured as input:
CCR1 is the counter value transferred by the last input capture 1 event (IC1).
14.5.11
TIM13/14 register map
TIMx registers are mapped as 16-bit addressable registers as described in the tables below:
0x08
0
TIMx_SMCR
0
0
0
0
0
CEN
Reset value
Reserve
d
URS
CKD
[1:0]
Reserved
UDIS
TIMx_CR1
OPM
0x00
Register
ARPE
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 78. TIM13/14 register map and reset values
0
Reserved
Reserved
Reset value
0x14
TIMx_EGR
0
Reserved
Reset value
Doc ID16188 Rev 5
Reserved
UIE
0
UIF
TIMx_SR
CC1OF
0x10
0
0
0
UG
Reserved
Reset value
CC1IF
TIMx_DIER
CC1G
0x0C
CC1IE
Reset value
0
0
387/713
457
General-purpose timers (TIM12/13/14)
RM0041
0
0
IC1F[3:0]
Reserved
Reset value
0
0
0
0
TIMx_CNT
TIMx_PSC
0
TIMx_ARR
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ARR[15:0]
Reserved
0
0
0
0
0
0
0
0
0
0
Reserved
TIMx_CCR1
CCR1[15:0]
Reserved
Reset value
388/713
CC1S
[1:0]
PSC[15:0]
0
0x30
0x38 to
0x4C
0
Reserved
Reset value
0x34
0
CNT[15:0]
Reserved
Reset value
0x2C
0
0
Reserved
Reset value
0x28
0
IC1
PSC
[1:0]
CC1E
TIMx_CCER
Reset value
0x24
0
Reserved
0x1C
0x20
0
OC1FE
Reset value
TIMx_CCMR1
Input capture
mode
CC1S
[1:0]
CC1P
0x18
OC1M
[2:0]
Reserved
OC1PE
TIMx_CCMR1
Output compare
mode
CC1NP
Register
Reserved
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 78. TIM13/14 register map and reset values (continued)
0
Reserved
Doc ID16188 Rev 5
0
0
0
0
0
0
0
0
0
RM0041
15
General-purpose timers (TIM15/16/17)
General-purpose timers (TIM15/16/17)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
15.1
TIM15/16/17 introduction
The TIM15/16/17 timers consist of a 16-bit auto-reload counter driven by a programmable
prescaler.
They may be used for a variety of purposes, including measuring the pulse lengths of input
signals (input capture) or generating output waveforms (output compare, PWM,
complementary PWM with dead-time insertion).
Pulse lengths and waveform periods can be modulated from a few microseconds to several
milliseconds using the timer prescaler and the RCC clock controller prescalers.
The TIM15/16/17 timers are completely independent, and do not share any resources. They
can be synchronized together as described in Section 14.3.12.
Doc ID16188 Rev 5
389/713
457
General-purpose timers (TIM15/16/17)
15.2
RM0041
TIM15 main features
TIM15 includes the following features:
390/713
•
16-bit auto-reload upcounter
•
16-bit programmable prescaler used to divid (also “on the fly”) the counter clock
frequency by any factor between 1 and 65536
•
Up to 2 independent channels for:
–
Input capture
–
Output compare
–
PWM generation (edge mode)
–
One-pulse mode output
•
Complementary outputs with programmable dead-time (for channel 1 only)
•
Synchronization circuit to control the timer with external signals and to interconnect
several timers together
•
Repetition counter to update the timer registers only after a given number of cycles of
the counter
•
Break input to put the timer’s output signals in the reset state or a known state
•
Interrupt/DMA generation on the following events:
–
Update: counter overflow, counter initialization (by software or internal/external
trigger)
–
Trigger event (counter start, stop, initialization or count by internal/external trigger)
–
Input capture
–
Output compare
–
Break input (interrupt request)
Doc ID16188 Rev 5
RM0041
15.3
General-purpose timers (TIM15/16/17)
TIM16 and TIM17 main features
The TIM16 and TIM17 timers include the following features:
•
16-bit auto-reload upcounter
•
16-bit programmable prescaler used to divide (also “on the fly”) the counter clock
frequency by any factor between 1 and 65536
•
One channel for:
–
Input capture
–
Output compare
–
PWM generation (edge-aligned mode)
–
One-pulse mode output
•
Complementary outputs with programmable dead-time
•
Repetition counter to update the timer registers only after a given number of cycles of
the counter
•
Break input to put the timer’s output signals in the reset state or a known state
•
Interrupt/DMA generation on the following events:
–
Update: counter overflow
–
Trigger event (counter start, stop, initialization or count by internal/external trigger)
–
Input capture
–
Output compare
–
Break input
Doc ID16188 Rev 5
391/713
457
General-purpose timers (TIM15/16/17)
RM0041
Figure 157. TIM15 block diagram
Internal clock (CK_INT)
CK_TIM1121314151617 from RCC
Trigger
controller
TRGO
to other timers
ITR0
TGI
ITR
ITR1
ITR2
TRC
TRGI
ITR3
TI1F_ED
Slave
mode
controller
Reset, enable, up, count
TI1FP1
TI2FP2
REP register
U
UI
Auto-reload register
Repetition
counter
Stop, clear or up/down
CK_PSC
PSC
CK_CNT
Prescaler
TI1
Input filter &
Edge detector
TIMx_CH1
TI1FP1
TI1FP2
Prescaler
TI2
Input filter &
Edge detector
TI2FP1
TI2FP2
counter
IC1PS U
CC1I
Capture/Compare 1 register
BRK
Polarity selection
TIMx_CH1
DTG
output OC1
IC2
Prescaler
IC2PS U
TIMx_CH1N
OC1N
CC2I
CC2I
Capture/Compare 2 register
OC2REF
output
OC2
TIMx_CH2
control
TRC
TIMx_BKIN
DTG registers
OC1REF
control
TRC
TIMx_CH2
CNT
+/-
CC1I
IC1
U
BI
Clock failure event from clock controller
CSS (clock security system
Notes:
Reg
Preload registers transferred
to active registers on U event
according to control bit
event
interrupt & DMA output
ai17330
392/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Figure 158. TIM16 and TIM17 block diagram
/ŶƚĞƌŶĂůĐůŽĐŬ;<ͺ/EdͿ
ŽƵŶƚĞƌŶĂďůĞ;EͿ
ZWƌĞŐŝƐƚĞƌ
ƵƚŽͲƌĞůŽĂĚƌĞŐŝƐƚĞƌ
h
h/
ZĞƉĞƚŝƚŝŽŶ
ĐŽƵŶƚĞƌ
^ƚŽƉ͕ĐůĞĂƌŽƌƵƉͬĚŽǁŶ
<ͺW^
d/ϭ
d/Ddžͺ,ϭ
/ŶƉƵƚĨŝůƚĞƌΘ
ĞĚŐĞƐĞůĞĐƚŽƌ
d/ϭ&Wϭ
W^
ƉƌĞƐĐĂůĞƌ
<ͺEd
нͬͲ
EdĐŽƵŶƚĞƌ
ϭ/
WƌĞƐĐĂůĞƌ
/ϭW^
d'ƌĞŐŝƐƚĞƌƐ
ϭ/
h
/ϭ
h
ĂƉƚƵƌĞͬĐŽŵƉĂƌĞϭƌĞŐŝƐƚĞƌ
KϭZ&
d/Ddžͺ,ϭ
d'
KƵƚƉƵƚ Kϭ
ĐŽŶƚƌŽů
d/Ddžͺ,ϭE
KϭE
Z<
d/Ddžͺ</E
WŽůĂƌŝƚLJƐĞůĞĐƚŝŽŶ
/
/ŶƚĞƌŶĂůďƌĞĂŬĞǀĞŶƚƐŽƵƌĐĞƐ
EŽƚĞƐ͗
ZĞŐ
WƌĞůŽĂĚƌĞŐŝƐƚĞƌƐƚƌĂŶƐĨĞƌƌĞĚ
ƚŽĂĐƚŝǀĞƌĞŐŝƐƚĞƌƐŽŶhĞǀĞŶƚ
ĂĐĐŽƌĚŝŶŐƚŽĐŽŶƚƌŽůďŝƚ
ǀĞŶƚ
/ŶƚĞƌƌƵƉƚΘDŽƵƚƉƵƚ
D^ϯϭϰϭϱsϱ
Doc ID16188 Rev 5
393/713
457
General-purpose timers (TIM15/16/17)
RM0041
15.4
TIM15/16/17 functional description
15.4.1
Time-base unit
The main block of the programmable timer is a 16-bit counter with its related auto-reload
register. The counter can count up, down or both up and down. The counter clock can be
divided by a prescaler.
The counter, the auto-reload register and the prescaler register can be written or read by
software. This is true even when the counter is running.
The time-base unit includes:
•
Counter register (TIMx_CNT)
•
Prescaler register (TIMx_PSC)
•
Auto-reload register (TIMx_ARR)
•
Repetition counter register (TIMx_RCR)
The auto-reload register is preloaded. Writing to or reading from the auto-reload register
accesses the preload register. The content of the preload register are transferred into the
shadow register permanently or at each update event (UEV), depending on the auto-reload
preload enable bit (ARPE) in TIMx_CR1 register. The update event is sent when the counter
reaches the overflow (or underflow when downcounting) and if the UDIS bit equals 0 in the
TIMx_CR1 register. It can also be generated by software. The generation of the update
event is described in detailed for each configuration.
The counter is clocked by the prescaler output CK_CNT, which is enabled only when the
counter enable bit (CEN) in TIMx_CR1 register is set (refer also to the slave mode controller
description to get more details on counter enabling).
Note that the counter starts counting 1 clock cycle after setting the CEN bit in the TIMx_CR1
register.
Prescaler description
The prescaler can divide the counter clock frequency by any factor between 1 and 65536. It
is based on a 16-bit counter controlled through a 16-bit register (in the TIMx_PSC register).
It can be changed on the fly as this control register is buffered. The new prescaler ratio is
taken into account at the next update event.
Figure 159 and Figure 160 give some examples of the counter behavior when the prescaler
ratio is changed on the fly:
394/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Figure 159. Counter timing diagram with prescaler division change from 1 to 2
CK_PSC
CEN
Timer clock = CK_CNT
Counter register
F7
F8 F9 FA FB FC
00
01
02
03
Update event (UEV)
Prescaler control register
0
1
Write a new value in TIMx_PSC
Prescaler buffer
0
Prescaler counter
0
1
0
1
0
1
0
1
0
1
Figure 160. Counter timing diagram with prescaler division change from 1 to 4
CK_PSC
CEN
Timer clock = CK_CNT
Counter register
F7
F8 F9 FA FB FC
00
01
Update event (UEV)
Prescaler control register
0
3
Write a new value in TIMx_PSC
15.4.2
Prescaler buffer
0
Prescaler counter
0
3
0
1
2
3
0
1
2
3
Counter modes
Upcounting mode
In upcounting mode, the counter counts from 0 to the auto-reload value (content of the
TIMx_ARR register), then restarts from 0 and generates a counter overflow event.
If the repetition counter is used, the update event (UEV) is generated after upcounting is
repeated for the number of times programmed in the repetition counter register plus one
(TIMx_RCR + 1). Else the update event is generated at each counter overflow.
Setting the UG bit in the TIMx_EGR register (by software or by using the slave mode
controller) also generates an update event.
The UEV event can be disabled by software by setting the UDIS bit in the TIMx_CR1
register. This is to avoid updating the shadow registers while writing new values in the
Doc ID16188 Rev 5
395/713
457
General-purpose timers (TIM15/16/17)
RM0041
preload registers. Then no update event occurs until the UDIS bit has been written to 0.
However, the counter restarts from 0, as well as the counter of the prescaler (but the
prescale rate does not change). In addition, if the URS bit (update request selection) in
TIMx_CR1 register is set, setting the UG bit generates an update event UEV but without
setting the UIF flag (thus no interrupt or DMA request is sent). This is to avoid generating
both update and capture interrupts when clearing the counter on the capture event.
When an update event occurs, all the registers are updated and the update flag (UIF bit in
TIMx_SR register) is set (depending on the URS bit):
•
The repetition counter is reloaded with the content of TIMx_RCR register,
•
The auto-reload shadow register is updated with the preload value (TIMx_ARR),
•
The buffer of the prescaler is reloaded with the preload value (content of the TIMx_PSC
register).
The following figures show some examples of the counter behavior for different clock
frequencies when TIMx_ARR=0x36.
Figure 161. Counter timing diagram, internal clock divided by 1
CK_PSC
CNT_EN
Timer clock = CK_CNT
Counter register
31
32 33 34 35 36 00 01 02 03 04 05 06 07
Counter overflow
Update event (UEV)
Update interrupt flag (UIF)
Figure 162. Counter timing diagram, internal clock divided by 2
CK_PSC
CNT_EN
Timer clock = CK_CNT
Counter register
0034
Counter overflow
Update event (UEV)
Update interrupt flag (UIF)
396/713
Doc ID16188 Rev 5
0035 0036
0000
0001
0002
0003
RM0041
General-purpose timers (TIM15/16/17)
Figure 163. Counter timing diagram, internal clock divided by 4
CK_PSC
CNT_EN
Timer clock = CK_CNT
Counter register
0035
0000
0036
0001
Counter overflow
Update event (UEV)
Update interrupt flag (UIF)
Figure 164. Counter timing diagram, internal clock divided by N
CK_PSC
Timer clock = CK_CNT
Counter register
1F
00
20
Counter overflow
Update event (UEV)
Update interrupt flag (UIF)
Figure 165. Counter timing diagram, update event when ARPE=0 (TIMx_ARR not
preloaded)
CK_PSC
CEN
Timer clock = CK_CNT
Counter register
31
32 33 34 35 36 00 01 02 03 04 05 06 07
Counter overflow
Update event (UEV)
Update interrupt flag (UIF)
Auto-reload register
FF
36
Write a new value in TIMx_ARR
Doc ID16188 Rev 5
397/713
457
General-purpose timers (TIM15/16/17)
RM0041
Figure 166. Counter timing diagram, update event when ARPE=1 (TIMx_ARR
preloaded)
CK_PSC
CEN
Timer clock = CK_CNT
Counter register
F0
F1 F2 F3 F4 F5 00 01 02 03 04 05 06 07
Counter overflow
Update event (UEV)
Update interrupt flag (UIF)
Auto-reload preload register
F5
36
Auto-reload shadow register
F5
36
Write a new value in TIMx_ARR
15.4.3
Repetition counter
Section 14.3.1: Time-base unit describes how the update event (UEV) is generated with
respect to the counter overflows/underflows. It is actually generated only when the repetition
counter has reached zero. This can be useful when generating PWM signals.
This means that data are transferred from the preload registers to the shadow registers
(TIMx_ARR auto-reload register, TIMx_PSC prescaler register, but also TIMx_CCRx
capture/compare registers in compare mode) every N+1 counter overflows or underflows,
where N is the value in the TIMx_RCR repetition counter register.
The repetition counter is decremented at each counter overflow in upcounting mode.
The repetition counter is an auto-reload type; the repetition rate is maintained as defined by
the TIMx_RCR register value (refer to Figure 167). When the update event is generated by
software (by setting the UG bit in TIMx_EGR register) or by hardware through the slave
mode controller, it occurs immediately whatever the value of the repetition counter is and the
repetition counter is reloaded with the content of the TIMx_RCR register.
398/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Figure 167. Update rate examples depending on mode and TIMx_RCR register
settings
Edge-aligned mode
Upcounting
Counter
TIMx_CNT
TIMx_RCR = 0
UEV
TIMx_RCR = 1
UEV
TIMx_RCR = 2
UEV
TIMx_RCR = 3
UEV
TIMx_RCR = 3
and
re-synchronization
UEV
(by SW)
UEV
Update Event: Preload registers transferred to active registers and update interrupt generated
ai17332
15.4.4
Clock selection
The counter clock can be provided by the following clock sources:
•
Internal clock (CK_INT)
•
External clock mode1: external input pin
•
Internal trigger inputs (ITRx) (only for TIM15): using one timer as the prescaler for
another timer, for example, TIM1 can be configured to act as a prescaler for TIM15.
Refer to Using one timer as prescaler for another timer for more details.
Internal clock source (CK_INT)
If the slave mode controller is disabled (SMS=000), then the CEN, DIR (in the TIMx_CR1
register) and UG bits (in the TIMx_EGR register) are actual control bits and can be changed
only by software (except UG which remains cleared automatically). As soon as the CEN bit
is written to 1, the prescaler is clocked by the internal clock CK_INT.
Figure 144 shows the behavior of the control circuit and the upcounter in normal mode,
without prescaler.
Doc ID16188 Rev 5
399/713
457
General-purpose timers (TIM15/16/17)
RM0041
Figure 168. Control circuit in normal mode, internal clock divided by 1
Internal clock
CEN=CNT_EN
UG
CNT_INIT
Counter clock = CK_CNT = CK_PSC
Counter register
32 33 34 35 36 00 01 02 03 04 05 06 07
31
External clock source mode 1
This mode is selected when SMS=111 in the TIMx_SMCR register. The counter can count at
each rising or falling edge on a selected input.
Figure 169. TI2 external clock connection example
TIMx_SMCR
TS[2:0]
or
ITRx
TI1_ED
TI2
TI2F_Rising
Filter
ICF[3:0]
TIMx_CCMR1
Edge
Detector TI2F_Falling
0
0xx
100
TI1FP1 101
TI2FP2 110
1
CC2P
TI2F
TI1F
TRGI
or
or
encoder
mode
external clock
mode 1
CK_PSC
CK_INT
internal clock
mode
(internal clock)
TIMx_CCER
SMS[2:0]
TIMx_SMCR
For example, to configure the upcounter to count in response to a rising edge on the TI2
input, use the following procedure:
Note:
1.
Configure channel 2 to detect rising edges on the TI2 input by writing CC2S = ‘01’ in
the TIMx_CCMR1 register.
2.
Configure the input filter duration by writing the IC2F[3:0] bits in the TIMx_CCMR1
register (if no filter is needed, keep IC2F=0000).
3.
Select rising edge polarity by writing CC2P=0 in the TIMx_CCER register.
4.
Configure the timer in external clock mode 1 by writing SMS=111 in the TIMx_SMCR
register.
5.
Select TI2 as the trigger input source by writing TS=110 in the TIMx_SMCR register.
6.
Enable the counter by writing CEN=1 in the TIMx_CR1 register.
The capture prescaler is not used for triggering, so there’s no need to configure it.
When a rising edge occurs on TI2, the counter counts once and the TIF flag is set.
The delay between the rising edge on TI2 and the actual clock of the counter is due to the
resynchronization circuit on TI2 input.
400/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Figure 170. Control circuit in external clock mode 1
TI2
CNT_EN
Counter clock = CK_CNT = CK_PSC
Counter register
34
35
36
TIF
Write TIF=0
15.4.5
Capture/compare channels
Each Capture/Compare channel is built around a capture/compare register (including a
shadow register), a input stage for capture (with digital filter, multiplexing and prescaler) and
an output stage (with comparator and output control).
Figure 147 to Figure 174 give an overview of one Capture/Compare channel.
The input stage samples the corresponding TIx input to generate a filtered signal TIxF.
Then, an edge detector with polarity selection generates a signal (TIxFPx) which can be
used as trigger input by the slave mode controller or as the capture command. It is
prescaled before the capture register (ICxPS).
Figure 171. Capture/compare channel (example: channel 1 input stage)
TI1F_ED
to the slave mode controller
TI1
fDTS
filter
downcounter
ICF[3:0]
TIMx_CCMR1
TI1F
TI1F_Rising
Edge
Detector
TI1F_Falling
0
1
CC1P
(from channel 2)
TI2FP1
01
10
IC1
divider
/1, /2, /4, /8
IC1PS
TRC
11
(from slave mode
controller)
TIMx_CCER
TI2F_rising
(from channel 2)
TI2F_falling
TI1FP1
0
CC1S[1:0] ICPS[1:0]
1
TIMx_CCMR1
CC1E
TIMx_CCER
The output stage generates an intermediate waveform which is then used for reference:
OCxRef (active high). The polarity acts at the end of the chain.
Doc ID16188 Rev 5
401/713
457
General-purpose timers (TIM15/16/17)
RM0041
Figure 172. Capture/compare channel 1 main circuit
APB Bus
read CCR1H S
read CCR1L
read_in_progress
8
low
high
8
(if 16-bit)
MCU-peripheral interface
S write CCR1H
write_in_progress
Capture/compare preload register
R
R
input
mode
CC1S[1]
CC1S[0]
CC1S[1]
output
mode
compare_transfer
capture_transfer
CC1S[0]
OC1PE
OC1PE
UEV
TIM1_CCMR1
(from time
base unit)
Capture/compare shadow register
IC1PS
comparator
capture
write CCR1L
CC1E
CNT>CCR1
Counter
CNT=CCR1
CC1G
TIM1_EGR
Figure 173. Output stage of capture/compare channel (channel 1)
0
‘0’
OC1_DT
11
CNT>CCR1
CNT=CCR1
Output mode OC1REF
controller
Dead-time
generator
x0
01
1
Output
enable
circuit
OC1
Output
enable
circuit
OC1N
CC1P
TIMx_CCER
OC1N_DT
11
10
‘0’
0x
0
1
CC1NE CC1E TIMx_CCER
OC1CE OC1M[2:0]
DTG[7:0]
CC1NE CC1E
TIMx_CCMR1
TIMx_BDTR
TIMx_CCER
CC1NP MOE OSSI OSSR TIMx_BDTR
TIMx_CCER
ai17333b
Figure 174. Output stage of capture/compare channel (channel 2 for TIM15)
To the master mode
controller
0
1
OC2
CC2P
CNT > CCR2
CNT = CCR2
Output
enable
circuit
Output mode OC2_REF
controller
TIM15_CCER
CC2E TIM15_CCER
OC2M[2:0]
MOE OSSI TIM15_BDTR
TIM15_CCMR2
OIS2 TIM15_CR2
ai17334
402/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
The capture/compare block is made of one preload register and one shadow register. Write
and read always access the preload register.
In capture mode, captures are actually done in the shadow register, which is copied into the
preload register.
In compare mode, the content of the preload register is copied into the shadow register
which is compared to the counter.
15.4.6
Input capture mode
In Input capture mode, the Capture/Compare Registers (TIMx_CCRx) are used to latch the
value of the counter after a transition detected by the corresponding ICx signal. When a
capture occurs, the corresponding CCXIF flag (TIMx_SR register) is set and an interrupt or
a DMA request can be sent if they are enabled. If a capture occurs while the CCxIF flag was
already high, then the over-capture flag CCxOF (TIMx_SR register) is set. CCxIF can be
cleared by software by writing it to ‘0’ or by reading the captured data stored in the
TIMx_CCRx register. CCxOF is cleared when written it to ‘0’.
The following example shows how to capture the counter value in TIMx_CCR1 when TI1
input rises. To do this, use the following procedure:
•
Select the active input: TIMx_CCR1 must be linked to the TI1 input, so write the CC1S
bits to 01 in the TIMx_CCMR1 register. As soon as CC1S becomes different from 00,
the channel is configured in input and the TIMx_CCR1 register becomes read-only.
•
Program the needed input filter duration with respect to the signal connected to the
timer (when the input is one of the TIx (ICxF bits in the TIMx_CCMRx register). Let’s
imagine that, when toggling, the input signal is not stable during at must five internal
clock cycles. We must program a filter duration longer than these five clock cycles. We
can validate a transition on TI1 when 8 consecutive samples with the new level have
been detected (sampled at fDTS frequency). Then write IC1F bits to 0011 in the
TIMx_CCMR1 register.
•
Select the edge of the active transition on the TI1 channel by writing CC1P bit to 0 in
the TIMx_CCER register (rising edge in this case).
•
Program the input prescaler. In our example, we wish the capture to be performed at
each valid transition, so the prescaler is disabled (write IC1PS bits to ‘00’ in the
TIMx_CCMR1 register).
•
Enable capture from the counter into the capture register by setting the CC1E bit in the
TIMx_CCER register.
•
If needed, enable the related interrupt request by setting the CC1IE bit in the
TIMx_DIER register, and/or the DMA request by setting the CC1DE bit in the
TIMx_DIER register.
When an input capture occurs:
•
The TIMx_CCR1 register gets the value of the counter on the active transition.
•
CC1IF flag is set (interrupt flag). CC1OF is also set if at least two consecutive captures
occurred whereas the flag was not cleared.
•
An interrupt is generated depending on the CC1IE bit.
•
A DMA request is generated depending on the CC1DE bit.
In order to handle the overcapture, it is recommended to read the data before the
overcapture flag. This is to avoid missing an overcapture which could happen after reading
the flag and before reading the data.
Doc ID16188 Rev 5
403/713
457
General-purpose timers (TIM15/16/17)
RM0041
Note:
IC interrupt and/or DMA requests can be generated by software by setting the
corresponding CCxG bit in the TIMx_EGR register.
15.4.7
PWM input mode (only for TIM15)
This mode is a particular case of input capture mode. The procedure is the same except:
•
Two ICx signals are mapped on the same TIx input.
•
These 2 ICx signals are active on edges with opposite polarity.
•
One of the two TIxFP signals is selected as trigger input and the slave mode controller
is configured in reset mode.
For example, user can measure the period (in TIMx_CCR1 register) and the duty cycle (in
TIMx_CCR2 register) of the PWM applied on TI1 using the following procedure (depending
on CK_INT frequency and prescaler value):
•
Select the active input for TIMx_CCR1: write the CC1S bits to 01 in the TIMx_CCMR1
register (TI1 selected).
•
Select the active polarity for TI1FP1 (used both for capture in TIMx_CCR1 and counter
clear): write the CC1P bit to ‘0’ (active on rising edge).
•
Select the active input for TIMx_CCR2: write the CC2S bits to 10 in the TIMx_CCMR1
register (TI1 selected).
•
Select the active polarity for TI1FP2 (used for capture in TIMx_CCR2): write the CC2P
bit to ‘1’ (active on falling edge).
•
Select the valid trigger input: write the TS bits to 101 in the TIMx_SMCR register
(TI1FP1 selected).
•
Configure the slave mode controller in reset mode: write the SMS bits to 100 in the
TIMx_SMCR register.
•
Enable the captures: write the CC1E and CC2E bits to ‘1’ in the TIMx_CCER register.
Figure 175. PWM input mode timing
TI1
TIMx_CNT
0004
0000
0001
0002
TIMx_CCR1
0004
TIMx_CCR2
0002
IC1 capture
IC2 capture
reset counter
0003
0004
IC2 capture
pulse width
measurement
0000
IC1 capture
period
measurement
ai15413
1. The PWM input mode can be used only with the TIMx_CH1/TIMx_CH2 signals due to the fact that only
TI1FP1 and TI2FP2 are connected to the slave mode controller.
404/713
Doc ID16188 Rev 5
RM0041
15.4.8
General-purpose timers (TIM15/16/17)
Forced output mode
In output mode (CCxS bits = 00 in the TIMx_CCMRx register), each output compare signal
(OCxREF and then OCx/OCxN) can be forced to active or inactive level directly by software,
independently of any comparison between the output compare register and the counter.
To force an output compare signal (OCXREF/OCx) to its active level, user just needs to
write 101 in the OCxM bits in the corresponding TIMx_CCMRx register. Thus OCXREF is
forced high (OCxREF is always active high) and OCx get opposite value to CCxP polarity
bit.
For example: CCxP=0 (OCx active high) => OCx is forced to high level.
The OCxREF signal can be forced low by writing the OCxM bits to 100 in the TIMx_CCMRx
register.
Anyway, the comparison between the TIMx_CCRx shadow register and the counter is still
performed and allows the flag to be set. Interrupt and DMA requests can be sent
accordingly. This is described in the output compare mode section below.
15.4.9
Output compare mode
This function is used to control an output waveform or indicating when a period of time has
elapsed.
When a match is found between the capture/compare register and the counter, the output
compare function:
•
Assigns the corresponding output pin to a programmable value defined by the output
compare mode (OCxM bits in the TIMx_CCMRx register) and the output polarity (CCxP
bit in the TIMx_CCER register). The output pin can keep its level (OCXM=000), be set
active (OCxM=001), be set inactive (OCxM=010) or can toggle (OCxM=011) on match.
•
Sets a flag in the interrupt status register (CCxIF bit in the TIMx_SR register).
•
Generates an interrupt if the corresponding interrupt mask is set (CCXIE bit in the
TIMx_DIER register).
•
Sends a DMA request if the corresponding enable bit is set (CCxDE bit in the
TIMx_DIER register, CCDS bit in the TIMx_CR2 register for the DMA request
selection).
The TIMx_CCRx registers can be programmed with or without preload registers using the
OCxPE bit in the TIMx_CCMRx register.
In output compare mode, the update event UEV has no effect on OCxREF and OCx output.
The timing resolution is one count of the counter. Output compare mode can also be used to
output a single pulse (in One-pulse mode).
Procedure:
Doc ID16188 Rev 5
405/713
457
General-purpose timers (TIM15/16/17)
RM0041
1.
Select the counter clock (internal, external, prescaler).
2.
Write the desired data in the TIMx_ARR and TIMx_CCRx registers.
3.
Set the CCxIE bit if an interrupt request is to be generated.
4.
5.
Select the output mode. For example:
–
Write OCxM = 011 to toggle OCx output pin when CNT matches CCRx
–
Write OCxPE = 0 to disable preload register
–
Write CCxP = 0 to select active high polarity
–
Write CCxE = 1 to enable the output
Enable the counter by setting the CEN bit in the TIMx_CR1 register.
The TIMx_CCRx register can be updated at any time by software to control the output
waveform, provided that the preload register is not enabled (OCxPE=’0’, else TIMx_CCRx
shadow register is updated only at the next update event UEV). An example is given in
Figure 151.
Figure 176. Output compare mode, toggle on OC1.
Write B201h in the CC1R register
TIM1_CNT
TIM1_CCR1
0039
003A
003B
003A
B200
B201
B201
oc1ref=OC1
Match detected on CCR1
Interrupt generated if enabled
15.4.10
PWM mode
Pulse Width Modulation mode allows the user to generate a signal with a frequency
determined by the value of the TIMx_ARR register and a duty cycle determined by the value
of the TIMx_CCRx register.
The PWM mode can be selected independently on each channel (one PWM per OCx
output) by writing ‘110’ (PWM mode 1) or ‘111’ (PWM mode 2) in the OCxM bits in the
TIMx_CCMRx register. Enable the corresponding preload register by setting the OCxPE bit
in the TIMx_CCMRx register, and eventually the auto-reload preload register by setting the
ARPE bit in the TIMx_CR1 register.
As the preload registers are transferred to the shadow registers only when an update event
occurs, before starting the counter, initialize all the registers by setting the UG bit in the
TIMx_EGR register.
406/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
OCx polarity is software programmable using the CCxP bit in the TIMx_CCER register. It
can be programmed as active high or active low. OCx output is enabled by a combination of
the CCxE, CCxNE, MOE, OSSI and OSSR bits (TIMx_CCER and TIMx_BDTR registers).
Refer to the TIMx_CCER register description for more details.
In PWM mode (1 or 2), TIMx_CNT and TIMx_CCRx are always compared to determine
whether TIMx_CCRx ≤TIMx_CNT or TIMx_CNT ≤TIMx_CCRx (depending on the direction
of the counter).
The timer is able to generate PWM in edge-aligned mode or center-aligned mode
depending on the CMS bits in the TIMx_CR1 register.
PWM edge-aligned mode
•
Upcounting configuration
Upcounting is active when the DIR bit in the TIMx_CR1 register is low. Refer to the
Upcounting mode on page 345.
In the following example, we consider PWM mode 1. The reference PWM signal
OCxREF is high as long as TIMx_CNT < TIMx_CCRx else it becomes low. If the
compare value in TIMx_CCRx is greater than the auto-reload value (in TIMx_ARR)
then OCxREF is held at ‘1’. If the compare value is 0 then OCxRef is held at ‘0’.
Figure 152 shows some edge-aligned PWM waveforms in an example where
TIMx_ARR=8.
Figure 177. Edge-aligned PWM waveforms (ARR=8)
Counter register
CCRx=4
0
1
2
3
4
5
6
7
8
0
1
OCXREF
CCxIF
CCRx=8
CCRx>8
CCRx=0
•
OCXREF
CCxIF
OCXREF ‘
CCxIF
OCXREF ‘
CCxIF
Downcounting configuration
Downcounting is active when DIR bit in TIMx_CR1 register is high. Refer to the
Repetition counter on page 398
In PWM mode 1, the reference signal OCxRef is low as long as
TIMx_CNT > TIMx_CCRx else it becomes high. If the compare value in TIMx_CCRx is
greater than the auto-reload value in TIMx_ARR, then OCxREF is held at ‘1’. 0% PWM
is not possible in this mode.
Doc ID16188 Rev 5
407/713
457
General-purpose timers (TIM15/16/17)
15.4.11
RM0041
Complementary outputs and dead-time insertion
The TIM15/16/17 general-purpose timers can output one complementary signal and
manage the switching-off and switching-on of the outputs.
This time is generally known as dead-time and must be adjusted depending on the devices
connected to the outputs and their characteristics (intrinsic delays of level-shifters, delays
due to power switches...)
The polarity of the outputs (main output OCx or complementary OCxN) can be selected
independently for each output. This is done by writing to the CCxP and CCxNP bits in the
TIMx_CCER register.
The complementary signals OCx and OCxN are activated by a combination of several
control bits: the CCxE and CCxNE bits in the TIMx_CCER register and the MOE, OISx,
OISxN, OSSI and OSSR bits in the TIMx_BDTR and TIMx_CR2 registers. Refer to Table 80
on page 429 for more details. In particular, the dead-time is activated when switching to the
IDLE state (MOE falling down to 0).
Dead-time insertion is enabled by setting both CCxE and CCxNE bits, and the MOE bit if the
break circuit is present. There is one 8-bit field named DTG[7:0] in the TIMx_BDTR register
used to control the dead-time generation for all channels. From a reference waveform
OCxREF, it generates 2 outputs OCx and OCxN. If OCx and OCxN are active high:
•
the OCx output signal is the same as the reference signal except for the rising edge,
which is delayed relative to the reference rising edge
•
the OCxN output signal is the opposite of the reference signal except for the rising
edge, which is delayed relative to the reference falling edge.
If the delay is greater than the width of the active output (OCx or OCxN) then the
corresponding pulse is not generated.
The following figures show the relationships between the output signals of the dead-time
generator and the reference signal OCxREF. (we suppose CCxP=0, CCxNP=0, MOE=1,
CCxE=1 and CCxNE=1 in these examples).
Figure 178. Complementary output with dead-time insertion.
OCxREF
OCx
delay
OCxN
delay
Figure 179. Dead-time waveforms with delay greater than the negative pulse.
OCxREF
OCx
delay
OCxN
408/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Figure 180. Dead-time waveforms with delay greater than the positive pulse.
OCxREF
OCx
OCxN
delay
The dead-time delay is the same for each of the channels and is programmable with the
DTG bits in the TIMx_BDTR register. Refer to Section 15.5.15: TIM15 break and dead-time
register (TIM15_BDTR) on page 432 for delay calculation.
Re-directing OCxREF to OCx or OCxN
In output mode (forced, output compare or PWM), OCxREF can be re-directed to the OCx
output or to OCxN output by configuring the CCxE and CCxNE bits in the TIMx_CCER
register.
This allows the user to send a specific waveform (such as PWM or static active level) on
one output while the complementary remains at its inactive level. Other alternative
possibilities are to have both outputs at inactive level or both outputs active and
complementary with dead-time.
Note:
When only OCxN is enabled (CCxE=0, CCxNE=1), it is not complemented and becomes
active as soon as OCxREF is high. For example, if CCxNP=0 then OCxN=OCxRef. On the
other hand, when both OCx and OCxN are enabled (CCxE=CCxNE=1) OCx becomes
active when OCxREF is high whereas OCxN is complemented and becomes active when
OCxREF is low.
15.4.12
Using the break function
When using the break function, the output enable signals and inactive levels are modified
according to additional control bits (MOE, OSSI and OSSR bits in the TIMx_BDTR register,
OISx and OISxN bits in the TIMx_CR2 register). In any case, the OCx and OCxN outputs
cannot be set both to active level at a given time. Refer to Table 80: Output control bits for
complementary OCx and OCxN channels with break feature on page 429 for more details.
The break source can be either the break input pin or a clock failure event, generated by the
Clock Security System (CSS), from the Reset Clock Controller. For further information on
the Clock Security System, refer to Section 6.2.7: Clock security system (CSS).
When exiting from reset, the break circuit is disabled and the MOE bit is low. Enable the
break function by setting the BKE bit in the TIMx_BDTR register. The break input polarity
can be selected by configuring the BKP bit in the same register. BKE and BKP can be
modified at the same time. When the BKE and BKP bits are written, a delay of 1 APB clock
cycle is applied before the writing is effective. Consequently, it is necessary to wait one APB
clock period to correctly read back the bit after the write operation.
Because MOE falling edge can be asynchronous, a resynchronization circuit has been
inserted between the actual signal (acting on the outputs) and the synchronous control bit
(accessed in the TIMx_BDTR register). It results in some delays between the asynchronous
and the synchronous signals. In particular, if user writes MOE to 1 whereas it was low, a
Doc ID16188 Rev 5
409/713
457
General-purpose timers (TIM15/16/17)
RM0041
delay (dummy instruction) must be inserted before reading it correctly. This is because user
writes the asynchronous signal and reads the synchronous signal.
When a break occurs (selected level on the break input):
Note:
•
The MOE bit is cleared asynchronously, putting the outputs in inactive state, idle state
or in reset state (selected by the OSSI bit). This feature functions even if the MCU
oscillator is off.
•
Each output channel is driven with the level programmed in the OISx bit in the
TIMx_CR2 register as soon as MOE=0. If OSSI=0 then the timer releases the enable
output else the enable output remains high.
•
When complementary outputs are used:
–
The outputs are first put in reset state inactive state (depending on the polarity).
This is done asynchronously so that it works even if no clock is provided to the
timer.
–
If the timer clock is still present, then the dead-time generator is reactivated in
order to drive the outputs with the level programmed in the OISx and OISxN bits
after a dead-time. Even in this case, OCx and OCxN cannot be driven to their
active level together. Note that because of the resynchronization on MOE, the
dead-time duration is a bit longer than usual (around 2 ck_tim clock cycles).
–
If OSSI=0 then the timer releases the enable outputs else the enable outputs
remain or become high as soon as one of the CCxE or CCxNE bits is high.
•
The break status flag (BIF bit in the TIMx_SR register) is set. An interrupt can be
generated if the BIE bit in the TIMx_DIER register is set. A DMA request can be sent if
the BDE bit in the TIMx_DIER register is set.
•
If the AOE bit in the TIMx_BDTR register is set, the MOE bit is automatically set again
at the next update event UEV. This can be used to perform a regulation, for instance.
Else, MOE remains low until user writes it to ‘1’ again. In this case, it can be used for
security and user can connect the break input to an alarm from power drivers, thermal
sensors or any security components.
The break inputs is acting on level. Thus, the MOE cannot be set while the break input is
active (neither automatically nor by software). In the meantime, the status flag BIF cannot
be cleared.
The break can be generated by the BRK input which has a programmable polarity and an
enable bit BKE in the TIMx_BDTR Register.
In addition to the break input and the output management, a write protection has been
implemented inside the break circuit to safeguard the application. It allows the user to freeze
the configuration of several parameters (dead-time duration, OCx/OCxN polarities and state
when disabled, OCxM configurations, break enable and polarity). User can choose from
three levels of protection selected by the LOCK bits in the TIMx_BDTR register. Refer to
Section 15.5.15: TIM15 break and dead-time register (TIM15_BDTR) on page 432. The
LOCK bits can be written only once after an MCU reset.
The Figure 181 shows an example of behavior of the outputs in response to a break.
410/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Figure 181. Output behavior in response to a break.
BREAK (MOE
)
OCxREF
OCx
(OCxN not implemented, CCxP=0, OISx=1)
OCx
(OCxN not implemented, CCxP=0, OISx=0)
OCx
(OCxN not implemented, CCxP=1, OISx=1)
OCx
(OCxN not implemented, CCxP=1, OISx=0)
OCx
delay
delay
OCxN
(CCxE=1, CCxP=0, OISx=0, CCxNE=1, CCxNP=0, OISxN=1)
delay
OCx
delay
delay
OCxN
(CCxE=1, CCxP=0, OISx=1, CCxNE=1, CCxNP=1, OISxN=1)
delay
OCx
OCxN
(CCxE=1, CCxP=0, OISx=0, CCxNE=0, CCxNP=0, OISxN=1)
delay
OCx
OCxN
(CCxE=1, CCxP=0, OISx=1, CCxNE=0, CCxNP=0, OISxN=0)
delay
OCx
OCxN
(CCxE=1, CCxP=0, CCxNE=0, CCxNP=0, OISx=OISxN=0 or OISx=OISxN=1)
Doc ID16188 Rev 5
411/713
457
General-purpose timers (TIM15/16/17)
15.4.13
RM0041
One-pulse mode
One-pulse mode (OPM) is a particular case of the previous modes. It allows the counter to
be started in response to a stimulus and to generate a pulse with a programmable length
after a programmable delay.
Starting the counter can be controlled through the slave mode controller. Generating the
waveform can be done in output compare mode or PWM mode. Select One-pulse mode by
setting the OPM bit in the TIMx_CR1 register. This makes the counter stop automatically at
the next update event UEV.
A pulse can be correctly generated only if the compare value is different from the counter
initial value. Before starting (when the timer is waiting for the trigger), the configuration must
be:
•
In upcounting: CNT < CCRx ≤ ARR (in particular, 0 < CCRx)
•
In downcounting: CNT > CCRx
Figure 182. Example of one pulse mode.
TI2
OC1REF
Counter
OC1
TIM1_ARR
TIM1_CCR1
0
tDELAY
tPULSE
t
For example user may want to generate a positive pulse on OC1 with a length of tPULSE and
after a delay of tDELAY as soon as a positive edge is detected on the TI2 input pin.
Let’s use TI2FP2 as trigger 1:
412/713
•
Map TI2FP2 to TI2 by writing CC2S=’01’ in the TIMx_CCMR1 register.
•
TI2FP2 must detect a rising edge, write CC2P=’0’ in the TIMx_CCER register.
•
Configure TI2FP2 as trigger for the slave mode controller (TRGI) by writing TS=’110’ in
the TIMx_SMCR register.
•
TI2FP2 is used to start the counter by writing SMS to ‘110’ in the TIMx_SMCR register
(trigger mode).
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
The OPM waveform is defined by writing the compare registers (taking into account the
clock frequency and the counter prescaler).
•
The tDELAY is defined by the value written in the TIMx_CCR1 register.
•
The tPULSE is defined by the difference between the auto-reload value and the compare
value (TIMx_ARR - TIMx_CCR1).
•
Let’s say user wants to build a waveform with a transition from ‘0’ to ‘1’ when a
compare match occurs and a transition from ‘1’ to ‘0’ when the counter reaches the
auto-reload value. To do this enable PWM mode 2 by writing OC1M=111 in the
TIMx_CCMR1 register. User can optionally enable the preload registers by writing
OC1PE=’1’ in the TIMx_CCMR1 register and ARPE in the TIMx_CR1 register. In this
case user has to write the compare value in the TIMx_CCR1 register, the auto-reload
value in the TIMx_ARR register, generate an update by setting the UG bit and wait for
external trigger event on TI2. CC1P is written to ‘0’ in this example.
In our example, the DIR and CMS bits in the TIMx_CR1 register should be low.
User only wants one pulse, so write ‘1’ in the OPM bit in the TIMx_CR1 register to stop the
counter at the next update event (when the counter rolls over from the auto-reload value
back to 0).
Particular case: OCx fast enable
In One-pulse mode, the edge detection on TIx input set the CEN bit which enables the
counter. Then the comparison between the counter and the compare value makes the
output toggle. But several clock cycles are needed for these operations and it limits the
minimum delay tDELAY min we can get.
If user wants to output a waveform with the minimum delay, set the OCxFE bit in the
TIMx_CCMRx register. Then OCxRef (and OCx) are forced in response to the stimulus,
without taking in account the comparison. Its new level is the same as if a compare match
had occurred. OCxFE acts only if the channel is configured in PWM1 or PWM2 mode.
Doc ID16188 Rev 5
413/713
457
General-purpose timers (TIM15/16/17)
15.4.14
RM0041
TIM15 and external trigger synchronization (only for TIM15)
The TIM15 timer can be synchronized with an external trigger in several modes: Reset
mode, Gated mode and Trigger mode.
Slave mode: Reset mode
The counter and its prescaler can be reinitialized in response to an event on a trigger input.
Moreover, if the URS bit from the TIMx_CR1 register is low, an update event UEV is
generated. Then all the preloaded registers (TIMx_ARR, TIMx_CCRx) are updated.
In the following example, the upcounter is cleared in response to a rising edge on TI1 input:
•
Configure the channel 1 to detect rising edges on TI1. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC1F=0000). The capture
prescaler is not used for triggering, so no need to configure it. The CC1S bits select the
input capture source only, CC1S = 01 in the TIMx_CCMR1 register. Write CC1P=0 in
TIMx_CCER register to validate the polarity (and detect rising edges only).
•
Configure the timer in reset mode by writing SMS=100 in TIMx_SMCR register. Select
TI1 as the input source by writing TS=101 in TIMx_SMCR register.
•
Start the counter by writing CEN=1 in the TIMx_CR1 register.
The counter starts counting on the internal clock, then behaves normally until TI1 rising
edge. When TI1 rises, the counter is cleared and restarts from 0. In the meantime, the
trigger flag is set (TIF bit in the TIMx_SR register) and an interrupt request, or a DMA
request can be sent if enabled (depending on the TIE and TDE bits in TIMx_DIER register).
The following figure shows this behavior when the auto-reload register TIMx_ARR=0x36.
The delay between the rising edge on TI1 and the actual reset of the counter is due to the
resynchronization circuit on TI1 input.
Figure 183. Control circuit in reset mode
TI1
UG
Counter clock = ck_cnt = ck_psc
Counter register
30 31 32 33 34 35 36 00 01 02 03 00 01 02 03
TIF
414/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Slave mode: Gated mode
The counter can be enabled depending on the level of a selected input.
In the following example, the upcounter counts only when TI1 input is low:
•
Configure the channel 1 to detect low levels on TI1. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC1F=0000). The capture
prescaler is not used for triggering, so no need to configure it. The CC1S bits select the
input capture source only, CC1S=01 in TIMx_CCMR1 register. Write CC1P=1 in
TIMx_CCER register to validate the polarity (and detect low level only).
•
Configure the timer in gated mode by writing SMS=101 in TIMx_SMCR register. Select
TI1 as the input source by writing TS=101 in TIMx_SMCR register.
•
Enable the counter by writing CEN=1 in the TIMx_CR1 register (in gated mode, the
counter doesn’t start if CEN=0, whatever is the trigger input level).
The counter starts counting on the internal clock as long as TI1 is low and stops as soon as
TI1 becomes high. The TIF flag in the TIMx_SR register is set both when the counter starts
or stops.
The delay between the rising edge on TI1 and the actual stop of the counter is due to the
resynchronization circuit on TI1 input.
Figure 184. Control circuit in gated mode
TI1
cnt_en
Counter clock = ck_cnt = ck_psc
Counter register
30 31 32 33
34
35 36 37 38
TIF
Write TIF=0
Doc ID16188 Rev 5
415/713
457
General-purpose timers (TIM15/16/17)
RM0041
Slave mode: Trigger mode
The counter can start in response to an event on a selected input.
In the following example, the upcounter starts in response to a rising edge on TI2 input:
•
Configure the channel 2 to detect rising edges on TI2. Configure the input filter duration
(in this example, we don’t need any filter, so we keep IC2F=0000). The capture
prescaler is not used for triggering, so no need to configure it. The CC2S bits are
configured to select the input capture source only, CC2S=01 in TIMx_CCMR1 register.
Write CC2P=1 in TIMx_CCER register to validate the polarity (and detect low level
only).
•
Configure the timer in trigger mode by writing SMS=110 in TIMx_SMCR register. Select
TI2 as the input source by writing TS=110 in TIMx_SMCR register.
When a rising edge occurs on TI2, the counter starts counting on the internal clock and the
TIF flag is set.
The delay between the rising edge on TI2 and the actual start of the counter is due to the
resynchronization circuit on TI2 input.
Figure 185. Control circuit in trigger mode
TI2
cnt_en
Counter clock = ck_cnt = ck_psc
Counter register
34
35 36 37 38
TIF
15.4.15
Timer synchronization
The TIM timers are linked together internally for timer synchronization or chaining. Refer to
Section 13.3.15: Timer synchronization on page 314 for details.
Note:
The clock of the slave timer must be enabled prior to receiving events from the master timer,
and must not be changed on-the-fly while triggers are received from the master timer.
15.4.16
Debug mode
When the microcontroller enters debug mode (Cortex®-M3 core halted), the TIMx counter
either continues to work normally or stops, depending on DBG_TIMx_STOP configuration
bit in DBG module. For more details, refer to Section 25.15.2: Debug support for timers,
watchdog and I2C.
15.5
TIM15 registers
Refer to Section 1.1: List of abbreviations for registers for a list of abbreviations used in
register descriptions.
The peripheral registers have to be written by half-words (16 bits) or words (32 bits). Read
accesses can be done by bytes (8 bits), half-words (16 bits) or words (32 bits).
416/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
15.5.1
TIM15 control register 1 (TIM15_CR1)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
Reserved
Bits 15:10
11
10
9
8
CKD[1:0]
rw
rw
7
ARPE
rw
6
5
Reserved
4
3
2
1
0
OPM
URS
UDIS
CEN
rw
rw
rw
rw
Reserved, must be kept at reset value.
Bits 9:8 CKD[1:0]: Clock division
This bitfield indicates the division ratio between the timer clock (CK_INT) frequency and the
dead-time and sampling clock (tDTS) used by the dead-time generators and the digital filters
(TIx)
00: tDTS = tCK_INT
01: tDTS = 2*tCK_INT
10: tDTS = 4*tCK_INT
11: Reserved, do not program this value
Bit 7 ARPE: Auto-reload preload enable
0: TIMx_ARR register is not buffered
1: TIMx_ARR register is buffered
Bits 6:4
Reserved, must be kept at reset value.
Bit 3 OPM: One-pulse mode
0: Counter is not stopped at update event
1: Counter stops counting at the next update event (clearing the bit CEN)
Bit 2 URS: Update request source
This bit is set and cleared by software to select the UEV event sources.
0: Any of the following events generate an update interrupt if enabled. These events can be:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
1: Only counter overflow/underflow generates an update interrupt if enabled
Bit 1 UDIS: Update disable
This bit is set and cleared by software to enable/disable UEV event generation.
0: UEV enabled. The Update (UEV) event is generated by one of the following events:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
Buffered registers are then loaded with their preload values.
1: UEV disabled. The Update event is not generated, shadow registers keep their value
(ARR, PSC, CCRx). However the counter and the prescaler are reinitialized if the UG bit is
set or if a hardware reset is received from the slave mode controller.
Bit 0 CEN: Counter enable
0: Counter disabled
1: Counter enabled
Note: External clock and gated mode can work only if the CEN bit has been previously set by
software. However trigger mode can set the CEN bit automatically by hardware.
Doc ID16188 Rev 5
417/713
457
General-purpose timers (TIM15/16/17)
15.5.2
RM0041
TIM15 control register 2 (TIM15_CR2)
Address offset: 0x04
Reset value: 0x0000
15
14
13
Reserved
Bit 15:11
12
11
10
9
8
OIS2
OIS1N
OIS1
rw
rw
rw
7
Res.
6
5
4
MMS[2:0]
rw
rw
rw
3
2
CCDS
CCUS
rw
rw
1
Res.
0
CCPC
rw
Reserved, must be kept at reset value.
Bit 10 OIS2: Output idle state 2 (OC2 output)
0: OC2=0 when MOE=0
1: OC2=1 when MOE=0
Note: This bit cannot be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in the TIMx_BKR register).
Bit 9 OIS1N: Output Idle state 1 (OC1N output)
0: OC1N=0 after a dead-time when MOE=0
1: OC1N=1 after a dead-time when MOE=0
Note: This bit can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BKR register).
Bit 8 OIS1: Output Idle state 1 (OC1 output)
0: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0
Note: This bit can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BKR register).
Bit 7
Reserved, must be kept at reset value.
Bits 6:4 MMS[1:0]: Master mode selection
These bits allow to select the information to be sent in master mode to slave timers for
synchronization (TRGO). The combination is as follows:
000: Reset - the UG bit from the TIMx_EGR register is used as trigger output (TRGO). If the
reset is generated by the trigger input (slave mode controller configured in reset mode) then
the signal on TRGO is delayed compared to the actual reset.
001: Enable - the Counter Enable signal CNT_EN is used as trigger output (TRGO). It is
useful to start several timers at the same time or to control a window in which a slave timer is
enable. The Counter Enable signal is generated by a logic OR between CEN control bit and
the trigger input when configured in gated mode. When the Counter Enable signal is
controlled by the trigger input, there is a delay on TRGO, except if the master/slave mode is
selected (see the MSM bit description in TIMx_SMCR register).
010: Update - The update event is selected as trigger output (TRGO). For instance a master
timer can then be used as a prescaler for a slave timer.
011: Compare Pulse - The trigger output send a positive pulse when the CC1IF flag is to be
set (even if it was already high), as soon as a capture or a compare match occurred.
(TRGO).
100: Compare - OC1REF signal is used as trigger output (TRGO).
101: Compare - OC2REF signal is used as trigger output (TRGO).
Bit 3 CCDS: Capture/compare DMA selection
0: CCx DMA request sent when CCx event occurs
1: CCx DMA requests sent when update event occurs
418/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Bit 2 CCUS: Capture/compare control update selection
0: When capture/compare control bits are preloaded (CCPC=1), they are updated by setting
the COMG bit only.
1: When capture/compare control bits are preloaded (CCPC=1), they are updated by setting
the COMG bit or when an rising edge occurs on TRGI.
Note: This bit acts only on channels that have a complementary output.
Bit 1
Reserved, must be kept at reset value.
Bit 0 CCPC: Capture/compare preloaded control
0: CCxE, CCxNE and OCxM bits are not preloaded
1: CCxE, CCxNE and OCxM bits are preloaded, after having been written, they are updated
only when COM bit is set.
Note: This bit acts only on channels that have a complementary output.
15.5.3
TIM15 slave mode control register (TIM15_SMCR)
Address offset: 0x08
Reset value: 0x0000
15
14
13
12
11
Reserved
Bits 15:8
10
9
8
7
6
MSM
rw
5
4
TS[2:0]
rw
rw
rw
3
Res.
2
1
0
SMS[2:0]
rw
rw
rw
Reserved, must be kept at reset value.
Bit 7 MSM: Master/slave mode
0: No action
1: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect
synchronization between the current timer and its slaves (through TRGO). It is useful if we
want to synchronize several timers on a single external event.
Doc ID16188 Rev 5
419/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bits 6:4 TS[2:0]: Trigger selection
This bitfield selects the trigger input to be used to synchronize the counter.
000: Internal Trigger 0 (ITR0)
001: Internal Trigger 1 (ITR1)
010: Internal Trigger 2 (ITR2)
011: Internal Trigger 3 (ITR3)
100: TI1 Edge Detector (TI1F_ED)
101: Filtered Timer Input 1 (TI1FP1)
110: Filtered Timer Input 2 (TI2FP2)
See Table 79: TIMx Internal trigger connection on page 420 for more details on ITRx
meaning for each Timer.
Note: These bits must be changed only when they are not used (e.g. when SMS=000) to
avoid wrong edge detections at the transition.
Bit 3
Reserved, must be kept at reset value.
Bits 2:0 SMS: Slave mode selection
When external signals are selected the active edge of the trigger signal (TRGI) is linked to
the polarity selected on the external input (see Input Control register and Control Register
description.
000: Slave mode disabled - if CEN = ‘1’ then the prescaler is clocked directly by the internal
clock.
001: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2
level.
010: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1
level.
011: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges
depending on the level of the other input.
100: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter
and generates an update of the registers.
101: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The
counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of
the counter are controlled.
110: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not
reset). Only the start of the counter is controlled.
111: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.
Note: The gated mode must not be used if TI1F_ED is selected as the trigger input
(TS=’100’). Indeed, TI1F_ED outputs 1 pulse for each transition on TI1F, whereas the
gated mode checks the level of the trigger signal.
Table 79. TIMx Internal trigger connection
Slave TIM
ITR0 (TS = 000)(1)
ITR1 (TS = 001)(1)
ITR2 (TS = 010)
ITR3 (TS = 011)
TIM15
TIM2
TIM3
TIM16_OC
TIM17_OC
1. ITR0 and ITR1 triggers available only in high density value line devices.
420/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
15.5.4
TIM15 DMA/interrupt enable register (TIM15_DIER)
Address offset: 0x0C
Reset value: 0x0000
15
Res.
14
13
TDE
12
Reserved
rw
Bit 15
11
10
9
CC2DE CC1DE
rw
rw
8
7
6
5
UDE
BIE
TIE
COMIE
rw
rw
rw
rw
4
3
Reserved
2
1
0
CC2IE
CC1IE
UIE
rw
rw
rw
Reserved, must be kept at reset value.
Bit 14 TDE: Trigger DMA request enable
0: Trigger DMA request disabled
1: Trigger DMA request enabled
Bits 13:11
Reserved, must be kept at reset value.
Bit 10 CC2DE: Capture/Compare 2 DMA request enable
0: CC2 DMA request disabled
1: CC2 DMA request enabled
Bit 9 CC1DE: Capture/Compare 1 DMA request enable
0: CC1 DMA request disabled
1: CC1 DMA request enabled
Bit 8 UDE: Update DMA request enable
0: Update DMA request disabled
1: Update DMA request enabled
Bit 7 BIE: Break interrupt enable
0: Break interrupt disabled
1: Break interrupt enabled
Bit 6 TIE: Trigger interrupt enable
0: Trigger interrupt disabled
1: Trigger interrupt enabled
Bit 5 COMIE: COM interrupt enable
0: COM interrupt disabled
1: COM interrupt enabled
Bits 4:3
Reserved, must be kept at reset value.
Bit 2 CC2IE: Capture/Compare 2 interrupt enable
0: CC2 interrupt disabled
1: CC2 interrupt enabled
Bit 1 CC1IE: Capture/Compare 1 interrupt enable
0: CC1 interrupt disabled
1: CC1 interrupt enabled
Bit 0 UIE: Update interrupt enable
0: Update interrupt disabled
1: Update interrupt enabled
Doc ID16188 Rev 5
421/713
457
General-purpose timers (TIM15/16/17)
15.5.5
RM0041
TIM15 status register (TIM15_SR)
Address offset: 0x10
Reset value: 0x0000
15
14
13
Reserved
Bits 15:11
12
11
10
9
8
CC2OF CC1OF
rc_w0
rc_w0
Res.
7
6
5
BIF
TIF
COMIF
rc_w0
rc_w0
4
3
Reserved
2
1
0
CC2IF
CC1IF
UIF
rc_w0
rc_w0
rc_w0
Reserved, must be kept at reset value.
Bit 10 CC2OF: Capture/Compare 2 overcapture flag
refer to CC1OF description
Bit 9 CC1OF: Capture/Compare 1 overcapture flag
This flag is set by hardware only when the corresponding channel is configured in input
capture mode. It is cleared by software by writing it to ‘0’.
0: No overcapture has been detected
1: The counter value has been captured in TIMx_CCR1 register while CC1IF flag was
already set
Bit 8
Reserved, must be kept at reset value.
Bit 7 BIF: Break interrupt flag
This flag is set by hardware as soon as the break input goes active. It can be cleared by
software if the break input is not active.
0: No break event occurred
1: An active level has been detected on the break input
Bit 6 TIF: Trigger interrupt flag
This flag is set by hardware on trigger event (active edge detected on TRGI input when the
slave mode controller is enabled in all modes but gated mode, both edges in case gated
mode is selected). It is cleared by software.
0: No trigger event occurred
1: Trigger interrupt pending
Bit 5 COMIF: COM interrupt flag
This flag is set by hardware on a COM event (once the capture/compare control bits –CCxE,
CCxNE, OCxM– have been updated). It is cleared by software.
0: No COM event occurred
1: COM interrupt pending
Bits 5:3
422/713
Reserved, must be kept at reset value.
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Bit 2 CC2IF: Capture/Compare 2 interrupt flag
refer to CC1IF description
Bit 1 CC1IF: Capture/Compare 1 interrupt flag
If channel CC1 is configured as output:
This flag is set by hardware when the counter matches the compare value, with some
exception in center-aligned mode (refer to the CMS bits in the TIMx_CR1 register
description). It is cleared by software.
0: No match.
1: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register.
When the contents of TIMx_CCR1 are greater than the contents of TIMx_ARR, the CC1IF
bit goes high on the counter overflow (in upcounting and up/down-counting modes) or
underflow (in downcounting mode)
If channel CC1 is configured as input:
This bit is set by hardware on a capture. It is cleared by software or by reading the
TIMx_CCR1 register.
0: No input capture occurred
1: The counter value has been captured in TIMx_CCR1 register (An edge has been
detected on IC1 which matches the selected polarity)
Bit 0 UIF: Update interrupt flag
This bit is set by hardware on an update event. It is cleared by software.
0: No update occurred.
1: Update interrupt pending. This bit is set by hardware when the registers are updated:
– At overflow regarding the repetition counter value (update if repetition counter = 0) and if the
UDIS=0 in the TIMx_CR1 register.
– When CNT is reinitialized by software using the UG bit in TIMx_EGR register, if URS=0 and
UDIS=0 in the TIMx_CR1 register.
– When CNT is reinitialized by a trigger event (refer to Section 15.5.3: TIM15 slave mode
control register (TIM15_SMCR)), if URS=0 and UDIS=0 in the TIMx_CR1 register.
15.5.6
TIM15 event generation register (TIM15_EGR)
Address offset: 0x14
Reset value: 0x0000
15
14
13
12
11
Reserved
Bits 15:8
10
9
8
7
6
5
BG
TG
COMG
w
w
rw
4
3
Reserved
2
1
0
CC2G
CC1G
UG
w
w
w
Reserved, must be kept at reset value.
Bit 7 BG: Break generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: A break event is generated. MOE bit is cleared and BIF flag is set. Related interrupt or
DMA transfer can occur if enabled.
Bit 6 TG: Trigger generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if
enabled
Doc ID16188 Rev 5
423/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bit 5 COMG: Capture/Compare control update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action
1: When the CCPC bit is set, it is possible to update the CCxE, CCxNE and OCxM bits
Note: This bit acts only on channels that have a complementary output.
Bits 4:3
Reserved, must be kept at reset value.
Bit 2 CC2G: Capture/Compare 2 generation
refer to CC1G description
Bit 1 CC1G: Capture/Compare 1 generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action
1: A capture/compare event is generated on channel 1:
If channel CC1 is configured as output:
CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled.
If channel CC1 is configured as input:
The current value of the counter is captured in TIMx_CCR1 register. The CC1IF flag is set,
the corresponding interrupt or DMA request is sent if enabled. The CC1OF flag is set if the
CC1IF flag was already high.
Bit 0 UG: Update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action.
1: Reinitialize the counter and generates an update of the registers. Note that the prescaler
counter is cleared too (anyway the prescaler ratio is not affected). The counter is cleared if
the center-aligned mode is selected or if DIR=0 (upcounting), else it takes the auto-reload
value (TIMx_ARR) if DIR=1 (downcounting).
15.5.7
TIM15 capture/compare mode register 1 (TIM15_CCMR1)
Address offset: 0x18
Reset value: 0x0000
The channels can be used in input (capture mode) or in output (compare mode). The
direction of a channel is defined by configuring the corresponding CCxS bits. All the other
bits of this register have a different function in input and in output mode. For a given bit,
OCxx describes its function when the channel is configured in output, ICxx describes its
function when the channel is configured in input. Take care that the same bit can have a
different meaning for the input stage and for the output stage.
15
14
Res
13
12
OC2M[2:0]
IC2F[3:0]
rw
424/713
rw
rw
11
10
OC2
PE
OC2
FE
9
8
CC2S[1:0]
7
Res
IC2PSC[1:0]
rw
rw
rw
6
5
4
OC1M[2:0]
IC1F[3:0]
rw
rw
rw
Doc ID16188 Rev 5
rw
rw
3
2
OC1
PE
OC1
FE
1
0
CC1S[1:0]
IC1PSC[1:0]
rw
rw
rw
rw
rw
RM0041
General-purpose timers (TIM15/16/17)
Output compare mode:
Bit 15
Reserved, must be kept at reset value.
Bits 14:12 OC2M[2:0]: Output Compare 2 mode
Bit 11 OC2PE: Output Compare 2 preload enable
Bit 10 OC2FE: Output Compare 2 fast enable
Bits 9:8 CC2S[1:0]: Capture/Compare 2 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output.
01: CC2 channel is configured as input, IC2 is mapped on TI2.
10: CC2 channel is configured as input, IC2 is mapped on TI1.
11: CC2 channel is configured as input, IC2 is mapped on TRC. This mode is working only if
an internal trigger input is selected through the TS bit (TIMx_SMCR register)
Note: CC2S bits are writable only when the channel is OFF (CC2E = ‘0’ in TIMx_CCER).
Bit 7
Reserved, must be kept at reset value.
Bits 6:4 OC1M: Output Compare 1 mode
These bits define the behavior of the output reference signal OC1REF from which OC1 and
OC1N are derived. OC1REF is active high whereas OC1 and OC1N active level depends
on CC1P and CC1NP bits.
000: Frozen - The comparison between the output compare register TIMx_CCR1 and the
counter TIMx_CNT has no effect on the outputs.
001: Set channel 1 to active level on match. OC1REF signal is forced high when the counter
TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
010: Set channel 1 to inactive level on match. OC1REF signal is forced low when the
counter TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
011: Toggle - OC1REF toggles when TIMx_CNT=TIMx_CCR1.
100: Force inactive level - OC1REF is forced low.
101: Force active level - OC1REF is forced high.
110: PWM mode 1 - In upcounting, channel 1 is active as long as TIMx_CNT<TIMx_CCR1
else inactive. In downcounting, channel 1 is inactive (OC1REF=‘0’) as long as
TIMx_CNT>TIMx_CCR1 else active (OC1REF=’1’).
111: PWM mode 2 - In upcounting, channel 1 is inactive as long as TIMx_CNT<TIMx_CCR1
else active. In downcounting, channel 1 is active as long as TIMx_CNT>TIMx_CCR1 else
inactive.
Note: 1: These bits can not be modified as long as LOCK level 3 has been programmed
(LOCK bits in TIMx_BDTR register) and CC1S=’00’ (the channel is configured in
output).
2: In PWM mode 1 or 2, the OCREF level changes only when the result of the
comparison changes or when the output compare mode switches from “frozen” mode
to “PWM” mode.
Doc ID16188 Rev 5
425/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bit 3 OC1PE: Output Compare 1 preload enable
0: Preload register on TIMx_CCR1 disabled. TIMx_CCR1 can be written at anytime, the
new value is taken in account immediately.
1: Preload register on TIMx_CCR1 enabled. Read/Write operations access the preload
register. TIMx_CCR1 preload value is loaded in the active register at each update event.
Note: 1: These bits can not be modified as long as LOCK level 3 has been programmed
(LOCK bits in TIMx_BDTR register) and CC1S=’00’ (the channel is configured in
output).
2: The PWM mode can be used without validating the preload register only in one
pulse mode (OPM bit set in TIMx_CR1 register). Else the behavior is not guaranteed.
Bit 2 OC1FE: Output Compare 1 fast enable
This bit is used to accelerate the effect of an event on the trigger in input on the CC output.
0: CC1 behaves normally depending on counter and CCR1 values even when the trigger is
ON. The minimum delay to activate CC1 output when an edge occurs on the trigger input is
5 clock cycles.
1: An active edge on the trigger input acts like a compare match on CC1 output. Then, OC is
set to the compare level independently of the result of the comparison. Delay to sample the
trigger input and to activate CC1 output is reduced to 3 clock cycles. OCFE acts only if the
channel is configured in PWM1 or PWM2 mode.
Bits 1:0 CC1S: Capture/Compare 1 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output.
01: CC1 channel is configured as input, IC1 is mapped on TI1.
10: CC1 channel is configured as input, IC1 is mapped on TI2.
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = ‘0’ in TIMx_CCER).
Input capture mode
Bits 15:12 IC2F: Input capture 2 filter
Bits 11:10 IC2PSC[1:0]: Input capture 2 prescaler
Bits 9:8 CC2S: Capture/Compare 2 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output
01: CC2 channel is configured as input, IC2 is mapped on TI2
10: CC2 channel is configured as input, IC2 is mapped on TI1
11: CC2 channel is configured as input, IC2 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC2S bits are writable only when the channel is OFF (CC2E = ‘0’ in TIMx_CCER).
426/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Bits 7:4 IC1F[3:0]: Input capture 1 filter
This bit-field defines the frequency used to sample TI1 input and the length of the digital filter
applied to TI1. The digital filter is made of an event counter in which N consecutive events
are needed to validate a transition on the output:
0000: No filter, sampling is done at fDTS
0001: fSAMPLING=fCK_INT, N=2
0010: fSAMPLING=fCK_INT, N=4
0011: fSAMPLING=fCK_INT, N=8
0100: fSAMPLING=fDTS/2, N=6
0101: fSAMPLING=fDTS/2, N=8
0110: fSAMPLING=fDTS/4, N=6
0111: fSAMPLING=fDTS/4, N=8
1000: fSAMPLING=fDTS/8, N=6
1001: fSAMPLING=fDTS/8, N=8
1010: fSAMPLING=fDTS/16, N=5
1011: fSAMPLING=fDTS/16, N=6
1100: fSAMPLING=fDTS/16, N=8
1101: fSAMPLING=fDTS/32, N=5
1110: fSAMPLING=fDTS/32, N=6
1111: fSAMPLING=fDTS/32, N=8
Bits 3:2 IC1PSC: Input capture 1 prescaler
This bit-field defines the ratio of the prescaler acting on CC1 input (IC1).
The prescaler is reset as soon as CC1E=’0’ (TIMx_CCER register).
00: no prescaler, capture is done each time an edge is detected on the capture input
01: capture is done once every 2 events
10: capture is done once every 4 events
11: capture is done once every 8 events
Bits 1:0 CC1S: Capture/Compare 1 Selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10: CC1 channel is configured as input, IC1 is mapped on TI2
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only if
an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = ‘0’ in TIMx_CCER).
15.5.8
TIM15 capture/compare enable register (TIM15_CCER)
Address offset: 0x20
Reset value: 0x0000
15
14
13
12
11
Reserved
Bits 15:8
10
9
8
7
CC1NP
rw
6
Res;
5
4
CC2P
CC2E
rw
rw
3
2
CC1NP CC1NE
rw
rw
1
0
CC1P
CC1E
rw
rw
Reserved, must be kept at reset value.
Bit 7 CC2NP: Capture/Compare 2 complementary output polarity
refer to CC1NP description
Bit 6 Reserved, must be kept at reset value.
Bit 5 CC2P: Capture/Compare 2 output polarity
refer to CC1P description
Doc ID16188 Rev 5
427/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bit 4 CC2E: Capture/Compare 2 output enable
refer to CC1E description
Bit 3 CC1NP: Capture/Compare 1 complementary output polarity
0: OC1N active high
1: OC1N active low
Note: This bit is not writable as soon as LOCK level 2 or 3 has been programmed (LOCK bits
in TIMx_BDTR register) and CC1S=”00” (the channel is configured in output).
Bit 2 CC1NE: Capture/Compare 1 complementary output enable
0: Off - OC1N is not active. OC1N level is then function of MOE, OSSI, OSSR, OIS1, OIS1N
and CC1E bits.
1: On - OC1N signal is output on the corresponding output pin depending on MOE, OSSI,
OSSR, OIS1, OIS1N and CC1E bits.
Bit 1 CC1P: Capture/Compare 1 output polarity
CC1 channel configured as output:
0: OC1 active high
1: OC1 active low
CC1 channel configured as input:
The CC1NP/CC1P bits select the polarity of TI1FP1 and TI2FP1 for trigger or capture
operations.
00: noninverted/rising edge: circuit is sensitive to TIxFP1's rising edge (capture, trigger in
reset or trigger mode), TIxFP1 is not inverted (trigger in gated mode).
01: inverted/falling edge: circuit is sensitive to TIxFP1's falling edge (capture, trigger in reset,
or trigger mode), TIxFP1 is inverted (trigger in gated mode).
10: reserved, do not use this configuration.
11: noninverted/both edges: circuit is sensitive to both the rising and falling edges of TIxFP1
(capture, trigger in reset or trigger mode), TIxFP1 is not inverted (trigger in gated mode).
Note: This bit is not writable as soon as LOCK level 2 or 3 has been programmed (LOCK bits
in TIMx_BDTR register)..
Bit 0 CC1E: Capture/Compare 1 output enable
CC1 channel configured as output:
0: Off - OC1 is not active. OC1 level is then function of MOE, OSSI, OSSR, OIS1, OIS1N
and CC1NE bits.
1: On - OC1 signal is output on the corresponding output pin depending on MOE, OSSI,
OSSR, OIS1, OIS1N and CC1NE bits.
CC1 channel configured as input:
This bit determines if a capture of the counter value can actually be done into the input
capture/compare register 1 (TIMx_CCR1) or not.
0: Capture disabled
1: Capture enabled
428/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Table 80. Output control bits for complementary OCx and OCxN channels with break feature
Output states(1)
Control bits
MOE bit OSSI bit
1
0
OSSR
bit
CCxE bit CCxNE bit OCx output state
OCxN output state
0
0
0
Output Disabled (not
driven by the timer)
OCx=0, OCx_EN=0
Output Disabled (not driven by
the timer)
OCxN=0, OCxN_EN=0
0
0
1
Output Disabled (not
driven by the timer)
OCx=0, OCx_EN=0
OCxREF + Polarity
OCxN=OCxREF xor CCxNP,
OCxN_EN=1
Output Disabled (not driven by
the timer)
OCxN=0, OCxN_EN=0
0
1
0
OCxREF + Polarity
OCx=OCxREF xor CCxP,
OCx_EN=1
0
1
1
OCREF + Polarity + deadtime
OCx_EN=1
Complementary to OCREF (not
OCREF) + Polarity + dead-time
OCxN_EN=1
1
0
0
Output Disabled (not
driven by the timer)
OCx=CCxP, OCx_EN=0
Output Disabled (not driven by
the timer)
OCxN=CCxNP, OCxN_EN=0
1
0
1
Off-State (output enabled
with inactive state)
OCx=CCxP, OCx_EN=1
OCxREF + Polarity
OCxN=OCxREF xor CCxNP,
OCxN_EN=1
1
1
0
OCxREF + Polarity
OCx=OCxREF xor CCxP,
OCx_EN=1
Off-State (output enabled with
inactive state)
OCxN=CCxNP, OCxN_EN=1
1
1
1
OCREF + Polarity + deadtime
OCx_EN=1
Complementary to OCREF (not
OCREF) + Polarity + dead-time
OCxN_EN=1
0
0
0
0
0
1
0
1
0
0
1
1
0
0
1
0
1
1
1
0
1
1
1
X
1
X
Output Disabled (not driven by the timer)
Asynchronously: OCx=CCxP, OCx_EN=0, OCxN=CCxNP,
OCxN_EN=0
Then if the clock is present: OCx=OISx and OCxN=OISxN
after a dead-time, assuming that OISx and OISxN do not
correspond to OCX and OCxN both in active state.
Off-State (output enabled with inactive state)
Asynchronously: OCx=CCxP, OCx_EN=1, OCxN=CCxNP,
OCxN_EN=1
Then if the clock is present: OCx=OISx and OCxN=OISxN
after a dead-time, assuming that OISx and OISxN do not
correspond to OCX and OCxN both in active state
1. When both outputs of a channel are not used (CCxE = CCxNE = 0), the OISx, OISxN, CCxP and CCxNP bits must be kept
cleared.
Note:
The state of the external I/O pins connected to the complementary OCx and OCxN channels
depends on the OCx and OCxN channel state and the GPIO and AFIO registers.
Doc ID16188 Rev 5
429/713
457
General-purpose timers (TIM15/16/17)
15.5.9
RM0041
TIM15 counter (TIM15_CNT)
Address offset: 0x24
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CNT[15:0]
rw
rw
rw
Bits 15:0
15.5.10
rw
rw
rw
rw
rw
CNT[15:0]: Counter value
TIM15 prescaler (TIM15_PSC)
Address offset: 0x28
Reset value: 0x0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
PSC[15:0]
rw
Bits 15:0 PSC[15:0]: Prescaler value
The counter clock frequency (CK_CNT) is equal to fCK_PSC / (PSC[15:0] + 1).
PSC contains the value to be loaded in the active prescaler register at each update event
(including when the counter is cleared through UG bit of TIMx_EGR register or through trigger
controller when configured in “reset mode”).
15.5.11
TIM15 auto-reload register (TIM15_ARR)
Address offset: 0x2C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
ARR[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 ARR[15:0]: Auto-reload value
ARR is the value to be loaded in the actual auto-reload register.
Refer to the Section 14.3.1: Time-base unit on page 343 for more details about ARR update
and behavior.
The counter is blocked while the auto-reload value is null.
430/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
15.5.12
TIM15 repetition counter register (TIM15_RCR)
Address offset: 0x30
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
REP[7:0]
Reserved
rw
rw
rw
rw
rw
Bits 15:8 Reserved, must be kept at reset value.
Bits 7:0 REP[7:0]: Repetition counter value
These bits allow the user to set-up the update rate of the compare registers (i.e. periodic
transfers from preload to active registers) when preload registers are enable, as well as the
update interrupt generation rate, if this interrupt is enable.
Each time the REP_CNT related downcounter reaches zero, an update event is generated
and it restarts counting from REP value. As REP_CNT is reloaded with REP value only at the
repetition update event U_RC, any write to the TIMx_RCR register is not taken in account until
the next repetition update event.
It means in PWM mode (REP+1) corresponds to the number of PWM periods in edge-aligned
mode.
15.5.13
TIM15 capture/compare register 1 (TIM15_CCR1)
Address offset: 0x34
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR1[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR1[15:0]: Capture/Compare 1 value
If channel CC1 is configured as output:
CCR1 is the value to be loaded in the actual capture/compare 1 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR1 register (bit
OC1PE). Else the preload value is copied in the active capture/compare 1 register when an
update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signaled on OC1 output.
If channel CC1 is configured as input:
CCR1 is the counter value transferred by the last input capture 1 event (IC1).
Doc ID16188 Rev 5
431/713
457
General-purpose timers (TIM15/16/17)
15.5.14
RM0041
TIM15 capture/compare register 2 (TIM15_CCR2)
Address offset: 0x38
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR2[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR2[15:0]: Capture/Compare 2 value
If channel CC2 is configured as output:
CCR2 is the value to be loaded in the actual capture/compare 2 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR2 register (bit
OC2PE). Else the preload value is copied in the active capture/compare 2 register when an
update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signalled on OC2 output.
If channel CC2 is configured as input:
CCR2 is the counter value transferred by the last input capture 2 event (IC2).
15.5.15
TIM15 break and dead-time register (TIM15_BDTR)
Address offset: 0x44
Reset value: 0x0000
15
14
13
12
11
10
MOE
AOE
BKP
BKE
OSSR
OSSI
rw
rw
rw
rw
rw
rw
Note:
432/713
9
8
7
6
5
LOCK[1:0]
rw
rw
4
3
2
1
0
rw
rw
rw
DTG[7:0]
rw
rw
rw
rw
rw
As the bits AOE, BKP, BKE, OSSI, OSSR and DTG[7:0] can be write-locked depending on
the LOCK configuration, it can be necessary to configure all of them during the first write
access to the TIMx_BDTR register.
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Bit 15 MOE: Main output enable
This bit is cleared asynchronously by hardware as soon as the break input is active. It is set
by software or automatically depending on the AOE bit. It is acting only on the channels
which are configured in output.
0: OC and OCN outputs are disabled or forced to idle state
1: OC and OCN outputs are enabled if their respective enable bits are set (CCxE, CCxNE in
TIMx_CCER register)
See OC/OCN enable description for more details (Section 15.5.8: TIM15 capture/compare
enable register (TIM15_CCER) on page 427).
Bit 14 AOE: Automatic output enable
0: MOE can be set only by software
1: MOE can be set by software or automatically at the next update event (if the break input is
not be active)
Note: This bit can not be modified as long as LOCK level 1 has been programmed (LOCK bits
in TIMx_BDTR register).
Bit 13 BKP: Break polarity
0: Break input BRK is active low
1: Break input BRK is active high
Note: This bit can not be modified as long as LOCK level 1 has been programmed (LOCK bits
in TIMx_BDTR register).
Note: Any write operation to this bit takes a delay of 1 APB clock cycle to become effective.
Bit 12 BKE: Break enable
0: Break inputs (BRK and CSS clock failure event) disabled
1; Break inputs (BRK and CSS clock failure event) enabled
Note: This bit cannot be modified when LOCK level 1 has been programmed (LOCK bits in
TIMx_BDTR register).
Note: Any write operation to this bit takes a delay of 1 APB clock cycle to become effective.
Bit 11 OSSR: Off-state selection for Run mode
This bit is used when MOE=1 on channels having a complementary output which are
configured as outputs. OSSR is not implemented if no complementary output is implemented
in the timer.
See OC/OCN enable description for more details (Section 15.5.8: TIM15 capture/compare
enable register (TIM15_CCER) on page 427).
0: When inactive, OC/OCN outputs are disabled (OC/OCN enable output signal=0)
1: When inactive, OC/OCN outputs are enabled with their inactive level as soon as CCxE=1
or CCxNE=1. Then, OC/OCN enable output signal=1
Note: This bit can not be modified as soon as the LOCK level 2 has been programmed (LOCK
bits in TIMx_BDTR register).
Doc ID16188 Rev 5
433/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bit 10 OSSI: Off-state selection for Idle mode
This bit is used when MOE=0 on channels configured as outputs.
See OC/OCN enable description for more details (Section 15.5.8: TIM15 capture/compare
enable register (TIM15_CCER) on page 427).
0: When inactive, OC/OCN outputs are disabled (OC/OCN enable output signal=0)
1: When inactive, OC/OCN outputs are forced first with their idle level as soon as CCxE=1 or
CCxNE=1. OC/OCN enable output signal=1)
Note: This bit can not be modified as soon as the LOCK level 2 has been programmed (LOCK
bits in TIMx_BDTR register).
Bits 9:8 LOCK[1:0]: Lock configuration
These bits offer a write protection against software errors.
00: LOCK OFF - No bit is write protected
01: LOCK Level 1 = DTG bits in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2
register and BKE/BKP/AOE bits in TIMx_BDTR register can no longer be written
10: LOCK Level 2 = LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER
register, as long as the related channel is configured in output through the CCxS bits) as well
as OSSR and OSSI bits can no longer be written.
11: LOCK Level 3 = LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in
TIMx_CCMRx registers, as long as the related channel is configured in output through the
CCxS bits) can no longer be written.
Note: The LOCK bits can be written only once after the reset. Once the TIMx_BDTR register
has been written, their content is frozen until the next reset.
Bits 7:0 DTG[7:0]: Dead-time generator setup
This bit-field defines the duration of the dead-time inserted between the complementary
outputs. DT correspond to this duration.
DTG[7:5]=0xx => DT=DTG[7:0]x tdtg with tdtg=tDTS
DTG[7:5]=10x => DT=(64+DTG[5:0])xtdtg with Tdtg=2xtDTS
DTG[7:5]=110 => DT=(32+DTG[4:0])xtdtg with Tdtg=8xtDTS
DTG[7:5]=111 => DT=(32+DTG[4:0])xtdtg with Tdtg=16xtDTS
Example if TDTS=125ns (8MHz), dead-time possible values are:
0 to 15875 ns by 125 ns steps,
16 µs to 31750 ns by 250 ns steps,
32 µs to 63 µs by 1 µs steps,
64 µs to 126 µs by 2 µs steps
Note: This bit-field can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BDTR register).
15.5.16
TIM15 DMA control register (TIM15_DCR)
Address offset: 0x48
Reset value: 0x0000
15
14
13
12
11
Reserved
Res.
434/713
10
9
8
DBL[4:0]
rw
rw
rw
7
6
5
4
3
Reserved
rw
rw
Res.
Doc ID16188 Rev 5
2
1
0
rw
rw
DBA[4:0]
rw
rw
rw
RM0041
General-purpose timers (TIM15/16/17)
Bits 15:13 Reserved, must be kept at reset value.
Bits 12:8 DBL[4:0]: DMA burst length
This 5-bit vector defines the length of DMA transfers (the timer recognizes a burst transfer
when a read or a write access is done to the TIMx_DMAR address).
00000: 1 transfer,
00001: 2 transfers,
00010: 3 transfers,
...
10001: 18 transfers.
Bits 7:5 Reserved, must be kept at reset value.
Bits 4:0 DBA[4:0]: DMA base address
This 5-bits vector defines the base-address for DMA transfers (when read/write access are
done through the TIMx_DMAR address). DBA is defined as an offset starting from the
address of the TIMx_CR1 register.
Example:
00000: TIMx_CR1,
00001: TIMx_CR2,
00010: TIMx_SMCR,
...
15.5.17
TIM15 DMA address for full transfer (TIM15_DMAR)
Address offset: 0x4C
Reset value: 0x0000
15
14
13
12
11
10
9
rw
rw
rw
rw
rw
rw
rw
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
DMAB[15:0]
rw
rw
Bits 15:0 DMAB[15:0]: DMA register for burst accesses
A read or write operation to the DMAR register accesses the register located at the address
(TIMx_CR1 address) + (DBA + DMA index) x 4
where TIMx_CR1 address is the address of the control register 1, DBA is the DMA base
address configured in TIMx_DCR register, DMA index is automatically controlled by the
DMA transfer, and ranges from 0 to DBL (DBL configured in TIMx_DCR).
15.5.18
TIM15 register map
TIM15 registers are mapped as 16-bit addressable registers as described in the table
below:
Doc ID16188 Rev 5
435/713
457
General-purpose timers (TIM15/16/17)
RM0041
0
IC2
PSC
[1:0]
CC2S
[1:0]
0
0
0
0
Reserved
Reset value
0x24
TIM15_CNT
0x28
TIM15_PSC
0x2C
TIM15_ARR
0
436/713
0
0
0
0
0
0
0
0
0
0
0
0
0
CEN
CCPC
0
UIE
UIF
UG
CC1IE
CC1IF
CC1G
CC2IE
CC2IF
0
0
CC1
S
[1:0]
0
0
0
0
IC1
PSC
[1:0]
CC1
S
[1:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ARR[15:0]
Reserved
0
Doc ID16188 Rev 5
0
0
PSC[15:0]
Reserved
Reset value
0
0
CNT[15:0]
Reserved
Reset value
OC1M
[2:0]
IC1F[3:0]
0
Reset value
0
CC2G
0
0
OC1FE
0
0
CC1E
0
0
0
0
CC1P
0
0
0
CC2NP
0
TIM15_CCER
0
IC2F[3:0]
Reserved
Reset value
0x20
0
0
0
CC1NE
0
CC2S
[1:0]
0
0
CC1NP
Reset value
TIM15_CCMR1
Input Capture
mode
OC2FE
Reserved
OC2PE
0x18
OC2M
[2:0]
0
0
CC2E
Reserved
0
0
Reserved
0
0
Reserved
0
0
Reserved
COMIE
0
COMIF
TIE
0
COMG
BIE
0
Reset value
TIM15_CCMR1
Output
Compare mode
0
UDE
0
0
Reserved
0
0
0
CC2P
TIM15_EGR
SMS[2:0]
0
TS[2:0]
TIF
0x14
0
CC1DE
Reset value
CC2DE
Reserved
0
CC1OF
TIM15_SR
0
CC2OF
Reserved
Reset value
0x10
Reserved
TDE
TIM15_DIER
0
0
OC1PE
Reserved
Reset value
0x0C
0
TG
TIM15_SMCR
0
Reserved
0x08
URS
0
UDIS
0
MMS[2:0]
Reserved
0
0
MSM
Reset value
OPM
OIS1
Reserved
0
BIF
TIM15_CR2
0
Reserved
BG
0x04
0
CCUS
0
CCDS
0
Reserved
ARPE
0
Reset value
TI1S
CKD
[1:0]
Reserved
Reserved
TIM15_CR1
OIS2
0x00
Register
OIS1N
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 81. TIM15 register map and reset values
0
0
0
0
0
0
0
0
0
RM0041
General-purpose timers (TIM15/16/17)
Offset
0x30
Register
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 81. TIM15 register map and reset values (continued)
TIM15_RCR
REP[7:0]
Reserved
Reset value
Reset value
TIM15_DCR
0
0
TIM15_DMAR
0
0
0
0
0
LOCK
[1:0]
0
0
0
0
0
0
0
0
DBL[4:0]
Reserved
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DT[7:0]
0
0
0
0
DBA[4:0]
Reserved
0
0
0
0
0
0
0
0
0
0
0
0
DMAB[15:0]
Reserved
Reset value
0
0
0
Reset value
0x4C
0
OSSI
Reserved
0
CCR2[15:0]
0
Reset value
0x48
0
BKE
TIM15_BDTR
0
Reserved
Reset value
0x44
0
OSSR
TIM15_CCR2
0
BKP
0x38
0
CCR1[15:0]
Reserved
AOE
TIM15_CCR1
MOE
0x34
0
0
0
0
0
0
0
0
0
0
0
0
Refer to Section 2.3: Memory map for the register boundary addresses.
Doc ID16188 Rev 5
437/713
457
General-purpose timers (TIM15/16/17)
15.6
RM0041
TIM16&TIM17 registers
Refer to Section 1.1: List of abbreviations for registers for a list of abbreviations used in
register descriptions.
The peripheral registers have to be written by half-words (16 bits) or words (32 bits). Read
accesses can be done by bytes (8 bits), half-words (16 bits) or words (32 bits).
15.6.1
TIM16&TIM17 control register 1 (TIMx_CR1)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
Reserved
11
10
9
8
CKD[1:0]
rw
7
ARPE
rw
rw
6
5
Reserved
4
3
2
1
0
OPM
URS
UDIS
CEN
rw
rw
rw
rw
Bits 15:10 Reserved, must be kept at reset value.
Bits 9:8 CKD[1:0]: Clock division
This bit-field indicates the division ratio between the timer clock (CK_INT) frequency and the
dead-time and sampling clock (tDTS)used by the dead-time generators and the digital filters
(TIx),
00: tDTS=tCK_INT
01: tDTS=2*tCK_INT
10: tDTS=4*tCK_INT
11: Reserved, do not program this value
Bit 7 ARPE: Auto-reload preload enable
0: TIMx_ARR register is not buffered
1: TIMx_ARR register is buffered
Bits 6:4 Reserved, must be kept at reset value.
Bit 3 OPM: One pulse mode
0: Counter is not stopped at update event
1: Counter stops counting at the next update event (clearing the bit CEN)
438/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Bit 2 URS: Update request source
This bit is set and cleared by software to select the UEV event sources.
0: Any of the following events generate an update interrupt or DMA request if enabled.
These events can be:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
1: Only counter overflow/underflow generates an update interrupt or DMA request if
enabled.
Bit 1 UDIS: Update disable
This bit is set and cleared by software to enable/disable UEV event generation.
0: UEV enabled. The Update (UEV) event is generated by one of the following events:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
Buffered registers are then loaded with their preload values.
1: UEV disabled. The Update event is not generated, shadow registers keep their value
(ARR, PSC, CCRx). However the counter and the prescaler are reinitialized if the UG bit is
set or if a hardware reset is received from the slave mode controller.
Bit 0 CEN: Counter enable
0: Counter disabled
1: Counter enabled
Note: External clock and gated mode can work only if the CEN bit has been previously set by
software. However trigger mode can set the CEN bit automatically by hardware.
15.6.2
TIM16&TIM17 control register 2 (TIMx_CR2)
Address offset: 0x04
Reset value: 0x0000
15
14
13
12
Reserved
Bits 15:10
11
10
9
8
OIS1N
OIS1
rw
rw
7
6
5
Reserved
4
3
2
CCDS
CCUS
rw
rw
1
Res.
0
CCPC
rw
Reserved, must be kept at reset value.
Bit 9 OIS1N: Output Idle state 1 (OC1N output)
0: OC1N=0 after a dead-time when MOE=0
1: OC1N=1 after a dead-time when MOE=0
Note: This bit can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BKR register).
Bit 8 OIS1: Output Idle state 1 (OC1 output)
0: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0
Note: This bit can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BKR register).
Bits 7:4
Reserved, must be kept at reset value.
Doc ID16188 Rev 5
439/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bit 3 CCDS: Capture/compare DMA selection
0: CCx DMA request sent when CCx event occurs
1: CCx DMA requests sent when update event occurs
Bit 2 CCUS: Capture/compare control update selection
0: When capture/compare control bits are preloaded (CCPC=1), they are updated by setting
the COMG bit only.
1: When capture/compare control bits are preloaded (CCPC=1), they are updated by setting
the COMG bit or when an rising edge occurs on TRGI.
Note: This bit acts only on channels that have a complementary output.
Bit 1
Reserved, must be kept at reset value.
Bit 0 CCPC: Capture/compare preloaded control
0: CCxE, CCxNE and OCxM bits are not preloaded
1: CCxE, CCxNE and OCxM bits are preloaded, after having been written, they are updated
only when COM bit is set.
Note: This bit acts only on channels that have a complementary output.
440/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
15.6.3
TIM16&TIM17 DMA/interrupt enable register (TIMx_DIER)
Address offset: 0x0C
Reset value: 0x0000
15
Res.
14
TDE
rw
13
12
11
Reserved
10
9
8
7
6
5
CC1DE
UDE
BIE
TIE
COMIE
rw
rw
rw
rw
rw
4
3
Reserved
2
1
0
CC1IE
UIE
rw
rw
Bit 15 Reserved, must be kept at reset value.
Bit 14 TDE: Trigger DMA request enable
0: Trigger DMA request disabled
1: Trigger DMA request enabled
Bist 13:10 Reserved, must be kept at reset value.
Bit 9 CC1DE: Capture/Compare 1 DMA request enable
0: CC1 DMA request disabled
1: CC1 DMA request enabled
Bit 8 UDE: Update DMA request enable
0: Update DMA request disabled
1: Update DMA request enabled
Bit 7 BIE: Break interrupt enable
0: Break interrupt disabled
1: Break interrupt enabled
Bit 6 TIE: Trigger interrupt enable
0: Trigger interrupt disabled
1: Trigger interrupt enabled
Bit 5 COMIE: COM interrupt enable
0: COM interrupt disabled
1: COM interrupt enabled
Bits 4:2 Reserved, must be kept at reset value.
Bit 1 CC1IE: Capture/Compare 1 interrupt enable
0: CC1 interrupt disabled
1: CC1 interrupt enabled
Bit 0 UIE: Update interrupt enable
0: Update interrupt disabled
1: Update interrupt enabled
Doc ID16188 Rev 5
441/713
457
General-purpose timers (TIM15/16/17)
15.6.4
RM0041
TIM16&TIM17 status register (TIMx_SR)
Address offset: 0x10
Reset value: 0x0000
15
14
13
12
Reserved
11
10
9
8
CC1OF
rc_w0
Res.
7
6
5
BIF
TIF
COMIF
rc_w0
rc_w0
rc_w0
4
3
Reserved
2
1
0
CC1IF
UIF
rc_w0
rc_w0
Bits 15:10 Reserved, must be kept at reset value.
Bit 9 CC1OF: Capture/Compare 1 overcapture flag
This flag is set by hardware only when the corresponding channel is configured in input
capture mode. It is cleared by software by writing it to ‘0’.
0: No overcapture has been detected
1: The counter value has been captured in TIMx_CCR1 register while CC1IF flag was
already set
Bit 8 Reserved, must be kept at reset value.
Bit 7 BIF: Break interrupt flag
This flag is set by hardware as soon as the break input goes active. It can be cleared by
software if the break input is not active.
0: No break event occurred
1: An active level has been detected on the break input
Bit 6 TIF: Trigger interrupt flag
This flag is set by hardware on trigger event (active edge detected on TRGI input when the
slave mode controller is enabled in all modes but gated mode, both edges in case gated
mode is selected). It is cleared by software.
0: No trigger event occurred
1: Trigger interrupt pending
Bit 5 COMIF: COM interrupt flag
This flag is set by hardware on a COM event (once the capture/compare control bits –CCxE,
CCxNE, OCxM– have been updated). It is cleared by software.
0: No COM event occurred
1: COM interrupt pending
442/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Bits 4:2 Reserved, must be kept at reset value.
Bit 1 CC1IF: Capture/Compare 1 interrupt flag
If channel CC1 is configured as output:
This flag is set by hardware when the counter matches the compare value, with some
exception in center-aligned mode (refer to the CMS bits in the TIMx_CR1 register
description). It is cleared by software.
0: No match.
1: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register.
When the contents of TIMx_CCR1 are greater than the contents of TIMx_ARR, the CC1IF
bit goes high on the counter overflow (in upcounting and up/down-counting modes) or
underflow (in downcounting mode)
If channel CC1 is configured as input:
This bit is set by hardware on a capture. It is cleared by software or by reading the
TIMx_CCR1 register.
0: No input capture occurred
1: The counter value has been captured in TIMx_CCR1 register (An edge has been
detected on IC1 which matches the selected polarity)
Bit 0 UIF: Update interrupt flag
This bit is set by hardware on an update event. It is cleared by software.
0: No update occurred.
1: Update interrupt pending. This bit is set by hardware when the registers are updated:
–
At overflow regarding the repetition counter value (update if repetition counter = 0)
and if the UDIS=0 in the TIMx_CR1 register.
–
When CNT is reinitialized by software using the UG bit in TIMx_EGR register, if
URS=0 and UDIS=0 in the TIMx_CR1 register.
–
When CNT is reinitialized by a trigger event (refer to Section 15.5.3: TIM15 slave
mode control register (TIM15_SMCR)), if URS=0 and UDIS=0 in the TIMx_CR1
register.
15.6.5
TIM16&TIM17 event generation register (TIMx_EGR)
Address offset: 0x14
Reset value: 0x0000
15
14
13
12
11
Reserved
10
9
8
7
6
5
BG
TG
COMG
w
w
w
4
3
Reserved
2
1
0
CC1G
UG
w
w
Bits 15:8 Reserved, must be kept at reset value.
Bit 7 BG: Break generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action.
1: A break event is generated. MOE bit is cleared and BIF flag is set. Related interrupt or
DMA transfer can occur if enabled.
Bit 6 TG: Trigger generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action.
1: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if
enabled.
Doc ID16188 Rev 5
443/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bit 5 COMG: Capture/Compare control update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action
1: When the CCPC bit is set, it is possible to update the CCxE, CCxNE and OCxM bits
Note: This bit acts only on channels that have a complementary output.
Bits 4:2 Reserved, must be kept at reset value.
Bit 1 CC1G: Capture/Compare 1 generation
This bit is set by software in order to generate an event, it is automatically cleared by
hardware.
0: No action.
1: A capture/compare event is generated on channel 1:
If channel CC1 is configured as output:
CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled.
If channel CC1 is configured as input:
The current value of the counter is captured in TIMx_CCR1 register. The CC1IF flag is set,
the corresponding interrupt or DMA request is sent if enabled. The CC1OF flag is set if the
CC1IF flag was already high.
Bit 0 UG: Update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action.
1: Reinitialize the counter and generates an update of the registers. Note that the prescaler
counter is cleared too (anyway the prescaler ratio is not affected). The counter is cleared if
the center-aligned mode is selected or if DIR=0 (upcounting), else it takes the auto-reload
value (TIMx_ARR) if DIR=1 (downcounting).
15.6.6
TIM16&TIM17 capture/compare mode register 1 (TIMx_CCMR1)
Address offset: 0x18
Reset value: 0x0000
The channels can be used in input (capture mode) or in output (compare mode). The
direction of a channel is defined by configuring the corresponding CCxS bits. All the other
bits of this register have a different function in input and in output mode. For a given bit,
OCxx describes its function when the channel is configured in output, ICxx describes its
function when the channel is configured in input. Take care that the same bit can have a
different meaning for the input stage and for the output stage.
15
14
13
12
11
10
9
8
7
6
Res
Reserved
4
OC1M[2:0]
Doc ID16188 Rev 5
rw
rw
3
2
OC1PE OC1FE
IC1F[3:0]
rw
444/713
5
IC1PSC[1:0]
rw
rw
rw
1
0
CC1S[1:0]
rw
rw
RM0041
General-purpose timers (TIM15/16/17)
Output compare mode:
Bits 15:7 Reserved, must be kept at reset value.
Bits 6:4 OC1M: Output Compare 1 mode
These bits define the behavior of the output reference signal OC1REF from which OC1 and
OC1N are derived. OC1REF is active high whereas OC1 and OC1N active level depends
on CC1P and CC1NP bits.
000: Frozen - The comparison between the output compare register TIMx_CCR1 and the
counter TIMx_CNT has no effect on the outputs.
001: Set channel 1 to active level on match. OC1REF signal is forced high when the
counter TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
010: Set channel 1 to inactive level on match. OC1REF signal is forced low when the
counter TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
011: Toggle - OC1REF toggles when TIMx_CNT=TIMx_CCR1.
100: Force inactive level - OC1REF is forced low.
101: Force active level - OC1REF is forced high.
110: PWM mode 1 - In upcounting, channel 1 is active as long as TIMx_CNT<TIMx_CCR1
else inactive. In downcounting, channel 1 is inactive (OC1REF=‘0’) as long as
TIMx_CNT>TIMx_CCR1 else active (OC1REF=’1’).
111: PWM mode 2 - In upcounting, channel 1 is inactive as long as
TIMx_CNT<TIMx_CCR1 else active. In downcounting, channel 1 is active as long as
TIMx_CNT>TIMx_CCR1 else inactive.
Note: 1: These bits can not be modified as long as LOCK level 3 has been programmed
(LOCK bits in TIMx_BDTR register) and CC1S=’00’ (the channel is configured in
output).
2: In PWM mode 1 or 2, the OCREF level changes only when the result of the
comparison changes or when the output compare mode switches from “frozen” mode
to “PWM” mode.
Doc ID16188 Rev 5
445/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bit 3 OC1PE: Output Compare 1 preload enable
0: Preload register on TIMx_CCR1 disabled. TIMx_CCR1 can be written at anytime, the
new value is taken in account immediately.
1: Preload register on TIMx_CCR1 enabled. Read/Write operations access the preload
register. TIMx_CCR1 preload value is loaded in the active register at each update event.
Note: 1: These bits can not be modified as long as LOCK level 3 has been programmed
(LOCK bits in TIMx_BDTR register) and CC1S=’00’ (the channel is configured in
output).
2: The PWM mode can be used without validating the preload register only in one
pulse mode (OPM bit set in TIMx_CR1 register). Else the behavior is not guaranteed.
Bit 2 OC1FE: Output Compare 1 fast enable
This bit is used to accelerate the effect of an event on the trigger in input on the CC output.
0: CC1 behaves normally depending on counter and CCR1 values even when the trigger is
ON. The minimum delay to activate CC1 output when an edge occurs on the trigger input is
5 clock cycles.
1: An active edge on the trigger input acts like a compare match on CC1 output. Then, OC
is set to the compare level independently of the result of the comparison. Delay to sample
the trigger input and to activate CC1 output is reduced to 3 clock cycles. OC1FE acts only if
the channel is configured in PWM1 or PWM2 mode.
Bits 1:0 CC1S: Capture/Compare 1 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10: CC1 channel is configured as input, IC1 is mapped on TI2
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only
if an internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = ‘0’ in TIMx_CCER).
446/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Input capture mode
Bits 15:8 Reserved, must be kept at reset value.
Bits 7:4 IC1F[3:0]: Input capture 1 filter
This bit-field defines the frequency used to sample TI1 input and the length of the digital filter applied
to TI1. The digital filter is made of an event counter in which N consecutive events are needed to
validate a transition on the output:
0000: No filter, sampling is done at fDTS
0001: fSAMPLING=fCK_INT, N=2
0010: fSAMPLING=fCK_INT, N=4
0011: fSAMPLING=fCK_INT, N=8
0100: fSAMPLING=fDTS/2, N=6
0101: fSAMPLING=fDTS/2, N=8
0110: fSAMPLING=fDTS/4, N=6
0111: fSAMPLING=fDTS/4, N=8
1000: fSAMPLING=fDTS/8, N=6
1001: fSAMPLING=fDTS/8, N=8
1010: fSAMPLING=fDTS/16, N=5
1011: fSAMPLING=fDTS/16, N=6
1100: fSAMPLING=fDTS/16, N=8
1101: fSAMPLING=fDTS/32, N=5
1110: fSAMPLING=fDTS/32, N=6
1111: fSAMPLING=fDTS/32, N=8
Bits 3:2 IC1PSC: Input capture 1 prescaler
This bit-field defines the ratio of the prescaler acting on CC1 input (IC1).
The prescaler is reset as soon as CC1E=’0’ (TIMx_CCER register).
00: no prescaler, capture is done each time an edge is detected on the capture input.
01: capture is done once every 2 events
10: capture is done once every 4 events
11: capture is done once every 8 events
Bits 1:0 CC1S: Capture/Compare 1 Selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, IC1 is mapped on TI1
10: CC1 channel is configured as input, IC1 is mapped on TI2
11: CC1 channel is configured as input, IC1 is mapped on TRC. This mode is working only if an
internal trigger input is selected through TS bit (TIMx_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = ‘0’ in TIMx_CCER).
15.6.7
TIM16&TIM17 capture/compare enable register (TIMx_CCER)
Address offset: 0x20
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
CC1NP CC1NE
Reserved
rw
Doc ID16188 Rev 5
rw
1
0
CC1P
CC1E
rw
rw
447/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bits 15:4 Reserved, must be kept at reset value.
Bit 3 CC1NP: Capture/Compare 1 complementary output polarity
0: OC1N active high
1: OC1N active low
Note: This bit is not writable as soon as LOCK level 2 or 3 has been programmed (LOCK bits
in TIMx_BDTR register) and CC1S=”00” (the channel is configured in output).
Bit 2 CC1NE: Capture/Compare 1 complementary output enable
0: Off - OC1N is not active. OC1N level is then function of MOE, OSSI, OSSR, OIS1, OIS1N
and CC1E bits.
1: On - OC1N signal is output on the corresponding output pin depending on MOE, OSSI,
OSSR, OIS1, OIS1N and CC1E bits.
Bit 1 CC1P: Capture/Compare 1 output polarity
CC1 channel configured as output:
0: OC1 active high
1: OC1 active low
CC1 channel configured as input:
The CC1NP/CC1P bits select the polarity of TI1FP1 and TI2FP1 for capture operation.
00: Non-inverted/rising edge: circuit is sensitive to TIxFP1's rising edge TIxFP1 is not
inverted.
01: Inverted/falling edge: circuit is sensitive to TIxFP1's falling edge, TIxFP1 is inverted.
10: Reserved, do not use this configuration.
11: Non-inverted/both edges: circuit is sensitive to both the rising and falling edges of
TIxFP1, TIxFP1 is not inverted.
Note: This bit is not writable as soon as LOCK level 2 or 3 has been programmed (LOCK bits
in TIMx_BDTR register)
Bit 0 CC1E: Capture/Compare 1 output enable
CC1 channel configured as output:
0: Off - OC1 is not active. OC1 level is then function of MOE, OSSI, OSSR, OIS1, OIS1N
and CC1NE bits.
1: On - OC1 signal is output on the corresponding output pin depending on MOE, OSSI,
OSSR, OIS1, OIS1N and CC1NE bits.
CC1 channel configured as input:
This bit determines if a capture of the counter value can actually be done into the input
capture/compare register 1 (TIMx_CCR1) or not.
0: Capture disabled
1: Capture enabled
448/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Table 82. Output control bits for complementary OCx and OCxN channels with break
feature
Output states(1)
Control bits
MOE OSSI OSSR CCxE CCxNE
OCx output state
bit
bit
bit
bit
bit
1
0
OCxN output state
0
0
0
Output Disabled (not
driven by the timer)
OCx=0, OCx_EN=0
Output Disabled (not driven by
the timer)
OCxN=0, OCxN_EN=0
0
0
1
Output Disabled (not
driven by the timer)
OCx=0, OCx_EN=0
OCxREF + Polarity
OCxN=OCxREF xor CCxNP,
OCxN_EN=1
Output Disabled (not driven by
the timer)
OCxN=0, OCxN_EN=0
0
1
0
OCxREF + Polarity
OCx=OCxREF xor CCxP,
OCx_EN=1
0
1
1
OCREF + Polarity + deadtime
OCx_EN=1
Complementary to OCREF (not
OCREF) + Polarity + dead-time
OCxN_EN=1
1
0
0
Output Disabled (not
driven by the timer)
OCx=CCxP, OCx_EN=0
Output Disabled (not driven by
the timer)
OCxN=CCxNP, OCxN_EN=0
1
0
1
Off-State (output enabled
with inactive state)
OCx=CCxP, OCx_EN=1
OCxREF + Polarity
OCxN=OCxREF xor CCxNP,
OCxN_EN=1
1
1
0
OCxREF + Polarity
OCx=OCxREF xor CCxP,
OCx_EN=1
Off-State (output enabled with
inactive state)
OCxN=CCxNP, OCxN_EN=1
1
1
1
OCREF + Polarity + deadtime
OCx_EN=1
Complementary to OCREF (not
OCREF) + Polarity + dead-time
OCxN_EN=1
0
0
0
0
0
1
0
1
0
0
1
1
0
0
1
0
1
1
1
0
1
1
1
X
1
X
Output Disabled (not driven by the timer)
Asynchronously: OCx=CCxP, OCx_EN=0, OCxN=CCxNP,
OCxN_EN=0
Then if the clock is present: OCx=OISx and OCxN=OISxN
after a dead-time, assuming that OISx and OISxN do not
correspond to OCX and OCxN both in active state.
Off-State (output enabled with inactive state)
Asynchronously: OCx=CCxP, OCx_EN=1, OCxN=CCxNP,
OCxN_EN=1
Then if the clock is present: OCx=OISx and OCxN=OISxN
after a dead-time, assuming that OISx and OISxN do not
correspond to OCX and OCxN both in active state
1. When both outputs of a channel are not used (CCxE = CCxNE = 0), the OISx, OISxN, CCxP and CCxNP
bits must be kept cleared.
Note:
The state of the external I/O pins connected to the complementary OCx and OCxN channels
depends on the OCx and OCxN channel state and the GPIO and AFIO registers.
Doc ID16188 Rev 5
449/713
457
General-purpose timers (TIM15/16/17)
15.6.8
RM0041
TIM16&TIM17 counter (TIMx_CNT)
Address offset: 0x24
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CNT[15:0]
rw
rw
rw
Bits 15:0
15.6.9
rw
rw
rw
rw
rw
rw
CNT[15:0]: Counter value
TIM16&TIM17 prescaler (TIMx_PSC)
Address offset: 0x28
Reset value: 0x0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
7
PSC[15:0]
rw
Bits 15:0 PSC[15:0]: Prescaler value
The counter clock frequency (CK_CNT) is equal to fCK_PSC / (PSC[15:0] + 1).
PSC contains the value to be loaded in the active prescaler register at each update event
(including when the counter is cleared through UG bit of TIMx_EGR register or through trigger
controller when configured in “reset mode”).
15.6.10
TIM16&TIM17 auto-reload register (TIMx_ARR)
Address offset: 0x2C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
ARR[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 ARR[15:0]: Auto-reload value
ARR is the value to be loaded in the actual auto-reload register.
Refer to the Section 14.3.1: Time-base unit on page 343 for more details about ARR update
and behavior.
The counter is blocked while the auto-reload value is null.
450/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
15.6.11
TIM16&TIM17 repetition counter register (TIMx_RCR)
Address offset: 0x30
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
REP[7:0]
Reserved
rw
rw
rw
rw
rw
Bits 15:8 Reserved, must be kept at reset value.
Bits 7:0 REP[7:0]: Repetition counter value
These bits allow the user to set-up the update rate of the compare registers (i.e. periodic
transfers from preload to active registers) when preload registers are enable, as well as the
update interrupt generation rate, if this interrupt is enable.
Each time the REP_CNT related downcounter reaches zero, an update event is generated
and it restarts counting from REP value. As REP_CNT is reloaded with REP value only at the
repetition update event U_RC, any write to the TIMx_RCR register is not taken in account until
the next repetition update event.
It means in PWM mode (REP+1) corresponds to the number of PWM periods in edge-aligned
mode.
15.6.12
TIM16&TIM17 capture/compare register 1 (TIMx_CCR1)
Address offset: 0x34
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CCR1[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 CCR1[15:0]: Capture/Compare 1 value
If channel CC1 is configured as output:
CCR1 is the value to be loaded in the actual capture/compare 1 register (preload value).
It is loaded permanently if the preload feature is not selected in the TIMx_CCMR1 register (bit
OC1PE). Else the preload value is copied in the active capture/compare 1 register when an
update event occurs.
The active capture/compare register contains the value to be compared to the counter
TIMx_CNT and signaled on OC1 output.
If channel CC1 is configured as input:
CCR1 is the counter value transferred by the last input capture 1 event (IC1).
Doc ID16188 Rev 5
451/713
457
General-purpose timers (TIM15/16/17)
15.6.13
RM0041
TIM16&TIM17 break and dead-time register (TIMx_BDTR)
Address offset: 0x44
Reset value: 0x0000
15
14
13
12
11
10
MOE
AOE
BKP
BKE
OSSR
OSSI
rw
rw
rw
rw
rw
rw
Note:
9
8
7
6
5
LOCK[1:0]
rw
rw
4
3
2
1
0
rw
rw
rw
DTG[7:0]
rw
rw
rw
rw
rw
As the bits AOE, BKP, BKE, OSSI, OSSR and DTG[7:0] can be write-locked depending on
the LOCK configuration, it can be necessary to configure all of them during the first write
access to the TIMx_BDTR register.
Bit 15 MOE: Main output enable
This bit is cleared asynchronously by hardware as soon as the break input is active. It is set
by software or automatically depending on the AOE bit. It is acting only on the channels
which are configured in output.
0: OC and OCN outputs are disabled or forced to idle state
1: OC and OCN outputs are enabled if their respective enable bits are set (CCxE, CCxNE in
TIMx_CCER register)
See OC/OCN enable description for more details (Section 15.5.8: TIM15 capture/compare
enable register (TIM15_CCER) on page 427).
Bit 14 AOE: Automatic output enable
0: MOE can be set only by software
1: MOE can be set by software or automatically at the next update event (if the break input is
not be active)
Note: This bit can not be modified as long as LOCK level 1 has been programmed (LOCK bits
in TIMx_BDTR register).
Bit 13 BKP: Break polarity
0: Break input BRK is active low
1: Break input BRK is active high
Note: This bit can not be modified as long as LOCK level 1 has been programmed (LOCK bits
in TIMx_BDTR register).
Note: Any write operation to this bit takes a delay of 1 APB clock cycle to become effective.
Bit 12 BKE: Break enable
0: Break inputs (BRK and CSS clock failure event) disabled
1; Break inputs (BRK and CSS clock failure event) enabled
Note: This bit cannot be modified when LOCK level 1 has been programmed (LOCK bits in
TIMx_BDTR register).
Note: Any write operation to this bit takes a delay of 1 APB clock cycle to become effective.
Bit 11 OSSR: Off-state selection for Run mode
This bit is used when MOE=1 on channels having a complementary output which are
configured as outputs. OSSR is not implemented if no complementary output is implemented
in the timer.
See OC/OCN enable description for more details (Section 15.5.8: TIM15 capture/compare
enable register (TIM15_CCER) on page 427).
0: When inactive, OC/OCN outputs are disabled (OC/OCN enable output signal=0)
1: When inactive, OC/OCN outputs are enabled with their inactive level as soon as CCxE=1
or CCxNE=1. Then, OC/OCN enable output signal=1
Note: This bit can not be modified as soon as the LOCK level 2 has been programmed (LOCK
bits in TIMx_BDTR register).
452/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
Bit 10 OSSI: Off-state selection for Idle mode
This bit is used when MOE=0 on channels configured as outputs.
See OC/OCN enable description for more details (Section 15.5.8: TIM15 capture/compare
enable register (TIM15_CCER) on page 427).
0: When inactive, OC/OCN outputs are disabled (OC/OCN enable output signal=0)
1: When inactive, OC/OCN outputs are forced first with their idle level as soon as CCxE=1 or
CCxNE=1. OC/OCN enable output signal=1)
Note: This bit can not be modified as soon as the LOCK level 2 has been programmed (LOCK
bits in TIMx_BDTR register).
Bits 9:8 LOCK[1:0]: Lock configuration
These bits offer a write protection against software errors.
00: LOCK OFF - No bit is write protected
01: LOCK Level 1 = DTG bits in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2
register and BKE/BKP/AOE bits in TIMx_BDTR register can no longer be written.
10: LOCK Level 2 = LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER
register, as long as the related channel is configured in output through the CCxS bits) as well
as OSSR and OSSI bits can no longer be written.
11: LOCK Level 3 = LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in
TIMx_CCMRx registers, as long as the related channel is configured in output through the
CCxS bits) can no longer be written.
Note: The LOCK bits can be written only once after the reset. Once the TIMx_BDTR register
has been written, their content is frozen until the next reset.
Bits 7:0 DTG[7:0]: Dead-time generator setup
This bit-field defines the duration of the dead-time inserted between the complementary
outputs. DT correspond to this duration.
DTG[7:5]=0xx => DT=DTG[7:0]x tdtg with tdtg=tDTS
DTG[7:5]=10x => DT=(64+DTG[5:0])xtdtg with Tdtg=2xtDTS
DTG[7:5]=110 => DT=(32+DTG[4:0])xtdtg with Tdtg=8xtDTS
DTG[7:5]=111 => DT=(32+DTG[4:0])xtdtg with Tdtg=16xtDTS
Example if TDTS=125ns (8MHz), dead-time possible values are:
0 to 15875 ns by 125 ns steps,
16 µs to 31750 ns by 250 ns steps,
32 µs to 63 µs by 1 µs steps,
64 µs to 126 µs by 2 µs steps
Note: This bit-field can not be modified as long as LOCK level 1, 2 or 3 has been programmed
(LOCK bits in TIMx_BDTR register).
15.6.14
TIM16&TIM17 DMA control register (TIMx_DCR)
Address offset: 0x48
Reset value: 0x0000
15
14
Reserved
13
12
11
10
9
8
DBL[4:0]
rw
rw
rw
rw
rw
7
6
Reserved
Doc ID16188 Rev 5
5
4
3
2
1
0
rw
rw
DBA[4:0]
rw
rw
rw
453/713
457
General-purpose timers (TIM15/16/17)
RM0041
Bits 15:13 Reserved, must be kept at reset value.
Bits 12:8 DBL[4:0]: DMA burst length
This 5-bit vector defines the length of DMA transfers (the timer recognizes a burst transfer
when a read or a write access is done to the TIMx_DMAR address), i.e. the number of
transfers. Transfers can be in half-words or in bytes (see example below).
00000: 1 transfer,
00001: 2 transfers,
00010: 3 transfers,
...
10001: 18 transfers.
Bits 7:5 Reserved, must be kept at reset value.
Bits 4:0 DBA[4:0]: DMA base address
This 5-bits vector defines the base-address for DMA transfers (when read/write access are
done through the TIMx_DMAR address). DBA is defined as an offset starting from the
address of the TIMx_CR1 register.
Example:
00000: TIMx_CR1,
00001: TIMx_CR2,
00010: TIMx_SMCR,
...
Example: Let us consider the following transfer: DBL = 7 transfers and DBA = TIMx_CR1. In
this case the transfer is done to/from 7 registers starting from the TIMx_CR1 address..
15.6.15
TIM16&TIM17 DMA address for full transfer (TIMx_DMAR)
Address offset: 0x4C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
DMAB[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 DMAB[15:0]: DMA register for burst accesses
A read or write access to the DMAR register accesses the register located at the address:
“(TIMx_CR1 address) + DBA + (DMA index)” in which:
TIMx_CR1 address is the address of the control register 1, DBA is the DMA base address
configured in TIMx_DCR register, DMA index is the offset automatically controlled by the
DMA transfer, depending on the length of the transfer DBL in the TIMx_DCR register.
Example of how to use the DMA burst feature
In this example the timer DMA burst feature is used to update the contents of the CCRx
registers (x = 2, 3, 4) with the DMA transferring half words into the CCRx registers.
This is done in the following steps:
454/713
Doc ID16188 Rev 5
RM0041
General-purpose timers (TIM15/16/17)
1.
Note:
Configure the corresponding DMA channel as follows:
–
DMA channel peripheral address is the DMAR register address
–
DMA channel memory address is the address of the buffer in the RAM containing
the data to be transferred by DMA into CCRx registers.
–
Number of data to transfer = 3 (See note below).
–
Circular mode disabled.
2.
Configure the DCR register by configuring the DBA and DBL bit fields as follows:
DBL = 3 transfers, DBA = 0xE.
3.
Enable the TIMx update DMA request (set the UDE bit in the DIER register).
4.
Enable TIMx
5.
Enable the DMA channel
This example is for the case where every CCRx register to be updated once. If every CCRx
register is to be updated twice for example, the number of data to transfer should be 6. Let's
take the example of a buffer in the RAM containing data1, data2, data3, data4, data5 and
data6. The data is transferred to the CCRx registers as follows: on the first update DMA
request, data1 is transferred to CCR2, data2 is transferred to CCR3, data3 is transferred to
CCR4 and on the second update DMA request, data4 is transferred to CCR2, data5 is
transferred to CCR3 and data6 is transferred to CCR4.
Doc ID16188 Rev 5
455/713
457
General-purpose timers (TIM15/16/17)
15.6.16
RM0041
TIM16&TIM17 register map
TIM16&TIM17 registers are mapped as 16-bit addressable registers as described in the
table below:
0x18
0
0
OC1M
[2:0]
Reserved
Reset value
0
TIMx_CCMR1
Input Capture
mode
Reserved
0
TIMx_CCER
0
0
IC1F[3:0]
Reset value
0x20
0
0
0
0
Reserved
Reset value
0x24
TIMx_CNT
0x28
TIMx_PSC
0
0x2C
TIMx_ARR
0
0
0
0
0
0
0
0
0
0
0
OPM
URS
UDIS
CEN
CCUS
Reserved
CCPC
CC1IE
UIE
0
0
CC1
S
[1:0]
0
0
0
0
IC1
PSC
[1:0]
CC1
S
[1:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ARR[15:0]
Reserved
0
Doc ID16188 Rev 5
0
PSC[15:0]
0
Reset value
456/713
0
Reserved
Reset value
0
CNT[15:0]
Reserved
Reset value
CCDS
Reserved
UIF
Reset value
TIMx_CCMR1
Output
Compare mode
0
0
UG
Reserved
0
Reserved
0
CC1E
TIMx_EGR
Reserved
0
CC1IF
0
0
CC1G
0
0
CC1P
0
0
OC1FE
ARPE
TI1S
0
0
OC1PE
Reset value
0x14
0
0
0
CC1NE
Reserved
0
0
CC1NP
TIMx_SR
0
COMG
0x10
0
0
CC1OF
Reset value
Reserved
0
TIE
Reserved
0
TIF
TIMx_DIER
MMS[2:0]
TG
0x0C
TDE
Reset value
Reserved
OIS1
Reserved
0
BIE
TIMx_CR2
0
BIF
0x04
0
BG
Reset value
CKD
[1:0]
OIS1N
Reserved
UDE
TIMx_CR1
CC1DE
0x00
Register
Reserved
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 83. TIM16&TIM17 register map and reset values
0
0
0
0
0
0
0
0
RM0041
General-purpose timers (TIM15/16/17)
Offset
0x30
Register
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 83. TIM16&TIM17 register map and reset values (continued)
TIMx_RCR
REP[7:0]
Reserved
Reset value
Reset value
0x48
TIMx_DCR
TIMx_DMAR
0
0
0
LOCK
[1:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DT[7:0]
0
0
0
0
DBA[4:0]
Reserved
0
0
0
0
0
0
0
0
0
0
0
0
DMAB[15:0]
Reserved
Reset value
0
DBL[4:0]
Reserved
Reset value
0x4C
0
OSSI
Reserved
0
BKE
TIMx_BDTR
0
OSSR
0x44
0
BKP
Reset value
0
CCR1[15:0]
Reserved
AOE
TIMx_CCR1
MOE
0x34
0
0
0
0
0
0
0
0
0
0
0
0
Refer to Section: Memory map for the register boundary addresses.
Doc ID16188 Rev 5
457/713
457
Basic timers (TIM6 and TIM7)
16
RM0041
Basic timers (TIM6 and TIM7)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
16.1
TIM6&TIM7 introduction
The basic timers TIM6 and TIM7 consist of a 16-bit auto-reload counter driven by a
programmable prescaler.
They may be used as generic timers for time-base generation but they are also specifically
used to drive the digital-to-analog converter (DAC). In fact, the timers are internally
connected to the DAC and are able to drive it through their trigger outputs.
The timers are completely independent, and do not share any resources.
16.2
TIM6&TIM7 main features
Basic timer (TIM6&TIM7) features include:
458/713
•
16-bit auto-reload upcounter
•
16-bit programmable prescaler used to divide (also “on the fly”) the counter clock
frequency by any factor between 1 and 65536
•
Synchronization circuit to trigger the DAC
•
Interrupt/DMA generation on the update event: counter overflow
Doc ID16188 Rev 5
RM0041
Basic timers (TIM6 and TIM7)
Figure 186. Basic timer block diagram
TIMxCLK from RCC
Trigger TRGO
controller
Internal clock (CK_INT)
Reset, Enable, Count,
Controller
U
Auto-reload Register
Stop, Clear or up
CK_PSC
Flag
CK_CNT
PSC
±
Prescaler
to DAC
UI
U
CNT
COUNTER
Preload registers transferred
to active registers on U event according to control bit
event
interrupt & DMA output
ai14749b
16.3
TIM6&TIM7 functional description
16.3.1
Time-base unit
The main block of the programmable timer is a 16-bit upcounter with its related auto-reload
register. The counter clock can be divided by a prescaler.
The counter, the auto-reload register and the prescaler register can be written or read by
software. This is true even when the counter is running.
The time-base unit includes:
•
Counter Register (TIMx_CNT)
•
Prescaler Register (TIMx_PSC)
•
Auto-Reload Register (TIMx_ARR)
The auto-reload register is preloaded. The preload register is accessed each time an
attempt is made to write or read the auto-reload register. The contents of the preload
register are transferred into the shadow register permanently or at each update event UEV,
depending on the auto-reload preload enable bit (ARPE) in the TIMx_CR1 register. The
update event is sent when the counter reaches the overflow value and if the UDIS bit equals
0 in the TIMx_CR1 register. It can also be generated by software. The generation of the
update event is described in detail for each configuration.
The counter is clocked by the prescaler output CK_CNT, which is enabled only when the
counter enable bit (CEN) in the TIMx_CR1 register is set.
Note that the actual counter enable signal CNT_EN is set 1 clock cycle after CEN.
Doc ID16188 Rev 5
459/713
470
Basic timers (TIM6 and TIM7)
RM0041
Prescaler description
The prescaler can divide the counter clock frequency by any factor between 1 and 65536. It
is based on a 16-bit counter controlled through a 16-bit register (in the TIMx_PSC register).
It can be changed on the fly as the TIMx_PSC control register is buffered. The new
prescaler ratio is taken into account at the next update event.
Figure 187 and Figure 188 give some examples of the counter behavior when the prescaler
ratio is changed on the fly.
Figure 187. Counter timing diagram with prescaler division change from 1 to 2
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
)
)
)$ )% )&
8SGDWHHYHQW8(9
3UHVFDOHUFRQWUROUHJLVWHU
:ULWHDQHZYDOXHLQ7,0[B36&
3UHVFDOHUEXIIHU
3UHVFDOHUFRXQWHU
069
460/713
Doc ID16188 Rev 5
RM0041
Basic timers (TIM6 and TIM7)
Figure 188. Counter timing diagram with prescaler division change from 1 to 4
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
)
)
)$ )% )&
8SGDWHHYHQW8(9
3UHVFDOHUFRQWUROUHJLVWHU
:ULWHDQHZYDOXHLQ7,0[B36&
3UHVFDOHUEXIIHU
3UHVFDOHUFRXQWHU
069
16.3.2
Counting mode
The counter counts from 0 to the auto-reload value (contents of the TIMx_ARR register),
then restarts from 0 and generates a counter overflow event.
An update event can be generate at each counter overflow or by setting the UG bit in the
TIMx_EGR register (by software or by using the slave mode controller).
The UEV event can be disabled by software by setting the UDIS bit in the TIMx_CR1
register. This avoids updating the shadow registers while writing new values into the preload
registers. In this way, no update event occurs until the UDIS bit has been written to 0,
however, the counter and the prescaler counter both restart from 0 (but the prescale rate
does not change). In addition, if the URS (update request selection) bit in the TIMx_CR1
register is set, setting the UG bit generates an update event UEV, but the UIF flag is not set
(so no interrupt or DMA request is sent).
When an update event occurs, all the registers are updated and the update flag (UIF bit in
the TIMx_SR register) is set (depending on the URS bit):
•
The buffer of the prescaler is reloaded with the preload value (contents of the
TIMx_PSC register)
•
The auto-reload shadow register is updated with the preload value (TIMx_ARR)
The following figures show some examples of the counter behavior for different clock
frequencies when TIMx_ARR = 0x36.
Doc ID16188 Rev 5
461/713
470
Basic timers (TIM6 and TIM7)
RM0041
Figure 189. Counter timing diagram, internal clock divided by 1
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
Figure 190. Counter timing diagram, internal clock divided by 2
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
069
462/713
Doc ID16188 Rev 5
RM0041
Basic timers (TIM6 and TIM7)
Figure 191. Counter timing diagram, internal clock divided by 4
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
06Y9
Figure 192. Counter timing diagram, internal clock divided by N
&.B,17
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
06Y9
Figure 193. Counter timing diagram, update event when ARPE=0 (TIMx_ARR not
preloaded)
&.B,17
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
&RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGUHJLVWHU
))
:ULWHDQHZYDOXHLQ7,0[B$55
06Y9
Doc ID16188 Rev 5
463/713
470
Basic timers (TIM6 and TIM7)
RM0041
Figure 194. Counter timing diagram, update event when ARPE=1 (TIMx_ARR
preloaded)
&.B36&
&17B(1
7LPHUFORFN &.B&17
&RXQWHUUHJLVWHU
)
) ) ) ) ) &RXQWHURYHUIORZ
8SGDWHHYHQW8(9
8SGDWHLQWHUUXSWIODJ8,)
$XWRUHORDGSUHORDGUHJLVWHU
)
$XWRUHORDGVKDGRZUHJLVWHU
)
:ULWHDQHZYDOXHLQ7,0[B$55
06Y9
16.3.3
Clock source
The counter clock is provided by the Internal clock (CK_INT) source.
The CEN (in the TIMx_CR1 register) and UG bits (in the TIMx_EGR register) are actual
control bits and can be changed only by software (except for UG that remains cleared
automatically). As soon as the CEN bit is written to 1, the prescaler is clocked by the internal
clock CK_INT.
Figure 195 shows the behavior of the control circuit and the upcounter in normal mode,
without prescaler.
Figure 195. Control circuit in normal mode, internal clock divided by 1
,QWHUQDOFORFN
&(1 &17B(1
8*
&17B,1,7
&RXQWHUFORFN &.B&17 &.B36&
&RXQWHUUHJLVWHU
069
464/713
Doc ID16188 Rev 5
RM0041
Basic timers (TIM6 and TIM7)
16.3.4
Debug mode
When the microcontroller enters the debug mode (Cortex®-M3 core - halted), the TIMx
counter either continues to work normally or stops, depending on the DBG_TIMx_STOP
configuration bit in the DBG module. For more details, refer to Section 25.15.2: Debug
support for timers, watchdog and I2C.
16.4
TIM6&TIM7 registers
Refer to Section: List of abbreviations for registers for a list of abbreviations used in register
descriptions.
The peripheral registers have to be written by half-words (16 bits) or words (32 bits). Read
accesses can be done by bytes (8 bits), half-words (16 bits) or words (32 bits).
16.4.1
TIM6&TIM7 control register 1 (TIMx_CR1)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
11
Reserved
10
9
8
7
6
ARPE
rw
5
Reserved
4
3
2
1
0
OPM
URS
UDIS
CEN
rw
rw
rw
rw
Bits 15:8 Reserved, must be kept at reset value.
Bit 7 ARPE: Auto-reload preload enable
0: TIMx_ARR register is not buffered.
1: TIMx_ARR register is buffered.
Bits 6:4 Reserved, must be kept at reset value.
Bit 3 OPM: One-pulse mode
0: Counter is not stopped at update event
1: Counter stops counting at the next update event (clearing the CEN bit).
Doc ID16188 Rev 5
465/713
470
Basic timers (TIM6 and TIM7)
RM0041
Bit 2 URS: Update request source
This bit is set and cleared by software to select the UEV event sources.
0: Any of the following events generates an update interrupt or DMA request if enabled.
These events can be:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
1: Only counter overflow/underflow generates an update interrupt or DMA request if enabled.
Bit 1 UDIS: Update disable
This bit is set and cleared by software to enable/disable UEV event generation.
0: UEV enabled. The Update (UEV) event is generated by one of the following events:
–
Counter overflow/underflow
–
Setting the UG bit
–
Update generation through the slave mode controller
Buffered registers are then loaded with their preload values.
1: UEV disabled. The Update event is not generated, shadow registers keep their value
(ARR, PSC). However the counter and the prescaler are reinitialized if the UG bit is set or if
a hardware reset is received from the slave mode controller.
Bit 0 CEN: Counter enable
0: Counter disabled
1: Counter enabled
Note: Gated mode can work only if the CEN bit has been previously set by software. However
trigger mode can set the CEN bit automatically by hardware.
CEN is cleared automatically in one-pulse mode, when an update event occurs.
466/713
Doc ID16188 Rev 5
RM0041
Basic timers (TIM6 and TIM7)
16.4.2
TIM6&TIM7 control register 2 (TIMx_CR2)
Address offset: 0x04
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
MMS[2:0]
Reserved
rw
rw
2
1
0
Reserved
rw
Bits 15:7 Reserved, must be kept at reset value.
Bits 6:4 MMS[2:0]: Master mode selection
These bits are used to select the information to be sent in master mode to slave timers for
synchronization (TRGO). The combination is as follows:
000: Reset - the UG bit from the TIMx_EGR register is used as a trigger output (TRGO). If
reset is generated by the trigger input (slave mode controller configured in reset mode) then
the signal on TRGO is delayed compared to the actual reset.
001: Enable - the Counter enable signal, CNT_EN, is used as a trigger output (TRGO). It is
useful to start several timers at the same time or to control a window in which a slave timer
is enabled. The Counter Enable signal is generated by a logic OR between CEN control bit
and the trigger input when configured in gated mode.
When the Counter Enable signal is controlled by the trigger input, there is a delay on TRGO,
except if the master/slave mode is selected (see the MSM bit description in the TIMx_SMCR
register).
010: Update - The update event is selected as a trigger output (TRGO). For instance a
master timer can then be used as a prescaler for a slave timer.
Note: The clock of the slave timer and ADC must be enabled prior to receiving events from
the master timer, and must not be changed on-the-fly while triggers are received from
the master timer.
Bits 3:0 Reserved, must be kept at reset value.
16.4.3
TIM6&TIM7 DMA/Interrupt enable register (TIMx_DIER)
Address offset: 0x0C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
UDE
Reserved
rw
6
5
4
Reserved
3
2
1
0
UIE
rw
Bits 15:9 Reserved, must be kept at reset value.
Bit 8 UDE: Update DMA request enable
0: Update DMA request disabled.
1: Update DMA request enabled.
Bits 7:1 Reserved, must be kept at reset value.
Bit 0 UIE: Update interrupt enable
0: Update interrupt disabled.
1: Update interrupt enabled.
Doc ID16188 Rev 5
467/713
470
Basic timers (TIM6 and TIM7)
16.4.4
RM0041
TIM6&TIM7 status register (TIMx_SR)
Address offset: 0x10
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
UIF
Reserved
rc_w0
Bits 15:1 Reserved, must be kept at reset value.
Bit 0 UIF: Update interrupt flag
This bit is set by hardware on an update event. It is cleared by software.
0: No update occurred.
1: Update interrupt pending. This bit is set by hardware when the registers are updated:
– At overflow or underflow and if UDIS = 0 in the TIMx_CR1 register.
– When CNT is reinitialized by software using the UG bit in the TIMx_EGR register, if URS = 0
and UDIS = 0 in the TIMx_CR1 register.
16.4.5
TIM6&TIM7 event generation register (TIMx_EGR)
Address offset: 0x14
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
UG
Reserved
w
Bits 15:1 Reserved, must be kept at reset value.
Bit 0 UG: Update generation
This bit can be set by software, it is automatically cleared by hardware.
0: No action.
1: Re-initializes the timer counter and generates an update of the registers. Note that the
prescaler counter is cleared too (but the prescaler ratio is not affected).
16.4.6
TIM6&TIM7 counter (TIMx_CNT)
Address offset: 0x24
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
CNT[15:0]
rw
rw
Bits 15:0
468/713
rw
rw
rw
rw
rw
rw
rw
CNT[15:0]: Counter value
Doc ID16188 Rev 5
RM0041
Basic timers (TIM6 and TIM7)
16.4.7
TIM6&TIM7 prescaler (TIMx_PSC)
Address offset: 0x28
Reset value: 0x0000
15
14
13
12
11
10
9
8
rw
rw
rw
rw
rw
rw
rw
rw
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
PSC[15:0]
rw
Bits 15:0 PSC[15:0]: Prescaler value
The counter clock frequency CK_CNT is equal to fCK_PSC / (PSC[15:0] + 1).
PSC contains the value to be loaded in the active prescaler register at each update event
(including when the counter is cleared through UG bit of TIMx_EGR register or through
trigger controller when configured in “reset mode”).
16.4.8
TIM6&TIM7 auto-reload register (TIMx_ARR)
Address offset: 0x2C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
ARR[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 ARR[15:0]: Auto-reload value
ARR is the value to be loaded into the actual auto-reload register.
Refer to Section 16.3.1: Time-base unit for more details about ARR update and behavior.
The counter is blocked while the auto-reload value is null.
Doc ID16188 Rev 5
469/713
470
Basic timers (TIM6 and TIM7)
16.4.9
RM0041
TIM6&TIM7 register map
TIMx registers are mapped as 16-bit addressable registers as described in the table below:
TIMx_CR2
MMS[2:0]
Reserved
Reset value
0
URS
UDIS
CEN
0
0
0
Reserved
UDE
TIMx_DIER
Reserved
0
TIMx_SR
0
UIF
Reset value
0x10
0
0
Reserved
0x08
0x0C
0
UIE
0x04
0
Reserved
Reserved
Reset value
OPM
TIMx_CR1
Reserved
0x00
Register
ARPE
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 84. TIM6&TIM7 register map and reset values
Reserved
0x14
0
TIMx_EGR
UG
Reset value
Reserved
Reset value
0
0x18
Reserved
0x1C
Reserved
0x20
Reserved
0x24
TIMx_CNT
Reset value
0x28
TIMx_PSC
0
TIMx_ARR
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Refer to Section: Memory map for the register boundary addresses.
470/713
Doc ID16188 Rev 5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ARR[15:0]
Reserved
Reset value
0
PSC[15:0]
Reserved
Reset value
0x2C
CNT[15:0]
Reserved
0
0
0
RM0041
17
Real-time clock (RTC)
Real-time clock (RTC)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F10xxx family, unless otherwise specified.
17.1
RTC introduction
The real-time clock is an independent timer. The RTC provides a set of continuously running
counters which can be used, with suitable software, to provide a clock-calendar function.
The counter values can be written to set the current time/date of the system.
The RTC core and clock configuration (RCC_BDCR register) are in the Backup domain,
which means that RTC setting and time are kept after reset or wakeup from Standby mode.
After reset, access to the Backup registers and RTC is disabled and the Backup domain
(BKP) is protected against possible parasitic write access. To enable access to the Backup
registers and the RTC, proceed as follows:
•
enable the power and backup interface clocks by setting the PWREN and BKPEN bits
in the RCC_APB1ENR register
•
set the DBP bit the Power Control Register (PWR_CR) to enable access to the Backup
registers and RTC.
Doc ID16188 Rev 5
471/713
482
Real-time clock (RTC)
17.2
RTC main features
•
Programmable prescaler: division factor up to 220
•
32-bit programmable counter for long-term measurement
•
Two separate clocks: PCLK1 for the APB1 interface and RTC clock (must be at least
four times slower than the PCLK1 clock)
•
The RTC clock source could be any of the following ones:
•
•
472/713
RM0041
–
HSE clock divided by 128
–
LSE oscillator clock
–
LSI oscillator clock (refer to Section 6.2.8: RTC clock for details)
Two separate reset types:
–
The APB1 interface is reset by system reset
–
The RTC Core (Prescaler, Alarm, Counter and Divider) is reset only by a Backup
domain reset (see Section 6.1.3: Backup domain reset on page 70).
Three dedicated maskable interrupt lines:
–
Alarm interrupt, for generating a software programmable alarm interrupt.
–
Seconds interrupt, for generating a periodic interrupt signal with a programmable
period length (up to 1 second).
–
Overflow interrupt, to detect when the internal programmable counter rolls over to
zero.
Doc ID16188 Rev 5
RM0041
Real-time clock (RTC)
17.3
RTC functional description
17.3.1
Overview
The RTC consists of two main units (see Figure 196). The first one (APB1 Interface) is used
to interface with the APB1 bus. This unit also contains a set of 16-bit registers accessible
from the APB1 bus in read or write mode (for more information refer to Section 17.4: RTC
registers). The APB1 interface is clocked by the APB1 bus clock in order to interface with
the APB1 bus.
The other unit (RTC Core) consists of a chain of programmable counters made of two main
blocks. The first block is the RTC prescaler block, which generates the RTC time base
TR_CLK that can be programmed to have a period of up to 1 second. It includes a 20-bit
programmable divider (RTC Prescaler). Every TR_CLK period, the RTC generates an
interrupt (Second Interrupt) if it is enabled in the RTC_CR register. The second block is a
32-bit programmable counter that can be initialized to the current system time. The system
time is incremented at the TR_CLK rate and compared with a programmable date (stored in
the RTC_ALR register) in order to generate an alarm interrupt, if enabled in the RTC_CR
control register.
Figure 196. RTC simplified block diagram
APB1 bus
PCLK1
APB1 interface
RTCCLK
not powered in Standby
Backup domain
RTC_CR
RTC_PRL
RTC_Second
Reload
RTC_DIV
TR_CLK
32-bit programmable
counter
SECIE
RTC_Overflow
RTC_CNT
OWF
rising
edge
RTC prescaler
SECF
OWIE
RTC_Alarm
=
ALRF
ALRIE
RTC_ALR
not powered in Standby
powered in Standby
NVIC interrupt
controller
powered in Standby
not powered in Standby
WKUP pin
RTC_Alarm
WKP_STDBY
exit
Standby mode
powered in Standby
ai14969b
Doc ID16188 Rev 5
473/713
482
Real-time clock (RTC)
17.3.2
RM0041
Resetting RTC registers
All system registers are asynchronously reset by a System Reset or Power Reset, except
for RTC_PRL, RTC_ALR, RTC_CNT, and RTC_DIV.
The RTC_PRL, RTC_ALR, RTC_CNT, and RTC_DIV registers are reset only by a Backup
Domain reset. Refer to Section 6.1.3: Backup domain reset.
17.3.3
Reading RTC registers
The RTC core is completely independent from the RTC APB1 interface.
Software accesses the RTC prescaler, counter and alarm values through the APB1
interface but the associated readable registers are internally updated at each rising edge of
the RTC clock resynchronized by the RTC APB1 clock. This is also true for the RTC flags.
This means that the first read to the RTC APB1 registers may be corrupted (generally read
as 0) if the APB1 interface has previously been disabled and the read occurs immediately
after the APB1 interface is enabled but before the first internal update of the registers. This
can occur if:
•
A system reset or power reset has occurred
•
The MCU has just woken up from Standby mode (see Section 4.3: Low-power modes)
•
The MCU has just woken up from Stop mode (see Section 4.3: Low-power modes)
In all the above cases, the RTC core has been kept running while the APB1 interface was
disabled (reset, not clocked or unpowered).
Consequently when reading the RTC registers, after having disabled the RTC APB1
interface, the software must first wait for the RSF bit (Register Synchronized Flag) in the
RTC_CRL register to be set by hardware.
Note that the RTC APB1 interface is not affected by WFI and WFE low-power modes.
17.3.4
Configuring RTC registers
To write in the RTC_PRL, RTC_CNT, RTC_ALR registers, the peripheral must enter
Configuration Mode. This is done by setting the CNF bit in the RTC_CRL register.
In addition, writing to any RTC register is only enabled if the previous write operation is
finished. To enable the software to detect this situation, the RTOFF status bit is provided in
the RTC_CR register to indicate that an update of the registers is in progress. A new value
can be written to the RTC registers only when the RTOFF status bit value is ’1’.
Configuration procedure:
1.
Poll RTOFF, wait until its value goes to ‘1’
2.
Set the CNF bit to enter configuration mode
3.
Write to one or more RTC registers
4.
Clear the CNF bit to exit configuration mode
5.
Poll RTOFF, wait until its value goes to ‘1’ to check the end of the write operation.
The write operation only executes when the CNF bit is cleared; it takes at least three
RTCCLK cycles to complete.
474/713
Doc ID16188 Rev 5
RM0041
Real-time clock (RTC)
17.3.5
RTC flag assertion
The RTC Second flag (SECF) is asserted on each RTC Core clock cycle before the update
of the RTC Counter.
The RTC Overflow flag (OWF) is asserted on the last RTC Core clock cycle before the
counter reaches 0x0000.
The RTC_Alarm and RTC Alarm flag (ALRF) (see Figure 197) are asserted on the last RTC
Core clock cycle before the counter reaches the RTC Alarm value stored in the Alarm
register increased by one (RTC_ALR + 1). The write operation in the RTC Alarm and RTC
Second flag must be synchronized by using one of the following sequences:
•
Use the RTC Alarm interrupt and inside the RTC interrupt routine, the RTC Alarm
and/or RTC Counter registers are updated.
•
Wait for SECF bit to be set in the RTC Control register. Update the RTC Alarm and/or
the RTC Counter register.
Figure 197. RTC second and alarm waveform example with PR=0003, ALARM=00004
RTCCLK
RTC_PR
0002
0001
0000
0003
0002
0001
0000
0003
0002
0001
0000
0003
0002
0001
0000
0003
0002
0001
0000
0003
0002
0001
0000
0003
RTC_Second
RTC_CNT
0001
0000
0002
0003
0004
0005
RTC_ALARM
1 RTCCLK
ALRF
(not powered
in Standby)
can be cleared by software
Figure 198. RTC Overflow waveform example with PR=0003
RTCCLK
RTC_PR
0002
0001
0000
0003
0002
0001
0000
0003
0002
0001
0000
0003
0002
0001
0000
0003
0002
0001
0000
0003
0002
0001
0000
0003
RTC_Second
RTC_CNT
FFFFFFFB
FFFFFFFC
FFFFFFFD
FFFFFFFE
0000
FFFFFFFF
RTC_Overflow
1 RTCCLK
OWF
(not powered
in Standby)
can be cleared by software
Doc ID16188 Rev 5
475/713
482
Real-time clock (RTC)
17.4
RM0041
RTC registers
Refer to Section 1.1 on page 32 for a list of abbreviations used in register descriptions.
The peripheral registers can be accessed by half-words (16-bit) or words (32-bit).
17.4.1
RTC control register high (RTC_CRH)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
OWIE
ALRIE
SECIE
rw
rw
rw
Reserved
Bits 15:3 Reserved, forced by hardware to 0.
Bit 2 OWIE: Overflow interrupt enable
0: Overflow interrupt is masked.
1: Overflow interrupt is enabled.
Bit 1 ALRIE: Alarm interrupt enable
0: Alarm interrupt is masked.
1: Alarm interrupt is enabled.
Bit 0 SECIE: Second interrupt enable
0: Second interrupt is masked.
1: Second interrupt is enabled.
These bits are used to mask interrupt requests. Note that at reset all interrupts are disabled,
so it is possible to write to the RTC registers to ensure that no interrupt requests are pending
after initialization. It is not possible to write to the RTC_CRH register when the peripheral is
completing a previous write operation (flagged by RTOFF=0, see Section 17.3.4).
The RTC functions are controlled by this control register. Some bits must be written using a
specific configuration procedure (see Configuration procedure:).
476/713
Doc ID16188 Rev 5
RM0041
Real-time clock (RTC)
17.4.2
RTC control register low (RTC_CRL)
Address offset: 0x04
Reset value: 0x0020
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RTOFF
CNF
RSF
OWF
ALRF
SECF
r
rw
rc_w0
rc_w0
rc_w0
rc_w0
Reserved
Bits 15:6 Reserved, forced by hardware to 0.
Bit 5 RTOFF: RTC operation OFF
With this bit the RTC reports the status of the last write operation performed on its registers,
indicating if it has been completed or not. If its value is ‘0’ then it is not possible to write to any
of the RTC registers. This bit is read only.
0: Last write operation on RTC registers is still ongoing.
1: Last write operation on RTC registers terminated.
Bit 4 CNF: Configuration flag
This bit must be set by software to enter in configuration mode so as to allow new values to
be written in the RTC_CNT, RTC_ALR or RTC_PRL registers. The write operation is only
executed when the CNF bit is reset by software after has been set.
0: Exit configuration mode (start update of RTC registers).
1: Enter configuration mode.
Bit 3 RSF: Registers synchronized flag
This bit is set by hardware at each time the RTC_CNT and RTC_DIV registers are updated
and cleared by software. Before any read operation after an APB1 reset or an APB1 clock
stop, this bit must be cleared by software, and the user application must wait until it is set to
be sure that the RTC_CNT, RTC_ALR or RTC_PRL registers are synchronized.
0: Registers not yet synchronized.
1: Registers synchronized.
Bit 2 OWF: Overflow flag
This bit is set by hardware when the 32-bit programmable counter overflows. An interrupt is
generated if OWIE=1 in the RTC_CRH register. It can be cleared only by software. Writing ‘1’
has no effect.
0: Overflow not detected
1: 32-bit programmable counter overflow occurred.
Bit 1 ALRF: Alarm flag
This bit is set by hardware when the 32-bit programmable counter reaches the threshold set
in the RTC_ALR register. An interrupt is generated if ALRIE=1 in the RTC_CRH register. It
can be cleared only by software. Writing ‘1’ has no effect.
0: Alarm not detected
1: Alarm detected
Bit 0 SECF: Second flag
This bit is set by hardware when the 32-bit programmable prescaler overflows, thus
incrementing the RTC counter. Hence this flag provides a periodic signal with a period
corresponding to the resolution programmed for the RTC counter (usually one second). An
interrupt is generated if SECIE=1 in the RTC_CRH register. It can be cleared only by
software. Writing ‘1’ has no effect.
0: Second flag condition not met.
1: Second flag condition met.
Doc ID16188 Rev 5
477/713
482
Real-time clock (RTC)
RM0041
The functions of the RTC are controlled by this control register. It is not possible to write to
the RTC_CR register while the peripheral is completing a previous write operation (flagged
by RTOFF=0, see Section 17.3.4: Configuring RTC registers).
Note:
Any flag remains pending until the appropriate RTC_CR request bit is reset by software,
indicating that the interrupt request has been granted.
At reset the interrupts are disabled, no interrupt requests are pending and it is possible to
write to the RTC registers.
The OWF, ALRF, SECF and RSF bits are not updated when the APB1 clock is not running.
The OWF, ALRF, SECF and RSF bits can only be set by hardware and only cleared by
software.
If ALRF = 1 and ALRIE = 1, the RTC global interrupt is enabled. If EXTI Line 17 is also
enabled through the EXTI Controller, both the RTC global interrupt and the RTC Alarm
interrupt are enabled.
If ALRF = 1, the RTC Alarm interrupt is enabled if EXTI Line 17 is enabled through the EXTI
Controller in interrupt mode. When the EXTI Line 17 is enabled in event mode, a pulse is
generated on this line (no RTC Alarm interrupt generation).
17.4.3
RTC prescaler load register (RTC_PRLH / RTC_PRLL)
The Prescaler Load registers keep the period counting value of the RTC prescaler. They are
write-protected by the RTOFF bit in the RTC_CR register, and a write operation is allowed if
the RTOFF value is ‘1’.
RTC prescaler load register high (RTC_PRLH)
Address offset: 0x08
Write only (see Section 17.3.4: Configuring RTC registers)
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PRL[19:16]
Reserved
w
w
w
w
Bits 15:4 Reserved, forced by hardware to 0.
Bits 3:0 PRL[19:16]: RTC prescaler reload value high
These bits are used to define the counter clock frequency according to the following formula:
fTR_CLK = fRTCCLK/(PRL[19:0]+1)
478/713
Doc ID16188 Rev 5
RM0041
Real-time clock (RTC)
RTC prescaler load register low (RTC_PRLL)
Address offset: 0x0C
Write only (see Section 17.3.4: Configuring RTC registers)
Reset value: 0x8000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
w
w
w
w
w
w
w
PRL[15:0]
w
w
w
w
w
w
w
w
w
Bits 15:0 PRL[15:0]: RTC prescaler reload value low
These bits are used to define the counter clock frequency according to the following formula:
fTR_CLK = fRTCCLK/(PRL[19:0]+1)
Caution:
The zero value is not recommended. RTC interrupts and flags cannot be
asserted correctly.
Note:
If the input clock frequency (fRTCCLK) is 32.768 kHz, write 7FFFh in this register to get a
signal period of 1 second.
17.4.4
RTC prescaler divider register (RTC_DIVH / RTC_DIVL)
During each period of TR_CLK, the counter inside the RTC prescaler is reloaded with the
value stored in the RTC_PRL register. To get an accurate time measurement it is possible to
read the current value of the prescaler counter, stored in the RTC_DIV register, without
stopping it. This register is read-only and it is reloaded by hardware after any change in the
RTC_PRL or RTC_CNT registers.
RTC prescaler divider register high (RTC_DIVH)
Address offset: 0x10
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RTC_DIV[19:16]
Reserved
r
r
r
r
Bits 15:4 Reserved
Bits 3:0 RTC_DIV[19:16]: RTC clock divider high
RTC prescaler divider register low (RTC_DIVL)
Address offset: 0x14
Reset value: 0x8000
15
14
13
12
11
10
9
r
r
r
r
r
r
r
8
7
6
5
4
3
2
1
0
r
r
r
r
r
r
r
RTC_DIV[15:0]
r
r
Bits 15:0 RTC_DIV[15:0]: RTC clock divider low
Doc ID16188 Rev 5
479/713
482
Real-time clock (RTC)
17.4.5
RM0041
RTC counter register (RTC_CNTH / RTC_CNTL)
The RTC core has one 32-bit programmable counter, accessed through two 16-bit registers;
the count rate is based on the TR_CLK time reference, generated by the prescaler.
RTC_CNT registers keep the counting value of this counter. They are write-protected by bit
RTOFF in the RTC_CR register, and a write operation is allowed if the RTOFF value is ‘1’. A
write operation on the upper (RTC_CNTH) or lower (RTC_CNTL) registers directly loads the
corresponding programmable counter and reloads the RTC Prescaler. When reading, the
current value in the counter (system date) is returned.
RTC counter register high (RTC_CNTH)
Address offset: 0x18
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
RTC_CNT[31:16]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 RTC_CNT[31:16]: RTC counter high
Reading the RTC_CNTH register, the current value of the high part of the RTC Counter
register is returned. To write to this register it is necessary to enter configuration mode (see
Section 17.3.4: Configuring RTC registers).
RTC counter register low (RTC_CNTL)
Address offset: 0x1C
Reset value: 0x0000
15
14
13
12
11
10
9
rw
rw
rw
rw
rw
rw
rw
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
RTC_CNT[15:0]
rw
rw
Bits 15:0 RTC_CNT[15:0]: RTC counter low
Reading the RTC_CNTL register, the current value of the lower part of the RTC Counter
register is returned. To write to this register it is necessary to enter configuration mode (see
Section 17.3.4: Configuring RTC registers).
480/713
Doc ID16188 Rev 5
RM0041
Real-time clock (RTC)
17.4.6
RTC alarm register high (RTC_ALRH / RTC_ALRL)
When the programmable counter reaches the 32-bit value stored in the RTC_ALR register,
an alarm is triggered and the RTC_alarmIT interrupt request is generated. This register is
write-protected by the RTOFF bit in the RTC_CR register, and a write operation is allowed if
the RTOFF value is ‘1’.
RTC alarm register high (RTC_ALRH)
Address offset: 0x20
Write only (see Section 17.3.4: Configuring RTC registers)
Reset value: 0xFFFF
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
w
w
w
w
w
w
w
RTC_ALR[31:16]
w
w
w
w
w
w
w
w
w
Bits 15:0 RTC_ALR[31:16]: RTC alarm high
The high part of the alarm time is written by software in this register. To write to this register
it is necessary to enter configuration mode (see Section 17.3.4: Configuring RTC registers).
RTC alarm register low (RTC_ALRL)
Address offset: 0x24
Write only (see Section 17.3.4: Configuring RTC registers)
Reset value: 0xFFFF
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
w
w
w
w
w
w
w
RTC_ALR[15:0]
w
w
w
w
w
w
w
w
w
Bits 15:0 RTC_ALR[15:0]: RTC alarm low
The low part of the alarm time is written by software in this register. To write to this register it
is necessary to enter configuration mode (see Section 17.3.4: Configuring RTC registers).
Doc ID16188 Rev 5
481/713
482
Real-time clock (RTC)
17.4.7
RM0041
RTC register map
RTC registers are mapped as 16-bit addressable registers as described in the table below:
1 0 0 0 0 0
Reset value
0x08
RTC_PRLH
PRL[19:16]
Reserved
0 0 0 0
Reset value
0x0C
RTC_PRLL
Reserved
RTC_DIVH
Reserved
RTC_DIVL
Reserved
RTC_CNTH
Reserved
RTC_CNTL
Reserved
RTC_ALRH
Reserved
RTC_ALRL
ALR[31:16]
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Reset value
0x24
CNT[15:0]
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x20
CNT[13:16]
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x1C
DIV[15:0]
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x18
DIV[31:16]
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x14
PRL[15:0]
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Reset value
0x10
RSF
Reserved
CNF
RTOFF
RTC_CRL
SECF
0 0 0
Reset value
0x04
SECIE
OWIE
Reserved
ALRIE
RTC_CRH
ALRF
0x00
Register
OWF
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 85. RTC register map and reset values
Reserved
ALR[15:0]
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Reset value
Refer to Table 1: Low and medium-density device register boundary addresses and Table 2:
High-density device register boundary addresses for the register boundary addresses.
482/713
Doc ID16188 Rev 5
RM0041
18
Independent watchdog (IWDG)
Independent watchdog (IWDG)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
18.1
IWDG introduction
The devices have two embedded watchdog peripherals which offer a combination of high
safety level, timing accuracy and flexibility of use. Both watchdog peripherals (Independent
and Window) serve to detect and resolve malfunctions due to software failure, and to trigger
system reset or an interrupt (window watchdog only) when the counter reaches a given
timeout value.
The independent watchdog (IWDG) is clocked by its own dedicated low-speed clock (LSI)
and thus stays active even if the main clock fails. The window watchdog (WWDG) clock is
prescaled from the APB1 clock and has a configurable time-window that can be
programmed to detect abnormally late or early application behavior.
The IWDG is best suited to applications which require the watchdog to run as a totally
independent process outside the main application, but have lower timing accuracy
constraints. The WWDG is best suited to applications which require the watchdog to react
within an accurate timing window. For further information on the window watchdog, refer to
Section 19 on page 489.
18.2
18.3
IWDG main features
•
Free-running downcounter
•
clocked from an independent RC oscillator (can operate in Standby and Stop modes)
•
Reset (if watchdog activated) when the downcounter value of 0x000 is reached
IWDG functional description
Figure 199 shows the functional blocks of the independent watchdog module.
When the independent watchdog is started by writing the value 0xCCCC in the Key register
(IWDG_KR), the counter starts counting down from the reset value of 0xFFF. When it
reaches the end of count value (0x000) a reset signal is generated (IWDG reset).
Whenever the key value 0xAAAA is written in the IWDG_KR register, the IWDG_RLR value
is reloaded in the counter and the watchdog reset is prevented.
Doc ID16188 Rev 5
483/713
488
Independent watchdog (IWDG)
18.3.1
RM0041
Hardware watchdog
If the “Hardware watchdog” feature is enabled through the device option bits, the watchdog
is automatically enabled at power-on, and will generate a reset unless the Key register is
written by the software before the counter reaches end of count.
18.3.2
Register access protection
Write access to the IWDG_PR and IWDG_RLR registers is protected. To modify them, first
write the code 0x5555 in the IWDG_KR register. A write access to this register with a
different value will break the sequence and register access will be protected again. This
implies that it is the case of the reload operation (writing 0xAAAA).
A status register is available to indicate that an update of the prescaler or the down-counter
reload value is on going.
18.3.3
Debug mode
When the microcontroller enters debug mode (Cortex®-M3 core halted), the IWDG counter
either continues to work normally or stops, depending on DBG_IWDG_STOP configuration
bit in DBG module. For more details, refer to Section 25.15.2: Debug support for timers,
watchdog and I2C.
Figure 199. Independent watchdog block diagram
#/2%
0RESCALERREGISTER
)7$'?02
3TATUSREGISTER
)7$'?32
2ELOADREGISTER
)7$'?2,2
+EYREGISTER
)7$'?+2
BITRELOADVALUE
BIT
,3)
K(Z PRESCALER
BITDOWNCOUNTER
)7$'RESET
6$$VOLTAGEDOMAIN
-36
Note:
The watchdog function is implemented in the VDD voltage domain that is still functional in
Stop and Standby modes.
Table 86. Min/max IWDG timeout period at 40 kHz (LSI)(1)
484/713
Prescaler divider
PR[2:0] bits
Min timeout (ms) RL[11:0]=
0x000
Max timeout (ms) RL[11:0]=
0xFFF
/4
0
0.1
409.6
/8
1
0.2
819.2
/16
2
0.4
1638.4
/32
3
0.8
3276.8
/64
4
1.6
6553.6
/128
5
3.2
13107.2
/256
6 (or 7)
6.4
26214.4
Doc ID16188 Rev 5
RM0041
Independent watchdog (IWDG)
1. These timings are given for a kHz clock but the microcontroller internal RC frequency can vary. refer to
the LSI oscillator characteristics table in the device datasheet for maximum and minimum values.
The LSI can be calibrated so as to compute the IWDG timeout with an acceptable accuracy.
For more details refer to Section 7.2.5: LSI clock.
18.4
IWDG registers
Refer to Section: List of abbreviations for registers for a list of abbreviations used in register
descriptions.
The peripheral registers have to be accessed by half-words (16 bits) or words (32 bits).
18.4.1
Key register (IWDG_KR)
Address offset: 0x00
Reset value: 0x0000 0000 (reset by Standby mode)
31 30 29 28 27 26 25
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
w
w
w
w
w
w
w
KEY[15:0]
Reserved
w
w
w
w
w
w
w
w
w
Bits 31:16 Reserved, must be kept at reset value.
Bits 15:0 KEY[15:0]: Key value (write only, read 0000h)
These bits must be written by software at regular intervals with the key value AAAAh,
otherwise the watchdog generates a reset when the counter reaches 0.
Writing the key value 5555h to enable access to the IWDG_PR and IWDG_RLR registers
(see Section 18.3.2)
Writing the key value CCCCh starts the watchdog (except if the hardware watchdog option is
selected)
18.4.2
Prescaler register (IWDG_PR)
Address offset: 0x04
Reset value: 0x0000 0000
31 30 29 28 27 26 25
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
Reserved
Doc ID16188 Rev 5
9
8
7
6
5
4
3
2
1
0
PR[2:0]
rw
rw
rw
485/713
488
Independent watchdog (IWDG)
RM0041
Bits 31:3 Reserved, must be kept at reset value.
Bits 2:0 PR[2:0]: Prescaler divider
These bits are write access protected seeSection 18.3.2. They are written by software to
select the prescaler divider feeding the counter clock. PVU bit of IWDG_SR must be reset in
order to be able to change the prescaler divider.
000: divider /4
001: divider /8
010: divider /16
011: divider /32
100: divider /64
101: divider /128
110: divider /256
111: divider /256
Note: Reading this register returns the prescaler value from the VDD voltage domain. This
value may not be up to date/valid if a write operation to this register is ongoing. For this
reason the value read from this register is valid only when the PVU bit in the IWDG_SR
register is reset.
18.4.3
Reload register (IWDG_RLR)
Address offset: 0x08
Reset value: 0x0000 0FFF (reset by Standby mode)
31 30 29 28 27 26 25
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
RL[11:0]
Reserved
rw rw
rw
rw
rw
rw
rw
Bits 31:12 Reserved, must be kept at reset value.
Bits11:0 RL[11:0]: Watchdog counter reload value
These bits are write access protected see Section 18.3.2. They are written by software to
define the value to be loaded in the watchdog counter each time the value AAAAh is written
in the IWDG_KR register. The watchdog counter counts down from this value. The timeout
period is a function of this value and the clock prescaler. Refer to Table 86.
The RVU bit in the IWDG_SR register must be reset in order to be able to change the reload
value.
Note: Reading this register returns the reload value from the VDD voltage domain. This value
may not be up to date/valid if a write operation to this register is ongoing on this
register. For this reason the value read from this register is valid only when the RVU bit
in the IWDG_SR register is reset.
18.4.4
Status register (IWDG_SR)
Address offset: 0x0C
Reset value: 0x0000 0000 (not reset by Standby mode)
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
Reserved
486/713
Doc ID16188 Rev 5
9
8
7
6
5
4
3
2
1
0
RVU PVU
r
r
RM0041
Independent watchdog (IWDG)
Bits 31:2 Reserved, must be kept at reset value.
Bit 1 RVU: Watchdog counter reload value update
This bit is set by hardware to indicate that an update of the reload value is ongoing. It is reset
by hardware when the reload value update operation is completed in the VDD voltage domain
(takes up to 5 RC 40 kHz cycles).
Reload value can be updated only when RVU bit is reset.
Bit 0 PVU: Watchdog prescaler value update
This bit is set by hardware to indicate that an update of the prescaler value is ongoing. It is
reset by hardware when the prescaler update operation is completed in the VDD voltage
domain (takes up to 5 RC 40 kHz cycles).
Prescaler value can be updated only when PVU bit is reset.
Note:
If several reload values or prescaler values are used by application, it is mandatory to wait
until RVU bit is reset before changing the reload value and to wait until PVU bit is reset
before changing the prescaler value. However, after updating the prescaler and/or the
reload value it is not necessary to wait until RVU or PVU is reset before continuing code
execution (even in case of low-power mode entry, the write operation is taken into account
and will complete)
Doc ID16188 Rev 5
487/713
488
Independent watchdog (IWDG)
18.4.5
RM0041
IWDG register map
The following table gives the IWDG register map and reset values.
0x04
0x08
0x0C
IWDG_KR
Reset value
IWDG_PR
Reset value
IWDG_SR
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PR[2:0]
0
0
0
1
1
1
0
0
RL[11:0]
Reserved
1
1
1
Reserved
Reset value
Refer to Section: Memory map for the register boundary addresses.
488/713
0
Reserved
Reset value
IWDG_RLR
KEY[15:0]
Reserved
PVU
0x00
Register
RVU
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 87. IWDG register map and reset values
Doc ID16188 Rev 5
1
1
1
1
1
1
RM0041
19
Window watchdog (WWDG)
Window watchdog (WWDG)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to the whole STM32F100xx family, unless otherwise specified.
19.1
WWDG introduction
The window watchdog is used to detect the occurrence of a software fault, usually
generated by external interference or by unforeseen logical conditions, which causes the
application program to abandon its normal sequence. The watchdog circuit generates an
MCU reset on expiry of a programmed time period, unless the program refreshes the
contents of the downcounter before the T6 bit becomes cleared. An MCU reset is also
generated if the 7-bit downcounter value (in the control register) is refreshed before the
downcounter has reached the window register value. This implies that the counter must be
refreshed in a limited window.
19.2
WWDG main features
•
Programmable free-running downcounter
•
Conditional reset
•
19.3
–
Reset (if watchdog activated) when the downcounter value becomes less than
0x40
–
Reset (if watchdog activated) if the downcounter is reloaded outside the window
(see Figure 201)
Early wakeup interrupt (EWI): triggered (if enabled and the watchdog activated) when
the downcounter is equal to 0x40.
WWDG functional description
If the watchdog is activated (the WDGA bit is set in the WWDG_CR register) and when the
7-bit downcounter (T[6:0] bits) rolls over from 0x40 to 0x3F (T6 becomes cleared), it initiates
a reset. If the software reloads the counter while the counter is greater than the value stored
in the window register, then a reset is generated.
Doc ID16188 Rev 5
489/713
495
Window watchdog (WWDG)
RM0041
Figure 200. Watchdog block diagram
5(6(7
:DWFKGRJFRQILJXUDWLRQUHJLVWHU::'*B&)5
FRPSDUDWRU
ZKHQ
7!:
: : : : : : :
:ULWH::'*B&5
:DWFKGRJFRQWUROUHJLVWHU::'*B&5
:'*$
3&/.
IURP5&&FORFNFRQWUROOHU
7
7 7 7
7 7 7
ELWGRZQFRXQWHU&17
:'*SUHVFDOHU
:'*7%
06Y9
The application program must write in the WWDG_CR register at regular intervals during
normal operation to prevent an MCU reset. This operation must occur only when the counter
value is lower than the window register value. The value to be stored in the WWDG_CR
register must be between 0xFF and 0xC0.
Enabling the watchdog
The watchdog is always disabled after a reset. It is enabled by setting the WDGA bit in the
WWDG_CR register, then it cannot be disabled again except by a reset.
Controlling the downcounter
This downcounter is free-running, counting down even if the watchdog is disabled. When
the watchdog is enabled, the T6 bit must be set to prevent generating an immediate reset.
The T[5:0] bits contain the number of increments which represents the time delay before the
watchdog produces a reset. The timing varies between a minimum and a maximum value
due to the unknown status of the prescaler when writing to the WWDG_CR register (see
Figure 201). The Configuration register (WWDG_CFR) contains the high limit of the window:
To prevent a reset, the downcounter must be reloaded when its value is lower than the
window register value and greater than 0x3F. Figure 201 describes the window watchdog
process.
Note:
The T6 bit can be used to generate a software reset (the WDGA bit is set and the T6 bit is
cleared).
Advanced watchdog interrupt feature
The Early Wakeup Interrupt (EWI) can be used if specific safety operations or data logging
must be performed before the actual reset is generated. The EWI interrupt is enabled by
setting the EWI bit in the WWDG_CFR register. When the downcounter reaches the value
0x40, an EWI interrupt is generated and the corresponding interrupt service routine (ISR)
can be used to trigger specific actions (such as communications or data logging), before
resetting the device.
490/713
Doc ID16188 Rev 5
RM0041
Window watchdog (WWDG)
In some applications, the EWI interrupt can be used to manage a software system check
and/or system recovery/graceful degradation, without generating a WWDG reset. In this
case, the corresponding interrupt service routine (ISR) should reload the WWDG counter to
avoid the WWDG reset, then trigger the required actions.
The EWI interrupt is cleared by writing '0' to the EWIF bit in the WWDG_SR register.
Note:
When the EWI interrupt cannot be served, e.g. due to a system lock in a higher priority task,
the WWDG reset will eventually be generated.
19.4
How to program the watchdog timeout
Warning:
When writing to the WWDG_CR register, always write 1 in the
T6 bit to avoid generating an immediate reset.
Figure 201. Window watchdog timing diagram
4;=#.4DOWNCOUNTER
7;=
X&
2EFRESHNOTALLOWED 2EFRESHALLOWED
4IME
4BIT
2%3%4
AIC
The formula to calculate the WWDG timeout value is given by:
WDGTB[1:0]
t WWDG = t PCLK1 × 4096 × 2
× ( T[5:0] + 1 )
( ms )
where:
tWWDG: WWDG timeout
tPCLK1: APB1 clock period measured in ms
4096: value corresponding to internal divider
Doc ID16188 Rev 5
491/713
495
Window watchdog (WWDG)
RM0041
As an example, let us assume APB1 frequency is equal to 24 MHz, WDGTB[1:0] is set to 3
and T[5:0] is set to 63:
3
t WWDG = 1 ⁄ 24000 × 4096 × 2 × ( 63 + 1 ) = 21.85ms
Refer to Table 94 for the minimum and maximum values of the tWWDG.
Table 88. Minimum and maximum timeout values @24 MHz (fPCLK1)
19.5
Prescaler
WDGTB
Min timeout value
Max timeout value
1
0
170.67 µs
10.92 ms
2
1
341.33 µs
21.85 ms
4
2
682.67 µs
43.69 ms
8
3
1365.33 µs
87.38 ms
Debug mode
When the microcontroller enters debug mode (Cortex®-M3 core halted), the WWDG counter
either continues to work normally or stops, depending on DBG_WWDG_STOP
configuration bit in DBG module. For more details, refer to Section 25.15.2: Debug support
for timers, watchdog and I2C.
492/713
Doc ID16188 Rev 5
RM0041
19.6
Window watchdog (WWDG)
WWDG registers
Refer to Section: List of abbreviations for registers for a list of abbreviations used in register
descriptions.
The peripheral registers have to be accessed by half-words (16 bits) or words (32 bits).
19.6.1
Control register (WWDG_CR)
Address offset: 0x00
Reset value: 0x0000 007F
31
30
29
28
27
26
25
24
15
14
13
12
11
10
9
8
23
22
21
20
6
5
4
19
18
17
16
3
2
1
0
Reserved
Reserved
7
WDGA
T[6:0]
rs
rw
Bits 31:8 Reserved, must be kept at reset value.
Bit 7 WDGA: Activation bit
This bit is set by software and only cleared by hardware after a reset. When WDGA = 1, the
watchdog can generate a reset.
0: Watchdog disabled
1: Watchdog enabled
Bits 6:0 T[6:0]: 7-bit counter (MSB to LSB)
These bits contain the value of the watchdog counter. It is decremented every (4096 x
2WDGTB[1:0]) PCLK1 cycles. A reset is produced when it rolls over from 0x40 to 0x3F (T6
becomes cleared).
Doc ID16188 Rev 5
493/713
495
Window watchdog (WWDG)
19.6.2
RM0041
Configuration register (WWDG_CFR)
Address offset: 0x04
Reset value: 0x0000 007F
31
30
29
28
27
26
25
24
23
22
21
20
6
5
4
19
18
17
16
3
2
1
0
Reserved
15
14
13
12
11
10
Reserved
9
8
7
EWI
WDGTB[1:0]
W[6:0]
rs
rw
rw
Bit 31:10 Reserved, must be kept at reset value.
Bit 9 EWI: Early wakeup interrupt
When set, an interrupt occurs whenever the counter reaches the value 0x40. This interrupt is
only cleared by hardware after a reset.
Bits 8:7 WDGTB[1:0]: Timer base
The time base of the prescaler can be modified as follows:
00: CK Counter Clock (PCLK1 div 4096) div 1
01: CK Counter Clock (PCLK1 div 4096) div 2
10: CK Counter Clock (PCLK1 div 4096) div 4
11: CK Counter Clock (PCLK1 div 4096) div 8
Bits 6:0 W[6:0]: 7-bit window value
These bits contain the window value to be compared to the downcounter.
19.6.3
Status register (WWDG_SR)
Address offset: 0x08
Reset value: 0x0000 0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
6
5
4
3
2
1
0
Reserved
15
14
13
12
11
10
9
8
7
Reserved
EWIF
rc_w0
Bits 31:1 Reserved, must be kept at reset value.
Bit 0 EWIF: Early wakeup interrupt flag
This bit is set by hardware when the counter has reached the value 0x40. It must be cleared
by software by writing ‘0’. A write of ‘1’ has no effect. This bit is also set if the interrupt is not
enabled.
494/713
Doc ID16188 Rev 5
RM0041
19.6.4
Window watchdog (WWDG)
WWDG register map
The following table gives the WWDG register map and reset values.
WWDG_CR
Reserved
Reserved
Reset value
0x08
WWDG_SR
WDGTB0
WWDG_CFR
EWI
0x04
0
WDGTB1
Reset value
0
0
0
Reserved
Reset value
T[6:0]
1
1
1
1
1
1
1
1
1
W[6:0]
1
1
1
1
1
EWIF
0x00
Register
WDGA
Offset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Table 89. WWDG register map and reset values
0
Refer to Section: Memory map for the register boundary addresses.
Doc ID16188 Rev 5
495/713
495
Flexible static memory controller (FSMC)
20
RM0041
Flexible static memory controller (FSMC)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
This section applies to high-density value line devices only.
20.1
FSMC main features
The FSMC block is able to interface with synchronous and asynchronous memories. Its
main purpose is to:
•
Translate the AHB transactions into the appropriate external device protocol
•
Meet the access timing requirements of the external devices
All external memories share the addresses, data and control signals with the controller.
Each external device is accessed by means of a unique chip select. The FSMC performs
only one access at a time to an external device.
The FSMC has the following main features:
•
496/713
Interfaces with static memory-mapped devices including:
–
Static random access memory (SRAM)
–
NOR Flash memory/OneNAND Flash memory
–
PSRAM (4 memory banks)
•
Supports burst mode access to synchronous devices (NOR Flash and PSRAM)
•
8- or 16-bit wide databus
•
Independent chip select control for each memory bank
•
Independent configuration for each memory bank
•
Programmable timings to support a wide range of devices, in particular:
–
Programmable wait states (up to 15)
–
Programmable bus turnaround cycles (up to 15)
–
Programmable output enable and write enable delays (up to 15)
–
Independent read and write timings and protocol, so as to support the widest
variety of memories and timings
•
Write enable and byte lane select outputs for use with PSRAM and SRAM devices
•
Translation of 32-bit wide AHB transactions into consecutive 16-bit or 8-bit accesses to
external 16-bit or 8-bit devices
•
A Write FIFO, 2-word long , each word is 32 bits wide, only stores data and not the
address. Therefore, this FIFO only buffers AHB write burst transactions. This makes it
possible to write to slow memories and free the AHB quickly for other operations. Only
one burst at a time is buffered: if a new AHB burst or single transaction occurs while an
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
operation is in progress, the FIFO is drained. The FSMC will insert wait states until the
current memory access is complete.
•
External asynchronous wait control
The FSMC registers that define the external device type and associated characteristics are
usually set at boot time and do not change until the next reset or power-up. However, it is
possible to change the settings at any time.
20.2
Block diagram
The FSMC consists of four main blocks:
•
The AHB interface (including the FSMC configuration registers)
•
The NOR Flash/PSRAM controller
•
The external device interface
The block diagram is shown in Figure 202.
Figure 202. FSMC block diagram
&3-#INTERRUPTTO.6)#
&ROMCLOCK
CONTROLLER
!("BUS
(#,+
#ONFIGURATION
REGISTERS
./2032!MEMORY
CONTROLLER
&3-#?.%;=
&3-#?.,OR.!$6
&3-#?.",;=
&3-#?#,+
&3-#?!;=
&3-#?$;=
./2032!SIGNALS
&3-#?./%
&3-#?.7%
&3-#?.7!)4
AIB
20.3
AHB interface
The AHB slave interface enables internal CPUs and other bus master peripherals to access
the external static memories.
AHB transactions are translated into the external device protocol. In particular, if the
selected external memory is 16 or 8 bits wide, 32-bit wide transactions on the AHB are split
into consecutive 16- or 8-bit accesses. The FSMC Chip Select (FSMC_NEx) does not
toggle between consecutive accesses except when performing accesses in mode D with the
extended mode enabled.
Doc ID16188 Rev 5
497/713
538
Flexible static memory controller (FSMC)
RM0041
The FSMC generates an AHB error in the following conditions:
•
When reading or writing to an FSMC bank which is not enabled
•
When reading or writing to the NOR Flash bank while the FACCEN bit is reset in the
FSMC_BCRx register.
The effect of this AHB error depends on the AHB master which has attempted the R/W
access:
•
If it is the Cortex®-M3 CPU, a hard fault interrupt is generated
•
If is a DMA, a DMA transfer error is generated and the corresponding DMA channel is
automatically disabled.
The AHB clock (HCLK) is the reference clock for the FSMC.
20.3.1
Supported memories and transactions
General transaction rules
The requested AHB transaction data size can be 8-, 16- or 32-bit wide whereas the
accessed external device has a fixed data width. This may lead to inconsistent transfers.
Therefore, some simple transaction rules must be followed:
•
AHB transaction size and memory data size are equal
There is no issue in this case.
•
AHB transaction size is greater than the memory size
In this case, the FSMC splits the AHB transaction into smaller consecutive memory
accesses in order to meet the external data width.
•
AHB transaction size is smaller than the memory size
Asynchronous transfers may or not be consistent depending on the type of external
device.
–
Asynchronous accesses to devices that have the byte select feature (SRAM,
ROM, PSRAM).
a) FSMC allows write transactions accessing the right data through its byte lanes
NBL[1:0]
b) Read transactions are allowed. All memory bytes are read and the useless
ones are discarded. The NBL[1:0] are kept low during read transactions.
–
Asynchronous accesses to devices that do not have the byte select feature (NOR
).
This situation occurs when a byte access is requested to a 16-bit wide Flash
memory. Clearly, the device cannot be accessed in byte mode (only 16-bit words
can be read from/written to the Flash memory) therefore:
a)
Write transactions are not allowed
b)
Read transactions are allowed. All memory bytes are read and the useless ones
are discarded. The NBL[1:0] are set to 0 during read transactions.
Configuration registers
The FSMC can be configured using a register set. See Section 20.5.6, for a detailed
description of the NOR Flash/PSRAM control registers.
498/713
Doc ID16188 Rev 5
RM0041
20.4
Flexible static memory controller (FSMC)
External device address mapping
From the FSMC point of view, the external memory is composed of a single fixed size bank
of 256 Mbytes (Refer to Figure 203):
•
Bank 1 used to address up to 4 NOR Flash or PSRAM memory devices. This bank is
split into 4 NOR/PSRAM subbanks with 4 dedicated Chip Selects, as follows:
–
Bank 1 - NOR/PSRAM 1
–
Bank 1 - NOR/PSRAM 2
–
Bank 1 - NOR/PSRAM 3
–
Bank 1 - NOR/PSRAM 4
For each bank the type of memory to be used is user-defined in the Configuration register.
Figure 203. FSMC memory banks
Bank
Address
Supported memory type
6000 0000h
Bank 1
NOR / PSRAM
4 × 64 MB
6FF F FFF Fh
ai18306
20.4.1
NOR/PSRAM address mapping
HADDR[27:26] bits are used to select one of the four memory banks as shown in Table 90.
Table 90. NOR/PSRAM bank selection
HADDR[27:26](1)
Selected bank
00
Bank 1 - NOR/PSRAM 1
01
Bank 1 - NOR/PSRAM 2
10
Bank 1 - NOR/PSRAM 3
11
Bank 1 - NOR/PSRAM 4
1. HADDR are internal AHB address lines that are translated to external memory.
HADDR[25:0] contain the external memory address. Since HADDR is a byte address
whereas the memory is addressed in words, the address actually issued to the memory
varies according to the memory data width, as shown in the following table.
Table 91. External memory address
(1)
Memory width
Data address issued to the memory
Maximum memory capacity (bits)
8-bit
HADDR[25:0]
64 Mbyte x 8 = 512 Mbit
16-bit
HADDR[25:1] >> 1
64 Mbyte/2 x 16 = 512 Mbit
Doc ID16188 Rev 5
499/713
538
Flexible static memory controller (FSMC)
RM0041
1. In case of a 16-bit external memory width, the FSMC will internally use HADDR[25:1] to generate the
address for external memory FSMC_A[24:0].
Whatever the external memory width (16-bit or 8-bit), FSMC_A[0] should be connected to external memory
address A[0].
Wrap support for NOR Flash/PSRAM
Wrap burst mode for synchronous memories is not supported. The memories must be
configured in linear burst mode of undefined length.
20.5
NOR Flash/PSRAM controller
The FSMC generates the appropriate signal timings to drive the following types of
memories:
•
•
•
Asynchronous SRAM and ROM
–
8-bit
–
16-bit
–
32-bit
PSRAM (Cellular RAM)
–
Asynchronous mode
–
Burst mode for synchronous accesses
NOR Flash
–
Asynchronous mode
–
Burst mode for synchronous accesses
–
Multiplexed or nonmultiplexed
The FSMC outputs a unique chip select signal NE[4:1] per bank. All the other signals
(addresses, data and control) are shared.
For synchronous accesses, the FSMC issues the clock (CLK) to the selected external
device only during the read/write transactions. This clock is a submultiple of the HCLK clock.
The size of each bank is fixed and equal to 64 Mbytes.
Each bank is configured by means of dedicated registers (see Section 20.5.6).
The programmable memory parameters include access timings (see Table 92) and support
for wait management (for PSRAM and NOR Flash accessed in burst mode).
Table 92. Programmable NOR/PSRAM access parameters
Parameter
500/713
Function
Access mode
Unit
Min.
Max.
Address
setup
Duration of the address
setup phase
Asynchronous
AHB clock cycle
(HCLK)
0
15
Address hold
Duration of the address hold Asynchronous,
phase
muxed I/Os
AHB clock cycle
(HCLK)
1
15
Data setup
Duration of the data setup
phase
Asynchronous
AHB clock cycle
(HCLK)
1
256
Bus turn
Duration of the bus
turnaround phase
Asynchronous and
AHB clock cycle
synchronous
(HCLK)
read/write
0
15
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Table 92. Programmable NOR/PSRAM access parameters (continued)
Parameter
20.5.1
Function
Access mode
Unit
Min.
Max.
Clock divide
ratio
Number of AHB clock cycles
(HCLK) to build one memory Synchronous
clock cycle (CLK)
AHB clock cycle
(HCLK)
2
16
Data latency
Number of clock cycles to
issue to the memory before
the first data of the burst
Memory clock
cycle (CLK)
2
17
Synchronous
External memory interface signals
Table 93, Table 94 and Table 95 list the signals that are typically used to interface NOR
Flash, SRAM and PSRAM.
Note:
Prefix “N”. specifies the associated signal as active low.
NOR Flash, nonmultiplexed I/Os
Table 93. Nonmultiplexed I/O NOR Flash
FSMC signal name
I/O
Function
CLK
O
Clock (for synchronous access)
A[25:0]
O
Address bus
D[15:0]
I/O
Bidirectional data bus
NE[x]
O
Chip select, x = 1..4
NOE
O
Output enable
NWE
O
Write enable
NL(=NADV)
O
Latch enable (this signal is called address
valid, NADV, by some NOR Flash devices)
NWAIT
I
NOR Flash wait input signal to the FSMC
NOR Flash memories are addressed in 16-bit words. The maximum capacity is 512 Mbit (26
address lines).
NOR Flash, multiplexed I/Os
Table 94. Multiplexed I/O NOR Flash
FSMC signal name
I/O
Function
CLK
O
Clock (for synchronous access)
A[25:16]
O
Address bus
AD[15:0]
I/O
16-bit multiplexed, bidirectional address/data bus
NE[x]
O
Chip select, x = 1..4
NOE
O
Output enable
NWE
O
Write enable
Doc ID16188 Rev 5
501/713
538
Flexible static memory controller (FSMC)
RM0041
Table 94. Multiplexed I/O NOR Flash (continued)
FSMC signal name
I/O
Function
NL(=NADV)
O
Latch enable (this signal is called address valid, NADV, by some NOR
Flash devices)
NWAIT
I
NOR Flash wait input signal to the FSMC
NOR-Flash memories are addressed in 16-bit words. The maximum capacity is 512 Mbit
(26 address lines).
PSRAM/SRAM, nonmultiplexed I/Os
Table 95. Nonmultiplexed I/Os PSRAM/SRAM
FSMC signal name
I/O
Function
CLK
O
Clock (only for PSRAM synchronous access)
A[25:0]
O
Address bus
D[15:0]
I/O
Data bidirectional bus
NE[x]
O
Chip select, x = 1..4 (called NCE by PSRAM (Cellular RAM i.e. CRAM))
NOE
O
Output enable
NWE
O
Write enable
NL(= NADV)
O
Address valid only for PSRAM input (memory signal name: NADV)
NWAIT
I
PSRAM wait input signal to the FSMC
NBL[1]
O
Upper byte enable (memory signal name: NUB)
NBL[0]
O
Lowed byte enable (memory signal name: NLB)
PSRAM memories are addressed in 16-bit words. The maximum capacity is 512 Mbit (26
address lines).
PSRAM, multiplexed I/Os
Table 96. Multiplexed I/O PSRAM
FSMC signal name
502/713
I/O
Function
CLK
O
Clock (for synchronous access)
A[25:16]
O
Address bus
AD[15:0]
I/O
16-bit multiplexed, bidirectional address/data bus
NE[x]
O
Chip select, x = 1..4 (called NCE by PSRAM (Cellular RAM i.e. CRAM))
NOE
O
Output enable
NWE
O
Write enable
NL(= NADV)
O
Address valid PSRAM input (memory signal name: NADV)
NWAIT
I
PSRAM wait input signal to the FSMC
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Table 96. Multiplexed I/O PSRAM (continued)
FSMC signal name
I/O
Function
NBL[1]
O
Upper byte enable (memory signal name: NUB)
NBL[0]
O
Lowed byte enable (memory signal name: NLB)
PSRAM memories are addressed in 16-bit words. The maximum capacity is 512 Mbit (26
address lines).
20.5.2
Supported memories and transactions
Table 97 below displays an example of the supported devices, access modes and
transactions when the memory data bus is 16-bit for NOR, PSRAM and SRAM.
Transactions not allowed (or not supported) by the FSMC in this example appear in gray.
Table 97. NOR Flash/PSRAM controller: example of supported memories
and transactions
Device
Mode
AHB
data
size
R/W
Memory
data size
Allowed/
not
allowed
Comments
Asynchronous R
8
16
Y
Asynchronous W
8
16
N
Asynchronous R
16
16
Y
Asynchronous W
16
16
Y
NOR Flash
Asynchronous R
(muxed I/Os
and nonmuxed Asynchronous W
I/Os)
Asynchronous
R
page
32
16
Y
Split into 2 FSMC accesses
32
16
Y
Split into 2 FSMC accesses
-
16
N
Mode is not supported
Synchronous
R
8
16
N
Synchronous
R
16
16
Y
Synchronous
R
32
16
Y
Doc ID16188 Rev 5
503/713
538
Flexible static memory controller (FSMC)
RM0041
Table 97. NOR Flash/PSRAM controller: example of supported memories
and transactions (continued)
Device
AHB
data
size
R/W
Memory
data size
Allowed/
not
allowed
Comments
Asynchronous R
8
16
Y
Asynchronous W
8
16
Y
Asynchronous R
16
16
Y
Asynchronous W
16
16
Y
Asynchronous R
PSRAM
Asynchronous W
(multiplexed
I/Os and
Asynchronous
R
nonmultiplexed page
I/Os)
Synchronous R
32
16
Y
Split into 2 FSMC accesses
32
16
Y
Split into 2 FSMC accesses
-
16
N
Mode is not supported
8
16
N
SRAM and
ROM
20.5.3
Mode
Use of byte lanes NBL[1:0]
Synchronous
R
16
16
Y
Synchronous
R
32
16
Y
Synchronous
W
8
16
Y
Synchronous
W
16/32
16
Y
Asynchronous R
8 / 16
16
Y
Asynchronous W
8 / 16
16
Y
Use of byte lanes NBL[1:0]
Asynchronous R
32
16
Y
Split into 2 FSMC accesses
Asynchronous W
32
16
Y
Split into 2 FSMC
accesses.
Use of byte lanes NBL[1:0]
Use of byte lanes NBL[1:0]
General timing rules
Signals synchronization
504/713
•
All controller output signals change on the rising edge of the internal clock (HCLK)
•
In synchronous mode (read or write), all output signals change on the rising edge of
HCLK. Whatever the CLKDIV value, all outputs change as follows:
–
NOEL/NWEL/ NEL/NADVL/ NADVH /NBLL/ Address valid outputs change on the
falling edge of FSMC_CLK clock.
–
NOEH/ NWEH / NEH/ NOEH/NBLH/ Address invalid outputs change on the rising
edge of FSMC_CLK clock.
Doc ID16188 Rev 5
RM0041
20.5.4
Flexible static memory controller (FSMC)
NOR Flash/PSRAM controller asynchronous transactions
Asynchronous static memories (NOR Flash memory, PSRAM, SRAM)
•
Signals are synchronized by the internal clock HCLK. This clock is not issued to the
memory
•
The FSMC always samples the data before de-asserting the NOE signals. This
guarantees that the memory data-hold timing constraint is met (chip enable high to
data transition, usually 0 ns min.)
•
If the extended mode is enabled (EXTMOD bit is set in the FSMC_BCRx register), up
to four extended modes (A, B, C and D) are available. It is possible to mix A, B, C and
D modes for read and write operations. For example, read operation can be performed
in mode A and write in mode B.
•
If the extended mode is disabled (EXTMOD bit is reset in the FSMC_BCRx register),
the FSMC can operate in Mode1 or Mode2 as follows:
–
Mode 1 is the default mode when SRAM/PSRAM memory type is selected
(MTYP[0:1] = 0x0 or 0x01 in the FSMC_BCRx register)
–
Mode 2 is the default mode when NOR memory type is selected (MTYP[0:1] =
0x10 in the FSMC_BCRx register).
Mode 1 - SRAM/PSRAM (CRAM)
The next figures show the read and write transactions for the supported modes followed by
the required configuration of FSMC _BCRx, and FSMC_BTRx/FSMC_BWTRx registers.
Figure 204. Mode1 read accesses
Memory transaction
A[25:0]
NBL[1:0]
NEx
NOE
NWE
High
data driven
by memory
D[15:0]
ADDSET
HCLK cycles
DATAST
HCLK cycles
ai15557
1. NBL[1:0] are driven low during read access.
Doc ID16188 Rev 5
505/713
538
Flexible static memory controller (FSMC)
RM0041
Figure 205. Mode1 write accesses
Memory transaction
A[25:0]
NBL[1:0]
NEx
NOE
1HCLK
NWE
D[15:0]
data driven by FSMC
ADDSET
HCLK cycles
(DATAST + 1)
HCLK cycles
ai15558
The one HCLK cycle at the end of the write transaction helps guarantee the address and
data hold time after the NWE rising edge. Due to the presence of this one HCLK cycle, the
DATAST value must be greater than zero (DATAST > 0).
Table 98. FSMC_BCRx bit fields
Bit
number
31-20
Value to set
Reserved
0x000
CBURSTRW
0x0 (no effect on asynchronous mode)
CPSIZE
0x0 (no effect on asynchronous mode)
15
ASYNCWAIT
Set to 1 if the memory supports this feature. Otherwise keep at
0.
14
EXTMOD
0x0
13
WAITEN
0x0 (no effect on asynchronous mode)
12
WREN
As needed
11
WAITCFG
Don’t care
10
WRAPMOD
0x0
9
WAITPOL
Meaningful only if bit 15 is 1
8
BURSTEN
0x0
7
Reserved
0x1
6
FACCEN
Don’t care
MWID
As needed
19
18:16
5-4
506/713
Bit name
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Table 98. FSMC_BCRx bit fields (continued)
Bit
number
3-2
Bit name
Value to set
MTYP[0:1]
As needed, exclude 0x2 (NOR Flash)
1
MUXE
0x0
0
MBKEN
0x1
Table 99. FSMC_BTRx bit fields
Bit
number
Bit name
31:30
Reserved
0x0
29-28
ACCMOD
Don’t care
27-24
DATLAT
Don’t care
23-20
CLKDIV
Don’t care
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST+1 HCLK cycles for
write accesses, DATAST HCLK cycles for read accesses).
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Value to set
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles).
Minimum value for ADDSET is 0.
Doc ID16188 Rev 5
507/713
538
Flexible static memory controller (FSMC)
RM0041
Mode A - SRAM/PSRAM (CRAM) OE toggling
Figure 206. ModeA read accesses
Memory transaction
A[25:0]
NBL[1:0]
NEx
NOE
NWE
High
data driven
by memory
D[15:0]
ADDSET
HCLK cycles
DATAST
HCLK cycles
ai15559
1. NBL[1:0] are driven low during read access.
Figure 207. ModeA write accesses
Memory transaction
A[25:0]
NBL[1:0]
NEx
NOE
1HCLK
NWE
data driven by FSMC
D[15:0]
ADDSET
HCLK cycles
(DATAST + 1)
HCLK cycles
ai15560
508/713
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
The differences compared with mode1 are the toggling of NOE and the independent read
and write timings.
Table 100. FSMC_BCRx bit fields
Bit
number
Bit name
31-20
Reserved
19
CBURSTRW
0x0 (no effect on asynchronous mode)
18:16
CPSIZE
0x0 (no effect on asynchronous mode)
15
ASYNCWAIT
14
EXTMOD
0x1
13
WAITEN
0x0 (no effect on asynchronous mode)
12
WREN
As needed
11
WAITCFG
Don’t care
10
WRAPMOD
9
WAITPOL
Meaningful only if bit 15 is 1
8
BURSTEN
0x0
7
Reserved
0x1
6
FACCEN
Don’t care
5-4
MWID
As needed
3-2
MTYP[0:1]
1
MUXEN
0x0
0
MBKEN
0x1
Value to set
0x000
Set to 1 if the memory supports this feature. Otherwise keep at
0.
0x0
As needed, exclude 0x2 (NOR Flash)
Table 101. FSMC_BTRx bit fields
Bit
number
Bit name
31:30
Reserved
0x0
29-28
ACCMOD
0x0
27-24
DATLAT
Don’t care
23-20
CLKDIV
Don’t care
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST HCLK cycles) for
read accesses.
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Value to set
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles) for read
accesses.
Minimum value for ADDSET is 0.
Doc ID16188 Rev 5
509/713
538
Flexible static memory controller (FSMC)
RM0041
Table 102. FSMC_BWTRx bit fields
Bit
number
Bit name
31:30
Reserved
0x0
29-28
ACCMOD
0x0
27-24
DATLAT
Don’t care
23-20
CLKDIV
Don’t care
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST+1 HCLK cycles for
write accesses,
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Value to set
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles) for write
accesses.
Minimum value for ADDSET is 0.
Mode 2/B - NOR Flash
Figure 208. Mode2 and mode B read accesses
Memory transaction
A[25:0]
NADV
NEx
NOE
NWE
High
data driven
by memory
D[15:0]
ADDSET
HCLK cycles
DATAST
HCLK cycles
ai15561
510/713
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Figure 209. Mode2 write accesses
Memory transaction
A[25:0]
NADV
NEx
NOE
1HCLK
NWE
D[15:0]
data driven by FSMC
ADDSET
HCLK cycles
(DATAST + 1)
HCLK cycles
ai15562
Figure 210. Mode B write accesses
Memory transaction
A[25:0]
NADV
NEx
NOE
1HCLK
NWE
D[15:0]
data driven by FSMC
ADDSET
HCLK cycles
(DATAST + 1)
HCLK cycles
ai15563
The differences with mode1 are the toggling of NWE and the independent read and write
timings when extended mode is set (Mode B).
Doc ID16188 Rev 5
511/713
538
Flexible static memory controller (FSMC)
RM0041
Table 103. FSMC_BCRx bit fields
Bit
number
Bit name
31-20
Reserved
19
CBURSTRW
0x0 (no effect on asynchronous mode)
18:16
Reserved
0x0 (no effect on asynchronous mode)
15
ASYNCWAIT
14
EXTMOD
0x1 for mode B, 0x0 for mode 2
13
WAITEN
0x0 (no effect on asynchronous mode)
12
WREN
As needed
11
WAITCFG
Don’t care
10
WRAPMOD
9
WAITPOL
Meaningful only if bit 15 is 1
8
BURSTEN
0x0
7
Reserved
0x1
6
FACCEN
0x1
5-4
MWID
3-2
MTYP[0:1]
1
MUXEN
0x0
0
MBKEN
0x1
Value to set
0x000
Set to 1 if the memory supports this feature. Otherwise keep at
0.
0x0
As needed
0x2 (NOR Flash memory)
Table 104. FSMC_BTRx bit fields
512/713
Bit
number
Bit name
31:30
Reserved
0x0
29-28
ACCMOD
0x1
27-24
DATLAT
Don’t care
23-20
CLKDIV
Don’t care
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST HCLK cycles) for
read accesses.
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Value to set
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles) for read
accesses.
Minimum value for ADDSET is 0.
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Table 105. FSMC_BWTRx bit fields
Note:
Bit
number
Bit name
31:30
Reserved
0x0
29-28
ACCMOD
0x1
27-24
DATLAT
Don’t care
23-20
CLKDIV
Don’t care
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST+1 HCLK cycles for
write accesses,
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Value to set
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles) for write
accesses.
Minimum value for ADDSET is 0.
The FSMC_BWTRx register is valid only if extended mode is set (mode B), otherwise all its
content is don’t care.
Mode C - NOR Flash - OE toggling
Figure 211. Mode C read accesses
Memory transaction
A[25:0]
NADV
NEx
NOE
NWE
High
data driven
by memory
D[15:0]
ADDSET
HCLK cycles
DATAST
HCLK cycles
ai15564
Doc ID16188 Rev 5
513/713
538
Flexible static memory controller (FSMC)
RM0041
Figure 212. Mode C write accesses
Memory transaction
A[25:0]
NADV
NEx
NOE
1HCLK
NWE
D[15:0]
data driven by FSMC
ADDSET
HCLK cycles
(DATAST + 1)
HCLK cycles
ai15565
The differences compared with mode1 are the toggling of NOE and the independent read
and write timings.
Table 106. FSMC_BCRx bit fields
514/713
Bit No.
Bit name
Value to set
31-20
Reserved
19
CBURSTRW
0x0 (no effect on asynchronous mode)
18:16
CPSIZE
0x0 (no effect on asynchronous mode)
15
ASYNCWAIT
14
EXTMOD
0x1
13
WAITEN
0x0 (no effect on asynchronous mode)
12
WREN
As needed
11
WAITCFG
Don’t care
10
WRAPMOD
9
WAITPOL
Meaningful only if bit 15 is 1
8
BURSTEN
0x0
7
Reserved
0x1
6
FACCEN
0x1
5-4
MWID
3-2
MTYP[0:1]
0x000
Set to 1 if the memory supports this feature. Otherwise keep
at 0.
0x0
As needed
0x2 (NOR Flash memory)
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Table 106. FSMC_BCRx bit fields (continued)
Bit No.
Bit name
Value to set
1
MUXEN
0x0
0
MBKEN
0x1
Table 107. FSMC_BTRx bit fields
Bit
number
Bit name
31:30
Reserved
0x0
29-28
ACCMOD
0x2
27-24
DATLAT
0x0
23-20
CLKDIV
0x0
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST HCLK cycles) for
read accesses.
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Value to set
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles) for read
accesses.
Minimum value for ADDSET is 0.
Table 108. FSMC_BWTRx bit fields
Bit
number
Bit name
31:30
Reserved
0x0
29-28
ACCMOD
0x2
27-24
DATLAT
Don’t care
23-20
CLKDIV
Don’t care
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST+1 HCLK cycles for
write accesses,
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Value to set
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles) for write
accesses.
Minimum value for ADDSET is 0.
Doc ID16188 Rev 5
515/713
538
Flexible static memory controller (FSMC)
RM0041
Mode D - asynchronous access with extended address
Figure 213. Mode D read accesses
Memory transaction
A[25:0]
NADV
NEx
NOE
NWE
High
data driven
by memory
D[15:0]
ADDSET
HCLK cycles
DATAST
HCLK cycles
ADDHLD
HCLK cycles
ai15566
Figure 214. Mode D write accesses
Memory transaction
A[25:0]
NADV
NEx
NOE
1HCLK
NWE
data driven by FSMC
D[15:0]
ADDSET
HCLK cycles
516/713
ADDHLD
HCLK cycles
Doc ID16188 Rev 5
(DATAST+ 1)
HCLK cycles
ai15567
RM0041
Flexible static memory controller (FSMC)
The differences with mode1 are the toggling of NOE that goes on toggling after NADV
changes and the independent read and write timings.
Table 109. FSMC_BCRx bit fields
Bit No.
Bit name
Value to set
31-20
Reserved
19
CBURSTRW
0x0 (no effect on asynchronous mode)
18:16
CPSIZE
0x0 (no effect on asynchronous mode)
15
ASYNCWAIT
14
EXTMOD
0x1
13
WAITEN
0x0 (no effect on asynchronous mode)
12
WREN
As needed
11
WAITCFG
Don’t care
10
WRAPMOD
9
WAITPOL
Meaningful only if bit 15 is 1
8
BURSTEN
0x0
7
Reserved
0x1
6
FACCEN
Set according to memory support
5-4
MWID
As needed
3-2
MTYP[0:1]
As needed
1
MUXEN
0x0
0
MBKEN
0x1
0x000
Set to 1 if the memory supports this feature. Otherwise keep
at 0.
0x0
Table 110. FSMC_BTRx bit fields
Bit No.
Bit name
Value to set
31:30
Reserved
0x0
29-28
ACCMOD
0x3
27-24
DATLAT
Don’t care
23-20
CLKDIV
Don’t care
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST HCLK cycles) for
read accesses.
7-4
ADDHLD
Duration of the middle phase of the read access (ADDHLD HCLK
cycles)
3-0
ADDSET[3:0]
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles) for read
accesses. Minimum value for ADDSET is 1.
Doc ID16188 Rev 5
517/713
538
Flexible static memory controller (FSMC)
RM0041
Table 111. FSMC_BWTRx bit fields
Bit No.
Bit name
Value to set
31:30
Reserved
0x0
29-28
ACCMOD
0x3
27-24
DATLAT
0x0
23-20
CLKDIV
0x0
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase
7-4
ADDHLD
Duration of the middle phase of the write access (ADDHLD HCLK
cycles)
3-0
ADDSET[3:0]
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase . Minimum value for ADDSET is 1.
Muxed mode - multiplexed asynchronous access to NOR Flash memory
Figure 215. Multiplexed read accesses
Memory transaction
A[25:16]
NADV
NEx
NOE
NWE
AD[15:0]
High
Lower address
ADDSET
HCLK cycles
data driven
by memory
DATAST
ADDHLD
HCLK cycles
HCLK cycles
ai15568
518/713
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Figure 216. Multiplexed write accesses
-EMORYTRANSACTION
!;=
.!$6
.%X
./%
(#,+
.7%
,OWERADDRESS
!$;=
!$$3%4
(#,+CYCLES
!$$(,$
(#,+CYCLES
DATADRIVENBY&3-#
$!4!34
(#,+CYCLES
AI
The difference with mode D is the drive of the lower address byte(s) on the databus.
Table 112. FSMC_BCRx bit fields
Bit No.
Bit name
Value to set
31-21
Reserved
19
CBURSTRW
0x0 (no effect on asynchronous mode)
18:16
CPSIZE
0x0 (no effect on asynchronous mode)
15
ASYNCWAIT
14
EXTMOD
0x0
13
WAITEN
0x0 (no effect on asynchronous mode)
12
WREN
As needed
11
WAITCFG
Don’t care
10
WRAPMOD
9
WAITPOL
Meaningful only if bit 15 is 1
8
BURSTEN
0x0
7
Reserved
0x1
6
FACCEN
0x1
5-4
MWID
3-2
MTYP[0:1]
0x000
Set to 1 if the memory supports this feature. Otherwise keep at
0.
0x0
As needed
0x2 (NOR Flash memory)
Doc ID16188 Rev 5
519/713
538
Flexible static memory controller (FSMC)
RM0041
Table 112. FSMC_BCRx bit fields (continued)
Bit No.
Bit name
Value to set
1
MUXEN
0x1
0
MBKEN
0x1
Table 113. FSMC_BTRx bit fields
Bit No.
Bit name
Value to set
31:30
Reserved
0x0
29-28
ACCMOD
0x0
27-24
DATLAT
Don’t care
23-20
CLKDIV
Don’t care
19-16
BUSTURN
15-8
DATAST
Duration of the second access phase (DATAST HCLK cycles for
read accesses and DATAST+1 HCLK cycles for write accesses).
7-4
ADDHLD
Duration of the middle phase of the access (ADDHLD HCLK cycles).
3-0
ADDSET[3:0]
Time between NEx high to NEx low (BUSTURN HCLK)
Duration of the first access phase (ADDSET HCLK cycles).
Minimum value for ADDSET is 1.
WAIT management in asynchronous accesses
If the asynchronous memory asserts a WAIT signal to indicate that it is not yet ready to
accept or to provide data, the ASYNCWAIT bit has to be set in FSMC_BCRx register.
If the WAIT signal is active (high or low depending on the WAITPOL bit), the second access
phase (Data setup phase) programmed by the DATAST bits, is extended until WAIT
becomes inactive. Unlike the data setup phase, the first access phases (Address setup and
Address hold phases), programmed by the ADDSET[3:0] and ADDHLD bits, are not WAIT
sensitive and so they are not prolonged.
The data setup phase (DATAST in the FSMC_BTRx register) must be programmed so that
WAIT can be detected 4 HCLK cycles before the end of memory transaction. The following
cases must be considered:
520/713
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
1.
DATAST in FSMC_BTRx register) Memory asserts the WAIT signal aligned to
NOE/NWE which toggles:
DATAST ≥ ( 4 × HCLK ) + max_wait_assertion_time
2.
Memory asserts the WAIT signal aligned to NEx (or NOE/NWE not toggling):
if
max_wait_assertion_time > address_phase + hold_phase
then
DATAST ≥ ( 4 × HCLK ) + ( max_wait_assertion_time
– address_phase – hold_phase )
otherwise
DATAST ≥ 4 × HCLK
where max_wait_assertion_time is the maximum time taken by the memory to assert
the WAIT signal once NEx/NOE/NWE is low.
Figure 217 and Figure 218 show the number of HCLK clock cycles that are added to the
memory access after WAIT is released by the asynchronous memory (independently of the
above cases).
Figure 217. Asynchronous wait during a read access
-EMORYTRANSACTION
!;=
ADDRESSPHASE
DATASETUPPHASE
.%X
.7!)4
DONTCARE
DONTCARE
./%
DATADRIVEN
BYMEMORY
$;=
(#,+
1. NWAIT polarity depends on WAITPOL bit setting in FSMC_BCRx register.
Doc ID16188 Rev 5
521/713
538
Flexible static memory controller (FSMC)
RM0041
Figure 218. Asynchronous wait during a write access
-EMORYTRANSACTION
!;=
ADDRESSPHASE
DATASETUPPHASE
.%X
.7!)4
DONTCARE
DONTCARE
(#,+
.7%
$;=
DATADRIVENBY&3-#
(#,+
AIC
1. NWAIT polarity depends on WAITPOL bit setting in FSMC_BCRx register.
522/713
Doc ID16188 Rev 5
RM0041
20.5.5
Flexible static memory controller (FSMC)
Synchronous transactions
The memory clock, CLK, is a submultiple of HCLK according to the value of parameter
CLKDIV.
NOR Flash memories specify a minimum time from NADV assertion to CLK high. To meet
this constraint, the FSMC does not issue the clock to the memory during the first internal
clock cycle of the synchronous access (before NADV assertion). This guarantees that the
rising edge of the memory clock occurs in the middle of the NADV low pulse.
Data latency versus NOR Flash latency
The data latency is the number of cycles to wait before sampling the data. The DATLAT
value must be consistent with the latency value specified in the NOR Flash configuration
register. The FSMC does not include the clock cycle when NADV is low in the data latency
count.
Caution:
Some NOR Flash memories include the NADV Low cycle in the data latency count, so the
exact relation between the NOR Flash latency and the FMSC DATLAT parameter can be
either of:
•
NOR Flash latency = (DATLAT + 2) CLK clock cycles
•
NOR Flash latency = (DATLAT + 3) CLK clock cycles
Some recent memories assert NWAIT during the latency phase. In such cases DATLAT can
be set to its minimum value. As a result, the FSMC samples the data and waits long enough
to evaluate if the data are valid. Thus the FSMC detects when the memory exits latency and
real data are taken.
Other memories do not assert NWAIT during latency. In this case the latency must be set
correctly for both the FSMC and the memory, otherwise invalid data are mistaken for good
data, or valid data are lost in the initial phase of the memory access.
Single-burst transfer
When the selected bank is configured in burst mode for synchronous accesses, if for
example an AHB single-burst transaction is requested on 16-bit memories, the FSMC
performs a burst transaction of length 1 (if the AHB transfer is 16-bit), or length 2 (if the AHB
transfer is 32-bit) and de-assert the chip select signal when the last data is strobed.
Clearly, such a transfer is not the most efficient in terms of cycles (compared to an
asynchronous read). Nevertheless, a random asynchronous access would first require to reprogram the memory access mode, which would altogether last longer.
Cross boundary page for Cellular RAM 1.5
Cellular RAM 1.5 does not allow burst access to cross the page boundary. The FSMC
controller allows to split automatically the burst access when the memory page size is
reached by configuring the CPSIZE bits in the FSMC_BCR1 register following the memory
page size.
Wait management
For synchronous NOR Flash memories, NWAIT is evaluated after the programmed latency
period, (DATLAT+2) CLK clock cycles.
Doc ID16188 Rev 5
523/713
538
Flexible static memory controller (FSMC)
RM0041
If NWAIT is sensed active (low level when WAITPOL = 0, high level when WAITPOL = 1),
wait states are inserted until NWAIT is sensed inactive (high level when WAITPOL = 0, low
level when WAITPOL = 1).
When NWAIT is inactive, the data is considered valid either immediately (bit WAITCFG = 1)
or on the next clock edge (bit WAITCFG = 0).
During wait-state insertion via the NWAIT signal, the controller continues to send clock
pulses to the memory, keeping the chip select and output enable signals valid, and does not
consider the data valid.
There are two timing configurations for the NOR Flash NWAIT signal in burst mode:
•
Flash memory asserts the NWAIT signal one data cycle before the wait state (default
after reset)
•
Flash memory asserts the NWAIT signal during the wait state
These two NOR Flash wait state configurations are supported by the FSMC, individually for
each chip select, thanks to the WAITCFG bit in the FSMC_BCRx registers (x = 0..3).
Figure 219. Wait configurations
-EMORYTRANSACTIONBURSTOFHALFWORDS
(#,+
#,+
!;=
ADDR;=
.!$6
.7!)4
7!)4#&'
.7!)4
7!)4#&'
INSERTEDWAITSTATE
!$;=
AADDR;=
DATA
DATA
DATA
AIB
524/713
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Figure 220. Synchronous multiplexed read mode - NOR, PSRAM (CRAM)
0HPRU\WUDQVDFWLRQ EXUVWRIKDOIZRUGV
+&/.
&/.
$>@
DGGU>@
1([
12(
1:(
+LJK
1$'9
1:$,7
:$,7&)*
'$7/$7
&/.F\FOHV
$'>@
$GGU>@
LQVHUWHGZDLWVWDWH
GDWD
FORFN FORFN
F\FOH
F\FOH
GDWD
'DWDVWUREHV
GDWD
GDWD
'DWDVWUREHV
DLI
1. Byte lane outputs BL are not shown; for NOR access, they are held high, and, for PSRAM (CRAM) access,
they are held low.
2. NWAIT polarity is set to 0.
Table 114. FSMC_BCRx bit fields
Bit No.
Bit name
Value to set
31-20
Reserved
19
CBURSTRW
No effect on synchronous read
18-16
CPSIZE
As needed (0x1 for CRAM 1.5)
15
ASCYCWAIT
0x0
14
EXTMOD
0x0
13
WAITEN
Set to 1 if the memory supports this feature, otherwise keep at 0.
12
WREN
no effect on synchronous read
11
WAITCFG
to be set according to memory
10
WRAPMOD
9
WAITPOL
to be set according to memory
8
BURSTEN
0x1
7
Reserved
0x1
6
FACCEN
Set according to memory support (NOR Flash memory)
5-4
MWID
0x000
0x0
As needed
Doc ID16188 Rev 5
525/713
538
Flexible static memory controller (FSMC)
RM0041
Table 114. FSMC_BCRx bit fields (continued)
Bit No.
Bit name
Value to set
3-2
MTYP[0:1]
0x1 or 0x2
1
MUXEN
As needed
0
MBKEN
0x1
Table 115. FSMC_BTRx bit fields
526/713
Bit No.
Bit name
Value to set
31:30
Reserved
0x0
29:28
ACCMOD
0x0
27-24
DATLAT
Data latency
23-20
CLKDIV
0x0 to get CLK = HCLK (not supported)
0x1 to get CLK = 2 × HCLK
..
19-16
BUSTURN
15-8
DATAST
Don’t care
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Don’t care
Time between NEx high to NEx low (BUSTURN HCLK)
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Figure 221. Synchronous multiplexed write mode - PSRAM (CRAM)
-EMORYTRANSACTIONBURSTOFHALFWORDS
(#,+
#,+
!;=
ADDR;=
.%X
(I:
./%
.7%
.!$6
.7!)4
7!)4#&'
$!4,!4
#,+CYCLES
!$;=
!DDR;=
INSERTEDWAITSTATE
DATA
DATA
CLOCK CLOCK
AIF
1. Memory must issue NWAIT signal one cycle in advance, accordingly WAITCFG must be programmed to 0.
2. NWAIT polarity is set to 0.
3. Byte Lane (NBL) outputs are not shown, they are held low while NEx is active.
Table 116. FSMC_BCRx bit fields
Bit No.
Bit name
Value to set
31-20
Reserved
19
CBURSTRW
18-16
CPSIZE
15
ASCYCWAIT
0x0
14
EXTMOD
0x0
13
WAITEN
Set to 1 if the memory supports this feature, otherwise keep at 0.
12
WREN
0x1
11
WAITCFG
0x0
10
WRAPMOD
0x0
0x000
0x1
As needed (0x1 for CRAM 1.5)
Doc ID16188 Rev 5
527/713
538
Flexible static memory controller (FSMC)
RM0041
Table 116. FSMC_BCRx bit fields (continued)
Bit No.
Bit name
Value to set
9
WAITPOL
to be set according to memory
8
BURSTEN
no effect on synchronous write
7
Reserved
0x1
6
FACCEN
Set according to memory support
5-4
MWID
3-2
MTYP[0:1]
1
MUXEN
As needed
0
MBKEN
0x1
As needed
0x1
Table 117. FSMC_BTRx bit fields
528/713
Bit No.
Bit name
Value to set
31:30
Reserved
0x0
29:28
ACCMOD
0x0
27-24
DATLAT
Data latency
23-20
CLKDIV
0x0 to get CLK = HCLK (not supported)
0x1 to get CLK = 2 × HCLK
19-16
BUSTURN
15-8
DATAST
Don’t care
7-4
ADDHLD
Don’t care
3-0
ADDSET[3:0]
Don’t care
Time between NEx high to NEx low (BUSTURN HCLK)
Doc ID16188 Rev 5
RM0041
20.5.6
Flexible static memory controller (FSMC)
NOR/PSRAM control registers
The NOR/PSRAM control registers have to be accessed by words (32 bits).
SRAM/NOR-Flash chip-select control registers 1..4 (FSMC_BCR1..4)
Address offset: 0xA000 0000 + 8 * (x – 1), x = 1...4
Reset value: 0x0000 30DB for Bank1 and 0x0000 30D2 for Bank 2 to 4
BURSTEN
rw
rw
rw
rw
rw
rw
4
3
rw
2
rw
rw
rw
1
0
MBKEN
WAITPOL
rw
5
MUXEN
WRAPMOD
rw
6
MTYP[1:0]
WREN
WAITCFG
rw
7
MWID[1:0]
8
FACCEN
9
Reserved
14 13 12 11 10
WAITEN
rw
CPSIZE[2:0]
15
EXTMOD
Reserved
CBURSTRW
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ASCYCWAIT
This register contains the control information of each memory bank, used for SRAMs,
PSRAM and NOR Flash memories.
rw
rw
Bits 31: 20 Reserved, must be kept at reset value.
Bit 19 CBURSTRW: Write burst enable.
For Cellular RAM (PSRAM) memories, this bit enables the synchronous burst protocol
during write operations. The enable bit for synchronous read accesses is the BURSTEN
bit in the FSMC_BCRx register.
0: Write operations are always performed in asynchronous mode
1: Write operations are performed in synchronous mode.
Bits 18: 16 CPSIZE[2:0]: CRAM page size.
These are used for Cellular RAM 1.5 which does not allow burst access to cross the
address boundaries between pages. When these bits are configured, the FSMC
controller splits automatically the burst access when the memory page size is reached
(refer to memory datasheet for page size).
000: No burst split when crossing page boundary (default after reset)
001: 128 bytes
010: 256 bytes
011: 512 bytes
100: 1024 bytes
Others: reserved.
Bit 15 ASYNCWAIT: Wait signal during asynchronous transfers
This bit enables/disables the FSMC to use the wait signal even during an asynchronous
protocol.
0: NWAIT signal is not taken into account when running an asynchronous protocol
(default after reset)
1: NWAIT signal is taken into account when running an asynchronous protocol
Doc ID16188 Rev 5
529/713
538
Flexible static memory controller (FSMC)
RM0041
Bit 14 EXTMOD: Extended mode enable.
This bit enables the FSMC to program the write timings for non-multiplexed
asynchronous accesses inside the FSMC_BWTR register, thus resulting in different
timings for read and write operations.
0: values inside FSMC_BWTR register are not taken into account (default after reset)
1: values inside FSMC_BWTR register are taken into account
Note: When the extended mode is disabled, the FSMC can operate in Mode1 or Mode2
as follows:
–
Mode 1 is the default mode when the SRAM/PSRAM memory type is selected
(MTYP [0:1]=0x0 or 0x01)
–
Mode 2 is the default mode when the NOR memory type is selected
(MTYP [0:1]= 0x10).
Bit 13 WAITEN: Wait enable bit.
This bit enables/disables wait-state insertion via the NWAIT signal when accessing the
Flash memory in synchronous mode.
0: NWAIT signal is disabled (its level not taken into account, no wait state inserted after
the programmed Flash latency period)
1: NWAIT signal is enabled (its level is taken into account after the programmed Flash
latency period to insert wait states if asserted) (default after reset)
Bit 12 WREN: Write enable bit.
This bit indicates whether write operations are enabled/disabled in the bank by the
FSMC:
0: Write operations are disabled in the bank by the FSMC, an AHB error is reported,
1: Write operations are enabled for the bank by the FSMC (default after reset).
Bit 11 WAITCFG: Wait timing configuration.
The NWAIT signal indicates whether the data from the memory are valid or if a wait state
must be inserted when accessing the Flash memory in synchronous mode. This
configuration bit determines if NWAIT is asserted by the memory one clock cycle before
the wait state or during the wait state:
0: NWAIT signal is active one data cycle before wait state (default after reset),
1: NWAIT signal is active during wait state (not used for PRAM).
Bit 10 WRAPMOD: Wrapped burst mode support.
Defines whether the controller will or not split an AHB burst wrap access into two linear
accesses. Valid only when accessing memories in burst mode
0: Direct wrapped burst is not enabled (default after reset),
1: Direct wrapped burst is enabled.
Note: This bit has no effect as the CPU and DMA cannot generate wrapping burst
transfers.
Bit 9 WAITPOL: Wait signal polarity bit.
Defines the polarity of the wait signal from memory. Valid only when accessing the
memory in burst mode:
0: NWAIT active low (default after reset),
1: NWAIT active high.
Bit 8 BURSTEN: Burst enable bit.
This bit enables/disables synchronous accesses during read operations. It is valid only
for synchronous memories operating in burst mode:
0: Burst mode disabled (default after reset). Read accesses are performed in
asynchronous mode.
1: Burst mode enable. Read accesses are performed in synchronous mode.
530/713
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Bit 7 Reserved, must be kept at reset value.
Bit 6 FACCEN: Flash access enable
Enables NOR Flash memory access operations.
0: Corresponding NOR Flash memory access is disabled
1: Corresponding NOR Flash memory access is enabled (default after reset)
Bits 5:4 MWID[1:0]: Memory databus width.
Defines the external memory device width, valid for all type of memories.
00: 8 bits,
01: 16 bits (default after reset),
10: reserved, do not use,
11: reserved, do not use.
Bits 3:2 MTYP[1:0]: Memory type.
Defines the type of external memory attached to the corresponding memory bank:
00: SRAM (default after reset for Bank 2...4)
01: PSRAM (CRAM)
10: NOR Flash/OneNAND Flash (default after reset for Bank 1)
11: reserved
Bit 1 MUXEN: Address/data multiplexing enable bit.
When this bit is set, the address and data values are multiplexed on the databus, valid
only with NOR and PSRAM memories:
0: Address/Data nonmultiplexed
1: Address/Data multiplexed on databus (default after reset)
Bit 0 MBKEN: Memory bank enable bit.
Enables the memory bank. After reset Bank1 is enabled, all others are disabled.
Accessing a disabled bank causes an ERROR on AHB bus.
0: Corresponding memory bank is disabled
1: Corresponding memory bank is enabled
Doc ID16188 Rev 5
531/713
538
Flexible static memory controller (FSMC)
RM0041
SRAM/NOR-Flash chip-select timing registers 1..4 (FSMC_BTR1..4)
Address offset: 0xA000 0000 + 0x04 + 8 * (x – 1), x = 1..4
Reset value: 0x0FFF FFFF
FSMC_BTRx bits are written by software to add a delay at the end of a read /write
transaction. This delay allows matching the minimum time between consecutive
transactions (tEHEL from NEx high to FSMC_NEx low) and the maximum time required by
the memory to free the data bus after a read access (tEHQZ).
This register contains the control information of each memory bank, used for SRAMs,
PSRAM and NOR Flash memories.If the EXTMOD bit is set in the FSMC_BCRx register,
then this register is partitioned for write and read access, that is, 2 registers are available:
one to configure read accesses (this register) and one to configure write accesses
(FSMC_BWTRx registers).
rw
rw
rw
rw
Bits 31:30
rw
rw
rw
rw
rw
rw
rw
rw
rw
8
7
6
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
5
4
3
2
rw
rw
rw
rw
rw
1
0
rw
rw
ADDSET[3:0]
ADDHLD[3:0]
9
DATAST[7:0]
BUSTURN[3:0]
CLKDIV[3:0]
DATLAT[3:0]
Reserved
ACCMOD[1:0]
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
Reserved, must be kept at reset value.
Bits 29:28 ACCMOD[1:0]: Access mode
Specifies the asynchronous access modes as shown in the timing diagrams. These bits are
taken into account only when the EXTMOD bit in the FSMC_BCRx register is 1.
00: access mode A
01: access mode B
10: access mode C
11: access mode D
Bits 27:24 DATLAT[3:0]: Data latency for synchronous NOR Flash memory (see note below bit
description table)
For synchronous NOR Flash memory with burst mode enabled, defines the number of
memory clock cycles (+2) to issue to the memory before reading/writing the first data.
This timing parameter is not expressed in HCLK periods, but in FSMC_CLK periods. In case
of PSRAM (CRAM), this field must be set to 0. In asynchronous NOR Flash or SRAM or
PSRAM , this value is don't care.
0000: Data latency of 2 CLK clock cycles for first burst access
1111: Data latency of 17 CLK clock cycles for first burst access (default value after reset)
Bits 23:20 CLKDIV[3:0]: Clock divide ratio (for FSMC_CLK signal)
Defines the period of FSMC_CLK clock output signal, expressed in number of HCLK cycles:
0000: Reserved
0001: FSMC_CLK period = 2 × HCLK periods
0010: FSMC_CLK period = 3 × HCLK periods
1111: FSMC_CLK period = 16 × HCLK periods (default value after reset)
In asynchronous NOR Flash, SRAM or PSRAM accesses, this value is don’t care.
532/713
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
Bits 19:16 BUSTURN[3:0]: Bus turnaround phase duration
These bits are written by software to add a delay at the end of a write-to-read (and read-to
write) transaction. The programmed bus turnaround delay is inserted between an
asynchronous read (muxed or D mode) or a write transaction and any other
asynchronous/synchronous read or write to/from a static bank (for a read operation, the bank
can be the same or a different one; for a write operation, the bank can be different except in r
muxed or D mode).
In some cases, the bus turnaround delay is fixed, whatever the programmed BUSTURN
values:
– No bus turnaround delay is inserted between two consecutive asynchronous write transfers
to the same static memory bank except in muxed and D mode.
– A bus turnaround delay of 1 FSMC clock cycle is inserted between:
–
Two consecutive asynchronous read transfers to the same static memory bank
except for muxed and D modes.
–
An asynchronous read to an asynchronous or synchronous write to any static bank
or dynamic bank except for muxed and D modes.
–
An asynchronous (modes 1, 2, A, B or C) read and a read operation from another
static bank.
– A bus turnaround delay of 2 FSMC clock cycles is inserted between:
–
Two consecutive synchronous write accesses (in burst or single mode) to the same
bank
–
A synchronous write (burst or single) access and an asynchronous write or read
transfer to or from static memory bank (the bank can be the same or different in case
of a read operation).
–
Two consecutive synchronous read accesses (in burst or single mode) followed by a
any synchronous/asynchronous read or write from/to another static memory bank.
– A bus turnaround delay of 3 FSMC clock cycles is inserted between:
–
Two consecutive synchronous write operations (in burst or single mode) to different
static banks.
–
A synchronous write access (in burst or single mode) and a synchronous read
access from the same or to a different bank.
0000: BUSTURN phase duration = 0 HCLK clock cycle added
...
1111: BUSTURN phase duration = 15 × HCLK clock cycles (default value after reset)
Doc ID16188 Rev 5
533/713
538
Flexible static memory controller (FSMC)
RM0041
Bits 15:8 DATAST[7:0]: Data-phase duration
These bits are written by software to define the duration of the data phase (refer to Figure 204
to Figure 216), used in asynchronous accesses:
0000 0000: Reserved
0000 0001: DATAST phase duration = 1 × HCLK clock cycles
0000 0010: DATAST phase duration = 2 × HCLK clock cycles
...
1111 1111: DATAST phase duration = 255 × HCLK clock cycles (default value after reset)
For each memory type and access mode data-phase duration, refer to the respective figure
(Figure 204 to Figure 216).
Example: Mode1, write access, DATAST=1: Data-phase duration= DATAST+1 = 2 HCLK clock
cycles.
Note: In synchronous accesses, this value is don't care.
Bits 7:4 ADDHLD[3:0]: Address-hold phase duration
These bits are written by software to define the duration of the address hold phase (refer to
Figure 213 to Figure 216), used in mode D and multiplexed accesses:
0000: Reserved
0001: ADDHLD phase duration =1 × HCLK clock cycle
0010: ADDHLD phase duration = 2 × HCLK clock cycle
...
1111: ADDHLD phase duration = 15 × HCLK clock cycles (default value after reset)
For each access mode address-hold phase duration, refer to the respective figure (Figure 213
to Figure 216).
Note: In synchronous accesses, this value is not used, the address hold phase is always 1
memory clock period duration.
Bits 3:0 ADDSET[3:0]: Address setup phase duration
These bits are written by software to define the duration of the address setup phase (refer to
Figure 204 to Figure 216), used in SRAMs, ROMs and asynchronous NOR Flash and PSRAM
accesses:
0000: ADDSET phase duration = 0 × HCLK clock cycle
...
1111: ADDSET phase duration = 15 × HCLK clock cycles (default value after reset)
For each access mode address setup phase duration, refer to the respective figure (refer to
Figure 204 to Figure 216).
Note: In synchronous NOR Flash and PSRAM accesses, this value is don’t care.
Note:
534/713
PSRAMs (CRAMs) have a variable latency due to internal refresh. Therefore these
memories issue the NWAIT signal during the whole latency phase to prolong the latency as
needed.
With PSRAMs (CRAMs) the DATLAT field must be set to 0, so that the FSMC exits its
latency phase soon and starts sampling NWAIT from memory, then starts to read or write
when the memory is ready.
This method can be used also with the latest generation of synchronous Flash memories
that issue the NWAIT signal, unlike older Flash memories (check the datasheet of the
specific Flash memory being used).
Doc ID16188 Rev 5
RM0041
Flexible static memory controller (FSMC)
SRAM/NOR-Flash write timing registers 1..4 (FSMC_BWTR1..4)
Address offset: 0xA000 0000 + 0x104 + 8 * (x – 1), x = 1...4
Reset value: 0x0FFF FFFF
This register contains the control information of each memory bank, used for SRAMs,
PSRAMs and NOR Flash memories. This register is active for write asynchronous access
only when the EXTMOD bit is set in the FSMC_BCRx register.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
Res.
ACCM
OD[2:0]
rw
rw
Bits 31:30
Reserved
BUSTURN[3:0]
rw
rw
rw
rw
9
8
DATAST[7:0]
rw
rw
rw
rw
rw
rw
7
6
5
4
ADDHLD[3:0]
rw
rw
rw
rw
rw
rw
3
2
1
0
ADDSET[3:0]
rw
rw
rw
rw
Reserved, must be kept at reset value.
Bits 29:28 ACCMOD[2:0]: Access mode.
Specifies the asynchronous access modes as shown in the next timing diagrams.These bits are
taken into account only when the EXTMOD bit in the FSMC_BCRx register is 1.
00: access mode A
01: access mode B
10: access mode C
11: access mode D
Bits 27:20
Reserved, must be kept at reset value.
Bits 19:16 BUSTURN[3:0]: Bus turnaround phase duration
The programmed bus turnaround delay is inserted between a an asynchronous write transfer and
any other asynchronous/synchronous read or write transfer to/from a static bank (for a read
operation, the bank can be the same or a different one; for a write operation, the bank can be
different except in r muxed or D mode).
In some cases, the bus turnaround delay is fixed, whatever the programmed BUSTURN values:
– No bus turnaround delay is inserted between two consecutive asynchronous write transfers to the
same static memory bank except in muxed and D mode.
– A bus turnaround delay of 2 FSMC clock cycles is inserted between:
–
Two consecutive synchronous write accesses (in burst or single mode) to the same bank.
–
A synchronous write transfer (in burst or single mode) and an asynchronous write or read
transfer to/from static a memory bank.
– A bus turnaround delay of 3 FSMC clock cycles is inserted between:
–
Two consecutive synchronous write accesses (in burst or single mode) to different static
banks.
–
A synchronous write transfer (in burst or single mode) and a synchronous read from the
same or from a different bank.
0000: BUSTURN phase duration = 0 HCLK clock cycle added
...
1111: BUSTURN phase duration = 15 HCLK clock cycles added (default value after reset)
Doc ID16188 Rev 5
535/713
538
Flexible static memory controller (FSMC)
RM0041
Bits 15:8 DATAST[7:0]: Data-phase duration.
These bits are written by software to define the duration of the data phase (refer to Figure 204 to
Figure 216), used in asynchronous SRAM, PSRAM and NOR Flash memory accesses:
0000 0000: Reserved
0000 0001: DATAST phase duration = 1 × HCLK clock cycles
0000 0010: DATAST phase duration = 2 × HCLK clock cycles
...
1111 1111: DATAST phase duration = 255 × HCLK clock cycles (default value after reset)
Note: In synchronous accesses, this value is don't care.
Bits 7:4 ADDHLD[3:0]: Address-hold phase duration.
These bits are written by software to define the duration of the address hold phase (refer to
Figure 213 to Figure 216), used in asynchronous multiplexed accesses:
0000: Reserved
0001: ADDHLD phase duration = 1 × HCLK clock cycle
0010: ADDHLD phase duration = 2 × HCLK clock cycle
...
1111: ADDHLD phase duration = 15 × HCLK clock cycles (default value after reset)
Note: In synchronous NOR Flash accesses, this value is not used, the address hold phase is always
1 Flash clock period duration.
Bits 3:0 ADDSET[3:0]: Address setup phase duration.
These bits are written by software to define the duration of the address setup phase in HCLK cycles
(refer to Figure 213 to Figure 216), used in asynchronous accessed:
0000: ADDSET phase duration = 0 × HCLK clock cycle
...
1111: ADDSET phase duration = 15 × HCLK clock cycles (default value after reset)
Note: In synchronous NOR Flash and PSRAM accesses, this value is don’t care.
536/713
Doc ID16188 Rev 5
0008
FSMC_BCR2
Reserved
0010
FSMC_BCR3
Reserved
0018
FSMC_BCR4
Reserved
0004
FSMC_BTR1
Res.
ACCMOD[1:0]
DATLAT[3:0]
CLKDIV[3:0]
000C
FSMC_BTR2
Res.
ACCMOD[1:0]
DATLAT[3:0]
CLKDIV[3:0]
0014
FSMC_BTR3
Res.
ACCMOD[1:0]
DATLAT[3:0]
CLKDIV[3:0]
001C
FSMC_BTR4
Res.
DATLAT[3:0]
CLKDIV[3:0]
0104
FSMC_BWTR
1
Res.
ACC
MOD
[1:0]
Res.
010C
FSMC_BWTR
2
Res.
ACC
MOD
[1:0]
Res.
Doc ID16188 Rev 5
ADDSET[3:0]
ADDHLD[3:0]
ADDHLD[3:0]
ADDSET[3:0]
DATAST[7:0]
DATAST[7:0]
DATAST[7:0]
ADDHLD[3:0]
ADDSET[3:0]
DATAST[7:0]
ADDHLD[3:0]
ADDSET[3:0]
DATAST[7:0]
ADDHLD[3:0]
ADDSET[3:0]
DATAST[7:0]
ADDHLD[3:0]
BUSTURN[3:0] BUSTURN[3:0] BUSTURN[3:0] BUSTURN[3:0] BUSTURN[3:0] BUSTURN[3:0]
Reserved
CPSIZE[2:0]
CPSIZE[2:0]
CPSIZE[2:0]
WREN
WAITCFG
WRAPMOD
WAITPOL
BURSTEN
Reserved
FACCEN
MWID[1:0]
WREN
WAITCFG
WRAPMOD
WAITPOL
BURSTEN
Reserved
FACCEN
MWID[1:0]
MUXEN
MBKEN
MUXEN
MBKEN
MTYP[0:1]
WAITEN
WAITEN
MTYP[0:1]
EXTMOD
EXTMOD
MBKEN
MUXEN
MTYP[0:1]
MWID[1:0]
FACCEN
Reserved
BURSTEN
WAITPOL
WRAPMOD
WAITCFG
WREN
WAITEN
EXTMOD
MBKEN
MUXEN
MTYP[0:1]
MWID[1:0]
FACCEN
Reserved
BURSTEN
WAITPOL
WRAPMOD
WAITCFG
WREN
WAITEN
EXTMOD
ASYNCWAIT ASYNCWAIT ASYNCWAIT ASYNCWAIT
CPSIZE[2:0]
CBURSTRW
FSMC_BCR1
CBURSTRW
0000
CBURSTRW
Register
CBURSTRW
Offset
ACCMOD[1:0]
0
1
2
20.5.7
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
RM0041
Flexible static memory controller (FSMC)
FSMC register map
The following table summarizes the FSMC registers.
Table 118. FSMC register map
ADDSET[3:0]
537/713
538
Flexible static memory controller (FSMC)
RM0041
FSMC_BWTR
3
Res.
ACC
MOD
[1:0]
Res.
011C
FSMC_BWTR
4
Res.
ACC
MOD
[1:0]
Res.
DATAST[7:0]
ADDHLD[3:0]
ADDSET[3:0]
DATAST[7:0]
ADDHLD[3:0]
ADDSET[3:0]
BUSTURN[3:0] BUSTURN[3:0]
Refer to Section: Memory map for the register boundary addresses.
538/713
Doc ID16188 Rev 5
0
0114
1
Register
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Offset
2
Table 118. FSMC register map (continued)
RM0041
21
Serial peripheral interface (SPI)
Serial peripheral interface (SPI)
Low-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 16 and 32 Kbytes.
Medium-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 64 and 128 Kbytes.
High-density value line devices are STM32F100xx microcontrollers where the Flash
memory density ranges between 256 and 512 Kbytes.
21.1
SPI introduction
The serial peripheral interface (SPI) allows half/ full-duplex, synchronous, serial
communication with external devices. The interface can be configured as the master and in
this case it provides the communication clock (SCK) to the external slave device. The
interface is also capable of operating in multimaster configuration.
It may be used for a variety of purposes, including simplex synchronous transfers on two
lines with a possible bidirectional data line or reliable communication using CRC checking.
Warning:
Since some SPI1and SPI3 pins may be mapped onto some
pins used by the JTAG interface (SPI1/3_NSS onto JTDI,
SPI1/3_SCK onto JTDO and SPI1/3_MISO onto NJTRST), you
may either:
– disable the JTAG and use the SWD interface prior to
configuring the pins listed as SPI IOs (when debugging the
application) or
– disable both JTAG/SWD interfaces (for standalone
applications).
For more information on the configuration of the JTAG/SWD
interface pins, refer to Section 7.3.3: JTAG/SWD alternate
function remapping.
Doc ID16188 Rev 5
539/713
568
Serial peripheral interface (SPI)
21.2
SPI main features
21.2.1
SPI features
540/713
RM0041
•
Full-duplex synchronous transfers on three lines
•
Simplex synchronous transfers on two lines with or without a bidirectional data line
•
8- or 16-bit transfer frame format selection
•
Master or slave operation
•
Multimaster mode capability
•
8 master mode baud rate prescalers (fPCLK/2 max.)
•
Slave mode frequency (fPCLK/2 max)
•
Faster communication for both master and slave
•
NSS management by hardware or software for both master and slave: dynamic change
of master/slave operations
•
Programmable clock polarity and phase
•
Programmable data order with MSB-first or LSB-first shifting
•
Dedicated transmission and reception flags with interrupt capability
•
SPI bus busy status flag
•
Hardware CRC feature for reliable communication:
–
CRC value can be transmitted as last byte in Tx mode
–
Automatic CRC error checking for last received byte
•
Master mode fault, overrun and CRC error flags with interrupt capability
•
1-byte transmission and reception buffer with DMA capability: Tx and Rx requests
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
21.3
SPI functional description
21.3.1
General description
The block diagram of the SPI is shown in Figure 222.
Figure 222. SPI block diagram
!DDRESSANDDATABUS
2EAD
2XBUFFER
30)?#2
-/3)
48%
)%
3HIFTREGISTER
-)3/
,3"FIRST
48$- 28$33/% !%. !%.
30)?32
"39
4XBUFFER
28.% %22
)%
)%
-/$ #2#
%22
&
/62
48% 28.%
7RITE
#OMMUNICATION
CONTROL
3#+
"AUDRATEGENERATOR
"2;=
,3"
&)234
30% "2
"2 "2
-342 #0/, #0(!
30)?#2
-ASTERCONTROLLOGIC
")$) ")$)
-/$% /%
#2# #2#
28
%.
.EXT $&& /.,9 33-
33)
.33
AI
Usually, the SPI is connected to external devices through 4 pins:
•
MISO: Master In / Slave Out data. This pin can be used to transmit data in slave mode
and receive data in master mode.
•
MOSI: Master Out / Slave In data. This pin can be used to transmit data in master
mode and receive data in slave mode.
•
SCK: Serial Clock output for SPI masters and input for SPI slaves.
•
NSS: Slave select. This is an optional pin to select a slave device. This pin acts as a
‘chip select’ to let the SPI master communicate with slaves individually and to avoid
contention on the data lines. Slave NSS inputs can be driven by standard IO ports on
the master device. The NSS pin may also be used as an output if enabled (SSOE bit)
and driven low if the SPI is in master configuration. In this manner, all NSS pins from
devices connected to the Master NSS pin see a low level and become slaves when
they are configured in NSS hardware mode. When configured in master mode with
NSS configured as an input (MSTR=1 and SSOE=0) and if NSS is pulled low, the SPI
Doc ID16188 Rev 5
541/713
568
Serial peripheral interface (SPI)
RM0041
enters the master mode fault state: the MSTR bit is automatically cleared and the
device is configured in slave mode (refer to Section 21.3.10: Error flags on page 560).
A basic example of interconnections between a single master and a single slave is
illustrated in Figure 223.
Figure 223. Single master/ single slave application
Master
MSBit
Slave
LSBit
8-bit shift register
SPI clock
generator
MSBit
MISO
MISO
MOSI
MOSI
SCK
SCK
NSS(1)
VDD
LSBit
8-bit shift register
NSS(1)
Not used if NSS is managed
by software
ai14745
1. Here, the NSS pin is configured as an input.
The MOSI pins are connected together and the MISO pins are connected together. In this
way data is transferred serially between master and slave (most significant bit first).
The communication is always initiated by the master. When the master device transmits
data to a slave device via the MOSI pin, the slave device responds via the MISO pin. This
implies full-duplex communication with both data out and data in synchronized with the
same clock signal (which is provided by the master device via the SCK pin).
Slave select (NSS) pin management
Hardware or software slave select management can be set using the SSM bit in the
SPI_CR1 register.
•
Software NSS management (SSM = 1)
The slave select information is driven internally by the value of the SSI bit in the
SPI_CR1 register. The external NSS pin remains free for other application uses.
•
Hardware NSS management (SSM = 0)
Two configurations are possible depending on the NSS output configuration (SSOE bit
in register SPI_CR2).
–
NSS output enabled (SSM = 0, SSOE = 1)
This configuration is used only when the device operates in master mode. The
NSS signal is driven low when the master starts the communication and is kept
low until the SPI is disabled.
–
NSS output disabled (SSM = 0, SSOE = 0)
This configuration allows multimaster capability for devices operating in master
mode. For devices set as slave, the NSS pin acts as a classical NSS input: the
slave is selected when NSS is low and deselected when NSS high.
542/713
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
Clock phase and clock polarity
Four possible timing relationships may be chosen by software, using the CPOL and CPHA
bits in the SPI_CR1 register. The CPOL (clock polarity) bit controls the steady state value of
the clock when no data is being transferred. This bit affects both master and slave modes. If
CPOL is reset, the SCK pin has a low-level idle state. If CPOL is set, the SCK pin has a
high-level idle state.
If the CPHA (clock phase) bit is set, the second edge on the SCK pin (falling edge if the
CPOL bit is reset, rising edge if the CPOL bit is set) is the MSBit capture strobe. Data are
latched on the occurrence of the second clock transition. If the CPHA bit is reset, the first
edge on the SCK pin (falling edge if CPOL bit is set, rising edge if CPOL bit is reset) is the
MSBit capture strobe. Data are latched on the occurrence of the first clock transition.
The combination of the CPOL (clock polarity) and CPHA (clock phase) bits selects the data
capture clock edge.
Figure 224, shows an SPI transfer with the four combinations of the CPHA and CPOL bits.
The diagram may be interpreted as a master or slave timing diagram where the SCK pin,
the MISO pin, the MOSI pin are directly connected between the master and the slave
device.
Note:
Prior to changing the CPOL/CPHA bits the SPI must be disabled by resetting the SPE bit.
Master and slave must be programmed with the same timing mode.
The idle state of SCK must correspond to the polarity selected in the SPI_CR1 register (by
pulling up SCK if CPOL=1 or pulling down SCK if CPOL=0).
The Data Frame Format (8- or 16-bit) is selected through the DFF bit in SPI_CR1 register,
and determines the data length during transmission/reception.
Doc ID16188 Rev 5
543/713
568
Serial peripheral interface (SPI)
RM0041
Figure 224. Data clock timing diagram
#0(!
#0/,
#0/,
-)3/
,3"IT
-3"IT
ORBITSDEPENDINGONTHE$ATAFRAMEFORMATBITSEE$&&IN30)?#2
-/3)
,3"IT
-3"IT
.33
TOSLAVE
#APTURESTROBE
#0(!
#0/,
#0/,
-)3/
-3"IT
,3"IT
ORBITSDEPENDINGONTHE$ATAFRAMEFORMATBITSEE$&&IN30)?#2
-/3)
-3"IT
,3"IT
.33
TOSLAVE
#APTURESTROBE
AIB
1. These timings are shown with the LSBFIRST bit reset in the SPI_CR1 register.
Data frame format
Data can be shifted out either MSB-first or LSB-first depending on the value of the
LSBFIRST bit in the SPI_CR1 Register.
Each data frame is 8 or 16 bits long depending on the size of the data programmed using
the DFF bit in the SPI_CR1 register. The selected data frame format is applicable for
transmission and/or reception.
21.3.2
Configuring the SPI in slave mode
In the slave configuration, the serial clock is received on the SCK pin from the master
device. The value set in the BR[2:0] bits in the SPI_CR1 register, does not affect the data
transfer rate.
Note:
It is recommended to enable the SPI slave before the master sends the clock. If not,
undesired data transmission might occur. The data register of the slave needs to be ready
before the first edge of the communication clock or before the end of the ongoing
communication. It is mandatory to have the polarity of the communication clock set to the
steady state value before the slave and the master are enabled.
Follow the procedure below to configure the SPI in slave mode:
544/713
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
Procedure
1.
Set the DFF bit to define 8- or 16-bit data frame format
2.
Select the CPOL and CPHA bits to define one of the four relationships between the
data transfer and the serial clock (see Figure 224). For correct data transfer, the CPOL
and CPHA bits must be configured in the same way in the slave device and the master
device.
3.
The frame format (MSB-first or LSB-first depending on the value of the LSBFIRST bit in
the SPI_CR1 register) must be the same as the master device.
4.
In Hardware mode (refer to Slave select (NSS) pin management on page 542), the
NSS pin must be connected to a low level signal during the complete byte transmit
sequence. In NSS software mode, set the SSM bit and clear the SSI bit in the SPI_CR1
register.
5.
Clear the MSTR bit and set the SPE bit (both in the SPI_CR1 register) to assign the
pins to alternate functions.
In this configuration the MOSI pin is a data input and the MISO pin is a data output.
Transmit sequence
The data byte is parallel-loaded into the Tx buffer during a write cycle.
The transmit sequence begins when the slave device receives the clock signal and the most
significant bit of the data on its MOSI pin. The remaining bits (the 7 bits in 8-bit data frame
format, and the 15 bits in 16-bit data frame format) are loaded into the shift-register. The
TXE flag in the SPI_SR register is set on the transfer of data from the Tx Buffer to the shift
register and an interrupt is generated if the TXEIE bit in the SPI_CR2 register is set.
Receive sequence
For the receiver, when data transfer is complete:
•
The Data in shift register is transferred to Rx Buffer and the RXNE flag (SPI_SR
register) is set
•
An Interrupt is generated if the RXNEIE bit is set in the SPI_CR2 register.
After the last sampling clock edge the RXNE bit is set, a copy of the data byte received in
the shift register is moved to the Rx buffer. When the SPI_DR register is read, the SPI
peripheral returns this buffered value.
Clearing of the RXNE bit is performed by reading the SPI_DR register.
Doc ID16188 Rev 5
545/713
568
Serial peripheral interface (SPI)
21.3.3
RM0041
Configuring the SPI in master mode
In the master configuration, the serial clock is generated on the SCK pin.
Procedure
1.
Select the BR[2:0] bits to define the serial clock baud rate (see SPI_CR1 register).
2.
Select the CPOL and CPHA bits to define one of the four relationships between the
data transfer and the serial clock (see Figure 224).
3.
Set the DFF bit to define 8- or 16-bit data frame format
4.
Configure the LSBFIRST bit in the SPI_CR1 register to define the frame format.
5.
If the NSS pin is required in input mode, in hardware mode, connect the NSS pin to a
high-level signal during the complete byte transmit sequence. In NSS software mode,
set the SSM and SSI bits in the SPI_CR1 register. If the NSS pin is required in output
mode, the SSOE bit only should be set.
6.
The MSTR and SPE bits must be set (they remain set only if the NSS pin is connected
to a high-level signal).
In this configuration the MOSI pin is a data output and the MISO pin is a data input.
Transmit sequence
The transmit sequence begins when a byte is written in the Tx Buffer.
The data byte is parallel-loaded into the shift register (from the internal bus) during the first
bit transmission and then shifted out serially to the MOSI pin MSB first or LSB first
depending on the LSBFIRST bit in the SPI_CR1 register. The TXE flag is set on the transfer
of data from the Tx Buffer to the shift register and an interrupt is generated if the TXEIE bit in
the SPI_CR2 register is set.
Receive sequence
For the receiver, when data transfer is complete:
•
The data in the shift register is transferred to the RX Buffer and the RXNE flag is set
•
An interrupt is generated if the RXNEIE bit is set in the SPI_CR2 register
At the last sampling clock edge the RXNE bit is set, a copy of the data byte received in the
shift register is moved to the Rx buffer. When the SPI_DR register is read, the SPI
peripheral returns this buffered value.
Clearing the RXNE bit is performed by reading the SPI_DR register.
A continuous transmit stream can be maintained if the next data to be transmitted is put in
the Tx buffer once the transmission is started. Note that TXE flag should be ‘1 before any
attempt to write the Tx buffer is made.
Note:
546/713
When a master is communicating with SPI slaves which need to be de-selected between
transmissions, the NSS pin must be configured as GPIO or another GPIO must be used and
toggled by software.
Doc ID16188 Rev 5
RM0041
21.3.4
Serial peripheral interface (SPI)
Configuring the SPI for half-duplex communication
The SPI is capable of operating in half-duplex mode in 2 configurations.
•
1 clock and 1 bidirectional data wire
•
1 clock and 1 data wire (receive-only or transmit-only)
1 clock and 1 bidirectional data wire (BIDIMODE=1)
This mode is enabled by setting the BIDIMODE bit in the SPI_CR1 register. In this mode
SCK is used for the clock and MOSI in master or MISO in slave mode is used for data
communication. The transfer direction (Input/Output) is selected by the BIDIOE bit in the
SPI_CR1 register. When this bit is 1, the data line is output otherwise it is input.
1 clock and 1 unidirectional data wire (BIDIMODE=0)
In this mode, the application can use the SPI either in transmit-only mode or in receive-only
mode.
•
Transmit-only mode is similar to full-duplex mode (BIDIMODE=0, RXONLY=0): the
data are transmitted on the transmit pin (MOSI in master mode or MISO in slave mode)
and the receive pin (MISO in master mode or MOSI in slave mode) can be used as a
general-purpose IO. In this case, the application just needs to ignore the Rx buffer (if
the data register is read, it does not contain the received value).
•
In receive-only mode, the application can disable the SPI output function by setting the
RXONLY bit in the SPI_CR2 register. In this case, it frees the transmit IO pin (MOSI in
master mode or MISO in slave mode), so it can be used for other purposes.
To start the communication in receive-only mode, configure and enable the SPI:
21.3.5
•
In master mode, the communication starts immediately and stops when the SPE bit is
cleared and the current reception stops. There is no need to read the BSY flag in this
mode. It is always set when an SPI communication is ongoing.
•
In slave mode, the SPI continues to receive as long as the NSS is pulled down (or the
SSI bit is cleared in NSS software mode) and the SCK is running.
Data transmission and reception procedures
Rx and Tx buffers
In reception, data are received and then stored into an internal Rx buffer while In
transmission, data are first stored into an internal Tx buffer before being transmitted.
A read access of the SPI_DR register returns the Rx buffered value whereas a write access
to the SPI_DR stores the written data into the Tx buffer.
Doc ID16188 Rev 5
547/713
568
Serial peripheral interface (SPI)
RM0041
Start sequence in master mode
•
•
•
•
In full-duplex (BIDIMODE=0 and RXONLY=0)
–
The sequence begins when data are written into the SPI_DR register (Tx buffer).
–
The data are then parallel loaded from the Tx buffer into the 8-bit shift register
during the first bit transmission and then shifted out serially to the MOSI pin.
–
At the same time, the received data on the MISO pin is shifted in serially to the 8bit shift register and then parallel loaded into the SPI_DR register (Rx buffer).
In unidirectional receive-only mode (BIDIMODE=0 and RXONLY=1)
–
The sequence begins as soon as SPE=1
–
Only the receiver is activated and the received data on the MISO pin are shifted in
serially to the 8-bit shift register and then parallel loaded into the SPI_DR register
(Rx buffer).
In bidirectional mode, when transmitting (BIDIMODE=1 and BIDIOE=1)
–
The sequence begins when data are written into the SPI_DR register (Tx buffer).
–
The data are then parallel loaded from the Tx buffer into the 8-bit shift register
during the first bit transmission and then shifted out serially to the MOSI pin.
–
No data are received.
In bidirectional mode, when receiving (BIDIMODE=1 and BIDIOE=0)
–
The sequence begins as soon as SPE=1 and BIDIOE=0.
–
The received data on the MOSI pin are shifted in serially to the 8-bit shift register
and then parallel loaded into the SPI_DR register (Rx buffer).
–
The transmitter is not activated and no data are shifted out serially to the MOSI
pin.
Start sequence in slave mode
•
•
•
548/713
In full-duplex mode (BIDIMODE=0 and RXONLY=0)
–
The sequence begins when the slave device receives the clock signal and the first
bit of the data on its MOSI pin. The 7 remaining bits are loaded into the shift
register.
–
At the same time, the data are parallel loaded from the Tx buffer into the 8-bit shift
register during the first bit transmission, and then shifted out serially to the MISO
pin. The software must have written the data to be sent before the SPI master
device initiates the transfer.
In unidirectional receive-only mode (BIDIMODE=0 and RXONLY=1)
–
The sequence begins when the slave device receives the clock signal and the first
bit of the data on its MOSI pin. The 7 remaining bits are loaded into the shift
register.
–
The transmitter is not activated and no data are shifted out serially to the MISO
pin.
In bidirectional mode, when transmitting (BIDIMODE=1 and BIDIOE=1)
–
The sequence begins when the slave device receives the clock signal and the first
bit in the Tx buffer is transmitted on the MISO pin.
–
The data are then parallel loaded from the Tx buffer into the 8-bit shift register
during the first bit transmission and then shifted out serially to the MISO pin. The
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
software must have written the data to be sent before the SPI master device
initiates the transfer.
–
•
No data are received.
In bidirectional mode, when receiving (BIDIMODE=1 and BIDIOE=0)
–
The sequence begins when the slave device receives the clock signal and the first
bit of the data on its MISO pin.
–
The received data on the MISO pin are shifted in serially to the 8-bit shift register
and then parallel loaded into the SPI_DR register (Rx buffer).
–
The transmitter is not activated and no data are shifted out serially to the MISO
pin.
Handling data transmission and reception
The TXE flag (Tx buffer empty) is set when the data are transferred from the Tx buffer to the
shift register. It indicates that the internal Tx buffer is ready to be loaded with the next data.
An interrupt can be generated if the TXEIE bit in the SPI_CR2 register is set. Clearing the
TXE bit is performed by writing to the SPI_DR register.
Note:
The software must ensure that the TXE flag is set to 1 before attempting to write to the Tx
buffer. Otherwise, it overwrites the data previously written to the Tx buffer.
The RXNE flag (Rx buffer not empty) is set on the last sampling clock edge, when the data
are transferred from the shift register to the Rx buffer. It indicates that data are ready to be
read from the SPI_DR register. An interrupt can be generated if the RXNEIE bit in the
SPI_CR2 register is set. Clearing the RXNE bit is performed by reading the SPI_DR
register.
For some configurations, the BSY flag can be used during the last data transfer to wait until
the completion of the transfer.
Full-duplex transmit and receive procedure in master or slave mode (BIDIMODE=0 and
RXONLY=0)
The software has to follow this procedure to transmit and receive data (see Figure 225 and
Figure 226):
1.
Enable the SPI by setting the SPE bit to 1.
2.
Write the first data item to be transmitted into the SPI_DR register (this clears the TXE
flag).
3.
Wait until TXE=1 and write the second data item to be transmitted. Then wait until
RXNE=1 and read the SPI_DR to get the first received data item (this clears the RXNE
bit). Repeat this operation for each data item to be transmitted/received until the n–1
received data.
4.
Wait until RXNE=1 and read the last received data.
5.
Wait until TXE=1 and then wait until BSY=0 before disabling the SPI.
This procedure can also be implemented using dedicated interrupt subroutines launched at
each rising edges of the RXNE or TXE flag.
Doc ID16188 Rev 5
549/713
568
Serial peripheral interface (SPI)
RM0041
Figure 225. TXE/RXNE/BSY behavior in Master / full-duplex mode (BIDIMODE=0 and
RXONLY=0) in case of continuous transfers
Example in Master mode with CPOL=1, CPHA=1
SCK
DATA1 = 0xF1
MISO/MOSI (out)
set by hardware
cleared by software
TXE flag
Tx buffer
(write SPI_DR)
DATA2 = 0xF2
DATA3 = 0xF3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
0xF1
BSY flag
set by hardware
cleared by software
0xF2
set by hardware
0xF3
set by hardware
reset by hardware
DATA1 = 0xA1
MISO/MOSI (in)
DATA 2 = 0xA2
DATA 3 = 0xA3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
set by hardware
RXNE flag
Rx buffer
(read SPI_DR)
cleared by software
0xA1
software
software waits
writes 0xF1 until TXE=1 and
into SPI_DR writes 0xF2 into
SPI_DR
software waits
software waits
until RXNE=1 until TXE=1 and
and reads 0xA1 writes 0xF3 into
from SPI_DR
SPI_DR
0xA2
software waits
until RXNE=1
and reads 0xA2
from SPI_ DR
0xA3
software waits
until RXNE=1
and reads 0xA3
from SPI_DR
ai17343
Figure 226. TXE/RXNE/BSY behavior in Slave / full-duplex mode (BIDIMODE=0,
RXONLY=0) in case of continuous transfers
Example in Slave mode with CPOL=1, CPHA=1
SCK
DATA 2 = 0xF2
DATA 1 = 0xF1
MISO/MOSI (out)
set by hardware
cleared by software
TXE flag
Tx buffer
(write to SPI_DR)
DATA 3 = 0xF3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
0xF1
BSY flag
set by hardware
cleared by software
0xF2
0xF3
reset by hardware
set by cleared by software
DATA 2 = 0xA2
DATA 1 = 0xA1
MISO/MOSI (in)
RXNE flag
Rx buffer
(read from SPI_DR)
software
software waits
writes 0xF1 until TXE=1 and
into SPI_DR writes 0xF2 into
SPI_DR
set by hardware
DATA 3 = 0xA3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
set by hardware
cleared by software
0xA1
software waits
software waits software waits
until RXNE=1 until TXE=1 and until RXNE=1
and reads 0xA1 writes 0xF3 into and reads 0xA2
from SPI_DR
SPI_DR
from SPI_ DR
0xA2
0xA3
software waits
until RXNE=1
and reads 0xA3
from SPI_DR
ai17344
550/713
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
Transmit-only procedure (BIDIMODE=0 RXONLY=0)
In this mode, the procedure can be reduced as described below and the BSY bit can be
used to wait until the completion of the transmission (see Figure 227 and Figure 228).
1.
Enable the SPI by setting the SPE bit to 1.
2.
Write the first data item to send into the SPI_DR register (this clears the TXE bit).
3.
Wait until TXE=1 and write the next data item to be transmitted. Repeat this step for
each data item to be transmitted.
4.
After writing the last data item into the SPI_DR register, wait until TXE=1, then wait until
BSY=0, this indicates that the transmission of the last data is complete.
This procedure can be also implemented using dedicated interrupt subroutines launched at
each rising edge of the TXE flag.
Note:
During discontinuous communications, there is a 2 APB clock period delay between the
write operation to SPI_DR and the BSY bit setting. As a consequence, in transmit-only
mode, it is mandatory to wait first until TXE is set and then until BSY is cleared after writing
the last data.
After transmitting two data items in transmit-only mode, the OVR flag is set in the SPI_SR
register since the received data are never read.
Figure 227. TXE/BSY behavior in Master transmit-only mode (BIDIMODE=0 and RXONLY=0)
in case of continuous transfers
Example in Master mode with CPOL=1, CPHA=1
SCK
DATA 2 = 0xF2
DATA 1 = 0xF1
MISO/MOSI (out)
set by hardware
cleared by software
TXE flag
Tx buffer
(write to SPI_DR)
BSY flag
software writes
0xF1 into
SPI_DR
DATA 3 = 0xF3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
0xF1
set by hardware
cleared by software
0xF2
0xF3
reset by hardware
set by hardware
software waits
software waits
until TXE=1 and until TXE=1 and
writes 0xF2 into writes 0xF3 into
SPI_DR
SPI_DR
set by hardware
software waits until TXE=1
software waits until BSY=0
ai17345
Doc ID16188 Rev 5
551/713
568
Serial peripheral interface (SPI)
RM0041
Figure 228. TXE/BSY in Slave transmit-only mode (BIDIMODE=0 and RXONLY=0) in case of
continuous transfers
Example in slave mode with CPOL=1, CPHA=1
SCK
DATA 1 = 0xF1
MISO/MOSI (out)
set by hardware
cleared by software
TXE flag
Tx buffer
(write to SPI_DR)
BSY flag
software writes
0xF1 into
SPI_DR
DATA 2 = 0xF2
DATA 3 = 0xF3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
0xF1
set by hardware
cleared by software
0xF2
set by hardware
0xF3
set by hardware
software waits
until TXE=1 and
writes 0xF2 into
SPI_DR
reset by hardware
software waits
until TXE=1 and
writes 0xF3 into
SPI_DR
software waits until TXE=1
software waits until BSY=0
ai17346
Bidirectional transmit procedure (BIDIMODE=1 and BIDIOE=1)
In this mode, the procedure is similar to the procedure in Transmit-only mode except that
the BIDIMODE and BIDIOE bits both have to be set in the SPI_CR2 register before enabling
the SPI.
Unidirectional receive-only procedure (BIDIMODE=0 and RXONLY=1)
In this mode, the procedure can be reduced as described below (see Figure 229):
1.
2.
3.
Set the RXONLY bit in the SPI_CR2 register.
Enable the SPI by setting the SPE bit to 1:
a)
In master mode, this immediately activates the generation of the SCK clock, and
data are serially received until the SPI is disabled (SPE=0).
b)
In slave mode, data are received when the SPI master device drives NSS low and
generates the SCK clock.
Wait until RXNE=1 and read the SPI_DR register to get the received data (this clears
the RXNE bit). Repeat this operation for each data item to be received.
This procedure can also be implemented using dedicated interrupt subroutines launched at
each rising edge of the RXNE flag.
Note:
552/713
If it is required to disable the SPI after the last transfer, follow the recommendation
described in Section 21.3.8: Disabling the SPI on page 557.
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
Figure 229. RXNE behavior in receive-only mode (BIDIRMODE=0 and RXONLY=1)
in case of continuous transfers
Example with CPOL=1, CPHA=1, RXONLY=1
SCK
DATA 1 = 0xA1
MISO/MOSI (in)
RXNE flag
DATA 2 = 0xA2
DATA 3 = 0xA3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
set by hardware
Rx buffer
(read from SPI_DR)
cleared by software
0xA1
software waits until RXNE=1
and reads 0xA1 from SPI_DR
software waits until RXNE=1
and reads 0xA2 from SPI_DR
0xA2
0xA3
software waits until RXNE=1
and reads 0xA3 from SPI_DR
ai17347
Bidirectional receive procedure (BIDIMODE=1 and BIDIOE=0)
In this mode, the procedure is similar to the Receive-only mode procedure except that the
BIDIMODE bit has to be set and the BIDIOE bit cleared in the SPI_CR2 register before
enabling the SPI.
Continuous and discontinuous transfers
When transmitting data in master mode, if the software is fast enough to detect each rising
edge of TXE (or TXE interrupt) and to immediately write to the SPI_DR register before the
ongoing data transfer is complete, the communication is said to be continuous. In this case,
there is no discontinuity in the generation of the SPI clock between each data item and the
BSY bit is never cleared between each data transfer.
On the contrary, if the software is not fast enough, this can lead to some discontinuities in
the communication. In this case, the BSY bit is cleared between each data transmission
(see Figure 230).
In Master receive-only mode (RXONLY=1), the communication is always continuous and
the BSY flag is always read at 1.
In slave mode, the continuity of the communication is decided by the SPI master device. In
any case, even if the communication is continuous, the BSY flag goes low between each
transfer for a minimum duration of one SPI clock cycle (see Figure 228).
Doc ID16188 Rev 5
553/713
568
Serial peripheral interface (SPI)
RM0041
Figure 230. TXE/BSY behavior when transmitting (BIDIRMODE=0 and RXONLY=0)
in case of discontinuous transfers
Example with CPOL=1, CPHA=1
SCK
MOSI (out)
DATA 1 = 0xF1
b0 b1 b2 b3 b4 b5 b6 b7
DATA 2 = 0xF2
DATA 3 = 0xF3
b0 b1 b2 b3 b4 b5 b6 b7
b0 b1 b2 b3 b4 b5 b6 b7
TXE flag
Tx buffer
(write to SPI_DR)
0xF1
0xF2
0xF3
BSY flag
software writes 0xF1
into SPI_DR
software waits until TXE=1 but is
late to write 0xF2 into SPI_DR
software waits until TXE=1 but
is late to write 0xF3 into
SPI_DR
software waits
until TXE=1
software waits until BSY=0
ai17348
21.3.6
CRC calculation
A CRC calculator has been implemented for communication reliability. Separate CRC
calculators are implemented for transmitted data and received data. The CRC is calculated
using a programmable polynomial serially on each bit. It is calculated on the sampling clock
edge defined by the CPHA and CPOL bits in the SPI_CR1 register.
Note:
This SPI offers two kinds of CRC calculation standard which depend directly on the data
frame format selected for the transmission and/or reception: 8-bit data (CR8) and 16-bit data
(CRC16).
CRC calculation is enabled by setting the CRCEN bit in the SPI_CR1 register. This action
resets the CRC registers (SPI_RXCRCR and SPI_TXCRCR). In full duplex or transmitter
only mode, when the transfers are managed by the software (CPU mode), it is necessary to
write the bit CRCNEXT immediately after the last data to be transferred is written to the
SPI_DR. At the end of this last data transfer, the SPI_TXCRCR value is transmitted.
In receive only mode and when the transfers are managed by software (CPU mode), it is
necessary to write the CRCNEXT bit after the second last data has been received. The CRC
is received just after the last data reception and the CRC check is then performed.
At the end of data and CRC transfers, the CRCERR flag in the SPI_SR register is set if
corruption occurs during the transfer.
If data are present in the TX buffer, the CRC value is transmitted only after the transmission
of the data byte. During CRC transmission, the CRC calculator is switched off and the
register value remains unchanged.
SPI communication using the CRC is possible through the following procedure:
554/713
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
1.
Program the CPOL, CPHA, LSBFirst, BR, SSM, SSI and MSTR values.
2.
Program the polynomial in the SPI_CRCPR register.
3.
Enable the CRC calculation by setting the CRCEN bit in the SPI_CR1 register. This
also clears the SPI_RXCRCR and SPI_TXCRCR registers.
4.
Enable the SPI by setting the SPE bit in the SPI_CR1 register.
5.
Start the communication and sustain the communication until all but one byte or halfword have been transmitted or received.
6.
Note:
–
In full duplex or transmitter-only mode, when the transfers are managed by
software, when writing the last byte or half word to the Tx buffer, set the
CRCNEXT bit in the SPI_CR1 register to indicate that the CRC will be transmitted
after the transmission of the last byte.
–
In receiver only mode, set the bit CRCNEXT just after the reception of the second
to last data to prepare the SPI to enter in CRC Phase at the end of the reception of
the last data. CRC calculation is frozen during the CRC transfer.
After the transfer of the last byte or half word, the SPI enters the CRC transfer and
check phase. In full duplex mode or receiver-only mode, the received CRC is
compared to the SPI_RXCRCR value. If the value does not match, the CRCERR flag in
SPI_SR is set and an interrupt can be generated when the ERRIE bit in the SPI_CR2
register is set.
When the SPI is in slave mode, be careful to enable CRC calculation only when the clock is
stable, that is, when the clock is in the steady state. If not, a wrong CRC calculation may be
done. In fact, the CRC is sensitive to the SCK slave input clock as soon as CRCEN is set,
and this, whatever the value of the SPE bit.
With high bitrate frequencies, be careful when transmitting the CRC. As the number of used
CPU cycles has to be as low as possible in the CRC transfer phase, it is forbidden to call
software functions in the CRC transmission sequence to avoid errors in the last data and
CRC reception. In fact, CRCNEXT bit has to be written before the end of the
transmission/reception of the last data.
For high bit rate frequencies, it is advised to use the DMA mode to avoid the degradation of
the SPI speed performance due to CPU accesses impacting the SPI bandwidth.
When the devices are configured as slaves and the NSS hardware mode is used, the NSS
pin needs to be kept low between the data phase and the CRC phase.
When the SPI is configured in slave mode with the CRC feature enabled, CRC calculation
takes place even if a high level is applied on the NSS pin. This may happen for example in
case of a multislave environment where the communication master addresses slaves
alternately.
Between a slave deselection (high level on NSS) and a new slave selection (low level on
NSS), the CRC value should be cleared on both master and slave sides in order to
resynchronize the master and slave for their respective CRC calculation.
To clear the CRC, follow the procedure below:
1.
Disable SPI (SPE = 0)
2.
Clear the CRCEN bit
3.
Set the CRCEN bit
4.
Enable the SPI (SPE = 1)
Doc ID16188 Rev 5
555/713
568
Serial peripheral interface (SPI)
21.3.7
RM0041
Status flags
Four status flags are provided for the application to completely monitor the state of the SPI
bus.
Tx buffer empty flag (TXE)
When it is set, this flag indicates that the Tx buffer is empty and the next data to be
transmitted can be loaded into the buffer. The TXE flag is cleared when writing to the
SPI_DR register.
Rx buffer not empty (RXNE)
When set, this flag indicates that there are valid received data in the Rx buffer. It is cleared
when SPI_DR is read.
BUSY flag
This BSY flag is set and cleared by hardware (writing to this flag has no effect). The BSY
flag indicates the state of the communication layer of the SPI.
When BSY is set, it indicates that the SPI is busy communicating. There is one exception in
master mode / bidirectional receive mode (MSTR=1 and BDM=1 and BDOE=0) where the
BSY flag is kept low during reception.
The BSY flag is useful to detect the end of a transfer if the software wants to disable the SPI
and enter Halt mode (or disable the peripheral clock). This avoids corrupting the last
transfer. For this, the procedure described below must be strictly respected.
The BSY flag is also useful to avoid write collisions in a multimaster system.
The BSY flag is set when a transfer starts, with the exception of master mode / bidirectional
receive mode (MSTR=1 and BDM=1 and BDOE=0).
It is cleared:
•
when a transfer is finished (except in master mode if the communication is continuous)
•
when the SPI is disabled
•
when a master mode fault occurs (MODF=1)
When communication is not continuous, the BSY flag is low between each communication.
When communication is continuous:
Note:
556/713
•
in master mode, the BSY flag is kept high during all the transfers
•
in slave mode, the BSY flag goes low for one SPI clock cycle between each transfer
Do not use the BSY flag to handle each data transmission or reception. It is better to use the
TXE and RXNE flags instead.
Doc ID16188 Rev 5
RM0041
21.3.8
Serial peripheral interface (SPI)
Disabling the SPI
When a transfer is terminated, the application can stop the communication by disabling the
SPI peripheral. This is done by clearing the SPE bit.
For some configurations, disabling the SPI and entering the Halt mode while a transfer is
ongoing can cause the current transfer to be corrupted and/or the BSY flag might become
unreliable.
To avoid any of those effects, it is recommended to respect the following procedure when
disabling the SPI:
In master or slave full-duplex mode (BIDIMODE=0, RXONLY=0)
1.
Wait until RXNE=1 to receive the last data
2.
Wait until TXE=1
3.
Then wait until BSY=0
4.
Disable the SPI (SPE=0) and, eventually, enter the Halt mode (or disable the peripheral
clock)
In master or slave unidirectional transmit-only mode (BIDIMODE=0,
RXONLY=0) or bidirectional transmit mode (BIDIMODE=1, BIDIOE=1)
After the last data is written into the SPI_DR register:
1.
Wait until TXE=1
2.
Then wait until BSY=0
3.
Disable the SPI (SPE=0) and, eventually, enter the Halt mode (or disable the peripheral
clock)
In master unidirectional receive-only mode (MSTR=1, BIDIMODE=0,
RXONLY=1) or bidirectional receive mode (MSTR=1, BIDIMODE=1, BIDIOE=0)
This case must be managed in a particular way to ensure that the SPI does not initiate a
new transfer:
Note:
1.
Wait for the second to last occurrence of RXNE=1 (n–1)
2.
Then wait for one SPI clock cycle (using a software loop) before disabling the SPI
(SPE=0)
3.
Then wait for the last RXNE=1 before entering the Halt mode (or disabling the
peripheral clock)
In master bidirectional receive mode (MSTR=1 and BDM=1 and BDOE=0), the BSY flag is
kept low during transfers.
In slave receive-only mode (MSTR=0, BIDIMODE=0, RXONLY=1) or
bidirectional receive mode (MSTR=0, BIDIMODE=1, BIDOE=0)
1.
You can disable the SPI (write SPE=1) at any time: the current transfer will complete
before the SPI is effectively disabled
2.
Then, if you want to enter the Halt mode, you must first wait until BSY = 0 before
entering the Halt mode (or disabling the peripheral clock).
Doc ID16188 Rev 5
557/713
568
Serial peripheral interface (SPI)
21.3.9
RM0041
SPI communication using DMA (direct memory addressing)
To operate at its maximum speed, the SPI needs to be fed with the data for transmission
and the data received on the Rx buffer should be read to avoid overrun. To facilitate the
transfers, the SPI features a DMA capability implementing a simple request/acknowledge
protocol.
A DMA access is requested when the enable bit in the SPI_CR2 register is enabled.
Separate requests must be issued to the Tx and Rx buffers (see Figure 231 and
Figure 232):
•
In transmission, a DMA request is issued each time TXE is set to 1. The DMA then
writes to the SPI_DR register (this clears the TXE flag).
•
In reception, a DMA request is issued each time RXNE is set to 1. The DMA then reads
the SPI_DR register (this clears the RXNE flag).
When the SPI is used only to transmit data, it is possible to enable only the SPI Tx DMA
channel. In this case, the OVR flag is set because the data received are not read.
When the SPI is used only to receive data, it is possible to enable only the SPI Rx DMA
channel.
In transmission mode, when the DMA has written all the data to be transmitted (flag TCIF is
set in the DMA_ISR register), the BSY flag can be monitored to ensure that the SPI
communication is complete. This is required to avoid corrupting the last transmission before
disabling the SPI or entering the Stop mode. The software must first wait until TXE=1 and
then until BSY=0.
Note:
558/713
During discontinuous communications, there is a 2 APB clock period delay between the
write operation to SPI_DR and the BSY bit setting. As a consequence, it is mandatory to
wait first until TXE=1 and then until BSY=0 after writing the last data.
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
Figure 231. Transmission using DMA
Example with CPOL=1, CPHA=1
SCK
DATA 2 = 0xF2
DATA 1 = 0xF1
DATA 3 = 0xF3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
MISO/MOSI (out)
set by hardware
set by hardware
cleared by DMA write
clear by DMA write
TXE flag
BSY flag
set by hardware
reset
by hardware
set by hardware
ignored by the DMA because
DMA transfer is complete
DMA request
Tx buffer
(write to SPI_DR)
0xF1
0xF2
0xF3
DMA writes to SPI_DR
set by hardware
DMA TCIF flag
(DMA transfer complete)
software configures the
DMA SPI Tx channel
to send 3 data items
and enables the SPI
DMA writes
DATA1 into
SPI_DR
DMA writes
DATA2 into
SPI_DR
clear by software
DMA writes
DMA transfer is
DATA3 into complete (TCIF=1 in
SPI_DR
DMA_ISR)
software waits
until TXE=1
software waits until BSY=0
ai17349
Figure 232. Reception using DMA
Example with CPOL=1, CPHA=1
SCK
DATA 1 = 0xA1
MISO/MOSI (in)
RXNE flag
DATA 2 = 0xA2
DATA 3 = 0xA3
b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 b7
set by hardware
clear by DMA read
DMA request
Rx buffer
(read from SPI_DR)
0xA1
0xA2
0xA3
DMA read from SPI_DR
set by hardware
flag DMA TCIF
(DMA transfer complete)
software configures the
DMA SPI Rx channel
to receive 3 data items
and enables the SPI
DMA reads
DATA1 from
SPI_DR
DMA reads
DATA2 from
SPI_DR
DMA reads
DATA3 from
SPI_DR
clear
by software
The DMA transfer is
complete (TCIF=1 in
DMA_ISR)
ai17350
Doc ID16188 Rev 5
559/713
568
Serial peripheral interface (SPI)
RM0041
DMA capability with CRC
When SPI communication is enabled with CRC communication and DMA mode, the
transmission and reception of the CRC at the end of communication are automatic that is
without using the bit CRCNEXT. After the CRC reception, the CRC must be read in the
SPI_DR register to clear the RXNE flag.
At the end of data and CRC transfers, the CRCERR flag in SPI_SR is set if corruption
occurs during the transfer.
21.3.10
Error flags
Master mode fault (MODF)
Master mode fault occurs when the master device has its NSS pin pulled low (in NSS
hardware mode) or SSI bit low (in NSS software mode), this automatically sets the MODF
bit. Master mode fault affects the SPI peripheral in the following ways:
•
The MODF bit is set and an SPI interrupt is generated if the ERRIE bit is set.
•
The SPE bit is cleared. This blocks all output from the device and disables the SPI
interface.
•
The MSTR bit is cleared, thus forcing the device into slave mode.
Use the following software sequence to clear the MODF bit:
1.
Make a read or write access to the SPI_SR register while the MODF bit is set.
2.
Then write to the SPI_CR1 register.
To avoid any multiple slave conflicts in a system comprising several MCUs, the NSS pin
must be pulled high during the MODF bit clearing sequence. The SPE and MSTR bits can
be restored to their original state after this clearing sequence.
As a security, hardware does not allow the setting of the SPE and MSTR bits while the
MODF bit is set.
In a slave device the MODF bit cannot be set. However, in a multimaster configuration, the
device can be in slave mode with this MODF bit set. In this case, the MODF bit indicates
that there might have been a multimaster conflict for system control. An interrupt routine can
be used to recover cleanly from this state by performing a reset or returning to a default
state.
Overrun condition
An overrun condition occurs when the master device has sent data bytes and the slave
device has not cleared the RXNE bit resulting from the previous data byte transmitted.
When an overrun condition occurs:
•
the OVR bit is set and an interrupt is generated if the ERRIE bit is set.
In this case, the receiver buffer contents will not be updated with the newly received data
from the master device. A read from the SPI_DR register returns this byte. All other
subsequently transmitted bytes are lost.
Clearing the OVR bit is done by a read from the SPI_DR register followed by a read access
to the SPI_SR register.
560/713
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
CRC error
This flag is used to verify the validity of the value received when the CRCEN bit in the
SPI_CR1 register is set. The CRCERR flag in the SPI_SR register is set if the value
received in the shift register does not match the receiver SPI_RXCRCR value.
21.3.11
SPI interrupts
Table 119. SPI interrupt requests
Interrupt event
Event flag
Enable Control bit
TXE
TXEIE
Receive buffer not empty flag
RXNE
RXNEIE
Master Mode fault event
MODF
Transmit buffer empty flag
Overrun error
OVR
CRC error flag
CRCERR
Doc ID16188 Rev 5
ERRIE
561/713
568
Serial peripheral interface (SPI)
21.4
RM0041
SPI registers
Refer to Section: List of abbreviations for registers.
The peripheral registers have to be accessed by half-words (16 bits) or words (32 bits).
21.4.1
SPI control register 1 (SPI_CR1)
Address offset: 0x00
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
BIDI
MODE
BIDI
OE
CRC
EN
CRC
NEXT
DFF
RX
ONLY
SSM
SSI
LSB
FIRST
SPE
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
5
4
3
BR [2:0]
rw
rw
rw
2
1
0
MSTR
CPOL
CPHA
rw
rw
rw
Bit 15 BIDIMODE: Bidirectional data mode enable
0: 2-line unidirectional data mode selected
1: 1-line bidirectional data mode selected
Bit 14 BIDIOE: Output enable in bidirectional mode
This bit combined with the BIDImode bit selects the direction of transfer in bidirectional mode
0: Output disabled (receive-only mode)
1: Output enabled (transmit-only mode)
Note: In master mode, the MOSI pin is used and in slave mode, the MISO pin is used.
Bit 13 CRCEN: Hardware CRC calculation enable
0: CRC calculation disabled
1: CRC calculation Enabled
Note: This bit should be written only when SPI is disabled (SPE = ‘0) for correct operation
Bit 12 CRCNEXT: CRC transfer next
0: Data phase (no CRC phase)
1: Next transfer is CRC (CRC phase)
Note: When the SPI is configured in full duplex or transmitter only modes, CRCNEXT must be
written as soon as the last data is written to the SPI_DR register.
When the SPI is configured in receiver only mode, CRCNEXT must be set after the
second last data reception.
This bit should be kept cleared when the transfers are managed by DMA.
Bit 11 DFF: Data frame format
0: 8-bit data frame format is selected for transmission/reception
1: 16-bit data frame format is selected for transmission/reception
Note: This bit should be written only when SPI is disabled (SPE = ‘0) for correct operation
Bit 10 RXONLY: Receive only
This bit combined with the BIDImode bit selects the direction of transfer in 2-line
unidirectional mode. This bit is also useful in a multislave system in which this particular
slave is not accessed, the output from the accessed slave is not corrupted.
0: Full duplex (Transmit and receive)
1: Output disabled (Receive-only mode)
562/713
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
Bit 9 SSM: Software slave management
When the SSM bit is set, the NSS pin input is replaced with the value from the SSI bit.
0: Software slave management disabled
1: Software slave management enabled
Bit 8 SSI: Internal slave select
This bit has an effect only when the SSM bit is set. The value of this bit is forced onto the
NSS pin and the IO value of the NSS pin is ignored.
Bit 7 LSBFIRST: Frame format
0: MSB transmitted first
1: LSB transmitted first
Note: This bit should not be changed when communication is ongoing.
Bit 6 SPE: SPI enable
0: Peripheral disabled
1: Peripheral enabled
Note: When disabling the SPI, follow the procedure described in Section 21.3.8: Disabling the
SPI.
Bits 5:3 BR[2:0]: Baud rate control
000: fPCLK/2
001: fPCLK/4
010: fPCLK/8
011: fPCLK/16
100: fPCLK/32
101: fPCLK/64
110: fPCLK/128
111: fPCLK/256
Note: These bits should not be changed when communication is ongoing.
Bit 2 MSTR: Master selection
0: Slave configuration
1: Master configuration
Note: This bit should not be changed when communication is ongoing.
Bit1 CPOL: Clock polarity
0: CK to 0 when idle
1: CK to 1 when idle
Note: This bit should not be changed when communication is ongoing.
Bit 0 CPHA: Clock phase
0: The first clock transition is the first data capture edge
1: The second clock transition is the first data capture edge
Note: This bit should not be changed when communication is ongoing.
21.4.2
SPI control register 2 (SPI_CR2)
Address offset: 0x04
Reset value: 0x0000
15
14
13
12
11
Reserved
10
9
8
7
6
5
TXEIE RXNEIE ERRIE
rw
rw
Doc ID16188 Rev 5
rw
4
3
2
Res.
Res.
SSOE
rw
1
0
TXDMAEN RXDMAEN
rw
rw
563/713
568
Serial peripheral interface (SPI)
RM0041
Bits 15:8 Reserved, must be kept at reset value.
Bit 7 TXEIE: Tx buffer empty interrupt enable
0: TXE interrupt masked
1: TXE interrupt not masked. Used to generate an interrupt request when the TXE flag is set.
Bit 6 RXNEIE: RX buffer not empty interrupt enable
0: RXNE interrupt masked
1: RXNE interrupt not masked. Used to generate an interrupt request when the RXNE flag is
set.
Bit 5 ERRIE: Error interrupt enable
This bit controls the generation of an interrupt when an error condition occurs ).
0: Error interrupt is masked
1: Error interrupt is enabled
Bits 4:3 Reserved, must be kept at reset value.
Bit 2 SSOE: SS output enable
0: SS output is disabled in master mode and the cell can work in multimaster configuration
1: SS output is enabled in master mode and when the cell is enabled. The cell cannot work
in a multimaster environment.
Bit 1 TXDMAEN: Tx buffer DMA enable
When this bit is set, the DMA request is made whenever the TXE flag is set.
0: Tx buffer DMA disabled
1: Tx buffer DMA enabled
Bit 0 RXDMAEN: Rx buffer DMA enable
When this bit is set, the DMA request is made whenever the RXNE flag is set.
0: Rx buffer DMA disabled
1: Rx buffer DMA enabled
21.4.3
SPI status register (SPI_SR)
Address offset: 0x08
Reset value: 0x0002
15
14
13
12
11
Reserved
10
9
8
7
6
5
4
BSY
OVR
MODF
CRC
ERR
r
r
r
rc_w0
3
2
Reserved
1
0
TXE
RXNE
r
r
Bits 15:8 Reserved, must be kept at reset value.
Bit 7 BSY: Busy flag
0: SPI not busy
1: SPIis busy in communication or Tx buffer is not empty
This flag is set and cleared by hardware.
Note: BSY flag must be used with caution: refer to Section 21.3.7: Status flags and
Section 21.3.8: Disabling the SPI.
Bit 6 OVR: Overrun flag
0: No overrun occurred
1: Overrun occurred
This flag is set by hardware and reset by a software sequence.
564/713
Doc ID16188 Rev 5
RM0041
Serial peripheral interface (SPI)
Bit 5 MODF: Mode fault
0: No mode fault occurred
1: Mode fault occurred
This flag is set by hardware and reset by a software sequence. Refer to Section 21.3.10 on
page 560 for the software sequence.
Bit 4 CRCERR: CRC error flag
0: CRC value received matches the SPI_RXCRCR value
1: CRC value received does not match the SPI_RXCRCR value
This flag is set by hardware and cleared by software writing 0.
Bits 3:2
Reserved
Bit 1 TXE: Transmit buffer empty
0: Tx buffer not empty
1: Tx buffer empty
Bit 0 RXNE: Receive buffer not empty
0: Rx buffer empty
1: Rx buffer not empty
21.4.4
SPI data register (SPI_DR)
Address offset: 0x0C
Reset value: 0x0000
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
rw
rw
rw
rw
rw
rw
rw
DR[15:0]
rw
rw
rw
rw
rw
rw
rw
rw
rw
Bits 15:0 DR[15:0]: Data register
Data received or to be transmitted.
The data register is split into 2 buffers - one for writing (Transmit Buffer) and another one for
reading (Receive buffer). A write to the data register will w">