Fuji Xerox DocuPrint 205, 255, 305 printer User Guide

DocuPrint 205/255/305
User Guide
Adobe, the Adobe logo, PostScript, PostScript 3 and the PostScript logo are trademarks of Adobe Systems
Incorporated.
Microsoft, Windows, Windows NT, Windows Server are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Permission has been obtained from Microsoft Corporation for use of software screen shots.
PCL, HP, HP-GL, HP-GL/2 and HP-UX are registered trademarks of Hewlett-Packard Corporation.
Netware is a registered trademark of Novell, Inc., in the United States and other countries.
Macintosh, MacOS, AppleTalk, EtherTalk and TrueType are trademarks of Apple Computer, Inc., registered in the
U.S. and other countries.
Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United
States and other countries.
UNIX is a registered trademark of the Open Group in the United States and other countries.
Solaris, SunOS and NIS (Network Information Services) are trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and other countries.
This product is equipped with the RSA® BSAFE™ Crypto-C of RSA Security Inc.
RSA is a registered trademark of RAS Security Inc. BSAFE is a registered trademark of RSA Security Inc. in the
United States and other countries.
RSA Security Inc. All rights reserved.
All product/brand names are trademarks or registered trademarks of the respective holders.
As a member of the International Energy Star Program, Fuji Xerox confirms this product
satisfies the requirements for International Energy Star Program standards.
Data Loss in Hard Disk
Saved data may be lost if hard disk of the machine breaks down due to external shocks or if the power is
accidentally cut off in a manner not following the methods listed in manuals or other documentations. Fuji
Xerox is not responsible for such data loss and any consequence caused by such data loss.
Damage related to computer virus
Fuji Xerox is not responsible for any breakdown of machines due to infection of computer virus.
Important
c This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied
or modified in whole or part, without the written consent of the publisher.
d Parts of this manual are subject to change without prior notice.
e We welcome any comments on ambiguities, errors, omissions, or missing pages.
f Never attempt any procedure on the machine that is not specifically described in this manual. Unauthorized
operation can cause faults or accidents. Fuji Xerox is not liable for any problems resulting from unauthorized
operation of the equipment.
Xerox, The Document Company and the stylized X are registered trademarks of Xerox Corporation.
All Xerox and Fuji Xerox product names are either registered trademarks or trademarks of Xerox Corporation and
Fuji Xerox Co., Ltd.
Preface
Thank you for choosing this printer. This is a guide on operating this printer and the
important points to note. To understand the features fully and to use the machine correctly
and effectively, please read this guide before using it.
Keep this guide handy for a quick reference on using the machine. The illustrations used in
this guide are based on DocuPrint 255/305.
This guide is written with the assumption that you are familiar with the basic knowledge and
way of operating your computer environment and the network environment.
In this manual, safety instructions are preceded by with the symbol
.
Always read and follow these instructions before performing the required procedures.
This product is a “Class I Laser System” that does not emit dangerous laser beam. Operate the machine
according to the instructions in the manual. Do not carry out any operation not mentioned in the manual.
Otherwise, it may lead to unforeseen accident or machine breakdown.
Fuji Xerox shares the global concern about environmental conservation and has integrated that concern
in its business activities - from research and development to disposal. We have implemented a number
of programs to lessen the burden on the environment. For example, we have totally eliminated
ozone-depleting chlorofluorocarbons from our manufacturing facilities.
We are committed to leadership in the conservation of resources by reusing and recycling post-consumer
waste material such as paper, cartridges, and parts from our customer’s copiers and printers. Along with
our efforts to make environmental values a part of the Fuji Xerox culture, DocuPrint 205/255/305 adopts
recycled components that satisfy our strict quality standards
Reception interference
When installed at a certain location, the machine may cause interference with radio and television
reception. If you notice flickering or distorted images or noises on your audio-visual units, your machine
may be causing radio interference.
Switch it off, and if the interference disappears, the machine is the cause of radio interference. Perform
the following procedure until the interference is corrected.
• Move the machine and the TV and/or radio away from each other.
• Reposition or reorientate the machine and TV and/or radio.
• Unplug the machine, TV and/or radio, and replug them into outlets that operate on different circuits.
• Reorientate the TV and/or radio antennas and cables until the interference stops. For an outdoor
antenna, ask your local electrician for support.
• Use coaxial cable antennas.
Preface
3
Conventions
1.
In this guide, “computer” refers to both the personal computer and workstation.
2.
The following icons are used in this guide:
3.
4
Conventions
Important
Indicates important information which you should read.
Note
Indicates additional information on operations or features.
Refer to
Indicates reference sources.
The following conventions are used in this guide:
Refer to “xxx”
: The cross-reference is within this guide.
Refer to xxx
: The cross-reference is not within this guide.
[
]
: Indicates items displayed on the computer and the printer control
panel. Also indicates the title of printed reports/lists from the printer.
<
>
: Indicates items such as hard buttons and indicators on the keyboard
and printer.
Types of Manuals
Manuals Bundled With the Machine & Their Contents
Setup and Quick Reference Guide
Explains the way of installation, loading paper, and troubleshooting
of this printer.
The Online Help for the
CentreWare Internet Services
Explains how to set the items and features of CentreWare Internet
Services.
The Online Help for the printer
driver
Explains how to set the items and features of the printer driver.
User Guide (PDF)
Explains printer settings, and describes control panel menu items
and daily care in detail.
This PDF file is included in the CD-ROM bundled with this printer.
Network Print Environment User
Guide (PDF)
Explains how to set the printer for the network environment to use
this printer as a network printer.
This PDF file is included in the CD-ROM bundled with this printer.
HP-GL, HP-GL/2 Emulation
Settings Guide (PDF)
Explains how to set the emulation mode for HP-GL and HP-GL/2.
This PDF file is included in the CD-ROM bundled with this printer.
Manuals Bundled With Optional Accessories
User Guide (PostScript® Software
Kit) (PDF)
Explains the way of setting the printer as a PostScript printer and
the items that can be set in the printer driver.
This PDF file is included in the CD-ROM bundled with the
PostScript software kit.
Installation Guide
Explains the installation procedure of each optional accessory.
Note
• Adobe® Acrobat® Reader needs to be installed to display PDF files.
Types of Manuals
5
Contents
Preface.............................................................................................................. 3
Conventions ...................................................................................................... 4
Types of Manuals.............................................................................................. 5
Contents............................................................................................................ 6
Contents of the Setup and Quick Reference Guide (Reference)...................... 9
The Objective of the International Energy Star Program ................................ 10
Illegal Copies and Printouts ............................................................................ 11
1
Basic Operations ...................................................................................... 12
1.1
1.2
1.3
1.4
1.5
2
Printing ..................................................................................................... 21
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
6
Contents
Main Components and Their Functions................................................................. 12
Main Body ..............................................................................................................12
Control Panel .........................................................................................................15
Display ...................................................................................................................16
Switching On and Off the Power ........................................................................... 17
Switching On the Power ........................................................................................17
Switching Off the Power ........................................................................................17
Power Saver Modes .............................................................................................. 18
Canceling/Checking Printing ................................................................................. 18
Canceling Printing .................................................................................................18
Checking Status of Print Data ...............................................................................19
Displaying Optional Accessory Configuration and Paper Tray Settings................ 20
Printing From the Computer .................................................................................. 21
Printing on Envelopes............................................................................................ 22
Loading Envelopes ................................................................................................22
Printing on Envelopes ............................................................................................23
Printing on Transparencies.................................................................................... 25
Loading Transparencies ........................................................................................25
Printing on Transparencies ....................................................................................25
Printing on Custom Size Paper/Long Paper.......................................................... 27
Loading Custom Size Paper ..................................................................................27
Setting Custom Paper Sizes ..................................................................................29
Printing on Custom Size Paper .............................................................................30
Print Confidential Document - Secure Print........................................................... 32
About Secure Print ................................................................................................32
Configuring Secure Print .......................................................................................32
Print After Checking Printing Result - Sample Print .............................................. 35
About Sample Print ................................................................................................35
Configuring Sample Print .......................................................................................35
Print at a Specified Time - Delayed Print............................................................... 38
Registering Delayed Print ......................................................................................38
Canceling Delayed Print ........................................................................................39
Direct Printing of PDF File ..................................................................................... 40
Using ContentsBridge Utility to Print PDF .............................................................41
Printing a PDF File Without Using ContentsBridge Utility .....................................47
Printing From Web Browser .................................................................................. 48
Printing via E-mail - E-mail Printing ....................................................................... 50
Environment Settings for E-mail Printing ...............................................................50
Sending E-mails ....................................................................................................53
Receiving and Printing E-mails .............................................................................. 53
Points to Note When Sending E-mails ..................................................................54
3
About Paper ............................................................................................. 55
3.1
3.2
3.3
3.4
4
Settings on the Control Panel................................................................... 65
4.1
4.2
4.3
5
5.5
5.6
When Paper Jams ............................................................................................... 101
When Problems Occur ........................................................................................ 104
When the Print Quality Is Poor ............................................................................ 108
Message List ....................................................................................................... 111
Message List (Alphabetical Order) .....................................................................111
List of Error Codes ...............................................................................................115
Network Related Troubles ................................................................................... 120
Using TCP/IP .......................................................................................................120
Using CentreWare Internet Services ...................................................................121
Mail Related Troubles.......................................................................................... 123
Daily Care............................................................................................... 124
6.1
6.2
6.3
6.4
6.5
6.6
6.7
A
Overview of the Common Menu ............................................................................ 65
Menu Configuration ...............................................................................................65
Changing Menu Settings .......................................................................................67
Description of Menu Items..................................................................................... 71
Print Language ......................................................................................................71
Admin Menu ..........................................................................................................76
Menu List ............................................................................................................... 96
Troubleshooting...................................................................................... 101
5.1
5.2
5.3
5.4
6
About Paper........................................................................................................... 55
Usable Paper .........................................................................................................55
Unusable Paper .....................................................................................................58
Storing and Handling Paper ..................................................................................58
Loading Paper ....................................................................................................... 59
Loading Paper in a Paper Tray .............................................................................. 59
Loading Paper in the Bypass Tray (Optional) ........................................................61
Automatic Tray Selection .......................................................................................62
Setting Custom Paper Sizes.................................................................................. 63
Setting Paper Types .............................................................................................. 64
Replacing the Drum/Toner Cartridge................................................................... 124
Printing Reports/Lists .......................................................................................... 127
Types of Reports/Lists .........................................................................................127
Printing Reports/Lists ..........................................................................................129
Checking/Managing the Printer Status on a Web Browser ................................. 130
Settings for CentreWare Internet Services ..........................................................130
Procedure ............................................................................................................132
IP Filter Feature via IP Address List ....................................................................133
Checking Printer Status via E-mail ...................................................................... 134
About Mail Notice Service ...................................................................................134
Settings for Mail Notice Service ...........................................................................134
Checking Printed Pages ...................................................................................... 137
Checking Total Printed Pages on Meter ..............................................................137
Checking Total Printed Pages on Print Meter Report ..........................................137
Cleaning the Printer............................................................................................. 139
When Moving the Printer ..................................................................................... 143
Appendix ................................................................................................ 144
A.1
A.2
Specifications ...................................................................................................... 144
Product Specifications .........................................................................................144
Printable Area ......................................................................................................147
Optional Accessories and Consumables............................................................. 148
Optional Accessories ...........................................................................................148
Consumables .......................................................................................................149
Contents
7
A.3
A.4
A.5
A.6
A.7
A.8
Life of Consumables and Regular Replacement Parts........................................ 150
How to Obtain Product Information ..................................................................... 151
Latest Printer Driver .............................................................................................151
Upgrading the Firmware Version of This Printer .................................................151
Output Size and Memory Capacity...................................................................... 152
Precautions and Limitations ................................................................................ 154
Precautions and Limitations of This Printer .........................................................154
TIFF File Format ..................................................................................................156
Printing Using the Serial Interface ....................................................................... 158
Settings on the Printer .........................................................................................158
Settings on the Printer Driver ..............................................................................159
Glossary .............................................................................................................. 160
Index ............................................................................................................. 165
8
Contents
Contents of the Setup and Quick Reference Guide (Reference)
Preface
Conventions
Types of Manuals
Features in Brief
Contents
Contents of the User Guide (Reference)
Safety Notes
1
Installing the Printer............................................................................ SQ-12
Checking the Package Contents, Unpacking the Printer
Installing the Optional Accessories
Installing the Drum/Toner Cartridge
Connecting Interface Cable
Connecting the Power Cord to Switch on the Printer
Loading Paper
Printing Reports/Lists
2
Setting the Printer Environment ......................................................... SQ-18
Supported Environment
Setting IP Address
Setting Printer Configurations via CentreWare Internet Services
Installing the Printer Driver
3
Basic Operations ................................................................................ SQ-27
Printing From the Computer
Switching On and Off the Power
Power Saver Modes
Canceling Printing
4
About Paper ....................................................................................... SQ-29
About Paper
Loading Paper
Setting Custom Paper Sizes
Setting Paper Types
5
List of Menu Items on the Control Panel ............................................ SQ-36
6
Troubleshooting.................................................................................. SQ-41
When Paper Jams
When Problems Occur
When the Print Quality Is Poor
Error Messages
A
Appendix ............................................................................................ SQ-55
Optional Accessories and Consumables
How to Obtain Product Information
Index
Contents of the Setup and Quick Reference Guide (Reference)
9
The Objective of the International Energy
Star Program
To protect the global environment and conserve energy sources, the International Energy
Star Program encourages the following product features. Fuji Xerox confirms DocuPrint
205/255/305 satisfies the requirements for this program.
Low Power Mode Feature
This product has a power-saving feature, which switches the machine to the low power
mode automatically if the machine is on and not operated for a certain period of time. In this
mode the machine stops power to the fuser and saves the power consumption. The default
low power mode start time is set at 5 minutes.
You can set the low power mode start time between 5 and 30 minutes in 1 minute intervals.
For details on how to set the time, refer to “System Settings” (P. 86).
Note
• The sleep mode feature in this machine saves further power consumption than the low power mode.
10
The Objective of the International Energy Star Program
Illegal Copies and Printouts
Copying or printing certain documents may be illegal in your country. Penalties of fines
or imprisonment may be imposed on those found guilty. The following are examples of
items that may be illegal to copy or print in your country.
‰
‰
‰
‰
‰
‰
Currency
Banknotes and checks
Bank and government bonds and securities
Passports and identification cards
Copyright material or trademarks without the consent of the owner
Postage stamps and other negotiable instruments
This list is not inclusive and no liability is assumed for either its completeness or
accuracy. In case of doubt, contact your legal counsel.
Illegal Copies and Printouts
11
1
Basic Operations
1.1
Main Components and Their Functions
Main Body
Standard Configuration
1
9
2
14
12
8
7 6 5
No.
12
4
3
15
13
3
3 10 11
Name
Description
1
Center output tray
Print jobs are output here with the printed side facing down.
2
Control panel
Consists of the essential operation buttons, indicators and
display.
3
Ventilation hole
Releases heat to prevent the interior of the printer from heating
up.
4
Paper meter
A meter to check the amount of remaining paper. Attached to the
550-sheet tray.
5
Tray 1
Sets the 150-sheet tray.
6
Tray 2
250-sheet tray is set for DocuPrint 205 and 550-sheet tray for
DocuPrint 255/305.
7
Paper size label
For the paper size label to indicate the paper size in the paper
tray.
8
Power switch
Switches the power of the printer on and off. Pressing the switch
to the < > position switches it on and pressing it to the <{>
position switches it off.
9
Extension output tray
Pull this out when printing on paper larger than A4 size.
10
Duplex unit connector
For connecting the duplex unit (optional).
11
Power cord connector
For connecting the power cord.
12
Parallel connector
For connecting the parallel cable.
13
Network connector
For connecting the network cable when connecting this printer to
the network for use.
14
USB connector
For connecting the USB cable.
15
Serial connector
For connecting the serial cable.
1 Basic Operations
With Optional Accessories
1
2
3
8
4
5
7
6
No.
Name
Description
1
Offset catch tray
Allows you to stagger the output position for each print job (offset
output). Can be installed to DocuPrint 255/305.
2
Cover D
Open this when paper is jammed inside the offset catch tray.
3
Rear tray
For reducing the curling of paper when printing heavyweight
paper. Print jobs are output here with the printed side facing up.
Can be installed to DocuPrint 255/305.
4
Duplex unit (Cover C)
Enables 2 sided printing. When paper is jammed inside the
duplex unit, it is described as cover C.
5
Rear output tray lever
When the rear tray (optional) has been installed, the paper
output location can be switched between it and the center output
tray. Raise the lever to output to the rear tray and lower the lever
to output to the center output tray.
6
A3 universal tray
Can install up to two levels of trays. There are two types of tray
modules available: 250 tray and 550 tray.
7
Right detachable cover
Remove this when installing optional accessories such as hard
disk and additional memory.
8
Bypass tray
By installing this tray instead of tray 1, you can feed paper using
this tray.
1.1 Main Components and Their Functions
13
Internal View
1
2
No.
14
3
Name
5
4
6
Description
1
Extension output tray
Pull this out when printing on paper larger than A4 size.
2
Drum/toner cartridge
Contains the toner and the photosensitive drum.
3
Cover A
Open this when replacing the drum/toner cartridge and removing
jammed paper.
4
Fuser unit
Fixes the toner on the paper. Do not touch this when using the
printer as it is hot.
5
Transfer roll cartridge
Transfers the toner image on the surface of the photosensitive
drum to the paper.
6
Cover B
Open this when removing jammed paper.
1 Basic Operations
Control Panel
1
2
3
5 4
6
9
8
No.
7
Name
Description
1
<Menu> button
Press to move to the menu operation.
2
<Eject/Set> button
Press to set the menu candidate values. Use this too to print
report/list.
3
<Ready> indicator
When the light is on, the printer is ready to receive data from the
computer.
4
LCD display
Displays the setting items, machine status, and messages.
Refer to
• “Display” (P. 16)
5
<Error> indicator
When the light is on, there is a malfunction in the printer.
6
<Power Saver> button/
indicator
Press to enter and exit the power saver mode. The light is on
when the machine is in the power saver mode.
7
<Cancel Job> button
Press to cancel printing.
8
<Online> button
Press to enter the offline status. When in the offline status, the
machine cannot receive data or process printing. Press again to
exit the offline status and enter the online status (where the
machine can receive data from the computer).
9
< ><
buttons
><
><
>
Press these to move to the required menu, item and candidate
value on the display. Also, press the < > button when you are
doing secure/sample/delayed printing or when you are checking/
printing received mails manually.
Note
• When you are changing the candidate values by the < > or
< > button, you can press and hold down the buttons to
change the display continuously. Also, pressing the < > and
< > buttons simultaneously will display the default values.
1.1 Main Components and Their Functions
15
Display
There are two types of screens shown: Print screen (for displaying printer status) and Menu
screen (for configuring settings).
Note
• The message displayed differs according to the optional accessories installed and setting status.
Print Screen
The Print screen appears when the printer is printing or waiting for data. The following
contents are shown on the screen.
Printer status
Port for receiving data
Feeding tray
Menu Screen
Screen for configuring settings related to the printer.
This screen appears when you press the <Menu> button. The initial Menu screen displayed
is as follows.
Refer to
• Items that can be set on the Menu screen: “4 Settings on the Control Panel” (P. 65)
16
1 Basic Operations
1.2
Switching On and Off the Power
Switching On the Power
1.
Press the power switch of the printer to the
< > position.
2.
When the power is on, “Please wait...” will
be displayed on the control panel. Check
that this display changes to “Ready to
print”.
Note
• When “Please wait...” is displayed, the printer is in the
process of warming up. Printing is unavailable during
this period. When the printer is ready for printing,
“Ready to print” will be displayed.
Important
• If error message is displayed, refer to “Message List (Alphabetical Order)” (P. 111) on how to fix it.
Switching Off the Power
Important
• Do not switch off the power of this printer when printing is in progress. It may lead to a paper jam.
• Once the power is switched off, print data remaining in this printer or information saved in the memory of
this printer will be deleted.
1.
By checking the display on the control
panel, confirm that the printer is not
processing any data.
2.
Press the power switch of this printer to the
< > position to switch off the power.
1.2 Switching On and Off the Power
17
1.3
Power Saver Modes
This printer is equipped with a low power mode and a sleep mode to reduce power
consumption when it is left idle.
When no print data is received for 5 minutes, the printer will enter the low power mode.
When no data is received for a further 10 minutes (a total of 15 minutes lapse (default
settings) since the last received data), it will enter sleep mode. You can specify whether the
printer goes into low power mode or sleep mode. The time ranges to specify for the printer
to go into low power mode or sleep mode are 5 to 30 minutes respectively. Consumption of
power during the sleep mode is 10 W or less (220 - 240 V) or 5 W or less (120 V) and the
time taken to exit from the sleep mode to a print-ready status is about 10 seconds.
Note
• You can enable either only the low power mode or the sleep mode.
• Both the low power mode and sleep mode cannot be disabled at the same time.
• For details on the low power/sleep mode and the procedure to change the settings, refer to “Example:
Changing the Low Power/Sleep Mode Settings” (P. 68).
• When the lower power mode and sleep mode are both enabled, the sleep mode setting is given priority.
For example, when 15 minutes is set for the sleep mode and 30 minutes is set for the low power mode,
the printer enters the sleep mode 15 minutes after the last data is received, and the sleep mode
continues even after an additional 15 minutes when the printer is programmed to enter the low power
mode.
Exiting the Power Saver Mode
The printer automatically cancels the power saver mode once it receives data from the
computer. This mode can also be canceled by pressing the <Power Saver> button on the
control panel.
1.4
Canceling/Checking Printing
Canceling Printing
To cancel printing, you can either cancel the print job at this printer or at the computer.
Canceling Printing of Data Being Printed or Received at the Printer
Press the <Cancel Job> button on the control panel. However, pages being printed at the
moment will continue to be printed.
Note
• You can also cancel printing on the [Jobs] screen of CentreWare Internet Services. For details, refer to
the Online Help for CentreWare Internet Services.
18
1 Basic Operations
Canceling Printing of All Print Data Received at the Printer
Press the <Online> button on the control panel, and the press the <Cancel Job> button.
Press the <Online> button again after the canceling process has been completed.
Canceling Print Data That Are Being Processed at the Computer
Double-click the printer icon
at the bottom right of the taskbar in Windows.
From the displayed window, click the document name that you wish to delete and press the
<Delete> key.
Checking Status of Print Data
Checking in Windows
Double-click the printer icon
on the task bar at the bottom right of the screen.
From the displayed window, check the column, [Status].
Checking in CentreWare Internet Services
You can check the status of the print job sent to the printer at the [Jobs] screen of
CentreWare Internet Services.
Refer to
• Online Help for CentreWare Internet Services
1.4 Canceling/Checking Printing
19
1.5
Displaying Optional Accessory
Configuration and Paper Tray Settings
When using this printer as a network printer and having enabled SNMP protocol, you can
display on the printer driver, the optional accessory configuration or settings configured at
the control panel such as paper type or size. These settings are displayed on the [Options]
tab. This section explains the procedure using Windows XP as an example.
Important
• When using this printer as a local printer, this feature cannot be used. You have to manually set the
items on the printer driver.
• The rear tray information cannot be obtained. You have to manually set the item.
• For paper size and paper type settings, you must configure them at the control panel beforehand. Even
if you change the settings here, they will not be reflected on the printer itself.
Note
• When using this feature, you have to activate the SNMP port (default: [Enable]) on the printer using the
control panel.
• For Windows NT 4.0/Windows 2000/Windows XP/Windows Server 2003, only users with administrator’s
rights can change the settings. Users without the rights can only check the contents.
1.
From the [Start] menu, click [Printers and Faxes] and then display the properties of the
printer to be used.
2.
Click the [Options] tab.
3.
Click [Get Information from Printer].
3
4
The data of the printer can be displayed on the printer driver.
4.
Click [OK]. The contents of the [Options] tab will be updated based on the data
obtained from the printer.
Note
• The automatically detected paper size and orientation will be displayed as the paper size and orientation
of [Paper Tray Attributes].
• The paper type set on the control panel will be displayed as the paper type setting of [Paper Tray
Attributes].
20
1 Basic Operations
2
Printing
2.1
Printing From the Computer
This section explains the basic flow when printing from application software in Windows®
environment.
(The procedure may differ according to the computer or system configuration used.)
Important
• Do not switch off the power of this printer when printing is in progress. It may lead to a paper jam.
1.
From the [File] menu of the application software, select [Print].
2.
Select this printer as the printer to be used to start printing.
To use the various print features of this printer, display the printer properties dialog box
to configure the settings of the necessary items.
For details on each item and how to configure its settings, refer to the Online Help for
the printer driver.
Important
• If the paper tray information is not correct, change the setting on the [Options] tab of the printer driver
before printing. For details about how to configure settings, refer to the Online Help for the printer driver.
A
There are two ways to display Online
Help for the printer driver.
A.
Click [?]. And then, click the item
you want to know more about. The
explanation on the item will be
displayed.
B.
Click [Help].
The [Help] window will be displayed.
Paper tray
information
B
Useful Print Features in the Properties Dialog Box
• [Basic] tab: 2 Sided Print, Multiple Up, Poster, Booklet Creation, Sample/Secure/Delayed
Print
• [Tray/Output] tab: Transparency Separators, Job Offset, Covers
• [Watermarks] tab: Watermarks
Note
• You can configure the print features in the properties dialog box from the printer icon in the window
displayed by selecting [Printers and Faxes] (or [Settings] > [Printers] depending on the OS).
2.1 Printing From the Computer
21
2.2
Printing on Envelopes
The procedure to print on envelopes is as follows. For details on the envelopes that can be
used, refer to “Usable Paper” (P. 55).
Loading Envelopes
You have to close the flaps of the envelope and load it with the address side facing up in
the orientation shown in the diagram below.
Paper feed direction
* The flap faces down.
The following explains how to load the envelopes, using Commerical #10 as an example,
in trays 1 to 4 and the bypass tray (optional).
Important
• The reverse side of the envelope cannot be printed on.
Loading Envelopes in Paper Tray
Note
• For details on the procedure to load paper in paper tray, refer to “Loading Paper in a Paper Tray” (P. 59).
22
2 Printing
1.
When loading Commercial #10, pull the
paper tray until A4 size. Load the
envelopes in the portrait orientation so that
the flaps are turned to the right side.
2.
Slide the length guide and right width guide to the size of the loaded envelopes.
3.
Close the lid of the paper tray and push the tray completely into the printer.
4.
On the control panel, change the paper type of the tray to [Heavyweight 1]. For
details, refer to “3.4 Setting Paper Types” (P. 64).
5.
On the control panel, change the paper size of the tray to [Custom] and then specify
the paper size (for Commercial #10: width: 104.8 mm, length: 241.3 mm). For details,
refer to “3.3 Setting Custom Paper Sizes” (P. 63).
6.
On the printer driver, register the size specified in step 5 as a custom paper size. For
details, refer to “Setting Custom Paper Sizes” (P. 29).
Loading Envelopes in Bypass Tray
Note
• For details on the procedure to load paper into the bypass tray, refer to “Loading Paper in the Bypass
Tray (Optional)” (P. 61).
1.
In the case of Commercial #10, pull out the
extension tray. Load envelopes in portrait
orientation so their flaps facing to the right.
2.
Slide the paper guides to the size of the
envelope.
3.
Set the paper size indicator to <Custom>.
4.
On the printer driver, register the envelope size as a custom paper size. For details,
refer to “Setting Custom Paper Sizes” (P. 29).
Printing on Envelopes
To print on envelopes, display the [Tray/Output] tab and [Basic] tab. This section explains
the procedure using WordPad on Windows XP as an example.
Note
• The way to display the printer properties dialog box differs according to the application software. Refer to
the manual of each application software.
1.
From the [File] menu, select [Print].
2.
Select this printer as the printer to be used and click [Preferences].
3.
Click the [Tray/Output] tab.
4.
If the envelope is loaded in the bypass tray, select [Tray 1 (Bypass)] from [Paper
Source].
If the envelope is loaded in trays 1 to 4, select the loaded paper tray from [Paper
Source] or click [Specify Paper Type] to display the [Specify Paper Type] dialog box
and then select [Heavyweight1] from [Paper Type].
4
5
2.2 Printing on Envelopes
23
5.
If you have selected [Tray 1 (Bypass)] from [Paper Source], click [Bypass Settings] to
display the [Bypass Settings] dialog box and then select [Heavyweight1] from [Paper
Type (Bypass Tray)].
Note
• If you have configured tray 1 as bypass tray on the [Options] tab of the printer properties dialog box,
[Tray 1 (Bypass)] and [Bypass Settings] can be selected.
6.
Click the [Basic] tab.
7.
From [Paper Size], select the size of the original document.
7
8
8.
From [Output Size], select the registered custom size.
9.
If necessary, select [Turn Image by 180deg] and then click [OK].
10. Click [Print] in the [Print] dialog box to start printing.
24
2 Printing
2.3
Printing on Transparencies
Loading Transparencies
Load transparencies in trays 1 to 4 or the bypass tray (optional).
Important
• Transparencies with white frame and full-color transparencies cannot be used.
Loading Transparencies in a Paper Tray
The way to load transparencies in the paper tray the same as the way to load standard size
paper. For details, refer to “3.2 Loading Paper” (P. 59).
You must also paper type for the paper tray in [Transparency] on the control panel.
Refer to “3.4 Setting Paper Types” (P. 64) to change the setting.
Load the Transparencies Into Bypass Tray
1.
After carefully fanning a small stack of
transparencies load them into the tray with
the side to be printed facing up. Load
transparencies a few at a time.
Side to be
printed
2.
Slide the paper guides to the size of the transparencies.
3.
Set the paper size indicator to the size of the transparencies.
Printing on Transparencies
To print on transparencies, display the [Tray/Output] tab and [Basic] tab. This section
explains the procedure using WordPad on Windows XP as an example.
Note
• The way to display the printer properties dialog box differs according to the application software. Refer to
the manual of your respective application software.
• Printing transparencies continuously may lead to the output transparencies sticking to each other. As a
guide, remove the transparencies from the output tray after about 20 sheets and then fan them to lower
their temperatures.
1.
From the [File] menu, select [Print].
2.
Select this printer as the printer to be used and click [Preferences].
3.
Click the [Tray/Output] tab.
2.3 Printing on Transparencies
25
4.
If the transparency is loaded in the bypass tray, select [Tray 1 (Bypass)] from [Paper
Source].
If the transparency is loaded in trays 1 to 4, select the loaded paper tray from [Paper
Source] or click [Specify Paper Type] to display the [Specify Paper Type] dialog box
and then select [Transparency].
4
5
5.
If you have selected [Tray 1 (Bypass)] from [Paper Source], click [Bypass Settings] to
display the [Bypass Settings] dialog box and then select [Transparency] from [Paper
Type (Bypass Tray)].
Note
• If you have configured tray 1 as bypass tray on the [Options] tab of the printer properties dialog box,
[Tray 1 (Bypass)] and [Bypass Settings] can be selected.
6.
Click the [Basic] tab.
7.
From [Paper Size], select the size of the original document.
7
8
26
2 Printing
8.
From [Output Size], select the size of the transparency, and then click [OK].
9.
Click [Print] in the [Print] dialog box to start printing.
2.4
Printing on Custom Size Paper/Long Paper
This section explains how to print on custom size paper such as long paper.
The paper sizes that can be selected on this printer are as follows:
„ For tray 1
„ For trays 2 - 4
Long edge:
98 to 900 mm
Short edge:
76 to 305 mm
„ For bypass tray
Long edge:
148 to 432 mm
Short edge:
76 to 297 mm
Long edge:
98 to 900 mm
Short edge:
76 to 305 mm
* To load long-size paper with the long
edge exceeding 432 mm, load the
paper with the edge protruding from
the tray.
Loading Custom Size Paper
Loading Custom Size Paper in a Paper Tray
The way to load custom size paper with the long edge shorter than 432 mm in trays 1 to 4
is the same as loading standard size paper. For details, refer to “3.2 Loading Paper” (P. 59).
To load long paper in tray 1, follow the procedure below:
1.
Pull the paper tray to its maximum.
Note
• Pull the extendable part out to its maximum (A3 size).
For details on the procedure to extend the paper tray,
refer to “3.2 Loading Paper” (P. 59).
2.
Load the paper with the side to be printed
facing up. Curl up the back end of the paper
so that it will not fall from the tray.
3.
Push the paper tray completely into the printer.
Important
• Do not close the lid of the paper tray.
2.4 Printing on Custom Size Paper/Long Paper
27
Loading Custom Size Paper in Bypass Tray
This section explains the procedure to load custom size paper, using long paper as an
example, in the bypass tray.
Note
• For details on loading other custom size paper except long paper, refer to “Loading Paper in the Bypass
Tray (Optional)” (P. 61).
1.
Load the long paper with the side to be
printed facing up and with the back edges
curled up as shown in the diagram (1).
Important
• Curl up the back edges of the long paper in as far a
position as possible from the paper entry point. Doing
it too near to the paper entry point may cause the back
edges of the curled paper to be caught in the entry
point and the paper to be torn.
• Load the paper one sheet at a time.
2.
Slide the paper guides to the size of the long paper (2).
3.
Set the paper size indicator to <Custom>.
4.
Pull out the extension output tray.
Note
• Output the paper one sheet at a time to prevent paper
jam.
28
2 Printing
Side to be printed
Setting Custom Paper Sizes
Before printing, set the custom size on the printer driver.
You have to configure the settings on the control panel too when loading custom size paper
in trays 1 to 4. For details on setting the control panel, refer to “3.3 Setting Custom Paper
Sizes” (P. 63).
Important
• When setting the paper size on the printer driver and control panel, be sure to specify the same size as
the actual paper used. Setting the wrong size for printing will cause the machine failure. This is
especially true if you configure a bigger size when using a narrow width paper.
On the printer driver, set the custom size in the [Custom Paper Size] dialog box. This section
explains the procedure using Windows XP as an example.
Note
• For Windows NT 4.0/Windows 2000/Windows XP/Windows Server 2003, only users with administrator’s
rights can change the settings. Users without the rights can only check the contents.
• When configuring the [Custom Paper Size] dialog box in Windows NT 4.0/Windows 2000/Windows XP/
Windows Server 2003, settings of other printers on the computer will also be affected as the form data
base of the computer is used by a local printer. For a shared printer on the network, settings of other
shared printers on the same network in another computer will also be affected as the form data base on
the server with existing print queue is used. When setting on Windows 95/Windows 98/Windows Me,
settings of other printers on the computer will not be affected as the settings are for paper sizes defined
by each printer icon. For shared printers on the network, settings of other shared printers on the same
network but in another computer will not be affected as the settings are for paper sizes defined by each
printer icon.
1.
From the [Start] menu, click [Printers and Faxes] and then display the properties of the
printer to be used.
2.
Click the icon of this printer, and then select [Properties] from the [File] menu.
3.
Click the [Configuration] tab.
4.
Click [Custom Paper Size].
4
2.4 Printing on Custom Size Paper/Long Paper
29
5.
Use the [Details] list box to select the custom setup you want to define.
5
6
7
6.
Specify the length of the short edge and long edge under [Change Setting For].
You can specify the values either by entering directly or using [ ] [ ].
The length of the short edge cannot be longer than the long edge, even if it is within the
specified range. The length of the long edge cannot be shorter than the short edge,
even if it is within the specified range.
7.
To assign a paper name, select the [Name the Paper Size] check box and then enter
the name in [Paper Name]. Up to 14 characters can be used for the paper name.
8.
If necessary, repeat steps 5 to 7 to define another custom size.
9.
Click [OK].
10. When you have configured custom sizes for trays 1 to 4 using the control panel, click
[Get Information from Printer] on the [Options] tab.
The printer settings can be displayed on the printer driver.
Refer to
• “1.5 Displaying Optional Accessory Configuration and Paper Tray Settings” (P. 20)
11. Click [OK].
Printing on Custom Size Paper
The procedure to print on custom size paper is as follows.
This section explains the procedure using WordPad on Windows XP as an example.
Note
• The way to display the printer properties dialog box differs according to the application software. Refer to
the manual of your respective application software.
30
2 Printing
1.
From the [File] menu, select [Print].
2.
Select this printer as the printer to be used and click [Preferences].
3.
Click the [Tray/Output] tab.
4.
Select the appropriate tray from [Paper Source].
4
5
5.
If you have selected [Tray 1 (Bypass)] from [Paper Source], click [Bypass Settings] to
display the [Bypass Settings] dialog box and then select the paper type from [Paper
Type (Bypass Tray)].
Note
• If you have configured tray 1 as bypass tray on the [Options] tab of the printer properties dialog box,
[Tray 1 (Bypass)] and [Bypass Settings] can be selected.
6.
Click the [Basic] tab.
7.
From [Paper Size], select the size of the original document.
7
8
8.
From [Output Size], select the registered custom size, and then click [OK].
9.
Click [Print] in the [Print] dialog box to start printing.
2.4 Printing on Custom Size Paper/Long Paper
31
2.5
Print Confidential Document - Secure
Print
When the hard disk (optional) has been installed, you can use the secure print feature.
Important
• The hard disk may be damaged and erase important data saved in the hard disk. We recommend you
back up your data.
About Secure Print
Secure Print is a feature that allows you to attach a password to a piece of print data on the
computer, send it to the printer for temporarily storing, and start printing the data from the
control panel. You can also store the print data in the printer without attaching a password.
By storing frequent-used data in the printer, you can print the data out by just operating on
this printer, and without sending them from the computer again and again.
Send
data
Store in
printer
Use control panel
to output data
Note
• You can select whether to delete secure print data after printing. For details, refer to “At the Control
Panel” (P. 34).
• To delete all secure print data that has become redundant, refer to “Init/Del Data” (P. 94).
• If [Disable] is selected for the setting of [Secure Print] control panel setting, secure print data cannot be
output.
Configuring Secure Print
The procedure to configure Secure Print is as follows.
First of all, carry out the secure print settings at the computer and send data to the printer
for printing. Then, carry out the output procedure at the printer to output the print data.
At the Computer
This section explains the procedure using WordPad on Windows XP as an example. The
procedure is the same for other OS.
Note
• The way to display the printer properties dialog box differs according to the application software. Refer to
the manual of your respective application software.
32
2 Printing
1.
From the [File] menu, select [Print].
2.
Select this printer as the printer to be used and click [Preferences].
3.
From [Job Type] on the [Basic] tab, select [Secure Print].
3
4.
Enter the user ID in [User ID].
You can enter up to eight characters for the user ID.
4
5
6
5.
To enter a password, enter it in [Password].
Enter up to 12 numeric characters.
6.
From [Retrieve Document Name], select either [Enter Document Name] or [Auto
Retrieve].
If [Enter Document Name] is selected, specify a document name in [Document Name]
using up to 12 characters.
If [Auto Retrieve] is selected, the name of the document to be printed will become the
document name. However, if the printer cannot recognize a document name, it will
become the date/time (e.g. 09/03 10:30).
7.
Click [OK].
8.
Click [OK] on the [Basic] tab.
9.
Click [Print] in the [Print] dialog box to start printing.
The document will be stored in the printer.
2.5 Print Confidential Document - Secure Print
33
At the Control Panel
This section explains the procedure to print data stored in the printer by Secure Print.
Note
• You can also delete, without printing, secure print data stored in the printer. For details, refer to “Init/Del
Data” (P. 94).
1.
Press the <
> button.
2.
Check that [Secure Print] is displayed and then press the < > button.
3.
Press the < > or < > button until the required user is selected and then press the
< > button.
4.
Move the cursor by the < > button and then enter the password (within 12 digits) by
the < > and < > buttons.
5.
Press the <Eject/Set> button.
6.
Press the < > or < > button until the required document is selected and then press
the < > button.
7.
After printing, press the < > or < > button to delete or save the document and then
press the < > button.
8.
Press the <Eject/Set> button. Printing will start.
9.
Press the <Menu> button when printing has completed.
Note
• The displayed user ID (up to eight characters) is the [User ID] specified in the [Secure Print] dialog box
of the [Basic] tab of the printer driver.
• For the password, enter the [Password] set in the [Secure Print] dialog box of the [Basic] tab of the
printer driver. If [Password] is not configured, there will be no setting on the control panel.
• The document name displayed (up to 12 characters) is the [Document Name] specified in the [Secure
Print] dialog box of the [Basic] tab of the printer driver.
34
2 Printing
2.6
Print After Checking Printing Result Sample Print
When the hard disk (optional) has been installed, you can use the sample print feature.
Important
• The hard disk may be damaged and erase important data saved in the hard disk. We recommend you
back up your data.
About Sample Print
Sample Print is a feature that allows you to store the print data of multiple copies in the hard
disk (optional), print out only the first set to check the print result and if satisfactory, print the
remaining copies from the control panel.
Note
• Sample print data that has become redundant can be deleted using the control panel. For details, refer
to “At the Control Panel” (P. 34).
If result is
OK
Print only one document
Send
data
Print out remaining sets
using the control panel
Store in
printer
If result is
not OK
Stop printing using the
control panel
Configuring Sample Print
The procedure to configure Sample Print is as follows.
First of all, carry out the sample print settings at the computer and send data to the printer
for printing. Then, carry out the output procedure at the printer to output the print data.
At the Computer
This section explains the procedure using WordPad on Windows XP as an example.
Note
• The way to display the printer properties dialog box differs according to the application software. Refer to
the manual of your respective application software.
1.
From the [File] menu, select [Print].
2.
Select this printer as the printer to be used and click [Preferences].
3.
On the [Basic] tab, specify at least 2 for [Copies].
2.6 Print After Checking Printing Result - Sample Print
35
4.
Select [Sample Print] from [Job Type].
Note
• You must specify at least 2 for [Copies] before [Sample Print] can be selected.
4
5.
Enter the user ID in [User ID].
You can enter up to eight characters for the user ID.
5
6
6.
From [Retrieve Document Name], select either [Enter Document Name] or [Auto
Retrieve].
If [Enter Document Name] is selected, specify a document name in [Document Name]
using up to 12 characters.
If [Auto Retrieve] is selected, the name of the document to be printed will become the
document name. However, if the printer cannot recognize a document name, it will
become the date/time (e.g. 09/03 10:30).
36
2 Printing
7.
Click [OK].
8.
Click [OK] on the [Basic] tab.
9.
Click [Print] in the [Print] dialog box to start printing.
At the Control Panel
This section explains the procedure to print and delete data stored in the printer by Sample
Print.
1.
Press the <
> button.
2.
Press the < > or < > button until [Sample Print] is displayed and then press the
< > button.
3.
Press the < > or < > button until the required user is selected and then press the
< > button.
4.
Press the < > or < > button until the required document is selected and then press
the < > button.
5.
Press the < > or < > button to print or delete the saved document and then press
the < > button.
6.
Press the <Eject/Set> button.
The document will be deleted or printed.
7.
After the document is deleted or printed, press the <Menu> button.
Note
• The user ID displayed (up to eight characters) is the [User ID] set in the [Sample Print] dialog box of the
[Basic] tab of the printer driver.
• The document name displayed (up to 12 characters) is the [Document Name] set in the [Sample Print]
dialog box of the [Basic] tab of the printer driver.
2.6 Print After Checking Printing Result - Sample Print
37
2.7
Print at a Specified Time - Delayed Print
When the hard disk (optional) has been installed, you can use the delayed print feature. The
delayed print feature allows you to store the data in the printer beforehand and then print it
out automatically at the specified time.
Important
• The hard disk may be damaged and erase important data saved in the hard disk. We recommend you
back up your data.
• If the printer is switched off before the specified time, the specification of time will be undone and printing
will start once the power is switched on again. Do not switch off the power of the printer when using the
delayed print feature.
Note
• The time that can be specified for this feature is within 24 hours from the time you send the data for
printing.
Registering Delayed Print
The procedure to configure Delayed Print is as follows.
This section explains the procedure using WordPad on Windows XP as an example. The
procedure is the same for other OS.
1.
From the [File] menu, select [Print].
2.
Select this printer as the printer to be used and click [Preferences].
3.
From [Job Type] on the [Basic] tab, select [Delayed Print].
3
38
2 Printing
4.
Set the time to start printing by [Hour] and [Minutes].
Use the 24-hour system.
4
5
5.
From [Retrieve Document Name], select either [Enter Document Name] or [Auto
Retrieve].
If [Enter Document Name] is selected, specify a document name in [Document Name]
using up to 12 characters.
If [Auto Retrieve] is selected, the name of the document to be printed will become the
document name. However, if the printer cannot recognize a document name, it will
become the date/time (e.g. 09/03 10:30).
6.
Click [OK].
7.
Click [OK] on the [Basic] tab.
8.
Click [Print] in the [Print] dialog box to start printing.
Printing will start at the specified time.
Canceling Delayed Print
Use the control panel to cancel Delayed Print or to print without waiting for the specified
time.
1.
Press the <
> button.
2.
Press the < > or < > button until [Delayed Print] is displayed and then press the
< > button.
3.
Press the < > or < > button until the required document is selected and then press
the < > button.
4.
Press the < > or < > button to delete or immediately print the saved document and
then press the < > button.
5.
Press the <Eject/Set> button. The document will be deleted or printed.
6.
After the document is deleted or printed, press the <Menu> button.
Note
• The document name displayed (up to 12 characters) is the [Document Name] set in the [Delayed Print]
dialog box of the [Basic] tab of the printer driver.
2.7 Print at a Specified Time - Delayed Print
39
2.8
Direct Printing of PDF File
You can send PDF files directly to the printer for printing without using the printer driver. As
the print data is sent directly to the printer, the printing process will be simpler than printing
with the printer driver and at a faster speed. The way to print a PDF file directly is as follows.
„ Using PDF Bridge Feature
To print PDF file using the PDF Bridge feature, you can use ContentsBridge Utility (Utility
software is supplied by Fuji Xerox) or lpr command to send the data directly to the printer.
PostScript software kit (optional) is required to use the PDF Bridge feature.
Note
• When using ContentsBridge Utility, refer to “Using ContentsBridge Utility to Print PDF” (P. 41). When
using lpr command, refer to “Printing a PDF File Without Using ContentsBridge Utility” (P. 47).
• To use the PDF Bridge feature correctly for printing, you may need to have the additional memory
(optional).
„ Using PostScript Feature
When the PostScript software kit (optional) has been installed, you can use the PostScript
feature to send PDF file to the printer directly for printing.
Note
• When using the PostScript feature to print PDF files directly, refer to “PDF” (P. 71) for details on how to
set [Process Mode] of [PDF] to [PS] on the control panel and then refer to“Printing a PDF File Without
Using ContentsBridge Utility” (P. 47) for details on how to print.
• Using the PostScript feature can print PDF file attached with object using LZW compression. LZW uses
the LZW algorithm that has received the license of US Patent No. 4,558,302.
Important
• When using USB or parallel port to print PDF file directly, use ContentsBridge Utility.
PDF Files That Can Be Printed
PDF files that can be printed are those created by Adobe Acrobat 4 and Adobe Acrobat 5
(except one part of the features added by PDF 1.4).
Note
• You may not be able to print some PDF files directly by the printer due to the way of creating them.
When this happens, open the PDF files and use the printer driver to print them.
40
2 Printing
Using ContentsBridge Utility to Print PDF
Operating Environment for ContentsBridge Utility
ContentsBridge Utility supports the IBM PC-AT and the compatibles on which the OSs
described bellow can operate, and also supports PowerPC-based Macintosh computers.
„ Windows Environment
Connection
Windows 95
Windows 98/Me
Windows NT 4.0
Windows 2000/XP
Windows Server
2003
Parallel
USB
Network*
* Connected via the port that has been specified on the selected printer. For example, if the lpr port has
been specified, the lpr port is used for printing.
„ Macintosh Environment
Connection
Mac OS X v10.2.x
USB
Network
(EtherTalk or lpr port)
Note
• The PostScript software kit (optional) is required to use the EtherTalk port.
Installing ContentsBridge Utility
Copy the [ContentsBridge.exe] file (Windows) from the Software Pack CD-ROM to a folder
or the desktop of the computer.
Note
• [ContentsBridge.exe] file (Windows) is stored in the [Cbridge] folder in the CD-ROM bundled with this
printer.
• [ContentsBridge] file (Macintosh) can be downloaded from the web site address (URL) listed below.
URL: http://www.fxap.com.sg/suppdrv.jsp
2.8 Direct Printing of PDF File
41
Items That Can Be Configured Using ContentsBridge Utility
Print Range
Specifies the pages to be printed.
Quantity
„ Quantity
Specifies the copies to be printed between 1 to 999.
„ Collated
Specifies whether to collate multiple copies of the printout by sets (sorted in the order of
page 1, 2, 3,...1, 2, 3...).
Printer Setting
„ Output Color
This item is not enabled in this printer.
„ Print Mode
[High Speed]
Select this when you want a faster printing speed.
[High Quality]
Select this when you want a clearer printout.
[Standard]
Select this when you want both standard speed and quality.
„ Paper Size
[A4]
Select this to print in A4 size paper.
[Auto]
Select this to print in a paper size that is automatically determined
according to the size and settings of the PDF file to be printed.
„ Paper Type
[Plain]
Select this to use plain paper for printing.
[Printer Settings]
Select this to use the paper loaded in the paper tray or bypass tray
for printing. The paper type will be the option specified on the
common menu of the control panel.
„ 2 Sided Print
[1 Sided Print]
Select this to print on one side of the paper.
[Long Edge Flip]
Select this to print on both sides of the paper with the images of both
sides facing the same direction if the paper is flipped along the long
edge.
[Short Edge Flip]
Select this to print on both sides of the paper with the images of both
sides facing the same direction if the paper is flipped along the short
edge.
„ Layout
[Auto Zoom]
Select this to enlarge/reduce the image size automatically according
to the paper size.
[100%]
Select this to print in the actual size of the image.
[Booklet]
Select this to print the pages on both sides of the paper and arranged
like a booklet.
Note
• Some PDF files cannot be printed in the form of a booklet due to page
structure. In this case, you can still obtain the booklet result by selecting
[Long Edge Flip] for [2 Sided Print] and [Auto Zoom] for [Layout].
42
2 Printing
[2 up]
Select this to arrange and print two pages on a single sheet of paper.
The paper size is fixed at A4.
[4 up]
Select this to arrange and print four pages on a single sheet of paper.
The paper size is fixed at A4.
Printing PDF File (for Windows)
1.
Double-click the [ContentsBridge.exe] icon to activate it.
The [ContentsBridge] dialog box appears.
2.
Select this printer as the printer to be used.
3
2
3.
For [File to Print], either enter the path of the PDF file to be printed or click [Browse] to
specify the target file.
4.
Click [Print].
5.
Configure the settings of the various items.
6.
In the [PDF File Print] dialog box, click [OK]. The print data will be sent to the printer.
At this point, a dialog box appears if a password has been assigned to the PDF file.
Enter the password for the PDF file and click [OK].
7.
In the [ContentsBridge] dialog box, click [Exit].
2.8 Direct Printing of PDF File
43
„ Printing PDF Files With a Simple Procedure
You can print PDF files with a simple procedure if this printer is configured as the default
printer and a shortcut icon of [ContentsBridge.exe] is created on the desktop.
1.
Drag and drop the PDF file to be printed over the shortcut icon of
[ContentsBridge.exe].
The [Print Settings Confirmation] dialog box appears.
2.
To set print settings using the [PDF File Print] dialog box, click [Print Settings] (1).
If there is no need to set print settings, click [OK] in the [Print Settings Confirmation]
dialog box (2).
The print data will be sent to the printer.
Selecting this check box will enable print
data to be sent to the printer when you just
drag and drop the PDF file after the printer
has been activated again.
Note
• If the check box is not selected,
double-click the shortcut icon to activate
it. When you drag and drop the file the
next time, the [Print Settings
Confirmation] dialog box appears again.
(2)
(1)
Clicking [OK] will send the
print data to the printer.
44
2 Printing
Printing PDF File (for Macintosh)
This section explains the procedure using Mac OS X v10.2.6 as an example.
1.
Drag and drop the PDF file to be printed over the [ContentsBridge] icon.
The [Print PDF] dialog box appears.
2.
Click [Select Printer].
2
3.
Select this printer in the displayed dialog box, click [Apply].
3
Note
• To use the AppleTalk for printing, set [Printer Type] to [PostScript Printer].
2.8 Direct Printing of PDF File
45
4.
Set the various items.
5.
In the [PDF File Print] dialog box, click [OK]. The print data will be sent to the printer.
At this point in time, a dialog box appears if a password has been set for the PDF file.
Enter the password set for the PDF file and click [OK].
6.
46
2 Printing
Select [Quit ContentsBridge] from the [ContentsBridge] menu.
Printing a PDF File Without Using ContentsBridge Utility
Here, we send the PDF file to the printer for printing using lpr command directly and not
ContentsBridge Utility. Printing will be done with the following items configured according to
the control panel settings.
• Process Mode
• Password
• Quantity
• Collate
• 2 Sided
• Output Size
• Print Mode
• Layout
Refer to
• “PDF” (P. 71)
Note
• [Layout] will not be displayed when [PS] has been selected for [Process Mode].
• When lpr command is used for printing, specify the number of copies by lpr command. The [Quantity]
setting on the control panel will become disabled. Also, if the number of copies is not specified by lpr
command, it will be treated as one copy.
When using lpr command to print PDF file, you have to use the control panel or CentreWare
Internet Services to activate the LPD port on the printer.
Refer to
• “Network/Port” (P. 76)
Target OSs
Windows NT 4.0/Windows 2000/Windows XP/Windows Server 2003
Printing PDF File
The following specification on the computer is an example of using lpr command to print
PDF file.
Note
•
indicates space.
Example: Printing a [event.pdf] file with a printer IP address of 192.168.1.100.
C:\>lpr
-S 192.168.1.100 -P lp event.pdf
<Enter> key
2.8 Direct Printing of PDF File
47
2.9
Printing From Web Browser
You can print from the web browser using CentreWare Internet Services.
This feature can be used when the hard disk (optional) has been installed.
Important
• The hard disk may be damaged and erase important data saved in the hard disk. We recommend you
back up your data.
Data That Can Be Sent
The files that can be sent from the web browser and printed on this printer are as follows:
• TIFF file
• PDF file created by Adobe Acrobat 4 and Adobe Acrobat 5 (except one part of the
features added by PDF1.4)
• PostScript file
• PCL file
• Text file
Note
• The PDF files sent will be printed by using the PDF Bridge or PostScript feature and according to the
[PDF] setting on the control panel. For details on the print features of the PDF file in this machine, refer
to “2.8 Direct Printing of PDF File” (P. 40).
• For details on the format of the TIFF file supported by this printer, refer to “TIFF File Format” (P. 156).
• The PostScript software kit (optional) is required to print PostScript file.
Printing
1.
Activate the computer and web browser.
2.
At the address column of the web browser, enter the IP address or URL of the printer
and then press the <Enter> key.
• Example of a URL entry
• Example of an IP address entry
The CentreWare Internet Services screen appears.
Note
• Depending on the web browser setting, the CentreWare Internet Services screen may not appear even if
the IP address has been entered. When this happens, refer to “Settings for CentreWare Internet
Services” (P. 130) for details on checking the web browser settings.
48
2 Printing
3.
Click [Services] and on the displayed screen, configure settings, such as the file to be
printed.
Note
• For details on the items that can be configured, refer to the Online Help for CentreWare Internet
Services.
• Print features that are not configured here will operate according to the following settings made on the
printer receiving the data:
• TIFF file: The logical printer value specified for [Emulation Setting] > [TIFF] > [Memory Settings] of
CentreWare Internet Services.
• PDF file: Value specified for [PDF] on the control panel.
4.
Click [Start].
Printing will start.
2.9 Printing From Web Browser
49
2.10
Printing via E-mail - E-mail Printing
When the hard disk (optional) has been installed and the printer is connected to a network,
enabling it to receive e-mails via TCP/IP communication, e-mails can be sent from the
computer to this printer.
Printing of e-mail contents and TIFF or PDF attachments can be done from this printer.
This feature is known as E-mail Printing.
Important
• The hard disk may be damaged and erase important data saved in the hard disk. We recommend you
back up your data.
Prints
automatically
E-mail
Prints
automatically
Environment Settings for E-mail Printing
To use the E-mail Printing feature, you need to configure server settings (such as SMTP
and POP3 servers) on your network environment.
Note
• Wrong e-mail environment settings may cause disruptions in your network. Always ask your network
administrator to configure e-mail environment settings.
Configuring the Network Environment
• Register user account
50
2 Printing
Configuring the E-mail Environment (at This Printer)
Configure the following items according to your e-mail environment under [Properties] of the
CentreWare Internet Services.
Note
• After configuring the settings, always click [Apply New Settings] and switch off/on the printer to reboot.
• Select the [Enable] check box of [Port Status] > [Receive E-mail] and switch off/on the printer, [E-mail]
will be displayed.
*: Default
Item
Item to be
configured
Description
Value
SMTP
POP3
{
{
{
{
Administrator
E-mail
Address
Set the internet service
administrator’s e-mail address.
Machine
E-mail
Address
Set the printer’s e-mail address.
The address specified here will
be displayed in the [From]
column of the e-mail.
Port Status
Receive
E-mail
Select the check box.
Protocol
Settings >
TCP/IP
Host Name
Set the host name of this
printer.
Up to 32 characters
{
{
Get DNS
Address
Select the check box to get the
DNS server address
automatically from the DHCP
server.
• Off: Manual*
• On: DHCP
{
-
DNS Address
1 to 3
Set the DNS server address
xxx.xxx.xxx.xxx
{
-
DNS Name
Set the DNS name.
Up to 255 alphanumeric
characters can be entered,
including the ASCII
characters for “.” (full stop)
and “-” (hyphen).
{
-
Machine
Details
Up to 128 alphanumeric
characters can be entered
including the ASCII
characters for “@” (at
mark), “.” (full stop), “-”
(hyphen) and “_”
(underscore).
Required settings
for the Receiving
Protocol
-
2.10 Printing via E-mail - E-mail Printing
51
*: Default
Item
Protocol
Settings >
E-mail
52
2 Printing
Item to be
configured
Description
Value
Required settings
for the Receiving
Protocol
SMTP
POP3
Receiving
Protocol
Set the e-mail receiving
method.
• SMTP*
• POP3
{
{
Print Mail
Headers and
Contents
Set to print the attachments
(TIFF, PDF) of the received mail
together with the mail header.
To print all mail header
information such as the
receiving route, select [All
Headers and Contents].
• None
• Auto Mail Contents
• Basic Headers and
Contents*
• All Headers and Contents
{
{
POP3 Server
Address
Set the IP address of the POP3
server for receiving e-mails or
the FQDN (Fully Qualified
Domain Name).
Up to 128 alphanumeric
characters can be entered,
including the ASCII
characters for “.” (full stop)
and “-” (hyphen).
-
{
POP3 Server
Check
Interval
Set the interval for checking
e-mails in the POP3 server.
1 to 120 minutes
10 minutes*
-
{
POP User
Name
Set the user name for
connecting to POP3 server.
Only 1 user can be specified.
Up to 64 alphanumeric
characters can be entered
including the ASCII
characters for “@” (at
mark), “.” (full stop), “-”
(hyphen) and “_”
(underscore).
-
{
POP User
Password
Set the password for POP User.
Enter the password again in
[Confirm Password].
Up to 64 alphanumeric
characters can be entered.
-
{
SMTP
Sending
Authentication
Select the [POP before SMTP]
check box to confirm the user at
the POP server before sending
e-mails to the SMTP server.
{
-
SMTP Server
Address
Set the IP address of the SMTP
server for receiving e-mails or
the FQDN (Fully Qualified
Domain Name).
{
-
-
Up to 128 alphanumeric
characters can be entered,
including the ASCII
characters for “.” (full stop)
and “-” (hyphen).
Sending E-mails
Attachments That Can Be Sent
The following files can be sent as an attachment.
• PDF file created by Adobe Acrobat 4 and Adobe Acrobat 5 (except one part of the
features added by PDF1.4)
• TIFF file
Note
• The PDF files sent will be printed by using the PDF Bridge or PostScript feature and according to the
[PDF] setting on the control panel. For details on the print features of the PDF file in this printer, refer to
“2.8 Direct Printing of PDF File” (P. 40).
• For details on the format of the TIFF file supported by this printer, refer to “TIFF File Format” (P. 156).
Sending E-mails
This section explains how to send e-mails from the computer to each printer using Outlook
Express as an example.
1.
Create mail contents using your mailing software and attach TIFF or PDF files if any.
Important
• Only text format can be used for the mail contents. Specify text as the format of e-mail content in your
mail software.
Note
• If the extension of the attached file is not “tif” or “pdf”, it may not be printed correctly.
• Maximum 31 documents can be attached.
2.
Enter the printer’s e-mail address in the address column.
3.
Send the e-mail. The printer will print the e-mail automatically after receiving it.
Note
• The mail contents and the attached documents will be printed according to the following settings at the
printer receiving the data. Note that specifying the offset output feature is invalid in any case.
• TIFF file attachment: The logical printer value selected for [Emulation Settings] > [TIFF] > [Memory
Settings] of CentreWare Internet Services.
• PDF file attachment: Value specified for [PDF] on the control panel.
Receiving and Printing E-mails
This printer allows you to receive and print e-mails manually using the control panel.
1.
Press the <
> button.
2.
Press the < > or < > button until [Mail Print] is displayed.
3.
Press the < > button.
4.
Press the <Eject/Set> button.
The printer starts to receive e-mails. E-mails will be printed once received.
2.10 Printing via E-mail - E-mail Printing
53
Points to Note When Sending E-mails
Security Issues
E-mails are sent via internet, connecting computers from all over the world. As a result,
caution must be made relating to security issues such that information is not easily seen or
altered by third parties.
Therefore, you are recommended to use methods to ensure that important information is
secured. You are also advised not to reveal the e-mail address of this printer to third parties
to avoid receiving junk mails.
Setting Permitted Domain
You can configure this printer such that it only receives e-mails from specific domains.
For details on how to specify the permitted domain, refer to the Online Help for CentreWare
Internet Services.
Caution on Connecting This Printer to Internet Provider and Using
E-mail Features
• In the case where a flat-rate contract with the internet provider exists and the user is not
always connected to the network, a telephone charge will incur every time this printer
retrieves data regularly from the mail server.
• Connect the printer to an IP masqueraded environment. Functionality of this printer is not
guaranteed when it is assigned global IP addresses.
• When receiving e-mails via POP, always apply an exclusive e-mail account for the printer.
Using a common e-mail account shared with other users will result in errors.
• When the internet connection speed is slow, it takes time to receive huge data such as
image data.
• There are also providers that allows receiving of e-mails via SMTP. Detailed adjustments
with the provider is required for such cases.
• When setting up e-mail configuration in an environment where MTA support is set up in
private segments, match the operating configuration.
54
2 Printing
3
About Paper
3.1
About Paper
Using unsuitable paper may lead to paper jams, poor print quality, breakdown and damage
to your printer. In order to use the features of this printer effectively, we suggest using only
paper that is recommended here.
When you use paper that is not recommended, contact our Customer Support Center or
your dealers.
Usable Paper
The types of paper that can be used on this printer are as follows.
When printing on paper that is commonly sold, use the types of paper in the following table.
However, it is recommended to use paper in the next category, standard paper for clearer
printing.
Paper tray
Tray 1
Size
Standard sizes that can be automatically detected:
A5
, B5
, A4
, A4
, B4
, A3
Weight
Loading Capacity
60 - 216 g/m2
150 sheets (P paper)
or 17.5 mm or below
60 - 216 g/m2
250-sheet tray:
250 sheets (P paper)
or 27.6 mm or below
,
Letter (8.5 × 11")
, Legal (8.5 × 14")
Others:
Custom (76 × 98 to 305 × 900 mm)
Tray 2 to 4
(tray 3 and 4 are
optional)
Bypass tray
(optional)
Standard sizes that can be automatically detected:
A5
, B5
, A4
, A4
, B4
, A3
,
Letter (8.5 × 11")
, Legal (8.5 × 14")
Others:
Custom (76 × 148 to 297 × 432 mm)
550-sheet tray:
550 sheets (P paper)
or 59.4 mm or below
Standard sizes that can be automatically detected:
B5
, A4
, B4
Legal (8.5 × 14")
, A3
, Letter (8.5 × 11")
, Executive (7.25 × 10.5")
,
60 - 135 g/m2
Japanese official
100 sheets (P paper)
or 10 mm or below
postcard: 190 g/m2
Others:
A5
, Custom (76 × 98 to 305 × 900 mm)
*A5
, B5
, 7.25 × 10.5"
is not available.
Important
• Printing on paper whose setting is different from the paper size or paper type selected on the printer
driver or loading paper into an unsuitable paper tray for printing may lead to paper jams. To ensure
printing is correctly done, select the correct paper size, paper type, and paper tray.
• The printed image may fade due to moisture such as water, rain or vapor. For details, contact our
Customer Support Center or your dealers.
3.1 About Paper
55
Standard Paper
The following table shows the standard paper for this printer.
Paper
name
Weight
Paper type
64 g/m2
Plain
Medium weight paper for internal distribution and
general office use
XEROX
4024DP
20 lb
Plain
Medium weight paper for internal distribution and
general office use
XEROX
4200DP
20 lb
Plain
Medium weight paper for internal distribution and
general office use
80 g/m2
Plain
Medium weight paper for internal distribution and
general office use
FX P
RX80
Paper characteristics and caution on usage
Other Paper
The following table shows the types of paper recommended by our company.
Paper
name
56
Weight
Paper type
FX L
64 g/m2
Plain
Medium weight paper for internal distribution and
general office use
FX EP
64 g/m2
Plain
Quality printing paper
FX EPR
67 g/m2
Recycled
Recycled paper with 70% or more pulp that is ideal for
long-term storing
FX R
67 g/m2
Recycled
Recycled paper with 70% or more pulp that is ideal for
long-term storing
3 About Paper
Paper characteristics and caution on usage
Special Media
The following types of paper can be used for printing on this printer. These types of paper
are called special media.
Paper name
JE001
Weight
Paper type
-
Transparency
Paper characteristics and caution on
usage
Transparency without any white frame
Note
• As output transparencies may stick
together, remove the transparencies from
the output tray after about 20 sheets, and
then fan them to lower their temperature.
20 face label
V860
-
Heavyweight1
190 g/m2
Heavyweight2
-
Heavyweight1
RX110
110 g/m2
Heavyweight1
KF135
135 g/m2
Heavyweight1
Japanese official
postcard
Envelope
Important
• The reverse side of the envelope cannot be printed on.
• Quality of printing on both sides of postcards cannot be guaranteed.
• It may take a very long time (maximum 60 seconds) to print custom size Heavyweight 2 paper.
Note
• For details on special media, such as heavyweight not listed in the table, contact our Customer Support
Center or your dealers.
• Refer to “2 Printing” (P. 21) on how to print on transparencies or envelopes.
3.1 About Paper
57
Unusable Paper
Using the following types of paper might cause paper jams, malfunctions or damage to the
machine. Do not use them.
• Fuji Xerox full-color transparencies (example: V556, V558, V302)
• Paper exclusively for ink-jet printer use
• Paper that is too thick or thin
• Paper that has been printed on before (including color printing)
• Wrinkled, folded or torn paper
• Wet paper
• Curled paper
• Paper with static electricity
• Adhesive paper
• Postcards with pictures
• Paper with special coatings
• Treated colored paper
• Paper using ink that will run at a temperature of 150 °C
• Thermal paper
• Carbon paper
• Paper with staples, paper clips, ribbons or tape
• Paper with rough surfaces such as pulp paper, or fibrous paper
• If acid paper is used, the characters might appear fuzzy. Replace it with alkaline paper.
• Envelopes that are not flat or have metal fasteners
• Labels that do not fully cover the adhesive backing
Storing and Handling Paper
Even for suitable papers, poor storage conditions may lead to a change in the paper quality,
paper jams, poor print quality and machine breakdown. Take note of the following points
when storing paper:
• Store paper in the following locations: Temperature of 10 - 30 °C with a relative humidity
of 30 - 65%
• After opening a ream of paper, use the original cover sheets to wrap up the paper not
used and store it in a cabinet or a location with low humidity.
• Do not let the paper stand but store it in a flat location.
• Ensure that the paper is stored properly without being bent or curled.
• Store the paper in a location not exposed to direct sunlight.
58
3 About Paper
3.2
Loading Paper
Loading Paper in a Paper Tray
Refer to
• Paper type and size that can be loaded in paper tray: “Usable Paper” (P. 55)
1.
Place the paper tray on a flat surface and
remove the lid.
2.
If the base plate of the paper tray is raised,
push it down.
3.
When loading paper that is larger than
A4-size, slide the left and right lock tabs
outwards to unlock them. If you are loading
a paper size of A4 or smaller, proceed to
step 6.
4.
Hold the grip of the paper tray and pull its
extendable part to the front until it reaches
the paper size (B4 or A3).
3.2 Loading Paper
59
5.
Slide the tabs that you shifted at step 3
inwards to lock them.
6.
Squeeze the length guide and slide it to the
desired paper size (1). Squeeze the right
width guide and slide it to the desired paper
size (2).
7.
Load the paper with the side to be printed
facing up and with all four corners aligned.
Make sure the paper is not on top of the
side guide. Change the paper size label to
match the size of the loaded paper.
Important
• Do not load paper so it exceeds the maximum fill line
or the maximum capacity allowed.
• Align the right width guide with the paper width
correctly. If the right width guide is not in place, the
paper will not be properly fed and this may cause
paper jams.
Note
• For details about loading envelopes and long paper, refer to “2.2 Printing on Envelopes” (P. 22) and “2.4
Printing on Custom Size Paper/Long Paper” (P. 27).
8.
Close the lid of the paper tray and push the tray completely into the printer.
Important
• The lid of the tray must be firmly closed. If not, the paper might become misaligned.
• When the paper tray is extended, close the lid of the extendable part.
9.
Depending on the types and sizes of the loaded paper, you need to configure settings
on the control panel. Change the paper type when non-plain paper such as recycled
paper, heavyweight paper or transparencies are loaded. Configure the paper size
when custom size paper is loaded.
Refer to
• Paper type and size that can be loaded: “Usable Paper” (P. 55)
• Specifying the paper size: “3.3 Setting Custom Paper Sizes” (P. 63)
• Specifying the paper type: “3.4 Setting Paper Types” (P. 64)
60
3 About Paper
Loading Paper in the Bypass Tray (Optional)
Important
• Load paper into the bypass tray after switching on power.
Refer to
• Paper type and size that can be loaded in the bypass tray: “Usable Paper” (P. 55)
1.
Open the bypass tray (1). When loading
long paper, pull out the extension tray (2).
If the extension tray is still not long enough
for the paper you are loading, pull the
extension tray further (3).
2.
Match the paper guides to the scale for the
size of the paper you are loading (1). Place
the paper on the bypass tray with the
printing side face up and with all four
corners aligned, and insert the paper until it
lightly contacts the insertion inlet (2). Match
the paper size indicator on the bypass tray
with the size and orientation of the paper
you are loading (3)
Extension
output tray
Important
• When paper larger than A4 in size is loaded on the bypass tray, be sure to pull out the extension output
tray.
• If the paper guides are not in place, the paper will not be properly fed and this may cause paper jams.
• Do not load paper exceeding maximum capacity allowed.
• If there is no corresponding size or orientation for the paper you are loading on the size setting dial, set
the dial to <Custom>.
3.
When you are printing without using the printer driver (e.g. when using the
ContentsBridge Utility), the paper type setting on the control panel is enabled. When
the paper types has been changed, set the new paper type on the control panel.
Refer to
• “3.4 Setting Paper Types” (P. 64)
Note
• When you are printing with the printer driver, set the paper type on the [Tray/Output] tab.
3.2 Loading Paper
61
Automatic Tray Selection
If you display the properties dialog box of the printer driver and select a paper type for
[Specify Paper Type] and [Auto] for [Paper Source] on the [Tray/Output] tab for printing, this
printer will be able to automatically detect paper trays loaded with the selected paper type
and then among them, select the tray that matches the size and orientation of the document
to be printed. This feature is known as automatic tray selection.
If there are multiple trays that match those criteria for automatic tray selection, a tray is
selected based on the settings for [Tray Priority] on the control panel.
In addition, if [None] is specified for [Specify Paper Type], a tray is selected based on the
settings of [Paper Priority] on the control panel. If the same priority is not assigned to more
than one paper type, a tray is selected based on the settings of [Tray Priority].
Note
• If there are no paper trays that match the automatic tray selection, an error message prompting for
replenishment of paper will be displayed. You can configure the printer not to display this message but to
automatically select a nearest or larger paper size of the document for printing. (Substitute Tray)
• If paper runs out during printing, a paper tray containing paper of the same size and orientation of the
paper used for printing will be selected to continue printing (automatic tray switching). If [None] is
specified for [Specify Paper Type], the paper types that have not been specified for [Paper Priority] are
excluded from the options of the automatic tray selection and automatic tray switching.
• You can also specify the paper tray priority in CentreWare Internet Services.
• If there are no paper trays that match the paper types that are specified for [Specify Paper Type], a
message prompting to confirm printing on another paper type will be displayed. Press the <Eject/Set>
button to print on paper of another type or press the <Cancel Job> button to cancel the job.
Refer to
• Configuring control panel settings: “Printer Settings” (P. 89)
• Specify Paper Type: Online help for the printer driver
62
3 About Paper
3.3
Setting Custom Paper Sizes
When printing on custom size paper, register the paper size in the printer driver.
Setting on the control panel is also required to print custom size paper loaded in trays 1 to 4.
This section explains how to configure the size on the control panel.
For details on registration on the printer driver, refer to “Setting Custom Paper Sizes”
(P. 29).
Important
• When setting the paper size on the printer driver and control panel, be sure to specify the same size as
the actual paper used. Setting the wrong size for printing will cause machine failure. This is especially
true if you configure a bigger size when using a narrow width paper.
Note
• When loading custom size paper in the bypass tray (optional), it is not necessary to specify the size on
the control panel.
• To return to standard paper size settings, select [Auto] in step 6 below. This printer will automatically
detect the size and orientation of the loaded paper.
1.
Press the <Menu> button to display the [Menu] screen.
2.
Press the < > or < > button until [Admin Menu] is displayed, then press the < >
button.
3.
Press the < > or < > button until [Printer Settings] is displayed, then press the < >
button.
4.
Press the < > or < > button until [Paper Size] is displayed, then press the < >
button.
5.
Press the < > or < > button until the required tray is displayed, then press the < >
button.
6.
Press the < > button to display [Custom], then press the <Eject/Set> button.
7.
Press the < > or < > button to display [Portrait (Y) Size] or [Landscape (X) Size],
then press the < > button.
Enter values for the paper size to be used by pressing the < > or < > button.
8.
Press the <Eject/Set> button.
9.
Press the <Menu> button.
3.3 Setting Custom Paper Sizes
63
3.4
Setting Paper Types
Prior settings on the control panel are required for the types of paper loaded in trays 1 to 4.
For accurate image quality processing, refer to the following table and set the paper types
on the control panel.
Important
• Paper type settings must match those of the actual paper loaded in the trays. Otherwise, image quality
cannot be processed accurately. Toner may not fuse properly on the paper, resulting in dirty and poor
quality printouts.
• Changes in paper type settings on the printer driver are not reflected in this printer.
Refer to
• Paper and paper types that can be loaded: “Usable Paper” (P. 55)
Paper name
Weight
Paper type set in tray
FX P
60 - 90 g/m2
Plain (default)
FX EPR, FX R
60 - 90 g/m2
Recycled
Label, envelope,
Japanese official postcard
90 - 156 g/m2
Heavyweight 1
157 - 216 g/m2
Heavyweight 2
-
Transparency
JE001
Setting on the Control Panel
64
1.
Press the <Menu> button to display the [Menu] screen.
2.
Press the < > or < > button until [Admin Menu] is displayed, then press the < >
button.
3.
Press the < > or < > button until [Printer Settings] is displayed, then press the < >
button.
4.
Press the < > or < > button until [Paper Type] is displayed, then press the < >
button.
5.
Press the < > or < > button until the required tray is displayed, then press the < >
button.
6.
Press the < > or < > button until the correct paper type is displayed for the loaded
paper, then press the <Eject/Set> button.
7.
Press the <Menu> button.
3 About Paper
4
Settings on the Control Panel
4.1
Overview of the Common Menu
Menu Configuration
There are two types of menus: common menu and mode menu.
The common menu is the menu from which you can set the common items for all print
modes. The mode menu is the menu from which you can set the specific items for each print
mode.
The common menu has the following structure:
• Common menu > Menu items > Items > Candidate value
The following diagram shows some parts of the common menu structure.
Menu
Meter Reading
Admin Menu
Network/Port
Parallel
Meter 1
Meter 2
Meter 3
Port Status
Print Mode
Enable
Disable
Auto
PCL
System Settings
Common menu
Menu item
Item
Candidate value
4.1 Overview of the Common Menu
65
The common menu has the following items:
Common menu
Print Language
Content
Contains the mode menus used for the HP-GL, HP-GL/2, or PCL emulation
mode settings and for the PDF file direct printing feature settings.
Note
• Refer to “Print Language” (P. 71) for the items to be configured for the PCL
emulation mode and the PDF file direct printing feature. Refer to
“Changing Menu Settings” (P. 67) for basic operations.
• For setting items for HP-GL and HP-GL/2 emulation modes, refer to the
Emulation Settings Guide on the Software Pack CD-ROM.
Report/List
The [Report/List] menu is used to print and check the internal data of this
printer such as the emulation mode settings, system settings, error history,
job history, font information, and the total count of outputs.
Refer to
• “6.2 Printing Reports/Lists” (P. 127)
Meter Reading
The [Meter Reading] menu is used to display the printed paper counts on the
control panel.
Refer to
• “Checking Total Printed Pages on Meter” (P. 137)
Admin Menu
The [Admin Menu] is used for the network/port settings, system settings
(such as alarm and low power/sleep mode), print settings, memory settings,
initialization of printer setting values and hard disks, and form data deletion
settings.
Note
• You cannot set values for disabled ports.
• For details on how to set the settings of each admin menu, refer to “Admin
Menu” (P. 76). Refer to “Changing Menu Settings” (P. 67) for basic
operations.
66
4 Settings on the Control Panel
Changing Menu Settings
Basic Operations
Press one of the following buttons to display the menu screen or to set the printer by
browsing though each menu structure.
Ready to print
1.
To display the menu screen, press the <Menu> button at the print screen.
Menu
Print Language
2.
To move between items, press the < > or < > button.
Menu
Admin Menu
3.
To move between structure levels, press the < > or < > button. Press the
< > button to go to the lower level or press the < > button to return to the
upper level.
Admin Menu
Network/Port
Port Status
Enable
4.
Press the <Eject/Set> button to confirm your settings.
The settings that have been confirmed are displayed
with the affix “*”.
Port Status
Enable *
5.
Press the <Menu> button to return to the print screen.
Ready to print
Note
• If you want to change values after you have confirmed them by pressing the <Eject/Set> button (which
has the affix “*”), you need to set them from the start again.
Initializing Configured Values
Display the item you want to initialize and then press both the < > and < > buttons at the
same time.
Once the change process is completed, the factory defaults will be displayed. Press the
<Eject/Set> button to confirm the value.
4.1 Overview of the Common Menu
67
Example: Changing the Low Power/Sleep Mode Settings
This section describes how to set the common menu. In this example, you set the
transitional time to the low power mode to 15 minutes and the time to the sleep mode to 30
minutes.
Ready to print
1.
Press the <Menu> button to display the [Menu] screen.
Menu
Print Language
2.
Press the < > or < > button until [Admin Menu] is displayed.
Menu
Admin Menu
3.
Press the < > button.
Admin Menu
Network/Port
4.
Press the < > or < > button until [System Settings] is displayed.
Admin Menu
System Settings
5.
Press the < > button.
System Settings
Alert Tone
6.
Press the < > or < > button until [Low Power Mode] is displayed.
System Settings
Low Power Mode
7.
Press the < > button. If the current setting is [Enable], go to step
10.
Low Power Mode
Disable *
8.
Press the < > or < > button until [Enable] is displayed.
Low Power Mode
Enable
9.
Press the <Eject/Set> button. This confirms the low power
mode setting and “*” is displayed.
Low Power Mode
Enable *
10. Press the <
> button to return to [Low Power Mode].
System Settings
Low Power Mode
11. Press the < > or < > button until [Low Power Timer] is
displayed.
Continued on next page
68
4 Settings on the Control Panel
Continued from previous page
System Settings
Low Power Timer
12. Press the < > button.
Low Power Timer
5 Mins *
13. Press the < > or < > button to set the transitional
time to the low power mode. The available setting
values range from 5 to 30 minutes in increments of 1
minute.
Low Power Timer
15 Mins
14. Press the <Eject/Set> button. This sets the transitional
time to the low power mode and “*” is displayed.
Low Power Timer
15 Mins *
15. Press the <
> button to return to [Low Power Timer].
System Settings
Low Power Timer
16. Press the < > button to display [Sleep Mode].
System Settings
Sleep Mode
17. Press the < > button. If the current setting is
[Enable], go to step 20.
Sleep Mode
Disable *
18. Press the < > or < > button until [Enable] is
displayed.
Sleep Mode
Enable
19. Press the <Eject/Set> button. This confirms the
sleep mode setting and displays “*”.
Sleep Mode
Enable *
20. Press the < > button to return to [Sleep
Mode].
System Settings
Sleep Mode
21. Press the < > or < > button until [Sleep
Mode Timer] is displayed.
Continued on next page
4.1 Overview of the Common Menu
69
Continued from previous page
System Settings
Sleep Mode Timer
22. Press the < > button.
Sleep Mode Timer
10 Mins *
23. Press the < > or < > button to set
the transitional time to the sleep mode.
The available setting values range
from 5 to 30 minutes in increments of 1
minute.
Sleep Mode Timer
30 Mins
24. Press the <Eject/Set> button. This
sets the transitional time to the sleep
mode and displays “*”.
Sleep Mode Timer
30 Mins *
25. Press the <Menu> button.
Ready to print
70
4 Settings on the Control Panel
4.2
Description of Menu Items
This section describes the items that can be configured for [Print Language] and [Admin
Menu].
Note
• Refer to “Checking Total Printed Pages on Meter” (P. 137) for the details of [Meter Reading].
• Refer to “6.2 Printing Reports/Lists” (P. 127) for the details of [Report/List].
• Refer to “Changing Menu Settings” (P. 67) for details on how to set menu.
• Detailed settings are available with CentreWare Internet Services. For details, refer to the Online Help
for the CentreWare Internet Services.
Print Language
[Print Language] contains the mode menus used for the HP-GL, HP-GL/2, or PCL emulation
mode settings and for the PDF file direct printing feature settings.
HPGL
For the items that can be set with this menu, refer to the HP-GL, HP-GL/2 Emulation
Settings Guide on the Software Pack CD-ROM bundled with this printer.
PDF
Makes settings for printing PDF file by sending it directly to a printer.
In [Process Mode], select whether to use PDF Bridge or the PostScript feature when
printing PDF files.
The settings of [Process Mode], [Quantity], [2 Sided], [Print Mode], [Password], [Collated],
[Output Size], and [Layout] are available only for printing a PDF file without using
ContentsBridge Utility (Utility software is supplied by Fuji Xerox).
Refer to
• “2.8 Direct Printing of PDF File” (P. 40)
Process Mode
Selects the mode for printing PDF files.
Note
• Printing results may be different between when you select [PDF Bridge] and [PS].
• When you select [PS], [Layout] is not displayed.
[PDF Bridge] (default)
Uses the PDF Bridge feature to process PDF files.
[PS]
Uses Adobe PostScript features to process PDF files.
Quantity
Specifies the copies to be printed between 1 to 999. The default is [1 Sets].
Note
• Depending on the protocol used for sending files, the settings of the protocol may overwrite the settings
you specify here.
4.2 Description of Menu Items
71
2 Sided
Makes settings for 2 sided printing.
Note
• You can set this item only when the duplex unit (optional) is installed.
[Off] (default)
Select this when you do not want to perform 2 sided printing.
[Long Edge Flip]
Select this to print a document so that the printed characters face toward you when paper
is flipped along the long edge.
[Short Edge Flip]
Select this to print a document so that the printed characters face toward you when paper
is flipped along the short edge.
Print Mode
Sets whether to have high quality or high speed.
[Normal] (default)
Select this to print documents at normal speed and normal quality.
[High Quality]
Selecting this decreases printing speed but prints images at high quality.
[High Speed]
Select this to print documents at high speed.
Password* No. 1, 2, 3, and 4 of 4 are available (refer to P. 95).
If a password has been assigned to the PDF file, specify the password here in advance.
Printing will be performed only when the password assigned to the PDF file to be printed
matches the password specified here.
You can input up to 32 alphanumeric characters.
Collated
Select this to set whether to collate multiple copies of the printout by sets (sorted in the order
of page 1, 2, 3,...1, 2, 3...).
The default is [Off].
Output Size
Specifies the paper size to be output.
[A4] (default)
Select this to print on A4-size paper.
[Auto]
Select this to print on a paper size that is automatically determined according to the size
and settings of the PDF file to be printed.
72
4 Settings on the Control Panel
Layout
Select this to set the print layout.
Note
• This item will not be displayed when [PS] has been selected for [Process Mode].
[Auto %] (default)
Select this option to automatically set the magnification percentage so that the
magnification ratio to the paper size for printing will become the largest. Based on the
document size of the PDF file, the printer will determine whether it is A4 or letter size before
printing.
[100% (No Zoom)]
Select this to print documents in the original size regardless of the paper size used for
printing.
[Booklet]
Select this to print the pages on both sides of the paper and arranged like a booklet
according to the page structure of a PDF file. However, booklet printing may not be available
depending on the page structure. In this case, [Auto %] is selected before printing.
Note
• If the duplex unit (optional) is not installed, documents are printed on 1 side.
• If [A4] is specified for [Output Size], the document will be printed on A4 size paper.
• If [Auto] is specified for [Output Size], the document will be printed on A3 or A4 size paper.
[2 Up]
Select this to arrange and print two pages on a single sheet of paper. When [4 Up] is
selected, the paper size is fixed to A4.
[4 Up]
Select this to arrange and print four pages on a single sheet of paper. When [4 Up] is
selected, the paper size is fixed to A4.
4.2 Description of Menu Items
73
PCL
Sets the PCL emulation mode.
Paper Tray
Specifies the paper tray to be used for printing.
Candidate values are as follows:
[Auto] (default)
This searches for the tray loaded with the paper size specified in [Output Size] and
automatically feeds paper from it.
[Tray 1]
[Tray 2]
[Tray 3]
[Tray 4]
[Tray 1 (Bypass)]
Important
• If any tray from [Tray 1] to [Tray 4] is selected, the paper size loaded in the tray will become the paper
size for printing.
Note
• If [Auto] is selected and paper of the same size is loaded in multiple trays in the same direction, paper
will be fed from the tray specified as higher priority in [Tray Priority] under [Printer Settings] of [Admin
Menu]. The default of [Tray Priority] is Tray 1 (highest priority) > Tray 2 > Tray 3 (optional) > Tray 4
(optional) (lowest priority). If paper of the same size is loaded in multiple trays in different directions,
paper loaded in landscape direction will be used first.
• [Tray 3] and [Tray 4] will not be displayed when those optional trays are not installed.
• [Tray 1 (Bypass)] will be displayed only when the bypass tray (optional) is installed. If it is displayed, you
cannot specify [Tray 1].
Output Size
Specifies the paper size to be printed.
Candidate values are as follows:
[A4]
[A3] [A5] [B4] [B5]
[8.5×14] (Legal)
[8.5×11] (Letter)
Output Size (Bypass)
Specifies the paper size to be loaded in the bypass tray (optional).
Candidate values are as follows:
[A4] (default)
[A3] [A5] [B4] [B5]
[8.5×14] (Legal) [8.5×11] (Letter) [8.5×13] [11×17] [7.25×10.5]
Output Tray
Specifies the output tray for printed paper.
[Center Tray] (default)
[Rear Tray]
[OffsetCatchTray]
Note
• [Rear Tray] is available only when the rear tray (optional) is installed.
• [OffsetCatchTray] is available only when the offset catch tray (optional) is installed.
74
4 Settings on the Control Panel
Orientation
The paper printing direction can be selected from [Portrait] and [Landscape]. The default is
[Portrait].
2 Sided Print
Specifies whether to perform 2 sided printing. The default is [Off].
When you select [On], you can select [Long Edge Flip] or [Short Edge Flip] as the binding
direction.
Note
• You can set this item only when the duplex unit (optional) is installed.
Font
Specifies the font used. The default is [Courier].
Symbol Set
Specifies the font for symbols. The default is [ROMAN-8].
Font Size
Specifies the font size. The default is [12.00]. You can specify a value between 4.00 and
50.00 in increments of 0.25.
Font Pitch
Specifies the character spacing. The default is [10.00]. You can specify a value between
6.00 and 24.00 in increments of 0.01.
Form Lines
Specifies the form line (the number of lines per form). The default is [64]. You can specify
a value between 5 and 128 in increments of 1.
Quantity
Specifies the copies to be printed between 1 to 999. The default is [1 Sets].
ImageEnhance
Selects whether to perform image enhancement.
Image enhancement is a feature that makes the boundary line between black and white
smoother to decrease jags and enhance the visual appearance. The default is [On].
HexDump
Specifies whether to print the data sent from a computer in the ASCII code corresponding
to the hexadecimal notation format in order to check the data contents. The default is
[Disable].
Draft Mode
Specifies whether to print in draft mode. The default is [Disable].
Line Termination
Sets the line termination. The default is [Off].
4.2 Description of Menu Items
75
Admin Menu
The [Admin Menu] is used for the network/port settings, system settings (for alarm, power
saver mode, and machine clock, etc.), printer settings, allocate memory settings,
initialization of printer setting values and hard disks, and form data deletion settings.
Network/Port
The [Network/Port] menu is used to set the type of the printer interface connected to a
computer and the necessary conditions for its communications.
Parallel
Select this to use a parallel port.
„ Port Status
Specifies whether to enable or disable the parallel port when the printer turns on. The
default is [Enable], which means the parallel port is available.
Important
• If the memory is running out, you need to disable the port(s) you are not using or change the memory
allocation from [Allocate Memory].
„ Print Mode*1 (refer to P. 95)
Sets the print data process method (printer language to be used).
[Auto] (default)
Select this to make the printer automatically detect the printer language being used in the
data received from a computer and perform printing based on the detected data.
[PCL] [PS] [HP-GL/2] [TIFF]
Select this to process the data received from the computer as the specified data type. [PS]
is displayed when the PostScript software kit (optional) is installed.
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, it
should be set to [Enable]. The default is [Enable].
„ Adobe Protocol
Specifies the communications protocol for PostScript. This item is displayed when the
PostScript software kit (optional) is installed.
[Normal] (default)
Select this when the communications protocol is in ASCII format.
[Binary]
Select this when the communications protocol is in binary format. Selecting this may cause
the printing process to be faster than [Normal] depending on the printing data.
[TBCP]
Select this when you have to switch between ASCII and binary formats by using specific
control codes because they are both used as the communications protocol.
Note
• Select an option according to the data format output from the printer driver in a computer.
• Generally, accept the default setting, [Normal].
• This setting is only available when PostScript is used for printing.
76
4 Settings on the Control Panel
„ Auto Eject Time*3 (refer to P. 95)
Sets the interval for the printer to automatically print the remaining data when no further data
is received for a continuous period.
The time can be set between 5 to 1275 seconds in increments of 5 seconds. The default is
[30 Secs]. When no data is received for the period specified here after the last data was
received, the printer determines it as job end.
„ Bi-directional
Specifies whether to enable or disable the bi-directional communication (IEEE1284) of the
parallel interface. The default is [Enable].
Serial
Select this to use a serial port.
Important
• When using the serial port, it is necessary to accommodate the port setting of the printer driver to that of
the printer. For details, refer to “Appendix A.7 Printing Using the Serial Interface” (P. 158)
„ Port Status
Specifies whether to enable or disable the serial port when the printer turns on. The default
is [Enable], which means the serial port is available.
„ Print Mode*1 (refer to P. 95)
Sets the print data process method (printer language to be used).
[Auto] (default)
Select this to make the printer automatically detect the printer language being used in the
data received from the computer and perform printing based on the detected data.
[PCL] [PS] [HP-GL/2] [TIFF]
Select this to process the data received from the computer as the specified data type.
Note
• [PS] is displayed only when the PostScript software kit (optional) is installed.
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, it
should be set to [Enable]. The default is [Enable].
„ Adobe Protocol
Specifies the communications protocol for PostScript. This item is displayed only when the
PostScript software kit (optional) is installed.
[Normal] (default)
Select this when the communications protocol is ASCII format.
[Binary]
Select this when the communications protocol is in binary format. Selecting this may cause
the printing process to be faster than [Normal] depending on the printing data.
[TBCP]
Select this when you have to switch between ASCII and binary formats by using specific
control codes because they are both used as the communications protocol.
Note
• Select an option according to the data format output from the printer driver in the computer.
• Generally, accept the default setting, [Normal].
• This setting is only available when PostScript is used for printing.
4.2 Description of Menu Items
77
„ Auto Eject Time*3 (refer to P. 95)
Sets the time interval for the printer to automatically print the remaining data when no further
data is received for a continuous period.
The time can be set between 5 to 1275 seconds in increments of 5 seconds. The default is
[30 Secs]. When no data is received for the period specified here after the last data was
received, the printer determines it as job end.
„ Baud rate
Sets the baud rate. Select from [9600bps] [19200bps] [38400bps] [57600bps] [115200bps]
[4800bps]. The default is [9600bps].
„ Stop Bit
Select the stop bit from [1 bit] or [2 bits]. The default is [1 bit].
„ Parity
Sets the parity. Select from [Not Available] [Odd] [Even]. The default is [Not Available].
„ XON - XOFF Control
Sets whether to enable or disable the XON/XOFF control at the flow control. The default is
[On].
„ DTR Control
Sets the DTR control from [Fix-High] [Fix-Low] [Active-High] [Active-Low]. The default is
[Fix-High].
LPD
Select this to use LPD.
„ Port Status
Specifies whether to enable or disable the LPD port when the printer turns on. The default
is [Enable], which means the LPD port is available.
Note
• To enable the LPD port, the IP address must be specified.
Important
• If the memory is running out when the port is enabled, the port may be disabled automatically. In this
case, you need to disable the port(s) you are not using or change the memory allocation from [Allocate
Memory].
„ Print Mode*1 (refer to P. 95)
Specifies the print data process method (printer language to be used).
[Auto] (default)
Select this to make the printer automatically detect the printer language being used in the
data received from a computer and perform printing based on the detected data.
[PCL] [PS] [HP-GL/2] [TIFF]
Select this to process the data received from a computer as the specified data type. [PS] is
displayed when the PostScript software kit (optional) is installed.
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, it
should be set to [Enable]. The default is [Enable].
78
4 Settings on the Control Panel
„ Connect Time-Out*3 (refer to P. 95)
Specifies the time interval for disconnection when no further data is received. You can
specify a value between 2 and 3600 seconds in increments of 1 second. The default is [16
Secs].
„ TBCP Filter
Specifies whether to enable or disable the TBCP filter when processing PostScript data.
This item is displayed when the PostScript software kit (optional) is installed. The default is
[Disable].
„ Port No.
Sets 515 or a value between 8000 and 9999 for the port number. The default is [515].
NetWare
Select this to use NetWare.
„ Port Status
Specifies whether to enable or disable the NetWare port when the printer turns on. The
default is [Disable]. To use NetWare, select [Enable].
Important
• If the memory is running out when the port is enabled, the port may be disabled automatically. In this
case, you need to disable the port(s) you are not using or change the memory allocation from [Allocate
Memory].
„ Transport Protocol
Specifies the transport protocol used for NetWare. IPX/SPX, TCP/IP, or both protocols can
be specified. The default is [TCP/IP,IPX/SPX].
Note
• When using TCP/IP, both the IP addresses of a computer and the printer are required.
„ Print Mode*1 (refer to P. 95)
Specifies the print data process method (printer language to be used).
[Auto] (default)
Select this to make the printer automatically detect the printer language being used in the
data received from a computer and perform printing based on the detected data.
[PCL] [PS] [HP-GL/2] [TIFF]
Select this to process the data received from a computer as the specified data type. [PS] is
displayed only when the PostScript software kit (optional) is installed.
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, it
should be set to [Enable]. The default is [Enable].
„ No. of Searches*3 (refer to P. 95)
Specifies how many times the file server is searched.
Specify a value between 1 and 100 in increments of 1, or select [No Limit]. The search
interval is 1 minute. The default is [No Limit].
4.2 Description of Menu Items
79
„ TBCP Filter
Specifies whether to enable or disable the TBCP filter when processing PostScript data.
This item is displayed when the PostScript software kit (optional) is installed. The default is
[Disable].
SMB
Select this to use SMB.
„ Port Status
Specifies whether to enable or disable the SMB port when the printer turns on. The default
is [Enable], which means the SMB port is available.
Important
• If the memory is running out when the port is enabled, the port may be disabled automatically. In this
case, you need to disable the port(s) you are not using or change the memory allocation from [Allocate
Memory].
„ Transpt Protocol
Specifies the transport protocol used for SMB. NetBEUI, TCP/IP, or both protocols can be
specified. The default is [TCP/IP].
Note
• When using TCP/IP, both the IP addresses of a computer and the printer are required.
„ Print Mode*1 (refer to P. 95)
Sets the print data process method (printer language to be used).
[Auto] (default)
Select this to make the printer automatically detect the printer language being used in the
data received from a computer and perform printing based on the detected data.
[PCL] [PS] [HP-GL/2] [TIFF]
Select this to process the data received from a computer as the specified data type. [PS] is
displayed only when the PostScript software kit (optional) is installed.
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, it
should be set to [Enable]. The default is [Enable].
„ TBCP Filter
Specifies whether to enable or disable the TBCP filter when processing PostScript data.
This item is displayed only when the PostScript software kit (optional) is installed. The
default is [Disable].
80
4 Settings on the Control Panel
IPP
Select this to use IPP.
„ Port Status
Specifies whether to enable or disable the IPP port when the printer turns on. The default
is [Disable]. To use IPP, select [Enable] for this setting.
Note
• To enable the IPP port, IP address must be specified.
Important
• If the memory is running out when the port is enabled, the port may be disabled automatically. In this
case, you need to disable the port(s) you are not using or change the memory allocation from [Allocate
Memory].
„ Print Mode*1 (refer to P. 95)
Specifies the print data process method (printer language to be used).
[Auto] (default)
Select this to make the printer automatically detect the printer language being used in the
data received from a computer and perform printing based on the detected data.
[PCL] [PS] [HP-GL/2] [TIFF]
Select this to process the data received from a computer as the specified data type. [PS] is
displayed only when the PostScript software kit (optional) is installed.
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, it
should be set to [Enable]. The default is [Enable].
„ Access Control
Specifies whether to enable or disable the access right control when canceling/deleting a
print job or setting/releasing the printer to/from pause state. The default is [Disable].
„ DNS
Specifies whether to use the name registered in DNS (Domain Name System) in order to
recognize the printer. The default is [Enable], which means the DNS name is available. If
[Disable] is selected, the IP address is used for recognizing the printer.
„ Add Port No.*3 (refer to P. 95)
Specify 0, 80, or a value between 8000 and 9999 for the additional port number. The default
is [80].
„ Connect Time-Out
Specifies the time interval for disconnection when no further data is received. You can
specify a value between 0 and 65535 seconds in increments of 1 second. The default is [60
Secs].
„ TBCP Filter
Specifies whether to enable or disable the TBCP filter when processing PostScript data.
This item is displayed only when the PostScript software kit (optional) is installed. The
default is [Disable].
4.2 Description of Menu Items
81
EtherTalk
Select this to use EtherTalk. This item is displayed only when the PostScript software kit
(optional) is installed.
„ Port Status
Specifies whether to enable or disable the EtherTalk port when the printer turns on. The
default is [Disable]. To use EtherTalk, select [Enable] for this setting.
Important
• If the memory is running out when the port is enabled, the port may be disabled automatically. In this
case, you need to disable the port(s) you are not using or change the memory allocation from [Allocate
Memory].
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, select
[Enable] for this setting. The default is [Enable].
USB
Select this to use USB ports.
„ Port Status
Specifies whether to enable or disable the USB port when the printer turns on. The default
is [Enable], which means the USB port is available.
Important
• If the memory is running out, you need to disable the port(s) you are not using or change the memory
allocation from [Allocate Memory].
„ Print Mode*1 (refer to P. 95)
Specifies the print data process method (printer language to be used).
[Auto] (default)
Select this to make the printer automatically detect the printer language being used in the
data received from a computer and perform printing based on the detected data.
[PCL] [PS] [HP-GL/2] [TIFF]
Select this to process the data received from a computer as the specified data type. [PS] is
displayed only when the PostScript software kit (optional) is installed.
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, select
[Enable] for this setting. The default is [Enable].
„ Auto Eject Time*3 (refer to P. 95)
Sets the time interval for the printer to automatically print the remaining data when no further
data is received for a continuous period.
The time can be set between 5 to 1275 seconds in increments of 5 seconds. The default is
[30 Secs]. When no data is received for the period specified here after the last data was
received, the printer determines it as job end.
82
4 Settings on the Control Panel
„ Adobe Protocol
Specifies the communications protocol for PostScript. This item is displayed only when the
PostScript software kit (optional) is installed.
[Normal] (default)
Select this when the communication protocol is in ASCII format.
[Binary]
Select this when the communication protocol is in binary format. Selecting this may cause
the printing process to be faster than [Normal] depending on the printing data.
[TBCP]
Select this when you have to switch between ASCII and binary formats by using specific
control codes because they are both used as the communication protocol.
Note
• Select an option according to the data format output from the printer driver in a computer.
• Generally, accept the default setting, [Normal].
• This setting is only available when PostScript is used for printing.
Port9100
Select this to use Port9100.
„ Port Status
Specifies whether to enable or disable the Port9100 port when the printer turns on. The
default is [Enable], which means the Port9100 port is available.
Note
• To enable the Port9100 port, the IP address must be set.
Important
• If the memory is running out when the port is enabled, the port may be disabled automatically. In this
case, you need to disable the port(s) you are not using or change the memory allocation from [Allocate
Memory].
„ Print Mode*1 (refer to P. 95)
Sets the print data process method (printer language to be used).
[Auto] (default)
Select this to make the printer automatically detect the printer language being used in the
data received from a computer and perform printing based on the detected data.
[PCL] [PS] [HP-GL/2] [TIFF]
Select this to process the data received from a computer as the specified data type. [PS] is
displayed only when the PostScript software kit (optional) is installed.
„ PJL*2 (refer to P. 95)
This printer supports PJL commands that are independent from any printer languages. The
PJL commands are used to control print jobs and are required for printing using a printer
driver. In this menu, specify whether to enable or disable the PJL commands sent from a
computer. PJL commands allow you to specify the printer language to be used for the next
data even while the printer is using a different printer language at the time. Normally, select
[Enable] for this setting. The default is [Enable].
„ Connect Time-Out*3 (refer to P. 95)
Specifies the interval for disconnection when no further data is received. You can specify a
value between 2 and 65535 seconds in increments of 1 second. The default is [60 Secs].
„ Port No.
Sets the port number to 9100 or a value between 8000 and 9999. The default is [9100].
4.2 Description of Menu Items
83
„ TBCP Filter
Specifies whether to enable or disable the TBCP filter when processing PostScript data.
This item is displayed only when the PostScript software kit (optional) is installed. The
default is [Disable].
UPnP
Makes settings fpr UPnP (Universal Plug and Play).
„ Port Status
Specifies whether to enable or disable the UPnP when the printer turns on. The default is
[Disable].
Important
• If the memory is running out when the port is enabled, the port may be disabled automatically. In this
case, you need to disable the port(s) you are not using or change the memory allocation from [Allocate
Memory].
SNMP
Configure these settings to use SNMP. SNMP settings are required to use the application
that remotely controls multiple printers. The printer information is maintained in SNMP. The
application obtains the printer information from the SNMP.
„ Port Status
Specifies whether to enable or disable the SNMP port when the printer turns on. The default
is [Enable], which means the SNMP port is available.
Important
• If the memory is running out when the port is enabled, the port may be disabled automatically. In this
case, you need to disable the port(s) you are not using or change the memory allocation from [Allocate
Memory].
„ Transpt Protocol
Specifies the transport protocol used for SNMP. IPX, UDP, or both protocols can be
specified. The default is [UDP].
Note
• When using UDP, both the IP addresses of a computer and the printer are required.
• Refer to the application’s manual for the protocol to be used: IPX or UDP.
„ Community (R)* No.1 to 3 characters of 4 are available (refer to P. 95)
Specify the community name used for reading the printer management information (MIB)
with up to 12 alphanumeric characters. The default is [Unregistered].
„ Community (R/W)* No.1 to 3 characters of 4 are available (refer to P. 95)
Specify the community name used for reading/writing the printer management information
(MIB) with up to 12 alphanumeric characters. The default is [Unregistered].
„ Community (Trap)* No.1 to 3 characters of 4 are available (refer to P. 95)
Specify the community name used for trapping with up to 12 alphanumeric characters. The
default is [Unregistered].
84
4 Settings on the Control Panel
TCP/IP Settings
„ Get IP Address
Specifies whether to automatically or manually retrieve the necessary information for using
TCP/IP (IP address, subnet mask, and gateway address) from the DHCP (Dynamic Host
Configuration Protocol) server with AutoIP feature, DHCP server, BOOTP, or RARP. For
the addresses you need to set manually, contact your network administrator. The default is
[DHCP/Autonet].
Note
• Changing the setting from [DHCP/Autonet], [DHCP], [BOOTP], or [RARP] to [Manual] may display the IP
address setting screen. If it appears, specify the IP address manually.
„ IP Address, Subnet Mask, Gateway Address*3 (refer to P. 95)
These items are used to check the addresses that have been obtained automatically or to
specify addresses manually. Enter the address in the format of xxx.xxx.xxx.xxx. You can
specifies values in the range of 0 to 255 for xxx.
Important
• Incorrect IP address may affect the overall network.
• If you enter an incorrect address when setting the subnet mask (e.g. when “0” is set for the bit in the
middle), the address returns to the previous values even if you press the <Menu> button after setting
values. You cannot move to other menu items until you have set the correct values.
• Set the address only when you have to explicitly specify the gateway address. You do not need to set
the address if the gateway address can be set automatically.
InternetServices
Specifies whether to use Internet Services.
When [Enable] is specified, you can use CentreWare Internet Services to display the printer
and job status on a web browser and change the printer settings. The default is [Enable].
Note
• To enable Internet Services, you need to specify both the IP addresses of a computer and the printer.
WINS Server
„ Get DHCP Address
Specifies whether to automatically retrieve the IP address of WINS server that is required
for using WINS (Windows Internet Name Service). If you do not select automatic retrieval
of the IP address, contact your network administrator for manual specification of the
addresses. The default is [On].
Note
• Changing from [On] to [Off] may display the IP address setting screen. If it appears, specify the IP
address manually.
„ Primary IP, Secondary IP*3 (refer to P. 95)
These items are used to check the addresses that have been automatically obtained or to
specify the addresses manually. Enter the address in the format of xxx.xxx.xxx.xxx. You can
set values between 0 and 255 for xxx. If the primary IP address is invalid, the secondary IP
address will become invalid too.
Important
• Incorrect IP address may affect the overall network.
4.2 Description of Menu Items
85
Ethernet
Specifies the communication speed/connector type of the Ethernet interface.
[Auto] (default)
Select this to switch between 100BASE-TX and 10BASE-T automatically.
[100BASE-TX]
Select this to use 100BASE-TX only.
[10BASE-T]
Select this to use 10BASE-T only.
IPX/SPX Frame Type
Specifies the operational frame type of IPX/SPX.
[Auto] (default)
Select this to automatically configure the frame type.
[Ethernet II]
Select this to use the Ethernet frame type.
[Ethernet 802.3]
Select this to use the IEEE802.3 frame type.
[Ethernet 802.2]
Select this to use the IEEE802.3/IEEE802.2 frame type.
[Ethernet SNAP]
Select this to use the IEEE802.3/IEEE802.2/SNAP frame type.
Filter
„ IP Filter
Specifies whether to limit IP addresses that receive print jobs. Select [On] if you do not want
to receive print jobs from non-registered IP addresses. The default is [Off].
Note
• Even if [On] is selected, it becomes invalid when all the registered IP addresses are “000.000.000.000”.
„ IP Address*3 (refer to P. 95)
Registers the IP addresses that are allowed to receive jobs if you want to limit the IP
addresses. You can specify up to 10 IP addresses. Specify the address masks for the
registered IP addresses. Enter the IP addresses and address masks in the format of
xxx.xxx.xxx.xxx. You can set values between 0 and 255 for xxx. For example, if you specify
“126.249.110.23” in [IP address] and “255.255.255.0” in [IP Address Mask], the addresses
that are allowed to receive jobs are “129.249.110.* (1 to 254)”.
System Settings
[System Settings] menu is used to make the printer operation settings such as for alarm and
power saver mode.
Alert Tone
Specifies whether to turn on the alarm when an error occurs in the printer. The default is
[Off]. You cannot adjust the sound volume.
86
4 Settings on the Control Panel
Panel Settings*3 (refer to P. 95)
„ Panel Lock
Specifies whether to limit the menu operations with a password. Selecting [On] requires the
operator to enter the password. The default is [Off].
Note
• If [On] is selected but the password is not specified, the password setting screen will be displayed. Enter
a 12-digit number as the password by pressing the < > and < > buttons. You can move between
digits with the < > and < > buttons.
• You cannot specify “000000000000” as the password.
„ Change Password
You can change the password for control panel limitations. Enter the current password
(12-digit number) to display the password input screen. Specify the new password.
Note
• If [On] is not selected for [Panel Lock], the password cannot be changed.
OfflineAutoClear*3
(refer to P. 95)
Specifies whether to automatically turn off the offline status. Select [Off] or specify the time
to turn off the offline status between 1 and 30 minutes in increments of 1 minute. The default
is [Off].
Low Power Mode
The low power mode is a feature that reduces the printer’s power consumption by
automatically decreasing the temperature of the fuser after a period of time. This item
specifies whether to use this feature. The default is [Enable].
Note
• If [Disable] is specified for [Sleep Mode], you cannot select [Disable] for [Low Power Mode].
Refer to
• “Example: Changing the Low Power/Sleep Mode Settings” (P. 68)
Low Power Timer
Specify the transitional time to low power mode between 5 and 30 minutes in increments of
1 minute. Once the low power mode is turned on, the display of the control panel is turned
off and the lamp of the <Power Saver> button is lit. The default is [5 Mins].
Refer to
• “Example: Changing the Low Power/Sleep Mode Settings” (P. 68)
Sleep Mode
The sleep mode is a feature that reduce the printer’s power consumption more effectively
than low power mode. This item specifies whether to use this feature. The default is
[Enable].
Note
• If [Disable] is specified for [Low Power Mode], you cannot select [Disable] for [Sleep Mode].
Refer to
• “Example: Changing the Low Power/Sleep Mode Settings” (P. 68)
4.2 Description of Menu Items
87
Sleep Mode Timer*3
(refer to P. 95)
Specify the transitional time to sleep mode between 5 and 30 minutes in increments of 1
minute. Once the power saver mode is turned on, the display of the control panel is turned
off and the lamp of the <Power Saver> button is lit. The default is [10 Mins].
Refer to
• “Example: Changing the Low Power/Sleep Mode Settings” (P. 68)
Auto Job History
Specifies whether to automatically print information about the printed data that has been
processed in the printer ( [Job History Report] ).
[Do not print] (default)
Select this if you do not want to print the [Job History Report] automatically.
[Print]
Select this to print a report on the oldest 50 data histories that have not been output yet
when the memory capacity is full. This does not include the print data in processing or in
queue.
2 Sided Report
Specifies whether to print reports/lists on 1 side or 2 sides of the paper when the 2 sided
printing function is available in the printer.
[1 Sided] (default)
[2 Sided]
Print Area
Specfies whether to expand the printable area. The default is [Normal].
Banner Sheet
„ Banner Output
Specifies whether to output the banner sheet. If you want to output it, specify whether to
output it at the beginning of, at the end of, or at the beginning and end of the document.
„ Banner Tray
Specifies the tray from which the banner sheet is output from trays 1 to 4.
Secure Print
Specifies whether to use the secure print feature.
[Enable] (default)
Select this to use the secure print feature.
[Disable]
Select this to prohibit secure print.
Note
• This item is displayed when the hard disk (optional) is installed.
Machine Clock*3 (refer to P. 95)
Specifies the date (day/month/year) (for year, enter a number between 2000 and 2099) and
time (hour/minute) (for hours, enter a number in 24-hour format) of the printer system clock.
The date/time specified here will be printed on reports and lists.
„ Set Date
Enter the date in the format of “dd/mm/yy” (e.g. 01/01/2002).
88
4 Settings on the Control Panel
„ Set Time
Enter the time in the format of “hh/mm” (e.g. 12/02).
„ Date Format
Select the date display order from “yyyy/mm/dd” (year/month/day), “mm/dd/yyyy” (month/
day/year), and “dd/mm/yyyy” (day/month/year).
„ Time Format
Select the time display from 12-hour display and 24-hour display.
„ Time Zone
Specify the time zone if required.
„ Daylight Saving, Start Date, End Date
Specify summer time if required.
Drum/Toner Life
When it is about time to replace the drum/toner cartridge, a message will appear on the
display. After the message is displayed, you can continue to print normally for about 100
sheets.
Specify whether to stop printing when the drum/toner cartridge needs to be replaced.
[Cancel Print] (default)
Select this to stop printing after the message notifying that it is about time to replace the
drum/toner cartridge was displayed and until it is replaced with a new one.
[Continue Print]
Select this not to stop printing even when the drum/toner cartridge needs replacing. Note
that continuous printing after the replacement time has passed may affect the print image
quality and the printer performance. It is recommended to install a new drum/toner
cartridge.
mm/inch
Specifies the unit that is used on the control panel from [Millimeter (mm)] and [Inch (")].
The default is [Millimeter (mm)].
Printer Settings
[Printer Settings] menu is used to make settings for paper trays such as the auto tray
selection feature.
Substiture Tray
Specifies whether to print on paper loaded in another tray when there is no paper left in the
tray selected by the auto tray selection feature. If you want to replace paper, specify the
paper size.
[Off] (default)
Select this not to replace paper but display a message prompting you to load paper.
[Larger Size]
Select this to replace the paper with a larger size paper before printing in 100%
magnification ratio.
[Nearest Size]
Select this to replace the paper with the nearest size paper before printing. This may shrink
the images automatically as required.
4.2 Description of Menu Items
89
[Bypass Feed]
Select this to print on paper loaded in the bypass tray. You can select this only when the
bypass tray (optional) is installed.
Note
• If a computer issues the instruction about paper selection, it overwrites this setting.
Paper Type
Specifies the paper type to be loaded in trays. The default is [Plain] for all trays. The names
specified in [Paper Name] will be displayed for Customs 1 to 5.
„ Tray 1 to Tray 4
Select from [Plain], [Recycled], [Heavyweight 1], [Heavyweight 2], [Transparency], and
[Custom 1] to [Custom 5].
„ Tray 1 (Bypass)
Select from [Plain], [Recycled], [Heavyweight 1], [Transparency], and [Custom 1] to
[Custom 5].
Note
• [Tray 1 (Bypass)] will be displayed when the bypass tray (optional) has been installed. If it is displayed,
you cannot specify [Tray 1].
Paper Priority
Specifies the priority of the paper type loaded in the tray specified with the auto tray
selection feature. The names specified in [Paper Name] will be displayed for Customs 1 to
5.
„ Plain, Recycled, Heavyweight 1, Heavyweight 2, Custom 1 to Custom 5
Select the priority of each paper type from [Not Selected] and [1] to [9]. You can specify the
same priority for different paper types. In this case, the paper tray is selected based on the
settings in [Tray Priority]. If you specify [Not Selected] for a paper type, the tray loaded with
the paper type will be excluded from the targets of auto tray selection. The default is [1] for
plain paper, [2] for recycled paper, and [Not Selected] for the others.
Refer to
• “Automatic Tray Selection” (P. 62)
Tray Priority
Specifies the priority of trays 1 to 4 for auto tray selection when the optional trays are
installed. The bypass tray is excluded from the targets of auto tray selection.
„ 1 to 3
Specify a priority of [1] to [3] for each tray. You cannot set the same tray to different priority
numbers. That means the trays that can be set [2] are other than the tray specified in [1],
and the trays that can be set [3] are other than the trays specified in [1] and [2]. The
remaining trays are set to [4]. The default priority is tray 1 (highest priority) to tray 4 (lowest
priority).
90
4 Settings on the Control Panel
Paper Size
Specifies the paper size to be loaded in trays.
Note
• For details on the paper sizes available for each tray, refer to “Usable Paper” (P. 55).
• You cannot configure settings for tray 1 if the bypass tray (optional) is installed.
„ Tray 1 to Tray 4
[Auto] (default)
Select this to load the standard size paper.
[Custom]
Select this to load the custom size paper and specify the [Portrait (Y) Size] and [Landscape
(X) Size] in increments of 1 mm (0.1").
Paper Name
You can change [Custom 1] to [Custom 5] displayed in [Paper Priority] and [Paper Type] to
any names.
„ Custom 1 to Custom 5* No.1 to 3 characters of 4 are available (refer to P. 95)
Specify up to 12 alphanumeric characters.
Job Offset
Specify how to perform offset output. This setting is only available when the offset catch tray
(optional) is installed.
[Offset Per Set] (default)
When printing multiple copies, each set of document is output with its position shifted per
set.
[Offset Per Job]
Select this to output the document with its position shifted per job.
[Off]
Select this if you do not want to perform offset output.
Print ID
Select this to print the user ID on a specified position.
The default is [Off].
Odd Page 2 Sided
Specifies whether to perform 1 sided printing or 2 sided printing for the first page when the
total number of pages is an odd number. This setting is only available when the duplex unit
(optional) is available. The default is [1 Sided].
PaperSelect Mode
Specifies how to select paper when printing PostScript data.
[Auto] (default)
Select this mode when you want to use our PostScript driver. Selecting this will print on the
paper loaded in the tray specified by the printer driver.
[Select from tray]
Some applications create the PostScript program directly without using a printer driver. In
this case, a paper tray may not be selected correctly depending on the application.
Selecting [Select from tray] ensures that data is printed on the specified paper.
4.2 Description of Menu Items
91
DefaultPaperSize
Specifies the default setting of the paper size when using E-mail Printing feature, the paper
size when printing the reports, and the [Output Size] setting of the each print mode to [A4]
or [8.5×11"]. This default is [A4].
Allocate Memory*3 (refer to P. 95)
[Allocate Memory] menu is used to change the capacity of the memory for each interface
and the form memory.
In this printer, you can change the following memory allocation. Note that the allocated
memory type differs depending on the installation status of optional accessories.
Memory types
Standard
PS
PS memory
HPGL auto layout memory
Receive buffer size
Print page buffer
:
:
:
PS:
Available
Not available
Not available when the hard disk (optional) is installed.
PostScript software kit (optional)
Important
• Changing the memory capacity will reset the memory and delete all data stored in each memory area.
• You cannot exceed the overall memory capacity during memory allocation. If the setting value exceeds
the actual memory capacity, the system will automatically adjust it when the printer turns on.
• If the memory is running out when [Enable] is specified for the port, the port may be disabled
automatically. In this case, you need to disable the port(s) you are not using or change the memory
allocation. However, the parallel and USB ports will not stop automatically.
Note
• The memory allocation settings (except the print page buffer setting) are available in the control panel
and CentreWare Internet Services.
• The print page buffer is the area in which the actual print image can be drawn. The print page buffer is
allocated to the remaining area after the memory is allocated to all other uses. Therefore, you cannot
directly change the print page buffer capacity. You can check the actual print page buffer size in [System
Settings List]. You can also check it in CentreWare Internet Services. When you want to print a
high-resolution document, allocate memory so that the print page buffer size is large.
PS
Specifies the memory capacity for PostScript (optional). This item is displayed when the
PostScript software kit (optional) is installed.
Specify the memory capacity between 4.50 and 96.00 MB in increments of 0.25 MB. The
default is [12.00 M]. The maximum capacity you can specify depends on the free memory
capacity.
HPGL Auto Layout
Specifies the memory capacity used for HP-GL, HP-GL/2 auto layout.
Specify the memory capacity between 64 and 5120 KB in increments of 32 KB. The default
is [64K]. The maximum capacity you can specify depends on the free memory capacity.
If the hard disk (optional) is installed, the hard disk memory is used for the auto layout. You
cannot change its capacity. [Hard Disk] is displayed on the screen.
92
4 Settings on the Control Panel
Buffer Size
For each interface, specify the memory capacity of the receive buffer (in which the data sent
from a computer is saved temporarily). For LPD, SMB, and IPP, specify the availability of
spool processing, locations, and memory capacity.
You can change the receive buffer capacity depending on how busy the conditions are and
purposes. Increasing the receive buffer capacity may increase the disconnection speed of
the computer for each interface. The maximum capacity you can specify depends on the
free memory capacity.
Note
• If a port is disabled, the items for it will not be displayed.
• Even if the memory capacity is increased, the disconnection speed of a computer may not be changed
due to the data volume sent from a computer.
„ Parallel, Serial, NetWare Memory, IPP Memory, USB Memory, Port9100 Memory
Specify the memory capacity between 64 and 1024 KB in increments of 32 KB. The default
is [64 K] for parallel and USB memories and [256 K] for the other memories.
Note
• [IPP Memory] is displayed when the hard disk (optional) is not installed. [IPP Spool] is displayed when
the hard disk is installed.
„ EtherTalk Memory
Specify the memory capacity between 64 and 1024 KB (1024 and 2048 KB when the
mounted RAM is 256 MB or more) in increments of 32 KB. The default is [1024K].
Note
• [EtherTalk Memory] is displayed only when the PostScript software kit (optional) is installed.
„ LPD Spool, SMB Spool
[Off] (default)
Select this if you do not want to perform spool processing. When the LPD or SMB data from
a computer is being processed, data from another computer cannot be received via the
same interface.
For LPD, specify the LPD specific receive buffer memory capacity between 64 and 1024 KB
(1024 and 2048 KB when the mounted RAM is 256 MB or more) in increments of 32 KB.
The default is [1024K].
For SMB, specify the SMB specific receive buffer memory capacity between 64 and 1024
KB in increments of 32 KB. The default is [256K].
[Hard Disk]
Select this to perform spool processing. This uses the hard disk (optional) as the receive
buffer for spool processing. This item is displayed when the hard disk is installed.
[Memory]
Select this to perform spool processing. This uses the memory as the receive buffer for
spool processing.
If you select this option, specify the receive buffer memory capacity for spool processing
between 0.5 and 32.00 MB in increments of 0.25 MB. The default is [1.00 M]. Note that the
printer cannot receive data that is larger than the specified memory capacity. In this case,
select [Hard Disk] or [Off].
Important
• If LPR byte count is disabled in Windows 2000 and you send a document whose size is larger than the
spool memory capacity, the computer will repeatedly try to send the job. To stop this, open the [Port] tab
from the properties dialog box of the printer driver to enable the LPR byte count or change the memory
spool capacity to a value larger than the document size.
4.2 Description of Menu Items
93
„ IPP Spool
[Off] (default)
Select this if you do not want to perform spool processing. When IPP data from a computer
is being processed, data from another computer cannot be received via the same interface.
Specify the IPP specific receive buffer memory capacity between 64 and 1024 KB in
increments of 32 KB. The default is [256K].
[Hard Disk]
Select this to perform spool processing. This uses the hard disk (optional) as the receive
buffer for spool processing.
Note
• [IPP Spool] is displayed when the hard disk (optional) is installed. [IPP Memory] is displayed when the
hard disk is not installed.
Init/Del Data
[Init/Del Data] menu is used to delete data such as the printer setting values stored in the
NV memory and the form data registered in this printer. It is also used to initialize the hard
disk and meter reports.
Note
• Initialization will revert each setting value to default. Refer to “4.3 Menu List” (P. 96) for details.
NVM
Select this to initialize the NV memory. The NV memory is a nonvolatile memory that stores
the printer settings even after power off.
Initializing the NV memory will revert the value for each item to default.
Hard Disk
Select this to initialize the hard disk (optional). The data to be deleted during initialization
includes the additional fonts, the HP-GL and HP-GL/2 forms, and the SMB folders. The
secure print documents, sample print documents, delayed print documents, and their logs
will not be deleted. This item is displayed when the hard disk is installed.
Print Meter
Select this to initialize the printer meter reports. Initialization will change the meter count to
“0”.
Refer to
• “Initializing Print Meter Data” (P. 138)
Form
If there are no forms registered, a message saying “Not registered” will be displayed.
„ Delete PCL Forms
Select this to delete the forms for PCL emulation. All the registered PCL forms are deleted.
Font
If there are no registered fonts, “Not registered” message will be displayed.
„ Delete PCL Fonts
Select this to delete the fonts for PCL emulation. All the downloaded PCL fonts are deleted.
94
4 Settings on the Control Panel
Stored Documents
Select this to delete the documents stored for secure print. If there are no such documents,
“No stored documents” will be displayed.
This item is displayed when the hard disk (optional) is installed.
*1
When [Auto] is selected and the printer detects a printer language that is not installed
in this printer or an unsupported printer language, the data will be deleted.
*2
If a printer language that is not installed in this printer is specified by PJL commands,
the data will be deleted.
*3
When you are changing the candidate values by the < > and < > buttons, you can
press and hold down the buttons to change the display continuously. Also, pressing the
< > and < > buttons simultaneously will display the default values.
*4
Character List
No.
Character type
Character
1
Blank
Space
2
Alphabet
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijkl
mnopqrstuvwxyz
3
Numbers
0123456789
4
Symbols
!"#$%&'()*+,-./:;<=>?@[¥]^_`{ | }
4.2 Description of Menu Items
95
4.3
Menu List
For details on each feature, refer to “4.2 Description of Menu Items” (P. 71).
• Main operation and buttons on the control panel
Display/Close the Menu screen
<Menu> button
Switch between the menu levels
< > button (moves one level downwards) or <
button (moves one level upwards)
Switch between menu or items in the
same level
< > button (displays the previous menu or item) or <
button (displays the next menu or item)
Move the cursor (_) of the setting value to
the right or left
< > button (moves to the right) or <
to the left)
Confirm setting
<Eject/Set> button (<Set> button in the following
diagram)
96
4 Settings on the Control Panel
>
> button (moves
Note
•
indicates items that can be configured when optional accessories are installed.
(1): PostScript software kit
(2): Hard Disk
(3): Duplex Unit
(4): A3 Universal Tray
(5): Offset Catch Tray
(6): Rear Tray
(7): Bypass Tray
• * indicates default value.
Continued on next page
>
Continued from previous page
Continued on next page
4.3 Menu List
97
Continued from previous page
98
4 Settings on the Control Panel
From P. 97
From P. 97
4.3 Menu List
99
From P. 97
100
4 Settings on the Control Panel
5
Troubleshooting
5.1
When Paper Jams
CAUTION
• When removing jammed paper, make sure that no pieces of torn paper are left in the
machine. A piece of paper remaining in the machine can cause fire. If a sheet of paper is
wrapped around the heat roller, or when clearing a jammed paper that is difficult or
impossible to see, do not try to remove it by yourself. Doing so can cause injuries or
burns. Switch off the machine immediately, and contact our Customer Support Center or
your dealers.
Following the message on the control panel, open the cover and remove the jammed paper.
If paper is torn, check for any remaining torn pieces of paper.
Cover D (Offset catch tray)
Cover A
When the offset catch tray
(optional) is installed, fold the tray
first before opening cover A.
Cover B *1
Open Cover B (For DocuPrint 255/305,
raise the lever as shown below to open
cover (1)). After opening cover B, hold
the part marked with  and open the
cover of the fuser unit (2) and remove
any jammed paper.
When a message to remove the
drum/toner cartridge is displayed:
P. 102
[1] (Paper transport section of the
bypass tray), trays
Pull out the tray and follow
the procedure to remove
paper:
P. 102
CAUTION
• The fuser unit is hot. You may
get burnt if you touch it directly.
Cover C *1 (Duplex unit)
Push up the lever shown
in the diagram to open the
cover.
*1: Remove the rear tray (optional)
when opening the back cover.
5.1 When Paper Jams
101
Inside Cover A
Follow the procedure below to remove any jammed paper when the control panel displays
either of the following messages: “Paper jam Open Cover A” or “Remove cartridge Clear
jam”
1.
Open cover A, and holding the drum/toner cartridge by the grip, remove it from the
printer (1).
2.
Turn the roll as shown in the diagram and
remove any jammed paper inside (2).
3.
Return the drum/toner cartridge and cover A to their original positions.
Important
• When the offset catch tray (optional) is installed, close cover A first before returning the tray to its original
position.
• If you continue to print with the offset catch tray folded, this may cause a paper jam. Always use the
printer with the tray open.
Inside Paper Transport Section of the Bypass Tray or Inside the Trays
Follow the procedure below to remove any jammed paper when the following messages are
displayed intermittently: “Remove [1] & all trays. Clear jam” and “Clear jam and close Cover
A”, or “Pull out all trays Clear jam” and “Clear Jam and close Cover A”.
Pulling out [1]
102
1.
When the bypass tray (optional) is installed,
close the bypass tray and pull out the paper
transport section at the bottom.
2.
Open the top of the paper transport section
(1) and remove any jammed paper (2).
5 Troubleshooting
Pulling out paper trays
1.
Pull out all paper trays and remove any
wrinkled paper.
2.
Examine the inside of the printer and
remove any jammed paper.
Note
• When two levels of the optional tray have been
installed and an A5 size (length 148.5 mm) paper is
jammed at the rear of the tray module, hold both
edges of the paper with your hands and pull it out.
After removing the paper
1.
Push the paper transport section and paper
trays completely back into the printer.
2.
Open and close cover A. Doing this will
clear the error message.
5.1 When Paper Jams
103
5.2
When Problems Occur
Before treating the problem as a machine breakdown, refer to the following table and check
the printer condition again.
WARNING
• Never open or remove machine covers that are secured with screws unless specifically
instructed in the user guide. A high voltage component can cause electric shock.
• Do not try to alter the machine configuration, or modify any parts. An unauthorized
modification can cause smoke or fire.
Note
• Information when printing has not been successfully performed is saved in [Job History Report]. If the
job has not been printed, print the [Job History Report] and check the processing status of the job.
Printing data that has not been successfully processed in sometimes discarded. Refer to “6.2 Printing
Reports/Lists” (P. 127) on how to print the [Job History Report].
• Probable causes of trouble are that the printer, computer you are using, server or other hardware is not
correctly set for the network environment you are using, or a printer restriction has been exceeded.
Refer to “Appendix A.6 Precautions and Limitations” (P. 154) and the Network Print Environment User
Guide.
Symptom
No power.
Reason/Action
Is the power to the printer switched off? Press the power switch to the < > position to
switch on the power.
Refer to
• “1.2 Switching On and Off the Power” (P. 17)
Is the power cord disconnected or not securely connected? Switch off the power to the
printer and connect the power cord to the power outlet again. Then, switch on the
power to the printer.
Refer to
• Setup and Quick Reference Guide Connecting the Power Cord to Switch on the
Printer
Is the power cord connected to a power outlet with the correct voltage? Connect the
printer exclusively to a power outlet with a suitable voltage and current rating.
Refer to
• Setup and Quick Reference Guide Safety Notes
104
5 Troubleshooting
Symptom
Cannot print.
Reason/Action
Is the light of the <Ready> indicator off? If so, this printer is offline or in the menu setting
mode. Fix the problem according to the following display status:
• “Off-line”
Press the <Online> button to exit the offline mode.
• Others
Press the <Menu> button to exit the menu setting mode.
Refer to
• “1.1 Main Components and Their Functions” (P. 12)
Is there a message displayed on the control panel? Follow the message to rectify the
problem.
Refer to
• “5.4 Message List” (P. 111)
When a parallel cable is used for connection, are you using a computer that supports
bi-directional communication? By default, the bi-directional communication setting of
the printer is set to [Enable]. If the computer is not responding to bi-directional
communication, printing cannot be performed. In this case, turn the bi-directional
communication setting to [Disable] on the control panel and then print again.
Refer to
• “Parallel” (P. 76)
Is the memory sufficient? Use one of the following methods to rectify the problem.
• When [High Resolution] is selected for [Print Mode] in the [Graphics] tab, set it to
[Standard].
• Select [On] for [Page Print Mode] in the [Detailed Settings] tab.
• Increase the print page buffer.
• Install the additional memory (optional) to increase the memory.
Refer to
• [Print Mode] / [Page Print Mode]: Online Help for the printer driver
• Print page buffer: “Allocate Memory” (P. 92)
Print job sent but the light of
the <Ready> indicator is not
blinking or on.
Is the interface cable disconnected? Switch off the power and check the connection of
the interface cable.
Is the interface configured? Check the port status of the interface.
Refer to
• “Network/Port” (P. 76)
Is the computer environment correctly set up? Check the computer environment, such
as the printer driver.
Light of <Error> indicator is on.
Is there an error message displayed on the control panel? Check the displayed
message and rectify the error.
Refer to
• “5.4 Message List” (P. 111)
Light of <Error> indicator is
blinking.
An error that you cannot rectify by yourself has occurred. Record the displayed error
message or error code, switch off the power, pull out the power plug from the outlet, and
then contact our Customer Support Center or your dealers.
Although no print job is sent,
the message “Printing...” is
displayed on the control panel
(when using the parallel
interface).
Did you switch on the power of the computer after switching on the power to the printer?
Pressing the <Cancel Job> button cancels printing.
Note
• Make sure that you switch on the computer when switching on the power to the
printer.
5.2 When Problems Occur
105
Symptom
Poor print quality.
Reason/Action
Image trouble has probably occurred. Refer to the section after this, “When the Print
Quality Is Poor” to rectify the problem.
Refer to
• “5.3 When the Print Quality Is Poor” (P. 108)
The correct characters are not
printed (printing garbage).
This printer is printing with non-standard built-in fonts. Check the fonts used in the
application. Download the necessary fonts when using PostScript (optional).
The printout is different from
what is displayed on the
screen.
Did you change the TrueType font settings to printer fonts? Change to TrueType font
printing for [Specify Font] on the [Detailed Settings] tab of the printer driver.
Refer to
• Online Help for the printer driver
The light of the <Ready>
indicator is on and blinking but
there is no print output.
There are jobs remaining in the printer. Cancel printing or force the remaining data to be
printed.
To forcibly print the job, press the <Online> button to set the printer in offline mode, then
press the <Eject/Set> button. After the job has been printed, press the <Online> button
again to return the printer to the online mode.
Note
• When a parallel/USB port is used, data may be transmitted in the middle of a job
depending on when the <Online> button is pressed. In this case, subsequent print
data received after the <Eject/Set> button is pressed, will be recognized as a new
job. The data will be printed after the offline mode has been canceled. Furthermore, it
may not be printed properly.
Refer to
• Canceling printing: “1.4 Canceling/Checking Printing” (P. 18)
Printing is taking up a lot of
time.
The receive buffer is insufficient. When printing documents of high resolution, reduce
the memory capacity of items not in use from [Allocate Memory] on the control panel to
increase the print page buffer.
Increasing the receive buffer will speed up the printing. Adjust the buffer size according
to the volume of data to be printed.
You are also recommended to disable ports not in use, and channel the memory to
other purposes.
Refer to
• “Allocate Memory” (P. 92)
Is [High Resolution] selected for [Print Mode]? Change the [Print Mode] setting in the
[Graphics] tab to [Standard] to shorten the printing time.
Refer to
• Online Help for the printer driver
Printing with TrueType fonts may take up printing time. Change the printing method for
TrueType fonts in [Specify Font] on the [Detailed Settings] tab of the printer driver.
Refer to
• Online Help for the printer driver
Top section of printed
document is missing.
Text is reduced.
Are the paper tray guides in the correct positions?
Set the length guide and the right width guide to the correct positions.
Refer to
• “Loading Paper in a Paper Tray” (P. 59)
106
5 Troubleshooting
Symptom
Paper cannot be fed.
Paper jam.
Multiple papers are fed.
Papers are fed at an angle.
Paper is wrinkled.
Reason/Action
Is the paper correctly loaded? Load the paper correctly. For labels, transparencies,
postcards, or envelopes, fan them well first to allow air to enter between each sheet
before loading.
Refer to
• “3.2 Loading Paper” (P. 59)
Is the paper damp? Replace with paper from a new ream.
Refer to
• “3.2 Loading Paper” (P. 59)
Is the correct type of paper used? Load the correct type of paper.
Refer to
• “Usable Paper” (P. 55)
Is the paper tray set correctly? Push the paper tray completely into the printer.
Is the printer placed on a flat location? Place the printer on a stable surface.
Refer to
• Setup and Quick Reference Guide Safety Notes
Are the paper tray guides set in the correct positions? Set the length guide and right
width guide to the correct positions.
Refer to
• “Loading Paper in a Paper Tray” (P. 59)
Have you used any picture postcards? Clean the feed roll.
Refer to
• “Cleaning the Feed Roll” (P. 141)
Papers are fed at more than 1 sheet. Multiple feeding of papers may occur before the
sheets of paper loaded in the tray are used up. Fan the paper to be loaded and load
again. Replenish paper only when all the sheets of the loaded paper are used up.
Envelope is wrinkled.
Envelopes can get wrinkled depending on the type used. Open cover B of this printer
and lift up the levers at both ends of the fuser unit. The wrinkles can be reduced.
After printing the envelope, remember to return the levers to their original positions.
Strange noise.
Is the printer placed on a flat location? Place the printer on a stable surface.
Refer to
• Setup and Quick Reference Guide Safety Notes
Is cover A open? Close cover A securely.
Is the paper tray set correctly? Push the paper tray completely into the printer.
Are there foreign objects inside the printer? Switch off the power and remove any
foreign objects inside the printer. If the object cannot be removed unless the printer is
disassembled, contact our Customer Support Center or your dealers.
5.2 When Problems Occur
107
5.3
When the Print Quality Is Poor
When the print quality is poor, select the closest symptom from the following table to rectify
the problem.
If the print quality does not improve after carrying out the appropriate action, contact our
Customer Support Center or your dealers.
Symptom
Printing is light (faded,
blurred).
Reason/Action
The paper is damp. Replace with paper from a new ream.
Refer to
• “3.2 Loading Paper” (P. 59)
The drum/toner cartridge is defective/damaged or there is no more toner inside the
cartridge. Replace with a new drum/toner cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
The Draft Mode feature is on. Uncheck the [Draft Mode] checkbox on the [Detailed
Settings] tab of the printer driver.
Refer to
• Online Help for the printer driver
Levers on both sides of the fuser unit are raised. Open cover B of this printer and push
down the levers at both ends of the fuser unit.
Black spots or streaks are
printed.
The drum/toner cartridge is defective or damaged. Replace with a new drum/toner
cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
Dirt appears at equal intervals.
The feed route of the paper is stained. Print a few pages to remove the stains.
The drum/toner cartridge is defective or damaged. Replace with a new drum/toner
cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
White dots appear in black
filled areas.
The paper used is not suitable. Load the correct type of paper.
Refer to
• “Usable Paper” (P. 55)
The drum/toner cartridge is defective or damaged. Replace with a new drum/toner
cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
108
5 Troubleshooting
Symptom
Printed image smudges when
rubbed with your finger.
The toner is not fixed on the
paper.
Paper is smeared with toner.
Reason/Action
The paper loaded in the paper tray does not match the paper type set on the control
panel. Set the appropriate paper type of the paper loaded in the paper tray on the
control panel.
Refer to
• “Usable Paper” (P. 55)
• “3.4 Setting Paper Types” (P. 64)
The paper is damp. Replace with paper from a new ream.
Refer to
• “3.2 Loading Paper” (P. 59)
The paper used is not suitable. Load the correct type of paper.
Refer to
• “Usable Paper” (P. 55)
The whole piece of paper is
printed black.
The drum/toner cartridge is defective or damaged. Replace with a new drum/toner
cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
This may be due to breakdown of high voltage power. Contact our Customer Support
Center or your dealers.
Nothing is printed.
Multiple sheets of paper are fed simultaneously. Fan the paper well and reload the
paper.
Refer to
• “3.2 Loading Paper” (P. 59)
The drum/toner cartridge is defective/damaged or there is no more toner inside the
cartridge. Replace with a new drum/toner cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
Spots of missing text
This may be due to breakdown of high voltage power. Contact our Customer Support
Center or your dealers.
The paper is damp. Replace with paper from a new ream.
Refer to
• “3.2 Loading Paper” (P. 59)
The paper used is not suitable. Load the correct type of paper.
Refer to
• “Usable Paper” (P. 55)
Text is blurred.
The paper used is not suitable. Load the correct type of paper.
Refer to
• “Usable Paper” (P. 55)
The paper is damp. Replace with paper from a new ream.
Refer to
• “3.2 Loading Paper” (P. 59)
Missing characters throughout
the length of the paper
The drum/toner cartridge is defective/damaged or there is no more toner inside the
cartridge. Replace with a new drum/toner cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
5.3 When the Print Quality Is Poor
109
Symptom
Text or images are printed at
an angle.
Reason/Action
The paper tray guides are not set in the correct positions. Set the length guide and the
right width guide in the correct positions.
Refer to
• “Loading Paper in a Paper Tray” (P. 59)
Transparencies and envelopes
are not printed clearly.
The type of transparency or envelope loaded cannot be used in this printer. Load the
correct type of paper.
Refer to
• “Usable Paper” (P. 55)
Check that the paper type on the printer driver or the control panel is correctly set.
Refer to
• “3.4 Setting Paper Types” (P. 64)
The Draft Mode feature is turned on and the resolution is set at a low level on the printer
driver. Change the settings on the [Detailed Settings] or [Graphics] tab of the printer
driver.
110
5 Troubleshooting
5.4
Message List
Message List (Alphabetical Order)
This section describes the messages displayed on the control panel. If the displayed error
code is in the format of “xxx-xxx”, refer to “List of Error Codes” (P. 115).
Message
Condition/Reason/Action
xxxx
Printing... Tray *
This indicates that the report/list is being printed.
xxxx.xxxx
Printing... Tray *
This indicates that the secure print job is being printed. The printer is ready to receive
print data from computers.
Add paper-Bypass
xxxx
XXXX
There is no paper left in the bypass tray. Load the paper whose size and orientation
is “xxxx” and whose paper type is “XXXX”.
Note
• When printing reports/lists, print data from computers cannot be received.
Refer to
• “Loading Paper in the Bypass Tray (Optional)” (P. 61)
Add Paper Tray *
xxxx
XXXX
There is no paper whose size and orientation is “xxxx” and whose paper type is
“XXXX” left in the tray.
Load paper whose size and orientation is “xxxx” and whose paper type is “XXXX”
into the tray *.
Refer to
• “Loading Paper in a Paper Tray” (P. 59)
All data
Canceling...
The printer is discarding the remaining print data.
The printer cannot receive any print data from the computer during processing.
All data.
Ejecting... Tray *
The printer is outputting print data. The printer can receive print data from a
computer during processing.
Canceling...
xxxx
Tray *
Discarding the data being printed. The printer can receive print data from a computer
during processing.
Check Bypass
xxxx
XXXX
Inappropriate paper is loaded in the bypass tray.
Load paper whose size and orientation is “xxxx” and whose paper type is “XXXX”
into the bypass tray.
Check Tray *
Inappropriate paper is loaded in tray *.
Load paper whose size and orientation is “xxxx” and whose paper type is “XXXX”
into tray *.
xxxx
XXXX
Refer to
• “Loading Paper in a Paper Tray” (P. 59)
Close Cover *
Cover * is open.
Close Cover *.
Refer to
• “1.1 Main Components and Their Functions” (P. 12)
5.4 Message List
111
Message
Corrupt HD file
Press Set key
Condition/Reason/Action
When the hard disk (optional) is installed, the printer assumes that data in the hard
disk is corrupted if power is cut off when the printer is in use.
Press the <Eject/Set> button on the control panel. The hard disk will be initialized.
Important
• Initializing the hard disk will delete data for registered forms, logos and secure
print. If the PostScript software kit (optional) is installed, PostScript download fonts
will also be deleted.
Corrupt Log file
Press Set key
When the hard disk (optional) is installed, the printer assumes that data in the hard
disk is corrupted if power is cut off when the printer is in use.
Press the <Eject/Set> button on the control panel. The log file will be initialized.
Important
• It takes several tens of seconds to initialize the log file. Do not switch off the power
of this printer when initialization is in progress.
Ejecting...
xxxx Tray *
The printer is forcedly outputting the remaining print data. The printer cannot receive
any print data from the computer during processing.
Empty Center
Output Tray
The center output tray is full. Remove paper from the center output tray.
Ended with Error
xxx-xxx
An error has occurred and printing does not finish successfully.
Check the error code “xxx-xxx” displayed in the screen and perform the appropriate
procedures.
Refer to
• “List of Error Codes” (P. 115)
Incorrect paper
type Reselect
Paper of the type specified under [Specify Paper Type] in the printer driver is not
loaded in the trays. Press the <Eject/Set> button on the control panel to print on
paper of another type or press the <Cancel Job> button to cancel the job.
Set to Print
Stop to Cancel
Initializing
PostScript
This is displayed when the PostScript software kit (optional) is installed and indicates
that the printer system is being initialized. This is displayed when the power is
switched on or the system is reset.
Load Tray *
xxxx
XXXX
There is no paper whose size and orientation is “xxxx” and whose paper type is
“XXXX” left in the tray.
Load paper whose size and orientation is “xxxx” and whose paper type is “XXXX”
into the tray *.
Refer to
• “Loading Paper in a Paper Tray” (P. 59)
Lower Rear
OutputTray lever
Since the rear tray is specified as the output destination, the printer cannot output to
the center output tray. Push down the rear output tray lever and change the output
destination to the center output tray.
Off-line
The printer is offline as the <Online> button has been pressed. To cancel the offline
status, press the <Online> button again.
Off-line
Data in memory
Open Cover A or B
Clear Jam
Note
• The printer cannot receive any print data from the computer while it is offline.
Paper jam has occurred around the printer fuser unit.
Open cover A or B of the printer to remove the jammed paper.
Refer to
• “5.1 When Paper Jams” (P. 101)
112
5 Troubleshooting
Message
Open Cover C and
remove paper
Condition/Reason/Action
Paper jam has occurred around the printer duplex unit. Open cover C of the printer to
remove the jammed paper.
Refer to
• “5.1 When Paper Jams” (P. 101)
Open Cover D and
remove paper
Paper jam has occurred in the offset catch tray of the printer. Open cover D of the
printer to remove the jammed paper.
Refer to
• “5.1 When Paper Jams” (P. 101)
Open Cover A, C
then B Clear jam
Paper jam has occurred around the printer fuser unit.
Open covers A, C, and B in sequence to remove the jammed paper.
Refer to
• “5.1 When Paper Jams” (P. 101)
Paper jam
Open Cover A
Paper jam has occurred around the drum/toner cartridge.
When cover A is opened, the message “Remove cartridge Clear jam” will be
displayed. Follow the instruction to fix the error.
Refer to
• “5.1 When Paper Jams” (P. 101)
Please reboot
Printer
xxx-xxx
Error has occurred.
Switch off the power. After the control panel display is turned off, switch on the power
again. If the same message appears again, take notes on the code “xxx-xxx”. And
then switch off the power. After the control panel display is turned off, pull out the
power plug from the outlet and contact our Customer Support Center or your dealers.
Please wait...
Diagnosing/initializing the printer system. This is displayed when the power is
switched on or the system is reset. After a while, the message “Ready to print” is
displayed.
This also indicates that the printer is warming up to forcedly output the print data
remaining in the printer.
The printer cannot receive any print data from the computer during processing.
Please wait...
xxxx
The printer is warming up to forcedly output the print data remaining in it. The printer
can receive print data from a computer during processing.
Printing...
xxxx
The printer is processing the print data. The printer can receive print data from a
computer during processing.
Printing...
xxxx
Tray *
The printer is outputting data on paper from tray *. Do not pull out the tray being
Pull out all
trays Clear jam
Paper jam has occurred at the rear of the paper trays.
Pull out all the trays to remove jammed paper. And then, open and close cover A.
This will cancel the error.
Clear jam and
close Cover A
used. The printer can receive print data from a computer during processing.
Refer to
• “Inside Paper Transport Section of the Bypass Tray or Inside the Trays” (P. 102)
Push in Bypass
Tray 1 Transport
The paper transport of the bypass tray is pulled out. Install the paper transport
correctly.
Push in Tray *
Tray * is pulled out.
Push tray * completely into the printer.
Raise Rear
OutputTray lever
Since the center output tray is specified as the output destination, the printer cannot
output to the rear tray. Pull up the rear output tray lever and change the output
destination to the rear tray.
Ready to print
The printer is ready to receive print data from computers.
5.4 Message List
113
Message
Ready to print
xxx-xxx
Condition/Reason/Action
An error has occurred in the printer.
Switch off the power. After the control panel display is turned off, switch on the power
again. If the error code appears again, check the error code “xxx-xxx” displayed and
perform the appropriate procedures.
Refer to
• “List of Error Codes” (P. 115)
Ready to print
DNS Update Fail
Unable to retrieve IP address from DNS.
Check the settings for DNS and retrieving the IP address.
Refer to
• Online Help for CentreWare Internet Services
Ready to print
Dupl. IP Address
The IP addresses are duplicated.
Change the IP addresses.
Refer to
• Setup and Quick Reference Guide Setting IP Address
Ready to print
Dupl. SMB Host
There are SMB hosts with the same name.
Change the host names.
Refer to
• Network Print Environment User Guide
Ready to print
Get IP Add. Fail
Failed to retrieve IP address from DHCP server.
Change the retrieval method for the IP address and manually specify the IP address.
Refer to
• Setup and Quick Reference Guide Setting IP Address
Ready to print
Repl. Drum/Toner
The drum/toner cartridge needs to be replaced. Prepare a new drum/toner cartridge.
You can still print about another 100 pages even when this message is displayed.
Ready to print
Replace
010-420
It is about time to replace parts.
Contact and inform our Customer Support Center or your dealers of the error code
“010-420”.
Remove cartridge
Clear jam
Paper jam has occurred at the bottom of the drum/toner cartridge. Remove the drum/
toner cartridge and remove the jammed paper.
Refer to
• “Inside Cover A” (P. 102)
Remove paper from
OffsetCatchTray
The offset catch tray is full. Remove paper from the offset catch tray.
Replace Drum/
Toner Cartridge
There is no toner left in the drum/toner cartridge.
Replace with a new drum/toner cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
Remove [1] & all
trays. Clear jam
Clear jam and
close Cover A
114
5 Troubleshooting
Paper jam has occurred in the bypass tray transport of this printer or at the rear of a
tray. Pull out the transports and all the trays to remove jammed paper. And then,
open and close cover A. This will cancel the error.
Refer to
• “Inside Paper Transport Section of the Bypass Tray or Inside the Trays” (P. 102)
Message
Condition/Reason/Action
SeeBypassSetKey
xxxx
XXXX
[On] is selected for [Bypass-Wait User] on the control panel for printing HP-GL or
HP-GL/2 data.
Load the paper whose size and orientation is “xxxx” and whose paper type is “XXXX”
into the bypass tray, or check that such paper is loaded in the tray. Press the <Eject/
Set> button on the control panel to start printing.
Refer to
• “3.2 Loading Paper” (P. 59)
Set Drum/Toner
Cartridge
The drum/toner cartridge is not installed.
Install the drum/toner cartridge.
Refer to
• “6.1 Replacing the Drum/Toner Cartridge” (P. 124)
Storing image...
xxxx
HDD
The printer is storing the secure/delayed print jobs. The printer can receive print data
from a computer during processing.
Waiting for data
xxxx
The printer is waiting for data to come. The printer can receive print data from a
computer during processing.
List of Error Codes
When an error code is displayed on the control panel or under the [Job Status] column of
the [Job History Report], refer to the following table to fix the error.
Important
• When an error code is displayed, print data remaining in this printer or information saved in its memory
may not be secure.
• Once the power to the printer is switched off, print data remaining in the printer or information saved in
its memory will be deleted.
• When “Please reboot printer xxx-xxx” is displayed, an error that cannot be easily fixed has occurred.
Contact our Customer Support Center or your dealers.
Error code
Reason/Action
003-747
Wrong combination of print parameters, like selecting to print on custom size paper and setting
[Auto] for [Paper Source] on the printer driver and [Auto] for [Paper Size] in trays 1 to 4 on the
control panel.
Check the print parameters.
010-420
Time to replace parts.
Contact and inform our Customer Support Center or your dealers of the error code “010-420”.
016-500
SMTP server name is not specified correctly.
Check whether the settings for SMTP server are correct under [Properties] of CentreWare
Internet Services. Also check the settings for DNS server.
Refer to
• “Environment Settings for E-mail Printing” (P. 50)
016-501
POP3 server name is not set correctly.
Check whether the settings for POP3 server are correct under [Properties] of CentreWare Internet
Services. Also check the settings for DNS server.
Refer to
• “Environment Settings for E-mail Printing” (P. 50)
016-502
Failed to login to POP3 server.
Check whether the POP3 user name and password are correct under [Properties] of CentreWare
Internet Services.
Refer to
• “Environment Settings for E-mail Printing” (P. 50)
5.4 Message List
115
Error code
Reason/Action
016-503
SMTP server name is not set correctly.
Check whether the settings for SMTP server are correct under [Properties] of CentreWare Internet
Services. Also check the settings for DNS server.
Refer to
• “Environment Settings for E-mail Printing” (P. 50)
016-504
POP3 server name is not set correctly at [POP before SMTP] for sending e-mails.
Check whether the settings for POP3 server are correct under [Properties] of CentreWare Internet
Services. Also check the settings for DNS server.
Refer to
• “Environment Settings for E-mail Printing” (P. 50)
016-505
Failed to login to POP3 server at [POP before SMTP] for sending e-mails.
Check whether the POP3 user name and password are correct under [Properties] of CentreWare
Internet Services.
Refer to
• “Environment Settings for E-mail Printing” (P. 50)
016-701
PCL XL print data cannot be processed due to insufficient memory.
When [High Resolution] is selected for [Print Mode] in the [Graphics] tab, set it to [Standard] and
print again.
Refer to
• Online Help for the printer driver
016-702
PCL XL or PostScript print data cannot be processed due to insufficient print page buffer.
Use one of the following methods to fix the error:
• When [High Resolution] is selected for [Print Mode], set it to [Standard].
• Select [On] for [Page Print Mode] in the [Detailed Settings] tab (for PCL XL only).
• Increase the print page buffer.
• Install the additional memory (optional) to increase the memory.
Refer to
• [Print Mode] / [Page Print Mode]: Online Help for the printer driver
• Print page buffer: “Allocate Memory” (P. 92)
016-705
Cannot save Secure Print documents as the hard disk (optional) has not been installed.
The hard disk has to be installed in order to use the secure print feature.
016-706
The number of users of Secure Print/Sample Print has exceeded the limit.
Cancel some of the unnecessary documents or secure print user data stored in the printer, and
print again.
Refer to
• Online Help for the printer driver
116
016-707
Cannot print Sample Print jobs as the hard disk (optional) has not been installed or there is a hard
disk error.
The hard disk has to be installed in order to use the sample print feature.
016-716
TIFF file cannot be spooled due to insufficient disk memory.
Either install the hard disk (optional) or increase the free space by deleting unnecessary data in
the hard disk.
016-720
PCL command syntax error in print processing.
Delete the print job, and print again.
5 Troubleshooting
Error code
Reason/Action
016-721
Error in print processing. This may be due to the following reasons.
• When [Paper Priority] of [Printer Settings] in the common menu has been set to [Not Selected]
for all paper, a job is sent to print using auto paper supply.
To print a job using auto paper supply, configure priority settings for any paper. When custom
paper is selected, [Paper Priority] settings will be automatically changed to [Not Selected].
Refer to
• Setting of paper priority: “Printer Settings” (P. 89)
016-726
Printer language cannot be selected automatically although [Print Mode] has been set to [Auto] on
the control panel.
Select the printer language using the control panel or command.
016-728
Unsupported Tags are found in the TIFF files.
Check the print data.
016-729
Cannot print as color count and resolution of the TIFF data exceed the valid range.
Change the color count and resolution of TIFF files and print again.
016-730
Detected unsupported commands.
Check print data, delete the error-causing commands, and print again.
016-731
Cannot print as the TIFF data has been cut.
Print again.
016-732
The specified form is not registered.
Register the form, and print again.
016-744
Cannot print PDF file as it contains features that are not supported in this printer.
Open PDF file using Adobe Acrobat Reader and select [Print] from the [File] menu to print.
016-748
Cannot print due to insufficient hard disk space.
Reduce the number of print pages such as splitting the print data or printing one copy at a time for
multiple copies.
Also, increase the free space by deleting unnecessary data in the hard disk (optional).
016-749
PJL command syntax error detected.
Check the print settings or correct the PJL command.
016-751
Cannot print as the PDF file is using ContentsBridge.
Open PDF file using Adobe Acrobat Reader and select [Print] from the [File] menu to print.
016-752
Cannot print PDF file by using the PDF Bridge feature due to insufficient memory.
When using the ContentsBridge Utility, change the [Print Mode] settings in the [ContentsBridge]
dialog box to the following:
• When [High Quality] is selected, change to [Standard].
• When [Standard] is selected, change to [High Speed].
Note
• Refer to “Using ContentsBridge Utility to Print PDF” (P. 41).
• When the PDF files are being printed directly without using the ContentsBridge Utility, change
the [PDF] setting on the control panel referring “PDF” (P. 71).
016-753
Password for the PDF file is different from the one set in the printer or in the ContentsBridge
Utility.
Set the correct password in the printer or in the ContentsBridge Utility, and print again.
Note
• Refer to “Using ContentsBridge Utility to Print PDF” (P. 41) about the ContentsBridge Uttility.
• When the PDF files are being printed directly without using the ContentsBridge Utility, change
the [PDF] setting on the control panel referring “PDF” (P. 71).
016-754
PDF file contains objects that are using LZW compression.
Print the file by the following methods:
• Open the PDF file using Adobe Acrobat Reader and select [Print] from the [File] menu to print.
• Use PostScript features to print.
5.4 Message List
117
Error code
016-755
Reason/Action
Cannot print PDF file that does not have print permission.
Use Adobe Acrobat to cancel print prohibit settings in the PDF file, and print again.
Refer to
• Adobe Acrobat related manuals
016-761
Error in image processing.
When [High Resolution] is selected for [Print Mode] in the [Graphics] tab, change it to [Standard]
and print again. If this fails, select [On] for [Page Print Mode] on the [Detailed Settings], and print
again.
Refer to
• [Print Mode] / [Page Print Mode]: Online Help for the printer driver
016-762
Uninstalled printer language selected.
This printer can process HP-GL, HP-GL/2, TIFF and PDF data. Install the PostScript software kit
(optional) to send PostScript data.
016-796
E-mails without attachments are deleted when selections to print only the attachments of received
e-mails are specified.
To print both the e-mail and the mail header, change the settings in [Properties] of CentreWare
Internet Services.
Refer to
• Online Help for CentreWare Internet Services
016-797
E-mail sent to this printer using E-mail Print feature has a wrong address.
Specify the correct address and send again.
Refer to
• “2.10 Printing via E-mail - E-mail Printing” (P. 50)
118
016-799
Wrong combination of print parameters, like selecting to print on custom size paper and setting
[Auto] for [Paper Source] on the printer driver and [Auto] for [Paper Size] in trays 1 to 4 on the
control panel.
Check the print parameters.
116-701
Cannot perform 2 sided printing due to insufficient memory.
You are recommended to increase the memory.
116-702
The job was printed using substitute fonts.
Check the print data.
116-703
Error in PostScript (optional).
Check the print data or uncheck the bi-directional communication check box of the printer driver.
116-710
Received data has exceeded the spool size of HP-GL and HP-GL/2. The printer may not be able
to determine the original size accurately.
Increase the auto layout memory allocation for HP-GL and HP-GL/2 or install the hard disk
(optional).
116-714
Command error in HP-GL and HP-GL/2.
Check the print data.
116-720
Cannot print due to insufficient PCL memory.
Disable unnecessary ports or adjust the buffer size for each memory.
You are also recommended to increase the memory.
116-740
Numeric data error has occurred as a number exceeding the printer limit value has been used in
the print data.
Check the print data.
116-746
The specified form is not registered.
Use a registered form or register the current form.
116-747
The paper margin value is too large for the HP-GL and HP-GL/2 valid coordinates area.
Reduce the paper margin value and print again.
5 Troubleshooting
Error code
Reason/Action
116-748
No drawing data in HP-GL and HP-GL/2 print data.
Check the print data.
116-750
Cannot print banner sheet due to failure in banner sheet feeding tray.
Restore the banner sheet feeding tray to its normal status. Or, change the banner sheet feeding
tray at the control panel.
Refer to
• “System Settings” (P. 86)
116-780
E-mail attachment error in received e-mails.
Check the attachment.
Refer to
• “2.10 Printing via E-mail - E-mail Printing” (P. 50)
5.4 Message List
119
5.5
Network Related Troubles
Using TCP/IP
This section describes how to identify the cause and fix an error when a problem occurs in
the TCP/IP environment. For the troubles that occur in other environments, refer to the
Network Print Environment User Guide.
For Windows 95/Windows 98/Windows Me
„ When the Printer Is Not Printing
This section explains how to fix the printer status when “Unable to print (xxxx Error)”
appears in the window displayed by clicking [Start] > [Settings] > [Printers].
Cause
120
Verification
Action
The printer and the computer
are connected to different
networks.
Check with your network
system administrator to verify
that the network connecting the
computer and that connecting
the printer are linked by a router
or a gateway.
Connect this printer directly to
the network connecting the
computer.
An error has occurred in the
network between the computer
and the printer. Connection
cannot be established.
“Unable to print (NetworkError)”
is displayed.
Ask your network system
administrator to check the
network for errors.
The IP address of the printer is
entered incorrectly.
“Unable to print (NetworkError)”
is displayed. Select [Properties]
from the [File] Menu of the
printer icon and then select
[Port Settings] from the [Details]
tab. Check the IP address
displayed on the [FX TCP/IP
Direct Print Utility Port Setup]
dialog box against the IP
address displayed on [System
Settings List] (for how to print
the [System Settings List], refer
to “6.2 Printing Reports/Lists”
(P. 127)).
Enter the correct printer IP
address in the IP address of the
[FX TCP/IP Direct Print Utility
Port Setup] dialog box.
The printer is switched off after
a print instruction has been sent
from a computer. Or the print
instruction is sent to the printer
which is switched off.
“Unable to print (NetworkError)”
is displayed. Check whether the
printer is switched on.
Switch on the printer.
Print instructions from multiple
computers are sent to the
printer at the same time.
“Unable to print (NetworkError)”
is displayed.
None (Printing will be resumed
automatically).
Printing files cannot be spooled
due to insufficient disk capacity
of the computer.
“Unable to print (SpoolError)” is
displayed. Double-click [My
Computer] and right-click the
disk (example: C drive) installed
with Windows 95, Windows 98,
Windows Me. Select
[Properties] from the menu
displayed and then check the
free space available.
After deleting unnecessary files
to increase the free space
available, select [Pause
Printing] from the [Documents]
menu of the printer window to
enable printing to restart.
5 Troubleshooting
For Windows NT 4.0/Windows 2000/Windows XP/Windows Server 2003
„ When the Printer Is Not Printing
Cause
Verification
Action
Incorrect IP address.
Ask your network administrator
to check that the IP address is
correct.
Specify the correct IP address
for the printer.
The print data sent from a
computer in a single print
instruction exceeded the upper
limit of the receiving capacity
while [Memory] is selected for
[LPD Spool].
Check the memory capacity of
[LPD Spool] and compare it with
the print data which was sent in
the single print instruction.
1.
If a single file of print data
has exceeded the upper
limit of the memory
capacity, divide the file into
smaller ones and try again.
2.
If multiple files have
exceeded the upper limit of
memory capacity, reduce
the number of files to be
sent at one time.
An irrecoverable error has
occurred during printing.
Check if an error is displayed on
the control panel.
Switch off and then on the
printer.
The transport protocol is
different from that of the
computer.
Check the selected transport
protocol.
Select the same transport
protocol as that of the computer.
Using CentreWare Internet Services
Symptom
Cannot be connected to
CentreWare Internet Services.
Reason/Action
Is the printer working correctly?
Check if the power of the printer is switched on.
Is Internet Services enabled?
Print out the [System Settings List] to check.
Is the URL correctly entered?
Check the URL again. If connection fails, enter the IP address to
connect.
Is the proxy server used?
Some proxy servers do not allow this feature.
Try connection without using the proxy server.
Refer to
• Online Help for web browser
The “Please wait” message is
displayed throughout the Web
browser.
Wait for a while as instructed.
If the problem persists, refresh the web browser. If nothing happens,
check if the printer is working properly.
The [Refresh] button is not
working.
Are you using the supported OS and a web browser?
Refer to “6.3 Checking/Managing the Printer Status on a Web
Browser” (P. 130) to check whether the OS and web browser you
are using are supported.
Selecting the left frame menu
does not change the display.
The screen display is distorted.
Change the window size of the web browser.
The latest information is not
displayed.
Click [Refresh].
5.5 Network Related Troubles
121
Symptom
122
Reason/Action
The new settings were not
reflected by clicking the [Apply
New Settings] button.
Is the entered value correct?
If an invalid value is entered, it will be automatically changed to a
value within the range.
Clicking the [Apply New
Settings] button prompts
messages such as “no data” or
“the server has returned invalid
or unrecognizable response”.
Are the user name and password correct?
Enter the correct user name and password.
5 Troubleshooting
Switch off and then on the printer.
5.6
Mail Related Troubles
This section explains how to fix the troubles when the Mail Notice Service and E-mail
Printing features are used.
Symptom
Reason/Action
Cannot perform E-mail Printing.
Check the following settings in [Properties] of CentreWare Internet
Services.
• Is the printer e-mail address specified?
• Is [Enable] specified for [Receive E-mail]?
• Are the SMTP server IP address and POP3 server IP address (if
[POP3] is selected as the receive protocol) specified correctly?
• Are the POP user name and password specified correctly?
Is the permitted domain specified?
Specify your own domain as the permitted domain in [Properties] of
CentreWare Internet Services. You can check the permitted domain
settings in [Domain List]. For details, refer to the Online Help for the
CentreWare Internet Services.
Are the SMTP server and POP server working correctly?
Check with your network administrator.
During E-mail Printing, the
attached PDF file was not
printed.
If the memory capacity is insufficient, it may not be printed. If you
print big attachments frequently, we recommend adding memory.
During mail notification
services, the printer status was
not notified by e-mail.
Check the following settings in [Properties] of CentreWare Internet
Services.
• Is the printer e-mail address specified?
• Is [Enable] specified for [Mail Notice Service]?
• Are the SMTP server IP address and POP3 server IP address (if
[POP3] is selected as the receive protocol) specified correctly?
• Are the POP user name and password specified correctly?
• Are the items to be notified specified correctly?
• Are the destination e-mail addresses entered correctly?
Are the SMTP server and POP server working correctly?
Check with your network administrator.
5.6 Mail Related Troubles
123
6
Daily Care
6.1
Replacing the Drum/Toner Cartridge
The drum/toner cartridge includes the toner and the photosensitive drum. When it is about
time to replace the drum/toner cartridge, the following message appears on the control
panel.
After the message is displayed,
you can continue to print normally for
about 100 sheets.
During this period, prepare a new
drum/toner cartridge.
When this message is displayed, replace the drum/toner
cartridge.
(Printing stops)
Note
• The possible number of pages that can be printed of the drum/toner cartridge is the number of pages
printed continuously at a print ratio of 5% using A4
size paper.
• The possible number of pages that can be printed differs according to factors such as the print contents,
paper size, paper type, environment used, and the frequency that the printer is switched on and off.
• If you continue to print with a drum/toner cartridge whose replacement is long overdue, it may affect the
functions of this printer, such as the print quality. It is recommended to replace with a new drum/toner
cartridge.
• You can specify whether to stop printing when the drum/toner cartridge is due for replacement. For
details, refer to “System Settings” (P. 86).
• Before ordering a new drum/toner cartridge, check the product code listed in “Appendix A.2 Optional
Accessories and Consumables” (P. 148).
Caution on Handling the Drum/Toner Cartridge
When handling the drum/toner cartridge, take note of the following points:
WARNING
• Never throw a drum/toner cartridge into an open flame. It can cause an explosion and
you can get burnt.
• Do not subject it to direct sunlight or strong light.
• When installing the drum/toner cartridge, select a location not subject to strong light and
try to finish the installation within 5 minutes.
• Do not touch the surface of the photosensitive drum. Do not let the drum/toner cartridge
stand or place it upside down. The drum might be damaged.
• A drum shutter protects the photosensitive drum from light. Do not open the drum shutter.
• Although the toner is not harmful to the body, wash it off immediately if your hands or
clothes are stained with it.
• It is recommended to use up the drum/toner cartridge within 1 year after opening it.
124
6 Daily Care
Replacing the Drum/Toner Cartridge
1.
Remove any output paper and open cover
A.
Note
• When the offset catch tray (optional) is installed, fold
the tray first before opening cover A.
Important
• Do not touch any parts inside the printer.
2.
Hold the drum/toner cartridge by the grip
and pull it out slowly.
Note
• To prevent the toner from dirtying the floor, lay a piece
of paper on the floor first before putting the drum/toner
cartridge down.
3.
Take the new drum/toner cartridge out of
the packaging box and shake it 7 to 8 times
as shown in the diagram.
Important
• If the toner is not evenly spread out, the print quality
may be reduced. Also, if you did not shake the drum/
toner cartridge well, there may be operating noise or
the interior of the cartridge may be damaged during
operation.
• Do not touch the surface of the photosensitive drum.
4.
Place the drum/toner cartridge on a flat
surface and pull out the seal horizontally.
Important
• When pulling out the seal, pull it out horizontally. The
tape might break if it is pulled out diagonally.
• After the seal has been pulled out, do not shake or
bump the drum/toner cartridge.
6.1 Replacing the Drum/Toner Cartridge
125
5.
Hold the drum/toner cartridge by the grip
and insert it into the slot inside the printer.
Important
• Do not touch any parts inside the printer.
• Ensure that the drum/toner cartridge is loaded
securely in place.
• After opening cover A, remove any dust or stains
inside the printer with a dry clean cloth.
6.
Close cover A securely.
Important
• If the offset catch tray is folded as in step 1, close cover A and then return the tray to its original position.
• If you continue to print with the offset catch tray folded, this may cause a paper jam. Always use the
printer with the tray open.
126
6 Daily Care
6.2
Printing Reports/Lists
This section explains the types of reports/lists and how to print them.
Types of Reports/Lists
Other than print data from the computer, this printer has the feature to print the following
reports/lists.
Reports
System Settings List
Description
Prints status of the printer such as hardware configuration and
network information. Print this report to check whether optional
accessories have been correctly installed.
Note
• For DocuPrint 255/305, [Rear Output Tray] is printed in the column
for [Output Device] even when the printer is in standard
configuration.
Job History Report
Prints information on printing result, such as whether data from the
computer has been printed correctly. The status of maximum 50 jobs
can be printed on the [Job History Report].
Use the control panel to set whether to print the [Job History Report]
automatically for every 50 jobs completed. For details, refer to “Auto
Job History” (P. 88).
Description of jobs with error are printed in the [Job Status] column.
For details on the error description, refer to “List of Error Codes”
(P. 115).
Error History Report
Prints information of up to the latest 50 errors that occurred in this
printer.
Print Meter Report
Prints information on the total printed pages and total number of
sheets used in this printer according to different computer or job
owners. The [Print Meter Report] counts pages from the point where
data has been initialized.
Fonts List
Prints information on the fonts that can be used.
TIFF Settings List
Prints setting information of TIFF print mode.
TIFF Logical Printers List
Prints a list of logical printers created in TIFF print mode. Allows you
to check the settings for up to 10 registered logical printers.
Note
• Settings for TIFF logical printer are done in the CentreWare
Internet Services. For details, refer to the Online Help for the
CentreWare Internet Services.
PDF Settings List
Prints [PDF] settings of the control panel.
Allows you to print the PDF file directly and check the settings without
using the ContentsBridge Utility.
Note
• [Layout] will not be printed when [PS] has been selected for
[Process Mode] on the control panel.
6.2 Printing Reports/Lists
127
Reports
Description
HP-GL/2® Settings List
Prints setting information of HP-GL/2 emulation mode.
HP-GL/2® Logical Printers/
Stored Jobs List
Prints a list of logical printers created in HP-GL/2 emulation mode.
Allows you to check the settings for up to 10 registered logical
printers.
Note
• Settings for HP-GL/2 logical printer are done in the CentreWare
Internet Services. For details, refer to the Online Help for the
CentreWare Internet Services.
PCL Settings List
Prints setting information of PCL print mode.
PCL Form List
Prints a list of PCL forms.
Domain List
Prints a list of permitted domains that have been configured.
PostScript® Fonts List
Prints a list of PostScript fonts when the PostScript software kit
(optional) has been installed.
PostScript® Logical Printers
List
Prints a list of logical printers created in PostScript when the
PostScript software kit (optional) has been installed. Allows you to
check the settings for up to 10 registered logical printers.
Note
• Settings for PostScript logical printer are done in the CentreWare
Internet Services. For details, refer to the Online Help for the
CentreWare Internet Services.
Stored Documents List
Prints a list of documents stored in the printer when using the secure
print/sample print/delayed print feature. This list can be printed when
the hard disk (optional) has been installed.
Refer to
• “2.5 Print Confidential Document - Secure Print” (P. 32)
• “2.6 Print After Checking Printing Result - Sample Print” (P. 35)
• “2.7 Print at a Specified Time - Delayed Print” (P. 38)
Note
• Print the report or list from the control panel. Refer to “Printing Reports/Lists” (P. 129) for details.
• For details on [HP-GL/2® Settings List] and [HP-GL/2® Logical Printers/Stored Jobs List], refer to the
Emulation Settings Guide found in the CD-ROM that is bundled with this printer.
128
6 Daily Care
Printing Reports/Lists
Print the report/list by operating the control panel.
1.
Press the <Menu> button to display the Menu screen.
2.
Press the < > or < > button until [Report/List] is displayed, then press the < >
button.
3.
Press the < > or < > button until the desired report/list is displayed, then press the
< > button.
Note
• To print the next list, check that [Print Language] is displayed and press the <
or < > button until the desired list is displayed, then press the < > button.
• PostScript® Logical Printers List
• HP-GL/2® Setting List
• HP-GL/2® Logical Printers/Stored Jobs List
• TIFF Settings List
• TIFF Logical Printers List
• PDF Settings List
> button. Press the <
>
• PCL Settings List
4.
Press the <Eject/Set> button.
The selected report/list will be printed.
Note
• Reports/Lists cannot be output to the rear tray (optional). When the rear tray is installed, lower the rear
output tray lever.
5.
Press the <Menu> button when printing has completed.
6.2 Printing Reports/Lists
129
6.3
Checking/Managing the Printer Status on
a Web Browser
When the printer is installed in a TCP/IP environment, you can check printer status and
configure settings using a web browser on a network computer.
This feature is known as CentreWare Internet Services.
You can also check the remaining volume of consumables and paper loaded in this printer
via CentreWare Internet Services.
Click the desired
item to display its
status.
Important
• User name and password may be required to configure certain items in the CentreWare Internet
Services. The default user name and password are “admin” and “x-admin” respectively. You must
change the default password upon use.
Settings for CentreWare Internet Services
This section explains the environment and settings required for using CentreWare Internet
Services.
Note
• CentreWare Internet Services is not available when the printer is used as a local printer.
Computer OSs
• Microsoft® Windows® 95 Operating System (ServicePack 1 or later)
• Microsoft® Windows® 98 Operating System
• Microsoft® Windows® Me Operating System
• Microsoft® WindowsNT® Workstation 4.0 (ServicePack 4 or later)
• Microsoft® WindowsNT® Server 4.0 (ServicePack 4 or later)
• Microsoft® Windows® 2000 Professional
• Microsoft® Windows® 2000 Server
• Microsoft® Windows® XP Professional
• Microsoft® Windows® XP Home Edition
• Mac OS 7.6.1 or later
130
6 Daily Care
Browsers
• Netscape Communicator 4.78, Netscape 7 for Windows
• Internet Explorer ver6.0 SP1 for Windows
• Opera 7 for Windows
• Netscape 7 for Macintosh
• Internet Explorer ver5 (Mac OS 8.x/9.x), 5.2 (Mac OS X), 6.0
• Safari 1.0 (Mac OS X v10.2)
Web Browser Settings for CentreWare Internet Services
You are recommended to bypass the proxy server and specify the printer’s address directly
when using the CentreWare Internet Services.
Note
• Specifying the printer’s address via the proxy server may slow down the response or disable the display
of the screen.
• For details on the settings, refer to the Online Help for your web browser.
For CentreWare Internet Services to work properly, the following settings must be
configured on the web browser.
„ For Netscape Communicator
• Settings that enable JavaScript are selected.
• To compare the document in the cache and the document on the network, either the
setting that compares them every session or the setting that compares them every time
is selected.
„ For Internet Explorer
• Settings that enable active script are selected for the security level.
• For newer versions of stored pages, either the setting that displays it or the setting that
checks it every time Internet Explorer starts is selected.
Setting the Printer
To use CentreWare Internet Services, IP address of this printer must be set and
[InternetServices] activated (default: [Enable]). When [InternetServices] is disabled, set it to
[Enable] on the control panel.
Refer to
• “InternetServices” (P. 85)
6.3 Checking/Managing the Printer Status on a Web Browser
131
Procedure
To use CentreWare Internet Services, follow the procedures below to activate the web
browser.
1.
Activate the computer and web browser.
2.
At the address column of the web browser, enter the IP address or URL of the printer
and then press the <Enter> key.
• Example of an URL entry
• Example of an IP address entry
Note
• When specifying port number, add “:” and “80” (default port number) after the address. The port number
can be changed under [Properties] > [Protocol Settings] > [HTTP] of the CentreWare Internet Services.
When connecting to CentreWare Internet Services from the web browser after changing the port
number, add the port number after “:” in the address.
The CentreWare Internet Services screen appears.
Using Online Help
For details regarding the items that can be set in each screen, click the [Help] button to
display the Online Help.
132
6 Daily Care
IP Filter Feature via IP Address List
This feature allows you to register the IP addresses of computers that can be used in this
printer. This will limit IP address used for receiving print data.
1.
Click [Properties] in CentreWare Internet Services.
2.
Click [Protocol Settings] > [TCP/IP] from the left menu.
3.
Select the [Enable] check box to the right of [IP Filter] and click the [Edit] button.
Note
• Enter the user name and password if requested and click [OK].
4.
Specify the IP address permitted for TCP/IP connection in [Permitted IP Address].
5.
Specify the address mask in [IP Mask] corresponding to the registered IP address in
[Permitted IP Address].
For example, if the [Permitted IP Address] is 129.249.110.23 and the [IP Mask] is
255.255.255.0, the IP address for receiving print data is 129.249.110.* (* is from 1 to
254). This means that IP addresses from 129.249.110.1 to 129.249.110.254 can be
received.
6.
Click [Apply New Settings] to reboot the printer.
6.3 Checking/Managing the Printer Status on a Web Browser
133
6.4
Checking Printer Status via E-mail
When connected to a network environment where sending and receiving of e-mails is
possible, this printer can send an e-mail with the following report to a specified e-mail
address: completed print jobs from the computer, error history, list of rejected print jobs/
e-mails.
This feature is known as Mail Notice Service.
About Mail Notice Service
The types of information that can be sent through Mail Notice Service are listed below.
Types of information
Description
Job Completion
Notifies the status of print jobs (completed, canceled or confirm) from the
computer. (This is only used for the PCL printer driver.)
Regular Notice
Notifies the conditions leading to errors that need to be attended by user.
IP Reject Notice
A mail notice will be sent after the printer receives print requests from users
whose IP addresses are not registered in the Permitted IP Address. The
mail notice will include information about the IP address of the rejected
client, the number of print rejects and the time of the last reject for different
clients.
Domain Reject Notice
A mail notice will be sent after the printer receives e-mails from users whose
domain are not registered in the Permitted Domain. The mail notice will
include information about the e-mail address of the user, the number of mail
rejects and the time of the last reject for different clients.
Notification Registration
Completed
Notifies any changes to the settings of Mail Notice Service (such as
conditions for mail notification or address for notification).
Refer to
• How to specify user limitation: “IP Filter Feature via IP Address List” (P. 133)
• How to specify the Permitted Domain: Online Help for CentreWare Internet Services
Settings for Mail Notice Service
To use the Mail Notice Service, settings on the network and e-mail environment are
required. Check with your network administrator whether these settings are completed.
Network Environment
• Register user account
134
6 Daily Care
Setting the E-mail Environment (at This Printer)
Activate CentreWare Internet Services and set Port Status, Machine E-Mail Address, TCP/
IP environment and mail server.
Configure the following items according to your e-mail environment under [Properties].
Note
• After configuring the settings, always click [Apply New Settings] and switch off/on the printer to reboot.
• Select the [Enable] check box at [Port Status] > [Mail Notice Service] and switch off/on the printer. [Mail
Notice Settings] will be displayed.
*: Factory default
Item
Item to be configured
Description
Machine Details
Administrator E-mail Address
(recommended setting), Machine
E-mail Address
For details, refer to “Machine Details”
(P. 51) of “Environment Settings for E-mail
Printing”.
Port Status
Mail Notice Service
Select the check box.
Protocol
Settings
> TCP/IP
Host Name, Get DNS Address, DNS
Address 1-3, DNS Name
For details, refer to “Protocol Settings >
TCP/IP” (P. 51) of “Environment Settings
for E-mail Printing”.
Protocol
Settings >
E-mail
Receiving Protocol, POP3 Server
Address, POP3 Server Check
Interval, POP User Name, POP User
Password, SMTP Sending
Authentication, SMTP Server
Address
For details, refer to “Protocol Settings >
E-mail” (P. 52) of “Environment Settings for
E-mail Printing”.
Mail Notice
Settings
Mail Notice Settings
Select appropriate settings for mail
notification.
Recipient Mail Address
Up to 128 alphanumeric characters can be
entered for the notification e-mail address,
including the ASCII characters for “@” (at
mark), “.” (full stop), “-” (hyphen) and “_”
(underscore).
Setting Printer Driver Properties (at the Computer)
Configure the following settings in the properties of the PCL printer driver in order to receive
e-mails regarding print job results. This section explains the procedure using Windows XP
as an example.
1.
Click [Start] on the taskbar, then select [Printers and Faxes].
2.
Click the icon of this printer, and then select [Properties] from the [File] menu.
3.
Click [Printer Settings] on the [General] tab.
The [Printer Settings] dialog box appears.
4.
Click the [Detailed Settings] tab.
6.4 Checking Printer Status via E-mail
135
5.
Select the [Notify Job End by E-mail] check box.
5
6
136
6.
Enter the e-mail address for notification in [E-mail Address].
7.
Click [OK].
6 Daily Care
6.5
Checking Printed Pages
This section explains how to check the total number of printed pages.
Checking Total Printed Pages on Meter
The total number of printed pages for different meters can be checked on the display of the
control panel.
The meter is divided according to the color modes.
Meter 1
Black/White printing
Meter 2
Normally not used.
Meter 3
Color printing
Not available on this printer.
The following procedure shows how to check the meter.
1.
Press the <Menu> button to display the Menu screen.
2.
Press the < > or < > button until [Meter Reading] is displayed and then press the
< > button.
3.
Press the < > or < > button until the desired meter is displayed.
4.
After checking, press the <Menu> button.
Checking Total Printed Pages on Print Meter Report
The [Print Meter Report] allows you to check the total printed pages and total number of
sheets used in this printer according to different computer or job owners. The [Print Meter
Report] counts pages from the point where data has been initialized.
Operate the control panel to print the [Print Meter Report].
Print Results From the Print Meter Report
The following items are printed on the [Print Meter Report].
Date of Initialization
The date and time when printer meter data was initialized.
Date/Time
The date and time when the [Print Meter Report] was printed.
The following items are printed for every job owner.
Job Owner Name
Up to 200 owner names are printed. The administrator name is specified by
[Specify Job Owner] on the printer driver. When the job owner is not
specified, or when the 201st print job is received, this job will be counted in
the [UnknownUser] column. Printing of reports/lists will be counted in the
[Report/List] column.
Pages
The total number of printed pages. This is counted for every completed print
job.
Sheets
The total number of sheets for paper used for printing. This is counted for
every completed print job.
Note
• You can initialize the data for [Print Meter Report]. For details on the feature, refer to “Init/Del Data”
(P. 94). For details on the procedure, refer to “Initializing Print Meter Data” (P. 138).
6.5 Checking Printed Pages
137
How to Print the Print Meter Report
1.
Press the <Menu> button to display the Menu screen.
2.
Press the < > or < > button until [Report/List] is displayed, then press the < >
button.
3.
Press the < > or < > button until [Print Meter] is displayed, then press the < >
button.
4.
Press the <Eject/Set> button.
The [Print Meter Report] is printed.
5.
Press the <Menu> button when printing has completed.
Initializing Print Meter Data
138
1.
Press the <Menu> button to display the Menu screen.
2.
Press the < > or < > button until [Admin Menu] is displayed, then press the < >
button.
3.
Press the < > or < > button until [Init/Del Data] is displayed, then press the < >
button.
4.
Press the < > or < > button until [Print Meter] is displayed, then press the < >
button.
5.
Press the <Eject/Set> button.
Initialization will start.
6.
Press the <Menu> button.
6 Daily Care
6.6
Cleaning the Printer
This section describes how to clean the printer in order to maintain it in good condition and
print clean printouts all the time.
CAUTION
• Be sure to switch off and unplug the machine before accessing the interior of the
machine for cleaning, maintenance, or fault clearance. Access to a live machine’s
interior can cause electric shock.
Cleaning the Exterior
Clean the exterior of the printer about once a month. Wipe the parts with a wet but
well-wrung soft cloth. Then wipe with another dry soft cloth. For stubborn stains, moisten a
soft cloth with a small amount of neutral detergent, and gently wipe the stain off.
Important
• Do not spray the detergent directly on the printer. The liquid detergent may enter the printer through a
gap and cause problems. Never use cleaning agents other than water or neutral detergent.
6.6 Cleaning the Printer
139
Cleaning the Interior
After clearing paper jams or replacing the drum/toner cartridge, inspect the inside of the
printer before closing cover A.
CAUTION
• Never touch a labeled area found on or near the heat roller. You can get burnt. If a sheet
of paper is wrapped around the heat roller, do not try to remove it by yourself to avoid
injuries or burns. Doing so can cause injuries or burns. Switch off the machine
immediately, and contact our Customer Support Center or your dealers.
• Remove any remaining pieces of paper.
• Remove any dust or stains with a dry clean cloth.
140
6 Daily Care
Cleaning the Feed Roll
When feeding cannot be done, follow the procedure below to wipe the feed roll gently with
a well-wrung soft cloth.
There are feed rolls in the interior of this printer (two locations, total of four), tray module
(one location), paper tray (one location) and optional bypass tray (one location).
Feed roll
Inside of printer (two locations)
Open cover A and after uninstalling
the drum/toner cartridge, clean the
feed roll.
Tray module (one location)
Even without uninstalling the
tray module, you can clean the
feed roll after pulling out the
paper tray.
Paper tray (one location)
Pull out the paper tray and
clean the feed roll.
Bypass tray (one location)
Switch off the power. Pull out the
bypass tray and clean the feed
roll.
The following procedure explains how to clean the feed roll set in the paper tray. Follow this
procedure also when cleaning the feed rolls inside of the printer and the tray module.
Note
• The feed roll is a regular replacement part.
6.6 Cleaning the Printer
141
1.
Pull the paper tray out of the printer.
2.
While pushing the retard part (see right
diagram) down (1), widen the tab on the
feed roll to loosen it (2) and then slowly
remove the feed roll from the shaft of the
paper tray (3).
3.
Wipe the rubber parts with a wet but
well-wrung soft cloth.
4.
Turn the short tab of the feed roll to the right
and slowly push it onto the shaft of the
paper tray.
By aligning the slot of the feed roll with that
of the shaft, push the feed roll completely in
so that the short tab fits into the slot of the
shaft.
5.
142
6 Daily Care
Push the paper tray completely into the printer.
Short tab
6.7
When Moving the Printer
Carry out the following procedure when moving the printer.
CAUTION
• The machine, without the optional accessories, paper trays, consumables and paper,
weighs 20.0 kg (DocuPrint 205) or 22.0 kg (DocuPrint 255/305). When moving the
equipment, make sure that there are two or more persons carrying it.
• When lifting the machine, be sure to observe the following points. Failure to do so may
cause the machine to fall and result in injuries.
• Two persons, one facing the front of the machine (control panel) and the other facing
the back, should firmly grip the recessed areas on the bottom part of both sides of the
machine. Never try to lift the machine by gripping any other areas.
• Bend your knees to avoid possible injuries to your back.
• Do not tilt the machine more than 10 degrees.
Important
• If the duplex unit (optional) or A3 universal tray (optional) has been installed, uninstall it before moving
the printer. If these are not fixed securely to the printer, they may fall to the ground and cause injuries.
For details on how to uninstall the optional accessories, refer to the each manual that is bundled with
each accessory.
1.
Press the power switch of this printer to the <{> position to switch off the power.
2.
Remove all cords, such as the power cord and interface cables.
3.
Remove any paper in the center output tray and return the extension output tray to its
original position if it’s extended.
4.
Pull out the paper tray from the printer and remove any paper in the tray.
Keep the paper wrapped and away from humidity and dirt.
5.
Push the paper tray completely into the printer.
6.
Open cover A.
Important
• Do not touch any parts inside the printer.
7.
Hold the drum/toner cartridge by the grip and pull it out slowly.
Important
• It is necessary to uninstall the drum/toner cartridge. If you move the printer with the drum/toner cartridge
installed, the toner may spill out inside of the printer.
• Do not shake the drum/toner cartridge after uninstalling it from the printer. The toner will spill.
• Put the uninstalled drum/toner cartridge back into its original aluminum bag or wrap it with a thick cloth to
prevent it from being exposed to strong light.
8.
Close cover A securely.
9.
Lift the printer and move it gently. If the printer is to be moved over a long distance,
pack it inside a box.
6.7 When Moving the Printer
143
A
Appendix
A.1
Specifications
Product Specifications
This Printer
Item
Contents
Machine type
Desktop
Printing system
Laser xerography
Fusion method
Heat roller (oil-less)
Warm-up time
18 seconds or less (when power is switched on, temperature: 20 °C)
Continuous print speed
Paper feed from trays 1 to 4*1
DocuPrint 205:
(A4
, plain)
1 sided print: 20.4 sheets/min*2
2 sided print: 17.8 sheets/min*3, 4
DocuPrint 255:
1 sided print: 25.4 sheets/min*2
2 sided print: 17.8 sheets/min*3, 4
DocuPrint 305:
1 sided print: 30.6 sheets/min*2
2 sided print: 21.4 sheets/min*3, 4
*1 The print speed may decrease due to paper type such as
postcard, transparency or envelope; size, and printing conditions.
*2 Continuous print speed of documents that are all in A4
landscape. The print speed may decrease due to image quality
adjustment.
*3 Continuous print speed of documents in A4 landscape.
*4 When the duplex unit (optional) is installed.
Resolution
Output resolution: 1200 dpi (47.2 dots/mm), 600 dpi (23.6 dots/mm)
Data processing resolution: 1200 dpi (47.2 dots/mm), 600 dpi (23.6
dots/mm)
About 2400 dpi resolution for the Image Enhancement feature
Gradation
144
A Appendix
256 gradations
Item
Paper size
Contents
Tray 1
Standard sizes that can be automatically detected:
A5
, B5
, A4
, A4
, B4
, A3
, Letter (8.5 × 11")
,
Legal (8.5 × 14")
Others:
Custom (76 × 98 - 305 × 900 mm)
Tray 2 - 4
Standard sizes that can be automatically detected:
A5
, B5
, A4
, A4
, B4
, A3
, Letter (8.5 × 11")
,
Legal (8.5 × 14")
Others:
Custom (76 × 148 - 297 × 432 mm)
Bypass tray (optional)
Standard sizes that can be automatically detected:
B5
, A4
, B4
Legal (8.5 × 14")
Others:
A5
, A3
, Letter (8.5 × 11")
,
, Executive (7.25 × 10.5")
, Custom (76 × 98 - 305 × 900 mm)
Duplex unit (optional):
A5
, B5
, A4
Legal (8.5 × 14")
, A4
, B4
, A3
, Letter (8.5 × 11")
,
, Custom (100 × 139 - 305 × 432 mm)
Imageless width: Top/bottom edge 4 mm, Both edges 4 mm
Paper type
Tray 1 - 4:
Plain paper/recycled paper (60 - 90 g/m2), transparencies (for
monochrome printing), heavyweight 1 (90 - 156 g/m2) such as
envelopes, labels, heavyweight 2 (157 - 216 g/m2)
Bypass tray (optional):
Plain paper/recycled paper (60 - 90 g/m2), transparencies (for
monochrome printing), heavyweight 1 (90 - 135 g/m2) such as
envelopes, labels, Japanese official postcards
Duplex unit (optional):
Plain paper/recycled paper (60 - 90 g/m2), heavyweight 1 (90 - 156
g/m2), heavyweight 2 (157 - 190 g/m2)*
* Quality of printing on both sides of Japanese official postcards can
not be guaranteed.
Paper supply
(all paper: A4 size, P paper)
DocuPrint 205:
Standard:
Tray 1 (150 sheets), Tray 2 (250 sheets)
Optional:
A3 universal tray (250 sheets)
A3 universal tray (550 sheets)
Bypass tray (100 sheets)
Up to maximum 1500 sheets when the A3 universal tray (550) is
added to the standard configuration.
DocuPrint 255/305:
Standard:
Tray 1 (150 sheets), Tray 2 (550 sheets)
Optional:
A3 universal tray (250 sheets)
A3 universal tray (550 sheets)
Bypass tray (100 sheets)
Up to maximum 1800 sheets when the A3 universal tray (550) is
added to the standard configuration.
A.1 Specifications
145
Item
Output tray capacity
(all paper: A4 size, P paper)
Contents
DocuPrint 205:
Standard: About 250 sheets (face down)
DocuPrint 255/305:
Standard: About 500 sheets (face down)
Optional:
Rear tray: About 70 sheets (face up)
Offset catch tray: About 500 sheets (face down)
CPU
PPC 603e 266 MHz
Memory capacity
Standard 64 MB, maximum 576 MB, 1 memory slot (1 empty slot)
Hard disk
Optional
Installed Fonts
Standard: 81 PCL fonts (Agfa 80, OCR-B*)
Optional: PostScript European 136 styles
* Can be used on the PostScript software kit (optional).
Page description language
Standard: PCL XL
Optional: PostScript 3
Emulation
Standard:
PCL 5e, HP-GL, HP-GL/2, TIFF, PDF
Optional:
ESC/P, KSSM
Supported OS
Windows 95, Windows 98, Windows Me, Windows NT 4.0,
Windows 2000, Windows XP, Windows Server 2003, Mac OS
Interface
Standard:
Supported protocol
Centro: Compatible, Nibble, ECP
Ethernet (100Base-TX/10Base-T)
Bi-directional parallel (IEEE1284-B), USB (Full Speed),
Serial (25 pin)
Ethernet:
Network protocol
TCP/IP, IPX/SPX, NetBEUI, UDP/IP
Network service
LPD, SMB, NetWare, EtherTalk (when the PostScript software kit
(optional) is installed), SNMP, HTML/HTTP, DHCP, WinsClient,
DNS, IPP, Port9100
Power source
120 V, 11 A, 50/60 Hz
220 - 240 V, 5.5 A, 50/60 Hz
Operating noise
Working: 6.34B (A)
Waiting: 4.5B (A)
Important
• Based on ISO7779
• Unit B(A): acoustic power level
Power consumption
DocuPrint 205/255: Maximum 1100 W or less, average during
working 600 W or less
DocuPrint 305: Maximum 1100 W or less, average during working
650 W or less
Low power mode: 15 W or less, Sleep mode: 10 W or less
(220 - 240 V), 5 W or less (120 V)
(For this product, there will be no power consumption when the
electric plug is inserted into the power outlet but the switch is
switched off.)
Dimensions
DocuPrint 205: 505 (W) × 376 (D) × 324 (H) mm
DocuPrint 255/305: 505 (W) × 376 (D) × 390 (H) mm
146
A Appendix
Item
Contents
Weight
(including drum/toner cartridge)
DocuPrint 205: 21.6 kg
DocuPrint 255/305: 23.6 kg
Printable Area
Top edge 4 mm
Unprintable area
Printable area
Left 4 mm
Right 4 mm
Bottom edge 4 mm
A.1 Specifications
147
A.2
Optional Accessories and Consumables
Optional Accessories
The main optional accessories are as follows. Contact our Customer Support Center or your
dealers to order these.
Product name
Product
code
Reference
Additional hard disk
E3300052
Allows you to use Secure Print and Sample
Print features. The additional memory
(optional) must be installed to use this
accessory.
Additional memory (128MB)
E3300053
Additional memory (256MB)
E3300061
Essential when installing the hard disk and the
PostScript software kit. The additional
memory may also be essential to enable 2
sided printing depending on the paper size to
be printed (For example, printing on 2 sides of
A3 size paper in high resolution).
A3 universal tray (250)
EL300305
Paper tray that can be loaded up to 250
sheets of standard paper (P paper).
When combined with the A3 universal tray
(550), you can install up to two levels of paper
trays.
A3 universal tray (550)
EL300306
Paper tray that can be loaded up to 550
sheets of standard paper (P paper).
When combined with the A3 universal tray
(250), you can install up to two levels of paper
tray.
Duplex unit
EL300304
Can handle 2 sided printing. The additional
memory may also be essential to enable
duplex printing depending on the paper size to
be printed (For example, printing on 2 sides of
A3 size paper in high resolution).
Rear tray
E3300057
For reducing the curling of paper when
printing heavyweight paper.
Can be installed to DocuPrint 255/305.
Offset catch tray
E3300058
Allows you to shift the output position for each
job (offset output).
Can be installed to DocuPrint 255/305.
Multi bypass feeder
E3300059
For feeding paper manually. Can be loaded
instead of tray 1.
PostScript software kit
E3300060
To enable this printer as a
PostScript-compatible printer. Allows you to
use the PDF Bridge feature, and also allows
you to print from Macintosh as well. The
additional memory (optional) must be installed
to use this accessory.
SC/TC Font ROM
E3300063
Allows you to print in the ESC/P emulation
mode.
KR Font ROM
E3300062
Allows you to print in the KSSM emulation
mode.
The product type and code is as of December 2003.
148
A Appendix
Consumables
This section explains how to handle the types of consumables. For details on the
replacement procedure of the consumables, refer to the procedure listed in the packaging
box of the consumables and “6.1 Replacing the Drum/Toner Cartridge” (P. 124).
Important
• If you are not using the consumables recommended by our company, the performance of the machine
may not be at its optimum level. Use the consumables recommended for this product.
Types of Consumables
Note
• The drum/toner cartridge (6K) is bundled with this printer at the time of purchase. The drum/toner
cartridge (6k) cannot be ordered separately.
• For details on the life of the drum/toner cartridge, refer to “Appendix A.3 Life of Consumables and
Regular Replacement Parts” (P. 150).
Types of consumables
Drum/toner cartridge 10K
Product code
Form
CT350251
1 unit per box
Handling Consumables
• Do not store the consumables with the packaging box standing on end.
• Before using the consumables/maintenance products, do not open the packaging and
avoid storing them in the following locations:
• Locations with high temperature and humidity
• Locations near open flame
• Locations with direct exposure to sunlight
• Dusty locations
• Read the handling instructions on the packaging box or container carefully before using
the consumables.
• It is recommended to keep some spares of the consumables.
• Check the product codes of the consumables first before contacting our Customer
Support Center or your dealers to order.
Regular Replacement Parts
The regular replacement part is as follows.
Product name
Product code
Maintenance kit (DP205 220 V)
E3300064
Maintenance kit (DP205 110 V)
E3300066
Maintenance kit (DP255/305 220 V)
E3300067
Maintenance kit (DP255/305 110 V)
E3300068
Reference
Maintenance kit includes the fuser unit,
transfer roll cartridge, and feed roll.
A.2 Optional Accessories and Consumables
149
A.3
Life of Consumables and Regular
Replacement Parts
Life of Consumables
Product name
Possible number of pages printed
Drum/toner cartridge (6K)
About 6,000 sheets
Drum/toner cartridge (10K)
About 10,000 sheets
Note
• The possible number of pages that can be printed with the drum/toner cartridge is the number of pages
printed continuously at a print ratio of 5% using A4
size paper.
• The possible number of pages that can be printed differs according to factors such as the print contents,
paper size, paper type, environment used, and the frequency that the printer is switched on and off.
Life of Regular Replacement Parts
Product name
Lifespan
Fuser unit
About 100,000 sheets
Transfer roll cartridge
About 200,000 sheets
Feed roll
About 200,000 sheets
Note
• The number of sheets listed under lifespan is the number of pages that can be printed continuously
using A4
size paper.
• As the lifespan differs according to factors such as the print contents, paper size, paper type,
environment used, and the frequency of switching on/off the power to the printer, think of it as a
guideline.
• Service engineer will replace the regular replacement parts. Customers may also replace them.
Functional Parts
Our company will keep the functional parts (parts essential for the machine functions) of the
printer for replacement for 7 years after we have stopped manufacturing it.
150
A Appendix
A.4
How to Obtain Product Information
Latest Printer Driver
You can download the latest printer driver from the web site of our company.
Note
• Please take note that the communication cost will be borne by the customers.
1.
Click [About] on the [Detailed Settings] tab of the printer properties dialog box.
2.
Click the [Fuji Xerox Web Site] button. The web browser will be activated and the web
site displayed.
3.
Following the instruction, download the corresponding printer driver.
Note
• The address (URL) of the download service page of our company is as follows:
http://www.fxap.com.sg/suppdrv.jsp
• For details on the latest printer driver features, refer to the Online Help for the printer driver.
Upgrading the Firmware Version of This Printer
Our company provides the tool to upgrade the version of the software built into this printer
(known as firmware) from the computer.
The latest firmware and upgrade utility can be obtained from the web site address (URL)
listed below.
Download the corresponding firmware by following the instructions on the web site.
http://www.fxap.com.sg/suppdrv.jsp
Note
• Please take note that the communication cost will be borne by the customers.
A.4 How to Obtain Product Information
151
A.5
Output Size and Memory Capacity
The memory capacity required for a print job differs according to the print mode settings on
the printer driver and the output size for printing. Values of the required memory capacity
also differ according to the usage environment of this printer. Refer to the table below for
the memory capacity and send your print job.
Important
• Memory may not be sufficient depending on the print data. Install sufficient memory to handle for large
jobs.
Note
• The required memory capacity differs according to the type of printer driver.
• The memory capacities shown in the table are factory defaults. Required memory capacity differs
according to the protocol activation status and receive buffer size.
PCL Printer Driver
Memory capacity
1 sided print (Unit: MB)
Possible output
Guaranteed*1
output
Possible output
Guaranteed*1
output
A5
64
64
64
64
B5
64
64
64
64
A4
64
64
64
64
B4
64
64
64
64
A3
64
64
64
64
Custom
64
64
64
64
Long paper
(305 × 900 mm)
64
192
-
-
A5
64
64
64
64
B5
64
64
64
192
A4
64
64
64
192
B4
64
192
64
320
A3
64
192
192
320
Custom
192
320
192
320
Long paper
(305 × 900 mm)
192
320
-
-
Print
mode
Standard
High
Resolution
Paper size
: The additional memory (optional) (128 MB) must be installed.
: The additional memory (optional) (256 MB) must be installed.
*1: Outputs may not be guaranteed fully depending on the original documents.
152
Memory capacity
2 sided print (Unit: MB)
A Appendix
PostScript Printer Driver
Memory capacity
1 sided print (Unit: MB)
Possible output
Guaranteed*1
output
Possible output
Guaranteed*1
output
A5
192
192
192
192
B5
192
192
192
192
A4
192
192
192
192
B4
192
192
192
192
A3
192
192
192
192
Custom
192
192
192
192
Long paper
(305 × 900 mm)
192
192
192
192
A5
192
192
192
192
B5
192
192
192
192
A4
192
192
192
192
B4
192
192
192
320
A3
192
192
192
320
Custom
192
320
192
320
Long paper
(305 × 900 mm)
192
320
-
-
Print
mode
Standard
High
Resolution
Memory capacity
2 sided print (Unit: MB)
Paper size
: The additional memory (optional) (128 MB) must be installed.
: The additional memory (optional) (256 MB) must be installed.
*1: Outputs may not be guaranteed fully depending on the original documents
A.5 Output Size and Memory Capacity
153
A.6
Precautions and Limitations
Precautions and Limitations of This Printer
This section explains the precautions and limitations of using this printer.
Optional Hard Disk
• Additional memory must be installed when the hard disk (optional) is installed on the
printer
• When the hard disk is installed, the printer may assume that data in the hard disk is
corrupted if power is cut off when the printer is in use.
• When the hard disk is installed, the hard disk can be specified as a storage location for
print data from LPD, SMB and IPP. PCL, HP-GL and HP-GL/2 forms are stored in the
hard disk. The storage location for the forms cannot be changed.
• Data that will be deleted during initialization includes the additional fonts, the PCL,
HP-GL, and HP-GL/2 forms, and SMB folders. Secure/Sample/Delayed Print documents
and their logs will not be deleted.
When Print Result Is Different From the Settings
The print result may differ in the following ways from the settings due to insufficient print
page buffer. In this case, we recommend you increase the memory capacity.
• Document is printed on one side although duplex printing is specified
• Job is canceled (where a page in the job cannot be expanded in the print page buffer)
Optional Accessories
• The hard disk (optional) must be installed in order to use the secure, sample, delayed
print, and page print mode features.
• The optional PostScript software kit is required to use this printer as a PostScript
supported printer.
Meter Count in 2 Sided Printing
When printing two sided documents, blank sheets may be automatically inserted into the
document depending on the number of copies specified and the application used. Blank
sheets inserted by the application will be counted as 1 page.
154
A Appendix
Usable Paper
The usable sizes of paper that can be used with this printer are shown in the following table.
Output tray
Paper feeding tray
Paper size and
orientation
Tray1
Tray2 - 4
Bypass
tray
Duplex
unit
Center
output tray
Rear tray
Offset
catch tray
A3
A4
*1
A4
A5
A5
*1
B4
B5
B5
11 × 17"
*1
Legal 14 (8.5 × 14")
Legal 13 (8.5 × 13")
Letter (8.5 × 11")
*1
*1
Letter (8.5 × 11")
7.25 × 10.5"
7.25 × 10.5"
COM 10 envelope
*1
5.5 × 8.5"
*1
5.5 × 8.5"
*1
Monarch envelope
*1
Monarch envelope
*1
C5 envelope
*1
C5 envelope
*1
DL envelope
*1
DL envelope
*1
Custom paper size
*1
*3
*3
: Usable
: Usable as a custom size paper
: Not usable
*1: Set the paper size indicator to <Custom>.
*2: The printing quality cannot be guaranteed.
*3: The 297 mm or longer paper cannot be used. The paper is ejected to the center output tray.
A.6 Precautions and Limitations
155
TIFF File Format
Supported TIFF formats are as follows.
BitPer
Sample
1
Photometric
Interpretation
WhiteIsZero
Compression
Multi-value color JPEG/
PackBits, RGB Palette
Uncompressed (1)
{
G3 FAX (3)
{
G4 FAX (4)
{
LZW (5)
BlackIsZero
PackBits (32773)
{
Uncompressed (1)
{
G3 FAX (3)
{
G4 FAX (4)
{
LZW (5)
4
8
PackBits (32773)
{
WhiteIsZero
Uncompressed (1)
{
BlackIsZero
Uncompressed (1)
{
WhiteIsZero
Uncompressed (1)
{
LZW (5)
BlackIsZero
JPEG (6)
{
JPEG (7)
{
PackBits (32773)
{
Uncompressed (1)
{
LZW (5)
JPEG (6)
{
JPEG (7)
{
PackBits (32773)
{
ITULAB
JPEG (7)
{
RGB Palette (3)
Uncompressed (1)
{
LZW (5)
JPEG (6)
JPEG (7)
PackBits (32773)
8,8,8,8
CMYK (5)
Uncompressed (1)
LZW (5)
JPEG (6)
JPEG (7)
PackBits (32773)
156
A Appendix
{
BitPer
Sample
8,8,8
Photometric
Interpretation
RGB (2)
Compression
Uncompressed (1)
Multi-value color JPEG/
PackBits, RGB Palette
{
LZW (5)
JPEG (6)
JPEG (7)
PackBits (32773)
YCbCr (6)
{
Uncompressed (1)
LZW (5)
JPEG (6)
{
JPEG (7)
{
PackBits (32773)
ITULAB (10)
Uncompressed (1)
{
LZW (5)
JPEG (6)
JPEG (7)
{
PackBits (32773)
A.6 Precautions and Limitations
157
A.7
Printing Using the Serial Interface
When printing using the serial interface, you need to specify the following settings on the
printer and the printer driver.
Settings on the Printer
Set the following settings using the control panel.
Refer to
• For details about each items on the control panel: “Serial” (P. 77)
1.
Press the <Menu> button to display the Menu screen.
2.
Select [Admin Menu] > [Network/Port] > [Serial] > [Port Status] by pressing the < >
< > < > buttons.
3.
Set [Port Status] to [Enable].
4.
According to the environment to use, set the size of receive buffer memory at [Buffer
Size] setting of [Allocate Memory] (default: 64 MB).
5.
Set the parameters at [Admin Menu] > [Network/Port] > [Serial] (required).
„ Example for using this printer as a PostScript printer
Print Mode:
PS
Adobe Protocol: Standard
Baudrate:
9600bps
Stop Bit:
1bit
Parity:
Not Available
Xon-Xoff Control: On
DTR Control:
Fix-High (when the host computer is Windows)
„ Example when printing the print job that includes binary data such as PCL, TIFF, and
PDF
Baudrate:
9600bps
Stop Bit:
1bit
Parity:
Not Available
Xon-Xoff Control: Off (set this item to Off when the print job includes binary data)
DTR Control:
Active-High (when the host computer is Windows)
Note
• Change [Adobe Protocol], [Baudrate], [Stop Bit], and [Parity] as needed. It is necessary to accommodate
the port setting of the printer driver to that of the printer.
• When doing hardware flow control (when setting [DTR Control] to [Active-High] or [Active-Low]), the
cable must be connected correctly to the signaling channel.
• When not doing hardware flow control, set [DTR Control] to [Fix-High] or [Fix-Low]. When using the
general Windows computer, set to [Fix-High].
• When not doing the hardware flow control, printing may not be executed correctly because of lost data.
158
A Appendix
Settings on the Printer Driver
The procedure here explains with Windows XP as an example.
1.
Set the port that is used when installing to COM n (n=1, 2, 3,…).
2.
After installation, click [Start] on the taskbar, then select [Printers and Faxes].
3.
Click the icon of this printer, and then select [Properties] from the [File] menu.
4.
Click the [Ports] tab to confirm the port that is specified when installation is set, then
click [Configure Port].
5.
Set each item.
Bit/Sec:
Select the value of Baudrate that is set on the printer.
Data bit:
Select [8].
Parity:
Select the value that is set on the printer.
Stop bit:
Select the value that is set on the printer.
Flow control: Select [None] when the flow control is not enabled. Select [Xon/Xoff]
when setting [Xon-Xoff Control] to [On] on the printer. Select [Hardware]
when setting [DTR Control] to [Active-High] on the printer.
6.
Click [OK].
7.
Click [OK] in the printer properties dialog box.
A.7 Printing Using the Serial Interface
159
A.8
Glossary
100BASE-TX
An extension of 10BASE-T and a predominant form of FastEthernet. Its transmission speed
is 100 Mbps, a great jump in speed from 10 Mbps of 10BASE-T.
10BASE-T
The 10Base-T system uses a twisted-pair cable, base band transmission and operates at
10 Mbps. It is one of the IEEE802.3 standard for Local Area Networks (LAN).
Address
Information (unique identifier) that is assigned to recognize nodes (each computer or
terminal) on the network. Individually assigned location of data in a memory is also called
address.
Application software
Software that acts as a tool to carry out operations on the computer. There are many types
of application software available, such as word processors, spreadsheets, graphics
software, and databases.
Bi-directional communication
Communication between two machines, mutual sending and receiving of information with
each other. By bi-directional communication, you can send print data from the computer as
well as send information, such as print status from the printer to the computer.
Browser
Software to display and view at your computer, information on the Internet. Typical
browsers include Netscape Communicator and Internet Explorer.
CD-ROM
A compact disc (CD) with data such as software and graphics stored to be used by a
computer.
Click
To press the mouse button once and then release. In this manual, clicking the left mouse
button is known as “click” and clicking the right mouse button is known as “right-click”.
To press the mouse button twice quickly and then release is known as “double-click”.
Collate
When printing multiple copies, the outputting of each set in the sequence of pages 1, 2,
3,...1, 2, 3... is known as “collating”.
Common menu
Makes up of meter check, reports/lists, system settings, network/port settings, memory
settings, initialize/delete data and printer settings. It is a menu where common settings can
be made in all print modes.
Default
Settings made during factory shipment and NV memory initialization.
DHCP
Abbreviation of Dynamic Host Configuration Protocol, a protocol that automatically
allocates IP address from DHCP server to DHCP client.
160
A Appendix
DNS
Abbreviation of Domain Name System, a data query service chiefly used on the Internet for
translating host names into Internet addresses.
dpi
Abbreviation of dot per inch, a unit expressing the number of dots that can be printed in a
width of 1 inch (about 25.4 mm). Used as a unit expressing resolution.
Driver
A device to spin the disk. Types of drivers available include floppy disk drive, CD-ROM
drive, and hard disk drive.
Emulation
The ability of the printer to perform and achieve a similar print result as other printers. This
mode is known as emulation mode.
EtherTalk
One of the communication protocols of AppleTalk, a Macintosh network software.
Font
Style of typeface and characters. Refers to one set of characters with similar designs.
FQDN
Abbreviation of Fully Qualified Domain Name, the full name of a system, consisting of its
local host name and its domain name in a TCP/IP network.
G.S.M.
Weight of a 1 m2 sheet of paper.
Gradation
The smoothness between colors. It is expressed in gradation value by the number of steps
of gradation, and the greater the value, the smoother it is.
HTTP
A protocol used to communicate with WWW server over the Internet.
Install
To incorporate software or hardware into the computer and peripherals to make it useable.
It can be used to describe incorporating software such as printer driver into the computer
system as well as incorporating the network extension card into the printer.
In this manual, install is mainly used to describe incorporating software into the computer.
Interface
The part that connects different systems (series). It is often used when describing the
connection between computer and printer as well as between human and machine.
In interface specifications, especially electrical specifications, it is also simply known as
interface.
Interface cable
Cable for mutually connecting multiple machines together.
The types of cables available are parallel cable or USB cable (for directly connecting printer
and personal computer), and Internet cable (for connecting printer to network).
A.8 Glossary
161
IP address
An address for a computer or device on a TCP/IP network. The format of an IP address is
a 32-bit numeric address written as four numbers separated by periods.
IPP
A protocol for printing using HTTP.
JavaScript
A scripting language developed by Netscape Communications and executable on web
browsers.
Job
A series of processes carried out by the computer. For example, processing the printing of
one file is known as one print job. Canceling and outputting of printing are carried out in this
unit of job.
Local printer
In this manual, a printer that is directly connected to a computer via parallel or USB cables
is known as a “local printer”.
Login
A state where you can access resources (such as network hard disk or printers) on the
computer system. Ending a login session is known as “log out”.
Mode menu
Consisting of the PCL, HP-GL and HP-GL/2 emulation modes, the mode menu is a menu
for setting the conditions pertaining to each emulation mode.
Multiple Up
A feature to print multiple pages on a piece of paper.
NetWare
A network OS developed by Novell.
Network path
The route to a computer or file on the “network”.
It is used in cases as such when specifying a server name.
Network printer
In this manual, a printer that is connected to the network via Ethernet cables is known as a
“network printer”.
Online Help
Manual displayed on the computer screen.
OS
Abbreviation of Operating System, a software that controls and manages the basic activities
of the hardware and software of the computer. It is a base to operate other software, such
as application software.
Parallel interface
One data transmission method between the computer and peripherals. Transmit multiple
bits of data simultaneously. A typical parallel interface is the Centronics, which is used to
connect between the computer and the peripherals, such as the printer.
162
A Appendix
PDF File
In this manual, PDF file refers to the online document created by Acrobat, a software
developed by Adobe Systems Incorporated in the United States. To display a PDF file, you
need to have Adobe Acrobat Reader installed on your computer.
Port
Connection that allows the computer and the peripherals to exchange information.
Port9100
A network communication method able to send data on Windows 95/Windows 98/Windows
Me/Windows 2000/Windows XP/Windows Server 2003. For Windows 95/Windows 98/
Windows Me, the TCP/IP Direct Print Utility (Utility software is supplied by Fuji Xerox) must
be installed.
For Windows 2000/Windows XP/Windows Server 2003, Port9100 can be used on the
standard TCP/IP port monitor.
Print page buffer
Location that actually processes and stores print data.
Printable area
Area of a sheet of paper that can actually be printed on.
Printer driver
Software that converts data created by application software to data that can be interpreted
by the printer.
Protocol
An agreed-upon format for transmitting data between multiple devices and the computer
system. It is an agreed procedure to transfer information between hardware or
communicate between two network computers.
Receive buffer
A buffer is a temporary location to store data sent from the computer. Increasing the
memory capacity of the receive buffer will free up the computer sooner.
Resolution
Describes the fineness of graphics. Normally, it is expressed in number of dots per inch
(unit: dpi) and the greater this value, the higher is the resolution.
Server
A computer that stores information on the network and provides a service to other
computers.
Conversely, a computer that requests services from the server is known as a “client”.
SMB
A network communication method able to send data on Windows network (Microsoft
network). It can be used on Windows 95/Windows 98/Windows Me/Windows NT 4.0/
Windows 2000/Windows XP/Windows Server 2003.
A.8 Glossary
163
SNMP
A protocol that manages devices connected to the network. SNP works through the SNMP
manager and SNMP agents.
SNMP manager is software that manages devices, and SNMP agents are the devices that
are managed.
Software
Program to operate the computer. Software includes the OS as well as application software.
TCP/IP
A network protocol developed by DARPANET (Defense Advanced Research Project
Agency NetWork). It is a standard Internet protocol that is used in various products from
personal to large computers.
USB
Abbreviation of Universal Serial Bus, a data transmission method between the computer
and peripherals. It supports the Hot Plug feature (allows connection to be made with power
switched on) that can connect the computer and peripherals easily.
Web screen
In this manual, the screen that displays data using the web browser is known as the web
screen.
WINS
Abbreviation of Windows Internet Name Services, a system that determines the IP address
associated with a network computer in TCP/IP environment.
WWW
Abbreviation of World Wide Web. The system that provides web sites on the Internet.
164
A Appendix
Index
Symbols, Numerics
D
< > < > < > < > buttons . . . . . . . . . 15, 96
date settings . . . . . . . . . . . . . . . . . . . . . . . . . 88
Delayed Print . . . . . . . . . . . . . . . . . . . . . . . . . 38
direct printing of PDF file . . . . . . . . . . . . . . . . 40
Domain List . . . . . . . . . . . . . . . . . . . . . . . . . 128
drum/toner cartridge . . . . . . . . . . 14, 124, 150
duplex unit . . . . . . . . . . . . . . . . . . . . . . . 13, 148
A
A3 universal tray . . . . . . . . . . . . . . . . . . 13, 148
additional memory . . . . . . . . . . . . . . . . . . . . 148
Admin Menu . . . . . . . . . . . . . . . . . . . . . . . . . 76
Alert Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Allocate Memory . . . . . . . . . . . . . . . . . . . . . . 92
automatic tray selection . . . . . . . . . . . . . . . . . 62
B
Banner Sheet . . . . . . . . . . . . . . . . . . . . . . . . . 88
Buffer Size . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . 13
C
<Cancel Job> button . . . . . . . . . . . . . . . . 15, 18
canceling printing . . . . . . . . . . . . . . . . . . . . . . 18
center output tray . . . . . . . . . . . . . . . . . . . . . . 12
CentreWare Internet Services
procedure . . . . . . . . . . . . . . . . . . . . . . . . . 132
settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
troubles in use . . . . . . . . . . . . . . . . . . . . . 121
using online help . . . . . . . . . . . . . . . . . . . 132
changing low power mode settings . . . . . . . . 68
changing sleep mode settings . . . . . . . . . . . . 68
checking printed pages
Print Meter . . . . . . . . . . . . . . . . . . . . . . . . 137
Print Meter Report . . . . . . . . . . . . . . . . . . 137
checking printer status via E-mail . . . . . . . . 134
checking status of print data . . . . . . . . . . . . . 19
checking/managing the printer status on a web
browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
cleaning the feed roll . . . . . . . . . . . . . . . . . . 141
cleaning the printer . . . . . . . . . . . . . . . . . . . 139
configuring optional accessories . . . . . . . . . . 20
consumables
life of consumables . . . . . . . . . . . . . . . . . 150
replacement procedure of
consumables . . . . . . . . . . . . . . . . . . . . . . 149
types of consumables . . . . . . . . . . . . . . . 149
ContentsBridge Utility . . . . . . . . . . . . . . . . . . 40
control panel . . . . . . . . . . . . . . . . . . 12, 15, 65
control panel setting
changing menu settings . . . . . . . . . . . . . . . 67
description of menu items . . . . . . . . . . . . . 71
menu list . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
cover A . . . . . . . . . . . . . . . . . . . . . . . . . 14, 101
cover B . . . . . . . . . . . . . . . . . . . . . . . . . 14, 101
cover C . . . . . . . . . . . . . . . . . . . . . . . . . 13, 101
cover D . . . . . . . . . . . . . . . . . . . . . . . . . 13, 101
E
<Eject/Set> button . . . . . . . . . . . . . . . . . . 15, 96
E-mail Printing . . . . . . . . . . . . . . . . . . . . . . . . 50
error codes . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Error History Report . . . . . . . . . . . . . . . . . . . 127
<Error> indicator . . . . . . . . . . . . . . . . . . . . . . 15
Ethernet settings . . . . . . . . . . . . . . . . . . . . . . 86
EtherTalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
extension output tray . . . . . . . . . . . . . . . . 12, 14
F
feed roll . . . . . . . . . . . . . . . . . . . . . . . . 141, 150
Fonts List . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
forced printing . . . . . . . . . . . . . . . . . . . . . . . 106
Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
functional parts . . . . . . . . . . . . . . . . . . . . . . 150
fuser unit . . . . . . . . . . . . . . . . . . . . . . . . 14, 150
G
Gateway Address . . . . . . . . . . . . . . . . . . . . . 85
glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
H
hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
HPGL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
HP-GL/2 logical printer settings . . . . . . . . . . 128
HP-GL/2 Logical Printers/Stored Jobs
List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
HP-GL/2 Settings List . . . . . . . . . . . . . . . . . 128
I
Init/Del Data . . . . . . . . . . . . . . . . . . . . . . . . . . 94
InternetServices . . . . . . . . . . . . . . . . . . . . . . . 85
IP address
Get IP Address . . . . . . . . . . . . . . . . . . . . . . 85
IP address . . . . . . . . . . . . . . . . . . . . . . . . . 85
limit IP address . . . . . . . . . . . . . . . . . . 86, 133
IPP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
J
Job History Report . . . . . . . . . . . . . . . . . . . . 127
L
LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . 15
loading paper
loading custom size paper . . . . . . . . . . . . . 27
Index
165
Mail Notice Service . . . . . . . . . . . . . . . . . . . 134
memory capacity . . . . . . . . . . . . . . . . . . . . . 152
<Menu> button . . . . . . . . . . . . . . . . . . . . 15, 96
message list . . . . . . . . . . . . . . . . . . . . . . . . . 111
moving the printer . . . . . . . . . . . . . . . . . . . . 143
multi bypass feeder . . . . . . . . . . . . . . . . . . . 148
print confidential document . . . . . . . . . . . . . . 32
Print Meter . . . . . . . . . . . . . . . . . . . . . . . 94, 137
Print Meter Report . . . . . . . . . . . . . . . . . . . . 127
print the job history report automatically (Auto Job
History) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
printable area . . . . . . . . . . . . . . . . . . . . . . . . 147
printer driver
latest printer driver . . . . . . . . . . . . . . . . . . 151
to display Online Help . . . . . . . . . . . . . . . . 21
printing from web browser . . . . . . . . . . . . . . . 48
printing on custom size paper/long paper . . . 27
printing on transparencies . . . . . . . . . . . . . . . 25
printing reports/lists . . . . . . . . . . . . . . . . . . . 129
printing using the serial interface . . . . . . . . . 158
printing via e-mail . . . . . . . . . . . . . . . . . . . . . . 50
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
N
R
NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Network/Port . . . . . . . . . . . . . . . . . . . . . . . . . 76
<Ready> indicator . . . . . . . . . . . . . . . . . . . . . 15
rear output tray lever . . . . . . . . . . . . . . . . . . . 13
rear tray . . . . . . . . . . . . . . . . . . . . . . . . . 13, 148
regular replacement parts . . . . . . . . . . . . . . 150
replacing the drum/toner cartridge . . . . . . . . 124
reports/lists . . . . . . . . . . . . . . . . . . . . . . . . . 127
loading envelopes . . . . . . . . . . . . . . . . . . .
loading paper in a paper tray . . . . . . . . . . .
loading paper in the bypass tray
(optional) . . . . . . . . . . . . . . . . . . . . . . . . . .
loading transparencies . . . . . . . . . . . . . . . .
long paper . . . . . . . . . . . . . . . . . . . . . . . . . . .
low power mode . . . . . . . . . . . . . . . . . . . 18,
LPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
59
61
25
27
87
78
M
O
offset catch tray . . . . . . . . . . . . . . . . . . . 13, 148
<Online> button . . . . . . . . . . . . . . . . . . . . . . . 15
Online Help
(CentreWare Internet Services) . . . . . . . . . . 132
Online Help (printer driver) . . . . . . . . . . . . . . 21
optional accessories . . . . . . . . . . . . . . . . . . 148
[Options] tab . . . . . . . . . . . . . . . . . . . . . . . . . 20
P
paper
storing and handling paper . . . . . . . . . . . . 58
unusable paper . . . . . . . . . . . . . . . . . . . . . 58
usable paper . . . . . . . . . . . . . . . . . . . . . . . 55
paper jams . . . . . . . . . . . . . . . . . . . . . . . . . . 101
paper meter . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Paper Name . . . . . . . . . . . . . . . . . . . . . . . . . 91
Paper Priority . . . . . . . . . . . . . . . . . . . . . . . . . 90
parallel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
PCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
PCL Form List . . . . . . . . . . . . . . . . . . . . . . . 128
PCL Settings List . . . . . . . . . . . . . . . . . . . . . 128
PDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
PDF Bridge . . . . . . . . . . . . . . . . . . . . . . . 40, 71
PDF Settings List . . . . . . . . . . . . . . . . . . . . . 127
poor print quality . . . . . . . . . . . . . . . . . . . . . 108
Port9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
PostScript Fonts List . . . . . . . . . . . . . . . . . . 128
PostScript logical printer settings . . . . . . . . 128
PostScript Logical Printers List . . . . . . . . . . 128
PostScript software kit . . . . . . . . . . . . . . . . . 148
<Power Saver> button/indicator . . . . . . . . . . 15
power saver modes . . . . . . . . . . . . . . . . . . . . 18
power switch . . . . . . . . . . . . . . . . . . . . . . . . . 12
precautions and limitations . . . . . . . . . . . . . 154
print after checking printing result - Sample
Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
print at a specified time . . . . . . . . . . . . . . . . . 38
166
Index
S
Sample Print . . . . . . . . . . . . . . . . . . . . . . . . . 35
Secure Print . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
setting custom paper sizes . . . . . . . . . . . 29, 63
setting paper types (control panel) . . . . . . . . 64
setting permitted domain . . . . . . . . . . . . . . . . 54
sleep mode . . . . . . . . . . . . . . . . . . . . . . . 18, 87
SMB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
special media . . . . . . . . . . . . . . . . . . . . . . . . . 57
specifications . . . . . . . . . . . . . . . . . . . . . . . . 144
standard paper . . . . . . . . . . . . . . . . . . . . . . . . 56
Stored Documents List . . . . . . . . . . . . . . . . 128
Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . . 85
Substitute Tray . . . . . . . . . . . . . . . . . . . . . . . . 89
switching off the power . . . . . . . . . . . . . . . . . 17
switching on the power . . . . . . . . . . . . . . . . . 17
System Settings List . . . . . . . . . . . . . . . . . . 127
T
TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . 85
TIFF file . . . . . . . . . . . . . . . . . . . . . 48, 53, 156
TIFF logical printer settings . . . . . . . . . . . . . 127
TIFF Logical Printers List . . . . . . . . . . . . . . . 127
TIFF Settings List . . . . . . . . . . . . . . . . . . . . . 127
time settings . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
transfer roll cartridge . . . . . . . . . . . . . . . 14, 150
tray 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tray Priority . . . . . . . . . . . . . . . . . . . . . . . . . . 90
troubleshooting . . . . . . . . . . . . . . . . . . . . . . 101
U
upgrade
firmware . . . . . . . . . . . . . . . . . . . . . . . . . . 151
latest printer driver . . . . . . . . . . . . . . . . . . 151
UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
W
WINS server settings . . . . . . . . . . . . . . . . . . . 85
Index
167
Customer Response Sheet
DocuPrint 205/255/305 User Guide (ME3208E2-1)
To improve our publications, we would appreciate your feedback regarding this guide. Please take a
few moments to complete and return this form to us.
z About Yourself
1. How often do you use this guide?
[ ] Daily [ ] Weekly [ ] Monthly
[
] Infrequently
2. When do you usually refer to the guide?
[ ] Doing a usual operation [ ] Using unfamiliar features
[ ] Solving a problem
3. Which part of the guide do you read frequently?
Chapter/Section/Page:
4. Where do you keep this guide?
5. (Optional)
Your Name:
Company or organization:
Address:
Occupation:
z About the Guide
Strongly
agree
1. It is handy.
1
2. It is easy to read.
1
3. Titles of chapters and sections make sense.
1
4. Information is logically placed.
1
5. Referencing is easy.
1
6. Content is easy to understand.
1
7. The step-by-step instructions are easy to follow.
1
8. All necessary information is included.
1
9. Illustrations aid in the understanding of content.
1
10. The use of color is effective.
1
Neutral
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
Strongly
disagree
5
5
5
5
5
5
5
5
5
5
Other comments:
After completing this form, detach and send it to the address below.
(Please use your own envelope and postage stamp.)
Thank you for your cooperation.
Fuji Xerox Co., Ltd.
KSP R&D 2D7
3-2-1, Sakado, Takatsu-ku
Kawasaki-shi, Kanagawa-ken
JAPAN 213-0012.
DocuPrint 205/255/305 User Guide
Human Interface Design Development
Document Products & Supply Company
Fuji Xerox Co., Ltd.
ME3208E2-1 (Edition 1)
Copyright 2003 by Fuji Xerox Co., Ltd.
©
">