Tartarini Auto LPG/CNG Sequential Fuel System User Manual

INSTALLATION MANUAL
OF THE
LPG/CNG
SEQUENTIAL FUEL SYSTEM
Tartarini Auto S.p.a
Via Bonazzi 43 40013 Castel Maggiore (Bo) Italy
Tel.:+39 051 632 24 11 Fax: 051 632 24 00
E-mail: [email protected] www.tartariniauto.it
May 2005
CONTENTS:
THE 10 RULES ………………………………………………………………….. 3
SYSTEM DESCRIPTION ........………………………………………………… 4
THE REGULATORS .…………………………………………………………… 5
INTERCEPTION SOLENOID VALVE……………...………………………….. 6
THE RAIL OF INJECTORS.…………………………………………………….7/9
CALIBRATED NOZZLE .………………………………………………………. 10
LAMBDA PROBE.. …………………………………………………………….. 11
PRESSURE METER…....................………………………………………….. 12
THE HARNESS and CONTROL UNIT…...…………………………………... 13
RULES FOR A CORRECT INSTALLATION....……………………………… 16
INSTALLATION SAFETY INSTRUCTIONS…........................……………... 17
THE PROGRAMME….………….…….…………………………….………….. 17
TROUBLE SHOOTING ......................................................................………40
ERROR CODES………………..........................................................……… 41
MAINTENANCE SCHEDULE………………………….........................……… 42
2
THE 10 RULES
1) “MATRIX” injectors unit: the gas injection time when the engine is running at
minimum must not be less than 3 ms.
“TARTARINI” injectors unit type 03: the gas injection time when the engine is
running at minimum must not be less than 4 ms.
2) SEQUENTIAL: the gas injection time at full load (6000 rpm) must be less than 20
ms, better still if less than 18 ms.
SEMI-SEQUENTIAL: the gas injection time at full load (6000 rpm) must be less than
10 ms.
3) LPG injection pressure = 1 bar
4) CNG injection pressure = 1,8 bar
5) The emulation cable is marked with letter A. When installing it, match it with letter A
of the injectors unit.
6) The rubber hose that takes the gas from the rail into the suction manifold must be
as short as possible.
7) The vacuum compensating hose to the reducer should be as short as possible
8) The rubber hose that takes the gas from the regulator to the rail must be as short as
possible.
9) Install the “map” pressure sensor with the nozzles facing downwards.
10) The average reducer temperature in partial load driving condition should be
around 60°C.
3
SYSTEM DESCRIPTION
“RAIL MATRIX”
As of the date of the present document, for vehicles with aspirated engines, equipped
with “Sequential LPG/CNG” fuelling system, the homologation covers the displacement
range of 900 to 3720 cm3, for vehicles that comply with directives: 2003/76/EC,
2002/80/EC, 2001/100/EC, 2001/1/CE, 1999/102/EC, 98/69/EC (phase A-B), 96/69/EC,
96/44/EC, 94/12/EEC.
Without limits in displacement, it can be fitted on vehicles that comply with directives
93/59/EEC, 91/441/EEC and previous.
“RAIL MATRIX”
As of the date of the present document, for vehicles with turbo engines, equipped with
“Sequential LPG/CNG” fuelling system, the homologation covers the displacement range
of 1500 to 2500 cm3 for vehicles that comply with the directives: 2003/76/CE,
2002/80/CE, 2001/100/CE, 2001/1/CE, 1999/102/CE, 98/69/CE (phase A-B), 96/69/CE,
96/44/CE, 94/12/CEE.
Without limits in displacement, it can be fitted on vehicles that comply with directives
93/59/EEC, 91/441/EEC and previous.
“RAIL TARTARINI AUTO”
As of the date of the present document, for vehicles with aspirated engines equipped with
“Sequential LPG/CNG” fuelling system, the homologation covers the displacement range
of 1200 to 3060 cm3, for vehicles that comply with directives 2003/76/EC, 2002/80/CE,
2001/100/CE, 2001/1/CE, 1999/102/CE, 98/69/CE (phase A-B), 96/69/CE, 96/44/EC,
94/12/EEC.
Without limits in displacement, it can be fitted on vehicles that comply with directives
93/59/EEC, 91/441/EEC and previous.
The system is the Multipoint Sequential type. It is controlled by an electronic control unit
(also referred to as ECU) that controls the sequence and the injection timing of the Gas. It
injects the gas through the rail of injectors directly into the intake manifolds, thus
dispensing the gas in a particularly precise manner in order to optimise the combustion
process.
The Gas injection timing is obtained by exploiting the petrol injection timing of the original
control unit.
The benefits of this system lie in the following:
1) Compatibility with vehicles having OBD system
2) Optimisation of fuel consumption
3) Optimisation of vehicle driveability
4) Installation simplicity
5) Auto-calibration at minimum
6) Auto-diagnosis
7) Auto-adjustment
4
THE LPG REGULATOR
It consists of:
1) Interception solenoid valve including filter
2) Vacuum fitting
3) Safety valve
4) Gas outlet fitting
5) Heating water inlet and outlet fittings
6) Regulator temperature sensor
The regulator sends the gas at a constant pressure of 1 bar to the rail of injectors and
converts the LPG from liquid into gas.
1
2
3
4
5
6
5
THE CNG REGULATOR
It consists of:
1) Vacuum fitting
2) 1st stage safety valve
3) 2nd stage safety valve
4) Gas outlet fitting
5) Heating water inlet and outlet fittings
6) Regulator temperature sensor connector
This solenoid valve reduces the high pressure from 220 to 1,8 bar and dispenses it
constantly to the rail of injectors.
1
2
5
3
4
6
INTERCEPTION SOLENOID VALVE
1) Electric command pin
2) High pressure gas inlet
3) Connector for gauge that
indicates the amount of gas in
the cylinder.
4) High pressure gas outlet.
1
2
4
3
6
THE INJECTORS RAIL
We suggest to install the injector rail as close as possible to the nozzles in order to
keep the length of the gas tubes as short as possible, compatibly with the space
available in the engine bay.
The nozzles must be screwed into the manifold at t distance between 3 and 15 cm from
the petrol injectors.
For engines with 4 or more valves per cylinder we suggest to install the nozzles slightly
before the petrol injectors in order to allow a proper flow into the manifold before
entering the cylinder.
A filter has been fitted between the regulator and the rail to keep the cavities of the rail
of injectors through which the gas flows clean (see fig. n° 1).
fig. 1
7
Rail “matrix”
This device is controlled by the electronic Gas control unit. It distributes the correct
amount of fuel to each individual cylinder.
1) Gas inlet
2) Electric connector
3) Connection for pressure meter
4) Gauged nozzles for the outlet of Gas towards the manifold
5) Gas temperature sensor connector
2
1
3
4
5
An adhesive plate has been fitted on each Rail of 4 cylinders, (see fig.3) that bears letters
A B C and D. These letters are important as they point out the installation direction of the
Rail.
Each letter will be the reference point of each individual cylinder.
IMPORTANT: Letter A of the Rail must ALWAYS be by letter A of the injector simulator
harness.
fig. 2
8
CALIBRATED NOZZLES FOR MATRIX RAIL
The reference marks that identify the type of nozzle to be
used can be seen on the outer edge of the nozzle, as
illustrated in fig. 6.
RAIL “Tartarini Auto”
6
“TARTARINI AUTO” RAIL
This device is controlled by the electronic Gas control unit. It distributes the correct
amount of fuel to each individual cylinder.
1) Gas inlet
2) Electric connector
3) Connection for pressure meter
4) Gauged nozzles for the outlet of Gas towards the manifold
5) Gas temperature sensor connector
2
1
3
5
4
On the Tartarini Rail you will not find any indication re. the A/B/C/D injectors, since this is
shown on the harness itself and not on the rail.
IMPORTANT: Letter A of the harness must always correspond to letter A of the cut-off
injectors wiring.
9
CALIBRATED NOZZLES FOR TARTARINI RAIL
Rail Tartarini first version
ATTENTION:
The nozzles of the Tartarini Rail “first version” cannot be changed or substituted with other
nozzles of different measures, because the inner diameter is the same for all types. The
calibration of each nozzle is factory set and the suitable requested diameter is shown on
the label (see picture, nr 3 and 7). The diameter of this rail is 3,0 mm, the rail of the first
version is identifiable by the nozzle with double hexagon, see picture n° 4 and 8.
8
7
fig. 3
fig. 4
Rail Tartarini second version
The nozzles of the Tartarini Auto rail “second version” are interchangeable without having
to replace the whole rail.
The rail of the second version is identifiable by the nozzle with single hexagon, see picture
5.
You will see the diameter of the nozzle on a face of the hexagon picture n° 6, n° 9, the
diameter of this nozzle is 3 mm.
3.0
fig. 5
fig. 6
10
9
LAMBDA PROBE
Vehicles with the following Lambda Sensors:
0÷1V 0÷5V 5÷0V 0,8÷1,6V.
Connect the single purple cable to the Lambda probe to view the operating conditions of
the system while driving on the road, especially in OpenLoop.
Use the purple/black cable too on vehicles with two Lambda probes upstream from the
catalyst, connecting it to the Lambda probe of the 2° cylinder row.
Vehicles with the following Lambda Sensors:
UEGO BOSCH type, or NTK type.
Connect the two purple an grey cables (see diagram) to the Lambda probe to view the
operating conditions of the system while driving the vehicle on the road, especially in
OpenLoop.
Use the purple/ black cable and the grey/ black cable on vehicles with two Lambda probes
upstream from the catalyst, connecting them to the Lambda probe of the 2° cylinder row.
ATTENTION: it is not advisable to connect the cables on this type of Lambda probe
unless Tartarini Auto advises you to.
5 Wires Bosch Type UEGO Sensor
see second drawing on following page 5 Wires NTK Type UEGO Sensor
11
PRESSURE METERS
The pressure meter (differential or absolute) informs the gas control unit of the difference
in pressure between the gas injectors and the suction manifolds.
Differential meter
Absolut meter
There are 2 connectors on the bottom of the pressure meter marked Pres. and V.
-Connect the gas pressure tube leading from the rail of gas injectors to the nozzle marked
“Pres”.
-Connect the vacuum tube leading from the suction manifolds to the nozzle marked “V”.
12
THE HARNESS
THE CONTROL UNIT
“Sequential Fuel Injection”
The harness includes:
1) DIAGNOSIS CONNECTOR – required to enter and read data in the Gas ECU.
2) FOUR-PIN CONNECTOR – this is to be connected to the Pressure Meter.
3) TEN-PIN CONNECTOR – this is to be connected to the “injectors simulator”
harness.
4) The ORANGE and the BLACK cables are to be connected to the temperature
sensor of the regulator
5) The ORANGE/BLACK cable and the BLACK cable are to be connected to the GAS
temperature sensor.
6) The WHITE and the GREEN cables are to be connected to the fuel level sensor.
7) The RED/BLACK cables are to be connected to the battery POSITIVE pole.
8) The BLACK cable is to be connected to earth.
9) The BROWN cable is to be connected to the coil negative pole to read RPM
10) The PURPLE cable to the Lambda probe of the 1° cylinder row (upstream from the
catalyst)
11) The GREY cable to the Lambda probe of the 1° cylinder row (upstream from the
catalyst)
12) The PURPLE/ BLACK cable to the Lambda probe of the 2° cylinder row (upstream
from the catalyst)
13) The GREY/ BLACK cable to the Lambda probe of the 2° cylinder row (upstream
from the catalyst)
14) The BLUE cables to the gas position
The remaining cables of the harness are to be individually isolated so that there is no
contact between them.
INJECTORS SIMULATOR HARNESS
How do you know which injectors simulator harness to use?
There are three types of injectors simulator harnesses that can be used with the injection
control unit, namely 4822154 (Straight), 4822182 (Inverted) and 4822155 (Universal).
The two harness types 4822154 and 4822182 have "Bosch" connectors that are to be
connected directly to the original petrol injectors.
Harness type 4822155 has free wires so that it can be connected to any type of injector.
In the case of injectors with Bosch connectors, check the polarity of the connectors of the
petrol injectors to find out whether you should use model 4822154 or 4822182.
13
Follow the instructions below to find out which of the two wires is the positive one:
- Disconnect all the connectors of the injectors.
- Get hold of a multi-meter.
- Put the negative tip on earth.
- Put the positive tip in one of the two contacts of the injector connector.
- Turn the dashboard on and immediately check straight away if the reading is +12Volts.
If the reading is +12 Volt, it means that this is the positive wire.
WARNING, the +12 volts of the injectors is timed, therefore when the dashboard is
switched on it is cut-off again after a few seconds.
We recommend you check the polarity of all the injector connectors to check if any are
inverted.
4822154: This is used if the positive pole of the injectors is on pin n°1 and the
negative pole is on pin n°2. Refer to the drawing if the original connectors are not
numbered.
4822182: This is used if the positive pole of the injectors is on pin n°2 and the
negative pole is on pin n°1. Refer to the drawing if the original connectors are not
numbered.
4822154: If the connectors of the petrol injectors are not the Bosch type or cables type
4822154 and 4822182 are difficult to install, use harness type 4822155 and cut the original
wires of the injectors.
Check which wire is the positive one and which is the negative one following the
instructions given earlier.
The negative wires are the ones to be disconnected.
14
CONNECTORS OF THE PETROL INJECTORS
Follow the diagram above to make the connection.
The connection direction is extremely important. The BLACK striped wires are to go
towards the control unit and the full black ones towards the injectors.
The WHITE/RED wire is to be connected to any of the injector positive poles.
It is important that the petrol injector defined as A is the one of the cylinder where the gas
injector A has been fitted. It doesn’t matter whether it is on the first or the fourth cylinder.
Observe the sequence shown in the diagram for the other injectors.
15
RULES FOR A CORRECT INSTALLATION
Fit the regulator below the height of the expansion tank
Never secure the Rail of injectors to the chassis
Place the regulator as close as possible to the rail
Do not fix the regulator to the dividing panel that separates the engine bay from the
vehicle interior
- Connect the rubber hose (4x11), see picts. 3 and 4, to the end of the safety valves
of the pressure regulators to convey possible gas leaks outside the engine bay,
protecting them from sources of heat or electrical components
- It is not advisable to take the vacuum from pre-existent utilities (petrol pressure
regulators, electric canister valve, servo-brake). A new pick-up point is to be
created 5 cm away from the throttle body
- Do not install the pressure meter near exhausts, as the high temperatures could
cause anomalies.
- Never secure the ECU to the engine, as the strong vibrations involved could
compromise its correct operational efficiency.
Do not place parts of the harness near alternators, high voltage cables, coils, belts,
pulleys, sources of high temperature, such as exhausts for example, as any disturbance
could compromise the correct operational efficiency of the system.
-
LPG Regulator.
Safety Valve Connection
1) Rubber Hose (4x11) Part. #0294620
1
Fig. 3
1
CNG Regulator
Safety Valves connection
1) Rubber Hose (4x11) Part#
0294620
2) T joint Part# 4822211
2
Fig. 4
16
INSTALLATION SAFETY INSTRUCTIONS
-
Disconnect the poles of the battery before starting any electric jobs or before
disconnecting any of the vehicle’s original connectors.
Once the system has been installed, leave the engine running idle without putting
your foot on the accelerator until the solenoid valve energises once, then drive for a
few kilometres on petrol before switching over to gas.
The wires are to be connected by soldering them together.
The soldered parts are to be isolated with heat-shrink sheathing.
Put the fuse in an accessible place for the end user.
THE PROGRAMME
SOFTWARE INSTALLATION PROCEDURE
The “Sequential” programme has to be installed on a computer to be able to program the
ECU.
The minimum configuration of the portable computer to be able to work with this
programme is the following:
Operative system: Windows 98 or higher.
Processor: 133 MHz
RAM: 16 Mb
Hard disk: 25 Mb
CD ROM drive
The programme is self-installing, therefore simply put the disc in the CD ROM drive and
click on “NEXT” three times with the left button of the mouse.
Once the software installation procedure is complete, the following page is displayed. This
page is used to program the ECU of the Sequential system.
17
To display the page that follows, double click on the “Sequential” icon of the desktop.
Click on “File”
To update the
program on line
Click on
“Connection”to
connect or disconnect
the ECU
Click on “Settings”to view
the list of languages in
which the program can
be configured
Click on “Help” to
view the program
version
Letter B means that
the ECU is prearranged for the
auto-adjustment
function
ECU connected
should be
displayed
The vehicle file
is displayed
The Firmware
is displayed
18
The Fuel type
is displayed
The following functions can be accessed from the “MAIN MENU”:
VEHICLE CONFIGURATION
This menu is used to display the configuration data of the vehicle, saved in the Sequential
control unit.
DISPLAY
By selecting this menu you can display the main signals of the vehicle in real time: Engine
rpm signal / petrol injection timing / Gas injection timing / Lambda probe signal / regulator
temperature / regulator pressure / battery voltage / type of fuel.
DIAGNOSIS
Each time an operational anomaly occurs in the Sequential system it can be displayed and
reset in this menu.
Service every 350 hours. Each time the system is serviced the installer must reset the
meter.
AUTO-CALIBRATION
This menu is used to calibrate the system with the vehicle stopped and the engine running
in neutral between 2500 and 3100 rpm.
MENU Save configuration / Load configuration
This menu is used to manage all the programming maps of the Sequential ECU’s.
ECU RE-PROGRAMMING
This menu is used if the ECU needs to be re-programmed following an up-date of the
“Firmware” on behalf of TartariniAuto.
19
VEHICLE CONFIGURATION
By selecting the “VEHICLE CONFIGURATION” menu you can display the main functions
used to optimise the running conditions of the vehicle on gas.
CHANGE-OVER
This page shows all the types of
settings to be made.
The items enhanced in YELLOW
are to be modified with KEY OFF
Type of fuel.
This selection is to be made to
initialise the control unit for the
correct operation according to the
type of fuel selected, LPG/CNG.
Type of injection.
Check the following to establish
the correct type of injection
system to be selected:
1) Petrol injection timing at
6000 rpm = 20 ms, select
Sequential.
Petrol injection timing at 6000
rpm = 10 ms, select Full-group
20
Type of injector RAIL.
Here you can select the right type
of injector RAIL to be used, by
choosing between MATRIX or
TARTARINI RAIL.
Displacement (cc).
This selection is used to set the
vehicle’s displacement.
Type of Revolution signal.
The WEAK signal is selected if the
rpm input is given through the pilot
signal of the transistor of the ignition
coils. The STANDARD option is
used in the case of connection to
the coil negative pole.
If the connection is made to the rpm
meter you can use either one of the
items, even if it is preferable to set
WEAK SIGNAL.
21
Number of cylinders.
This option is used merely to
inform the control unit of how
many cylinders the vehicle has
and therefore how many injectors
it has to read and pilot.
Type of ignition.
This function is used by the control unit
to calculate the engine rpm correctly.
Select SINGLE COIL if the vehicle has
one coil for each cylinder and the
signal is taken from the negative pole
of the coil. Select DOUBLE-COIL if the
vehicle has one coil that pilots two
cylinders and the signal is taken from
the negative pole of the coil. Use RPM
Sensor in the other cases. With some
5, 6 or 8 cylinder cars could be needed
the RPM Sensor 2
Type of change-over.
“In acceleration / In deceleration
This option is used to choose the
type of petrol – gas change-over:
In acceleration: the system
changes over when the engine
exceeds the RPM THRESHOLD set
for the change-over at + 100 rpm
(hysteresis):
If set in deceleration the system
changes over when the RPM falls
below this reference value.
22
Rpm threshold for change-over.
This points out the minimum rpm
threshold at which the system can
change over from petrol to Gas
(0;3000).
Regulator temperature for
change over.
This points out the minimum
temperature threshold at which
the system can change over from
petrol to Gas. The default and
suggested value is 35°C
Petrol gas switching delay
It indicates the number of seconds
that you can delay or anticipate
the petrol gas switching function.
The default and the suggested
setting is 30s.
23
LAMBDA
Type of Lambda probe.
This selection enables the control
unit to interpret the correct signal
sent from the Lambda probe.
It is advised to always connect the
lambda probe.
Number of lambda probe.
It is referred to probes before the
catalyst.
Cars with one lambda probe
only:
By selecting “1” you can read data
about one single probe.
Cars with 2 lambda probes:
By selecting “2” the system
supplies data about both probes
(connected via PURPLE and
PURPLE/BLACK cables.
2ns bank corrector
This function allows you to
balance the calibration of two
engine banks. Should the value of
the 2nd lambda probe be too rich
or too poor you can correct the
2nd engine bank by increasing or
decreasing the set values.
24
GAS LEVEL
Type of GAS level sensor.
This function is used to set the
correct level sensor fitted in the
vehicle. Setting “A E B” is to be
selected for most sensors.
Setting “ 0 – 90 ohm “ is to be set
for sensors with 0 – 90 ohm
specifications.
“0 – 90 ohm” sensors are
adjustable.
0 – 90 ohm modified:
We have the possibility to adjust
the resistance relative to the LED
of the switch.
We can therefore decide with how
much GAS the red reserve LED
and the other green LED’s are to
light up.
When doing so, you need to
adjust by 20 points per attempt.
PRESSURE
Type of pressure sensor
You can choose according to the
pressure meter installaed on the
car:
Differential sensor (1st version)
You only see the Gas pressure
inside regulator
Absolut sensor (2nd version)
Together with the gas pressure of
the regulator you can also see the
manifold pressure.
25
MAP
Map.
The map is constructed based on the
engine rpm and the petrol injection
timing.
This page enables you to optimise
the gas-values of the map coefficients
acquired during auto-calibration both
at minimum and out-of-minimum.
To modify the values, simply enhance
one or more cells, press the ENTER
key and the following page will
appear with the three different ways
of making the corrections:
1) Absolute
2) Linear
3)Percentage
DEFAULT: Linear
Absolute mode
The
value
writte
OVERWRITTEN
Example 110 + 10 → 10
will
be
Linear Mode
The value will be ADDED in the cell:
Example 110 + 10 → 120
26
Percentage Mode
The value is applied in PERCENT:
Example 110 + 10 → 121
Click on “Switching from PC”:
You will see another button
denominated “Switch” to the
right; this will allow you to
control the switch directly from
the computer.
When testing the calibration
settings on the road, simply
click on the switch button for
the vehicle to switch from
petrol to gas or from gas to
petrol.
When you have completed the
test, click on “End switching
from PC”.
Click on: “Modify map
references”:
You will see the page where
you can modify the engine
rpm references in the column
on the left and modify the
injection timing reference in
the column on the right.
Tartarini Auto does not
advise you to modify the
basic settings.
27
RICHER MIX
Extra-injection sensitivity
When driving the vehicle at a
constant speed you may feel
some jerking every now and
again. Check the movement of
the “little ball” in the map when the
jerking occurs. If it jumps
vertically, use the slider, clicking
on positive/negative until the
defect is eliminated.
CNG: very rarely used
Mixer rich in acceleration.
When accelerating strongly, if the
injection timing should vary with
very high injection time, the
engine would flood, causing an
incorrect input of power. In this
case, use the slider, clicking on
the negative sign until the defect
is eliminated.
LPG: very rarely used
28
ADAPTATION
Adaptation:
The purpose of adaptation is:
1) to compensate differences
in LPG/ CNG mixture
according to the various
Countries.
2) To compensate
progressive degradation of
components.
3) To avoid that “check
engine” lamp lights on.
Adaptation can be acitvated
after auto-calibration at
minimum.
Adaptation turned on= 0%
Adattatività turned off = OFF
In order to keep the adaptation performances at the best
level and always under control, you can take following
actions:
Final adjustment of petrol controls
1) In case, during the periodical checks gas controls might
exceed 10% either positive or negative, move the cursor of the
value shown near the adaptive function.
2) Reset adaptation.
ATTENTION:
if the adaptation function is active, no autocalibration and no
changes in the map carburation values are possible.
In order to make any changes, the adaptation function has to be
disconnected.
29
Reset adaptation:
By resetting the adaptation
function, all corrections in process
are void while the previous map
before starting adaptation is reenabled.
MODIFY CARBURATION
Modify fuel setting.
This page is used to finely tune the gas
values of the map coefficients (+-60
points) both at idle and out of idle,
acquired during the calibration
procedure.
IMPORTANT:
Using a “Tester” connected to the OBD
connector, check the fast/ slow
trimmers both at minimum and when
driving on the road.
When working in Closed Loop, these
trimmers must be as near as possible
to 0.
When checking under power with the
system in Open Loop, make the fuel
mix leaner by enhancing the cells
touched by the ball until the lambda
probe value is lean, then increase all
the cells enhanced by 5 “points”.
30
Weaker mix in Mazda type
strategy.
During a maximum request for input
power when the accelerator is
pressed right down, you may
encounter some jerking due to extrainjection inputs, which can be seen by
checking the “little ball” in the map. If
it continuously jumps vertically,
decrease the value until the defect is
eliminated.
Make sure the mix of gas is not too
weak in open-loop.
LPG: rarely used.
VIEW
Select VIEW from the main menu
and press ENTER.
This menu is used to view the
operating parameters.
Tthis page is used to view some values
measured by the controller, the
operating mode and the injection timing
(gas or petrol).
To ensure correct operation, it is
IMPORTANT that:
Engine rpm: the reading is real
Gas inj.T: at minimum, no lower than:
Matrix injectors: 3 ms
Tartarini injectors: 4 ms
Petrol inj.T/ Reg.T/ Gas T:
They must be legible
Regulator diff. Pressure: 1 bar
Suction man. Pressure:
0,4 bar at minimum
Battery voltage: 13/14 volt
Lambda probe: it must work in similar
conditions, both on petrol and gas, both
at minimum and when driving on the
road.
31
The operating parameters can be adjusted when testing on the road by means of the
acquisition function.
Configuration menu, VIEW.
Click on ACQUISITIONS.
At this stage you are ready to
start acquiring.
If the driving conditions are not
satisfactory, click on Start
saving.
You can also press Ctrl+F5
simultaneously, directly from
the View menu.
Acquisitions will appear with
a green ring to point out that
the system is acquiring all
the parameters.
Click on “Acquisitions” when
you wish to suspend the
procedure.
32
End “Saving”, or press Ctrl+F6
simultaneously, directly from
the View menu.
Name the file suitably and click on
“Save”.
To view the graph, click on
“Acquisitions, View Graph,
enhance the vehicle, then Open”
You can also view the graphs by
pressing Ctrl+F8 simultaneously,
directly from the View menu.
The graph of the test just carried
out will appear.
You can analyse many parameters
simultaneously by looking carefully
at the graph.
33
DIAGNOSIS
Select DIAGNOSIS from the main
manu and press ENTER.
If there are no errors in the controller,
the page appears as illustrated.
If on the other hand an error is
detected, the type of error will be
indicated with the possibility to cancel it
using the reset errors button.
Service:
Each time the system is serviced, the
installer must reset it using the “reset
service km” button.
Number of starting attempts directly
on gas:
The system allows you to start five
times directly on gas, exclusively in the
case of emergency.
All the service parameters will be
saved in the ecu.
AUTO-CALIBRATION
Select AUTO-CALIBRATION from
the main manu and press enter.
34
Check all the signals before you
press the ENTER key on the PC:
Rpm/ Gas inj. T/ Diff.Press./
Man.press./ Lambda/ Reg.T/ Gas T,
which must be all legible.
Important: the system cannot
calibrate until the regulator reaches a
temperature of 50°.
Press the ENTER button with the
switch unit turned to petrol and with
the engine running at minimum in
neutral gear.
It is very important not to accelerate
during the auto-calibration procedure
or not to do anything that is not
requested by the system.
The system will request you to leave
the engine running at minimum with
all the vehicle’s accessories switched
off.
As soon as you are ready, press
ENTER.
Wait for the system to complete the
self-learning phase.
35
Leave the engine running at minimum
without accelerating, turn the lights
and the demister on and wait a few
seconds before pressing ENTER.
ATTENTION:
Do not turn the heating/ air
conditioning on.
Wait for the system to complete the
self-learning phase again.
Leave the engine running at minimum
without acceleratine, turn the lights
and the demister off and wait a few
seconds before pressing ENTER.
36
Calibration completed successfully.
Check the sizing indicator of the
nozzles.
The nozzle sizing is correct when the
indicator is within the green bar.
SAVE CONFIGURATION
This sub-menu is used to save the
configuration parameters of the
control unit in a file that can later
be used to initialise other control
units fitted in vehicles of the same
or similar models.
The information entered in the
“File identification data” box is
used to add useful information for
characterising the vehicle on
which the system is installed.
Before you click on OK, choose
the configuration of the vehicle 3-4
cyl./ 5-6-8 cyl. or Turbo.
Each option has its own folder
with relative files saved.
37
LOAD CONFIGURATION
If you wish to load a file saved
previously, select “LOAD
CONFIGURATION” from the main
menu and press Enter.
This sub-page is used to load
configurations saved previously for
vehicles of the same model on which
the system is being installed.
Choose configuration 3-4 cyl./ 5-6-8
cyl./ or turbo
Enhance the name of the vehicle
involved and press ENTER. The file
selected will be automatically loaded
in the GAS ECU.
RE-PROGRAM THE ECU
Select RE-PROGRAM ECU from
the main menu and press Enter.
This menu is used if you should
need to re-program the control
unit following an up-date of the
“Firmware” on behalf of Tartarini
Auto, for improvement purposes
or to add new program functions.
38
Please perform the following
procedure in order to benefit of all
advantages of new Firmwares:
Click on “start from ground
parameters”: this takes the ECU
back to orignal settings.
At the end of this procedures:
-reset type of fuel
-reset type of ignition
-reset type of RPM signal
Now you can re-program the ECU
with the new firmware. All this
operation always with engine off.
To be able to program, select the
file containing the new “Firmware”
for the control unit, through a
communication window.
Once you have selected the file,
simply click on the Program tab to
start up-dating the control unit.
WARNING!:
NEVER re-programme the ECU while the vehicle is running on GAS.
39
TROUBLESHOOTING:
After 10 sec. from engine start the switch lights go off:
There is no RPM signal.
The engine runs on “3 cylinder” on gas:
The petrol injectors wiring harness might have been installed incorrectly. Letter “A” of the
injector rail MUST be corresponding to the BLUE and BLUE/BLACK wire of the cut-off
injector harness. Once the non-functioning injector hase been found out, check as follows:
1) make sure the rubber gas hose is not obstructed/ choked or is not leaking.
2) make sure the fitting on the suction manifold is not obstructed.
3) make sure the gauged fitting on the injector unit has the same diameter as the others
4) make sure the gas ECU sends the correct signal to that of the injector
5) make sure the commanding wires of the gas injectors are not damaged or disconnected
from the connector of the gas ECU or the connector of the injector unit.
As soon as switched to gas the car switches on petrol automatically and the
switch is still in the gas operation position:
1) The gas injection duration is too high
2) Check the gas phase filter
3) The injection pressure is too low.
If the “non compatible injector” warning occurs:
The PC has been disconnected from the serial cable with the program open, therefore exit
the program, re-connect the serial cable and connect again.
The RPM displayed are not correct:
1) Check if the type of ignition is set correctly (monocoil/ bicoil/ speed indicator)
2) Check if the type of rpm signal is set correctly (standard/ weak)
On gas the engine stalls:
1) Check if the level sensor is working properly (is there gas in the tank?).
2) If fuel is delivered to the rail.
3) If the 12V DC is supplied correctly.
The check engine light comes on:
1) Record the error in the petrol ECU (code, RPM, load...)
2) Check, by means of the OBD connector in “diagnosis”, if the petrol slow/fast trimmers
have drifted, in which case:
- clean the injector unit
- correct when running on gas until the petrol trimmers settle around zero or similar
values to when running on petrol.
3) Check if the Lambda probe is working.
4) If there is a Timing Advance Processor for the gas, try disconnecting it.
40
ERROR CODES
Communication errors
C01
C02/C03
The ECU is not responding: ckeck the connection, the power supply of
the ECU and the efficiency of the communication interface
The ECU is not working properly. Replace it.
Hardware key errors
H01
H02
H03/H04
The Hardware key is damaged or missed: check the key connection or
replace it.
The hardware key does not work: check the key connection or replace it.
Hardware key expired or with expiry date programmed incorrectly:
request Tartarini Auto for the hardware key up-date.
Re Programming errors
P01
The ECU does not dialogue: check the connection, check the ECU
power supply
P02
The ECU is not working properly. Replace it.
P03
Problem in reading the programming file: check the access rights to the
folder in which such file is stored, check its presence and/ or integrity
P04
Internet Explorer version obsolete: update it to version 6.0 or higher
P05/ P06/ P07/ Reprogramming error. Disconnect the power supply and try again in less
P08/ P09
than 4 seconds
P10 / P11
Programming file incoherent/ damaged: request Tartarini Auto for the
original programming file.
P12/ P13/ P14 System error. Contact Tartarini Auto explaining what is the hardware
configuration (PC, Windows version etc…..)
P15
The re programming file used is not compatible with the actual ECU. For
example the file used is for a 4 cylinder ECU while the ECU is for a 6
cylinder.
Load the programming file corresponding to the installed ECU type.
P1000...
Reprogramming error. Disconnect the power supply and try again in less
than 4 seconds
41
MAINTENANCE SCHEDULE
Mileage km
20.000
40.000
60.000
80.000
100.000
120.000
140.000
Type of
Maintenance
A
B
A
B
A
B
A
“A” Type Maintenance LPG/CNG
TOPIC
Check injection pressure set and rubber
hose
Check the Map and the general vehicle
driveability
Check the fixing of the tank
Visual inspection of water pipes, gas pipes
Check and/or do the maintenance
procedure of the injector rail.
Replace gas phase filter
TIME NEEDED
15 Minutes
30 Minutes
15 Minutes
15 Minutes + material if needed
60 Minutes + material if needed
15 Minutes + material if needed
“B” Type Maintenance LPG/CNG
TOPIC
Check injection pressure set and rubber
hose
Check the Map and the general vehicle
driveability
Visual inspection of water pipes, gas pipes
Check and/or do the maintenance
procedure of the pressure regulator
Check and/or do the maintenance
procedure of the injector rail.
Replace gas phase filter
TIME NEEDED
15 Minutes
30 Minutes
15 Minutes + material if needed
60 Minutes + material if needed
60 Minutes + material if needed
15 Minutes + material if needed
42
">