advertisement
![Samsung 2033SW User manual User manual | Manualzz Samsung 2033SW User manual User manual | Manualzz](http://s1.manualzz.com/store/data/002360682_1-33d0e0a2c16abcb602292861018f943d-360x466.png)
LCD Monitor
User Manual
Safety Instructions
Notational
Note
These safety instructions must be followed to ensure your safety and prevent property damage.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Otherwise, it may result in death or personal injury.
Otherwise, it may result in personal injury or property damage.
Notational Conventions
Prohibited
Do not disassemble
Do not touch
Important to read and understand at all times
Disconnect the plug from the outlet
Ground to prevent an electric shock
Power
When not used for extended period of time, set your computer to DPM.
If using screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases (or countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or loose power outlet.
• Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or plugging the plug into the outlet.
• Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power outlet.
• Otherwise, it may result in electric shock or personal injury.
1
Safety Instructions
Ensure that the power plug is plugged into the power outlet firmly and correctly.
• Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place any heavy material on it.
• Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
• Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the monitor.
• Otherwise, this may result in damage to the product due to electric shock.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.
• This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use the provided power cord of another product.
• Otherwise, this may result in fire or electric shock.
Installation
Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.
Failure to do so may cause serious damage to your monitor.
Do not drop the monitor when moving it.
• This may cause damage to the product or the person carrying it.
When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out.
• Otherwise, it may fall or cause personal injury.
• Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES,MOSQUITO REPELLANT,CIGA-
RETTES AND ANY HEATING APPLIANCES NEAR THE PROD-
UCT.
• Otherwise, this may cause fire.
2
Clean
Safety Instructions
Keep heating appliances as far away from the power cord or the product as possible.
• Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase or closet.
• Otherwise, this may result in fire due to an increase in the internal temperature.
Put down the monitor carefully.
• Failing to do so may damage the monitor.
Do not place the front of the product on the floor.
• Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall mount.
• Otherwise, it may fall and cause personal injury.
• Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that there is a clearance of more than 10 cm from the wall.
• Otherwise, it may result in fire due to an increase in the internal temperature.
Ensure that the packaging vinyl is kept away from children.
• Otherwise, it may result in serious harm (suffocation) if children play with it.
If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.
• This may cause damage to the product or the person carrying it.
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product.
• Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only. If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10.
3
Others
Safety Instructions
When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth.
• Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power cord.
• Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and clean it softly with a dry cloth.
• (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the product.
Since the product housing is easily scratched, make sure to use the specified cloth only.
• Use the specified cloth adding only a little water. As the product may be scratched if there is any foreign material on the cloth, make sure to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the main body of the product.
• Ensure that water does not enter the product and that it is not wet.
• Otherwise, this may result in electric shock, fire or a malfunction.
The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves.
• Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service
Center.
• Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car.
• Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center.
• Otherwise, this may result in electric shock or fire.
4
Safety Instructions
If thunder or lightening is occurring, do not touch the power cord or antenna cable.
• Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable.
• Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.
• Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or curtain.
• Otherwise, it may result in fire due to an increase in the internal temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
• If water or a foreign material enters the product, disconnect the power cord and contact a Service Center.
• This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material near the product.
• Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc).
• If water or foreign material enters the product, disconnect the power cord and contact a Service Center.
• Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may occur.
• If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
• Otherwise, your eyesight may be damaged.
Keep the volume at a comfortable level when using the headphones.
• Excessively loud volume level may damage hearing.
5
Safety Instructions
If you continually move closer to the product screen, your eyesight may be failing.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
• Otherwise, it may fall and cause personal injury and/or damage the product.
• If you use the product in a location exposed to vibrations, it may damage the product and result in fire.
When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product.
• Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the product.
• The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the power cord from the power outlet.
• Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product.
• Your children may hang onto the product causing it to fall and this may result in personal injury or death.
Do not turn the product upside down or move it while holding only the stand.
• Otherwise, it may fall and result in personal injury and/or damage to the product.
Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.
• This may reduce the lifetime of the product, and may result in fire.
Do not drop any objects onto the product or cause any impact to the product.
• Otherwise, this may result in electric shock or fire.
6
Safety Instructions
Do not use a humidifier or kitchen table near the product.
• Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power plug but ventilate immediately.
• If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display panel becomes hot. Do not touch it.
• Keep the small accessories in a location out of the reach of children.
Be careful when adjusting the angle of the product or the height of the stand.
• This may result in personal injury as your hand or fingers may become caught.
• Also, if you tilt the product too far, it may fall and cause personal injury.
Do not install the product in a location low enough for children to reach.
• Otherwise, it may fall and result in personal injury.
• Since the front part of the product is heavy, install the product on a level and stable surface.
Do not put any heavy objects on the product.
• This may result in personal injury and/or damage to the product.
Good Postures When Using the Monitor
When using the product, use it in the correct position.
• Keep your back straight while looking at the product.
• The distance between your eyes and the screen should be between 45 to 50 cm. Look at the screen from a slightly higher location than the height of the screen.
• When using the product, use it in the correct position.
• Adjust the angle so that light is not reflected on the screen.
• Place your arms perpendicular to your sides and allow your arms to be level with the back of the hand.
• Keep your elbow at 90 degrees.
• Keep your knees at greater than 90 degrees, and keep your heels firmly on the floor. Keep your arms lower than your heart.
7
Introduction
Package Contents
Note
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Monitor
Manuals
Quick Setup Guide Warranty Card
(Not available in all locations)
Cables
User's Guide
Others
D-Sub Cable Power Cord DVI Cable (option)
Cleaning Cloth(Option) Cable holding ring
8
Introduction
Note
Cleaning Cloth is only provided for highly polished black products as a product feature.
Your Monitor
Initial Settings
Front
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count.
Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
MENU button [MENU/ ]
Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.
Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness.
Customized Key[ ]
9
Introduction
You can customize key assignment for the Custom button according to your preferences.
Note
You can configure the customized key for a required function via Setup > Cus-
tomized Key.
Adjust buttons [ ]
These buttons allow you to adjust items in the menu.
Enter button [ ]
Activates a highlighted menu item.
Push the ' ', then selects the video signal while the OSD is off. (When the ' ' button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.)
Note
• If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.
• This function is not available for products with an Analog interface only.
AUTO button
Usethis button for auto adjustment.
(Available in Analog mode only)
Power button [ ]
Use this button for turning the product on and off.
Power Indicator
This light is lit when operating normally, and blinks once when your adjustments are saved.
Note
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods.
Rear
Note
The configuration at the back of the monitor may vary from product to product.
POWER port
10
Introduction
POWER port
Connect the power cord for your monitor to the
POWER port on the back of the product.
DVI IN
RGB IN
DVI IN
Connect the DVI Cable to the DVI IN port on the back of your monitor.
Note
Applicable to the digital (DVI)-dedicated models only.
RGB IN
Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor.
Kensington Lock
Kensington Lock
The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it.
Note
The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1.
Insert the locking device into the Kensington slot on the Monitor and turn it in the locking direction .
11
Introduction
2.
Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a heavy stationary object.
Note
See Connecting Cables for further information regarding cable connections.
Cable holding ring
• Fix the cables using the holding ring, as shown in the figure.
12
Connections
Connecting Cables
Use a connection appropriate for your computer.
Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the DVI IN Port on the back of your Monitor.
13
Connections
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Note
If the monitor and the computer are connected, you can turn them on and use them.
Using the Stand
Folding the base
Note
You can tilt the monitor upwards at an angle of -1° to 16°. ( ±1.0°)
Attaching a Base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Note
The VESA dimensions given above are an example. The VESA dimensions may differ depending on the product.
14
Connections
A. Monitor
B. Mounting interface pad (Sold separately)
1.
Turn off your monitor and unplug its power cord.
2.
Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3.
Remove the stand from the LCD monitor.
4.
Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
• Do not use screws longer than the standard dimension, as they may damage the inside of the Monitor.
• For wall mounts that do not comply with VESA standard screw specifications, the length of the screws may differ depending on their specifications.
• Do not use screws that do not comply with the VESA standard screw specifications.
Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
• To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface.
• Contact the nearest Samsung Service Center for more information. Samsung
Electronics will not be responsible for damages caused by using a base other than those specified.
• Please use Wall Mount according to the International standards.
15
Using the Software
Monitor Driver
Note
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
Prepare a blank disk and download the driver program file at the Internet web site shown here.
Internet web site : http://www.samsung.com/ (Worldwide)
Installing the Monitor Driver (Automatic)
1.
Insert CD into the CD-ROM drive.
2.
Click "Windows".
3.
Choose your monitor model in the model list, then click the "OK" button.
4.
If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button (Microsoft ® Windows ® XP/2000 Operating System).
16
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual)
Microsoft
®
Windows Vista™‚ Operating System
1.
Insert your Manual CD into your CD-ROM drive.
2.
Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
3.
Click "Personalization" and then "Display Settings".
4.
Click "Advanced Settings...".
5.
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is.
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
17
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6.
Click "Update Driver..." in the "Driver" tab.
7.
Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
8.
Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
18
Using the Software
9.
Select the model that matches your monitor from the list of monitor models on the screen, and click "Next".
10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Microsoft
®
Windows
®
XP Operating System
19
Using the Software
1.
Insert CD into the CD-ROM drive.
2.
Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
3.
Click "Display" icon and choose the "Settings" tab then click "Advanced...".
4.
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5.
Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
6.
Select "Don't search, I will..." then click "Next" and then click "Have disk".
20
Using the Software
7.
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8.
If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button.
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9.
Click the "Close" button then click "OK" button continually.
21
Using the Software
10. Monitor driver installation is completed.
Microsoft ® Windows ® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1.
Choose "OK" button on the "Insert disk" window.
2.
Click the "Browse" button on the "File Needed" window.
3.
Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1.
Click "Start", "Setting", "Control Panel".
2.
Double click the "Display" icon.
3.
Select the "Settings" tab and click "Advanced Properties" button.
4.
Choose "Monitor".
Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation
Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually.
5.
Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
6.
Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk".
7.
Click the "Browse" button then choose A:(D:\Driver).
8.
Click the "Open" button, then click "OK" button.
9.
Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button.
Microsoft ® Windows ® Millennium Operating System
1.
Click "Start", "Setting", "Control Panel".
2.
Double click the "Display" icon.
3.
Select the "Settings" tab and click "Advanced Properties" button.
22
Using the Software
4.
Select the "Monitor" tab.
5.
Click the "Change" button in the "Monitor Type" area.
6.
Choose "Specify the location of the driver".
7.
Choose "Display a list of all the driver in a specific location..." then click "Next" button.
8.
Click the "Have Disk" button.
9.
Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft ® Windows ® NT Operating System
1.
Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
2.
In Display Registration Information window, click Settings Tab and then click "All Display
Modes".
3.
Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK".
4.
Click "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1.
Press "Enter" at the first and the second screen after executing the X86Config file.
2.
The third screen is for setting your mouse.
3.
Set a mouse for your computer.
4.
The next screen is for selecting a keyboard.
5.
Set a Keyboard for your computer.
6.
The next screen is for setting your monitor.
7.
First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
8.
Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9.
Enter the model name of your monitor. This information will not affect the actual execution of
X-Window.
10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware.
23
Using the Software
Natural Color
Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI). This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images. For more information, refer to Help (F1) in the software program.
The Natural Color is provided online. You can download it from the website below and install; http://www.samsung.com/us/consumer/learningresources/monitor/naturalcolorexpert/pop_download.html
MagicTune™
Installation
1.
Insert the installation CD into the CD-ROM drive.
2.
Click the MagicTune™ installation file.
Note
If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MagicTune executable file on the CD.
3.
Select installation Language, Click "Next".
4.
When the Installation Shield Wizard window appears, click "Next".
5.
Select "I agree to the terms of the license agreement" to accept the terms of use.
6.
Choose a folder to install the MagicTune™ program.
7.
Click "Install".
8.
The "Installation Status" window appears.
9.
Click "Finish".
24
Using the Software
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.
Double-click the icon to start the program.
MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.
Installation Problems
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment.
System Requirements
OS
• Windows 2000
• Windows XP Home Edition
• Windows XP Professional
• Windows Vista™
It is recommended using MagicTune™ in Windows ® 2000 or later.
Hardware
• 32 MB Memory above
• 60 MB Hard disk space above
For more information, visit the MagicTune™ website.
Uninstall
The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows ® Control Panel.
Perform the following steps remove MagicTune™.
1.
Go to [Task Tray] → [Start] → [Settings] and select [Control Panel] in the menu. If the program runs on Windows ® XP, go to [Control Panel] in the [Start] menu.
2.
Click the "Add or Remove Programs" icon in Control Panel.
3.
In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to highlight it.
4.
Click the "Change/Remove" button to remove the program.
5.
Click "Yes" to begin the uninstall process.
6.
Wait until the "Uninstall Complete" dialog box appears.
Note
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.
25
Using the Software
MultiScreen
Note
The software may not be supported depending on the model.
Installation
1.
Insert the installation CD into the CD-ROM drive.
2.
Click the MultiScreen installation file.
Note
If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MultiScreen executable file on the CD.
3.
When the Installation Shield Wizard window appears, click "Next".
4.
Select "I agree to the terms of the license agreement" to accept the terms of use.
5.
Choose a folder to install the MultiScreen‚ program.
6.
Click "Install".
7.
The "Installation Status" window appears.
8.
Click "Finish".
9.
When the installation is complete, the Multiscreen executable icon appears on your desktop.
Double-click the icon to start the program.
Multiscreen execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.
Installation Problems
The installation of MultiScreen can be affected by such factors as the video card, motherboard and the network environment.
26
Using the Software
System Requirements
OS
• Windows 2000
• Windows XP Home Edition
• Windows XP Professional
• Windows Vista™
It is recommended using MultiScreen in Windows ® 2000 or later.
Hardware
• 32 MB Memory above
• 60 MB Hard disk space above
Uninstall
The Multiscreen program can be removed only by using the "Add or Remove Programs" option of the
Windows ® Control Panel.
Perform the following steps remove Multiscreen.
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Select Multiscreen from the list and then click the "Add/Delete" button.
27
Adjusting the Monitor
Direct Functions
AUTO
When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine,
Coarse and Position are adjusted automatically.
(Available in Analog mode only, so “AUTO” icon of OSD is gray in Digital mode.)
If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy.
If you change resolution in the control panel, auto function will be executed automatically.
OSD Lock & Unlock
This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings.
Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment lock function.
Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment lock function.
When pressing the AUTO button after locking the OSD
When pressing the MENU button after locking the OSD
Note
Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust Customized Key
( ) using the Direct button.
Customized key
You can customize key assignment for the Custom button according to your preferences.
28
Adjusting the Monitor
To view the operating screen displayed when pressing the [ ] button after configuring the customized key for a function, click the name of each function.
(MagicBright - MagicColor - Color Effect - Image Size)
Note
You can configure the customized key for a required function via
Setup > Customized Key.
ImageSize : Supplied for the wide models only such as 16:9 or
16:10.
Brightness
When OSD is not on the screen, push the Brightness ( ) button to adjust brightness.
SOURCE
Selects the video signal while the OSD is off.
Note
Not applicable to analogue
(D-SUB)-or-digital (DVI)dedicated models.
OSD Function
Top Menus Sub Menus
PICTURE Brightness
Fine
COLOR Magic-
Color
Contrast
Red
Color Effect
Gamma
Sharpness Magic-
Bright
Green Blue
Coarse
Color Tone
29
Picture
Adjusting the Monitor
SIZE &
POSI-
TION
H-Position
SET-
UP&RE-
SET
Reset
INFOR-
MATION
Auto
Source
V-Position
Menu Transparency
PC/AV Mode
Image Size Menu H-Po-
Display
Time sition
Language Off Timer
On/Off
Customized
Key
Menu V-Position
Off Timer
Setting
Menu
Brightness
Contrast
Sharpness
MagicBright
Description
(Not available in MagicBright mode of Dynamic Contrast.)
You can use the on-screen menus to change the brightness according to personal preference.
The larger the number, the brighter the screen. The smaller the number, the darker the screen.
(Not available in MagicBright mode of Dynamic Contrast.)
You can use the on-screen menus to change the contrast according to personal preference.
The larger the number, the brighter the screen. The smaller the number, the darker the screen.
( Not available in MagicColor mode of Full and Intelligent. )
Changes the clearance of image.
The larger the number, the clearer the screen. The smaller the number, the less clear the screen.
( Not available in MagicColor mode of Full and Intelligent. )
Push the button to circle through available preconfigured modes.
MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Custom, Text, Internet, Game,
Sport, Movie and Dynamic Contrast. Each mode has its own pre-
30
Menu
Coarse
Fine
Adjusting the Monitor
Description configured brightness value. You can easily select one of seven settings by simply pressing Customized Key control button.
• Custom
Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness and contrast by using the
OSD menu.
• Text
For documentations or works involving heavy text.
• Internet
For working with a mixture of images such as texts and graphics.
• Game
For watching motion pictures such as a game.
• Sport
For watching motion pictures such as a sport.
• Movie
For watching motion pictures such as a DVD or Video CD.
• Dynamic Contrast
Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast.
Removes noise such as vertical stripes.
The larger the number, the more the screen increases vertically. The smaller the number, the more the screen decreases vertically.
Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.
(Available in Analog mode only)
Removes noise such as horizontal stripes.
If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).
(Available in Analog mode only)
31
Color
Adjusting the Monitor
Menu
MagicColor
Red
Green
Blue
Color Tone
Description
MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.
• Off - Returns to the original mode.
• Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left.
• Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
• Intelligent - Displays vivid natural color with clearness.
Adjusts individual Red color balance.
The larger the number, the closer it is to red.
( Not available in MagicColor mode of Full and Intelligent. )
Adjusts individual Green color balance.
The larger the number, the closer it is to green.
( Not available in MagicColor mode of Full and Intelligent. )
Adjusts individual Blue color balance.
The larger the number, the closer it is to blue.
( Not available in MagicColor mode of Full and Intelligent. )
The tone of the color can be changed and one of four modes can be selected.
( Not available in MagicColor mode of Full and Intelligent. )
• Cool - Makes whites bluish.
• Normal - Keeps whites white.
• Warm - Makes whites reddish.
• Custom - Select this mode when you want to adjust the image according to your preferences.
32
Adjusting the Monitor
Menu
Color Effect
Gamma
Description
You can change the overall mood by changing the screen colors.
( Not available in MagicColor mode of Full and Intelligent. )
• Off - This applies an achromatic color to the screen to adjust the screen effects.
• Grayscale - The default colors of black and white are displayed.
• Green - This applies the green color effect to a black and white screen.
• Aqua - This applies the aqua color effect to a black and white screen.
• Sepia - This applies the Sepia color effect to a black and white screen.
Gamma correction changes the luminance of the colors with intermediate luminance.
• Mode 1 : Sets the screen to the default brightness.
• Mode 2 : Sets the screen to bright.
• Mode 3 : Sets the screen to dim.
SIZE & POSITION
Menu
H-Position
V-Position
Description
Changes the horizontal position of the monitor's entire display.
You can move the position of the screen to the left and right by pressing the and buttons, respectively.
(Available in Analog mode only)
Note
When TV signal is input in AV mode ,select “Screen Fit “to adjust horizontal position in 0-6 levels.
Changes the vertical position of the monitor's entire display.
You can move the position of the screen downwards and upwards by pressing the and buttons, respectively.
33
Menu
Image Size
Adjusting the Monitor
Description
(Available in Analog mode only)
Note
When TV signal is input in AV mode ,select “Screen Fit “to adjust vertical position in 0-6 levels.
Note
Supplied for the wide models only such as 16:9 or 16:10.
You can change the size of the screen displayed on your monitor.
PC signals
• Auto - The screen is displayed in accordance with the screen aspect ratio of the input signals.
• Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals.
Note
• Signals not available in the standard mode table are not supported.
• If the wide screen which is the optimal resolution for the monitor is set on your PC, this function is not performed.
AV signals
• 4 : 3 - Sets the picture to 4:3 normal mode.
• 16 : 9- Sets the picture to 16:9 wide mode.
• Screen Fit- Use the function to see the full image without any cutoff when DVI (480p/576p/720p/1080i/1080p) signals are input.
Note
It can only be selected if an external input is connected to the DVI terminal and the 'PC/AV Mode' is set to 'AV'.
• 4 : 3 - Sets the picture to 4:3 normal mode.
• Wide-Sets the picture to 16:10 wide mode.
• Screen Fit- Use the function to see the full image without any cutoff when DVI (480p/576p/720p/1080i/1080p) signals are input.
Note
• It can only be selected if an external input is connected to the DVI terminal and the 'PC/AV Mode' is set to 'AV'.
• When the panel is of 16:10,the screen size options include
“4:3”,”wide “,”Screen fit“.
34
SETUP&RESET
Adjusting the Monitor
Menu
Reset
Description
Reverts the product settings to factory defaults.
• Yes
• No
Menu Transparency
Change the transparency of the background of the OSD.
• Off : The menus are displayed in the normal way (non-transparently).
Language
• On : The menus are displayed transparently.
You can select the language used to display the menus.
You can choose one of nine languages.
Note
The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
Off Timer On/
Off
You can enable or disable the Off Time function.
• Off
• On
Off Timer Setting The monitors will turn off automatically at the specified time.
Auto Source Select Auto Source for the monitor to automatically select the signal source.
• Auto
• Manual
Note
Not applicable to analogue (D-SUB)-or-digital (DVI)-dedicated models.
35
Adjusting the Monitor
Menu
PC/AV Mode
Display Time
Description
This function allows the screen to be displayed at the optimal quality in accordance with the size of the screen when a 480P, 576P, 720P,
1080i, or 1080P video signal is input in DVI mode.
Set to "PC" when connected to a PC, Set to "AV" when connected to an AV device.
If not set to "AV", the screen may not be displayed normally.
(Unavailable in Analog mode)
Note
Supplied for the wide models only such as 16:9 or 16:10.
The menu will be automatically turned off if no adjustments are made for a certain time period.
You can set the amount of time the menu will wait before it is turned off.
• 5 sec
• 10 sec
• 20 sec
• 200 sec
Customized Key You can specify a function which will be activated when the Custom-
ized Key ( )is pressed.
INFORMATION
Menu
INFORMA-
TION
Description
Shows a video source, display mode on the OSD screen.
Note
For models with an Analog interface only, “Analog/Digital“is not shown in the”Information”.
36
Troubleshooting
Self-Test Feature Check
Note
Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
Self-Test Feature Check
1.
Turn off both your computer and the monitor.
2.
Unplug the video cable from the back of the computer.
3.
Turn on the monitor.
If the monitor is functioning properly, you will see a box in the illustration below.
Note
For models with an Analog interface only, “Analog/Digital” is not shown in the Warning Message
OSD.
This box appears during normal operation if the video cable becomes disconnected or damaged.
4.
Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.
Note
For models with an Analog interface only, “Analog/Digita” is not shown in the Warning Message
OSD.
37
Troubleshooting
Environment
The location and the position of the monitor may influence the quality and other features of the monitor.
If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.
Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.
Useful Tips
A monitor recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the monitor to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode **** x ****
60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on.
If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition.
In this case, check the computer for trouble.
Check List
Note
Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
No images on the screen. I cannot turn on the monitor.
Q: Is the power cord connected properly?
A: Check the power cord connection and supply.
Q: Can you see "Check Signal Cable" on the screen?
A: (Connected using the D-sub cable)
Check the signal cable connection.
(Connected using the DVI cable)
If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog.
If you still see an (error) message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press ‘ ’ button to have the monitor double-check the input signal source.
Q: If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.
A: If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card.
38
Troubleshooting
(Refer to the Preset Timing Modes)
If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.
Q: Can you see "Not Optimum Mode", "Recommended Mode **** x **** 60 Hz" on the screen?
A: You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.
A: Adjust the maximum resolution and frequency that the monitor can handle properly.
A: If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode **** x **** 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode **** x **** 60 Hz" message appears for one minute and then disappears.
Please change to the recommended mode during this one-minute period.
(The message is displayed again if the system is rebooted.)
Q: There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals?
A: The monitor is in PowerSaver mode.
A: Press a key on the keyboard to activate the monitor and restore the image on the screen.
A: If there is still no image, press the ' ' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
Q: Connected using the DVI cable?
A: You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system.
I cannot see the On Screen Display.
Q: Have you locked the On Screen Display (OSD) Menu to prevent changes?
A: Unlock the OSD by pressing the [MENU/ ] button for at least 5 seconds.
The screen shows strange colors or just black and white.
Q: Is the screen displaying only one color as if looking at the screen through a cellophane paper?
A: Check the signal cable connection.
A: Make sure the video card is fully inserted in its slot.
Q: Have the screen colors become strange after running a program or due to a crash between applications?
A: Reboot the computer.
Q: Has the video card been set properly?
A: Set the video card by referring to the video card manual.
39
Troubleshooting
The screen suddenly has become unbalanced.
Q: Have you changed the video card or the driver?
A: Adjust screen image position and size using the OSD.
Q: Have you adjusted the resolution or frequency to the monitor?
A: Adjust the resolution and frequency at the video card.
(Refer to the Preset Timing Modes)
Q: The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD.
The screen is out of focus or OSD cannot be adjusted.
Q: Have you adjusted the resolution or frequency on the monitor?
A: Adjust the resolution and frequency of the video card.
(Refer to the Preset Timing Modes)
LED is blinking but no images on the screen.
Q: Is the frequency properly adjusted when checking the Display Timing on the menu?
A: Adjust the frequency properly by referring to the video card manual and the Preset Timing
Modes.
(The maximum frequency per resolution may differ from product to product.)
There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
Q: Have the Windows colors been set properly?
A: Windows XP :
Set the resolution at the Control Panel → Appearance and Themes → Display → Settings.
A: Windows ME/2000 :
Set the resolution at the Control Panel → Display → Settings.
Q: Has the video card been set properly?
A: Set the video card by referring to the video card manual.
There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found".
Q: Have you installed the monitor driver?
A: Install the monitor driver according to the Driver Installation Instructions.
Q: See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
A: Install the monitor driver according to the Driver Installation Instructions.
My computer is on and the LED is blinking. However, only a blank screen is displayed on the monitor.
Q: Check whether your computer is in hibernation mode (The monitor turns off).
40
Troubleshooting
A: Move your mouse or press any key to display the screen again.
Problems related to Audio.
Q: No sound.
A: Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and the audio-out port on your sound card.
(Refer to Connecting Cables).
Check the volume level.
Q: Sound level is too low.
A: Check the volume level.
If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program.
Check when MagicTune™ does not function properly.
Q: MagicTune™ feature is found only on PC (VGA) with Window OS that supports Plug and Play.
A: To check whether your PC is available for MagicTune™ feature, follow the steps below (When
Windows is XP);
Control Panel → Performance and Maintenance → System → Hardware → Device Manager
→ Monitors → After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware.
A: MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided.
http://www.samsung.com/monitor/magictune
MagicTune™ doesn't work properly.
Q: Have you changed your PC or video graphic card?
A: Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune
Q: Did you install the program?
A: Reboot the computer after installing the program for the first time. If a copy of the program is already installed, remove it, reboot the computer, and then install the program again. You need to reboot the computer for it to operate normally after installing or removing the program.
Note
Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.
Check the following items if there is trouble with the monitor.
Check if the power cord and the video cables are properly connected to the computer.
Check if the computer beeps more than 3 times when booting.
(If it does, request an a service for the main board of the computer.)
41
Troubleshooting
If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver.
Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz.
(Do not exceed 75 Hz when using the maximum resolution.)
If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter in the "Control Panel → System → Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.
Note
If problems repeatedly occur, contact an authorized service center.
Q & A
Q: How can I change the frequency?
A: The frequency can be changed by reconfiguring the video card.
A: Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)
Q: How can I adjusts the resolution?
A: Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.
A: Windows ME/2000:
Set the resolution in the Control Panel → Display → Settings.
* Contact the video card manufacturer for details.
Q: How can I set the Power Saving function?
A: Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
A: Windows ME/2000:
Set the resolution at the Control Panel → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
Q: How can I clean the outer case/LCD Panel?
A: Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water.
Do not leave any detergent or scratches on the case. Do not let any water enter the monitor.
42
Troubleshooting
Note
Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
43
Specifications
General
General
Model Name
LCD Panel
Size
Display area
SyncMaster 633NW
15.6 inch (39 cm)
344.232 mm(H) x 193.536 mm(V)
Pixel Pitch
Synchronization
Horizontal
0.252 mm(H) x 0.252 mm(V)
Vertical
Display Color
16.7 M
Resolution
Optimum resolution
30 ~ 61 kHz
56 ~ 75 Hz
1360 x 768@60 Hz
Maximum resolution
Input Signal, Terminated
1360 x 768@60 Hz
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
90 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable, 1500 +/- 20 mm
Dimensions (W x H x D) / Weight (Simple Stand)
386 x 264.5 x 67.2 mm (15.2 x 10.4 x 2.6 inch) (Without Stand)
386 x 315.8 x 186.6 mm (15.2 x 12.4 x 7.3 inch) (With Stand)/ 2.55 kg (5.62 lbs)
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 20 % ~ 80 %, non-condensing
Temperature : -4°F ~ 140°F (-20°C ~ 60°C)
Storage
Humidity : 10 % ~ 80 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
18 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
IBM, 640 x 350
IBM, 640 x 480
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1360 X 768
37.500
35.156
37.879
48.077
46.875
48.363
56.476
60.023
47.712
Horizontal
Frequency
(kHz)
31.469
31.469
31.469
35.000
49.726
37.861
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
70.086
59.940
70.087
66.667
74.551
72.809
75.000
56.250
60.317
72.188
25.175
25.175
28.322
30.240
57.284
31.500
31.500
36.000
40.000
50.000
+/-
-/-
-/+
-/-
-/-
-/-
-/-
+/+
+/+
+/+
75.000
60.004
70.069
75.029
49.500
65.000
75.000
78.750
+/+
-/-
-/-
+/+
60.015 85.500 +/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
LCD Panel
Size
Display area
SyncMaster 733A
17 inch (43 cm)
337.920 mm (H) x 270.336 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.264 mm (H) x 0.264 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
56 ~ 75 Hz
1280 x 1024@60 Hz
Maximum resolution
Input Signal, Terminated
1280 x 1024@75 Hz
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
380.6 x 349 x 72.3 mm / 15.0 x 13.7 x 2.8 inch (Without Stand)
380.6 x 397.1 x 200 mm / 15.0 x 15.6 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
30 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IBM,640 x 350
IBM,640 x 480
IBM,720 x 400
MAC,640 x 480
MAC,832 x 624
MAC,1152 x 870
VESA,640 x 480
VESA,640 x 480
VESA,800 x 600
VESA,800 x 600
VESA,800 x 600
VESA,800 x 600
VESA,1024 x 768
VESA,1024 x 768
VESA,1024 x 768
VESA,1152 x 864
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1280 X 800
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
31.469 70.086 25.175 +/-
31.469 59.940 25.175 -/-
31.469 70.087 28.322 -/+
35.000 66.667 30.240 -/-
49.726 74.551 57.284 -/-
68.681 75.062 100.000 -/-
37.861 72.809 31.500 -/-
37.500 75.000 31.500 -/-
35.156 56.250 36.000 +/+
37.879 60.317 40.000 +/+
48.077 72.188 50.000 +/+
46.875 75.000 49.500 +/+
48.363 60.004 65.000 -/-
56.476 70.069 75.000 -/-
60.023 75.029 78.750 +/+
67.500 75.000 108.000 +/+
60.000
63.981
60.000 108.000 +/+
60.020 108.000 +/+
79.976
49.702
75.025
59.810
135.000
83.500
+/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
LCD Panel
Size
Display area
SyncMaster 733A PLUS
17 inch (43 cm)
337.920 mm (H) x 270.336 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.264 mm (H) x 0.264 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
56 ~ 75 Hz
1280 x 1024@60 Hz
Maximum resolution
Input Signal, Terminated
1280 x 1024@75 Hz
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
380.6 x 349 x 72.3 mm / 15.0 x 13.7 x 2.8 inch (Without Stand)
380.6 x 397.1 x 200 mm / 15.0 x 15.6 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
30 watts Less than 1 watts
This monitor is EPA ENERGY STAR ® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR ® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM,640 x 350
IBM,640 x 480
IBM,720 x 400
MAC,640 x 480
MAC,832 x 624
MAC,1152 x 870
VESA,640 x 480
VESA,640 x 480
VESA,800 x 600
VESA,800 x 600
VESA,800 x 600
VESA,800 x 600
VESA,1024 x 768
VESA,1024 x 768
VESA,1024 x 768
VESA,1152 x 864
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1280 X 800
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
31.469 70.086 25.175 +/-
31.469 59.940 25.175 -/-
31.469 70.087 28.322 -/+
35.000 66.667 30.240 -/-
49.726 74.551 57.284 -/-
68.681 75.062 100.000 -/-
37.861 72.809 31.500 -/-
37.500 75.000 31.500 -/-
35.156 56.250 36.000 +/+
37.879 60.317 40.000 +/+
48.077 72.188 50.000 +/+
46.875 75.000 49.500 +/+
48.363 60.004 65.000 -/-
56.476 70.069 75.000 -/-
60.023 75.029 78.750 +/+
67.500 75.000 108.000 +/+
60.000
60.000 108.000 +/+
63.981
79.976
49.702
60.020
75.025
59.810
108.000
135.000
83.500
+/+
+/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
LCD Panel
Size
Display area
SyncMaster 733N
17 inch (43 cm)
337.920 mm (H) x 270.336 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.264 mm (H) x 0.264 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
56 ~ 75 Hz
1280 x 1024@60 Hz
Maximum resolution
Input Signal, Terminated
1280 x 1024@75 Hz
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
380.6 x 349 x 72.3 mm / 15.0 x 13.7 x 2.8 inch (Without Stand)
380.6 x 397.1 x 200 mm / 15.0 x 15.6 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
30 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IBM, 640 x 350
IBM, 640 x 480
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1280 x 800
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
56.476
Horizontal
Frequency
(kHz)
31.469
31.469
31.469
35.000
49.726
68.681
60.023
67.500
60.000
63.981
79.976
49.702
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
70.086
59.940
70.087
66.667
74.551
75.062
72.809
75.000
56.250
60.317
25.175
25.175
28.322
30.240
57.284
100.000
31.500
31.500
36.000
40.000
-/-
-/-
+/+
+/+
+/-
-/-
-/+
-/-
-/-
-/-
72.188
75.000
60.004
70.069
50.000
49.500
65.000
75.000
+/+
+/+
-/-
-/-
75.029
75.000
78.750
108.000
+/+
+/+
60.000 108.000 +/+
60.020 108.000 +/+
75.025
59.810
135.000 +/+
83.500 -/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
LCD Panel
Size
Display area
SyncMaster 733N PLUS
17 inch (43 cm)
337.920 mm (H) x 270.336 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.264 mm (H) x 0.264 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
56 ~ 75 Hz
1280 x 1024@60 Hz
Maximum resolution
Input Signal, Terminated
1280 x 1024@75 Hz
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
380.6 x 349 x 72.3 mm / 15.0 x 13.7 x 2.8 inch (Without Stand)
380.6 x 397.1 x 200 mm / 15.0 x 15.6 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
30 watts Less than 1 watts
This monitor is EPA ENERGY STAR ® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR ® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 640 x 350
IBM, 640 x 480
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1280 x 800
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.500
35.156
37.879
48.077
46.875
48.363
56.476
60.023
67.500
60.000
Horizontal
Frequency
(kHz)
31.469
31.469
31.469
35.000
49.726
68.681
37.861
63.981
79.976
49.702
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
56.250
60.317
72.188
75.000
60.004
70.069
75.029
75.000
70.086
59.940
70.087
66.667
74.551
75.062
72.809
75.000
25.175
25.175
28.322
30.240
57.284
100.000
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
108.000
+/-
-/-
-/+
-/-
-/-
-/-
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/-
+/+
+/+
60.000 108.000 +/+
60.020 108.000 +/+
75.025
59.810
135.000 +/+
83.500 -/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 733NW
17 inch (43 cm)
367.2 mm(H) x 229.5 mm(V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.2 M
Resolution
Optimum resolution
0.255 mm(H) x 0.255 mm(V)
30 ~ 81 kHz
56 ~ 75 Hz
1440 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1440 x 900@75 Hz
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
136.75 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable, 1500 +/- 20 mm
Dimensions (W x H x D) / Weight (Simple Stand)
410.9 x 302.5 x 64.5 mm (16.2 x 11.9 x 2.5 inch) (Without Stand)
410.9 x 351.2 x 187 mm (16.2 x 13.8 x 7.4 inch) (With Stand)/ 2.8 kg (6.17 lbs)
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 32 °F ~ 104°F (0°C ~ 40°C)
Operating
Humidity : 20 % ~ 80 %, non-condensing
Temperature : -4°F ~ 140°F (-20°C ~ 60°C)
General
Storage
Plug and Play Capability
Humidity : 10 % ~ 80 %, non-condensing
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
20 watts
Blinking
Less than 1 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 640 x 350
IBM, 640 x 480
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1280 x 800
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
68.681
37.861
37.500
35.156
37.879
48.077
46.875
Horizontal
Frequency
(kHz)
31.469
31.469
31.469
35.000
49.726
48.363
56.476
60.023
67.500
60.000
63.981
79.976
49.702
Vertical
Frequency (Hz)
75.062
72.809
75.000
56.250
60.317
72.188
75.000
70.086
59.940
70.087
66.667
74.551
Pixel Clock
(MHz)
25.175
25.175
28.322
30.240
57.284
100.000
31.500
31.500
36.000
40.000
50.000
49.500
Sync Polarity
(H/V)
-/-
-/-
-/-
+/+
+/+
+/+
+/+
+/-
-/-
-/+
-/-
-/-
60.004
70.069
75.029
75.000
65.000
75.000
78.750
108.000
-/-
-/-
+/+
+/+
60.000 108.000 +/+
60.020 108.000 +/+
75.025
59.810
135.000 +/+
83.500 -/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 933BW
19 inch (48 cm)
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2835 mm (H) x 0.2835 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1440 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1440 x 900@75 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 8.82 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
34 watts
Blinking
Less than 1 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1440 X 900
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
Vertical
Frequency (Hz)
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.087
66.667
74.551
75.062
59.940
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
Sync Polarity
(H/V)
56.476
60.023
67.500
49.702
60.000
63.981
79.976
55.935
70.635
70.069
75.029
75.000
59.810 83.500 +/+
60.000 108.000 +/+
60.020
75.025
59.887
74.984
75.000
78.750
108.000
108.000
135.000
106.500
136.750
-/-
+/+
+/+
+/+
+/+
-/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/+
-/-
-/-
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 933BW PLUS
19 inch (48 cm)
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2835 mm (H) x 0.2835 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1440 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1440 x 900@75 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 8.82 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
34 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1440 X 900
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
35.156
37.879
48.077
46.875
48.363
56.476
60.023
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
37.861
37.500
67.500
49.702
60.000
63.981
79.976
55.935
70.635
Vertical
Frequency (Hz)
56.250
60.317
72.188
75.000
60.004
70.069
75.029
70.087
66.667
74.551
75.062
59.940
72.809
75.000
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
Sync Polarity
(H/V)
+/+
+/+
+/+
+/+
-/-
-/-
+/+
-/-
-/-
-/-
-/-
-/+
-/-
-/-
75.000 108.000 +/+
59.810 83.500 +/+
60.000 108.000 +/+
60.020 108.000 +/+
75.025
59.887
74.984
135.000
106.500
136.750
+/+
-/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 933GW
19 inch (48 cm)
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2835 mm (H) x 0.2835 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1440 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1440 x 900@75 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 8.82 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
34 watts
Blinking
Less than 1 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1440 X 900
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
Vertical
Frequency (Hz)
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.087
66.667
74.551
75.062
59.940
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
Sync Polarity
(H/V)
56.476
60.023
67.500
49.702
60.000
63.981
79.976
55.935
70.635
70.069
75.029
75.000
59.810 83.500 +/+
60.000 108.000 +/+
60.020
75.025
59.887
74.984
75.000
78.750
108.000
108.000
135.000
106.500
136.750
-/-
+/+
+/+
+/+
+/+
-/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/+
-/-
-/-
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 933GW PLUS
19 inch (48 cm)
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2835 mm (H) x 0.2835 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1440 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1440 x 900@75 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 8.82 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
34 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1440 X 900
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
35.156
37.879
48.077
46.875
48.363
56.476
60.023
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
37.861
37.500
67.500
49.702
60.000
63.981
79.976
55.935
70.635
Vertical
Frequency (Hz)
56.250
60.317
72.188
75.000
60.004
70.069
75.029
70.087
66.667
74.551
75.062
59.940
72.809
75.000
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
Sync Polarity
(H/V)
+/+
+/+
+/+
+/+
-/-
-/-
+/+
-/-
-/-
-/-
-/-
-/+
-/-
-/-
75.000 108.000 +/+
59.810 83.500 +/+
60.000 108.000 +/+
60.020 108.000 +/+
75.025
59.887
74.984
135.000
106.500
136.750
+/+
-/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 933NW
19 inch (48 cm)
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2835 mm (H) x 0.2835 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1440 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1440 x 900@75 Hz
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 10.7 lbs
VESA Mounting Interface
75.0 mm x 75.0 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Storage
Plug and Play Capability
Humidity : 5 % ~ 95 %, non-condensing
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
ON
34 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1440 X 900
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
Vertical
Frequency (Hz)
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.087
66.667
74.551
75.062
59.940
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
Sync Polarity
(H/V)
56.476
60.023
67.500
49.702
60.000
63.981
79.976
55.935
70.635
70.069
75.029
75.000
59.810 83.500 +/+
60.000 108.000 +/+
60.020
75.025
59.887
74.984
75.000
78.750
108.000
108.000
135.000
106.500
136.750
-/-
+/+
+/+
+/+
+/+
-/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/+
-/-
-/-
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 933NWPLUS
19 inch (48 cm)
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2835 mm (H) x 0.2835 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1440 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1440 x 900@75 Hz
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 10.7 lbs
VESA Mounting Interface
75.0 mm x 75.0 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Storage
Plug and Play Capability
Humidity : 5 % ~ 95 %, non-condensing
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
ON
34 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1440 X 900
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
Vertical
Frequency (Hz)
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.087
66.667
74.551
75.062
59.940
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
Sync Polarity
(H/V)
56.476
60.023
67.500
49.702
60.000
63.981
79.976
55.935
70.635
70.069
75.029
75.000
59.810 83.500 +/+
60.000 108.000 +/+
60.020
75.025
59.887
74.984
75.000
78.750
108.000
108.000
135.000
106.500
136.750
-/-
+/+
+/+
+/+
+/+
-/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/+
-/-
-/-
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 933SN
18.5 inch (47 cm)
409.8 mm (H) x 230.4 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.3 mm (H) x 0.3 mm (V)
31 ~ 80 kHz
56 ~ 75 Hz
1360 x 768@60 Hz
Maximum resolution
Input Signal, Terminated
1360 x 768@60 Hz
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
89 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
453.3 x 299.3x 69.8 mm / 17.9 x 11.8x 2.8inch (Without Stand)
453.3 x 354.9 x 176.6 mm / 17.9 x13.9 x 6.9 inch (With Stand), 3.65 kg / 9.8 lbs
VESA Mounting Interface
75.0 mm x 75.0 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Storage
Plug and Play Capability
Humidity : 5 % ~ 95 %, non-condensing
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
ON
18 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1360 X 768
35.156
37.879
48.077
46.875
48.363
56.476
60.023
47.712
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
37.861
37.500
Vertical
Frequency (Hz)
70.087
66.667
74.551
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.069
75.029
60.000
Pixel Clock
(MHz)
28.322
30.240
57.284
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
85.500
Sync Polarity
(H/V)
-/+
-/-
-/-
-/-
-/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
+/+
+/+
+/+
+/+
-/-
-/-
+/+
+/+
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 933SN PLUS
18.5 inch (47 cm)
409.8 mm (H) x 230.4 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.3 mm (H) x 0.3 mm (V)
31 ~ 80 kHz
56 ~ 75 Hz
1360 x 768@60 Hz
Maximum resolution
Input Signal, Terminated
1360 x 768@60 Hz
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
89 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
453.3 x 299.3x 69.8 mm / 17.9 x 11.8x 2.8inch (Without Stand)
453.3 x 354.9 x 176.6 mm / 17.9 x13.9 x 6.9 inch (With Stand), 3.65 kg / 9.8 lbs
VESA Mounting Interface
75.0 mm x 75.0 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Storage
Plug and Play Capability
Humidity : 5 % ~ 95 %, non-condensing
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
ON
18 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1360 X 768
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
37.861
37.500
35.156
37.879
48.077
46.875
48.363
56.476
60.023
47.712
Vertical
Frequency (Hz)
70.087
66.667
74.551
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.069
75.029
60.000
Pixel Clock
(MHz)
28.322
30.240
57.284
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
85.500
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
+/+
+/+
-/-
-/-
+/+
+/+
-/-
-/-
+/+
+/+
-/+
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2033SN
20.0 inch (50 cm)
442.8 mm (H) x 249.075 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2768 mm (H) x 0.2768 mm (V)
30 ~ 81kHz
56 ~ 75 Hz
1600 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1600 x 900@60 Hz
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
150 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
485.8 x 325.9 x 72.6 mm(19.1 x 12.8 x 2.9 inch) (Without Stand)
485.8 x 373.5 x 200 mm (19.1 x 14.7 x 7.9 inch) (With Stand) / 4.45 kg(9.8 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Storage
Plug and Play Capability
Humidity : 5 % ~ 95 %, non-condensing
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
40 watts
Blinking
Less than 1 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERG Y2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 800
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1600 x 900
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
56.476
60.023
67.500
49.702
62.795
55.935
70.635
60.000
Vertical
Frequency (Hz)
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.087
66.667
74.551
75.062
59.940
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
Sync Polarity
(H/V)
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/+
-/-
-/-
-/-
-/-
70.069
75.029
75.000
78.750
-/-
+/+
75.000 108.000 +/+
59.810 83.50 -/+
74.934 106.500 -/+
59.887 106.500 -/+
74.984
60.000
136.750
108.000
-/+
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2033SN PLUS
20.0 inch (50 cm)
442.8 mm (H) x 249.075 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2768 mm (H) x 0.2768 mm (V)
30 ~ 81kHz
56 ~ 75 Hz
1600 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1600 x 900@60 Hz
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
150 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
485.8 x 325.9 x 72.6 mm(19.1 x 12.8 x 2.9 inch) (Without Stand)
485.8 x 373.5 x 200 mm (19.1 x 14.7 x 7.9 inch) (With Stand) / 4.45 kg(9.8 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Storage
Plug and Play Capability
Humidity : 5 % ~ 95 %, non-condensing
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
40 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERG Y2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 800
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1600 x 900
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
35.156
37.879
48.077
46.875
48.363
56.476
60.023
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
37.861
37.500
67.500
49.702
62.795
55.935
70.635
60.000
Vertical
Frequency (Hz)
56.250
60.317
72.188
75.000
60.004
70.069
75.029
70.087
66.667
74.551
75.062
59.940
72.809
75.000
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
Sync Polarity
(H/V)
+/+
+/+
+/+
+/+
-/-
-/-
+/+
-/-
-/-
-/-
-/-
-/+
-/-
-/-
75.000 108.000 +/+
59.810 83.50 -/+
74.934 106.500 -/+
59.887 106.500 -/+
74.984
60.000
136.750
108.000
-/+
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2033SW
20 inch (50 cm)
442.8 mm (H) x 249.075 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2768 mm (H) x 0.2768 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1600 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1600 x 900@60 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
150 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable, 1.5m
DVI-D to DVI-D connector, Detachable, 1.5m
Dimensions (W x H x D) / Weight (Simple Stand)
485.8 x 325.9 x 72.6 mm (19.1 x 12.8 x 2.9 inch) (Without Stand)
485.8 x 373.5 x 200 mm (19.1 x 14.7 x 7.9 inch) (With Stand) / 4.45 kg(9.8 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
40 watts
Blinking
Less than 1 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 800
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1600 x 900
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
56.476
60.023
67.500
49.702
62.795
55.935
70.635
60.000
Vertical
Frequency (Hz)
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.087
66.667
74.551
75.062
59.940
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
Sync Polarity
(H/V)
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/+
-/-
-/-
-/-
-/-
70.069
75.029
75.000
78.750
-/-
+/+
75.000 108.000 +/+
59.810 83.50 -/+
74.934 106.500 -/+
59.887 106.500 -/+
74.984
60.000
136.750
108.000
-/+
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2033SW PLUS
20 inch (50 cm)
442.8 mm (H) x 249.075 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.2768 mm (H) x 0.2768 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1600 x 900@60 Hz
Maximum resolution
Input Signal, Terminated
1600 x 900@60 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
150 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable, 1.5m
DVI-D to DVI-D connector, Detachable, 1.5m
Dimensions (W x H x D) / Weight (Simple Stand)
485.8 x 325.9 x 72.6 mm (19.1 x 12.8 x 2.9 inch) (Without Stand)
485.8 x 373.5 x 200 mm (19.1 x 14.7 x 7.9 inch) (With Stand) / 4.45 kg(9.8 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
40 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 800
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1600 x 900
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
35.156
37.879
48.077
46.875
48.363
56.476
60.023
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
37.861
37.500
67.500
49.702
62.795
55.935
70.635
60.000
Vertical
Frequency (Hz)
56.250
60.317
72.188
75.000
60.004
70.069
75.029
70.087
66.667
74.551
75.062
59.940
72.809
75.000
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
Sync Polarity
(H/V)
+/+
+/+
+/+
+/+
-/-
-/-
+/+
-/-
-/-
-/-
-/-
-/+
-/-
-/-
75.000 108.000 +/+
59.810 83.50 -/+
74.934 106.500 -/+
59.887 106.500 -/+
74.984
60.000
136.750
108.000
-/+
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233BW
22 inch (55 cm)
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.282 mm (H) x 0.282 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1680 x 1050@60 Hz
Maximum resolution
Input Signal, Terminated
1680 x 1050@60 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
45 watts
Blinking
Less than 1 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 960
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1680 x 1050
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
Vertical
Frequency (Hz)
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.087
66.667
74.551
75.062
59.94
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
Sync Polarity
(H/V)
56.476
60.023
67.500
49.702
60.000
63.981
79.976
55.935
70.069
75.029
75.000
75.025
59.887
75.000
78.750
108.000
59.810 83.500 -/+
60.000 108.000 +/+
60.020 108.000 +/+
135.000
106.500
-/-
+/+
+/+
+/+
-/+
70.635
65.290
74.984
59.954
136.750
146.250
-/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/+
-/-
-/-
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233BW PLUS
22 inch (55 cm)
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.282 mm (H) x 0.282 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1680 x 1050@60 Hz
Maximum resolution
Input Signal, Terminated
1680 x 1050@60 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
45 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 960
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1680 x 1050
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
35.156
37.879
48.077
46.875
48.363
56.476
60.023
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
37.861
37.500
Vertical
Frequency (Hz)
56.250
60.317
72.188
75.000
60.004
70.069
75.029
70.087
66.667
74.551
75.062
59.94
72.809
75.000
Pixel Clock
(MHz)
36.000
40.000
50.000
49.500
65.000
75.000
78.750
28.322
30.240
57.284
100.000
25.175
31.500
31.500
Sync Polarity
(H/V)
67.500
49.702
60.000
63.981
79.976
55.935
70.635
75.000 108.000 +/+
59.810 83.500 -/+
60.000 108.000 +/+
60.020 108.000 +/+
75.025
59.887
74.984
135.000
106.500
136.750
+/+
-/+
-/+
65.290 59.954 146.250 -/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
+/+
+/+
+/+
+/+
-/-
-/-
+/+
-/-
-/-
-/-
-/-
-/+
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233GW
22 inch (55 cm)
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.282 mm (H) x 0.282 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1680 x 1050@60 Hz
Maximum resolution
Input Signal, Terminated
1680 x 1050@60 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State Normal Operation Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off Power Indicator
Power Consumption
On
45 watts Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 960
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1680 x 1050
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
37.861
37.500
35.156
37.879
48.077
46.875
48.363
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
Vertical
Frequency (Hz)
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.087
66.667
74.551
75.062
59.94
Pixel Clock
(MHz)
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
Sync Polarity
(H/V)
56.476
60.023
67.500
49.702
60.000
63.981
79.976
55.935
70.069
75.029
75.000
75.025
59.887
75.000
78.750
108.000
59.810 83.500 -/+
60.000 108.000 +/+
60.020 108.000 +/+
135.000
106.500
-/-
+/+
+/+
+/+
-/+
70.635
65.290
74.984
59.954
136.750
146.250
-/+
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/+
-/-
-/-
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233GW PLUS
22 inch (55 cm)
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
Synchronization
Horizontal
Vertical
Display Color
16.7M
Resolution
Optimum resolution
0.282 mm (H) x 0.282 mm (V)
30 ~ 81 kHz
56 ~ 75 Hz
1680 x 1050@60 Hz
Maximum resolution
Input Signal, Terminated
1680 x 1050@60 Hz
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
45 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 960
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1680 x 1050
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
35.156
37.879
48.077
46.875
48.363
56.476
60.023
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
37.861
37.500
Vertical
Frequency (Hz)
56.250
60.317
72.188
75.000
60.004
70.069
75.029
70.087
66.667
74.551
75.062
59.94
72.809
75.000
Pixel Clock
(MHz)
36.000
40.000
50.000
49.500
65.000
75.000
78.750
28.322
30.240
57.284
100.000
25.175
31.500
31.500
Sync Polarity
(H/V)
67.500
49.702
60.000
63.981
79.976
55.935
70.635
75.000 108.000 +/+
59.810 83.500 -/+
60.000 108.000 +/+
60.020 108.000 +/+
75.025
59.887
74.984
135.000
106.500
136.750
+/+
-/+
-/+
65.290 59.954 146.250 -/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
+/+
+/+
+/+
+/+
-/-
-/-
+/+
-/-
-/-
-/-
-/-
-/+
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233NW
22 inch (55 cm)
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.282 mm (H) x 0.282 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
56 ~ 75 Hz
1680 x 1050@60 Hz
Maximum resolution
Input Signal, Terminated
RGB Analog,
1680 x 1050@60 Hz
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
45 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 960
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1680 x 1050
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
72.188
75.000
60.004
70.069
75.029
75.000
59.810
60.000
60.020
75.025
59.887
74.984
59.954
70.087
66.667
74.551
75.062
59.94
72.809
75.000
56.250
60.317
48.077
46.875
48.363
56.476
60.023
67.500
49.702
60.000
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
37.861
37.500
35.156
37.879
63.981
79.976
55.935
70.635
65.290
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
50.000
49.500
65.000
75.000
78.750
108.000
83.500
108.000
108.000
135.000
106.500
136.750
146.250
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
+/+
+/+
-/+
+/+
+/+
+/+
-/-
-/-
+/+
+/+
-/+
-/+
-/+
-/-
-/-
-/-
+/+
+/+
-/+
-/-
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233NWPLUS
22 inch (55 cm)
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.282 mm (H) x 0.282 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
56 ~ 75 Hz
1680 x 1050@60 Hz
Maximum resolution
Input Signal, Terminated
RGB Analog,
1680 x 1050@60 Hz
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
45 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 960
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1440 x 900
VESA, 1680 x 1050
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
72.188
75.000
60.004
70.069
75.029
75.000
59.810
60.000
60.020
75.025
59.887
74.984
59.954
70.087
66.667
74.551
75.062
59.94
72.809
75.000
56.250
60.317
48.077
46.875
48.363
56.476
60.023
67.500
49.702
60.000
Horizontal
Frequency
(kHz)
31.469
35.000
49.726
68.681
31.469
37.861
37.500
35.156
37.879
63.981
79.976
55.935
70.635
65.290
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
50.000
49.500
65.000
75.000
78.750
108.000
83.500
108.000
108.000
135.000
106.500
136.750
146.250
28.322
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
+/+
+/+
-/+
+/+
+/+
+/+
-/-
-/-
+/+
+/+
-/+
-/+
-/+
-/-
-/-
-/-
+/+
+/+
-/+
-/-
-/-
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233SN
21.5 inch (54.68 cm)
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.248 mm (H) x 0.248 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
31 ~ 80kHz
50 ~ 75Hz
1920 x 1080@60 Hz
Maximum resolution
Input Signal, Terminated
RGB Analog,
1920 x 1080@60 Hz
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
162 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
519 x 344.7 x 71.1 mm (20.4 x 13.6 x 2.8 inch) (Without Stand)
519 x 392.3 x 208.7 mm (20.4 x 15.4 x 8.2 inch) (With Stand) / 4.40 kg (9.7 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
45 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERG Y2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1600 X 1200
VESA, 1680 X 1050
VESA, 1920 X 1080
Horizontal
Frequency
(kHz)
31.469
35.156
37.879
48.363
49.702
60.000
63.981
55.935
75.000
65.290
66.587
Vertical
Frequency (Hz)
59.940
56.250
60.317
60.004
59.810
60.000
60.020
59.887
60.000
59.954
59.934
Pixel Clock
(MHz)
25.175
36.000
40.000
65.000
83.500
108.000
108.000
106.500
162.000
146.250
138.500
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
+/-
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233SNPLUS
21.5 inch (54.68 cm)
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.248 mm (H) x 0.248 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
31 ~ 80kHz
50 ~ 75Hz
1920 x 1080@60 Hz
Maximum resolution
Input Signal, Terminated
RGB Analog,
1920 x 1080@60 Hz
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
162 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
519 x 344.7 x 71.1 mm (20.4 x 13.6 x 2.8 inch) (Without Stand)
519 x 392.3 x 208.7 mm (20.4 x 15.4 x 8.2 inch) (With Stand) / 4.40 kg (9.7 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
General
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
45 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERG Y2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1600 X 1200
VESA, 1680 X 1050
VESA, 1920 X 1080
Horizontal
Frequency
(kHz)
31.469
35.156
37.879
48.363
49.702
60.000
63.981
55.935
75.000
65.290
66.587
Vertical
Frequency (Hz)
59.940
56.250
60.317
60.004
59.810
60.000
60.020
59.887
60.000
59.954
59.934
Pixel Clock
(MHz)
25.175
36.000
40.000
65.000
83.500
108.000
108.000
106.500
162.000
146.250
138.500
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
+/-
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233SW
21.5 inch (54.68 cm)
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.248 mm (H) x 0.248 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
31 ~ 80 kHz
50 ~ 75 Hz
1920 x 1080@60 Hz
Maximum resolution 1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
162 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
519 x 344.7 x 71.1 mm (20.4 x 13.6 x 2.8 inch) (Without Stand)
519 x 392.3 x 208.7 mm (20.4 x 15.4 x 8.2 inch) (With Stand) / 4.40 kg (9.7 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
45 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1280 X 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1600 X 1200
VESA, 1680 X 1050
VESA, 1920 X 1080
Horizontal
Frequency
(kHz)
31.469
35.156
37.879
48.363
49.702
60.000
63.981
55.935
75.000
65.290
66.587
Vertical
Frequency (Hz)
59.940
56.250
60.317
60.004
59.810
60.000
60.020
59.887
60.000
59.954
59.934
Pixel Clock
(MHz)
25.175
36.000
40.000
65.000
83.500
108.000
108.000
106.500
162.000
146.250
138.500
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
+/-
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2233SW PLUS
21.5 inch (54.68 cm)
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.248 mm (H) x 0.248 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
31 ~ 80 kHz
50 ~ 75 Hz
1920 x 1080@60 Hz
Maximum resolution 1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
162 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
519 x 344.7 x 71.1 mm (20.4 x 13.6 x 2.8 inch) (Without Stand)
519 x 392.3 x 208.7 mm (20.4 x 15.4 x 8.2 inch) (With Stand) / 4.40 kg (9.7 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
45 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1280 X 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1600 X 1200
VESA, 1680 X 1050
VESA, 1920 X 1080
Horizontal
Frequency
(kHz)
31.469
35.156
37.879
48.363
49.702
60.000
63.981
55.935
75.000
65.290
66.587
Vertical
Frequency (Hz)
59.940
56.250
60.317
60.004
59.810
60.000
60.020
59.887
60.000
59.954
59.934
Pixel Clock
(MHz)
25.175
36.000
40.000
65.000
83.500
108.000
108.000
106.500
162.000
146.250
138.500
Sync Polarity
(H/V)
+/+
-/+
+/-
-/+
+/+
+/+
-/+
-/-
+/+
+/+
-/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2333GWPLUS
23 inch (58 cm)
509.76 mm (H) x 286.74 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.2655 mm (H) x 0.2655 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 75 kHz
56 ~ 61 Hz
1920 x 1080@60 Hz
Maximum resolution 1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable , 1.5m
DVI-D to DVI-D connector, Detachable , 1.5m
Dimensions (W x H x D) / Weight (Simple Stand)
557.3 x 365.8 x 71.5 mm (21.9 x 14.4 x 2.8 inch) (Without Stand)
557.3 x 415.7 x 218.6 mm (21.9 x 16.4 x 8.6 inch) (With Stand) / 5.4 kg (10.4 lbs)
VESA Mounting Interface
100.0 mm x 100.0 mm
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
ON
45 watts
Power saving mode blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1280 X 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1600 X 1200
VESA, 1680 X 1050
VESA, 1920 X 1080
Horizontal
Frequency
(kHz)
31.469
35.156
37.879
48.363
49.702
60.000
63.981
55.935
75.000
65.290
66.587
Vertical
Frequency (Hz)
59.940
56.250
60.317
60.004
59.810
60.000
60.020
59.887
60.000
59.954
59.934
Pixel Clock
(MHz)
25.175
36.000
40.000
65.000
83.500
108.000
108.000
106.500
162.000
146.250
138.500
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
+/-
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2333SW
23 inch (58 cm)
509.76 mm (H) x 286.74 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.2655 mm (H) x 0.2655 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 75 kHz
56 ~ 61 Hz
1920 x 1080@60 Hz
Maximum resolution 1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
557.3 x 365.8 x 71.5 mm (21.9 x 14.4 x 2.8 inch) (Without Stand)
557.3 x 415.7 x 218.6 mm (21.9 x 16.4 x 8.6 inch) (With Stand) / 5.4 kg (11.9 lbs)
VESA Mounting Interface
100.0 mm x 100.0 mm
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
ON
45 watts
Power saving mode blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1280 X 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1600 X 1200
VESA, 1680 X 1050
VESA, 1920 X 1080
Horizontal
Frequency
(kHz)
31.469
35.156
37.879
48.363
49.702
60.000
63.981
55.935
75.000
65.290
66.587
Vertical
Frequency (Hz)
59.940
56.250
60.317
60.004
59.810
60.000
60.020
59.887
60.000
59.954
59.934
Pixel Clock
(MHz)
25.175
36.000
40.000
65.000
83.500
108.000
108.000
106.500
162.000
146.250
138.500
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
+/-
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2333SWPLUS
23 inch (58 cm)
509.76 mm (H) x 286.74 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.2655 mm (H) x 0.2655 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 75 kHz
56 ~ 61 Hz
1920 x 1080@60 Hz
Maximum resolution 1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
557.3 x 365.8 x 71.5 mm (21.9 x 14.4 x 2.8 inch) (Without Stand)
557.3 x 415.7 x 218.6 mm (21.9 x 16.4 x 8.6 inch) (With Stand) / 5.4 kg (11.9 lbs)
VESA Mounting Interface
100.0 mm x 100.0 mm
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
ON
45 watts
Power saving mode blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1280 X 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1440 X 900
VESA, 1600 X 1200
VESA, 1680 X 1050
VESA, 1920 X 1080
Horizontal
Frequency
(kHz)
31.469
35.156
37.879
48.363
49.702
60.000
63.981
55.935
75.000
65.290
66.587
Vertical
Frequency (Hz)
59.940
56.250
60.317
60.004
59.810
60.000
60.020
59.887
60.000
59.954
59.934
Pixel Clock
(MHz)
25.175
36.000
40.000
65.000
83.500
108.000
108.000
106.500
162.000
146.250
138.500
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
+/-
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2433BW
24 inch (61 cm)
518.4 mm (H) x 324.0 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.270 mm (H) x 0.270 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
50 ~ 63 Hz
1920 x 1200@60 Hz
Maximum resolution 1920 x 1200@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
569.5 x 403.0 x 71.1 mm / 22.4 x 15.9 x 2.8 inch (Without Stand)
569.5 x 453.4 x 218.7 mm / 22.4 x 17.9 x 8.6 inch (With Stand), 5.8 kg / 12.8 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
50 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA,1024 x 768
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA,1440 x 900
VESA,1600 X 1200
VESA, 1680 x 1050
VESA, 1920 X 1200
Horizontal
Frequency
(kHz)
31,469
35,156
37,879
48,363
49,702
60,000
63,981
55,935
75,000
65,290
74,556
Vertical
Frequency (Hz)
59,940
56,250
60,317
60,004
59,810
60,000
60,020
59,887
60,000
59,954
59,885
Pixel Clock
(MHz)
25,175
36,000
40,000
65,000
83,500
108,000
108,000
106,500
162,000
146,250
193,250
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
-/+
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2433BWPLUS
24 inch (61 cm)
518.4 mm (H) x 324.0 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.270 mm (H) x 0.270 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
50 ~ 63 Hz
1920 x 1200@60 Hz
Maximum resolution 1920 x 1200@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
569.5 x 403.0 x 71.1 mm / 22.4 x 15.9 x 2.8 inch (Without Stand)
569.5 x 453.4 x 218.7 mm / 22.4 x 17.9 x 8.6 inch (With Stand), 5.8 kg / 12.8 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
50 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA,1024 x 768
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA,1440 x 900
VESA,1600 X 1200
VESA, 1680 x 1050
VESA, 1920 X 1200
Horizontal
Frequency
(kHz)
31,469
35,156
37,879
48,363
49,702
60,000
63,981
55,935
75,000
65,290
74,556
Vertical
Frequency (Hz)
59,940
56,250
60,317
60,004
59,810
60,000
60,020
59,887
60,000
59,954
59,885
Pixel Clock
(MHz)
25,175
36,000
40,000
65,000
83,500
108,000
108,000
106,500
162,000
146,250
193,250
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
-/+
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2433GW
24 inch (61 cm)
518.4 mm (H) x 324.0 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.270 mm (H) x 0.270 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
50 ~ 63 Hz
1920 x 1200@60 Hz
Maximum resolution 1920 x 1200@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
569.5 x 403.0 x 71.1 mm / 22.4 x 15.9 x 2.8 inch (Without Stand)
569.5 x 453.4 x 218.7 mm / 22.4 x 17.9 x 8.6 inch (With Stand), 5.8 kg / 12.8 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
50 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA,1024 x 768
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA,1440 x 900
VESA,1600 X 1200
VESA, 1680 x 1050
VESA, 1920 X 1200
Horizontal
Frequency
(kHz)
31,469
35,156
37,879
48,363
49,702
60,000
63,981
55,935
75,000
65,290
74,556
Vertical
Frequency (Hz)
59,940
56,250
60,317
60,004
59,810
60,000
60,020
59,887
60,000
59,954
59,885
Pixel Clock
(MHz)
25,175
36,000
40,000
65,000
83,500
108,000
108,000
106,500
162,000
146,250
193,250
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
-/+
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2433GWPLUS
24 inch (61 cm)
518.4 mm (H) x 324.0 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.270 mm (H) x 0.270 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81 kHz
50 ~ 63 Hz
1920 x 1200@60 Hz
Maximum resolution 1920 x 1200@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
569.5 x 403.0 x 71.1 mm / 22.4 x 15.9 x 2.8 inch (Without Stand)
569.5 x 453.4 x 218.7 mm / 22.4 x 17.9 x 8.6 inch (With Stand), 5.8 kg / 12.8 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
50 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA,1024 x 768
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA,1440 x 900
VESA,1600 X 1200
VESA, 1680 x 1050
VESA, 1920 X 1200
Horizontal
Frequency
(kHz)
31,469
35,156
37,879
48,363
49,702
60,000
63,981
55,935
75,000
65,290
74,556
Vertical
Frequency (Hz)
59,940
56,250
60,317
60,004
59,810
60,000
60,020
59,887
60,000
59,954
59,885
Pixel Clock
(MHz)
25,175
36,000
40,000
65,000
83,500
108,000
108,000
106,500
162,000
146,250
193,250
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
-/+
-/-
+/+
+/+
-/-
Specifications
General
Model Name
LCD Panel
Size
Display area
SyncMaster 2433LW
23.6 inch (59.8 cm)
521.28 mm (H) x 293.22 mm (V)
Pixel Pitch
Synchronization
Horizontal
0.2715 mm (H) x 0.2715 mm (V)
Vertical
Display Color
16.7M
Resolution
Optimum resolution
30 ~ 81kHz
56 ~ 60 Hz
1920 x 1080@60 Hz
Maximum resolution 1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
579.1 x378.2 x 75.6 mm / 22.8 x 14.9 x 3.0 inch (Without Stand)
579.1 x 428.0 x 218.6 mm / 22.8 x 16.9 x 8.6 inch (With Stand), 5.6 kg / 12.3 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
General
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
On
44 watts
Power saving mode
Blinking
Less than 1 watts
Power off (Power button)
EPA/ENERGY 2000
Off
Less than 1 watts
This monitor is EPA ENERGY STAR
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality.
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA,1024 x 768
VESA, 1280 x 800
VESA, 1280 X 960
VESA, 1280 X 1024
VESA,1440 x 900
VESA,1600 X 1200
VESA, 1680 x 1050
VESA, 1920 X 1200
Horizontal
Frequency
(kHz)
31,469
35,156
37,879
48,363
49,702
60,000
63,981
55,935
75,000
65,290
74,556
Vertical
Frequency (Hz)
59,940
56,250
60,317
60,004
59,810
60,000
60,020
59,887
60,000
59,954
59,885
Pixel Clock
(MHz)
25,175
36,000
40,000
65,000
83,500
108,000
108,000
106,500
162,000
146,250
193,250
Sync Polarity
(H/V)
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
-/+
+/+
+/+
-/+
+/+
-/+
-/+
-/-
+/+
+/+
-/-
Information
For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD.
• Resolution: **** x ****
• Vertical frequency (refresh rate): 60 Hz
TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems.
When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the LCD area but rub softly.
If excessive force is applied, you may stain it.
If you are not satisfied with the picture quality, you can get better quality of picture by performing the "Auto Adjustment function" in display screen that is appeared as window termination button is pressed.
If there's still noise after the automatic adjustment, use the Fine/Coarse adjustment function.
When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear.
Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time.
This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained
45
Information when switching to a new video image. All display products, including LCD, are subject to image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention.
Power Off, Screen Saver, or Power Save Mode
Ex)
• Turn the power off when using a stationary pattern.
• Turn the power off for 4 hours after 20 hours in use
• Turn the power off for 2 hours after 12 hours in use
• Use a Screen saver if possible
• Screen saver in one color or a moving image is recommended.
• Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large difference in luminance.
Avoid using Grey colors, which can cause Image retention easily.
• Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex)
• Recommended settings: Bright colors with little difference in luminance
• Change the characters color and background color every 30 minutes
46
Information
Ex)
• Every 30 minutes, change the characters with movement.
Ex)
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean.
When this occurs, the previous image may be seen when the pattern is changed.
To prevent this, the accumulated voltage difference must be decreased.
47
Information
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
48
Appendix
Contact SAMSUNG WORLDWIDE
Note
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
U.S.A
CANADA
MEXICO
North America
1-800-SAMSUNG(726-7864) http://www.samsung.com/us
1-800-SAMSUNG(726-7864) http://www.samsung.com/ca
01-800-SAMSUNG(726-7864) http://www.samsung.com/mx
ARGENTINA
BRAZIL
Latin America
0800-333-3733
0800-124-421 http://www.samsung.com/ar http://www.samsung.com/br
CHILE
COLOMBIA
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
HONDURAS
JAMAICA
NICARAGUA
PANAMA
PUERTO RICO
4004-0000
800-SAMSUNG(726-7864)
01-8000112112
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
800-7919267
1-800-234-7267
00-1800-5077267
800-7267
1-800-682-3180
REP. DOMINICA 1-800-751-2676 http://www.samsung.com/cl http://www.samsung.com/co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin
TRINIDAD & TO-
BAGO
1-800-SAMSUNG(726-7864) http://www.samsung.com/latin
VENEZUELA 0-800-100-5303 http://www.samsung.com/latin
AUSTRIA
BELGIUM
Europe
0810 - SAMSUNG(7267864, €
0.07/min) http://www.samsung.com/at
02 201 2418 http://www.samsung.com/be
(Dutch) http://www.samsung.com/be_fr
(French)
CZECH REPUBLIC 800 - SAMSUNG (800-726786) http://www.samsung.com/cz
DENMARK
EIRE
8 - SAMSUNG (7267864)
0818 717 100
49 http://www.samsung.com/dk http://www.samsung.com/ie
Appendix
FINLAND
FRANCE
GERMANY
Europe
30 - 6227 515
01 4863 0000 http://www.samsung.com/fi http://www.samsung.com/fr
01805 - SAMSUNG (7267864, €
0.14/Min) http://www.samsung.de
HUNGARY
ITALIA
06-80-SAMSUNG(726-7864) http://www.samsung.com/hu
800-SAMSUNG(726-7864) http://www.samsung.com/it
LUXEMBURG 02 261 03 710 http://www.samsung.com/lu
NETHERLANDS 0900 - SAMSUNG
(0900-7267864) (€ 0.10/Min) http://www.samsung.com/nl
NORWAY
POLAND
3 - SAMSUNG (7267864)
0 801 1SAMSUNG (172678) http://www.samsung.com/no http://www.samsung.com/pl
PORTUGAL
SLOVAKIA
SPAIN
022 - 607 - 93 - 33
808 20 - SAMSUNG (7267864) http://www.samsung.com/pt
0800-SAMSUNG(726-7864) http://www.samsung.com/sk
902 - 1 - SAMSUNG (902 172
678) http://www.samsung.com/es
SWEDEN
SWITZERLAND
075 - SAMSUNG (726 78 64) http://www.samsung.com/se
0848-SAMSUNG(7267864,
CHF 0.08/min) http://www.samsung.com/ch
U.K
0845 SAMSUNG (7267864) http://www.samsung.com/uk
ESTONIA
LATVIA
LITHUANIA
KAZAKHSTAN
KYRGYZSTAN
RUSSIA
TADJIKISTAN
UKRAINE
UZBEKISTAN
CIS
800-7267
8000-7267
8-800-77777
8-10-800-500-55-500
00-800-500-55-500
8-800-555-55-55
8-10-800-500-55-500
8-800-502-0000
8-10-800-500-55-500 http://www.samsung.com/ee http://www.samsung.com/lv http://www.samsung.com/lt http://www.samsung.com/kz_ru http://www.samsung.ru
http://www.samsung.ua
http://www.samsung.com/kz_ru
AUSTRALIA
CHINA
INDIA
INDONESIA
1300 362 603
800-810-5858
Asia Pacific
400-810-5858
010-6475 1880
HONG KONG:3698 - 4698
3030 8282
1800 110011
1-800-3000-8282
0800-112-8888 http://www.samsung.com/au http://www.samsung.com/cn http://www.samsung.com/hk http://www.samsung.com/in http://www.samsung.com/id
50
Appendix
Asia Pacific
JAPAN
MALAYSIA
0120-327-527
1800-88-9999 http://www.samsung.com/jp http://www.samsung.com/my
NEW ZEALAND 0800 SAMSUNG (0800 726
786) http://www.samsung.com/nz
PHILIPPINES 1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph
SINGAPORE
THAILAND
TAIWAN
VIETNAM
1800-3-SAMSUNG(726-7864)
02-5805777
1800-SAMSUNG(726-7864) http://www.samsung.com/sg
1800-29-3232 http://www.samsung.com/th
02-689-3232
0800-329-999
1 800 588 889 http://www.samsung.com/tw http://www.samsung.com/vn
Middle East & Africa
SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.com/za
TURKEY
U.A.E
444 77 11
800-SAMSUNG(726-7864) http://www.samsung.com/tr http://www.samsung.com/ae
8000-4726
Terms
Dot Pitch
Vertical Frequency
Horizontal Frequency
Interlace and Non-Interlace
Methods
Plug & Play
The image on a monitor is composed of red, green and blue dots.
The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm
The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh
Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard
VESA DDC for the Plug & Play function.
51
Appendix
Resolution The number of horizontal and vertical dots used to compose the screen image is called the 'resolution'. This number shows the accuracy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen.
Example: If the resolution is **** x ****, this means the screen is composed of **** horizontal dots (horizontal resolution) and
**** vertical lines (vertical resolution).
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) -
Europe only
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Authority
Information in this document is subject to change without notice.
© 2009 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.,
Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR ® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR ®
Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY
STAR ® guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.
52
advertisement
Key Features
- 61 cm (24") LED TN
- Full HD 1920 x 1200 pixels 16:10
- 5 ms 300 cd/m² 1000:1
Related manuals
advertisement
Table of contents
- 1 LCD Monitor
- 2 Safety Instructions
- 2 Notational
- 2 Power
- 3 Installation
- 4 Clean
- 5 Others
- 9 Introduction
- 9 Package Contents
- 10 Your Monitor
- 14 Connections
- 14 Connecting Cables
- 15 Using the Stand
- 17 Using the Software
- 17 Monitor Driver
- 25 Natural Color
- 25 MagicTune™
- 27 MultiScreen
- 29 Adjusting the Monitor
- 29 Direct Functions
- 30 OSD Function
- 38 Troubleshooting
- 38 Self-Test Feature Check
- 39 Check List
- 43 Q & A
- 45 Specifications
- 45 SyncMaster 633NW
- 49 SyncMaster 733A
- 53 SyncMaster 733APLUS
- 57 SyncMaster 733N
- 61 SyncMaster 733NPLUS
- 65 SyncMaster 733NW
- 69 SyncMaster 933BW
- 73 SyncMaster 933BWPLUS
- 77 SyncMaster 933GW
- 81 SyncMaster 933GWPLUS
- 85 SyncMaster 933NW
- 89 SyncMaster 933NWPLUS
- 93 SyncMaster 933SN
- 97 SyncMaster 933SNPLUS
- 101 SyncMaster 2033SN
- 105 SyncMaster 2033SNPLUS
- 109 SyncMaster 2033SW
- 113 SyncMaster 2033SWPLUS
- 117 SyncMaster 2233BW
- 121 SyncMaster 2233BWPLUS
- 125 SyncMaster 2233GW
- 129 SyncMaster 2233GWPLUS
- 133 SyncMaster 2233NW
- 137 SyncMaster 2233NWPLUS
- 141 SyncMaster 2233SN
- 145 SyncMaster 2233SNPLUS
- 149 SyncMaster 2233SW
- 153 SyncMaster 2233SWPLUS
- 157 SyncMaster 2333GWPLUS
- 161 SyncMaster 2333SW
- 165 SyncMaster 2333SWPLUS
- 169 SyncMaster 2433BW
- 173 SyncMaster 2433BWPLUS
- 177 SyncMaster 2433GW
- 181 SyncMaster 2433GWPLUS
- 185 SyncMaster 2433LW
- 189 Information
- 189 For Better Display
- 189 PRODUCT INFORMATION (Image Retention Free)
- 193 Appendix
- 193 Contact SAMSUNG WORLDWIDE
- 195 Terms
- 196 Correct Disposal
- 196 Authority