Set-up
your portable alarm
tattletale
unbeatable portable alarms
Now you can protect anything, anywhere, anytime. Instantly.
Protect
1
Simply fill out the
activation sheet
Fax it to us at 1.888.765.1671.
tattletale will call you to confirm that
your monitoring has been activated.
right now
2
3
Plug it in
Place your tattletale on a stable,
horizontal surface.
Test your protection
Call tattletale at 1. 888. TELL. ON. U.
(835-5668) and indicate that you
would like to perform a test.
The internal motion detector has a
range of 50 feet and sees at a 90˚
angle.
Press the
*
and
#
keys at the same
time. This sends an instant alarm to
the monitoring station. Watch the
"tattletale" light or the "CALLING"
90
light on the front of your unit. If the
˚
tattletale light is:
Protect a room
FLASHING = ALARM SENT
ON = ALARM SIGNAL RECEIVED
For easy arming and disarming
choose a location that will be easily
accessible to you when you enter and
exit. Make sure there is an electrical
The person on the phone will let you
know if the signal was received.
outlet nearby. Plug it in.
Connect anywhere to 24/7
nationwide wireless monitoring
This will activate the "POWER"
Got Cell Service ?
indicator lights (on the front and top
of the unit). Wait 60 seconds for a
Check the "CELL" light on top of the
"beep" indicating the unit is warmed
tattletale. If the light is:
up and ready to proceed.
OFF = NO SERVICE
FLASHING = ADEQUATE CELL SIGNAL
AMPS package:
includes AC/DC inverter,
battery charger
(requires marine battery)
Protect without AC power
ON = FULL CELL SIGNAL
change how you protect everything
Create
4
your wireless perimeter
Position your accessories
About zones
Sensors can have their
own address
Zone lights
You can place up to 16 additional
Each accessory is assigned to a
Since your alarm has long range
Zone lights are located on the top of
indoor/outdoor sensors 2000' away
zone. Each zone can hold up to two
wireless capability you may choose
the tattletale Base Unit.
from the tattletale Base Unit. The
accessories. Each of your sensors
to install sensors at different
The zone lights show the location
sensors are already programmed to
has a zone location labelled on the
addresses. In the event of an alarm
and status of each accessory. If the
light associated with an accessory is:
work with the alarm.
back. These locations correspond
at one of these addresses you will
to the zone lights on your alarm. To
want the police to respond to the
help you remember this
address of the sensor.
information, your alarm unit has a
Call tattletale at 1.888.835.5668
sticker on the bottom that labels
and give us the zone number on
zone locations.
the back of the sensor and the
OFF = OK
FLASHING = ACCESSORY IS TRIPPED
OR OPEN
RAPIDLY FLASHING = LOW BATTERY
OR OUT OF RANGE
address.
2000' LONG-RANGE –WIRELESS
OUTDOOR
INDOOR
Smoke detector
Automatically notifies
the fire department
Door/window sensor
Secure any opening
Long range
door sensor
Protects up to
4000' away
Glass break detector
hears glass breaking
up to 25' away
Indoor motion detector
Senses motion up to
50' away
Long range
signal booster
Extend your wireless
force field in 4000'
increments
Outdoor
motion detector
Protect any fenced-in
area. Senses up to 50'
away
The LOOP long range
electronic lock
Tie up anything up to
4000' away
t h e LOOP
Relax
5
Create your master code
you're in control
You have 60 seconds to leave the area.
After 50 seconds you will hear three
Choose a four digit master code to
8
When you have an alarm
Add up to 6 additional
user codes
beeps indicating that you have 10
The siren will sound for 8 minutes
seconds remaining to leave.
unless your code is entered.
with a pre-programmed master code
If the ready light is off check the
The strobe light will flash until your
Select a code number from 2-7 (for
of 1-2-3-4.
"ZONE" lights. If any (other than zone
code is entered (this is a safety feature
example code 2)
3) are flashing you must make sure the
so that you do not enter a dangerous
sensor on that zone is not being
area).
PRESS * 2 #
The "tattletale" calling light flashes
ENTER YOUR MASTER CODE
arm and disarm your tattletale.
To create your new code:
PRESS *
1
tripped or open before you can arm
#
your alarm. Close any doors or Loops.
PRESS 1 2 3 4
Now you can arm your alarm.
when sending the instant signal to
tattletale dispatch. tattletale dispatch
PRESS *
1
#
To send an immediate
alarm signal
ENTER YOUR NEW FOUR DIGIT
MASTER CODE
PRESS THE * AND # KEYS AT THE
SAME TIME
PRESS *
1
Have the user create a 4 digit code
that can be easily remembered.
The tattletale comes from the factory
6
9
# TO EXIT
Arm your alarm
ENTER YOUR MASTER CODE
OR
PRESS THE ON BUTTON ON YOUR KEY
7
PRESS * 2 # (AGAIN)
will page your alarm back after the
signal is received (usually about 60
ENTER THE USER 2 USE CODE
seconds).
PRESS * 2 # (AGAIN)
Dispatch will call your "primary
contact" number to ask for your
You can repeat these steps as often
password. If the operator cannot reach
as needed to add additional user
you or the person that answers the
codes.
phone gives the wrong password the
police or fire department will be
Remember: record each code and the
called. Your "additional contacts" will
user’s name in a safe place away from
You will have 40 seconds to enter
be called and asked to meet the police
your tattletale.
your code after you hear a warning
or fire personnel.
Disarm your alarm
Delete a user code
tone.
IF THE ALARM IS A MISTAKE YOU CAN
CHAIN REMOTE
ENTER YOUR MASTER CODE
CALL TATTLETALE DISPATCH AND
The "ARMED" light will now be on.
ENTER YOUR MASTER CODE
OR
Key chain remote control
One button on/off plus
panic
PRESS * 2 #
CANCEL: 1-888-tell-on-u
PRESS THE OFF BUTTON ON YOUR
KEYCHAIN REMOTE
PRESS * 2 # (AGAIN)
Remote siren/strobe
Project your alarm
outside
ENTER YOUR MASTER CODE
PRESS * 2 # (AGAIN)
Understand
your wireless protection
All-in-one portable alarm system
Zone indicator lights
Lighted keypad
Full 3 watt cell radio
115 db Siren
Safety strobe light
PIR motion detector
accessory status
arm/disarm
5x your cellphone
like a police siren
directs authorities to
location and
indicates alarm event
Senses heat and motion
up to 35' away
Status indicator lights
system status
Ready Light
ON = READY TO ARM
OFF = ACCESSORY IS TRIPPED
CHECK ZONE LIGHTS
Cell Light
OFF = NO SERVICE
FLASHING = ADEQUATE CELL
SIGNAL
ON = FULL CELL SIGNAL
Power Light
ON = POWER OK
FLASHING = BATTERY BACK-UP
OFF = NO POWER
Armed Light
ON =ALARM IS ARMED
FLASHING = NO DELAY
OFF = NOT ARMED
tattletale Light
FLASHING = ALARM SENT
ON = ALARM RECEIVED
Unbeatable protection
1. 888. TELL. ON. U.
Cellular radio
Instant wireless
transmission
Rattlesnake tamper
sensor
10 hour battery back-up
tattletale dispatch
no phone line to cut
signals tattletale dispatch
in .6 seconds
immediately trips alarm if
picked up or hit
works when the power is off
calls you when the battery is low
24/7 nationwide wireless
monitoring
www.tattletalealarm.com
Understand
your wireless protection
wireless sensors
alarm unit
Alarm beeps when you
try to arm it
Motion detector in a
metal storage container
Slow flash zone light
Wireless signals need a 3" crack
Zone light for an indoor
motion detector will not
flash
Alarm beeps when you
try to arm it
Check the power light
through metal. This is especially true
Battery saving feature on all
You have a remote sensor that is
if the motion detector is placed
wireless motion detectors
If it is off, your alarm is on battery
being tripped. Check the remote
inside a metal storage container and
sensor(s) that are assigned to that
the doors are closed.
To preserve battery life, so your
an outlet with power. This is a safety
batteries last 3-5 years, the motion
feature. Move your alarm to an outlet
Change the battery in an
indoor motion detector
detector will go into a sleep mode
with power.
zone. Make sure that all Loops are
locked, door/window sensors are
lined up with the magnet, and
for 3 minutes after it sees motion. It
will “wake up” only after it has had a
motion detectors are not seeing any
Press the reset button
motion.
back-up power and not plugged into
Bypass the zone and arm your alarm.
If the outlet has a push button fuse, it
period of 3 minutes of seeing
may be tripped. Try pressing the
nothing.
button on the outlet.
(for example zone 2)
Above the battery, slightly to the left
PRESS * 2 *
is a tiny square black button. After
Solution:
ENTER YOUR MASTER CODE TWICE TO
ENTER YOUR MASTERCODE TO
changing your battery you need to
To test the wireless motion
OVERRIDE
OVERRIDE THE ZONE
Rapid flash zone light
press the reset button. Battery
detector, place it in a drawer or
changes in all accessories require
somewhere where it will not see
pressing the reset button.
any movement for at least 3
Your alarm goes off before
you can disarm it
minutes. After 3 minutes, take the
Sensor is out of range.
Your tattletale is not seeing it. Bring
Less than 2000' range?
the sensor closer to your alarm and
motion detector out of the drawer
During the 40-second entry delay
and watch the corresponding zone
time, the RattleSnake™ vibration
light on the tattletale as you wave
detector inside the tattletale is
your hand in front of it.
active.
see if it stops flashing.
Wireless accessories will generally
or
work up to 2000 feet away from the
Battery may need to be replaced.
tattletale in an open field. Objects in-
You can usually find the batteries
between the accessory and the
wherever batteries are sold.
tattletale can decrease the range.
or
Metallic objects can affect range. To
Unplug your tattletale, take it to your
increase your range use signal
new location, and plug it in. Call
Bypass the zone nd arm your alarm.
boosters to create an extended
tattletale dispatch and update your
(for example zone 2)
wireless network.
information:
Sensor is missing.
When you move
ENTER YOUR MASTERCODE TWICE TO
OVERRIDE THE ZONE
of foam or a folded towel under the
tattletale to absorb some of the
- tattletale location
PRESS * 2 *
To solve this problem, place a piece
- verification number
- contact information
- local police and fire numbers.
Call customer support at 1-888-tell-on-u (835-5668) between 8 a.m. and 6 p.m. EST if you have a question.
vibrations when you come in.
">
