State 100313154 Premier® 66 gal. Tall 9kW Residential Hybrid Electric Heat Pump Water Heater Installation Manual

Installa on Instruc ons and

Use & Care Guide

Hybrid Electric

Heat Pump Water Heater

DO NOT RETURN THIS UNIT TO THE STORE

Read this manual and the labels on the water heater before you install, aren’t sure you can safely and properly do any of this work yourself:

• Call our Technical Assistance Hotline at 1-800-821-2017 . We can help you with installation, operations, troubleshooting, or maintenance. Before you call, write down the model and serial number from the water heater’s data plate.

Incorrect installa on, opera on, or service can damage the water heater, your house and other property, and present risks including fi re, scalding, electric shock, and explosion, causing serious injury or death.

LOW LEAD

CONTENT

Table of Contents Page

IMPORTANT SAFETY INFORMATION ................................. 3

GETTING STARTED ............................................................ 6

INSTALLATION ................................................................... 7

DIAGNOSTIC CODES ........................................................ 20

MAINTENANCE ............................................................... 26

REPAIR PARTS ILLUSTRATION .......................................... 31

Keep this manual in the pocket on heater for future reference whenever maintenance, adjustment or service is required.

Retain your original receipt as proof of purchase.

May 2016

100270591

COMPLETED INSTALLATION TYPICAL

Air Filter

TYPICAL INSTALLATION FOR 208V/240V

Condensate Drain

Access Cover

Connectivity Port

User Interface

Module (UIM)

xxxxx xxxxx xxxxx xxxxx

Temperature and

Pressure Relief Valve

Union*

Shut-off Valve

(Hot)

Upper Element and ECO

Hot

(Outlet)

Primary Condensate

Drain (3/4” PVC)

Discharge Pipe

(Do Not Cap or Plug)

Thermal Expansion Tank

Lower Element

Cold

(Inlet)

Drain Valve

Union*

Drain Pan Drain Line Drain

Shut-off Valve

(Cold)

*NOTE: If copper piping is used, unions must be dielectric at inlet and outlets.

2 • Residen al Hybrid Electric Heat Pump Water Heater Use and Care Guide

IMPORTANT SAFETY INFORMATION

Read and follow all safety messages and instruc ons in this manual.

serious injury or death. Do not remove any permanent instruc ons, labels, or the data plate from either the outside of the water heater or on the inside of the access panels. Keep this manual near the water heater.

This is the safety alert symbol. It is used to alert you to poten al physical injury hazards. Obey all safety messages that follow this symbol to avoid possible property damage,

Important informa on to keep

Fill out this sec on and keep this manual in the pocket of the water heater for reference.

Date Purchased:

Model number:

Serial number:

DANGER

WARNING

CAUTION

NOTICE

DANGER indicates hazardous situa on that, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situa on that, if not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situa on that, if not avoided, could result in minor or moderate injury.

NOTICE indicates prac ces not related to physical injury.

Maintenance performed:* Date:

*Drain and fl ush tank, clean air fi lter, clean condensate pan, and remove and inspect anode rod a er fi rst six months of opera on and at least annually therea er. Operate the Temperature and Pressure Relief Valve (T&P) annually and inspect T&P valve every 2-4 years (see the label on the T&P valve for maintenance schedule). See the Maintenance sec on for more informa on about maintaining this water heater.

Residen al Hybrid Electric Heat Pump Water Heater Use and Care Guide • 3


T

o reduce the risk of property damage, serious injury or death, read and follow the precau ons below, all labels on the water heater, and the safety messages and instruc ons throughout this manual.

RISKS DURING INSTALLATION

AND MAINTENANCE

Electric Shock Risk

Contact with the electrical parts in the junction box, behind the access doors and inside the top shroud can result in severe injury or death from electrical shock:

• Disconnect power by opening the circuit breaker or removing the fuses before installing or servicing.

• Use a non-contact circuit tester to confirm that power is off before working on or near any electrical parts.

• Replace the junction box cover and access doors after servicing.

Lifting Risk

The water heater is heavy. Follow these precau ons to reduce the risk of property damage, injuries from li ing or impact injuries from dropping the water heater.

• Use at least two people to lift the water heater.

• Be sure you both have a good grip before lifting.

• Unit is top heavy, u se an appliance dolly (with strap) to move the water heater.

RISKS DURING OPERATION

Scalding Risk

This water heater can make water hot enough to cause severe burns instantly, resulting in severe injury or death.

• Feel water before bathing or s howering

• To reduce the risk of scalding, install

Thermostatic Mixing Valves (temperature limiting valves) at each point-of-use. These valves automatically mix hot and cold water to limit the temperature at the tap. Mixing valves are available from your local plumbing supplier

. Follow manufacturer’s instructions for installation and adjustment of the valves.

• The User Interface Module (UIM) on this water heater has been factory set to approximately 120°F/60°C to reduce the risk of scalding. Higher temperatures increase the risk of scalding, but even at 120°F/60°C, hot water can scald. If you choose a higher temperature, Thermostatic

Mixing Valves located at each pointof-use are particularly important to help avoid scalding.

Temperature Time to Produce a

Serious Burn

120°F (49°C) More than 5 minutes

125°F (52°C) 1½ to 2 minutes

130°F (54°C) About 30 seconds

135°F (57°C) About 10 seconds

140°F (60°C) Less than 5 seconds

145°F (63°C) Less than 3 seconds

150°F (66°C) About 1½ seconds

155°F (68°C) About 1 second

For informa on about changing the factory thermostat se ng(s), refer to the “Adjus ng Temperature” sec on in this manual (“Step 12” on page 16).

Regardless of the water heater UIM se ng, higher temperatures may occur in certain circumstances:

• In some cases, repeated small draws of water can cause the hot and cold water in the tank to “stack” in layers. If this happens, the water can be as much as

30°F/15°C degrees hotter than the thermostat setting. This temperature variation is the result of your usage pattern and is not a malfunction.

• Water temperature will be hotter if someone adjusted the thermostat(s) to a higher setting.

• Problems with the thermostat(s), or other malfunctions may result in higher than expected water temperatures.

• If the water heater is in a hot environment, the water in the tank can become as hot as the surrounding air, regardless of the thermostat setting.

• If the water supplied to the water heater is pre-heated (for example, by a solar system) the temperature in the tank may be higher than the water heater’s thermostat setting.

To reduce the risk of unusually hot water reaching the fi xtures in the house, install Thermosta c Mixing

Valves at each point-of-use.

If anyone in your home is at par cular risk of scalding (for example, the elderly, children, or people with disabili-

es) or if there is a local code or state law requiring a certain water temperature at the hot water tap, then these precau ons are par cularly important.



According to a na onal standard

American Society of Sanitary Engineering (ASSE 1070) and most local plumbing codes, the water heater’s thermostat should not be used as the sole means to regulate water temperature and avoid scalds.

Properly adjusted Thermosta c Mixing

Valves installed at each point-of-use allow you to set the tank temperature to a higher se ng without increasing risk of scalds. A higher temperature se ng allows the tank to provide much more hot water and can help provide proper water temperatures for appliances such as dishwashers and washing machines.

Higher tank temperatures (140°F) also kill bacteria that cause a condi-

on known as “smelly water” and can reduce the levels of bacteria that cause water-borne diseases.

Water Contamination Risk

Do not use chemicals that could contaminate the potable water supply. Do not use piping that has been treated with chromates, boiler seal, or other chemicals.

Fire Risk

To reduce the risk of a fire that could destroy your home and seriously injure or kill people:

• D o not store things that can burn easily such as paper or clothes next to the water heater.

• Be sure the junction box cover and the element access door covers are in place. These covers keep debris from entering and potentially being ignited, and help keep any internal fires from spreading.

• Keep the water heater from becoming wet. Immediately shut the water heater off and have it inspected by a qualified person if you find that the wiring, thermostat(s) or surrounding insulation have been exposed to water in any way (e.g., leaks from plumbing, leaks from the water heater itself can damage property and could cause a fire risk). If the water heater is subjected to flood conditions or the thermostat(s) have been submerged in water, the entire water heater must be replaced.

• Make electrical connections properly, according to the instructions on page 15. Use 10 gauge solid copper wire. Use a UL listed or CSA approved strain relief. Connect ground wire to green ground screw.

Explosion Risk

High temperatures and pressures in the water heater tank can cause an explosion resulting in property damage, serious injury or death. A new Temperature and Pressure (T&P)

Relief Valve is included with your water heater to reduce risk of explosion by discharging hot water. Additional temperature and pressure protective equipment may be required by local codes.

A nationally recognized testing laboratory maintains periodic inspection of the valve production process and certifies that it meets the requirements for Relief Valves for Hot Water Supply

Systems, ANSI Z21.22. The T&P Relief

Valve’s relief pressure must not exceed the working pressure rating of the water heater as stated on the rating plate.

Maintain the T&P Relief Valve properly.

Follow the maintenance instructions provided by the manufacturer of the

T&P Relief Valve (label attached to T&P

Relief Valve) and the procedure on page 29.

An explosion could occur if the T&P

Relief Valve or discharge pipe is blocked. Do not cap or plug the T&P

Relief Valve or discharge pipe.

Fire and Explosion Risk if Hot Water is

Not Used for Two Weeks or More

CAUTION! Hydrogen gas builds up in a hot water system when it is not used for a long period (two weeks or more).

Hydrogen gas is extremely fl ammable.

If the hot water system has not been used for two weeks or more, open a hot water faucet for several minutes at the kitchen sink before using any electrical appliances connected to the hot water system. Do not smoke or have an open fl ame or other igni on source near the faucet while it is open.


GETTING STARTED

Figure 1 - Flexible connectors use compression fittings and do not require soldering.

Figure 2 - Use a non-contact circuit tester to insure that the power is off before you work on a circuit.

Figure 3 - Install a Pressure Reducing Valve set to 50 to 60 PSI.

Figure 4 - Condensate overflow flexible tubing.

Elbow

3/4” OD

Pipe

To Main

Drain Connection

3/4” ID

3/4” OD

1

Review all of the instruc ons before you begin work.

Improper installa on can damage the water heater, your home and other property, and can present risks of serious injury or death.

2

Check with your local and state authori es for any local or state codes that apply to your area. In the absence of local and

state codes, follow Na onal Fire

Protec on Associa on (NFPA-70) and the current edi ons of the Na onal

Electric Code (NEC ) and the Interna-

onal Plumbing Code (IPC). The instruc ons in this manual comply with na onal codes, but the installer is responsible for complying with local codes.

Massachuse s code requires this water heater to be installed in accordance with Massachuse s 248-CMR 2.00 and

248-CMR 5.00: State Plumbing Code.

Other local and state authori es may have similar requirements or other codes applicable to the installa on of this water heater.

3

Before you start, be sure you have, and know how to use, the following tools and supplies:

• Plumbing tools and supplies appropriate for the type of water pipes in your home

• Threaded connectors (Figure 1) for the cold and hot water pipes

• For homes plumbed with plastic pipe, use threaded connectors suitable for the specific type of plastic pipe used: CPVC and PEX (crosslinked polyethylene). Do not use

PVC pipe.

• For homes with copper pipes, you may purchase connector kits with compression fittings that don’t require soldering (Figure 1). Compression fittings are easier to install than soldering copper pipes.

Figure 5 - Main Drain Connection piping.


• Teflon® tape or pipe joint compound approved for potable water

• Tools to make the electrical connections (for example, screwdrivers, wire strippers)

• Non-Contact circuit tester to check for power (Figure 2)

• Water Pressure Gauge (Figure 6 on page 7)

Recommended Accessories:

• Suitable drain pan (Figure 8 on page

8)

• Automatic leak detection and shutoff device

• Pressure Reducing Valve (Figure 3 on page 6)

• Thermal Expansion Tank (Figure 7 on page 7)

• Point-of-use Thermostatic Mixing

Valves (Figure 9 on page 8)

• 1/2” Flexible tubing for Condensate

Overflow (Figure 4 on page 6)

• 90° Elbow with 3/4” Female

Unthreaded Socket End X 3/4”

Male NPT Threaded End (Figure 5 on page 6)

• 3/4” OD Plastic Pipe for Condensate

Drain (Figure 5 on page 6)

INSTALLATION

Follow these steps for proper

installa on:

Step 1:

✓

Verify that your home is equipped and up-to-date for proper opera on

Installing a new water heater is the perfect me to examine your home’s plumbing system and make sure the system is up to current code standards.

There have likely been plumbing code changes since the old water heater was installed. We recommend installing the following accessories and any other needed changes to bring your home up to the latest code requirements.

Use this checklist and inspect your home. Install any devices you need to comply with codes and assure that your new water heater performs at its best. for more informa on.

✓

Water pressure

We recommend checking your home’s water pressure with a pressure gauge (Figure 6). Most codes allow a maximum incoming water pressure of 80 psi/550 kpa. We recommend a working pressure no higher than 50-60 psi/345-414 kpa.

HOW: Purchase an inexpensive water pressure gauge available at your local plumbing supplier . Connect the Water

Pressure Gauge to an outside faucet and measure the maximum water pressure experienced throughout the day (highest water pressures o en occur at night).

✓

Water Pressure/

Thermal Expansion

Verify that you have a properly sized

Thermal Expansion Tank (Figure 7). We recommend installing an expansion tank if your home does not have one.

Codes require a properly pressurized, properly sized Thermal Expansion Tank in almost all homes. (See illustra on on inside front cover.)

Figure 6 - Use a Water Pressure Gauge to make sure your home’s water pressure is not too high.

To limit your home’s water pressure:

Locate your home’s Pressure Reducing Valve (PRV) on the main incoming

(cold) water supply line and adjust the water pressure control to between

50 and 60 psig. If your home does not have a Pressure Reducing Valve, install a PRV on the home’s main water supply line and set it to between 50 and 60 psig. Pressure Reducing Valves are available at your local plumbing supplier

.

BACKGROUND: Over the years, many u li es have increased water supply pressures so they can serve more homes. In some homes today, pressures exceed 100 psig. High water pressures can damage water heaters, causing premature leaks. If you have replaced toilet valves, had a water heater leak, or had to repair appliances connected to the plumbing system, pay par cular a en on to your home’s water pressure. When purchasing a

PRV, make sure the PRV has a built-in bypass.

Figure 7 - A Thermal Expansion Tank helps protect the home’s plumbing system from pressure spikes.

HOW: Connect the Thermal Expansion

Tank (available at your local plumbing supplier

) to the cold water supply line near the water heater. The expansion tank contains a bladder and an air charge. To work properly, the Thermal

Expansion Tank must be sized according to the water heater’s tank capacity and pressurized to match the home’s incoming water pressure. Refer to the installa on instruc ons provided with the Thermal Expansion Tank for installa on details.


INSTALLATION

BACKGROUND: Water expands when heated, and the increased volume of water must have a place to go, or thermal expansion will cause large increases in water pressure (despite the use of a Pressure Reducing Valve on the home’s main water supply line). The Safe Drinking Water Act of

1974 requires the use of backfl ow preventers and check valves to restrict water from your home reentering the public water system. Backfl ow preventers are o en installed in water meters and may not be readily visible.

As a result, most all plumbing systems today are now “closed,” and almost all homes now need a Thermal Expansion Tank.

A Thermal Expansion Tank is a prac cal and inexpensive way to help avoid damage to the water heater, washing machine, dishwasher, ice maker and even toilet valves. If your toilet occasionally runs for no apparent reason (usually briefl y at night), that may be due to thermal expansion increasing the water pressure temporarily.

✓

Water pipe and tank leaks

Leaks from plumbing pipes or from the water heater itself can damage property and could cause a fi re risk.

• Install an automatic leak detection and shutoff device (available at your local plumbing supplier).

These devices can detect water leaks and can shut off the water heater’s water supply if a leak occurs.

Figure 8 - A suitable drain pan piped to an adequate drain can help protect flooring from leaks and drips.

• Install a suitable drain pan (available at your local plumbing supplier) under the water heater (Figure

8) to catch condensation or leaks in the piping connections or tank.

Most codes require and we recommend installing the water heater in a drain pan that is piped to an adequate drain. The drain pan must be at least 2”/50mm wider than the diameter of the water heater.

Install the drain pan so the water level would be limited to a maximum depth of 1-3/4”/45mm.

✓

Water temperature regula on

Figure 9 - Thermostatic Mixing Valves installed at each point-of-use can help prevent scalds.

Install Thermosta c Mixing Valves

(Figure 9) to regulate the temperature of the water supplied to each pointof-use (for example, kitchen sink, bathroom sink, bath, shower). Consult the valve manufacturer’s instruc-

ons or a qualifi ed person.

WARNING! Even if the water heater thermostat is set to a rela vely low temperature, hot water can scald.

Install Thermosta c Mixing Valves at each point-of-use to reduce the risk of scalding (page 4).

BACKGROUND: A Thermosta c Mixing Valve, installed at each pointof-use, mixes hot water from the water heater with cold water to more precisely regulate the temperature of hot water supplied to fi xtures. If you aren’t sure if your plumbing system is equipped with properly installed and adjusted Thermosta c Mixing

Valves at each point where hot water is used, contact a qualifi ed person for more informa on.

Step 2:

Verify that the loca on is appropriate

Before installing your water heater, ensure that:

The water heater will be:

1

• Installed indoors close to the center of the plumbing

system.

• In a suitable drain pan piped to an adequate floor drain or external to the building (Figure 8).

• In an area that will not freeze

• In an area that is suitable for installing the water heater vertically and on a level surface.

• Install where a typical home appliance sound would not cause a disturbance

• Should not be used for space heating.


INSTALLATION

2

The loca on has adequate space (clearances) for periodic servicing. For op mal water unrestricted airfl ow and requires a minimum installa on space of 700 cubic feet. As an example, a room that has an 8 foot tall ceiling and is 10 feet long by 8-3/4 feet wide would contain

700 cubic feet.

NOTICE: This Heat Pump Water Heater may be located within a required minimum of 6” clearance from a wall on the outlet side, however for future service considera ons, a minimum of

3 feet from any obstruc on on the back, le and right side is recommended.

3

The fl oor can support the weight of a full water heater.

Table 1

Capacity Filled Weight (lbs)

50 Gallon

66 Gallon

80 Gallon

573

796

921

4

Your area is not prone to earthquakes. If it is, use special straps as required by local building codes.

NOTICE! The state of California requires bracing, anchoring, or strapping the water heater to avoid its moving during an earthquake. Contact local u li es for code requirements in your area, visit h p://www.dsa.dgs.ca.gov, or call 1-916-445-8100 and request instruc ons. Other loca ons may have similar requirements. Check with your local and state authori es.

5

The loca on is not prone to physical damage by vehicles, fl ooding, or other risks.

Vehicle

Stop

Drain

Pan

Drain

Figure 10 - In a garage, install a vehicle stop to avoid water heater damage.

6

Avoid loca ons such as a cs, upper fl oors, or where a leak might damage the structure or furnishings. Due to the normal corrosive ac on of water, the tank will eventually leak. To minimize property damage from leaks, inspect and maintain your water heater in accordance with this manual’s instruc ons.

Inspect the drain pan, pipes, and surrounding area regularly and fi x any leaks found. Drain pans are available at your local plumbing supplier

. Leaks are frequently in the plumbing system itself and not the water heater.

7

The unit cannot be placed into any type of closet or small enclosure, unless adequate provisions are made for air exchange

(vented or louvered doors, etc.).

To ensure op mal perfor-

8

mance and servicability, a minimum clearance of 6 inches must be maintained from all sides and 6 inches from the top for access to the air fi lter.

Water heaters located in

9

uncondi oned spaces (i.e., garages, basements etc.) may require the water piping, condensate piping, and drain piping to be insulated to guard from freezing.

10

The air fi lter, condensa on drain and controls must be easily accessable for opera-

on and service.

11

The site loca on must be free from any corrosive elements in the atmosphere such as sulfer, fl uorine, sodium and chlorine. These elements are found in aerosol sprays, detergents, bleaches, air fresheners, paint and varnish removers, refrigerants and many other household products. In addi on, excessive dust and lint may eff ect the opera on of the unit, see the Air Filter

Maintenence sec on in this manual.

12

The ambient air temperature must also be considered when

Mode the air temperature needs to be above 45°F/7°C and below 120°F/48°C for heat pump opera on. If the air temperature falls outside these upper and lower limits, the electrical elements will ac vate to meet the hot water demand and the heat pump does not

Mode.


INSTALLATION

Step 3:

Removing the old water heater

1

Read each installa on step and decide if you have the necessary skills to install the water heater. Only proceed if you can safely perform the work. If you are not comfortable, have a qualifi ed person perform the installa on.

Locate the water heater’s

2

circuit breaker and turn it

OFF (or remove the circuit’s fuses).

3

On the old water heater, remove the electrical junction box access panel.

Using a non-contact circuit tester, check the wiring to make certain the power is OFF.

WARNING! Working on an energized circuit can result in severe injury or death from electrical shock.

4

Disconnect the electrical wires.

5

Open a hot water faucet and let the hot water run un l it is cool (This may take 10 minutes or longer).

WARNING! Be sure the water runs cool before draining the tank to reduce the risk of scalding.

6

Connect a garden hose to the drain valve and place the other end of the hose in a drain, outside, or a bucket. (Note that sediment in the bo om of the tank may clog the valve and prevent it from draining. If you can’t get the tank to drain, contact a qualifi ed person.)

7

Turn the cold water supply valve OFF.

8

Open the drain valve on the water heater.

Figure 12 - Draining the old water heater.

9

Also open a hot water faucet to help the water in the tank drain faster.

10

When the tank is empty, disconnect the Temperature &

Pressure (T&P) Relief Valve discharge pipe. You may be able to reuse the discharge pipe, but do not reuse the old T&P Relief Valve. A new

T&P Relief Valve comes installed on your water heater (or on some models, is in the carton with the water heater).

Figure 13 - Removing the T&P Relief Valve discharge pipe.

11

Disconnect the water pipes.

Many water pipes are connected by a threaded union which can be disconnected with wrenches. If you must cut the water pipes, cut the pipes close to the water heater’s inlet and outlet connec ons, leaving the water pipes as long as possible. If necessary, you can make them shorter later when you install the new water heater.

12

Remove the old water heater.

WARNING! Use two or more people to remove or install water heater.

Failure to do so can result in back or other injury.

Figure 11 - Let the hot water run until it is cool.


INSTALLATION

Step 4:

Installing the new water heater

1

Completely read all instruc-

ons before beginning. If you are not sure you can complete the installa on, DO NOT RETURN THIS

UNIT TO THE STORE. Seek assistance from any of the following sources:

• Schedule an appointment with a qualified person to install your water heater.

• Call our Technical Assistance Hotline at

1-800-821-2017

2

3

Install a suitable drain pan that is piped to an adequate drain.

Set the water heater in place taking care not to damage the drain pan.

NOTICE! Most codes require se ng the water heater in a suitable drain pan piped to an adequate drain. The drain pan helps avoid property damage which may occur from condensa on or leaks in the piping connec ons or tank.

The drain pan must be at least two inches wider than the diameter of the water heater. Install the drain pan so the water level is limited to a maximum depth of 1-3/4” (45mm).

4

Verify that the water heater is set in place properly. Check that:

• The T&P Relief Valve will not be in contact with any electrical parts.

• There is adequate space to install the T&P Relief Valve discharge pipe and that it can be piped to a separate drain (and not into the drain pan).

• There is adequate space to install proper condensate drain piping.

• There is adequate access and space around the water heater for future maintenance. A minimum clearance of 6 inches must be maintained from all sides and 6 inches from the top for access to the air filter.

• Unit is level to allow proper condensate drainage. An unlevel unit may lead to condensate draining inproperly and resulting in property damage.

DO NOT CONNECT ELECTRICAL

WIRING UNTIL YOU ARE

INSTRUCTED TO DO SO.

NOTICE! Connec ng electrical power to the tank before it is completely full of water (water must run FULL

STREAM from a hot water tap for a full three minutes) will cause the upper hea ng element to burn out.

Step 5:

Connec ng the Condensate Pump When Required

NOTE: If no fl oor drain is available or the drain is above the level of the condensate line, a condensate pump must be installed.

1

Follow condensate drain pump manufacturers instruc-

ons for installa on.

Connec ng the Condensate Pump Op onal

Overfl ow Shut Off

Switch

1

Locate the wiring behind the condensate drain access cover by removing the 4 screws a aching the cover to the unit. Cut the loop and strip insula on off the 2 ends

(Figures 14 & 15 on pages 11 & 12).

Measure the distance from

2

the condensate drain access cover to the condensate pump, and cut two 22 AWG wires to correct length and strip the insula on at both ends. Thread both ends through the grommet on the drain pan cover.

3

Connect these 2 wires to the

2 wires on the water heater using wire nuts or other connectors. Reinstall the condensate drain access cover and keep the connec on joints inside of the cover.

4

Connect the free ends of the

2 wires to the shut off switch on the condensate pump in accordance with the condensate pump manufacturers recommenda ons.

Condensate Pump Wiring Loop

(Loop Located Close to the Drain Connections)

Wires From

Water Heater

Wires to Condensate

Pump Overflow

Shut Off Switch

Figure 14 - Wiring Loop for connec on of

Condensate Pump.


INSTALLATION

Condensate Drain

Access Cover

Primary Drain

Connection

Secondary Drain

Connection

Overflow Slot

Condensate Pump Wiring

(Loop Located Close to the Drain Connections)

Figure 15 - Condensate Pump Wiring

Step 6:

Install Condensate

Drain Lines:

NOTE: When making condensa on connec ons to the primary connec-

on DO NOT over ghten! These connec ons should be HAND TIGHTENED

ONLY. Over ghtening could crack or damage the condensate drain pan.

• Plas c pipe or tubing must be used to connect the condensate drain to a suitable drain or condensate pump.

• Condensate drain lines should be installed in condi oned areas only. Install approved insula on on the condensate drain lines to prevent condensa on from forming on the outside of the drain lines. Condensa on drain lines installed in areas that are subject to freezing temperatures should be wrapped with a na onally recognized heat tape. Install per manufacturer’s instruc ons.

• Do not connect condensate drain lines with other drain or discharge lines into a single (common) pipe or line. Each line (condensate drain line, temperature and relief valve discharge pipe, etc.) should be independently run to an adequate drain.

• Slope the condensate drain lines toward the inside fl oor drain or condensate pump.

• The condensate drain lines and connec ons to the drain piping must comply with all local codes.

primer to cement the condensate drains to the heat pump drain pan.

• If a condensate pump is installed, it should be wired to shut off the heat pump in the event the condensate pump fails or the fl oat switch in the pump ac vates (see step 5 on page 11).

1

Using 3/4” PVC piping, a 90° elbow that is 3/4” slip & 3/4”

NPT and an approved sealant

(none supplied with unit), a ach the elbow to the primary drain connec-

on and insert the PVC pipe into the female end allowing enough length to access an adequate drain.

2

Using 1/2” ID rubber or fl exible plas c tubing, slip one end over the secondary drain connec on allowing enough length to access an adequate drain.

Step 7:

Connect the Temperature and Pressure (T&P)

Relief Valve/Pipe

Most T&P Relief Valves are preinstalled at the factory. In some cases, they are shipped in the carton and must be installed in the opening marked and provided for this purpose and according to local codes. .

WARNING! To avoid serious injury

or death from explosion, install a T&P

Relief Valve according to the following instruc ons:

If your water heater does not have a factory installed T&P Relief Valve, install the new T&P Relief Valve that came with your water heater. Do not reuse an old T&P Relief Valve. Install a T&P Relief Valve discharge pipe according to local codes and the following guidelines:

1

The discharge pipe should be at least 3/4” inside diameter and sloped for proper drainage. Install it to allow complete drainage of both the T&P Relief Valve and the discharge pipe.

2

The discharge pipe must withstand 250°F (121°C) without distor on. Use only copper or CPVC pipe. Most homes use copper water pipes, but some use

CPVC or cross-linked polyethylene

(PEX). Use fi ngs appropriate for the type of pipe in your home. Do not use any other type of pipe, such as PVC, iron, fl exible plas c pipe, or any type of hose.

Figure 16 - The T&P Relief Valve discharge pipe must be installed properly and piped to an adequate drain.


INSTALLATION

3

Terminate the discharge pipe a maximum of six inches above a fl oor drain or outside the building. Do not drain the discharge pipe into the drain pan; instead pipe it separately to an adequate drain. In cold climates, terminate the discharge pipe inside the building to an adequate drain. Outside drains could freeze and obstruct the drain line.

Protect the drain from freezing.

DISCHARGE

PIPE

DRAIN

PIPE valves that are compa ble with potable water. Use only full-fl ow ball or gate valves. Other types of valves may cause excessive restric on to the water fl ow.

2

Install a Thermosta c Mixing

Valve at each point-of-use (for example, kitchen sink, bathroom sink, bath, shower). Consult the valve manufacturer’s instruc ons or a qualifi ed person.

Figure 17 - The end of the T&P Relief Valve discharge pipe must stop no more than six inches above a floor drain or outside.

4

Do not place any valve or other restric on between the tank and T&P Relief Valve. Do not cap, block, plug, or insert any valve between the T&P Relief Valve and the end of the discharge pipe. Do not insert or install any reducer in the discharge pipe.

Step 8:

Install shutoff and mixing valves

1

If one is not already installed, install a manual shutoff valve in the cold water line that supplies the water heater. Install the shutoff valve near the water heater so that it is readily accessible. Only use

Figure 18 - Install Thermostatic Mixing

Valves at each point where hot water will be used.

WARNING! Even if the water heater’s thermostat(s) are set to a rela vely low temperature, hot water can scald. Install Thermosta c Mixing

Valves at each point-of-use to reduce the risk of scalding.

3

For water heaters that are fed by a solar water hea ng system (or any other pre-heating system), always install a Thermosta c Mixing Valve or other temperature limi ng device in the inlet water supply line to limit water supply inlet temperature to 120°F. Solar water hea ng systems can supply water with temperatures exceeding 170°F and may result in water heater malfunc on.

WARNING! Hot water provided by solar hea ng systems can cause severe burns instantly, resul ng in severe

injury or death (page 4).

Step 9:

Connect the water supply

1

Determine the type of water pipes in your home. Most homes use copper water pipes, but some use CPVC or cross-linked polyethylene (PEX). Use fi ngs appropriate for the type of pipe in your home. Do not use iron or PVC pipe – they are not suitable for potable water.

2

Connect the cold water supply using 3/4 inch Na onal Pipe

Thread “NPT” to the blue cold water connec on near the bo om of the heater.

For ease of removing the water heater for service or replacement, connect the water pipes with a coupling called a union. We recommend using a dielectric-type union (available at your local plumbing supplier ). Dielectric unions can help prevent corrosion caused by tiny electric currents common in copper water pipes and can help extend the life of the water heater.

Recircula ng Loop

In order to optimize efficiency of this unit, it is not recommended for use with a recirculation loop. Using this in a recirculation loop may cause the unit to run excessively.


INSTALLATION

IF YOU HAVE COPPER PIPES:

If your home has copper water pipes, you can solder the water pipe connec-

ons or use compression fi ngs which don’t require soldering. Compression fi ngs are easier to install than soldering pipe. Check with local plumbing pipe materials are suitable for your loca on. Do not use lead-based solder.

NOTICE: This water heater model contains an outlet connec on (J-tube) that has an orienta on mark that must line up with arrow (in a 12 o’clock posi on).

3

Connect the hot water supply using 3/4 inch NPT to the hot water outlet. Follow the same connec on guidelines as for the cold water supply.

4

Install insula on (or heat tape) on the water pipes especially if the indoor installa on area is subject to freezing temperatures.

Insula ng the hot water pipes can

NOTICE! Do not solder pipes while they are a ached to the water heater.

The water heater’s inlet and outlet connec ons contain non-metallic parts which could be damaged. The proper way to connect the water heater to copper water pipes is as follows:

• Solder a short length of pipe (about a foot or so) to a threaded adapter using only 95/5 n-an mony or equivalent solder. A ach the threaded adapters to the water heater’s connec ons (using Tefl on® tape or pipe joint compound). Connect the home’s water pipes by soldering, keeping the connec ons at the water heater cool with wet rags.

NOTE: Do not over apply joint compound.

5

Double check to make sure the hot and cold water pipes are connected to the correct hot and cold water fi ngs on the water heater.

6

If needed, install (or adjust) the home’s Pressure Reducing

Valve to 50-60 psig and install a Thermal Expansion Tank.

Figure 19 - A Pressure Reducing Valve is required if your home’s water pressure is above 80 psi.

Figure 20 - The Thermal Expansion Tank should be pressurized with air, to match the home’s incoming water pressure.

Step 10:

Verify connec ons and completely fi ll tank

To remove air from the tank and allow the tank to fi ll completely with water, follow these steps:

1

Remove the aerator at the nearest hot water faucet. This allows any debris in the tank or plumbing system to be washed out.

Turn the cold water supply

2

back on.

Full-fl ow ball valve

Figure 21 - Fully open the cold water supply valve.


INSTALLATION

3

4

5

Open a hot water faucet and allow the water to run un l it fl ows with a full stream.

Let the water run full stream for three full minutes.

Close the hot water faucet and replace the aerator.

6

Check inlet and outlet connec-

ons and water pipes for leaks.

Dry all pipes so that any drips or leaks will be apparent. Repair any leaks. Almost all leaks occur at connec-

ons and are not a tank leak.

Step 11:

Make electrical connec ons

WARNING! Working on an energized circuit can result in severe injury or death from electrical shock.

NOTICE! Do not turn electrical power on unless you are sure all of the air is out of the tank and the tank is completely full of water. Although this water heater is equipped with “Dry Fire” protec on, be certain all air is purged from the tank before making any electrical connec ons.

Be sure the electrical power to

1

the water heater is turned OFF at the circuit breaker panel (or remove the circuit’s fuses).

2

Using a non-contact circuit tester, check the wiring to make certain the power is OFF.

3

This water heater requires a

240/208 VAC single phase 30 amp power supply, at 60Hz.

Check the water heater’s data plate

(see fi gure 23 on page 15) and ensure that the home’s voltage, wiring size

(ampacity) and circuit breaker ra ng and type are correct for this water heater. Refer to the wiring diagram located on the water heater for the correct electrical connec ons. Ensure that wire sizes, type, and connec ons comply with all applicable local codes.

In the absence of local codes, follow

NFPA-70 and the current edi on of the

Na onal Electric Code (NEC).

Power Supply

Connector

1/2” Conduit

Opening

Green Ground

Screw

Green

Ground

Wire

Red Wire

Black Wire

Figure 22 - Connecting the electrical wires.

If metal conduit is used for the grounding conductor:

• The grounding electrode conductor shall be of copper, aluminum, or copperclad aluminum. The material shall be of one con nuous length without a splice or joint.

• Rigid metal conduit, intermediate metal conduit, or electrical metallic tubing may be used for the grounding means if conduit or tubing is terminated in fi ngs approved for grounding.

• Flexible metal conduit or fl exible metallic tubing shall be permi ed for grounding if all the following condi ons are met:

A. The length in any ground return path does not exceed 6 feet.

B. The circuit conductors contained therein are protected by overcurrent devices rated at 30 amperes.

C. The conduit or tubing is terminated in fi ngs approved for grounding.

For complete grounding details and all allowable excep ons, refer to the current edi on of the Na onal Electric

Code NFPA 70.

Figure 23 - The water heater’s electrical requirements can be determined from the data plate.

4

Remove the cover on the electrical junc on box on the side of the water heater.

5

Install wiring in an approved conduit (if required by local codes). Use a UL listed or CSA approved strain relief to secure the electrical wiring to the water heater.

6

Connect the ground wire to the green ground screw.

Connect the home’s two power wires to the water heater’s two power wires. Use suitable wire nuts or other approved means to make the power connec ons.

7

Replace the junc on box cover and secure with the screw provided.

WARNING! Be sure cover is secured

to reduce the risk of fi re and electric shock.


INSTALLATION

Operation

The water heater is now ready for normal operation. To keep your water heater working safely and efficiently and extend its life, perform maintenance as described in maintenance section beginning on page 26.

Start-up and Opera on

NOTE: The default opera ng mode is

Hybrid, to select a diff erent mode see

“Opera ng Mode Descrip ons” sec on on page 17.

PRIOR TO BEGINNING OPERATION:

Air fi lter is factory installed with tabs oriented down for shipping. Please see maintenance sec on for instruc ons on removal, cleaning and replacing.

1

Turn on electrical power to the water heater.

NOTICE: The water heater will conduct a system diagnos c (approximately 8 minutes) each me power is applied from an off state. Normal opera on will begin a er the system diagnos c has been completed..

2

Once the diagnos c sequence has fi nished, the fan should turn on. This typically takes 8 minutes, (the User Interface Module will display “-”, “--”, “---” repe vely during this period).

NOTICE: The heat pump’s fan will not turn on if the incoming water temperature is less than 59°F/15°C and/or the ambient air temperature is above

120°F/15°C, or below 45°F/7.2°C.

Should the internal diagnos cs detect a problem with the heat pump, an error code will be displayed.

3

Set the desired opera onal mode. For typical installa ons, the factory default mode,

Hybrid Mode off ers the best combina-

Figure 24 -

Adjust Thermostat Mixing

Valves at each point-of-use 120°F or

For detailed descrip ons of all opera-

onal modes see “Opera ng Mode

Descrip ons” page 17.

Step 12:

Adjus ng the

Temperature

With the installa on steps completed, you may adjust the water heater’s temperature se ng if desired.

1

The water heater’s temperature se ng has been factory set to approximately 120°F to reduce the risk of scald injury. You may wish to set a higher temperature to provide hot water for automa c dishwashers or laundry machines, to provide more hot water capacity, and to reduce bacterial growth. Higher tank temperatures (140° F) kill bacteria that cause a condi on known as “smelly water” and can reduce the levels of bacteria that cause water-borne diseases.

WARNING! Higher temperatures in-

crease the risk of scalding, but even at

120°F, hot water can scald (page 4).

If you increase the water heater’s temperature se ng, install Thermosta c

Mixing Valve(s) at each point-of-use to reduce the risk of scalding. lower.

To adjust the water heater’s temperature se ng:

• The water temperature setting can be adjusted by using the Up and Down buttons on the UIM (User Interface Module).

Using the up or down buttons, cycle through the available temperature set points until the desired temperature is displayed. The temperature setting will blink on the display; press the Mode/Enter button to confirm the selection (see figure 26 on page 19).

• The available temperature set points can be cycled through quickly by pressing and holding the Up button.

2

Please allow adequate me for the heater to provide hot water.

WARNING! If you have increased

the temperature se ng and the

Thermosta c Mixing Valves are not set properly (or not installed) you could scald yourself while checking the temperature.

3

Check water temperature at several points of use in your home (for example, bathtub faucet, shower, or lavatory sink) and adjust the Thermosta c Mixing Valves as needed. If you aren’t sure how to adjust the Thermosta c Mixing Valve se ngs, or aren’t sure if you have

Thermosta c Mixing Valves, contact a qualifi ed person.


INSTALLATION

Post Installa on Review

1

Understand how to use the

User Interface Module to set the various modes and func ons.

2

Hybrid Mode is the recommended Opera ng Mode.

Understand the various

Opera ng Modes and which mode may be best, based on ambient temperature and hot water demands.

3

Understand the importance of rou ne inspec on/ maintenance of the condensate drain pan and lines. This is to prevent any possible drain line blockage resul ng in the condensate drain pan overfl owing.

NOTE: If water is coming from the overfl ow slot of the condensate drain access cover, this indicated that both condensate drain lines may be blocked and immediate ac on is required.

Drain Access Cover

Secondary Drain

Primary Drain

Overflow Slot

Figure 25 - Condensate Drain Access

Cover

4

To maintain op mal opera on, check, remove and clean the air fi lter as needed.

5

The Installa on Instruc ons and Use and Care Guide should be kept with the water heater for reference.

Water Temperature Adjustment

The water temperature can be adjusted from 95°F / 35°C to 150°F /

65.5°C. Use the Up and Down Bu ons

on the front panel to set the desired temperature (fi gure 26, page 19). The se ng temperature will blink on the display, press Mode/Enter bu on to confi rm.

The water temperature can be adjusted quickly by pressing the

“Temperature Up” bu on and holding for three seconds.

NOTE: Before a emp ng to adjust the thermostat, read the “Water

Temperature Regula on” sec on. If the instruc ons are not clear, contact a qualifi ed person.

NOTE: For increased water demand, switching (temporarily) to Hybrid

Mode or Electric Mode will decrease the recovery/re-heat me. Be sure to switch back to the desired opera onal mode when fi nished.

Opera ng Mode Descrip ons

The opera ng modes can be changed sequen ally by pressing the Mode/

Enter bu on (Figure 26, page 19). The

Opera on Mode Indica on Light will turn on when the relevant mode is selected.

This unit is equipped with technology that senses the hot water demand

Hybrid mode, during normal usage, the unit will operate the heat pump mode during periods when the water usage is above normal, this unit has the ability to use one element

(upper or lower) and the heat pump simultaneously to help improve recovery. This transi on is seamless and will go unno ced.

Efficiency Mode -

Provides the highest efficiency and lowest cost operation by using only the heat pump for heating. Recovery time and efficiency will vary with ambient temperature and relative humidity. Efficiency will be greatest, and recovery quickest, when both are high. At lower temperatures and relative humidity levels, efficiency will be lower and recovery will take longer. Heat pump operation is allowed between 45°F / 7.2°C to 120°F / 48.8°C ambient temperature. At ambient temperatures lower than 45°F / 7.2°C and greater than 120°F / 48.8°C, the heat pump will not operate. Similarly, if the water temperature in the tank is less than 59°F / 15°C, the heat pump will not operate. The unit will operate in electric mode until ambient air and water temperatures return to the safe operating range of the heat pump.

Hybrid Mode -

This is the default, recommended setting, combining high energy efficiency with reduced recovery time.

This mode uses the heat pump as the primary heating source. One of the heating elements (upper or lower) will provide supplementary heating if demand exceeds a predetermined level so that the set point temperature can be recovered more quickly.


INSTALLATION

Electric Mode -

The water heater functions as a conventional electric unit, relying on only the elements for heat. This mode may be useful in periods of increased hot water demands. Electric Mode will remain for 48 hours before reverting back to default mode setting.

Vacation Mode -

The controller will maintain a 60°F tank temperature while in Vacation setting. This mode is recommended when the water heater is not in use for a long period of time, to minimize energy consumption and prevent the water heater from freezing during cold conditions.

To enter Vacation Mode -

Press and hold the up ↑ button. If selected, the unit will default to 7 days, but you will be able to adjust the number of days by pressing the up ↑ and down ↓ arrows; press the Mode/

Enter button to confirm the number of days. When set time for Vacation Mode has completed, UIM will automatically return to last mode selected.

C AUTION! Hydrogen gas builds up in a hot water system when it is not used for a long period (two weeks or more).

Hydrogen gas is extremely fl ammable.

If the hot water system has not been used for two weeks or more, open a hot water faucet for several minutes at the kitchen sink before using any electrical appliances connected to the hot water system. Do not smoke or have an open fl ame or other igni on source near the faucet while it is open.

NOTE: When Vacation Mode is selected, the vacation timer will be displayed. Press the Up and Down button to modify the timer to desired number of vacation days (setting range: 1 to

99 days). The vacation timer will blink on the display; press the Mode/Enter button to confirm the vacation timer.

To deactivate Vacation Mode, press the

Mode/Enter button to switch to the desired mode.

NOTE: Do not shut off power to the unit for extended periods of time.

If power must be turned off for an extended period of time, drain the tank completely.

Other Controls

°F/°C Switch - Press “Temperature

Down” button and hold for 3 seconds to switch temperature unit between

Farenheit and Celsius

Remote Access Enable/Disable:

• Press “Mode/Enter” button and hold for 3 seconds. The power saver feature will be activated and the display will show “rA”, and the setting temperature alternatively.

This feature allows the unit to be monitored and controlled using the Connectivity Port and a seperate control module.

• To deactivate Remote Access, press “Mode/Enter” button and hold for 3 seconds.

Heat pump defrosting indication:

• There will be frost accumulating on the evaporator when the heat pump is operated under low ambient temperatures. The controller will order the unit to enter into defrosting cycle to optimize the heat pump operation performance. During the defrosting period, the user interface module will display “ICE” as an indication.

Out of heat pump operation range:

• The user interface module will display “HPO” as an indication that the ambient and/or water temperature condition is out of the heat pump operation range.

NOTE: The display will go into “Sleep

Mode” for energy saving if there is no operation on any button for 15 minutes. All the display and lights will be turned off except for the “Operational

Mode Indication Light”, which will remain illuminated while the unit is powered on. The unit can be awakened by pressing any button.

Your Heat Pump Water Heater is Smart

Grid capable. Contact your local electric utilities company for participation and plug in module availability and to learn more about potential energy savings opportunities.


INSTALLATION

Display Segment

Temperature Unit

Indication Light

°F

°C

DAYS

Temperature Up

(Increase) Button

Temperature Down

(Decrease) Button

Mode/Enter

Button

Operational Mode

Indication Light

Temperature and

Pressure Relief Valve

1/2” Flexible

Secondary

Condensate

Tubing

Discharge Pipe

(Do Not Cap or Plug)

Metal Drain Pan 2 1/2”

Depth Maximum and

2 Inches wider than the water heater.

xxxxx xxxxx xxxxx xxxxx

Vacation Time Indication

Figure 26 - User Interface Module (UIM) Display

Massachusetts: Install a vacuum relief in cold water line per section 19 MGL 142.

Cold

(Inlet)

*Union

Hot

(Outlet)

*Union

Optional Heat Trap Piping

Union

Shut-off Valve (Hot)

Untempered Water Outlet

**Optional Mixing Valve - Follow the

Mixing Valve’s Manufacturer’s Installation

Instructions. (Set to 120°F / 48.8°C)

Tempered Water to Fixtures

Vacuum Relief Valve

(when required by local code)

Cold Water

Inlet Valve

Cold Water

Inlet

Pressure Reducing Valve (PRV) should be installed where the water supply enters the residence.

When installed PRVs create a closed water system, a thermal expansion tank must be installed.

***Primary Condensate Drain (3/4” PVC)

Union

In a closed system, use a thermal expansion tank.

See “Water Pressure/

Thermal Expansion” section.

Drain Line 3/4”

ID Minimum

Drain

6” Maximum

Air Gap

Shut-off Valve

(Cold)

*If copper piping is used, unions must be dielectric at inlet and outlets.

**Use a heat trap when installing a mixing valve near the water heater.

*** If an adequate drain is not available for the condensate drain lines then a condensate pump must be used. DO NOT discharge the condensate drain

lines into the metal drain pan.

Figure 27 - Completed Water System Piping


DIAGNOSTIC CODES

WARNING! Electric Shock Hazard; Disconnect power before servicing. Do not remove the plas c guard from over wiring. Do not

touch electrical wiring. Failure to do so can result in death or electrical shock.

*

DISPLAY SHOWS

- -- --- (series of dashes)

ICE

HPO

EUC

ELC

SF

INDICATES

Unit is doing a system diagnostic.

Heat pump is in defrosting cycle.

Ambient temperature <45°F or >120°F, average tank temperature of 59°F or less.

Upper element is not functioning

Lower element is not functioning

The air filter is dirty.

CORRECTIVE ACTION

Normal operation--no action

Refer to Page 22, Step 2 “Check Upper Heating Element.” and

Page 27 “Replacing the Heating Element”

Refer to Page 22, Step 2 “Check Upper Heating Element.” and

Page 27 “Replacing the Heating Element”

Refer to “Air Filter Maintenance” page 30.

*

*

*

*

*

ECF

E20 or E21

E30 or E31

E50 or E51

E10 or E11

E40 or E41

E60

Edr

EPL

EDH

The heat pump compressor is starting/stopping frequently.

1. If compressor is running and fan is not operating, call residential technical support.

2. Clean the air filter. See “Air Filter Maintenance” section on page 30.

3. Check installation location against recommended confined space requirements (step 2, page 9).

Upper Temperature Sensor is not functioning.

Lower Temperature Sensor is not functioning.

Heat Pump Suction Temperature

Sensor is not functioning.

Heat Pump Coil Temperature

Sensor is not functioning.

Heat Pump Discharge

Temperature Sensor is not functioning.

Upper and Lower Temperature

Sensor are not functioning

Power off (Power Cycling the unit, page 25), disconnect and reconnect J2 and J5 connections from control board, inspect wire for damage, re-install UIM, reconnect power. If error persists, replace temperature sensor.

Not enough water in the tank

(tank not full).

Open all hot water taps in home and run until water

(uninterrupted) flows from all open hot water taps.

Power supply voltage is too low.

Check for loose electrical connections, refer to “Power

Cycling the Unit”, page 25

Compressor Discharge

Temperature is too high.

Call Residential Technical Support

NOTE: The diagnostic codes listed above are the most common. If a diagnostic code not listed above is displayed, contact Residential

Technical Support referencing the number on the front of this manual.

*

There may be an audible alarm associated with this error. To cancel the audible alarm, press any bu on on the UIM.


DIAGNOSTIC CODES

WARNING! Electric Shock Hazard; Disconnect power before servicing. Do not remove the plas c guard from over wiring. Do not

touch electrical wiring. Failure to do so can result in death or electrical shock.

*

*

*

EoF

ECL

EEE

ECC

ECE

Condensate management

Heat pump suction pressure is too low.

EEPROM failure

Heat pump compressor is not functioning

Power supply error.

1. Ensure unit is installed level.

2. Check for blocked primary or secondary condensate drain lines, clear drain lines as necessary.

3. If an accessory condensate pump was installed: Turn off power to the water heater at the breaker and check control wire connections to condensate pump. See “Connecting

Condensate Pump” page 11.

4. Check to see if the accessory condensate pump is plugged in and has power.

5. Ensure the pump is operating properly, check pump outlet tube for blockage. for further assistance.

6. Repair or replace accessory condensate pump as necessary.

7. If probllem persists, call our Technical Assistance Hotline at 1-800-821-2017

Call our Technical Assistance Hotline at 1-800-821-2017 for further assistance.

1. Power cycle unit, see page 25.

2. If problem persists, call our Technical Assistance Hotline at

1-800-821-2017



NOTE: The diagnostic codes listed above are the most common. If a diagnostic code not listed above is displayed, contact

Residential Technical Support referencing the number on the front of this manual.

*

There may be an audible alarm associated with this error. To cancel the audible alarm, press any bu on on the UIM.


TROUBLESHOOTING

WARNING! Working near an energized

circuit can result in severe injury or death from electrical shock.

WARNING! When you are fi nished, be

sure all covers are secured to reduce the risk of fi re and electric shock.

Troubleshoo ng & Maintenance:

If you are not qualified or are not comfortable performing any of the troubleshooting, repair or maintenance procedures that follow, Call our Technical

Assistance Hotline at 1-800-821-2017 for further assistance.

No Hot Water

The most likely reasons for an electric water heater to produce NO hot water are:

• No power to the water heater (No lights on the unit are on).

• Locate the electrical junction box on the side of the water heater and remove the cover.

• Identify the two power wires. The power wires are usually black/black or black/red-the green or copper wire is the ground wire.

Figure 28 - Use a non-contact circuit tester to check for electrical power.

• Turn the circuit breaker back on (or install the disconnects) and check the power on both incoming power wires using a non-contact circuit tester.

• Turn the power off and replace the cover on the electrical junction box.

• Unit in Vacation Mode.

• ECO tripped.

• Hot water usage pattern exceeds the capability of the water heater in current mode.

• Non-functioning upper temperature sensor.

• Faulty thermostatic mixing valve.

• Leak in plumbing system.

Follow these steps to diagnose and correct common electrical problems:

1

Check the electrical power to the

water heater. No hot water is o en caused by a problem with the homes electrical wiring or circuit breakers. You’ll need a non-contact circuit tester. Follow these guidlines:

• Locate the water heater’s circuit breaker and turn it off (or remove the circuit’s disconnects).

If the water heater is not getting power, contact a qualified person to have your homes wiring or circuit breakers checked.

2

Check the upper hea ng

element. If the water heater is ge ng electrical power, check to see if the upper hea ng element is burned out. If the upper element is burned out, you’ll have no hot water. To check the upper element, you’ll need a mul meter capable of readng resistance.

• Turn the power OFF at the circuit breaker or remove disconnects.

• Remove the upper access panel.

• Move the insulation to the side to access the ECO and heating element.

Check the top two screws of the

3

ECO using a non-contact circuit tester and confi rm that power is off (screw terminals 1 and 3 in photo on next page).

• WIth the electrical power off, remove the two power wires from the upper heating element.

Figure 29 - Use a mul meter to check the resistance of the upper hea ng element.

Check the resistance of the

4 upper hea ng element using a

mul meter. Measure the resistance between the two screw terminals on the upper hea ng element. A good element will have a resistance ranging between 5 and 25 Ohms. If the resistance is:

Outside this range. Replace the element

(see Replacing the Hea ng Element sec-

on on page 27). If the lower element is a concern, repeat the element check procedure for the lower element. The upper and lower elements should have the same resistance range.

Within this range. Rea ach the power wires, making sure the wires are in good condi on and the connec ons are clean and ght. Next check the following: ECO, on next page.


TROUBLESHOOTING

5

Check/Reset Energy Cut Off

ECO Bu on.

• Replace the insulation and the upper access panel.

• Turn the power back on to the water heater.

1 3

Reset Button

FIgure 30 - Energy Cut Off (ECO) bu on

The Energy Cut Off (ECO) shuts off power to the water heater’s elements if the temperature of the water in the tank gets too hot. If the ECO has tripped, you’ll have no hot water. A tripped ECO can usually be reset, but you should have a qualifi ed person inves gate the cause of the overhea ng and repair the problem. Do not turn the power back on un l the cause of the overhea ng has been iden fi ed and repaired.

WARNING! Be sure all covers are

secured to reduce the risk of fi re and electric shock.

Drips from T&P Relief

Valve Discharge Pipe

A small amount of water dripping from the Temperature and Pressure (T&P)

Relief Valve usually means the home’s water pressure is too high or you need a properly sized and pressurized Thermal

Expansion Tank. Refer to Step 1 in the

Installa on sec on of this manual for more informa on. A large amount of hot water coming from the T&P discharge pipe may be due to the tank overheating.

To check the Energy Cut Off (ECO)

• Turn off the power to the water heater.

WARNING! Working near an ener-

gized circuit can result in severe injury or death from electrical shock. Check power wires in the electrical junc on box with a non-contact circuit tester to make sure power is off .

• Press the red ECO reset button (see photo above).

• The ECO was tripped if you hear a click when it is reset. In most cases a tripped ECO indicates that the tank overheated due to a problem with one of the elements. Have a qualified person check the upper and lower elements and replace if necessary.

• The ECO was not tripped if you didn’t hear a click. In that case it should be checked by a qualified person.

WARNING! Do not cap or plug the

T&P relief valve or discharge pipe, and do not operate the water heater without a func oning T&P Relief Valve - this could cause an explosion.

Water pressure too high. High water pressure can cause the T&P Relief Valve to drip. Install a Pressure Reducing Valve

(PRV) on the main cold water supply line. Adjust the PRV to between 50 and

60 psi.

Thermal Expansion Tank. Install a

Thermal Expansion Tank. If a Thermal

Expansion Tank is already installed and the T&P Relief Valve discharge pipe drips, the Thermal Expansion Tank may be pressurized to the wrong pressure or the internal bladder may be defec ve.

Refer to the instruc ons that came with the Thermal Expansion Tank for more informa on.

Debris. In rare cases, debris can s ck inside the T&P Relief Valve preven ng the valve from sea ng fully. In that case, the

T&P Relief Valve discharge pipe will drip.

You may be able to clear debris from the

T&P Relief Valve by manually opera ng the valve, allowing small quan es of water to fl ush out the debris. See the label on the T&P Relief Valve for instruc-

ons.

If the water pressure is between 50 and 60 psi, a Thermal Expansion Tank is installed and properly pressurized, the valve has been cleared of any debris, and it s ll drips, the valve may be broken—have a qualifi ed person replace the T&P relief valve.

Water Odor

Harmless bacteria normally present in tap water can mul ply in water heaters and give off a “ro en egg” smell. A higher tank temperature se ng of 140° kills the bacteria that causes “smelly water” and can reduce the levels of bacteria that cause water-borne disease. A properly adjusted Thermosta c Mixing Valve should be installed at each point of use.

In some cases, the standard anode rod that came with your water heater can be replaced with a special zinc anode rod which may help reduce or eliminate the odor. Contact a qualifi ed person.

NOTE: To protect the tank, an anode rod must be installed in the water heater at all mes or the warranty is void.


TROUBLESHOOTING

WARNING! Because higher temperatures increase the risk of scalding, if you set the UIM se ng higher than 120°F,

Thermosta c Mixing Valves are par cularly important (page 4).

Water Heater Sounds

During the normal operation of the water heater, sounds or noises may be heard. These noises are common and may result from the following:

• Normal expansion and contraction of metal parts during periods of heat-up and cool-down.

• Sediment buildup on or around the elements could create varying amounts of noise and may cause premature tank failure. Drain and flush the tank as directed under the “Draining and Flushing” section.

• The heat pump compressor or fan running.

Temperature Too High

If the water temperature is too hot:

• Adjust the UIM setting on the water heater (see Step 12 in the installation section of this manual).

• Install or adjust a Thermostatic

Mixing Valve (see manufacturer’s instructions)

A nonfunc oning thermostat or a shorted hea ng element can cause extremely hot water. If the Temperature and Pressure Relief Valve (T&P Valve) releases large amounts of very hot water, it is likely due to a shorted hea ng element, or more rarely a nonfunc oning thermostat, or the thermostat does not fi t snuggly against the tank. Very high water temperatures can also cause the Energy

Cut Off (ECO) to trip (see page24). Turn power off un l this problem is fi xed.

Low Water Pressure

Check both the cold and hot water at a sink to determine if the lower pressure is only on the hot water side. If both hot and cold faucets have low pressure, call your local water u lity. If the low pressure is only on the hot water side, the primary causes of this are:

• Melted dip tube. Soldering copper pipes while they are connected to the water heater can melt the inside of the hot and cold water connections or the dip tube (cold water side). A melted dip tube can restrict the flow of hot water. If that’s the case, replace the dip tube.

• Partially closed supply valve. Open the water heater’s supply valve fully.

cient or No Hot

Water or Slow Hot Water Recovery:

WARNING! Because of the increased

risk of scalding, if you set the water heater’s User Interface Module (UIM)

higher than 120°F, Thermosta c Mixing

Valves at each point-of-use are par cularly important (page 4).

If the hot water is simply not warm enough, there are several possible causes:

• Thermostatic mixing valve faulty or set too low.

• Temperature set point too low.

• Hot water usage pattern exceeds the capability of the water heater in current mode (See “Operating Mode

Descriptions”).

• Water connections to unit are reversed (Disconnect and re-install correctly).

• Leak in plumbing system (Check home for any leaks and repair).

• Lower heating element not functioning properly.

• No power to the water heater (No lights on the unit are on and display is blank).

• Unit is in Vacation Mode.

• ECO tripped.

• Non-functioning upper temperature sensor (refer to “Diagnostic Codes” section E60).

• Air filter dirty (See “Air Filter Maintenance” p.33).

• Out of position outlet j-tube (Assure orientation of line on tube is in top position).

• Lower heating element not functioning properly.

Thermosta c Mixing Valves. If the hot water is simply not warm enough, make sure the faucet you are checking doesn’t have a defec ve Thermosta c

Mixing Valve. If these devices fail, they can reduce the amount of hot water the shower or faucet delivers even though there is plenty of hot water in the tank.

Always check the water temperature at several faucets to make sure the problem is not in a faucet or shower control.


TROUBLESHOOTING

User Interface Module (UIM) set too

low. If the water temperature at several faucets is too cool, adjust the UIM according to the instruc ons in Step 12 of the Installa on sec on of this manual.

Lower hea ng element not working.

If the lower hea ng element is not working, you will have some hot water but not as much as before. Because the lower element does most of the work, it usually wears out before the upper element. Replace the lower element if necessary (see page 27).

Undersized water heater. If your water heater runs out of hot water too quickly, it may be too small for your needs. If the water heater is old, consider replacing it with a larger model. If the water heater is in good condi on, you may be able to meet your families hot water needs with the exis ng water heater by installing a

Thermosta c Mixing Valve and then set-

ng the temperature to a higher se ng on the UIM. See “Step 12” on page 16.

You can also reduce your homes hot water needs by washing clothes in cold water, installing fl ow restrictors on shower heads, repairing leaky faucets, and taking other conserva ve steps.

Power Cycling the Unit:

1

Find and turn off the water heater’s circuit breaker or remove disconnects.

2

Find electrical junc on box on side of water heater, remove cover and iden fy the two (2) power wires.

3

Turn circuit breaker back on (or re-install the disconnects) and check for power on both incoming power wires using a voltmeter.

Reversed connec ons or melted J-tube.

Check the hot and cold connec ons and make sure your homes hot water pipe is connected to the hot water outlet on the water heater. Usually reversed connec ons are found soon a er the installa on of a new unit. If copper pipes were soldered while they were a ached to the water heater, the J-tube may have melted. The J-tube is a curved plas c tube inside the tank a ached to the cold water inlet. If the J-tube has melted, it can be replaced by removing the old

J-tube and installing a new one.

Plumbing leak. Even a small leak in the hot water side of the homes plumbing system can make it appear that the water heater is producing li le or no hot water. Locate and repair the leak.

4

Again, turn off water heater’s circuit breaker, or remove disconnect and replace electrical junc on box cover, before performing maintenance work.

NOTE: When powered on the unit will start to run a system diagnostic. This typically takes eight (8) minutes and the UIM will display - -- --- repetitively during this period.

WARNING! Working near an ener-

gized circuit can result in severe injury or death from electrical shock.

WARNING! When you are fi nished,

be sure all covers are secured to reduce the risk of fi re and electric shock.


MAINTENANCE

Rou ne Maintenance

Rou ne maintenance will help your water heater last longer and work better. If you can’t perform these rou ne maintenance tasks yourself, contact a qualifi ed person.

Water Heater Maintenance

A er the fi rst six months, drain and fl ush the water heater and inspect the anode rod. Depending on the hardness of your water, repeat this process at least annually, or more frequently if needed. From me to me you may need to replace a hea ng element or a thermostat. All three maintenance tasks are described below

Draining and Flushing the Water Heater

Tap water contains minerals that can form lime deposits on hea ng elements or sediment in the bo om of the tank. The amount of lime deposits or sediment depends on the hardness of your tap water. The rate at which sediment builds up depends on water quality and hardness in your area, the temperature se ngs, and other variables. We recommend draining and fl ushing the water heater a er the fi rst six months of opera on to determine the amount of sediment build up.

Draining sediment extends the life of the tank, hea ng elements, and drain valves.

• In areas with very hard water, remove and check the heating elements whenever you drain the tank. If you have heavy lime deposits on heating elements, you will need to replace them more often.

• Sediment may form large masses that can prevent the tank from draining.

Have a qualified person use a de-liming agent suitable for potable water to remove the sediment buildup.

• In most cases, it is easier and less expensive to replace lime-encrusted elements than trying to remove heavy lime deposits.

To drain and fl ush the tank:

1

Locate the water heater’s circuit breaker and turn it OFF

(or remove the circuit’s fuses).

Figure 31 - Circuit Breaker

2

Open a hot water faucet and let the hot water run un l it is cool.

5

Open the drain valve on the water heater.

Figure 33 - Drain Valve

6

Open a hot water faucet to help the water in the tank drain faster.

NOTICE! DO NOT turn electrical power back on unless the tank is completely full of water. This is an addi onal precau on to protect the elements against dry fi re. Dry fi re occurs when power is supplied to the electric elements withfi ring the unit will result in immediate failure of the element. While this unit is equipped with dry fi re protec on the recommended prac ce is to ensure the tank is fi lled with water prior to supplying power to the unit.

7

Remove and inspect the anode rod (see Repair Parts

Illustra on on back cover for loca on of the anode rod). Replace the anode rod if it is depleted.

Figure 32 - Water Faucet


3

Connect a garden hose to the drain valve and place the other end of the hose in a drain, outside, or in buckets.

4

Turn the cold water supply valve OFF.

Figure 34 - Anode Rods from new (top) to par ally depleted (middle) to fully depleted stages (bo om)


MAINTENANCE

Anode Rod. The anode rod is a sacrifi cial metal rod that helps reduce corrosion and premature failure (leaks) in the tank. The anode rod is a consumable item. Inspect the anode rod a er the fi rst six months of opera on when you drain and fl ush the tank. Replace the anode rod if it is substan ally worn out or depleted. Therea er, inspect the anode rod annually or more frequently if needed. If you use a water so ener, your anode rod will deplete faster than normal. Inspect the anode rod more frequently, replacing the anode rod as needed. Obtain new anode rods from your local plumbing supplier or have a qualifi ed person replace it. (Anode rods are a consumable item and are not covered under warranty).

8

If the sediment was present when the tank was drained, fl ush the tank by opening the cold water supply valve and le ng the water run un l no more sediment drains from the tank. Close the drain valve when you are done.

NOTICE! Do not turn power back on un l the tank is completely full of water. For complete instruc ons on fi lling the tank, follow Step 10 in the Installa-

on sec on.

9

Refi ll the tank by opening the cold water supply valve. Make sure a hot water faucet is open and the drain valve is closed.

Allow the hot water to run full for at least three minutes to make sure the tank has all the air removed and is completely full of water. Failure to perform this step can cause the upper hea ng element to burn out. Once you are certain the tank is completely full of water, close the hot water faucet.

10

Restore power to the water heater. It may take two hours for the tank to heat up.

Replacing the Hea ng

Element

WARNING! Working on an energized circuit can result in severe injury or death from electrical shock. Turn power off . Check wires with a noncontact circuit tester to make sure power is off . When you are fi nished, be sure all covers are secured to reduce the risk of fi re and electric shock.

If you are not comfortable replacing a hea ng element or thermostat yourself, have this work done by a qualifi ed person. To replace the hea ng element, you’ll need the following tools and supplies: often beveled and may slip. Inexpensive element wrenches are available at your local plumber supplier.

• Garden hose to drain the tank

• Hand dishwashing soap to lubricate the gasket

• A clean cloth to clean the threaded opening

• A flat blade and a Phillips screwdriver

Steps for Replacing the Hea ng

Element:

1

Turn the power OFF at the circuit breaker or remove fuses.

Figure 35 - Non-Contact Circuit Tester

• Always turn power OFF and check the power wires with a non-contact circuit tester before working on the water heater.

Figure 38 - Circuit Breaker

2

Open the electrical junc on box on the side of the water heater. Using a non-contact circuit tester, check the power wires to make certain the power is OFF.

FIgure 36 - Heating Element (with gasket)

• Check your water heater’s data plate for the correct wattage and voltage. Heating elements are available your local plumber supplier.

Figure 37 - Element Wrench

• Some regular sockets (1 1/2 inch) may work, but regular sockets are

Figure 39 - Non-Contact Circuit Tester


MAINTENANCE

3

Open a hot water faucet and let the hot water run un l it is cool.

Figure 40 - Water Faucet


4

Connect a garden hose to the drain valve and place the other end of the hose in a drain or outside (or use buckets). Turn OFF the cold water valve that supplies the water heater. Open the drain valve on the water heater. Opening a hot water faucet will help the tank drain faster.

5

Remove the upper or lower access panel on the water heater, and then fold back the insula on and remove the plas c element/thermostat cover.

7

Remove the bad element using an element wrench.

8

Make sure the new element is the correct replacement by referring to the water heater’s data plate for voltage and wa age informa on.

9

Clean the threads in the tank opening with a rag. Insert the new element equipped with a rubber gasket. NOTE: Use a drop of hand dishwashing liquid to lubricate the gasket to help avoid damaging the gasket as it is being ghtened. Tighten with an element wrench.

NOTICE! Do not turn power back on un l the tank is completely full of water.

For complete instruc ons on fi lling the tank, follow Step 10 in the Installa on sec on.

10

Refi ll the tank by opening the cold water supply valve. Make sure a hot water faucet is open and the drain valve is closed.

Allow the hot water to run full for at least three minutes to make sure the tank has all the air removed and is completely full of water. Failure to perform this step can cause the upper hea ng element to burn out. Once you are certain the tank is completely full of water, close the hot water faucet. the element. Inspect the gasket for damage. If the gasket is damaged, replace the gasket and re-install the element.

12

Once the element is successfully installed and there are no leaks, replace the power wires, thermostat cover, insula on, and access panel. Make sure all wire connec ons are ght. Replace the cover on the electrical junc on box.

13


Replacing the ECO

WARNING! Working on an ener-

gized circuit can result in severe injury or death from electrical shock. Turn power off . Check wires with a noncontact circuit tester to make sure power is off . When you are fi nished, be sure all covers are secured to reduce the risk of fi re and electric shock.

To replace the ECO, you’ll need the following tools and supplies:

• A non-contact circuit tester. Always turn power OFF and check with a non-contact circuit tester before working on the water heater.

Figure 41 - Access Panel

6

With the tank drained and power off , remove the power wires from the element you intend to replace.

Figure 42 - Drain Valve

11

Check the newly installed element for leaks. If a leak is present, ghten the element un l the leak stops. If you cannot stop the leak, drain the tank and remove

Figure 43 - ECO


MAINTENANCE

• A replacement ECO (available by calling the number in the repair parts list located on page 31). A business card to check the gap between the ECO and tank.

• Tape and a permanent marker to mark the wires

• A flat blade and a Phillips screwdriver

Steps for Replacing the

ECO:

1

Turn the power OFF at the circuit breaker or remove fuses.

NOTICE: It is not necessary to drain the tank to replace an ECO.

2

Open the electrical junc on box the side of the water heater.

Using a non-contact circuit tester, check the power wires to make certain the power is OFF.

Power Supply

Connector

1/2” Conduit

Opening

Green Ground

Screw

Green

Ground

Wire

Red Wire

Black Wire

5

6

Mark the wires with tape so you’ll know how to put them back on.

Disconnect the wires from the bad ECO and remove the ECO from the metal moun ng clip.

Install the new ECO in the metal moun ng clip.

7

8

Make sure the new ECO fi ts snuggly against the tank. You should NOT be able to slip a business card between the ECO and the tank. If you can, bend the ECO moun ng clip un l the ECO fi ts ghtly against the tank.

9

A ach the wires following the wiring diagram on the water heater’s label. Make sure all wire connec ons are ght.

10

Replace the plas c element/

ECO cover, insula on, and access panel.

11

12

Replace the cover on the electrical junc on box.


T&P Relief Valve Maintenance

Read and follow the opera ng and annual maintenance instruc ons provided by the manufacturer of the

T&P Relief Valve (yellow label a ached to T&P Relief Valve). Minerals in the water can form deposits that cause the valve to s ck or create blocked passages, making the T&P Relief Valve inopera ve. Follow these guidelines:

• At least annually, operate the T&P

Relief Valve manually to ensure the waterways are clear and the valve mechanism moves freely (below).

Before operating the valve manually, check that it will discharge in a place for secure disposal. If water does not flow freely from the end of the discharge pipe, turn OFF the power to the water heater. Call a qualified person to determine the cause.

WARNING! Hot water will be

released. Before opera ng the T&P

relief valve manually, check that it will discharge in a safe place. If water does not fl ow freely from the end of the discharge pipe, turn the power to the water heater OFF. Call a qualifi ed person to determine the cause.

Figure 44 - Wiring Connec on Box

3

Remove the upper access panel on the water heater and carefully fold back the insula on and plas c element/ECO cover (See fi gure 45 on page 29).

4

Make sure the replacement

ECO matches the original ECO.

Figure 45 - Element Access Panel/ECO

Compartment

Figure 46 - T&P Relief Valve


MAINTENANCE

• At least every five years, have a qualified person inspect the T&P

Relief Valve and discharge pipe.

Damage caused by corrosive water conditions, mineral deposits, or other problems can only be determined when a qualified person removes and inspects the valve and its components.

• Note that a dripping T&P Relief

Valve is usually caused by the home’s water pressure being too high or the lack of a Thermal

Expansion Tank. If your T&P Relief

Valve drips refer to “Drips from T&P

Relief Valve Discharge Pipe” section on page 23.

Air Filter Maintenance

The heater will monitor the heat pump opera on status and indicate whether the fi lter should be cleaned. If the

User Interface Module displays “SF” code, this indicates the fi lter should be cleaned or replaced with the following process (See exploded view of unit on page 31 for air fi lter loca on).

NOTE: Before a emp ng to clean or replace the air fi lter, turn off power to the water heater at the circuit breaker/ fuse box.

1

Take the two tabs on the air fi lter and remove (slide) it from the top cover of the unit.

2

If you are replacing the fi lter, skip to step four. To clean the fi lter, use a vacuum with a hose a achment to remove any dust or debris.

3

4

Place the new or cleaned fi lter into the water heater.

Restore power to the water heater and turn the water heater on.

NOTE: The water heater may conduct a system diagnos c prior to opera on.

Condensate Drain

Maintenance

NOTE: Before a emp ng to clean the condensate drain pan or lines shut off power to the water heater at the circuit breaker/fuse box.

1

Remove the top shroud by loosening the screws securing it to the unit.

2

Check the condensate drain pan and drain lines for any dirt or debris that might interfere with proper drainage. Wipe out any dirt or debris with a damp cloth.

3

Once the condensate drain pan and lines have been inspected/cleaned, secure the shroud back to the top of the water heater.

4

Restore power to the water heater and turn the water heater on.

NOTE: The water heater will conduct a system diagnos c prior to opera on.


REPAIR PARTS ILLUSTRATION

17

15

16

16

21

22

18

14

9

2

1

2

3

8

12

4

REPAIR PARTS

Repair parts may be ordered through your plumber, local distributor, home improvement center, or by calling

1-800-527-1953

. When ordering repair parts always give the following informa on:

1. Model, serial and product number

ANODE LOCATIONS

Back of Unit

36” for 50 and 66 gallon

42” for 80 gallon

Anode

UIM

Anode

14” for 66 and 80 gallon

(50 gallon models have only one anode)

T&P Valve

Front of Unit

6

13

5

7

14

REPAIR PARTS LIST

ITEM

NO.

1

2

3

4

5

5

6

9

10

7

8

11

12

13

14

15

16

17

17

17

17

17

PARTS DESCRIPTION

Personnel Protector

Element (4500 Wa s)

Energy Cut-Off (ECO) Switch

Temperature & Pressure Relief Valve

(T&P)

J-Tube (at hot water outlet) 11.25” for

50 gallon

J-Tube (at hot water outlet) 14.25” for

66 and 80 gallon

Air Filter

Fan Assembly

Drain Valve - Brass - 2 inch

Personnel Protector

Ambient / Coil / Discharge

Temperature Sensor Assembly*

Upper / Lower Tank Temperature

Sensor Assembly*

Electronic Expansion Valve Coil

Condensate Drain Pan

Smart Grid Cover

UIM Front Cover Assembly

(No control board)

Element Access Panel

Anode (36” for 50 and 66 gallon models)*

Anode (14” for 66 and 80 gallon models)*

Anode (42” for 80 gallon models)*

Anode (Universal Link Style)

Magnesium*

Anode (Universal Link Style)

Aluminum*

*Not shown

PART NUMBER

9003900005

9000092015

9008167015

9000728015

9008848005

9009315005

9008850005

9008851005

100262060

319378-000

9008852005

9008853005

9008854005

325892-000

319687-000

100263335

409230-000

9001829005

9001909005

9001829005

9005973005

9005742105

Table 1. 208V/240V

18 Control Board, 208V/240V

19 Run Capacitor*

21 208V Compressor

22 Thermal Overload Kit

*Not shown

100263334

100261846

100261797

100270597


Tefl on® is a registered trademark of Chemours

© 2016 State Industries, Inc. All Rights Reserved.

No results