USB to IDE SATA Standalone Hard Drive Duplicator Dock

UNIDUPDOCK

DE:

Bedienungsanleitung - de.startech.com

FR:

Guide de l'utilisateur - fr.startech.com

ES:

Guía del usuario - es.startech.com

IT:

Guida per l'uso - it.startech.com

NL:

Gebruiksaanwijzing - nl.startech.com

PT:

Guia do usuário - pt.startech.com

For the most up-to-date information, please visit: www.startech.com

Manual Revision: 03/29/2011

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com.

Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Table of Contents

Introduction ........................................................................................................................................................1

Packaging Contents ................................................................................................................................1

System Requirements ............................................................................................................................1

Product View ................................................................................................................................................2

Configuration Buttons ...........................................................................................................................2

Installation............................................................................................................................................................3

Hardware Installation ..............................................................................................................................3

Driver Installation ......................................................................................................................................4

How to Use ..........................................................................................................................................................5

Menu Options .............................................................................................................................................5

Advanced Menu Options .....................................................................................................................7

Duplicator (Copy) Mode .......................................................................................................................8

RAID Mode ....................................................................................................................................................8

Available RAID Modes ............................................................................................................................9

RAID 1 Rebuild ............................................................................................................................................9

Specifications .....................................................................................................................................................10

Technical Support ...........................................................................................................................................11

Warranty Information ....................................................................................................................................11

Instruction Manual i

Introduction

The StarTech.com UNIDUPDOCK functions as both a convenient hard drive copying/imaging solution and an external USB to SATA/IDE HDD docking station for 2.5” (up to 500Gb) or 3.5” hard drives (up to 2 TB).

Packaging Contents

• 1 x UNIDUPDOCK duplicator dock

• 1 x USB cable

• 2 x 40-pin IDE ribbon cable (female/female)

• 2 x LP4 molex adapter cable

• 2 x 40 to 44-pin IDE adapter

• 1 x Universal Power Adapter

• 3 x Power Cords (NA/UK/EU)

• 1 x Instruction Manual

System Requirements

2.5” and/or 3.5” SATA and/or IDE hard drive(s)

USB operation:

Microsoft

®

Windows

®

2000/XP/Vista/7 (32/64-bit), or Apple ® Mac OS ® X, or Linux ®

Instruction Manual 1

Product View

Built-in LCD screen

Configuration buttons

LP4 molex connector

USB connector

40-pin IDE connector

ON/OFF switch

Power connector

7+15 SATA connector

Configuration Buttons

Button

ENT

ESC

RESET

MUTE

Function

Navigate Up

Navigate Down

Enter

Cancel

Reset duplicator dock (soft)

Mute buzzer sounds

Instruction Manual 2

Installation

WARNING:

Hard drives require careful handling, especially when being transported. If you are not careful with your hard disk, lost data may result. Always handle your hard drive and storage device with caution.

Hardware Installation

1. Plug the universal power adapter into a wall power outlet and into the DC In connector on the duplicator dock.

2. If using a SATA hard drive as the source disk, gently slide the hard drive into the 7+15 SATA connector labeled Source-1 on the duplicator dock. Skip to step 6.

3. If using an

IDE hard drive as the source disk, connect the IDE ribbon cable (included) to the 40-pin connector labeled Source-2. The connector is keyed to fit only one way.

4. Connect the LP4 molex cable (included) into the 4-pin connector next to the 40-pin IDE connector. The connector is keyed to fit only one way.

5. The jumper settings on IDE hard drives must be set to either ‘master’ or ‘cable select’. Refer to hard drive manufacture if unsure how to set.

6. Connect the IDE hard drive to the ribbon cable and LP4 molex connector. If connecting a

2.5” IDE hard drive, attach the 40 to 44-pin adapter to the end of the ribbon cable and LP4 cable, then connect the hard drive to the adapter.

NOTE:

Only one Source disk and one Destination disk can be installed at a time. Only connect a SATA or an IDE hard drive, not both.

Instruction Manual 3

7. Follow the same procedure for either a SATA or IDE hard drive for the Destination side of the duplicator dock.

NOTE:

SATA and IDE hard drives can be mixed, so one side can be SATA while the other is IDE.

8. Slide the power ON/OFF switch on the side of the unit to the ON position, to power up the unit.

9. Once the unit has booted up, use the configuration buttons and built-in LCD display to configure and operate the duplicator dock.

10. If using as an external hard drive dock, connect the USB cable from the duplicator dock to the computer’s USB port.

Instruction Manual 4

Driver Installation

No driver installation is required for any supported operating system, as this hard drive dock is natively supported, so the drivers are already installed.

How to Use

Menu Options

Copy HDD

• Perform a 1:1 sector clone from the Source disk to the Destination disk. Each disk sector on the Source disk will be copied, regardless if it contains data or not. If using a Destination disk larger than the Source, any extra space will be untouched and left unallocated.

Instruction Manual 5

Compare HDD

• Compares the sectors on the Source disk to the Destination disk. Used to ensure that the

Copy operation was successful.

Pre-scan

• Scans the Source disk for bad sectors/blocks and reports the errors.

Rescan Bus

• Rescans the hard drive connectors on the duplicator dock to detect new/swapped drives.

Source Size

• Displays the total storage capacity of the Source disk.

Setup

System information and settings

• DMA Mode

• Switch between different DMA modes, for better compatibility across different drives. Will affect maximum data transfer rates.

Copy Size

• Specify the percentage of the source drive that should be copied.

Startup Menu

• Sets the first item that should be selected from the main menu on startup.

Auto Compare

• Automatically runs the Compare HDD function after copying. OFF by default.

Copy with Detect

• Automatically rescans the bus before beginning Copy operation. OFF by default.

Button Sound

• Turn audio feedback (beeping) ON/OFF.

Device Info

• Lists disk information about the Source/Destination disks.

System Info

• Lists information about the duplicator, such as firmware version.

USB RAID Mode

• Set the RAID mode for the attached drives when connected to a computer via USB.

Switch between USB and Duplicator modes.

Instruction Manual 6

Advanced Menu Options

The Advanced Menu can be access from the main menu by pressing and holding the <ESC> button for several seconds.

Rescan Bus Delay

• Sets the time interval delay before starting “Rescan Bus” from the main menu.

Read Error Skip

• Ignore any read errors (sector or block) detected during the copying process. Normally, read errors result in cancellation of the copying process. OFF by default.

Quick Erase HDD

• Quickly erase all the data on the Source hard drive.

H/W Diagnostic

• Runs though a suite of self diagnostic tests and displays the results.

Load Default

• Resets all settings to factory defaults.

Link Option

• Enable/disable the “USB RAID Mode” option from appearing in the Main Menu.

USB Auto-Link

• Automatically enter USB mode on startup. OFF by default.

Copy HPA

• Copy the Source drive’s Host Protected Area during duplication. OFF by default.

Instruction Manual 7

Duplicator (Copy) Mode

Use the <UP> and <DOWN> arrows on the duplicator dock to select the Copy HDD mode and press the ENT button to activate. The LCD screen will display transfer rates, progress percentage, amount of data copied and a countdown timer.

NOTE:

As the duplicator dock creates a 1:1 copy, the Destination disk must be of equal or greater capacity than the Source disk.

RAID Mode

Use the <UP> and <DOWN> arrows to navigate to the Setup Mode and press the ENT button.

Navigate to the “Change RAID Mode” option and press ENT.

NOTE:

Changing the RAID mode may result in data loss, so make sure all important data is backed up, before attempting to change the RAID mode.

Instruction Manual 8

Available RAID Modes

Mode

Normal

RAID0

Function

Two independent disks

Striped drives for maximum data transfer rates. Combined capacity will be double the smallest drive. No redundancy/backup.

Mirroring a single drive to create two exact copies.

RAID1

JBOD Concatenate two drives to create a single large disk.

RAID 1 Rebuild

When operating in RAID1 mode, if one of the hard drives fails or is removed, the duplicator dock will enter a failed state and a buzzer will sound once per second.

Use the <UP> and <DOWN> arrows to display information on either Drive1 (Source) or Drive2

(Destination).

Reconnect a hard drive to the appropriate Source of Destination side and the duplicator dock will automatically prompt for a rebuild.

The progress of the rebuild will be displayed, including the transfer speed, percentage complete and a countdown timer to completion.

Instruction Manual 9

Specifications

Bus Interface

Chipset ID

Connectors

LEDs

RAID Modes

Maximum Data Transfer Rate

Hard Drive Compatibility

Dimensions

Weight

Compatible Operating Systems

USB 2.0

ACARD ARC286

2 x 7+15 SATA connector

2 x 40-pin IDE male

2 x LP4 molex male

1 x USB type B

1 x DIN power connector

4 x Disk Power/Activity

0, 1, JBOD (concatenation), single disks

USB: 480Mb/s

2.5” SATA 1.5/3.0Gb/s and

ATA/33/66/100/133 drives up to

500GB in capacity

3.5” SATA 1.5/3.0Gb/s and

ATA/33/66/100/133 drives up to 2TB in capacity

151.0mm x 110.0mm x 27.0mm

235g

Windows 2000/XP/Vista/7,

Mac OS X, Linux

Instruction Manual 10

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commit-ment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.

com/support and access our comprehensive selection of online tools, documentation, and downloads.

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Instruction Manual 11

Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.

StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions.

We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.

Visit

www.startech.com

for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.

StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States,

Canada, the United Kingdom and Taiwan servicing a worldwide market.