Hochiki FireNET 4127 Installation and Operation Manual

Hochiki FireNET 4127 is an analog addressable fire alarm system designed to provide early warning of fire and other emergencies. It is a versatile system that can be used in a variety of applications, from small businesses to large industrial facilities. The FireNET 4127 offers a wide range of features, including:

Analog addressable technology for fast and accurate detection of fire and other emergencies
A variety of input and output devices to meet the needs of any application
A user-friendly interface that makes it easy to program and operate the system
Remote monitoring and control capabilities for added convenience and peace of mind

PDF

Document

FireNET 4127

Analog Addressable Fire Alarm System

Installation and Operation Manual

Hochiki America Corporation

7051 Village Drive, Suite 100

Buena Park, CA 90621-2268

714.522.2246 Corporate Headquarters

800.845.6692 Technical Support http://www.hochiki.com

Version 1.90 - UL

Created: 08/15/05

Updated: 08/24/2010

PN# 1700-09948

v1.90 UL FireNET 4127 I & O Manual 1

Table of Contents ........................................................................................................................... 2

Prefix – Programming Compliance with UL864 9 th

Edition ........................................................ 7

Section 1 – Introduction

......................................................................................................................................................... 8

1.1 Basic Features .................................................................................................... 8

1.2 System Devices and Equipment ......................................................................... 9

1.2A System Devices BOSCH ................................................................................ 11

1.2B System Devices Silent Knight ........................................................................ 12

1.2.1 System Replacement Parts ......................................................................... 13

1.3 Limitations of Fire Alarm Systems .................................................................... 14

1.4 Agency Listings, Approvals, Requirements ...................................................... 17

1.4.1 Federal Communications Commission (FCC) .............................................. 17

1.4.2 Underwriters Laboratories (UL) .................................................................... 17

1.4.3 National Fire Protection Association (NFPA) ............................................... 17

Section 2 – Control Panel Installation

....................................................................................................................................................... 18

2.1 What’s in the Box? ............................................................................................ 18

2.2 Environmental Specifications ............................................................................ 18

2.3 Control Panel Layout ........................................................................................ 19

2.3.1 Front Panel Layout, Standard Build ............................................................. 19

2.3.2 Front Panel Layout, Denver Door Build ....................................................... 20

2.3.3 Control Panel Annunciator, Control Unit and Power Supply Layout ............ 21

2.4 Mounting the Control Panel .............................................................................. 22

2.5 Wiring Specifications ........................................................................................ 22

2.5.1 Suggested Routing of AC Power ................................................................. 23

2.6 Battery Calculations .......................................................................................... 24

2.7 Electrical Ratings .............................................................................................. 27

2.8 Specifications ................................................................................................... 30

Section 3 - Power Supply and Main Control Unit Connections

....................................................................................................................................................... 31

3.1 AC Power Connection ...................................................................................... 31

3.2 Battery Connection ........................................................................................... 31

3.3 Auxiliary Power Connection .............................................................................. 32

3.4 Notification Appliance Circuit Connection ......................................................... 34

3.5 Voltage Routing and Relay Output Connection ................................................ 35

3.5.1 Voltage Routing Outputs .............................................................................. 35

3.5.2 Relay Outputs .............................................................................................. 36

3.6 Digital Input Connection .................................................................................... 37

3.7 Using a Printer .................................................................................................. 38

Section 4 – Expander Board Installation

....................................................................................................................................................... 39

FireNET 4127 I & O Manual v1.90 UL

4.1 Compatible Expander Boards ........................................................................... 39

4.2 General Installation of RS-485 Bus Devices ..................................................... 40

4.2.1 Wiring Distance and Mounting Locations ..................................................... 40

4.2.2 Addressing ................................................................................................... 41

4.2.3 Terminating .................................................................................................. 41

4.2.4 Power Connections ...................................................................................... 42

4.2.5 COMMS Connection .................................................................................... 42

4.3 FN-4127-IO - Input / Output Board ................................................................... 43

4.3.1 Configuring Inputs ........................................................................................ 43

4.3.2 Configuring Outputs ..................................................................................... 44

4.3.3 LED Indicators ............................................................................................. 45

4.4 Reserved for Future Use .................................................................................. 45

4.5 Reserved for Future Use .................................................................................. 45

4.6 FN-4127-SLC – Dual SLC Loop Expander ....................................................... 46

4.6.1 Installation of the FN-4127-SLC ................................................................... 46

4.7 FN-LCD-S Serial Liquid Crystal Display Annunciator ...................................... 47

4.7.1 Installation of the FN-LCD-S ........................................................................ 47

Section 5 – SLC Device Installation

....................................................................................................................................................... 50

5.1 Compatible SLC Devices .................................................................................. 50

5.2 Number of Devices ........................................................................................... 52

5.3 SLC Loop Wiring .............................................................................................. 52

5.3.1 Class B SLC Loop Wiring Distance ............................................................. 53

5.3.2 Class A SLC Loop Wiring Distance ............................................................. 54

5.4 Addressing Devices .......................................................................................... 55

5.4.1 Detector Addressing .................................................................................... 57

5.4.2 4-S Module and AMS Addressing ............................................................... 57

5.4.3 Mini Module Addressing .............................................................................. 58

5.5 Smoke and Heat Detector Wiring ..................................................................... 59

5.6 Analog Duct Detector Wiring ............................................................................ 60

5.6.1 DH98-A Analog Duct Detector ..................................................................... 61

5.6.2 DH98-AR Analog Duct Detector with Relay ................................................. 62

5.7 FRCME-4 Input Module Wiring ......................................................................... 63

5.8 FRCME-S Mini Input Module (w/ Terminal Blocks) ........................................... 64

5.9 FRCME-P Mini Input Module (w/ Pigtails) ......................................................... 65

5.10 FRCME-M Mini Input Module (w/ Terminal Blocks) ........................................ 66

5.11 FRCMA / FRCMA-I Input Module ................................................................... 67

5.12 R2M Dual Relay Module Wiring ...................................................................... 69

5.13 SOM Supervised Output Module .................................................................... 70

5.14 SOM-A / SOM-AI Supervised Class A Output Module .................................... 71

5.15 SOM-R Supervised Output Module (Preaction Sprinkler Systems) ................ 72

5.15 CZM Conventional Zone Module .................................................................... 76

5.16 DIMM Dual Input Monitor Module ................................................................... 77

5.17 SCI Short Circuit Isolator Module .................................................................... 78

5.17.1 Class A Operation ...................................................................................... 79

5.17.2 Class B Operation ...................................................................................... 80

5.18 ASB Analog Sounder Base ............................................................................. 81

5.19 AMS Addressable Manual Pull-Station ........................................................... 82

FireNET 4127 I & O Manual v1.90 UL

Section 6 - Network Connections

....................................................................................................................................................... 83

6.1 Compatible Network Devices ............................................................................ 83

6.1.1 FN-4127-NIC Network Interface Card .......................................................... 84

6.1.2 FN-LCD-N Network Liquid Crystal Display Annunciator .............................. 89

Section 7 - Basic Front Panel Operations and Programming .................................................. 91

(Access Level 1, 2, and Real-Time Operation)

....................................................................................................................................................... 91

7.1 Operating Modes .............................................................................................. 92

7.1.1 Access Level 1 ............................................................................................. 92

7.1.2 Access Level 2 ............................................................................................. 92

7.1.3 Access Level 3 ............................................................................................. 92

7.2 Access Level 1 Operations ............................................................................... 92

7.2.1 Performing a Lamp Test .............................................................................. 92

7.2.2 More Fire Events ......................................................................................... 93

7.2.3 More Events ................................................................................................. 93

7.2.4 Menu Navigation (Up, Down, Left, Right Arrows, Enter / Exit Buttons) ........ 93

7.2.5 Help (?) ........................................................................................................ 93

7.3 Access Level 2 Operations ............................................................................... 94

7.3.1 Entering Access Level 2 .............................................................................. 94

7.3.2 Silencing an Alarm ....................................................................................... 94

7.3.3 Resounding an Alarm .................................................................................. 94

7.3.4 Resetting an Alarm ...................................................................................... 95

7.3.5 Initiating a Fire Drill ...................................................................................... 95

7.3.6 Silence the Panel Sounder .......................................................................... 95

7.4 Advanced Access Level 2 Operations .............................................................. 96

7.4.1 Access Level 2 Main Menu .......................................................................... 96

7.4.2 Disablements ............................................................................................... 96

7.4.3 View Devices ............................................................................................... 98

7.4.4 Test Zones ................................................................................................... 98

7.4.5 Set System Time ......................................................................................... 99

7.5 Panel Operation ................................................................................................ 99

7.5.1 Fire Condition .............................................................................................. 99

7.5.2 Trouble Condition ...................................................................................... 100

7.5.3 Supervisory Condition ................................................................................ 101

7.5.4 Pre-Alarm Condition .................................................................................. 102

Section 8 - Advanced Front Panel Operations and Programming (Access Level 3)

..................................................................................................................................................... 103

8.1 Access Level Overview ................................................................................... 103

8.1.1 Entering Access Level 3 ............................................................................ 103

8.2 Access Level 3 Menu ...................................................................................... 104

8.2.1 Edit Configuration ...................................................................................... 104

8.2.2 Set Times................................................................................................... 112

8.2.3 View Print Event Log ................................................................................. 113

8.2.4 Print Configuration ..................................................................................... 114

8.2.5 System Disablements ................................................................................ 114

8.2.6 Loop Data Test .......................................................................................... 115

FireNET 4127 I & O Manual v1.90 UL

Section 9 - Loop Explorer Software Programming

..................................................................................................................................................... 116

9.1 PC Requirements ........................................................................................... 116

9.2 Installing Loop Explorer .................................................................................. 116

9.3 Launching Loop Explorer ................................................................................ 117

9.4 Connecting Your PC to the FireNET 4127 ...................................................... 117

9.4.1 Using PC Connect ..................................................................................... 117

9.4.2 Setting a COM Port .................................................................................... 122

9.5 Getting Familiar with Loop Explorer ................................................................ 122

9.5.1 User Interface ............................................................................................ 123

9.5.2 Menu and Toolbar Overview ...................................................................... 125

9.5.3 Main Tool Bar Icons ................................................................................... 132

9.5.4 Items Pane Icons ....................................................................................... 134

9.6 Developing a Site............................................................................................ 138

9.6.1 Creating a New Site ................................................................................... 138

9.6.2 Editing an Existing Site .............................................................................. 139

9.6.3 Saving a Site .............................................................................................. 140

9.7 Configuring Panels to a Network .................................................................... 141

9.7.1 Adding a Panel .......................................................................................... 141

9.7.2 Configuring and Editing a Panel ................................................................ 142

9.7.3 Editing a FN-LCD-N Network LCD Annunciator ......................................... 147

9.7.4 Reserved for Future Use ........................................................................... 147

9.7.5 Editing a Local Panel I/O ........................................................................... 148

9.7.6 Removing a Panel ..................................................................................... 148

9.8 Configuring Option Boards/Serial LCD Annunciators on a Panel ................... 149

9.8.1 Adding an Option Board/Serial LCD Annunciator ...................................... 149

9.8.2 Editing an Option Board/Serial LCD Annunciator ...................................... 149

9.8.3 Removing an Option Board/Serial LCD Annunciator ................................. 150

9.9 Configuring Panel I/O and Devices on a Loop ................................................ 151

9.9.1 Adding a Device on a Loop ........................................................................ 151

9.9.2 Editing Panel I/O and Devices on a Loop .................................................. 151

9.9.3 Changing a Device on a Loop .................................................................... 157

9.9.4 Deleting a Device on a Loop ...................................................................... 157

9.10 Loop Explorer Abilities .................................................................................. 158

9.10.1 Reserved for Future Use.......................................................................... 158

9.10.2 Cause & Effect Summary......................................................................... 158

9.10.3 Reserved for Future Use.......................................................................... 158

9.10.4 Zone Manager ......................................................................................... 158

9.10.5 Reserved for Future Use.......................................................................... 158

9.11 Loop Explorer Networking ............................................................................ 159

9.11.1 Getting it working ..................................................................................... 159

9.11.2 Using the Loop Explorer PC configuration ............................................... 159

9.11.3 Fire action ................................................................................................ 160

9.11.4 Auxiliary action ......................................................................................... 160

9.11.5 Pre-alarm action ...................................................................................... 160

9.11.6 Trouble action .......................................................................................... 160

9.11.7 Disablement action .................................................................................. 161

9.11.8 Supervisory Alarm action ......................................................................... 161

9.11.9 Test action ............................................................................................... 161

9.11.10 Status .................................................................................................... 161

FireNET 4127 I & O Manual v1.90 UL

9.12 Loop Explorer Networking - Keeping a record .............................................. 164

9.13 Loop Explorer Networking - Using zones ...................................................... 171

9.14 Loop Explorer Options .................................................................................. 172

9.14.1 COM Port ................................................................................................. 172

9.14.2 Default Project Folder/ Memory Management ......................................... 172

9.14.3 Splash Screen ......................................................................................... 172

9.14.4 Other ........................................................................................................ 173

9.15 Cause and Effect Programming .................................................................... 174

9.15.1 Cause & Effect Types .............................................................................. 174

9.15.2 Cause & Effect Examples ........................................................................ 176

Section 10 - Testing and Troubleshooting

..................................................................................................................................................... 178

10.1 One Man Walk Test - TEST ZONES ............................................................ 178

10.2 View / Print Event Log .................................................................................. 179

10.2.1 View Event Log ........................................................................................ 179

10.2.2 Print Event Log ........................................................................................ 180

10.2.3 Clear Event Log ....................................................................................... 181

10.3 Loop Data Test ............................................................................................. 182

10.4 Troubleshooting ............................................................................................ 184

Section 11 - Installation Records

..................................................................................................................................................... 186

11.1 SLC Loop Point Record ................................................................................ 186

11.2 RS485 Bus Device Record ........................................................................... 186

11.3 Network Node Device Record ...................................................................... 186

Appendix A - Compatible Devices

..................................................................................................................................................... 199

A.1 Two-Wire Smoke Detectors ........................................................................... 199

A.1.1 Two-Wire Smoke Detectors BOSCH ........................................................... 200

A.2 Reserved for Future Use ................................................................................ 200

A.3 Compatible Notification Appliances ................................................................ 201

A.4 Compatible 24VDC Devices ........................................................................... 206

A.4.1 Compatible 24VDC Devices BOSCH .......................................................... 207

A.5 Using the Bosch D9068 Dialer with FireNET .................................................. 208

A.5.1 Using the Bosch D9068 Contact Dialer with FireNET (Diagram) ............... 208

A.5.2 Programming FireNET for use with the Bosch D9068 Dialer..................... 209

A.5.3 Installation notes when using the Bosch D9068 Dialer with FireNET ........ 212

A.6 Using the FN-CTM City Tie module with FireNET .......................................... 213

A.7 Using the FNV-MP with FireNET .................................................................... 214

A.8 Changing the FN-PS402 Power Supply to 240VAC operation ....................... 215

Appendix B – Panel Door Label Drawing ................................................................................. 216

Appendix C - WARRANTY ......................................................................................................... 217

FireNET 4127 I & O Manual v1.90 UL

Prefix – Programming Compliance with UL864 9 th

Edition

Notice to Users, Installers, Authorities Having Jurisdiction, and other involved parties

This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864 9 th

Edition, certain programming features or options must be limited to specific values or not used at all as indicated below.

Program Feature or

Option

Permitted in UL 864?

(Y/N)

Possible settings

Settings permitted in

UL864

AC Fail Delay Yes 0 – 24 hours 1 – 3 hours

Alarm Verification Yes 5 – 60 seconds 60 second setting

Disable Buzzer Yes Enable/Disable Enable

Disable Ground Trouble

Set Buzzer Silence

Access Level

Yes

Enable/Disable

1 or 2

Enable

“Waterflow Alarm” and

“General Purpose” Device

Type

No 0 – 120 seconds 0 seconds

Disable SOM-R No Enable/Disable None

FireNET 4127 I & O Manual v1.90 UL

Section 1 – Introduction

The FireNET 4127 is an analog addressable fire alarm system that meets the requirements of UL 864 9 th

Edition.

1.1 Basic Features

The basic FireNET 4127 control panel includes two SLC (Signaling Line Circuit) loops. Each loop is capable of supporting 127 analog addressable points (can be any combination of sensors and modules) for a total of 254 analog addressable points on the basic panel. Two additional SLC loops can be added to the panel increasing the analog addressable point capacity to 508. When analog sounder bases are used, the upper addresses 128 – 254 are allocated to increase loop capacity to 254 analog addressable points. This doubles the analog addressable point capacity of the panel. The combination of analog addressable points derived from sensors, modules, and sounder bases cannot exceed 800 addresses and sub-addresses maximum.

Up to 4.0 amps of power is available to drive the system, SLC loops, notification appliances, and auxiliary equipment.

Four Class B notification appliance circuits rated at 2.5 amps each (see Section

2.7 and 2.8 for additional details regarding NAC circuit ratings).

Five programmable Form C relays are built-in to the control panel.

500 network-wide zones for device and circuit grouping.

Analog Smoke Detector Features:

Automatic Drift Compensation

Day/Night

Calibration checking meets sensitivity test requirements of NFPA 72.

Auto-Learn utility identifies system devices, which makes initial system start-up easier.

8 line by 40 character graphic display provides the most intuitive operator interface in the industry (320 characters total).

Help screens are available from the front panel and annunciator user interface to assist in programming and operation.

512 additional points can be added to the system using the FN4127-IO 16 channel input/output boards. Each of these points can be programmed individually to be an input or low current output. These points are for secondary use only.

FireNET 4127 I & O Manual v1.90 UL

1.2 System Devices and Equipment

The following boards, expanders and devices are available from Hochiki America

Corp. to be used with the FireNET 4127 analog addressable fire alarm system. For a complete description and installation instructions of each product, please see the appropriate section of this manual and the literature supplied with the device itself.

Model

Control Panels

Description

FN-4127

Analog/Addressable Fire Alarm Control Panel

(2 SLC Loop, expandable to 4 SLC Loop)

NOTE: There are several ordering models (i.e. 2 loop, 4 loop, network options,

120/240VAC, colors, etc.). Hochiki America’s order entry department will establish exact model and configuration at time of order. Different ordering models are also reflected on the FireNET product datasheets.

Control Panel Expanders

FN-4127-NIC

FN-4127-SLC

FN-4127-IO

Network Interface Card

Dual SLC Loop Expander Card

16 Channel Input Output Board

FN-LCD-N

FN-LCD-S

ALK-V

ALK-V2

ALG-V

AIE-EA

ATG-EA

YBN-NSA-4

HSB-NSA-6

DH98-A

DH98-AR

MS-RA, MS-RA/R, MS-

KA/R

FRCME-4

FRCME-S

FRCME-P

FRCME-M

FRCMA, FRCMA-I

SOM, SOM-A, SOM-AI

SOM-R

Annunciators

Network LCD Annunciator

Serial LCD Annunciator

SLC Loop Devices

Analog Photoelectric Smoke Sensor

Analog Ionization Smoke Sensor

Analog Heat Sensor

4” Base for Analog Sensors

6” Base for Analog Sensors

Analog Duct Smoke Detector

Analog Duct Smoke Detector w/Relay

Remote Test Station for DH98A & DH98AR

Input Module 4” Box Mount

Mini Input Module w/ Terminal Block

Mini Input Module w/Pigtail Leads

Mini Input Module w/ Terminal Block

Class A Input Module 4” Box Mount (FRCMA-I has built-in SCI)

Supervised Output Module

Supervised Output Module (Preaction Sprinkler Systems)

R2ML, R2ML-I Dual Relay Module, 2 amp @ 30VDC (R2ML-I has built-in SCI)

FireNET 4127 I & O Manual v1.90 UL

R2MH, R2MH-I

SCI

DIMM

ASB

AMS/KL/LP

Dual Relay Module, 8 amp @ 30VDC (R2MH-I has built-in SCI)

Short Circuit Isolator Module

Dual Input Monitor Module

Analog Sounder Base

Addressable Manual Pull-Station

Accessories

FN-ACC

FN-ETR

Battery/Accessory Enclosure (houses up to 33AH size batteries)

Enclosure Trim Ring for Panel Flush Mount

FireNET 4127 I & O Manual v1.90 UL

1.2A System Devices BOSCH

The following boards, expanders and devices are available from BOSCH to be used with the FireNET 4127 analog addressable fire alarm system. For a complete description and installation instructions of each product, please see the appropriate section of this manual and the literature supplied with the device itself.

Model Description

Control Panels

FN-4127

D5070

NOTE: There are several ordering models (i.e. 2 loop, 4 loop, network options, 120/240VAC, colors, etc.). Bosch’s order entry department will establish exact model and configuration at time of order. Different ordering models are also reflected on the FireNET product datasheets.

D323A

D324A

D322A

D336A

D321A

D331A

D332A

D326A

D339A

D327A

D335A

Analog/Addressable Fire Alarm Control Panel

(2 SLC Loop, expandable to 4 SLC Loop)

SLC Loop Devices

Analog Photoelectric Smoke Sensor

Analog Ionization Smoke Sensor

Analog Heat Sensor

4” Base for Analog Sensors

6” Base for Analog Sensors

Analog Duct Smoke Detector

Analog Duct Smoke Detector w/Relay

Input Module 4” Box Mount

Mini Input Module w/ Terminal Block

Supervised Output Module

Dual Relay Module

Accessories

Hand-held Programmer

FireNET 4127 I & O Manual v1.90 UL

1.2B System Devices Silent Knight

The following boards, expanders and devices are available from Silent Knight to be used with the FireNET 4127 analog addressable fire alarm system. For a complete description and installation instructions of each product, please see the appropriate section of this manual and the literature supplied with the device itself.

Model Description

SD505-APS

SLC Loop Devices

Analog Photoelectric Smoke Sensor

SD505-AIS Analog Ionization Smoke Sensor

SD505-AHS Analog Heat Sensor

SD505-4AB 4” Base for Analog Sensors

SD505-6AB 6” Base for Analog Sensors

SD505-DUCT Analog Duct Smoke Detector

Accessories

SD505-DTS-K Remote Test Switch

FireNET 4127 I & O Manual v1.90 UL

FN-4127-BO

FN-4127-CPA-BO

FN-PS4

FN-PS402*

FN-ENC

FN-ENC-DO

FN-ENC-BC

FN-PMP

FN-PBS

FN-PGB

FN-EOL

FN-STO

FN-PRC

FN-FUS

FN-FUS-BATT

FN-BLJ

FN-MAN

FN-PDL

FN-LSW

FN-X187

FN-S187

FN-SKDK

FN-SKCK

FN-ECK

FN-BLE

FN-LCD-N-ETR

FN-LCD-N-BB

1.2.1 System Replacement Parts

Control Panel Repair / Replacement Parts

FireNET 4127 Control Unit Board Only (K6002)

FireNET 4127 Panel Annunciator Board Only (K6001)

FireNET 4 Amp Power Supply (UL864 8 th

Edition Compliant)

FireNET 4 Amp Power Supply (UL864 9 th

Edition Compliant)

FireNET Enclosure Complete

FireNET Enclosure Door Only

FireNET Enclosure Back-Can Only

FireNET Panel Mounting Plate

FireNET Panel Bonding Strap

FireNET Panel Grounding Block

FireNET Panel EOLR (package)

FireNET Panel Standoffs (for panel covers)

FireNET Panel Ribbon Cables (package)

FireNET Main AC Input Fuse

FireNET Battery Input Fuse

FireNET Battery Leads & Jumper

FireNET Installation Manual

FireNET Panel Door Label

Loop Explorer Software CD

Programming Cable (Standard)

Programming Cable (Jacketed)

Spare Keys for Door Keyswitch

Spare Keys for Controls Keyswitch

Enable Controls Keyswitch

Battery Leads for Accessory Enclosure (extended length 3.28ft)

Enclosure Trim Ring for Network Annunciator Flush Mount

Network Annunciator Back-box

FN-LCD-S-BO

FN-LCD-S-BB

FN-EBS

FN-ENC-DD

FN-CB-DD

Serial Annunciator Control Unit Board Only (K6017)

Serial Annunciator Back-box

Expansion Boards Standoffs (SLC board & I/O board stacking)

Denver Door Enclosure Front Door, including clear window

Denver Door Circuit Board Mounting Plate

FN-KEY-DD

CAT-30 Enclosure Key and Lock for FireNET and FireNET

Denver Door version

Access Level 2 Switch for Denver Door Build FN-S-DD

*NOTE: 240VAC option available

FireNET 4127 I & O Manual v1.90 UL

1.3 Limitations of Fire Alarm Systems

Follow Recommended Installation Guidelines: To achieve early fire detection, fire detection sensors should be installed in all rooms and areas of a house, apartment, or building in accordance with the recommendations of the National Fire Protection

Association Standard 72 (NFPA 72), manufacturer’s recommendations, state and local codes, and the recommendations contained in Guide for the Proper Use of

System Smoke Detectors, which is made available at no charge to all installing dealers. Generally, the standards and recommendations include the following (but installers should refer to the specific guidelines above before installing): room.

• Hallways: More than one smoke detector should be installed in a hallway if it is more than 30 feet long.

• At least Two Smoke Detectors: There should never be less then two smoke detectors per apartment or residence.

• Smoke Detectors in Alarm, Electrical, or Phone Locations: Smoke detectors should be located in any room where an alarm control is located or an alarm control connects to an electrical source or phone line. If detectors are not so located, a fire within the room could prevent the alarm control from reporting a fire.

Systems: All fire alarm systems require notification devices, including sirens, bells, horns, and/or strobes. In residential applications, each automatic alarm initiating device when activated should cause the operation of alarm notification device that should be clearly audible in all bedrooms over ambient or background noise levels (at least 15dB above noise) with all intervening doors closed.

• Alarm in Every Bedroom and Level of Residence: A smoke detector with an integral sounder (smoke alarm) should be located in every bedroom and an additional notification device should be located on each level of a residence.

• Maintenance: A maintenance agreement should be arranged through the local manufacturer’s representative and maintenance should be performed annually by authorized personnel only. To keep a fire alarm system in excellent working order, ongoing maintenance is required per the manufacturer’s recommendations and UL and NFPA standards. At a minimum the requirements of Chapter 7 of NFPA 72 (1999) shall be followed.

Weekly: The alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The most common cause of an alarm system not functioning when a fire occurs is inadequate maintenance.

Alarms Cannot Guarantee Warning or Protection: Fire alarm system cannot guarantee warning or protection against fire in every potential situation. A study by the Federal Emergency Management Agency (an agency of the United States government) indicated that smoke detectors may not go off or give early warning in as many as 35% of all fires.

FireNET 4127 I & O Manual v1.90 UL

Limitation on Fire Alarm Effectiveness: A fire alarm system may not provide timely or adequate warning, or simply may not function, for a variety of reasons. For example: not reach the sensing chambers of smoke detectors because:

1. Barriers (such as closed or partially closed doors, walls, or chimneys) may inhibit particle or smoke flow.

2. Smoke particles may become cold, stratify, or not reach the ceiling or upper walls where detectors are located.

3. Smoke particles may be blown away from detectors by air outlets.

4. Smoke particles may be drawn into air returns before reaching the detector.

• No Multi-Floor Detection: In general, smoke detectors on one level of a structure cannot be expected to sense fires developing on another level.

Smoke: The amount of smoke present may be insufficient to alarm smoke detectors. Smoke detectors are designed to alarm, at various levels of smoke density. If such density levels are not created by a developing fire at the location of the detector, the detector will not go into alarm.

• Smoldering vs. Flaming Fires: Smoke detectors, even when working properly, have sensing limitations. Detectors that have photoelectric sensing chambers tend to detect smoldering fires better than flaming fires, which have little visible smoke. Detectors that have ionizing-type sensing chambers tend to detect fast flaming fires better than smoldering fires. Because fires develop in different ways and are often unpredictable in their growth, neither type of detector is necessarily best and a given type of detector may not provide adequate warning of a fire.

• False Alarms and Pre-Fire Disconnection: Smoke detectors are subject to false alarms and nuisance alarms and may have been disconnected by users. For example, a smoke detector located in or near a kitchen may go into nuisance alarm during normal operation of kitchen appliances. In addition, dusty or steamy environments may cause a smoke detector to falsely alarm. If the location of a smoke detector causes an abundance of false alarms or nuisance alarms, do not disconnect the smoke detector, call a professional to analyze the situation and recommend a solution.

• Fast Fires and Explosions: Smoke detectors cannot be expected to provide adequate warning of fires caused by arson and children playing with matches

(especially within bedrooms), smoking in bed, violent explosions (caused by escaping gas, improper storage of flammable materials, etc.).

Detectors: Heat detectors do not sense particles of combustion and are designed to alarm only when heat on their sensors increases at a predetermined rate or reaches a predetermined level. Heat detectors are designed to protect property, not life.

FireNET 4127 I & O Manual v1.90 UL

may not alert people or wake up sleepers who are located on the other side of closed or partially open doors. A warning device that activates on a different floor or level of a dwelling or structure is less likely to awaken or alert people. Even persons who are aware may not notice the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffic. Audible warning devices may not alert the hearing impaired (strobes or other devices should be provided to warn these people).

Any warning device may fail to alert people with a disability, deep sleepers, people who have recently used alcohol or drugs, or people on medication or sleeping pills.

• Strobes: Strobes can under certain circumstances, cause seizures in people with conditions such as epilepsy.

• Drills: Studies have shown that certain people, even when they hear a fire alarm signal, do not respond or comprehend the meaning of the signal. It is the property owner’s responsibility to conduct fire drills and other training exercises to make people aware of fire alarm signals and instruct on the proper reaction to alarm signals.

Loss: In rare instances, the sounding of a warning device can cause temporary or permanent hearing loss. alarm signals from a premises to a central station may be out of service or temporarily out of service. For added protection against telephone line failure, backup radio transmission systems are recommended.

• System Failure With Age or Lack of Maintenance: System components, though designed to last many years, can fail at any time. As a precautionary measure, it is recommended that smoke detectors be checked, maintained, and replaced per manufacturer’s recommendations.

• Electrical Power Problems: System components will not work without electrical power. If system batteries are not serviced or replaced regularly, they may not provide battery backup when AC power fails.

• High Air Velocity or Dusty or Dirty Environments: Environments with high air velocity or that are dusty or dirty require more frequent maintenance.

Importance of Maintenance: In general, fire alarm systems and devices will not work without power and will not function property unless they are maintained and tested regularly.

Alarm is Not Substitute for Insurance: While installing a fire alarm system may make the owner eligible for a lower insurance rate, an alarm system is not a substitute for insurance. Property owners should continue to act prudently in protecting the premises and the people in their premises and should properly insure life and property and buy sufficient amounts of liability insurance to meet their needs.

FireNET 4127 I & O Manual v1.90 UL

1.4 Agency Listings, Approvals, Requirements

1.4.1 Federal Communications Commission (FCC)

The FireNET 4127 has been verified to comply with FCC Rules Part 15, Class A

Operation is subject to the following conditions:

1. This device may not cause radio interference.

2. This device must accept any interference received, including any that may cause undesired operation.

1.4.2 Underwriters Laboratories (UL)

The FireNET 4127 is UL864 9 th

Edition listed and is suitable for use as a commercial protected premises control unit as follows:

-Local signaling unit

-Types of signaling services are automatic, manual, waterflow, & sprinkler supervisory.

-Style 4, 6, or 7 for Signaling Line Circuits

-Style Y for Notification Appliance Circuits

-Non-coded signaling

-Central Station Service – DACT type (protected premise)

-Remote Station Service – DACT type (protected premise)

-Proprietary Service – DACT type (protected premise)*

-Auxiliary Service – local energy type (protected premise)

*When used with the Bosch D6600 Digital Alarm Communicator Receiver.

1.4.3 National Fire Protection Association (NFPA)

Install and configure the FireNET system in accordance with NFPA 72 and 13.

All field wiring must be installed in accordance with NFPA 70 National Electric Code

(Article 760).

FireNET 4127 I & O Manual v1.90 UL

Section 2 – Control Panel Installation

2.1 What’s in the Box?

The FireNET 4127 control panel includes the following components and hardware:

Control panel cabinet with hinged door.

Power supply module pre-mounted in cabinet

Control panel annunciator & RS232 interface pre-mounted in cabinet

Main control unit pre-mounted in cabinet.

Two keys for the cabinet lock and two keys for the Enable Controls keyswitch.

Note that the Denver Door build does not include keys for the Enable Controls

keyswitch.

(2) 10k ohm EOL resistors PN# 0400-01046, (4 or 8) zero ohm jumpers PN#

0400-01025, (1) 1N4004S diode PN# 0400-01024, and (4) EOLD devices PN#

0400-1023.

Battery jumper for series connection of 2 – 12 volt batteries.

Installation Manual (

PN# 1700-09948)

2.2 Environmental Specifications

The FireNET 4127 main control panel should be installed in locations where it will NOT be exposed to temperatures outside the range of 32 o

F – 120 o

F or humidity outside the range of 10%-85% non-condensing.

The FireNET 4127 control panel must be installed so that it is not subjected to damage by water and condensation. AVOID mounting the control panel cabinet directly on exterior masonry walls, in areas subject to plumbing leaks, in areas subject to splash from sprinkler test valves, or in high humidity areas.

The FireNET control panel is intended for installation in indoor environments in a dry location.

FireNET 4127 I & O Manual v1.90 UL

2.3 Control Panel Layout

2.3.1 Front Panel Layout, Standard Build

8-Line x 40 character LCD

Front Panel Controls

Figure 2-3-1

Front Panel

Indicators

Enable Controls Key-switch

(Access Level 2)

FireNET 4127 I & O Manual v1.90 UL

2.3.2 Front Panel Layout, Denver Door Build

Figure 2-3-2

Figure 2-3-2a

FireNET 4127 I & O Manual v1.90 UL

2.3.3 Control Panel Annunciator, Control Unit and Power Supply Layout

WARNING!

DO NOT PLUG OR UNPLUG RIBBON CABLES

WHILE BOARD IS POWERED. STATIC

SENSITIVE CIRCUITS. OBSERVE STATIC

HANDLING PROCEDURES AT ALL TIMES

WARNING!

DO NOT PLUG OR UNPLUG RIBBON CABLES

WHILE BOARD IS POWERED. STATIC

SENSITIVE CIRCUITS. OBSERVE STATIC

HANDLING PROCEDURES AT ALL TIMES

Control Panel Annunciator &

RS 232 Interface

Printer Connection

PC Connection

Front Panel Controls

Figure 2-3-3

Main Control Unit

SLC Loops

Programmable Relays

Notification Appliance

Circuits

Programmable Outputs

Remote Control and Aux

Inputs

Expansion Board

Connections

Network Connections

Aux Power Output

Power Supply Module

AC Power Connection

Battery Connection

FireNET 4127 I & O Manual v1.90 UL

2.4 Mounting the Control Panel

Consult the environmental specifications listed in Section 2.2 to determine a suitable location to mount the FireNET 4127 main control panel.

The panel should be mounted so that it is accessible to service personnel and located in a secure area.

Do not mount directly to a concrete wall. Use a suitable standoff material such as plywood to keep condensation away from the control panel.

2.5 Wiring Specifications

Care should be taken when wiring the system to avoid situations that would contribute to inducing electrical noise from one wire to another. Induced noise can interfere with telephone communications or cause erratic system operation. Follow these guidelines to plan your system wiring prior to installation.

• Route high and low voltage wiring separately. Maintain a minimum 2” separation between high and low voltage wiring throughout the building.

• Route control panel wiring around the perimeter of the enclosure. A minimum

.25” separation is required between high and low voltage wiring.

• Identify which group each wire or cable is associated with from the list below.

Isolate each groups wiring as much as possible. Avoid running a single multiconductor cable for multiple groups of conductors.

• AC Power - Main Power Supply

Appliances

Circuits

• Relay

• Voltage

Outputs

• Remote Control and Auxiliary Inputs

• Network Wiring (Shielded wire required)

• RS485 Bus Wiring (Shielded wire required)

• Keep wiring from different groups separated as much as possible. If you must share the same conduit with different conductor groups consider using shielded cable.

• If shielded cable is used terminate the shield to the earth ground terminal block in the main control panel and leave open at field side of cable. Do not ground at both ends of cable.

• All terminals on the FireNET control can accept wire gauges from 22AWG and

14AWG.

FireNET 4127 I & O Manual v1.90 UL

2.5.1 Suggested Routing of AC Power

Route the AC input power wiring as outlined below. Follow recommendations outlined in section 2.5 regarding the separation of high and low voltage wiring.

The preferred entry location for AC input power is via the left side knock-out (see green dotted line above). DO NOT route AC input power across the main control board

(K6002), the ribbon cable interconnects, or directly across or adjacent to the lowvoltage connections made on terminal strips X1 (top) or X2 (side).

FireNET 4127 I & O Manual v1.90 UL

2.6 Battery Calculations

FireNET 4127 I & O Manual v1.90 UL

2.7 Electrical Ratings

Table 2.7.1 (X1) Top Terminal Strip Electrical Ratings for Main Control Unit

Rating

Terminal # and Label Description

Voltage Current

- OUT

+ OUT

- IN

+ IN

- OUT

+ OUT

- IN

+ IN

- OUT

+ OUT

- IN

+ IN

- OUT

+ OUT

- IN

+ IN

SLC 1

SLC 2

SLC 3

SLC 4

Fire 1

Fire 2

Signaling Line Circuit. Out terminals used for

Class B or A wiring.

Signaling Line Circuit. In terminals used for

Return Loop for Class A wiring.

Signaling Line Circuit. Out terminals used for

Class B or A wiring.

Signaling Line Circuit. In terminals used for

Return Loop for Class A wiring.

Signaling Line Circuit. Out terminals used for

Class B or A wiring.

Signaling Line Circuit. In terminals used for

Return Loop for Class A wiring.

Signaling Line Circuit. Out terminals used for

Class B or A wiring.

Signaling Line Circuit. In terminals used for

Return Loop for Class A wiring.

Supervisory Supervisory relay contact.

Auxiliary

Fire condition relay contacts #1.

Fire condition relay contacts #2.

Programmable auxiliary relay contacts.

30VDC

32VDC

NAC 1

Notification Appliance Circuit #1. 10K EOLR

Required.

Notification Appliance Circuit #2. 10K EOLR

Required.

24VDC

2.5 A*

NAC 2

NAC 3

Notification Appliance Circuit #3. 10K EOLR

Required.

24VDC

2.5 A*

NAC 4

Notification Appliance Circuit #4. 10K EOLR

Required.

24VDC

2.5 A*

*Note: See Section 2.8 for additional details regarding NAC circuit ratings

1 A

400mA

FireNET 4127 I & O Manual v1.90 UL

Table 2.7.2 (X2) Side Terminal Strip Electrical Ratings for Main Control Unit

Rating

Terminal # and Label Description

Voltage Current

Fire Routing

Trouble

Routing

Programmable

Output

TBL

RES

INT

CNT

SIL

PR1

PR2

PR3

Supervised fire signaling output

Supervised trouble signaling output

Supervised programmable output

Trouble Input Remote control input

Reset

Input

Intermittent

Input

Continuous

Input

Silence/Ack

Input

Remote control input

DC Ground

Signal for activating remote inputs

Programmable

Input 1

Programmable

Input 2

Programmable

Input 3

Auxiliary input

COMMS

AUX

24V

NETWORK

OUT

RS485 to I/O boards

Auxiliary 24V supply

RS485 to other panels

24VDC

12VDC

24VDC

12VDC

500mA

30mA

500mA

30mA

100mA

500mA

100mA

FireNET 4127 I & O Manual v1.90 UL

Table 2.7.3 Terminal Strip Electrical ratings for the Power Supply Module

Rating

Connector Terminal Description

Voltage Current

TB6

TB4

TB3

+24VDC

DC RTN

Earth Ground

AC Neutral

AC Line

+ DC Output

- DC Output

+ Battery

- Battery

N/A

120 VAC, 50/60Hz

240 VAC, 50/60Hz

120 VAC, 50/60Hz

240 VAC, 50/60Hz

+24 VDC

DC Common

+24 VDC

DC Common

N/A

2.1A

1.1A

2.1A

1.1A

0 - 4 Amps

NOTE: Earth ground fault detection impedance is approximately 15K ohms between earth ground and the FireNET internal floating DC supply.

FireNET 4127 I & O Manual v1.90 UL

2.8 Specifications

Primary AC: 120VAC @ 2.1 amps 50/60hz (or) 240VAC @ 1.1 amp

50/60hz

24VDC @ 4 amps Output DC:

Power Supply: 4 amp integrated

Max Charger Current: 1.5 amps

Dimensions:

Weight:

Color:

14.5”W x 24” H x 5”D

31 lbs (without batteries)

Red (optional charcoal)

Display: 8 line x 40 character LCD (320 characters total)

Zones: 500 network wide software zones per system (Output zones allocated to zones 1 to 253 only for SOM 2.0 and earlier)

2 or 4 (class A or B) SLC loops:

Devices per Loop: 127 sensors & modules, plus 127 analog sounder bases,

254 total

Addresses per Panel (800 addresses + sub-addresses max per panel)

NAC Outputs: (4) 2.5 amp@24VDC (class B)*

Relay Outputs:

Voltage Outputs:

Aux. Power:

Aux. Inputs:

PC Port:

Printer Port:

(5) Form C contact 1amp@30VDC

(3) 500mA@24VDC

500mA@24VDC

(8) digital pull downs

RS232

RS232 or later have NAC circuits rated at 2.5AMPS each. All

FireNET panels dated earlier than 1/24/05 with s/n prior to

411-00412 have NAC circuits rated at 1.6AMPS each.

FireNET 4127 I & O Manual v1.90 UL

Section 3 - Power Supply and Main Control Unit Connections

3.1 AC Power Connection

The AC power connection terminals are located in the lower left hand corner of the power supply module. (See Figure 3.3) Observe the wiring polarity and connect as shown. Local electrical codes may require that a licensed electrician make these connections.

NFPA 72 requires that the AC connection be made from a dedicated branch circuit that is mechanically protected. The circuit must be marked in red and identified as a “FIRE

ALARM CIRCUIT”. The location of the circuit and its disconnecting means shall be permanently noted at the fire alarm control panel. The circuit breaker must be rated at

20 amps maximum.

Fuse Replacement: To replace the power supply fuse F2, power down the fire system by removing the AC power first, then disconnect the backup batteries to the fire alarm control panel. Remove the blown fuse and replace with a 3A 250VAC, slow blow,

5X20mm fuse. When the fuse replacement is completed, restore AC power to the control panel and connect the back up batteries observing polarity of connections.

3.2 Battery Connection

The FireNET 4127 fire alarm control panel can charge up to 60AH batteries. Up to 17

AH will fit in the control panel enclosure, as well as larger sizes that have the same size footprint as 17AH batteries. Batteries larger than 17AH may be mounted remotely in the

FN-ACC accessory cabinet. Use the current draw and battery calculation worksheet in section 2.6 to determine the appropriate size battery to use.

Two battery leads come pre-connected to the power supply module. Connect two 12volt batteries in series to the battery leads as shown in Figure 3.3. Both batteries must be of the same AH rating. Do not try to parallel multiple batteries together to obtain a higher AH rating. Use only UL Recognized Sealed Lead Acid Batteries.

Fuse Replacement: To replace the in-line battery fuse, remove the battery lead (RED) from the positive battery terminal and twist the bayonet fuse holder to open. Remove the blown fuse and replace with a “Bussman AGC-10” (10A) type fuse or equivalent.

Reassemble bayonet fuse holder and attach the battery lead to the + terminal of the battery.

NOTE:

The standby batteries cannot power the system until the main

120VAC power has been established. Once the system has been initially powered from them 120VAC source the batteries will operate the system in the event of a power failure.

FireNET 4127 I & O Manual v1.90 UL

3.3 Auxiliary Power Connection

24 VDC auxiliary power is available on the main control unit X2 terminal strip from terminals 18 and 19. (See Figure 3.4) This auxiliary power is intended to run expansion boards or other low current auxiliary devices.

The total output from the Auxiliary Power terminals must not exceed .500 amps.

Any devices powered from the auxiliary power terminals should be entered into Table

2.6 and taken into consideration for standby battery size.

Figure 3.3 Four-Amp Power Supply Detail

FireNET 4127 I & O Manual v1.90 UL

Main

Control

Unit

Top Terminal Strip

Side Terminal Strip

+ -

NAC 1

+ -

NAC 2

+ -

NAC 3

+ -

NAC 4

FIRE

ROUTING

TROUBLE

ROUTING

ADDITIONAL

I/O BOARDS

PROGRAMMABLE

OUTPUT

1. TBL

2. RES

3. INT

4. CNT

REMOTE

CONTROL

AND AUX.

INPUTS

5. SIL

6. PR1

7. PR2

8. PR3

COMMS

AUX

24V

NETWORK

OUT

AUX 24VDC Power 500mA Max

Used for expansion boards and low current auxiliary devices

(See Section A.4 for compatible

24VDC Devices)

Figure 3.4 Auxiliary Power Connection Detail

FireNET 4127 I & O Manual v1.90 UL

3.4 Notification Appliance Circuit Connection

• NAC output rated @ 2.5 Amp each.

• See Appendix A.3 for compatible NAC Devices.

• See Section 8 and 9 of this manual for programming.

Top Terminal Strip

Class B (Style Y) - For Indicating Devices

H/S

Hochiki America

EOL Device

(EOLD)

P/N 0400-01023

(Supervised)

Main

Control

Unit

+ -

NAC 1

+ -

NAC 2

ADDITIONAL

I/O BOARDS

+ -

NAC 3

+ -

NAC 4

FIRE

ROUTING

TROUBLE

ROUTING

PROGRAMMABLE

OUTPUT

1. TBL

2. RES

3. INT

4. CNT

REMOTE

CONTROL

AND AUX.

INPUTS

5. SIL

6. PR1

7. PR2

8. PR3

COMMS

AUX

24V

Figure 3.5 Notification Appliance Circuit Connection Detail

FireNET 4127 I & O Manual v1.90 UL

3.5 Voltage Routing and Relay Output Connection

3.5.1 Voltage Routing Outputs

• Outputs are fully programmable.

• Outputs are rated @ 500mA Max.

• Outputs are polarity reversing.

• See Appendix A.4 for compatible devices.

• See Section 8 and 9 of this manual for programming.

+ -

N AC 1

+ -

N AC 2

+ -

N A C 3

+ -

N AC 4

FIR E

R OU TIN G

TR O UB LE

R OU TIN G

M ain C ontrol

U nit

P RO G RA M M AB LE

O U TP UT

1. TBL

2. R ES

3. IN T

4. C N T

R EM O TE

CO N TR O L

A ND AU X.

IN PU TS

5. S IL

6. PR 1

7. PR 2

8. PR 3

C O M M S

AD D IT IO N AL

Figure 3.6 Voltage Routing Outputs Detail

X 2

EX A M PLE O F F IR E R O U TIN G , T R O U B LE

R O UT IN G , & P R O G RA M M A B LE O U TP U T

PO LAR ITY

R EVER SIN G D EVIC E

500 m A @ 24VD C m ax.

1 0K O H M

E N D-O F-LIN E

R E SISTO R (EO LR )

P /N 040 0-010 46

(Supervised)

10K O HM EN D -O F-LIN E R E SIS TO R (E O LR )

P/N 0400-01046 (S upervised)

1N 4004S E N D-O F-LIN E D IO DE (E O LD )

P /N 0400-01024 (S upervised)

FireNET 4127 I & O Manual v1.90 UL

3.5.2 Relay Outputs

• Relays are fully programmable except for the supervisory relay.

• The auxiliary relay defaults to reset function that can be used to reset conventional devices requiring power reset. This inherent function is negated when the auxiliary is assigned a function.

• Relays are dry form “C” contacts.

• Fire 2 Relay can optionally be programmed as an AC Fail relay with a delay value.

• See section 8 and 9 of this manual for programming.

Main Control

Unit

Conventional Relay Contacts rated for 1A @ 30VDC.

Must be connected to power limited source.

(Not Supervised) (Resistive)

NC C NO

FIRE 1

NC C NO

TROUBLE

NC C NO

FIRE 2

NC C NO

SUPERVISORY

NC C NO

AUXILIARY

+ -

NAC 1

+ -

NAC 2

Figure 3.7 Relay Outputs Detail

FireNET 4127 I & O Manual v1.90 UL

3.6 Digital Input Connection

• Digital Inputs are fully programmable.

• Digital Inputs are for secondary use only.

• Digital Inputs are pull-down type.

• Digital Inputs are not supervised.

• Digital Inputs are not intended for use with primary initiating devices for fire conditions.

• These inputs are activated via N.O. dry contact or switch by connecting terminal

12 on X2 to the input.

• See Section 8 and 9 of this manual for programming.

+ -

NAC 1

+ -

NAC 2

+ -

NAC 3

+ -

NAC 4

FIRE

ROUTING

TROUBLE

ROUTING

Main Control Unit

PROGRAMMABLE

OUTPUT

1. TBL

2. RES

3. INT

4. CNT

REMOTE

CONTROL

AND AUX. INPUTS

5. SIL

6. PR1

7. PR2

8. PR3

COMMS

Figure 3.8 Remote Control Input Connection Detail

DIGITAL INPUTS

USE DRY CONTACTS ONLY

(EXAMPLE FOR INPUTS 1-8)

(Not Supervised)

FireNET 4127 I & O Manual v1.90 UL

3.7 Using a Printer

The FireNET panel will support a local serial printer. The printer connects to the J10

RS-232 port (labeled Printer) on the inside of the front door. J10 is located in the bottom left-hand corner of the circuit board. The printer cable must be no longer than

20 feet in length. The printer can be used for real-time logging of events. It can also be used to print the panel’s configuration (see section 8.2.4) or to print the panel’s history log (see section 10.2.2).

Serial Printer Properties:

Baud

Bits

Parity

Bit

FireNET 4127 I & O Manual v1.90 UL

Section 4 – Expander Board Installation

4.1 Compatible Expander Boards

The following Hochiki America Corp. expander boards are listed as compatible with the

FireNET 4127 analog addressable fire alarm system.

Expanders

• FN-4127-SLC - Dual SLC Loop Expander (Local FACP Expander)

• FN-4127-IO – 16 Channel Input/Output Board (RS-485 Bus Device)

• FN-LCD-S Serial LCD Annunciator (RS-485 Bus Device)

This section covers the installation of the devices listed above. For proper operation each of these devices must be programmed from the FireNET front panel, or by using the Loop Explorer software. Please refer to Sections 8 and 9 of this manual for more information on programming the functionality of expander boards.

FireNET 4127 I & O Manual v1.90 UL

4.2 General Installation of RS-485 Bus Devices

4.2.1 Wiring Distance and Mounting Locations

RS485 bus devices can be mounted either in the main control panel on the standoffs provided to the right of the control unit, or in an accessory cabinet (FN-ACC). When mounting remotely in an accessory cabinet the distance from the panel to the RS485 bus device must not exceed 4000 feet. A suitable communications cable for RS485 applications must be used for the RS485 bus devices.

Specific wiring connections for each device are included later in this section. For specific wiring distance, connections, and mounting of the FN-LCD-S serial LCD

Annunciator, see Section 4.7.

FireNET 4127 I & O Manual v1.90 UL

4.2.2 Addressing

Up to 32 RS485 bus devices can be added to the system. Each RS485 bus device must be set to a unique address 1-32.

The address for each RS485 bus device is set using a position DIP-switch in binary fashion. Switches 1-5 represent the values 1, 2, 4, 8, and 16, respectively. Switch 6 is not used. To set the address, move only the switches whose values when added equal the address value you wish to set, to the “ON” position. For example moving switches 1 and 3 (whose values are 1 and 4 respectively) to the “ON” position sets the address of

5 into the RS485 bus device. See the other examples below:

ADDRESS 1

ADDRESS 5

ADDRESS 21

Shows switch actuator in the ON position.

Switch Number – 1 2 3 4 5 6

Addresses must be set with no power applied to the system.

Value – 1 2 4 8 16 not used

4.2.3 Terminating

The last board connected to the RS485 bus must have a terminating jumper installed at position J3 as shown in figure

4.2.3.1

Even if only 1 RS485 bus device is connected to the panel this jumper must be installed.

Jumper J3

LED1

LED2

LED3

S1 TR1

U7 SD1

J2 J3 J4

D17

Figure 4.2.3.1

FireNET 4127 I & O Manual v1.90 UL

4.2.4 Power Connections

All RS485 bus devices require 24 VDC to operate. The AUX 24V terminals of the FN-

4127 can supply this voltage (500 milliamps maximum) or you may use an external power supply that provides 24 VDC output.

Connections are provided on each RS485 bus device for both incoming and outgoing power.

4.2.5 COMMS Connection

In addition to power, each RS485 bus device requires a pair of conductors for data communication. This wiring is connected to the COMMS + and - terminals on the FN-

4127 control panel or can be connected to the COMMS OUT + and - terminals of another RS485 bus device.

+ -

NAC 1

+ -

NAC 2

+ -

NAC 3

+ -

NAC 4

FIRE

ROUTING

TROUBLE

ROUTING

PROGRAMMABLE

OUTPUT

1. TBL

2. RES

3. INT

REMOTE

CONTROL

AND AUX.

INPUTS

4. CNT

5. SIL

6. PR1

7. PR2

8. PR3

COMMS

ADDITIONAL

I/O BOARDS

AUX

24X

NETWORK

OUT

J1 U1

LED

S1 TR1

U7 SD1

D17 +

TO NEXT I/O

BOARD

FireNET 4127 I & O Manual v1.90 UL

4.3 FN-4127-IO - Input / Output Board

In addition to the basic 508 points that the FireNET 4127 can accommodate on the SLC loops additional input and output points can be added by using FN-4127-IO

Input/Output boards on the RS485 bus.

The FN-4127-IO has 16 channels. Each channel can be individually configured as either an input or an output. Up to 32 FN-4127-IO boards can be connected to the system via the RS485 bus giving the system an additional 512 inputs/outputs.

4.3.1 Configuring Inputs

Inputs to the FN-4127-IO are optically isolated and connected to the board by installing a normally open contact with a resistance no greater than 500 ohms to any input and a terminal marked 0V. The current switched by the contact will be a maximum of 3 milliamps.

NOTE:

Inputs on the I/O board are not supervised. These inputs are not for primary initiating or detection of fire or life safety conditions.

These inputs are for programmable for secondary use only, and not used for signaling Fire, Supervisory, or Trouble conditions. All primary initiating or detection inputs must be connected to applicable SLC devices listed for fire. See Section 5 of this manual for SLC devices.

FireNET 4127 I & O Manual v1.90 UL

4.3.2 Configuring Outputs

When configured as outputs, the I/O board channels supply a negative voltage (with respect to the I/O board 24V power supply) via a transistor.

Because transistor elements can be damaged by excessive current drain, great care should be taken when connecting to outputs. Particular care should be taken to ensure that suppression diodes on relay coils are correctly polarized. Wrongly connected diodes will damage the outputs. Diodes should be connected with the band to the positive 24V.

Individual channels can supply current up to 100 milliamps but this must be limited to 500

2.2k

milliamps for each bank of eight (500 milliamps for 1-8 and 500 milliamps for 9-16).

The power supply to the I/O board should also be considered to ensure that its rating is not exceeded if multiple channels are switched on. Overall current draw for the

I/O board is 1010mA max.

NOTE:

Outputs on the I/O board are not supervised. These outputs are not for primary notification of fire conditions (i.e. not for use as NAC circuits). These outputs are for secondary use only. All primary notification output devices must be connected to applicable NAC circuits on the FireNET panel. See Section 3.4, Appendix A, and B for details on NAC circuits and compatible NAC devices.

When powering the I/O board from the FireNET Aux 24VDC power (limited to 500ma), the following maximum wiring distances apply at the gauges noted:

Wire Distance

18AWG 875ft

16AWG 1400ft

14AWG 2300ft

When powering the I/O board from a separate Aux 24VDC UL Fire listed supply the maximum voltage drop cannot exceed 4VDC.

FireNET 4127 I & O Manual v1.90 UL

4.3.3 LED Indicators

LED indicators on the I/O board give some simple diagnostic information and show that the boards are communicating with the control panel. The red LED (LED1) is on during receipt of a message from the control panel and will turn off if the I/O board feels the communication is normal.

• If the LED is flickering more or less continuously - the board is operating normally.

• If this LED is not lit - the board is not receiving data from the control panel and the comms connection should be checked.

• If this LED is permanently lit - then it is likely that data is being received but that it is being corrupted. In this case the quality of the comms connection should be checked for interference from mains or other noise generating sources.

The yellow LED (LED2) will flicker briefly every few seconds when the I/O board responds to the main panel. If this LED does not flicker then it is not responding to the control panel and the comms connection should be checked.

LED 1

LED 2

4.4 Reserved for Future Use

4.5 Reserved for Future Use

C12

C13

R44 R42 R40 R18

OP4

R45

R52

R53

R16

R43

R50

R51

R14

R41

R48

OP3

R49

OP1

OP2

R12

R39

R46

R47

R10

R17 R15 R13 R11

D10

D11

D12

D13

D14

D15

D16

D18

LED1

LED2

LED3

S1 TR1

U7 SD1

J2 J3 J4

D17 +

FireNET 4127 I & O Manual v1.90 UL

4.6 FN-4127-SLC – Dual SLC Loop Expander

The FN-4127 FireNET control panel is provided with two SLC Loops, however an additional two SLC Loops may be added at the factory or a later date if required through the use of a FN-4127-SLC expander board.

The main control unit has terminations for connecting all four SLC loops, but on the basic 2-loop control panels not using an SLC loop expander there is no circuitry for

SLC loops 3 & 4. The FN-4127-SLC dual loop expander board adds circuitry for loops 3

& 4.

4.6.1 Installation of the FN-4127-SLC

1. To install the additional SLC Loops, the control panel must have its 120V AC line and battery power removed.

2. The metal cover on the terminal board should be removed by loosening the single screw in the center of the cover.

3. The circuit board containing the additional loop circuits is supplied in a static dissipative bag and should remain in this bag until it is to be installed.

NOTE:

As with all electronic components, this circuit board is very sensitive and can be easily damaged by electrostatic discharge.

4. The loop board mounts on the left hand side of the terminal board and fits upside down compared with the existing circuit. The additional 2-loop circuit board is supplied with 2 ribbon cables of different sizes and the board should be oriented so that the ribbon cables match the connectors.

5. Install the four mounting standoffs to the main board, then attach the additional

2-loop board using the M3 screws and fiber washers.

6. After checking that the new circuit board is properly installed and making good contact with its connectors, the metal cover should be replaced. Connect the

SLC loop wiring, then re-apply power to the control panel.

7. Unused detection circuits must have the "loop + out" to "loop + in" and "loop - out" to "loop - in" terminals wired together to prevent open circuit troubles from being reported. Class B SLC circuits also require the 0 ohm jumpers to be installed – please see Section 5.3.1.

Once the detection circuits have been connected, the devices for the new detection circuits can be automatically detected using the auto learn feature from the menu on the control panel (see Section 8 of this manual).

FireNET 4127 I & O Manual v1.90 UL

uid Cryst tal Displa ciator

buss that is designa can be con nected via RS485 ser rial port to a o el.

of the FN-LCD-S

e mounted vironmental installation ions. The so that it is tions. e personnel ed wall. Use a suitable e om his manual.

. The FNhe main pa nel operato and controls.

Figure 4.

.7.2 FN-LC D-S Serial unciator

FN-LCD-S fr rom the Fire wer (limited t or wiring distances apply to the

1000 ft t. 6

2000 ft t. 3

3000 ft t. 2

4000 ft t. 1

Manual

Figure 4.7.3 FN-LCD-S Wiring Detail

FireNET 4127 I & O Manual v1.90 UL

NOTE:

When connecting I/O boards to the FN-LCD-S via the COMMS terminals shown above, the I/O boards must be powered by a

UL864/1481 listed local Auxiliary 24VDC power supply, or the Aux

24VDC output of the FN-LCD-S within the limits outlined below.

DO NOT connect the I/O board power input to the Aux 24VDC output terminals of the

FN-LCD-S unless the sum current load of the I/O board is within the 500mA max

24VDC output rating of the FN-LCD-S and within the 500ma max 24VDC output rating of the FN-4127 control panel that provides power to the FN-LCD-S. Failure to make this consideration may result in overloading the FN-LCD-S and/or the control panel

Aux 24VDC output (500ma max. each).

The current limits during both standby and in alarm shall not exceed the 500mA rating of the FN-4127 Panel Aux 24VDC output or FN-LCD-S.

The FN-LCD-S current draw is rated as follows:

Standby: 20mA @ 24VDC

Alarm: 110mA @ 24VDC

Available colors are RED and CHARCOAL as identified below:

FN-LCD-S-R = RED

FN-LCD-S-C = CHARCOAL

FireNET 4127 I & O Manual v1.90 UL

Section 5 – SLC Device Installation

5.1 Compatible SLC Devices

The following Hochiki America Corp. SLC devices are listed as compatible with the

FireNET 4127 analog addressable fire alarm system.

Detectors (Sensors)

•

ALK-V / ALK-V2 Analog Photoelectric Smoke Detector

•

ALG-V Analog Photoelectric Smoke Detector

•

AIE-EA Analog Ionization Smoke Detector

•

ATG-EA Analog Heat Detector

•

ACA-V Analog Photoelectric and Heat Multi Detector

•

DH98-A Analog Duct Smoke Detector, no Relay

• DH98-AR Analog Duct Smoke Detector with Relay

Smoke sensors will undergo automatic sensitivity testing and verification every 24 hours.

Modules

•

DCP FRCME-4 Addressable Input Module

•

DCP FRCME-S, FRCME-M Mini Addressable Input Module

(with Terminal Blocks)

• DCP FRCMA Class A Addressable Input Module

• DCP FRCMA-I Class A Addressable Input Module

(with SCI)

•

DCP R2M, R2ML, R2MH Addressable Dual Relay Module

•

DCP R2ML-I, R2MH-I Addressable Dual Relay Module

(with SCI)

• DCP SOM Addressable Supervised Output module

• DCP SOM-A Addressable Class A Supervised Output Module

• DCP SOM-AI Addressable Class A Supervised Output Module

(with SCI)

• DCP SCI Short Circuit Isolator

• DCP DIMM Dual Input Monitor Module

FireNET 4127 I & O Manual v1.90 UL

• CZM Conventional Zone Module

• ASB Analog Sounder Base

• SOM-R

(Preaction Sprinkler Systems)

NOTE:

The “DCP” prefix listed above on several devices indicates the device’s formal model name as specified by Underwriters Laboratories within each device’s individual listing. The “DCP” prefix will be dropped throughout the body of this manual and the shortened model name will be used. Please take note of this when referencing these devices within this manual.

FireNET 4127 I & O Manual v1.90 UL

5.2 Number of Devices

The FireNET 4127 comes with 2 SLC loops built-in to the panel. Each loop can support up to 127 analog addressable detectors and modules as well as 127 analog sounder bases for a total of 254 possible per loop. By adding the FN-4127-SLC expander card,

2 additional SLC loops can be added to the panel for a total of 4 loops.

Addresses 1 – 127 are reserved for any combination of detectors and modules.

Addresses 128 – 254 are reserved for analog sounder bases. Detectors and modules cannot be addressed to the upper address 128 - 254. Each device on the SLC loop must have a unique address. Refer to section 5.4 for instructions on programming the address into each analog addressable device.

5.3 SLC Loop Wiring

The FireNET 4127 uses the patented Hochiki DCP Digital Communication Protocol to communicate with each of the analog addressable devices located on the SLC loops.

This extremely fast and reliable protocol allows the use of standard non-twisted, nonshielded wiring for the SLC loops.

The SLC loop wiring may be any solid or stranded cabling that meets the requirements for power limited fire protective signaling circuits listed in NFPA 70 (National Electrical

Code) Article 760. The wiring resistance on the SLC loop must be less than 50 ohms.

Loop capacitance must be less than 1

μF. Loop inductance must be less than 1mH.

The SLC loop terminals are located on the upper left hand corner of the main control board. See Figure 5.3.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT IN

LOOP 1

OUT

LOOP 2

OUT

LOOP 3

OUT

LOOP 4

MAIN CONTROL UNIT

Figure 5.3 SLC Loop Terminals

FireNET 4127 I & O Manual v1.90 UL

5.3.1 Class B SLC Loop Wiring Distance

Refer to Figure 5.3.1 to determine the maximum distance an analog addressable detector or module is allowed to be located from the control panel for Class B SLC loops. The total wire length of all branches of the SLC loop must not exceed 40,000 feet using #14 AWG. When using a Class B SLC wiring configuration, be sure that the

0 ohm jumpers supplied with the panel are properly installed between –OUT to –IN and

+OUT to +IN (Hochiki part # 0400-01025).

Figure 5.3.1 Maximum Wiring Distance for Class B SLC Circuits

FireNET 4127 I & O Manual v1.90 UL

5.3.2 Class A SLC Loop Wiring Distance

Refer to Figure 5.3.3 to determine the maximum distance an analog addressable detector or module is allowed to be located from the control panel for Class A SLC loops.

Class A

Style 6 or 7

SLC Loop

NOTE: For Details on Style 7, refer to Section 5.14.1

Calculate total loop length out and back to determine appropriate wire gauge for Class A SLC loops

Wire Guage

18 AWG

16 AWG

14 AWG

Maximum Wire Length From Control Panel

Out and Back to Control Panel

3900 Feet

6200 Feet

10,000 Feet

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9

OUT

LOOP 1 LOOP 2 LOOP 3

OUT

LOOP 4

MAIN CONTROL UNIT

Figure 5.3.2 Maximum Wiring Distance for Class A SLC Circuits

FireNET 4127 I & O Manual v1.90 UL

Additional Notes Regarding Class A Style 6 and Style 7 SLC loops:

• No t-taps are allowed on Class A SLC loops.

• The return side of the loop must be routed separately from the outgoing loop.

• The return side may not share the same conduit or cable as the outgoing side of the SLC loop.

• When using Class A Style 7 wiring, the SCI Short Circuit Isolator must be installed before and after each analog addressable device on the SLC loop. The wiring from the control panel to the first SCI and from the last SCI back to the control panel must be in conduit. Refer to Section 5.14 for more information on installing the SCI module and for installation method to satisfy Style 7 criteria per NFPA 72.

• Refer to NFPA 72 for additional requirements of Class A circuits.

5.4 Addressing Devices

Prior to installation, all of the addressable devices installed on each of the FireNET

4127 SLC loops must be programmed with a unique address ranging from 1 to 127.

The analog sounder bases will automatically derive their address from the host sensor

(detector) attached to them. The ASB address will be the sensor address + 127 (i.e. N

+ 127). Example: The sensor address is 36. 36 +127 = 163. The ASB will have an address of 163. This address is what the FireNET 4127 control panel uses to identify each addressable device and control its functionality. All Hochiki addressable devices come from the factory preset to address 127. This preset address can be reprogrammed using the Hochiki TCH-B100-NS programmer. Follow these instructions to set/reprogram the address.

1. Identify each analog addressable device that will be installed on an SLC loop and label it with a unique address ranging from 1 to 127.

2. Using the Hochiki TCH-B100-NS programmer as shown in Figure 5.4, program the appropriate address into each analog addressable device.

FireNET 4127 I & O Manual v1.90 UL

Figure 5.4 Hochiki TCH-B100-NS Programmer Connections

1. ASB Automatically derives its address from host sensor (N + 127).

2. Devices must not be powered when using the TCH-B100-NS programmer to set addresses.

3. Mini-modules such as the FRCME-S and FRCME-P should not be connected to the SLC loop when using the TCH-B100-NS programmer to set addresses.

4. When programming the AMS, use the same method as the 4-S type addressable modules.

FireNET 4127 I & O Manual v1.90 UL

5.4.1 Detector Addressing

This section applies to the following Hochiki analog detectors – ALK-V, ALK-V2, ALG-

V, AIE-EA, DH-98, ATG-EA, and ACA-V. Follow these steps to program a new address into any one of these analog detectors. (Refer to Figure 5-4)

1. Twist an analog detector head on to the programmer terminals.

2. Press the left gray button to turn on the programmer and read/display the current address in the detector head. (Factory default is address 127)

3. Using the left gray button you can increase the tens digit one number at a time.

Using the right gray button you can increase the ones digit one number at a time. Using these buttons change the displayed address to the appropriate value.

4. Press the red button to store the displayed address into the detector head.

5.4.2 4-S Module and AMS Addressing

This section applies to the following Hochiki addressable modules - FRCME-4, FRCMA,

FRCMA-I, R2M (all models), DIMM, CZM, SOM (all models), and AMS. Follow these steps to program a new address into any of these addressable modules. (Refer to

Figure 5-4)

1. Using the dual-end programming plug provided with the programmer, plug one end into the jack on the programmer and plug the other end into the programming plug located on the front of the module plate. The plug is nonpolarized and can be connected in either orientation.

2. Press the left gray button to turn on the programmer and read/display the current address in the module.

3. Using the left gray button you can increase the displayed address 10 numbers at a time. Using the right gray button you can increase the displayed address one number at a time. Using these buttons change the displayed address to the appropriate value.

4. Press the red button to store the displayed address into the addressable module.

FireNET 4127 I & O Manual v1.90 UL

5.4.3 Mini Module Addressing

This section applies to the Hochiki FRCME-S, FRCME-P and FRCME-M addressable mini-module. Follow these steps to program a new address into any of these addressable modules. (Refer to Figure 5-4)

1. Using the single ended programming plug, plug the end with the jack on it into the programming jack on the programmer. The programming plug with alligator clips may also be used.

2. Connect the Red wire of the single ended programming plug into the terminal labeled S (IN) on the addressable module. Connect the Black wire of the single ended programming plug into the terminal labeled SC (IN) on the addressable module.

3. Press the left gray button to turn on the programmer and read/display the current address in the module.

4. Using the left gray button you can increase the displayed address 10 numbers at a time. Using the right gray button you can increase the displayed address one number at a time. Using these buttons change the displayed address to the appropriate value.

5. Press the red button to store the displayed address into the addressable module.

FireNET 4127 I & O Manual v1.90 UL

5.5 Smoke and Heat Detector Wiring

This section includes wiring instructions for connecting the following analog detectors to the FireNET 4127 fire alarm control panel: ALK-V / ALK-V2 Photoelectric Smoke

Detector, ALG-V Photoelectric Smoke Detector, AIE-EA Ionization Smoke Detector,

ATG-EA Heat Detector, ACA-V Multi Detector. All FireNET analog detectors must be installed using a YBN-NSA-4 four-inch detector base, or a HSB-NSA-6 six-inch detector base.

For detailed instructions on the physical mounting of FireNET analog smoke and heat detectors please refer to the installation instructions that are included with each analog detector.

Prior to installing any analog detector or module you must set its address as described in section 5.4.

Wire the analog smoke and heat detector bases as indicated in Figure 5.5.

YBN-NSA-4 Four Inch Detector Base Shown

Follow same instructions for HSB-NSA-6 Six Inch Base

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

- +

OUT

- +

LOOP 1

- +

OUT

- +

LOOP 2

- +

OUT

- +

LOOP 3

- +

OUT

- +

LOOP 4

MAIN CONTROL UNIT

Figure 5.5 Analog Detector Base Wiring

To next SLC detector or module

FireNET 4127 I & O Manual v1.90 UL

5.6 Analog Duct Detector Wiring

This section includes wiring instructions for connecting the DH98-A analog duct detector, and the DH98-AR analog duct detector with relay, to the FireNET 4127 control panel SLC loop.

For detailed instructions on the physical mounting and wiring of FireNET analog duct detectors please refer to the installation instructions that are included with each device.

Prior to installing any analog detector or module you must set its address as described in section 5.4. You will need to remove the smoke detector head from the base in the duct detector in order to program it.

FireNET 4127 I & O Manual v1.90 UL

Duct Detector Model #

Operating Voltage

Detector Head Model

Detector Head Type

Sensitivity Test Method

DH98-A

DCP Powered Loop

ALG-V

Analog Photoelectric

Control Panel

To next SLC device

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

- +

OUT

- +

LOOP 1

- +

OUT

- +

OUT

LOOP 2

- +

LOOP 3

- +

OUT

- +

LOOP 4

Remote LED 24 VDC

@ .008 amps max

MAIN CONTROL UNIT

Figure 5.6.1 DH98-A

5.6.1 DH98-A Analog Duct Detector

Connect the DH98-A analog duct detector to the FireNET 4127 control panel SLC loop as shown in Figure 5.6.1.

Terminals 3 and 4 can be used to power a remote alarm LED. The ratings on these terminals are 24 VDC at .008 amps maximum. Please note the number of alarm LED’s that can be illuminated at one time is limited to 5 addresses per SLC loop by the control panel.

NOTE:

The duct sensor LED and remote LED output only activate momentarily when in alarm.

FireNET 4127 I & O Manual v1.90 UL

Duct Detector Model #

Operating Voltage

Detector Head Model

Detector Head Type

Sensitivity Test Method

DH98-A

DCP Powered Loop

ALG-V

Analog Photoelectric

Control Panel

+24V

+REM

LED-

To 24VDC auxiliary power from control panel or external power supply.

24VDC Power is not

Supervised. An EOL Relay must be used at the end of line. The EOL relay must be monitored for power loss trouble.

To next SLC device

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

- +

OUT

- +

LOOP 1

- +

OUT

- +

LOOP 2

- +

OUT

- +

LOOP 3

- +

OUT

- +

LOOP 4

Relays for fan shutdown and auxiliary functions rated at

10.0A @ 250VAC

MAIN CONTROL UNIT

Figure 5.6.2 DH98-AR

5.6.2 DH98-AR Analog Duct Detector with Relay

Connect the DH98-AR analog duct detector with relays, to the FireNET 4127 control panel as shown in Figure 5.6.2.

In addition to the SLC loop connections, the DH98-AR requires 24-volt reset-able auxiliary power (10mA standby and 55mA alarm) connected to terminals 3+ and 4-.

This power may come from the FireNET 4127 main control panel auxiliary power (500 mA max.) connections (terminals 18 and 19) or from an external power supply.

The DH98-AR analog duct detector contains 2 sets of form C alarm contacts rated at

10.0 amps @ 250 VAC that can be used for fan shutdown and other auxiliary functions.

In addition to the alarm contacts the DH98-AR also has connections for a remote test switch as well as outputs for a remote alarm and remote pilot light LED’s.

NOTE

: Test switch only activates output relays, and does not place the detector into alarm.

FireNET 4127 I & O Manual v1.90 UL

5.7 FRCME-4 Input Module Wiring

The FRCME-4 input module is used to connect standard normally open dry contact types of fire alarm devices such as pull stations, waterflow, or tamper switches to the

FireNET 4127 SLC loop. More than one switch can be connected to a FRCME-4 however you must not mix multiple switch types on a single FRCME-4. For example:

three waterflow switches connected to a single FRCME-4 is acceptable. However, two waterflow switches and one valve tamper switch connected to a single FRCME-4 is not.

NFPA and local codes may also apply.

The FRCME-4 must be programmed with a unique address from 1-127. All of the switches connected to a single FRCME-4 appear at the main control panel as a single address. Please refer to section 5.4 of this manual for instructions on programming an address into the FRCME-4 input module.

Connect the FRCME-4 to the FireNET as shown in figure 5.7.1. Refer to the installation instructions included with the FRCME-4 for more detailed installation and wiring instructions.

UL Listed EOLR

(10K OHM)

Part # 0400-01046

To next SLC Device -

IN-B

IN-A

SC -

S +

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT

LOOP 1 LOOP 2 LOOP 3 LOOP 4

MAIN CONTROL UNIT

Figure 5.7.1 FRCME-4 Input Module Wiring Detail

FireNET 4127 I & O Manual v1.90 UL

5.8 FRCME-S Mini Input Module (w/ Terminal Blocks)

The FRCME-S input module is used to connect standard normally open dry contact types of fire alarm devices such as manual pull stations to the FireNET 4127 SLC loop.

The FRCME-S must be programmed with a unique address from 1-127. All of the dry contact type devices connected to a single FRCME-S appear at the main control panel as a single address. Please refer to section 5.4 of this manual for instructions on programming an address into the FRCME-S input module.

Connect the FRCME-S to the FireNET as shown in figure 5.8.1. Refer to the installation instructions included with the FRCME-S for more detailed installation and wiring instructions.

UL Listed EOLR

(10K OHM)

Part # 0400-01046

To next SLC Device

IN-B

IN-A

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT

LOOP 1 LOOP 2 LOOP 3 LOOP 4

MAIN CONTROL UNIT

Figure 5.8.1 FRCME-S Mini Input Module (w/ Terminal Blocks) Detail

NOTE: The FRCME-S is approved to UL 864 8 th

edition. However, the FRCME-S will operate with the 9 th

edition approved FireNET Fire Alarm Control panel. Therefore, it may be used in panel retrofit applications, subject to approval by your AHJ.

FireNET 4127 I & O Manual v1.90 UL

5.9 FRCME-P Mini Input Module (w/ Pigtails)

The FRCME-P input module is used to connect standard normally open dry contact types of fire alarm devices such as manual pull stations to the FireNET 4127 SLC loop.

The FRCME-P must be programmed with a unique address from 1-127. All of the dry contact type devices connected to a single FRCME-P appear at the main control panel as a single address. Please refer to section 5.4 of this manual for instructions on programming an address into the FRCME-P input module.

Connect the FRCME-P to the FireNET as shown in figure 5.9.1. Refer to the installation instructions included with the FRCME-P for more detailed installation and wiring instructions.

UL Listed EOLR

(10K OHM)

Part # 0400-01046

White

To next SLC Device

Black

Red

IN-B

IN-A

SC (IN)

SC (OUT)

S (IN)

S (OUT)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT

LOOP 1 LOOP 2 LOOP 3 LOOP 4

MAIN CONTROL UNIT

Figure 5.9.1 FRCME-P Mini Input Module (w/ Pigtails) Detail

NOTE: The FRCME-P is approved to UL 864 8 th

edition. However, the FRCME-P will operate with the 9 th

edition approved FireNET Fire Alarm Control panel. Therefore, it may be used in panel retrofit applications, subject to approval by your AHJ.

FireNET 4127 I & O Manual v1.90 UL

5.10 FRCME-M Mini Input Module (w/ Terminal Blocks)

The FRCME-M input module is used to connect standard normally open dry contact types of fire alarm devices such as manual pull stations to the FireNET 4127 SLC loop.

The FRCME-M must be programmed with a unique address from 1-127. All of the dry contact type devices connected to a single FRCME-S appear at the main control panel as a single address. Please refer to section 5.4 of this manual for instructions on programming an address into the FRCME-M input module.

Connect the FRCME-M to the FireNET as shown in figure 5.10.1. Refer to the installation instructions included with the FRCME-M for more detailed installation and wiring instructions.

Figure 5.10.1 FRCME-M Mini Input Module (w/ Terminal Blocks) Detail

FireNET 4127 I & O Manual v1.90 UL

5.11 FRCMA / FRCMA-I Input Module

The FRCMA / FRCMA-I input module is used to connect standard normally open dry contact types of fire alarm devices such as manual pull stations to the FireNET SLC loop. The FRCMA module provides one class A or one class B input circuit. The

FRCMA-I includes built-in short circuit isolation for the SLC loop.

The FRCMA must be programmed with a unique address from 1-127. All of the dry contact type devices connected to a single FRCMA are displayed at the main control panel as a single address. Please refer to section 5.4 of this manual for instructions on programming an address into the FRCMA input module.

Connect the FRCMA to the FireNET as shown in figure 5.11.1. Refer to the installation instructions included with the FRCMA for more detailed installation and wiring instructions.

To next SLC Device

OUT SC -

OUT S +

IN SC -

IN S +

DCP-FRCMA-I

IN +

IN -

OUT +

OUT -

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT

LOOP 1 LOOP 2 LOOP 3 LOOP 4

MAIN CONTROL UNIT

Figure 5.11.1 FRCMA-I Input Module Class A Detail

FireNET 4127 I & O Manual v1.90 UL

NOTE: For Sections 5.7 – 5.10 common for all FRCM devices

Reference the input wiring distance limitation table below for all types of

FRCM modules:

Maximum Distance Between

Module and EOL Device

14 AWG 1500 Ft.

16 AWG 900 Ft.

18 AWG 550 Ft.

FireNET 4127 I & O Manual v1.90 UL

5.12 R2M Dual Relay Module Wiring

The R2M provides two separately programmable relay outputs on the FireNET 4127

SLC loop. These outputs may be used for a variety of purposes including door holders, elevator recall, and other fire safety functions.

The programmable relay contacts are rated as follows

• R2M - 1.0A @ 30VDC or 0.5A @ 125VAC, 0.35 Power Factor (PF)

• R2ML/R2ML-I – 2.0A @ 30VDC, 1PF or 0.5A @ 120VAC, 0.6PF

• R2MH/R2MH-I – 8.0A @ 30VDC or 8.0A at 250VAC Resistive, 1.0PF or 4.8A @

250VAC, 0.6PF.

The R2ML-I and R2MH-I modules have built-in Short Circuit Isolation (SCI) for the SLC loop.

Connect the R2M as shown in Figure 5.12.1. Refer to the installation instructions included with the R2M for more detailed wiring and installation instructions.

To next

SLC Device +

SC -

S +

R2M

NO1

COM1

NC1

NO2

COM2

NC2

Set 1

Form C Contacts Non-supervised

Set 2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT

LOOP 1 LOOP 2 LOOP 3 LOOP 4

MAIN CONTROL UNIT

Figure 5.12.1 R2M Dual Relay Module Wiring Detail

FireNET 4127 I & O Manual v1.90 UL

5.13 SOM Supervised Output Module

The SOM provides a supervised 24VDC polarity reversing output on the SLC loop most commonly used for audible and visual signaling appliances or triggering a remote notification appliance circuit power expander.

In addition to the SLC circuit the SOM requires a 24 VDC auxiliary input voltage. This voltage may be connected to the FN-4127 control panel terminals 18 and 19 (500ma max) or to any other UL listed fire alarm power supply providing 24 VDC.

The supervised voltage output of the SOM is rated at 2.0A maximum.

Connect the SOM to the FN-4127 control panel as shown in Figure 5.13.1. Refer to the installation instructions included with the SOM for more detailed wiring and installation instructions. Take care to install wiring so that faults on installation conductors do not affect more than one notification zone. The DCP-SOM is suitable for use only with nonsynchronized audible devices.

To next

SLC Device +

SC -

S +

SOM

24+

GND

OUT (+)

OUT (-)

Power supply voltage to next device

24 VDC UL listed, regulated, power limited supply for fire alarm signaling service, or terminals 18 and 19 on the X2 Side Terminal

Strip of the

FN-4127 (500 mA).

Compatible UL listed signaling device(s)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT

LOOP 1 LOOP 2 LOOP 3 LOOP 4

UL Listed EOLR

Part # 0400-01046

10K Ohm

MAIN CONTROL UNIT

Figure 5.13.1 SOM Supervised Output Module Detail

FireNET 4127 I & O Manual v1.90 UL

5.14 SOM-A / SOM-AI Supervised Class A Output Module

The SOM-A / SOM-AI provides a supervised 24VDC polarity reversing Class A output on the SLC loop. This module is most commonly used for audible and visual signaling appliances or for triggering a remote notification appliance circuit power expander. The

SOM-AI includes built-in short circuit isolation (SCI).

In addition to the SLC circuit the SOM-A / SOM-AI requires a 24 VDC auxiliary input voltage. This voltage may be connected to the FN-4127 control panel terminals 18 and

19 (500ma max) or to any other UL listed fire alarm power supply providing 24 VDC.

The supervised voltage output of the SOM-A / SOM-AI is rated at 2.0A maximum.

Connect the SOM-AI to the FN-4127 control panel as shown in Figure 5.14.1. Note that the SLC connections for the SOM-A are like the SOM; there is only one S+ and one

SC- terminal. Refer to the installation instructions included with the SOM-A / SOM-AI for more detailed wiring and installation instructions. Take care to install wiring so that faults on installation conductors do not affect more than one notification zone. The

SOM-A / SOM-AI is suitable for use only with non-synchronized audible devices.

Figure 5.14.1 SOM-AI Supervised Output Module Detail

FireNET 4127 I & O Manual v1.90 UL

5.15 SOM-R Supervised Output Module (Preaction Sprinkler Systems)

The SOM-R provides a supervised 24VDC output on the SLC loop for use with solenoids used in a single interlock, preaction sprinkler system.

The SOM-R consists of an output module, a polarized end-of-line device, and a keyswitch module that is used to disable the output of the SOM-R.

The SOM-R requires connections to the SLC and a 24 VDC auxiliary input voltage. The keyswitch disable module must be connected to the SLC and to the output of the SOM-

R module.

The supervised voltage output of the SOM-R is rated at 2.0A maximum.

The alarm time for the SOM-R battery calculation shall be 5 minutes in the “active status”.

NOTE: These installation instructions must be followed completely in order to comply with agency requirements! Failure to follow these installation instructions may result in improper operation of the SOM-R.

1. Determine the mounting location for the SOM-R, FRCME and SOM-R-DS keyswitch.

These should be installed in the same location, or as required by your AHJ.

2. The SOM-R must be addressed using the TCH-B100 programmer. Connect the

SOM-R to the FN-4127 SLC as shown in Figure 5.15.1. Refer to the installation instructions (Part # 1700-11320, Rev. 05/10) included with the SOM-R for additional wiring and installation instructions.

3. Connect 24VDC power to the SOM-R module. This voltage may be provided by; 1) a UL 1481 listed, regulated, power limited supply, 2) a FN-4127 NAC circuit configured as continuous auxiliary power, or 3) the FN-4127 aux power on X2 terminals 18 and 19

(500ma max).

4. The SOM-R-DS keyswitch connected to the FRCME module must be connected to the FireNET SLC. Use the TCH-B100 programmer to assign an address to the module and then connect the SLC circuit to the S+ and SC- terminals on the module.

FireNET 4127 I & O Manual v1.90 UL

5. Connect the output of the SOM-R to the input terminals on the SOM-R-DS keyswitch connected to the FRCME module. Ensure correct polarity.

Figure 5.15.1 SOM-R Supervised Output Module Detail

6. Connect the output terminals on the keyswitch disable module to the solenoid.

Ensure that the EOLD is properly connected to the circuit as shown in Figure 5.15.1 above.

Operation of the SOM-R

The SOM-R is designed for use with single interlock preaction sprinkler systems. When the FireNET control panel detects a fire alarm condition from a single initiating point, the SOM-R will be activated, allowing water to flow into the sprinkler piping. Water is not discharged from a sprinkler head until increased temperature from the fire activates the sprinkler head.

Output delays are not applied to the activation of the SOM-R. The SOM-R output is activated immediately upon detection of a fire condition by the FireNET control panel.

FireNET 4127 I & O Manual v1.90 UL

Important! For proper operation, program the SOM-R Output Attributes as follows:

o Gen Alarm Mode = YES o Silenceable = NO o Emergency = NO o Pre Alarm = NO o Trouble = NO o Pattern = CONTINUOUS o Edit Location Text = SOMR

Program the FRCME attributes as follows:

o Set Input Type = GEN PURPOSE N/C EOL o Set Input Action = SUPERVISORY o Set Input Latch = NO o Set Input Delay = 0s o Edit Location Text = SOMR IS DISABLED

Other settings may be assigned as needed.

Failure to follow these programming instructions may result in incorrect operation of the SOM-R module!

NOTE: The location text will need to be programmed to state “SOMR PREACTION

DISCHARGE” for all initiating devices, which activates the SOM-R module.

Alarm Verification may not be used with the SOM-R.

NOTE: Only one solenoid may be connected to the SOM-R. DO NOT CONNECT

MUTLIPLE SOLENOIDS TO THE SOM-R OUTPUT CIRCUIT!

To Disable the SOM-R:

Move the keyswitch to the “SOM-R Disabled” position.

To Enable the SOM-R:

Return the keyswitch to the “SOM-R Enabled” position.

NOTE: DO NOT DISABLE THE SOM-R OR KEYSWITCH

MODULE BY USING THE DISABLEMENTS MENU ON THE

FIRENET CONTROL PANEL!

ENABLE

Solenoid Compatibility List

Manufacturer Model Standby Current (Amps)

ASCO 8210G207

Parker/Skinner 73218BN4UNLVNOC111C2

0mA

Alarm Current

44mA

42mA

FireNET 4127 I & O Manual v1.90 UL

Maintenance: A maintenance agreement should be arranged through the local manufacturer’s representative and maintenance should be performed annually by authorized personnel only. To keep a preaction system in excellent working order, ongoing maintenance is required per the manufacturer’s recommendations and UL and

NFPA standards. At a minimum the requirements of Chapter 13 of NFPA 25 (2010) shall be followed.

Test Weekly: The preaction system should be tested weekly to make sure SOM-R,

FRCME and SOM-R-DS (Bypass Keyswitch) are working properly. The most common cause of an alarm system not functioning when a fire occurs is inadequate maintenance.

FireNET 4127 I & O Manual v1.90 UL

5.15 CZM Conventional Zone Module

The Conventional Zone Module (CZM) connects to the Signal Line Circuit (SLC). The module allows the analog panel to interface and monitor conventional devices such as pull stations and two-wire smoke detectors. The CZM is typically used in retrofit situations where pre-existing conventional zones are removed from a conventional system and then connected to the analog panel for discrete monitoring of that zone. All conventional devices connected to a single CZM are reported as a single input. Status conditions are reported as normal, open or alarm. It supervises the external power supply as well as the entire zone of devices. Refer to the installation instructions included with the CZM for more detailed wiring and installation instructions.

FireNET Control

Panel

FireNET

Control Panel

Figure 5.15.1 CZM Conventional Zone Module

FireNET 4127 I & O Manual v1.90 UL

5.16 DIMM Dual Input Monitor Module

The Hochiki DIMM Dual Input Monitor Modules were designed to work with pull stations, water flow switches, and other applications requiring the monitoring of dry contact alarm initiating devices. The DIMM can monitor two independent inputs with discrete reporting, yet the module only requires a single address on the SLC Loop. A typical example would be for use with a waterflow and tamper application. One input would be connected to the waterflow switch for a fire alarm condition. The second input would be connected to the tamper switch for a supervisory condition. A single DIMM module would be used instead of two single input modules such as the FRCME. The

DIMM inputs operate in a similar fashion to the FRCME input. Refer to the installation instructions included with the DIMM for more detailed wiring and installation instructions.

22k

FireNET

Control

Panel

FireNET 4127 I & O Manual v1.90 UL

5.17 SCI Short Circuit Isolator Module

The SCI short circuit isolator module is designed to help maintain partial SLC loop operation in the event that the SLC loop becomes shorted, positive to negative. In the event of an SLC loop short circuit the SLC loop is typically inoperative. By installing SCI modules throughout the SLC loop only a portion of the loop will be inoperative in the case of an SLC short circuit. When SCI modules are installed adjacent to every device for true Style 7 (see Section 5.17.1), no devices are lost from a single short on the SLC loop.

Connect the SCI module to the FireNET 4127 control panel as shown in Figure 5.17.1.

Refer to the installation instructions included with each SCI for more detailed wiring and installation instructions.

To FN-4127 control panel SLC loop -or- previous SLC loop device

+ -

(IN) S

(IN) SC

(OUT) S

(OUT) SC

To next SLC loop device or return back to FireNET 4127 control panel

Figure 5.17.1

FireNET 4127 I & O Manual v1.90 UL

5.17.1 Class A Operation

The SCI should be located within 5 feet of the FN-4127 control panel on both the outgoing and incoming SLC loop legs. In addition an SCI should be located between every SLC loop detector and module as shown in figure 5.17.2 and is required for

NFPA 72 Class A Style 7 compliance. For Class A Style 6 compliance the SCI modules may be located at strategic locations based on the installer’s or system designer’s discretion.

In the event of a short circuit on the SLC loop the 2 adjacent SCI modules to the short

(closest SCI on the left and the right of the short) will activate and its LED will turn on.

All the devices between the two SCI modules will be isolated and inoperative. All other devices on that SLC loop will remain operational. The FN-4127 control panel will indicate a trouble condition. When installing SCI modules for true Style 7 compliance, the SCI modules must be installed in a “closed nipple” fashion (see Figure 5.17.2). By using this method, no devices are lost from a single short on the SLC Loop.

Class A Style 7 SLC loop with SCI Short

Circuit Isolator Modules

SCI

First and last SCI modules must be located with 5 feet of the FN-4127 control panel.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT IN

OUT

LOOP 1 LOOP 2

OUT

LOOP 3

OUT

LOOP 4

SCI

NOTE: For NFPA 72 Style 7 compliance, SCI Modules and protected detectors or modules must be installed in “closed-nipple” fashion.

This can be accomplished by either installing two (2) SCI modules and one (1) protected detector or module in a single enclosure or raceway, or by nippling all three devices together using three separate backboxes nippled together creating an enclosed raceway.

MAIN CONTROL UNIT

Figure 5.17.2

FireNET 4127 I & O Manual v1.90 UL

5.17.2 Class B Operation

The SCI modules may be strategically located based on the installer or designer’s discretion. Typically they are located at the beginning of each branch of the SLC loop as indicated in figure 5.17.3.

In the event of a short circuit on the SLC loop, the closest SCI to the short circuit will activate and it’s LED will turn on. All devices following the SCI module will be isolated and inoperative. All devices preceding the SCI module will remain operational.

Figure 5.17.3

FireNET 4127 I & O Manual v1.90 UL

5.18 ASB Analog Sounder Base

The Analog Sounder Base (ASB) connects to the SLC Loop and requires 24VDC aux power to operate. The ASB contains an addressable sounder that is controlled by the control panel. The ASB derives its address from the Host detector (ALK, ALG, AIE, or

ATG) upon power up. The address is the detector address + 127. See section 5.4 for additional details. The addressable sounder is independently controlled by the control panel, and does not have to follow the detector status to activate.

Refer to the installation instructions included with the ASB for more detailed installation and wiring instructions.

FireNET 4127 I & O Manual v1.90 UL

5.19 AMS Addressable Manual Pull-Station

The AMS Addressable Manual Pull-Station is an integrated device that includes an input module and a manual pull-station in a single package.

The AMS is designed to be directly connected to the FN-4127 control panel SLC loop.

The AMS must be programmed with a unique address between 1 – 127. Each AMS will report individually to the panel based on its unique address. Please refer to Section 5.4 of this manual for instructions on programming an address into the AMS device.

Connect the AMS to the FireNET control panel as shown in Figure 5.19.1. Refer to the installation instructions included with the AMS device for more detailed installation and wiring instructions.

OUT TO

MODULE

SC-

S+

Hochiki America Corporation

DCP-AMS

Addressable Manual Pull Station

S+

SC-

SC S+

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9

OUT

LOOP 1 LOOP 2

LOOP 3

OUT

LOOP 4

MAIN CONTROL UNIT

Figure 5.19.1 AMS Addressable Manual Pull Station Wiring Detail

FireNET 4127 I & O Manual v1.90 UL

Section 6 - Network Connections

6.1 Compatible Network Devices

The following Hochiki America Corp. FireNET network devices are listed as compatible with the FireNET 4127 analog addressable fire alarm system.

Network Interface Card

• FN-4127-NIC

Network Devices

• FN-LCD-N Network LCD Annunciator

This section covers the installation of the devices listed above. For proper operation each of these devices must be programmed using the Loop Explorer software. Please refer to Section 9 of this manual for more information on programming the functionality of network devices.

The FireNET system enables information to be transmitted between control panels using a secure network connection. Up to sixty-four control panels and network annunciators (nodes) can be connected together and the system can be configured such that selected information can be displayed or acted upon at each panel.

FireNET 4127 I & O Manual v1.90 UL

6.1.1 FN-4127-NIC Network Interface Card

To enable control panels to be connected together as a network, a network card must be installed in each panel. This card connects to the FN-4127 on

Front Panel PCB the rear of the panel door and is held in position by two M3 screws. The network card is installed in the exact same fashion for the FN-LCD-N Network LCD annunciator.

To install a network card, the AC and battery power

M3 Screws must first be switched off and the metal cover over the front panel PCB removed. The network card can then be plugged into the two connectors (J1 and J3) in the bottom right of the main panel PCB and secured in position with the M3 screws.

OBSERVE STATIC PRECAUTIONS WHEN HANDLING CIRCUIT BOARDS

Each network node must

This switch setting shows address number one.

Switch position up selects the binary digit, so a switch with

1,2 and 3 up would represent address number 7.

be allocated a unique network address. This is

1 2 3 4 5 6 7 8

(The black part shows the switch actuator) done by setting the DIP switches on the network card to the required binary

C19

R11

OP5

R4 R8 C4

RL2

R16

+ +

Processor reset switch number as shown above.

It is important that each panel has a different

OP6

R12 R10 R7

TR4 TR3 TR6

RL1

C14

R21

R15

R20

R19 address for correct operation so care must be taken to set and record

C13

SW2

R17

TR5

RP1 the network card address for each panel. Always set

C11

C20

R26

C12

C16

U5 the address on the DIP switches with power to the

R25

R28

R24 panel switched off.

This switch setting shows

K6005

R27

C15

LED1 R13

LED2 R14

C10

C17 C18

+ address number one.

Switch position up selects

LED1-GREEN = OUTGOING CONNECTION OK LED2-RED = INCOMING CONNECTION OK the binary digit, so a switch with 1,2 and 3 up would represent address number 7.

The network card has a green and a red LED indicator to show the status of the incoming and outgoing communications. Under normal circumstances, both LEDs will be lit, indicating that the card is communicating properly. If one or both of the LEDs are not lit then the connection to neighboring panels is not functioning properly.

FireNET 4127 I & O Manual v1.90 UL

6.1.1.1 Cable Length

The FireNET network communications protocol has been designed to be extremely tolerant to interference and data corruption, however as with any system, limitations must be set to guarantee correct operation. The specified transmission distance limit for the communications method used is 4000 ft. (1200m) and because the data is retransmitted at each network card, in theory, there can be 4000 ft. (1200m) between each card if required. The minimum cable size for the FireNET network is #20 AWG.

The network communications uses RS485 technology.

Using the above cable distances however, does not take into account the failure of a network card to communicate with the system through total power failure or a card trouble. In this situation, the network card would disconnect itself from the network and connect the network cable such that it bypasses the card in question. This means that the total cable length between the cards either side of the disconnected one could be

8000 ft. (2400m), which is outside of the specification for the communications method used (RS485). This trouble scenario could clearly be extended to more network cards and this would add 4000 ft. (1200m) of cable length in each case.

A sensible trouble tolerance limit must therefore be suggested to enable the performance of the system to be predicted. Because of the nature of the fire protection system, its design is biased towards inherent reliability and failure of a network card, although possible, is very unlikely. Fire control panels also have substantial back up power systems, therefore, the likelihood of a total power failure under operational conditions, is also extremely rare. A suggested tolerance level of one card failure is therefore recommended. To guarantee operation of the system with one card failure it is necessary to arrange the network so that a failure will not introduce more than 4000 ft. (1200m) of cable between the two cards, which would be connected together by the failure. This means that the total cable length between adjacent nodes should not be more than 4000 ft. (1200m). It is not important how the 4000 ft. (1200 meters) is made up i.e. it could be 350 ft. (100m) and 3650 ft. (1100m) or 2000ft. (600m) and 2000ft.

(600m).

Using these general rules and the specified or equivalent cable types will provide a guaranteed performance of networks with plenty of tolerance.

FireNET 4127 I & O Manual v1.90 UL

6.1.1.2 Wiring Scheme

Network

Panel 1

2 LOOP

Network

Panel 2

2 LOOP

4000 ft. Max.

Network

Panel 3

4 LOOP

Network

Panel 4

4 LOOP

Network

LCD

Annunciator

When designing or installing a network of FireNET panels and annunciators, always be aware of the following:

1. The panel network must be wired as a ring (Class A).

2. There should be no more than 4000 ft. (1200m) maximum cable length between two adjacent segments.

3. A short circuit at Point A should automatically disconnect the shorted section and announce a trouble condition at all panels but the entire network will continue communicating.

4. A short circuit at Points A and B should automatically disconnect both sections and announce trouble at all panels. Communication will continue between panels1 and 4 and between panels 2 and 3.

5. Open circuit troubles should allow the network to continue operating in the same way as short circuit troubles.

6. Network cabling should be standard RS485 type for up to 64 nodes.

7. The minimum cable size for the FireNET network is #20 AWG.

FireNET 4127 I & O Manual v1.90 UL

6.1.1.3 Cable Type

The cable type used for the network connection should be suitable for RS-485 applications. Minimum wire size should be 20ga. twisted, shielded, stranded. RS485 communications cable is typically standard Class 2 communications cable. However, depending on the AHJ, FPL or FPLR cable may be required. Follow local jurisdictional and AHJ requirements. NFPA 70 national electric code compliance may be required for network cabling depending on local jurisdiction, AHJ, regulations, and/or codes.

6.1.1.4 Proper Shield Termination of the Network Cable

In many installations, interference from RFI, EMI or other noise sources can create problems. In order to reduce the effects of such noise, terminate the shield to the earth ground terminal block in the main control panel. DO NOT ground the shield at both ends of the cable!

FireNET 4127 I & O Manual v1.90 UL

6.1.1.5 C onnecting

two cables connected anels. If eit ther of thes e

. next panel and so on.

. the cable s hould not e F (55 C).

NOTE: It i is importan t to ensure onnection fr rom the OU nel connect ts to the IN- of t the next pa nel and so on.

X1 Terminal Stri ip

- + - +

OUT I N

LOOP 1

- + - +

OUT IN

LOOP 2

- +

OUT

- +

LOOP 3

- +

OUT

- +

LOOP 4

NC C NO

FIRE 1

NC C NO

TROUBLE

WARNING!

NC C NO

FIRE 2

NC C NO NC C NO

SUPERVISORY

AUXILIARY

+ - + - + - + -

NAC 1 NAC 2 NAC 3 NAC 4

FIRE

ROUTING

TROUBLE

ROUTING

PROGRAMMABLE

OUTPUT

1. TBL

DO NOT PLUG ERED. STATIC SENSITIVE CIRCUITS.

OBSERVE STATIC HANDLING PROCEDURES A

REMOTE

CONTROL

AND AUX.

INPUTS

2. RES

3. INT

4. CNT

5. SIL

6. PR1

7. PR2

8. PR3

COMMS

ADDITIONAL

I/O BOARDS

AUX

24V

NETWORK

OUT

REMOTE PSU

Network cable from “OUT” terminals of previous panel/ annunciator

- - + +

Network cable to

“IN” terminals of next panel/ annuciator

Manual

6.1.2 FN-LCD-N Network Liquid Crystal Display Annunciator

The FN-LCD-N Network Annunciator duplicates the indications of the FN-4127 fire alarm control panels connected to the same network. The FN-LCD-N connects to the control panel via the network interface and requires that the main control panel have an

FN-4127-NIC network card fitted.

The FN-LCD-N Network Annunciator is connected to the network and any number of panels can be connected up to the maximum number of nodes allowed by the network specification, which is 64 (including control panels).

Specific network attributes and routing information from any or all control panels may be assigned to the FN-LCD-N. The LCD display and user interface on the FN-LCD-N operate and indicate in the same manner as the control panel.

The FN-LCD-N is considered a network “node” to the FireNET network just like the control panels.

For operations and programming refer to Sections 7, 8 and 9 of this manual.

Figure 6.1 FN-LCD-N Network LCD Annunciator

When powering the FN-LCD-N from the FireNET Aux 24VDC power (limited to 500ma), the following maximum wiring distances apply at the gauges noted:

Wire Distance

18AWG 925ft

16AWG 1500ft

14AWG 2400ft

FireNET 4127 I & O Manual v1.90 UL

Figure 6.2 FN-LCD-N Wiring

NOTE:

When connecting I/O boards to the FN-LCD-N via the COMMS terminals shown above, the I/O boards must be powered by a UL864 listed local Auxiliary

24VDC power supply, or the Aux 24VDC output of the FN-LCD-N within the limits outlined below.

DO NOT connect the I/O board power input to the Aux 24VDC output terminals of the

FN-LCD-N unless the sum current load of the I/O board is within the 500ma max

24VDC output rating of the FN-LCD-N and within the 500ma max 24VDC output rating of the FN-4127 control panel that provides power to the FN-LCD-N. Failure to make this consideration may result in overloading the FN-LCD-N and/or the control panel

Aux 24VDC output (500ma max. each).

The current limits during both standby and in alarm shall not exceed the 500 mA rating.

Available Colors: RED and CHARCOAL, FN-LCD-N-R = RED, FN-LCD-N-C =

CHARCOAL

FireNET 4127 I & O Manual v1.90 UL

Section 7 - Basic Front Panel Operations and Programming

(Access Level 1, 2, and Real-Time Operation)

This section covers the basic user operations of the FN-4127 and is intended to provide the casual user a basic understanding of how to complete common system operations.

In addition to providing an overview of the front panel controls this section also includes instructions on how to:

• Perform a Lamp Test

• Silence the Panel Sounder

• View Multiple Fire Alarms on the Panel Display

• View Multiple System Events on the Panel Display

• Use the Menu Navigation Buttons

• Use the Help Function an

• Resound an Alarm

• Reset an Alarm

• Initiate a Fire Drill

• Disable Portions of the System

• View the Status of System Devices

• Set system time

All of these operations are performed from the front panel keypad.

Please refer to the front panel photo in Figure 7.1 below while reading through this section.

Figure 7.1 Front Panel Control

FireNET 4127 I & O Manual v1.90 UL

7.1 Operating Modes

This section provides a brief overview of Access Level 1, 2, and 3 operating modes.

Access Level 1 and 2 operating modes are used in the basic system operations described in this chapter. Access Level 3 is typically used only by installation and service personnel and is explained in greater detail in Section 8 of this manual.

7.1.1 Access Level 1

When the FN-4127 control panel is in Normal Standby condition only the green AC

Power On

LED will be lit, and the date and time displayed on the LCD display. Normal

Standby

is considered to be in Access Level 1. Some very basic operations can be done in Access Level 1 by simply pushing the corresponding button(s) on the front panel controls. For information on which basic user operations can be done from

Access Level 1 see section 7.2.

Note that when using the Denver Door build the control panel buttons are not accessible until the door is opened.

7.1.2 Access Level 2

Many of the front panel controls and their operations require the user to enter a more secure operating mode called Access Level 2. This more secure operating mode prevents unauthorized individuals from operating the FN-4127 fire alarm system. For information on which basic user operations are done from Access Level 2 see section

7.3.

7.1.3 Access Level 3

A higher security mode called Access Level 3 is also available to system administrators, installers, and service personnel to make critical changes to the system.

For more information on Access Level 3 refer to Section 8 of this manual. None of the basic operations covered in this section require entry to Access Level 3 operating mode. Access Level 3 operating mode should be restricted to qualified installation and service personnel only.

7.2 Access Level 1 Operations

7.2.1 Performing a Lamp Test

Press the “Lamp Test” button on the front panel to illuminate all front panel LED indicators, LCD display, and validate correct operation. Release the button to conclude the test.

FireNET 4127 I & O Manual v1.90 UL

7.2.2 More Fire Events

The front panel display is capable of displaying the information for up to two different points that are in alarm condition. If more than two points are in an alarm condition simultaneously the front panel display above the “More Fire Events” button will indicate how many additional alarms are active. For example the display may indicate

“1 More Fire”. In this case there is one additional point in fire alarm condition that is not currently shown on the display. By pressing the “More Fire Events” button, the user can display these additional alarms.

7.2.3 More Events

Similar to the “More Fire Events” button, the “More Events” button allows the user to display more non-fire alarm events if more than 2 events are active on the system at one time.

7.2.4 Menu Navigation (Up, Down, Left, Right Arrows, Enter / Exit Buttons)

These buttons are used to navigate the FN-4127 menu structure. The arrow buttons

(up, right, down, left) also represent the digits 1, 2, 3, and 4 respectively when entering codes for Access Level 2 or Access Level 3 modes.

7.2.5 Help (?)

The “Help” button offers additional information relating to the current status of the FN-

4127 control panel and provides assistance in basic operation of the system. Press and hold the “Help” button to display this additional information.

Note: When using the Denver Door build of the FireNET panel, the front door of the panel must be opened to perform these commands.

FireNET 4127 I & O Manual v1.90 UL

7.3 Access Level 2 Operations

The following operations can only be done after the panel is placed into Access Level 2 operating mode. To place the FN-4127 into Access Level 2 follow these instructions:

7.3.1 Entering Access Level 2

1. Press any navigational arrow key to enable the panel.

2. Using the arrow keys enter the 5 digit code. Digit values are 1 - 4 only and correspond to the value on each arrow key. (Up = 1, Right = 2, Down = 3, Left =

4) The factory default for the Access Level 2 code is 22222.

3. Press the Enter key. The front panel graphic display will confirm you are in

Access Level 2.

4. If there is no activity for 120 seconds on the front panel controls once the system is in Access Level 2 operating mode, the system will time out and revert back to

Access Level 1 operating mode automatically.

5. You may also use the Enable Access keyswitch on the front door of the panel to enter Access Level 2. Simply insert the key and turn it to the right. The panel display will confirm that you are in Access Level 2.

NOTE

: The FireNET panel will NOT time out to Level 1 when using the key. Be sure to return the key to the OFF position and remove it when not in use!

When using the Denver Door build of the FireNET panel, opening the enclosure door will put the panel into access level 2 automatically.

7.3.2 Silencing an Alarm

To silence an alarm condition place the panel into Access Level 2 operating mode as described in 7.3.1. Press the “Alarm Silence” button. The “Alarm Silence” button acknowledges any current alarm conditions and typically silences any audible and visual notification appliances such as horns and strobes. In some cases the system may be programmed so that the “Alarm Silence” button silences the audible notification appliances but allows the visual notification appliances such as strobes to remain flashing. Your system installer can inform you how your system is set up to operate.

After an alarm has been silenced, the flashing fire LED’s will go steady, and “alarm silenced” will display in the upper right corner of the LCD display.

7.3.3 Resounding an Alarm

To resound an alarm condition place the panel into Access Level 2 operating mode as described in 7.3.1. Press the “Resound Alarm” button. Pressing the “Resound Alarm” button will reactivate any audible or visual notification appliances that were previously silenced using the Alarm Silence operation.

FireNET 4127 I & O Manual v1.90 UL

7.3.4 Resetting an Alarm

Once a fire or other alarm condition has been verified and cleared it is necessary to reset the panel. To reset the FN-4127; place the panel into Access Level 2 operating mode as described in 7.3.1. Press the “Reset” button. All latched outputs such as relays used for elevator recall will return to their normal state.

Prior to resetting the panel it is necessary to clear the condition that caused the alarm.

For example, if a manual pull station was activated to cause the alarm, that manual pull station must be physically reset in order to reset the panel. If you attempt to reset a panel that has an existing alarm condition that has not been cleared, the panel will go back into alarm immediately after trying to reset.

7.3.5 Initiating a Fire Drill

To initiate a fire drill place the FN-4127 panel into Access Level 2 operating mode as described in 7.3.1. Press the “Fire Drill” button to engage fire drill mode. The fire drill activates NAC and SOM indication circuits, but does not activate fire relays, R2M, programmable relays, etc. A subsequent press of the fire drill button will deactivate fire drill mode. Any actual fire alarms during a Fire Drill will automatically override fire drill mode.

7.3.6 Silence the Panel Sounder

Many system conditions such as system troubles will activate the sounder in the FN-

4127 main control panel. The user can silence the panel sounder by pressing the

“Panel Sounder Silence” button on the front panel. This silences only the panel sounder. Other audible outputs such as horns or strobes require a different operation to silence.

FireNET 4127 I & O Manual v1.90 UL

7.4 Advanced Access Level 2 Operations

7.4.1 Access Level 2 Main Menu

Once you have entered Access Level 2 operating mode you can view the Access Level

2 Main Menu, which gives the user the ability to perform additional system operational functions. To view the menu, enter Access Level 2, and then press any one of the navigational arrow keys.

ACCESS LEVEL 2 MAIN MENU

DISABLEMENTS

VIEW DEVICES

TEST ZONES

SET SYSTEM TIME

SENSOR MAINTENANCE EARLY

WARNING

ACCESS LEVEL 3

Table 7.4 Main menu items at Access Level 2

Once this menu is displayed you can scroll up or down using the navigational arrow keys to highlight each of the six menu options. A menu option is highlighted when a triangular arrow symbol appears to its left.

Each menu option may be selected by first highlighting it using the up/down arrow keys, then pressing the right arrow key to select. The six Access Level 2 Main Menu option functions are described in the following sections.

7.4.2 Disablements

The Disablements menu allows the user to disable individual points, circuits, zones, or loops on the FN-4127 fire alarm system. This is typically done while the system is being serviced or tested or to temporarily remove a faulty system device. CAUTION: Any portion of the system that is disabled will not report an alarm condition.

All disablements have two options, timed or untimed. For disablements up to 24 hours in length the timed disablement option should be used. This will prompt the user to enter a disablement time in 30-minute increments from 30 minutes to 24 hours. Once the disablement begins the FN-4127 will countdown the selected disablement time.

When the time expires the disablement is cancelled automatically.

Untimed disablements should be used only when it is necessary to disable a portion of the system for over 24 hours. Untimed disablements remain active until they are manually reset at the panel through the Access Level 2 Main Menu / Disablements command.

FireNET 4127 I & O Manual v1.90 UL

Once you select timed or untimed disablement you can choose to disable loops, zones, addresses, NAC, or I/O circuits through sub-menus to the Access Level 2 Main Menu /

Disablements option.

As previously discussed highlighting the desired menu option and then pressing the right navigational arrow selects that option. Pressing the left navigational arrow at any time backs out of the current menu returning to the previous menu.

Note:

The FN-4127 fire alarm system will indicate a disabled condition any time there is an active disablement on the system, via LCD display text and the “point bypassed”

LED on the front panel. Any item disabled is considered an off-normal condition and will generate a common trouble condition until the disabled item is returned to normal.

7.4.2.1 Disabling Loops

The Disable Loops sub-menu option to Disablements, allows you to disable an entire

SLC loop with one command. The SLC loop may contain up to 127 analog detectors and addressable input and/or output modules, as well as up to 127 analog sounder bases. Disabling an entire SLC loop disables all inputs and outputs on the loop and should be used only in extreme cases such as a service related problem affecting all the devices on the SLC loop.

WARNING:

Loop disablement does not electrically isolate the panel from the SLC loop wiring. The SLC loop should be disconnected from the panel before any diagnostic testing is performed.

Disabling Zones

Each device on the system is assigned to a zone by the system installer. Refer to the installation records in Section 11 of this manual for a list of all points on the system and the zones they are assigned to. A zone may consist of one or many points. Disabling a zone disables all the points assigned to that zone.

Disabling Addresses

Each SLC loop device on the system is assigned a unique address. In some cases an

SLC loop device may have sub addresses as well. Using the Disable Address submenu command the user can individually disable any single address on the system.

FireNET 4127 I & O Manual v1.90 UL

Disabling NAC Outputs

The disable Audible Device output sub-menu option allows the user to disable all of the local NAC, SOM, and ASB outputs on the system. This is typically done for periodic tests so the building occupants are not disturbed while activating each alarm device.

When you choose this option all of the notification appliances connected to the panel notification appliance circuits and SOM are disabled, as well as any analog sounder bases.

Disable Panel I/O

The Disable Panel I/O sub-menu option allows a user to disable an individual panel input or output. This includes individual notification appliance (NAC) circuits, on-board panel relays, and the on-board digital inputs. This option applies only to on-board inputs and outputs – SLC loop devices must be disabled by using the Disable

Addresses option.

View / Restore Disablements

The View/Restore Disablements sub-menu option is used to quickly display any system disablements and optionally reset them to normal. Scroll to the View/Restore

Disablements sub-menu option, press the right navigational arrow to select, and then follow the prompts on the panel display to view/reset any disablements on the system.

7.4.3 View Devices

The View Devices menu option allows the user to view every SLC loop device. For each device the panel display will indicate the device type, zone, and location text. In addition, analog devices such as smoke and heat detectors will also be displayed with their current analog value. This analog value can be useful in determining if a smoke detector requires cleaning. Photoelectric detectors also display in terms of obscuration

(%/ft) and the heat detectors in terms of temperature (F°).

For non-analog input devices the current status will be displayed as Off or On. For nonanalog output devices the current status will be displayed as either Off or Activated.

Service personnel who want to verify system devices and troubleshoot potential problems typically use the View Devices sub-menu option.

7.4.4 Test Zones

The Test Zones sub-menu option is used by service personnel to quickly and easily perform periodic system tests. Please refer to Section 10 of this manual for a more detailed explanation. This feature is typically referred to as a “One Man Walk Test.”

FireNET 4127 I & O Manual v1.90 UL

7.4.5 Set System Time

This sub-menu option is used to adjust the FN-4127 internal clock. It is important to make sure the clock is accurate so that events logged in the event log are recorded with the correct time.

To set the system clock, select the Set System Time sub-menu option by highlighting it with the up/down arrow keys. Select it by pressing the right arrow key. The resulting menu allows you to individually set the Year, Month, Day, Hour, Minute, and Daylight

Savings. Highlight each option by using the up/down arrow keys. Press the right arrow key to select it. Use the up/down arrow keys to change the current values. Pressing the left arrow key in any menu backs you out to the previous menu.

7.4.6 Sensor Maintenance Early Warning

This option is used by service personnel to identify sensors that require cleaning or replacement.

7.5 Panel Operation

This section summarizes the operations described earlier in this section of the manual for handling Fire, Trouble, and Supervisory conditions.

7.5.1 Fire Condition

In the event a device on the FN-4127 fire alarm system activates in a fire alarm condition the following will happen:

• Both FIRE LED indicators on the front panel will turn on and flash.

• Details of the device that caused the fire alarm condition will be given in the LCD status display on the front panel.

• If there are more than two fire conditions, press the “More Fire Events” button on the front panel to view the additional fire alarms.

• Audible and visual notification appliances (horn and strobes) will activate throughout the building.

• Output relays and circuits will operate performing fire alarm functions such as closing doors, recalling elevators, shutting down air handling equipment etc.

• The panel buzzer will be pulsing.

FireNET 4127 I & O Manual v1.90 UL

The operator actions required following a fire alarm condition are as follows:

• Silence the panel buzzer by pressing the “Panel Sounder Silence” button.

• Silence the notification appliances by entering Access Level 2 and pressing the

“Alarm Silence” button. (See section 7.3.1 for instructions on entering Access

Level 2). When the Fire condition is silenced, both fire LED indicators change from flashing to steady and the LCD display will indicate “Alarm Silenced”.

• Resound the audible and visual notification appliances if necessary by entering

Access Level 2 and pressing the “Resound Alarm” button.

• Once the fire department has cleared the building, physically reset any devices such as manual pull stations that require a manual reset.

• Reset the FN-4127 fire alarm control panel by entering Access Level 2 and pressing the “Reset” button.

7.5.2 Trouble Condition

Trouble conditions occur when problems with the FN-4127 fire alarm system components and wiring are detected.

When the FN-4127 fire alarm control panel senses a trouble condition, the following will occur.

• The General Trouble LED will illuminate on the front panel.

• Other trouble LED’s indicating the nature of the trouble may also illuminate.

• The trouble relay contact and voltage output in the control panel will activate

• Details of the trouble condition will be shown on the LCD status display on the front panel.

• If there are two or more trouble events press the “More Events” button to view them in the LCD status display on the front panel. (See section 7.3.1 for instructions on entering Access Level 2).

• The panel buzzer will sound.

The operations required following a trouble condition are as follows:

• Press the “Panel Sounder Silence” button to silence the panel buzzer. (See section 7.3.1 for instructions on entering Access Level 2).

100

FireNET 4127 I & O Manual v1.90 UL

• Note the LCD status display and any messages that may appear so these can be relayed to service personnel.

• Investigate the cause of the trouble. It may be as simple as a detector that was inadvertently removed.

• If the trouble condition cannot be resolved, contact your service company.

There is no need to reset trouble conditions. They are non-latching and reset themselves after the trouble condition is corrected.

NOTE

: Loop Open/Short troubles are latching and require a panel reset to clear.

7.5.3 Supervisory Condition

A supervisory condition is detected when a portion of a building system that controls the spread of fire or smoke is disabled. This is most commonly a fire sprinkler valve that is turned off for maintenance purposes.

When the FN-4127 fire alarm control panel senses a supervisory condition the following will occur:

• The Supervisory Alarm LED will illuminate on the front panel.

• The supervisory relay contact in the control panel will activate.

• Details of the supervisory condition will be shown on the LCD status display on the front panel.

• The panel buzzer will sound.

The operations required following a supervisory condition are as follows:

• Press the “Panel Sounder Silence” button to silence the panel buzzer. (See section 7.3.1 for instructions on entering Access Level 2).

• Note the LCD status display and any messages that may appear so these can be relayed to service personnel, fire department, and/or central station.

• Investigate the cause of the supervisory conditions.

• If the supervisory condition cannot be resolved, contact your service company.

• Once the supervisory condition has been cleared, reset the FN-4127 fire alarm control panel by entering Access Level 2 and pressing the “Reset” button.

101

FireNET 4127 I & O Manual v1.90 UL

7.5.4 Pre-Alarm Condition

A Pre-Alarm condition occurs when an analog sensor reaches its pre-alarm threshold, or when an input whose type is set to pre-alarm activates. This condition typically occurs as the sensor approaches its fire point.

When the FN-4127 fire alarm control panel senses a pre-alarm condition, the following will occur:

• The Pre-Alarm LED will illuminate on the front panel.

• Details of the pre-alarm condition will be shown on the LCD status display on the front panel.

• If there are two or more events, press the “More Events” button to view them in the LCD status display on the front panel.

• The panel buzzer will sound.

The operations required following a Pre-Alarm condition are as follows:

• Press the “Panel Sounder Silence” button to silence the panel buzzer. (See section 7.3.1 for instructions on entering Access Level 2).

• Note the LCD status display and any messages that may appear so these can be relayed to service personnel.

• Investigate the cause of the Pre-Alarm, such as a significant presence of smoke, heat, or an actual fire starting.

• If the Pre-Alarm condition cannot be resolved, contact your service company.

• Once the Pre-Alarm condition has been cleared, reset the FN-4127 fire alarm control panel by entering access level 2 and pressing the “reset” button.

102

FireNET 4127 I & O Manual v1.90 UL

Section 8 -

Advanced Front Panel Operations and Programming

(Access Level 3)

8.1 Access Level Overview

The FireNET 4127 has 3 modes of operation. Access Levels 1 and 2 are operational levels that allow the user to perform operational commands such as silencing an alarm or resetting the panel. Access Levels 1 and 2 are explained in further detail in Section 7

- Basic Front Panel Operation and Programming.

Access Level 3 is an installer level operating mode that allows the user to perform some of the basic programming commands used to configure the FN-4127 fire alarm system.

Some of the basic programming functions for the FireNET 4127 control panel can be done from the front panel controls. To fully program the FireNET 4127 fire alarm system however, you should use a PC running the Loop Explorer software package (See

Section 9).

This section covers the basic programming functions that can be done from the front panel controls of the FN-4127 fire alarm control panel.

8.1.1 Entering Access Level 3

In order to enter Access Level 3 operating mode you must first enter Access Level 2 operating mode. From the Access Level 2 Main Menu you can select Access Level 3.

To enter into Access Level 3 follow these steps:

1. Press any arrow key to enable the panel.

2. Using the arrow keys enter the 5 digit code for Access Level 2. You can only use digit values of 1-4. The up/down arrow keys represent the values 1-4. Up

= 1, Right = 2, Down = 3, and Left = 4. The default Access Level 2 code is

22222

3. Press the Enter key. The front panel graphic display will confirm you are in

Access Level 2.

4. Press the right arrow key to access the Access Level 2 Main Menu.

5. Press the down arrow key until Access Level 3 is highlighted with a triangular arrow to the left of it.

103

FireNET 4127 I & O Manual v1.90 UL

6. Press the right arrow key to select Access Level 3.

7. Using the arrow keys enter the 5 digit Access Level 3 code. Digit values are

1-4 only. The default Access Level 3 code is 33333.

8. Press Enter.

Note: If you back out of the Access Level 3 menu using the Exit button or the left arrow key, you will have to re-enter the code to go back into Access Level

3 operating mode.

To enter access level 2 when using the Denver Door build of the FireNET panel, it is only necessary to open the front door of the enclosure.

8.2 Access Level 3 Menu

Table 8.2 shows the menu structure of the Access Level 3 main menu. You can scroll up and down using the arrow keys to highlight each menu option. Once the option is highlighted with a triangular arrow to the left of it, you can select the option by pressing the right arrow key.

Table 8.2 Access Level 3 Menu Structure

ACCESS LEVEL 3 MENU

►EDIT CONFIGURATION

SET TIMES

VIEW PRINT EVENT LOG

PRINT CONFIGURATION

SYSTEM DISABLEMENTS

LOOP DATA TEST

8.2.1 Edit Configuration

The Edit Configuration menu option displays a sub-menu with even more options to select. Table 8.2.1 indicates these options.

Table 8.2.1 Edit Configuration Menu Structure

EDIT CONFIGURATION MENU

► EDIT SUPPLIERS NAME

EDIT GENERAL ALARM MODE

EDIT I/O

ADD/DELETE DEVICE

EDIT DEVICE ATTRIBUTES

AUTO LEARN

104

FireNET 4127 I & O Manual v1.90 UL

8.2.1.1 Edit Suppliers Name

The suppliers name is a custom message that is displayed on the front panel LCD status display in normal operation, just under the time/date information at the top of the screen.

The suppliers name can be any text message up to 40 characters long. The default suppliers name message is “Auto Configured Panel”.

From the EDIT CONFIGURATION MENU, highlight “EDIT SUPPLIERS NAME” by using the up down arrow keys then select it by pressing the right arrow key.

Using the left and right arrow keys, select the character you want to edit. Using the up and down arrow keys scroll through available characters that can be used. Refer to the on-screen instructions for additional information.

8.2.1.2 General Alarm Mode

The FN-4127 can be programmed to operate in three different ring modes.

“Common” ring mode activates all audible and visual notification appliance circuits when a fire alarm is activated. This is the default mode of the FN-4127 panel.

“Zonal” ring mode activates only the audible and visual notification appliances that are programmed into the same zone as the device causing the alarm.

Select EDIT GENERAL ALARM MODE from the EDIT CONFIGURATION MENU and use the arrow keys to scroll between “Common” and “Zonal”. Follow the on screen prompts or use the Help (?) button for additional information.

8.2.1.3 Edit I/O

The EDIT I/O menu option allows the user to set the attributes of all the FN-4127 control panel input and output circuits. Selecting EDIT I/O displays a sub-menu giving the user the choice of “Edit Panel I/O” or “Edit Remote I/O”.

8.2.1.3.1 Edit Panel I/O

Edit Panel Inputs

Selecting “Edit Panel Inputs” allows the user to scroll between the following panel input circuits. These inputs are utilized by installing a normally open switch contact between

Terminal 12, which is 0V, and each input listed below. Please refer to Section 3.6

Digital Inputs for more detail on wiring & limitations of these inputs.

• Trouble Input (Terminal 7)

105

FireNET 4127 I & O Manual v1.90 UL

• Reset Input (Terminal 8)

• Intermittent Input (Terminal 9)

• Continuous Input (Terminal 10)

• Sil. Alarm Input (Terminal 11)

• Programmable Input 1 (Terminal 13)

• Programmable Input 2 (Terminal 14)

• Programmable Input 3 (Terminal 15)

• Programmable

Each input circuit has the following properties that can be edited. Select each menu option and follow the on screen prompts or press the Help (?) button for further information.

• Zone o Selecting this option allows the user to program which software zone the

• Input input will be placed in. Default is 0.

Delay o Input delays can be programmed (where acceptable by the Authority

• Input

Having Jurisdiction) in 10-second increments up to 2 minutes.

Latch o Each input can be programmed as latching or non-latching. Latching requires the panel to be reset before the condition is cleared. Nonlatching resets the condition automatically when the input returns to

• Input normal.

Action o Input action is the type of event that occurs when the input is activated.

Choose between Trouble, Pre-Alarm, Supervisory, Auxiliary, Silence

Alarm, Reset, Transparent, Disablement, Test, or Fire.

• Edit Location Text o This option allows the user to scroll through the available characters using the arrow keys, and create a custom text message up to 40 characters describing this input.

Edit Panel Outputs

Selecting “Edit Panel Outputs” allows the user to scroll between the following panel output circuits.

Appliance

• Notification

Appliance

• Notification

Circuit 4 (Terminals 38 & 39)

• Fire1 Contact (Terminals 17-19)

• Trouble Contact (Terminals 20-22)

• Fire2 Contact (Terminals 23-25)

• Supervisory Relay (Terminals 26-28) [Not User Programmable]

• Auxiliary Relay (Terminals 29-31)

• Fire Routing Voltage Output (Terminals 1 & 2)

• Trouble Routing Voltage Output (Terminals 3 & 4)

106

FireNET 4127 I & O Manual v1.90 UL

• Programmable Voltage Output (Terminals 5 & 6)

Each output circuit has the following properties that can be edited. Select each menu option and follow the on screen prompts or press the Help (?) button for further information.

• Zone o Selecting this option allows the user to program which software zone the input will be placed in. Default is 0.

• Attributes o This option allows you to select the output attributes flags for general alarm, silenceable, output, pre-alarm output, trouble output, and Strobe

Output. (Strobe option for NAC outputs only).

• Delay Stage 1 o If you are using staged evacuation. This option sets the delay for stage 1 in 30 second increments up to 5 minutes maximum (Not Available for

NAC outputs).

• Delay Stage 2 o If you are using staged evacuation. This option sets the delay for stage 2 in 30 second increments up to 5 minutes maximum (Not Available for

NAC outputs).

• Test Device Output o This option allows the output to be manually turned on or off by the user.

• Configure o This option allows NAC Outputs to be alternately programmed as power outputs such as constant power, door holder power or resetable power.

NOTE

: Panel Outputs can be programmed into three primary categories:

• Common o When output attribute flags are set for general event categories, the output operation will follow the common activation of that event type. General Alarm mode should

Edit Default Pattern

be set to “common” for this operation.

• Zone o When outputs are assigned to zones, the output operation can be triggered on a zoned basis. General alarm mode should be set to “zonal” for this operation.

• Programmable o When outputs are not assigned to general event categories via output attributes, the output operation is programmable by using Cause and Effect.

“Edit Default Pattern” allows you to select the on-board NAC circuit output pattern. The available options are Continuous, Temporal and March. The default is Temporal.

107

FireNET 4127 I & O Manual v1.90 UL

Edit Alarm Verification

The alarm verification time value can be set between 5 and 60 seconds. This value must be to 60 seconds to be compliant with UL864 9 th

Edition. Default value is 60 seconds. (See the prefix of this manual for additional details).

Edit AC Fail Report Delay

The AC Fail report delay time value can be set between 0 and 24 hours. Default value is one (1) hour. This value must be set between 1 and 3 hours to be compliant with

UL864 9 th

Edition. (See the prefix of this manual for additional details).

8.2.1.3.2 Edit Remote I/O

I/O Board Addresses 1 – 32 can be selected within this menu. Input Channels can be edited within this menu. Programming attributes are the same as described in panel input menu. Output Channels can be edited within this menu. Programming attributes are the same as described in panel output menus. Each I/O board has 16 input/output channels. Each I/O Channel can be selected to be either an input or an output.

8.2.1.4 Add/Delete Device

Selecting the ADD/DELETE DEVICE Menu Option allows the user to add or delete a single SLC loop device to any of the 4 possible SLC loops on the system. To add an

SLC loop device using this menu option follow these instructions.

8.2.1.4.1 To Add a SLC Loop Device

1. Select ADD DEVICE from the EDIT CONFIGURATION MENU by highlighting it, then pressing the right arrow key to select.

2. A sub-menu listing each of the 4 possible SLC loops is displayed. Highlight one of the SLC loops then select it by pressing the right arrow key.

3. Using the up/down arrow keys scroll to the address value that the new SLC loop device is programmed to (1-127 for Sensors and Modules, 128 – 254 for ASB).

Only open address values will be displayed which helps to eliminate duplicate address problems. Press the right arrow key to select.

4. Scroll through the list of possible SLC loop devices by using the up/down arrow keys. Press the right arrow key to select.

5. Press the “Enter” button to accept the new device.

6. Follow the prompts on screen or use the Help (?) button for further information.

108

FireNET 4127 I & O Manual v1.90 UL

8.2.1.4.2 To Delete a SLC Loop Device

1. Select the ADD/DELETE DEVICE menu.

2. Using the scroll keys to navigate, select the applicable loop that the device resides on, and then select the device to be deleted.

3. Press the “ENTER” button to perform the deletion.

8.2.1.5 Edit Device Attributes

Selecting EDIT DEVICE ATTRIBUTES from the EDIT CONFIGURATION MENU allows the user to set attributes specific to each SLC loop device on the system. After selecting the SLC loop (1-4) where the device is located, the user can scroll through each SLC device on that loop and set attributes specific to that device.

The device attributes are different for the three different point types - Detector, Input, or Output. Following is a description of the attributes that can be set for each point type. o Set

This option allows the user to set the software zone this device will reside in. Do not use zone 0 for SLC loop devices. o Edit Location Text

This option allows the user to scroll through and enter up to 40 characters describing the device location o Change Sensor Type

This option allows you to change the type of sensor currently assigned to this address. Choices are ALK-V Photoelectric,

ALG-V Photoelectric Smoke, AIE-EA Ionization Smoke, ATG-EA

Heat Sensor, ACA-V Multi Sensor or ALG-DH analog duct sensor.

Sensitivity

This option allows the user to set both the day and night sensitivity levels for this device. Setting the percent per foot obscuration of smoke that must occupy the detectors chamber to cause an alarm, programs smoke detector sensitivity. Setting the temperature that must be reached to cause an alarm (degrees F) programs the heat detector sensitivity. Day and night sensitivity times are configured in another menu location. o Set Input Action

This option allows the user to change the detector’s (sensor) action type to Fire or Supervisory.

109

FireNET 4127 I & O Manual v1.90 UL

• Output Modules (R2M (all models), SOM (all models), ASB and DH98AR Relay)

Zone

This option allows the user to set the software zone this device will reside in. Do not use zone 0 for SLC loop devices. o Edit Location Text

This option allows the user to scroll through and enter up to 40 characters describing the device location. o Delay Stage 1

If you are using staged controls. This option sets the delay for stage 1 in 30 second increments up to 5 minutes maximum (R2M modules and DH98AR Relay only). o Delay Stage 2

If the attribute ‘Silenceable’ is set to Yes (see below), Delay Stage

2 will become visible. This option sets the delay for stage 2 in 30 second increments up to 5 minutes maximum (R2M modules only).

Attributes

General Alarm mode (Common Fire Alarm): This option allows a user to enable or disable the global General Alarm mode for a selected output(s). When enabled, the output follows the panels

General Alarm mode (see 8.2.1.2). When disabled, the output will not follow the General Alarm mode, allowing control by cause and effect logic statements.

Silenceable: This option allows a user to program whether the selected output is silenceable via the alarm silence button on the front panel or not (not available for DH98AR Relay).

Pre-Alarm Output: This option allows a user to assign a selected output(s) to the Pre-Alarm Group. When assigned to this group, any sensor going into pre-alarm will cause this output group to activate.

Trouble Output: This option allows users to assign a selected output(s) to the Trouble Group. Any input assigned to this group, or any panel trouble will activate all the outputs assigned to this group.

Pattern (SOM and ASB only): This option allows the user to select the output pattern for the SOM module. Selections are

Continuous, Temporal and March.

Test Device Output: This option allows the output to be manually turned on or off by the user.

110

FireNET 4127 I & O Manual v1.90 UL

NOTE

: Panel Outputs can be programmed into three primary categories:

• Common o When output attribute flags are set for general event categories, the output operation will follow the common activation of that event type. General Alarm mode should be set to “common” for this operation.

• Zone o When outputs are assigned to zones, the output operation can be triggered on a zoned basis. General alarm mode should be set to “zonal” for this operation.

• Programmable o When outputs are not assigned to general event categories via output attributes, the output operation is programmable by using Cause and Effect.

• Input Modules (FRCM (all models), DIMM, CZM)

Zone

This option allows the user to set the software zone this device will reside in. Do not use zone 0 for SLC loop devices. o Edit Location Text

This option allows the user to scroll through and enter up to 40 characters describing the device location. o Set Input Delay

Input delays can be programmed (where acceptable by the

Authority Having Jurisdiction) in 10-second increments up to 2 minutes. o Set Input Latch

Each input can be programmed as latching or non-latching.

Latching requires the panel to be reset before the condition is cleared. Non-latching resets the condition automatically when the input returns to normal. o Set Input Action

Input action defines the type of event that occurs when the input is activated. Choose between Trouble, Pre-Alarm, Supervisory,

Auxiliary, Silence Alarm, Reset, Transparent, Disablement, Test, or

Fire. o Set Input Type (FRCM and DIMM only)

This option allows the programmer to define the type of device being monitored, and if the initiating circuit is configured as normally open or normally closed. Available selections are Pull

Station, Waterflow, Valve Monitor N/O, Valve Monitor N/C, Duct

Detector, Detector, Reset Alarm, Temperature, Pressure, Level,

Position, Power, General Supervision, General Purpose N/O EOL,

General Purpose N/C EOL, General Purpose N/C no EOL, and

Waterflow Non-Silence. The selected Input Type will appear as part of the message on the LCD display during device activation.

111

FireNET 4127 I & O Manual v1.90 UL

o Test Device Ouput (LED)

This option allows the module LED output to be manually turned on or off by the user. This is helpful for locating installed modules by turned on their indicator.

8.2.1.6 Auto Learn

Auto Learn is a utility that can be run to quickly identify and enroll all of the SLC loop devices on the FN-4127 control panel as well as the panel’s internal structure and default network routing and nodes.

Auto Learn can be run from the AUTO LEARN sub-menu at any time. When Auto Learn is run, the panel searches each of the 4 possible SLC loops for SLC devices. When it finds a device it identifies which type of device it is, and creates a basic configuration for that device. The installer can then go back and customize the configuration accordingly.

WARNING:

Running Auto Learn will erase all system programming.

8.2.2 Set Times

ACCESS LEVEL 3 MENU

EDIT CONFIGURATION

►SET TIMES

VIEW PRINT EVENT LOG

PRINT CONFIGURATION

SYSTEM DISABLEMENTS

LOOP DATA TEST

The SET TIMES menu option allows the installer to set the smoke detector calibration time, the day / night sensitivity times, and the Sounder Time-Out for the FireNET panel.

8.2.2.1 Calibration Time

This menu option sets the time of day that the panel will perform calibration on the system smoke detectors. Default is 02:00. The time may be adjusted with the up/down arrow keys. The calibration time should be chosen based on an expected time of day when the environmental conditions in the building are stable.

112

FireNET 4127 I & O Manual v1.90 UL

8.2.2.2 Day / Night Times

Day / Night sensitivity is used when you expect environmental conditions to regularly change in the building. By setting the sensitivity lower or higher at certain times of the day or night, false alarms caused by changing environmental conditions may possibly be avoided or reduced.

This menu option allows the installer to program the start and end times for each day of the week for day sensitivity mode. Any times that fall outside of the programmed day start and stop times are considered to be night sensitivity mode.

8.2.2.3 Set Sounder Time-Out

This option allows the user to program the NAC circuit activation time during a Fire alarm. At the end of the programmed time, the notification appliance circuits will turn off automatically. Valid selections are from 5 minutes to 60 minutes, in 5-minute increments. The default setting is 0 minutes, which disables the sounder time-out feature.

NOTE:

This value must be set to zero (0) minutes to be compliant with UL864 9 th

Edition. (See Prefix of this manual for additional details).

8.2.3 View Print Event Log

ACCESS LEVEL 3 MENU

EDIT CONFIGURATION

SET TIMES

►VIEW PRINT EVENT LOG

PRINT CONFIGURATION

SYSTEM DISABLEMENTS

LOOP DATA TEST

The View Print Event Log menu command allows the user to view the system’s 500event memory log. Any condition outside of normal panel operation generates an entry into the event log. The event log is a very useful tool for troubleshooting system problems or verifying that certain activities, such as Fire Drills, actually took place.

The View Print Event Log menu option is covered in greater detail in Section 10 -

Testing and Troubleshooting.

113

FireNET 4127 I & O Manual v1.90 UL

8.2.4 Print Configuration

ACCESS LEVEL 3 MENU

EDIT CONFIGURATION

SET TIMES

VIEW PRINT EVENT LOG

►PRINT CONFIGURATION

SYSTEM DISABLEMENTS

LOOP DATA TEST

If the system is equipped with a printer, all SLC Loop configuration information can be printed using this menu option. See Section 3.7 for information on adding a printer to the FireNET system.

You can filter the printout by loop or by zone if desired.

8.2.5 System Disablements

ACCESS LEVEL 3 MENU

EDIT CONFIGURATION

SET TIMES

VIEW PRINT EVENT LOG

PRINT CONFIGURATION

►SYSTEM DISABLEMENTS

LOOP DATA TEST

The System Disablements menu option allows the installer to temporarily disable the system printer (if equipped), the panel buzzer, ground fault detection, and set buzzer silence access level. The panel buzzer and ground fault detection are enabled in the panel’s default condition. The buzzer silence access level is set to 2 by default.

Disabling any of these options places the panel in a trouble condition. Each disablement of these system devices must be manually reset.

Disabling system devices is typically used on systems where there are intermittent problems, while the problems are being corrected. It is important to note that these features should not be permanently disabled (except printer option). The installer must make sure buzzer and ground fault detection are re-enabled after corrections to the system are complete.

NOTE

: The following values must be set to be compliant with UL864 9 th

Edition. See prefix of this manual for additional details.

• Buzzer – Enabled

• Ground Trouble – Enabled

• Buzzer Access Level - 2

114

FireNET 4127 I & O Manual v1.90 UL

8.2.6 Loop Data Test

ACCESS LEVEL 3 MENU

EDIT CONFIGURATION

SET TIMES

VIEW PRINT EVENT LOG

PRINT CONFIGURATION

SYSTEM DISABLEMENTS

►LOOP DATA TEST

Loop Data Test is an installer or service level diagnostic test that is explained in greater detail in Section 10 - Testing and Troubleshooting.

115

FireNET 4127 I & O Manual v1.90 UL

Section 9 - Loop Explorer Software Programming

This section covers the use of the FireNET Loop Explorer software package. The

FireNET 4127 is an extremely flexible and robust system that can grow modularly as the application requires. To take full advantage of the power and flexibility of the

FireNET 4127 the Loop Explorer software must be used for programming the system.

This section is intended to be an overview of the Loop Explorer programming process.

Loop Explorer includes a very comprehensive Help system that can help answer any questions not covered in this manual.

9.1 PC Requirements

FireNET Loop Explorer software requires the following minimum PC requirements.

• PC with Pentium II 300 MHz or higher processor; Pentium III recommended.

• Microsoft Windows 98SE or later operating system; Windows 2000 or XP recommended.

• 100 MB of available disk space

• 64 MB RAM

• PS2 Microsoft Mouse or compatible pointing device and PS2 Keyboard

• CD ROM Drive

• VGA 256 color monitor. SVGA recommended @ 1024 x 768. Hardware acceleration minimized.

• Serial communication port that can be configured as COM1-8

• FN-X187 or FN-S187 RS232 serial programming cable (See table 1.2.1)

NOTE

: Revision level of software and firmware at the time this manual was released:

• Loop Explorer: 6.1xx

• FireNET panel firmware: 4.0xx

9.2 Installing Loop Explorer

The Loop Explorer software CD includes an Autorun file which automatically launches the Loop Explorer installation routine when the CD is placed in the PC’s CD ROM drive.

Follow the directions that appear on the screen to install FireNET Loop Explorer to your

PC hard drive. Open the ReadMe file provided on the Loop Explorer CD for additional details on how to install Loop Explorer software.

116

FireNET 4127 I & O Manual v1.90 UL

9.3 Launching Loop Explorer

Once FireNET Loop Explorer is installed to your PC’s hard drive, you can launch it from your Start Menu under Programs - Hochiki - FireNET Loop Explorer. Click the FireNET

Loop Explorer icon to launch the program.

9.4 Connecting Your PC to the FireNET 4127

The easiest way to transfer your system configuration data between the FN-4127 and the PC running the FireNET Loop Explorer software is to directly connect your PC to the panel. This section provides instructions on how to connect the PC to the FireNET

4127 control panel.

1. Obtain or locate a FN-X187 or FN-S187 serial programming cable.

2. Plug the DB9 connector into an open COM port on the PC. (You will need to note what COM port number this has been configured as)

3. Plug the other end of the serial cable into the RS232 port on the back of the cabinet door - (J5 labeled “PC”).

4. In the File menu, click on Options and set the COM port to the appropriate setting (COM 1-8)

9.4.1 Using PC Connect

9.4.1.1 Using Transfer

1. Click on the Connect icon on the tool bar or click File, P.C. Connect, to search the panel Network for attached panels and config in Loop Explorer.

2. A Password window will appear. Enter the correct password for access to the panel.

3. Press the Connect button.

NOTE:

This password protects the panel’s configuration data from unauthorized access. It is important to set and record the password that has been assigned to the panel for future and ongoing access to the configuration. This allows each FireNET installation to have security protection for the site specific programming.

117

FireNET 4127 I & O Manual v1.90 UL

4. Wait until Loop Explorer has searched all 64 possible panels, and it will then show the PC connection window.

5. The Network tab allows you to transfer or retrieve data to the selected panel or panels.

The panels that are on the

Synchronize

Upload/Download to Panel Arrow network are shown as a list.

Depending on the time stamp information (Modified) of both,

Loop Explorer will suggest a transfer from PC to panel, or panel to PC.

6. Click the checkbox to select the panels desired for synchronization. Direction of Config transfer can be changed by clicking Change, in the toolbar, above the PC connect detail view.

Click Synchronize to activate the process. This will upload or download a configuration according to the orientation of change, indicated by an arrow in between Modified heading, and Panel Network.

7. Click

to compare panel configuration data against the PC configuration.

• “=” means the configuration data is the same.

• “←“ or “→” means they are not, and arrow suggests the transfer direction for correct synchronization.

8. Click the Synchronize Time button to set the time and date in the FireNET panel. This operation will set the time/date in all networked panels to the time/date in the PC being used for programming

WARNING: Before downloading or uploading panel/network configuration, the user should be aware of the resultant effect of transferring configuration data. When downloading to a panel/network from the PC (Loop Explorer), the configuration data in the panel/network will be erased and overwritten with the configuration data from Loop Explorer project file (*.hsa). When uploading from a panel/network to the PC, the opposite will occur. The Loop Explorer project file will be erased and overwritten. Uploading from the panel/network should only be performed for emergency recovery in the event that the Loop Explorer project file has been lost or corrupted. Upload operation is not intended for routine use. The derivative uploaded project file will include panel/network configuration data, but will not include common Loop Explorer data not stored in the panel/network memory. Common practice should be to always use the source

Loop Explorer project file and download to the panel/network.

118

FireNET 4127 I & O Manual v1.90 UL

9.4.1.2 Using the Hochiki Unlock Code

IF you do not have the correct password, the

Hochiki Unlock Code must be used to remove the existing password and create a new one.

1. If you input the incorrect password an additional window will appear, asking if you wish to request an unlock code from

Hochiki. Press the Yes button.

2. An additional window will appear, showing the encrypted unlock code. The code will automatically be saved to the Windows clipboard. Paste this code in to an email. From the Tool menu, select Submit Bug/Comment Report to create an email that will send the encrypted unlock code to [email protected]

for decryption.

3. Upon customer verification, Hochiki will email the decrypted unlock code to the user. Upon receipt, open P.C. Connect.

4. In the Password window, click on the Enter

Unlock Code.

5. The Password window will increase in size to show the Enter Unlock Code section.

6. Enter the decrypted unlock code in the appropriate box.

7. Press the Unlock button. The panel will revert back to a default password (1111).

8. A new password can now be installed for the panel.

NOTE

: The encrypted unlock code and its decrypted counterpart is only valid for

24 hours. After 24 hours, the panel will create a new encrypted unlock code.

119

FireNET 4127 I & O Manual v1.90 UL

9.4.1.3 Using the Event Log

The Event log screen gives you the option of uploading the event log from a given panel from its stored memory, and to view it from your computer. The panel event log is capable of storing up to 500 events. The events are stored in order of priority and occurrence. When the event log is full, the oldest and lowest priority event will be dropped as new events occur.

1. Select the panel from the drop-down list box on the Event Log tab.

2. Click Fetch to obtain the log from the panel and display it Event Log window.

3. You may export the panel event log by saving the log to a file. Press Save to create/save the event log as an Excel spreadsheet file (*.csv).

9.4.1.4 Device Analog Values

Sensors (detectors) on a SLC loop have Analog Values which represent current value

(clean air), last calibrated zero point, and last calibrated fire point. These Analog Values relate to the health of the sensor. These values can be retrieved using the Analog

Values window.

1. Choose a panel from the drop-down list box on the Analog Values tab.

2. Select a Loop on the panel using the buttons.

3. Click Fetch to retrieve the values of all sensors on the chosen Loop.

4. Click and select a device from the list to show the reading, and the calculated percentage of the Health. Press Save to create/save the Analog Values as an

Excel spreadsheet file (*.csv).

120

FireNET 4127 I & O Manual v1.90 UL

9.4.1.5 Using Virtual Panel

The virtual panel will replicate the display and controls of the selected panel. Choose a panel from the drop-down box, then click start to mimic the panel display; you will be able to use all the buttons in the normal way. The LED’s and LCD screen on the Virtual

Panel display will indicate real-time status of the FireNET control panel selected.

9.4.1.6 Using the Monitor window

The Monitor Mode window allows you to monitor the actual ASCII event text via direct serial output from the panel connected on the chosen COM port. All event data will be displayed as it occurs from the connected panel. This is useful for seeing the real-time panel events being sent over the panel’s COM port. Press Save to create/save the

Monitor Mode activity as a Word file (*.rtf).

121

FireNET 4127 I & O Manual v1.90 UL

9.4.2 Setting a COM Port

If you cannot connect to your panels, it may be necessary to adjust your COM Port settings

On some computers, it may be necessary to change the communications port used to transfer data to and from the panel. The default is COM 1, however it is fairly easy to change the selected COM port.

To Change the COM port:

1. Open File: Options from the Menu bar dropdown list.

2. An

window (as shown) will appear, with the first tab COM Port selected.

3. Select the COM port you wish to use.

NOTE:

Windows COM Port settings should be as follows:

Baud

• 8 Data Bits

Parity

• 1 Stop Bit

• Flow Control None

NOTE:

For computers that do not have COM (serial) ports, a USB-to-COM adapter will be needed. There are several 3 rd

party brands, types, and models available. They do not all perform the same and many have unique idiosyncrasies. Hochiki recommends the brand IO Gear model GUC232A unit or equivalent.

9.5 Getting Familiar with Loop Explorer

The FireNET Loop Explorer main screen contains a user-friendly interface that allows the installer or service person to easily navigate to any panel, circuit, loop, zone, or device on the system and quickly make any configuration changes required. (See

Figure 9.5) This section provides a basic overview of the various elements of the

FireNET Loop Explorer user interface.

122

FireNET 4127 I & O Manual v1.90 UL

Figure 9.5 FireNET Loop Explorer Main Screen

9.5.1 User Interface

As shown in Figure 9.5, the Loop Explorer main interface has several different sections that make programming the FN-4127 control panel fast and easy to do.

The main screen has two main windows, the navigation tree on the left and the detail view on the right. The toolbar at the top allows the user to quickly carry out any action, just by clicking one of the buttons.

The Navigation tree acts like Windows Explorer allowing you to expand and contract levels using the + and - boxes, situated to the left of the items.

The detail on the right shows the selected items content. In Figure 9.5 the table shows what devices are currently connected to a loop. The detail view reveals extra information not given in the tree such as device type, location text and zone information. These cannot be changed through the detail viewer, but must be changed using the edit menus. Selecting the item from the table will expand that level. Or you may do so by clicking an expansion box in the site tree. The menus at the top can be expanded in the usual fashion and some toolbar options will also appear in the menus.

All of the options at the top on the toolbar will become active or inactive according to what is selected in the Navigation tree and Device table.

123

FireNET 4127 I & O Manual v1.90 UL

9.5.1.1 Expanding and contracting windows in Loop Explorer

You may Expand and contract any levels, in the navigation tree, shown as positive [+] or negative [ - ] boxes. To expand one level, click on the positive box next to the level you wish to expand. In figure 9.5, Hochiki Panel will be expanded. Click on the [+] box, and the level is expanded, revealing, it has two loops, and a local panel I/O (all panels have a local panel I/O). You may further expand each level by clicking on its [+] box, or double clicking on the name of it, i.e. showing the devices in a loop. To contract a level, do the reverse, click on its

[ - ] box, which will contract that level, hiding the detail.

To completely expand or contract all positive and negative boxes, select the very top level, which will be the site name in the navigation tree, then use the right click option menu to select either Full Expand, or Full Contract.

9.5.1.2 Menu

Across the top of the main Loop Explorer screen is the menu bar. The menu bar contains 6 pull down menus File, Edit, Explore, View, Tools, and Help, which will be explained later in this section.

9.5.1.3 Toolbar

The toolbar is located directly under the menu bar at the top of the main screen.

The most common Loop Explorer menu commands are duplicated on the toolbar and represented by name and graphical icon.

9.5.1.4 Navigator Pane

Along the left hand side on the main screen is the Navigator pane. The navigator pane is similar to the Windows Explorer style directory tree used in Windows operating systems. The Navigator pane displays all of the components of the system in a tree type structure. System components such as an SLC loop, that have the ability to have additional devices connected to it, can be expanded to show all of the connected devices, or contracted to show just the loop name by clicking on the [+] or [ - ] sign next to its name.

9.5.1.5 Device Table

The device table is the table of cells that take up the most space on the main screen. This table displays a list of all the devices, circuits, or sub-addresses that are associated with the device currently selected in the Navigator pane. Devices in the Device Table can be double-clicked on to configure the attributes of that device.

124

FireNET 4127 I & O Manual v1.90 UL

9.5.1.6 Items / Notes / Web Section

The Items/Notes/Web section at the bottom of the main screen has tabs along the left side that switch the content of the section from Items, Notes or Web view. In Items view, a list of items that can be added to the device currently selected in the Navigator pane is displayed. You can double click or drag and drop these items from the Items Pane to the Navigation tree. The Notes view provides a small amount of space to keep notes about the project. Basic word processing type formatting tools are available from a toolbar that is displayed above the Notes section. If the formatting tools are not visible you can display them from the View menu by clicking on Notes Toolbar. The Web view allows a user to connect to the Hochiki web site and access application and technical support services, as well as providing contact information for relevant questions.

9.5.2 Menu and Toolbar Overview

Across the top of the screen is the main menu and just below that is the toolbar. Many of the options on the menu and toolbar are similar to what you have experienced in other Windows based programs. The functions on the toolbar are the more frequently used features of the Loop Explorer software. If you prefer, the toolbar commands also appear in the drop down menus above.

The following sections will give you a brief overview of each of the menu and toolbar functions.

9.5.2.1 File Menu

The File menu is very similar to what you have seen in other Windows based programs. Following is a brief overview of each command on the File menu and its associated function.

New - (Also appears as an icon on the toolbar)

The New menu has two sub menus Config and

Device. Config allows you to start a new FN-4127 project or network. Device will give you a choice of devices that can be added to the current project. The

Device menu option will change and display only those devices that can be added to the section of the panel you are currently working on.

Reopen

Reopen allows a user to select from the 10 most recently opened databases, without the need to search for it on a user’s hard drive or server.

Save - (Also appears as an icon on the toolbar)

Saves the current project to disk.

Save As

125

FireNET 4127 I & O Manual v1.90 UL

Saves the current project to disk with another file name or to a different file location.

Open Network Project

Opens a previously saved FireNET Loop Explorer project.

Close Current Project

Closes the current project being worked on. You will be prompted to save the project if it was not saved prior to selecting this menu option.

Create Loop Emulator File

Allows the selected panel configuration to be exported as a *.hle file, which can be used with the Hochiki True Loop Emulator tool that will be released in the future.

Export Loop Explorer Config

Allows the selected panel network configuration to be exported as a *.lx2 file which can be imported into a Hochiki graphics software package that will be released in the future.

PC Connect - (Also appears as an icon on the toolbar)

Establishes communication between the FN-4127 and the PC. The FN-X187 or

FN-S187 serial programming cable must be installed between the PC and the

FN-4127. The COM port of the PC must be identified to the Loop Explorer software through the Options menu for the communication link to operate properly.

Print/Pre View Panel - (Also appears as an icon on the toolbar)

Print/Pre View will allow you to print a report of all the configuration data for the current project. Several filters are available that allow you to add or delete various sections of the report.

Options

Brings up a new window that will allow you to set global parameters for the Loop

Explorer software such as COM Port number, and default file location that Loop

Explorer saves projects to.

Exit

Close the FireNET Loop Explorer application.

126

FireNET 4127 I & O Manual v1.90 UL

9.5.2.2 Edit Menu

Edit Settings - (Also appears as an icon on the toolbar marked Edit)

Edit Settings will allow you to change the configuration of any device that is currently selected in the Navigator pane. For example if you have clicked on the FN-4127 control panel in the Navigator pane, the configure panel window will open up allowing you to change the options specific to that FN-4127 control panel.

Change Device Type - (Also appears as an icon on the toolbar)

This menu option will only be active if an SLC loop device is selected in the

Navigator pane or the device list table. By selecting Change Device Type you can easily change any SLC loop device to another type of device. For example you can change an R2M dual relay module to an FRCME-4 input module.

Quick Config - (Also appears as an icon on the toolbar)

The quick config menu option is only active when a panel has been selected in the Navigator pane. Quick config opens up a table that shows every SLC device on the loop and allows you to edit the zone number and location text of each

SLC device shown.

Zone Manager - (Also appears as an icon on the toolbar)

The Zone Manager menu option brings up a new window with a list of zones 0-

500 available on each system. By clicking on each zone number in the list, you can quickly view all of the SLC devices, or panel inputs and outputs that are assigned to that zone. Zone Manager also allows you to drag and drop SLC devices and panel I/O to a particular zone. The alarm verification feature can be enabled or disabled from Zone Manager on a per zone basis.

Action Messages- (Also appears as an icon on the toolbar)

The FN-4127 has 11 predefined action messages that can be assigned to inputs on the system. These action messages appear on the main panel LCD status display when the input they are assigned to activates. The 11 predefined action messages that the system includes are:

• Fire

• Trouble

Alarm

• Auxiliary

• Silence

• Reset

Drill

• Transparent

In addition to these 11 predefined action messages you can add 9 custom action messages of your choosing. These custom messages can be up to 15 characters long.

127

FireNET 4127 I & O Manual v1.90 UL

Select the Action Messages menu option to create/edit these custom action messages.

Site Details

Loop Explorer defines a Site as a single FN-4127 panel or multiple FN-4127 panels configured in a network. The default name for a site is “New Site”. Using the Site Details menu option you can give the site a new custom name of up to

25 characters. The site name only appears in the Loop Explorer software and does not appear on the panel display.

C&E Summary

The C&E Summary menu option opens a new window that has a summary view of all Cause and Effect relationships on the system. A cause and effect relationship is a custom program you create to link any input or group of inputs on the system, to any output or group of outputs. The cause and effect relationships on the FN-4127 system can be extremely powerful and are explained later in this section of the manual.

Delete - (Also appears as an icon on the toolbar)

The delete menu option will delete the device that is selected in the Navigator pane from the system. As a safeguard to inadvertently deleting an entire panel,

Loop Explorer requires that all of the devices on the SLC loops be deleted before a panel can be removed from the configuration.

128

FireNET 4127 I & O Manual v1.90 UL

9.5.2.3 Explore Menu

The Explore Menu has basic commands that allow the user to navigate and change the appearance of the

Navigator pane.

The Up menu command moves the selection in the Navigator pane up one level.

For example, if an SLC loop device is selected, clicking Up will move the selection to the Loop level. If a loop is selected, clicking Up moves the selection up to the Panel level.

Full Expand

The Full Expand command fully expands the item currently selected in the

Navigator Pane. If a panel is selected, Full Expand will show all of the panel’s

Loops, SLC Devices and I/O circuits with a single click. If the Site is selected, all panels will be expanded, along with all Loops, SLC Devices and I/O for every panel. With a single click Full Expand is the equivalent of clicking the [+] box next to every panel and loop in the Navigator pane.

Full Contract

Full Contract is the opposite of Full Expand. When you click on Full Contract, the selected item is contracted to show only the very top level of that item.

Where Used in C&E

The Where Used in C&E option will display the name of all Cause and Effect relationships assigned to the selected SLC or I/O device. This summary can help establish where and how an input or output is being used in your custom

C&E programming.

129

FireNET 4127 I & O Manual v1.90 UL

9.5.2.4 View Menu

Normal Details / List Icons

The first two menu options change the appearance of the Device Table. By choosing Normal Details, the

Device Table displays the standard table data with separate cells for Item, Type, Location Text, and Zone.

By choosing List Icons, the Device Table shows only icons and the addresses of the system devices.

Show Task Pane

The task pane is a small window that has a hyperlink list of the most common tasks or operations that are done to configure a typical system. Clicking this menu option shows or hides the task pane.

Show Long Device Names

This option changes the display of the Navigator pane. If Long Device Names is selected (checkbox next to menu option) the full name of each device (Dual

Relay Module) is shown in the Navigator pane. If Long Device Names is not selected the part number only (R2M) displays in the Navigator pane.

Show Notes Toolbar

If selected, this option displays the formatting toolbar on the Notes section at the bottom of the main screen. If not selected the formatting toolbar is not displayed.

Show Toolbar

The main toolbar is located just below the menu bar at the top of the main screen. Clicking this menu option shows or hides the main toolbar.

Show Grid Lines

Clicking this menu option shows or hides the grid lines in the Device Table.

Show Status Bar

The status bar is the small gray bar located at the very bottom of the main screen. It is divided into sections that provide information related to the operation you are performing in Loop Explorer. Clicking this menu option shows or hides the status bar.

Bold Fonts

When selected, the fonts are bolded in the Navigation Pane and the Device

Table.

130

FireNET 4127 I & O Manual v1.90 UL

9.5.2.5 Tools Menu

Flash

The flash memory that the FN-4127 panel firmware utilizes can easily be upgraded as Hochiki adds new features to the product in future releases. This menu option will open a new window that will allow you to

“flash” upgrade the FN-4127 panel firmware. This utility should only be used under the direction of Hochiki America technical support by Hochiki certified service professionals.

NOTE:

The Flash utility only supports COM1-4

WARNING!

Improper use of the

Flash option can result in damage to the panel’s firmware and operation.

When performing a “flash” upgrade to a panel, contact Hochiki Tech

Support to ensure proper firmware versions and compatibility.

Before beginning the “flash” upgrade process, be sure to review and then follow the exact instructions outlined in the Flash Upgrade window when executing the process.

Submit Comment / Bug Report

Selecting this menu option will launch your computers email program and open a new email addressed to Hochiki America technical support. You may use this to send comments or bug reports to Hochiki via email.

9.5.2.6 Help Menu

Loop Explorer contains a very comprehensive help system that can answer most of your programming questions.

131

FireNET 4127 I & O Manual v1.90 UL

ain Tool B ar Icons

ac tions that a

New Pane l

Save

Type...

Delete

Allows you t to add anothe icon toolbar if f you have op of the Nav igation tree.

will

Allows you t to add anothe nel. n on the icon u

Allows you t to add anothe loop. You wil ll op in the Navigati on tree. to disk. ou to change t ation gator

127 the y be active if an SLC loop device is se lected in the N ice hange Device an oop device to e of device. For example you selected in t the Navigator y deleting an entire panel, s s a

Loop Explor hat all of the d be deleted bef fore a panel c

Manual

Quick Con fig

Print/Previ ew

Panel

The Where Used in C&E option will di me of all Cause selected SL

and Effect re

C or I/O devic e p g display whe n the input th that ction es. m

•

• Fire

• Trouble

•

• m

• Superviso

• Auxiliary ory Alarm

• Silence

• Reset

• Fire

•

Drill ent redefined acti s

Loop Explore on a panel. brings up a n with mber in the li st, you can

C devices, or r panel inputs and outputs that are assi

Manager all ows you to dr rag and drop SLC devices and panel I/ O to a particu verification f e enabled or zone basis. you to print a r he allow you to a dd or delete various sect eport.

4127 I & O Manual

PC Conne ct

Help

Establishes communicati on between t and installed bet C and the FN-4

COM port of f the PC must

Explorer sof ftware through communicat tion link to op

Loop Explor rer contains a system that can answer m questions.

ms Pane I Icons

Pane. All hardware i to pull dir ectly into th and simply.

s a 2-Loop Panel to th e site.

2 Loop

4 Loop

Network D-N Networ rk Annuncia

Network r

I I/O Module or

Annunciator r to a panel

Manual

9.5.4.3 Device Icons

DH98-A

DH98-AR

FRCME

SOM

R2M

ALK-V

ALK-V2

ALG-V

ATG-EA

AIE-EA

ACA-V

CZM

DIMM

ASB

AMS

Adds a DH98-A or a DH98-AR analog duct detector to a Loop

Adds an addressable FRCME contact monitor module

Adds an addressable Supervised Output Module to a Loop

Adds an addressable Dual Relay Module to a Loop

Adds an ALK-V or ALK-V2 Analog Photoelectric

Smoke Detector to a Loop

Adds an Analog Photoelectric Smoke Detector to a

Loop

Adds an Analog Heat Detector to a Loop

Adds an Analog Ionization Smoke Detector to a

Loop

Adds an Analog Multi (Photoelectric and Heat)

Detector to a Loop

Adds an addressable Conventional Zone Module to a Loop

Adds an addressable Dual Input Module to a Loop

Adds a Aux Powered Sounder to a device

Adds an addressable AMS Pull-Station

135

FireNET 4127 I & O Manual v1.90 UL

9.5.4.4 Cause and Effect Icons

Cause and

Effect Action

Opens the Cause and Effect wizard for creating a

Cause and Effect Action.

Cause and

Effect

Disablement

Test Mode

Opens the Cause and Effect wizard for creating a

Cause and Effect Disablement.

Opens the Cause and Effect wizard for creating a

Cause and Effect Test Mode.

9.5.4.5 Notes Pane

The Notes pane allows the user to add notes about the project. It includes many features found in a word processor program which are listed in the right click options menu. The Notes feature operates much like a simple version of

Microsoft Word®.

The menu icons items in the Notes toolbar are as follows:

Undo-

This action will undo the last change made to the text in the box.

Cut, Copy, Paste-

These allow you to Cut or Copy text, and to Paste text into the Notes. You can use Cut, Copy and Paste to move text to and from other applications.

Select All-

This will select all the text in the text box, ready for a change that will affect the entire text.

Print-

This will bring up the usual print dialog, from where it’s possible to select a printer, and print out the contents of the Notes.

136

FireNET 4127 I & O Manual v1.90 UL

Font-

Select this to bring up a Font Dialog box, which allows you to change the font size, and style of the selected text, and any text written after the cursor.

Bold-

This will change the selected text to Bold

Italic-

This will change the selected text to italic.

Underline-

This will change the selected text to underlined.

Word Wrap-

Word wrap is useful if you want to make sure you view all the text in the box at the same time. If there is more text than the length of the Notes pane, then the text will wrap to the next line.

Left Justify-

This will change the selected text to a left justification, like the text on this page.

Center Justify-

This will change the selected text to a center justification.

Right Justify-

This will change the selected text to a right justification.

Insert Date and Time-

Use this to insert the current date and time, in the format to which your computer has been set to.

Import Text from File-

You may import text from a .txt or .rtf file, but note that all text in the text box will be overwritten with the text in the file. If you do not want this to happen, select the text in another application, and copy and paste it into the Loop Explorer

Notes.

Save to File

This will save the contents of the Notes pane to a selected file with the .rtf format file extension, which can then be used in any other text editor.

Hide Toolbar-

Check this option to hide the toolbar, which attaches to the top of the Notes page. The toolbar has the same options as the Right click menu.

137

FireNET 4127 I & O Manual v1.90 UL

9.6 Developing a Site

9.6.1 Creating a New Site

1. When starting Loop Explorer you will be presented with a Loop Explorer window.

2. If you wish to start a new Network Project,

Click on Blank FireNet Network Project, and click OK.

3. You will now be asked to save the project.

Select a suitable location and click save. This will now save the empty project. Any further changes made to the new site will automatically be saved to the file just created if AutoSave is enabled in Options. If not, you must click the Save icon after changes are made. You will now be presented with a blank project with only Cause and Effect in your navigation tree, and the “Welcome to

Loop Explorer” task pane.

138

FireNET 4127 I & O Manual v1.90 UL

9.6.2 Editing an Existing Site

Click on Open an Existing Project and either enter the path by typing it in or click Find

File to browse and find the site you wish to open. Click Open to open it. The displayed file format is .HSA, which is unique to Loop Explorer, and you will only see Loop

Explorer files (.hsa) in the directory you are viewing.

9.6.2.1 Finding a Recent Project

1. Open Loop Explorer.

2. In the menu, click the File: Reopen.

3. Then choose the file from the list. Only the ten most recently opened files will be displayed.

9.6.2.2 Opening a new project file while within a Loop Explorer project file

1. Click

This will ask if you wish to open a different site.

2. Click the Close box in the top right-hand corner to exit this window and return to your current site, or you may continue to open and create a new project. Click

Exit to exit the Loop Explorer program.

NOTE

: You may also close a project by clicking File: Close Current

Project

9.6.2.3 Opening an existing project while in a different Loop Explorer project file

1. Click

. This will show a browsing window.

2. Select the desired project and click OK to open it or Cancel to exit the window.

9.6.2.4 To Change the Name of a New Site

1. Click on the Site name in the Navigation tree after creating a new site.

2. Click on Edit from either the right click menu or the toolbar.

3. Enter the desired site name (25 characters maximum).

139

FireNET 4127 I & O Manual v1.90 UL

9.6.3 Saving a Site

You may save the project you are working on at any moment, just by clicking on the

Save icon in the toolbar. This will save all changes you have made since your last save point. The Save option will only become available if you make changes to an existing project, otherwise it will be inactive. By clicking Save, you will overwrite the current project file, and replace it with the new configuration.

If you have never saved the particular project before now, it will prompt you to choose a filename and folder to be saved into. This can be done at any time, using the Save

As…

option.

If you try to close a project without saving it, Loop Explorer will ask for confirmation before closing the project.

9.6.3.1 Using Autosave

A user has the option to set up Autosave, which will automatically save the project at a specific interval. Saving will not be done if the PC connect screen is open.

To Enable Auto Save:

4. Open File: Options from the Menu bar.

5. An window (as shown) will appear, click on the Other tab. the checkbox.

7. Select the appropriate Interval you wish the project to Autosave.

140

FireNET 4127 I & O Manual v1.90 UL

9.7 Configuring Panels to a Network

The FireNET 4127 analog addressable fire system is capable of supporting a maximum of 64 nodes (panels and network annunciators) and a maximum of 500 network-wide zones. Any number of devices can be allocated to any zone ensuring that any system configuration can be easily accommodated.

To ensure that the system is installed and commissioned with the minimum of trouble, it should be carefully planned before the installation is begun. This involves allocating an address to each device and allocating a message of up to 40 characters (including spaces) to each address to assist in the location of the devices. Devices should then be grouped into zones in accordance with the appropriate fire detection systems design standard, building plans, and local fire codes. The FireNET 4127 control panel offers an extensive list of features and options for fire alarm control and monitoring that can be configured via Loop Explorer or the front panel controls.

9.7.1 Adding a Panel

Upon starting a new network you will automatically be asked if you want to add a new panel to the project by using the Panel Wizard. Click yes, and the Panel Wizard will start, or click No to directly edit the configuration settings of the new panel.

To add another new panel to the configuration you may do it several different ways, using the main menus, toolbar, and right click menu.

9.7.1.1 Using the Panel Wizard

The Panel Wizard will easily help you to add a panel to your network, and will set up a lot of the default values for you.

These default values can be edited or changed later using the panel configuration screen.

1. Click on the Site in the Navigation tree.

3. You will be asked if you want to use the Panel Wizard.

Click the Yes button.

4. You will see the New Panel Wizard window open. Click the Next button.

5. The first screen will be Panel Text. You will be asked to give the new panel a name (up to 15 characters). If you wish you can add some descriptive text that will be displayed on the panel’s LCD screen when it is in the idle state (i.e.

Second-floor lobby). Click the Next button when finished.

NOTE

: When adding panels via the Panel Wizard, Loop Explorer will automatically assign addresses to the panels, starting from 1, and going up in order.

6. Choose the number of Loops the panel will have (2 or 4), and then click the

Next

button.

7. Choose the General Alarm Mode for the panel (Common, Zonal, 2-Stage), and then click the Next button.

141

FireNET 4127 I & O Manual v1.90 UL

8. A Review screen will appear. If your selected values from the previous screens are correct, click the Next button. If you wish to make changes, click on the Back button.

9. You will come to the Finish screen. You will be given three choices:

• Edit location text using Quick Config

• Edit the Advanced Panel Settings

• Return to Explorer

Select the appropriate the choice and click the Finish button.

9.7.1.2 Using the Menu bar

1. Click on the Site in the Navigation tree.

3. You will be asked if you want to use the Panel Wizard. Click the No button.

4. You will see a Protocol Options window; select the panel you wish to use.

NOTE:

To select either a 2 Loop or a 4 Loop panel, select Hochiki America Panel.

5. You will immediately be asked to configure the panel using the Configure Panel

Settings

window.

6. Once the panel has been configured, press the OK button.

9.7.1.3 Using the Tool bar

the button on the toolbar

2. You will be asked if you wish to use the Panel Wizard. If you wish to use Panel Wizard, follow Steps 3-9 of 9.7.1.1. If you DO NOT wish to use Panel Wizard, follow Steps 4-6 of 9.7.1.2.

9.7.1.4 Using Navigation Tree

1. Right click over the site in the Navigation tree, and click New Panel.

2. You will be asked if you wish to use the Panel Wizard. If you wish to use Panel

Wizard, follow Steps 3-9 of 9.7.1.1. If you DO NOT wish to use Panel Wizard, follow Steps 4-6 of 9.7.1.2.

9.7.1.5 Use the Items Pane

1. Select the icon that represents the panel you have selected

2. Drag-and-drop the icon on the Site at top of the Navigation tree.

3. (or) Double-click on the Icon to automatically place the panel in the Navigation

Tree.

9.7.2 Configuring and Editing a Panel

In order to edit the features of a panel, select the appropriate panel icon either in the

Navigation tree or in the Table (if Site is selected in the Navigation tree). To open the

Configuration Node, either:

• In Menu bar, select Edit: Edit Settings…

142

FireNET 4127 I & O Manual v1.90 UL

• Right click the panel icon and select Edit Settings…

Or the icon on the Toolbar…

The Configuration Node will open, allowing you to add or change values in three tabs:

Panel Data, Times, and Network Interface.

9.7.2.1 Configure Node: Panel Data

From the configuration window you can change any of the options from their current settings. The example shows a panel’s default values.

Panel Name

The name of the panel does not have to be unique and it may contain any characters. It is suggested that panels be assigned meaningful names. If panels are not named they will be allocated sequential numbers.

Panel Address

The node number of a panel on a Multi-

Panel Network. The panel address will be incremented every time you add a new panel. It is possible to set the address to a free address by using the drop down menu.

Access Level 3 passcode

Passcode for high-level access to operate all functions of a FireNET panel (i.e. editing the configuration).

Access Level 2 passcode

Passcode for Intermediate access to operate commonly used functions of a FireNET panel, such as silencing an alarm, resetting an alarm, and operating primary panel functions.

Number of Loops

The panel can have 2 or 4 loops. You may not decrease the number of loops unless the loops to be removed have zero devices attached to them.

Loop offset

This option will offset all panel loops by the total of the previous loop count. This is typically used when more than one panel is installed in a network, so that the loop numbering will be sequential across several panels.

143

FireNET 4127 I & O Manual v1.90 UL

The changes to the loop numbering will be shown in the Navigation tree, and all other places where loop numbers are mentioned throughout the program. So if a network had three panels, with 4 loops each at address 1 2 and 3, panels 2 and 3 could be offset, so their loops would change to loops 5,6,7,8 for panel 2, and 9,10,11,12 for panel 3.

General Alarm Mode

There are three options for Gen. Alarm Mode: -

• Common Alarm - All NAC outputs activate from any fire input regardless of which zone they are in.

• Zoned Alarm – NAC outputs in the same zone as the input, which caused the alarm, will activate.

• Two Stage Alarm - Outputs that are in the same zone as the input which caused the alarm will activate while outputs in all other zones will pulse 1 second on - 1 second off.

The factory default setting for the panel General Alarm Mode is Common Alarm. This normally applies to notification appliances and would normally be accompanied by the

Silenceable attributes.

Note

: Panel outputs mapped to zone 0 will operate as common general alarm, regardless of the general alarm setting. Do not assign loop outputs to zone 0.

Pattern

This option allows you to select the output Pattern for the panel’s onboard NAC circuits. Available options are -

• OFF- No pattern is assigned to the NAC outputs

• Continuous- Continuous pattern is assigned to the

NAC outputs

• Temporal- A temporal pattern is assigned to the

NAC outputs

• March Code- A march code is assigned to the NAC outputs.

Graphics System

If a Graphics system is connected to the panel, check this box (future feature).

Panel Text

Panel Text is text displayed on the panel when there are no events showing on the

LCD. The panel text is limited to 40 alpha/numeric characters max.

144

FireNET 4127 I & O Manual v1.90 UL

9.7.2.2 Configure Node: Times

This tab also allows you to set timed features common to panel operations.

Click on the tab Times to reveal these settings.

Day/Night Start and End Times

The start and end times are used to define the Day and Night mode of the panel. During Day mode the sensors Day sensitivity is used, during Night mode, the

Night sensitivity is used. All the default start times are set to 8:00, and the end time is 18:00 (6:00pm). The night-time is considered to be between these two times. You may change the minutes in increments of whole minutes. If you set a start and a finish time the same you will receive an error message. Click on an up or down arrow to change the number in the number box.

Daily Calibration Time

This is the time each day that the sensors will perform their calibration routine.

Calibration occurs once per day and can only be set in increments of 30-minutes.

Choose a Calibration time when building environmental conditions are most stable, for example, early in the morning before daily activities begin.

Sounder Time Out

The FireNET NAC circuits can be programmed to automatically silence after a period of time. The Sounder Time Out option allows you to set the NAC alarm time. The panel default is 00, which disables the feature. Valid selections are from 5 to 60 minutes, in

5-minute increments.

Alarm Verification

The alarm verification time value can be set between 5 and 60 seconds. This value must be to 60 seconds to be compliant with UL864 9 th

Edition. Default value is 60 seconds. (See the prefix of this manual for additional details).

AC Failure Report Delay

The AC Fail report delay time value can be set between 0 and 24 hours. Default value is one (1) hour. This value must be set between 1 and 3 hours to be compliant with

UL864 9 th

Edition. (See the prefix of this manual for additional details).

145

FireNET 4127 I & O Manual v1.90 UL

9.7.2.3 Configure Node: Network Interface

Up to 64 nodes (panels/network annunciators) can be networked together. The Network

Interface tab allows you to select the network events that a panel will respond to, and define the way in which it will respond. All the panels, except the one you are editing, will be shown in the list. To expand the responses to the event types, click on the [+] next to the panel you wish to edit. The properties of the node will expand, and you can select how the panel will respond to network events. The Network

Interface tab allows a given panel to have a unique profile that defines how it will respond to the rest of the nodes and event types on the network. Each network node can have a unique profile.

Types of node (panels/network annunciators):

Process

The process option instructs the node receiving a network event to behave exactly as it would if it were a local node event. For example, if a fire event activates, the panel would be expected to operate the NAC outputs and fire relays. Selecting the process option ensures that the panel does this from network fire events. If the process option was not selected, the panel would not process the event to actuate related inherent functionality…i.e. operate the NAC outputs or fire relays when a fire event is received from the network.

Display

The display option instructs the node receiving the network event to display the event on the LCD display exactly as it would if it were a local node event.

Log

This gives the option to store the network event in the local node event log. For example if a panel is designated as a master panel, it may be required that the panel logs all events on the network, whereas other panels log only their own events. Each node can store up to 500 events in the event log.

Print

This gives the option to print the network event. The node will then print both local events and network events assigned to it. It may be that a master panel is required to print all events (both local and network wide), while other panels print only local events.

Buzz

This gives the option to operate the node (panel/network annunciator) buzzer upon receipt of a network event.

146

FireNET 4127 I & O Manual v1.90 UL

Types of events:

• Fire - All Fire events

• Supervisory - All Supervisory events

• PreAlarm - All PreAlarm events

• Trouble - All Trouble events

• Disablements - All Disablement (bypass) events

• Auxiliary - All Auxiliary events

• Test - All Test modes occurring.

• Status - All Status events occurring.

9.7.2.4 Editing the number of Loops on a Panel

9.7.2.4.1 Editing using the Configure Node

1. Open the Configure Node of the panel you wish to edit. For instruction on how to edit the Configure Node, see section 9.7.2.

2. To change the number of loops in a panel, edit the settings on the Number of Loops.

If there are devices on a loop(s) you wish to delete, you must delete the loop devices first, then you can delete the loops themselves.

3. Click

to accept the changes, and exit from the window. Or click Cancel to cancel all changes, and exit from the window

9.7.3 Editing a FN-LCD-N Network LCD Annunciator

The Network Annunciator editable attributes are exactly the same as a panel except there are no SLC loops or NAC pattern properties to edit. The numbers of loops, loop offset, and NAC pattern options are grayed out.

See Section 9.7.2 for the proper method to access the Configure Node.

NOTE

9.7.4 Reserved for Future Use

147

FireNET 4127 I & O Manual v1.90 UL

9.7.5 Editing a Local Panel I/O

Editing the Local I/O is slightly different from editing a panel. It is not possible to delete the Panel I/O, however each of its inputs and outputs can be edited using appropriate Configure Input or Output windows.

Inputs Outputs

Trouble Input

Reset Input

Intermittent Input

Continuous Input

Silence Alarm Input

Notification Output 1

Notification Output 2

Notification Output 3

Notification Output 4

Supervisory Output (cannot be edited)

Input 1

Input 2

Auxiliary

Fire 1 Contact

Input 3 Fire 2 Contact

Fire Drill Input (cannot be edited) Fire Routing

Programmable Function Programmable Output

To learn more about the proper setting of Inputs, see section 9.9.2.1. For more information on the proper setting of Outputs, see section 9.9.2.2.

9.7.6 Removing a Panel

Deleting a component of your site is a simple process.

1. Just select the item you wish to delete the button in the toolbar or right click over the selected item and click the

Delete

option in the menu.

3. You will see this confirmation window when you delete a panel. Click Yes if you still want to delete it or click No to abort the deletion.

NOTE

: If you try to delete a panel when it still has devices attached to it, you will see an error message telling you to delete all of the devices attached to the Loops before attempting to delete the panel.

148

FireNET 4127 I & O Manual v1.90 UL

9.8 Configuring Option Boards/Serial LCD Annunciators on a Panel

9.8.1 Adding an Option Board/Serial LCD Annunciator

1. To add an Option Board, click on a panel in the Navigation tree where you want the module to be added.

2. Choose the icon representing the appropriate Option board in the Items pane or select the option from the right-click menu.

NOTE

: A maximum of 32 option boards may be added to a panel.

3. To add a FN-LCD-S Serial LCD Annunciator, click on the project level in the

Navigation tree and select the Serial Annunciator. Once this is selected, choose which panel (or node) that the Serial Annunciator will be added to.

NOTE

: A maximum of 15 FN-LCD-S Serial Annunciators may be added to a panel (or node).

9.8.1.1 Adding a SLC Board

An SLC Expander board adds an additional two Loops to a Hochiki 2 Loop Panel.

Follow the steps below to add an SLC expander to a 2 loop panel -

1. Open the Configure Node of the panel you wish to edit. For instructions on how to access the Configure Node, see section

9.7.2.

2. To add loops in a panel, change the

Number of Loops

from 2 Loops to 4 Loops

NOTE

: If you are deleting Loops, you must delete all devices attached to the Loops first

3. Click to accept the changes, and exit from the window. Or click Cancel to cancel all changes, and exit from the window

9.8.2 Editing an Option Board/Serial LCD Annunciator

To configure an Option Board/Serial LCD Annunciator, select the module you wish to configure, and select Edit from the toolbar or Edit Settings… from the right click menu.

149

FireNET 4127 I & O Manual v1.90 UL

9.8.2.1 Editing an I/O Board

Standard I/O Modules have 16 Channels, which can each be configured to be an input or an output. The default for all channels is set to inputs. After creation, you may not delete individual channels, only the entire module. By editing the settings of the existing module, you may change:

• the address

• inputs to an output or vice versa

To edit the settings of a channel, click on an existing I/O module channel in the Navigation tree and select Edit settings. These settings will either be for an input or an output.

Also by using the tabs labelled 1-8 and 9-16, it is possible to configure the location text and zones of all the channels, and clear all text and zone settings at once.

9.8.2.2 Editing a FN-LCD-S Serial LCD Annunciator

The Serial LCD Annunciator window has only two areas that require an individual to enter data:

• Serial LCD Annunciator Name

• Serial LCD Annunciator Address

NOTE

: A maximum of 15 FN-LCD-S Serial Annunciators may be added to a panel (or node).

9.8.3 Removing an Option Board/Serial LCD Annunciator

1. Select the Option board/Serial LCD

Annunciator you wish to delete.

2. Click on the Delete button in the menu or the delete button from the right-click button.

3. You will be given a confirmation window.

To complete the deletion, click the Yes button. To cancel, click the No button.

150

FireNET 4127 I & O Manual v1.90 UL

9.9 Configuring Panel I/O and Devices on a Loop

9.9.1 Adding a Device on a Loop

New devices can be added to the configuration in several different ways; using the main menus, toolbar, right click menu, or Items pane.

Click on a loop in the Navigation tree, then:

Click File, New, New Device, or

Click New on the toolbar, or

Right click over the loop in the Navigation tree, and click New Device.

Use the Items Pane to add a device.

Select a single device, by highlighting it, then select the Address using the drop down box, and choose a zone. Edit or add Location Text, this can be new text or previously entered, and click add. The device will have been added. Click on another device and add it, or click Close. You may edit the settings of the particular device after you have added it to the loop. You can also specify the number of devices to be added to allow multiple or “Block” device additions.

If you have reached the maximum number of devices on a loop, you will be prompted with a message that indicates you have reached the maximum addresses allowed.

NOTE

: The maximum number of addresses and sub-addresses possible per panel is

800. To check the current total address usage for any panel, right-click on the desired panel in the Navigation tree and select Edit Settings. In the lower right hand corner of

Configure Panel Settings screen, the total will be displayed.

9.9.2 Editing Panel I/O and Devices on a Loop

9.9.2.1 Editing Devices on a Loop

You may configure any device and all of its sub addresses using Loop Explorer. There are several ways to edit and configure a chosen device

To edit the settings of a device, click on the device you wish to configure in the

Navigation tree and select the edit settings option from the toolbar. You may also right click and select Edit Settings from the option menu, or double-click on the device itself.

The item you initially select from the Navigation tree or Device Table will determine the configuration window that will appear. For example, the configuration window options for an FRCME input module will be different than those of an SOM module.

151

FireNET 4127 I & O Manual v1.90 UL

9.9.2.2 Setting inputs (Panel I/O and Devices on a Loop)

The input settings window can be accessed by right-clicking on the Navigation tree input item, and clicking on Edit Settings...

After making the changes click OK to accept the settings, and exit from the window.

Or click Cancel to cancel all changes and exit from the window.

Options: Fire

Fire inputs activate outputs that are General Alarm mode in accordance with the rules of General Alarm mode. Control panel outputs will include the following:

• Common Fire LEDs

• Pulsing

• NAC

• Fire 1 Contact

• Fire 2 Contact

• Fire

Output

• Outputs (if flag set)

• LCD Fire Message, Address And Location Text Of Input

Options: Trouble

Trouble inputs activate any output configured as a trouble output. Trouble inputs will be annunciated by the control panel as follows:

• General Trouble LED

• Continuous

• Trouble

• Trouble Routing Output

• Outputs (if flag set)

• LCD Trouble Message, Address And Location Text Of Input

Options: Pre-Alarm

Sensors or inputs can generate a Pre-Alarm. This activates any outputs configured to respond to a pre-alarm. The control panel will respond as follows to a Pre-Alarm:

LED

• Continuous

• Outputs (if flag set)

• LCD Pre-Alarm Message, Address And Location Text Of Input

Options: Supervisory Alarm

Input modules, sensors and duct sensors can be configured to create a Supervisory alarm when activated. A Supervisory alarm will produce the following response by the panel:

Alarm

• Continuous

Contact

• Outputs (if flag set)

• LCD Supervisory Alarm Message, Address And Location Text Of Input

152

FireNET 4127 I & O Manual v1.90 UL

Options: Auxiliary

The Auxiliary action allows all sounder outputs to be activated from an input anywhere on the system when outputs have “Auxiliary” flag set with the following response at the panel:

Buzzer

• Outputs (if flag set)

• LCD Fire Auxiliary Message, Address And Location Text Of Input

Options: Silence

When a Silence input activates, it is as if the Alarm Silence button had been pressed at the panel.

Note

: A Silence Action will not latch. Therefore, input must be set to non-latching.

Options: Reset

Reset will be displayed on the LCD and recorded in the event log. When a reset input activates, it is as if the Reset button had been pressed at the panel.

Note

: A Reset Action will not latch. Therefore, input must be set to non-latching.

Options: Fire Drill

This option is not programmable for the onboard panel input. The Fire Drill button activates SOM and NAC alarm outputs that are programmed for General Alarm mode.

Panel relays are not activated during a Fire Drill.

Note

: A Fire Drill Action will not latch. Therefore, input must be set to non-latching.

Options: Transparent

A transparent input will have no effect on the panel. The only result of a transparent input is to control outputs via cause and effects configuration. The input activity will not be recorded in the event log.

Options: Disablement

Disablement inputs are used to disable a part or parts of the system via cause and effects configuration (normally for testing or maintenance purposes).

When an input designated as a disablement is operated, the panel will display the following:

• General Disablement Indicator

• Continuous Buzzer For 5 Seconds

• Address

(1-500)

• LCD Disablement Message, Address And Location Text Of Input

153

FireNET 4127 I & O Manual v1.90 UL

Options: Test

Inputs given the test mode attribute are used to activate a special type of cause and effect which enables the system to be placed in “Walk Test” Mode through a cause and effect action rather than from manually entering Walk Test Mode via the front panel menus.

When a test mode input is operated, the panel will execute the Cause and Effect action associated with it.

Input Latch

Input latch is used to “lock” an input into the ON state. Even if the input circuit restores to normal, the panel will still show the input to be ON. The input will remain latched unit a reset event occurs.

Note

: A latched input may not be set to reset type.

Output Delay: Bypass

When an input is operated with this attribute any outputs activated will bypass their delay time (if programmed) and switch on immediately. This attribute is useful if an input should respond immediately.

Input Delay

Input delay may be used to help prevent false alarms from inputs that fluctuate rapidly from alarm to normal state. The panel will not respond to the input until it has been activated for the programmed delay time. This feature is only available to “Non Fire” type inputs and other inputs allowed for delay per NFPA72/UL864. (Use of this feature may be subject to AHJ and other local requirements).

Action message

An Action message is the action related text displayed at the panel when the input is operated (i.e. Fire, Trouble etc). For some inputs, the message is user definable, such as a General Purpose input.

There are also nine user-defined messages that can be changed for specific use.

Zone

Each input can be assigned to a zone. It is useful to place inputs into zones if the output is required to respond in a zonal fashion, or is to be controlled by a cause and effect entry. Zones are also used to group devices into logical groups or per the building and code requirements.

Note

: Do not assign SLC loop outputs to zone 0.

154

FireNET 4127 I & O Manual v1.90 UL

Location Text

Each input can be given location text of up to 40 characters. As well as being useful in identifying devices and locations, the location text can be useful in identifying the device when compiling cause and effects programs.

9.9.2.3 Setting Outputs (Panel I/O and Devices on a Loop)

All outputs have a set of default attributes, which can be modified by using the edit window of an output. After making the changes, click OK to accept the settings and exit from the window. Or click Cancel to cancel all changes and exit from the window.

Below is a list of programming options for outputs:

Options: Gen. Alarm Mode (Common Fire Alarm)

Normally applicable to NAC outputs, Gen. Alarm Mode will turn the output on upon a fire condition as defined by the global General Alarm Mode set on the Configure Panel

Settings

window, or as set via the Edit Configuration menus on the panel. Other outputs can be assigned to General Alarm Mode as well when this flag is selected.

Options: Auxiliary

The output will operate upon any auxiliary event.

Options: Pre-Alarm Output

The output will operate upon any pre-alarm event.

Options: Supervisory Alarm

The output will operate upon any supervisory event.

Options: Trouble Output

The output will operate upon any trouble event.

Alarm Silence: Silenceable

Silenceable is normally applicable to NAC, SOM, ASB, & R2M outputs and ensures that the output turns off when the alarm is silenced (acknowledged) by the front panel pushbutton or operation of an input that is configured as silence alarm.

Delay: Stage one delay

Outputs can be delayed from 0 to 5 minutes in half-minute steps by changing the default delay of zero to the desired setting (on-board relays, routing outputs, R2M, and

DH98AR Relays only).

Delay: Stage two delay

If the output is Silenceable, the stage two delay option becomes available. The stage two delays gives additional time from 0 to 5 minutes in half-minute steps before the output operates after the alarm is acknowledged during the stage one delay period.

155

FireNET 4127 I & O Manual v1.90 UL

Strobe Output (NAC only)

The panel NAC circuits have an additional option called Strobe Output. If this option is selected, it will change the NAC circuit to a continuous output during alarm, regardless of the panel’s programmed output pattern. This allows for the connection of four-wire horn/strobes that require a Temporal or March pattern for the horn circuit, but a continuous pattern (steady) for the strobe circuit. It is also useful when driving strobe only circuits or speaker/strobe circuits when the audio power is being driven from a separate voice evacuation audio system, but the strobe power is being driven from the fire alarm system.

NAC Aux 24VDC (NAC only)

The panel NAC circuits have an additional option called “NAC Aux 24VDC”. By using this feature the NAC outputs can be alternatively programmed as an auxiliary power outputs rather than notification appliance circuits. This allows NAC outputs to function as 24VDC power outputs. Below is the list of power options:

• OFF – When set to this option, the NAC output functions as a standard NAC circuit and the Aux

24VDC options have no effect. This is the default setting.

• Continuous Power – When set to this option, the NAC output becomes a constant 24VDC output that always remains on.

• Door Holder Power – When set to this option, the NAC output releases when a fire event occurs or AC power is lost. The output returns after the panel is reset and the conditions are clear.

• Reset-able Power – When set to this option, the NAC output drops out upon panel reset and returns after 5 seconds. This is used for duct or 4-wire detectors that require power reset.

Zone

Each output can also be put into a zone as required. It is useful to put outputs into zones if the output is required to respond to general alarm mode or is to be controlled by a cause and effect entry. Zones are also used to group devices into logical groups or per the building and code requirements.

NOTE

: Do not assign SLC loop outputs to zone 0.

Location Text

Each output can be given location text of up to 40 characters. As well as being useful in identifying devices and locations, the location text can be useful in identifying the device when compiling cause and effects programs.

156

FireNET 4127 I & O Manual v1.90 UL

NOTE

: Panel Outputs can be programmed into three primary categories:

• Zone o When outputs are assigned to zones, the output operation can be triggered on a zoned basis. General alarm mode should be set to “zonal” for this operation.

• Programmable o When outputs are not assigned to general event categories via output attributes, the output operation is programmable by using Cause and Effect.

9.9.3 Changing a Device on a Loop

You may change a device type using Loop Explorer very easily. Click on the device you wish to change and either click on the toolbar option

Change or use the right click menu and select Change device type.

Changing is quicker than deleting and adding another device because it will keep the universal settings of all devices, such as Zone and

Location text.

9.9.4 Deleting a Device on a Loop

Deleting a component of your site is a simple process.

1. Just select the item you wish to delete

2. Click on the Delete button in the toolbar or right click over the selected item and click the Delete option in the menu.

3. You will see a confirmation window when you delete a device. It will have a list of all information that is attached to the device. Click Yes if you still want to delete it or click No to abort the deletion.

157

FireNET 4127 I & O Manual v1.90 UL

9.10 Loop Explorer Abilities

9.10.1 Reserved for Future Use

9.10.2 Cause & Effect Summary

The C&E Summary will show all cause and effect entries in the project, and the total number of inputs and outputs currently being used.

At the bottom of the window it will show you the totals for the Project, and how close to the maximum number of entries the Project is.

It is also possible to add Cause and Effects from the Summary, by clicking on the appropriate symbol. This will bring up the usual wizard, and from there you can view the input and output totals if a large number of Cause and Effects are going to be created. You may also copy a cause and effect, or delete it from here. Please see section 9.15 for more details on Cause and Effect programming.

9.10.3 Reserved for Future Use

9.10.4 Zone Manager

The Zone manager is a tool used for quickly viewing all panel and loop devices mapped to selected zones and for configuring them to particular zones.

Access the Zone manager by using the toolbar or the Edit menu.

The List on the left shows Zones 0 - 500, the highlighted icons contain items, where the shaded ones do not.

Select a Panel to start viewing the contents of the selected zone from the list on the left.

Select one or more items - to select multiple items hold Ctrl or Shift on the keyboard and click on the desired items. Next drag and drop them onto a new zone from the list of zones. This will remove the icon from the view on the right, as they have been moved to the new zone.

The Alarm Verification Feature is also enabled from this menu on a per zone basis. To enable Alarm Verification operation, you must select the “Verify” check box for that zone. Alarm Verification only applies to photo and ion smoke sensors in that zone.

For more information on using Zones, see section 9.13.

9.10.5 Reserved for Future Use

158

FireNET 4127 I & O Manual v1.90 UL

9.11 Loop Explorer Networking

9.11.1 Getting it working

With all network cards allocated a unique address and all nodes (panels & network annunciators) connected as described in Section 6, it is now possible to get the panels communicating with each other by doing an AUTOLEARN at each one. In this default configuration all panels will respond to the default network settings. Default network settings are to process, display, log, print and operate the panel buzzer for all network events (except status events) from all other panels. This is fine for initial testing and getting the network talking, but may need to be updated to suit the specific project needs.

9.11.2 Using the Loop Explorer PC configuration

To enable selection of which panels respond to which events it is necessary to configure panels using the Loop Explorer configuration program.

Loop Explorer allows extensive configuration of the system and the details of this are contained within the program help files and elsewhere in this manual. See section

9.7.2.3 for programming network attributes in Configure Panel Settings. For the purposes of this section, only network processing and event details are discussed.

There are five options for each network event type as to how it will be handled by the recipient node:

Process

The process option instructs the panel receiving a network event to inherently operate exactly as it would if it were a local panel event. For example, if a fire event activates, the panel would be expected to operate the NAC outputs and fire relays as programmed. Selecting the process option ensures that the network panel does this. If the process option were not selected, the panel would not operate the NAC outputs and fire relays as programmed.

Display

The display option instructs the panel receiving the network event to display the event exactly as it would be displayed if it were a local panel event.

Log

This gives the option to store the network event in the event log. For example if a panel is designated as a master panel, it may be required that the master panel logs all events on the network whereas other panels log only their own local events.

Print

This gives the option to print the network event. It may be that a master panel is required to print all events and that other panels print only local events.

Buzz

This gives the option to operate the panel buzzer upon a network event from other panels.

159

FireNET 4127 I & O Manual v1.90 UL

The ease and versatility of programming the network interface ensures that changing site requirements can be swiftly accommodated with a minimum of effort. A brief description of all network event types is listed below:

9.11.3 Fire action

Being a fire control panel, the fire action will probably be the most widely used and a fire input will be announced by the following:

• COMMON

BUZZER

OUTPUTS

• FIRE 1 CONTACT

• FIRE 2 CONTACT

• FIRE ROUTING OUTPUT

• LCD FIRE MESSAGE, ADDRESS AND LOCATION TEXT OF INPUT

9.11.4 Auxiliary action

The Auxiliary action allows outputs to be activated from an input anywhere on the system with the Auxiliary flag set with the following response at the panel:

BUZZER

OUTPUTS

• LCD

OF INPUT

9.11.5 Pre-alarm action

Sensors or inputs can generate a pre-alarm. The control panel will respond as follows to a pre-alarm:

• PRE-ALARM

BUZZER

• LCD PRE-ALARM MESSAGE, ADDRESS AND LOCATION TEXT OF

INPUT

9.11.6 Trouble action

Inputs attributed the trouble action, or panel trouble events such as AC Failure, will be announced by the control panel as follows:

• GENERAL TROUBLE LED

• CONTINUOUS BUZZER

• TROUBLE

CONTACT

• TROUBLE ROUTING OUTPUT

• LCD TROUBLE MESSAGE, ADDRESS AND LOCATION TEXT OF

INPUT OR EVENT

160

FireNET 4127 I & O Manual v1.90 UL

9.11.7 Disablement action

Disablement inputs are used to disable a part or parts of the system via cause and effects configuration (normally for testing or maintenance purposes). When an input designated as a disablement is operated, the panel will respond as follows:

• POINT BYPASSED INDICATOR LED

BUZZER

• CAUSE AND EFFECT ACTION

• LCD DISABLEMENT MESSAGE, ADDRESS AND LOCATION TEXT OF

INPUT

• GENERAL TROUBLE LED

9.11.8 Supervisory Alarm action

Supervisory Alarm input is available which produces the following response by the panel:

• SUPERVISORY ALARM LED

• CONTINUOUS

• LCD SUPERVISORY ALARM MESSAGE, ADDRESS AND LOCATION

TEXT OF INPUT

• SUPERVISORY RELAY

9.11.9 Test action

Inputs given the test mode attribute activate a special type of cause and effect which enables the system to be placed in Walk Test Mode without having to manually invoke the Walk Test Mode through the front panel controls and menus. When a test mode input is operated, the panel will respond as follows:

• ON TEST LED

• LCD ON TEST MESSAGE

• CAUSE AND EFFECT ACTION

• GENERAL TROUBLE LED

9.11.10 Status

If the Process Status event is enabled, then pressing Alarm Silence, Re-sound Alarm, and Reset controls from that panel will cause the same response on the selected panel as if the local buttons have been pressed. This allows panel controls to be sent over the network to other panels. Therefore if a panel is set to Process / Display a fire event from another panel, the local outputs cannot be silenced, resounded, or reset by that panel unless the Process Status event is set. The Display Status event allows the local panel to show Status events from other panels (Initializing etc). However, these events cannot be processed, as there is not a process associated with them.

• INITIALIZING A DEVICE

• INITIALIZING A PANEL

• AUTOLEARNING A PANEL

• RE-CONFIGURE

• SILENCE

• RESOUND

• RESET

161

FireNET 4127 I & O Manual v1.90 UL

9.11.10.0 Network Trouble Messages

While commissioning a networked system there are various trouble messages which may appear. Listed below are the messages, which may appear, and a brief description of what they mean.

9.11.10.1 Network open or short circuit trouble

This is quite self explanatory and indicates a cabling trouble between two nodes.

However, by observing the green and red LEDs on the network card it is possible to see whether the trouble is on the upper two terminals of the network connector

(incoming) or the lower two (outgoing). If the red LED is off then the trouble is on the cable connected to the upper two terminals and if the green LED is off the trouble is on the lower two terminals. Thus, if there are two panels with network LEDs not lit (a red on one and a green on the other) the trouble can be identified as between those two panels.

9.11.10.2 Unexpected network card

Should a network card be installed in a control panel that is already configured and working, the panel does not expect to have a network card installed, therefore this trouble message will appear. The panel must be re-configured by Autolearn or Loop

Explorer to enable it to expect a network card.

9.11.10.3 Unexpected network node

If a new network panel is connected to an already working network, the rest of the network will not expect to see an additional node and will announce this trouble.

The unexpected network panel will respond to network events as per the default configuration and all other panels will respond to events from the new network panel as per the default configuration. All panels must be configured to see the total number of panels connected to the overall panel network by using Loop Explorer or by Autolearn.

9.11.10.4 Network node missing

This message will be displayed on all panels if a network node they are expecting to communicate with does not answer within approximately 100 seconds. This may occur if a control panel loses all power or if both the in and out network connections are disconnected from the panel.

9.11.10.5 Network card not installed

If a control panel is configured to be part of a network by Autolearn or Loop Explorer, and a network card is not installed, the panel will display this message.

162

FireNET 4127 I & O Manual v1.90 UL

9.11.10.6 Network card address incorrect

Once a panel is configured to expect a network card to be present it will also know which address (set on the network card DIP switch) to expect. If it detects that a card is installed but the address does not match the one expected, then this trouble message will be displayed. If the address of a network card must be changed then this should be done with both the AC and battery backup power off. Once the address is set and the panel is powered up, the panel must be re-programmed to see the new address via

Autolearn or Loop Explorer software.

9.11.10.7 Network comms trouble

Highly sophisticated error checking and filtering is used in the FireNET network protocol. It is possible under extreme conditions for data packets to become corrupted and not be received by a panel. In these circumstances this trouble message will be displayed. This indicates a very degraded transmission path and occurrence of this trouble should be investigated. Possible causes are cable lengths greater than those specified, cable specification other than that specified or high levels of electromagnetic interference.

9.11.10.8 Unknown network type

As the FireNET product line is updated and newer versions of software, firmware, and hardware are released, when a network object detects other network objects with differing versions, this trouble message will be displayed. This mechanism has been put in place to enable a control panel to identify a network object with a differing version than its own.

9.11.10.9 Unspecified network event

The development of the FireNET system is ongoing and new features and functionality will be added from time to time. This mechanism has been put in place to enable a control panel to identify a new or unknown network event type differing than its own.

163

FireNET 4127 I & O Manual v1.90 UL

9.12 Loop Explorer Networking - Keeping a record

When a network has been configured, the configuration data file keeps a record of the configuration that can be copied into other documents as shown in the example below by using the Print/Pre View feature.

FIRENET NETWORK CONFIGURATION

D:\Storage\storage\Laptop_Sync_Folder\FireNet-4127_Software\Project Files\HC_Seminar_Example1.hsa

02/07/2005 15:03

Panel - Facp #1

Panel Text Hochiki Analog/Addressable Panel 1

Network Address 1

Default Pattern Temporal

First Node Address 0

Last Node Address 0

Access 2 Code

Access 3 Code

22222

33333

Number of Loops 2

Number of Zones 500

Calibration Time 07:00

Day of week Start End

Sunday

Monday

08:00 18:00

Tuesday 08:00 18:00

Wednesday 08:00

Thursday 08:00

Friday

18:00

08:00 18:00

Saturday 08:00

FireNET 4127 I & O Manual 164 v1.90 UL

Facp #1 - Network Interface

Panel Fire Aux. Pre Al Trouble Disab. Superv. Test Status

02 - Facp #2

Process Yes Yes Yes Yes Yes Yes Yes Yes No

Display Yes Yes Yes Yes Yes Yes Yes Yes No

Log

Yes Yes Yes Yes

Yes Yes Yes Yes No

Buzz Yes Yes Yes Yes No

03 - LCD Annun #3

Process Yes Yes Yes Yes Yes Yes Yes Yes No

Display Yes Yes Yes Yes Yes Yes Yes Yes No

Log

Yes Yes Yes Yes Yes Yes Yes Yes No

Buzz Yes Yes Yes Yes No

Facp #1 - Loop 1 (3 Devices)

Device Name

001.00

002.00

003.00

ALG-V

ATG-EA

AIE-EA

Facp #1 - Loop 2 (0 Devices)

Sensor 01

Sensor 02

Sensor 03

Facp #1 - Local I/O

I/O

Trouble Input Input 00

Reset Input Input 00

Intermittent Input Input 00

Continuous Input Input 00

Silence Alarm Input Input 00

Input 1

Input 2

Input 00

Input 3 Input 00

Fire Drill Input Input 00

Fire

Trouble 00

Reset 00

Auxiliary 00

Silence 00

Transparent 00

Fire Drill 00

D2.50 N2.50

D135 N135

D-Hi N-Nrm

Notification Output 1 Output 01

Notification Output 2 Output 01

Notification Output 4 Output 05

0.00

MS 0.00 0.00

165

FireNET 4127 I & O Manual v1.90 UL

1st Floor Lobby Smoke Detector

Electrical Room Heat Sensor

3rd Floor Kitchen Ion Sensor

Strobe Output 1st Floor

Bell/Horn Output 1st Floor

Bell/Horn Output 5th Floor

C&E controlled NAC output - Special

Output

Auxiliary Output 00

Fire 1 Contact Output 00

Fire 2 Contact Output 00

Fire Routing Output 00

Programmable

Contact

Trouble

Out.

EMS

Panel - Facp #2

Panel Text Hochiki Analog/Addressable Panel 2

Network Address 2

Default Pattern Temporal

First Node Address 0

Last Node Address 0

Access 2 Code

Access 3 Code

22222

33333

Number of Loops 2

Number of Zones 500

Calibration Time 07:00

Day of week

Sunday

Monday

Tuesday

18:00

Thursday 08:00

Friday

Start End

08:00 18:00

Wednesday 08:00

18:00

08:00 18:00

0.00

Facp #2 - Network Interface

Panel Fire Aux. Pre Al Trouble Disab. Superv. Test Status

01 - Facp #1

Process No No No No No No No No Yes

Display No No No No No No No No Yes

Log No No No No No No No No Yes

Print No No No No Yes

Buzz No No No No Yes

166

FireNET 4127 I & O Manual v1.90 UL

03 - LCD Annun #3

Process No No No No No No No No Yes

Display No No No No No No No No Yes

Log

No No

Buzz No No No No Yes

Facp #2 - Loop 3 (6 Devices)

No No No No No No Yes

No No No No No No No No Yes

Device

001.00

001.01

002.00

003.00

003.01

003.02

004.00

005.00

SOM

FRCME

R2M

CZM

DIMM

Common 01

Output 01

Input

Common 13

Output 13

Common 13

LB Fire

0.00

Fire

1st Delay

0.00

2nd Delay

0.00

Text

SOM Module

SOM Bell Output 1st Floor

1st Floor Lobby Pullstations

R2M Module

Relay 1: Elevator recall

005.01

005.02

006.00

DIMM

FRCME

Facp #2 - Loop 4 (0 Devices)

Facp #2 - Local I/O

Input 13

Input 05

Type

Trouble Input Input 00

Reset Input Input 00

Reset

Fire

Supervisory Al

Fire

Trouble 00

3rd Floor Conventional Devices

DIMM Module

Waterflow Switch PIV#1

Valve Position Tamper PIV#1

5th Floor Lobby Pullstations

Intermittent Input Input 00

Continuous Input Input 00

Silence Alarm Input Input 00

Input 1

Input 2

Input 3

Fire Drill Input

Input 00

Auxiliary 00

Silence 00

Test Mode 00

Disablement 00

Transparent 00

Fire Drill 00

Transparent 00

Input to Start Walk Test Script

Input to Start Disablement Script

Output

Notification

Output

Supervisory

167

FireNET 4127 I & O Manual v1.90 UL

Auxiliary Output 00

Fire 1 Contact Output 00

Fire 2 Contact Output 00

Fire Routing Output 00

Out.

Trouble Contact Output 00

Trouble Routing Output 00

EMS

0.00

Facp #2 - I/O Module 32 - 32

Channel Type Zone Flags Action

Channel 01 Input 00

Channel 02 Input 00

Channel 03 Input 00

Channel 04 Input 00

Channel 05 Input 00

Channel 06 Input 00

1st Delay

Trouble 00

0.00

2nd Delay

Channel 07 Input 00

Channel 08 Input 00

Trouble 00

0.00

Text

Panel - LCD Annun #3

Panel Text Shinagawa Hotel Project LCD #3

Network Address 3

First Node Address 0

Last Node Address 0

Access 2 Code

Access 3 Code

22222

33333

Number of Loops 0

Number of Zones 500

168

FireNET 4127 I & O Manual v1.90 UL

LCD Annun #3 - Network Interface

Panel Fire Aux. Pre Al Trouble Disab. Superv. Test Status

01 - Facp #1

Process Yes Yes Yes Yes Yes Yes Yes Yes No

Display Yes Yes Yes Yes Yes Yes Yes Yes No

Log

Yes Yes Yes Yes Yes Yes Yes Yes No

Buzz Yes Yes Yes Yes No

02 - Facp #2

Process Yes Yes Yes Yes Yes Yes Yes Yes No

Display Yes Yes Yes Yes Yes Yes Yes Yes No

Log

Yes Yes Yes Yes Yes Yes Yes Yes No

Buzz Yes Yes Yes Yes No

LCD Annun #3 - Local I/O

I/O

Fire Drill Input Input 00

Input 00

Fire Drill 00

Transparent 00

Output

Auxiliary Output 00

Fire 2 Contact Output 00 EMS

Trouble

Action : Air Handler Shutdown Logic for Zone 10

Cause (OR)

0.00

Facp #1 - Loop 1 Address 001.00

Facp #1 - Input 1

Facp #2 - I/O Module 32 32 - Channel 04

Zone 10

Effect (Temporal)

Facp #2 - Loop 1 Address 003.02

Facp #2 - I/O Module 32 32 - Channel 12

Zone

Action : Fire Pump Startup Logic from Waterflow

Cause (OR)

Facp #2 - Loop 1 Address 005.01

Effect (Temporal)

0.00

169

FireNET 4127 I & O Manual v1.90 UL

Facp #1 - Programmable output

Facp #2 - I/O Module 32 32 - Channel 16

Zone

Disablement : Disable Script Lobby & 1st Floor

Cause (OR)

Facp #2 - Input 2

Effect (Disablement)

Facp #1 - Loop 1 Address 001.00

Facp #2 - Loop 1 Address 002.00

Facp #2 - Loop 1 Address 001.01

Facp #1 - Notification Output 1

Facp #1 - Notification Output 2

Facp #2 - I/O Module 32 32 - Channel 03

Facp #2 - I/O Module 32 32 - Channel 11

Facp #2 - Loop 4

Test Mode : Walk Test Script Zones 3, 6, 10, 13

Cause (OR)

Facp #2 - Input 1

Effect - (Test)

Sounders:

Zone

Audible

Zone

Flags -

M = General Alarm

P = Pre Alarm

D = Day mode N = Night Mode

S = Silenceable

R = Resetable

L = Latching

O = Delayed Output

F = Trouble

A = PreAlarm Output

B = Output Delay Bypass

170

FireNET 4127 I & O Manual v1.90 UL

9.13 Loop Explorer Networking - Using zones

The use of zones on a FireNET network is an important issue and employs a philosophy that may be unfamiliar to some. This page has been included to highlight the importance of understanding how zones are used on this system and should be fully understood before system design is started. Unlike some other networked systems, zones on the FireNET system are network wide.

This means that for example, device number 1 on loop 1 of panel 1 can be in the same zone as device number 126 on loop 4 of panel 64 and so on. This gives the system great flexibility where zones need to be shared across panels such as risers or elevator shafts but this philosophy must be understood from the outset to enable a system design to be implemented effectively.

The system can have up to 500 zones and any device or input, on any panel, can be placed in any zone. Identification of the alarm is by a unique address in the form: -

Event type, Device type, Zone, Address, Loop, Panel name, Location text.

NOTE

: Do not use Zone 0 for field devices. This is the panel’s internal master zone.

System designers must be aware however that the entire system can only have one zone 1, one zone 2 etc. On smaller systems where the numbers of zones is likely to be much less than 500, spare zones can be used to good effect to simplify network wide cause and effects by using zones as groups and operating upon these rather than individual devices to achieve the required functionality.

See Section 9.10.4 for additional details regarding programming zones.

171

FireNET 4127 I & O Manual v1.90 UL

9.14 Loop Explorer Options

9.14.1 COM Port

On some computers, it may be necessary to change the communications port used to transfer data to and from the panel.

The default is COM 1. Click File, Options. Select the COM port you wish to use. See section

9.4.2 for exact details on how to set COM ports.

9.14.2 Default Project Folder/ Memory Management

The default project folder is the initial folder location offered for opening and saving Loop

Explorer projects. To modify the folder location, click File, Options, then click the MISC tab.

Either type the path in or click Find, if you wish to change the folder location. Select the folder using the browser window, then click OK to continue, and click OK in the original screen, or click cancel to exit the window.

It is also possible from this screen to set the computer’s RAM available to Loop Explorer. Be sure not to set this value larger than the computer’s physical RAM memory size.

Under the Options/Misc screen it is possible to make Loop Explorer use less of the computer’s RAM for use on older computer’s with less RAM to utilize.

The default will be set to medium, 32MB – 128 MB RAM installed which most computers have. If the computer is an older computer, using Windows 98, it may have a small amount of RAM to use, as Windows takes a lot by itself just to load. Upon changing the amount

Loop Explorer has to use, the program will have to be closed and opened again, in order to free up the memory. If Loop Explorer is set to having Low RAM, you may only add up to approximately 12 panels, full of devices. If it is set to Medium, it may hold about 32 panels, and high, will be all 64. When a project file (*.hsa) is first opened, the Quick Load option allows use of less RAM memory such that more panels are possible and the initial Loop

Explorer start-up time may be reduced. If any problems are experienced using Loop

Explorer, such as illegal operations or the system running low on resources, setting the

RAM usage to Low may help as well.

9.14.3 Splash Screen

The splash screen is a bitmap image file (.BMP), which is displayed when Loop Explorer initially starts. The default splash screen may not be altered, but you have the option to turn the default splash screen off. A custom splash screen may be used in place of default one.

A custom splash screen can only be a file up to 2Mb in size, so as not to increase the loading time of the application.

172

FireNET 4127 I & O Manual v1.90 UL

9.14.4 Other

Within this screen it is possible to set whether Loop Explorer loads Location text in the

Cause and Effect Action wizard. This is because this may be a lengthy operation for some computers, and may take some time to load the wizard, if its a slow computer with a large site.

The Autosave feature is also enabled within this screen. Once enabled, you may also set the time interval in which the Autosave occurs.

173

FireNET 4127 I & O Manual v1.90 UL

9.15 Cause and Effect Programming

9.15.1 Cause & Effect Types

Cause and Effect programming allows you to link an input or group of inputs to an output or group of outputs. Cause and Effect is a powerful feature of the FireNET system, and is very flexible, allowing for very creative input and output mapping.

There are three basic types of C&E:

1. Action

2. Test Mode

3. Disablement

An Action type C&E will create some sort of action output in response to an input activation. One example of an Action C&E is a relay that follows the state of an input. A common application might be relays for elevator recall, door release functions, or damper control.

A Test Mode type C&E allows you to create an input (with an Action of Test) that puts a zone or zones into Test Mode. This is very similar to the panel’s ‘Test Zones’ feature, but is not subject to the same 15-minute time out (see section 10.1).

A Disablement type C&E allows you to create an input (with an Action of Disablement) that disables devices or loops or zones on a panel or panels.

All C&E types are created using OR, AND, or Coincidence logic.

To create a new C&E, select Cause and Effect on the Navigator Pane. You may then rightclick and select New Cause and Effect from the right-click menu, or select New on the

Toolbar. You may also double-click or drag and drop the type of C&E you wish to build from the Items Pane to the Device Table. Any of these actions will open the Cause and

Effect Wizard.

First you must select the “Cause”, the event that will stimulate the output. This could be a smoke sensor in an elevator lobby. It could be an analog duct detector. It can be any input on the system, including an entire zone. Notice across the top of the window that you may select from Loop Inputs, I/O Channel Inputs, Fire Zone Inputs, and Panel Inputs. These may be selected in any number and combination. Notice too that all inputs from all panels are available to you. This means that your C&E statements can operate across the network on any or all panels!

You must also choose an Action Operator for a C&E. There are three types of action operators:

• AND/All

• OR/Single

Two

174

FireNET 4127 I & O Manual v1.90 UL

AND logic

states that all inputs must be activated before the programmed output(s) will take place (input 1 AND input 2 AND input 3, etc.)

OR logic

is also called Single, since a single input is all that is required to activate the desired output(s) (input 1 OR input 2 OR input 3, etc.)

Coincidence/Any Two logic

says that any two inputs can activate the desired output(s), it does not matter which two it is.

After the ‘Cause’ has been selected along with the appropriate Action Operator, click on the

Next button. This will move you to the ‘Effect’ screen, where you will select the output(s) that will be activated by this C&E. Depending on the type of C&E you are creating (Action,

Test Mode or Disablement) you will see different things. For example:

• An

will display Loop, I/O, Zone and Panel outputs that you may select. In addition, you must select the Output Type; Temporal, Continuous or

March. The Output Type only applies to NAC circuits and SOM/ASB devices, as relays do not follow Temporal or March activation patterns.

NOTE

: To activate an SOM module using a C&E, you must choose the zone that the SOM is assigned to. To do this, simply select Zone Outputs and check the zone box that the SOM is assigned to. Remember, older version SOM (v2.0 or earlier) are limited to zones 1-253. In later release

SOM and FireNET, the upper zones will be supported.

Test Mode type C&E

will display all 500 Zones – you may select one or more of them at this point. You must also choose the Test Type, either Silent or Audible.

This selection determines if the notification circuits will momentarily activate to confirm that an input has been tested.

• A

will display all items that can be disabled, including loops, zones and devices. You may choose one or more items that will be disabled when the C&E executes.

After you have selected the ‘Effect’, click on the Next button. You may now assign a name to your C&E. The name can be up to 40 characters long, including spaces. It is important to be as descriptive as possible when naming your C&E, particularly if your project has a lot of them.

When building C&E entries, remember that panel and loop outputs can be programmed to activate from various events.

NOTE

: If you want an output to activate ONLY from a C&E, be sure that General

Alarm and all other options are not selected in the Output’s Properties.

Otherwise your output may activate at unexpected times.

175

FireNET 4127 I & O Manual v1.90 UL

9.15.2 Cause & Effect Examples

To assist you in building C&E entries, some examples are provided below. Please note that these examples are given for instructional purposes only, and are not intended to be used for your actual application! In some cases, local code or other restrictions may apply.

When in doubt, check with the Authority Having Jurisdiction for your project.

Example #1 “Action” Type C&E

A four-story building with a single elevator needs two outputs to be used for elevator recall. The first-floor smoke detector in the elevator lobby will be used to recall the elevator to the alternate floor. The elevator lobby smoke detectors on floors 2 – 4 will be used for primary recall to the first floor (this example does not consider elevator machine room or shaft detectors, etc. If needed, they can simply be added to the appropriate C&E).

This application will require two C&Es to be created – one for Primary recall, and a second one for Alternate Recall. In our example one R2M module will be used to provide both outputs. To keep things simple, the smoke detector on the first floor is installed at loop 1, address 1. The second floor is address 2, third floor is 3 and fourth floor is 4. The R2M is at address 5, outputs are 5.01 and 5.02.

Both C&Es will be an Action type. For the first one, select address 1 (first floor elevator lobby smoke) as the ‘Cause’, with an Action Operator of OR. Click on Next, and select the ‘Effect’, the R2M output at 5.01. Click on Next, name the C&E

‘Alternate Elevator Recall’ and click Finish. This will link the first floor smoke detector to R2M 5.01, which can then be used to recall the elevator to the alternate floor in the event of a fire in the first floor elevator lobby.

Next, create the second Action C&E. Select addresses 2-4, with an Action Operator of OR (we want the elevator to recall on a single activation). Click Next, and select

R2M 5.02. Click Next, name it ‘Primary Elevator Recall’ and click Finish.

The last thing to check is the Output Properties of the R2M relays. Be sure that

General alarm and other output attributes are NOT checked.

System operation will be as follows – during a fire alarm, the panel will respond as it normally does, but the R2M at address 5 will do nothing UNLESS the alarm comes from one of the smoke detectors used in the C&E statement. In this case the panel will respond normally but one of the R2M relays will activate too.

176

FireNET 4127 I & O Manual v1.90 UL

Example #2 “Test Mode” type C&E with AND logic

One of your FireNET installations is at a very large school, and they want to test the system on a monthly basis. This testing must be done outside of school hours, and since it requires access to locked classrooms, the school maintenance personnel have decided to do the testing themselves. They do have one request though – a set of security keyswitches that, when activated, will put the panel into Test Mode.

This feature will require that both of them be present in order to test the system.

In order to set this up, you must program 2 panel or loop inputs with an Action of

Test. Now, begin a Test Mode C&E. You will notice that only devices or inputs with an Action of Test will be displayed on the ‘Cause’ screen. Select both of the inputs and select AND as the Action Operator. Click Next to continue. Select all zones that must be included in the testing. If audible feedback is desired during the testing, select Audible. If not, select Silent, then click Next. Select a descriptive name for the

C&E and click Finish.

Here is how it will work – The panel will recognize if any one of the inputs is activated, but will do nothing until BOTH of them are activated. At this time, the C&E will execute, and all selected zones will be put into Test Mode. The Test Mode will remain active until one (or both) keys are turned off.

Example #3 “Disablement” type C&E

False alarms from smoke detectors in a commercial laundry have led to a request to be able to disable smoke detectors during working hours. The manager wants to use the Programmable Function button on the front panel to do this.

First you must edit the Programmable Function button and change the Action to

Disablement. Also, be sure that Latching is selected. Now, begin a new

Disablement-type Cause and Effect. Select the Programmable Function button from the Panel Inputs list, and select an Action Operator of OR/Single. Click Next, and select all of the smoke detectors that need to be disabled. Click Next, then name the

C&E…that’s it.

Here’s how it will work – the manager pushes the Programmable Function button from the Access Level 2 menu, which disables the smoke detectors. At the end of the day, the panel is reset and the disablement clears immediately. This option allows the manager to disable many detectors with relatively few key presses at the panel.

As you can see from these examples, FireNET’s Cause and Effect statements open up many possibilities.

177

FireNET 4127 I & O Manual v1.90 UL

Section 10 - Testing and Troubleshooting

10.1 One Man Walk Test - TEST ZONES

The one-man walk test feature is intended to allow a single service person the ability to test each device without having to reset the panel each time a device is activated. While in test mode, the panel will automatically reset after 3 seconds following any device activation.

This allows a service person to activate a device, verify the panel responds by sounding the audible and visual notification appliances, then move on to the next device without going back to the main panel to reset. The Test Zone feature will only activate outputs & devices that are assigned to General Alarm Mode based on the options enabled as described below.

One-man walk test mode is implemented by selecting the TEST ZONES option from the

Access Level 2 Main Menu.

Follow these steps to implement a one-man walk test using the TEST ZONES option:

1. Enter Access Level 2 operating mode as described in Section 7.3.1

2. Press the right navigational arrow key to access the Main Menu.

3. Scroll down to highlight the TEST ZONES option.

4. Press the right arrow key to select TEST ZONES.

5. From the Test Zones Menu use the up/down arrow keys to select which zone to test.

6. Press the right navigational arrow key to display the test options.

Local NAC ON - OFF

Use the up/down arrow keys to select ON or OFF. Setting this option to ON will make all of the audible and visual notification circuits (NAC 1-4) activate for the 3-second duration of each device tested. Setting this option to OFF disables the audible and visual notification appliance outputs during test mode.

Panel Outputs ON-OFF

Use the up/down arrow keys to select ON or OFF. Setting this option to ON will make all panel relay and voltage outputs function as they have been configured. Setting this option to OFF disables the panel relay and voltage outputs during test mode.

Loop Outputs ON-OFF

Use the up/down arrow keys to select ON or OFF. Setting this option to ON will activate

SLC loop output devices such as SOM modules for audible and visual devices, but will not activate R2M modules. Turning this option to OFF disables the SOM modules during test mode.

178

FireNET 4127 I & O Manual v1.90 UL

Once the test options have been set press “Enter” to start the test or “Exit” to cancel. If you start test mode and want to cancel it anytime within the 15-minute test period, enter

Access Level 2 and navigate to TEST ZONES. Enter TEST ZONES and use the right arrow key then Enter to toggle test mode to off.

When a zone is placed into test mode a 15-minute timer is started. If the 15-minute timer expires with no testing done, the test is automatically terminated and the panel is placed back into normal operation. The 15-minute timer is re-started each time a device is tested.

NOTE

The FN-4127 will be placed in a trouble condition during test mode. The “ON

TEST” LED will also illuminate.

10.2 View / Print Event Log

The View Print Event Log menu command allows the user to view the systems 500-event memory log. Any condition outside of normal operation of the system generates an entry into the event log. The event log is very useful tool for troubleshooting system problems or verifying certain activities such as Fire Drills actually took place.

ACCESS LEVEL 3 MENU

EDIT CONFIGURATION

SET TIMES

►VIEW PRINT EVENT LOG

PRINT CONFIGURATION

SYSTEM DISABLEMENTS

LOOP DATA TEST

10.2.1 View Event Log

To view the event log, you must first enter Access Level 3 (see section 8.1.1). Once in

Access Log 3, select VIEW PRINT EVENT LOG. Then select “View Event Log”.

VIEW/PRINT EVENT LOG MENU

► View Event Log

Print Event Log

Clear Event Log

179

FireNET 4127 I & O Manual v1.90 UL

Then select the Event Type Option:

SELECT EVENT TYPES TO VIEW

Fire - 4

Pre-Alarm - 0

► Trouble - 120

Disablements - 0

Other Events - 94

All Events - 218

Then select the Individual Events as needed:

VIEW TROUBLE EVENTS 120/120

* TROUBLE:SOM ZONE 02 *

ADR=012.00 LOOP=2 ND=1 AUTOLEARN

TIME 14:35 05/08/2003

Disconnected trouble Cleared

Use UP/DOWN arrow keys to scroll events

10.2.2 Print Event Log

To print the event log, you must enter Access Level 3 as noted above (see section 8.1.1).

Once in Access Level 3, select VIEW PRINT EVENT LOG. Then select the “Print Event

Log”.

VIEW/PRINT EVENT LOG MENU

View Event Log

► Print Event Log

Clear Event Log

Then select the Event Type Option

SELECT EVENT TYPES TO PRINT

► Fire - 4

Pre-Alarm - 0

Trouble - 120

Disablements - 0

Other Events - 94

All Events - 218

Then press the Enter key to start printing those event types.

180

FireNET 4127 I & O Manual v1.90 UL

PRINT FIRE EVENTS

Press ENTER to start print.

Press EXIT to quit

Press < to go back.

See Section 3.7 for information on adding a printer to the FireNET panel.

10.2.3 Clear Event Log

To clear the event log, you must enter Access Level 3 as noted above (see section 8.1.1).

Once in Access Level 3, select VIEW PRINT EVENT LOG. Then select the “Clear Event

Log”.

VIEW/PRINT EVENT LOG MENU

View Event Log

Print Event Log

► Clear Event Log

Then press the Enter key to clear the Event Log, or EXIT to cancel.

CLEAR EVENT LOG MENU

Event Log has 218 entries

Press ENTER to clear Event Log.

Press EXIT to quit

Press < to go back.

181

FireNET 4127 I & O Manual v1.90 UL

10.3 Loop Data Test

To start the Loop Data Test function, you must first enter Access Level 3 as noted above

(see section 8.1.1). Once in Access Level 3, you then must select the Loop Data Test option.

The Loop Data Test Function is a troubleshooting tool that is most cases will never be necessary. When the time does come at that problem job site, the Loop Data Test Function can be easily activated to monitor communication between the FireNET and loop devices.

This tool displays the time and date of the test activation, the number of successful and unsuccessful communications on the loop, and the current date and time. The Loop Data

Test Function runs in the background and has no affect on the FireNET’s ability to perform its intended functions of detection, notification, and control. It is therefore possible to start a

Loop Test during a normal business day and let it monitor an individual loop overnight, over a weekend, or during the week. The maximum number of readings is 9,999,999. This will allow a loop to be monitored in excess of one week.

In the event that a large number of bad data readings are received, a review of the installation conditions must be conducted. Possible sources of communications problems are bad wiring, poor wiring practices, large sources of electrical noise (large machines, radio transmitters), improper grounding practices, and the like. When used with good engineering practices, the Loop Data Test Function serves as an integral method to verify loop integrity.

ACCESS LEVEL 3 MENU

EDIT CONFIGURATION

SET TIMES

VIEW PRINT EVENT LOG

PRINT CONFIGURATION

SYSTEM DISABLEMENTS

► LOOP DATA TEST

Then select which Loop you wish to test.

LOOP DATA TEST

► SELECT LOOP 1

SELECT LOOP 2

182

FireNET 4127 I & O Manual v1.90 UL

Then select “START TEST”.

LOOP DATA TEST

► START TEST

The Loop Data Test result will then display in real time on the screen.

LOOP DATA TEST (LOOP: 2)

Start Date : 9/05/2003 12:28:00

Good Readings: 0017824

Bad Readings: 0000000

Current Date: 9/05/2003 13:06:01

Press the Exit button when the Loop Data Test is completed.

183

FireNET 4127 I & O Manual v1.90 UL

10.4 Troubleshooting

This section is currently being developed from data collected from installation sites and technical support inquiries.

The following is an example (in FAQ format) of the information being developed:

Q – I am using a network annunciator and the Reset and Alarm Silence button don’t work - Why?

– These features must be enabled in the Network Interface settings. Using

Loop Explorer, right-click on the panel, select Edit Settings, then select the

Network Interface tab. Check the Status event box.

Q – I am using Cause and Effect to activate a relay for elevator recall, but the relay activates on all alarms. How do I get it to follow only the C&E?

– Check the Output Settings of the relay. Be sure that the General Alarm box is unchecked; otherwise, the relay will activate during a general alarm condition.

Q – When I try to connect to the panel using Loop Explorer there are no panels found.

– Be sure the correct COM port is selected in Loop Explorer. Click on the File menu, and then select Options. Select the COM port that you are using on the computer.

Q – I need to change an ALG-V smoke sensor to an ATG-EA heat sensor. Do I have to auto-learn the loops again?

– No, you can change the device type from smoke sensor to heat sensor. From the Access Level 3 menu choose Edit Configuration then Edit Device

Attributes. Select the loop and address of the smoke sensor, then select

Change Sensor Type. Select the new sensor type then press Enter. The change will take place immediately.

Q – My strobes are not flashing correctly when there is an alarm.

– Check the output pattern; strobes usually require a Continuous (Steady) output pattern. From the Access Level 3 menu choose Edit Configuration then choose Edit I/O. Select Edit Panel I/O, then Edit Default Pattern. Use the up and down arrow keys to highlight the selected pattern, then press the

Enter button.

184

FireNET 4127 I & O Manual v1.90 UL

Q – I am installing analog sounder bases (ASB) on my FireNET panel, but when I do an auto-learn the panel does not find them.

– Check the firmware revision of the panel. It must be 3.60238 or higher to use the ASB. Also be sure that each ASB is provided with 24 VDC auxiliary power.

Q – When I try to change the input action of an FRCME or DIMM using Loop

Explorer I am unable to make changes.

– Be sure the module is not assigned to any Cause and Effect programming.

Input action must be changed before the device is assigned to C&E.

Q – What are the settings for the serial printer port on the FireNET panel?

– 19,200 baud, 8 data bits, no parity, 1 stop bit.

Q – I am using the DH-98AR duct detector and I need reset-able aux power. How can I do this?

– The Auxiliary relay defaults to a reset relay when there is no programming assigned to it. Use the N/C and Common connections of the relay. When the reset button is pressed, the relay will reset power to the devices.

Q – Can I order extra keys for the FireNET panel?

– Yes, spare keyswitch models are FN-SKDK/FN-SKCK. Use this part number when ordering; 0100-03380. This includes one key for the door, and one key for the enable keyswitch.

Q – Is there a quick way to find out how many devices and sub-addresses are being used on a panel?

– Yes. Using Loop Explorer, right-click on a panel and select Edit Settings. The device and sub-address count will appear in the bottom right-hand corner of the Configure Panel Settings window. You can also use the Battery Calculator spreadsheet software included on the Loop Explorer software CD.

185

FireNET 4127 I & O Manual v1.90 UL

Section 11 - Installation Records

This section of the manual can be used to record the SLC points, RS485 addresses, and

Network nodes you have installed on the system. The tables included in this section can be filled out with this information to be referred back to later for service or troubleshooting purposes. In the near future, all of these tables are available in electronic format from the

Hochiki America Corp. web site - www.hochiki.com

. These installation records should be filled out for all installations and are useful in restoring the system configuration if the Loop

Explorer backup file is missing or corrupt.

Loop

(1-4)

11.1 SLC Loop Point Record

Use the example below to complete the information in Table 11.1 for the SLC loop points on the system:

Address

(Sub)

Zone

(1-500)

Description

Loop

(1-4)

Address

(Sub)

Zone

(1-500)

Description

015

001

002

016

001

002

(FRCME-P) Main Entry Pull Station

N/A

(R2M Module w/sub addresses)

Primary Floor Elevator Recall

Secondary Floor Elevator Recall

015

016

001

002

001

002

(ATG-EA) Office Closet Heat Detector

(ALG-V) Office Smoke Detector

Address

(1-32)

11.2 RS485 Bus Device Record

Use the example below to complete the information in Table 11.2 for the RS485 bus devices installed on the system.

Device Description Location

FN-4127-IO

FN-LCD-S

I/O board used for graphic annunciator driver

Local Serial LCD Annunciator

FN-4127 Control Panel

Main Lobby

Node

(1-64)

11.3 Network Node Device Record

Use the example below to complete the information in Table 11.3 for the Network devices installed on the system.

Device Description Location

FN-4127

FN-LCD-N

FireNET FACP for the main building

Remote Network Annunciator for system wide annunciation

South wall of the main entry lobby

Building Engineer’s Office

186

FireNET 4127 I & O Manual v1.90 UL

Loop

(1-4)

Table 11.1 FireNET 4127 SLC Loop Point Record

Address

(Sub)

Zone

(1-500)

Description

Loop

(1-4)

001

002

008

001

002

009

001

010

002

001

011

002

012

001

002

001

002

013

001

002

014

001

002

001

002

001

002

001

002

003

001

002

004

001

005

002

001

006

002

007

001

002

Address

(Sub)

008

001

002

001

002

009

001

010

002

001

011

002

012

001

002

013

001

002

001

002

014

001

002

001

002

001

002

003

001

002

001

002

004

001

005

002

001

006

002

007

001

002

Zone

(1-500)

Description

187

FireNET 4127 I & O Manual v1.90 UL

Loop

(1-4)

Address

(Sub)

Zone

(1-500)

Description

Loop

(1-4)

Address

(Sub)

Zone

(1-500)

Description

001

002

104

001

002

105

001

106

002

001

107

002

108

001

002

001

002

109

001

002

110

001

111

002

001

112

002

113

001

002

001

002

099

001

002

100

001

002

101

001

102

002

103

001

002

194

FireNET 4127 I & O Manual v1.90 UL

106

002

001

107

002

108

001

002

109

001

002

001

002

110

001

111

002

001

112

002

113

001

002

001

002

099

001

002

100

001

002

101

001

102

002

103

001

002

104

001

002

001

002

105

001

Loop

(1-4)

Address

(Sub)

001

002

119

001

002

120

001

121

002

001

122

002

123

001

002

001

002

124

001

002

114

001

002

115

001

002

116

001

117

002

118

001

002

125

001

126

002

001

127

002

001

002

Zone

(1-500)

Description

Address

(Sub)

121

002

001

122

002

123

001

002

124

001

002

001

002

125

001

126

002

001

127

002

001

002

114

001

002

115

001

002

116

001

117

002

118

001

002

119

001

002

001

002

120

001

Zone

(1-500)

Loop

(1-4)

Description

195

FireNET 4127 I & O Manual v1.90 UL

Address

(1-32)

Device

Table 11.2 RS485 Bus Device Record

Description Location

196

FireNET 4127 I & O Manual v1.90 UL

Node

(1-64)

Device

Table 11.3 Network Node Device Record

Description Location

197

FireNET 4127 I & O Manual v1.90 UL

Node

(1-64)

Device Description

These tables may be photocopied if additional pages are necessary.

Location

198

FireNET 4127 I & O Manual v1.90 UL

Appendix A - Compatible Devices

A.1 Two-Wire Smoke Detectors

Table A.1 lists the 2-wire smoke detectors that are compatible with the CZM conventional zone module.

Table A.1: Compatible 2-Wire Smoke Detectors with the Hochiki FireNET CZM Module

Manufacturer

Hochiki

Model Number

Detector

Compatibility ID

Detector

Identifier

Base

Identifier

Number of

Detectors per

CZM Module

HSB-224 25

SLR-24H

Photoelectric w/ heat

HB-5 25

SLR-835/-

835W

SLR-835H/-

835HW

SLR-835B-2

SLR-835BH-

Photoelectric

(8-35V)

Photoelectric

(8-35V) w/ thermal

Photoelectric

(8-35V)

(baseless)

Photoelectric

(8-35V) w/ thermal

(baseless)

HD-3

HD-5

NS4-224,

NS6-224

NS4-224,

NS6-224

NS4-224,

NS6-224,

NS4-224W,

NS6-224W

NS4-224,

NS6-224,

NS4-224W,

NS6-224W

HB-5 25

HB-5 18

HD-6 N/A N/A 18

DCD-135/-90

DFE-135/-

190

Heat Fixed

Temp/ Rate of Rise

Heat Fixed

Temp

HD-3

NS4-224,

NS6-224

NS4-224,

NS6-224

HB-5 25

N/A HSC HB-62 25

199

FireNET 4127 I & O Manual v1.90 UL

A.1.1 Two-Wire Smoke Detectors BOSCH

Table A.1.1 lists the 2-wire smoke detectors that are compatible with the CZM conventional zone module.

Table A.1.1: Compatible 2-Wire Smoke Detectors with the Hochiki FireNET CZM

Module

Manufacturer Model

Number

Detector

Compatibility

ID Detector

Identifier Base

Base

Identifier

Number of

Detectors per CZM

Module

BOSCH

D283A Photoelectric w/heat

HD-3 D280A HB-5 25

D265AW Photoelectric HD-3 D280AW HB-5 25

(8-35V

D256A/

D257A

D254/

D255

Heat Fixed

Temp/Rate of

Rise

Heat Fixed

Temp

HD-3 D280A HB-5 25

A.2 Reserved for Future Use

200

FireNET 4127 I & O Manual v1.90 UL

A.3 Compatible Notification Appliances

The A.3 tables list notification appliances that have been verified and listed to be compatible with the FireNET fire alarm control panel per UL864 9 th

Edition.

When non-synchronized notification appliances are used on the NAC outputs, they are rated as “Special Application” by UL Laboratories. In this case specific device compatibility is not required. For these types of notification appliances the Hochiki 10K end of line resistor PN# 0400-01046 may be used in lieu of the end of line device PN# 0400-

01023 if desired.

When synchronized notification appliances are used on the NAC outputs, they are rated as

“Special Application” by UL Laboratories with a range of compatibility from 19.3 ~ 25.95

VDC. In this case specific device compatibility is required as outlined in the tables A.3.1-

A.3.3 below. For proper operation use polarized notification appliances with a Hochiki end of line device PN# 0400-01023.

NOTE:

Synchronized audible notification appliances connected to one NAC output are not to be installed within hearing range of the synchronized audible notification appliances on another

NAC circuit.

Synchronized visual notification appliances connected to one NAC output are not to be installed within line of site of the synchronized visual notification appliances on another NAC circuit.

201

FireNET 4127 I & O Manual v1.90 UL

A.3.1 Amseco/Potter Notification Appliances (24VDC models):

Per UL864 9 th

edition Special Application testing for worst case strobe loading

(synchronized visual notification appliance) is as follows:

Max number of representative devices for worst case in-rush current (SH24W-153075) = 28

Max amount of allowable line impedance = 2.5 ohms

Manufacturer Model Number

AMSECO/POTTER

SMD10-3A

SMS1-3A

TMP Series

SH Series

SZ Series

SL Series

H Series

HP Series

SAD Series

RSD Series

SLB Series

SHB Series

SHP Series

SSC Series

SFH Series

CM Series

SCM Series

MBA Series

SB Series

RSB Series

Type

Dual Zone/Daisy Chain Sync Module

Single Zone Sync Module

Temporal Pattern Module

Select-A-Horn/Strobe Series

Select-A-Horn/Strobe Series (motor driven horn)

Select-A-Strobe Strobes Series

Select-A-Horn Series

Mini-Horn Series

Stand Alone Strobe Series

Retrofit Strobe Series

Outdoor Strobe Series

Outdoor Horn/Strobe Series

Select-A-Horn/Strobe Series (mini-horn)

Select-A-Speaker/Strobe Series

Select-A-Speaker/Strobe Series (low profile/hi-wattage)

Chime Series

Select-A-Chime Strobe Series

Motor Bell Series

Select-A-Bell/Strobe Series

Retrofit Select-A-Bell/Strobe Series

FS Series

BZ Series

Slow Whoop Sounder Series

Motor Driven Horn Series

NOTE 1:

Please refer to the notification appliance device instructions per the appropriate model and series noted above for specific installation instructions and details required by the manufacturer and UL listing for that device.

NOTE 2:

Please refer to the sync module instructions per the appropriate model and series noted above for specific installation instructions and details required by the manufacturer and UL listing for that device.

NOTE 3:

The DCP-SOM-A and DCP-SOM-AI modules are suitable for use with

Amseco/Potter notification appliances in both a Class A and Class B configuration with the

Amseco/Potter sync module employed.

202

FireNET 4127 I & O Manual v1.90 UL

A.3.2 Cooper/Wheelock Notification Appliances (24VDC models):

Per UL864 9 th

edition Special Application testing for worst case strobe loading

(synchronized visual notification appliance) is as follows:

Max number of representative devices for worst case in-rush current (RSS-24MCW) = 41

Max amount of line impedance = 2 ohms

Manufacturer Model Number

COOPER/WHEELOCK SM/DSM Series

NS Series

NH Series

AS Series

AH Series

HS4 Series

HS Series

MT Series

Type

Sync Modules

Horn/Strobe Series

Horn Series

Audible/Strobe Series

Audible Series

Horn/Strobe Series

Horn Series

Multi-tone Horn/Strobes Series

AMT Series Multi-tone Horn/Strobes Series

CH Series

CSX Series

MB Series

RSS/R/P Series

MIZ Series

E50/60 Series

E70/90 Series

ET70/90 Series

Chimes/Strobe Series

Explosion Proof Bell Series

Motor Bell Series

Strobe Series

Mini-Horn Series

Speaker/Strobe Series (high-efficiency)

Speaker/Strobe Series (low profile)

Speaker/Strobe Series

ET80/1010/1080 Series Speaker/Strobe Series (vandal resistant)

S8 series Speaker/Strobe Series (8” size)

STH Series

PS Series

Cluster Speaker/Strobe Series

NAC Booster Series

NOTE 1:

NOTE 2:

NOTE 3:

The DCP-SOM-A and DCP-SOM-AI modules are suitable for use with

Cooper/Wheelock notification appliances in both a Class A and Class B configuration with the Cooper/Wheelock sync module employed.

203

FireNET 4127 I & O Manual v1.90 UL

A.3.3 Gentex Notification Appliances (24VDC models):

Per UL864 9 th

edition Special Application testing for worst case strobe loading

(synchronized visual notification appliance) is as follows:

Max number of representative devices for worst case in-rush current (GEC3-24WR) = 32

Max amount of line impedance = 2 ohms

Manufacturer

GENTEX

Model Number

AVSM/AVS-44 Series

GCS/GCC Series

GES3/GEC3 Series

GES/GEC/GEH Series

ST/HS Series

WGES/WGEC Series

GB Series

Type

Sync Modules

Commander 4 Horn/Strobe Series

Commander 3 Horn/Strobe Series

Commander 2 Horn/Strobe Series

Commander 1 Horn/Strobe Series

Weatherproof Horn/Strobe Series

Alarm Bell Series

SSPK Series Speaker/Strobe Series

SSPKC Series Speaker/Strobe Series (ceiling mount)

GE3A/GE3B/GE3G/GE3R Series Commander 3 Horn/Strobe Series (mass notification)

GCA/GCB/GCG/GCR Series Commander 4 Horn/Strobe Series (mass notification)

NOTE 1:

NOTE 2:

NOTE 3:

The DCP-SOM-A and DCP-SOM-AI modules are suitable for use with Gentex notification appliances in both a Class A and Class B configuration with the Gentex sync module employed.

204

FireNET 4127 I & O Manual v1.90 UL

A.3.4 System Sensor Notification Appliances (24VDC models):

Per UL864 9 th

edition Special Application testing for worst case strobe loading

(synchronized visual notification appliance) is as follows:

Max number of representative devices for worst case in-rush current (P1224MC) = 42

Max amount of line impedance = 2 ohms

Manufacturer

SYSTEM SENSOR

Model Number

MDL Series

P1224 Series

S1224 Series

PC24 Series

SC24 Series

H12/24 Series

HC12/24 Series

SP2C Series

SP2R Series

Type

Sync Modules

SpectrAlert Horn/Strobe Series

SpectrAlert Strobe Series

SpectrAlert Horn/Strobe Series (ceiling)

SpectrAlert Strobe Series (ceiling)

SpectrAlert Horn Series

SpectrAlert Speaker/Strobe Series (ceiling)

SpectrAlert Speaker/Strobe Series

SP2W Series

SP3R Series

SP3W Series

CH24 Series

CH1224 Series

SpectrAlert Speaker/Strobe Series

SpectrAlert Speaker/Strobe Series (hi-output)

SpectrAlert Chime/Strobe Series

SpectrAlert Chime Series

PA400 Series Mini-Horn Series

NOTE 1:

NOTE 2:

NOTE 3:

The DCP-SOM-A and DCP-SOM-AI modules are suitable for use with System

Sensor notification appliances in a Class B configuration with the System Sensor sync module employed.

The DCP-SOM-A and DCP-SOM-AI modules are NOT suitable for use with the System

Sensor notification appliances when connected to the System Sensor sync module in a

Class A configuration.

205

FireNET 4127 I & O Manual v1.90 UL

A.4 Compatible 24VDC Devices

For proper operation use 24VDC polarized devices. When used on a supervised output or

NAC, be sure to use with a Hochiki 10K end of line resistor PN# 0400-01046. When used on the AUX24VDC output the supervision resistor is not necessary.

The AUX24VDC and supervised voltage outputs are rated as Regulated by UL

Laboratories. In this case specific device compatibility is not required. Be sure to verify current loading of the panel when attaching devices to these outputs by using the battery calculator shown in section 2.6 of this manual.

Table A.4 lists 24VDC devices that are compatible with the FN-4127 fire alarm control panel

Regulated

outputs, though specific compatibility is not required when outputs are rated as

Regulated

by UL.

Table A.4: Compatible 24VDC Devices with the FN-4127 Fire Alarm Control Panel

Model Number Type Manufacturer

Hochiki America

FN-LCD-N

FN-4127-IO

SRA-24

Network LCD Annunciator

16 Channel Input Output Board

Reflective Beam Detector

FN-LCD-S

SOM

Serial LCD Annunciator

Supervised Output Module

ASB Analog Sounder Base

Bosch

Hochiki/Altronix

GE/IFS

RSG

DH-98P/I/HV Conventional Duct Dectector

D9068/D7033 Contact Dialer (DACT)/Programmer

ULX Series

D1300

DH24 Series

AUX 24VDC Power Supplies (2.5, 4, 6, & 10 Amp)

RS485 to Fiber Optic Converter (24VDC model)

Door Holder Series (24VDC models)

206

FireNET 4127 I & O Manual v1.90 UL

A.4.1 Compatible 24VDC Devices BOSCH

For proper operation use 24VDC polarized devices. When used on a supervised output or

NAC, be sure to use with a Hochiki 10K end of line resistor

PN# 0400-01046. When used on the AUX24VDC output the supervision resistor is not necessary.

The AUX24VDC and supervised voltage outputs are rated as Regulated by UL

Table A.4.1 lists 24VDC devices that are compatible with the FN-4127 fire alarm control panel Regulated outputs, though specific compatibility is not required when outputs are rated as Regulated by UL.

Table A.4.1: Compatible 24VDC Devices with the FN-4127 Fire Alarm Control

Panel

Manufacturer

Model Number

Type

BOSCH

D327A Supervised Output Module

D300A/D300-AHV Conventional Duct Detector

207

FireNET 4127 I & O Manual v1.90 UL

A.5 Using the Bosch D9068 Dialer with FireNET

A.5.1 Using the Bosch D9068 Contact Dialer with FireNET (Diagram)

FireNET 4127 I & O Manual 208 v1.90 UL

A.5.2 Programming FireNET for use with the Bosch D9068 Dialer

There are two methods possible when programming the FireNET for use with the Bosch

D9068 dialer. The FireNET front panel controls or Loop Explorer configuration software may be used:

When using the front panel controls to program the FireNET panel for use with the

Bosch D9068 dialer, use the following steps

1. Program the onboard “Fire 2” relay for “AC Fail Delay” operation:

-> First enable the AC Fail Delay option in the “Access Level 3 \ Edit Configuration \ Edit I/O \

Edit Panel I/O \ Edit Panel Outputs \ Edit Fire 2 Contact” screen:

-> Second select an AC Fail Delay time value in the “Access Level 3 \ Edit Configuration \

Edit I/O \ Edit Panel I/O \ Edit AC Fail Report Delay” screen:

2. Make sure the panel and outputs listed below are left at the default values in the

Panel I/O screens:

• Fire 1 Contact (General Alarm / Common Fire)

• Trouble Contact (Common Trouble)

• Supervisory Output (Common Supervisory)

• Trouble Input (Common Trouble)

3. The auxiliary contact connected to Bosch D9068 Dialer Input #1 is a spare and can be programmed for any function.

FireNET 4127 I & O Manual 209 v1.90 UL

When using the Loop Explorer configuration software to program the FireNET panel for use with the Bosch D9068 dialer, use the following steps

1. Program the onboard “Fire 2” relay for “AC Fail Delay” operation:

Select AC Fail Delay when using the Bosch D9068 Dialer with FireNET.

210

FireNET 4127 I & O Manual v1.89UL

2. Programming the AC Fail Delay value…

Program the AC Fail delay value between 0 – 24 Hours.

3. Make sure the panel and outputs listed below are left at the default values in the

Panel I/O screens:

• Fire 1 Contact (General Alarm / Common Fire)

• Trouble Contact (Common Trouble)

• Supervisory Output (Common Supervisory)

• Trouble Input (Common Trouble)

4. The auxiliary contact connected to Bosch D9068 Dialer Input #1 is a spare and can be programmed for any function.

211

FireNET 4127 I & O Manual v1.89UL

5. Input/Output Table:

FireNET Panel

Fire 1 Relay

Trouble Relay

Fire 2 Relay

Supervisory Relay

Auxiliary Relay

Trouble Input 1

Bosch D9068 Dialer

Dialer Input 5

Dialer Input 4

Dialer Input 3

Dialer Input 2

Dialer Input 1

Dialer Trouble Relay Output

A.5.3 Installation notes when using the Bosch D9068 Dialer with FireNET

NOTE 1:

The Bosch D9068 slave contact dialer must be installed within 20ft, in conduit, and within the same room as the FireNET control panel.

NOTE 2:

Both the AC Fail Relay in FireNET and the Bosch trigger input assigned to AC Fail functionality have the ability to program an AC Fail Delay time value. The user must choose and program one or the other, not both, or the AC Fail Delay values of each unit will be combined.

NOTE 3:

When programming the AC Fail Relay value in FireNET, the value can be set between 0 and

24 hours. UL864 9 th

Edition only recognizes setting this value between 1-3 hours. Setting this value to 0 or between 4 – 24 hours is not in compliance with the UL864 Edition 9 standard. See summary below.

• AC Fail Delay = 1 – 3 hours (complies with UL864 Ed. 9)

• AC Fail Delay = 0, 4 – 24 hours (does not comply with UL864 Ed. 9)

Please see the beginning of this manual for a list of all program settings that can be adjusted outside compliance of the UL864 Edition 9 standard.

212

FireNET 4127 I & O Manual v1.89UL

A.6 Using the FN-CTM City Tie module with FireNET

When using the FN-CTM City Tie module for Local Energy City-Tie applications, use the Fire

Routing supervised output (see section 3.5). This output by default is programmed for general fire alarm operation.

The supervised NAC outputs of the FireNET panel may also be used. The NAC outputs must be programmed for General Alarm with a Continuous output pattern (see Section 3.4).

Please reference the FN-CTM City Tie module installation instructions included with the module for additional details.

Note: When City Tie wiring leaves the building, install 26 AWG wire between the City Tie module and the Trip Coil. A short length of 24

AWG wire must be used to interface between the 26 AWG and the City Tie Module terminal block.

Maximum coil resistance and wire resistance must not exceed 30

Ohms.

Ground Wire

Local Energy

City Tie

Trip Coil

E.O.L. DEVICE

PART NUMBER

Hochiki America Corporation

FN-CTM

City Tie Module

SERIAL NO.XXXXX

For Dry Indoor Use Only

City Tie

EOL

NAC Input

S8255

For Proper Installation see HA-06-137 Rev 5/06

Signaling Devices

ISSUE NO. BF-8887

UL Listed

Fire Alarm

Control Panel

NAC Circuit

Wiring Polarity Shown in

Alarm Condition.

E.O.L. DEVICE

PART NUMBER

0400-01046

10K OHM 1/4W

All Wiring is Power Limited, Connect only to Power Limited Circuits.

For Use Only With Supervised Circuits.

213

FireNET 4127 I & O Manual v1.89UL

Use either Fire

Routing or NAC output on the

FireNET control panel. See

Section 3.4 &

3.5 for details **

A.7 Using the FNV-MP with FireNET

When using the FNV-MP with FireNET panel, refer to below wiring diagram. Please reference the installation instructions of the FNV-5010 for all other connection details.

214

FireNET 4127 I & O Manual v1.89UL

A.8 Changing the FN-PS402 Power Supply to 240VAC operation

When converting the FN-PS402 four amp power supply to 240VAC, please follow the directions described in this section. The FN-PS402 can operate with 120VAC or 240VAC input. By default, the power supply is configured for 120VAC operation. To change it to 240 volts AC, follow the steps below –

1) Be sure that the FireNET control panel is NOT powered during this procedure!

2) Carefully remove the cover of the power supply.

3) In the upper left hand corner of the circuit board you will see a jumper labeled R72. Remove this jumper from the pins, and re-install the cover.

The power supply is now properly configured for 240 VAC operation.

The FN-PS402 is set for 120VAC operation when the R72 jumper is in place.

The FN-PS402 is set for 240VAC operation when the R72 jumper is removed.

WARNING

– Do NOT apply 240 VAC to the FireNET control panel unless the power supply has been configured to operate at 240 volts! Doing so will damage the panel, requiring it to be returned to the factory for repair!

215

FireNET 4127 I & O Manual v1.89UL

Appendix B – Panel Door Label Drawing

Class A Style 6 or 7 - For SLC Devices (Smoke / Heat Sensors and Modules)

AGENCY LISTINGS AND REQUIREMENTS

- Proprietary Service (DACT)

- Auxiliary Service (Local Energy) Install in accordance with NFPA 70, 72 and 13.

The FireNET 4127 is suitable as follows:

- Commercial Protected- Premises Control Unit for Local signaling. Install Indoors only in a dry environment.

- Types of signaling services are automatic, manual, waterflow, & sprinkler supervisory.

- Style 4, 6, or 7 for Signaling Line Circuits

- Style Y for Notification Appliance Circuits

- Non-coded signaling

- Central Station Service (DACT)

- Remote Station Service (DACT)

- UL Releasing Function for Pre-Action with use of SOM-R Module

The FireNET 4127 has been verified to comply with

FCC Rules Part 15, Class A Operation is subject to the following conditions:

1. This device may not cause radio interference.

2. This device must accept any interference received, including any that may cause undesired operation.

F.C.C. registration number: US:HBPAL01BFN-DAC

: SLC LOOPS 1 - 4 ARE SUPERVISED

: Style 7 - Refer to Section 5.17.1 in Manual

: SLC Max Impedance is 50 Ohm, 1uF, 1mH

Class B Style 4 - For SLC Devices (Smoke / Heat Sensors and Modules)

SLC INITIATING DEVICES

ZERO OHM SHORTING

JUMPERS MUST BE USED

FOR CLASS B OPERATION

P/N 0400-01025

Total wire must not exceed 10,000 feet from the control panel when using

#14 AWG

18 AWG

16 AWG

14 AWG

3900 Feet

6200 Feet

10,000 Feet

See FireNET Installation Manual as noted below for SLC branch circuit cable requirments

FireNET employs an option for Sounder Time-

Out (for NAC/SOM/ASB), which can be programmed in 5 min. increments between 5-60 min. Option is disabled by setting the value to 0 (default condition).

Conventional Relay Contacts rated for 1A @ 30VDC.

Must be connected to power limited source.

(Not supervised) (Resistive)

See for additional NAC requirements.

Class B Style Y - For Indicating Devices

+ + +

Hochiki America

EOL Device

(EOLD)

P/N 0400-01023

(Supervised)

Refer to A.3 for Compatible Devices

(Special Application for synchronized and non-synchronized loads)

EXAMPLE OF FIRE ROUTING, TROUBLE

ROUTING, & PROGRAMMABLE OUTPUT

POLARITY

REVERSING

DEVICE

500 mA @24VDC max.

10K OHM

END-OF-LINE

RESISTOR

(EOLR)

P/N 0400-01046

(Supervised)

10K OHM END-OF-LINE RESISTOR (EOLR) P/N 0400-01046

(Supervised)

1N4004S END-OF-LINE DIODE (EOLD) P/N 0400-01024

(Supervised)

DIGITAL INPUTS (EXAMPLE FOR INPUTS 1-8)

USE DRY CONTACTS ONLY

(Not Supervised) Refer to A.4 for

Compatible Devices

(Regulated)

Printer

Cable must not exceed 20ft.

(real-time event logging)

RS485

NETWORK

TX/RX

LED’s

ENABLE CONTROLS

KEYSWITCH (not present on the Denver Door build)

RS232 DATA PORT

FOR CONFIGURATION

COMPUTER & SOFTWARE

(Disconnect after use)

TERMINAL STRIP ELECTRICAL RATINGS FOR THE POWER SUPPLY MODULE

TB6

TB4

TB3

+24VDC

DC RTN

Earth Ground

AC Neutral

AC Line

+DC Output

-DC Output

+ Battery

- Battery

N/A

120VAC, 50/60Hz

240VAC, 50/60Hz

120VAC, 50/60Hz

240VAC, 50/60Hz

+24VDC

DC Common

+24VDC

DC Common

X1 - TOP TERMINAL STRIP ELECTRICAL RATINGS FOR MAIN CONTROL UNIT

WARNING

THIS UNIT INCLUDES AN

OPTIONAL ALARM

VERIFICATION FEATURE that will result in a delay of the system alarm signal from the indicated circuits. The total delay time (control plus smoke detectors) shall not exceed 60 seconds. No other smoke detector shall be connected to these circuits unless approved by the local

Authority Having Jurisdiction.

*Zone(s)________________

*where alarm verification is used

Programmed Delay is 60 seconds by default. The delay is programmable from 5

– 60 seconds.

1, 5, 9, 13

2, 6, 10, 14

3, 7, 11, 15

4, 8, 12, 16

17, 20, 23, 26, 29

18, 21, 24, 27, 30

19, 22, 25, 28, 31

32, 34, 36, 38

33, 35, 37, 39

- OUT

+ OUT

- IN

+ IN

VOLTAGE

OUTPUTS

REMOTE/AUX

INPUTS

DC GROUND

COMMS

AUX

24V

NETWORK

IN/OUT

SLC LOOPS

1 - 4

RELAYS

NAC 1-4

Signaling Line Circuit. Out terminals used for Class B or A wiring.

Signaling Line Circuit. In terminals used for return loop for Class A wiring.

Fire 1, Trouble , Fire 2, Supervisory, and Auxiliary condition relay contacts

Notification Appliance Circuits #1-4.

(EOLD PN# 0400-1023 required)

SUPERVISED POLARITY REVERSING SIGNALING

OUTPUTS FOR FIRE, TROUBLE, PROGRAMMABLE

REMOTE CONTROL DIGITAL PULL-DOWN INPUTS

SIGNAL FOR ACTIVATING REMOTE INPUTS

RS485 TO I/O BOARDS

AUXILIARY 24V SUPPLY

RS485 TO OTHER PANELS

FireNET WIRING DIAGRAM

P/N 1700-04345 DATE 07/02/2010

32VDC

30VDC

24VDC

X2- SIDE TERMINAL STRIP ELECTRICAL RATINGS FOR MAIN CONTROL UNIT

24VDC

0VDC

12VDC

24VDC

12VDC

400mA

1 A

2.5A

500mA

30mA

500mA

100mA

500mA

100mA

FireNET 4127 I & O Manual 216

N/A

2.1A

1.1A

2.1A

1.1A

0 - 4 Amps

5A Max

All circuits are inherently Power

Limited except AC/Battery inputs.

All Supervised Circuits are identified.

RS485 TO I/O BOARDS (Supervised)

AUX 24VDC POWER TO I/O BOARDS 500 mA max.

(Supervised)

RS485 FROM PREVIOUS FireNET PANEL

ON NETWORK (Supervised)

RS485 TO NEXT FireNET PANEL

ON NETWORK (Supervised)

Refer to A.4 for

Compatible Devices

(Regulated)

NOT

USED

NOTE 1:

(Single Circuit Synchronization)

Synchronized audible notification appliances connected to one NAC output are not to be installed within hearing range of the synchronized audible notification appliances on another NAC cirucuit.

Synchronized visual notification appliances connected to one NAC output are not to be installed within line of site of the synchronized visual notification appliances on another

NAC cirucuit.

+ - +

For synchronized NAC applications, the outputs are Special Application with a compatibility range of 19.3 ~

25.95 VDC.

F2 – 3A, 250VAC, slow blow, 5 x 20mm fuse

AC 120VAC INPUT

20 AMP Breaker

Max

(supervised)

EARTH GROUND STUD

NEGATIVE

(-)

12 VOLT Sealed Rechargeable

Battery

60 AH Maximum

(Supervised)

POSITIVE

(+)

10 Amp in-line Fuse (supervised)

Bussman AGC-10 or equiv.

Battery cables and jumpers are supplied with the panel

HOCHIKI AMERICA CORPORATION

12 VOLT Sealed Rechargeable

Battery

60 AH Maximum

This Product shall be installed in accordance with FireNET Installation

Manual: PN # 1700-09948

BATTERIES SHOULD BE INSPECTED ANNUALLY & REPLACED EVERY 3-5 YEARS

(DO NOT PARALLEL BATTERIES)

USE ONLY UL RECOGNIZED SEALED LEAD ACID BATTERIES

Version # 1.88

Issued: 07/02/2010 v1.90 UL

Appendix C - WARRANTY

Hochiki America Corporation manufactured equipment is guaranteed to be free from defects in materials and workmanship for a period of three (3) year from date of original shipment. HOCHIKI will repair or replace, at its option, any equipment which it determines to contain defective material or workmanship. Said equipment must be shipped to HOCHIKI prepaid. Return equipment will be prepaid by HOCHIKI. We shall not be responsible to repair or replace equipment which has been repaired by others, abused, improperly installed, altered or otherwise misused or damaged or exposed to conditions outside the products specifications in any way. Unless previously contracted by HOCHIKI, HOCHIKI will assume no responsibility for determining the defective or operative status at the point of installation, and will accept no liability beyond the repair or replacement of the product at our factory service department. Please contact

HOCHIKI’s Sales department for proper procedure for claims and return of merchandise.

Hochiki America Corporation

7051 Village Drive, Suite 100

Buena Park, CA 90621-2268

1-800-845-6692 [email protected]

End of Manual

August 2010

FireNET 4127 I & O Manual 217 v1.90 UL

Key features

Analog addressable technology
A variety of input and output devices
A user-friendly interface
Remote monitoring and control capabilities

Frequently asked questions

The power consumption of the FireNET 4127 varies depending on the number of devices connected to the system. However, the typical power consumption is less than 100 watts.

The maximum number of devices that can be connected to the FireNET 4127 is 99.

The FireNET 4127 uses 12-volt, sealed lead-acid batteries.