TC70
QUICK START
GUIDE
CARD INSTALLATION
FEATURES
Note:
Remove protective shipping film that covers the touch screen, exit
window and camera window before using.
12
13
14
15
11
10
1. Insert the bottom of the battery into the battery compartment.
2
22
19
2. Insert the hand strap plate into the handstrap slot.
2. Insert the microSD card into the card holder. Push the card all the way into the
card holder.
21
20
3
4
5
Touch Screen
Light Sensor
Proximity Sensor
Power Button
Receiver
Charging/Notification LED
Data Capture LED
Front-facing Camera
Note 1: To reset the TC70, press and hold the Power button until the menu
appears and then select Reset.
4. Rotate the battery down into the battery compartment and press the battery
down until it snaps into position.
2
6
1
8
9
10
11
12
13
14
15
1. Remove hand strap filler plate.
1. Lift the access door.
17
18
7
PTT Button (programmable)
Scan Button
Back Button
Home Button
Power Input
Search Button
Menu Button
BATTERY INSTALLATION
16
9
8
1
2
3
4
5
6
7
MicroSD Card Installation (Optional)
23
HANDSTRAP AND BATTERY INSTALLATION
16
17
18
19
Hand Strap Mounting Point
Camera Flash
Rear-facing Camera
Interface Connector
20
21
22
23
2. Rotate the battery down into the battery compartment.
NOTE :
Proper position of the microSD card — the card connector (i.e., gold contacts) should
be facing down.
Exit Window
Volume Button
Battery Release Latch
Hand Strap
5. Place the hand strap clip into the hand strap attachment slot and pull down to lock into
place.
3
Notifications
Data Capture LED:
Green: Good Decode
Red: Data capture in process
Blue: Application notification Charging/Notification
Data Capture
Charging\Notification LED:
Slow blinking amber: Battery charging
Solid green: Fully charged
Fast blinking amber: Charging error
Slow blinking red: Charging aged battery
Solid red: Fully charged aged battery
Fast blinking red: Charging error aged battery
Slow blinking blue: Application notification
3. Insert the bottom of the battery into the battery compartment.
3. Press the battery down until it snaps into position.
3. Replace the access door. Ensure that it is properly seated.
4
6. Lift the hand strap ribbon off the hook material.
7. Slide the pad and adjust the ribbon for best fit.
8. Press the ribbon down to secure to hand strap.
BATTERY REMOVAL
1.
2.
3.
4.
Press the Power button until
the menu appears.
Touch Power Off.
If installed, unlatch the hand
strap. Push the hand strap clip
up toward the top of the TC70
and then lift.
Press the battery release
latches in and lift the battery
from the TC70.
DATA CAPTURE OPTIONS
ACCESSORIES
5-Slot Charge Only Cradle
5-Slot Charge Only Cradle
with Battery Charger
5-Slot Ethernet Cradle
2-Slot Charge
Only Cradle
4-Slot Battery
Charger
Battery
Charger Adapter
2-Slot USB/Ethernet Cradle
Imaging
Magnetic Stripe Reader
Charging Cable Cup
Symbol® is a registered trademark of Symbol Technologies, Inc. All other
trademarks and service marks are proprietary to their respective owners.
© 2014 Symbol Technologies, Inc. All rights reserved.
MN000976A01 Rev. A — October 2014
AVOID EXTREME
WRIST ANGLES
Snap-On USB Cable
Stylus
with Tether
Holster
2.
3.
4.
5.
For more information, see the TC70 User Guide and the TC70 Integator
Guide available at: http://www.motorolasolutions.com/support.
Camera Photo
Audio Adapter
1.
Symbol Technologies, Inc.
One Motorola Plaza Holtsvilee, NY 11742-1300, U.S.A.
AVOID EXTREME WRIST ANGLES
Ensure that an application is open and a text field is in focus
(text cursor in text field).
Point the exit window at the bar code.
Press and hold the Scan button.
The red laser aiming pattern turn on to assit in aiming.
When the TC70 decodes the bar code the Data Capture LED
light green and a beep sounds.
Release the Scan button.
1.
2.
3.
Touch
> Camera.
Point the TC70 at an object.
Touch the on-screen shutter button.
">
