WWW.PROTOCOLPERFORMANCE.COM
USER GUIDE AND INSTALLATION MANUAL
SHAVE DOOR HANDLE SYSTEM
PPP35K
IMPORTANT NOTICE: Upon completion of installation,
you may have extra unused wires on the wiring
harness. Do not be concerned. These wires are used
for features available on other models.
15A FUSE
87
87a
86
RELAY
85
87
85
87a
86
30
RELAY
30
+ PARKING LIGHTS
+12V
+12V
OPTIONAL
PASSENGER
DOOR SOLENOI
WHITE/BLACK (CH6 – 500mA)
RED/BLACK (CH5 – 500mA)
D
Solenoid
(CH4 – 500 mA)
RELAY
(CH3 – 500 mA)
(CH2 – 500 mA)
87
85
87a
86
(CH1 – 500 mA)
30
(STARTER/IGNITION KILL OUTPUT)
+12V
SWITCH IGNITION POWER
CHASSIS
GROUND
DRIVER
DOOR SOLENOI
D
Solenoid
SAFETY
RELAY
87
87a
86
85
30
KL800
VALET SWITCH
MULTI-FUNCTION KITS
Remote Receiver
Connector
BLACK
BLUE/WHITE
I M PO RTA NT!
Please reference the
receivers wiring diagram for
all other wire connections.
GREEN/WHITE
87
87a
DRIVER
86
85
87a
86
30
DOOR RELAY
85
30
DOOR RELAY
+
–
PASSENGER
87
FUSE
30A
©2004 The Hoffman Group L.L.C. All rights reserved. PPP35K-KL800 1 of 2
1
Drivers Door
Anytime
2
Passengers Door
Anytime
3
1st channel output
Anytime
4
2nd channel output
Anytime
1+3
3rd channel output
Anytime
2+4
4th channel output
Anytime
1+2
5th channel output
Anytime
3+4
6th channel output
Anytime
Revised 12/22/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG
instructions. Installation by qualified automotive professionals is highly recommended.
LLC is also not responsible for any property damage or personal injuries resulting from the above
1
WIRING DIAGRAMS
SOLENOID INSTALLATION
ALARM KITS
1. Using the 2 standard screws and washers provided attach the
bracket to the solenoid. Install the smaller screw and washer on the
Remote Receiver
Connector
Clean and lubricate the latch.
3. Using the hex bolts mount the solenoid to a clean piece of metal
on the door. Ideally you want to mount the solenoid so you have a
87
87a
86
85
87a
86
30
DOOR RELAY
DRIVER
PURPLE
direct pull from the door latch to the solenoid. If you are unable to
85
mount the solenoid with a direct pull, relocate the solenoid to best fit
30
DOOR RELAY
+
–
PASSENGER
87
solenoids rear terminal.
2. Remove door ’s interior door panel and locate the factory latch.
BROWN/BLUE
GREEN/WHITE
I M P O R TA NT!
Please reference the
receivers wiring diagram for
all other wire connections.
your door panel. In some cases you will need to use the cable
extension kit (SVAEX) to redirect the cable from the latch to the
solenoid. (figure 1)
FUSE
4. Create a loop with the cable and secure with the aluminum crimp
30A
around the door latch. (See figure 2) Run cable through door
avoiding all moving parts to the solenoid.
IMPORTANT NOTICE: Upon completion of installation,
you may have extra unused wires on the wiring
harness. Do not be concerned. These wires are used
for features available on other models.
5. Run cable through the eye of the solenoid, create a loop, and
secure w/ aluminum crimp. (See figure 3)
NOTE: for best performance you will want to keep a little slack in
the cable.
OEM
LATCH
CABLE
CRIMP
CABLE
HOUSING
CABLE
SOLENOID
©2004 The Hoffman Group L.L.C. All rights reserved. PPP35K-KL800 - 2 of 2
SOLENOID
CABLE
CRIMP
Revised 12/22/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG
instructions. Installation by qualified automotive professionals is highly recommended.
LLC is also not responsible for any property damage or personal injuries resulting from the above
2
">
