USER MANUAL
1. What’s in the Box:
NOTE: The memory card is already inserted in your GOGOGATE
GOGOGATE DEVICE
Memory Card
WIRELESS ADAPTER
A B
ONE WIRELES
DOOR SENSOR
( 2 parts A +B)
POWER SUPPLY 3 x CABLES CABLE CONNECTOR
2 x SCREWS
NOTE: Cables have been pre-connected to the cable connector for your convenience.
2
WARNING
TO PREVENT SERIOUS INJURY OR DEATH FROM MOVING GARAGE DOORS OR GATES:
- DO NOT let children use the GOGOGATE product and app without adult supervision.
- ONLY Operate your GOGOGATE device when you are in clear view of your garage or gate and you have verified
that there are no objects obstructing the operation of the door. ALWAYS wait for garage door or gate to be
completely closed.
- NEVER operate the remote access feature of your GoGoGate without ensuring that there is an adult physically
present in front of the door or gate validating that it is safe to start the remote operation of your device
2. Understanding your GoGoGate:
3
6
1
2
RESET
8
7
NOTE: your GOGOGATE has no power on/off switch.
The device consumes very little power and needs to be always on for your app to open and close your garage when you need it.
4
5
1
2
3
4
5
6
7
SD Memory card Slot: The card is used to operate your GOGOGATE and also for
future Software upgrades. IT SHOULD
NOT BE REMOVED while the device is powered on.
Cable slot: Connects the 3 pre-assembled garage cables to your garage door wall buttons.
WiFi Port: This is where you will insert the Wireless USB adapter supplied with your product. Once inserted do not remove. This is needed to connect to your wireless home network.
Left (L) and Right (r) light receiver.
These light receivers are used to program all functions of your GoGogate device with your smartphone.
5 Led Indicators:
G1 , G2, G3 indicates the status of garage door # 1,2 and 3. These LEDs will display a fixed green light when a specific door is activated.
The STATUS LED will blink green when the device is operating properly. When connecting the wireless sensors to the
GoGoGate, the status LED will blink fast twice to indicate that the GoGoGATE device is receiving the signals from the wireless door sensors.
The POWER LED will be a red light when the device is connected to the power source.
Programming AREA: This is where you will place your Smartphone
(SCREEN FACING DOWN) to program your GoGogate device.
Power input: Connects the 5VDC power supply to the device.
8
Reset button: Press this button during
5 seconds until you hear 1 beep. This will restore your GoGoGate to factory settings.
3
3. What do you need for installation:
· A screw driver
· The GoGogate app installed on your smartphone.
· Your home Network name (also called SSID) and password
· About 20m of your time
A) Start Your Initial Installation : STEP 1
Steps below are to connect 1 garage door. Just repeat these steps to connect more garage doors.
GARAGE OPENER
WALL BUTTON EXAMPLE 1
GARAGE OPENER
WALL BUTTON EXAMPLE 2
4
1
Use a screw driver to open or unscrew your garage door wall button. (You may have 1 ,2 or 3 wall mounted buttons depending on the number of garage doors you have. The GOGOGATE works with up to 3 garages.)
See our installation video at www.gogogate.com for more information.
GARAGE OPENER
WALL BUTTON EXAMPLE 2
GARAGE OPENER
WALL BUTTON EXAMPLE 1
NOTE: although the cables that connect to the back of your garage door wall mounted buttons maybe of different colors, for the
GogoGate product this does not matter. (ie. polarity or color are not important). Attach the cables provided with your product to either of the 2 cables found on the back of your garage buttons.
GOGOGATE Cable
GARAGE OPENER
WALL BUTTON EXAMPLE 2
GOGOGATE Cable
White Cable
Red Cable
GOGOGATE
Cable
GOGOGATE
Cable
2
Connect the cable provided in the box to your garage door buttons. (See drawings).You will have to loosen the 2 screws to connect the cables. Although these are low voltage connectors, you must cut the power (ie turn power off) to the wall mounted buttons prior to installation.
5
GARAGE OPENER
WALL BUTTON EXAMPLE 1
GARAGE OPENER
WALL BUTTON EXAMPLE 2
6
3
Reconnect your wall mount button to the wall. (show photo)
GARAGE OPENER
WALL BUTTON EXAMPLE 1
YOUR GARAGE
DOOR CONTROL
GOGOGATE
DEVICE
Make sure connector is
Pushed in all the way.
GARAGE OPENER
WALL BUTTON EXAMPLE 2
GOGOGATE
DEVICE
Note: if you are connecting multiple garage door wall buttons to your gogogate, complete step 2 with all wall buttons before inserting the cable connector into the gogogate device.
Make sure connector is
Pushed in all the way.
4
Snap the green cable connector (provided) into the GOGOGATE cable slot.
7
WIRELESS
ADAPTER
8
POWER
SUPPLY
CABLE
CONECTOR
5
Plug your wireless adapter antenna in your gogogate and then connect your gogogate to the power supply outlet . See drawing.
STEP 2
WIRELESS DOOR SENSOR
Attach your wireless sensors to your garage door as per drawing below.
A
PLACE THIS PART
ON GARAGE DOOR
B
PLACE THIS PART
ON THE WALL
Always install your wireless door sensors with the garage doors in a closed position.
Please be sure to remove the tape covering the battery prior to installation.
PLACE THE SENSORS ON THE UPPER PART
OF YOUR GARAGE DOOR WALL.
4 Digit Code
1
Remove Battery protector tape
2
Place on the wall with the double-sided fastening strip.
Note: write down and store in a safe location the 4 digit code located on the front of your sensor.
PLACE SENSOR A & B
AS CLOSE TO EACH OTHER AS
POSSIBLE WITHOUT TOUCHING
9
10
CHECK THE OPERATION OF YOUR WIRELESS DOOR SENSOR:
Once your wireless sensors are properly positioned on the garage door, open your garage door via your existing push button. Make sure that when the garage door opens the STATUS light of your gogogate is blinking fast during 1-2 seconds. The LED should also blink fast for 2 seconds when you close the garage.
The STATUS light of your GOGOGATE is blinking fast during 1-2 seconds when garage door opens or closes.
DOWNLOAD OUR FREE GOGOGATE APP ON YOUR SMARTPHONE OR IPAD .
You will find our APP at:
Apple products:
Look for the Apple store Icon on your iPhone or iPad and search for GOGOGATE
On Android:
Look for the Google Play Icon on your Android device and search for GOGOGATE
11
STEP 3: Program your GOGOGATE in 3 simple steps
Double click to open your app Press the settings button
(bottom right of screen)
Select
“BEGIN YOUR INSTALLATION”
12
COMPLETE THE FIELDS BELOW ON YOUR SMARTPHONE
:
We recomend Standard configuration.
Choose a name for your device like “My house”.
Choose a password (numbers only) up to 8 characters in length.
GoGoGate should automatically detect your network/SSID name. If not please input your current network/SSID name.
Input your existing home network password.
We have pre-selected WPA which is the most common used settings. You may want to try WEP if your installation fails.
Select “Open” if your home network is not password protected.
There is a 4 digit code on the front of your Wireless door sensor (included). This is your door sensor ID. Input code here.
GOGOGATE comes standard with 1 sensor. If you bought more sensors, you can input the codes of door 2 and 3.
Give your garage door a name. You can personalize it.
Press “Start” to begin programming the GoGogate Device
13
Press the start button when you have completed the above sections, and follow the instructions.
MAKE SURE YOUR SMARTPHONE IS CONNECTED
TO YOUR HOME NETWORK VIA WIFI.
Keep your phone placed on the GOGOGATE device
until you hear 3 beeps.
If you hear 1 long beep, this means that your programming failed.
Please try again
At that point you may remove your phone.
You are done.
WARNING: You have 5 seconds to place your phone on the GOGOGATE device. This will start your programing sequence.
During the programming of your GOGOGATE you will hear an automated voice saying “programming”, until the sequence is completed.
Upon successful completion of the programming sequence you will hear 3 beeps.
IN CASE OF PROBLEMS WITH YOUR EASY PROGRAMMING PLEASE
REFER TO PAGE 23.
14
You are all done!! It’s time to try it out. Your garage doors should now be displayed in green if they are connected and shaded if they are not connected.
(See drawing)
You may now press the garage door button on your Phone to open/close the garage.
THE BUTTONS ON YOUR SMARTPHONE APP MAY LOOK
LIKE ANY OF THE 4 BUTTONS DISPLAYED BELOW.
CONNECTED & CLOSED
Wireless Door Sensor assigned
If you have properly installed the wireless sensors on your garage door, you should see a red (locked sign) if your garage is closed or green (open sign) if garage door is open.
CONNECTED & OPEN
Wireless Door Sensor assigned
CONNECTED
No Wireless Door Sensor assigned
PLEASE NOTE: You may have to open and close your garage door via the
GOGOGATE
app “once” to synchronize the wireless sensors with the actual status of your garage door.
NOT CONNECTED
No Wireless Door Sensor assigned
15
ADVANCED INSTALLATION OPTION – Recommended for installers
Your GOGOGATE is capable of controlling many others devices such as electric blinds or sprinkler systems. Depending on the devices you are connecting you may need to choose the transmission mode suitable for that application. We recommend that this type of installation be completed by a professional installer.
GRG
This is the default Garage mode which enables you to open or close the garage door. One click on the garage 1 button and the output relay of G1 closes during 1 second. The relay will re-open after that delay.
PUL
The PULSE mode should be used to control things like electrical blinds. It allows for continuous control while a button is pressed. For example: If you press and hold the device 1 button to open your blinds, the output relay G1 will remain closed (and your blinds will continue to open) until the button is released. The same applies when you want to close your blinds. Press and hold the device 1 button. Release button to stop.
ON/OFF
The ON/OFF mode is made to activate things like exterior lights. Under this setting, if you press and release the device 1 button, the output relay G1 will remain closed.
(ie lights will go on). If you click another time the same button, output relay G1 will open (ie lights will turn off) .
PORT
By default, GOGOGATE uses port 8001, but, if you want to install more than one GOGOGATE in the same Network, you can choose another port.
The available ports are between 8001 and 65534.
IP SETTINGS
In advanced mode, you have to put a static IP for GOGOGATE, DHCP is disabled.
By default, in Standard settings, DHCP is enabled.
16
ADD MORE WIRELESS DOOR SENSORS TO YOUR GOGOGATE
If you decided later on to buy a few more door sensors, don’t worry. They are easy to configure.
Just follow the instructions below.
SELECT THE ADD SENSOR MENU SELECT THE ADD SENSOR MENU
Input here the 4 digit code found on the front of your
Wireless Sensors
Give your garage doors a
Name
Please note that if you had already programmed garage door 1 when you bought your GoGoGate and are now adding 1 or 2 more door sensors, you will need to re-enter the information (4 digit code and name) of your door sensor 1. Leaving any field BLANK is equivalent to ERASING your previous settings.
WARNING: After you press Start you have 5 seconds to place your phone on the GOGOGATE device. This will start your programming sequence. Keep your phone placed on the gogogate device until you hear 3 beeps. (if you hear 1 long beep, programming has failed. Please try again). At that point you may remove your phone. You are done.
17
CHANGE APP SETTINGS:
We know that with time things may change. The Change App Settings menu will give you the flexibility you need.
SELECT
“CHANGE APP SETTINGS”
Change your device or door name.
You should use this option if you bought a
2nd GOGOGATE device and installed it in another location (eg beach house).
This allows you to create another window to access the garages in your 2nd location.
You can access the other window by swapping your fingers on the main screen from right to left.
HOME BEACH
18
GUEST ACCESS APP:
Give access to your garage to a friend or relative
NOTE. To access your garage, your friends will have to:
1) Download the GOGOGATE app on the smartphone
2) They will need to have access to your home network via wifi
3) They will need your GOGOGATE name and password.
SELECT “GUEST ACCES” STANDARD MODE
19
REMOTE ACCESS:
Open your garage doors from anywhere in the world
NOTE: You can open/close your garage doors remotely while using your GoGoGate app on your Smartphone or from any computer. You need to have internet access to use this feature.
Press this button while connected to the internet to access
GOGOGATE WEB PAGE
Input your default password: admin
20
2
1
1
The Web Page will display the number of connected garage doors.
Important: For your own safety, you will ONLY be able to remotely operate garage doors that have connected door sensors.
All other doors will be shown as “grey buttons” even if they are actually connected to your
GoGoGate.
Pressing any connected button will open or close your garage doors.
You will see an open or closed sign indicating the status of your door.
4
3
2
This section shows you the current status of you doors and technical information you used to program your GoGogate device. By pressing any of these 3 config buttons you can change all the settings of your device.
Example: garage and device name, network name and password, etc..
3
By default the Remote access feature is disabled. You need to enable it first and agree with the terms and conditions of use. You only need to do this once!
4
Your default password is : Admin. We recommend you change
Immediately your default password.
21
4) Troubleshooting:
Having difficulties with your installation. See if the information below will help.
I can not program the GoGoGate
• Make sure your network name and password are correct. (password can be case sensitive)The WIFI
USB LED must be constantly blinking (ie with no pauses or interruptions). If this is not the case, you have entered the wrong WIFI Network name or password .
• Change the setting from WPA to WEP and restart the installation sequence
• Did you hear the 3 beeps after placing your phone on the GOGOGATE device? Moving your phone before the sound is heard will impact the programming. You may have to re-start your installation by pressing “begin your installation” and “start”.
• If you still cannot program your GoGoGate device after several attempts, you may want to refer to page
23 for an alternate way of programming your product. You can also call technical support at +1 855
4736765 or email us at [email protected]
My garage door does not open:
• Make sure the cables provided are connected properly on the back of your garage wall mount buttons
• Make sure that the green cable adapter is inserted properly on the gogogate cable slot.
I can not see if my garage door is open or closed
• Make sure you have installed the garage door sensors properly and according to the drawings provided
• Make sure you have taken the battery protector tape out off the device prior to attempting to program the garage door sensors
• Make sure you have entered the correct 4 digit code found on the front of the sensors when programming the app.
• Make sure your wireless sensors are within range. Range is approximately 150ft or 50m in open space.
Distance maybe reduced by interference or type of walls. Open or Close your garage door while looking at the STATUS LED on the GOGOGATE device. When you open/close your garage door the STATUS
LED LIGHT of the device should blink fast within 2 seconds.
Still having issues. No problem.
Watch our installation video at www.gogogate.com or contact us at:
[email protected]
22
FOLLOW INSTRUCTIONS BELOW ONLY IF YOUR GOGOGATE PROGRAMMING HAS FAILED.
Using your PC, you will need to gain access to the WEB page of your router. This is the web page you used to configure your router when you first installed it. You can find this information in your router user manual. The address is usually something like http://192.168.1.1
0. Under set up change the name of your NETWORK to: Connect
(Please make sure you have used a CAPITAL “C’ when writing connect)
1. Under “Wireless Security” change your Security settings to : Disabled or Open
2. Open your GoGoGate Smartphone app.
3. Go to “Change app Settings” and then “add another GoGoGate”
4. For GoGoGate name input : Home and for Password input: 12345678
5. Press Save
6. Go back to main screen on your Smartphone. Your garage door buttons should now show as “black
with green circles”
7. Press “Find GoGoGate “ at the bottom of your main Smartphone screen . (below garage buttons).
8. You will now be directed to your GoGoGate webpage.
9. Enter password: ADMIN
10. Choose CONFIG WIFI
11. Now enter the Security settings you had in step 1 (above)
12. Press next and enter the SSID name. This is the original network name you had given your
network in step 0.
13. Press update. NOTE: this maybe a good time to configure your garage doors if you have not done
so before. Go to CONFIG Doors (main page) Here you can enter the name of your doors and enter
the 4 digit code of each wireless door sensor. Remember to SAVE your settings .
14. Exit the GoGoGate web page
15. On your PC, go back to your router web page and re-enter your original Security settings and
Network name . (ie those entered in step 11 and 12)
You are done!! Your GoGogate device should now operate properly.
23
5) Limited warranty and return policy
The gogogate product comes with a one (1) year warranty against mechanical and electrical defects provided the products have been used in accordance with the documentation provided. The 1 year warranty period begins as of the purchase date by the user of the device. If customer does not have original proof of purchase, REMSOL will determine warranty eligibility via the manufacturing date.
If our product fails we will either 1) replace or repair your product or 2) decide to refund you the purchase price paid for the product and the foregoing will be the customer sole remedy for breach of this warranty. Products may be replaced by refurbished units or by different models of similar functionality. You also understand that above options will be implemented at the complete discretion of REMSOL LLC.
Our limited warranty is transferable from original customer to subsequent owner but the warranty period will not be extended in duration or coverage as a consequence of this transfer in ownership.
REMSOL assumes no warranty obligation with regards to a) normal wear and tear, b) products with no workmanship or product defects, c) misuse, abuse, negligence accidents, fraud, c) use of improper voltage (this is a low voltage device), d) acts of God, e) non authorized or non intended use of the product, f) consumable parts such as batteries.
•
•
Your Right to Return and Returns Policy
You may return purchased Products for any reason for a full refund of the Product purchase price actually paid within 15 working days following the date you receive the Products, subject to compliance with the following:
• You must obtain a REMSOL return reference number. This number may be obtained from REMSOL by calling us on designated telephone numbers mentioned on the REMSOL websites or by requesting the number via email: [email protected].
The REMSOL return reference number must be prominently displayed on the outside of the parcel in which the Products are returned.
Your REMSOL invoice must be enclosed with the returned Products. Products must be returned in the original packaging, in “as new condition”, and with all component products, parts, accessories, guarantee cards, manuals and other documents and items. Customer is expected to re-package the product properly in order to avoid damage during transportation and to ship the product to REMSOL at
Customer’s own cost.
If you return Products (1) which have been damaged or used, (2) after the 15 working days returns period (or other longer period specified by applicable law), (3) parts of which, including components, included products, accessories, packaging, boxes, documents and/or other items are damaged or missing, or (4) without pre-paid delivery, REMSOL retains the right either to refuse to refund Product purchase price (subject to applicable local law), or to charge you repair, restocking or related fees and delivery charges. REMSOL may in that case deduct those fees and charges from any payments to be refunded to you.
Please refer to our website for more detailed information on product warranty and returns.
24
•
•
•
•
•
•
Safety information
WARNING! ELECTRIC SHOCK HAZARD: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO WATER. Read and follow these instructions, heed all warnings, and keep this document for future reference,
•
•
•
•
•
•
•
•
Set up your product in accordance with REMSOL product documentation, and place your product in a stable location so it will not fall and cause product damage or bodily harm.
Do not use your product near water including dripping or splashing sources (e.g., indoor fountains), or near objects filled with liquids, such as flower vases or fish tanks.
Do not use your product near heat sources (eg, radiators. heat registers, stoves,open flames, such as lighted candles, brother heatproducing devices, such as audio amplifiers or TVs).
Do not, under any circumstance, modify your products power supply, if one has been included. lf the plug does not fit into yourAC outlet, have a certified electrician replace your obsolete AC outlet.
The AC outlet (receptacle) should be near the product and easily accessible.
Refer all servicing and repair to qualified service personnel. Servicing is required when your product does not operate normally or the power cord/plug has been damaged, the product has been exposed to water rain, liquid, or moisture, the product has been dropped, or an object has been inserted into a product port or vent.
For portable products or products weighing less than 7 kg (15 lbs), the product label may be found on the product stand, under a lid, or on the bottom of the product itself.
Clean your product using only a dry cloth and no water or liquid.
Power supply warning:
Caution electric shock/tire hazard! For indoor use only. Do not expose to moisture, Liquid, or heat. Do not use any other power supply with your product.
Install the wires connecting to your garage door wall buttons with all equipment powered off (garage door opener and gogogate).
Please read carefully all these instructions before installing and starting to use GoGogate.
Please follow all the instructions in detail in order to avoid personal injuries or damage to third party devices.
The gogogate is not adequate for really sensible installations or to control very precise products or processes.
Failure of the WI-FI network or a power failure will affect control and functionality of the device.
The gogogate must not be used for medical applications or in any location where explosive materials are located.
•
•
•
•
FCC Statements
This device complies with Partl5 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
25
WARNING: Where shielded interface cables or accessories have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC.
Changes or modifications to product not expressly approved by REMSOL could void your right to use or operate your product.
Canada I IC Statement:
This Class B digital apparatus complies with Canadian ICES-003. (Cet appareil numerique de categorie B est conforme a la norme canadienne ICES-O03.)
•
•
This device complies with lndustry Canada licence-exempt RSS standard 2IO.
Operation is subject to the following two conditions: (l) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
•
•
•
•
(Ce dispositif est conforme a la norme CNR-210 d’lndustrie Canada applicable aux appareils radio exempts de licence,. Son exploitation est autorisee aux deux conditions suivantes (I) le dispositif ne doit pas produire de brouillage prejudicable, et (2) ce dispositive doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.) exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.
Safety Precautions
This product has been designed with the highest concern for safety. However, any electrical device, if used improperly, has the potential for causing fire, electrical shock or personal injury. To help ensure accident-free operation, follow these guidelines:
Observe all warnings, precautions and instructions.
Regularly inspect the AC power adapter for damage.
Stop use, unplug the AC power adapter from the electrical outlet and disconnect any other cables immediately if the device functions in an abnormal manner produces unusual sounds or smells or becomes too hot to touch,
For more information on product safety and troubleshooting, please go to www.gogogate.com/support.
CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions
•
•
•
•
Use and Handling
• Do not touch the Player or connected cables during an electrical storm.
Do not allow liquid, small particles or other foreign objects to get into the device or accessories.
Do not expose the device to smoke or steam.
Do not expose the device or accessories to high, temperatures, high humidity or direct sunlight.
Do not place the device on the floor or in a place Where they may cause someone to trip or stumble.
WWW.GOGOGATE.COM
