Panasonic 7160-0348 Specification

INSTALLATION INSTRUCTIONS

Product

Panasonic CFH2 Vehicle Docking Station

7160-0348

Revision

Rev. A

Form

INST-548

Printing Spec: PS-001

This instruction sheet is for the Gamber-Johnson Panasonic

Toughbook CFH2 Vehicle Docking Station

Gamber-Johnson Part Number: 7160-0348

*These instructions are for the docking station only. For instructions on features, set-up and operation of the

Toughbook CFH2 computer, please refer to the manuals provided by Panasonic with the computer.

IMPORTANT SAFETY INFORMATION for

INSTALLERS

Safety is dependent on the proper installation and servicing of this docking station. It is important to read and follow all instructions before installing this product.

To properly install a Gamber-Johnson docking station you must have a good understanding of electrical procedures and systems, along with proficiency in the installation and service of electrical and/or computer equipment.

There are no adjustments required at any time of the electrical components within the docking station. Opening the docking station housing will void the product warranty.

Panasonic recommends using a Lind Auto Adapter to power the docking station. It can be ordered from Gamber-Johnson (Item No. 11798)

Keep foreign objects away from the Expansion Bus on the docking station.

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© copyright 2009 Gamber-Johnson, LLC

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

1 of 6

Components

Front View

Actuator Button

Lock (Optional)

Latching

Mechanism

Bottom View

External Display Port

MINI DSUB 15-PIN Female

Expansion Bus

FIG. A

DC-IN Jack

DC IN 16V

Serial Port

DSUB 9-PIN Male

Will not support serial mouse.

USB Ports (3 ports)

(4 PIN, USB2.0)

FIG. B

LAN Port

IEEE 802.3 10Base-T / IEEE 802.3u

100Base-TX

2 of 6

Installation Recommendations

Conduct a "Bench Test"

Gamber-Johnson strongly advises a "bench test" be conducted to verify that all electronic and software issues are resolved prior to installation:

1. Make sure computer is operational by itself.

2. Insert computer into docking station and verify that the display is operating in the

dock.

3. Interconnect entire assembly and verify start-up of all components, including other

equipment (printers, modems, scanners, etc.).

Attaching Strain Relief Bracket

A cable Strain Relief Bracket is provided in the hardware bag. This bracket will provide a mounting platform to secure all interface cables. It is recomended that all cables are secured to the Strain Relief Bracket.

1. Lay docking station on its front face to expose rear mounting

surface

2. Align the Strain Relief Bracket mounting holes with the two

holes in the metal housing on the bottom of the docking

station (FIG C).

3. Using a #2 Phillips Srew Driver secure the Strain Relief

Bracket using the two #8-32 X.25 Screws and split lock

washers provided in the hardware bag.

Metal Housing

FIG. C

Strain Relief

Bracket

#8-32unc Mounting Screws and Lock Washers

3 of 6

Mounting

The docking station can be mounted to any 75mm VESA hole pattern, or to the following

Gamber-Johnson products:

- VESA Adaptor Bracket (7160-0206)

- Wall Mount Bracket (7160-0195)

Connecting Peripherals

Ensure that all wires have strain relief protection. Strain relief is accomplished by attaching the cables to the Strain Relief Bracket. Cable ties and cable tie holders are provided in the hardware bag. Press the cable tie holders into the holes in the strain relief bracket where needed. Restrain the periferal cables to the cable tie holders and to the USB support brackets (installed by factory) with the cable ties provided. Loosen the power plug restraint and attach the power cable to the docking station. Slide the power plug restraint up tight to the bottom side of the power cable and tighted the mounting screw to hold in place. To assure compliance with FCC, Part 15, Class B rules, only use shielded interface cables when connecting peripherals.

FIG. D

Cable Ties

Cable Tie

Holders

Power

Cable

Strain Relief

Bracket

USB Support

Bracket

Power Plug

Restraint

Power Plug

Mounting Screw

4 of 6

Inserting Computer Into Docking Station

CAUTION:

Turn computer power OFF when inserting and removing computer from docking station

1. Turn computer power OFF.

2. Insert bottom of computer into docking station (FIG G).

3. Push the top of computer back into the docking

station until an audible "click" is heard and the

computer is secured by the Latching Mechanism (FIG H).

4. (Optional) The Key Lock can now be used for

security purposes.

FIG. G

FIG. H

5 of 6

Removing Computer From Docking Station

1. Turn computer power OFF.

2. If docking station is locked, unlock using the key provided.

3. Grasp the computer handle and press the Actuator Button in and down with the palm of your hand. (FIG I).

4. Pull the computer towards you to remove from docking station (FIG J).

Actuator Button

FIG. I

FIG. J

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© copyright 2009 Gamber-Johnson, LLC

6 of 6