The Beltpack
Quick Reference Guide
BP410
Beltpack Setup
Battery RELEASE BATTERY button
1 2 4 3 5 6
Belt clip
7 8 9 10 7
1. Battery
2. Increase Volume button ( ▲ )
3. Decrease Volume button ( ▼ )
4. PWR (Power) button
5. Headset cable connector
6. Battery-release latch
7. Power/Mode lights
8. Channel A (Intercom 1) button - Includes 2-wire and
4-wire connections
9. ISO (Isolate) button - To All Wireless Headsets and
Beltpacks, Base, ISO Relay and AUX OUT
(if activated)
10. Channel B (Intercom 2) button - Includes 2-wire and 4-wire connections
Headset cable plug
¾ Insert a fully charged battery in each Beltpack with the metal contacts inserted first. Slide it in until it snaps.
NOTE: The battery will not slide in if inserted incorrectly. Excessive force should not be necessary.
¾ Plug the Beltpack’s headset cable connector into each
Beltpack.
BP410 Beltpack Settings
To Set:
ISO restrict On
ISO restrict Off
Handsfree On selected button(s)
Handsfree Off selected button(s)
Listen-Only mode On
Listen-Only mode Off
All functions are from an off state. Press the Power button and release with the appropriate buttons below.
A button
A button and ISO buttons
A button and/or B button and/or ISO and Volume up button (▲)
A button and/or B button and/or ISO and Volume down button (▼)
Volume down button (▼)
Volume up button (▲)
To Set:
Increase mic gain (15 steps)
Decrease mic gain (15 steps)
Increase sidetone level (5 steps)
Decrease sidetone level (5 steps)
With the power already on...
Press the B button while repeatedly pressing the Volume up button (▲)
Press the B button while repeatedly pressing the Volume down button (▼)
Press the A button while repeatedly pressing the Volume up button (▲)
Press the A button while repeatedly pressing the Volume down button (▼)
Copyright © 2016 Clear-Com, LLC, an HM Electronics, Inc. company. All rights reserved.
Clear-Com, the Clear-Com logo and Clear-Com Concert are trademarks or registered trademarks of HM Electronics, Inc.
Part Number: 399G214 Rev A
Date: 12/5/16
General Use
Beltpack Sidetone Adjustment:
¾ Press and hold the A button while you repeatedly press up (▲) to increase or press down (▼) to decrease audio levels.
Changing the battery:
¾ When a Beltpack battery becomes weak, a headset voice prompt will say “Change battery.”
¾ Press the RELEASE BATTERY button on the belt clip of the pouch, and use your thumb to slide the battery from the belt-pac.
¾ When charging the battery using the AC50 Battery Charger, the charging time is about 2.5 hours.
The DX410 Console
Beltpack
Registration
Power Switch
Audio Channel and
Auto-Null Controls
Local Headset
Controls
STATUS REG AUTO NULL
Register Beltpack
¾ Make certain the Beltpack is turned Off.
¾ Press REG button on base station.
– STATUS display on the base station shows “ o” for registration mode.
¾ On the Beltpack, press and hold ISO while pressing POWER and then release all buttons.
– The power lights blink red, then green and then turn off. One power light remains green.
– The registration number will appear on the base station STATUS display.
AUTO NULL Adjustment (only if using 2-wire interface)
If echo is heard in wireless Beltpacks on A or B:
¾ Use pointed object (e.g. pen) to press and hold the A or B AUTO NULL button for 2 seconds.
CAUTION: Before pressing an AUTO NULL button, be certain there are no open microphones on the wired system. Notify wired system users that a loud noise may occur in their headsets during the auto null adjustment.
The system may be out of operation for approximately 50 seconds during this adjustment.
Local Headset Communication
¾ SEL button selects communication with A, B or ISO.
– A, B or ISO lights indicate selection.
¾ TALK button
– Press and release quickly to “latch on” for open communication.
– Press and hold while talking for momentary communication – release when finished.
¾ VOLUME control adjusts the audio level in local headset ear piece.
¾ MIC LEVEL control adjusts the audio level going out from local headset microphone.
Technical Support
In The Americas and Asia – Tel: +1.510.337.6600 or 1.800.462.4357 Menu option 1 • Hours: 8:00am-5:00pm Pacific Time • Web: www.clearcom.com
In Europe, Middle East and Africa – Tel: +44.1223.815000 • Hours: 8:00am-5:00pm GMT • Email: [email protected]
