Gigabyte GA-H61M-D2H-USB3 motherboard User's manual
Gigabyte GA-H61M-D2H-USB3 is a motherboard designed for use with Intel Core i7/i5/i3 processors. It supports dual-channel DDR3 memory, and features two PCI Express x16 slots, two PCI Express x1 slots, and two PCI slots. The board also includes an integrated graphics controller, as well as Realtek Gigabit Ethernet and 8-channel audio. With its wide range of features, the Gigabyte GA-H61M-D2H-USB3 is a great choice for building a budget-friendly gaming or multimedia PC.
Advertisement
Advertisement
User's Manual
Rev. 1002
12ME-H61MD2H-1002R
Copyright
© 2011 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.
In order to assist in the use of this product, carefully read the User's Manual.
For product-related information, check on our website at: http://www.gigabyte.com
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.
Example:
Table of Contents
GA-H61M-D2H/GA-H61M-D2H-USB3 Motherboard Layout ..........................................5
GA-H61M-D2H/GA-H61M-D2H-USB3 Motherboard Block Diagram .............................6
- 4 -
GA-H61M-D2H/GA-H61M-D2H-USB3 Motherboard Layout
KB_MS
ATX_12V
LGA1155
HDMI
R_USBj
R_USB30k
ATX
USB_LAN CPU_FAN
AUDIO
Atheros/
Realtek
GbE LAN
Etron
EJ168k
PCIEX16
PCI1
BAT
GA-H61M-D2H/GA-H61M-D2H-USB3 iTE
IT8728
PCI2
CODEC
F_AUDIO
PCIEX1
LPT COMA
PCIe to PCI
Bridge
F_USB2
Intel ®
F_USB1
H61
CLR_CMOS
SATA2
M_BIOS
B_BIOS
1 0
3 2
SYS_FAN
F_PANEL
Box Contents
GA-H61M-D2H or GA-H61M-D2H-USB3 motherboard
Motherboard driver disk
User's Manual
Two SATA cables
I/O Shield
The box contents above are for reference only and the actual items shall depend on the product package you obtain.
j Only for GA-H61M-D2H.
k Only for GA-H61M-D2H-USB3.
- 5 -
GA-H61M-D2H/GA-H61M-D2H-USB3 Motherboard Block Diagram
PCIe CLK
(100 MHz)
LGA1155
CPU
CPU CLK+/- (100 MHz)
DDR3 1333/1066/800 MHz
Dual Channel Memory
PCI Express Bus x16
1 PCI Express x1 HDMI
D-Sub
DVI-D
PCI Express Bus x1
Etron
EJ168k x1 x1
Atheros/
Realtek
GbE LAN
2 USB 3.0/2.0k
RJ45
LAN x1
PCIe to PCI
Bridge
PCI Bus
Intel ® H61
CODEC
Dual BIOS
LPC
Bus iTE
IT8728
4 SATA 3Gb/s
8 USB 2.0/1.1j
6 USB 2.0/1.1k
LPT
COM Port
PS/2 KB/Mouse
2 PCI
PCI CLK
(33 MHz)
j Only for GA-H61M-D2H.
k Only for GA-H61M-D2H-USB3.
- 6 -
Chapter 1 Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.
•
•
Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.
•
•
•
•
When handling the motherboard, avoid touching any metal leads or connectors.
It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.
Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.
Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.
•
•
•
•
•
•
•
•
Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.
Before using the product, please verify that all cables and power connectors of your hardware components are connected.
To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.
Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.
Do not place the computer system on an uneven surface .
Do not place the computer system in a high-temperature environment.
Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.
If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.
- 7 -
1-2 Product Specifications
CPU
Chipset
Memory
Onboard
Graphics
Audio
LAN
Expansion Slots
USB
Internal
Connectors
Storage Interface
Support for Intel ® Core ™ i7 processors/Intel ® Core ™ i5 processors/
Intel ® Core ™ i3 processors/Intel ® Pentium ® processors/Intel ® Celeron ® processors in the LGA1155 package
(Go to GIGABYTE's website for the latest CPU support list.)
L3 cache varies with CPU
Intel
®
H61 Express Chipset
4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory
* Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB.
Dual channel memory architecture
Support for DDR3 1333/1066/800 MHz memory modules
Support for non-ECC memory modules
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
Integrated Graphics Processor:
- 1 x D-Sub port
- 1 x DVI-D port, supporting a maximum resolution of 1920x1200
* The DVI-D port does not support D-Sub connection by adapter.
- 1 x HDMI port, supporting a maximum resolution of 1920x1200
Realtek/VIA HD audio codec
High Definition Audio
2/4/5.1/7.1-channel
* To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.
1 x Atheros GbE LAN chip (10/100/1000 Mbit)
1 x PCI Express x16 slot, running at x16
1 x PCI Express x1 slot
(All PCI Express slots conform to PCI Express 2.0 standard.)
2 x PCI slots
Chipset:
- 4 x SATA 3Gb/s connectors supporting up to 4 SATA 3Gb/s devices
Chipset:
- Up to 8 USB 2.0/1.1 ports (4 ports on the back panel, 4 ports available through the internal USB headers) j
- Up to 6 USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through the internal USB headers) k
Etron EJ168 chip: k
- Up to 2 USB 3.0/2.0 ports on the back panel
1 x 24-pin ATX main power connector
1 x 4-pin ATX 12V power connector
4 x SATA 3Gb/s connectors
1 x CPU fan header
j Only for GA-H61M-D2H.
k Only for GA-H61M-D2H-USB3.
- 8 -
Internal
Connectors
Back Panel
Connectors
I/O Controller
Hardware
Monitor
BIOS
Unique Features
1 x system fan header
1 x front panel header
1 x front panel audio header
2 x USB 2.0/1.1 headers
1 x parallel port header
1 x serial port header
1 x Clear CMOS jumper
1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x D-Sub port
1 x DVI-D port
1 x HDMI port
4 x USB 2.0/1.1 ports j
2 x USB 2.0/1.1 ports k
2 x USB 3.0/2.0 ports k
1 x RJ-45 port
3 x audio jacks (Line In/Line Out/Microphone) iTE IT8728 chip
System voltage detection
CPU/System temperature detection
CPU/System fan speed detection
CPU/system fan speed control
* Whether the CPU/system fan speed control function is supported will depend on the CPU/system cooler you install.
2 x 32 Mbit flash
Use of licensed AWARD BIOS
Support for DualBIOS
™
PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b
Support for @BIOS
Support for Q-Flash
Support for Xpress BIOS Rescue
Support for Download Center
Support for Xpress Install
Support for Xpress Recovery2
Support for EasyTune
* Available functions in EasyTune may differ by motherboard model.
Support for Smart 6
™
Support for Auto Green
Support for ON/OFF Charge
Support for Cloud OC
Support for 3TB+ Unlock
Support for TouchBIOS
Support for Q-Share
j Only for GA-H61M-D2H.
k Only for GA-H61M-D2H-USB3.
- 9 -
Bundled
Software
Operating
System
Form Factor
Norton Internet Security (OEM version)
Support for Microsoft
®
Windows 7/Vista/XP
Micro ATX Form Factor; 24.4cm x 22.5cm
* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.
1-3 Installing the CPU
•
•
Read the following guidelines before you begin to install the CPU:
• Make sure that the motherboard supports the CPU.
•
(Go to GIGABYTE's website for the latest CPU support list.)
Always turn off the computer and unplug the power cord from the power outlet before installing
• the CPU to prevent hardware damage.
Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
Apply an even and thin layer of thermal grease on the surface of the CPU.
Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage of the CPU may occur.
• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.
Installing the CPU
A. Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.
LGA1155 CPU Socket
Alignment Key Alignment Key
Pin One Corner of the CPU Socket
LGA1155 CPU
Notch Notch
Triangle Pin One Marking on the CPU
- 10 -
1-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
•
•
• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.
Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration
This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory.
Enabling Dual Channel memory mode will double the original memory bandwidth.
The four DDR3 memory sockets are divided into two channels and each channel has one memory socket as following:
Channel A: DDR3_1, DDR3_2
Channel B: DDR3_3, DDR3_4
Dual Channel Memory Configurations Table
Two Modules
Four Modules
DDR3_1 DDR3_2 DDR3_3 DDR3_4
DS/SS - DS/SS - -
- DS - DS
SS SS SS SS
(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)
Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1.
2.
Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.
When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance.
•
• If one or two single-sided memory modules are to be installed, be sure to install it/them in the DDR3_1 socket or/and the DDR3_3 socket. If three single-sided memory modules are to be installed, two of them must be installed in the DDR3_1 and DDR3_3 sockets. Due to a hardware limitation, if you have already installed two double-sided memory modules, any additional memory module will not be supported.
If four DDR3 1333 MHz memory modules are installed, the maximum memory speed will be limited to
1066 MHz.
1-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
• Make sure the motherboard supports the expansion card. Carefully read the manual that came
• with your expansion card.
Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.
- 11 -
1-6 Back Panel Connectors
j
k
PS/2 Keyboard and PS/2 Mouse Port
Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector. Connect a monitor that supports D-Sub connection to this port.
DVI-D Port (Note)
The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
DVI-D connection to this port.
HDMI Port
HDMI (High-Definition Multimedia Interface) is an all-digital audio/video interface capable of transmitting uncompressed audio/video signals. The HDMI port is HDCP compliant and supports Dolby TrueHD and DTS HD Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio output.
You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is
1920x1200, but the actual resolutions supported are dependent on the monitor being used.
After installing the HDMI device, make sure the default device for sound playback is the HDMI device. (The item name may differ from operating system. Refer to the figure below for details.)
In Windows 7, select Start>Control Panel>Hardware and
Sound>Sound>Playback, set Intel(R) Display Audio to the default playback device.
j Only for GA-H61M-D2H.
k Only for GA-H61M-D2H-USB3.
(Note) The DVI-D port does not support D-Sub connection by adapter.
- 12 -
USB 2.0/1.1 Port
The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
USB 3.0/2.0 Port k
The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification.
Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.
Connection/
Speed LED Activity LED
LAN Port
Connection/Speed LED:
State Description
Orange 1 Gbps data rate
Green 100 Mbps data rate
Off 10 Mbps data rate
Activity LED:
State Description
Blinking Data transmission or receiving is occurring
Off No data transmission or receiving is occurring
Line In Jack (Blue)
The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.
Mic In Jack (Pink)
The default Mic in jack. Microphones must be connected to this jack.
To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.
k Only for GA-H61M-D2H-USB3.
•
•
When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.
- 13 -
1-7 Internal Connectors
1 3
12
1) ATX_12V
2) ATX
3) CPU_FAN
4) SYS_FAN
5) SATA2 0/1/2/3
6) F_PANEL
7 10 9 8 11 6
7) F_AUDIO
8) F_USB1/2
9) COMA
10) LPT
11) CLR_CMOS
12) BAT
2
5
4
•
•
Read the following guidelines before connecting external devices:
First make sure your devices are compliant with the connectors you wish to connect.
Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.
• After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.
- 14 -
1/2) ATX_12V/ATX (2x2 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design.
Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.
2
4
ATX_12V
1
3
ATX_12V:
Pin No. Definition
1
2
3
4
GND
GND
+12V
+12V
12
1
ATX
24
13
7
8
9
5
6
ATX:
Pin No. Definition
1
2
3
4
10
11
12
3.3V
3.3V
GND
+5V
GND
+5V
GND
Power Good
5VSB (stand by +5V)
+12V 22
+12V (Only for 2x12-pin ATX) 23
3.3V (Only for 2x12-pin ATX) 24
19
20
21
Pin No. Definition
13 3.3V
14
15
16
17
18
-12V
GND
PS_ON (soft On/Off)
GND
GND
GND
-5V
+5V
+5V
+5V (Only for 2x12-pin ATX)
GND (Only for 2x12-pin ATX)
- 15 -
DEBUG
PORT
G.QBOFM
3/4) CPU_FAN/SYS_FAN (Fan Headers)
The motherboard has a 4-pin CPU fan header (CPU_FAN) and a 4-pin system fan header (SYS_FAN).
Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.
1
CPU_FAN
CPU_FAN:
Pin No. Definition
1 GND
2
3
4
+12V
Sense
Speed Control
SYS_FAN
1
SYS_FAN:
Pin No. Definition
1 GND
2
3
4
+12V
Sense
Reserve
DEBUG
PORT
DEBUG
PORT
DEBUG
PORT
DEBUG
PORT
•
•
Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.
These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.
5) SATA2 0/1/2/3 (SATA 3Gb/s Connectors)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.
Each SATA connector supports a single SATA device.
7 7
6
7
4
5
Pin No. Definition
1
2
3
GND
TXP
TXN
GND
RXN
RXP
GND
1 1
1 0
3 2
Please connect the L-shaped end of the SATA cable to your SATA hard drive.
- 16 -
DEBUG
PORT
DEBUG
PORT
G.QBOFM
G.QBOFM
F_USB30
TPM w/housing
6) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
Message/Power/
Sleep LED
Power
Switch Speaker
F_AUDIO(H) F_PANEL(NH)
2
1
20
19
F_PANEL
(H61M-D2)
Hard Drive
Activity LED
Reset
Switch
Power LED
Chassis Intrusion
Header
DB_PORT
• MSG/PWR (Message/Power/Sleep LED):
System Status LED
S0 On
Connects to the power status indicator on the chassis front panel. The
LED is on when the system is operating. The LED keeps blinking when the
S1
S3/S4/S5
Blinking
Off
1 sleep state or powered off (S5).
• PW (Power Switch):
Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management Setup," for more information).
PWM Switch (X58A-OC)
3 12
ACPI_CPT
(GA-IVB)
• SPEAK (Speaker):
DIP
SMB_CPT
(GA-IVB)
PCIe power connector (SATA)(X58A-OC)
• HD (Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
• is reading or writing data.
RES (Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.
CLR_CMOS
CI
DIS_ME
GP15_CPT
(GA-IVB)
• (Chassis Intrusion Header):
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor.
XDP_CPU
XDP_PCH
(GA-IVB)
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.
- 17 -
PWM Switch (SW1)(X79-UD7)
5 4 3 2 1
DIP
BIOS_PH
(GA-IVB)
7) F_AUDIO (Front Panel Audio Header)
The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.
9
10
1
2
For HD Front Panel Audio: For AC'97 Front Panel Audio:
Pin No. Definition Pin No. Definition
1 MIC2_L 1 MIC
4
5
2
3
GND
MIC2_R
-ACZ_DET
LINE2_R
2
3
4
5
GND
MIC Power
NC
Line Out (R)
6
7
8
9
10
GND
FAUDIO_JD
No Pin
LINE2_L
GND
6
7
8
9
10
NC
NC
No Pin
Line Out (L)
NC
•
•
• The front panel audio header supports HD audio by default.
Audio signals will be present on both of the front and back panel audio connections simultaneously.
Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.
8) F_USB1/2 (USB 2.0/1.1 Headers)
The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.
9
10
1
2
Pin No. Definition
1 Power (5V)
2 Power (5V)
5
6
3
4
7
8
9
10
USB DX-
USB DY-
USB DX+
USB DY+
GND
GND
No Pin
NC
•
• Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header.
Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.
- 18 -
9) COMA (Serial Port Header)
The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer.
9
10
1
2
8
9
10
5
6
7
Pin No. Definition
1
2
NDCD-
NSIN
3
4
NSOUT
NDTR-
GND
NDSR-
NRTS-
NCTS-
NRI-
No Pin
DEBUG
PORT
10) LPT (Parallel Port Header)
The LPT header can provide one parallel port via an optional LPT port cable. For purchasing the optional
LPT port cable, please contact the local dealer.
25
26
1
2
Pin No. Definition
6
7
4
5
8
9
1
2
3
10
11
12
13
STB-
AFD-
PD0
ERR-
PD1
INIT-
PD2
SLIN-
PD3
GND
PD4
GND
PD5
Pin No. Definition
14 GND
15 PD6
16 GND
17 PD7
18 GND
19 ACK-
20 GND
21 BUSY
22 GND
23 PE
24 No Pin
25 SLCT
26 GND
- 19 -
G.QBOFM
11) CLR_CMOS (Clear CMOS Jumper)
Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the
CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.
Open: Normal
Short: Clear CMOS Values
•
•
Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.
After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).
12) BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.
•
•
•
•
•
You may clear the CMOS values by removing the battery:
1.
2.
3.
4.
Turn off your computer and unplug the power cord.
Gently remove the battery from the battery holder and wait for one minute.
(Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.)
Replace the battery.
Plug in the power cord and restart your computer.
Always turn off your computer and unplug the power cord before replacing the battery.
Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model.
Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model.
When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery (the positive side should face up).
Used batteries must be handled in accordance with local environmental regulations.
- 20 -
Chapter 2 BIOS Setup
To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.
To see more advanced BIOS Setup menu options, you can press <Ctrl> + <F1> in the main menu of the
BIOS Setup program.
To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
•
•
Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
@BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the
Internet and updates the BIOS.
•
•
Because BIOS flashing is potentially risky, if you do not encounter problems using the current version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing may result in system malfunction.
It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
(Refer to the "Load Optimized Defaults" section in this chapter or introductions of the battery/ clearing CMOS jumper in Chapter 1 for how to clear the CMOS values.)
2-1 Startup Screen
The following screens may appear when the computer boots.
A. The LOGO Screen (Default):
Function Keys
B. The POST Screen
Motherboard Model
BIOS Version
Award Modular BIOS v6.00PG
Copyright (C) 1984-2011, Award Software, Inc.
.
.
.
.
H61M-D2H E6
<DEL>: BIOS Setup <F9>: XpressRecovery2 <F12>: Boot Menu <End>: Qflash
08/19/2011-H61-7A89XG0AC-00
Function Keys
- 21 -
2-2 The Main Menu
Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use arrow keys to move among the items and press <Enter> to accept or enter a sub-menu.
(Sample BIOS Version: GA-H61M-D2H E6)
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit
F8: Q-Flash
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
: Select Item
F10: Save & Exit Setup
Change CPU's Clock & Voltage
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
•
•
•
If you do not find the settings you want in the Main Menu or a submenu, press <Ctrl>+<F1> to access more advanced options.
When the system is not stable as usual, select the system to its defaults.
Load Optimized Defaults item to set your
The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.
The Functions of the <F11> and <F12> keys (For the Main Menu Only)
F11: Save CMOS to BIOS
This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles
(Profile 1-8) and name each profile. First enter the profile name (to erase the default profile name, use the SPACE key) and then press <Enter> to complete.
F12: Load CMOS from BIOS
If your system becomes unstable and you have loaded the BIOS default settings, you can use this function to load the BIOS settings from a profile created before, without the hassles of reconfiguring the
BIOS settings. First select the profile you wish to load, then press <Enter> to complete.
- 22 -
2-3 MB Intelligent Tweaker(M.I.T.)
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
MB Intelligent Tweaker(M.I.T.)
M.I.T Current Status
Advanced Frequency Settings
Advanced Memory Settings
Advanced Voltage Settings
Miscellaneous Settings
[Press Enter]
[Press Enter]
[Press Enter]
[Press Enter]
[Press Enter]
Item Help
Menu Level
BIOS Version
BCLK
CPU Frequency
Memory Frequency
Total Memory Size
CPU Temperature
Vcore
DRAM Voltage
: Move Enter: Select
F5: Previous Values
E6
99.80 MHz
3193.73 MHz
1330.76 MHz
1024 MB
36 o C
1.188 V
1.584 V
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall system configurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory and reduce the useful life of these components. This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings may result in system's failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
MB Intelligent Tweaker(M.I.T.)
M.I.T Current Status
Advanced Frequency Settings
Advanced Memory Settings
Advanced Voltage Settings
Miscellaneous Settings
[Press Enter]
[Press Enter]
[Press Enter]
[Press Enter]
[Press Enter]
Item Help
Menu Level
BIOS Version
BCLK
CPU Frequency
Memory Frequency
Total Memory Size
CPU Temperature
Vcore
DRAM Voltage
: Move Enter: Select
F5: Previous Values
E6
99.80 MHz
3193.73 MHz
1330.76 MHz
1024 MB
36 o C
1.188 V
1.584 V
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency, total memory size , CPU temperature, Vcore, and memory voltage.
- 23 -
M.I.T. Current Status
This screen provides information on CPU/memory frequencies/parameters.
Advanced Frequency Settings
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Advanced Frequency Settings
CPU Clock Ratio
CPU Frequency
Advanced CPU Core Features
>>>>> Standard Clock Control
BCLK/DMI/PEG Clock Control x BCLK/DMI/PEG Frequency(0.1MHz)
System Memory Multiplier
Memory Frequency (Mhz)
Internal Graphics Clock
[31X]
3.10GHz (100x31)
[Press Enter]
(SPD)
1333
1100
[Disabled]
1000
[Auto]
1333
[Auto]
100.0MHz
Item Help
Menu Level
: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
Advanced CPU Core Features
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Advanced CPU Core Features
CPU Clock Ratio
CPU Frequency
Intel(R) Turbo Boost Tech.
(Note)
-Turbo Ratio(1-Core) (Note)
-Turbo Ratio(2-Core) (Note)
-Turbo Ratio(3-Core) (Note)
-Turbo Ratio(4-Core) (Note)
-Turbo Power Limit(Watts)
-Core Current Limit(Amps)
CPU Cores Enabled (Note)
CPU Multi-Threading (Note)
CPU Enhanced Halt (C1E) (Note)
C3/C6 State Support
CPU EIST Function
(Note)
CPU Thermal Monitor (Note)
(Note)
Bi-Directional PROCHOT (Note)
[31X]
3.10GHz (100x31)
[Auto]
34 Auto
33 Auto
33 Auto
32 Auto
95 [Auto]
97 [Auto]
[All]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
Item Help
Menu Level
: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
CPU Clock Ratio
Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU being installed.
CPU Frequency
Displays the current operating CPU frequency.
(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website.
- 24 -
Intel(R) Turbo Boost Tech. (Note)
Allows you to determine whether to enable the Intel CPU Turbo Boost technology. Auto lets the BIOS automatically configure this setting. (Default: Auto)
Turbo Ratio (1-Core)/(2-Core)/(3-Core)/(4-Core) (Note)
Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios according to the CPU specifications. (Default: Auto)
Turbo Power Limit (Watts)
Allows you to set a power limit for CPU Turbo mode. When the CPU power consumption exceeds the specified power limit, the CPU will automatically reduce the core frequency in order to reduce the power.
Auto sets the power limit according to the CPU specifications. (Default: Auto)
Core Current Limit (Amps)
Allows you to set a current limit for CPU Turbo mode. When the CPU current exceeds the specified current limit, the CPU will automatically reduce the core frequency in order to reduce the current.
Auto sets the current limit according to the CPU specifications. (Default: Auto)
CPU Cores Enabled (Note)
Allows you to determine whether to enable all CPU cores.
All Enables all CPU cores. (Default)
1 Enables only one CPU core.
2 Enables only two CPU cores.
3 Enables only three CPU cores.
CPU Multi-Threading (Note)
Allows you to determine whether to enable multi-threading technology when using an Intel CPU that supports this function. This feature only works for operating systems that support multi-processor mode.
(Default: Enabled)
CPU Enhanced Halt (C1E) (Note)
Enables or disables Intel CPU Enhanced Halt (C1E) function, a CPU power-saving function in system halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption. Auto lets the BIOS automatically configure this setting. (Default: Auto)
C3/C6 State Support (Note)
Allows you to determine whether to let the CPU enter C3/C6 mode in system halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption. The C3/C6 state is a more enhanced power-saving state than C1. Auto lets the BIOS automatically configure this setting. (Default: Auto)
CPU Thermal Monitor (Note)
Enables or disables Intel CPU Thermal Monitor function, a CPU overheating protection function. When enabled, the CPU core frequency and voltage will be reduced when the CPU is overheated. Auto lets the BIOS automatically configure this setting. (Default: Auto)
CPU EIST Function (Note)
Enables or disables Enhanced Intel SpeedStep Technology (EIST). Depending on CPU loading, Intel
EIST technology can dynamically and effectively lower the CPU voltage and core frequency to decrease average power consumption and heat production. Auto lets the BIOS automatically configure this setting. (Default: Auto)
(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website.
- 25 -
Bi-Directional PROCHOT (Note)
Auto Lets the BIOS automatically configure this setting. (Default)
Enabled When the CPU or chipset detects that an overheating is occurring, PROCHOT signals will be emitted to lower CPU performance to decrease heat production.
Disabled Only allows the CPU to detect whether an overheating is occurring to emit PRO-
CHOT signals.
>>>>> Standard Clock Control
BCLK/DMI/PEG Clock Control
Enables or disables the control of CPU base clock and DMI/PCIe bus frequency. Enabled will allow the
BCLK/DMI/PEG Frequency(0.1MHz) item below to be configurable. Note: If your system fails to boot after overclocking, please wait for 20 seconds to allow for automated system reboot, or clear the CMOS values to reset the board to default values. (Default: Disabled)
BCLK/DMI/PEG Frequency(0.1MHz)
Allows you to manually set the CPU base clock and DMI/PCIe bus frequency. The adjustable range is from 800 MHz to 2000 MHz. This item is configurable only when the BCLK/DMI/PEG Clock Control option is enabled.
Important: It is highly recommended that the CPU frequency be set in accordance with the CPU specifications.
System Memory Multiplier (SPD)
Allows you to set the system memory multiplier. Auto sets memory multiplier according to memory SPD data. (Default: Auto)
Memory Frequency(Mhz)
The first memory frequency value is the normal operating frequency of the memory being used; the second is the memory frequency that is automatically adjusted according to the BCLK/DMI/PEG
Frequency(0.1MHz) and System Memory Multiplier settings.
Internal Graphics Clock
Allows you to set the onboard graphics clock. The adjustable range is from 400 MHz to 3000 MHz. (Default:
Auto)
(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website.
- 26 -
Advanced Memory Settings
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Advanced Memory Settings
System Memory Multiplier
Memory Frequency (Mhz)
Performance Enhance
DRAM Timing Selectable
Profile DDR Voltage
Profile VTT Voltage x Channel Interleaving x Rank Interleaving
>>>>> Channel A
Channel A Timing Settings
>>>>> Channel B
Channel B Timing Settings
(SPD)
1333
(SPD)
[Auto]
1333
[Turbo]
[Auto]
1.5V
1.05V
Auto
Auto
[Press Enter]
[Press Enter]
Item Help
Menu Level
: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
System Memory Multiplier (SPD), Memory Frequency(Mhz)
The settings under the two items above are synchronous to those under the same items on the
Advanced Frequency Settings menu.
Performance Enhance
Allows the system to operate at three different performance levels.
Standard Lets the system operate at its basic performance level.
Turbo Lets the system operate at its good performance level. (Default)
Extreme Lets the system operate at its best performance level.
DRAM Timing Selectable (SPD)
Quick and Expert allows the Channel Interleaving, Rank Interleaving, Channel A Timing Settings, and Channel B Timing Settings items to be configurable. Options are: Auto (default), Quick, Expert.
Profile DDR Voltage
Displays the memory voltage as 1.5V.
Profile VTT Voltage
The value displayed here is dependent on the CPU being used.
Channel Interleaving
Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. Auto lets the BIOS automatically configure this setting. (Default: Auto)
Rank Interleaving
Enables or disables memory rank interleaving. Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability. Auto lets the BIOS automatically configure this setting. (Default: Auto)
- 27 -
>>>>> Channel A/B Timing Settings
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Channel A Timing Settings
>>>>> Channel A Standard Timing Control x CAS Latency Time x tRCD x tRP x tRAS
9
9
9
24
>>>>> Channel A Advanced Timing Control x tRC x tRRD x tWTR x tWR x tWTP x tWL x tRFC x tRTP x tFAW
: Move x Command Rate (CMD) x Round Trip Latency
>>>>> Channel A Misc Timing Control x IO Latency
Enter: Select
F5: Previous Values
33
4
5
10
21
7
74
5
20
1
1
34
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
Item Help
Menu Level
ESC: Exit F1: General Help
F7: Optimized Defaults
>>>>> Channel A/B Standard Timing Control
CAS Latency Time
Options are: Auto (default), 5~15.
tRCD
Options are: Auto (default), 1~15.
tRP
Options are: Auto (default), 1~15.
tRAS
Options are: Auto (default), 1~40.
>>>>> Channel A/B Advanced Timing Control
tRC
Options are: Auto (default), 1~63.
tRRD
Options are: Auto (default), 1~15.
tWTR
Options are: Auto (default), 1~15.
tWR
Options are: Auto (default), 1~16.
tWTP
Options are: Auto (default), 1~31.
tWL
Options are: Auto (default), 1~12
tRFC
Options are: Auto (default), 1~255.
tRTP
Options are: Auto (default), 1~15.
tFAW
Options are: Auto (default), 1~63.
- 28 -
Command Rate(CMD)
Options are: Auto (default), 1~3.
>>>>> Channel A/B Misc Timing Control
IO Latency
Options are: Auto (default), 1~31.
Round Trip Latency
Options are: Auto (default), 1~255.
Advanced Voltage Settings
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Advanced Voltage Settings
****** Mother Board Voltage Control ******
Voltage Types Normal Current
-----------------------------------------------------------------------------
>>> CPU
Dynamic Vcore(DVID)
QPI/Vtt Voltage
Graphics DVID
>>> MCH/ICH
PCH Core
+0.000V
1.050V
+0.000V
1.050V
[Auto]
[Auto]
[Auto]
[Auto]
Item Help
Menu Level
DRAM Voltage 1.500V [Auto]
: Move Enter: Select
F5: Previous Values
>>> CPU
Dynamic Vcore(DVID)
The default is Auto.
QPI/Vtt Voltage
The default is Auto.
Graphics DVID
The default is Auto.
>>> MCH/ICH
PCH Core
The default is Auto.
DRAM Voltage
The default is Auto.
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
- 29 -
Miscellaneous Settings
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Miscellaneous Settings
Isochronous Support
Virtualization Technology (Note)
[Enabled]
[Enabled]
Item Help
Menu Level
: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
Isochronous Support
Determines whether to enable specific streams within the CPU and Chipset. (Default: Enabled)
Virtualization Technology (Note)
Enables or disables Intel Virtualization Technology. Virtualization enhanced by Intel Virtualization Technology will allow a platform to run multiple operating systems and applications in independent partitions.
With virtualization, one computer system can function as multiple virtual systems. (Default: Enabled)
(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website.
2-4 Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Fri, Aug 19 2011
22:31:24
Item Help
Menu Level
IDE Channel 0 Master
IDE Channel 1 Master
IDE Channel 2 Master
IDE Channel 3 Master
Halt On
Base Memory
Extended Memory
Total Memory
[None]
[None]
[None]
[None]
[All, But Keyboard]
640K
941M
950M
: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
Date (mm:dd:yy)
Sets the system date.
Time (hh:mm:ss)
Sets the system time.
IDE Channel 0, 1 Master
IDE Channel 0, 1 Master
Configure your SATA devices by using one of the three methods below:
•
•
• None If no SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup.
Auto Lets the BIOS automatically detect SATA devices during the POST. (Default)
Manual Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS.
Access Mode Sets the hard drive access mode. Options are: Auto (default), CHS, LBA, Large.
- 30 -
IDE Channel 2, 3 Master
Extended IDE Drive
Configure your SATA devices by using one of the two methods below:
•
•
Auto Lets the BIOS automatically detect SATA devices during the POST. (Default)
None If no SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup.
Access Mode Sets the hard drive access mode. Options are: Auto (default), Large.
The following fields display your hard drive specifications. If you wish to enter the parameters manually, refer to the information on the hard drive.
Capacity Approximate capacity of the currently installed hard drive.
Cylinder Number of cylinders.
Head Number of heads.
Precomp Write precompensation cylinder.
Landing Zone Landing zone.
Sector Number of sectors.
Halt On
Allows you to determine whether the system will stop for an error during the POST.
Options are: "All Errors," "No Errors," "All, But Keyboard". (Default)
Memory
These fields are read-only and are determined by the BIOS POST.
2-5 Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Advanced BIOS Features
Hard Disk Boot Priority
Quick Boot
EFI CD/DVD Boot Option
First Boot Device
Second Boot Device
Third Boot Device
Password Check
HDD S.M.A.R.T. Capability
Limit CPUID Max. to 3 (Note)
No-Execute Memory Protect (Note)
Delay For HDD (Secs)
Full Screen LOGO Show
Init Display First
Onboard VGA
On-Chip Frame Buffer Size
: Move Enter: Select
F5: Previous Values
[Press Enter]
[Disabled]
[Auto]
[Hard Disk]
[CDROM]
[USB-FDD]
[Setup]
[Disabled]
[Disabled]
[Enabled]
[0]
[Enabled]
[PCIE x16]
[Enable If No Ext PEG]
[64MB+2MB for GTT]
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
Item Help
Menu Level
ESC: Exit F1: General Help
F7: Optimized Defaults
Hard Disk Boot Priority
Specifies the sequence of loading the operating system from the installed hard drives. Use the up or down arrow key to select a hard drive, then press the plus key <+> (or <PageUp>) or the minus key <-> (or
<PageDown>) to move it up or down on the list. Press <Esc> to exit this menu when finished.
Quick Boot
Enables or disables the quick boot function to speed up the system boot-up process to shorten the waiting time for entering the operating system and to deliver greater efficiency for daily use. The settings here synchronize with the settings of the SMART QuickBoot of Smart 6 ™ . (Default: Disabled)
(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website.
- 31 -
EFI CD/DVD Boot Option
Set this item to EFI if you want to install the operating system to a hard drive larger than 2.2 TB. Make sure the operating system to be installed supports booting from a GPT partition, such as Windows 7 64bit and Windows Server 2003 64-bit. Auto lets the BIOS automatically configure this setting depending on the hard drive you install. (Default: Auto)
First/Second/Third Boot Device
Specifies the boot order from the available devices. Use the up or down arrow key to select a device and press <Enter> to accept. Options are: Hard Disk, CDROM, USB-FDD, USB-ZIP, USB-CDROM, USB-
HDD, Legacy LAN, Disabled.
Password Check
Specifies whether a password is required every time the system boots, or only when you enter BIOS
Setup. After configuring this item, set the password(s) under the Set Supervisor/User Password item in the BIOS Main Menu.
Setup A password is only required for entering the BIOS Setup program. (Default)
System A password is required for booting the system and for entering the BIOS Setup program.
HDD S.M.A.R.T. Capability
Enables or disables the S.M.A.R.T. (Self Monitoring and Reporting Technology) capability of your hard drive. This feature allows your system to report read/write errors of the hard drive and to issue warnings when a third party hardware monitor utility is installed. (Default: Disabled)
Limit CPUID Max. to 3 (Note)
Allows you to determine whether to limit CPUID maximum value. Set this item to Disabled for Windows
XP operating system; set this item to Enabled for legacy operating system such as Windows NT4.0.
(Default: Disabled)
No-Execute Memory Protect (Note)
Enables or disables Intel Execute Disable Bit function. This function may enhance protection for the computer, reducing exposure to viruses and malicious buffer overflow attacks when working with its supporting software and system. (Default: Enabled)
Delay For HDD (Secs)
Allows you to set a delay time for the BIOS to initialize the hard drive as the system boots up. The adjustable range is from 0 to 15 seconds. (Default: 0)
Full Screen LOGO Show
Allows you to determine whether to display the GIGABYTE Logo at system startup. Disabled displays normal POST message. (Default: Enabled)
Init Display First
Specifies the first initiation of the monitor display from the installed PCI graphics card, PCI Express graphics card, or the onboard graphics.
PCI Sets the PCI graphics card as the first display.
Onboard Sets the onboard graphics as the first display.
PCIE x16 Sets the PCI Express graphics card on the PCIEX16 slot as the first display. (Default)
Onboard VGA
Enables or disables the onboard graphics function.
Enable If No Ext PEG
Activates the onboard graphics only when no PCI Express graphics card is installed. (Default)
Always Enable
Always activates the onboard graphics, whether or not a PCI Express graphics card is installed. If you wish to set up a dual-display configuration, set this item to Always Enable.
(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website.
- 32 -
On-Chip Frame Buffer Size
Frame buffer size is the total amount of system memory allocated solely for the onboard graphics controller. MS-DOS, for example, will use only this memory for display. Options are: 32MB+2MB for GTT ~
480MB+2MB for GTT. (Default: 64MB+2MB for GTT)
2-6 Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Integrated Peripherals
SATA AHCI Mode
SATA Port0-1 Native Mode
USB Controllers
USB Legacy Function
USB Storage Function
Azalia Codec
Onboard H/W LAN
SMART LAN
Onboard LAN Boot ROM
Onboard USB3.0 Controller k
Onboard Serial Port 1
Onboard Parallel Port
Parallel Port Mode
: Move Enter: Select
F5: Previous Values
[IDE]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Auto]
[Enabled]
[Press Enter]
[Disabled]
[Enabled]
[2F8/IRQ3]
[378/IRQ7]
[SPP]
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
Item Help
Menu Level
ESC: Exit F1: General Help
F7: Optimized Defaults
SATA AHCI Mode (Intel H61 Chipset)
Allows you to decide whether to configure the SATA controller integrated in the Intel H61 Chipset to AHCI mode.
IDE Configures the SATA controller to IDE mode. (Default)
AHCI Configures the SATA controller to AHCI mode. Advanced Host Controller Interface
(AHCI) is an interface specification that allows the storage driver to enable advanced
Serial ATA features such as Native Command Queuing and hot plug.
SATA Port0-1 Native Mode (Intel H61 Chipset)
Specifies the operating mode of the integrated SATA controllers.
Disabled Allows the SATA controllers to operate in Legacy IDE mode.
In Legacy mode the SATA controllers use dedicated IRQs that cannot be shared with other device. Set this option to Disabled if you wish to install operating systems that do not support Native mode.
Enabled Allows the SATA controllers to operate in Native IDE mode. Enable Native IDE mode if you wish to install operating systems that support Native mode. (Default)
USB Controllers
Enables or disables the integrated USB controller. (Default: Enabled)
Disabled will turn off all of the USB functionalities below.
USB Legacy Function
Allows USB keyboard to be used in MS-DOS. (Default: Enabled)
USB Storage Function
Determines whether to detect USB storage devices, including USB flash drives and USB hard drives during the POST. (Default: Enabled)
Azalia Codec
Enables or disables the onboard audio function. (Default: Auto)
If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to
Disabled.
k Only for GA-H61M-D2H-USB3.
- 33 -
Onboard H/W LAN
Enables or disables the onboard LAN function. (Default: Enabled) If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to Disabled.
SMART LAN (LAN Cable Diagnostic Function)
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
SMART LAN
Start detecting at Port.....
Part1-2 Status = Open / Length = 0m
Part3-6 Status = Open / Length = 0m
Part4-5 Status = Open / Length = 0m
Part7-8 Status = Open / Length = 0m
Item Help
Menu Level
: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN cable. This feature will detect cabling issue and report the approximate distance to the fault or short.
Onboard LAN Boot ROM
Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip.
(Default: Disabled)
Onboard USB3.0 Controller (Etron EJ168 USB Controller) k
Enables or disables the Etron EJ168 USB controller. (Default: Enabled)
Onboard Serial Port 1
Enables or disables the first serial port and specifies its base I/O address and corresponding interrupt.
Options are: Auto, 3F8/IRQ4, 2F8/IRQ3 (default), 3E8/IRQ4, 2E8/IRQ3, Disabled.
Onboard Parallel Port
Enables or disables the onboard parallel port (LPT) and specifies its base I/O address and corresponding interrupt. Options are: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.
Parallel Port Mode
Selects an operating mode for the onboard parallel (LPT) port. Options are: SPP (Standard Parallel Port)
(default), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port), ECP+EPP.
k Only for GA-H61M-D2H-USB3.
2-7 Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
Power Management Setup
ACPI Suspend Type
Soft-Off by PWR-BTTN
PME Event Wake Up
Power On by Ring
Resume by Alarm x Date (of Month) Alarm x Time (hh:mm:ss) Alarm
HPET Support (Note)
HPET Mode (Note)
Power On By Mouse
Power On By Keyboard x KB Power ON Password
AC Back Function
ErP Support
[S3(STR)]
[Instant-Off]
[Enabled]
[Enabled]
[Disabled]
Everyday
0 : 0 : 0
[Enabled]
[32-bit mode]
[Disabled]
[Disabled]
Enter
[Soft-Off]
[Disabled]
Item Help
Menu Level
: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
(Note) Supported on Windows 7/Vista operating system only.
- 34 -
ACPI Suspend Type
Specifies the ACPI sleep state when the system enters suspend.
S1(POS) Enables the system to enter the ACPI S1 (Power on Suspend) sleep state. In S1 sleep state, the system appears suspended and stays in a low power mode. The system can be resumed at any time.
S3(STR) Enables the system to enter the ACPI S3 (Suspend to RAM) sleep state (default). In
S3 sleep state, the system appears to be off and consumes less power than in the
S1 state. When signaled by a wake-up device or event, the system resumes to its working state exactly where it was left off.
Soft-Off by PWR-BTTN
Configures the way to turn off the computer in MS-DOS mode using the power button.
Instant-Off Press the power button and then the system will be turned off instantly. (Default)
Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power button is pressed for less than 4 seconds, the system will enter suspend mode.
PME Event Wake Up
Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a PCI or PCIe device. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.
(Default: Enabled)
Power On by Ring
Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a modem that supports wake-up function. (Default: Enabled)
Resume by Alarm
Determines whether to power on the system at a desired time. (Default: Disabled)
If enabled, set the date and time as following:
Date (of Month) Alarm: Turn on the system at a specific time on each day or on a specific day in a month.
Time (hh: mm: ss) Alarm: Set the time at which the system will be powered on automatically.
Note: When using this function, avoid inadequate shutdown from the operating system or removal of the
AC power, or the settings may not be effective.
HPET Support (Note)
Enables or disables High Precision Event Timer (HPET) for Windows 7/Vista operating system.
(Default: Enabled)
HPET Mode (Note)
Allows you to select the HPET mode for your Windows 7/Vista operating system. Select 32-bit mode when you install 32-bit Windows 7/Vista; select 64-bit mode when you install 64-bit Windows 7/Vista.
This item is configurable only when the HPET Support is set to Enabled. (Default: 32-bit mode)
Power On By Mouse
Allows the system to be turned on by a PS/2 mouse wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.
Disabled Disables this function. (Default)
Double Click Double click on left button on the PS/2 mouse to turn on the system.
Power On By Keyboard
Allows the system to be turned on by a PS/2 keyboard wake-up event.
Note: you need an ATX power supply providing at least 1A on the +5VSB lead.
Disabled Disables this function. (Default)
Password Set a password with 1~5 characters to turn on the system.
Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system.
(Note) Supported on Windows 7/Vista operating system only.
- 35 -
KB Power ON Password
Set the password when Power On by Keyboard is set to Password. Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept. To turn on the system, enter the password and press <Enter>.
Note: To cancel the password, press <Enter> on this item. When prompted for the password, press
<Enter> again without entering the password to clear the password settings.
AC Back Function
Determines the state of the system after the return of power from an AC power loss.
Soft-Off The system stays off upon the return of the AC power. (Default)
Full-On The system is turned on upon the return of the AC power.
Memory The system returns to its last known awake state upon the return of the AC power.
ErP Support
Determines whether to let the system consume less than 1W power in S5 (shutdown) state. (Default: Disabled)
Note: When this item is set to Enabled, the following four functions will become unavailable:
PME event wake up, power on by mouse, power on by keyboard, and wake on LAN.
2-8 PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
PC Health Status
Reset Case Open Status
Case Opened
Vcore
DDR15V
+12V
Vcc
Vtt
Current System Temperature
Current CPU Temperature
Current CPU FAN Speed
Current SYSTEM FAN Speed
CPU Warning Temperature
CPU FAN Fail Warning
SYSTEM FAN Fail Warning
CPU Smart FAN Control x Slope PWM
[Disabled]
No
1.200V
1.516V
11.779V
3.478V
1.076V
35 o C
36 o C
1973 RPM
0 RPM
[Disabled]
[Disabled]
[Disabled]
[Normal]
1.75 PWM value / o C
Item Help
Menu Level
: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save ESC: Exit F1: General Help
F7: Optimized Defaults
Reset Case Open Status
Keeps or clears the record of previous chassis intrusion status. Enabled clears the record of previous chassis intrusion status and the Case Opened field will show "No" at next boot. (Default: Disabled)
Case Opened
Displays the detection status of the chassis intrusion detection device attached to the motherboard CI header. If the system chassis cover is removed, this field will show "Yes", otherwise it will show "No". To clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to the CMOS, and then restart your system.
Current Voltage(V) Vcore/DDR15V/+12V/Vcc/Vtt
Displays the current system voltages.
Current System/CPU Temperature
Displays current system/CPU temperature.
- 36 -
Current CPU/SYSTEM FAN Speed (RPM)
Displays current CPU/system fan speed.
CPU Warning Temperature
Sets the warning threshold for CPU temperature. When CPU temperature exceeds the threshold,
BIOS will emit warning sound. Options are: Disabled (default), 60
90 o C/194 o F.
o C/140 o F, 70 o C/158 o F, 80 o C/176 o F,
CPU/SYSTEM FAN Fail Warning
Allows the system to emit warning sound if the CPU/system fan is not connected or fails. Check the fan condition or fan connection when this occurs. (Default: Disabled)
CPU Smart FAN Control
Allows you to determine whether to enable the CPU fan speed control function and adjust the fan speed.
Normal Allows the CPU fan to run at different speeds according to the CPU temperature. You can adjust the fan speed with EasyTune based on your system requirements. (Default)
Silent Allows the CPU fan to run at slow speeds.
Manual Allows you to control the CPU fan speed under the Slope PWM item.
Disabled Allows the CPU fan to run at full speeds.
Slope PWM
Allows you to control the CPU fan speed. This item is configurable only when CPU Smart FAN Control is set to Manual. Options are: 0.75 PWM value / o C ~ 2.50 PWM value / o C.
2-9 Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit
F8: Q-Flash
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
: Select Item
Exit Without Saving
F10: Save & Exit Setup
Load Fail-Safe Defaults
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Press <Enter> on this item and then press the <Y> key to load the safest BIOS default settings.
In case system instability occurs, you may try to load Fail-Safe defaults, which are the safest and most stable
BIOS settings for the motherboard.
- 37 -
2-10 Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit
F8: Q-Flash
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
: Select Item
Exit Without Saving
F10: Save & Exit Setup
Load Optimized Defaults
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Press <Enter> on this item and then press the <Y> key to load the optimal BIOS default settings.
The BIOS defaults settings help the system to operate in optimum state. Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values.
2-11 Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit
F8: Q-Flash
: Select Item
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
F10: Save & Exit Setup
Change/Set/Disable Password
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Press <Enter> on this item and type the password with up to 8 characters and then press <Enter>. You will be requested to confirm the password. Type the password again and press <Enter>.
The BIOS Setup program allows you to specify two separate passwords:
Supervisor Password
When a system password is set and the Password Check item in Advanced BIOS Features is set to
Setup, you must enter the supervisor password for entering BIOS Setup and making BIOS changes.
When the Password Check item is set to System, you must enter the supervisor password (or user password) at system startup and when entering BIOS Setup.
User Password
When the Password Check item is set to System, you must enter the supervisor password (or user password) at system startup to continue system boot. In BIOS Setup, you must enter the supervisor password if you wish to make changes to BIOS settings. The user password only allows you to view the
BIOS settings but not to make changes.
To clear the password, press <Enter> on the password item and when requested for the password, press
<Enter> again. The message "PASSWORD DISABLED" will appear, indicating the password has been cancelled.
- 38 -
2-12 Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
ESC: Quit
F8: Q-Flash
: Select Item
F10: Save & Exit Setup
Save Data to CMOS
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Press <Enter> on this item and press the <Y> key. This saves the changes to the CMOS and exits the BIOS
Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu.
2-13 Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit
F8: Q-Flash
Load Fail-Safe Defaults
: Select Item
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
F10: Save & Exit Setup
Abandon all Data
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Press <Enter> on this item and press the <Y> key. This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS. Press <N> or <Esc> to return to the BIOS Setup Main Menu.
- 39 -
Chapter 3 Drivers Installation
•
• Before installing the drivers, first install the operating system.
After installing the operating system, insert the motherboard driver disk into your optical drive.
The driver Autorun screen is automatically displayed which looks like that shown in the screen shot below. (If the driver Autorun screen does not appear automatically, go to My Computer, double-click the optical drive and execute the Run.exe program.)
After inserting the driver disk, "Xpress Install" will automatically scan your system and then list all the drivers that are recommended to install. You can click the Install All button and "Xpress Install" will install all the recommended drivers. Or click Install Single Items to manually select the drivers you wish to install.
- 40 -
Regulatory Statements
Regulatory Notices
This document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects at the time of printing. GIGABYTE cannot, however, assume any responsibility for errors or omissions in this text. Also note that the information in this document is subject to change without notice and should not be construed as a commitment by
GIGABYTE.
Our Commitment to Preserving the Environment
In addition to high-efficiency performance, all GIGABYTE motherboards fulfill European Union regulations for RoHS (Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment) and WEEE
(Waste Electrical and Electronic Equipment) environmental directives, as well as most major worldwide safety requirements. To prevent releases of harmful substances into the environment and to maximize the use of our natural resources, GIGABYTE provides the following information on how you can responsibly recycle or reuse most of the materials in your "end of life" product.
Restriction of Hazardous Substances (RoHS) Directive Statement
GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6,
PBDE and PBB). The parts and components have been carefully selected to meet RoHS requirement.
Moreover, we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals.
Waste Electrical & Electronic Equipment (WEEE) Directive Statement
GIGABYTE will fulfill the national laws as interpreted from the 2002/96/EC WEEE (Waste Electrical and
Electronic Equipment) directive. The WEEE Directive specifies the treatment, collection, recycling and disposal of electric and electronic devices and their components. Under the Directive, used equipment must be marked, collected separately, and disposed of properly.
WEEE Symbol Statement conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local government office, your household waste disposal service or where you purchased the product for details of environmentally safe recycling.
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure.
The separate collection and recycling of your waste equipment at the time of disposal will help to
When your electrical or electronic equipment is no longer useful to you, "take it back" to your local or regional waste collection administration for recycling.
If you need further assistance in recycling, reusing in your "end of life" product, you may contact us at the
Customer Care number listed in your product's user's manual and we will be glad to help you with your effort.
Finally, we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly.
With your help, we can reduce the amount of natural resources needed to produce electrical and electronic equipment, minimize the use of landfills for the disposal of "end of life" products, and generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly.
- 41 -
- 42 -
- 43 -
Contact Us
GIGA-BYTE TECHNOLOGY CO., LTD.
Address: No.6, Bao Chiang Road, Hsin-Tien Dist., New Taipei City 231,Taiwan
TEL: +886-2-8912-4000, FAX: +886-2-8912-4003
Tech. and Non-Tech. Support (Sales/Marketing) : http://ggts.gigabyte.com.tw
WEB address (English): http://www.gigabyte.com
WEB address (Chinese): http://www.gigabyte.tw
You may go to the GIGABYTE website, select your language in the language list on the top right corner of the website.
• GIGABYTE Global Service System
To submit a technical or non-technical (Sales/Marketing) question, please link to: http://ggts.gigabyte.com.tw
Then select your language to enter the system.
- 44 -
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Intel LGA 1155 (Socket H2) Intel® Celeron®, Intel® Pentium®
PC micro ATX Intel® H61 Realtek ALC889 7.1 channels
DDR3-SDRAM 4 DIMM Non-ECC Maximum internal memory: 16 GB
SATA II
BIOS type: AWARD 64 Mbit ACPI version: 1.0b Clear CMOS button
Gigabit Ethernet
Frequently asked questions
The GA-H61M-D2H-USB3 supports dual-channel DDR3 memory.
The GA-H61M-D2H-USB3 has two PCI Express x16 slots.
Yes, the GA-H61M-D2H-USB3 has an integrated graphics controller.