StarTech.com ST121DVI25 Instruction manual

Instruction Manual

DVI Video Extender over Cat 6 UTP

High Speed HDMI® over Cat 6 UTP

ST121DVI25

ST121HD25

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

ST121DVI25

Packaging Contents

• 1 x Video Extender Transmitter

• 1 x Video Extender Receiver

• 2 x Universal Power Adapter

• 1 x Instruction Manual

System Requirements

• DVI-D/HDMI enabled video source device (e.g. computer)

• DVI-D/HDMI enabled display device (e.g. monitor, projector)

• Available AC electrical outlet for transmitter and receiver

• DVI-D/HDMI cable from receiver to display

• DVI-D/HDMI cable from video source to transmitter

• Cat6 UTP Ethernet cable (see “Preparing Your Site”)

Preparing Your Site

1. Determine where the local video source (i.e. computer) will be located and set up the device.

2. Determine where the remote display will be located and place/ mount the display appropriately.

Please note that both extender units will require a power connection, so please ensure that each unit will be situated near an available AC electrical outlet.

3. If you are using surface cabling, ensure you have enough Cat6 unshielded twisted pair (UTP) Ethernet cabling to connect the

Local Unit to the Remote Unit’s location, and that each end is terminated with a RJ45 Ethernet connector. The cabling should not go through any networking equipment (i.e. router, switch).

OR

If you are using premise cabling, ensure that the Cat6 unshielded twisted pair (UTP) Ethernet Cabling between the Local Unit and the Remote Unit has been properly terminated in a wall outlet/ panel in each location and there is a patch cable long enough to connect the Remote Unit and the Local Unit to their respective outlets. The cabling should not go through any networking equipment (i.e. router, switch).

For the most up-to-date information, please visit: www.startech.com

*actual product may vary from photos

Installation

1. Turn off the video source (i.e. computer) and the intended display device (i.e. monitor).

2. Position the Receiver Unit near the remote display.

3. Position the Transmitter Unit near the video source.

4. Connect the video source to the DVI/HDMI port on the rear panel of the Transmitter Unit, using a male/male cable.

5. Connect the remote display to the DVI/HDMI port located on the rear panel of the Receiver Unit using a male/male cable.

6. Connect the Transmitter Unit to the Receiver Unit, using standard

RJ45 terminated UTP Cat6 cable (see “Preparing Your Site”).

7. Connect the power adapters (provided) to both Transmitter and

Receiver Units.

NOTE: Both units can also be powered from a local USB port, by using a USB cable (sold separately). You may also only connect power to the Transmitter Unit, however maximum UTP cable length will be reduced to 20m.

8. Turn on the display device first, followed by the video source.

Wiring Diagram

The UTP cable must be wired according to the EIA/TIA 568B industry standard as shown below.

5

6

3

4

7

8

Pin

1

2

Wire Color

White/Orange

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

Pair

2

3

4

3

1

Manual Revision: 09/01/2011

ST121HD25

*actual product may vary from photos

Specifications

Video Signal

Connectors

(Transmitter Unit)

Connectors

(Receiver Unit)

LEDs

Maximum Video Resolution

Maximum Cable Length

Power Adapter

Enclosure Material

Operating Temperature

Storage Temperature

Humidity

Dimensions (per Unit)

Weight (per Unit)

ST121DVI25

DVI-D (digital)

ST121HD2

HDMI

1 x DVI-I 29-pin female

1 x RJ45 Ethernet female

1 x USB mini-B female (power)

1 x DVI-I 29-pin female

1 x RJ45 Ethernet female

1 x USB mini-B female (power)

1 x HDMI type A female

1 x RJ45 Ethernet female

1 x USB mini-B female (power)

1 x HDMI type A female

1 x RJ45 Ethernet female

1 x USB mini-B female (power)

Transmitter: 1 x Power

Receiver: 1 x Power

1920 x 1080 (1080p) @ 25m

Cat6: 25m / 80ft

DVI: 10m / 32ft

Cat6: 25m / 80ft

HDMI: 10m / 32ft

5VDC, 1000mA

Plastic

0°C ~ 40°C (32°F ~ 104°F)

0°C ~ 60°C (32°F ~ 140°F)

20% ~ 90% RH

80.0mm x 55.0mm x 23.0mm

75.0mm x 55.0mm x 23.0mm

110g 110g

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.