Samsung SCD-2040 User guide
Add to my manuals19 Pages
Samsung SCD-2040 is a high-resolution day and night dome camera that delivers clear images with 600 TV lines of resolution in color mode. It features a 1/3" 410,000 (NTSC) pixels, 470,000 (PAL) pixels SONY CCD, HLC (High Light Compensation), SENS-UP, FLIP (H/V-REV), D-ZOOM, SHARPNESS, and PRIVACY functions. The camera also has a built-in high sensitivity COLOR CCD that produces clear images even in low-light conditions, a 3-axis camera mechanism for flexible installation, and supports coaxial communication methods.
advertisement
▼
Scroll to page 2
of 19
High Resolution Day & Night Dome Camera SCD-2020/2040/2021 User Guide Before installing and operating this product, please read this manual thoroughly. ENGLISH Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we'll introduce our model description. nSCD-2020/2040/2021 SERIES • NTSC MODEL SCD-2020N/2040N/2021N • PAL MODEL SCD-2020P/2040P/2021P n MODEL DESCRIPTION • SCD-2020X/2040X/2021X 0_ The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. SIGNAL SYSTEM • SIGNAL SYSTEM N → NTSC MODEL P → PAL MODEL The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING - C hanges or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. WARNING - To prevent electric shock and risk of fire hazards: ◆ Do NOT use power sources other than that specified. ◆ Do NOT expose this appliance to rain or moisture. This installation should be made by a qualified service person and should conform to all local codes. Contents Contents Features • Features…………………………………………………………………………… 5 • Warnings & Cautions… ……………………………………………………… 6 • Precautions… …………………………………………………………………… 7 Miscellaneous Functions High Resolution By adopting a diagonal 6mm(1/3") 410,000 (NTSC) pixels, 470,000(PAL) pixels SONY CCD, the camera produces clear picture quality with a horizontal resolution of 600 TV lines in color mode. HLC(High Light Compensation), SENS-UP, FLIP (H/ V-REV), D-ZOOM, SHARPNESS and PRIVACY functions are provided. • Components and Accessories……………………………………………… 8 • Overview…………………………………………………………………………… 9 • Installation………………………………………………………………………… 10 ■ Installation…………………………………………………………………………………… ■ Adjust the panning and tilting, rotating while watching the monitor… ……………… • Connection………………………………………………………………………… ■ Connecting To Monitor…………………………………………………………………… ■ Connecting To Power……………………………………………………………………… ■ Using Coaxial Communications… ………………………………………………………… 10… 12 13 13… 13 14 • Operating Your Camera……………………………………………………… 15 ■ Menu Configration………………………………………………………………………… 15… enu Setup………………………………………………………………………………… 16 ■M • Lens Shade…………………………………………………………………………… • Exposure……………………………………………………………………………… • White Balance… …………………………………………………………………… • SSDR (Samsung Super Dynamic Range)… ……………………………………… • Backlight……………………………………………………………………………… • SSNR3………………………………………………………………………………… • Day / Night…………………………………………………………………………… • Special… …………………………………………………………………………… • Exit…………………………………………………………………………………… 17… 17… 19… 20… 21 23… 24… 25… 30 Lens Shading Compensation Excellent Sensitivity The built-in high sensitivity COLOR CCD produces a clear image even in 0.15Lux(COLOR), 0.0003Lux (Color, SENS-UP x512) or lower illumination. SSNR3 Function (Samsung Super Noise Reduction) The high-performance W-V DSP chip effectively removes low-light gain noise and afterimage to provide clear images even in dark environments. LENS SHADE diminishes brightness contrast to obtain balanced view in the monitor. OSD The camera’s OSD is complimented by 18 languages. - NTSC : Korean, English, French, Spanish, Japanese, Portuguese, Taiwanese - PAL : English, Chinese, German, Italian, French, Spanish, Russian, Czech, Polish, Romanian, Serbian, Swedish, Danish, Turkish, Portuguese Day & Night (Electronic Type) This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions. The COLOR mode operates in daytime conditions to provide optimum colors, and B/W mode operates in nighttime conditions to enhance the definition of the image. DIS (Digital Image Stabilizer) The DIS function compensates for any camera movement, to produce more stable pictures. Motion Detection Since the camera detects motion without any additional external sensor, you can monitor activity more efficient. SSDR (Samsung Super Dynamic Range) For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting, this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness. • Troubleshooting………………………………………………………………… 31 • Specifications………………………………………………………………… 32 • Dimension… …………………………………………………………………… 33 COLOR DOME CAMERA 4 User Guide 3-Axis camera mechanism The SCD-2020/2040/2021 is especially incredibly flexible to install with its 3-axis camera construction, which makes the camera wall or slope mountable. Communication Coaxial communication methods are supported. - Protocol : Pelco Coaxitron COLOR DOME CAMERA 5 User Guide Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products.The Eco mark represents Samsung Techwin’s will to create environment-friendly products, and indicates that the product satisfies the EU RoHS Directive. Precautions Do not install under extreme temperature conditions. Do not install in high humidity environment. Warnings & Cautions This information is provided to ensure your safety and to prevent any losses, financial or otherwise. Please read it carefully and use the product accordingly. * For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as an aerial ladder while providing after-sales service shall be at your expense. * Separate the power plug during a thunder storm. * This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or personal injuries by robbery, fire, natural disaster or other such events. Warning/Attention/Special Mark Messages Ignoring this information may result in material loss and/or serious personal injuries including death. Ignoring this information may result in material loss and/or a slight injuries. Indicates “Never Allowed.” Indicates “No Disassembling.” Use only under temperature conditions between -10ºC and +50ºC. Provide good ventilation when using in high temperature conditions. May lower image quality. Do not install under unstable lighting conditions. Severe lighting changes or flickering may hinder normal camera operation. Avoid touching the camera lens. The lens is the most important component of the camera. Be careful not to smear it with fingerprints. Do not drop the camera or subject it to physical shock. May cause a product malfunction. COLOR DOME CAMERA 6 User Guide Never keep the camera face to strong light directly. May damage the CCD. COLOR DOME CAMERA 7 User Guide Overview Precautions Do not expose the camera to radioactivity. Do not expose the camera to rain or other types of liquids. 9 ❶ 2 4 8 If exposed to radioactivity, the CCD will fail. May cause a product malfunction.Wipe dry any liquids. Liquids may contain minerals that are corrosive to electronic components. Notes 3 • Exposure to a spotlight or an object emitting strong light may cause smear or blooming. • Ensure that the power source complies with normal specifications before supplying it to the camera. 5 7 6 ❶ Pan Base : Control panning angle of camera Components and Accessories 4 3 ❶ 2 ❶ SCD-2020/2040/2021 2 Instruction Manual 3 M4 Tapping Screw 3EA 4 8mm Lens (for SCD-2021 N/P) COLOR DOME CAMERA 8 User Guide 2R otate Base : Control rotating angle of camera 3 Tilt Base : Control tilting angle of camera 4L ens Module : SCD-2020N/P - f=3.7mm, F2.0 SCD-2040N/P - f=8.0mm, F2.0 SCD-2021N/P - f=3.7mm, F2.0 (Additional Lens : f=8.0mm, F2.0) 5 Power Input Connector 6 Video Output Jack 7 Function Setup Switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item. 8 Dome Cover 9 Shield Case COLOR DOME CAMERA 9 User Guide Installation Installation Installation When using the Ceiling bracket 1) Separate the dome cover by turning anti-clockwise. 2) Separate the shield case by pulling from the camera body. Ceiling bracket Main Body (Camera) M4 tapping screw (provided) Latch Unlocking direction (Anti-clockwise) Locking Direction (Clockwise) Unlocking direction * To install the dome cover on the camera body, turn the latches in locking direction as shown in the figure-1. 1) Hold the ceiling bracket (located where the arrow points to) and separate it from the main body of the camera by rotating it anti-clockwise. (refer to the picture in 'Notes' on page 10) 2) Place the separated ceiling bracket so that the “Front” side faces the area to be monitored and install it with the M4 tapping screws. 3) To combine the main body with the ceiling bracket, make sure that the pan base fixation screw face the opposite side of the “Front” side of the ceiling bracket and rotate it clockwise. 4) Adjust the camera lens to face the area to be monitored and fix the main body and the dome cover by aligning the grooves and rotating the body clockwise. Pan Base fixation screw Locking direction Dome Cover [Figure-1] An arrow for installing directions Dome Cover M4 tapping screw [Figure-2] Notes Notes • The installation should be done by qualified service personnel or system installers. • If the ceiling material is not strong enough to hold the installation screws, the camera may fall off. Reinforce the ceiling as needed. • To change the position of the cable, take away the Hole Cover and pass the cable through. COLOR DOME CAMERA 10 User Guide Original position of the cable Hole Cover • If you want to install the camera with the ceiling bracket combined, fix it using two M4 tapping screws at the side of the main body (refer to the [Figure-2] on page 11). When changing the additional lens. 1) Separate the built-in lens by anti-clockwise rotation and combine wave washer and another lens. When combining the lens, please clean the back side of lens and inside of the lens holder. 2) Combining the lens by clockwise rotation, adjust the focus while watching the monitor. COLOR DOME CAMERA 11 User Guide Connection Installation 3) Please change the EFL in LENS SAHDE menu after changing the lens, so that the function operates properly. Connecting to Monitor Connect the Video Output jack to the VIDEO-IN jack of monitor. Adjust the panning and tilting, rotating while watching the monitor Monitor 75˚ 174˚ 174˚ CCTV Camera 176˚ Tilt Base Rotate Base Pan Base • As the connecting method varies with the instruments, refer to the manual supplied with the instrument. • Only connect the cable when the power is turned off. Connecting to Power Connect the adaptor to the power input connector as shown in the figure below. The recommended adaptor specification for SCD-2020N/P, SCD-2040N/P, SCD-2021N/P is AC 24V / 300mA or DC 12V / 500mA. 176˚ ---- Power Input Terminal 1) You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism. • Pan Base moves by 176° to each side direction and 352° on the whole. • Tilt Base covers 75˚ angle. • Rotate Base moves by 174° to each side direction and 348° on the whole. 2) Methods of adjustment • The case of wall installation 1A fter mounting the camera on a wall, adjusting the panning angle so that the camera can face the direction to monitor when tilted. 2 Adjust the tilting angle by rotating the tilt base. 3 Loosen the rotate base hold screw and adjust rotate base for the best view. 4 Tighten the rotate base hold screw. • The case of ceiling installation 1A fter mounting the camera on a ceiling, adjusting the panning angle to the correct viewing position by rotating the pan base. 2 Adjust the tilting angle by rotating the tilt base. 3 Loosen the rotate base hold screw and adjust rotate base for the best view. 4 Tighten the rotate base hold screw. COLOR DOME CAMERA 12 User Guide When the resistance value of copper wire is at [20°C(68°F)] Copper wire size (AWG) #24(0.22mm2) #22(0.33mm2) #20(0.52mm2) #18(0.83mm2) Resistance (Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 • As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera. *Standard voltage for camera operation : AC 24V ±10% / DC 12V ±10% *There may be some deviation in voltage drop depending on the type of wire and the manufacturer. COLOR DOME CAMERA 13 User Guide Operating Your Camera Connection Menu Configration Notes • Be sure to connect power only after all the installation is complete. • Note that AC / DC adaptor is not supplied with camera. • Ground should be connected to the GND terminal. MAIN SETUP Using Coaxial Communications CAMERA SET UP DOWN LEFT RIGHT • Coaxial Communications System • OSD Control method DVR MENU/ENTER UP KEY DOWN KEY LEFT KEY RIGHT KEY CONTROLLER OSD KEY JOYSTICK UP JOYSTICK DOWN JOYSTICK LEFT JOYSTICK RIGHT DVR DVD • : BNC • ----: RS-485 • Video Cable The camera's video output port is connected to the monitor with a BNC coaxial cable, shown below : If the distance between the camera and the monitor exceeds the recommended maximum, please use an auxiliary video amp. Distance 300m 450m 600m LENS SHADE ●ON ●OFF EXPOSURE ●BRIGHTNESS ●SENS-UP ●SHUTTER ●AGC ●RETURN ●ATW ●OUTDOOR ●MANUAL ●AWC→SET SSDR ●ON ●OFF BACKLIGHT ●BLC ●HLC SSNR3 ●ON ●OFF DAY/NIGHT ●COLOR ●B/W SPECIAL ●IMAGE ADJ ●SYNC ●DIS ●MONITOR ●CAM TITLE ●MOTION DET ●PRIVACY ●LANGUAGE ●RETURN EXIT ●SAVE ●NOT SAVE WHITE BAL Recommended Cable Specification 3C2V(RG-59/U) 5C2V(RG-6/U) 7C2V(RG-11/U) Notes • It is recommended that pure copper coax cable is used and not copper coated steel, as this will cause issues with the communication over the coaxial cable. COLOR DOME CAMERA 14 User Guide COLOR DOME CAMERA 15 User Guide ●INDOOR ●OFF ●AUTO ●RESET Operating Your Camera Menu Setup LENS SHADE Use the Function Setup switch within the camera. LENS SHADE diminishes brightness contrast to obtain balanced view in the monitor. MAIN SETUP 1.LENS SHADE 2.EXPOSURE Function Setup switch 1. Press the Function Setup switch. • Main setup menu is displayed on the monitor screen. Select the function by moving up or down direction of function setup switch. MAIN SETUP 1.LENS SHADE ON 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF 6.SSNR3 ON 7.DAY/NIGHT COLOR 8.SPECIAL 9.EXIT SAVE Change the status by moving right or left direction of function setup switch. 2. Select a desired function using the Function Setup switch. • Place the cursor over a desired item. 3. Set up a selected item by using the Function Setup switch. 4. To finish the setting, select ‘EXIT’ and press the Function Setup switch. Notes • An item with the icon also has sub menus. To select a sub menu, select an item with the icon and press the Function Setup switch. • An item with the - - - icon is unavailable due to function settings. COLOR DOME CAMERA 16 User Guide ON - OFF : LENS SHADE NOT IN USE - ON : LENS SHADE IN USE - EFL : You can choose Effective Focal length of lens. (2.8mm, 3.0mm, 3.7mm, 6.0mm, 8.0mm) - Default setting value of EFL · SCD-2020N/P : 3.7mm · SCD-2040N/P : 8.0mm · SCD-2021N/P : 3.7mm - SHADE GAIN : Please adjust brightness gain on the fringe of monitor. Notes • Change EFL only when you change lenses. • Applicable lenses: F2.0, EFL=2.8mm, 3.0mm, 3.7mm, 6.0mm, 8.0mm. • The bigger SHADE GAIN can make the brighter fringe area but also the more image distortion and noise. EXPOSURE MAIN SETUP 1.LENS SHADE 2.EXPOSURE 3.WHITE BAL ON ATW 1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the Function Setup switch so that the arrow indicates 'EXPOSURE'. 2. Select a desired mode using the Function Setup switch. COLOR DOME CAMERA 17 User Guide Operating Your Camera EXPOSURE SETUP 1.BRIGHTNESS 25 2.SHUTTER --3.AGC HIGH 4.SENS-UP OFF 5.RETURN BRIGHTNESS : Adjusts the video brightness. SHUTTER : You can select the shutter. - ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject. - MANUAL : You can control shutter speed manually. NTSC : x512 ~ x2, 1/60 ~ 1/120,000 sec PAL : x512 ~ x2, 1/50 ~ 1/120,000 sec - A.FLK : Select this when you experience picture flicker, this happens when there is a clash with the installed lighting frequency. Notes • Set the shutter mode to --- if color rolling occurs. • When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the picture may become unstable if the camera faces a bright fluorescent light. Therefore, take care when choosing the installation position. • When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled. AGC (AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but the greater the noise. - OFF : Deactivates the AGC function. - LOW : Allows automatic gain control from 5.3dB to 32dB. - HIGH : Allows automatic gain control from 5.3dB to 37dB. SENS-UP : When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated. - OFF : Deactivates the SENS-UP function. - AUTO : Activates the SENS-UP function. COLOR DOME CAMERA 18 User Guide Notes • If you set the Function Setup switch to ‘AUTO’ mode, you can adjust the brightness by increasing or decreasing the shutter speed. (x2 ~ x512) • Note that the higher the zoom level, the brighter the screen, but the more likely it is that an after-image will appear. • Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the zoom level is increased, this is normal. RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP menu. White Bal (White Balance) Use the White Balance function to adjust the screen color. 1. When the SETUP menu screen is displayed, select ‘White Bal.’ by using the Function Setup switch so that the arrow indicates ‘White Bal’. 2. Select a desired mode using the Function Setup switch. MAIN SETUP 1.LENS SHADE 2.EXPOSURE 3.WHITE BAL 4.SSDR ON ATW OFF ※ Select one of the following 5 modes, as appropriate for your purpose. ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K. OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K. (sodium light inclusion) INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K. COLOR DOME CAMERA 19 User Guide Operating Your Camera MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that switch to MANUAL mode, fine-tune the White Balance and the Function Setup switch. AWC →SET : To find the optimal luminance level for the current environment, point the camera towards a sheet of white paper and press the Function Setup switch. If the environment changes, readjust it. 1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the Function Setup switch so that the arrow indicates ‘SSDR’. 2. Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas. Notes • White Balance may not work properly under the following conditions. In this case select the AWC mode. ❶ When the color temperature of the environment surrounding the subject is out of the control range (e.g. clear sky or sunset). 2 When the ambient illumination of the subject is dim. 3 If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable. SSDR ON SSDR OFF BACKLIGHT This camera is designed so that it delivers a distinctive subject and background at the same time, even when the subject is in backlight, unlike conventional cameras, by adopting a proprietary W-IV DSP chip. 1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function Setup switch so that the arrow indicates BACKLIGHT . SSDR (Samsung Super Dynamic Range) SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas. MAIN SETUP 1.LENS SHADE 2.EXPOSURE 3.WHITE BAL 4.SSDR 5.BACKLIGHT COLOR DOME CAMERA ON ATW OFF OFF 20 User Guide MAIN SETUP 1.LENS SHADE 2.EXPOSURE 3.WHITE BAL 4.SSDR 5.BACKLIGHT 6.SSNR3 ON ATW OFF OFF ON 2. S elect a desired mode using the Function Setup switch depending on the camera purpose. BLC : Enables a user to select a desired area on a picture and view that area more clearly. COLOR DOME CAMERA 21 User Guide Operating Your Camera - LEVEL : Adjust level of the BLC function. - TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced. HLC (High Light Compensation) : If the scene contains extremely bright light areas such as; from car headlight, the light can mask out much of the on-screen detail. - LEVEL : Adjust level of the HLC function. - LIMIT : Enable to change the operating condition. - MASK COLOR/TONE : Change the color / brightness of the masking area. (Black, Red, Blue, Cyan, Magenta) - TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced. SSNR3 This function reduces the background noise in a low luminance environment. 1. When the SETUP menu screen is displayed, select 'SSNR3' by using the Function Setup switch so that the arrow indicates 'SSNR3' . OFF : Not being used 3. S elect a desired mode using the Function Setup switch. Select ‘BLC’ to adjust the area to be HLC : E nable the user to change the level, enhanced then adjust the level. limit, mask color/tone and area. MAIN SETUP 1.LENS SHADE ON 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF 6.SSNR3 ON 7.DAY/NIGHT COLOR 2. Select a desired mode using the Function Setup switch. OFF: Deactivates SSNR3. Noise is not reduced. ON : Activates SSNR3 so that noise is reduced. 3. Set the SSNR3 mode to ‘ON’ and press the Function Setup switch. Then you can adjust the noise reduction level. Notes • Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance. • When dark, the HLC is only activated when a bright light exceeding a specific size. (In NIGHT ONLY mode.) • The HLC is not activated in day light or when bright light is not present at night. (In NIGHT ONLY mode.) • When HLC function is used, D-ZOOM and DIS functions are not activated. COLOR DOME CAMERA 22 User Guide Notes • You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’. • When adjusting the noise reduction level in the SSNR3 mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image. COLOR DOME CAMERA 23 User Guide Operating Your Camera SPECIAL DAY/NIGHT You can display pictures in color or black and white. 1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Function Setup switch so that the arrow indicates ‘DAY/NIGHT’. MAIN SETUP 1.LENS SHADE ON 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF 6.SSNR3 ON 7.DAY/NIGHT COLOR 8.SPECIAL 2. S elect a desired mode using the Function Setup switch according to the picture display you want. COLOR : The picture is always displayed in color. B/W : The picture is always displayed in black and white. You can turn on or off the burst signal on B/W mode. AUTO : The mode is switched to ’Color‘ in a normal environment, but switches to ’B/W‘ mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function Setup switch. You can turn on or off the burst signal on B/W mode. - DURATION : You can select the day/night switching point. - DWELL TIME : You can select the duration time about changing the day/night mode. … →3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s Notes • When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as selecting 'COLOR' mode and 'AUTO' mode cannot be selected. COLOR DOME CAMERA 24 User Guide 1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup switch so that the arrow indicates ‘SPECIAL’. MAIN SETUP 1.LENS SHADE ON 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF 6.SSNR3 ON 7.DAY/NIGHT COLOR 8.SPECIAL 9.EXIT SAVE 2. Select a desired mode using the Function Setup switch. 1. 2. 3. 4. 5. 6. 7. 8. 9. SPECIAL IMAGE ADJ MONITOR LCD CAM TITLE OFF SYNC INT MOTION DET OFF PRIVACY OFF DIS OFF LANGUAGE ENGLISH RETURN IMAGE ADJ : 1) W hen the SPECIAL menu screen is displayed, select ‘IMAGE ADJ’ by using the Function Setup switch so that the arrow indicates ’IMAGE ADJ‘. COLOR DOME CAMERA 25 User Guide Operating Your Camera 2) Select a desired mode using the Function Setup switch. 1. 2. 3. 4. 5. 6. IMAGE SETUP V-REV OFF H-REV OFF D-ZOOM OFF FONT COLOR WHITE SHARPNESS ON RETURN • V-REV : You can flip the picture vertically on the screen. • H-REV : You can flip the picture horizontally on the screen. • D-ZOOM : You can use a digital zoom of x1 ~ x16. • FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue) • SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of the picture. • RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to the SPECIAL menu. CAM TITLE : If you enter a title, the title will appear on the monitor. 1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘CAM TITLE’. 2) Set it to ‘ON’ by using the Function Setup CAMERA TITLE SETUP switch. ABCDEFGHIJKLM NOPQRSTUVWXYZ 3) Press the Function Setup switch. abcdefghijklm 4) Use the Function Setup switch to move nopqrstuvwxyz to a desired letter and select the letter by -.0123456789 pressing the Function Setup switch. ←→CLR POS END Repeat this to enter multiple letters. You can enter up to 15 letters. 5) Enter a title, move the cursor to ‘POS’ and press FRONT DOOR the Function Setup switch. The entered title appears on the screen. Select the position to display the title on the screen by using the Function Setup switch and press the Function Setup switch. When the position is determined, select ‘END’ and press the Function Setup switch to return to the SPECIAL menu. Notes Notes • When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one. • Only English is available in this mode. • If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch. • When the V-REV or H-REV mode is enabled, the text on the screen does not flip. • If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear. Monitor : Please change the settings value of video appropriate to your monitor. - LCD : Please select this menu item when using an LCD monitor. You can change the gamma, PED level and color gain in the sub menus. - CRT : Please select this menu item when using a CRT monitor. - USER: Please use this menu item when using a monitor other than standard ones. You can change the gamma, PED level, and color gain in the sub menus. COLOR DOME CAMERA 26 User Guide SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL), you can synchronize the output phase of multiple cameras using the power synchronization function (Line-Lock) without using a synchronization signal generator. - INT : Internal Synchronization Type - L/L : Power Synchronization Type, Line-lock COLOR DOME CAMERA 27 User Guide Operating Your Camera PRIVACY :Mask an area you want to hide on the screen. • Press the Function Setup switch. • Y ou can select a desired phase from 0 to 359 when select 'phase'. Notes 1. 2. 3. 4. 5. 6. 7. 8. 9. • When using AC power at 60Hz(NTSC), 50Hz(PAL) frequency, you can use the L/L type synchronization. • When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode. MOTION DET : This product has a feature that allows you to observe movement of objects in 8 different areas on the screen, and the words 'MOTION DETECTED' appear on the screen when movement is detected. You can monitor activity more efficient. When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates 'MOTION DET'. Set up the mode using the Function Setup switch. - SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement. - AREA MODE : Determines whether to use the MD area selected in SENSITIVITY. - SEL POS : Determines which of the 4 vertices of each MD area is to be used. - XPOS : Determines the coordinate of the horizontal axis for SEL POS. - YPOS : Determines the coordinate of the vertical axis for SEL POS. - FILL → SET : F ills in a selected MD area. The color of filling is sequentially selected as brown, orange, blue, cyan, green, yellow, magenta and red. - RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu. PRIVACY AREA SETUP AREA AREA1 MODE OFF MASK COLOR GREEN MASK TONE 1 TOP 39 BOTTOM 79 LEFT 13 RIGHT 52 RETURN 1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates ‘PRIVACY’. 2) Set up the mode using the Function Setup switch. - AREA : You can select up to 12 PRIVACY areas. - MODE : Determines whether to use the area selected in the AREA. - MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray. - MASK TONE : Adjust the brightness of MASK COLOR. - TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area. - RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu. DIS (Digital Image Stabilizer) : This function mitigates any picture movement due to external factors such as wind. Resets the camera settings to the factory defaults. Language is not initialized. Notes Notes • MOTION DET areas show only MOTION DET menu. Therefore, MOTION DET areas don’t display on the monitor screen. COLOR DOME CAMERA 28 User Guide • As the DIS function uses the digital zoom, the camera's resolution will decrease. • DIS doesn’t operate when background illumination is too low. • DIS doesn’t operate when object pattern is monotonic as like sky or white wall. COLOR DOME CAMERA 29 User Guide Troubleshooting Operating Your Camera LANGUAGE : You can select the menu language according to your requirements. - NTSC: English, Korean, Japanese, Spanish, French, Portuguese, Taiwanese. - PAL : English, Chinese, German, Italian, French, Spanish, Russian, Czech, Polish, Romanian, Serbian, Swedish, Danish, Turkish, Portuguese. RETURN : S elect this to save the SPECIAL menu settings and return to the MAIN SETUP menu. If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. ● Nothing appears on the screen. ▶ Check that the power cord and line connection between the camera and monitor are properly connected. ▶ Check that you have properly connected VIDEO cable to the camera VIDEO output jack. EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose. - SAVE : Save the current settings and exit the MAIN SETUP menu. - NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu. - RESET : Resets the camera settings to the factory defaults. Language and Monitor settings are not initialized. ● The image on the screen is dim. ▶ Is lens stained with dirt? Clean your lens with soft, clean cloth. ▶ Set the monitor or DVR to proper condition. ▶ If the camera is exposed to very strong light, change the camera position. ● The image on the screen is dark. ▶ Adjust the contrast feature of the monitor or DVR. ▶ If you have an intermediate device, set the 75Ω / Hi-z properly. ● The camera is not working properly, and the surface of the camera is hot. ▶ Check that you have properly connected the camera to an appropriate power source. ● The DAY/NIGHT menu does not work. ▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’. ● The SENS-UP function does not work. ▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’. ▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’. ● The Motion Detection function does not work. ▶ Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’. ● Color is not correct. ▶ Check the setting of WHITE BAL SETUP menu . ● The screen flickers continually. ▶ Check that direction of camera turns toward the Sun. ● When coaxial communication is not available: ▶ Make sure that the camera and monitor are installed within the recommended distance. ▶ Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded. COLOR DOME CAMERA 30 User Guide COLOR DOME CAMERA 31 User Guide Dimension Specifications SCD-2020N ELECTRICAL Input Voltage Power Consumption VIDEO Imaging Device Total Pixels Effective Pixels Scanning System Synchronization Frequency Horizontal Resolution Min. Illumination S / N (Y signal) Video Output LENS Focal Length Angular Field of View PAN / TILT / ROTATE Pan / Tilt / Rotate Range OPERATIONAL Electronic Shutter Speed Shutter Mode On Screen Display Lens Shade SSDR Backlight Compensation Day & Night Gain Control White Balance SENS-UP Motion Detection Privacy Masking SSNR3 Digital Zoom DIS Camera Title Sharpness Flip / Mirror Communication ENVIRONMENTAL Operating Temperature / Humidity MECHANICAL Dimension / Weight SCD-2040N SCD-2021N SCD-2020P SCD-2040P SCD-2021P DC 12V ±10% / AC 24V ±10% Max 3.5W Ø107.6 1/3 inch, Diagonal 6mm Super HAD CCD 811(H) x 508(V) 795(H) x 596(V) 768(H) x 494(V) 752(H) x 582(V) 2:1 Interlace Internal / Line-Lock H : 15.734KHz V : 59.94Hz H: 15.625KHz V : 50.00Hz 600TVL 0.15 Lux (50IRE, @F1.2), 0.0003Lux (SENS-UP x512, @F1.2) 52dB (Weight On, AGC Off) CVBS : 1.0Vp-p, 75Ω composite 3.7mm 8.0mm 3.7mm+8.0mm 3.7mm 3.7mm : 71°(H), 52°(V) / 8mm : 33°(H), 25°(V) 8.0mm 83.7mm 3.7mm+8.0mm 5 R4 0° ~ 352° / 0° ~ 75° / 0° ~ 348° 1/60 ~ 1/120,000 sec ESC, A.FLK, Manual 1/50 ~ 1/120,000 sec English, Korean, Japanese, Spanish, French, Portuguese, Taiwanese English, Chinese, German, Italian, French, Spanish, Russian, Czech, Polish, Romanian, Serbian, Swedish, Danish, Turkish, Portuguese On / Off (Level adjustable) On / Off (Level adjustable) BLC / HLC / OFF COLOR / BW / AUTO (Electronic Type) Low / High / Off ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) Auto / Off (Selectable x2 ~ x512) On / Off (8 Programmable zones) On / Off (12 Programmable zones) On / Off (Level adjustable) On / Off (x1 ~ x16) On / Off On / Off (Displayed 15 Characters) On / Off (Level adjustable) On / Off Coaxial (Pelco Coaxitron) 81.6mm -10°C ~ +50°C / 30% ~ 80% RH Ø107.6 x 83.7mm / 285g ※ The specification for this product may change without prior notice for product improvement. COLOR DOME CAMERA 32 User Guide COLOR DOME CAMERA 33 User Guide DECLARATION OF CONFORMITY Application of Council Directive(s) MEMO 2004 / 108 / EC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-716 European Representative Name European Representative Address Equipment Type/Environment CCTV Camera Model Name SCD-2020P/2040P/2021P Beginning Serial NO. C3RL6V3Z100001X, C3RM6V3Z100001X, C3RN6V3Z100001X Year of Manufacture 2010.01.15 Conformance to EN 55022 : 2006 EN 50130-4 : 2003 We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s). Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe Signature Signature Full Name BONJENG GU Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON, KOREA Place Date 2010.01.15 Date COLOR DOME CAMERA 34 User Guide COLOR DOME CAMERA 35 User Guide SALES NETWORK • SAMSUNG TECHWIN CO., LTD. 145-3, Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea, 462-703 TEL : +82-31-740-8151~8 FAX : +82-31-740-8145 • AMSUNG TECHWIN AMERICA Inc. S 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com • AMSUNG TECHWIN EUROPE LTD. S Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS TEL : +44-1932-45-5300 FAX : +44-1932-45-5325 www.samsungtechwin.com www.samsungsecurity.com P/No. : Z6806-1111-01A VAN 10. 02
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Indoor & outdoor IP security camera
- CCD 25.4 / 3 mm (1 / 3")
- Wired
- Digital zoom: 16x
- Dome Ceiling
- Ivory
- 285 g
Related manuals
Frequently Answers and Questions
What are the system signals for SCD-2040?
The system signals available are NTSC and PAL.
Which type of camera mechanism is used in Samsung SCD-2040?
It has a 3-Axis camera mechanism.
What is the CCD type in SCD-2040?
The camera has a diagonal 6mm (1/3") 410,000 (NTSC) pixels, 470,000(PAL) pixels SONY CCD.
Does SCD-2040 support Lens Shading feature?
Yes, the LENS SHADE feature in SCD-2040 diminishes brightness contrast to obtain a balanced view.
What is the Day/Night mode in Samsung SCD-2040?
The camera has a Day & Night (Electronic type) feature that automatically selects the mode that is appropriate for daytime or nighttime conditions.