Sony SIR4260V User manual

High Resolution D/N IR Vandal Dome Camera SIR-4260V User Guide
Before installing and operating this product,
please read this manual thoroughly.
ENGLISH
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and correct input
power voltage. In order to that you can understand this manual thoroughly,
we will introduce our model description.
n SIR-4260 SERIES
• NTSC MODEL SIR-4260VN • PAL MODEL
SIR-4260VP
n MODEL DESCRIPTION
• SIR-4260VX_
SIGNAL SYSTEM
• SIGNAL SYSTEM
N → NTSC MODEL
P → PAL MODEL
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION -This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Features
Contents
• Features………………………………………………………………… 5
• Warnings & Cautions…………………………………………………… 6
• Precautions…………………………………………………………… 7
• Components and Accessories………………………………………… 8
• Overview… …………………………………………………………… 9
• Installation……………………………………………………………… 10
■ Installation… ………………………………………………………………… 10…
■ Adjust the panning, tilting and rotate mechanism while checking the position on the monitor…… 10…
■ Adjusting varifocal lens zoom and focus…………………………………… 12
• Connection……………………………………………………………… 12
■ Connecting To Monitor… ……………………………………………………
■ Connecting To Power…………………………………………………………
■ RS-485 communication control………………………………………………
■ Using Coaxial Communications………………………………………………
12…
13…
14…
15
• Operating Your Camera… …………………………………………… 16
■ Menu Configuration… ……………………………………………………… 16…
■ Menu Setup…………………………………………………………………… 17…
· LENS………………………………………………………………………… 18…
· EXPOSURE………………………………………………………………………18…
· WHITE BALANCE… ………………………………………………………… 20…
· SSDR……………………………………………………………………………21…
· BACKLIGHT… …………………………………………………………………21…
· SSNR3… …………………………………………………………………… 23…
· DAY/NIGHT…………………………………………………………………… 24…
· SPECIAL……………………………………………………………………… 26
· EXIT… …………………………………………………………………………31
• Troubleshooting………………………………………………………… 32
• Specifications…………………………………………………………… 33
• Dimension……………………………………………………………… 34
COLOR DOME CAMERA
4
User Guide
DAY&NIGHT(ICR)
Ultra High Sensitivity
The built-in high sensitivity CCD produces a
clear image even in 0Lux(B/W, IR-LED ON)or
lower illumination.
High Resolution
By adopting a diagonal 6mm(1/3") 410,000 (NTSC)
pixel, 470,000(PAL) pixel SONY CCD, the camera
produces clear picture quality with a horizontal
resolution of 600 TV lines for color and a horizontal
resolution of 700 TV lines for BW mode.
SSNR 3
(Samsung Super Noise Reduction)
The high-performance W-V DSP chip
effectively removes low-light gain noise and
ghosting to provide clear images even in dark
environments.
This camera has a function that automatically
selects the mode that is appropriate for daytime
or night-time conditions.
The COLOR mode operates in daytime conditions
to provide optimum colors, and BW mode
operates in night-time conditions to enhance the
definition of the image.
IR MODE Function
This function prevents the saturation of the
image by the IR illuminators at short distances.
Communication
RS-485, Coaxial communication methods are
supported.
- RS-485 Communications
:S
TW(SPD), Pelco-P, Pelco-D, Vicon,
Panasonic, Bosch, Honeywell, SEC
- Coaxial Communications
: Pelco Coaxitron
DIS (Digital Image Stabilizer)
The DIS function compensates for any camera
movement, to produce more stable pictures.
SSDR
(Samsung Super Dynamic Range)
OSD
The camera’s OSD is complimented by 18 languages.
- NTSC : Korean, English, French, Spanish, Japanese,
Portuguese, Taiwanese
- PAL : English, French, German, Spanish, Italian,
Chinese, Russian, Czech, Polish, Romanian,
Serbian, Swedish, Danish, Turkish, Portuguese
For images with high contrast between bright
and dark areas from difficult lighting
conditions such as backlighting, this camera
selectively illuminates darker areas while
retaining the same light level for brighter areas
to even out the overall brightness.
COLOR DOME CAMERA
Outdoor Visibility range 30M
The IR LEDs of the SIR-4260 automatically
illuminates viewing area in the extreme
darkness allowing the camera a long-range
visibility of up to 30 meters.
5
User Guide
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products.The Eco mark represents
Samsung Techwin’s will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Warnings & Cautions
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise. Please read it carefully and use the product accordingly.
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as
an aerial ladder while providing after-sales service shall be at your expense.
* Separate the power plug during a thunder storm.
* This product is only part of a surveillance system. Therefore, we can't compensate for material loss and/or personal
injuries by robbery, fire, natural disaster or something like this type.
Warning/Attention/Special Mark Messages
Ignoring this information may
result in material loss and/or
serious personal injuries including
death.
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates “Never Allowed.”
Indicates “No Disassembling.”
Use only under temperature conditions between
-10°C and +50°C. Provide good ventilation
when using in high temperature conditions.
Do not install under unstable
lighting conditions.
Severe lighting changes or flickering may
hinder normal camera operation.
Do not drop the camera or
subject it to physical shock.
May cause a product malfunction.
COLOR DOME CAMERA
6
User Guide
May lower image quality.
Avoid touching the camera lens.
The lens is the most important component
of the camera. Be careful not to smear it
with fingerprints.
Never keep the camera face to
strong light directly.
May damage the CCD.
COLOR DOME CAMERA
7
User Guide
Precautions
Overview
1
⓫
Do not expose the camera to
radioactivity.
2
3
Radioactivity exposure may damage the
CCD.
Notes
• Exposure to a spotlight or an object emitting strong light may cause smear or
blooming.
• Ensure that the power source complies with normal specifications before
supplying it to the camera.
• In case of IR LED has been lighted, do not lighten directly eye.
Components and Accessories
❶
6
2
7
3
4
8
❶ SIR-4260V
2 Instruction Manual 5 Wrench
6 Template
9 Installation Video Output Cable
5
9
3 Ø5 Tapping Screw 4EA 7 DC 12V/4A Adaptor
※ The set for America does not include the power adapter.
COLOR DOME CAMERA
8
User Guide
4 Quick Install Guide 8 POWER CABLE
5 4
6
7
8
❾
❿
Pan Base : control panning angle of camera
Rotate Base : control rotating angle of camera
X3.6 Vari-focal Lens Module
Flush Housing
Pan Base Holding Screws : fix panned position
Video output terminal
RS-485 Control terminal : The detailed decription refers to p14.
Power input terminal
Video Output Terminal to Monitor
Function Setup switch : display the menu on the screen and move the cursor to
four directions to confirm status or after changing a
selected item.
Dome Cover
COLOR DOME CAMERA
9
User Guide
Installation
Installation
Notes
• The installation should be done by qualified service personnel or system installers.
• If the ceiling material is not strong enough to hold the installation screws, the camera may
fall off. Reinforce the ceiling as needed.
• Take care not to drop the product during installation. Do not allow anyone to stand below the
installation area.
1) R
emove the dome cover and shield case from the main body by loosening the three
dome cover screws.
Mounting Bracket
Main Body(Camera)
1) You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism.
• Pan Base moves by 170° to each direction and 340° on the whole.
• Tilt Base covers total 146° angle(73° to each side).
• The angle range of the Rotate Base is the same as that of the Pan Base.But one
direction range is 195° and another is 145°
2) Methods of adjustment
• Wall installation
After mounting the camera to the wall, loosen the rotate base holding screws.
Adjust to the correct panning angle.
Then adjust the tilt angle by rotating the base.
Once complete re-tighten the rotate base holding screws.
• Ceiling installation
After mounting the camera to the ceiling, loosen the rotate base holding screws.
Adjust to the correct panning angle.
Then adjust the tilt angle by rotating the base.
Once complete re-tighten the rotate base holding screws.
Notes
Dome Cover
2) A
nd then remove the main body from the mounting bracket by the four main body screws.
Adjust the panning, tilting and rotate mechanism while checking the position on the monitor
•When adjusting the rotating angle, loosen rotate base holding screw as follows Figure A. And
then tighten it again.
•When adjusting the tilting angle, grip the tilt base and adjust tilting angle.
•When adjusting the panning angle, loosen pan base holding screws as the follows Figure B.
And then tighten them again.
•The 2 LED sections can be tilted inside the case to a maximum angle of 73°, this however
will not alter the illuminated range.
Rotate Base Holding Screw
73°
145°
195°
Rotate Base
Tilt Base
170°
Pan Base
Pan Base Holding Screw
Rotate Base Holding Screw
• When adjusting the tilt mechanism hold the Tilt base and NOT the lens.
-170°
COLOR DOME CAMERA
10 User Guide
COLOR DOME CAMERA
11 User Guide
Installation
Connecting to Power
Adjusting varifocal lens zoom and focus
1) Unlock the zoom (focus) handle by turning anti-clockwise.
2) Adjust the zoom (focus) by moving the handle to WIDE (NEAR) or TELE (FAR).
3) After adjustment, tighten the zoom (or the focus) handle, taking care that the adjusted
position does not change.
The recommended adaptor specification for
SIR-4260V is DC 12V/4A.
Please check the standard power requirement
before connecting the power.
Focus Handle
Zoom Handle
When the resistance value of copper wire is at [20°C(68°F)]
Copper wire size(AWG)
Connection
Resistance value(Ω/m)
Voltage drop(V/m)
Connecting to Monitor
Please connect the video output terminal located on the back of the camera to the monitor.
• The connection method varies depending on the type of monitor and accessories. Please
refer to the user's manual for each instrument.
• Please turn off the power when connecting.
• Please select Hi-Z on the 75Ω/Hi-Z switch for the intermediate video TV set and select
75Ω for the Intermediate device as shown in the picture below.
#24(0.22㎟)
0.078
0.028
#22(0.33㎟)
0.050
0.018
#20(0.52㎟)
0.030
0.011
• Therefore having an excessively long distance between the power adaptor and the
camera may affect the camera’s performance.
※ Standard voltage for camera operation : DC 12V±10%, AC 24V±10%
※ There may be some deviation in voltage drop depending on the type of wire and the
manufacturer.
※ The set for America does not include the power adapter.
Intermediate End monitor
Notes
CCTV Camera
Monitor
COLOR DOME CAMERA
CCTV Camera
12 User Guide
#18(0.83㎟)
0.018
0.006
• Please use a power adapter that meets the required standards.
• Please connect the power after installation.
COLOR DOME CAMERA
13 User Guide
Connection
Using Coaxial Communications
RS-485 communication control
• Coaxial Communications System
• OSD Control method
Connecting to RS-485 Control Cable
WHITE (TRX+)
BLACK (TRX-)
CONTROL CABLE
SPEC
WHITE (TRX+)
RS-485+
BLCAK (TRX-)
RS-485-
Using RS-485 communication will enable you to control the OSD menu from a SAMSUNG
TECHWIN System Controller or DVR.
(1) Connection to a PC.
Connect the camera to the PC via a RS-485 converter using RS-485 and a serial cable.
CAMERA
DVR
CONTROLLER
SET
UP
DOWN
LEFT
RIGHT
MENU / ENTER UP KEY
DOWN KEY LEFT KEY
RIGHT KEY
OSD KEY
JOYSTICK UP
JOYSTICK DOWN
JOYSTICK LEFT
JOYSTICK RIGHT
DVR
DVD
EX) SERIAL PORT OF THE PC(COM1) → SERIAL CABLE → RS-485 CONVERTER → RS-485
CONTROL CABLE
(2) Connection to a DVR or System Controller.
Connect the RS-485 cable to the connection ports of the DVR or System Controller.
485 Control Board Connection Port
RS-485 Control Port
(+) CONNECTION TERMINAL
(-) CONNECTION TERMINAL
WHITE (TRX+)
BLACK (TRX-)
* RS-485 Communication establishment initial value
Item
Initial value
Camera ID
BAUD RATE
UART MODE
RET PKT
1
9600
8-NONE-1
ENABLE
• : BNC
• ----: RS-485
– Video Cable
The camera's video output port is connected to the monitor with a BNC coaxial cable,
shown below : If the distance between the camera and the monitor exceeds the
recommended maximum, please use an auxiliary video amp.
Distance Recommended Cable Specification
300m
3C2V(RG-59/U)
450m
5C2V(RG-6/U)
600m
7C2V(RG-11/U)
Notes
• When making a control system to control the camera, please use to the STW(SPD)
PROTOCOL or PELCO-P, PELCO-D, VICON, PANASONIC, BOSCH, HONEYWELL, SEC
PROTOCOL.
• When you connecting to RS-485 control cable, please peel off the outer skin inside the
RS-485 control cable.
• In case of SCC-101 connection, change communication mode to『8-E-1』at
『Communication configuration』menu. (For more information, refer to SCC-101 manual.)
COLOR DOME CAMERA
14 User Guide
Notes
• If the camera is controlled through coaxial communication, please use a video amp intended
for coaxial communications. Regular video amps do not transfer coaxial signals.
COLOR DOME CAMERA
15 User Guide
Operating Your Camera
Menu Configuration
Menu Setup
Use the Function Setup switch whithin the camera.
MAIN SETUP MENU
LENS
●DC
EXPOSURE
●BRIGHTNESS
●SENS-UP
●SHUTTER ●AGC ●RETURN
WHITE BAL
●ATW
●MANUAL
●OUTDOOR
●AWC→SET
SSDR
●OFF
●ON
BACKLIGHT
●OFF
●BLC
SSNR3
●OFF
●ON
●INDOOR
Function Setup switch
●HLC
1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
DAY/NIGHT
●COLOR
●B/W
●AUTO
SPECIAL
●IMAGE ADJ
●MOTION DET
●COMM ADJ
●CAM TITLE
●PRIVACY
●LANGUAGE
●SYNC
●DIS
●RETURN
EXIT
●SAVE
●NOT SAVE
●RESET
Select the function using
the Function Setup switch.
MAIN SETUP
1.LENS
DC
2.EXPOSURE 3.WHITE BAL
ATW
4.SSDR OFF
5.BACKLIGHT
OFF
6.SSNR3
ON
7.DAY/NIGHT
AUTO
8.SPECIAL 9.EXIT
SAVE
Change the status using the
Function Setup switch.
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
Notes
• An item with the icon also has sub menus. To select a sub menu, select an item with the
icon and press the Function Setup switch.
• An item with the - - - icon is unavailable due to function settings.
COLOR DOME CAMERA
16 User Guide
COLOR DOME CAMERA
17 User Guide
Operating Your Camera
LENS
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed, select‘LENS’by using the Function Setup
switch so that the arrow indicates‘LENS’.
2. DC
: You can adjust the minimum shutter and maximum value of ESC shutter mode.
MAIN SETUP
1.LENS
2.EXPOSURE DC
3. The Lens mode has sub menu items as listed below.
- BRIGHTNESS : Adjusts the video brightness.
- FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the Focus Settings mode
under each lens menu. Activate the Focus Settings mode, adjust the lens focus,
and then deactivate the settings mode.
SHUTTER : You can select the shutter.
- --- : Shutter speed is fixed at 1/60sec(1/50sec)
- ESC : Select this to control the shutter speed automatically. If ESC is selected, the
shutter speed is automatically controlled depending on the ambient
illumination of the subject.
- MANUAL : You can control shutter speed manually.
(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)
- A.FLK : Select this when you see picture flicker, this can happen when the frequency
of the local lighting clashes with the camera.
Notes
• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but the
higher the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 5.3dB to 32dB.
- HIGH : Allows automatic gain control from 5.3dB to 37dB.
EXPOSURE
MAIN SETUP
1.LENS
2.EXPOSURE 3.WHITE BAL
DC
ATW
1. When the SETUP menu screen is displayed, select ‘EXPOSURE’ by using the Function Setup switch.
2. Select a desired mode using the Function Setup switch.
EXPOSURE SETUP
1.BRIGHTNESS
2.SHUTTER
3.AGC
4.SENS-UP
5.RETURN
COLOR DOME CAMERA
25
--HIGH
OFF
18 User Guide
SENS-UP : When it is night or dark, the camera automatically detects the light level and
maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP
menu.
Notes
• If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by
increasing or decreasing the shutter speed. (x2 ~ x512)
• Note that the higher the zoom level, the brighter the screen, but the more likely there will be
a ghosting effect.
• It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode when the
D-zoom level is increased.
COLOR DOME CAMERA
19 User Guide
Operating Your Camera
White Balance (White Bal)
SSDR (Samsung Super Dynamic Range)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function Setup
switch so that the arrow indicates ‘White Bal’ .
2. Select a desired mode using the Function Setup switch.
SSDR illuminates darker spots of an image while retaining the same light level for brighter
spots to even out the overall brightness of images with high contrast between bright and
dark spots.
MAIN SETUP
1.LENS
2.EXPOSURE 3.WHITE BAL
4.SSDR DC
ATW
OFF
※ Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K.
OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.
(sodium light inclusion)
INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by
using the ATW or AWC mode. After that switch to MANUAL mode, finetune the White Balance and then press the Function Setup switch.
AWC →SET : To find the optimal luminance level for the current environment, point the
camera towards a sheet of white paper and press the Function Setup
switch. If the environment changes, readjust it.
Notes
• White Balance may not work properly under the following conditions. In this case select the
AWC mode.
When the color temperature of the environment surrounding the subject is out of the control
range (e.g. clear sky or sunset).
When the ambient illumination of the subject is dim.
If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
COLOR DOME CAMERA
20 User Guide
MAIN SETUP
1.LENS
2.EXPOSURE 3.WHITE BAL
4.SSDR 5.BACKLIGHT
DC
ATW
OFF
OFF
1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the switch so that the
arrow indicates ‘SSDR’.
2. Use the switch to change the SSDR level according to the contrast between bright and dark areas.
SSDR ON
SSDR OFF
BACKLIGHT
Unlike conventional cameras, the SIR-4260V is designed to deliver a distinctive subject and
background at the same time, even when the subject is backlight, by using the features of the
proprietary W-V DSP chip.
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function Setup
switch so that the arrow indicates ‘BACKLIGHT’.
COLOR DOME CAMERA
21 User Guide
Operating Your Camera
MAIN SETUP
1.LENS
2.EXPOSURE 3.WHITE BAL
4.SSDR 5.BACKLIGHT
6.SSNR3
Notes
• Because there can be a difference in the effectiveness of HLC according to the amount of
light area in the screen, optimize the installation angle for the best HLC performance.
• When dark, the HLC is only activated when a bright light exceeding a specific size in NIGHT
ONLY mode.
• The HLC is not activated in day light or when bright light is not present at night in NIGHT
ONLY mode.
• BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.
DC
ATW
OFF
OFF
ON
2. Select a desired mode using the Function Setup.
BLC : Enables a user to directly select a desired area from a picture, and to view the
area more clearly.
HLC (High Light Compensation) : If the scene contains extremely bright light areas such as; from car headlights, the light
can mask out much of the on-screen detail.
- LEVEL : Adjust level of the HLC function.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / transparency of the masking area.
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced
SSNR3
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select ‘SSNR3’ by using the Function Setup
switch so that the arrow indicates ‘SSNR3’.
OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the Function Setup switch.
Select ‘BLC’ to adjust the area to be
HLC : Enable the user to change the level,
enhanced then adjust the level.
limit, mask color/tone and area.
MAIN SETUP
1.LENS
DC
2.EXPOSURE 3.WHITE BAL
ATW
4.SSDR OFF
5.BACKLIGHT
OFF
6.SSNR3
ON
7.DAY/NIGHT
AUTO
2. Select a desired mode using the Function Setup switch.
OFF: Deactivates SSNR3. Noise is not reduced. ON : Activates SSNR3 so that noise is reduced. 3. Set the SSNR3 mode to ‘ON’ and press the Function Setup switch. Then you can adjust the
noise reduction level.
LOW
120
5
172
COLOR DOME CAMERA
22 User Guide
Notes
• You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is
‘OFF’.
• When adjusting the noise reduction level in the SSNR mode, remember that the higher the
level set, the more the noise level will be reduced, as will the brightness of the image.
COLOR DOME CAMERA
23 User Guide
Operating Your Camera
DAY/NIGHT
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Function Setup
switch so that the arrow indicates ‘DAY/NIGHT’ .
- BURST MODE : You can turn on or off the burst signal on
B/W mode.
- DURATION : You can select brightness of illumination about changing the day/night mode.
- DWELL TIME : You can select the duration time about changing the day/night mode. …
→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
Color ➞ B/W
B/W ➞ Color
2.5 lux
1 lux
5 lux
10 lux
Fast
Slow
MAIN SETUP
1.LENS
DC
2.EXPOSURE 3.WHITE BAL
ATW
4.SSDR OFF
5.BACKLIGHT
OFF
6.SSNR3
ON
7.DAY/NIGHT
AUTO
8.SPECIAL * The day/night switching point of the
camera can be adjusted.
Notes
• When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR'
mode and 'AUTO' mode can not be selected.
2. Select a desired mode using the Function Setup switch according to the picture display you want.
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
- IR MODE : When IR LED is turned on in B/W, the objects can
be clearly identified due to the function that
decreases screen saturation of objects within a
short distance.
· TOP/BOTTOM/LEFT/RIGHT : Adjust the range according to
the location of objects.
- IR LEVEL : Select LOW when objects appears within a short distance or select HIGH when
objects appears within a long distance on the screen.
AUTO: The mode is switched to ’Color‘ in a normal
environment, but switches to ’B/W‘ mode when
ambient illumination is low. To set up the switching
time for AUTO mode, press the Function Setup
switch. You can turn on or off the burst signal on
B/W mode.
COLOR DOME CAMERA
24 User Guide
AUTO SETUP
▶1.BURST MODE
2.COLOR->B/W
DURATION
DWELL TIME
3.B/W->COLOR
DURATION
DWELL TIME
4.RETURN
ON
FAST
3SEC
FAST
10SEC
COLOR DOME CAMERA
25 User Guide
Operating Your Camera
SPECIAL
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup
switch so that the arrow indicates ‘SPECIAL’.
MAIN SETUP
1.LENS
DC
2.EXPOSURE 3.WHITE BAL
ATW
4.SSDR OFF
5.BACKLIGHT
OFF
6.SSNR3
ON
7.DAY/NIGHT
AUTO
8.SPECIAL 9.EXIT
SAVE
2. Select a desired mode using the Function Setup switch.
1.
2.
3.
4.
5.
6.
7.
8.
9.
SPECIAL
IMAGE ADJ CAM TITLE
OFF
SYNC
INT
MOTION DET
OFF
PRIVACY
OFF
DIS
OFF
COMM ADJ
LANGUAGE
ENGLISH
RETURN
COLOR DOME CAMERA
26 User Guide
IMAGE ADJ :
1) When the SETUP menu screen is displayed, select ‘IMAGE ADJ’ by using the Function
Setup switch so that the arrow indicates ’IMAGE ADJ‘.
2) Select a desired mode using the Function Setup switch.
1.
2.
3.
4.
5.
6.
7.
IMAGE SETUP
V-REV
H-REV
D-ZOOM
FONT COLOR
SHARPNESS
MONITOR RETURN
OFF
OFF
OFF
WHITE
ON
LCD
• V-REV : You can flip the picture vertically on the screen.
• H-REV : You can flip the picture horizontally on the screen.
• D-ZOOM : You can use a digital zoom of x1 ~ x16.
• FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue)
• SHARPNESS : As you increase this value, the picture outline becomes stronger and
clearer. Adjust this value appropriately
depending on the sharpness of the
picture.
• Monitor : Please change the settings value of video
appropriate to your monitor.
- LCD : Please select this menu item when using a LCD
monitor.
- CRT : Please select this menu item when using a CRT monitor.
- USER : Please use this menu item when using a monitor other than standard ones. You
can change the gamma, PED level, and color gain in the sub menus.
• RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to
the SETUP menu.
Notes
• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
• If you increase the SHARPNESS level too high, the picture may become distorted or noise
may appear.
COLOR DOME CAMERA
27 User Guide
Operating Your Camera
CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow
indicates ‘CAM TITLE’.
2) Set it to ‘ON’ by using the Function Setup switch.
3) Press the Function Setup switch.
4) Use the Function Setup switch to move to
a desired letter and select the letter by pressing
the Function Setup switch. Repeat this to enter
multiple letters. You can enter up to 15 letters.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
←→CLR POS END
Notes
5) Enter a title, move the cursor to ‘POS’ and
press the Function Setup switch. The entered
title appears on the screen. Select the position to
display the title on the screen by using the Function
Setup switch and press the Function Setup switch.
When the position is determined, select ‘END’ and
press the Function Setup switch to return to the
SPECIAL menu.
FRONT DOOR
Notes
• When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if
you enter one.
• Only English is available in this mode.
• If you move the cursor to CLR and press the Function Setup switch, all the letters are
deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function
Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be
inserted and then press the Function Setup switch.
COLOR DOME CAMERA
28 User Guide
SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL),
you can synchronize the output phase of multiple
cameras using the power synchronization function
(Line-Lock) without using a synchronization signal
generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select 'phase'.
• When using AC power at 60Hz(NTSC), 50Hz(PAL) frequency, you can use the L/L type
synchronization.
• When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
MOTION DET : This product has a feature that allows you to observe
movement of objects in 8 different areas on the screen, and
the words 'MOTION DETECTED' appear on the screen when
movement is detected.
Activity can be monitor more efficiently.
1) When the SPECIAL menu screen is displayed, press the
Function Setup switch so that the arrow
indicates‘MOTION DET’.
2) S et up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion
detection sensitivity is increased to recognize even small movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- FILL→SET : Fills in a selected MD area. The color of the area can be selected from brown,
orange, blue, cyan, green, yellow, magenta and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.
COLOR DOME CAMERA
29 User Guide
Operating Your Camera
PRIVACY :Mask an area you want to hide on the screen.
1.
2.
3.
4.
5.
6.
7.
8.
9.
PRIVACY AREA SETUP
AREA
AREA1
MODE
OFF
MASK COLOR
GREEN
MASK TONE
1
TOP
39
BOTTOM
79
LEFT
13
RIGHT
52
RETURN
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the
arrow indicates ‘PRIVACY’.
2) Set up the mode using the Function Setup switch.
- AREA : You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area selected in the AREA.
- MASK COLOR :Determine area color. You can select Green, Red, Blue, Black, White, Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.
COMM ADJ (Communication Adjustment) :
This function sets up the camera communication status when controlling the camera
through an external control device.
1) When the SPECIAL menu screen is displayed, press the
Function Setup switch so that the arrow indicates
‘COMM ADJ’.
2) Set up the mode using the Function Setup witch.
- CAM ID : D etermines the camera's identification
number (between 0 and 255).
- BAUD RATE : You can select 2400/4800/9600/19200/
38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD for
the parity bits.
- RET PKT : Determines whether to send a command back to the controller device when a
communication control command is sent to the camera.
- DISP CAM ID : D
isplay camera title on top left corner of the screen.
- Protocol : Select the communication PROTOCOL.
(STW(SPD)/PELCO-D/PELCO-P/BOSCH/HONEYWELL/VICON/SEC/PANASONIC)
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
* Initial value of communication adjustment
Item
Initial value
Camera ID
1
BAUD RATE UART MODE
9600
8-NONE-1
PET PKT
ENABLE
LANGUAGE : You can select the menu language according to your requirements.
RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
EXIT
Notes
• As the DIS function uses the digital zoom the camera's resolution will decrease.
• DIS doesn’t operate when background illumination is too low.
• DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
COLOR DOME CAMERA
30 User Guide
Select a desired EXIT mode using the Function Setup switch.
- SAVE : Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
- RESET : R esets the camera settings to the factory defaults. Language, Communication and Monitor
settings are not initialized.
COLOR DOME CAMERA
31 User Guide
Troubleshooting
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
•N
othing appears on the screen.
▶Check that the power cord and line connection between the camera and monitor are
fixed properly.
▶Check that you have properly connected UTP cable or BNC cable to the camera.
• The image on the screen is dim.
▶Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶Set the monitor to proper condition.
▶If the camera is exposed to too strong light, change the camera position.
• The image on the screen is dark.
▶Adjust the contrast feature of the monitor.
▶If you have an intermediate device, set the 75Ω / Hi-z properly.
• The camera is not working properly, and the surface of the camera is hot.
▶Check that you have properly connected the camera to an appropriate power source.
• The SENS-UP function does not work.
▶Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
• The Motion Detection function does not work.
▶Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
• Color is not correct.
▶Check the setting of WHITE BAL SETUP menu .
• The screen flickers continually.
▶Check that direction of camera turns toward the Sun.
• When coaxial communication is not available:
▶Make sure that the camera and monitor are installed within the recommended distance.
▶Use the video amplifier equivalent to coaxitron if the recommended installation distance
is exceeded.
Specifications
SIR-4260VN
ELECTRICAL
Input Voltage
Power Consumption
VIDEO
Imaging Device
Total Pixels
Effective Pixels
Scanning System
Synchronization
Frequency
Horizontal Resolution
Min. Illumination
Visibility distance(IR LED)
S/N (Y Signal)
Video Output
LENS
Zoom Ratio
Focus Length
Angular Field of View
PAN / TILT / ROTATE
Pan / Tilt / Rotate Range
OPERATIONAL
Electronic Shutter Speed
On Screen Display
SSDR
Backlight Compensation
Day & Night
Gain Control
White Balance
SENS-UP (frame Integration)
Motion Detection
Privacy Masking
3D Noise Filter (SSNRIII)
Digital Zoom
Digital Image Stabilization(DIS)
Camera Title
Sharpness
Flip / Mirror
Communication
Protocol
ENVIRONMENTAL
Operating Temperature / Humidity
MECHANICAL
Water Resistance
Dimension (Weight)
SIR-4260VP
DC 12V ± 10% / AC 24V ± 10%
Max 5W (LED ON)
1/3 inch, Diagonal 6mm Super HAD CCD
811(H) x 508(V)
795(H) x 596(V)
768(H) x 494(V)
752(H) x 582(V)
2:1 Interlace
Internal /Line-Lock
H : 15.734KHz V : 59.94Hz
H : 15.625KHz V : 50.00Hz
COLOR : 600TVL, B/W : 700TVL
LED ON : 0Lux / LED OFF : 0.15Lux(Color, F1.2), 0.0003Lux(Color,SENS-UP x512)
30m(10EA)
52dB (Weight On, AGC Off)
CVBS : 1.0Vp-p, 75Ω composite
3.6x (Manual)
2.8 ~ 10.0mm (F1.2)
H : 94.4°(Wide) ~ 28°(Tele) / V : 69.2°(Wide) ~ 21°(Tele)
0°~ 340°/ 0°~ 146°/ 0°~ 340°
1/60 ~ 1/120k sec
1/50 ~ 1/120k sec
NTSC : 7 Languages, PAL : 15 Languages
On / Off (Level adjustable)
BLC / HLC / OFF
COLOR / B/W / AUTO (ICR)
Low / High / Off
ATW /Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto /Off (Selectable x2 ~ x512)
On / Off (8 Programmable zones)
On / Off (12 Programmable zones)
On / Off (Level adjustable)
On / Off (x1 ~ x16)
On / Off
On / Off (Displayed 15 Characters)
On / Off (Level adjustable)
On / Off
Coaxial, RS-485
Coaxial(Pelco), RS-485(STW(SPD), PELCO-P, PELCO-D, VICON, PANASONIC, BOSCH,
HONEYWELL, SEC)
-10°C ~ +50°C / 30% ~ 80% RH
IP66
Ø148 x 126mm (1.3Kg)
※ T he specification for this product may change without prior notice for product improvement.
COLOR DOME CAMERA
32 User Guide
COLOR DOME CAMERA
33 User Guide
DECLARATION OF CONFORMITY
Dimension
Ø 148mm
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
126mm
European Representative Name
European Representative Address
85mm
Equipment Type/Environment CCTV Camera
Model Name SIR-4260VP
Beginning Serial NO. C10S7010007
Year of Manufacture 2009.07.03
Conformance to EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
83.5mm
85mm
COLOR DOME CAMERA
34 User Guide
46mm
85mm
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name BONJENG GU
Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON, KOREA
Place
Date 2009.07.03
Date
COLOR DOME CAMERA
35 User Guide
SALES NETWORK
•
AMSUNG TECHWIN CO., LTD.
S
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : +82-31-740-8151~8 FAX : +82-31-740-8145
•
AMSUNG TECHWIN AMERICA Inc.
S
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
•
AMSUNG TECHWIN EUROPE CO., LTD.
S
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungcctv.com
P/No. : Z6806-1028-02B
VAN 09.10
">