ECHO CSV-5, CSV-5S, CSV-8S Chipper/Shredder/Vacuum Operator's Manual

 ECHO —
( TS в
| Chipper/Shredder/Vacuum
Operator's Manual
MODELS: CSV-5 (Walk Behind)
CSV-5S (Self Propelled)
CSV-8S (Self Propelled)
\ J
4
WARNING A DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and an
Engine Operators Manual. Both must be read and understood for proper and safe operations.
N ”
For your nearest ECHO Dealer, call 1-800-432-ECHO (3246)
2UECHO
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-
« dependability. Read and understand this manual and the important Safety Messages it contains.
A CAUTION A
Read rules for safe operation and instructions carefully. ECHO provides an Operators Manual and an Engine Manufacturer's
Operators Manual that must be read and understood for proper and safe operation.
7
The Operator's Manual --
contains important SAFETY information plus, specifications and
information for operation, starting, stopping, maintenance, storage and
assembly of the Unit. Also included is the Engine Manufacturer's
Operator's Manual and Transmission Warranty Statement which must also
be read and understood.
Operators and Parts Manuals --
are available for purchase from your ECHO dealer or directly from ECHO.
See ordering instructions at the end of this manual.
Specifications, descriptions and illustrative material in this literature are | |
as accurate as known at the time of publication, but are subject to WA В À | № ©
change without notice. Illustrations may include optional equipment The engine exhaust from this
and accessories, and may not include all standard equipment. product contains chemicals
known to the State of California
to cause cancer, birth defects or
other reproductive harm.
« Copyright O 1995 ECHO, INCORPORATED J
CHIPPER/SHREDDER/VACUUM
OPERATOR'S MANUAL
3
/
TABLE OF CONTENTS
~
or CAUTION calls attention to an act or condition that can lead
to serious personal injury to operator and bystanders.
The circle with the slash symbol means whatever is shown
within the circle is prohibited.
Q This symbol accompanied by the words WARNING, DANGER
IMPORTANT The enclosed message provides information necessary
for the protection of the unit.
INTRODUCTION ..................eemecció e … 2 OPERATION
Safety Symbols........................eei eee 3 Stationary Shredding/Chipping........................ 18
Operator Safety euere 4 Mobile-Vacuuming Leaves............................. 19
PRE-OPERATION Mobile-Blowing..............e....... mena 20
Equipment Check......................... e 5
Determine Operation Area......................—.......... 6 MAINTENANCE
Operation Safety Tips eeccararenonororoacoreerervercevecaemos 6 Cleaning pervorooeorouocuocarcanoareotostrreaoooracareamenrarere. 21
Description essen eee eee. 9 Lubrication...............—......mee eee 22
ASSEMBLY Replacing/Sharpening Chipper Knives ............ 23
Install Front Wheels ......................... in. 12 Replacing Hammers.................—— me... 25
Install Rear Wheels are 12 Drive Belt Replacement.......................e....... 26
Install Upper Handle Bar ................................ 13 Storage .................eceirerenercenc ecc ene nee. 28
Install Wheel Guard Kit 13 Servicing Information ................—......—.0-.......... 29
Install Traction Control... 14 SPECIFICATIONS …….….………ercrerrerrrersreassensrssrrrersa rennes 30
Install Height Control... 14 DECALS coir 31
Install Shredding Hopper ............................... 16
Install Discharge Elbow & Collection Bag ...... 16
Prepare Engine for Operation .......................... 16
N и
( в
SAFETY SYMBOLS
Throughout this manual and on the product itself, you will find safety alerts
and helpful, informational messages preceded by symbols or key words. The
following is an explanation of those symbols and key words and what they г; CAUTION
mean to you. Фо я
{>
AW, Vo
NOTE This enclosed message provides
tips for use, care and maintenance of the
unit.
ТЕТЕ
7
OPERATOR SAFETY
A CAUTION
Operators risk injuries to themselves and others if the unit is used improperly and or safety precautions are not
followed. Proper clothing and safety gear must be worn when operating the unit.
Eye Protection --
Eye protection goggles that meet ANSI Z87.1 requirements were included
With your unit. Wear these goggles whenever you operate the unit.
Hearing Protection --
Always wear hearing protection when using this unit. Noise is created by
the engine and the internal workings of the machine as it chips and shreds
the material. Hearing protection devices are available from your ECHO
Dealer.
Proper Clothing --
Wear snug fitting, durable clothing;
-Pants should have long legs, shirts longsleeves.
-DO NOT WEAR SHORTS,
-DO NOT WEAR TIES, SCARVES, JEWELRY.
Wear sturdy work shoes with non-skid soles;
-DO NOT WEAR OPEN TOE SHOES,
-DO NOT OPERATE UNIT BAREFOOTED.
Hot Humid Weather --
Heavy protective clothing can increase operator fatigue which may lead to
heat stroke. Schedule heavy work for early morning or late afternoon hours
when temperatures are cool.
CHIPPER/SHREDDER/VACUUM 5
OPERATOR'S MANUAL
NN
HANDLING FUEL
x
AA caution
Fuel is VERY flammable. Use extreme care when storing or handling.
- Use an approved fuel container.
- DO NOT smoke near fuel.
- DO NOT allow flames or sparks near fuel.
- Fuel tanks/cans may be under pressure. Always loosen fuel caps
slowly allowing pressure to equalize.
- NEVER refuel a unit when the engine is HOT!
- NEVER refuel a unit with the engine running.
- DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors
over bare ground.
After Refueling;
- Wipe any spilled fuel from the unit.
- Move at least 10 ft. (3 M) from refueling location before starting.
IMPORTANT — This product is powered by a 4 (four) Stroke
Engine. DO NOT mix oil and fuel together. Refer to Engine
Manufacturer's Operators Manual for fueling instructions.
10 feet (3m)
Physical Condition --
Your judgment and physical dexterity may not be good:
-if you are sick,
-if you are taking medication,
-if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
7
Equipment Check —
Before operation a complete check of the unit must be performed;
- Check unit for loose/missing nuts, bolts and screws. Tighten and/or
replace as needed.
A CAUTION
Inspect fuel lines, tank and area around carburetor for fuel leaks.
DO NOT operate unit if leaks are found.
БЕСТ
- Inspect belt guard (A), transmission cover (B) and belt (self propelled
unit only). Belt guard and transmission cover must be in place. Do
not operate machine if belt guard is damaged or missing. Do not
operate machine if transmission cover is damaged or missing.
- Hopper Baffle (A), Chipper Chute Guard (B) and Grate Bar (located
inside discharge elbow) MUST be in place and in good repair.
NEVER operate unit if any are damaged or missing.
EP
ER EET
14 -
\
4 Determine Operation Area —
Vacuuming - Walk Behind
- Review the area to be vacuumed. Look for hazards that could
contribute to unsafe conditions. Loose stones, toys, wire and other
objects that may be drawn into the unit should be removed. Steep
slopes and uneven terrain should be avoided.
- Spectators and fellow workers must be warned and children and
animals prevented from coming nearer than 50 ft. (15m) while the
unit is in use.
Shredding/Chipping Stationary
- For stationary use, this machine should be operated only on a solid,
flat, level surface. Select the area of operation carefully. Avoid areas
where spectators, fellow workers, children or animals are common.
- If used without the Collection Bag, position the machine with the
Optional, Discharge Chute Extension aimed into a confined, protected
area.
N
@ Operation Safety —
- Do not allow children to operate this equipment.
- Before starting the unit, equip yourself and any other person working
within the 50 ft. (15m) Safety Zone with the proper Protective
Equipment and clothing.
- Know where the engine controls are and how to use them. Know and
practice an Emergency Shutdown Procedure. See Engine
Manufacturer's Operators Manual for specific information.
IDLER=IFAST
) OFF [pmON
Con —
O | | |
``
CHIPPER/SHREDDER/VACUUM
OPERATOR'S MANUAL
A CAUTION
Under normal shut down circumstances (engine shut down and
stopped), the Shredding/Chipping Rotor will continue to turn for
approximately twenty (20) seconds. Not waiting for rotor to stop
may cause serious personal injury.
NEVER place your hands, any part of your body or clothing inside the
Shredding Hopper, Discharge Elbow or Chipper Chute unless the
engine is shut off, the spark plug wire is disconnected and the wire is
moved away from the plug to prevent accidental starting, and the rotor
has come to a complete stop.
Do Not run engine in an enclosed area. Exhaust fumes contain carbon
monoxide which is a colorless, odor free, tasteless deadly Poison.
Stand back and to the side of the Shredding Hopper, Chipping Chute
and Discharge Elbow when material is placed in the machine for
processing.
Do not over reach when using this unit. Always maintain proper
balance and footing at all times.
During operation, the complete unit, especially the muffler and engine
become very hot, too hot to touch. Avoid contact during and
immediately after operation.
Watch for and remove any material that may accumulate on the
muffler or build up in the Discharge Chute during operation.
DO NOT move machine with the engine running unless you are
Vacuuming or Blowing.
Material fed into this machine must be shreddable. Metal, rocks,
bottles or other non-shreddable material WILL damage the machine
and can result in serious personal injury.
If non-shreddable material is fed into the machine, the machine jams
or makes unusual noise or vibrates, IMMEDIATELY STOP the unit.
Disconnect the spark plug and move it away from the spark plug to
prevent accidental starting. Refer to Removing aJam in the
Maintenance Section.
Mish!)
hs
7
ВЕСТ
- Before starting your unit, disconnect the spark plug wire and move it
away from the spark plug to prevent accidental starting. Inspect the
Shredding Hopper, Shredding Chamber, Chipper Chute and Discharge
Elbow. Items (garden tools, gloves etc.) left in these areas will either
jam the machine or be destroyed.
N
Vibration and Cold --
It is believed that a condition called Raynaud’s Phenomenon, which affects
the fingers of certain individuals may be brought about by exposure to
vibration and cold. Exposure to vibration and cold may cause tingling and
burning sensations followed by loss of color and numbness in the fingers.
The following precautions are strongly recommended because the minimum
exposure which might trigger the ailment is unknown.
- Keep your body warm, especially the head, neck, feet, ankles,
hands and wrists.
- Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
- Limit the hours of operation. Try to fill each day with jobs where
operating this product or other hand-held power equipment is not
required.
- If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries --
It is believed that overusing the muscles and tendons of the fingers, hands,
arms and shoulders may cause soreness, swelling, numbness, weakness and
extreme pain in those areas. Certain repetitive hand activities may put you at
a high risk for developing Repetitive Stress Injury (RSI). An extreme RSI
condition is Carpal Tunnel Syndrome (CTS), which could occur when your
wrist swells and squeezes a vital nerve that runs through the area. Some
believe that prolonged exposure to vibration may contribute to CTS. CTS
can cause severe pain for months or even years. To reduce the risk of RSI/
CTS, do the following:
- Avoid using your wrist in a bent, extended or twisted position.
Instead try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index finger. Take
periodic breaks to minimize repetition and rest your hands.
- Reduce the speed and force in which you do the repetitive movement.
- Do exercises to strengthen the hand and arm muscles.
- See a doctor if you feel tingling, numbness or pain in the fingers,
« hands, wrists or arms. The sooner RSI/CTS is diagnosed, the more
likely permanent nerve and muscle damage can be prevented.
CHIPPER/SHREDDER/VACUUM
9
OPERATOR'S MANUAL
DESCRIPTION
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.
Use the contents list to
Contents List
[] QTY DESCRIPTION [] 1 Parts Bag
[ ] 1 Base Unit Assembly CSV-5
[] 1 Hopper -[] 4
[] 1 Discharge Elbow -[] 3
[] 1 Upper Handlebar Assembly -[] 4
[] 2 Front Wheels -[] 3
[] 2 Rear Wheels -[] 4
[1] 1 Collection Bag -[] 2
[] 1 Operators Manual -[] ©
[] 1 Limited Warranty Statement -[] 1
[] 1 Warranty Registration Card -[] 1
[] 1 Safety Goggles -[] 1
[] 1 Engine Manufacturer's Operators Manual -[] 2
[] 1 Transmission Warranty Statement -[] 0
-[] 0
-[] 0
-[] 0
-[] 1
check for missing parts.
and
A
;
CSV-5S
CSV-8S
5/16"-18 x 1 3/4" Hex Hd Bolt NC
5/16" ID Flat Washers
5/16"-18 Nylock Nuts NC
5/16"-18 x 3/4" Hex Hd Bolt NC
5/8" ID Flat Washers
5/8" -11 x 4 -1/2" Hex Hd Bolts NC
1/4" Clevis Pins w/ Spring Pins
8 - 32 x 13/4" Rd Hd Machine Screw
8 - 32 Locknut
6 - 32 Locknut
1/8 x 1-1/4" Cotter Pin
1/4" Flat Washer
1/4 - 28 X 3/4" Cap Screw
Double D Washer
10 - 24 x 3/8" Button Socket Hd
Capscrew
#6 Flatwasher
ON = = = © == == = DN) ON) OB WON WOON
—
10/lECHD
19
20
10.
11.
12.
13.
14.
15.
16.
17.
18.
CHIPPER/SHREDDER/VACUUM 11
OPERATOR'S MANUAL
OPERATORS MANUALS - There are two Operators Manuals included, one for the Chipper/Shredder/Vacuum and
one for the engine. Read both before operation and keep in a safe place for future reference.
BASE UNIT ASSEMBLY - Factory assembled unit to which wheels, handle, shredding hopper, discharge elbow and
collection bag are installed.
SHREDDING HOPPER - Mounts to the front of the shredding housing and swivels providing three operating positions.
Contains a safety baffle that must be in place at all times.
A. Upright, for manual feeding of material. Stationary Operation.
B. Vertical, for raking leaves directly next to hopper allowing vacuum action to draw material in for shredding.
Stationary Operation only. |
C. Down, for Walk Behind vacuuming of leaves. Mobile Operation.
CHIPPING CHUTE - Directs material to be chipped against the back of the Rotor Assembly where the Chipper Knives
are located. Contains a safety baffle that MUST be in place at all times.
HOPPER LATCH - Spring loaded mechanism that engages notches in flange of Shredding Hopper. Holds Hopper in
either the Upright or Down position. Pull latch out and turn hopper to desired position. Release latch. Check that latch
engages notch.
DISCHARGE ELBOW - Directs shredded/chipped material into Collection Bag or through Optional “Discharge Chute
Extension” (19).
COLLECTION BAG - Mounts to the discharge elbow and “J” bolt hook on handle. A large panel of open mesh allows
air to pass through the bag while retaining the shredded material.
SHIFT LEVER - Self propelled models only. Shifts transmission from Neutral, Reverse and three Forward speeds.
BAIL - Self propelled models only. Lifting up on the bail tightens the drive belt propelling the unit.
REAR WHEELS - Serve as drive wheels on self propelled models.
FRONT WHEELS - Free wheeling on all models. Grease fittings contained inside both wheels.
BAR GRATE - A heavy duty weldment located in the outlet of the shredding chamber through which all shredded and
chipped material must pass. The grate can be removed for cleaning and is held in place with two heavy duty clevis pins
which are retained by spring pins.
HAMMERS - (Not Illustrated) There are three sets of heavy, flail type hammers mounted on the Rotor. As the Rotor
turns, centrifugal force causes the hammers to extend away from the rotor shredding the material in the chamber. The
Hammers do not require sharpening and are replaceable when worn.
CHIPPER KNIFE - (Not Illustrated) Two Knives mounted to the back of the Rotor chip material fed through the
Chipper Chute. The knives can be re-sharpened and are replaceable.
TRANSMISSION - Receives power from the engine via a belt and transmits power to the differential/rear axle with a
roller chain. There are three (3) forward speeds, one (1) reverse speed and a neutral position.
DIFFERENTIAL - Located on the rear axle. Applies power to both rear wheels equally when traveling in a straight
line. Allows wheel on the inside of a turn to turn slower for easy turning.
HEIGHT ADJUSTMENT THUMB LEVER - Located on the right side of the handle bar. Depressing the lever
releases the Height Adjustment Index Plate (18) located on each side of the lower frame just behind the front wheels.
Pushing down or lifting up on the handle bar raises or lowers the front of the unit.
HEIGHT ADJUSTMENT INDEX PLATE - Notched plate that is held engaged with the height adjustment tab on the
side of the frame by a spring. Depressing the Height Adjustment Thumb Lever releases the Index Plate allowing up or
down height adjustment.
12MUECHO
19. DISCHARGE CHUTE EXTENSION (OPTIONAL) - MUST be used when the Collection Bag is not used. For
BLOWER use or when shredded/chipped material is to be broadcast during mobile operation or directed into a con-
fined collection area during stationary operation.
20. DEFLECTOR PLATE - Directs flow of air during blowing.
N
N
/ ASSEMBLY
IMPORTANT The engine is shipped from the factory WITHOUT OIL! Oil must be
added to the engine before starting. Engine service is the last step prior to initial start-up.
Tools Required: 3/8", 1/2" and 15/16" open end wrenches.
Install Front Wheels —
Parts Required: Two (2) wheel assemblies with short hubs, two (2) 5/8" -
11 x 4 1/2" Hex Hd Bolts, and four (4) 5/8" ID Flat Washers. Tire pressure
should be checked prior to wheel, tire assembly installation. Tire pressure
for all models is 30 psi.
1. Place one sheet of the cardboard packing material in front of the unit
and tip the unit forward on the cardboard .
2. Place one flat washer on each bolt. Install bolt from the side of the
wheel with the air stem (the grease fitting goes to the inside). Place an
additional washer on bolt and thread into the height adjuster cradle.
Do not over tighten, bolt wheel should turn freely.
Install Rear Wheels —
Parts Required: Two (2) wheel assemblies with long hub, two (2) clevis
pins and two (2) spring pins, Self Propelled Unit. Walk behind also
requires an axle and uses two (2) 1/8 x 1 1/4" Cotter Pins in place of the
Clevis pins.
1. (Walk Behind Only) - Slide axle through the holes in the rear of the
engine tray.
2. Slide wheels on axle and align hole in axle with hole in wheel hub.
3. Insert clevis pin and secure with spring pin on CSV-5S and CSV-8S
model or cotterpins on the CSV-5 model.
4. Pivot unit back on its’ wheels.
CHIPPER/SHREDDER/VACUUM
Install Wheel Guard Kit — (CSV-5S, CSV-8S)
Parts in Kit include: Guard, Two (2) 3/8-16x3/4 self tapping bolts.
To install wheel guard kit, place the guard over the right rear tire, as seen
from operator's position. Align the guard (A) mounting holes with the
holes (B) provided in the right hand side plate. Secure the guard with the
two (2) 3/8-16x3/4 self tapping bolts (C) included in the kit.
Install Upper Handle Bar — Self Propelled Unit
Parts Required: Handle Bar Assembly, Shift Lever Guide, six (6) 5/16" x
1 3/4" Hex Hd Bolts, six (6) 5/16" Lock Nuts, two (2) 8 - 32 x 1 3/4" Rd
Hd Machine Screws, two (2) 8 - 32 Locknuts.
1. Use the lower or upper set of holes in the lower handlebar depending
on operator height and comfort. If the lower set of holes is used, only
four (4) of the six (6) hex head bolts and nuts will be used.
2. Install the Shift Lever Guide (A) in the bottom holes.
OPERATOR'S MANUAL
13
NOTE The CSV-8S is supplied with four (4) 5/16" x 1-3/4
Hex Hd bolts and two (2) 5/16" X 1-1/2 Hex Hd Bolts. When
installing the handle bar onto the upper set of holes in lower handle
bar use the two (2) 1-1/2" length bolts in the top left and top right
holes to assure clearance between the bolt and fuel tank.
Install Height Adjuster Trigger
3. Uncoil the Height Adjuster Cable, use care not to twist cable.
4. Attach the trigger assembly to the top of the right handle. Mount
trigger with preassembled 6-32 x 2 RD HD Machine Screw (B).
Assemble #6 flatwasher and 6-32 locknut and tighten.
5. Check height adjuster cable operation. Depress height adjuster trigger
(A) and push down on rear handle bar. The cable should pull the
height adjustment index plate (B) clear of the frame tab (C) allowing
the unit to pivot to the alternate height notches in the index plate (B).
When the height adjustor trigger (A) is released the index plate notch
should fully engage the frame tab (C). If index plate (B) does not
release from the frame tab or engage the frame tab (C), adjust the
cable as follows:
14/ECHD
- Loosen cable clamp screw (D) using a 5/32" allen wrench. Widen
clamp with screw driver to allow free cable movement.
- To adjust for more engagement move cable (E) forward as required to
allow index plate (B) to fully engage frame tab (C).
- To adjust for disengagement move cable (E) backward as required to
allow index plate (B) to disengage frame tab (C).
- Tighten clamp screw (D).
NOTE It may be necessary to disconnect the spring at the other
end of the height adjustment cable to gain enough slack to reattach the
inner wire.
Install Traction Drive Cable
6. Uncoil the Traction Drive Cable, use care not to twist cable.
7. Connect "Z" End (D) to hole in bail.
8. Attach mounting bracket to the handle bar using one 8 - 32 x 1 3/4"
Rd Hd Machine Screw (B) and one 8 - 32 Locknut (C).
9. Install the "Z" end of the idler pulley engagement cable (D) to the
center hole of the clutch lever (E).
10. Install the return spring (H) located at the end of the traction drive
cable to the idler pulley engagement cable (D).
11. The threaded cable end will have two (2) lockwashers and two (2)
nuts. Thread the inner nut to the halfway position on the threads.
Unscrew the outer nut with one lockwasher completely off the
threads. Insert the end of the threaded cable sleeve into the lower
cable mounting bracket. Reinstall the outer lockwasher and nut.
\
NOTE A lock washer and nut (A&B) should be on each side of
the lower mounting bracket as shown.
12. Secure the two nuts against the mounting bracket using two 1/2
inch open end wrenches. After unit is completely assembled,
check belt tension as outlined in maintenance section under
“Checking Belt Tension - Level 1”. If belt adjustment is necessary
follow “Adjusting Belt Tension - Level 2” in maintenance section of
operator’s manual.
NOTE If no adjustment on cable end remains, remove "Z" end of
pulley engagement cable (C) from clutch lever (E). Move cable end
"Z" to forward hole (F) for increased tension or rear hole (G) to
decrease tension.
CHIPPER/SHREDDER/VACUUM 1 5
OPERATOR'S MANUAL
Install Upper Handle Bar - Walk Behind Unit
Parts Required: Handle Bar Assembly, four (4) 5/16" x 1 3/4" Hex Hd
Bolts, four (4) 5/16/" locknuts.
1. Use the lower or upper set of holes in the lower handlebar depending
on operator height and comfort.
ns ] À r lrigoer
2. Uncoil the Height Adjuster Cable, use care not to twist cable.
3. Remove the Inner Wire (A) from the trigger to gain access to the
mounting hole. Attach the trigger assembly to the top of the right
handle using one 8 - 32 x 1 3/4" Rd Hd Machine Screw (B) and
one 8 - 32 Locknut (C).
4. Reattach the inner wire and test.
NOTE It may be necessary to disconnect the spring at the other
end of the height adjustment cable to gain enough slack to reattach
the inner wire.
Transmission Lever and Cover - Self Propelled Only
Parts Required: Shift lever, Transmission Cover, one (1) double "D"
Washer, one (1) 1/4" Flat Washer, one (1) 1/4-28 x 3/4" Hex Hd
Capscrew, six (6) 10-24 x 3/8" Button Hd Hex Socket Capscrews.
1. Install Double D Washer (A) on transmission shift shaft. Place
Transmission Cover (B) over transmission with slot to rear, DO NOT
FASTEN. ’
2. With the Handle (C) to the rear, slide the Shift Lever (D) through the
Shift Lever Guide (E) and the slot in the Transmission Cover (B).
3. Place the Shift Lever (D) on the transmission shaft, use the 1/4" Flat
Washer (F) and 1/4-28 x 3/4" Capscrews (6) to secure the shift lever.
4. Lower the Transmission cover (B) over the transmission and secure
with the six (6) Button Hd Hex Socket Capscrews (H).
16 ECHO
1.
1.
Г Install Shredding Hopper —
Parts Required: Shredding Hopper.
Installing Shredding Hopper (C) reposition Hopper Latch (B) to Base
Unit Assembly (D).
Position Hopper Latch (B) over bolt (E).
Use one (1) 5/16-18 Nylock Nut (H) and tighten fully clockwise, then
turn 5/16-18 Nylock Nut (H) one (1) full turn counter- clockwise.
Hook Return Spring (F) to Bolt (G).
Remove the three (3) Hopper Clamps (A) and place the Hopper over
the front plate collar. Align one of the cutout notches in the flange of
the hopper with the locking bracket (B).
Reinstall the three Hopper Clamps. DO NOT over tighten. Hopper
must be free to swivel. Disengage Lock Bracket (B) and swivel
Hopper entire 360 degrees. Adjust clamp tightness as necessary.
Install Discharge Elbow & Collection Bag —
Parts Required: Discharge Elbow, three (3) 5/16" x 3/4" Hex Hd Bolts,
three (3) 5/16" Flat Washer, Collection Bag.
Place Elbow on housing opening with opening pointing to the rear of
the machine. Secure with three (3) bolts and washers.
4A DANGER
Never operate unit without collection bag installed unless optional discharge chute extension is installed. Extra care
must be taken to direct the discharge away from all people and animals. Serious personal injury from flying
materials is possible.
Place the open end of the collection bag over the elbow opening,
Tighten the strap securing the bag to the elbow.
Hang the loop found at the rear of the bag on the “J” bolt located on
the handle bar.
Prepare Engine for Operation —
IMPORTANT Engine is shipped without oil. Follow instruc-
tions found in Engine Manufacture's Operators Manual for Start-up
instructions.
Below sterling win mine,
read and under Mark this Covner's Manual
qu
Owner's Manual
Model Series 133200 4 135200
al
Ap AR Al A TE | bd ELA A E E |
a de O | Ma оеетоноуровтож тя жн жал вгынинитвланин жовтья e
CHIPPER/SHREDDER/VACUUM 17
OPERATOR'S MIANUAL
7 N
PRE-OPERATION
Fuel and Lubricant Requirements — 4 Stroke Engine
(OP m | 0
Owner's Manual
Model Series 133200 & 135200
Engine, Gasoline and Lubricating Oil - Refer to Engine Manufacturers
Operators Manual for Oil and Fuel recommendations.
Transmission Oil -- Transmission is lubricated for the life of the product
and does not require checking or addition of oil.
Storage- Fuel storage laws vary by locality. Contact your local government
for the laws affecting your area. As a precaution, store fuel in an approved,
. . “ . . . . . Mod e
air tight container. Store in a well ventilated, unoccupied building, away da —— [IDE
from sparks and flames. ne rare ol Baby corer ARE rare race ‘
ET к.кокаооукоосооназанн нано evieoneraneraon an iapeer er aa Ё
Staring ной Ворд СНЯТЬ
IMPORTANT Stored fuel ages. Do not buy more fuel than om teen cero EE
you expect to use in thirty (30) days.
N
( OPERATION - ALL MopeLs N
A WARNING [85 na nd manu] iy
Do not attempt adjusting, modifying or repairing the Engine Gover-
nor System. Serious personal injury or unit damage may result. If a
problem exists contact your Authorized ECHO Servicing Dealer for
Model Series 133200 & 135200
repairs.
NOTE Instructions for safe engine operation are found in the ete ee ts ООО
Engine Manufacturer's Operators Manual packed separately. a :
Gaara rm se nes ce se uaute casa ea ea ana pos 3 Barvios & Slorage .- ,
NOTE Inthe event the unit is clogged or jammed, stop engine
and allow time for all moving parts to come to rest. Disconnect spark
plug and move it away from the plug. Allow muffler and engine to
cool before removing clogged materials.
There are two basic modes of operation possible with your Chipper/Shred-
der/Vacuum/Blower. The first is stationary where the material to be pro-
cessed is brought to the machine. The second is mobile where the machine is
pushed or self- propelled over the area to be vacuumed or blown clear.
18/MECHO
Stationary Shredding/Chipping —
A WARNING
Stationary operation is possible with and without the Collection
Bag. If operated without the bag, the Optional Discharge Chute
Extension must be installed or serious injury from flying debris
can occur.
A WARNING
When operating with the Optional Discharge Chute Extension, use
extreme care not to direct the air flow toward others in the area. The <A
fifty (50) foot (15m) safety zone must be strictly enforced or serious an OPTIONAL
personal injury can occur. DISCHARGE CHUTE
EXTENSION
1. Push the unit to a solid, level work area using the handlebar. Block
the wheels to prevent movement.
2. Position the unit for ease of access to the material to be Shredded or
Chipped.
3. Install the Collection Bag or Optional Discharge Chute Extension.
4. Shift the unit into Neutral (self propelled model) and start the engine.
Set the throttle at Wide Open Throttle (WOT).
A WARNING
DO NOT put any material in the shredding hopper larger than 1/2"
in diameter. Serious personal injury can occur from flying material.
5. Material consisting mostly of leaves can be raked next to the hopper
With the hopper turned to the side (perpendicular) and the leaves will
be drawn into the machine and shredded.
CHIPPER/SHREDDER/VACUUM 1 9
OPERATOR'S MANUAL
6. Material containing small branches, up to 1/2" (13mm) in diameter, is
placed on top of the hopper opening. The machine will self feed. DO
NOT feed material faster than the machine can handle.
A DANGER
DO NOT place hand beyond line on safety decals. Serious
personal injury can occur.
7. Material over 1/2" (13mm) but less than 3" (75mm) can be fed
through the Chipper Chute. Feed branches slowly and carefully large
end first. NEVER force a branch in the chipper chute.
8. When the collection bag is full, STOP the engine and allow it to come
to a complete stop before removing the bag.
A CAUTION
Under normal shut down circumstances (engine shut down and
stopped), the Shredding/Chipping Rotor will continue to turn for
approximately twenty (20) seconds. Not waiting for unit to come
to a complete stop can result in serious injury.
Mobile Vacuuming Leaves —
ÁNWARNING
Mobile operation is possible with and without the Collection Bag.
If operated without the bag, the Optional Discharge Chute Exten-
sion must be installed.
1. Check the hopper to ground clearance. Adjust the hopper height as
required.
2. Install the Collection Bag or Optional Discharge Chute Extension.
A WARNING
Operation with the Optional Discharge Chute Extension requires extreme care. Do not direct
the air flow toward others in the area. The 50 foot (15 m) safety zone must be strictly
enforced or serious personal injury can occur.
20MNMECNO
3. Shift the unit into Neutral (self propelled model) and start the engine.
Set throttle control at Wide Open Throttle (WOT).
4. Shift into gear and pull up on bail engaging the drive (self propelled
model) or push the unit over the area needing vacuuming. Adjust
forward speed to match the difficulty of vacuuming. Move slower
when the volume of leaves is large. To change gears, Release Bail,
come to a Complete Stop then move the Gear Lever to the desired
setting.
5. When collecting the shredded leaves in the Bag, try to plan your path
so you will frequently pass the point you will be depositing the
shredded leaves.
6. When the Collection Bag is full, Stop the engine and allow it to come
to a complete stop prior to removing the bag.
А CAUTION
Under normal shut down circumstances (engine shut down and
stopped), the Shedding/Chipping Rotor will continue to turn for
approximately twenty (20) seconds. Not waiting for unit to come
to a complete stop can result in serious injury.
Operation as a Blower - Optional Accessory
A WARNING
Operation as a blower requires the installation of the Optional Discharge Chute Extension. Use
extreme care not to direct the air flow toward others working in the area. The fifty (50) foot
(15m) safety zone must be strictly enforced or serious personal injury can occur.
1. Mount Optional Discharge Chute Extension. Refer to Installation
Instructions in Blower Package.
2. Place the Shredder Hopper in the up position.
3. Shift the unit into Neutral (self propelled model) and start the engine.
Set throttle control at Wide Open Throttle (WOT).
4. Shift into gear and pull up on bail engaging the drive (self propelled
model) or push the unit over the area to be blown clear. Adjust
forward speed to match the difficulty of blowing. Move slower when
the volume of leaves is large. To change gears, Release Bail, come to
a complete stop, then move the Gear Lever to the desired setting.
>. Try to plan your path so you will direct the leaves to one area for
easier cleanup.
CHIPPER/SHREDDER/VACUUM
OPERATOR'S MANUAL 2 1
Level 1:
Level 3:
MAINTENANCE
Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your
product achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an
authorized ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT- YOURSELF or have an
ECHO Dealer do it, each maintenance task has been graded.
Level 2: Moderate difficulty. Some specialized tools may be required.
by an authorized Echo Service Dealer.
Easy to do. Most required tools are common to average household.
Experience and skill required. Specialized tools are required. Echo recommends this level of service be performed
~
4) DANGER
Before performing any maintenance or repair, STOP engine and
allow time for all moving parts to come to complete rest. Discon-
nect spark plug wire and move it away from the plug. Allow
muffler and engine to cool before beginning maintenance. Failure
to follow these instructions may result in serious personal injury.
Cleaning — Level |
Tools Required: Stiff Bristle Brush, Drying Rag, Garden hose and normal
water pressure.
Parts Required: As Needed.
NOTE To ensure long life and consistent performance, cleaning
after each use is recommended.
Brush accumulated dirt and debris from all surfaces.
Remove the Collection Bag and empty completely. If bag is damp/wet
from processing green or wet material hang to dry. NEVER store bag
wet.
Remove loose material from Discharge Elbow. Check Bar Grate for
evidence of material that has dried to the grate bars. If necessary, the
Bar Grate can be removed for cleaning by removing the Discharge
Elbow, Spring Pins and Clevis Pins. Grate can now be lifted from the
Shredder Housing outlet.
4A DANGER
Do not operate unit without Bar Grate in position. Serious personal
injury can occur from flying material.
22MECHO
4. Protect the engine from direct water spray and clean the rest of the
and out. Allow the water to soften the dirt then rinse clean with the | | |
hose.
5. Engine cleaning is covered in the Engine Manufacturers Operators
Manual 4.
6. When assembling the grate into the blower housing, the grate should |
be aligned with the raised edges out towards discharged outlet as
shown in (A). The extended ends of the grate as shown in (B) must be
installed against the front wall of the Blower Housing (Hopper Side).
When grate is properly installed clearance between the two grate
flanges on the left will be 1" apart, with 3/4" clearance between the
remaining grate flanges.
NOTE Improper grate installation may cause shredder hammer
failure.
NOTE If Poor Vacuuming and Shredding Action is Experienced,
additional cleaning of the interior may be needed.
unit with water. Best results are experienced by wetting the unit inside EOS
BLOWER
HOUSING
FRONT
WALL,
HOPPER
SIDE
Cleaning Unprocessed Material From Shredding Chamber —
7. Remove five (5) Nylok locknuts securing the Front Cover to the
Shredder Housing and lift Front Cover from the unit.
8. Clean all unprocessed material from inside the Shredder Housing and
from the Rotor. Rinse clean with water.
9. Install the Front Cover and tighten the Locknuts.
NOTE The nut retaining the Hopper Latch is not tightened but
left loose enough to allow free movement of the Latch.
10. Wipe water from the unit and place in direct sunlight (if possible) to
thoroughly dry. Run unit for five (5) minutes to dry inside
components.
Lubrication —
AA DANGER
Before performing any maintenance or repair, STOP engine and allow time for all moving parts to
come to complete rest. Disconnect spark plug wire and move it away from the plug. Allow
muffler and engine to cool before beginning maintenance. Failure to follow these
instructions may result in serious personal injury.
Regular Lubrication is important to the long life of your Chipper/Shredder. Always use the lubricant
recommended. Use of product other than that specified may affect your Warranty.
CHIPPER/SHREDDER/VACUUM
OPERATOR'S MANUAL
23
Wheel Bearings — Level 1
Tools Required: Grease Gun, Clean Shop Cloth.
Parts Required: Lithium Based Chassis Grease
NOTE Only the front wheel bearings require lubrication. The
rear wheel bearings are sealed.
Clean the grease fitting and pump grease in the bearing until the
grease just begins to squeeze from the wheel. Remove excess grease.
Drive Chain & Jack Shaft — Level 2
Tools Required. Cleaning Brush. 1" or 2" medium bristle paint brush, oil can,
Grease Gun.
Parts Required: Kerosene or another oil based solvent, 20W engine oil,
Lithium based chassis grease.
1.
2.
Ir
Remove bottom cover,
Clean drive chain with kerosene and a brush. Apply a generous
coating to the chain and allow kerosene to soak in, approximately ten
(10) minutes. Rinse with clean kerosene and dry.
Coat chain with clean 20W oil and allow oil to soak in. Wipe excess
oil from chain.
Clean grease fittings on each jack shaft support bearing and fill each
bearing with grease. Wipe excess grease from bearings.
Mission —
A
Transmission is lubricated for the life of the product. No provisions are made for checking or adding lubricant.
Replacing/Sharpening Chipper Blades
Replacing Hammers —Level 3 (Echo recommends this level of service be performed
by an authorized Echo Service Dealer.)
Tools Required: 1/2" open end wrench, 9/16" Socket Wrench with extension, 15/16" open end wrench, *Loctite, Blue, No. 262.
(* Loctite is a registered Trademark), 5/8"-11 x 4-1/2" Hex Hd Bolt, 2" x 2" x 2' length of wood or “C-Clamp”.
Parts Required: Chipper Knives, Hammers.
A DANGER
Before performing any maintenance or repair, STOP engine and allow time for all moving parts to come to complete
rest. Disconnect spark plug wire and move it away from the plug. Allow muffler and engine to cool before beginning
maintenance. Failure to follow these instructions may result in serious personal injury.
24 {ECHO
IMPORTANT This maintenance procedure requires use of Loctite
Unit must not be used for 24 hours after reassembly to
allow time for proper curing.
Remove Rotor —
1. Remove five (5) locknuts securing the Front Cover to the Shredding
Housing and lift Front Cover from the unit.
2. Remove the Bolt located at the center of the Rotor. Hold Rotor in
place with a 2" x 2" x 2' length of wood or a “C”- Clamp.
NOTE If "C-Clamp" is used, protect finish with cardboard.
3. Lubricate threads of 5/8" - 11 X 4-1/2 Hex Hd Bolt and thread in the
end of the rotor until bolt touches crankshaft. Tighten the bolt
against the crankshaft end, then tap sharply with a hammer. The rotor
will loosen slightly. Retighten the bolt and repeatprocedure until the
rotor is completely loose.
4. Check that all Hammers are swung “IN” and will clear the opening in
the Shredder Housing. Continue to turn the Bolt until the Rotor can be
lifted from the unit.
5. Inspect Rotor, Chipper Knives and Hammers. Sharpen or replace as
needed. Knives and/or Hammers should be replaced as a set to assure
proper balance. Inspect Square Rotor Key. Replace if evidence of
shearing is noted.
6. Clean engine shaft and place the Square Rotor Key in the keyway.
7. Wipe the bore of the Rotor with a clean rag. Note the position of the
keyway, align it with the Key in the engine shaft and push the Rotor
on the shaft. Rotor is correctly installed when the front of the Rotor is
5/8" to 3/4" (16-19 mm) below the front of the Shredder Housing.
8. Clean the threads of the Rotor retaining bolt. Coat threads with Loctite
and tighten to 50 ft. Ibs. Do not run unit for 24 hours.
9. Rotate Rotor several revolutions to assure it has been installed
correctly and does not contact any part of the machine. Check that it
rotates evenly and does not wobble.
10. Install the Front Cover and tighten the Locknuts. The one nut retaining 18-314"
the Hopper Latch is not tightened but left loose to allow free (16-19 mm)
movement of the Latch.
CHIPPER/SHREDDER/VACUUM 25
OPERATOR'S MIANUAL
+
Remove Chipper Knives — Level 3 (Echo recommends this level of service be performed
by an authorized Echo Service Dealer.)
Tools Required: 1/2" open End Wrench, Hexagon Wrench, Loctite, Blue, No. 262.
Parts Required: Chipper Knives
WARNING 4h DANGER
Chipper knives are VERY sharp. Use extreme care removing and installing knives or serious personal injury will occur.
IMPORTANT This maintenance procedure requires use of
Loctite. Unit must not be used for 24 hours after reassembly to
allow time for proper curing.
1. Remove the three (3) Socket Head Capscrews and nuts that secure
each knife.
2. Inspect knives for cracks, missing pieces and flatness. If replacement
is required, replace knives as a pair to assure proper balance.
3. Ifknives are to be re-sharpened, use great care not to overheat knife
(turn edge glowing red while grinding and blue/black as it cools).
Grind edge to maintain the original 45 degree angle. Cool knife with
water during grinding. If you are not familiar with grinding, take the
knives to your ECHO dealer for sharpening. Г — уч
4. Carefully clean knife mounting surface and install knives with a5" D THIS
Capscrews and Nuts using Loctite. Follow Loctite instructions \ 7 IDE
included with the product.
Replace Hammers — Level 3 (Echo recommends this level
of service be performed by an authorized Echo Service
Dealer.)
Tools Required: 1/2" Open End Wrench, 1/2" Socket Wrench with
Extension, Loctite, Blue, No. 262.
Parts Required: Hammers and other parts as required.
IMPORTANT This maintenance procedure requires use of
Loctite. Unit must not be used for 24 hours after reassembly to
allow time for proper curing.
26 [ECHO
1. Remove the Bolt and Nut retaining the Rotor Pin, slide the Pin from
the Rotor along with the hammers, spacers and washers.
2. Inspect and replace worn and damaged parts. Clean bolt threads.
3. Reassemble following illustration. Use Loctite on the Rotor Pin
retaining Bolt. Follow Loctite instructions included with the product.
Drive Belt Replacement — Level 3 (Echo recommends this level of service be performed
by an authorized Echo Service Dealer.)
Tools Required: 7/16" Open End Wrench, Hex Wrench, 3/8" Open End Wrench.
Parts Required: Engine to Jackshaft Drive Belt, Jackshaft to Transmission Drive Belt.
AA DANGER
Before performing any maintenance or repair, STOP engine and allow time for all moving parts to come to complete
rest. Disconnect spark plug wire and move it away from the plug. Allow muffler and engine to cool before beginning
maintenance. Failure to follow these instructions may result in serious personal injury.
1. Remove Belt Guard, Shredding Hopper and Bottom Cover. Stand unit
on it's front and block securely.
2. Remove four (4) Socket Head Capscrews, Spacers and Washers and f= —]——— |
remove Starter Assembly. O
z D
3. Remove Idler Return Spring (A). à —
: B
4. Loosen set screws in bearings (B) and pulleys (C). Slide jackshaft (D) E Y
from bearings. defi
я
5. Remove old belts and install new belts. — С
6. Slide jackshaft through the rear bearing, driven pulley, transmission | i FER
drive pulley and front bearing. Position bearing setscrews over milled A
flats on Jackshaft and tighten.
7. Replace Idler Return Spring. = B
8. Align Pulleys on Jackshaft with engine and transmission pulleys and
tighten setscrews.
IMPORTANT Correct belt alignment increases belt life and
performance.
9. Install Starter and Belt Guard.
10. Install bottom Cover, return unit to its wheels and install Shredding
Hopper.
Fabre «
CHIPPER/SHREDDER/VACUUM
OPERATOR's MANUAL
Traction Drive —
Traction Drive testing and adjustment is needed whenever a new belt is
installed and periodically during the life of the product. To see if your
Traction Drive needs adjusting perform the following checks:
Checking Belt Tension — Level 1
1. Park your unit on a level, dry, concrete/asphalt surface. Block the
front wheels to prevent forward movement. Do not use the Hopper
as a bumper or damage to the Hopper will occur.
27
NOTE The tires may spin during this test leaving Black marks
on the pavement. Select the test site with this in mind.
2. Start engine and place throttle in WOT (Wide Open Throttle) position.
Shift transmission to First (1) gear. Do not pull up on Bail to engage
drive. Observe unit. If the drive wheels try to move and you can see
the belt is not slipping freely on the engine drive pulley, the belt
tension needs to be relaxed.
3. With engine still running WOT, shift transmission to Third (3) gear.
Check that unit is firmly blocked in place and pull up on bail to
engage Drive Belt. One or both Rear wheels should turn. If neither
wheel turns, belt tension needs to be increased.
Adjusting Belt Tension — Level 2
Tools Required: Two (2) 1/2" Open End Wrench.
Parts Required: As needed.
—
A DANGER
Before performing any maintenance or repair, STOP engine and allow time for all moving parts to come to complete
rest. Disconnect spark plug wire and move it away from the plug. Allow muffler and engine to cool before beginning
maintenance. Failure to follow these instructions may result in serious personal injury.
To tighten belt:
1. Loosen Nut (A) 2 to 3 full turns.
2. Tighten Nut (B).
3. Retest by following Step 3, “Checking Belt Tension”. Repeat Testing
and Adjusting until proper belt tension is reached.
4. If proper Belt Tension cannot be achieved through this adjustment, the
belt should be replaced.
ПЕСН
To loosen belt:
5. Loosen Nut (B) 2 to 3 full turns.
6. Tighten Nut (A).
7. Retest by following Step 2, “Checking Belt Tension”. Repeat Testing
and Adjusting until proper belt tension is reached.
Storage - Long Term
If the Chipper/Shredder will not be used more than 30 days, the following
Service & Storage
Storage procedure must be performed.
STORAGE INSTRUCTIONS
Engines stored over 30 days need to bs protected or drained of fuel
to prevent gum from forming in fuel sytem or on esential caburetor
NOTE Always allow the unit to cool before storing. parts.
1. Forengine protection, we recommend use
of Briggs & Stratton Gasoline Additive.
Part No 5041, available from any Autho-
rized Briggs & Stratton SErvice Dealer.
Mix Additive with fuel in fuel tank or storage
container. Run engine for a short time ot
circulate Additibe through carburetor.
Engine and fuel can be sored up to 24
months.
1. Clean Unit. Follow instructions in this section.
2. Prepare engine for storage. Refer to Storage Information in the Engine
Operators Manual.
NOTE: If additive is not used or if engine is operating on gasoline
: : : 4 : : containing alcohol, such as gasohol, remove all fuel from tank and
3. Perform Lubrication specified in this section. run engine until t stops frony alek of fuel.
. . . 2. While engine is stilt warm, drain oil from cankcase (see page
4. Perform Pre-oper ation inspection. 6). Ref with fresh oil of recommended grade (see chart on
age 2).
3. emove spark plug and pour about 1/2 oz. (15 m) of engine
5. Use touch-up paint to cover any scratches or nicks in the paint before te cer. Replace spark plug and crank slowly to
rust begins. Wipe all surfaces with a cloth saturated with light oil, 4. clean dirt and chaff from cylinder, cylinder head fins, blower
v4. . housing, roating screen and muffler areas (see page? ).
silicone spray or other protective products. 5. Store in a clean and dry area, but NOT near a stove, furnace
or water heater which uses a pilot light or any device that can
create a spark.
6. Store Chipper/Shredder in a clean, dry, well ventilated area but NOT
near a stove, furnace or water heater which uses a pilot light or any
device that can create a spark.
7. Store the unit out of the reach of children.
CHIPPER/SHREDDER/VACUUM 29
OPERATOR'S MANUAL
SERVICING INFORMATION
Echo System2 1m
Parts — Chipper/Shredder/ Vacuum
Genuine ECHO Parts and ECHO RE POWER Parts / Assemblies for your Serial Number: 05 060 1050
ECHO product are available only from an Authorized, ECHO Dealer.
When you do need to buy parts ALWAYS have the Model Number and
Serial Number of the unit with you. You can find the model number on top
of the unit and the serial number on the decal attached to the underside of
the Transmission Cover (Self Propelled Models) or the Engine Tray just
below the handles (Walk Behind Model). For future reference, write (Sam ple Decal)
them in the space provided below.
Echo Incorporated
Richmond, Virginia 23223
US Patent 4 5,340,035
MODEL NO. SN. DEALER?
Service—
Service of this product during the warranty period must be performed by Call
an Authorized ECHO Service Dealer. For the name of the Authorized
ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432
ECHO (3246). When presenting your unit for Warranty service/repairs, 1-800-432-ECHO (3246)
proof of purchase is required.
MUERO ATA wed WARRANTY REGISTRATION Ci
{Copy of Limited Warrant
(En el Manual Dal Cparador sa inch
W ty Card. POR RAVOR, ESCRIBA CON LETRA DE MPRE
arran ard— = En NADO BUT TN SRS
This card is our means of registering all original owners of ECHO =
equipment and the card plus proof of purchase provides you the assurance o [rome reese
that authorized warranty work will be done. It also provides a direct link “в о РН СЕ 30 Сл! ¿NDA?
between you and ECHO if we find it necessary to contact you. cue ADN mer Comm Born”
Ds.
[ar ecouconco POSTAL
L ! MO. TYPE NO. | PATERUROHASES-
NUMERO DEL MODEL NUMERO DE $EME VAS NUMERO DE "PO FCCHA DE COMPRA J
eee er PFA er tbe de er
ONECHD
SPECIFICATIONS
Vacuum Width
22"
Chipper (max. branch diameter)
3"
3"
Hopper Height Adjustment Range
5/8" - 12-1/2"
5/8" - 12-1/2"
5/8" - 12-1/2"
Engine (Briggs & Stratton) 5 H.P. 5 H.P. 8 H.P.
Fuel Capacity 1 gallon 1 gallon 1.2 gallon
Bag Capacity 2.8 BU. 2.8 BU. 2.8 BU.
Discharge Chute Extension Optional Optional Optional
Vacuum Hose Optional Optional Optional
Hose Length 10" 10" 10"
Hose Diameter
4"
| MPH,
First N/A 0.91 0.91
Second N/A 1.19 1.19
Third N/A 2.8 2.8
Reverse N/A 1.38 1.38
Differential No Yes Yes
N/A Yes
Tire Size
10" x 4"
Tire Air Pressure
CHIPPER/SHREDDER/VACUUM 31
OPERATOR'S MANUAL
( >
DecaLs, WARNING/INFORMATIONAL
Locate these safety decals on your unit. The complete unit illustration found in the “DESCRIPTION” section, will help you
locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot
be read, a new one can be ordered from your ECHO dealer.
Á CAUTION /
READ AND UNDERSTAND THE OPERATOR'S MANUAL BEFORE
USING THIS CHIPPER/SHREDDER.
- KEEP BYSTANDERS, CHILDREN AND PETS AT LEAST 50 FT. (15M)
AWAY FROM OPERATING AREA.
- KEEP ALL SHIELDS AND GUARDS SECURELY IN PLACE.
DO NOT INSTALL, REMOVE OR ADJUST ANY PART ON UNIT
WHILE ENGINE IS RUNNING,
- BE SURE ALL FASTENERS AND COMPONENTS ARE SECURELY
IN PLACE.
DO NOT RUN ENGINE IN ENCLOSED AREA. EXHAUST
GASES CONTAIN POISONOUS CARBON MONOXIDE.
- TO AVOID A FIRE, KEEP LEAVES, GRASS AND OTHER
COMBUSTIBLE MATERIALS AWAY FROM HOT ENGINE
AND MUFFLER.
- NEVER USE HANDS OR FEET TO CLEAR JAMS, USE ONLY
LONG WOODEN STICKS OR BRANCH AFTER ENGINE 1S
SHUT OFF AND ALL MOVING PARTS HAVE COMPLETELY
STOPPED AND SPARK PLUG WIRE HAS BEEN
DISCONNECTED.
- ALWAYS WEAR ANSI 287.1 APPROVED SAFETY GOGGLES
AND ANSI 3.19 APPROVED EAR PROTECTION.
= AVOID WEARING LOOSE FITTING CLOTHING. 9
AA DANGER
DO NOT START ENGINE
UNLESS BELT COVER 15
SECURELY ATTACHED.
SEE OPERATOR'S MANUAL
FOR FULL SAFETY AND
MAINTENANCE INSTRUCTIONS.
Part Number 740661100
A DANGER
ROTATING CUTTER BLADES. DO NOT OPERATE
UNIT WITHOUT BAG OR OPTIONAL BLOWER
ATTACHMENT PROPERLY INSTALLED.
ROTATING BLADE
DO NOT PUT HANDS OR FEET UNDER OR
INTO UNIT WHEN ENGINE (S RUNNING.
— A
—— 4
Part Number 740660900
THROWN OBJECTS
BEFORE USING, CLEAR AREA OF PEOPLE AT
LEAST 50 FT. (15M) AND REMOVE OBJECTS
THAT MAY BE THROWN BY BLADE.
DO NOT OPERATE UNIT WITHOUT DISCHARGE CHUTE,
BAG AND DEFLECTOR FIRMLY IN PLACE.
Part Number 740660600
À DANGER A CAUTION
\ 6 , / READ OPERATOR'S MANUAL BEFORE
1. D0 NOT PUT HANDS INTO UNIT WHEN
ENGINE IS RUNNING.
2. DO NOT PUT ANY BRANCHES OVER 3 IN.
OPERATING UNIT. DO NOT DEPOSIT
BRANCHES LARGER THAN 1/2 INCH
ROTATING CUTTING BLADES.
DO NOT PUT HANDS OR FEET INTO
INLET OPENINGS WHEN ENGINE IS
(13MM) DIAMETER INTO HOPPER.
WEAR ANSI 787.1 APPROVED
SAFETY GOGGLES AND ANSI 3.19
3. ANSI 287.1 APPROVED
(75MM) IN DIAMETER INTO CHIPPER.
SAFETY GOGGLES
CHOULD BEWORNWHEN OPERATING THIS
APPROVED EARPROTECTION. AVOID
LOOSE FITTING CLOTHING. DO NOT
OPERATE HOPPER IN POSITIONS
TO AVOID SERIOUS PERSONAL INJURY, STOP
RUNNING. ENGINE, REMOVE SPARK PLUG WIRE, ALLOW
ENGINE TO COME TO A COMPLETE STOP
BEFORE CLEARING OBSTRUCTION OR
MAKING ADJUSTMENTS.
TO AVOID SERIOUS PERSONAL
INJURY, STOP ENGINE, REMOVE
SPARK PLUG WIRE, ALLOW ENGINE
TO COME TO A COMPLETE STOP
BEFORECLEARING OBSTRUCTION OR
MAKING ANY ADJUSTMENTS.
OTHER THAN RECOMMENDED IN THE
OPERATOR'S MANUAL.
NO HANDS BELOW THIS LINE
Part Number 740660700
NO HANDS BELOW THIS LINE
UfA a
Part Number 740660500
J
ECHO
PARTS CATALOG
To obtain a parts catalog send a check or money order for $2.00 per parts book made payable to ECHO, INCORPORATED.
Include a sheet of paper stating your name and address and specify
CSV3, CSV5S, CSV8S Part Number 9992220264 1
Mail to:
ECHO,INCORPORATED
400 OAKwooD Roap
LAKE ZURICH, IL 60047
Please allow three to four weeks for delivery
ECHO
ECHO, INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047
99922202699
9/95
">