QUICK INSTALLATION GUIDE
Remote Management Card
RMCARD302
I
ntelligent Remote Management Card allows a UPS system to be managed, monitored, and configured
K09-0000057-01
LINK Indicator
Ethernet connector
RX/TX Indicator
Definitions for LED Indicators
Link LED color
Off
Condition
The Remote Management Card is not connected to the Network or the Remote
Management Card power is OFF
On(Yellow) The Remote Management Card is connected to the Network
TX/RX LED color
Off
On(Green)
The Remote Management Card power is OFF
The Remote Management Card power is ON
Flash
- Receiving/transmitting data packet
- Reset finished
Step 2. Configure the IP address for the CyberPower
Remote Management Card.
Method 1: Using the Power Device Network Utility Tool
1. Install the Power Device Network Utility Tool from the included CD. It is located on the CD in the \tools\nework folder. Double click the
“Power Device Network Utility” installation file, “Setup.msi” to begin the installation.
2. After installation is completed, run the “Power Device Network Utility” program. (Under “All Programs”, select “CyberPower Power Device
Network Utility”).
3. The main dialog of the Power Device Network Utility Tool program is shown in Figure 1. The tool will display all Remote Management
Cards present on the network. The "Refresh" button is used to search the entire local network again.
INSTALLATION GUIDE
Step 1. Hardware Installation
1. Turn off the UPS before removing the expansion port cover on the UPS.
2. Remove the two retaining screws of the expansion port cover then remove the cover.
3. Install the CyberPower Remote
Management Card into the expansion port.
4. Re-install and tighten the retaining screws.
5. Connect the Ethernet cable to the LAN port of the
CyberPower Remote
Management Card.
6. Turn on the UPS.
Figure 1. The main window of the “Power Device Network Utility” program.
4. Select the Remote Management Card you are setting up. Click on the
Tools menu and select “Device Setup” or double click the Remote
Management Card you want to configure.
5. You can modify the IP Address,
Subnet Mask, and Gateway address for the Device MAC
Address listed in the Device
Network Settings window, as shown in figure 2. The default IP
Address is 192.168.20.177 and the default Subnet Mask is
255.255.255.0.
Figure 2. The Device Network setting window.
6. Modify the IP, subnet mask or gateway address. Enter the new addresses into the corresponding fields.
7. You will need to enter a User
Name and Password for the
Remote Management Card in the authentication window, as shown in figure 3.
*Default user name: cyber;
Default password: cyber.
8. If IP address is successfully, you will see a message that the IP set up is OK, as shown in figure 4.
Figure 3. Authentication window.
Figure 4. Setup IP Address successfully message.
Method 2: Using a command prompt
1. Obtain the MAC address from the label on the Remote Management
Card. Each Management Card has a unique MAC address.
2. Use the ARP command to set the IP address.
Example:
To assign the IP Address 192.168.10.134 for the Remote Management
Card, which has a MAC address of 00-0C-15-0A-0A-0A you will type in the following command prompt from a PC connected to the same network as the Remote Management Card.
(1) Type in “arp-s 192.168.10.134 00-0C-15-0A-0A-0A” then press
Enter.
3. Use the Ping command to assign a size of 123 bytes to the IP.
(1) Type in “ping 192.168.10.134 -l 123” then press Enter
(2) If the replies are received, your computer can communicate with the
IP address.
WEB INTERFACE Login Account
There are two user account types.
- Administrator (default username: cyber; default password: cyber)
- Viewer (default username: device; default password: cyber)
The administrator can access full functions, including enable/disable the
Viewer account, and the viewer can access the read function but can not control or change any setting.
Trouble Shooting
Problem
Unable to configure the Remote
Management Card by method 1 or method 2
Solution
1. Check the LED status , the normal condition is both yellow and green led are on.
If green led is off :
►Check if the Remote Management Card is properly seated in the UPS and the UPS power is on.
If yellow led is off :
►Check if the network connection is valid.
2. Check if the operated PC is on the same physical network as Remote Management
Card is.
Unable to ping the Remote
Management Card
Lost the user name and password
1. Use method1 and method2 to get correct IP address of the Remote Management Card.
2. If the operated PC is on the different physical network from the Remote Management Card, verify the setting of subnet mask and the IP address of gateway.
Please refer to the “ Reset to Default Setting /
Recover from a Lost Password” part in the user’s manual.
Conformance Approvals
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY
RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED TO
THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
CyberPower North America
CyberPower Systems (USA), Inc.
Phone: (952)-403-9500 Toll-free: (877)297-6937
4241 12th Avenue E. Suite 400, Shakopee, MN 55379
E-mail: [email protected]
Website: www.CPSww.com
CyebrPower Europe
CyberPower Systems, Inc.
E-mail: [email protected]
Website: www.cpsww.eu
CyberPower Systems France
Z.I. Saint Séverin 28220 CLOYES sur le Loir – France
Tél : +33(0)2 37 98 61 50
E-mail : [email protected]
