DSB CB-240 Operating instructions
Add to my manuals
1 Pages
DSB CB-240 is a versatile binding machine capable of punching and binding documents up to 240 sheets (80gsm) or 2 sheets of 0.2mm PVC covers. It features 24 selectable punch pins, allowing you to customize the number of holes for different paper sizes, including Legal, A4, and Letter. The adjustable paper edge guide ensures precise alignment, while the plastic comb guide helps you select the correct comb size for your document thickness. With its two-handle design, you can punch and bind simultaneously, saving you time and effort.
advertisement
Operating instructions
CB-240
Operating instructions
CB-240
14
1
2
3
4
5
1
L
Instruction manual. . . . . . . . . . . . . . . . . .
Thanks for your purchase.Please carefully read through, this introduction before use and keep it for future reference.
14 13 12 11 10
9 8 7 6
Description of components
7
8
9
10
11
12
13
14
Circulating punching lever : Removable and reassemble handle bar for both extra large and normal format papers.
Dust cover : Keep the dust falling into the machine
Blades : All blades may be disengaged by pulling them upward manually.
Punching slot : For US pitch 21 ring plastic comb.
Paper edge guide : Left or middle or right 3 steps adjustable punching depth
Plastic comb guide : Determining the binding comb size for your document.
Metal comb holding fingers : To hold the plastic comb for opening.
Metal hooks : Open plastic comb by hooking the finger rings.
Paper stopper-1 : Pushing frontward for punching normal format paper, pushing backward extra large paper.
Paper stopper-2 : By switching left or right for different format paper.
Plastic comb opening lever : Open plastic comb by pulling the lever.
Waste bin : Collects waste paper chips
(WARNING! Be Sure to Clean Waste Bin Frequently. Overloaded Waste Chips Could Cause
Punching Jam and Machine Damage.)
Metal pin : A guide pin for punching extra large paper.
Screws : For dividing the circulating punching lever.
1.
1
1
L
3
R
2
CB-240
R
1
R
2
4
L
3
4
2
3
4
R
4
5
2.
Operating instructions
CB-240
The machine is designed for binding using plastic binding combs of 6~51 mm. From the following table you can read off the appropriate binding comb size for the number of sheets you are binding.
Binding comb dia. 6 8 10 12 14 16 20 22 25 28 32 38 44 50
Max. No. of sheets 25 45 65 95 125 145 175 210 240 270 310 375 440 500
General notes
You should initially carry out sample punching using waste paper. Remember that the maximum punching capacity is 25 sheets. This specification refers to 80-g-paper (corresponds to the thickness of commercial copying paper). Punch transparent film and cardboard backs individually.
A scale is drawn on the front plate, with which you can determine the thickness of the document to be bound(plastic comb guide). Therefore you can easily select the binding comb with the correct width.
Before punching and binding
How to punch
Punch US pitch for Legal, A4 or LTR Paper Format
2
1
3
Figure-1 (select plastic comb size)
Hold your document tightly straight,
Align Right end to get correct measurement of document thickness and select proper plastic comb.
Backward
Right
Left
Middle
Figure-2 (select punching slot)
5
2.
Right for plastic comb dia.
6~12mm .
3.
Middle for plastic comb dia.
14~22mm .
4.
Left for plastic comb dia.
14~51mm .
Left
Right
Frontward
3.
Figure-3 (page stopper-1)
9
punching normal paper format.
2.Move Pape stopper-1 frontward for
punching extra large paper.
Figure-4 (page stopper-2)
1.Punching the normal paper, you can move
Page stopper-2 left or right for different
paper format.
10
2.Make Page stopper-1 align paper format line.
4
Figure-5
1
9
4
left-align to the page stopper-1 .
2 1
strongly with both hands to punch the sheets.
(Note: max.25 sheet 80gsm paper or 2 sheets
PVC cover)
Punch US pitch Extra Large Paper Format
Figure-6
3 Lift up the circulating punching lever .
4 Take out the sheets.
3
1 Move the page stopper-1 down.
2 Align the sheets to A3 line .
3 Press down the single handle lever.
1
2
5
4
4 Reverse the punched sheets, insert the third
right end punched hole to the extended metal
3 Red area part), remain two holes
at the right side of extended metal pin .
5 Press down the single handle lever.
3
4.
CB-120
DSB Commercial Binding
System
Color Ginny
CB-3000
Comb Well
CB-230
8.
Technical Data:
Model No.
Operating method
Paper size
CB-240
Manual
Legal, A4, LTR and extra large up to 700mm width
Edge guide
Punches
Punching capacity
Binding comb size
Adjustable in three steps (2.5, 4, 5.5mm)
24 Selectable punch pins
25 sheets (80gsm paper), 2 sheets PVC 0.20 mm
6mm~51mm(500 sheets)
Loading of paper
Paper guide line
Vertical
Multiple(Legal,A4,LTR,A3)
Punching & Binding Two handles device accept same time operation
Net weight
Dimensions
15Kg
440×480×160(B×D×H)
How to bind
1
Figure-9
1 Inserting the plastic binding comb in the
7
the side to be opened upward.
Figure-10
2 Pull the Plastic Comb Opening lever 11
far enough forward So that the binding
Comb is opened widely.
3 Lay the paper over the comb fingers.
3
2
5
4
How to disengage the blades
Depending on the paper format, it is possible to
Disengage any of the 24 blades. to do this, pull the
Unneeded blades upwards. the number of blades needed For the format being used is given as followed: Legal/14" with 24 punch holes; A4 with
21 punch holes; LTR with 19 punch holes.
Figure-11
4 To close the binding comb, push the
plastic comb opening lever 7 downwards .
5 Remove the bound document.
5.
Punching depth adjustment
1. Set the Paper Edge Guide to the Right position (seen from the front) for documents with
comb binding size 6mm to 12 mm. This setting corresponds to the standard setting.
2. Set the Paper Edge Guide to the Middle position (seen from the front) for documents with
comb binding size 14mm to 22 mm. The large punching depth prevents tearing of the bound
document.
3. set the Paper Edge Guide to the Left position (seen from the front) for documents with
comb binding size 25mm to 51 mm. The large punching depth prevents tearing of the bound
documents.
This is how you punch and bind the sheets of yours document
1. Select a sufficient size of plastic binding comb according to the paper amount (see plastic
comb guide ; Ref.figure-1).
2. Place the plastic binding comb into the Metal Comb Holding Fingers with the open side
upwards.
8
7
4. The rings are opened by the Metal Hooks of the comb by pulling the binding back slowly
forwards. Stop if the binding comb is opened far enough. The binding comb remains in the
selected position.
5. Put the sheets you want to punch left aligned to the page stopper-1 and push them straight
4 10
9
into the punching slot . The page stopper-2 is manually adjustable to different formats.
You can use the page stopper-1 for 24 ring punching or for 4-fold punching by moving the
page stopper-1 frontward or backward.
6. Press the circulating punching lever down strongly with both hands to punch the sheets of
8. Close the binding comb by pushing the plastic comb-opening lever back. You can then
remove the bound document.
1
your document.
7. Place the punched sheets in the correct sequence into the opened binding comb.
11
This is how you punch sheets Extra Large Paper Format
1. Loosen 2 screws on the side of the device.
2. Remove the longer part of the lever from the machine.
3. The punching lever can now only be operated with one hand.
4. Place the already punched page into the punching slot in such a way that you can press
one of the holes over the metal pin at the lower end of the slot. This ensures that all holes
have the same distance.
13
5. Now punch the remainder of the total punching width.
6. Screw the punching lever together again, when you have finished.(refer to "quick tip ......")
This is how you exchange pages of your bound document
1. Place the plastic binding comb (document with writing forwards) into the metal comb holding
fingers . Pull the plastic binding comb with the bound document between the metal comb
holding fingers and lock it into the metal hooks .
2. Press the binding comb carefully backwards until the plastic binding comb opens slightly.
3. You can remove or exchange sheets, when the spiral fingers have opened by approx.4-5 mm.
4. Then close the plastic binding comb by pushing the plastic comb-opening lever .
6.
Empty the waste bin
12
2
1
Figure-13
1 Remove the waste bin completely.
2 Empty the waste chips entirely.
3
3 Push the Waste Bin back into the machine.
Warning! Overloaded waste chip in the bin might cause punching jam and machine damage.
Maintenance and care
1. You should regularly empty the waste bin .
2. Films or cardboard should be punched separately.
3. Use the device only for punching paper, cardboard and protective sheets.
7.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project